// blog
PPBUS_G3H Known-Good Readings on 33 MacBook Boards
PPBUS_G3H is the main always-on power rail on MacBook boards. Across 33 boards in OpenBoardData, it reads 8.5 to 8.6 V on the two-cell boards and 12.2 to 13.1 V on the three-cell ones. In diode mode, the 8.6 V boards read about 0.11 to 0.17 and most others 0.33 to 0.51. Compare with your own board’s number before deciding anything.

PPBUS_G3H is the first rail to check on a MacBook board that won’t start. It’s the main power bus, there as soon as a charger or battery is connected (G3H means always on), and nearly everything else is made from it.
The trouble with a single known-good number is that it depends on the board. Here’s PPBUS_G3H on every board in OpenBoardData that has it, side by side.
Two kinds of board
The voltage splits the boards in two. Some run PPBUS_G3H at about 8.6 V, the rest at about 12.5 to 13.1 V, which matches a two-cell or a three-cell battery. And the diode reading follows: the 8.6 V boards read about 0.11 to 0.17, most of the others 0.33 to 0.51.
So a diode reading of 0.13 on PPBUS_G3H can be perfectly normal on one board and a short on another. Look up your own board’s number before you start lifting parts.
The readings
Diode readings are in diode mode with the board unpowered; voltages with the charger connected. A dash means the archive has no value. Values are as contributors entered them.
| Board | Diode | Voltage |
|---|---|---|
| 820-00164 | 0.114 | 8.520 |
| 820-00165 | 0.128 | 8.600 |
| 820-3435 | 0.148 | 8.540 |
| 820-3437 | 0.165 | 8.500 |
| 820-4924 | 0.130 | – |
| 820-3462 | 0.140 | 12.800 |
| 820-3476 | 0.161 | 12.500 |
| 820-00045 | 0.398 | – |
| 820-00239 | 0.445 | 13.100 |
| 820-00244 | 0.360 | – |
| 820-00281 | 0.450 | 13.100 |
| 820-00840 | 0.450 | 13.100 |
| 820-00850 | 0.460 | 12.220 |
| 820-00875 | 0.416 | 13.100 |
| 820-00923 | 0.460 | 13.100 |
| 820-00928 | 0.360 | 13.100 |
| 820-01041 | 0.354 | 12.520 |
| 820-01124 | 0.663 | – |
| 820-01521 | 0.455 | 12.540 |
| 820-01598 | 0.474 | 12.600 |
| 820-01700 | 0.415 | 12.600 |
| 820-01814 | 0.434 | 12,600 |
| 820-01949 | 0.510 | 13.100 |
| 820-01958 | 0.410 | 13.050 |
| 820-01987 | 0.336 | 12.600 |
| 820-2850 | 0.47 | – |
| 820-2915 | – | 12.500 |
| 820-2936 | 0.434 | – |
| 820-3023 | 0.435 | – |
| 820-3115 | 0.450 | 12.490 |
| 820-3332 | 0.445 | – |
| 820-3662 | 0v45 | – |
| 820-3787 | 0.449 | 12.500 |
Two boards break the pattern: the 820-3462 and 820-3476 read 0.14 and 0.16 in diode mode at 12.5 V or more. That’s what their contributors measured; it’s a reminder that the pattern is a starting point, not a rule.
Reading it right
A few things change a diode reading. Which way round the probes go, the meter, and what’s still connected: a battery or a fan left plugged in can shift it. Several boards also have readings listed for different CPU and memory versions, which the board pages show. These are community numbers, so treat them as a guide. A reading a little off isn’t a fault on its own.
The rest of the rails
PPBUS_G3H is one rail. Each board’s page lists every rail by startup stage, PP3V42_G3H and the standby rails next, with their known-good readings, and an AI note on each that explains what the rail is and how to check it. Open your board file in the free Board Viewer and the same readings show on the pins as you probe.
The readings are OpenBoardData’s contributors’ work, under the Open Database License. To add your own, use their site.
































































































































