Apple laptop board · OpenBoardData

820-01598 known-good readings

Known-good readings for the Apple laptop board 820-01598: 1,476 nets, including 106 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 104 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01598.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 106 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 47

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.338––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V always-on rail in the G3H group, which comes from its name; the boot sequence places it after P1V8G3S_EN and before P5VG3S_PGOOD. The only known-good reading here is a diode value of 0.338 to ground; no known-good voltage reading is listed. With the board unpowered, measure diode mode from PP1V8_G3S to ground and compare with 0.338 as a guide, then power up and check the voltage at the rail. A diode reading far below 0.338 suggests a short or a leaky load on the rail; far above it suggests an open path, so trace P1V8G3S_EN and the rail's source next.

PP1V8_G3S_REG0.338––
AI: what PP1V8_G3S_REG is and how to check it

PP1V8_G3S_REG is a 1.8 V G3S rail; the "G3S" part of the name marks it as an always-on startup rail, and "_REG" suggests it comes from a regulator rather than a direct supply. The only known-good figure here is a diode reading of 0.338 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode value far below 0.338 usually points to a short or a leaky part on the rail, while a much higher one suggests an open path; a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V8_G3S_WLANBT0.341––
AI: what PP1V8_G3S_WLANBT is and how to check it
  • What it is: PP1V8_G3S_WLANBT is a 1.8 V rail for the WLAN/Bluetooth section. From its name, the G3S part means it belongs to the G3H "always on" startup stage, so it should be present early in the boot sequence, before the S5/S3/S0 rails.
  • Known-good reading: diode 0.341 to ground, from the readings archive. That is a community guide, not a factory spec, and no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.341. Then apply power and measure the DC voltage on the rail; there is no known-good voltage value here, so compare against a matching rail or a known-good board.
  • If it's far off: a diode reading well below 0.341 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken trace or missing supply. Confirm with the voltage measurement before replacing anything.
PP3V_G3H_RTC0.511––
AI: what PP3V_G3H_RTC is and how to check it

PP3V_G3H_RTC is the always-on 3.3 V RTC rail; the G3H in its name means it should be present whenever the board has power, before the main sequence starts. The only known-good reading here is a diode value of 0.511 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied. A diode reading far below 0.511 suggests a short or a leaky load on the rail; a far higher or open reading suggests a broken trace or missing connection. Treat the value as a community guide and compare against a matching rail on a known-good board where possible.

PP3V3_G3H0.4203.300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail from the G3H group, which the name marks as always on; in the boot sequence it comes up early, right after PBUS and PP3V3_G3H_RTC. Known-good readings in the archive are diode 0.420 and voltage 3.300, with no condition recorded. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.420 suggests a short or a damaged component on the rail; a voltage well below 3.300 points to the rail not coming up or being loaded down. There is no known-good resistance reading here, so compare against a matching net or a known-good board.

PP3V3_G3H_BMU0.414––
AI: what PP3V3_G3H_BMU is and how to check it

PP3V3_G3H_BMU is a 3.3 V always-on rail; the G3H part of the name indicates it's present whenever external power or battery is connected, before the main power sequence. The only known-good figure here is a diode reading of 0.414 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.414.
  • Then apply power and measure the voltage; expect about 3.3 V (general expectation from the name, not a recorded value).

A diode reading far below 0.414 usually suggests a short or a leaky part on the rail; far above it can mean an open connection. A missing or low voltage with a normal diode reading points more toward the rail's source or its enable, not a short. These are likely causes only, not confirmed.

PP3V3_G3H_MESA_SW0.427––
AI: what PP3V3_G3H_MESA_SW is and how to check it
  • What it is: From the name, a 3.3 V always-on (G3H) switched rail for the MESA section. It belongs to the always-on startup stage, before the main rails come up.
  • Known-good reading: diode 0.427 to ground (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP3V3_G3H_PMU_VDDMAIN0.422––
AI: what PP3V3_G3H_PMU_VDDMAIN is and how to check it
  • What it is: From the name, a 3.3 V always-on (G3H) supply feeding the PMU's VDDMAIN input. It belongs to the always-on startup stage, so it should be present before the later sequenced rails.
  • Known-good reading: diode 0.422 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the net to ground and compare with 0.422. Then apply power and measure the voltage on the net; no known-good voltage is listed, so compare with a known-good board or a matching always-on 3.3 V rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; an open or high reading suggests a broken feed or enable. Confirm with a second measurement before replacing anything.
PP3V3_G3H_PMU_VINRTC_R0.429––
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check it

PP3V3_G3H_PMU_VINRTC_R — from the name, a 3.3 V always-on (G3H) rail feeding the PMU's RTC input (VINRTC). It sits at the very start of the boot sequence, ahead of PP1V8_SLPS2R.

  • Known-good: diode-to-ground 0.429 (community reading, a guide only; varies with board state). No known-good voltage reading here.
  • Check: board unpowered, diode mode, black probe on ground, red on the rail. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.429 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with a voltage check before replacing anything.
PP3V3_G3H_RTC0.430––
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC — from the name, a 3.3 V always-on (G3H) rail feeding the RTC domain. It sits early in the boot sequence, right after PBUS, so it should be present whenever a valid external PSU, battery or charger is connected.

  • Known-good: diode mode to ground 0.430 (community reading, a guide only; no known-good voltage is recorded here).
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power the board and measure the DC voltage on the rail.
  • A diode reading far from 0.430 suggests a short or a damaged component on that rail; a missing voltage with a normal diode reading points more to the upstream supply or enable. Neither is confirmed until you measure.
PP3V3_G3H_RTC_DFR0.416––
AI: what PP3V3_G3H_RTC_DFR is and how to check it

PP3V3_G3H_RTC_DFR — a 3.3 V always-on rail in the RTC/DFR area, judging from its name (G3H = always on, RTC = real-time clock domain). It sits in the earliest startup stage, alongside PP3V3_G3H_RTC and PP3V3_G3H, before PP1V8_SLPS2R.

  • Known-good: diode mode to ground 0.416 (community reading, a guide only; board state varies).
  • Check: power off and unplug, diode mode black probe to ground, red on the rail; then power up and measure DC voltage on the rail.
  • No known-good voltage reading here — compare against a matching always-on 3.3 V rail or a known-good board.
  • A diode reading far below 0.416 suggests a short or leaky load on the rail; far above suggests an open trace or missing part. Neither confirms a bad part on one reading.
PP3V3_G3H_RTC_MESA0.430––
AI: what PP3V3_G3H_RTC_MESA is and how to check it

PP3V3_G3H_RTC_MESA is a 3.3 V always-on rail in the G3H (always-on) startup stage, judging from its name; it sits alongside PP3V3_G3H_RTC and PP3V3_G3H near the top of the boot sequence. The archive lists one known-good reading: diode 0.430 (no condition given). Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then confirm the voltage with power applied. A diode reading far from 0.430 usually points to a short or a damaged component on that net, but one reading isn't proof, so recheck before replacing anything. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PP3V3_G3H_RTC_REG_R0.4253.300–
AI: what PP3V3_G3H_RTC_REG_R is and how to check it

PP3V3_G3H_RTC_REG_R is the always-on 3.3 V RTC rail in the G3H startup stage, judged from the name (G3H = always on, RTC = real-time clock domain). Known-good readings from the archive: diode 0.425 to ground and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.425 usually points to a short or a leaky part on the rail, while a missing 3.300 V points upstream to the RTC supply or its enable. No known-good resistance reading exists for this rail.

PP3V3_G3H_SSD00.417––
AI: what PP3V3_G3H_SSD0 is and how to check it

PP3V3_G3H_SSD0 — from its name, a 3.3 V always-on (G3H) rail feeding the SSD section (SSD0). The archive lists one known-good diode reading: 0.417 to ground, with no condition noted. No known-good voltage reading is recorded here.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.417.
  • Then apply power and measure the voltage on the rail; the archive gives no expected figure, so compare against a known-good board or matching rail.
  • A diode reading far below 0.417 suggests a short or leaky part on the rail; far above suggests an open path. Either is a guide, not proof a part is bad.
PP3V3_G3HSW_DFR0.579––
AI: what PP3V3_G3HSW_DFR is and how to check it
  • What it is: From its name, PP3V3_G3HSW_DFR is a 3.3 V G3H-stage rail with a switched (SW) and DFR variant; G3H rails are always-on in this board's boot sequence.
  • Known-good reading: diode 0.579 to ground (community archive value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a voltage measurement before suspecting any part.
PP3V3_G3S0.365––
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is a 3.3 V rail in the G3S (always-on) domain, judged from its name; in the boot sequence it comes up after P3V3G3S_EN and before P1V8G3S_EN and PP1V8_G3S. The only known-good reading here is diode mode to ground: 0.365, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. There is no known-good voltage reading for this rail in the data, so compare against a known-good board or the matching rail on a paired side. A diode reading far from 0.365 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_G3S_KBD0.368––
AI: what PP3V3_G3S_KBD is and how to check it

Reference note for PP3V3_G3S_KBD on 820-01598:

  • The name indicates a 3.3 V rail in the G3S (suspend-to-RAM / trickle-on) domain, and "KBD" suggests it feeds keyboard circuitry. That reading is from the name only; the parts on this net aren't documented here.
  • Known-good: diode 0.368 to ground (community reading, guide only). No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.368 usually points to a short or a leaky load on the rail; confirm with a resistance check and compare against a known-good board before replacing anything.
PP3V3_G3S_TPAD0.3336––
AI: what PP3V3_G3S_TPAD is and how to check it

PP3V3_G3S_TPAD is a 3.3 V G3S rail, most likely the trackpad's supply; the G3S stage comes from the rail name, and the boot sequence lists PP3V3_G3S as a step after PP5V_G3S and before PP1V8_G3S. The only known-good reading here is a diode value of 0.3336 to ground, with no condition recorded, and there is no known-good voltage reading for this net. With the board unpowered, measure diode mode from PP3V3_G3S_TPAD to ground and compare with 0.3336; then power up and check the voltage, comparing against PP3V3_G3S on the same stage since no voltage value exists for the TPAD net. A diode reading far below 0.3336 usually points to a short or a damaged part on the rail, while a much higher one can mean an open path; treat these as guides, not proof.

PP3V3_G3S_WLANBT0.365––
AI: what PP3V3_G3S_WLANBT is and how to check it
  • What it is: PP3V3_G3S_WLANBT is a 3.3 V always-on rail feeding the WLAN/Bluetooth section, from its name. The G3S stage in the boot sequence is always on, so it should be present whenever the board has valid power.
  • Known-good reading: diode 0.365 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.365. Then apply power and measure the voltage; expect about 3.3 V, though that figure is general, not from this board's data.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points to the rail's supply or enable. This is a guide, not a confirmed diagnosis.
PP5V_G3H_LDO0.489––
AI: what PP5V_G3H_LDO is and how to check it

PP5V_G3H_LDO is a 5 V always-on rail; the G3H part of the name indicates it comes up in the always-on startup stage, before the main power sequence. The only known-good figure here is a diode reading of 0.489 to ground, with no condition recorded; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from PP5V_G3H_LDO to ground and compare with 0.489.
  • Then apply power and measure the voltage on the rail; a 5 V name suggests roughly 5 V, but that is general expectation, not a recorded value here.

A diode reading far below 0.489 usually points to a short or a leaky part on the rail; a reading far above it can mean an open connection. Either way, confirm with a second measurement before suspecting a part.

PP5V_G3S0.4205.000–
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V always-on rail (the G3S suffix is from the name), and it appears in the boot sequence after P5VG3S_EN and before PP3V3_G3S and P5VG3S_PGOOD. Known-good readings from the archive: diode 0.420 to ground and 5.000 V with power applied; no known-good resistance value here. Check it unpowered in diode mode from PP5V_G3S to ground, then power the board and measure the voltage. A diode reading far from 0.420 suggests a short or leaky part on the rail; the voltage missing or low points back to its enable, P5VG3S_EN, or the supply that makes it. These are community guide values, not a confirmed diagnosis.

PP5V_G3S_ALSCAM0.426––
AI: what PP5V_G3S_ALSCAM is and how to check it

PP5V_G3S_ALSCAM is a 5 V always-on rail, judging from its G3S name (G3H/G3S rails are the always-present startup rails on this board). The only known-good reading here is a diode value of 0.426; there is no known-good voltage or resistance reading for it.

  • With the board unpowered, measure diode mode from PP5V_G3S_ALSCAM to ground and compare with 0.426.
  • Then power the board and check the rail sits near 5 V.

A diode reading far below 0.426 usually points to a short or a leaky load on the rail; a much higher or open reading points to a broken trace or missing source. These are general guidelines, not confirmed causes from this board's data.

PP5V_G3S_CPUREG_MISC0.426––
AI: what PP5V_G3S_CPUREG_MISC is and how to check it
  • What it is: From its name, PP5V_G3S_CPUREG_MISC is a 5 V rail in the G3S group (G3H: always on per the startup stage), feeding CPU regulator "misc" circuitry. The data doesn't list which parts sit on it.
  • Known-good: diode reading to ground 0.426 (community archive, guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far from 0.426: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open trace or missing part. Confirm with a voltage check and compare against a matching rail before replacing anything.
PP5V_G3S_DFR_FILT0.4195––
AI: what PP5V_G3S_DFR_FILT is and how to check it

PP5V_G3S_DFR_FILT is a 5 V G3S rail; the G3S part of the name places it in the G3H always-on startup stage, and "FILT" suggests a filtered version of the 5 V G3S supply (that reading is from the name, not the data).

  • Known-good: diode 0.4195 to ground (community archive, board state not stated). No known-good voltage reading here.
  • Check unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage.
  • A diode reading far below 0.4195 usually points to a short or a leaky load on the rail; far above it can mean an open path. Confirm with a second measurement before replacing anything.
PP5V_G3S_EDRAMPVCC0.427––
AI: what PP5V_G3S_EDRAMPVCC is and how to check it
  • What it is: From the name, a 5 V rail (PP5V) in the G3S (always-on) domain that feeds EDRAM PVCC. The name is the only description available here; which parts sit on the net isn't known.
  • Known-good reading: diode 0.427 to ground (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, then diode mode from the rail to ground; then power the board and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP5V_G3S_EDRAMVCC0.427––
AI: what PP5V_G3S_EDRAMVCC is and how to check it

PP5V_G3S_EDRAMVCC is a 5 V rail in the G3S (always-on) group, judging by its name; the "EDRAMVCC" suffix suggests it supplies memory. The only known-good figure here is a diode reading of 0.427 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage is listed. A diode reading far from 0.427 usually points to a short or a damaged component on that rail, but one reading isn't proof — compare against a known-good board before replacing anything.

PP5V_G3S_FAN_CONN0.4154––
AI: what PP5V_G3S_FAN_CONN is and how to check it

PP5V_G3S_FAN_CONN is the 5 V fan connector rail; the G3S part of the name indicates it belongs to the G3S (always-on) supply group, and this is from the name rather than a schematic. The only known-good figure here is a diode reading of 0.4154 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the connector. A diode reading far below 0.4154 usually suggests a short or a leaky load on the rail, while a much higher reading can mean an open trace or a missing connection; confirm with a voltage check before replacing anything.

PP5V_G3S_KBD0.426––
AI: what PP5V_G3S_KBD is and how to check it

PP5V_G3S_KBD is a 5 V always-on rail in the G3S group, judging from its name (G3H/G3S rails are the always-present rails in the boot sequence). The archive lists one known-good diode reading of 0.426 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied. A diode reading far below 0.426 usually points to a short or a leaky part on that rail; a far higher or open reading points to a broken trace or missing connection. Confirm with a second measurement before replacing anything.

PP5V_G3S_TPAD0.423––
AI: what PP5V_G3S_TPAD is and how to check it

PP5V_G3S_TPAD is a 5 V rail in the G3S (always-on) group, judging by its name; on this board the G3S rails come up after P5VG3S_EN in the boot sequence. The only known-good reading here is a diode value of 0.423 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.423 usually points to a short or a leaky part on the rail, while a far higher or open reading points to a broken connection or missing part; confirm with a second measurement before replacing anything.

PP5V_G3S_TPAD_CONN0.4147––
AI: what PP5V_G3S_TPAD_CONN is and how to check it
  • What it is: PP5V_G3S_TPAD_CONN is the 5 V rail feeding the trackpad connector, from the name. The G3S stage in this board's sequence is the always-on group, so it should be present early, before the S5/S3/S0 rails.
  • Known-good reading: diode 0.4147 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a damaged part on the rail; an open reading points to a missing feed or enable. Confirm with a second measurement before replacing anything.
PP5V_G3S_VCCIOPVCC0.431––
AI: what PP5V_G3S_VCCIOPVCC is and how to check it

PP5V_G3S_VCCIOPVCC — reference note

  • From its name, this is a 5 V rail in the G3S (always-on) group, feeding VCCIO power for the CPU/PCH I/O domain. The name alone doesn't confirm which parts it supplies.
  • Known-good reading: diode 0.431 to ground (community value, guide only). No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then apply power and measure the voltage.
  • A diode reading far from 0.431 suggests a short or open on that net, but one reading isn't proof — compare with a matching rail or a known-good board before replacing anything.
PP5V_G3S_VCCIOVCC0.429––
AI: what PP5V_G3S_VCCIOVCC is and how to check it

PP5V_G3S_VCCIOVCC is a 5 V rail in the G3S (always-on) group, judging by its name, and the VCCIOVCC suffix suggests it feeds I/O supply. The archive lists one known-good diode reading of 0.429 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, black probe on ground, red on the rail, then measure the voltage with power applied. A diode reading far below 0.429 usually points to a short or a leaky part on that rail; a much higher one can mean an open path, but confirm with a second reading before suspecting a part.

PPBUS_G3H0.47412.600–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main bus rail; the "G3H" suffix means it is always-on (from the name), so it should be present whenever the board has a valid external PSU or battery, before the later switched rails come up.

  • Known-good readings in the archive: diode 0.474 to ground, voltage 12.600. These are community figures and a guide only, not a guaranteed value.
  • To check: power off and disconnect the PSU/battery, then measure diode mode from PPBUS_G3H to ground. Then apply power and measure the voltage on the rail.
  • A diode reading far from 0.474 usually points to a short or a leaky component on the bus; a voltage well off 12.6 with a normal diode reading points more toward the charging/input side not driving the bus.
  • No known-good resistance reading is recorded for this rail, so compare against a matching rail or a known-good board if you need one.
PPBUS_G3H_SPKRAMP_LEFT0.47512.600–
AI: what PPBUS_G3H_SPKRAMP_LEFT is and how to check it

A short reference note on PPBUS_G3H_SPKRAMP_LEFT (820-01598):

  • What it is: from the name, a G3H ("always on") bus rail feeding the left speaker amplifier. The exact parts on it aren't documented here.
  • Known-good readings (community guide): diode 0.475 to ground, voltage 12.600. No known-good resistance value here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading or a missing/incorrect voltage usually points to a short or a failed feed on that rail, but one reading alone doesn't confirm a bad part — compare with the right-channel counterpart if one exists.
PPBUS_G3H_SPKRAMP_RIGHT0.47112.600–
AI: what PPBUS_G3H_SPKRAMP_RIGHT is and how to check it

Reference note for PPBUS_G3H_SPKRAMP_RIGHT on 820-01598:

  • From the name, this is a PPBUS rail feeding the right speaker amplifier; the G3H part indicates an always-on rail in the startup sequence.
  • Known-good readings in the archive: diode 0.471 and voltage 12.600. These are community values and vary with board state, so treat them as a guide only.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied.
  • A diode reading far below 0.471 suggests a short or leaky load on the rail; a far higher one suggests an open path. Confirm with the voltage before replacing anything.
PPBUS_G3H_SSD00.47412.600–
AI: what PPBUS_G3H_SSD0 is and how to check it

PPBUS_G3H_SSD0 is the main bus feeding the SSD section; the G3H part of the name indicates an always-on rail (from the name). The archive lists a known-good diode reading of 0.474 and a voltage of 12.600, with no condition noted, so treat them as a guide.

  • Check it unpowered: diode mode from the rail to ground, board off and discharged.
  • Then power the board and measure the voltage on the rail.
  • A diode reading far below 0.474 usually points to a short or a leaky part on that rail; a much higher or open reading points to a broken feed or a missing connection. A voltage well off 12.600 suggests the bus supply or its enable isn't coming up.
  • No known-good resistance reading is listed here.
PPDCIN_G3H0.56020.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main external DC input rail, and the G3H suffix (from the name) marks it as an always-on rail present whenever a valid charger is connected. The archive lists a known-good diode reading of 0.560 to ground and 20.000 V with power applied; these are community figures and a guide only.

  • Check it unpowered in diode mode from PPDCIN_G3H to ground, then measure the voltage with a valid charger connected.
  • A shorted or very low diode reading points to a fault on the input path itself; a correct diode reading with no 20 V present points upstream, toward the charger/PSU handshake and input sensing.
  • No known-good resistance reading is recorded here, so compare against a matching input net or a known-good board if you need one.
PPDCIN_G3H_CHGR0.55920.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the "G3H" part of the name indicates it is always-on (from the name). Known-good readings in the archive are diode 0.559 and voltage 20.000 V, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then with a valid charger connected measure the voltage. A diode reading far from 0.559 usually points to a short or leaky component on that rail, while a missing 20 V suggests the charger input path is not passing power; there is no known-good resistance reading here to compare against.

PPDCIN_XA_G3H_F0.56020.000–
AI: what PPDCIN_XA_G3H_F is and how to check it

PPDCIN_XA_G3H_F — reference note

  • From its name, this is a DC-input rail in the G3H (always-on) domain: it should be present whenever a valid external supply or battery is connected, before any switched rails come up.
  • Known-good readings from the archive: diode 0.560 to ground, and 20.000 V with power applied. These are community values and a guide only; no known-good resistance reading here.
  • Check it with the board unpowered and discharged: diode mode, red probe on ground, black on the rail, and compare with 0.560. Then apply power and measure the voltage against 20.000 V.
  • A diode reading far below 0.560 suggests a short or leaky load on the rail; a much higher or open reading suggests a broken path or open component. A missing or low voltage with a normal diode reading points upstream, toward the input supply path rather than the rail itself.
PPDCIN_XB_G3H_F0.56020.000–
AI: what PPDCIN_XB_G3H_F is and how to check it

PPDCIN_XB_G3H_F is an always-on G3H-stage rail, judging from its name; it's an early input-side rail in the boot sequence, before the RTC and 3V3 G3H rails. Known-good from the archive: diode 0.560 to ground and 20.000 V with power applied. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A diode reading far below 0.560 suggests a short or leaky load on the rail; a voltage well off 20.000 V points upstream to the input supply or its switching path. No known-good resistance reading is recorded for this rail.

PPVBAT_G3H_CHGR_R0.474––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — the name indicates a battery/charger-related rail in the G3H (always-on) domain, so it should be present whenever a valid external PSU, battery or charger is connected, before the main power sequence starts.

  • Known-good reading: diode 0.474 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If a diode reading is far from 0.474: that usually points to a short or an open on that net or a part on it, but one reading isn't proof — compare with a matching net or a known-good board before replacing anything.
PPVBAT_G3H_CHGR_REG0.47412.600–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG — the name indicates a battery/charger-derived G3H rail (G3H = always-on, from the name), likely the charger's regulated battery input on this 820-01598.

  • Known-good readings from the archive: diode 0.474 to ground, voltage 12.600 V. These are community values and a guide only; no condition is recorded.
  • Check it unpowered in diode mode to ground first, then measure the voltage with a valid PSU or battery connected.
  • A diode reading far below 0.474 suggests a short or leaky part on the rail; a voltage well off 12.600 V points to the charger input or the rail's source not coming up.
  • No known-good resistance reading exists for this rail.
PPVBAT_G3H_CONN1.561––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN — the name indicates the battery (VBAT) connection rail in the G3H "always on" domain, so it's the battery-side feed that should be present whenever a battery or charger is attached, before any switched rails come up.

  • Known-good reading in the archive: diode mode to ground 1.561 (no condition recorded).
  • Check it with the board unpowered and battery/charger disconnected: meter in diode mode, black probe on ground, red on the rail. Then apply power and measure the voltage on the rail.
  • No known-good voltage is recorded for this rail, so compare against a matching battery-connector net or a known-good board of the same model.
  • A diode reading far below 1.561 usually points to a short or a leaky part on the rail; far above it suggests an open connection or a missing path back to the battery connector. Treat the archive value as a guide only, since readings vary with board state.
PPVIN_G3H_P3V3G3H0.47412.600–
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H is an always-on G3H rail, judging by its name, and the "P3V3G3H" part suggests it feeds the 3.3 V G3H supply. The archive lists a known-good diode reading of 0.474 and a voltage of 12.600; no condition is recorded for either, so treat them as a guide only. With the board unpowered, measure diode mode from the rail to ground and compare with 0.474; then power up and check the voltage against 12.600. A diode reading far below known-good usually points to a short or a failing load on the rail, while a missing or low voltage with power applied points to the supply feeding it or an enable problem. There is no known-good resistance value for this rail in the data.

PPVIN_G3H_P3V3G3HRTC0.47412.600–
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC is an always-on startup rail: the G3H part of the name means it stays up whenever external power (PSU, battery or charger) is present, and it feeds the RTC side of the 3V3 G3H supply. Known-good readings from the archive: diode 0.474 to ground and 12.600 V with power applied. Check it unpowered in diode mode to ground first, then measure the voltage with power applied. A diode reading far from 0.474 usually points to a short or a leaky part on that net, while a low or missing voltage points upstream toward the input supply. No known-good resistance reading here, so compare against a matching net or a known-good board.

PPVIN_G3H_P3V3G3HRTC_R0.473––
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it
  • What it is: From its name, this is the input side of the always-on G3H rail feeding the RTC 3.3 V supply. It sits at the very start of the boot sequence, before PP3V3_G3H_RTC and PP3V3_G3H.
  • Known-good reading: Diode mode to ground, board unpowered, is 0.473. No known-good voltage reading here.
  • How to check: Power off and measure diode to ground on the rail, then apply power and measure the voltage. Compare the diode reading with 0.473.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. One reading alone doesn't confirm a bad part, so check the voltage next.
PPVIN_G3H_P5VG3S0.47412.600–
AI: what PPVIN_G3H_P5VG3S is and how to check it

PPVIN_G3H_P5VG3S — the name indicates the input feed for the P5VG3S rail, part of the always-on G3H group (from the name). It appears in the boot sequence just before P5VG3S_EN and PP5V_G3S, so it's the supply that the 5V G3S rail is switched from.

  • Known-good readings in the archive: diode 0.474 and voltage 12.600. No condition is recorded with them, so treat them as a guide only.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Then apply power and measure the voltage.
  • A diode reading far below 0.474 usually points to a short or a leaky part on that rail; a much higher or open reading points to a broken feed or a missing part. The voltage should sit near 12.6 V — a large drop suggests the supply or its input path is loaded down.
  • No known-good resistance value is recorded here, so compare against a matching net or a known-good board.

S5 and SUS: standby 5

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V05_S5_PCH_VCCDSW0.482––
AI: what PP1V05_S5_PCH_VCCDSW is and how to check it
  • What it is: PP1V05_S5_PCH_VCCDSW is a 1.05 V PCH supply in the S5 standby stage, judging from its name (1V05 = 1.05 V, S5 = standby, PCH = chipset, VCCDSW = a PCH well supply). The S5/SUS stage means it should be present while the board is in standby, before the main rails come up.
  • Known-good reading: diode 0.482 in diode mode to ground, board unpowered. There is no known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.482; then power up and measure the voltage on the rail, expecting around 1.05 V from the name (general, not from this board's data).
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a missing voltage with a normal diode reading points upstream, to the rail's enable or source supply. Treat any single reading as a guide, not proof of a bad part.
PP1V8_S50.3031––
AI: what PP1V8_S5 is and how to check it

PP1V8_S5 is a 1.8 V rail in the S5 (standby) domain — that's from the name, and the boot sequence places it in the SSD power-button-monitoring stage after PP3V3_S5, alongside PPVPCORE_S5 and PP1V_PRIM.

  • Known-good: diode-to-ground 0.3031 (community archive, guide only). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail; then power up and measure the voltage.
  • A diode reading far from 0.3031 usually points to a short or a damaged component on that rail; a missing voltage with a good diode reading points upstream, at PP3V3_S5 or the enable for this rail.
PP1V24_S5_PCH_VCCDPHY0.435––
AI: what PP1V24_S5_PCH_VCCDPHY is and how to check it

PP1V24_S5_PCH_VCCDPHY is a 1.24 V rail for the PCH's display PHY (VCCDPHY); the S5 in the name marks it as a standby-stage rail, active in S5 before the main rails come up. The archive lists one known-good reading: diode 0.435 to ground. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage, which should sit near its 1.24 V nominal (general expectation from the name, not an archived value). No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.435 usually points to a short or leaky part on the rail; a far higher or open reading suggests a broken trace or missing component.

PP3V3_S50.3620––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail that comes up in the S5/SUS standby stage, judging from its name. The only known-good figure here is a diode reading of 0.3620 to ground; no known-good voltage is listed.

  • With the board unpowered, measure diode mode from PP3V3_S5 to ground and compare with 0.3620.
  • Then power the board and check the voltage on the rail, comparing against a known-good board since no voltage value is recorded.
  • A diode reading far below 0.3620 usually points to a short or leaky load on the rail; a much higher or open reading points to a broken connection. Confirm with a second measurement before replacing anything.
PPVPCORE_S50.304––
AI: what PPVPCORE_S5 is and how to check it
  • What it is: PPVPCORE_S5 is a standby-stage rail, from its name (S5/SUS = standby). It appears in the boot sequence just after PP3V3_S5 and PP1V8_S5, as the SSD begins power-button monitoring.
  • Known-good reading: diode 0.304 to ground, from the community archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PPVPCORE_S5 to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.304 suggests a short or a leaky load on the rail; well above it suggests an open path. Confirm with a second reading before suspecting a part.

S4 19

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP_SSD0_S4E0_VPP0.632OL Without%2bNand%2b––
AI: what PP_SSD0_S4E0_VPP is and how to check it
  • What it is: PP_SSD0_S4E0_VPP is an SSD-related rail in the S4 startup stage, judging by its name (SSD0, S4E0, VPP — VPP usually means a programming/high-voltage supply for NAND flash, general knowledge, not from this board's data).
  • Known-good readings: diode 0.632 to ground, and diode OL in the "Without Nand" condition — both are community guides, not guaranteed values.
  • How to check: power off, then diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading or a dead short usually points to a shorted part on that rail, but one reading isn't proof — compare against a matching net or a known-good board before replacing anything. No known-good voltage reading is recorded here.
PP_SSD0_S4E1_VPP0.634OL Without+Nand+––
AI: what PP_SSD0_S4E1_VPP is and how to check it

PP_SSD0_S4E1_VPP — the name marks it as an SSD rail in the S4 startup stage; "VPP" in general terms is the NAND program/erase supply, so treat it as a rail that must come up for the SSD to work. Known-good readings here are diode 0.634 to ground, and diode OL on a board without the NAND fitted (condition: Without+Nand+). Check it unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied; no known-good voltage is recorded here. A diode reading well below 0.634 suggests a short or leaky load on the rail, while an open reading on a populated board points to a missing connection rather than a short. These are community readings and only a guide, so compare against a matching net or a known-good board before condemning anything.

PP_SSD0_S4E2_VPPOL––
AI: what PP_SSD0_S4E2_VPP is and how to check it

PP_SSD0_S4E2_VPP is an SSD-related rail; the "S4E2" and "VPP" parts of the name suggest an S4 startup-stage supply, and VPP usually means a programming/high-voltage rail for the SSD's NAND, but that's from the name only, not confirmed here. The only known-good reading in the archive is diode OL to ground, with no stated condition. Check it unpowered in diode mode to ground first, then measure its voltage with power applied during the SSD power-up stage; no known-good voltage reading exists here. A diode reading far below OL would suggest a short or leaky load on that rail, but one reading isn't proof a part is bad.

PP_SSD0_S4E3_VPPOL––
AI: what PP_SSD0_S4E3_VPP is and how to check it

PP_SSD0_S4E3_VPP is an SSD-related rail; the "S4" in its name places it in the S4 startup stage, and "VPP" usually means a programming/high-voltage supply for the NAND (that part is general naming, not from this board's data). The only archived reading is diode mode to ground: OL, with no condition recorded. Check it with the board unpowered in diode mode from the net to ground, then measure its voltage with power applied during the SSD power-up stage. No known-good voltage reading exists here, so compare against a known-good board of the same model. A diode reading far from OL would suggest a short or leaky load on that rail, but one reading alone doesn't confirm a bad part.

PP0V9_SSD0_S4E0_VDD_PLL0.4500.530 Without%2bNand%2b––
AI: what PP0V9_SSD0_S4E0_VDD_PLL is and how to check it

PP0V9_SSD0_S4E0_VDD_PLL is a 0.9 V PLL supply for the SSD section; the S4 in the name marks it as an S4-stage rail, and the rest of the name is from the name only, since no parts list is available.

  • Known-good diode readings to ground: 0.450, and 0.530 with the condition "Without Nand" (NAND not fitted). These are community readings and only a guide.
  • Check with the board unpowered: diode mode from the rail to ground and compare with those two figures. Then apply power and measure the voltage, expecting about 0.9 V once the S4 stage is reached.
  • No known-good voltage reading here, so compare against a matching rail or a known-good board.
  • A diode reading far below known-good usually points to a short or a leaky part on the rail; far above can mean an open feed. Confirm with voltage and resistance before replacing anything.
PP0V9_SSD0_S4E1_VDD_PLL0.4500.520 Without+Nand+––
AI: what PP0V9_SSD0_S4E1_VDD_PLL is and how to check it

PP0V9_SSD0_S4E1_VDD_PLL is a 0.9 V SSD rail, most likely the PLL supply for the SSD controller; that reading comes from the name, and the S4 in it places it in the S4 startup stage. Known-good readings here are diode 0.450, and 0.520 with the condition "Without+Nand+". Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and the SSD powered up. A reading far from known-good usually points to a short or a missing supply on that rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is recorded for this rail.

PP0V9_SSD0_S4E2_VDD_PLLOL––
AI: what PP0V9_SSD0_S4E2_VDD_PLL is and how to check it

PP0V9_SSD0_S4E2_VDD_PLL is a 0.9 V SSD PLL supply; the "S4" in the name puts it in the S4 startup stage, and the "SSD0" part ties it to the SSD power-up sequence (general reading of the name, not from board data). The only known-good reading here is a diode value of OL to ground, with no condition stated. Check it unpowered in diode mode, red probe on ground and black on the net, then confirm the voltage with power applied; no known-good voltage reading exists here. A diode reading far below OL suggests a short or leaky load on the rail, but one reading alone doesn't prove a part bad, so compare against a matching net or a known-good board before replacing anything.

PP0V9_SSD0_S4E3_VDD_PLLOL––
AI: what PP0V9_SSD0_S4E3_VDD_PLL is and how to check it

PP0V9_SSD0_S4E3_VDD_PLL is a 0.9 V PLL supply for the SSD section, judged from its name; the S4E3 suffix suggests it belongs to the S4/S3-era part of the sequence. In the readings archive its only known-good reading is a diode value of OL to ground, so there is no known-good voltage here. Check it unpowered in diode mode from the net to ground, then measure the voltage with the board powered and compare against a matching 0.9 V SSD rail or a known-good board. A diode reading far below OL suggests a short or leaky load on the rail; a missing voltage points to its enable or source, not necessarily the rail itself.

PP1V8_SSD0_S4E0_AVDD18_PLL0.3480.520 Without%2bNand%2b––
AI: what PP1V8_SSD0_S4E0_AVDD18_PLL is and how to check it
  • What it is: From the name, a 1.8 V rail feeding the SSD's PLL/AVDD18 supply, in the S4 stage of the boot sequence (the SSD power-up steps). The name doesn't confirm which parts sit on it.
  • Known-good readings: diode 0.348, and 0.520 with the condition "Without Nand" (SSD NAND not fitted). These are community values and a guide only; no known-good voltage reading here.
  • How to check: Power off, then diode mode from the rail to ground. Then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail; a missing voltage points back to the SSD power-up sequence that enables it.
PP1V8_SSD0_S4E0_PCI_AVDD_H0.3480.520 Without%2bNand%2b––
AI: what PP1V8_SSD0_S4E0_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail feeding the SSD's PCIe/AVDD domain, in the S4 startup stage. The board data only lists the net and its readings; it doesn't show which parts sit on it.
  • Known-good (guide only): diode 0.348 to ground, and 0.520 with the note "Without Nand" (NAND removed). Community readings vary with board state.
  • How to check: power off, discharge, then diode mode from the net to ground; then power on and measure the voltage. No known-good voltage reading is recorded here.
  • If far off: a much lower diode reading usually points to a short or a damaged part on the rail; a much higher one to an open. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E1_AVDD18_PLL0.3480.520 Without+Nand+––
AI: what PP1V8_SSD0_S4E1_AVDD18_PLL is and how to check it

PP1V8_SSD0_S4E1_AVDD18_PLL — reference note

  • From its name, this is a 1.8 V rail feeding the SSD's PLL/AVDD18 supply, active in the S4 stage of the boot sequence (the SSD landing phase).
  • Known-good readings from the archive: diode mode to ground 0.348, and 0.520 with the NAND removed ("Without+Nand+"). These are community values and vary with board state, so treat them as a guide.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage at the rail.
  • No known-good voltage reading is recorded here. A diode reading far below 0.348 suggests a short or leaky load on the rail; a reading far above it suggests an open path. Confirm with a voltage measurement before replacing anything.
PP1V8_SSD0_S4E1_PCI_AVDD_H0.3480.510 Without+Nand+––
AI: what PP1V8_SSD0_S4E1_PCI_AVDD_H is and how to check it
  • What it is: From the name, a 1.8 V SSD-related PCIe/AVDD supply that comes up in the S4 stage of the startup sequence. The archive lists no parts on this net.
  • Known-good readings (community, guide only): diode 0.348, and diode 0.510 with "Without+Nand+" (SSD NAND not fitted). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the net to ground; then power on and measure the voltage. Compare the diode reading against the matching condition (NAND fitted or not).
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail, but one reading doesn't confirm a bad part. Next, check the rail's enable and the SSD power sequence around it.
PP1V8_SSD0_S4E2_AVDD18_PLLOL––
AI: what PP1V8_SSD0_S4E2_AVDD18_PLL is and how to check it
  • What it is: From its name, a 1.8 V rail feeding the SSD's PLL analog supply, in the S4 startup stage. The board data doesn't list which parts sit on it.
  • Known-good readings: The archive only has a diode reading of OL for this net. There is no known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with the archived OL. Then apply power and measure the voltage on the rail.
  • What a far-off reading suggests: A diode value well below OL, or a missing or wrong voltage once the SSD rails are up, points to a short, a failed supply or a part on the rail — a likely cause, not a confirmed one.
PP1V8_SSD0_S4E2_PCI_AVDD_HOL––
AI: what PP1V8_SSD0_S4E2_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail feeding the SSD's PCIe/AVDD side, enabled in the S4 startup stage. The archive has no part list, so which components sit on it isn't known.
  • Known-good readings: diode OL is the only archived value for this net; there is no known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the net to ground; then power up and measure the voltage on the net.
  • If it reads far from known-good: a short or near-zero diode reading points to a fault on the rail or its load; an open (OL) with no voltage present usually means the rail isn't being enabled or its source isn't switching. Confirm with the enable and upstream rail before replacing anything.
PP1V8_SSD0_S4E3_AVDD18_PLLOL––
AI: what PP1V8_SSD0_S4E3_AVDD18_PLL is and how to check it
  • What it is: From its name, a 1.8 V rail feeding the SSD's PLL (AVDD18) in the S4 state. The name also places it at the S4 startup stage.
  • Known-good readings: The archive lists only a diode reading of OL for this net. There is no known-good voltage or resistance value here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with the OL entry. Then power up and measure the voltage on the rail.
  • What a far-off reading suggests: A short or low diode reading where OL is expected points to a fault on the rail or its load. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E3_PCI_AVDD_HOL––
AI: what PP1V8_SSD0_S4E3_PCI_AVDD_H is and how to check it
  • What it is: From the name, a 1.8 V rail feeding SSD0 and PCIe AVDD, in the S4 state. The name is the only description available; which parts sit on it isn't known.
  • Known-good readings: The archive lists diode OL for this net. That is the only value recorded, so there is no known-good voltage here.
  • How to check: Power off and unplug, then diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • What a far-off reading suggests: A short or a missing enable on the rail. Compare against a matching net on the other side of a pair before condemning anything.
PP3V3_S4SW_SNS0.560––
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V switch-mode rail in the S4 stage of the power sequence, judging by its name (S4 = the S4 sleep-state stage; SW = switch-mode; SNS = sense). The archive lists a known-good diode reading of 0.560 to ground, with no condition noted, and no known-good voltage reading here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail; compare with 0.560.
  • Then power the board and measure the voltage on the rail; the archive gives no expected voltage, so compare with a known-good board or the matching rail elsewhere.
  • A diode reading far below 0.560 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection or missing part. Neither confirms a bad part on one reading.
  • Power off before diode or resistance checks.
PP5V_S4SWOL––
AI: what PP5V_S4SW is and how to check it

PP5V_S4SW is a 5 V switched rail in the S4 startup stage, judging from its name (S4 = the S4 sleep/startup state, SW = switched). The only archived reading for it is a diode-mode value of OL to ground; there is no known-good voltage or resistance reading here.

  • With the board unpowered, measure diode mode from PP5V_S4SW to ground and compare with that OL guide.
  • Then apply power and measure the voltage on the rail.
  • OL in diode mode can be normal for a switched rail that is off, so a voltage check with the board in the right state matters more.
  • A voltage far below expected usually points to the rail not being enabled or its source/switch not turning on; confirm the enable and upstream supply before suspecting a part.
PPVIN_S4_TPAD_FUSE0.3344––
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE is a fused input rail feeding the trackpad section, in the S4 power stage — that reading comes from the rail's name, not from a schematic. The only known-good figure here is a diode reading of 0.3344 to ground; no known-good voltage is recorded for this rail.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.3344.
  • Then power the board and measure the voltage on the rail; there is no known-good voltage here, so compare against the same rail on a known-good board or the upstream source feeding it.
  • A diode reading far below 0.3344 usually points to a short or a leaky part on that rail; a much higher or open reading points to a broken trace or fuse. A single reading isn't proof, so confirm before replacing anything.

S3: memory 9

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.378––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it
  • What it is: From its name, a 0.6 V memory reference rail that comes up in the S3 (suspend-to-RAM) stage; the boot sequence lists S3 as the memory stage. The exact parts on the net aren't known here.
  • Known-good reading: diode 0.378 to ground, from the community archive — a guide only, since readings vary with board state. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the DC voltage on the rail.
  • If it's far off: a diode reading well below known-good usually points to a short or a leaky part on the rail; a missing or wrong voltage with a normal diode reading points more to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.378––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a memory reference rail: the "0V6" and "VREFDQ" in the name indicate a 0.6 V DDR data-reference voltage, and "S3" places it in the memory stage of the boot sequence. The only known-good reading here is a diode value of 0.378; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage at the rail. A diode reading far from 0.378 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare against a matching reference net or a known-good board before replacing anything.

PP0V6_S3_MEM_VREFDQ_B0.380––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail that comes up in the S3 (suspend-to-RAM) stage; that stage and the memory role come from the rail's name, not from a schematic. The archive lists one known-good reading: diode 0.380 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage; no known-good voltage reading exists here, so compare against a matching reference net or a known-good board. A diode reading far from 0.380 usually points to a short or a leaky part on that net, but one reading alone isn't proof, so confirm with a second measurement before replacing anything.

PP1V_S30.248––
AI: what PP1V_S3 is and how to check it

PP1V_S3 is a 1 V rail in the S3 (suspend-to-memory) state; the S3 meaning comes from the rail's name, and the boot sequence places it after PP1V2_S3 and PVDDQ_PGOOD, before the PCH releases SLP_S3#. The only known-good reading recorded is a diode value of 0.248 to ground (condition not stated), so treat it as a guide; there is no known-good voltage or resistance value here. Check it unpowered in diode mode to ground, then power the board and measure the DC voltage while it is in S3. A diode reading far from 0.248 suggests a short or leaky load on the rail, but one reading alone doesn't confirm a bad part — compare against a matching rail or a known-good board before replacing anything.

PP1V2_S30.2191.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail in the S3 (memory) startup stage, judged from its name; it appears in the boot sequence after PP1V8_S3 and PVDDQ_EN, alongside PVDDQ_PGOOD and PP1V_S3.

Known-good readings from the archive: diode 0.219 to ground and voltage 1.200 V. No condition is recorded for either, so treat them as a guide only.

To check it: power off and measure diode mode from PP1V2_S3 to ground, then apply power and measure the voltage. A diode far from 0.219 suggests a short or leaky load on the rail; correct voltage but no boot points further along the sequence, toward PVDDQ_PGOOD and PP1V_S3. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP1V2_S3_CPUDDR0.221––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is a 1.2 V memory rail that comes up in the S3 stage, judging by its name (S3 = memory stage in the boot sequence). The only known-good reading in the archive is a diode value of 0.221; there is no known-good voltage or resistance value here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.221, then apply power and check the rail voltage. A diode reading far from 0.221 usually points to a short or a damaged component on that rail, but confirm with the voltage reading before replacing anything.

PP1V2_S3_REG_R0.2201.200–
AI: what PP1V2_S3_REG_R is and how to check it
  • What it is: PP1V2_S3_REG_R is a 1.2 V rail in the S3 (memory) startup stage, judging by its name; the board data doesn't list which parts sit on it.
  • Known-good readings: diode 0.220 and voltage 1.200, from the readings archive and a guide only, since readings vary with board state.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading usually points to a short or a failing load on the rail, while a missing or wrong voltage points to the regulator or its enable. No known-good resistance reading exists here; compare with a matching rail or a known-good board.
PP1V8_S30.479––
PP1V8_S3_MEM0.479––
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM is a 1.8 V memory rail that comes up in the S3 stage, judged from its name; the boot sequence lists PP1V8_S3 and PP1V_S3 around the S3 step, so it belongs to the memory power group. The only known-good reading here is diode 0.479 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage reading exists here. A diode value far from 0.479 can suggest a short or an open on that net, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

S0: running 26

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.153––
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT — from the name, a 0.6 V DDR termination rail that comes up in the S0 (running) state. Its known-good reading in the archive is diode 0.153; no known-good voltage or resistance reading is recorded here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.153.
  • Then power the board and measure the voltage; it should sit near 0.6 V once the board is running (general expectation from the rail name, not from this board's data).
  • A diode reading far from 0.153 usually points to a short or a leaky part on the rail; a missing or wrong voltage with a normal diode reading points more to the rail's supply or enable.
PP0V95_S0_CPUVCCIO_REG_R0.1360.950134.800
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it

PP0V95_S0_CPUVCCIO_REG_R — the name indicates a CPU VCCIO supply rail (general naming convention, not from board data), and the S0 suffix places it in the running state, after S3/S0 rails come up.

  • Known-good readings from the archive: diode 0.136, voltage 0.950 V, resistance 134.8 Ω. These are community values and only a guide.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Then power up and measure the voltage.
  • A voltage well off 0.950 V, or a diode/resistance far from these, usually points to a short or a failed regulator feeding the rail — but one reading alone doesn't confirm a bad part.
PP1V_S0SW0.237––
AI: what PP1V_S0SW is and how to check it

PP1V_S0SW is a 1 V rail in the S0 (running) state, judged from its name; the boot sequence lists it as enabled after the PCH de-asserts SLP_S3# and alongside PP1V2_S0SW, PVCCIO and ALL_SYS_PWRGD.

  • Known-good: diode reading 0.237 to ground (community archive, condition not stated). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe to ground, black to the rail, and compare with 0.237.
  • Then apply power and measure the voltage; no known-good voltage is listed, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far from 0.237 suggests a short or open on that rail, but one reading alone doesn't confirm a bad part; verify before replacing anything.
PP1V2_S0SW0.291––
AI: what PP1V2_S0SW is and how to check it

PP1V2_S0SW is a 1.2 V rail that comes up in the S0 (running) state, judging from its name and its place in the boot sequence after SLP_S3# is released. The archive lists one known-good reading: diode 0.291 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied once the board reaches S0. No known-good voltage reading is recorded here, so compare against a matching S0 rail or a known-good board. A diode reading far below 0.291 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP1V8_S0_THMSNSA_R0.343––
AI: what PP1V8_S0_THMSNSA_R is and how to check it

PP1V8_S0_THMSNSA_R — reference note

  • What it is: a 1.8 V rail, from the name. The "S0" suffix places it in the running (S0) state, so it belongs to the later part of the boot sequence, after the S3/S5 rails in the sequence above. The "THMSNSA" part of the name isn't explained in the available data, so its exact function on this board is unknown.
  • Known-good reading: diode 0.343 to ground, from the community archive. No known-good voltage reading is available here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.343. Then apply power and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.343 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken trace or missing connection. A missing or low voltage with a normal diode reading points upstream, to the rail's enable or source. These are likely causes only, not confirmed ones.
PP1V8_S0_THMSNSB_R0.344––
AI: what PP1V8_S0_THMSNSB_R is and how to check it

PP1V8_S0_THMSNSB_R is a 1.8 V rail that, from its name, runs in the S0 (running) state and is a thermal-sensor-related supply ("THMSNSB"). The only known-good reading here is a diode value of 0.344 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered: board off and unplugged, meter in diode mode, black probe on ground, red on the rail, and compare with 0.344.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is listed, so compare against a known-good board or a matching rail.
  • A diode reading far below 0.344 suggests a short or leaky load on the rail; far above it suggests an open path. Either way, confirm with the voltage measurement before replacing anything.
PP3V3_S0_TBT_X_ISNS_R0.530––
AI: what PP3V3_S0_TBT_X_ISNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail tied to Thunderbolt current sense ("ISNS"). The board data doesn't name the parts on it.
  • Known-good: diode 0.530 to ground (community reading, a guide only). No known-good voltage reading here.
  • Check: power off, diode mode, black probe to ground, red on the rail; then power on and measure the voltage.
  • Far off known-good: usually a short or a faulty load on that rail, but one reading isn't proof — compare with a matching net or a known-good board before replacing anything.
PP3V3_S0SW_LCD0.4757––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a 3.3 V switched LCD rail. From the name: S0 means it belongs to the running (S0) state, SW that it is switched on by a control signal, and LCD that it feeds the display side. It appears late in the boot sequence, after the S0 rails come up.

  • Known-good reading in the archive: diode 0.4757 (board unpowered, diode mode to ground). No known-good voltage reading is recorded here.
  • Check it with power off and the battery/charger disconnected: diode mode, red probe to ground, black to the rail. Then power up and measure the DC voltage on the rail.
  • A diode reading far from 0.4757 usually points to a short or a leaky part on that rail; a correct diode reading but no voltage points more to the switch or its enable signal. Treat these as guides, not confirmed faults.
PP3V3_S0SW_LCD_R0.478––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is a 3.3 V LCD-related rail that switches in the S0 (running) state, judging from its name; the exact parts it feeds aren't documented here. The only known-good reading in the archive is a diode value of 0.478 to ground, with no condition noted and no known-good voltage listed. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.478 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken feed or enable. Treat the 0.478 as a community guide only, and confirm a suspect rail against a matching net or a known-good board before replacing anything.

PP3V3_TBT_X_S00.530––
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt section, and the _S0 suffix from its name means it belongs to the running (S0) state. The archive lists a known-good diode reading of 0.530 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.530, then apply power and check for about 3.3 V once the board is in S0. A diode reading far below 0.530 suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points more to the enable or upstream supply. These are community readings and vary with board state, so treat them as a guide.

PP5V_S0_BKLT_A0.424––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the 5 V backlight rail that comes up in the S0 (running) state, judging by its name; it feeds the display backlight. The only known-good reading here is a diode-mode value of 0.424 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on it. No known-good voltage reading is recorded here, so compare against a matching backlight rail or a known-good board of the same model. A diode reading far below 0.424 usually points to a short or leaky component on the rail, while a much higher one suggests an open path; confirm with the voltage measurement before replacing anything.

PP5V_S0_BKLT_D0.423––
PP5V_S0SW_LCD0.576––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD — reference note

  • This is a 5 V LCD-related rail that switches on at the S0 (running) stage, judging from the name; the board data lists it only as a net with a diode reading, not which parts sit on it.
  • Known-good: diode-to-ground 0.576 (community reading, a guide only; board state affects it). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe to ground, red to the rail. Then power up and measure the voltage at the rail.
  • A diode reading far from 0.576 usually points to a short or a leaky component on that rail; a missing or low voltage with power applied points toward its enable or supply upstream. Confirm with a second measurement before replacing anything.
PP5V_S0SW_LCD_R0.576––
AI: what PP5V_S0SW_LCD_R is and how to check it

PP5V_S0SW_LCD_R is a switched 5 V LCD rail that comes up in the S0 (running) state, judging from its name. The only known-good figure here is a diode reading of 0.576 to ground, with no condition noted; there is no known-good voltage reading for this rail.

  • Check it unpowered: diode mode, black probe to ground, red on the rail, and compare with 0.576.
  • Then power the board and measure the voltage on the rail; the archive gives no expected value, so compare against a known-good board or the panel's supply requirement.
  • A diode reading far below 0.576 usually points to a short or a leaky load on the rail; a much higher one can mean an open path. Either is a guide, not proof of a bad part.
PPVCC_S0_CPU0.0071.5006.400R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the S0 in its name means it belongs to the running (S0) state, so it should come up late in the boot sequence, after the S3 and S0SW rails. The archive lists a known-good diode reading of 0.007 to ground, a voltage of 1.500, and a resistance of 6.400R; treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and running. A diode or resistance far below known-good suggests a short or heavy load on the rail; a missing or low voltage with a normal diode reading points more to the rail not being enabled or its supply failing. No known-good value of another kind is listed here.

PPVCCEDRAM_S0_CPU0.1131.000111.700
AI: what PPVCCEDRAM_S0_CPU is and how to check it

PPVCCEDRAM_S0_CPU — the name indicates a CPU-side eDRAM supply that is up in the S0 (running) state; that reading of the name is general, not from this board's data.

  • Known-good readings here: diode 0.113, voltage 1.000, resistance 111.700. These are community values and only a guide; the data gives no condition for them.
  • To check: power off and unplug, then diode-mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a short or a failing load on the rail; a voltage far off with a normal diode reading points more to the supply or enable side. No known-good current draw or waveform is listed here.
  • One reading alone doesn't condemn a part — confirm with a second measurement before replacing anything.
PPVCCEDRAM_S0_REG_R0.1131.000111.700
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R — reference note

  • What it is: from the name, a switched S0 (running-state) regulated supply for the CPU's embedded DRAM, with the _R suffix marking it a secondary/regulator-derived rail. The boot sequence lists it in the S0 stage, after the S3 rails and around PVCCIO / ALL_SYS_PWRGD.
  • Known-good readings (community archive, guide only): diode 0.113 to ground, voltage 1.000 V, resistance 111.700. No known-good value of another kind is recorded here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power the board and measure the voltage on the rail, ideally at the same point and board state as the archived reading.
  • If far off: a much lower diode or resistance reading suggests a short or leak on the rail; correct voltage with a wrong diode reading is less
PPVCCGT_S0_CPU0.0071.5006.700R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU — from the name, this is the CPU graphics (GT) core rail, active in the S0 running state. It appears late in the boot sequence, after the S0 rails and CPU VR are up.

Known-good readings for this rail: diode 0.007, voltage 1.500 V, resistance 6.700R. These are community readings and only a guide; the data gives no condition for them.

To check it: power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the voltage at the rail.

A diode reading far from 0.007, especially near zero, usually points to a short on the rail; a voltage far from 1.500 V with the board in S0 suggests the rail isn't being enabled or its supply is failing. No known-good reading of other kinds is listed here.

PPVCCIO_S0_CPU0.1360.950134.800
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU — reference note

  • What it is: the CPU's VCCIO rail. The S0 suffix marks it as a running-state rail (from the name), and it appears in the boot sequence after PVCCIO_EN and before PVCCIO_PGOOD and ALL_SYS_PWRGD.
  • Known-good readings (community archive, guide only, no condition recorded): diode 0.136, voltage 0.950 V, resistance 134.8 Ω.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: a diode or resistance well below known-good suggests a short or a leaky load on the rail; a missing or wrong voltage with a normal diode reading points more to the enable side (PVCCIO_EN) or the rail's supply. No known-good value of another kind is recorded here, so compare against a matching rail or a known-good board.
PPVCCSA_S0_CPU0.0371.15036.000R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is a CPU system-agent supply rail; the S0 in its name means it belongs to the running (S0) state, and the CPU suffix marks it as a processor rail. The archive lists diode 0.037, voltage 1.150 V and resistance 36.000R, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S0. A reading far from these values points to a short or a missing rail rather than a confirmed bad part, so compare against a matching rail or a known-good board before replacing anything. No known-good value is listed for any other measurement type here.

PPVIN_S0_CPUVR_VIN0.483––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN — the name indicates it is the input supply to the CPU voltage-regulator stage, active in the S0 (running) state. The archive lists one known-good reading: diode mode to ground 0.483; no known-good voltage reading here.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. Compare with 0.483.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded, so compare against a known-good board or the regulator's expected input.
  • A diode reading far below 0.483 usually points to a short or leaky part on the rail; far above can mean an open path. One reading alone doesn't condemn a part — confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT0.85012.600–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT — the name indicates the backlight input rail for the LCD, active in the S0 (running) state. It is the supply feeding the display backlight circuit, not a logic signal.

Known-good readings from the archive: diode mode to ground 0.850, and 12.600 V with the board powered and running. Treat these as a guide only, since community readings vary with board state.

To check it: power off and unplug, then measure diode mode from the rail to ground; then apply power and measure the voltage in the running state. A diode reading far below 0.850 suggests a short or leaky load on the rail; a voltage well off 12.600 V with power applied points to a supply or enable problem upstream. No known-good resistance reading is recorded for this rail.

PPVIN_S0SW_LCDBKLT_F0.47412.600–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F is the display backlight input rail; the S0SW part of the name indicates it is switched on in the S0 (running) state, and the LCDBKLT part that it feeds the backlight. The archived readings for this board are diode 0.474 and voltage 12.600, which are community values and a guide only. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode reading far below known-good usually points to a short or a leaky component on the rail, while a voltage that is missing or well off 12.600 points to the backlight supply or its enable not coming up; no known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT_R0.47412.600–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it
  • What it is: the LCD backlight input rail, switched in the S0 (running) state — that meaning comes from the name, not from board data.
  • Known-good readings: diode 0.474 to ground and 12.600 V with the board powered and running. These are community readings and only a guide.
  • How to check: with power off and the battery/charger disconnected, measure diode mode from the rail to ground; then power up into S0 and measure the voltage.
  • If it's far off: a much lower diode reading points to a short or leaky load on the rail, while no or low voltage in S0 points to the backlight supply or its enable not coming up. There is no known-good resistance reading here, so compare against a matching rail or a known-good board.
PPVOUT_S0_LCDBKLT1.214046.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the name indicates it belongs to the S0 (running) power state, and this is from the name rather than a schematic.

  • Known-good readings in the archive: diode 1.2140 to ground, voltage 46.000 with the board powered.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the display connected.
  • A diode reading far below 1.2140 usually points to a short or leaky load on the backlight output; a voltage well off 46.000 points to the backlight boost circuit or its enable path.
  • No known-good resistance reading is recorded for this rail.
PPVOUT_S0_LCDBKLT_F1.20546.000–
AI: what PPVOUT_S0_LCDBKLT_F is and how to check it

PPVOUT_S0_LCDBKLT_F is the display backlight boost output; the name (LCD backlight, S0 = running state) suggests it only comes up once the board is in S0. Known-good readings from the community archive: diode 1.205 and voltage 46.000 V, with no condition noted. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and running. A diode reading far from 1.205 points to a short or leak on the backlight output or its boost circuit, and no voltage where 46 V is expected points to the backlight boost not running. No known-good resistance reading here; compare against a matching net or a known-good board.

Repair notes

Power

Boot sequence

* Valid external PSU, bat or charger PBUS PP3V3_G3H_RTC PP3V3_G3H VIN_RTC > VIN_RTC_UPPER_THRESHOLD PP1V8_SLPS2R PMU_CLK32K_SOC PP1V8_AWAKE PP1V8_SLPS2R_PMUGPIO PP1V1_SLPS2R PP0V8_SLPS2R PP0V82_SLPDDR PP3V3_AWAKE PPVDDCPUSRAM_AWAKE PP0V9_SLPDDR PP1V1_SLPDDR_SOCFET_EN PP1V1_SLPDDR H9M_24MHz_CLK PP1V2_AWAKE PPVDDCPU_AWAKE PMU_SYS_ALIVE PMU_ACTIVE_READY PMU_COLD_RESET_L H9M LOAD SECURE ROM, SMC BATTERY TRAP PMU_PVDDMAIN_EN P3V3MAIN_PGOOD PP3V_G3H_RTC PMU_CLK32K_PCH PCH_RTC_RESET_L P5VG3S_EN PP5V_G3S P3V3G3S_EN PP3V3_G3S P1V8G3S_EN PP1V8_G3S P5VG3S_PGOOD PMU_CLK32K_WLANBT SSD 4LANDING: OCARINA I2C WRITE POWER_STATE_TARGET=ACTIVE TO ENABLE SSD POEWR SSD_PMU_RESET_L PPVCCQ_ANI_SSD0 PP0V9_SSD0 SSD0_VR_2V5_EN PP2V5_NAND_SSD0 SSD0_OCARINA_WP_L SSD0_OCARINA_PFN SSD0_PCARINA_RESET_L SSD 2LANDING: CALPE, CONFIGURE RAILS AND GPIOS TO ENABLE SSD POWER PPVCCQ_ANI_SSD0 PP0V9_SSD0 SSD0_PMIC_DISCHARGE_EN SSD0_VR_2V5_EN PP2V5_NAND_SSD0 SSD0_VR_P2V5_PGOOD SSD0_PMIC_RESET_L SSD BEGINS POWER BUTTON MONITORING PMU_ONOFF_L PP3V3_S5 PP1V8_S5 PPVPCORE_S5 PP1V_PRIM SMC_RSMRST_L PM_RSMRST_L SMC WAITS FOR eSPI_RESET# PIN PCH_PWRBTN_L PP1V8_S3 PVDDQ_EN PP1V2_S3 PVDDQ_PGOOD PP1V_S3 PCH DE-ASSERTS SLP_S3#, SLP_A#, SLP_LAN#, and SLP_WLAN# over eSPI PVCCPLLOC_EN PP1V2_S0SW PP1V_S0SW PVCCIO_EN PVCCIO PVCCIO_PGOOD ALL_SYS_PWRGD CPU_VR_READY PM_SYSRST_L PM_PCH_PWROK PM_PCH_SYS_PWROK DONE.

Every net with a reading

NetDiodeVoltageResistance
$NONE$288OL––
$NONE$289OL––
$NONE$290OL––
$NONE$291OL––
$NONE$337OL––
$NONE$338OL––
$NONE$339OL––
$NONE$340OL––
$NONE$341OL––
$NONE$342OL––
$NONE$343OL––
$NONE$387OL––
$NONE$388OL––
$NONE$389OL––
$NONE$390OL––
$NONE$391OL––
1V8_SWCH_ENOL––
1V8_SWCH_SLEWOL––
50_ANT_C0OL––
50_ANT_C1OL––
ACCEL_INT10.487––
ACT_GND0.000––
ADC2_REFCOMPOL––
ALL_SYS_PWRGD0.719––
ALL_SYS_PWRGD_R0.511––
AON_SLEEP1_RESET_L0.432––
AUD_CONN_HP_LEFT0.710––
AUD_CONN_HP_RIGHT0.715––
AUD_CONN_HP_SENSE_L1.300––
AUD_CONN_HP_SENSE_R1.300––
AUD_CONN_RING_SENSE0.6254––
AUD_CONN_RING20.0013––
AUD_CONN_RING2_XW0.6268––
AUD_CONN_SLEEVE0.0013––
AUD_CONN_SLEEVE_XW0.6270––
AUD_CONN_TIP_SENSE1.3625––
AUD_DMIC0_DATA_CONN0.562––
AUD_DMIC1_DATA_CONN0.566––
AUD_HP_PORT_CH_GND0.001––
AUD_HP_PORT_L0.710––
AUD_HP_PORT_R0.715––
AUD_HP_PORT_US_GND0.001––
AUD_HP_SENSE_L1.300––
AUD_HP_SENSE_R1.300––
AUD_HS_MIC_N0.633––
AUD_HS_MIC_P0.633––
AUD_PWR_EN0.783––
AUD_RING_SENSE0.640––
AUD_TIP_SENSE1.460––
BKLT_EN_R0.548––
BKLT_PWM_KEYB0.548––
BKLT_SCL0.543––
BKLT_SD0.597––
BKLT_SDA0.542––
BKLT_SENSE_OUT0.742––
BOARD_REV00.482––
BOARD_REV20.478––
BOOT_CONFIG00.483––
BOOT_CONFIG10.482––
BOOT_CONFIG20.483––
BT_AUDIO_SYNC0.555––
BT_GPIO_40.552––
BT_GPIO_50.550––
BT_PWR_EN0.781––
BT_SFLASH_CS_L0.700––
BT_SFLASH_HOLD_L0.672––
BT_SFLASH_WP_L0.676––
BT_SPI2_CLK0.608––
BT_SPI2_CLK_ROL––
BT_SPI2_CSN0.624––
BT_SPI2_CSN_ROL––
BT_SPI2_MISO0.603––
BT_SPI2_MISO_ROL––
BT_SPI2_MOSI0.611––
BT_SPI2_MOSI_ROL––
CATERR_LED_AOL––
CATERR_LED_GOL––
CATERR_LED_KOL––
CHGR_AMON0.628––
CHGR_AUX_DET0.634––
CHGR_BGATE0.631––
CHGR_BMON0.628––
CHGR_BOOT10.592––
CHGR_BOOT1_RC0.591––
CHGR_BOOT20.588––
CHGR_BOOT2_RC0.587––
CHGR_COMP0.630––
CHGR_CSI_N0.560––
CHGR_CSI_P0.560––
CHGR_CSI_R_N0.55920.000–
CHGR_CSI_R_P0.55920.000–
CHGR_CSO_N0.473––
CHGR_CSO_P0.473––
CHGR_CSO_R_N0.474––
CHGR_CSO_R_P0.474––
CHGR_EN_MVR0.6105,000–
CHGR_EN_MVR_R0.6105,000–
CHGR_GATE_Q10.740––
CHGR_GATE_Q20.463––
CHGR_GATE_Q30.465––
CHGR_GATE_Q40.711––
CHGR_INT_L0.621––
CHGR_LX10.49012.600305.800R
CHGR_LX20.49012.600–
CHGR_RST_IN0.625––
CHGR_RST_IN_R0.690––
CHGR_VBAT0.647––
CHGR_VDDA0.460––
CHGR_VDDP0.459––
CODEC_INT_L0.490––
CODEC_LDO_EN0.786––
CODEC_RESET_L0.487––
CODEC_WAKE_L0.484––
COMP_A_CPUGT0.635––
COMP_A_CPUGT_LOL––
COMP_B_CPUCORE0.635––
COMP_B_CPUCORE_LOL––
COMP_C_CPUSA0.635––
COMP_C_CPUSA_LOL––
CORE_ISUMN_R1.016––
CPU_C10_GATE_L0.755––
CPU_CATERR_L0.258––
CPU_CFG<0>0.2931––
CPU_CFG<1>0.2920––
CPU_CFG<2>0.2924––
CPU_CFG<3>0.2929––
CPU_CFG<4>0.2760––
CPU_CFG<5>0.2929––
CPU_CFG<6>0.2927––
CPU_CFG<7>0.2905––
CPU_CFG<8>0.2909––
CPU_CFG<9>0.2912––
CPU_CFG<10>0.2916––
CPU_CFG<11>0.2932––
CPU_CFG<12>0.2929––
CPU_CFG<13>0.2915––
CPU_CFG<14>0.2932––
CPU_CFG<15>0.2930––
CPU_CFG<16>0.2934––
CPU_CFG<17>0.2946––
CPU_CFG<18>0.2940––
CPU_CFG<19>0.2925––
CPU_DDDR0_ALERT_L0.001–0.300R
CPU_DDDR1_ALERT_L0.001–0.300R
CPU_DIMM_VREFCA0.381––
CPU_DIMMA_VREFDQ0.388––
CPU_DIMMB_VREFDQ0.388––
CPU_IST_TRIG0.357––
CPU_PECI0.471––
CPU_PECI_R0.303––
CPU_PROCHOT_L0.466––
CPU_PROCHOT_OUT_L0.488––
CPU_PROCHOT_R_L0.307––
CPU_VCCEOPIOSENSE_N0.002–1.400R
CPU_VCCEOPIOSENSE_P0.127––
CPU_VCCEOPIOSENSE_XW0.002–1.400R
CPU_VCCGTSENSE_N0.002–1.500R
CPU_VCCGTSENSE_P0.009––
CPU_VCCIOSENSE_N0.001–1.100R
CPU_VCCIOSENSE_P0.134––
CPU_VCCIOSENSE_R0.216––
CPU_VCCIOSENSE_XW0.001–1.300R
CPU_VCCSASENSE_N0.003––
CPU_VCCSASENSE_P0.038––
CPU_VCCSENSE_N0.003––
CPU_VCCSENSE_P0.010––
CPU_VCCST_PWRGD0.526––
CPU_VIDALERT_L0.303––
CPU_VIDSCLK0.257––
CPU_VIDSOUT0.259––
CPU_VR_EN_R0.513––
CPU_VR_PROCHOT_L0.530––
CPU_VR_READY0.608––
CPU_ZVM_L0.402––
CPUCORE_FCCM0.614––
CPUCORE_ISEN10.637––
CPUCORE_ISEN20.637––
CPUCORE_ISNS1_N0.0071.5006.400R
CPUCORE_ISNS1_P0.0071.5006.400R
CPUCORE_ISNS2_N0.0071.5006.400R
CPUCORE_ISNS2_P0.0071.5006.400R
CPUCORE_ISUMN0.008–8.100R
CPUCORE_ISUMN_R0.486––
CPUCORE_ISUMP0.487––
CPUCORE_PSYS0.632––
CPUCORE_PWM10.622––
CPUCORE_PWM20.623––
CPUCORE_SW10.0071.5006.400R
CPUCORE_SW20.0071.5006.400R
CPUCORE1_DRVHOL––
CPUCORE2_DRVHOL––
CPUCORE2_GL00.436––
CPUDDR_IOUTOL––
CPUGT_BOOT10.616––
CPUGT_BP10.610––
CPUGT_BP20.608––
CPUGT_FCCM0.613––
CPUGT_ISEN10.638––
CPUGT_ISEN20.637––
CPUGT_ISNS1_N0.0071.5006.700R
CPUGT_ISNS1_P0.0071.5006.700R
CPUGT_ISNS2_N0.0071.5006.700R
CPUGT_ISNS2_P0.0071.5006.700R
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN0.009–8.200R
CPUGT_ISUMN_R0.485––
CPUGT_ISUMP0.488––
CPUGT_PHASE10.008–7.900R
CPUGT_PWM10.623––
CPUGT_PWM20.622––
CPUGT_SW10.007–6.700R
CPUGT_SW1_SNUBOL––
CPUGT_SW20.007––
CPUGT1_DRVHOL––
CPUGT1_GL00.440––
CPUGT2_DRVHOL––
CPUGTVSENSE_IN0.009–8.600R
CPUREGMISCP5V_IOUTOL––
CPUSA_DRVH0.605––
CPUSA_FCCM0.623––
CPUSA_GL00.432––
CPUSA_ISNS_N0.045–45.000R
CPUSA_ISNS_P0.045–44.300R
CPUSA_ISNS_R_N0.0371.15036.000R
CPUSA_ISNS_R_P0.0371.15036.000R
CPUSA_ISUMN0.037–36.000R
CPUSA_ISUMN_R0.501––
CPUSA_ISUMP0.584––
CPUSA_PWM0.623––
CPUSAVSENSE_IN0.030–29.900R
CPUVCCIO_IOUTOL––
CPUVR_ISUM_IOUTOL––
CPUVR_SWSA0.031––
CPUVR_VIDALERT_L_R0.320––
CPUVR_VIDSCLK_R0.320––
CPUVR_VIDSOUT_R0.269––
CSI2_COMP0.101––
DDRREG_VTTSNS0.155––
DEBUG_JTAG_SOC_TDI0.4598––
DEBUG_JTAG_SOC_TDO0.4582––
DFR_DISP_INT0.485––
DFR_DISP_RESET_L0.485––
DFR_DISP_TE0.486––
DFR_DISP_VSYNCOL––
DFR_PWR_EN0.481––
DFR_PWR_EN_R0.565––
DFR_TOUCH_CLK32K_RESET_L0.487––
DFR_TOUCH_INT_L0.482––
DFR_TOUCH_LID_OPEN_LOL––
DFR_TOUCH_RESET_L0.485––
DFR3V3_IOUTOL––
DFUMUX_SELOL––
DP_INT_HPDOL––
DP_INT_HPD_L0.484––
DP_INT_HPD_MASK0.470––
DP_XA_HPD0.591––
DP_XB_HPD0.588––
EADC1_CH2OL––
EADC1_P3V3_DFR_ISENSEOL––
EADC1_P3V3_KBD_ISENSEOL––
EADC2_CH2OL––
EADC2_CH5OL––
EADC2_KBBLT_ISENSEOL––
EADC2_MESA_ISENSEOL––
EADC2_P1V8_LPDDROL––
EADC2_P3V3_TPAD_ISENSEOL––
EADC2_P5V_LCD_ISENSEOL––
EADC2_SPKRAMPR_ISENSEOL––
EDP_AUXCH_N0.261––
EDP_AUXCH_P0.262––
EDP_BKLT_EN0.552––
EDP_BKLT_PWM0.8150––
EDP_COMP0.159––
EDP_ML_N<0>0.2612––
EDP_ML_N<1>0.263––
EDP_ML_N<2>0.264––
EDP_ML_N<3>0.263––
EDP_ML_P<0>0.264––
EDP_ML_P<1>0.262––
EDP_ML_P<2>0.262––
EDP_ML_P<3>0.263––
EDP_PANEL_PWR_BUF_EN0.717––
EDP_PANEL_PWR_DLY_EN0.704––
EDP_PANEL_PWR_EN0.570––
EMMC_RCOMP0.201––
ENET_CLKREQ_L0.486––
ESPI_CS_L0.477––
ESPI_IO<0>0.492––
ESPI_IO<1>0.492––
ESPI_IO<2>0.492––
ESPI_IO<3>0.492––
ESPI_RESET_L0.477––
FAN_RT_PWM0.7551––
FAN_RT_TACHOL––
FB_A_CPUGT0.615––
FB_A_GT_R1.622––
FB_A_GT_RC1.337––
FB_B_CORE_R1.626––
FB_B_CORE_RC1.338––
FB_B_CPUCORE0.619––
FB_C_CPUSA0.616––
FB_C_SA_R1.619––
FB_C_SA_RC1.424––
FB_CORE_R0.009––
FB_GT_R0.009––
FB_SA_R0.038––
GND0.0005––
GND_FAN0.000––
GND_SMC_AVSS0.000––
I2C_ALS_SCL0.480––
I2C_ALS_SCL_R0.476––
I2C_ALS_SDA0.477––
I2C_ALS_SDA_R0.478––
I2C_BKLT_SCL0.545––
I2C_BKLT_SDA0.545––
I2C_CODEC_SCL0.483––
I2C_CODEC_SDA0.483––
I2C_DFR_SCL0.481––
I2C_DFR_SCL_R0.497––
I2C_DFR_SDA0.480––
I2C_DFR_SDA_R0.497––
I2C_DISP_3V3_SCL0.4829––
I2C_DISP_3V3_SDA0.4834––
I2C_DISP_LS_EN0.487––
I2C_DISP_SCL0.458––
I2C_DISP_SDA0.457––
I2C_FTCAM_DSBL_SCL0.636––
I2C_FTCAM_DSBL_SDA0.636––
I2C_FTCAM_ISOL_SCL0.746––
I2C_FTCAM_ISOL_SDA0.7409––
I2C_FTCAM_SCL_R0.477––
I2C_FTCAM_SDA_R0.478––
I2C_KBD_SCLOL––
I2C_KBD_SDAOL––
I2C_PWR_SCL0.484––
I2C_PWR_SCL_R10.483––
I2C_PWR_SCL_R20.482––
I2C_PWR_SDA0.483––
I2C_PWR_SDA_R10.481––
I2C_PWR_SDA_R20.481––
I2C_SENSE_5V_SCLOL––
I2C_SENSE_5V_SCL_R1OL––
I2C_SENSE_5V_SCL_R2OL––
I2C_SENSE_5V_SDAOL––
I2C_SENSE_5V_SDA_R1OL––
I2C_SENSE_5V_SDA_R2OL––
I2C_SENSE_SCL0.482––
I2C_SENSE_SCL_R10.479––
I2C_SENSE_SCL_R2OL––
I2C_SENSE_SDA0.483––
I2C_SENSE_SDA_R10.479––
I2C_SENSE_SDA_R2OL––
I2C_SEP_SCL0.478––
I2C_SEP_SDA0.477––
I2C_SNS0_S0_SCL0.475––
I2C_SNS0_S0_SDA0.475––
I2C_SPKRAMP_L_SCL0.388––
I2C_SPKRAMP_L_SDA0.388––
I2C_SPKRAMP_R_SCL0.388––
I2C_SPKRAMP_R_SDA0.387––
I2C_SSD_SCL0.484––
I2C_SSD_SDA0.484––
I2C_TBT_X_SCL0.5278––
I2C_TBT_X_SDA0.5286––
I2C_TBT_XA_INT_L0.5990––
I2C_TBT_XB_INT_L0.5747––
I2C_THMSNS_SCL0.477––
I2C_THMSNS_SCL_R00.476––
I2C_THMSNS_SCL_R10.476––
I2C_THMSNS_SCL_R20.480––
I2C_THMSNS_SDA0.477––
I2C_THMSNS_SDA_R00.475––
I2C_THMSNS_SDA_R10.475––
I2C_THMSNS_SDA_R20.480––
I2C_TPAD_3V3_SCL0.9443––
I2C_TPAD_3V3_SCL_R0.986––
I2C_TPAD_3V3_SDA0.9372––
I2C_TPAD_3V3_SDA_R0.979––
I2C_UPC_SCL0.474––
I2C_UPC_SDA0.476––
I2C_UPC_X_SCL20.476––
I2C_UPC_X_SDA20.479––
I2C_UPC_XA_DBG_CTL_SCL0.599––
I2C_UPC_XA_DBG_CTL_SDA0.598––
I2C_UPC_XB_DBG_CTL_SCL0.590––
I2C_UPC_XB_DBG_CTL_SDA0.591––
I2S_CODEC_BCLK0.481––
I2S_CODEC_D2R0.479––
I2S_CODEC_LRCLK_R0.490––
I2S_CODEC_R2D0.455––
I2S_SPKRAMP_L_BCLK0.389––
I2S_SPKRAMP_L_D2R0.380––
I2S_SPKRAMP_L_D2R_R10.385––
I2S_SPKRAMP_L_D2R_R20.387––
I2S_SPKRAMP_L_LRCLK_R0.387––
I2S_SPKRAMP_L_R2D0.388––
I2S_SPKRAMP_R_BCLK0.389––
I2S_SPKRAMP_R_D2R_R20.389––
I2S_SPKRAMP_R_LRCLK_R0.387––
I2S_SPKRAMP_R_R2D0.388––
IMON_A_CPUGT0.635––
IMON_B_CPUCORE0.637––
IMON_C_CPUSA0.637––
IPD_LID_OPEN0.7034––
ISNS_CALPE_NOL––
ISNS_CALPE_POL––
ISNS_CPUDDR_N0.219––
ISNS_CPUDDR_P0.219––
ISNS_CPUEDRAM_IOUTOL––
ISNS_CPUEDRAM_N0.150––
ISNS_CPUEDRAM_P0.150––
ISNS_CPUGT_NOL––
ISNS_CPUGT_POL––
ISNS_CPUGT_R_NOL––
ISNS_CPUGT_R_POL––
ISNS_CPUSA_IOUTOL––
ISNS_CPUVCCIO_N0.151––
ISNS_CPUVCCIO_P0.151––
ISNS_CPUVDDQ_NOL––
ISNS_CPUVDDQ_POL––
ISNS_CPUVR_NOL––
ISNS_CPUVR_POL––
ISNS_CPUVR_R_NOL––
ISNS_CPUVR_R_POL––
ISNS_DDR_IOUTOL––
ISNS_DFR3V3_NOL––
ISNS_DFR3V3_POL––
ISNS_HS_3V3RTC_NOL––
ISNS_HS_3V3RTC_POL––
ISNS_HS_CPU_N0.474––
ISNS_HS_CPU_P0.474––
ISNS_HS_OTHER3V3_NOL––
ISNS_HS_OTHER3V3_POL––
ISNS_HS_OTHER5V_N0.47412.600–
ISNS_HS_OTHER5V_P0.47412.600–
ISNS_KBBLT_IOUTOL––
ISNS_KBBLT_NOL––
ISNS_KBBLT_POL––
ISNS_KBDP3V3_NOL––
ISNS_KBDP3V3_POL––
ISNS_LCDBKLT_N0.47412.600–
ISNS_LCDBKLT_P0.47412.600–
ISNS_LCDPANEL_N0.478––
ISNS_LCDPANEL_P0.478––
ISNS_MESA_IOUTOL––
ISNS_MESA_NOL––
ISNS_MESA_POL––
ISNS_OCARINA_N0.415––
ISNS_OCARINA_P0.415––
ISNS_P1V8G3S_NOL––
ISNS_P1V8G3S_POL––
ISNS_P1V8LPDDR_NOL––
ISNS_P1V8LPDDR_POL––
ISNS_P5VCPUREGMISC_NOL––
ISNS_P5VCPUREGMISC_POL––
ISNS_PP5V_LCD_N0.576––
ISNS_PP5V_LCD_P0.576––
ISNS_SPKRAMP_LEFT_NOL––
ISNS_SPKRAMP_LEFT_POL––
ISNS_SPKRAMP_RIGHT_NOL––
ISNS_SPKRAMP_RIGHT_POL––
ISNS_SSDNAND_N0.474––
ISNS_SSDNAND_P0.474––
ISNS_TBTX_NOL––
ISNS_TBTX_POL––
ISNS_TPADP3V3_NOL––
ISNS_TPADP3V3_POL––
ISNS_TPADP5V_NOL––
ISNS_TPADP5V_POL––
ISNS_WLAN_OPOL––
ISNS_WLANBTP1V8_NOL––
ISNS_WLANBTP1V8_POL––
ISNS_WLANBTP3V3_NOL––
ISNS_WLANBTP3V3_POL––
ISNS_WLANBTP3V3_R_NOL––
ISNS_WLANBTP3V3_R_POL––
ITP_PMODE0.3710––
JTAG_ISP_TCK0.588––
JTAG_ISP_TDI0.591––
JTAG_ISP_TDO0.590––
JTAG_TBT_T_TMS0.807––
JTAG_TBT_X_TMS0.580––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_INT_LOL––
KBDP3V3_IOUTOL––
L83_FILT0.721––
L83_FLYC0.404––
L83_FLYN0.520––
L83_HSBIAS_FILT0.712––
L83_HSBIAS_FILT_REF0.647––
L83_VCP_FILT_GND0.000––
L83_VCP_FILTN0.688––
L83_VCP_FILTP0.395––
LCD_PWR_SLEW0.626––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.742––
LCDBKLT_FET_DRVOL––
LCDBKLT_FET_DRV_R0.520––
LCDBKLT_IOUTOL––
LCDBKLT_SW0.445––
LCDP5V_IOUTOL––
LCDPANEL_IOUTOL––
LID_OPEN_LEFT0.650––
LID_OPEN_RIGHT0.730––
LPDDRP1V8_IOUTOL––
MEM_VREFCA_RC0.026––
MEMVTT_EN0.532––
MEMVTT_EN_R0.530––
MESA_BOOST_EN0.489––
MESA_BOOST_EN_CONN0.5378––
MESA_INT_CONN0.4593––
MESA_PWR_EN0.481––
MIPI_DFR_CLK_FILT_CONN_N0.542––
MIPI_DFR_CLK_FILT_CONN_P0.544––
MIPI_DFR_CLK_N0.542––
MIPI_DFR_CLK_P0.544––
MIPI_DFR_DATA_FILT_CONN_N0.544––
MIPI_DFR_DATA_FILT_CONN_P0.542––
MIPI_DFR_DATA_N0.544––
MIPI_DFR_DATA_P0.542––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_N0.757––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_P0.772––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_N<0>0.775––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_P<0>0.775––
MIPI_FTCAM_DATA_N<0>0.533––
MIPI_FTCAM_DATA_P<0>0.534––
MLB_RAMCFG00.719––
MLB_RAMCFG10.772––
NTC_A_CPUGT0.637––
NTC_A_CPUGT_RN0.001–0.040R
NTC_A_CPUGT_RPOL––
NTC_B_CPUCORE0.645––
NTC_B_CPUCORE_RN0.000–0.400R
NTC_B_CPUCORE_RPOL––
OCARINA_FORCE_ENOL––
OCARINA_NAND_VCC_DETOL––
OCARINA_PGOODOL––
OCARINA_POK20.001––
OCARINA_TCALOL––
OCARINA_TDEV1OL––
OCARINA_TDEV2OL––
OCARINA_VDD_LDOOL––
OCARINA_VREFOL––
OPCE_RCOMP0.052––
P0V9_TBT_X_SVR_AGND0.001––
P0V9SLPDDR_FB_R0.087–85.600R
P0V9SLPDDR_SW00.08–51.00R
P0V9SLPDDR_SW10.08–51.00R
P0V9SSD_FB_R_N0.001–1.100R
P0V9SSD_FB_R_P0.452––
P1V1_SLPDDR_SOCFET_EN0.571––
P1V1_SLPDDR_SOCFET_EN_ROL––
P1V1SLPS2R_SW00.27–2.80k
P1V1SLPS2R_SW10.27–2.80k
P1V2_BOOT_RC0.643––
P1V2_DRVH0.712––
P1V2_DRVH_R0.713––
P1V2_DRVL0.462––
P1V2_DRVL_R0.463––
P1V2_LL_SNUBOL––
P1V2_PHASE0.2201.200217.000R
P1V2_SNS0.231––
P1V2_SNS_R0.240––
P1V2_SW0.222––
P1V2_VBST0.641––
P1V2REG_AGND0.000––
P1V2REG_VREF0.653––
P1V2REG_VREF_ROL––
P1V2S0SW_FET_EN0.573––
P1V2S0SW_RAMP0.718––
P1V8_DFR_R0.730––
P1V8G3S_EN0.569–310.000R
P1V8G3S_SS0.726––
P1VPRIM_FB_R0.194––
P2V5_SSD_DISCHARGE0.342––
P3V3G3H_COMP20.754––
P3V3G3H_COMP2_ROL––
P3V3G3H_CS2_L_N0.4203.300–
P3V3G3H_CS2_L_P0.420––
P3V3G3H_CSP21.292––
P3V3G3H_DRVH0.982––
P3V3G3H_DRVH_R0.981––
P3V3G3H_DRVL0.566––
P3V3G3H_DRVL_R0.566––
P3V3G3H_RF0.593––
P3V3G3H_SNUBROL––
P3V3G3H_SW0.419––
P3V3G3H_VBST0.642––
P3V3G3H_VBST_R0.635––
P3V3G3H_VFB20.596––
P3V3G3H_VFB2_R0.415––
P3V3G3H_VFB2_R20.425––
P3V3G3H_VFB2_RROL––
P3V3G3H_VSW0.4203.300–
P3V3G3HRTC_FB1.422––
P3V3G3HRTC_FB_R0.435––
P3V3G3HRTC_PGOOD0.697––
P3V3G3HRTC_PHASE10.4253.300–
P3V3G3HRTC_PHASE20.4253.300–
P3V3G3HRTC_RA_R0.435––
P3V3G3HRTC_SS0.541––
P3V3G3S_EN0.567––
P3V3G3S_SS0.610––
P3V3MAIN_PGOOD0.5903.300–
P3V3TBT_X_RAMP0.500––
P5V_S4SW_SNS_FET_RAMPOL––
P5VG3S_COMP10.750––
P5VG3S_COMP1_ROL––
P5VG3S_CS1_L_N0.4205.000–
P5VG3S_CS1_L_P0.4205.000–
P5VG3S_CSP11.264––
P5VG3S_DRVH0.991––
P5VG3S_DRVH_ROL––
P5VG3S_DRVL0.565––
P5VG3S_DRVL_R0.566––
P5VG3S_EN0.5841.800–
P5VG3S_EN_DLY0.5283.300–
P5VG3S_EN_R0.585––
P5VG3S_PGOOD0.584––
P5VG3S_SNUBROL––
P5VG3S_SW0.425––
P5VG3S_VBST0.642––
P5VG3S_VBST_R0.636––
P5VG3S_VFB10.586––
P5VG3S_VFB1_R0.422––
P5VG3S_VFB1_R20.433––
P5VG3S_VFB1_RROL––
P5VG3S_VSW0.4205.000–
P5VP3V3_SKIPSEL0.488––
P5VP3V3_VREF20.491––
P5VP3V3_VREG30.519––
P5VXX_EN0.594––
PANEL_P3V3_EN0.574––
PANEL_P3V3_EN_D0.744––
PANEL_P5V_EN0.577––
PANEL_P5V_EN_DOL––
PBUS_DIVIDER0.789––
PBUS_DIVIDER_OUT0.712––
PBUS_DIVIDER_REF0.729––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.472––
PBUSVSENS_EN_L0.476––
PBUSVSENS_EN_L_DIVOL––
PCH_BT_AUDIO_SYNC0.696––
PCH_BT_UART_CTS_L0.829––
PCH_BT_UART_D2R0.818––
PCH_BT_UART_R2D0.825––
PCH_BT_UART_RTS_L0.827––
PCH_CLK24M_XTALIN0.844––
PCH_CLK24M_XTALOUT0.840––
PCH_CLK24M_XTALOUT_R0.840––
PCH_DDPC_CTRLDATA0.801––
PCH_DIFFCLK_BIASREF0.061–60.700R
PCH_GPP_A70.826––
PCH_HSIO_PWR_EN0.821––
PCH_JTAGX0.052–51.400R
PCH_LAN_WAKE_L0.824––
PCH_PCIE_CLK100M_WLAN_N0.336––
PCH_PCIE_CLK100M_WLAN_P0.336––
PCH_PCIE_RCOMP_N0.350––
PCH_PWRBTN_L0.771––
PCH_RTC_RESET_L0.777––
PCH_STRP_ESPI0.811––
PCH_STRP_JTAGODTDIS0.808––
PCH_STRP_NO_REBOOT0.809––
PCH_STRP_XTAL_24MHZ0.809––
PCH_SWD_SOC_CLK0.586––
PCH_SWD_SOC_IO0.569––
PCH_UART_DEBUG_D2R0.6864––
PCH_UART_DEBUG_R_D2R0.704––
PCH_UART_DEBUG_R_R2D0.705––
PCH_UART_DEBUG_R2D0.6754––
PCH_WLAN_AUDIO_SYNC0.705––
PCH_WLAN_CLKREQ_L0.827––
PCH_WLAN_DEV_WAKE0.832––
PCH_WLAN_PERST_L0.546––
PCIE_CLK100M_SSD0_01_N0.1200.124 Without%2bNand%2b0.124 Without+Nand+––
PCIE_CLK100M_SSD0_01_P0.1210.124 Without%2bNand%2b0.124 Without+Nand+––
PCIE_CLK100M_SSD0_23_N0.121––
PCIE_CLK100M_SSD0_23_P0.121––
PCIE_CLK100M_TBT_X_N0.335––
PCIE_CLK100M_TBT_X_P0.338––
PCIE_PME_L0.559––
PCIE_SSD0_D2R_C_N<0>OL Without%2bNand%2b––
PCIE_SSD0_D2R_C_N<1>OL Without+Nand+––
PCIE_SSD0_D2R_C_P<0>OL Without%2bNand%2b––
PCIE_SSD0_D2R_C_P<1>OL Without+Nand+––
PCIE_SSD0_D2R_N<0>0.410––
PCIE_SSD0_D2R_P<0>0.408––
PCIE_SSD0_R2D_N<0>OL Without%2bNand%2b––
PCIE_SSD0_R2D_N<1>OL Without+Nand+––
PCIE_SSD0_R2D_P<0>OL Without%2bNand%2b––
PCIE_SSD0_R2D_P<1>OL Without+Nand+––
PD_UPC_X_5V_EN0.646––
PD_UPC_XA_GPIO40.693––
PD_UPC_XB_GPIO10.695––
PD_UPC_XB_GPIO40.696––
PD_UPC_XB_GPIO90.719––
PD_UPC_XB_GPIO100.721––
PDM_DMIC_CLK00.503––
PDM_DMIC_CLK10.504––
PDM_DMIC_DATA0_UNSEC0.566––
PDM_DMIC_DATA10.471––
PDM_DMIC_DATA1_RR0.490––
PDM_DMIC_DATA1_UNSEC0.566––
PLT_RST_3V3_L0.596––
PLT_RST_L0.577––
PM_MEMVTT_EN0.403––
PM_OPC_ZVM_L0.591––
PM_PCH_PWROK0.512––
PM_PCH_SYS_PWROK0.574––
PM_RSMRST_L0.544––
PM_SLP_S0_3V3_L0.515––
PM_SLP_S0_L0.479––
PM_SLP_S0_R_LOL––
PM_SLP_S3_L0.590––
PM_SLP_S4_L0.819––
PM_SLP_S5_L0.820––
PM_SLP_SUS_L0.820––
PM_SLP_TIEOFF0.718––
PM_SYSRST_L0.820––
PM_SYSRST_R_L0.570––
PM_THRMTRIP_L0.278––
PMIC_DISCHARGE_EN_RCOL––
PMU_ACTIVE_READY0.482––
PMU_ACTIVE_READY_ROL––
PMU_CLK32K_PCH0.814––
PMU_CLK32K_PCH_R0.782––
PMU_CLK32K_SOC0.486––
PMU_CLK32K_SOC_R0.519––
PMU_CLK32K_WLANBT0.452––
PMU_CLK32K_WLANBT_R0.486––
PMU_COLD_RESET_L0.480––
PMU_CPUDDR_ISENSE0.590––
PMU_CPUEDRAM_ISENSE0.591––
PMU_CPUGT_ISENSE0.589––
PMU_CPUGT_VSENSE0.584––
PMU_CPUSA_ISENSE0.059––
PMU_CPUVCCIO_ISENSE0.591––
PMU_DDR1V2_ISENSE0.590––
PMU_FORCE_DFU0.771––
PMU_INT_L0.486––
PMU_LDO3_OUT_R0.608––
PMU_ONOFF_L0.718––
PMU_ONOFF_R_L_CONN0.723––
PMU_P5V_CPUREGMISC_ISENSE0.589––
PMU_PVDDMAIN_EN0.7723.300–
PMU_RSLOC_RST_L0.721––
PMU_SYS_ALIVE0.420––
PP_SSD0_S4E0_VPP0.632OL Without%2bNand%2b––
PP_SSD0_S4E1_VPP0.634OL Without+Nand+––
PP_SSD0_S4E2_VPPOL––
PP_SSD0_S4E3_VPPOL––
PP0V6_S0_DDRVTT0.153––
PP0V6_S3_MEM_VREFCA_A0.378––
PP0V6_S3_MEM_VREFDQ_A0.378––
PP0V6_S3_MEM_VREFDQ_B0.380––
PP0V8_SLPS2R0.225––
PP0V9_SE_VMID0.600––
PP0V9_SLPDDR0.091–125.000R
PP0V9_SSD00.4510.530 Without%2bNand%2b0.530 Without+Nand+––
PP0V9_SSD0_S4E0_VDD_PLL0.4500.530 Without%2bNand%2b––
PP0V9_SSD0_S4E1_VDD_PLL0.4500.520 Without+Nand+––
PP0V9_SSD0_S4E2_VDD_PLLOL––
PP0V9_SSD0_S4E3_VDD_PLLOL––
PP0V9_TBT_X_LC0.343––
PP0V9_TBT_X_LVR0.478––
PP0V9_TBT_X_PCIE0.297––
PP0V9_TBT_X_SVR0.2770.900–
PP0V82_SLPDDR0.053–52.900R
PP0V95_S0_CPUVCCIO_REG_R0.1360.950134.800
PP1V_PRIM0.1521––
PP1V_S0SW0.237––
PP1V_S30.248––
PP1V1_SLPDDR0.426––
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.425––
PP1V1_SLPS2R0.410––
PP1V2_AWAKE0.540––
PP1V2_AWAKE_SOC_PCIEPLL_F0.537––
PP1V2_S0SW0.291––
PP1V2_S30.2191.200–
PP1V2_S3_CPUDDR0.221––
PP1V2_S3_REG_R0.2201.200–
PP1V05_PRIM_PCH_VCCA19P2_XW0.188––
PP1V05_PRIM_PCH_VCCABCLK_XW0.188––
PP1V05_PRIM_PCH_VCCAPLL_AUD_F0.189––
PP1V05_PRIM_PCH_VCCASRC_XW0.188––
PP1V05_PRIM_PCH_VCCAXTAL_F0.190––
PP1V05_PRIMSW_PCH_VCCAMPHYPLL_F0.188––
PP1V05_S5_PCH_VCCDSW0.482––
PP1V5_UPC_XA_LDO_CORE0.521––
PP1V5_UPC_XB_LDO_CORE0.521––
PP1V8_ACCEL_FILTOL––
PP1V8_AWAKE0.433––
PP1V8_AWAKE_SOC_TSADC_RC0.430––
PP1V8_CODEC0.339––
PP1V8_CODEC_VCP0.339––
PP1V8_CODEC_VCP_SEL0.339––
PP1V8_CODEC_VL0.335––
PP1V8_CODEC_VL_SEL0.339––
PP1V8_DFR0.552––
PP1V8_DISOL––
PP1V8_DMIC0.338––
PP1V8_G3S0.338––
PP1V8_G3S_REG0.338––
PP1V8_G3S_WLANBT0.341––
PP1V8_IO_SSD00.3470.520 Without%2bNand%2b0.510 Without+Nand+––
PP1V8_IO_SSD0_R0.768––
PP1V8_IO_SSD0_R2OL––
PP1V8_MESA0.534––
PP1V8_MESA_FILT_CONN0.5121––
PP1V8_PRIM_PCH_VCCHDA_F0.344––
PP1V8_S0_THMSNSA_R0.343––
PP1V8_S0_THMSNSB_R0.344––
PP1V8_S30.479––
PP1V8_S3_MEM0.479––
PP1V8_S50.3031––
PP1V8_SE_AVDD0.322––
PP1V8_SE_ESE0.365––
PP1V8_SLPS2R0.422––
PP1V8_SLPS2R_PMUVDDGPIO0.749––
PP1V8_SLPS2R_SOC_LPADC_RC0.458––
PP1V8_SSD0_S4E0_AVDD18_PLL0.3480.520 Without%2bNand%2b––
PP1V8_SSD0_S4E0_PCI_AVDD_H0.3480.520 Without%2bNand%2b––
PP1V8_SSD0_S4E1_AVDD18_PLL0.3480.520 Without+Nand+––
PP1V8_SSD0_S4E1_PCI_AVDD_H0.3480.510 Without+Nand+––
PP1V8_SSD0_S4E2_AVDD18_PLLOL––
PP1V8_SSD0_S4E2_PCI_AVDD_HOL––
PP1V8_SSD0_S4E3_AVDD18_PLLOL––
PP1V8_SSD0_S4E3_PCI_AVDD_HOL––
PP1V24_S5_PCH_VCCDPHY0.435––
PP1V25_SLPS2R_SMC_AVREF0.619––
PP2V5_ADC1_VREFOL––
PP2V5_ADC2_VREFOL––
PP2V5_NAND_SSD00.3460.370 Without%2bNand%2b0.370 Without+Nand+2.500–
PP2V5_SSD0_AGND0.001––
PP3V_G3H_RTC0.511––
PP3V0_MESA0.563––
PP3V0_MESA_FILT_CONN0.5479––
PP3V3_AWAKE0.658––
PP3V3_CODEC_LDO_IN0.369––
PP3V3_CODEC_VP0.370––
PP3V3_G3H0.4203.300–
PP3V3_G3H_BMU0.414––
PP3V3_G3H_MESA_SW0.427––
PP3V3_G3H_PMU_VDDMAIN0.422––
PP3V3_G3H_PMU_VINRTC_R0.429––
PP3V3_G3H_RTC0.430––
PP3V3_G3H_RTC_DFR0.416––
PP3V3_G3H_RTC_MESA0.430––
PP3V3_G3H_RTC_REG_R0.4253.300–
PP3V3_G3H_SSD00.417––
PP3V3_G3HSW_DFR0.579––
PP3V3_G3S0.365––
PP3V3_G3S_KBD0.368––
PP3V3_G3S_TPAD0.3336––
PP3V3_G3S_WLANBT0.365––
PP3V3_S0_TBT_X_ISNS_R0.530––
PP3V3_S0SW_LCD0.4757––
PP3V3_S0SW_LCD_R0.478––
PP3V3_S4SW_SNS0.560––
PP3V3_S50.3620––
PP3V3_TBT_X_ANA0.531––
PP3V3_TBT_X_ANA_PCIE0.510––
PP3V3_TBT_X_ANA_USB20.490––
PP3V3_TBT_X_LC0.565––
PP3V3_TBT_X_S00.530––
PP3V3_TBT_X_SX0.497––
PP3V3_TBT_X_SX_R0.500––
PP3V3_UPC_XA_LDO0.516––
PP3V3_UPC_XB_LDO0.500––
PP5V_COREVR_VCC0.426––
PP5V_EADC2_AVDDOL––
PP5V_EDRAM_V5IN0.427––
PP5V_G3H_LDO0.489––
PP5V_G3S0.4205.000–
PP5V_G3S_ALSCAM0.426––
PP5V_G3S_CPUREG_MISC0.426––
PP5V_G3S_DFR_FILT0.4195––
PP5V_G3S_EDRAMPVCC0.427––
PP5V_G3S_EDRAMVCC0.427––
PP5V_G3S_FAN_CONN0.4154––
PP5V_G3S_KBD0.426––
PP5V_G3S_TPAD0.423––
PP5V_G3S_TPAD_CONN0.4147––
PP5V_G3S_VCCIOPVCC0.431––
PP5V_G3S_VCCIOVCC0.429––
PP5V_MAIN_VCCSA0.427––
PP5V_MAIN_VCORE10.423––
PP5V_MAIN_VCORE20.427––
PP5V_MAIN_VGT10.425––
PP5V_S0_BKLT_A0.424––
PP5V_S0_BKLT_D0.423––
PP5V_S0SW_LCD0.576––
PP5V_S0SW_LCD_R0.576––
PP5V_S4SWOL––
PP5V_WLAN_ISNS_DOL––
PP16V0_MESA0.653––
PP16V0_MESA_FILT_CONN0.6416––
PP17V0_MOJAVE_LDOIN0.595––
PP20V_USBC_XA_VBUS0.15620.000–
PP20V_USBC_XB_VBUS0.15620.000–
PPBUS_G3H0.47412.600–
PPBUS_G3H_SPKRAMP_LEFT0.47512.600–
PPBUS_G3H_SPKRAMP_RIGHT0.47112.600–
PPBUS_G3H_SSD00.47412.600–
PPBUS_HS_CPU0.47412.600–
PPDCIN_G3H0.56020.000–
PPDCIN_G3H_CHGR0.55920.000–
PPDCIN_XA_G3H_F0.56020.000–
PPDCIN_XB_G3H_F0.56020.000–
PPVBAT_G3H_CHGR_R0.474––
PPVBAT_G3H_CHGR_REG0.47412.600–
PPVBAT_G3H_CONN1.561––
PPVCC_CPU_PH10.0071.5006.400R
PPVCC_CPU_PH20.0071.5006.400R
PPVCC_S0_CPU0.0071.5006.400R
PPVCC_SW1_TPS621800.3462.500–
PPVCC_SW2_TPS621800.3462.500–
PPVCCEDRAM_S0_CPU0.1131.000111.700
PPVCCEDRAM_S0_REG_R0.1131.000111.700
PPVCCGT_CPU_PH10.0071.5006.700R
PPVCCGT_CPU_PH20.0071.5006.700R
PPVCCGT_S0_CPU0.0071.5006.700R
PPVCCIO_S0_CPU0.1360.950134.800
PPVCCQ_ANI_SSD00.3470.510 Without%2bNand%2b0.510 Without+Nand+––
PPVCCSA_CPU_R0.0371.15036.000R
PPVCCSA_S0_CPU0.0371.15036.000R
PPVDDCPU_AWAKE0.029–28.100R
PPVDDCPUSRAM_AWAKE0.411––
PPVIN_G3H_P3V3G3H0.47412.600–
PPVIN_G3H_P3V3G3HRTC0.47412.600–
PPVIN_G3H_P3V3G3HRTC_R0.473––
PPVIN_G3H_P5VG3S0.47412.600–
PPVIN_S0_CPUVR_VIN0.483––
PPVIN_S0SW_LCDBKLT0.85012.600–
PPVIN_S0SW_LCDBKLT_F0.47412.600–
PPVIN_S0SW_LCDBKLT_R0.47412.600–
PPVIN_S4_TPAD_FUSE0.3344––
PPVIN_SW_LCDBKLT_SW0.85012.600–
PPVOUT_S0_LCDBKLT1.214046.000–
PPVOUT_S0_LCDBKLT_F1.20546.000–
PPVPCORE_S50.304––
PPVTT_VTTREF0.502––
PROG1_CPUCOREVR0.632––
PROG2_CPUCOREVR0.630––
PROG3_CPUCOREVR0.633––
PROG4_CPUCOREVR0.634––
PROG5_CPUCOREVR0.635––
PVCC_FB_N0.001–1.400R
PVCC_FB_P0.305––
PVCCCGT_PH1_AGND0.000–0.400R
PVCCCGT_PH2_AGND0.001––
PVCCCSA_AGND0.000––
PVCCEDRAM_BOOT_RC0.594––
PVCCEDRAM_DRVH_R0.576––
PVCCEDRAM_DRVL0.461––
PVCCEDRAM_DRVL_R0.459––
PVCCEDRAM_LL0.120––
PVCCEDRAM_LL_SNUBOL––
PVCCEDRAM_PHASE0.0431.000111.700
PVCCEDRAM_REFIN0.707––
PVCCEDRAM_VBST0.591––
PVCCEDRAMS0_CS_N0.1131.000111.700
PVCCEDRAMS0_CS_P0.1131.000111.700
PVCCEDRAMS0_EN0.785––
PVCCEDRAMS0_EN_FILT0.764––
PVCCEDRAMS0_EN_FILT_BUF0.551––
PVCCEDRAMS0_OCSET0.547––
PVCCEDRAMS0_RTN0.540––
PVCCEDRAMS0_SREF0.550––
PVCCEDRAMS0_VO0.548––
PVCCEOPIO_EDRAM_PGOOD0.549––
PVCCIO_BOOT_RC0.597––
PVCCIO_DRVH0.598––
PVCCIO_DRVH_R0.599––
PVCCIO_DRVL_R0.458––
PVCCIO_EN0.767––
PVCCIO_LL0.142––
PVCCIO_LL_SNUBOL––
PVCCIO_PHASE0.1360.950134.800
PVCCIO_VBST0.595––
PVCCIOS0_AGND0.000––
PVCCIOS0_CS_N0.1360.950134.800
PVCCIOS0_CS_P0.1360.950134.800
PVCCIOS0_EN0.787––
PVCCIOS0_EN_FILT0.758––
PVCCIOS0_EN_FILT_BUF0.546––
PVCCIOS0_EN_R0.806––
PVCCIOS0_FB0.531––
PVCCIOS0_FSEL0.550––
PVCCIOS0_RTN0.539––
PVCCIOS0_SREF0.550––
PVCCIOS0_VO0.545––
PVCCOIOS0_OCSET0.541––
PVCCPLLOC_EN0.768––
PVCCQ_LX0OL––
PVCCQ_SSD_FB_DISOL––
PVCCQSSD_FB_R0.355––
PVDD_LX0OL––
PVDD_LX1OL––
PVDD_SSD_FB_DISOL––
PVDD_SSD_FB_R0.451––
PVDDCPUAWAKE_FB_R0.032–32.200R
PVDDQ_EN0.567––
PVDDQ_EN_LEDOL––
PVDDQ_EN_R0.562––
PVDDQ_PGOOD0.577––
PVTT_VTTSNS0.152––
PWR_SCL_R00.484––
PWR_SDA_R00.482––
RTN_A_CPUGTOL––
S4E2_DROOP_LOL––
S4E3_DROOP_LOL––
SA_ISUMN_R1.044––
SAVE_BAT_G0.782––
SAVE_BAT_S1.565––
SD_RCOMP0.201––
SE_CTLR_FW_DWLD0.484––
SE_DEV_WAKE0.482––
SE_PWR_EN0.747––
SENSOR_PWR_EN0.629––
SEP_CAM_DISABLE_DFF_L0.712––
SEP_CAM_DISABLE_L0.000––
SEP_DISABLE_STROBE0.478––
SEP_DMIC_DISABLE_L0.477––
SEP_DMIC_DISABLE_OUT_L0.520––
SMBUS_3V3_BATT_SCL1.013––
SMBUS_3V3_BATT_SDA1.004––
SMBUS_5_OEOL––
SMC_CPU_HS_ISENSE0.819––
SMC_DEBUGPRT_R_RX0.484––
SMC_DEBUGPRT_R_TX0.484––
SMC_DEBUGPRT_RX0.4575––
SMC_DEBUGPRT_TX0.4578––
SMC_FAN_0_PWM0.488––
SMC_FAN_0_TACH0.488––
SMC_LID_LEFT0.474––
SMC_LID_RIGHT0.473––
SMC_PCH_PWROK0.470––
SMC_PCH_SYS_PWROK0.466––
SMC_PECI_RX0.490––
SMC_PP1V8_WLANBT_ISENSE0.822––
SMC_PROCHOT_L0.476––
SMC_RSMRST_L0.476––
SMC_SYSRST_L0.476––
SMCRST_TIEOFF0.715––
SML_PCH_0_CLK0.802––
SML_PCH_0_DATA0.755––
SML_PCH_1_CLK0.823––
SML_PCH_1_DATA0.822––
SOC_CLKREQ_L0.825––
SOC_COLD_RESET_L0.486––
SOC_DEBUGPRT_RX0.4569––
SOC_DEBUGPRT_TX0.4563––
SOC_DFU_STATUS0.483––
SOC_DOCK_CONNECT0.486––
SOC_FORCE_DFU0.490––
SOC_HOLD_RESET0.482––
SOC_JTAG_SEL0.484––
SOC_PERST_L0.479––
SOC_SOCHOT_L0.4556––
SOC_SWD_MUX_SEL_PCH0.580––
SOC_TESTMODE0.479––
SOC_USB_VBUS0.3913––
SOC_WDOG0.485––
SOC_XTAL24M_IN0.823––
SOC_XTAL24M_OUT0.813––
SOC_XTAL24M_OUT_R0.813––
SPARE_UPC_XA_DBG0_R0.720––
SPARE_UPC_XA_DBG1_R0.714––
SPARE_UPC_XA_DBG2_R0.715––
SPARE_UPC_XA_DBG3_R0.716––
SPARE_UPC_XA_USB3_RN0.732––
SPARE_UPC_XA_USB3_RP0.734––
SPARE_UPC_XB_USB2_RN0.736––
SPARE_UPC_XB_USB2_RP0.734––
SPARE_UPC_XB_USB3_RN0.736––
SPARE_UPC_XB_USB3_RP0.736––
SPI_ACCEL_CS_L0.483––
SPI_AOP_SENSOR_MISO0.483––
SPI_DFR_CLK0.500––
SPI_DFR_CS_L0.480––
SPI_DFR_MISO_R0.500––
SPI_DFR_MOSI0.500––
SPI_IO2_STRAP_L0.597––
SPI_MESA_CLK0.506––
SPI_MESA_CLK_CONN0.4761––
SPI_MESA_MISO0.485––
SPI_MESA_MISO_CONN0.4605––
SPI_MESA_MOSI0.505––
SPI_MESA_MOSI_CONN0.4754––
SPI_PCHROM_IO<2>0.804––
SPI_PCHROM_IO<3>0.812––
SPI_PCHROM_MOSI0.824––
SPI_SOCROM_CLK0.497––
SPI_SOCROM_CLK_ROL––
SPI_SOCROM_CS_L0.482––
SPI_SOCROM_MISO0.437––
SPI_SOCROM_MISO_R0.433––
SPI_SOCROM_MOSI0.430––
SPI_SOCROM_MOSI_ROL––
SPI_SOCROM_WP_L0.632––
SPI_TPAD_3V3_CLK0.551––
SPI_TPAD_3V3_CLK_R0.570––
SPI_TPAD_3V3_CS_L0.6686––
SPI_TPAD_3V3_MISO0.6737––
SPI_TPAD_3V3_MOSI0.6358––
SPI_TPAD_3V3_MOSI_R0.674––
SPI_TPAD_CS_L0.375––
SPI_TPAD_MISO0.491––
SPI_TPAD_MISO_R0.508––
SPIROM_USE_MLB0.823––
SPKR_ID00.484––
SPKR_ID10.4598––
SPKRAMP_FL_AREG0.590––
SPKRAMP_FL_BSTN0.779––
SPKRAMP_FL_BSTP0.781––
SPKRAMP_FL_DREG0.539––
SPKRAMP_FL_OUTN0.480––
SPKRAMP_FL_OUTP0.476––
SPKRAMP_FL_SNSN0.487––
SPKRAMP_FL_SNSP0.480––
SPKRAMP_FR_BSTN0.784––
SPKRAMP_FR_BSTP0.783––
SPKRAMP_FR_MODE0.469––
SPKRAMP_FR_OUTN0.500––
SPKRAMP_FR_OUTP0.480––
SPKRAMP_FR_SNSN0.500––
SPKRAMP_FR_SNSP0.500––
SPKRAMP_RESET_L0.370––
SPKRAMP_RL_AREG0.590––
SPKRAMP_RL_BSTN0.781––
SPKRAMP_RL_BSTP0.779––
SPKRAMP_RL_DREG0.530––
SPKRAMP_RL_MODE0.001––
SPKRAMP_RL_OUTN0.496––
SPKRAMP_RL_OUTP0.500––
SPKRAMP_RL_SNSN0.500––
SPKRAMP_RR_AREG0.594––
SPKRAMP_RR_BSTP0.783––
SPKRAMP_RR_DREG0.542––
SPKRAMP_RR_MODE0.466––
SPKRAMP_RR_OUTN0.500––
SPKRAMP_RR_OUTP0.500––
SPKRAMP_RR_SNSN0.490––
SPKRAMP_RR_SNSP0.490––
SPKRAMP_RW_AREG0.595––
SPKRAMP_RW_DREG0.540––
SPKRAMPL_IOUTOL––
SPKRAMPR_IOUTOL––
SPKRCONN_FL_OUTN0.480––
SPKRCONN_FL_OUTP0.476––
SPKRCONN_FR_OUTN0.500––
SPKRCONN_FR_OUTP0.480––
SPKRCONN_RL_OUTN0.500––
SPKRCONN_RL_OUTP0.500––
SPKRCONN_RR_OUTN0.500––
SPKRCONN_RR_OUTP0.500––
SSD_BFH0.4460.470 Without%2bNand%2b0.470 Without+Nand+––
SSD_PMU_RESET_L0.486––
SSD0_CLK24M0.458––
SSD0_CLK24M_010.4510.510 Without%2bNand%2b0.510 Without+Nand+––
SSD0_CLK24M_23OL––
SSD0_CLKREQ0_L0.4620.470 Without%2bNand%2b––
SSD0_CLKREQ1_L0.4590.520 Without+Nand+––
SSD0_CLKREQ2_L0.486––
SSD0_CLKREQ3_L0.487––
SSD0_LPB_L0.463OL Without%2bNand%2bOL Without+Nand+––
SSD0_OCARINA_LPB_LOL––
SSD0_OCARINA_PFN_L0.4210.410 Without%2bNand%2b0.410 Without+Nand+––
SSD0_OCARINA_RESET_LOL––
SSD0_OCARINA_WP_LOL––
SSD0_PCIE_RESET_L0.4460.460 Without%2bNand%2b0.460 Without+Nand+––
SSD0_PMIC_DISCHARGE_EN0.773––
SSD0_PMIC_RESET_L0.466––
SSD0_PMIC_VR_P2V5_EN0.654––
SSD0_RESET_L0.4650.760 Without%2bNand%2b0.760 Without+Nand+––
SSD0_S4E_BOOT20.463OL Without%2bNand%2bOL Without+Nand+––
SSD0_S4E_JTAG_SEL0.463OL Without%2bNand%2bOL Without+Nand+––
SSD0_S4E_JTAG_TRST_L0.466OL Without%2bNand%2bOL Without+Nand+––
SSD0_S4E_UART_RX0.462OL Without%2bNand%2bOL Without+Nand+––
SSD0_S4E_UART_TX0.492––
SSD0_S4E0_ANI0_VREF0.726OL Without%2bNand%2b––
SSD0_S4E0_ANI1_VREF0.730OL Without%2bNand%2b––
SSD0_S4E0_DROOP_L0.500OL Without%2bNand%2b––
SSD0_S4E0_JTAG_TDI0.498OL Without%2bNand%2b––
SSD0_S4E0_JTAG_TDO0.467OL Without%2bNand%2bOL Without+Nand+––
SSD0_S4E0_PCIE_RESREF0.789OL Without%2bNand%2b––
SSD0_S4E0_SWD_UID00.492OL Without%2bNand%2b––
SSD0_S4E0_SWD_UID10.492OL Without%2bNand%2b––
SSD0_S4E0_UART_TX0.491OL Without%2bNand%2b––
SSD0_S4E0_ZQ_C0.1010.100 Without%2bNand%2b––
SSD0_S4E0_ZQ_L0.3030.300 Without%2bNand%2b––
SSD0_S4E1_ANI0_VREF0.727OL Without+Nand+––
SSD0_S4E1_ANI1_VREF0.724OL Without+Nand+––
SSD0_S4E1_DROOP_L0.490OL Without+Nand+––
SSD0_S4E1_JTAG_TDO0.490OL Without+Nand+––
SSD0_S4E1_PCIE_RESREF0.796OL Without+Nand+––
SSD0_S4E1_SWD_UID00.486OL Without+Nand+––
SSD0_S4E1_SWD_UID10.486OL Without+Nand+––
SSD0_S4E1_UART_TX0.487OL Without+Nand+––
SSD0_S4E1_ZQ_C0.1010.100 Without+Nand+––
SSD0_S4E1_ZQ_L0.3020.310 Without+Nand+––
SSD0_S4E2_ANI0_VREFOL––
SSD0_S4E2_ANI1_VREFOL––
SSD0_S4E2_JATG_TDOOL––
SSD0_S4E2_PCIE_RESREFOL––
SSD0_S4E2_SWD_UID0OL––
SSD0_S4E2_SWD_UID1OL––
SSD0_S4E2_UART_TXOL––
SSD0_S4E2_ZQ_COL––
SSD0_S4E2_ZQ_LOL––
SSD0_S4E3_ANI0_VREFOL––
SSD0_S4E3_ANI1_VREFOL––
SSD0_S4E3_JTAG_TDO0.489––
SSD0_S4E3_PCIE_RESREFOL––
SSD0_S4E3_SWD_UID0OL––
SSD0_S4E3_SWD_UID1OL––
SSD0_S4E3_UART_TXOL––
SSD0_S4E3_ZQ_COL––
SSD0_S4E3_ZQ_LOL––
SSD0_STG01_ADDROL––
SSD0_SWCLK0.4480.460 Without%2bNand%2b0.460 Without+Nand+––
SSD0_SWCLK_ROL––
SSD0_SWDIO0.4530.460 Without%2bNand%2b0.460 Without+Nand+––
SSD0_VR_P2V5_EN0.651––
SSD0_VR_P2V5_PGOOD0.692––
SSD0_WP_L0.4030.610 Without%2bNand%2b0.610 Without+Nand+––
SSDNAND_IOUTOL––
SWD_SOC_DEBUG_SWCLK0.520––
SWD_SOC_DEBUG_SWDIO0.513––
SWD_SOC_SWCLK0.4586––
SWD_SOC_SWCLK_XB0.514––
SWD_SOC_SWDIO0.4582––
SWD_SOC_SWDIO_XB0.516––
SYS_DETECTOL––
SYS_DETECT_L0.503––
TBT_POC_RESET0.642––
TBT_PWR_EN0.568––
TBT_T_PLUG_EVENT_L0.809––
TBT_WAKE_3V3_L0.573––
TBT_WAKE_L0.480––
TBT_X_BATLOW_L0.594––
TBT_X_CIO_PWR_EN0.549––
TBT_X_CLKREQ_L0.810––
TBT_X_CLKREQ_R_L0.594––
TBT_X_HDMI_DDC_DATA0.590––
TBT_X_PCI_RESET_L0.579––
TBT_X_PCIE_BIAS0.790––
TBT_X_PLUG_EVENT_L0.587––
TBT_X_PWR_EN_1V80.564––
TBT_X_RBIAS0.784––
TBT_X_ROM_WP_L0.583––
TBT_X_RSENSE0.001––
TBT_X_RTD3_PWR_EN0.594––
TBT_X_SPI_ARK_CLKOL––
TBT_X_SPI_CS_L0.589––
TBT_X_SPI_DBG_CLKOL––
TBT_X_SPI_DBG_CS_LOL––
TBT_X_SPI_DBG_MISOOL––
TBT_X_SPI_DBG_MOSIOL––
TBT_X_SPI_MOSI0.595––
TBT_X_TEST_EN0.102––
TBT_X_TEST_PWR_GOOD0.103––
TBT_X_USB_PWR_EN0.560––
TBT_XA_USB2_MXCTL0.593––
TBT_XA_USB2_RBIAS0.203––
TBT_XB_USB2_RBIAS0.201––
TBTTHMSNS_D1_N0.001––
TBTTHMSNS_D1_P0.656––
TBTXP3V3_IOUTOL––
TEST_CPU_A350.306––
TEST_CPU_BJ340.321––
TEST_CPU_BJ360.323––
TEST_CPU_CN360.355––
TEST_CPU_D340.311––
TEST_CPU_F340.367––
TEST_CPU_F370.370––
TEST_NOA_N_100.827––
TEST_NOA_N_110.826––
THMSNSA_ADDR_SEL0.658––
THMSNSA_D2_N0.001––
THMSNSA_D2_P0.660––
THMSNSA_D3_N0.001––
THMSNSA_D3_P0.656––
THMSNSA_D4_N0.001––
THMSNSA_D4_P0.656––
THMSNSA_DN0.001––
THMSNSB_ADDR_SEL0.658––
THMSNSB_D1_N0.002–3.200R
THMSNSB_D1_P0.659––
THMSNSB_D2_N0.001–0.800R
THMSNSB_D2_P0.658––
THMSNSB_D3_N0.001––
THMSNSB_D3_P0.656––
THMSNSB_D4_N0.000––
THMSNSB_D4_P0.658––
THMSNSB_DN0.001––
TP_CPU_PWRGD0.350––
TP_DFR_TOUCH_GPIO2OL––
TP_DFR_TOUCH_PANEL_DETECTOL––
TP_DFR_TOUCH_ROM_WCOL––
TP_JTAG_SOC_TRST_L0.487––
TP_LCD_IRQ_LOL––
TP_P3V3G3H_EN20.595––
TP_SMC_FIXTURE_MODE_L0.487––
TP_SPI_PCHROM_CLK0.824––
TP_SPI_PCHROM_CS_L0.810––
TP_USB_FIXT1_N0.484––
TP_USB_FIXT1_P0.488––
TP_USB3_EXTC_D2R_N0.351––
TP_USB3_EXTC_D2R_P0.347––
TP_USB3_EXTC_R2D_C_N0.332––
TP_USB3_EXTC_R2D_C_P0.333––
TP_USBC_PP20V_XAOL––
TP_USBC_PP20V_XBOL––
TP_WLAN_JTAG_SEL0.546––
TP_WLAN_JTAG_TCK0.547––
TP_WLAN_JTAG_TRST_L0.546––
TPAD_3V3_ACTUATOR_DISABLE_L0.9315––
TPAD_3V3_SPI_EN0.5823––
TPAD_3V3_SPI_INT_L0.9206––
TPAD_ACTUATOR_DISABLE_L0.485––
TPAD_KBD_WAKE_L0.4609––
TPAD_SPI_EN0.476––
TPADP3V3_IOUTOL––
TPADP5V_IOUTOL––
TPS62180_FB1.420––
TPS62180_FB_R0.353––
TPS62180_SS0.539––
U9600_CAP_CTRLOL––
UART_BT_BUF_CTS_L0.550––
UART_BT_BUF_D2R0.548––
UART_BT_BUF_R2D0.546––
UART_BT_BUF_RTS_L0.549––
UART_BT_LH_D2R0.475––
UART_BT_LH_R2D0.474––
UART_SE_D2R0.640––
UART_SE_D2R_CTS_L0.480––
UART_SE_R2D0.484––
UART_SE_R2D_RTS_L0.482––
UART_WLAN_D2R0.478––
UART_WLAN_D2R_CTS_L0.482––
UNUSED_EADC1CH2_ISNSOL––
UNUSED_EADC2CH2_ISNSOL––
UNUSED_EADC2CH5_ISNSOL––
UPC_I2C_INT_L0.4570––
UPC_PMU_RESET0.645––
UPC_X_SPI_CS_L0.580––
UPC_XA_FAULT_L0.684––
UPC_XA_FAULT_L_R0.686––
UPC_XA_R_OSC0.472––
UPC_XA_RESET0.001––
UPC_XA_SER_DBG0.6458––
UPC_XA_SS0.584––
UPC_XA_SWD_CLK0.606––
UPC_XA_SWD_DATA0.721––
UPC_XA_UART_RX0.5462––
UPC_XA_UART_TX0.5459––
UPC_XA_VDDIO_CFG0.587––
UPC_XB_FAULT_L0.688––
UPC_XB_FAULT_L_R0.684––
UPC_XB_R_OSC0.469––
UPC_XB_RESET0.000––
UPC_XB_SER_DBG0.6839––
UPC_XB_SPI_CLK0.575––
UPC_XB_SPI_CS_L0.603––
UPC_XB_SPI_MISO0.605––
UPC_XB_SPI_MOSI0.608––
UPC_XB_SWD_CLK0.596––
UPC_XB_SWD_DATA0.711––
UPC_XB_VDDIO_CFG0.580––
USB_EXTA_N0.4546––
USB_EXTA_P0.4549––
USB_SOC_DEBUG_NOL––
USB_SOC_DEBUG_POL––
USB_SOC_N0.727––
USB_SOC_P0.725––
USB_SOC_TYPEC_N0.720––
USB_SOC_TYPEC_P0.719––
USB2_UPC_PCH_XA_F_N0.494––
USB2_UPC_PCH_XA_F_P0.493––
USB2_UPC_PCH_XA_N0.494––
USB2_UPC_PCH_XA_P0.493––
USB2_UPC_PCH_XB_N0.491––
USB2_UPC_PCH_XB_P0.493––
USB3_BSSB_D2R_N0.349––
USB3_BSSB_D2R_P0.347––
USB3_BSSB_D2R_R_N0.350––
USB3_BSSB_D2R_R_P0.347––
USB3_BSSB_R2D_C_N0.334––
USB3_BSSB_R2D_C_P0.335––
USB3_BSSB_R2D_N0.704––
USB3_BSSB_R2D_P0.705––
USB3_EXTD_D2R_N0.3328––
USB3_EXTD_D2R_P0.3324––
USB3_EXTD_R2D_C_N0.3105––
USB3_EXTD_R2D_C_P0.3123––
USBC_X_RESET_L0.669––
USBC_XA_CC10.5878––
USBC_XA_CC20.595––
USBC_XA_D2R_CR_N<1>OL––
USBC_XA_D2R_CR_N<2>OL––
USBC_XA_D2R_CR_P<1>OL––
USBC_XA_D2R_CR_P<2>OL––
USBC_XA_R2D_N<1>OL––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<1>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_SBU10.667––
USBC_XA_SBU20.6481––
USBC_XA_USB_BOT_N0.774––
USBC_XA_USB_BOT_P0.777––
USBC_XA_USB_TOP_N0.7582––
USBC_XA_USB_TOP_P0.777––
USBC_XB_CC10.5855––
USBC_XB_CC20.587––
USBC_XB_D2R_CR_N<1>OL––
USBC_XB_D2R_CR_N<2>OL––
USBC_XB_D2R_CR_P<1>OL––
USBC_XB_D2R_CR_P<2>OL––
USBC_XB_R2D_N<1>OL––
USBC_XB_R2D_N<2>OL––
USBC_XB_R2D_P<1>OL––
USBC_XB_R2D_P<2>OL––
USBC_XB_SBU10.666––
USBC_XB_SBU20.665––
USBC_XB_USB_BOT_N0.772––
USBC_XB_USB_BOT_P0.774––
USBC_XB_USB_TOP_N0.774––
USBC_XB_USB_TOP_P0.7779––
UVP_DIS_L0.580––
VR0V9_IND_TBT_X0.2770.900–
WLAN_CONTEXT_A0.560––
WLAN_CONTEXT_B0.553––
WLAN_OP_ENOL––
WLAN_PWR_EN0.768––
WLAN_SROM_CLK0.553––
WLAN_SROM_CS0.578––
WLAN_SROM_CS_R0.542––
WLAN_SROM_DIN0.591––
WLAN_SROM_DOUT0.555––
WLAN_SROM_ORGOL––
WLAN_THROTTLE0.475––
WLANBTP1V8_IOUTOL––
WLANBTP3V3_IOUTOL––
XDP_BPM_L<0>0.307––
XDP_CPU_PRDY_L0.2578––
XDP_CPU_PREQ_L0.2704––
XDP_CPU_PWRBTN_L0.7629––
XDP_CPU_TCK0.0447––
XDP_DBRESET_L0.8010––
XDP_DP_INT_HPD0.588––
XDP_PCH_OBSDATA_A00.825––
XDP_PCH_OBSDATA_A10.828––
XDP_PCH_OBSDATA_A20.827––
XDP_PCH_OBSDATA_A30.828––
XDP_PCH_OBSDATA_B00.829––
XDP_PCH_OBSDATA_D10.827––
XDP_PCH_OBSDATA_D20.826––
XDP_PCH_OBSDATA_D30.827––
XDP_PCH_OBSFN_C10.825––
XDP_PCH_TCK0.3081––
XDP_PCH_TDI0.2363––
XDP_PCH_TDO0.2260––
XDP_PCH_TMS0.2352––
XDP_PCH_TRST_L0.2868––
XDP_PM_RSMRST_L1.2811––
XDP_PRESENT_CPU1.1362––
XDP_PRESENT_L0.4441––
XDP_USB_EXTD_OC_L0.811––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01598?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01598: diode 0.474, voltage 12.600. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-01598?

OpenBoardData's known-good values for PP3V3_G3H on the 820-01598: diode 0.420, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01598?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01598: diode 0.3620. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01598 board?

Open your own 820-01598 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License