Apple laptop board · OpenBoardData

820-00875 known-good readings

Known-good readings for the Apple laptop board 820-00875: 1,181 nets, including 82 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 76 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00875.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 82 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 20

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V3_G3H0.3323,300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail, judged from its G3H name (general naming convention, not a measurement). Known-good readings here: diode 0.332 to ground and 3,300 mV with power applied. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.332 suggests a short or leak on the rail; a missing or low voltage points to the rail not coming up. No known-good resistance reading is recorded for this rail.

PP3V3_G3H_UPC_XA0.333––
AI: what PP3V3_G3H_UPC_XA is and how to check it

PP3V3_G3H_UPC_XA is a 3.3 V always-on rail; the G3H part of the name indicates it is up whenever power is connected, and UPC suggests it feeds the USB-C side (both from the name, not from board data). The archive lists a known-good diode reading of 0.333 to ground, with no condition recorded and no known-good voltage reading here.

To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.333 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP3V3_G3H_UPC_XB0.334––
AI: what PP3V3_G3H_UPC_XB is and how to check it

PP3V3_G3H_UPC_XB is a 3.3 V always-on rail; the "G3H" part of the name indicates it is always on, and "UPC" suggests it feeds the USB-C side of the board. The archive lists one known-good diode reading of 0.334 to ground, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.334 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PP3V3_G3H_VR0.3333,300–
AI: what PP3V3_G3H_VR is and how to check it

PP3V3_G3H_VR is a 3.3 V rail; the G3H in the name indicates it is always-on (from the name), and VR suggests it comes from a regulator. Known-good readings here: diode 0.333 to ground and 3,300 (3.3 V) with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.333 usually points to a short or a faulty part on the rail; no known-good resistance reading is listed here, so compare against a matching net or a known-good board.

PPBUS_G3H0.41613.100–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this board; the G3H suffix, from the name, marks it as an always-on rail. Known-good readings in the archive are a diode value of 0.416 and 13.100 V with power applied. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode value far from 0.416 usually points to a short or a leaky part on the rail; no known-good resistance reading is listed here, so compare against a matching rail or a known-good board.

PPBUS_G3H_CPU0.41613.100–
AI: what PPBUS_G3H_CPU is and how to check it

PPBUS_G3H_CPU is the main power bus feeding the CPU section; the "G3H" part of the name indicates it's an always-on rail (from the name).

  • Known-good readings: diode 0.416 to ground, and 13.100 V with power applied. These come from community contributions and are a guide only.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage.
  • A diode reading far below 0.416 suggests a short or a leaky part on the rail; a voltage far from 13.100 V points to a supply or enable problem upstream.
  • No known-good resistance reading is available for this rail.
PPBUS_G3H_P3V3S50.4143.300–
AI: what PPBUS_G3H_P3V3S5 is and how to check it

PPBUS_G3H_P3V3S5 — reference note (820-00875)

  • From its name, this is a 3.3 V rail (P3V3S5) derived from PPBUS_G3H, and the G3H part means it is an always-on rail present whenever the board has power.
  • Known-good readings in the archive: diode 0.414 to ground, and 3.300 V with power applied. These are community readings and a guide only, not a guaranteed value.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode reading far below 0.414 suggests a short or a leaky part on the rail; a voltage well under 3.300 V with the rail enabled points to the rail not coming up or being loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.
PPBUS_G3H_P5VS40.41613,100–
PPBUS_G3H_R0.416––
AI: what PPBUS_G3H_R is and how to check it
  • PPBUS_G3H_R is the main battery/charger bus rail; the "G3H" in the name indicates it is always-on (from the name).
  • Known-good: diode-to-ground 0.416 (from the readings archive, a community guide; no condition given). No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.416 usually points to a short or a faulty component on that rail; a missing or wrong voltage under power points to the charging/PPBUS source. Confirm with a second measurement before replacing anything.
PPBUS_G3H_SPKRL0.41613.100–
AI: what PPBUS_G3H_SPKRL is and how to check it
  • PPBUS_G3H_SPKRL is a PPBUS rail, and the G3H in its name indicates it is always on. The SPKRL suffix suggests a branch feeding the speaker circuit (general naming convention, not from board data).
  • Known-good readings from the archive: diode 0.416 and voltage 13.100. These are community readings and only a guide.
  • To check it: power off, then measure diode mode from the rail to ground. Next, apply power and measure the voltage on the rail.
  • A diode reading far below 0.416 usually points to a short or a leaky part on the rail. A voltage well off 13.100 points to a supply or load problem. There is no known-good resistance reading for this rail.
PPBUS_G3H_SSD0.41613.100–
AI: what PPBUS_G3H_SSD is and how to check it

PPBUS_G3H_SSD (820-00875) — from the name, this is the main PPBUS rail feeding the SSD section; the "G3H" part indicates it is always-on once the charger and PPBUS are up.

  • Known-good readings in the archive: diode 0.416 to ground, voltage 13.100 V. These are community readings and only a guide; the data gives no condition for them.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.416 usually points to a short or a leaky part on the rail; a voltage well under 13.100 V with a normal diode reading points upstream, at PPBUS generation or an enable. No known-good resistance reading is available here, so compare against a matching rail or a known-good board before condemning a part.
PPBUS_G3H_TPAD0.41613.100–
AI: what PPBUS_G3H_TPAD is and how to check it

PPBUS_G3H_TPAD is the main PPBUS rail feeding the trackpad section; the G3H suffix, from the name, means it's always on whenever the board has power. Known-good readings in the archive: diode 0.416 and voltage 13.100 (no condition recorded). Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.416 usually points to a short or a leaky part on that rail; a missing or low voltage points to the rail not being enabled or supplied upstream. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board.

PPDCIN_G3H0.51520.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H — 820-00875

  • From the name, this is the DC-in rail: the adapter input that feeds the charger section, in the G3H (always-on) startup stage.
  • Known-good readings in the archive: diode 0.515 to ground, and 20.000 V with the adapter connected. These are community readings and a guide only.
  • Check it unpowered in diode mode from the rail to ground, then with the adapter connected measure the voltage on the rail.
  • A voltage well below 20 V with a normal diode reading points upstream, toward the adapter, input path or charger section; a diode reading far from 0.515 suggests a short or leaky part on the rail. No known-good resistance reading is recorded here.
PPDCIN_G3H_CHGR0.51520.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the always-on DC input rail feeding the charger section; the G3H part of the name indicates it is present whenever power is connected. The readings archive lists a diode value of 0.515 and a voltage of 20.000 for this rail, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare against 0.515; then apply power and check for about 20 V. A diode reading far below known-good usually suggests a short or leaky part on the rail, while a missing or low voltage points to the input supply, adapter or an open path upstream. No known-good resistance reading is recorded here.

PPDCIN_G3H_CHGR_R0.516––
AI: what PPDCIN_G3H_CHGR_R is and how to check it

PPDCIN_G3H_CHGR_R is the charger-side DC input rail; the "G3H" part of the name indicates it is always-on power. The only known-good figure here is a diode reading of 0.516 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the charger connected. No known-good voltage is recorded for this rail. A diode reading far from 0.516 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault.

PPDCIN_G3H_VSNS_IN0.515––
AI: what PPDCIN_G3H_VSNS_IN is and how to check it

PPDCIN_G3H_VSNS_IN is a DC-input sense line on the always-on G3H rail, judging from its name. The archive lists a diode reading of 0.515 to ground; no known-good voltage reading is recorded for this net. With the board unpowered, measure diode mode from the net to ground and compare with 0.515, then power up and check the voltage present. A diode reading far below that usually points to a short or leaky part on the net; far above can mean an open path.

PPVBAT_G3H_CHGR_R0.41613.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name indicates it is always on, and CHGR ties it to the charger circuit. Known-good readings in the archive are diode 0.416 and voltage 13.100. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.416 usually points to a short or a leaky part on that rail; a voltage well off 13.100 points to a charger or input problem. No known-good resistance reading is listed here.

PPVBAT_G3H_CHGR_REG0.41613.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side battery rail; the G3H in its name marks it as an always-on rail, and CHGR points to the charging circuit. Known-good readings in the archive: diode 0.416 and voltage 13.100 (no condition recorded). Check it with the board unpowered in diode mode to ground, then with power applied measure the voltage. A diode reading far from 0.416 usually points to a short or a leaky part on that rail; a voltage far from 13.100 points to the charger or its supply not coming up. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PPVBAT_G3H_CONN0.57113.100–
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail (the "G3H" always-on meaning is from the name). Known-good readings here are diode 0.571 and voltage 13.100; no resistance value is known. With the board unpowered, measure diode mode from the rail to ground and compare with 0.571, then apply power and check for about 13.100 V. A diode reading far off usually points to a short or leaky part on that rail, but one reading isn't proof, so confirm before replacing anything.

PPVIN_G3H_P3V3G3H0.522––
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H is an always-on rail, judging by the G3H in its name; it appears to be the input feed for the P3V3G3H always-on supply, though the parts on it aren't documented here.

  • Known-good diode reading: 0.522 to ground, board unpowered.
  • No known-good voltage reading here for this rail.
  • Check it with the board off in diode mode to ground, then power up and measure the voltage at the same point.
  • A diode reading far from 0.522 usually points to a short or a leaky part on the rail, but confirm with the powered voltage before replacing anything.

S5 and SUS: standby 21

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_S5_PCH_DCPDSW0.306––
AI: what PP1V_S5_PCH_DCPDSW is and how to check it
  • PP1V_S5_PCH_DCPDSW is a 1 V standby rail feeding the PCH's DCPDSW (display power domain switch) section, judged from the name; the S5/SUS part places it in the standby stage.
  • Known-good: diode to ground 0.306 (from the readings archive, a community guide, not a factory spec). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.306. Then power up and measure the voltage on the rail.
  • A diode reading far below 0.306 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with the voltage before replacing anything.
PP1V_S5G0,0551.000–
PP1V_S5G_PCHCLK0.055––
AI: what PP1V_S5G_PCHCLK is and how to check it
  • What it is: A 1 V standby rail feeding the PCH clock section, judged from the name (S5/SUS = standby, PCHCLK = PCH clock). The parts on the net aren't documented here.
  • Known-good reading: diode 0.055 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power on and measure the rail voltage.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a missing voltage points to the standby supply or enable side. Confirm with a second measurement before replacing anything.
PP1V_S5G_REG0.0551.000–
AI: what PP1V_S5G_REG is and how to check it

PP1V_S5G_REG is a 1 V standby rail; the S5/SUS in the name (from the name) marks it as a standby-stage supply, present before the board fully powers on. The archived readings for this net are diode 0.055 and voltage 1.000, with no condition noted, so treat them as a guide only.

  • Check it unpowered: diode mode from the net to ground, board off and unplugged, and compare with 0.055.
  • Then power the board and measure the voltage, expecting about 1.000 V.
  • A diode reading far below known-good suggests a short or a leaky part on the rail; a voltage well off 1.000 V points to the rail not coming up or being loaded down. No known-good resistance reading exists for this net, so compare against a matching rail or a known-good board before condemning anything.
PP1V_S5GTD0,0501,000–
PP1V_SUS_PCH_VCCCLK2_F0,0551,000–
PP1V_SUS_PCH_VCCCLK4_F0,0551,000–
AI: what PP1V_SUS_PCH_VCCCLK4_F is and how to check it

PP1V_SUS_PCH_VCCCLK4_F is a standby (S5/SUS) rail, judging from its name — a 1 V supply for the PCH clock section. Known-good readings here are a diode value of 0,055 and 1,000 V, with no condition recorded, so treat them as a guide only.

  • Check it unpowered: diode mode from the rail to ground, then confirm the 1 V with power applied.
  • A diode reading far below 0,055 suggests a short or leaky load on the rail; a missing or low voltage with power on points to the supply or its enable.
  • No known-good resistance reading is available for this rail, so compare against a matching rail or a known-good board.
PP1V_SUS_PCH_VCCCLK5_F0,0551,000–
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it

PP1V_SUS_PCH_VCCCLK5_F — reference note

  • From its name, this is a 1 V standby rail feeding the PCH clock section (SUS/S5 = standby), so it should be present before the board fully powers on.
  • Known-good readings from the archive: diode mode to ground 0,055 and voltage 1,000 V. These are community readings and only a guide; no known-good resistance reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage on the same point.
  • A diode reading far from 0,055 usually points to a short or a leaky part on that rail; a correct diode reading with no or wrong voltage points upstream, at the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP1V_SUSRS0SW_PCHCLK0.046––
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0,0501,000–
PP1V2_S5_SMC_VDDC0.485––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC is a 1.2 V standby rail feeding the SMC (system management controller) domain; the S5/SUS part of the name indicates it comes up in the standby stage. The only known-good figure here is a diode reading of 0.485 to ground, with no condition noted and no known-good voltage on record. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.485 suggests a short or a leaky load on the rail; a voltage that never appears points to the standby supply or its enable not coming up. These readings are community-sourced guides and vary with board state, so treat a small difference as normal and confirm before replacing anything.

PP1V8_S5G0.2001,800–
AI: what PP1V8_S5G is and how to check it
  • PP1V8_S5G is a 1.8 V standby rail; the "S5" and "SUS" in the name indicate standby state (from the name).
  • Known-good readings: diode 0.200 to ground, voltage 1,800 (1.8 V). These are community readings and a guide only.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far from 0.200 suggests a short or leaky load on the rail; a voltage far from 1.8 V points to the rail not coming up or being loaded down. No known-good resistance reading is available here.
PP1V8_SUS_PCH_VCC1P8OL––
AI: what PP1V8_SUS_PCH_VCC1P8 is and how to check it

PP1V8_SUS_PCH_VCC1P8 is a 1.8 V standby rail feeding the PCH, judging by its name (PP = power rail, 1V8 = 1.8 V, SUS = suspend/standby). The only known-good reading recorded is a diode value of OL to ground, with the board unpowered. Check it in diode mode from the rail to ground with power off, then measure the voltage with the board powered in standby; no known-good voltage reading exists here, so compare against a matching 1.8 V standby rail or a known-good board. A diode reading far from OL (a low value) usually points to a short or leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V0_S5_AVREF_SMC0.642––
AI: what PP3V0_S5_AVREF_SMC is and how to check it

PP3V0_S5_AVREF_SMC is a 3.0 V standby rail (the 3V0 and S5 parts come from the name), likely an analog reference for the SMC; that function is general interpretation, not from the board data. Known-good: diode 0.642 to ground, with no condition recorded and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.642 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare with a matching net or a known-good board before replacing anything.

PP3V3_S50.3153.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage. In the readings archive it shows a diode reading of 0.315 and a voltage of 3.300, which are community-contributed guides rather than guaranteed values. To check it, power the board off and measure diode mode from PP3V3_S5 to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.315 usually points to a short or a damaged component on that rail, while a missing or low voltage suggests the standby supply isn't coming up. No known-good resistance reading is listed for this rail.

PP3V3_S5_S0R0.313––
AI: what PP3V3_S5_S0R is and how to check it

PP3V3_S5_S0R is a 3.3 V rail; the S5/SUS part of the name (from the name) puts it in the standby stage, and the S0R suffix suggests it also feeds something kept alive into run state. The archive's only known-good figure is a diode reading of 0.313 to ground, with no condition recorded; there is no known-good voltage or resistance value here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.313 usually points to a short or a damaged load on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S5_SSD_SNS0.3153.300–
AI: what PP3V3_S5_SSD_SNS is and how to check it

PP3V3_S5_SSD_SNS is a 3.3 V standby rail feeding SSD sense circuitry, judging from its name (S5/SUS = standby stage). Known-good readings here: diode 0.315 to ground, and 3.300 V with power applied. Check it by powering off and measuring diode mode from the net to ground, then powering up and measuring the voltage. A diode reading far below 0.315 suggests a short or leaky part on the rail; a voltage well under 3.300 V points to the rail not coming up or being loaded down. No known-good resistance reading is recorded here.

PP3V3_S5_TBT_X_SW0.425––
AI: what PP3V3_S5_TBT_X_SW is and how to check it
  • PP3V3_S5_TBT_X_SW is a 3.3 V rail; the "S5" in the name marks it as a standby-stage rail, and "TBT" suggests it belongs to the Thunderbolt side (both from the name).
  • Known-good from the archive: diode 0.425 to ground, no condition recorded. No known-good voltage reading here.
  • Check it unpowered in diode mode, red lead to ground, black to the rail, then measure the voltage with power applied.
  • A diode reading far from 0.425 usually points to a short or a leaky part on that rail, but one reading isn't proof; compare with a matching rail before replacing anything.
PP3V3_S5G0.303––
AI: what PP3V3_S5G is and how to check it

PP3V3_S5G is a 3.3 V standby rail; the "S5" and "SUS" in its name indicate it belongs to the standby stage, so it should be present before the board fully powers on. The only known-good reading here is a diode value of 0.303 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage on the rail. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far below 0.303 suggests a short or a leaky part on the rail; far above it suggests an open connection.

PP5V_S50.3975.000–
AI: what PP5V_S5 is and how to check it
  • PP5V_S5 is the 5 V standby rail; the "S5" in the name marks it as a standby-stage supply (general naming, not from board data).
  • Known-good reading here: diode 0.397 to ground, voltage 5.000 V. These come from community readings and are a guide only.
  • Check with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage.
  • A diode value far from 0.397 suggests a short or leaky load on the rail; a voltage well off 5.000 V points to the standby supply or its enable not coming up. No known-good resistance reading is recorded here.
PPVCCPCH_S5G0.0351.000–
AI: what PPVCCPCH_S5G is and how to check it
  • What it is: PPVCCPCH_S5G is a power rail; the "S5" and "SUS" in the name indicate it belongs to the standby/suspend domain, so it should be present in standby. That reading is from the name, not from board data.
  • Known-good readings: diode 0.035 and voltage 1.000, from the readings archive. These are community contributions and only a guide.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.035 suggests a short or leaky load on the rail; a voltage far from 1.000 with a normal diode reading points to the rail not being enabled or its source missing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

S4 5

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.4133.300–
AI: what PP3V3_S4 is and how to check it
  • PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it.
  • Known-good readings here: diode 0.413 to ground, voltage 3.300 with power applied. These come from community contributions and are a guide, not a guarantee.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage.
  • A diode reading far from 0.413 usually points to a short or a leaky load on the rail; a voltage well off 3.300 points to the rail not coming up or being loaded down. No known-good resistance reading exists here, so compare against a matching net or a known-good board.
PP3V3_S4_WLS0.4133.300–
AI: what PP3V3_S4_WLS is and how to check it

PP3V3_S4_WLS is a 3.3 V rail; the "S4" in its name marks it as a startup-stage rail, and "WLS" suggests it feeds the wireless section (that part is from the name, not from board data). Known-good readings here are diode 0.413 and voltage 3.300, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.413 usually points to a short or a leaky load on the rail; a voltage well below 3.300 with a normal diode reading points to the rail not being enabled or its supply missing. No known-good resistance reading is available for this rail.

PP5V_S40.4075.000–
AI: what PP5V_S4 is and how to check it
  • PP5V_S4 is a 5 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.407 to ground, voltage 5.000 with power applied. No known-good resistance reading here.
  • Check with the board unpowered: multimeter in diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.407 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with voltage under power before replacing anything.
PP5V_S4_TPAD_CONN0.406––
AI: what PP5V_S4_TPAD_CONN is and how to check it

PP5V_S4_TPAD_CONN — from the name, a 5 V rail feeding the trackpad connector, enabled at the S4 power stage (general naming convention, not from this board's data).

  • Known-good: diode reading to ground 0.406. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage at the connector.
  • A diode reading far below 0.406 usually points to a short or a leaky part on that rail; a much higher or open reading points to a broken trace or missing connection. Confirm with the voltage before replacing anything.
PPVIN_S4_TPAD_FUSE0.41613.100–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE is a trackpad input rail at the S4 startup stage, judging from its name. Known-good readings: diode 0.416 to ground and 13.100 V with power applied.

  • With the board unpowered, measure diode mode from the rail to ground; 0.416 is the guide.
  • With power applied, measure the voltage; 13.100 V is the guide.
  • A diode reading far below 0.416 suggests a short or leaky part on the rail; a voltage well under 13.100 V suggests the rail isn't being fed or is loaded down.

No known-good resistance reading here. These are community readings and vary with board state, so treat them as a guide, not a pass/fail limit.

S3: memory 5

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFDQ_A0.385––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it
  • What it is: From its name, PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail that comes up at the S3 (memory) stage of startup. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.385 in diode mode to ground, board unpowered. That's a community guide, not a factory spec, and the data gives no known-good voltage for this rail.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.385; then power on and measure the DC voltage, expecting roughly 0.6 V from the name.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail, and a missing or wrong voltage points to the rail not being enabled or its source not switching. Confirm with a second measurement before replacing anything.
PP1V_S30.095––
AI: what PP1V_S3 is and how to check it

PP1V_S3 is a memory-stage rail (S3), judging by its name. The archive lists one known-good diode reading of 0.095 to ground; no known-good voltage or resistance reading is recorded here. With the board unpowered, measure diode mode from PP1V_S3 to ground and compare with 0.095, then power up and check the rail voltage. A diode reading far below known-good usually points to a shorted load on the rail; a far higher one can mean an open path. Readings vary with board state, so treat them as a guide, not a verdict.

PP1V2_S30.1301.200–
AI: what PP1V2_S3 is and how to check it
  • What it is: PP1V2_S3 is a 1.2 V rail; the "S3" suffix (from the name) places it in the memory stage of the startup sequence. The board data has no parts list, so which components sit on it isn't known.
  • Known-good readings: diode 0.130 and voltage 1.200, from the community archive and a guide only, not a guarantee.
  • How to check: with the board unpowered, diode mode from PP1V2_S3 to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail, and a missing or low voltage points to the rail not being enabled or its supply failing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP1V2_S3_REG0.1301.200–
AI: what PP1V2_S3_REG is and how to check it

PP1V2_S3_REG is a 1.2 V rail; the S3 in the name marks it as a memory-stage rail, and the 1V2 matches the 1.200 V nominal. Known-good from the readings archive: diode 0.130 to ground and 1.200 V with power applied (no condition recorded). Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.130 usually points to a short or leaky load on the rail; a low or missing voltage points to the rail not coming up or being loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP1V8_S30.144––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix suggests it belongs to the memory stage of startup, based on the name. The archive lists a diode reading of 0.144 to ground for this rail, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far from 0.144 usually points to a short or a faulty part on that rail, but confirm with more measurements before replacing anything.

S0: running 31

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V_OPC_S00.1151.000–
AI: what PP1V_OPC_S0 is and how to check it

PP1V_OPC_S0 is a 1 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "OPC" is just the rail's label. Known-good readings for this rail are a diode value of 0.115 and a voltage of 1.000. To check it, power the board off and measure diode mode from PP1V_OPC_S0 to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.115 usually points to a short or a leaky part on that rail; a voltage well off 1.000 with a normal diode reading points more to the rail not being enabled or its source not coming up. No known-good resistance reading is available here, so compare against a matching rail or a known-good board if needed.

PP1V_S0G0.083––
AI: what PP1V_S0G is and how to check it
  • PP1V_S0G is a 1 V rail. From the name, the S0 suffix means it belongs to the running (S0) state, so it should be present once the board is powered on, not in standby.
  • Known-good reading in the archive: diode mode to ground 0.083. That is a community figure and a guide only; no known-good voltage reading is recorded here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode reading far from 0.083 usually points to a short or a leaky load on the rail, but confirm with a second measurement before suspecting a part.
PP1V_S0SW_PCHCLKOL––
AI: what PP1V_S0SW_PCHCLK is and how to check it

PP1V_S0SW_PCHCLK (820-00875) — from the name, this is a 1 V rail in the S0 (running) state, switched (SW), feeding the PCH clock circuit. The only archived reading is diode mode to ground: OL (open, no conduction to ground). No known-good voltage reading is recorded here.

  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Compare with the archived OL.
  • Then power the board and measure the voltage on the rail; there is no known-good voltage value here to compare against, so use a matching rail or a known-good board.
  • An OL in diode mode is a guide, not proof of a fault; a reading far from OL (a low diode drop) usually points to a short or a leaky part on the rail.
PP1V2_S0G0.038––
AI: what PP1V2_S0G is and how to check it

PP1V2_S0G is a 1.2 V rail; the "S0" in its name marks it as a running-state supply, so it should be present once the board is fully on. The archive lists one known-good diode reading for it: 0.038 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is recorded here, so compare against a known-good board or the rail's expected 1.2 V. A diode reading far from 0.038 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V8_S00.309––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail; the "S0" in its name indicates it belongs to the running (S0) power state. The readings archive lists one known-good value for this board: diode 0.309, with no condition noted.

To check it, power the board off and measure diode mode from PP1V8_S0 to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.309 usually points to a short or a leaky part on that rail; a voltage far off 1.8 V points to the rail not coming up or being loaded down. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PP3V3_S00.317––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, judging by its name; it should come up once the board is fully on. The only known-good figure here is a diode reading of 0.317 to ground, with no condition noted. Check it unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far from 0.317 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S0_CPUTHMSNS_R0.336––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R (820-00875) — reference note

  • From the name, this is a 3.3 V rail that is up in the S0 (running) state, and the "CPUTHMSNS" part suggests it feeds CPU thermal sensing. That reading of the name is general, not from board data.
  • Known-good: diode 0.336 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.336 usually points to a short or a leaky part on that net; confirm with a second measurement before replacing anything.
PP3V3_S0SW_LCD0.511––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a 3.3 V LCD-switched rail; the "S0" in the name marks it as a running-state rail, and "SW" suggests it is switched on rather than always present. The only known-good figure here is a diode reading of 0.511 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from 0.511 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP3V3_TBT_X_S00.3173,300–
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "TBT" suggests it serves the Thunderbolt side of the board (from the name only). Known-good readings in the archive: diode 0.317 to ground and 3,300 (3.3 V) with the board powered. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.317 usually points to a short or a leaky part on that rail; a missing or low voltage with a normal diode reading points more toward the rail not being enabled or its source not coming up. No known-good resistance reading is recorded here, and these are community figures, so treat them as a guide.

PP5V_S00.416––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, judging from its name; the archive has no board file, so the parts on it aren't known.

  • Known-good: diode 0.416 to ground (no condition recorded). No known-good voltage reading here.
  • Check: power off, diode mode from PP5V_S0 to ground; then power on and measure the voltage in the running state.
  • A diode reading far below 0.416 usually suggests a short or a leaky load on the rail; a far higher one can mean an open path. Confirm with a voltage measurement before replacing anything.
PP5V_S0_ALSCAM_F0.413––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds the front camera circuit. The only known-good figure here is a diode reading of 0.413 to ground; there is no known-good voltage reading in this data.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.413.
  • Then power the board and measure the voltage on the rail; the data gives no expected value, so compare against a known-good board or the same rail on a matching circuit.
  • A diode reading far below 0.413 suggests a short or leaky part on the rail; a much higher or open reading points to a broken connection or missing component.
  • A correct diode reading with no voltage at S0 points upstream, to the enable or supply that feeds this rail, rather than to the rail itself.
PP5V_S0_BKLT_A0.416––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the backlight (BKLT) 5 V rail that comes up in the S0 running state, judging from the name. The only known-good reading here is a diode value of 0.416 to ground; there is no known-good voltage reading for this rail. With the board unpowered, measure diode mode from PP5V_S0_BKLT_A to ground and compare with 0.416. Then power the board and check the voltage on the rail. A diode reading far below 0.416 usually points to a short or a leaky part on the rail, while a much higher reading can mean an open connection; a single reading isn't proof, so confirm before replacing anything.

PP5V_S0_BKLT_D0.417––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the 5 V backlight rail that is present in the S0 (running) state, from its name. The archive lists one known-good reading: diode 0.417, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage, which should be about 5 V. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.417 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.

PP5V_S0_P1VOPC0.418––
AI: what PP5V_S0_P1VOPC is and how to check it

PP5V_S0_P1VOPC is a 5 V rail, from its name: the "S0" part means it belongs to the running state, and "P1VOPC" is the load it feeds. The archive lists one known-good diode reading of 0.418 to ground; there is no known-good voltage reading for this rail here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S0. A diode reading far from 0.418 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S0SW_LCD0.513––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is the switched 5 V rail feeding the LCD section, active in the S0 (running) state — that's from the rail's name. The only known-good reading here is a diode value of 0.513 to ground, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.513 suggests a short or leaky load on the rail; far above it can mean an open path. No known-good voltage value is available, so compare against a matching rail on a known-good board.

PPVCCCPU_S0G0.0011.800–
AI: what PPVCCCPU_S0G is and how to check it

PPVCCCPU_S0G is the CPU core power rail; the S0 in its name indicates it is up in the running state. Known-good readings here are diode 0.001 to ground and 1.800 V with power applied. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from 0.001 in diode mode usually points to a short or open on the rail, but one reading alone doesn't confirm a bad part. No known-good resistance reading is available here.

PPVCCCPU_S0G_PH10.0011.800–
AI: what PPVCCCPU_S0G_PH1 is and how to check it

PPVCCCPU_S0G_PH1 is a CPU power rail (VCCCPU) in the running state (S0), from its name; the PH1 suffix usually marks a phase of the CPU buck converter, which is general naming, not from this board's data. Known-good readings here: diode 0.001 to ground, voltage 1.800. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.001 suggests a short or leaky part on the rail; a voltage far from 1.800 points to the CPU supply not regulating. No known-good resistance value is listed for this rail.

PPVCCCPU_S0G_PH20.0011.800–
AI: what PPVCCCPU_S0G_PH2 is and how to check it
  • PPVCCCPU_S0G_PH2 is a CPU power rail: "PPVCCCPU" is the CPU core supply, "S0G" means it's up in the running (S0) state, and "PH2" is a phase of the CPU buck converter — all from the name, not from board data.
  • Known-good readings here: diode 0.001 and voltage 1.800 V. These come from the community archive and are a guide only; no known-good resistance is listed.
  • To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage on the rail.
  • A diode reading far above 0.001 suggests an open phase or a broken connection; a voltage far from 1.800 V under load points to the CPU supply not regulating — confirm with the enable and feedback signals before suspecting a part.
PPVCCGT_S0G0.0001.800–
AI: what PPVCCGT_S0G is and how to check it

PPVCCGT_S0G is a running-state (S0, from the name) supply rail, likely the graphics core (VCCGT) voltage. The archive gives diode 0.000 and voltage 1.800 for it; treat these as a community guide, and note the 0.000 diode reading is unusual for a live rail and may reflect a shorted or low-impedance path. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 1.800 or a diode reading well off 0.000 points to a fault on that rail or its load, but one reading alone doesn't confirm a bad part. No known-good resistance value is recorded here.

PPVCCGT_S0G_PH10.0001.8002.000R
AI: what PPVCCGT_S0G_PH1 is and how to check it
  • What it is: PPVCCGT_S0G_PH1 is a power rail; the "S0" in its name indicates it is a running-state rail, and "VCCGT" points to the graphics/GT core supply (from the name).
  • Known-good readings (archive, guide only): diode 0.000, voltage 1.800, resistance 2.000R. The very low diode and resistance values are notable and may reflect a low-ohms inductor/switching node rather than a fault; treat them as a guide, not a pass/fail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then apply power and measure the voltage at the rail.
  • If far off: a missing or wrong voltage points to the rail's supply circuit or its enable/feedback path rather than the load; a shorted diode/resistance reading points to a shorted component on the rail. No known-good reading of another kind is listed here, so compare against a matching rail or a known-good board before condemning a part.
PPVCCGT_S0G_PH20.0001.8002.000R
AI: what PPVCCGT_S0G_PH2 is and how to check it

PPVCCGT_S0G_PH2 is a running-state (S0, from the name) power rail, likely a graphics/processor supply phase, though the exact parts on it aren't documented here. Known-good readings from the archive: diode 0.000, voltage 1.800 V, resistance 2.000R. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A diode or resistance far above these values points to an open or missing load; a voltage well off 1.800 V points to the rail not regulating. These are community readings and only a guide, and no known-good waveform or current reading exists here.

PPVCCGT_S0G_PH30.0001.8002.000R
AI: what PPVCCGT_S0G_PH3 is and how to check it

PPVCCGT_S0G_PH3 is a running-state (S0, from the name) power rail, likely a CPU graphics core supply (general interpretation, not from board data). Archived readings for it: diode 0.000, voltage 1.800, resistance 2.000R — treat these as a guide only, and note that a 0.000 diode reading to ground is very low and can be normal on a heavy low-voltage rail.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running.
  • A voltage far from 1.800 or a resistance far from 2.000R usually points to a short or a failed supply on that rail; a low diode reading alone is not proof of a bad part.
  • No known-good values of other kinds are listed here, so compare against a matching rail on a known-good board where possible.
PPVCCIO_S0G0.0750.950–
AI: what PPVCCIO_S0G is and how to check it

PPVCCIO_S0G is a running-stage supply rail (the S0 suffix is from the name, meaning the board is fully on); the VCCIO part usually indicates an I/O supply, which is general naming, not from this board's data. Known-good readings here are diode 0.075 and voltage 0.950, with no condition recorded, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.075 suggests a short or leaky load on the rail; a voltage well off 0.950 points to the rail not coming up or being pulled down. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PPVCCOPC_S0G0.010––
AI: what PPVCCOPC_S0G is and how to check it
  • What it is: From its name, PPVCCOPC_S0G is a VCCOPC power rail, and the S0G suffix places it in the running stage. The board data doesn't list which parts sit on it.
  • Known-good: diode reading 0.010 to ground, with no condition given. No known-good voltage reading here.
  • How to check: Power off and measure diode mode from the rail to ground, then measure the voltage with the board powered.
  • If it's far off: A diode reading well below 0.010 suggests a short or a low-impedance load on the rail; confirm with a second point and inspect for a shorted part before replacing anything.
PPVCCSA_S0G0.0021.500–
AI: what PPVCCSA_S0G is and how to check it

PPVCCSA_S0G is a supply rail; the S0 suffix in its name indicates it is a running-state rail (general naming convention, not from board data). Known-good readings here are diode 0.002 and voltage 1.500. Check it unpowered in diode mode to ground, then measure the voltage with the board powered. A reading far from known-good usually points to a short or a missing supply on that rail, though a single reading isn't proof a part is bad.

PPVCCSA_S0G_R0.0021.500–
AI: what PPVCCSA_S0G_R is and how to check it

PPVCCSA_S0G_R is a running-state (S0, from the name) supply rail, likely a small always-on-domain voltage for the SoC's SA section — that's general interpretation, not from board data. Known-good readings here: diode 0.002 to ground and 1.500 V with power applied; no resistance value is recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode reading far above 0.002 suggests an open trace or missing part rather than a short; a voltage well off 1.500 V points to the rail's regulator or its enable. These are community readings and only a guide.

PPVIN_S0SW_LCDBKLT0.82012.900–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT is the input supply for the LCD backlight switch, active in the S0 (running) state. It's a power rail, not a signal.
  • Known-good readings (community guide): diode 0.820 to ground, and 12.900 V with the board powered in S0. No known-good resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage in S0.
  • If it's far off: A diode reading well below 0.820 suggests a short or leaky load on the rail; no voltage where 12.900 V is expected points to the supply or enable for the backlight circuit being missing. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT_F0.41613.100–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F is the LCD backlight input rail; the S0 in the name (from the name) marks it as a running-state rail, and LCDBKLT points to the backlight circuit. Known-good readings here are diode 0.416 and voltage 13.100, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.416 usually points to a short or a faulty component on that rail; a voltage far from 13.100 points to a supply or enable problem upstream. These are community readings and only a guide, and no known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT_R0.41613.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail on this 820-00875, a running-state (S0) supply, judging by its name. The archive lists a known-good diode reading of 0.416 and a voltage of 13.100; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.416 usually points to a short or leaky load on the rail, while a missing or low voltage with a normal diode reading points upstream to the supply that feeds it. No known-good resistance reading is recorded here.

PPVOUT_S0_LCDBKLT1.11755.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT — 820-00875

  • From the name: the LCD backlight boost output rail, enabled in the S0 (running) state. "PPVOUT" is a positive output rail; "LCDBKLT" is the panel backlight.
  • Known-good readings in the archive: diode mode to ground 1.117, and 55.000 V with power applied. These are community readings and vary with board state, so treat them as a guide.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage, ideally at the backlight connector or a test point on the rail.
  • A diode reading far below 1.117 suggests a short or leaky load on the rail; a voltage far from 55.000 V with the board running points at the backlight boost circuit or its enable, not necessarily the panel. No known-good resistance reading is available here, so compare against a matching rail on a known-good board if needed.
PPVTT_S00.070––
AI: what PPVTT_S0 is and how to check it

PPVTT_S0 is a running-state (S0, from the name) rail; the "VTT" part suggests it's a termination/ddr-style rail, though that's general interpretation, not from this board's data. Known-good: diode 0.070 to ground, no voltage reading recorded here. With the board unpowered, measure diode mode from PPVTT_S0 to ground and compare with 0.070; then power up and check the rail voltage against its expected level (no known-good voltage here, so compare with a known-good board). A diode reading far from 0.070 usually points to a short or leaky part on the rail, but one reading alone doesn't confirm a fault.

Every net with a reading

NetDiodeVoltageResistance
8409_ASP1_LRCLK_R0.475––
8409_ASP1_SCLK_R0.470––
8409_ASP1_SDOUT_R0.314––
8409_ASP2_LRCLK_R0.515––
8409_ASP2_SCLK_R0.475––
8409_ASP2_SDOUT_R0.466––
8409_DMIC1_CLK_R0.550––
8409_DMIC1_DATA0.545––
8409_HDA_SDIN0_R0.450––
8409_I2C_SCL0.450––
8409_I2C_SDA0.460––
8409_SPKR_ID00.699––
ACT_THERM_TRIP_L0.709––
ADDR_FL0.338––
AGND_P3V3G3H0.000––
AGND_U75100.000––
AGND_U75200.000––
AGND_U75300.000––
ALERT_L0.117––
ALL_SYS_PWRGD0.419––
AMP_FL_LRCLK0.473––
AMP_FL_SCLK0.484––
AMP_FL_SDOUT0.311––
AMP_RL_LRCLK0.473––
AMP_RL_SCLK0.484––
AMP_RL_SDOUT0.311––
AP_CLKREQ_L0.442––
AP_DEV_WAKE0.460––
AP_PCIE_WAKE_L0.448––
AP_RESET_L0.466––
AP_S0IX_WAKE_L0.540––
AP_S0IX_WAKE_SEL0.553––
AUD_ASP1A_LRCLK0.473––
AUD_ASP1A_SCLK0.471––
AUD_ASP1A_SDOUT0.311––
AUD_ASP1B_LRCLK0.475––
AUD_ASP2_SDIN0.520––
AUD_I2C_SCL0.443––
AUD_I2C_SDA0.465––
BANJO_DRVHVR10.507––
BANJO_DRVHVR1_R0.503––
BANJO_DRVHVR30.474––
BANJO_DRVHVR3_R0.473––
BANJO_DRVHVR40.494––
BANJO_DRVHVR4_R0.494––
BANJO_DRVHVR50.494––
BANJO_DRVHVR5_R0.490––
BANJO_DRVLVR10.432––
BANJO_DRVLVR1_R0.433––
BANJO_DRVLVR30.435––
BANJO_DRVLVR40.433––
BANJO_DRVLVR4_R0.433––
BANJO_DRVLVR50.436––
BANJO_DRVLVR5_R0.435––
BANJO_ENVR10.400––
BANJO_ENVR20.413––
BANJO_ENVR30.422––
BANJO_ENVR40.412––
BANJO_ENVR50.407––
BANJO_FBLDO10.074––
BANJO_FBLDO1_R0.070––
BANJO_FBVR1_N0.000––
BANJO_FBVR1_P0.054––
BANJO_FBVR1P0.050––
BANJO_FBVR2_P0.238––
BANJO_FBVR2R_N0.037––
BANJO_FBVR2R_P0.242––
BANJO_FBVR3RP0.015––
BANJO_FBVR4_N0.000––
BANJO_FBVR4_P0.042––
BANJO_FBVR4P0.038––
BANJO_FBVR5_N0.000––
BANJO_FBVR5_P0.037––
BANJO_FBVR5P0.034––
BANJO_ILIMVR10.427––
BANJO_ILIMVR3LS0.427––
BANJO_ILIMVR40.432––
BANJO_ILIMVR5LS0.428––
BANJO_PGNDVR10.000––
BANJO_PGNDVR30.000––
BANJO_PGNDVR40.000––
BANJO_PGNDVR50.000––
BANJO_SWVR10.0551.000–
BANJO_SWVR1_SNUBOL––
BANJO_SWVR1R0.054––
BANJO_SWVR20.2001,800–
BANJO_SWVR30.0750.950–
BANJO_SWVR40.1301.200–
BANJO_SWVR4_SNUBOL––
BANJO_SWVR4R0.040––
BANJO_SWVR50.0351.000–
BANJO_SWVR5_SNUBOL––
BANJO_SWVR5R0.037––
BANJO_VINLDO1S0.037––
BKLT_PWM_KEYB0.494––
BKLT_SCL0.488––
BKLT_SD0.547––
BKLT_SENSE_OUT0.682––
BT_DEV_WAKE0.560––
BT_GPIO40.676––
BT_LOW_PWR_L0.464––
BT_PWRRST_L0.470––
BT_SPI_CLK0.660––
BT_SPI_CS_L0.627––
BT_SPI_MISO0.515––
BT_SPI_MOSI0.520––
BT_TIMESTAMP0.475––
BT_UART_CTS_L0.403––
BT_UART_D2R0.381––
BT_UART_R2D0.403––
BT_UART_RTS_L0.380––
BTROM_HOLD_L0.685––
BTROM_WP_L0.685––
BUF_EDP_PANEL_PWR_EN0.560––
BUF_SMC_RESET_L0.621––
CAM_DEBUG_RESET_L0.641––
CAM_PWR_SEL0.789––
CAM_SENSOR_WAKE_L0.774––
CAM_TEST_MODE0.485––
CAM_TEST_OUT0.793––
CAM_UARTCTS0.510––
CAM_UARTRXD0.485––
CAM_XTAL_FREQ0.503––
CAM_XTAL_SEL0.505––
CAMERA_CLKREQ_L0.525––
CAMERA_PWR_EN0.482––
CAMERA_PWR_EN_PCH0.482––
CAMERA_RESET_L0.440––
CATERR_LEDOL––
CATERR_LED_LOL––
CHGR_AMON0.549––
CHGR_BMON0.549––
CLK25M_CAM_CLKN0.747––
CPU_CATERR_L0.114––
CPU_CFG_RCOMP0.018––
CPU_CFG<0>0.249––
CPU_CFG<1>0.248––
CPU_CFG<2>0.248––
CPU_CFG<3>0.248––
CPU_CFG<4>0.215––
CPU_CFG<5>0.250––
CPU_CFG<7>0.248––
CPU_CFG<8>0.247––
CPU_CFG<9>0.248––
CPU_CFG<10>0.247––
CPU_CFG<11>0.250––
CPU_CFG<12>0.249––
CPU_CFG<13>0.248––
CPU_CFG<15>0.249––
CPU_CFG<16>0.249––
CPU_CFG<17>0.250––
CPU_CFG<18>0.249––
CPU_CFG<19>0.248––
CPU_DIMM_VREFCA0.358––
CPU_DIMMA_VREFDQ0.387––
CPU_DIMMB_VREFDQ0.384––
CPU_PECI0.132––
CPU_PECI_R0.117––
CPU_PROCHOT_L0.280––
CPU_RSVD_AK130.285––
CPU_VCCGTSENSE_P0.001––
CPU_VCCIOSENSE_N0.000––
CPU_VCCIOSENSE_P0.012––
CPU_VCCSASENSE_N0.000––
CPU_VCCSASENSE_P0.002––
CPU_VCCSENSE_N0.000––
CPU_VCCSENSE_P0.001––
CPU_VCCST_PWRGD0.327––
CPU_VIDALERT_L0.114––
CPU_VIDSCLK_R0.110––
CPU_VIDSOUT0.111––
CPU_ZVM_L0.261––
CPUHI_IOUT0.610––
CPUTHMSNS_ADDR_SEL0.037––
CPUTHMSNS_ALERT_L0.532––
CPUTHMSNS_D1_N0.550––
CPUTHMSNS_D1_P0.545––
CPUVR_COMP0.572––
CPUVR_COMP_R1.510––
CPUVR_FB0.445––
CPUVR_FB_R_10.596––
CPUVR_FB_R_20.700––
CPUVR_FB_R_30.001––
CPUVR_FCCM0.558––
CPUVR_IMON0.571––
CPUVR_ISEN10.572––
CPUVR_ISEN20.572––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS_R_NOL––
CPUVR_ISNS_R_POL––
CPUVR_ISNS1_N0.0011.800–
CPUVR_ISNS1_P0.0011.800–
CPUVR_ISNS2_N0.0011.800–
CPUVR_ISNS2_P0.0011.800–
CPUVR_ISUM_IOUTOL––
CPUVR_ISUM_N0.001––
CPUVR_ISUM_P0.177––
CPUVR_ISUMN_R0.084––
CPUVR_NTC0.573––
CPUVR_NTC_LOL––
CPUVR_PHASE20.001––
CPUVR_PWM10.558––
CPUVR_PWM20.558––
CPUVR_RTN0.000––
CPUVR_SNB1OL––
CPUVR_SW10.0011.800–
CPUVR_SW20.0011.800–
CPUVR_VCC0.408––
CPUVR_VIN0.422––
CPUVSENSE_IN0.001––
CS8409_VA_PLL0.520––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.453––
DIAG_LED_ENABLE_LOL––
DIV_PPBUS_G3HOL––
DIV_PPDCINOL––
DMIC1_CLK0.560––
DMIC1_DATA0.544––
DP_INT_HPD0.471––
DP_X_SNK_RBIAS0.742––
DP_X_SNK0_AUXCH_C_N0.183––
DP_X_SNK0_AUXCH_C_P0.183––
DP_X_SNK0_AUXCH_N0.342––
DP_X_SNK0_AUXCH_P0.357––
DP_X_SNK0_DDC_CLK0.562––
DP_X_SNK1_AUXCH_C_N0.183––
DP_X_SNK1_AUXCH_C_P0.185––
DP_X_SNK1_AUXCH_N0.346––
DP_X_SNK1_AUXCH_P0.361––
DP_X_SNK1_DDC_CLK0.563––
DP_X_SNK1_HPD0.471––
DP_XA_AUXCH_C_N0.345––
DP_XA_AUXCH_C_P0.361––
DP_XA_AUXCH_N0.774––
DP_XA_AUXCH_P0.773––
DP_XA_HPD0.555––
DP_XB_AUXCH_N0.771––
DP_XB_AUXCH_P0.770––
DP_XB_HPD0.556––
EDP_BKLT_EN0.488––
EDP_BKLT_PWM0.706––
EDP_COMP0.021––
EDP_INT_AUX_NOL––
EDP_INT_AUX_POL––
EDP_INT_ML_N<0>OL––
EDP_INT_ML_N<1>OL––
EDP_INT_ML_N<2>OL––
EDP_INT_ML_N<3>OL––
EDP_INT_ML_P<0>OL––
EDP_INT_ML_P<1>OL––
EDP_INT_ML_P<2>OL––
EDP_INT_ML_P<3>OL––
FAN_LT_PWM0.890––
FAN_LT_TACHOL––
GTVR_BOOT10.573––
GTVR_BOOT20.573––
GTVR_BOOT30.573––
GTVR_BP10.573––
GTVR_BP20.573––
GTVR_BP30.573––
GTVR_COMP0.573––
GTVR_COMP_L1.147––
GTVR_FB0.528––
GTVR_FB_L_10.653––
GTVR_FB_L_20.792––
GTVR_FB_L_30.001––
GTVR_FCCM0.558––
GTVR_IMON0.571––
GTVR_ISEN10.572––
GTVR_ISEN20.572––
GTVR_ISEN30.571––
GTVR_ISNS_NOL––
GTVR_ISNS_POL––
GTVR_ISNS_R_NOL––
GTVR_ISNS_R_POL––
GTVR_ISNS1_N0.0001.800–
GTVR_ISNS1_P0.0001.800–
GTVR_ISNS2_N0.0001.800–
GTVR_ISNS2_P0.0001.800–
GTVR_ISNS3_N0.0001.800–
GTVR_ISNS3_P0.0001.800–
GTVR_ISUM_IOUTOL––
GTVR_ISUM_N0.000––
GTVR_ISUM_P0.120––
GTVR_ISUMN_R0.120––
GTVR_NTC0.572––
GTVR_NTC_ROL––
GTVR_PHASE1OL––
GTVR_PHASE2OL––
GTVR_PHASE3OL––
GTVR_PWM10.559––
GTVR_PWM20.562––
GTVR_PWM30.561––
GTVR_RTN0.000––
GTVR_SW10.0001.800–
GTVR_SW20.0001.800–
GTVR_SW30.0001.800–
GTVSENSE_IN0.001––
HALL_SENSOR_LEFT0.410––
HALL_SENSOR_RIGHT1.861––
HDA_BIT_CLK0.490––
HDA_BIT_CLK_R0.479––
HDA_RST_L0.490––
HDA_RST_R_L0.480––
HDA_SDIN00.452––
HDA_SDOUT0.487––
HDA_SYNC0.492––
I2C_ALS_SCL_CONN0.487––
I2C_ALS_SDA_CONN0.475––
I2C_BKLT_SCL0.485––
I2C_BKLT_SDA0.485––
I2C_CAM_SCL0.667––
I2C_CAM_SCL_CONN0.672––
I2C_CAM_SDA0.667––
I2C_CAM_SDA_CONN0.671––
I2C_CAM_SMBDBG_CLK0.648––
I2C_CAM_SMBDBG_DAT0.648––
I2C_TBT_X_SCL0.549––
I2C_TBT_X_SDA0.547––
I2C_TBT_XA_INT_L0.547––
I2C_TBT_XB_INT_L0.550––
I2C_TCON_SCL_CONN0.648––
I2C_TCON_SDA_CONN0.657––
I2C_UPC_XA_DBG_CTL_SCL0.731––
I2C_UPC_XA_DBG_CTL_SDA0.730––
I2C_UPC_XB_DBG_CTL_SCL0.727––
I2C_UPC_XB_DBG_CTL_SDA0.729––
ISNS_1V2S3_IOUTOL––
ISNS_1V2S3_NOL––
ISNS_1V2S3_POL––
ISNS_1VS5G_IOUTOL––
ISNS_1VS5G_NOL––
ISNS_1VS5G_POL––
ISNS_3V3LCD_IOUTOL––
ISNS_3V3S5_IOUTOL––
ISNS_3V3S5_NOL––
ISNS_3V3S5_POL––
ISNS_3V3SSD_IOUT0.640––
ISNS_3V3SSD_N0.3153.300–
ISNS_3V3SSD_P0.3153.300–
ISNS_3V3WLS_IOUTOL––
ISNS_3V3WLS_NOL––
ISNS_3V3WLS_POL––
ISNS_5VS4_IOUTOL––
ISNS_5VS4_NOL––
ISNS_5VS4_POL––
ISNS_HS_COMPUTING_N0.41613.100–
ISNS_HS_COMPUTING_P0.41613.100–
ISNS_HS_COMPUTING_R_N0.416––
ISNS_HS_COMPUTING_R_P0.416––
ISNS_HS_SSD_N0.41613.100–
ISNS_HS_SSD_P0.41613.100–
ISNS_HS_TBT_N0.316––
ISNS_HS_TBT_P0.316––
ISNS_HS_TPAD_NOL––
ISNS_HS_TPAD_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.41613.100–
ISNS_LCDBKLT_P0.41613.100–
ISNS_SSD_IOUT0.641––
ISNS_TBT_IOUTOL––
ISNS_TPAD_IOUTOL––
ISUMN_A_R0.333––
ISUMN_B_L_10.334––
ISUMN_C_L_10.334––
ITP_PMODE0.298––
JTAG_ISP_TDO0.464––
JTAG_TBT_TCK0.477––
JTAG_TBT_TDI0.477––
JTAG_TBT_X_TMS0.523––
JTAG_WLAN_SEL0.550––
JTAG_WLAN_TDI0.683––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_I2C_SCLOL––
KBD_I2C_SDAOL––
KBD_INT_LOL––
L83_HSBIAS_FILT0.646––
L83_HSBIAS_FILT_REF0.555––
LCD_IRQ_L0.471––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.688––
LCDBKLT_SW0.413––
LCDBKLT_TB_XWR1.127––
LED_BKLTOL––
LED_BKLT_ROL––
LED_CATERROL––
LED_CATERR_ROL––
LED_DCINOL––
LED_DCIN_ROL––
LED_DS5OL––
LED_DS5_ROL––
LED_G3HOL––
LED_G3H_ROL––
LED_PBUSOL––
LED_PBUS_ROL––
LED_PLTRSTOL––
LED_PROCHOTOL––
LED_PROCHOT_ROL––
LED_S0IOL––
LED_S0I_ROL––
LED_S3OL––
LED_S3_ROL––
LED_S4OL––
LED_S4_ROL––
LED_S5OL––
LED_S5_ROL––
LID_OPEN1.900––
LID_OPEN_R0.479––
LPC_AD_R<0>0.473––
LPC_AD_R<1>0.474––
LPC_AD_R<2>0.473––
LPC_AD_R<3>0.475––
LPC_AD<0>0.482––
LPC_AD<1>0.482––
LPC_AD<2>0.482––
LPC_CLK24M_SMC0.498––
LPC_CLK24M_SMC_R0.489––
LPC_CLKRUN_L0.492––
LPC_FRAME_L0.484––
LPC_SERIRQ0.467––
MEM_CAM_CLK_N0.350––
MEM_CAM_CLK_P0.350––
MEM_CAM_ODT0.464––
MEM_CAM_ZQ_DDR0.087––
MEM_CAM_ZQ_S20.087––
MIPI_CLK_CONN_N0.362––
MIPI_CLK_CONN_P0.361––
MIPI_CLK_F_N0.360––
MIPI_CLK_N0.360––
MIPI_CLK_P0.357––
MIPI_DATA_CONN_N0.361––
MIPI_DATA_CONN_P0.363––
MIPI_DATA_F_N0.360––
MIPI_DATA_F_P0.360––
MIPI_DATA_N0.358––
MIPI_DATA_P0.360––
MLB_BOARD_ID00.325––
MLB_BOARD_ID10.328––
MLB_BOARD_ID20.720––
MLB_BOARD_ID30.331––
MLB_BOARD_ID40.478––
MLB_RAMCFG00.325––
MLB_RAMCFG10.334––
MLB_RAMCFG20.326––
MLB_RAMCFG30.476––
MLB_RAMCFG40.322––
NC0.704––
OPC_RCOMP0.018––
OPCE_RCOMP0.018––
P0V9_TBT_X_SVR_AGND0.159––
P1V2_CAM_SRVLXC_PHASE0.2371,200–
P1V8S0SW_CT20.700––
P1V8S3SW_CT10.700––
P1V35_CAM_SRVLXD_PHASE0.2201,350–
P1VOPC_AGND0.000––
P1VOPC_DRVH0.536––
P1VOPC_DRVL0.400––
P1VOPC_EN0.388––
P1VOPC_ENS30.329––
P1VOPC_LL_SNUBOL––
P1VOPC_MODE0.464––
P1VOPC_PGND0.000––
P1VOPC_REFIN0.557––
P1VOPC_SNS0.121––
P1VOPC_SW0.118––
P1VOPC_TRIP0.671––
P1VOPC_VBST0.572––
P1VOPC_VREF0.516––
P1VOPC_VSW0.1151.000–
P1VOPC_VTT0.534––
P1VOPC_VTTREF0.443––
P1VS5GFUSE_RAMP0.663––
P3V3_TBT_X_SX_EN0.620––
P3V3S4SW_CT10.640––
P3V3S5_COMP20.661––
P3V3S5_COMP2_R1.789––
P3V3S5_CS2_L_N0.3153.300–
P3V3S5_CS2_L_P0.3153.300–
P3V3S5_CSP20.739––
P3V3S5_DRVH0.832––
P3V3S5_DRVL0.522––
P3V3S5_DRVL_R0.522––
P3V3S5_RF0.485––
P3V3S5_SNUBROL––
P3V3S5_SW0.316––
P3V3S5_VBST0.568––
P3V3S5_VBST_R0.569––
P3V3S5_VFB20.473––
P3V3S5_VFB2_R0.315––
P3V3S5_VFB2_R20.319––
P3V3S5_VFB2_RR0.845––
P3V3S5_VSW0.3153.300–
P3V3S5GSW_CT10.700––
P5VP3V3_SKIPSEL0.426––
P5VP3V3_VREF20.426––
P5VP3V3_VREG30.482––
P5VS0SW_CT20.640––
P5VS4_COMP10.662––
P5VS4_COMP1_ROL––
P5VS4_CS1_L_N0.4075.000–
P5VS4_CS1_L_P0.4075.000–
P5VS4_CSP10.809––
P5VS4_DRVH0.921––
P5VS4_DRVL_R0.522––
P5VS4_EN0.423––
P5VS4_SW0.406––
P5VS4_VBST0.573––
P5VS4_VBST_R0.574––
P5VS4_VFB10.476––
P5VS4_VFB1_R0.407––
P5VS4_VFB1_R20.410––
P5VS4_VFB1_RR1.446––
P5VS4_VSW0.4075.000–
P5VXX_EN0.434––
PANEL_P3V3_EN0.516––
PANEL_P3V3_EN_D0.620––
PANEL_P3V3_EN_DLY0.575––
PANEL_P5V_EN0.516––
PANEL_P5V_EN_D0.653––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.418––
PBUSVSENS_EN_L0.456––
PBUSVSENS_EN_L_DIVOL––
PCH_BT_UART_CTS_L0.427––
PCH_BT_UART_D2R0.430––
PCH_BT_UART_R2D0.379––
PCH_BT_UART_RTS_L0.382––
PCH_DDPB_CTRLDATA0.610––
PCH_DDPC_CTRLDATA0.630––
PCH_DIFFCLK_BIASREF0.533––
PCH_HSIO_PWR_EN0.472––
PCH_INTRUDER_L0.780––
PCH_JTAGX0.019––
PCH_OPIRCOMP0.018––
PCH_PCIE_RCOMP_N0.249––
PCH_PCIE_RCOMP_P0.250––
PCH_SRTCRST_L0.779––
PCH_STRP_TOPBLK_SWP_L0.455––
PCH_SUSACK_L0.470––
PCH_USB2_COMP0.041––
PCH_USB2_VBUSSENSE0.334––
PCIE_CLK100M_AP_N0.243––
PCIE_CLK100M_AP_P0.244––
PCIE_CLK100M_TBT_X_N0.250––
PCIE_CLK100M_TBT_X_P0.249––
PCIE_WAKE_L0.483––
PD_PPVIOE_SSDCLK0.000––
PD_SMC_CBC_ON0.541––
PD_SOC_UART_CTS_L0.473––
PD_TBA_AGATE0.559––
PD_TBA_MPM_DET0.544––
PD_TBA_SGATE0.562––
PD_UPC_XA_GPIO50.728––
PD_UPC_XA_GPIO60.729––
PD_UPC_XB_GPIO50.725––
PD_UPC_XB_GPIO60.726––
PD_VSNS_CPU_VCCGTX_TN0.000––
PDCINVSENS_EN_L_DIVOL––
PLT_RST_L0.335––
PLTRST_LED_LOL––
PM_CLK32K_SUSCLK_R0.486––
PM_DSW_PWRGD0.703––
PM_EN_CPUVCC_R0.419––
PM_EN_P1V8S00.442––
PM_EN_P1V8S0_RC0.467––
PM_EN_P1V8S30.425––
PM_EN_P1VS0G0.434––
PM_EN_P1VS30.412––
PM_EN_P3V3_G3H0.545––
PM_EN_P3V3_G3H_R0.545––
PM_EN_P3V3S00.457––
PM_EN_P3V3S0_RC0.465––
PM_EN_P3V3S40.439––
PM_EN_P3V3S5G0.427––
PM_EN_P5VS40.423––
PM_EN_PVCCIO0.422––
PM_EN_PVXS50.436––
PM_EN_S0_SW0.430––
PM_OPC_ZVM_L0.487––
PM_PCH_PWROK0.392––
PM_PCH_PWROK_BUF0.478––
PM_PCH_SYS_PWROK0.396––
PM_PGOOD_CPUVCC0.466––
PM_PGOOD_EDRAM_R0.412––
PM_PGOOD_P1V80.408––
PM_PGOOD_P3V3S5G0.407––
PM_PGOOD_P5VS40.440––
PM_PGOOD_PVCCPCH0.400––
PM_PGOOD_PVDDQ0.412––
PM_PWRBTN_L0.469––
PM_RSMRST_L0.414––
PM_SLP_S0_L0.414––
PM_SLP_S0_OD_L0.434––
PM_SLP_S0S3_L0.434––
PM_SLP_S3_L0.387––
PM_SLP_S4_L0.412––
PM_SLP_S5_L0.444––
PM_SLP_SUS_L0.413––
PM_SYSRST_L0.482––
PM_THRMTRIP_L0.210––
PMIC_ALLSYSPGD0.417––
PMIC_EN_P3V3S50.440––
PMIC_EN3V3SW0.475––
PMIC_EN5VSW0.430––
PMIC_ENA0.408––
PMIC_ENLVA0.414––
PMIC_INT_L0.419––
PMIC_PCH_PWROK0.392––
PMIC_PGB0.426––
PMIC_PGD0.440––
PMIC_PGE0.428––
PMIC_PGH0.430––
PMIC_RSMRST_L0.414––
PMIC_SHUTDOWN_L0.434––
PMIC_SLVADDR0.433––
PMIC_SYSPWROK0.396––
PMIC_VCCST_PGD0.328––
PMIC_VDCSNS0.635––
PMIC_VSA0.306––
PMIC_VSB0.151––
PMIC_VSC0.378––
PMIC_VSD0.442––
PMIC_VSE0.320––
PMIC_VSF0.312––
PMIC_VSG0.440––
PMIC_VTT_CTRL0.263––
PP0V6_S3_MEM_VREFDQ_A0.385––
PP0V9_TBT_X_CIO0.288––
PP0V9_TBT_X_DP0.237––
PP0V9_TBT_X_LVR0.253––
PP0V9_TBT_X_PCIE0.220––
PP0V9_TBT_X_SVR0.1590.900–
PP0V9_TBT_X_USB0.343––
PP0V675_CAM_VREF0.500––
PP0V675_MEM_CAM_VREFCA0.265––
PP0V675_MEM_CAM_VREFDQ0.500––
PP1V_OPC_S00.1151.000–
PP1V_S0G0.083––
PP1V_S0SW_PCHCLKOL––
PP1V_S30.095––
PP1V_S5_PCH_DCPDSW0.306––
PP1V_S5G0,0551.000–
PP1V_S5G_PCHCLK0.055––
PP1V_S5G_REG0.0551.000–
PP1V_S5GTD0,0501,000–
PP1V_SUS_PCH_VCCCLK2_F0,0551,000–
PP1V_SUS_PCH_VCCCLK4_F0,0551,000–
PP1V_SUS_PCH_VCCCLK5_F0,0551,000–
PP1V_SUSRS0SW_PCHCLK0.046––
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0,0501,000–
PP1V1_UPC_XA_LDO_BMC0.448––
PP1V1_UPC_XB_LDO_BMC0.449––
PP1V2_CAM0.2371,200–
PP1V2_CAM_PCIE_PVDD_FLT0.3501,200–
PP1V2_CAM_PCIE_VDD_FLT0.3501,200–
PP1V2_CAM_XTALPCIEVDD0.3501.200–
PP1V2_S0G0.038––
PP1V2_S30.1301.200–
PP1V2_S3_REG0.1301.200–
PP1V2_S5_SMC_VDDC0.485––
PP1V8_CAM0.471––
PP1V8_S00.309––
PP1V8_S30.144––
PP1V8_S5G0.2001,800–
PP1V8_SUS_PCH_VCC1P8OL––
PP1V8_UPC_XA_LDOA0.469––
PP1V8_UPC_XA_LDOD0.439––
PP1V8_UPC_XB_LDOA0.475––
PP1V8_UPC_XB_LDOD0.444––
PP1V25_VREF0.428––
PP1V35_CAM0.2201,350–
PP1V35_DDR_CLK0.221––
PP2V9_SYSCLK0.416––
PP3V0_S5_AVREF_SMC0.642––
PP3V1_RTC0.400––
PP3V3_G3H0.3323,300–
PP3V3_G3H_UPC_XA0.333––
PP3V3_G3H_UPC_XB0.334––
PP3V3_G3H_VR0.3333,300–
PP3V3_LDO3V0.377––
PP3V3_S00.317––
PP3V3_S0_CPUTHMSNS_R0.336––
PP3V3_S0SW_LCD0.511––
PP3V3_S40.4133.300–
PP3V3_S4_WLS0.4133.300–
PP3V3_S50.3153.300–
PP3V3_S5_S0R0.313––
PP3V3_S5_SSD_SNS0.3153.300–
PP3V3_S5_TBT_X_SW0.425––
PP3V3_S5G0.303––
PP3V3_SSD_FLT0.3153.300–
PP3V3_TBT_X_ANA_PCIE0.484––
PP3V3_TBT_X_ANA_USB20.455––
PP3V3_TBT_X_F0.3173,300–
PP3V3_TBT_X_LC0.505––
PP3V3_TBT_X_S00.3173,300–
PP3V3_UPC_XA_LDO0.478––
PP3V3_UPC_XB_LDO0.484––
PP5V_LDO5V0.410––
PP5V_S00.416––
PP5V_S0_ALSCAM_F0.413––
PP5V_S0_BKLT_A0.416––
PP5V_S0_BKLT_D0.417––
PP5V_S0_P1VOPC0.418––
PP5V_S0SW_LCD0.513––
PP5V_S40.4075.000–
PP5V_S4_TPAD_CONN0.406––
PP5V_S50.3975.000–
PP5VR7V_VPROGOTP0.410––
PP20V_USBC_XA_VBUS0.18020,000–
PP20V_USBC_XA_VBUS_CONN0.15420.000–
PP20V_USBC_XA_VBUS_F0.18020,000–
PP20V_USBC_XB_VBUS0.18020,000–
PP20V_USBC_XB_VBUS_CONN0.15420.000–
PP20V_USBC_XB_VBUS_F0.18020,000–
PPBUS_G3H0.41613.100–
PPBUS_G3H_CPU0.41613.100–
PPBUS_G3H_P3V3S50.4143.300–
PPBUS_G3H_P5VS40.41613,100–
PPBUS_G3H_R0.416––
PPBUS_G3H_SPKRL0.41613.100–
PPBUS_G3H_SSD0.41613.100–
PPBUS_G3H_TPAD0.41613.100–
PPBUS_PMIC0.420––
PPBUS_SSD_FLT0.41613.100–
PPDCIN_G3H0.51520.000–
PPDCIN_G3H_CHGR0.51520.000–
PPDCIN_G3H_CHGR_R0.516––
PPDCIN_G3H_VSNS_IN0.515––
PPDCPRTC_PCH0.595––
PPVBAT_G3H_CHGR_R0.41613.100–
PPVBAT_G3H_CHGR_REG0.41613.100–
PPVBAT_G3H_CONN0.57113.100–
PPVCCCPU_S0G0.0011.800–
PPVCCCPU_S0G_PH10.0011.800–
PPVCCCPU_S0G_PH20.0011.800–
PPVCCGT_S0G0.0001.800–
PPVCCGT_S0G_PH10.0001.8002.000R
PPVCCGT_S0G_PH20.0001.8002.000R
PPVCCGT_S0G_PH30.0001.8002.000R
PPVCCIO_S0G0.0750.950–
PPVCCOPC_S0G0.010––
PPVCCPCH_S5G0.0351.000–
PPVCCSA_S0G0.0021.500–
PPVCCSA_S0G_R0.0021.500–
PPVIN_G3H_P3V3G3H0.522––
PPVIN_S0SW_LCDBKLT0.82012.900–
PPVIN_S0SW_LCDBKLT_F0.41613.100–
PPVIN_S0SW_LCDBKLT_R0.41613.100–
PPVIN_S4_TPAD_FUSE0.41613.100–
PPVIN_SW_LCDBKLT_SW0.82012.900–
PPVIOE_CAMCLK0.309––
PPVOUT_S0_LCDBKLT1.11755.000–
PPVTT_S00.070––
PROCHOT_LEDOL––
PROCHOT_LED_LOL––
PROG10.570––
PROG20.570––
PROG30.498––
PROG40.571––
PROG50.571––
PSYS0.564––
PU_PCH_RCIN_L0.485––
PU_SOC_UART_D2R0.471––
PU_SSD_UART_D2R0.470––
PU_SSD_UART_R2D0.472––
PU_TBT_T_PLUG_EVENT_L0.704––
RTC_RESET_L0.779––
S5_PWRGD0.442––
SAVE_CC1A_B1.168––
SAVE_CC1A_G0.588––
SAVE_CC1A_Z1.133––
SAVE_CC1B_B1.168––
SAVE_CC1B_G0.603––
SAVE_CC1B_Z1.125––
SAVE_CC2A_B1.165––
SAVE_CC2A_G0.584––
SAVE_CC2A_Z1.133––
SAVE_CC2B_B1.168––
SAVE_CC2B_G0.600––
SAVE_CC2B_Z1.130––
SAVR_BOOT0.575––
SAVR_COMP0.572––
SAVR_COMP_L1.509––
SAVR_FB0.512––
SAVR_FB_L_10.667––
SAVR_FB_L_21.019––
SAVR_FB_L_30.002––
SAVR_FCCM0.563––
SAVR_IMON0.572––
SAVR_ISNS_IOUTOL––
SAVR_ISNS_NOL––
SAVR_ISNS_POL––
SAVR_ISNSR_N0.0021.500–
SAVR_ISNSR_P0.0021.500–
SAVR_ISUM_N0.002––
SAVR_ISUM_P0.335––
SAVR_ISUMN_R0.152––
SAVR_PHASE0.002––
SAVR_PWM0.561––
SAVR_SW0.0021.500–
SCLK0.130––
SDA0.117––
SMB_PMIC_SCL0.380––
SMB_PMIC_SDA0.379––
SMBUS_PCH_CLK0.507––
SMBUS_PCH_DATA0.500––
SMBUS_SMC_0_S0_SCL0.640––
SMBUS_SMC_0_S0_SDA0.651––
SMBUS_SMC_1_S0_SCL0.484––
SMBUS_SMC_1_S0_SDA0.469––
SMBUS_SMC_3_S0_SCL0.650––
SMBUS_SMC_3_S0_SDA0.654––
SMBUS_SMC_4_G3_SCL0.634––
SMBUS_SMC_4_G3_SDA0.634––
SMBUS_SMC_5_G3H_SCL0.379––
SMBUS_SMC_5_G3H_SDA0.379––
SMC_1V2S3_ISENSE0.686––
SMC_1VS5G_ISENSE0.694––
SMC_3V3LCD_ISENSE0.683––
SMC_3V3S5_ISENSE0.694––
SMC_3V3SSD_ISENSE0.672––
SMC_3V3WLS_ISENSE0.689––
SMC_5VS4_ISENSE0.693––
SMC_AUX_OK-0.545––
SMC_BC_ACOK0.545––
SMC_BMON_ISENSE0.657––
SMC_BT_PWR_EN0.425––
SMC_CHGR_INT_L0.544––
SMC_CLK12M_EN0.416––
SMC_CLK32K0.493––
SMC_CPU_HI_ISENSE0.630––
SMC_CPU_IMON_ISENSE0.686––
SMC_CPU_ISENSE0.665––
SMC_CPU_VSENSE0.624––
SMC_DCIN_ISENSE0.667––
SMC_DCIN_VSENSE0.645––
SMC_DEBUGPRT_RX_L0.680––
SMC_DEBUGPRT_TX_L0.645––
SMC_DELAYED_PWRGD0.702––
SMC_DEV_SUPPLY_L0.952––
SMC_DEV_SUPPLY_R_L0.707––
SMC_DP_HPD_L0.707––
SMC_FAN_0_CTL0.707––
SMC_FAN_0_TACH0.706––
SMC_GT_ISENSE0.666––
SMC_GT_VSENSE0.649––
SMC_LCDBKLT_ISENSE0.679––
SMC_LID_LEFT0.483––
SMC_LID_LEFT_R0.482––
SMC_LID_RIGHT0.420––
SMC_LRESET_L0.349––
SMC_LSOC_RST0.552––
SMC_MPM_OK0.548––
SMC_ONOFF_L0.704––
SMC_ONOFF_R_LOL––
SMC_OOB1_D2R_L0.703––
SMC_OOB1_R2D_L0.701––
SMC_PBUS_VSENSE0.655––
SMC_PCH_SUSACK_L0.471––
SMC_PCH_SUSWARN_L0.475––
SMC_PECI_L0.657––
SMC_PM_G2_EN0.469––
SMC_PME_S4_DARK_L0.477––
SMC_PME_S4_WAKE_L0.697––
SMC_PMIC_INT_L0.419––
SMC_PROCHOT0.700––
SMC_PROCHOT_L0.308––
SMC_RESET_L0.550––
SMC_RESET_R_L0.539––
SMC_RST_BTN_LOL––
SMC_RST_BTN_R_LOL––
SMC_RST_IN0.552––
SMC_RUNTIME_SCI_L0.475––
SMC_RX_L0.703––
SMC_SA_IMON_ISENSE0.692––
SMC_SA_ISENSE0.692––
SMC_SENSOR_ALERT_L0.555––
SMC_SENSOR_PWR_EN0.704––
SMC_TCK0.690––
SMC_TCON_BKLT_PWM0.702––
SMC_TDI0.704––
SMC_TDO0.704––
SMC_THRMTRIP0.689––
SMC_THRMTRIP_L0.243––
SMC_TMS0.689––
SMC_TOPBLK_SWP_L0.508––
SMC_TPAD_ISENSE0.688––
SMC_TX_L0.703––
SMC_USBC_INT_L0.614––
SMC_VCCIO_CPU_DIV20.665––
SMC_VIBE_L0.700––
SMC_WAKE_L0.707––
SMC_WIFI_EVENT_L0.587––
SMC_WIFI_PWR_EN0.398––
SML_PCH_0_CLK0.700––
SML_PCH_0_DATA0.700––
SPI_ALT_CLK0.479––
SPI_ALT_CS_L0.474––
SPI_ALT_IO<2>0.473––
SPI_ALT_IO<3>0.476––
SPI_ALT_MISO0.476––
SPI_ALT_MOSI0.484––
SPI_CLK_R0.474––
SPI_CS0_R_L0.466––
SPI_DESCRIPTOR_OVERRIDE0.751––
SPI_DESCRIPTOR_OVERRIDE_L0.669––
SPI_IO<2>0.466––
SPI_IO<3>0.467––
SPI_IO2_STRAP_LOL––
SPI_MISO0.467––
SPI_MLB_CLK0.477––
SPI_MLB_CS_L0.472––
SPI_MLB_IO<2>0.472––
SPI_MLB_IO<3>0.475––
SPI_MLB_MISO0.475––
SPI_MLB_MOSI0.483––
SPI_MLBROM_CS_L0.534––
SPI_MOSI_R0.476––
SPIROM_USE_MLB0.469––
SPKRAMP_5V_10.527––
SPKRAMP_5V_20.527––
SPKRAMP_BSTN_10.561––
SPKRAMP_BSTN_20.560––
SPKRAMP_BSTP_10.561––
SPKRAMP_BSTP_20.560––
SPKRAMP_FL_OUT_N0.463––
SPKRAMP_FL_OUT_P0.462––
SPKRAMP_RL_OUT_N0.462––
SPKRAMP_RL_OUT_P0.462––
SPKRCONN_FL_OUT_N0.463––
SPKRCONN_FL_OUT_P0.462––
SPKRCONN_RL_OUT_N0.462––
SPKRCONN_RL_OUT_P0.462––
SSD_BOOT_CONN_L0.633––
SSD_BOOT_L0.633––
SSD_CLKREQ_L0.744––
SSD_ENOL––
SSD_JTAG_TCK0.729––
SSD_JTAG_TMS0.729––
SSD_PWR_EN_CONN_L0.635––
SSD_PWR_EN_L0.478––
SSD_PWR_REQ0.505––
SSD_RESET_L0.713––
SSD_SR_EN_L0.481––
SWOPC_CNFG0.522––
SWOPC_G0.521––
SYS_DETECT_L1.697––
SYSCLK_CLK12M_SMC0.410––
SYSCLK_CLK24M_CAMERA0.406––
SYSCLK_CLK24M_PCH0.405––
SYSCLK_CLK24M_X10.415––
SYSCLK_CLK24M_X20.417––
SYSCLK_CLK24M_X2_R0.416––
SYSCLK_CLK32K_BT_AP0.430––
SYSCLK_CLK32K_BT_AP_R0.410––
SYSCLK_CLK32K_PCH0.427––
SYSRST_R_LOL––
TBA_AUX_DET0.553––
TBA_BGATE0.572––
TBA_BOOT10.547––
TBA_BOOT1_RC0.547––
TBA_BOOT20.544––
TBA_BOOT2_RC0.544––
TBA_COMP0.550––
TBA_CSI_N0.51520.000–
TBA_CSI_P0.51520.000–
TBA_CSIR_N0.51620,000–
TBA_CSIR_P0.51620,000–
TBA_CSO_N0.41613.100–
TBA_CSO_P0.41613.100–
TBA_CSOR_N0.41713,100–
TBA_CSOR_P0.41513,100–
TBA_GATE_Q10.740––
TBA_GATE_Q20.420––
TBA_GATE_Q40.739––
TBA_HPWR_EN_L0.552––
TBA_LX10.326––
TBA_LX20.326––
TBA_PHASE10.33013.100–
TBA_PHASE20.33013.100–
TBA_VDDA0.411––
TBA_VDDP0.410––
TBT_POC_RESET0.635––
TBT_X_CIO_PLUG_EVENT_L0.539––
TBT_X_CIO_PWR_EN0.479––
TBT_X_CLKREQ_L0.545––
TBT_X_FORCE_PWR0.561––
TBT_X_PCIE_BIAS0.636––
TBT_X_RBIAS0.690––
TBT_X_ROM_HOLD_L0.639––
TBT_X_ROM_WP_L0.550––
TBT_X_RSENSE0.000––
TBT_X_SPI_CLK0.526––
TBT_X_SPI_CLK_DBG0.557––
TBT_X_SPI_CS_L0.555––
TBT_X_SPI_MISO0.556––
TBT_X_SPI_MOSI0.561––
TBT_X_TEST_EN0.037––
TBT_X_THERM_D_N0.000––
TBT_X_THERM_D_P0.818––
TBT_X_USB_PWR_EN0.480––
TBT_XA_USB2_RBIAS0.176––
TBT_XB_USB2_RBIAS0.177––
TBTXPOCRST_CT0.592––
TBTXPOCRST_SNS1.046––
TCON_BKLT_PWM0.693––
TP_CAM_JTAG_SRST_L0.505––
TP_CAM_JTAG_TCK0.505––
TP_CAM_JTAG_TDI0.510––
TP_CAM_JTAG_TDO0.505––
TP_CAM_JTAG_TMS0.480––
TP_CAM_JTAG_TRST_L0.502––
TP_CAM_LV_JTAG_TCK0.508––
TP_CAM_LV_JTAG_TDI0.505––
TP_CAM_LV_JTAG_TDO0.485––
TP_CAM_LV_JTAG_TMS0.506––
TP_CAM_LV_JTAG_TRSTN0.490––
TP_CAM_PCIE_WAKE_L0.447––
TP_CAM_RAMCFG00.505––
TP_CAM_RAMCFG10.505––
TP_CAM_RAMCFG20.505––
TP_CAM_TEST_MODE00.508––
TP_CAM_TEST_MODE10.503––
TP_CAM_TEST_MODE20.503––
TP_CAM_UARTRTS0.510––
TP_CAM_UARTTXD0.520––
TP_CPU_PWRGD0.323––
TP_CPUVR_GH2OL––
TP_CPUVR_GL10.409––
TP_CPUVR_GL20.402––
TP_GTVR_GH1OL––
TP_GTVR_GH2OL––
TP_GTVR_GH3OL––
TP_GTVR_GL10.403––
TP_GTVR_GL20.406––
TP_GTVR_GL30.404––
TP_ISNS_3V3S0NOL––
TP_ISNS_3V3S0POL––
TP_ISNS_SKPRLN0.41613.100–
TP_ISNS_SKPRLP0.41613.100–
TP_JTAG_WLAN_TCK0.537––
TP_JTAG_WLAN_TDO0.520––
TP_JTAG_WLAN_TMS0.533––
TP_JTAG_WLAN_TRST0.565––
TP_PCH_SLP_A_L0.479––
TP_SAVR_GHOL––
TP_SAVR_GL0.415––
TP_SPKR_ID10.476––
TP_UPC_XA_DBG_UART_RX0.724––
TP_UPC_XA_DBG_UART_TX0.730––
TP_UPC_XB_DBG_UART_RX0.722––
TP_UPC_XB_DBG_UART_TX0.728––
TP_USBC_XA_RESET_L0.732––
TP_WLAN_UART_R2D0.520––
TPAD_SPI_CLK0.486––
TPAD_SPI_CS_CONN_L0.468––
TPAD_SPI_CS_L0.447––
TPAD_SPI_IF_EN0.475––
TPAD_SPI_INT_L0.470––
TPAD_SPI_MISO0.476––
TPAD_SPI_MOSI0.481––
TPAD_VIBE_L0.700––
TSNS_1_A0OL––
TSNS_1_A1OL––
TSNS_1_NOL––
TSNS_1_POL––
TSNS_2_A0OL––
TSNS_2_A1OL––
TSNS_3_N0.548––
TSNS_3_P0.549––
TSP_UPC_XB_SWD_CLK0.703––
UPC_XA_BUSPOWERZ0.000––
UPC_XA_DBG30.729––
UPC_XA_DBG40.726––
UPC_XA_FAULT_L0.507––
UPC_XA_GATE10.617––
UPC_XA_GATE20.609––
UPC_XA_I2C_ADDR0.000––
UPC_XA_R_OSC0.470––
UPC_XA_SS0.465––
UPC_XA_UART_RX0.687––
UPC_XA_UART_TX0.689––
UPC_XB_BUSPOWERZ0.000––
UPC_XB_FAULT_L0.505––
UPC_XB_GATE10.618––
UPC_XB_GATE20.610––
UPC_XB_R_OSC0.470––
UPC_XB_SPI_CLK0.530––
UPC_XB_SPI_CS_L0.557––
UPC_XB_SPI_MISO0.559––
UPC_XB_SPI_MOSI0.564––
USB_TESTER_N0.468––
USB_TESTER_P0.469––
USB_UPC_PCH_XA_N0.475––
USB_UPC_PCH_XA_P0.476––
USB_UPC_PCH_XB_N0.472––
USB_UPC_PCH_XB_P0.472––
USB_UPC_XA_F_P0.477––
USB3_EXTA_D2R_N0.288––
USB3_EXTA_D2R_P0.289––
USB3_EXTA_R2D_NOL––
USB3_EXTA_R2D_POL––
USBC_X_RESET_L0.452––
USBC_X_RESET_L_R0.476––
USBC_XA_CC10.590––
USBC_XA_CC1_CONN0.612––
USBC_XA_CC20.593––
USBC_XA_CC2_CONN0.618––
USBC_XA_RPD_G10.590––
USBC_XA_RPD_G20.592––
USBC_XA_SBU1OL––
USBC_XA_SBU2OL––
USBC_XB_CC10.586––
USBC_XB_CC1_CONN0.608––
USBC_XB_CC20.591––
USBC_XB_CC2_CONN0.613––
USBC_XB_RPD_G10.586––
USBC_XB_RPD_G20.591––
USBC_XB_SBU1OL––
USBC_XB_SBU2OL––
V3V3G3H_BIAS0.536––
V3V3G3H_BOOST0.579––
V3V3G3H_BST_R0.579––
V3V3G3H_FB0.555––
V3V3G3H_FB_R0.336––
V3V3G3H_FB_R20.463––
V3V3G3H_FB_XW0.333––
V3V3G3H_SW0.3333,300–
VCINP_P5V_U74700.419––
VCINP_P5V_U75100.418––
VCINP_P5V_U75200.418––
VCINP_P5V_U75300.418––
VR_HOT_L0.280––
VR0V9_IND_TBT_X0.1590.900–
WA_P0V9TBTXLVR_Q0.554––
WLAN_ROM_CLK0.633––
WLAN_ROM_CS0.617––
WLAN_ROM_MISO0.582––
WLAN_ROM_MOSI0.632––
WLAN_ROM_ORG0.653––
XDP_CPU_PRDY_L0.223––
XDP_CPU_PREQ_L0.239––
XDP_CPU_PWRBTN_L0.472––
XDP_CPU_TCK0.018––
XDP_CPU_TDI0.101––
XDP_CPU_TDO0.092––
XDP_CPU_TMS0.101––
XDP_CPU_TRST_L0.246––
XDP_DBRESET_L0.482––
XDP_JTAG_ISP_TCK0.478––
XDP_JTAG_ISP_TDI0.478––
XDP_PCH_OBSDATA_A20.477––
XDP_PCH_OBSDATA_A30.478––
XDP_PCH_OBSDATA_B00.480––
XDP_PCH_OBSDATA_C00.477––
XDP_PCH_OBSDATA_C10.478––
XDP_PCH_OBSDATA_C20.477––
XDP_PCH_OBSDATA_C30.478––
XDP_PCH_OBSDATA_D00.478––
XDP_PCH_OBSDATA_D10.477––
XDP_PCH_OBSDATA_D20.476––
XDP_PCH_OBSDATA_D30.478––
XDP_PCH_OBSFN_C10.477––
XDP_PCH_TCK0.297––
XDP_PCH_TDI0.102––
XDP_PCH_TDO0.093––
XDP_PCH_TMS0.101––
XDP_PCH_TRST_L0.246––
XDP_PM_RSMRST_L0.704––
XDP_PRESENT_CPU0.545––
XDP_PRESENT_LOL––
XDP_USB_EXTA_OC_L0.507––
XDP_USB_EXTB_OC_L0.505––
XDP_USB_EXTC_OC_L0.509––
XDP_USB_EXTD_OC_L0.513––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00875?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00875: diode 0.416, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00875?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00875: diode 0.332, voltage 3,300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00875?

OpenBoardData's known-good values for PP5V_S5 on the 820-00875: diode 0.397, voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00875 board?

Open your own 820-00875 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License