Apple laptop board · OpenBoardData

820-00164 known-good readings

Known-good readings for the Apple laptop board 820-00164: 145 nets, including 34 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 34 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00164.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 34 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 9

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.2953.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail; the G3H suffix in its name indicates it should be present whenever power is connected. Known-good readings in the archive: diode 0.295 to ground and 3.400 V with power applied. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good resistance reading here. A diode far below 0.295 suggests a short or leaky load on the rail; a voltage well off 3.400 V points to the rail not regulating or being loaded down, but confirm with a second measurement before suspecting a part.

PPBUS_G3H0.1148.520–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the always-on main bus rail, judged from its name (G3H = always on). The archive lists a known-good diode reading of 0.114 and a voltage of 8.520; treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.114 usually points to a short or a leaky part on the rail; a voltage far from 8.520 points to a problem upstream in the rail's source. No known-good resistance reading is listed for this rail.

PPBUS_G3H_R0.1148.520–
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main bus rail that is always on, going by the G3H in its name (general naming, not from board data). The archive lists a diode reading of 0.114 and a voltage of 8.520 for it; treat these as a community guide, since readings vary with board state and no condition is recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.114 usually points to a short or a leaky part on the rail; a voltage well off 8.520 points to a problem in the circuit feeding it. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

PPDCIN_G3HOL14.600–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, judging from its name. In the readings archive it shows diode OL and 14.600 V; the archive gives no condition for those readings, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A voltage far below 14.600 V points to a problem upstream in the adapter or input path rather than at this rail; no known-good resistance reading is available here.

PPDCIN_G3H_CHGR0.62014.800–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H suffix indicates an always-on rail, from the name. Archived readings for this net are diode 0.620 and voltage 14.800, as a guide only since community readings vary with board state. Check it unpowered in diode mode from the net to ground, then with power applied measure the voltage. A diode reading far below 0.620 suggests a short or leaky part on the rail; a voltage well off 14.800 points at the input or charger supply. No known-good resistance reading is available here, so compare against a matching net or a known-good board.

PPDCIN_G3H_INRUSH0.62014.800–
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is the always-on G3H input rail, judging from its name: the DC input side, with "INRUSH" suggesting the inrush/input path. Known-good readings here are diode 0.620 and voltage 14.800; no resistance reading is known for this rail.

  • Check it unpowered in diode mode from the rail to ground; 0.620 is the guide.
  • Then apply power and measure the voltage; 14.800 is the guide.
  • A diode reading far below 0.620 usually points to a short or leaky part on the rail; a voltage well off 14.800 points to a problem upstream in the input path.

These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PPDCIN_G3H_ISOLOL14.600–
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is the isolated DC-input rail; the G3H part of the name indicates it is always-on, and ISOL suggests it sits on the isolated side of the input path. The archived readings for this rail are a diode reading of OL and a voltage of 14.600. Check it unpowered in diode mode from the rail to ground, then measure its voltage with power applied. OL in diode mode is the recorded value here, so it is not by itself a fault sign; a voltage far from 14.600 with power applied points to a problem in the input supply or the path feeding this rail. No known-good resistance reading is recorded for this rail.

PPVBAT_G3H_CHGR_REG0.1118.600–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From the name, PPVBAT_G3H_CHGR_REG is a charger-side regulated rail derived from the battery/DC-in side, and the G3H part means it's an always-on rail present as soon as power is applied.
  • Known-good readings (community archive, a guide only): diode 0.111 to ground, voltage 8.600.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground; then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open connection. Wrong voltage with a normal diode reading points more toward the charger circuit feeding it. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PPVIN_G3H_P3V42G3H0.30614.280–
AI: what PPVIN_G3H_P3V42G3H is and how to check it
  • What it is: From its name, PPVIN_G3H_P3V42G3H is the always-on (G3H) input feed to the P3V42G3H rail — the main adapter/DC-in side that stays live whenever power is connected.
  • Known-good readings (community archive, guide only): diode 0.306 to ground, voltage 14.280 with power applied.
  • How to check: Power off and unplugged, diode mode from the net to ground for the 0.306; then apply power and measure the voltage for the 14.280.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; no voltage points upstream toward the input path. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

S5 and SUS: standby 2

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S5_REG_R0.330––
AI: what PP3V3_S5_REG_R is and how to check it

PP3V3_S5_REG_R is a 3.3 V standby rail; the S5 and SUS in the name indicate it belongs to the standby stage (from the name). The archive lists one known-good reading: diode 0.330 in diode mode to ground, with no condition recorded. No known-good voltage reading is listed here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.330; then apply power and check the voltage. A diode reading far below 0.330 usually suggests a short or leaky load on the rail, but one reading isn't proof a part is bad, so confirm before replacing anything.

PPBUS_S5_HS_COMPUTING_ISNS0.111––
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From its name, PPBUS_S5_HS_COMPUTING_ISNS is a PPBUS rail section feeding high-side computing circuitry in the S5 standby state. The ISNS suffix usually means a current-sense node (general naming convention, not from this board's data).
  • Known-good reading: Diode mode to ground is 0.111 in the archive. That is a community value and a guide only; no known-good voltage reading is recorded here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below known-good often points to a shorted load or component on that rail, but one reading doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.

S4 3

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S4SW_SNS–3.300–
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail in the S4 startup stage, both from its name; "SW" and "SNS" suggest a switched rail with a sense line, which is general interpretation, not board data. The only known-good figure here is 3.300 V, with no condition recorded, and there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage. A voltage far from 3.300 V points to the rail not coming up or being loaded down, but with no known-good diode value that reading can only be judged against a matching net or a known-good board.

PP5V_S4RS30.436––
AI: what PP5V_S4RS3 is and how to check it

PP5V_S4RS3 is a 5 V rail in the S4 startup stage, judged from its name. The only known-good reading here is a diode value of 0.436 to ground; no voltage reading is recorded.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.436.
  • Then power the board and measure the voltage on the rail.
  • A diode reading far below 0.436 usually points to a short or a leaky part on the rail; far above it can mean an open path. A missing or low voltage under power points to the rail not being enabled or its source failing.
  • These are community readings and vary with board state, so treat them as a guide, not a verdict.
PPVIN_S4SW_TBTBST_FET0.468––
AI: what PPVIN_S4SW_TBTBST_FET is and how to check it

PPVIN_S4SW_TBTBST_FET is a power input rail for the Thunderbolt boost (TBTBST) FET, and the S4 in its name marks it as an S4-stage rail — both from the name, not from board data. The only known-good reading here is a diode value of 0.468; no voltage or resistance reading is recorded for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on it. A diode reading far from 0.468 usually points to a short or a leaky component on the rail, but a single reading isn't proof a part is bad — confirm with the voltage and compare against a known-good board.

S3: memory 6

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S30.202––
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail, and the S3 suffix indicates the memory stage of startup (from the name). The archive lists a known-good diode reading of 0.202 to ground; no known-good voltage reading is recorded here.

  • Check it unpowered in diode mode from PP1V2_S3 to ground, then measure the voltage with the board powered and running.
  • A diode reading far from 0.202 usually points to a short or a damaged component on that rail; a voltage far off 1.2 V points to the rail not coming up.
  • These are community readings and vary with board state, so treat them as a guide and compare against a matching rail or a known-good board before condemning a part.
PP1V8_S3_REG_R0.344––
AI: what PP1V8_S3_REG_R is and how to check it

PP1V8_S3_REG_R is a 1.8 V S3 (memory-stage) regulated rail, judged from its name. The archive lists a known-good diode reading of 0.344 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.344 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection. The 0.344 is a community guide and varies with board state, so confirm against a matching rail or a known-good board before replacing anything.

PP3V3_S3RS0_CAMERA0.3553.300–
AI: what PP3V3_S3RS0_CAMERA is and how to check it

PP3V3_S3RS0_CAMERA — a 3.3 V rail for the camera, and the S3 in its name places it in the memory (S3) startup stage; that's from the name, not from a schematic.

  • Known-good (community archive, guide only): diode 0.355 to ground, voltage 3.300.
  • Check with the board unpowered: diode mode, black probe to ground, red to the rail. Then power up and measure the voltage.
  • A diode reading well below 0.355 suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points upstream, at the rail's source or enable.
  • No known-good resistance reading exists here; compare against a matching rail on a known-good board if needed.
PP3V3_S3RS0_CAMERA_R–3.300–
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it

PP3V3_S3RS0_CAMERA_R is a 3.3 V rail that, from its name, belongs to the S3 (memory) startup stage and feeds camera circuitry; the "RS0" and "R" suffixes suggest a switched or gated branch. The archive lists a known-good voltage of 3.300 V for this rail, with no condition noted and no known-good diode or resistance reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far below 3.3 V points to the rail not being enabled or its source missing; a near-short diode reading suggests a fault on the rail itself. These are guides only, so compare against a matching rail or a known-good board before condemning anything.

PP5V_S3RS0_ALSCAM_F0.440––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it
  • What it is: From its name, PP5V_S3RS0_ALSCAM_F is a 5V rail that comes up in the S3 (memory/suspend) stage and feeds the ALS camera circuit. The "_F" suffix usually marks a filtered or fused version of the rail (general naming convention, not from this board's data).
  • Known-good reading: diode 0.440 to ground, from the readings archive. This is a community guide, not a guaranteed value, and no voltage or resistance reading is recorded here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a much higher or open reading points to a broken feed or missing enable. Confirm with the voltage reading before replacing anything.
PPDDR_S3_REG_R0.202––
AI: what PPDDR_S3_REG_R is and how to check it

PPDDR_S3_REG_R is a memory-rail enable/regulator signal in the S3 (memory) startup stage, judged from its name. The only known-good reading here is a diode value of 0.202 to ground, board unpowered; no known-good voltage or resistance is recorded. Check it with the board off in diode mode from the net to ground, then power up and measure the voltage. A diode reading far from 0.202 suggests a short or open on that net rather than a confirmed bad part, so compare against a matching net or a known-good board before replacing anything.

S0: running 14

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S0_REG_R0.072––
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V rail that runs in the S0 (fully on) state, judged from its name; the "_REG" suffix suggests it comes from a regulator output. The archive lists a known-good diode reading of 0.072 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in S0. No known-good voltage reading is listed here, so compare against a matching rail or a known-good board. A diode reading far from 0.072 usually points to a short or a faulty load on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S00.3633.300–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, judging by its name; it should be present once the board is fully on. In the readings archive the known-good values are a diode reading of 0.363 to ground and 3.300 V with power applied — these are community readings and only a guide. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.363 usually suggests a short or a failing part on the rail; a voltage well under 3.300 V with the board powered points to the rail not coming up or being loaded down. No known-good resistance reading is listed here.

PP3V3_S0_FAN0.3503.300–
AI: what PP3V3_S0_FAN is and how to check it

PP3V3_S0_FAN is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "FAN" suggests it feeds fan circuitry (from the name only).

  • Known-good readings for this rail: diode 0.350 to ground, and 3.300 V with power applied. These are community readings and a guide, not a guarantee.
  • To check it: power off, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • A diode reading far from 0.350 usually points to a short or a leaky part on that rail; a voltage well below 3.300 V with power on suggests the rail isn't coming up or is loaded down.
  • No known-good resistance reading is recorded here.
PP3V3_S0SW_LCD0.537––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is the switched 3.3 V LCD rail: the "S0" part of the name says it belongs to the running state, and "SW" suggests it is switched on rather than always present (from the name, not from board data).

  • Known-good: diode 0.537 on this net, from the readings archive. No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe to ground, red probe on the net. Then apply power and measure the voltage on the net.
  • A diode reading far from 0.537 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part; compare with the matching net or a known-good board before replacing anything.
PP3V3_S0SW_LCD_UF0.537––
AI: what PP3V3_S0SW_LCD_UF is and how to check it

PP3V3_S0SW_LCD_UF is a switched 3.3 V LCD rail, from its name: an S0 (running-state) supply, switched, for the LCD. The archive lists one known-good diode reading of 0.537 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.537 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path; confirm with the voltage before replacing anything.

PP3V3_S0SW_SSD0.480––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a 3.3 V rail switched on in the S0 (running) state, judging by its name; the "SSD" part suggests it feeds the SSD supply on this board. The archive lists one known-good diode reading of 0.480 to ground, with no condition noted, and no known-good voltage reading here.

  • Check it unpowered: diode mode from the rail to ground, board off and unplugged. A value near 0.480 is the guide; far lower usually points to a short or a failing part on the rail.
  • Then power the board and measure the voltage in S0. No known-good voltage is recorded here, so compare against the rail's expected 3.3 V and a matching rail on a known-good board.

A reading far off the diode value suggests a shorted load or component on that net, but one reading alone doesn't confirm a bad part.

PP3V3_S0SW_SSD_FLT0.480––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a 3.3 V rail switched on in the S0 (running) state, feeding the SSD; that meaning comes from the rail's name, not from a schematic. The archive lists one known-good diode reading of 0.480 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then confirm about 3.3 V with the board powered in S0; no known-good voltage reading is listed here. A diode value far from 0.480 usually points to a short or a leaky part on that rail, but one reading alone doesn't prove a part bad, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S00.4405.100–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail for the S0 (running) state, as the name indicates. The archive lists diode 0.440 and voltage 5.100 for it, with no condition noted, so treat these as a guide only.

  • Check it unpowered in diode mode from PP5V_S0 to ground; a far lower reading suggests a short or leaky load on the rail, a far higher one an open path.
  • Then power the board and measure the voltage; it should sit near 5.1 V when the board is in S0.
  • No known-good resistance reading exists here, so compare with a matching rail or a known-good board.
  • A voltage well off 5.1 V points to the rail's supply or its enable, not confirmed until traced.
PPHV_S0SW_LCDBKLT0.538––
AI: what PPHV_S0SW_LCDBKLT is and how to check it

PPHV_S0SW_LCDBKLT is the LCD backlight switch rail on the 820-00164; the S0 in the name indicates it belongs to the running state, and LCDBKLT marks it as backlight-related (from the name, not from a schematic). The only known-good reading in the archive is a diode value of 0.538 to ground, with no condition recorded, and there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.538 usually points to a short or a leaky component on that rail, but a single reading is only a guide, so confirm with a voltage measurement before replacing anything.

PPVCC_S0_CPU_PH10.006––
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 is a CPU power rail, a phase (PH1) of the CPU core supply that runs in the S0 state, from its name. The archive lists a known-good diode reading of 0.006 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on it with power applied and the board in S0. A diode reading far above 0.006 usually points to an open or missing connection on that phase, while a short to ground reads near zero; a small difference may be normal, so compare with the other CPU phases before suspecting a part.

PPVCC_S0_CPU_PH20.006––
AI: what PPVCC_S0_CPU_PH2 is and how to check it

PPVCC_S0_CPU_PH2 is a CPU power rail phase, from its name: the S0 part means it's live in the running state, and PH2 marks it as one phase of the CPU VCORE supply. The archive lists a diode reading of 0.006 for it, with no condition noted; there is no known-good voltage or resistance reading here. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.006 usually points to a short or a damaged phase component, but a single reading doesn't confirm a bad part, so compare against the other CPU phases before replacing anything.

PPVIN_S0SW_LCDBKLT0.390––
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the switched input feed for the LCD backlight, going by its name (S0 = running state, SW = switched, LCDBKLT = LCD backlight). The only known-good reading here is a diode value of 0.390 to ground, with no condition given; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered and the display connected.
  • A diode reading far below 0.390 suggests a short or leaky part on the rail; far above it suggests an open path.
  • A missing or low voltage with power applied points to the backlight enable or switch circuit upstream rather than the rail itself.

These readings are community contributions and a guide only, so a small difference may be normal.

PPVIN_S0SW_LCDBKLTFET0.131––
AI: what PPVIN_S0SW_LCDBKLTFET is and how to check it

PPVIN_S0SW_LCDBKLTFET is the switched input feed to the LCD backlight circuit; the name indicates an S0 (running-state) rail, and the SW/FET part suggests it's the node after a backlight power switch. The only known-good reading in the archive is a diode value of 0.131 to ground, with no condition recorded; there is no known-good voltage or resistance value here.

  • Check it unpowered in diode mode from the net to ground, then power the board and measure the DC voltage on it.
  • A diode reading far from 0.131 usually points to a short or leaky component on that node, but a single reading isn't proof of a bad part.
  • No voltage reference is available, so compare against a matching net or a known-good board of the same model.
PPVMEMIO_S0_CPU0.202––
AI: what PPVMEMIO_S0_CPU is and how to check it

PPVMEMIO_S0_CPU is a memory I/O power rail for the CPU, judged from its name; the S0 suffix indicates it belongs to the running state. The only known-good figure here is a diode reading of 0.202 to ground, with no condition recorded and no voltage or resistance value available. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.202 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
BKL_EN0.574––
BKL_FLTR0.572––
BKL_FSET0.574––
BKL_ISEN10.646––
BKL_ISEN20.646––
BKL_ISEN30.646––
BKL_ISEN40.643––
BKL_ISEN50.643––
BKL_ISEN60.644––
BKL_ISET0.573––
BKL_PWM0.547––
BKL_SCL0.495––
BKL_SDA0.496––
BKL_VSYNC_R0.572––
CAM_PWR_SEL0.824––
CAM_SENSOR_WAKE_L0.818––
CAM_SENSOR_WAKE_L_CONN0.002––
CAM_TEST_OUT0.823––
CHGR_AGATE_DIV–6.000–
CHGR_CSI_R_N0.620––
CHGR_CSI_R_P0.620––
CHGR_PHASE0.1138.600–
CHGR_RST_L–3.300–
CHGR_SGATE_DIV–5.600–
CPUVR_PHASE10.006––
CPUVR_PHASE20.006––
DCIN_ISOL_GATE–6.760–
DCIN_ISOL_GATE_R–6.760–
EDP_BKLT_PWM0.554––
FAN_RT_PWM0.718––
FAN_RT_TACH0.6471.600–
GND0.000––
I2C_CAM_SCK0.423––
ISNS_AIRPORT_N0.518––
ISNS_AIRPORT_P0.518––
KBDLED_SW0.414––
LCDBKLT_BOOST0.390––
LCDBKLT_EN_L0.923––
LED_RETURN_10.646––
LED_RETURN_20.646––
LED_RETURN_30.647––
LED_RETURN_40.643––
LED_RETURN_50.643––
LED_RETURN_60.645––
MEM_CAM_ZQ_S20.292––
MEM_EVENT_L–3.400–
MIPI_CLK_CONN_N0.391––
MIPI_CLK_CONN_P0.391––
MIPI_CLK_N0.389––
MIPI_CLK_P0.389––
MIPI_DATA_CONN_N0.390––
MIPI_DATA_CONN_P0.390––
MIPI_DATA_N0.388––
MIPI_DATA_P0.388––
P1V2_CAM_SRVLXC_PHASE0.272––
P1V05S0_LL0.072––
P1V5S0SW_AUDIO_EN–3.200–
P1V8S3_SW0.344––
P1V35_CAM_SRVLXD_PHASE0.215––
P3V3_S5_CSP2_R–3.300–
P3V3_S5_REG_L0.330––
P3V42G3H_BOOST–7.220–
P3V42G3H_FB–1.200–
P3V42G3H_SHDN_L–14.290–
P3V42G3H_SW0.2953.400–
P5V_S4RS3_REG_L0.390––
P5VS0_FET_RAMP0.720––
PCIE_CAMERA_D2R_C_N0.391––
PCIE_CAMERA_D2R_C_P0.390––
PCIE_CAMERA_R2D_N0.437––
PCIE_CAMERA_R2D_P0.437––
PDDR_S3_REG_L0.202––
PM_PWRBTN_L–3.400–
PP1V2_CAM0.272––
PP1V2_CAM_PCIE_PVDD_FLT0.348––
PP1V2_CAM_PCIE_VDD_FLT0.348––
PP1V2_CAM_XTALPCIEVDD0.319––
PP1V2_S30.202––
PP1V05_S0_REG_R0.072––
PP1V8_CAM0.473––
PP1V8_S3_REG_R0.344––
PP1V35_CAM0.265––
PP1V35_DDR_CLK0.265––
PP3V3_S00.3633.300–
PP3V3_S0_FAN0.3503.300–
PP3V3_S0SW_LCD0.537––
PP3V3_S0SW_LCD_UF0.537––
PP3V3_S0SW_SSD0.480––
PP3V3_S0SW_SSD_FLT0.480––
PP3V3_S3RS0_CAMERA0.3553.300–
PP3V3_S3RS0_CAMERA_R–3.300–
PP3V3_S4SW_SNS–3.300–
PP3V3_S5_REG_R0.330––
PP3V3_WLAN0.518––
PP3V3_WLAN_R0.518––
PP3V42_G3H0.2953.400–
PP5V_S00.4405.100–
PP5V_S3RS0_ALSCAM_F0.440––
PP5V_S4RS30.436––
PP18V5_DCIN_ISOL_ROL14.530–
PPBUS_G3H0.1148.520–
PPBUS_G3H_R0.1148.520–
PPBUS_S5_HS_COMPUTING_ISNS0.111––
PPDCIN_G3HOL14.600–
PPDCIN_G3H_CHGR0.62014.800–
PPDCIN_G3H_INRUSH0.62014.800–
PPDCIN_G3H_ISOLOL14.600–
PPDDR_S3_REG_R0.202––
PPHV_S0SW_LCDBKLT0.538––
PPVBAT_G3H_CHGR_REG0.1118.600–
PPVCC_S0_CPU_PH10.006––
PPVCC_S0_CPU_PH20.006––
PPVIN_G3H_P3V42G3H0.30614.280–
PPVIN_S0SW_LCDBKLT0.390––
PPVIN_S0SW_LCDBKLTFET0.131––
PPVIN_S4SW_TBTBST_FET0.468––
PPVMEMIO_S0_CPU0.202––
SMBUS_PCH_CLK0.495––
SMBUS_PCH_DATA0.496––
SMBUS_SMC_1_S0_SCL0.547––
SMBUS_SMC_1_S0_SDA0.517––
SMBUS_SMC_2_S3_SDA–3.300–
SMC_ADAPTER_EN–3.400–
SMC_BC_ACOK–3.400–
SMC_BIL_BUTTON_L–3.400–
SMC_CLK32K–1.700–
SMC_FAN_0_CTL0.737––
SMC_FAN_0_TACH0.7451.600–
SMC_PCH_SUSACK_L–3.300–
SMC_PM_G2_EN–3.400–
SMC_PME_S4_DARK_L–3.200–
SMC_RESET_L–3.300–
SMC_RX_L–3.400–
SMC_S5_PWRGD_VIN–3.300–
SMC_TX_L–3.400–
SMC_WAKE_L–3.100–
SYS_ONEWIRE–3.300–
TBTBST_BOOST0.468––
TBTBST_PWREN_DIV_L–8.150–
TP_CAM_PLL_BYPASS0.698––
UNCONNECTED_196OL––
UNCONNECTED_197OL––
UNCONNECTED_198OL––
UNCONNECTED_199OL––
USB_PWR_EN–3.300–

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00164?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00164: diode 0.114, voltage 8.520. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-00164?

OpenBoardData's known-good values for PP3V42_G3H on the 820-00164: diode 0.295, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S0 read on the 820-00164?

OpenBoardData's known-good values for PP3V3_S0 on the 820-00164: diode 0.363, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00164 board?

Open your own 820-00164 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License