Apple laptop board · OpenBoardData

820-3332 known-good readings

Known-good readings for the Apple laptop board 820-3332: 1,729 nets, including 114 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 112 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3332.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 114 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.333.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on this board; the "G3H" suffix, from the name, marks it as an always-on supply. Known-good readings in the archive are diode 0.33 and voltage 3.400. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.33 suggests a short or leaky load on the rail; a voltage well below 3.400 points to the supply or its load. No known-good resistance reading is available here, so compare against a matching net or a known-good board.

PPBUS_G3H0.445––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main bus rail that feeds the G3H (always-on) power stage on the 820-3332; that role comes from the rail's name, not from a schematic here. The only known-good figure in the readings archive is a diode reading of 0.445 to ground, with no condition recorded; there is no known-good voltage or resistance value here. Check it with the board unpowered in diode mode from PPBUS_G3H to ground, then power up and measure the DC voltage on the rail. A diode reading far from 0.445 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a bad part.

PPBUS_G3H_R0.453––
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R — the G3H in the name means this rail is always on (present whenever the charger or battery supplies the board), so it's an early rail to confirm before anything downstream.

  • Known-good reading: diode 0.453 (community archive, guide only; condition not recorded). No known-good voltage or resistance value here.
  • Check it: power off and unplug, then diode mode from PPBUS_G3H_R to ground. Then apply power and measure the rail's voltage.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; an open or very high reading points to a broken connection or missing supply. Confirm with a voltage check before replacing anything.
PPDCIN_G3HOL20.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, as its name indicates. The archive lists a known-good diode reading of OL to ground and a voltage of 20.000 V; these are community readings and a guide only. Check it unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far below OL suggests a short or leak on the rail; no known-good resistance reading is available here.

PPDCIN_G3H_CHGR0.642––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in the name marks it as an always-on startup rail, and CHGR ties it to the charger circuit. The only known-good reading here is a diode value of 0.642, with no condition recorded and no known-good voltage or resistance reading. Check it with the board unpowered in diode mode from the rail to ground, then measure the DC voltage on it with the charger connected. A diode reading far from 0.642 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPDCIN_G3H_INRUSH0.642––
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is an always-on startup rail, judging from the G3H part of its name (general naming convention, not from board data). The archive lists one known-good diode reading of 0.642, with no condition noted. Check it with the board unpowered in diode mode from the net to ground, then measure its voltage with power applied. No known-good voltage reading exists here, so compare against the matching net on a known-good board. A diode reading far from 0.642 usually points to a short or open on that net, but confirm with a voltage check before replacing anything.

PPDCIN_G3H_ISOLOL20.320–
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL — the name indicates the isolated DC input rail, and the G3H suffix marks it as an always-on startup rail (from the name).

  • Known-good readings in the archive: diode mode to ground OL, voltage 20.320. These are community readings and only a guide.
  • To check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • A diode reading far below OL or a voltage well off 20.320 usually points to a short or a fault on the input path, but a single reading doesn't confirm a bad part.
  • No known-good resistance reading is recorded for this rail.
PPVBAT_G3H_CHGR_R0.450––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; from the name, "G3H" means it's always-on whenever the charger is connected, and "CHGR" ties it to the charger circuit. The only known-good reading here is a diode value of 0.450, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered and the charger and battery disconnected, in diode mode from the rail to ground, then power up on the charger and measure the voltage on the rail. A diode reading far from 0.450 usually points to a short or leak on the rail or a fault in the charger side feeding it, but one reading alone doesn't confirm a bad part.

PPVBAT_G3H_CHGR_REG0.450––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG — reference note

  • From the name: a battery/charger-side rail (PPVBAT, CHGR) that is G3H, meaning it should be present whenever the board has power, not just after the power button.
  • Known-good reading in the archive: diode mode to ground 0.450, with no condition recorded. That is the only value recorded for this rail; there is no known-good voltage or resistance reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage on the rail.
  • A diode reading far below 0.450 suggests a short or a leaky part on the rail; far above it suggests an open connection or a missing component. Confirm with a second measurement before replacing anything, since a single reading can mislead.
PPVBAT_G3H_CONNOL––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judged from the name (PP = power rail, VBAT = battery, G3H = always on). The only archived reading is a diode value of OL to ground; there is no known-good voltage reading for this rail here.

  • Check it unpowered, in diode mode to ground, at the connector; OL is the archived guide value, not a spec.
  • Then apply power and measure the voltage on the same point.
  • A diode reading far below OL usually points to a short or a leaky part on that net; a voltage that is missing or wrong points to the battery/charger path feeding it.

These are general checks, and the archived reading varies with board state, so treat it as a guide rather than a confirmed fault.

PPVIN_G3H_P3V42G3H0.599––
AI: what PPVIN_G3H_P3V42G3H is and how to check it
  • What it is: From the name, this is the always-on G3H input rail feeding the P3V42G3H supply on the 820-3332 — an early, always-present rail in the startup sequence.
  • Known-good reading: Diode 0.599 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from the rail to ground and compare with 0.599. Then apply power and measure the voltage on the rail.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open connection. Confirm with voltage before replacing anything.
PPVOUT_G3_PCH_DCPRTC0.635––
AI: what PPVOUT_G3_PCH_DCPRTC is and how to check it
  • What it is: PPVOUT_G3_PCH_DCPRTC is an always-on G3H rail feeding the PCH, judging from the name (VOUT, G3, PCH). The name alone doesn't say what generates it.
  • Known-good reading: diode 0.635 in the readings archive, with no condition recorded. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.635 suggests a short or a leaky load on the rail; well above suggests an open path. Confirm with a second measurement before suspecting a part.
PPVRTC_G3H0.459––
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on RTC rail; the "G3H" suffix, from the name, marks it as a startup-stage rail that stays up whenever the board has power. The archive lists one known-good diode reading, 0.459, with no condition noted; there is no known-good voltage reading here. Check it in diode mode to ground with the board unpowered, then measure the voltage with power applied and compare against a known-good board for that rail. A diode reading far from 0.459 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

S5 and SUS: standby 14

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.516––
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: PP1V2_S5_SMC_VDDC is a 1.2 V rail, from its name. The S5 and SUS parts indicate it belongs to the standby (suspend-to-RAM) domain, so it should be present whenever the board has standby power.
  • Known-good reading: diode 0.516 to ground, from the readings archive. This is a community guide, not a factory spec.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.516. Then apply power and measure the voltage; no known-good voltage reading is available here, so expect about 1.2 V from the name and confirm against a known-good board.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; an open or high reading suggests a missing feed or a broken connection. No resistance reading is known here.
PP1V05_SUS0.494––
AI: what PP1V05_SUS is and how to check it
  • What it is: PP1V05_SUS is a 1.05 V standby rail; the "SUS"/S5 part of the name indicates it's a standby rail, present before full power-on. That's from the name, not from board data.
  • Known-good reading: diode 0.494 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V05_SUS to ground; then power up in standby and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a voltage check before suspecting any part.
PP3V3_S50.142––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the "S5" in the name marks it as a standby-stage supply that should be present before the board fully powers on. The only known-good reading here is a diode value of 0.142 to ground, with no condition stated; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then apply power and measure the voltage at the rail. A diode reading far from 0.142 usually points to a short or a leaky load on the rail rather than the regulator itself, but one reading isn't proof — compare against a matching standby rail or a known-good board before replacing anything.

PP3V3_S5_AVREF_SMC0.609––
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC — from its name, a 3.3 V standby (S5) reference rail feeding the SMC's analog reference. It sits in the standby stage, so it should be present whenever the board has standby power.

  • Known-good: diode-to-ground 0.609 (community reading, a guide only; no condition recorded). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on the net, black on ground, compare with 0.609.
  • Then power with the charger connected and measure the voltage on the net; expect about 3.3 V, though no known-good voltage is recorded here.
  • A diode reading far below 0.609 suggests a short or a leaky part on the rail; far above suggests an open path. Confirm with a voltage measurement before replacing anything.
PP3V3_S5_SMC_VDDA0.324––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply; the S5 part of the name marks it as a standby-stage rail (from the name).

  • Known-good: diode 0.324 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage.
  • A diode reading far from 0.324 usually points to a short or a leaky part on the rail, but one reading isn't proof — compare with a matching net or a known-good board before replacing anything.
PP3V3_SUS0.343––
AI: what PP3V3_SUS is and how to check it
  • PP3V3_SUS is a 3.3 V standby rail; the "SUS" in the name marks it as a standby rail (general naming convention, not from this board's data).
  • Known-good from the readings archive: diode 0.343 to ground. No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.343. Then power up and measure the voltage.
  • A diode reading far below known-good usually points to a short or a leaky part on the rail; far above can mean an open path. One reading isn't proof, so confirm with the voltage and a second measurement before replacing anything.
PP5V_S50.4605.000–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the main rails come up. Known-good readings in the archive are a diode value of 0.460 and 5.000 V, with no condition recorded, so treat them as a guide only.

  • Check it unpowered in diode mode from PP5V_S5 to ground; a much lower reading than 0.460 suggests a short or a leaky load on the rail.
  • Then power the board and measure the voltage; it should sit near 5.000 V once standby is up.
  • No known-good resistance reading exists here, so compare against a matching standby rail or a known-good board of the same model.

A voltage well below 5 V with a normal diode reading usually points to the standby supply or its enable, not a shorted load.

PP5V_S5_P5VSUSFET_R0.459––
AI: what PP5V_S5_P5VSUSFET_R is and how to check it

PP5V_S5_P5VSUSFET_R — from the name, a 5 V standby rail (S5/SUS) on the source side of a P5VSUS FET; the exact parts on it aren't documented here.

  • Known-good: diode reading 0.459 to ground, board unpowered. No known-good voltage is listed for this rail.
  • Check: power off, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • A diode reading far below 0.459 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with a voltage check before replacing anything.
PP5V_S5RS4_CUMULUS0.457––
AI: what PP5V_S5RS4_CUMULUS is and how to check it
  • What it is: PP5V_S5RS4_CUMULUS is a 5 V standby rail. From the name, S5/SUS means it belongs to the standby stage, so it should be present whenever the board has standby power.
  • Known-good reading: diode 0.457 to ground, from the readings archive. That is a community guide, not a factory value; no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.457. Then apply power and measure the DC voltage on the rail; it should sit near 5 V.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken connection or missing part. No voltage at all points back to the standby supply that feeds it.
PP5V_SUS0.407––
AI: what PP5V_SUS is and how to check it

PP5V_SUS is the 5 V standby rail; the "SUS" in its name indicates it belongs to the standby/suspend power state, and "S5" marks it as a startup-stage rail. The only known-good reading here is a diode value of 0.407 to ground; no known-good voltage reading is recorded. Check it with the board unpowered in diode mode from PP5V_SUS to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.407 usually points to a short or a faulty component on that rail, but a single reading isn't proof a part is bad.

PP5V_SUS_PCH_V5REFSUS0.398––
AI: what PP5V_SUS_PCH_V5REFSUS is and how to check it

PP5V_SUS_PCH_V5REFSUS — from the name, a 5 V standby rail feeding the PCH's 5 V reference supply. The name also marks it as S5/SUS, so it should be present in standby, before the board fully powers on.

  • Known-good: diode 0.398 (archive reading, guide only; condition not recorded).
  • Check: board unpowered, diode mode, black probe to ground, red on the rail. Then apply power and measure the voltage in standby.
  • No known-good voltage reading here, so compare against a matching rail or a known-good board.
  • A diode reading far below 0.398 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PPVIN_S5_HS_COMPUTING_ISNS0.443––
AI: what PPVIN_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From the name, PPVIN_S5_HS_COMPUTING_ISNS is a high-side current-sense input for the S5 (standby) computing supply — a sense line, not a power rail you'd load. The board data lists it at the S5/SUS standby stage.
  • Known-good reading: diode 0.443 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the net — compare to 0.443. Then power up and measure the voltage on it.
  • If it's far off: a much lower diode reading suggests a short or a failed part on that sense line; a much higher one suggests an open. A single reading isn't proof — confirm with the voltage measurement and compare against a matching net before replacing anything.
PPVIN_S5_HS_GPU_ISNS0.445––
AI: what PPVIN_S5_HS_GPU_ISNS is and how to check it
  • What it is: From the name, PPVIN_S5_HS_GPU_ISNS is a high-side GPU current-sense (ISNS) input on an S5 standby-stage rail. The exact parts on the net aren't known here.
  • Known-good reading: diode 0.445 to ground, from the readings archive (a community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the net to ground and compare with 0.445; then power up and measure the voltage on the net.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the net, but one reading doesn't confirm a bad part. Check the voltage next, and compare with a matching sense net or a known-good board.
PPVIN_S5_HS_OTHER_ISNS0.445––
AI: what PPVIN_S5_HS_OTHER_ISNS is and how to check it
  • What it is: From the name, PPVIN_S5_HS_OTHER_ISNS is a high-side current-sense input on an S5 (standby) rail. "PPVIN" suggests a main input supply, "ISNS" a current-sense point.
  • Known-good reading: Diode mode to ground is 0.445, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: Power off, then measure diode mode from the net to ground. Then power up and measure the voltage on the net.
  • If it's far off: A diode reading well below 0.445 can suggest a short or leaky part on that net; well above can suggest an open. Confirm with a voltage check before replacing anything.

S4 5

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.423––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging from its name (general naming, not from board data). The only known-good reading here is a diode value of 0.423; no voltage or resistance reading is recorded for this rail.

  • With the board unpowered, measure diode mode from PP3V3_S4 to ground and compare with 0.423. A much lower reading suggests a short or a leaky load on the rail; a much higher one can mean an open path.
  • Then apply power and check the rail sits near 3.3 V once the S4 stage is reached. A rail that never comes up points to the upstream enable or the regulator feeding it, not necessarily the rail itself.
  • Community readings vary with board state, so treat 0.423 as a guide and confirm against a matching rail or a known-good board before replacing anything.
PP3V3_S4_TBT0.426––
AI: what PP3V3_S4_TBT is and how to check it

PP3V3_S4_TBT is a 3.3 V rail, and the S4 in its name marks it as a startup-stage rail (both from the name). The only known-good reading here is a diode value of 0.426 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered.
  • A diode reading far from 0.426 usually points to a short or a damaged load on the rail, but one reading isn't proof a part is bad.
  • With no known-good voltage listed, compare against a matching rail on a known-good board rather than guessing.
PP5V_S40.425––
AI: what PP5V_S4 is and how to check it
  • PP5V_S4 is a 5 V rail in the S4 startup stage, from its name. The only known-good reading here is a diode value of 0.425; no voltage or resistance reading is recorded.
  • Check it unpowered in diode mode, black probe to ground, red to the rail, and compare with 0.425. Then power the board and measure the DC voltage, which should be about 5 V.
  • A diode reading far below 0.425 suggests a short or a low-impedance load on the rail; far above it suggests an open path. A missing or low voltage under power points to the rail not being enabled or its source failing.
  • These readings are community guides and vary with board state, so confirm on a known-good board before replacing anything.
PP5V_S4_AUDIO_XW0.421––
AI: what PP5V_S4_AUDIO_XW is and how to check it
  • What it is: A 5 V rail for the audio section, in the S4 power state — that's from the name, not from a schematic.
  • Known-good: diode reading of 0.421 to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with voltage before replacing anything.
PP5V_S4_CUMULUS0.457––
AI: what PP5V_S4_CUMULUS is and how to check it

PP5V_S4_CUMULUS — 820-3332

  • What it is: a 5 V rail in the S4 power state, from the name; "CUMULUS" is the rail's label, not a part. S4 is a later stage in the startup sequence, so it should only come up after the earlier rails are good.
  • Known-good reading: diode 0.457 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail — compare with 0.457. Then power up and measure the voltage; a healthy S4 5 V rail should sit near 5 V (general expectation, not a board value).
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken path or missing part. A correct diode reading with no voltage points upstream — check whether the earlier rails and the S4 enable are present first.

S3: memory 20

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V75_S3_MEM_VREFCA_A0.424––
AI: what PP0V75_S3_MEM_VREFCA_A is and how to check it
  • What it is: From the name, a 0.75 V memory reference rail (VREFCA) that comes up at the S3 (memory) stage. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.424 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 0.75 V from the name.
  • If it's far off: a low diode reading suggests a short or leaky part on the rail; a correct diode reading with wrong voltage points upstream at the rail's supply or enable. Treat that as a likely cause, not confirmed.
PP0V75_S3_MEM_VREFCA_B0.423––
AI: what PP0V75_S3_MEM_VREFCA_B is and how to check it

PP0V75_S3_MEM_VREFCA_B — reference note

  • From the name: a 0.75 V memory reference rail (PP = power rail, 0V75 = 0.75 V, S3 = memory suspend state, VREFCA = DRAM reference for the CA bus). This is general naming, not from board data.
  • Known-good: diode-to-ground 0.423 in the readings archive. That's a community guide, not a spec, and the archive gives no known-good voltage for this rail.
  • Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and in S3.
  • A diode reading far below 0.423 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with a voltage check and compare against a matching rail before replacing anything.
PP0V75_S3_MEM_VREFDQ_A0.412––
AI: what PP0V75_S3_MEM_VREFDQ_A is and how to check it
  • What it is: From the name, a 0.75 V memory reference rail (VREFDQ) that comes up at the S3 (memory) stage. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.412 in the archive. This is a community guide, not a factory spec; no voltage or resistance value is known here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure the voltage. Compare the diode reading with 0.412.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher one suggests an open trace or missing connection. One reading alone doesn't confirm a bad part, so check the voltage too.
PP0V75_S3_MEM_VREFDQ_B0.407––
AI: what PP0V75_S3_MEM_VREFDQ_B is and how to check it

PP0V75_S3_MEM_VREFDQ_B is a 0.75 V memory reference rail; the "S3" and "MEM" parts of the name indicate it belongs to the memory section and comes up in the S3 (suspend-to-RAM) power state, and "VREFDQ" indicates it's the reference for the memory data lines. The archive lists a diode reading of 0.407 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.407 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP1V5_S3_CPU_VCCDQ0.106––
AI: what PP1V5_S3_CPU_VCCDQ is and how to check it

PP1V5_S3_CPU_VCCDQ is a 1.5 V rail; the S3 in its name places it in the memory stage of startup, and the VCCDQ part suggests it feeds the CPU's memory-interface supply (that part is general naming, not from board data). The archive's only known-good figure is a diode reading of 0.106 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.106 usually points to a short or a leaky part on the rail, while a correct diode reading but missing voltage points back at the rail's supply or enable. Treat 0.106 as a guide only, since community readings vary with board state.

PP1V5_S3RS0_CPUDDR0.102––
AI: what PP1V5_S3RS0_CPUDDR is and how to check it

PP1V5_S3RS0_CPUDDR is a 1.5 V memory rail; the S3 and CPUDDR parts of the name indicate it belongs to the memory stage. The only known-good reading here is a diode value of 0.102 to ground, with no condition recorded. Check it with the board unpowered in diode mode, probe to ground, then measure the voltage with power applied; no known-good voltage reading is available for this rail. A diode reading far from 0.102 usually points to a short or a damaged part on the rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V5_S3RS0_FET0.106––
AI: what PP1V5_S3RS0_FET is and how to check it

PP1V5_S3RS0_FET — from the name, a 1.5 V rail in the S3 (memory) startup stage, switched through a FET. The archive lists one known-good diode reading of 0.106 to ground; there is no known-good voltage or resistance reading here.

  • Check it unpowered: board off and unplugged, multimeter in diode mode, black probe on ground, red on the rail. Compare with 0.106; a much lower reading suggests a short on the rail, a much higher one an open path.
  • Then check it powered: measure the voltage on the rail with the board running and compare against 1.5 V from the name — that figure is general, not a recorded reading.
  • A reading far from known-good usually points to a shorted load or a failed switching FET, but one reading doesn't confirm a bad part.
PP1V5R1V35_S30.224––
AI: what PP1V5R1V35_S3 is and how to check it
  • What it is: From the name, PP1V5R1V35_S3 is a memory-stage (S3) rail that supplies 1.5 V and 1.35 V. Which parts sit on it isn't known here.
  • Known-good reading: diode 0.224 in diode mode to ground, board unpowered. No known-good voltage or resistance reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.224. Then power up and measure the rail voltage; it should sit near its named 1.5 V / 1.35 V levels, though no known-good voltage is recorded.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail, a much higher one to an open path. Treat 0.224 as a guide only, since readings vary with board state, and confirm before replacing anything.
PP3V3_S30.396––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is a 3.3 V rail that, from its name, belongs to the S3 (memory) startup stage on the 820-3332. The only known-good reading in the archive is a diode value of 0.396 to ground; there is no known-good voltage or resistance value here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.396 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything.

PP3V3_S3_DPMUX_UC_R0.39––
AI: what PP3V3_S3_DPMUX_UC_R is and how to check it
  • What it is: A 3.3 V rail, from the name: PP3V3 = 3.3 V supply, S3 = memory-stage power (general naming convention, not from this board's data). DPMUX_UC_R suggests a display-mux related branch; the exact parts on it aren't documented here.
  • Known-good reading: diode 0.39 to ground, from the readings archive (community value, a guide only, no condition recorded). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.39; then power on and measure the voltage, which should sit near 3.3 V.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; an open or high reading points to a missing feed or broken trace. Confirm with a second measurement before replacing anything.
PP3V3_S3_PSOC0.427––
AI: what PP3V3_S3_PSOC is and how to check it

PP3V3_S3_PSOC is a 3.3 V rail in the S3 (memory) power stage, judged from its name; the PSOC suffix suggests it also feeds a PSOC device, though the parts on the net aren't known.

  • Known-good: diode 0.427 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.427.
  • Then power up and measure the voltage; expect about 3.3 V, but that figure is general, not from this board's data.
  • A diode reading far below known-good usually points to a short or a failing part on the rail; far above can mean an open path. Confirm with voltage before replacing anything.
PP3V3_S3_VREFMRGN_CTRLOL––
PP3V3_S3_VREFMRGN_DAC0.396––
AI: what PP3V3_S3_VREFMRGN_DAC is and how to check it

PP3V3_S3_VREFMRGN_DAC (820-3332)

  • What it is: From the name, a 3.3 V rail that is present in the S3 (memory) power stage, carrying a reference/margin DAC signal. The exact parts on the net aren't known here.
  • Known-good reading: diode 0.396 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: Power off, measure diode mode from the net to ground; then power on and measure the DC voltage, comparing against a matching net or a known-good board.
  • If far off: a much lower diode reading usually points to a shorted load or damaged part on the net; a much higher one to an open trace or missing component. Confirm with a voltage measurement before replacing anything.
PP3V3_S3RS4_BT_F0.429––
AI: what PP3V3_S3RS4_BT_F is and how to check it

PP3V3_S3RS4_BT_F is a 3.3 V rail; the S3 in its name marks it as a memory-stage rail, and the BT_F suffix suggests it feeds the Bluetooth section (that part is from the name, not from board data). The only known-good reading here is a diode value of 0.429 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far from 0.429 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S30.452––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is the 5 V rail for the S3 (memory) power state, judged from its name. The only archived reading is a diode value of 0.452 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.452 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP5V_S3_ALSCAMERA_F0.448––
AI: what PP5V_S3_ALSCAMERA_F is and how to check it
  • What it is: From the name, PP5V_S3_ALSCAMERA_F is a 5 V rail that comes up in the S3 (memory/suspend) power stage and feeds the camera circuit. The exact parts on it aren't known here.
  • Known-good reading: diode 0.448 to ground, from the readings archive. This is a community guide, not a factory spec, and the data lists no condition and no known-good voltage for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.448; then power up and measure the voltage, comparing against a known-good board since no voltage value is recorded.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail, while a missing voltage with a normal diode reading points upstream to the rail's enable or source. Confirm with a second measurement before replacing anything.
PP5V_S3_DEBUG_ADC_AVDD_FILTOL––
AI: what PP5V_S3_DEBUG_ADC_AVDD_FILT is and how to check it

PP5V_S3_DEBUG_ADC_AVDD_FILT is a filtered 5 V rail that, from its name, belongs to the S3 (memory) power stage and feeds a debug/ADC supply. The only archived reading is a diode-mode value of OL to ground, with no condition recorded and no voltage or resistance values here. Check it unpowered in diode mode from the net to ground, then measure its DC voltage with the board powered. A far-off diode reading or missing voltage usually points to a short or open on that rail or its source, but OL alone isn't proof of a fault; compare against a known-good board.

PP5V_S3_LTUSB_A_F0.490––
AI: what PP5V_S3_LTUSB_A_F is and how to check it

PP5V_S3_LTUSB_A_F is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state and feeds the LTUSB_A section — likely a USB-A port supply; that's from the name, not confirmed by board data. The only known-good reading here is a diode value of 0.490 to ground; no known-good voltage reading is recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.490 suggests a short or leaky part on the rail; a much higher or open reading points to a broken connection. Confirm with a voltage measurement under power before replacing anything.

PP5V_S3_LTUSB_A_ILIM0.482––
AI: what PP5V_S3_LTUSB_A_ILIM is and how to check it
  • What it is: From the name, PP5V_S3_LTUSB_A_ILIM is a 5 V rail that comes up at the S3 (memory) stage and sets the current limit for a USB-A port. Which parts sit on it isn't known here.
  • Known-good reading: diode 0.482 to ground, from the readings archive. That's a community guide, not a factory value, and no voltage or resistance value is known here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good often points to a shorted part on the rail; a much higher one to an open path. Confirm with a voltage check under power before replacing anything.
PPVTTDDR_S3OL––
AI: what PPVTTDDR_S3 is and how to check it

PPVTTDDR_S3 is a memory (DDR) termination rail; the S3 in the name marks it as a memory startup-stage rail, and the VTTDDR part indicates DDR termination voltage. The only known-good reading here is a diode-mode value of OL to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure the voltage and compare against a known-good board, since no voltage value is recorded here. A diode reading far from OL, or a voltage that is missing or wrong, usually points to a short or a failed regulator feeding the rail, but that is a likely cause, not a confirmed one.

S0: running 62

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V75_S0_DDRVTT0.165––
AI: what PP0V75_S0_DDRVTT is and how to check it

PP0V75_S0_DDRVTT is a 0.75 V DDR termination rail; the "0.75" and "DDRVTT" come from the name, and "S0" means it's up in the running state. The only known-good reading here is diode 0.165 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.165 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP1V0_S0GPU_ISNS0.138––
AI: what PP1V0_S0GPU_ISNS is and how to check it

PP1V0_S0GPU_ISNS is a 1.0 V GPU current-sense rail; the S0 in the name indicates it belongs to the running state. The only archived reading is a diode value of 0.138, with no condition recorded, so treat it as a guide. With the board unpowered, measure diode mode from the rail to ground and compare with 0.138; then apply power and check the voltage, for which there is no known-good reading here. A diode reading far below 0.138 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path; confirm with a second measurement before replacing anything.

PP1V05_PCHVCCIO_S00.046––
AI: what PP1V05_PCHVCCIO_S0 is and how to check it

PP1V05_PCHVCCIO_S0 is the 1.05 V PCH VCCIO rail, enabled in the S0 (running) state, judging from the rail name. The archive lists a known-good diode reading of 0.046 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.046; then power up and check the voltage is present in S0. A diode reading far from 0.046 usually points to a short or a faulty part on the rail, but a single reading isn't proof, so confirm before replacing anything.

PP1V05_S00.011––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail, and the S0 suffix in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.011 to ground; there is no known-good voltage reading in this data.

  • Check it with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.011.
  • Then power the board and measure the DC voltage on the rail.
  • A diode reading far from 0.011 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything.
PP1V5_S00.376––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" suffix comes from its name and indicates it is active in the running (S0) state. The only known-good reading in the archive is a diode value of 0.376 to ground, with no condition recorded. Check it with the board unpowered in diode mode from PP1V5_S0 to ground, then power up and measure the voltage. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from 0.376 usually points to a short or a faulty component on the rail, but confirm with voltage and resistance checks before replacing anything.

PP1V5_S0_AUDIO_DIG0.377––
AI: what PP1V5_S0_AUDIO_DIG is and how to check it

PP1V5_S0_AUDIO_DIG is a 1.5 V digital audio rail; the "S0" part of the name indicates it belongs to the running (S0) state, and this is from the name rather than from circuit data.

  • Known-good reading: diode 0.377 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • To check it: power off, measure diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.377 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault; compare with a matching rail or a known-good board before replacing anything.
PP1V05_S0_CPU_VCCPQE0.012––
AI: what PP1V05_S0_CPU_VCCPQE is and how to check it
  • What it is: From the name, PP1V05_S0_CPU_VCCPQE is a 1.05 V rail that runs in the S0 (running) state and feeds the CPU's VCCPQE domain. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.012 to ground, with no condition noted. That's a very low diode reading, so treat it as a guide from community data, not a spec. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a much higher diode reading usually points to an open trace or missing part; a short to ground points to a failed component on the rail. Confirm with a second measurement before replacing anything.
PP1V5_S0_LDO0.565––
AI: what PP1V5_S0_LDO is and how to check it

PP1V5_S0_LDO is a 1.5 V low-dropout rail, from its name; the S0 suffix marks it as a running-state rail. The archive lists one known-good reading: diode 0.565, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.565 usually points to a short or leaky part on the rail, but one reading alone doesn't confirm a bad part.

PP1V05_S0_P1V05TBTFET0.046––
AI: what PP1V05_S0_P1V05TBTFET is and how to check it

PP1V05_S0_P1V05TBTFET is a 1.05 V rail that runs in the S0 (fully on) state, judging from its name; the "TBTFET" part likely refers to a Thunderbolt-related FET, but that's inference from the name, not from board data. The only known-good reading here is a diode value of 0.046 to ground, with no condition recorded and no voltage value available. Check it unpowered in diode mode to ground, then measure the voltage with the board powered in S0. A diode reading far from 0.046 usually points to a short or a damaged part on that rail, but a single reading isn't proof — confirm before replacing anything.

PP1V05_S0_PCH_VCCADPLLA_F0.041––
AI: what PP1V05_S0_PCH_VCCADPLLA_F is and how to check it
  • What it is: From the name, PP1V05_S0_PCH_VCCADPLLA_F is a 1.05 V rail for the PCH's VCCADPLLA supply, active in the S0 (running) state.
  • Known-good reading: Diode mode to ground is 0.041 in the readings archive. That's a community value and a guide only; no known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: A diode reading well below known-good often points to a shorted load on the rail; a missing or wrong voltage with power applied points to the supply or enable side. Confirm with a second measurement before replacing anything.
PP1V05_S0_PCH_VCCADPLLA_R0.041––
AI: what PP1V05_S0_PCH_VCCADPLLA_R is and how to check it

PP1V05_S0_PCH_VCCADPLLA_R — from the name, a 1.05 V rail that runs in the S0 (running) state and feeds the PCH's VCCADPLLA supply.

  • Known-good: diode-to-ground reading of 0.041 in the archive. That's a guide only; no voltage reading is recorded here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.041. Then power the board and measure the voltage at the rail.
  • A diode reading far from 0.041 usually points to a short or a leaky part on the rail, or an open feed; confirm with a second measurement before replacing anything.
  • No known-good voltage is listed, so compare the powered voltage against the rail's nominal 1.05 V and a matching rail on a known-good board.
PP1V05_S0_PCH_VCCADPLLB_F0.044––
AI: what PP1V05_S0_PCH_VCCADPLLB_F is and how to check it
  • What it is: From the name, PP1V05_S0_PCH_VCCADPLLB_F is a 1.05 V rail (PP1V05) that runs in the S0 (running) state, feeding the PCH VCCADPLLB supply. The name also suggests it's a filtered rail (the _F suffix).
  • Known-good reading: Diode mode to ground is 0.044, from the readings archive. That's a community guide value and varies with board state; no voltage or resistance known-good reading is available here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.044. Then power up and measure the DC voltage, which should be about 1.05 V once the board is in S0.
  • If it's far off: A much lower diode reading suggests a short or a leaky part on the rail; a much higher one can mean an open feed or a missing component. Confirm with the voltage measurement before suspecting any part.
PP1V05_S0_PCH_VCCADPLLB_R0.044––
AI: what PP1V05_S0_PCH_VCCADPLLB_R is and how to check it
  • What it is: From the name, a 1.05 V rail (PP1V05) that runs in the S0 (fully on) state and feeds the PCH VCCADPLLB supply. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.044 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a missing or wrong voltage with a normal diode reading points upstream, to the rail's supply or its enable. Confirm with a second measurement before replacing anything.
PP1V05_S0_PCH_VCCCLKDMI_F0.040––
AI: what PP1V05_S0_PCH_VCCCLKDMI_F is and how to check it

PP1V05_S0_PCH_VCCCLKDMI_F — reference note

  • From the name: a 1.05 V rail (PP1V05) that runs in S0 (board fully on) and feeds the PCH's VCCCLK/DMI section. The exact parts on the net aren't documented here.
  • Known-good reading in the archive: diode mode to ground 0.040 (board unpowered). No known-good voltage reading is recorded for this rail.
  • To check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.040. Then power up in S0 and measure the voltage; expect about 1.05 V from the name, though that figure isn't a recorded reading.
  • A diode reading far below 0.040 suggests a short or a leaky load on the rail; far above it suggests an open trace or missing load. Confirm with the powered voltage before suspecting any part.
PP1V05_S0_PCH_VCCCLKDMI_R0.046––
AI: what PP1V05_S0_PCH_VCCCLKDMI_R is and how to check it

PP1V05_S0_PCH_VCCCLKDMI_R — reference note

  • From the name: a 1.05 V rail (PP1V05) that runs in the S0 (fully on) state and feeds the PCH clock/DMI section. The exact parts on it aren't documented here.
  • Known-good reading in the archive: diode mode to ground 0.046, with no condition stated. No known-good voltage reading here.
  • To check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.046; then power up and measure the voltage, expecting about 1.05 V from the name.
  • A diode reading far below 0.046 suggests a short or a leaky load on the rail; far above it suggests an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP1V5_S0_RIO0.565––
AI: what PP1V5_S0_RIO is and how to check it

PP1V5_S0_RIO is a 1.5 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "RIO" is a rail label from the name. The archive lists one known-good diode reading of 0.565 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.565 suggests a short or leaky load on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.

PP1V5R1V35_S0GPU0.163––
AI: what PP1V5R1V35_S0GPU is and how to check it
  • What it is: A running-state (S0, from the name) GPU supply rail, nominally 1.5 V / 1.35 V from the name. This board's data doesn't list which parts sit on it.
  • Known-good reading: diode 0.163 to ground. That's the only value recorded here; there's no known-good voltage or resistance reading.
  • How to check: power off, measure diode mode from PP1V5R1V35_S0GPU to ground and compare with 0.163. Then power on and measure the rail voltage; no known-good voltage is recorded, so compare against a known-good board of the same model.
  • If it's far off: a much lower diode reading usually points to a shorted part on the rail, but that's a likely cause, not a confirmed one. Check the voltage next before replacing anything.
PP1V8_S00.117–308.500R
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail; the "S0" in its name indicates it belongs to the running (S0) power state. The archive lists a diode reading of 0.117 and a resistance of 308.500R, but no voltage reading is recorded here. With the board unpowered, check diode mode from PP1V8_S0 to ground and compare with 0.117; then power up and measure the rail voltage, which has no known-good value in this data. A diode reading far from 0.117 usually points to a short or a faulty part on the rail, but one reading alone doesn't confirm a bad component.

PP1V8_S0_CPU_VCCPLL_R0.121––
AI: what PP1V8_S0_CPU_VCCPLL_R is and how to check it

PP1V8_S0_CPU_VCCPLL_R is a 1.8 V rail feeding the CPU's PLL supply; the S0 in the name indicates it belongs to the running (S0) state, and the VCCPLL part says it powers the CPU clock/PLL section (from the name, general convention).

  • Known-good: diode 0.121 to ground, from the readings archive (community value, a guide only, no condition recorded).
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, compare to 0.121.
  • Then power up and measure the voltage; no known-good voltage reading is recorded here, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far below known-good usually points to a short or a failing part on the rail; far above can mean an open connection. One reading isn't proof, so confirm before replacing anything.
PP1V8_S0_P1V5_LDO0.118––
AI: what PP1V8_S0_P1V5_LDO is and how to check it
  • What it is: From the name, PP1V8_S0_P1V5_LDO is a 1.8 V rail that stays up in the S0 (running) state, fed by a 1.5 V LDO. The exact parts on it aren't known here.
  • Known-good reading: diode 0.118 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then power up and measure the DC voltage, which should sit near 1.8 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a voltage measurement before replacing anything.
PP3V3_S00.307––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judged from its name; the board data here has no part list for it. The only known-good reading is a diode value of 0.307 to ground, with no condition noted. Check it with the board unpowered in diode mode from PP3V3_S0 to ground, then measure the voltage with power applied and the board in S0. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.307 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0_CPUTHMSNS_R0.370––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it
  • What it is: From the name, PP3V3_S0_CPUTHMSNS_R is a 3.3 V S0 (running-state) rail feeding the CPU thermal sensor circuit. The exact parts on it aren't known here.
  • Known-good reading: diode 0.370 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.370. Then power up and measure the DC voltage; it should sit near 3.3 V, though no known-good figure is recorded.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open feed. Treat 0.370 as a community guide, not a guarantee, and confirm against a matching net or known-good board before replacing anything.
PP3V3_S0_DPMUX_UC_R0.30––
AI: what PP3V3_S0_DPMUX_UC_R is and how to check it
  • What it is: PP3V3_S0_DPMUX_UC_R is a 3.3 V rail, from its name; the S0 suffix marks it as a running-state rail (general naming convention, not from this board's data).
  • Known-good reading: diode 0.30 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If far from 0.30: a much lower diode reading usually suggests a short or a failing load on the rail; a much higher one can mean an open path. Confirm with the powered voltage before replacing anything.
PP3V3_S0_GPUTHMSNS_R0.357––
AI: what PP3V3_S0_GPUTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding a GPU thermal sensor circuit. The board data has no parts list, so the exact components on it aren't known.
  • Known-good reading: diode 0.357 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; an open or high reading suggests a broken feed. Confirm with a voltage check before replacing anything.
PP3V3_S0_PCH_VCC3_3_CLK_F0.309––
AI: what PP3V3_S0_PCH_VCC3_3_CLK_F is and how to check it
  • What it is: A 3.3 V rail, from the name: PP3V3 is the 3.3 V supply, S0 means it belongs to the running state, and PCH_VCC3_3_CLK_F points to the PCH clock section's 3.3 V feed. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0.309 to ground, from the readings archive. There's no known-good voltage or resistance value recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.309. Then power up and measure the voltage on the rail, which should sit near 3.3 V once the board is in S0.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher one suggests an open feed. A missing voltage with a normal diode reading points upstream, to whatever enables this rail, rather than to the rail itself. These are general guidelines, not confirmed causes.
PP3V3_S0_PCH_VCC3_3_CLK_R0.308––
AI: what PP3V3_S0_PCH_VCC3_3_CLK_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding the PCH's 3.3 V clock supply. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.308 to ground, from the readings archive (a community guide, not a spec). No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If it's far off: a low or shorted diode reading suggests a shorted load on the rail; a missing voltage with a normal diode reading points upstream to the rail's source or enable. Confirm with a second measurement before replacing anything.
PP3V3_S0_PCH_VCCA_DAC_F0.307––
AI: what PP3V3_S0_PCH_VCCA_DAC_F is and how to check it

PP3V3_S0_PCH_VCCA_DAC_F — reference note

  • What it is: from the name, a 3.3 V rail (PP3V3) that is up in the S0 running state, feeding the PCH's VCCA supply for the DAC section. The exact parts on it aren't documented here.
  • Known-good reading: diode mode to ground, board unpowered, 0.307. This is a community figure and only a guide; no known-good voltage reading is recorded for this rail.
  • How to check: power off and confirm no standby voltage, then measure diode mode from the rail to ground and compare with 0.307. Then power up and measure the DC voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open trace or missing connection. A wrong voltage with a normal diode reading points more to the supply side than the load.
PP3V3_S0_SSD_FLT0.306––
AI: what PP3V3_S0_SSD_FLT is and how to check it

PP3V3_S0_SSD_FLT (820-3332) — reference note

  • From its name, this is a 3.3 V rail (PP3V3) that is up in the S0 running state and is tied to the SSD, with FLT suggesting a fault or filter-related line. The exact function isn't confirmed by the name alone.
  • Known-good reading in the archive: diode mode to ground 0.306. No known-good voltage reading here, and no condition is recorded for that value, so treat it as a guide that varies with board state.
  • To check it: power the board off and measure diode mode from the rail to ground, then power up and measure the DC voltage on the rail.
  • A diode reading far below 0.306 usually points to a short or a low-impedance load on the rail; a reading far above it can mean an open trace or missing part. Confirm with a voltage measurement before suspecting any part.
PP3V3_S0_SSD_R0.307––
AI: what PP3V3_S0_SSD_R is and how to check it

PP3V3_S0_SSD_R is a 3.3 V rail feeding the SSD section, and the S0 in its name indicates it belongs to the running (S0) state. Its known-good diode reading to ground is 0.307, with the board unpowered. Check it in diode mode from the rail to ground first, then power the board and confirm about 3.3 V at the rail. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far below 0.307 usually points to a short or a failing load on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0GPU0.492––
AI: what PP3V3_S0GPU is and how to check it

PP3V3_S0GPU is a 3.3 V rail for the GPU, and the S0 in its name indicates it comes up in the running (S0) state. The only known-good reading in the archive is a diode value of 0.492 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.492 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board.

PP3V3_S0GPU_MISC0.530––
AI: what PP3V3_S0GPU_MISC is and how to check it
  • What it is: PP3V3_S0GPU_MISC is a 3.3 V rail, read from the name: PP = power rail, 3V3 = 3.3 volts, S0 = running state, GPU_MISC = a miscellaneous GPU-side supply. It's a general reading of the name, not from this board's data.
  • Known-good: diode 0.530 in diode mode (no stated condition). No known-good voltage or resistance reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the DC voltage, which should sit near 3.3 V.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or a heavy load on the rail, but one reading doesn't confirm a bad part — compare against a known-good board before replacing anything.
PP5V_S00.390.399–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail for the S0 (running) state, as the name indicates. The archive lists a known-good diode reading of 0.39 to ground and a voltage of 0.399; the voltage figure looks like a diode-style reading rather than a powered rail voltage, so treat it as a guide and confirm the condition it was taken under. Check it unpowered in diode mode from PP5V_S0 to ground, then power the board and measure the voltage at the rail. No powered voltage known-good value is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.39 usually suggests a short or leaky load on the rail; a far higher one can mean an open path.

PP5V_S0_AUDIO_AMP_L0.399––
AI: what PP5V_S0_AUDIO_AMP_L is and how to check it

PP5V_S0_AUDIO_AMP_L is the 5 V audio amplifier rail; the name indicates it is a 5 V supply that comes up in the S0 (running) state. The only known-good reading in the archive is a diode reading of 0.399 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure the voltage, which should be about 5 V once the board is in S0. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below 0.399 suggests a short or leaky load on the rail; far above it suggests an open path, but one reading alone doesn't confirm a bad part.

PP5V_S0_AUDIO_AMP_R0.400––
AI: what PP5V_S0_AUDIO_AMP_R is and how to check it

PP5V_S0_AUDIO_AMP_R — from the name, a 5 V rail feeding the audio amplifier, enabled in the S0 (running) state. So it should only come up once the board is fully on, not in standby.

  • Known-good: diode 0.400 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage, ideally with audio playing.
  • A diode reading well below 0.400 suggests a short or leaky load on the rail; a missing or low voltage with a good diode reading points upstream, at the enable or the 5 V source feeding it.
  • These are community readings and vary with board state, so treat them as a guide, not a pass/fail limit.
PP5V_S0_CPUIMVP_VCC0.408––
AI: what PP5V_S0_CPUIMVP_VCC is and how to check it
  • What it is: From the name, PP5V_S0_CPUIMVP_VCC is a 5 V rail that is present in S0 (running) state and feeds the CPU IMVP supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.408 to ground (no condition given). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.408. Then power up and measure the DC voltage; expect about 5 V, though that figure is general, not from this board's data.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open feed. A missing voltage in S0 points to the enable or upstream supply for this rail.
PP5V_S0_CPUVCCIOS0_VCC0.400––
AI: what PP5V_S0_CPUVCCIOS0_VCC is and how to check it
  • What it is: A 5 V rail, from the name. The S0 part says it belongs to the running state, and CPUVCCIOS0 suggests it feeds the CPU's S0 I/O supply. That's from the name only; the parts on the net aren't known.
  • Known-good reading: diode 0.400 in the archive, no condition recorded. There is no known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.400. Then power up and measure the voltage, comparing with a known-good board since no voltage value is listed.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, and a missing voltage points to the supply feeding it. A small difference can be normal, so confirm before replacing anything.
PP5V_S0_GFXIMVP_VDD0.39––
AI: what PP5V_S0_GFXIMVP_VDD is and how to check it

PP5V_S0_GFXIMVP_VDD — 820-3332

  • From the name: a 5 V rail (PP5V), active in S0 (running state), feeding the GFXIMVP graphics power section's VDD. The name is the only source for that; the parts on the net aren't documented here.
  • Known-good reading: diode 0.39 in diode mode to ground, board unpowered. That's a community guide, not a factory spec; no known-good voltage reading is recorded here.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 0.39. Then power up and measure the DC voltage at the rail.
  • A diode reading far below 0.39 suggests a short or a leaky load on the rail; far above suggests an open path. Confirm with the powered voltage before replacing anything — one reading alone doesn't condemn a part.
PP5V_S0_P1V5_LDO_BIAS0.492––
AI: what PP5V_S0_P1V5_LDO_BIAS is and how to check it

PP5V_S0_P1V5_LDO_BIAS (820-3332)

  • From the name, this is a 5 V rail that is present in the S0 (running) state and feeds the 1.5 V LDO bias supply. It is a bias rail, so it is expected to be up whenever the board is in S0.
  • Known-good reading from the archive: diode mode to ground 0.492. No known-good voltage reading is recorded here.
  • To check it: power off and measure diode mode from the rail to ground, then power the board into S0 and measure the voltage at the rail. Compare the diode reading with 0.492.
  • A diode reading far below 0.492 usually points to a short or a leaky load on the rail; far above it suggests an open path. Confirm with the voltage measurement before suspecting any part.
PP5V_S0_PCH_V5REF0.377––
AI: what PP5V_S0_PCH_V5REF is and how to check it

PP5V_S0_PCH_V5REF is a 5 V rail that, from its name, belongs to the S0 (running) state and feeds the PCH's V5REF reference input. The only known-good reading here is a diode value of 0.377 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered: diode mode from the rail to ground, red probe on ground, and compare with 0.377. A much lower reading suggests a short or a leaky part on the rail; a much higher one can mean an open trace or missing connection.
  • Then power the board and measure the voltage at the rail in the S0 state. No known-good voltage is listed, so compare against a matching rail on a known-good board rather than a fixed number.
  • A rail that stays absent in S0 usually points upstream, to its enable or its source supply, rather than to the rail itself.
PP5V_S0_PCHVCCIOS0_VCC0.398––
AI: what PP5V_S0_PCHVCCIOS0_VCC is and how to check it
  • What it is: From the name, PP5V_S0_PCHVCCIOS0_VCC is a 5 V rail feeding the PCH's VCCIO for the S0 (running) state on the 820-3332. The S0 prefix means it should be present once the board is fully powered on, not in standby.
  • Known-good reading: Diode mode to ground is 0.398 in the readings archive. That's a community value and a guide only; no known-good voltage reading is listed here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage at the rail, expecting about 5 V.
  • If it's far off: A diode reading well below 0.398 suggests a short or leaky load on the rail; a much higher or open reading suggests a broken trace or missing source. Confirm with the voltage measurement before suspecting any part, since one reading alone isn't proof.
PP5V_S0_RMC_FLTOL––
AI: what PP5V_S0_RMC_FLT is and how to check it

PP5V_S0_RMC_FLT is a 5 V rail that, from its name, is a filtered (FLT) supply for the RMC section and is active in the S0 running state. The only known-good reading here is a diode reading of OL to ground, so there is no known-good voltage value for this rail. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S0. A diode reading far below OL suggests a short or leaky load on the rail, but a single reading doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PP5V_S0_VCCSAS0_VCC0.399––
AI: what PP5V_S0_VCCSAS0_VCC is and how to check it

PP5V_S0_VCCSAS0_VCC is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds the SAS-related supply domain. The archive lists one known-good diode reading of 0.399, with no condition noted and no known-good voltage reading here.

  • Check it unpowered: diode mode, black probe to ground, red to the rail. A far lower reading than 0.399 suggests a short or leaky part on the rail; a far higher one suggests an open path.
  • Then power the board and measure the voltage; there is no known-good voltage in this data, so compare against the 5 V the name implies and against a matching rail on a known-good board.
  • A rail that is missing under power but reads normally in diode mode usually points to an enable or upstream supply problem rather than a shorted load.
PP5V_S0GPU_P1V05_GPU0.400––
AI: what PP5V_S0GPU_P1V05_GPU is and how to check it

PP5V_S0GPU_P1V05_GPU is a 5 V rail that feeds the GPU's 1.05 V supply, going by the name; the S0 in it means it belongs to the running state. The archive lists one known-good diode reading of 0.400 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.400 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S0GPU_P1V35_GPU0.402––
AI: what PP5V_S0GPU_P1V35_GPU is and how to check it

PP5V_S0GPU_P1V35_GPU — reference note

  • From its name, this is a 5 V supply (PP5V) that is switched on in the S0 running state and feeds the GPU section, with a 1.35 V GPU rail named alongside it. The name alone doesn't confirm which parts sit on the net.
  • Known-good reading in the archive: diode 0.402 in diode mode (no condition recorded). There is no known-good voltage or resistance reading here.
  • To check it: power off and unplug, then measure diode mode from the net to ground and compare with 0.402. Then power up and measure the voltage — the data gives no expected value, so compare against a matching rail on a known-good board.
  • A diode reading far below 0.402 usually points to a short or a failing load on the rail; far above it can mean an open path. Confirm with a second measurement before replacing anything.
PPBUS_S0_LCDBKLT_FUSED0.445––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it
  • What it is: From the name, PPBUS_S0_LCDBKLT_FUSED is the fused backlight supply rail for the LCD, active in the S0 (running) state. It's the output side of the backlight fuse, feeding the display backlight circuit.
  • Known-good reading: Diode mode to ground is 0.445 (community archive value, a guide only). No known-good voltage reading is available here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.445. Then apply power and measure the voltage on the rail while the board is in S0.
  • If far off: A much lower diode reading suggests a short on the rail or its load; a much higher one suggests an open fuse or broken path. Confirm with a voltage check before replacing anything.
PPBUS_S0_LCDBKLT_PWR_SW0.906––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
  • What it is: From the name, PPBUS_S0_LCDBKLT_PWR_SW is the switched backlight power rail, active in the S0 (running) state. The data doesn't show which parts sit on it.
  • Known-good reading: diode 0.906 in the archive (community value, condition not stated). No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far from known-good: a low diode reading usually points to a short or leaky part on the rail, but one reading isn't proof. Compare with a matching rail or a known-good board before replacing anything.
PPCPUVCCIO_S0_REG_R0.011–12.500R
AI: what PPCPUVCCIO_S0_REG_R is and how to check it

PPCPUVCCIO_S0_REG_R — reference note

  • What it is: From the name, a regulated CPU/VCCIO supply rail active in the S0 (running) state. The exact parts on the net aren't documented here.
  • Known-good readings (community guide): diode 0.011, resistance 12.500R. These are very low, so treat them as a guide only and compare against a matching rail or a known-good board.
  • How to check: Power off and unplug, then measure diode mode to ground on the rail; then apply power and measure the rail voltage. No known-good voltage reading is recorded here.
  • If far from known-good: a much lower diode or resistance reading usually points to a short or a failing load on the rail; a much higher one to an open trace or missing feed. Confirm with a second measurement before replacing anything.
PPPCHVCCIO_S0_REG_R0.040––
AI: what PPPCHVCCIO_S0_REG_R is and how to check it

PPPCHVCCIO_S0_REG_R — the name suggests a regulated I/O supply rail active in S0 (running). That's from the name only; the parts it feeds aren't known.

  • Known-good: diode 0.040 to ground. No known-good voltage reading here.
  • Check: board unpowered, diode mode from the net to ground; then power up and measure the voltage.
  • A diode far from 0.040 usually points to a short or a leaky load on the rail, but one reading isn't proof — compare with a matching rail before condemning anything.
PPVCCSA_S0_REG0.008––
AI: what PPVCCSA_S0_REG is and how to check it

PPVCCSA_S0_REG — the name indicates a supply rail (PP = power rail) for VCCSA, enabled in the S0 (running) state. It is a regulated rail, so it should be present only when the board is powered on and out of reset.

  • Known-good reading: diode-to-ground 0.008 (from the readings archive; a guide only, and it varies with board state). No known-good voltage reading here.
  • Check it: with the board unpowered, measure diode mode from the rail to ground and compare with 0.008. Then power up and measure the DC voltage on the rail.
  • If it's far off: a diode reading much lower than 0.008 suggests a short or a failing load on the rail; a correct diode reading but no voltage points to the rail's regulator or its enable, not the load. Confirm with the voltage measurement before replacing anything.
PPVCCSA_S0_REG_R0.008–8.800R
AI: what PPVCCSA_S0_REG_R is and how to check it

PPVCCSA_S0_REG_R is a running-state (S0, from the name) regulated supply rail; "VCCSA" usually means the system-agent supply, but that's general naming, not from this board's data. Known-good here: diode 0.008 and resistance 8.800R. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading here, so compare against a matching rail or a known-good board. A reading far from 0.008 diode or 8.800R usually points to a short or a failed part on the rail, but one reading alone doesn't confirm a bad part.

PPVCORE_S0_AXG0.002––
AI: what PPVCORE_S0_AXG is and how to check it

PPVCORE_S0_AXG is the CPU core power rail; the "S0" in the name indicates it is active in the running (S0) state, and "VCORE" indicates core voltage. The only known-good reading in the archive is a diode value of 0.002, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far above 0.002 usually points to an open or high-resistance path rather than a short, but a single reading doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPVCORE_S0_AXG1_L0.002–2.000R
AI: what PPVCORE_S0_AXG1_L is and how to check it

PPVCORE_S0_AXG1_L — reference note

  • What it is: From the name, this is the VCORE (CPU core supply) rail, in the S0 (running) state. The "AXG1" suffix is a rail identifier; the exact part it feeds isn't known from the readings archive.
  • Known-good readings (guide, from community data): diode 0.002 and resistance 2.000R. These are very low values, which is normal for a high-current core rail — it is not a short by itself.
  • How to check: Power off and unplug, then measure diode mode and resistance from the rail to ground. With power applied, measure the voltage on the rail and compare it with the S0 state.
  • No known-good voltage is recorded here, so compare against a known-good board or a matching rail on the other side of a pair.
  • If a reading is far from known-good: a much higher diode/resistance suggests an open trace or missing feed; a much lower one suggests a shorted load. Confirm with a second measurement before suspecting a part.
PPVCORE_S0_AXG2_L0.002–2.000R
AI: what PPVCORE_S0_AXG2_L is and how to check it
  • What it is: PPVCORE_S0_AXG2_L is a processor core power rail; the "S0" in the name indicates it is up in the running state, and "VCORE" indicates core voltage. This is inferred from the name only.
  • Known-good readings: diode 0.002 and resistance 2.000R, both from the readings archive. These are very low values, which is normal for a high-current core rail. Treat them as a guide, since community readings vary with board state.
  • How to check it: with the board powered off, measure diode mode and then resistance from the rail to ground. Then apply power and measure the voltage on the rail.
  • No known-good voltage reading here. Compare the voltage against a known-good board or the rail's expected value from the schematic.
  • If a reading is far off: a much higher diode or resistance reading points to an open or missing connection; a near-zero reading in both directions can be normal on this rail, so confirm against a known-good board before suspecting a short.
PPVCORE_S0_CPU0.001––
PPVCORE_S0_CPU_PH10.001–2.000R
AI: what PPVCORE_S0_CPU_PH1 is and how to check it

PPVCORE_S0_CPU_PH1 is the CPU core power rail (VCORE) at the S0 running state, judging from the name; it's a high-current rail, so low readings to ground are expected. In the readings archive it shows diode 0.001 and resistance 2.000R — treat these as a guide only, since community readings vary with board state. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from these usually points to a short or a failed phase on the rail, but a small difference can be normal, so confirm before replacing anything. No known-good voltage reading is available here.

PPVCORE_S0_CPU_PH20.001–2.000R
AI: what PPVCORE_S0_CPU_PH2 is and how to check it

PPVCORE_S0_CPU_PH2 — from the name, this is a CPU core power rail (VCORE) in the S0 (running) state; the PH2 suffix suggests a phase of a multiphase CPU supply. The archive lists a diode reading of 0.001 and a resistance of 2.000R for this net, so treat those as a guide only, since readings vary with board state. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from the known-good diode or resistance values usually points to a short or a heavy load on the core rail rather than a fault elsewhere. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PPVCORE_S0_CPU_PH30.001–2.000R
AI: what PPVCORE_S0_CPU_PH3 is and how to check it
  • What it is: From the name, PPVCORE_S0_CPU_PH3 is a CPU core power rail (VCORE) in the S0 (running) state, phase 3 of a multi-phase supply. The data doesn't list which parts sit on it.
  • Known-good readings: diode 0.001 and resistance 2.000R, from the readings archive. Treat these as a guide only; no voltage reading is recorded here.
  • How to check: Power off and unplug, then measure diode mode to ground and resistance on the rail. Then power up and measure the voltage on the rail.
  • If it's far off: a near-short diode or very low resistance usually points to a shorted load or a failed phase component, but one reading isn't proof. Compare against a matching phase or a known-good board before replacing anything.
PPVCORE_S0_GFX_PH10.030–35.000R
AI: what PPVCORE_S0_GFX_PH1 is and how to check it

PPVCORE_S0_GFX_PH1 — reference note

  • What it is: from the name, a processor core power rail (VCORE) for the graphics section, in the S0 running state; PH1 suggests one phase of a multi-phase supply. Which parts sit on the net isn't known here.
  • Known-good readings (community archive, guide only): diode 0.030 and resistance 35.000R. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground, then resistance to ground; then power up and measure the rail voltage.
  • If far from known-good: a much lower diode or resistance reading usually points to a short or a failing load on the rail; a much higher one can mean an open path. Confirm with a second measurement before replacing anything.
PPVCORE_S0_GFX_PH20.030–35.000R
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 is a graphics core power rail; the S0 in the name indicates it belongs to the running state, and PH2 suggests a switching phase output. Known-good readings here are diode 0.030 and resistance 35.000R, both taken with the board unpowered. Check it in diode mode to ground first, then measure the voltage with power applied; no known-good voltage reading is recorded here. A reading far from those values usually points to a short or a faulty component on the rail, but a small difference can be normal, so compare against a matching rail before condemning anything.

PPVIN_S0_GFXIMVP_R0.45––
AI: what PPVIN_S0_GFXIMVP_R is and how to check it
  • What it is: From its name, PPVIN_S0_GFXIMVP_R is the input supply rail for the GFX IMVP regulator, active in the S0 (running) state. The board data only gives the net name and stage, not which parts sit on it.
  • Known-good reading: diode 0.45 (community archive value, a guide only; no condition given). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far from 0.45: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. Confirm with voltage under power before replacing anything.
PPVOUT_S0_LCDBKLT1.2255.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the name indicates a switched S0 (running-state) supply, and "VOUT" and "BKLT" point to a boost converter output feeding the display backlight. Known-good readings here are a diode of 1.22 and a voltage of 55.000, both from the readings archive and only a guide, since they vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode far below 1.22 suggests a short or leaky load on the rail; a voltage far from 55.000 with a normal diode points to the backlight boost circuit or its enable not running. No known-good resistance reading is recorded for this rail.

PPVOUT_S0_PCH_DCPSST0.531––
AI: what PPVOUT_S0_PCH_DCPSST is and how to check it

PPVOUT_S0_PCH_DCPSST is a running-state (S0, from the name) supply rail for the PCH, likely a DC/DC-converted output; the exact source isn't known here. The only known-good reading in the archive is a diode value of 0.531 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far below 0.531 usually suggests a short or leaky load on the rail, but one reading alone doesn't confirm a bad part.

Every net with a reading

NetDiodeVoltageResistance
1V0_GPU_IOUTOL––
1V5_S0_FB0.776––
1V05_S0_RMC_DIVOL––
1V5_S0_SW0.376––
4V5_NR0.658––
4V5_REG_EN0.711––
4V5_REG_IN0.427––
ADAPTER_SENSE0.63––
ALL_SYS_PWRGD0.465––
ALL_SYS_PWRGD_ROL––
AP_CLKREQ_L0.463––
AP_CLKREQ_Q_L0.470––
AP_PWR_EN0.460––
AP_RESET_CONN_L0.471––
AP_RESET_L0.434––
AUD_CONN_HP_LEFT0.782––
AUD_CONN_HP_RIGHT0.745––
AUD_CONN_MIC0.538––
AUD_CONN_MIC_XW0.391––
AUD_CONN_SLEEVE0.528––
AUD_CONN_SLEEVE_XW0.390––
AUD_CONN_TIPDET_INVOL––
AUD_CONN_TYPEDETOL––
AUD_DMIC_CLK0.705––
AUD_DMIC_CLK_R0.702––
AUD_DMIC_SDA10.740––
AUD_DMIC_SDA20.703––
AUD_GPIO_30.520––
AUD_HP_PORT_L0.765––
AUD_HP_PORT_R0.765––
AUD_HP_PORT_REF0.454––
AUD_HP_ZOBEL_L0.042––
AUD_HP_ZOBEL_R0.041––
AUD_I2C_INT_L0.529––
AUD_IP_PERIPHERAL_DET0.429––
AUD_IPHS_SWITCH_EN0.565––
AUD_IPHS_SWITCH_EN_PCH0.572––
AUD_LO1_L_N0.704––
AUD_LO1_L_P0.707––
AUD_LO1_R_N0.705––
AUD_LO1_R_P0.705––
AUD_LO2_L_N0.700––
AUD_LO2_L_POL––
AUD_LO2_R_N0.703––
AUD_LO2_R_P0.709––
AUD_MIC_INL_N0.750––
AUD_MIC_INL_P0.740––
AUD_OUTJACK_INSERT_L0.445––
AUD_PORTA_DET_L0.822––
AUD_PORTB_DET_L0.690––
AUD_PORTC_DET_L0.420––
AUD_SDI_R0.466––
AUD_SENSE_A0.753––
AUD_SPDIF_OUT0.702––
AUD_SPDIF_OUT_JACK0.737––
AUD_SPKRAMP_SHUTDOWN_L0.520––
AUD_TIPDET_FET10.429––
AUD_TIPDET_FET20.660––
AUD_TIPDET_INVOL––
AUD_TYPEDETOL––
AUD_TYPEDET_ODOL––
AUD_TYPEDET_OD_INV0.470––
AUDIO_SCL0.475––
AUDIO_SDA0.479––
BKL_FB0.713––
BKL_FET_CNTL0.514––
BKL_FLT0.575––
BKL_FSET0.574––
BKL_ISEN10.637––
BKL_ISEN20.636––
BKL_ISEN30.636––
BKL_ISEN40.364––
BKL_ISEN50.634––
BKL_ISEN60.634––
BKL_ISET0.574––
BKL_SCL0.545––
BKL_SDA0.547––
BKL_SGND0.001––
BKL_SW0.432––
BKL_VSYNC_R0.575––
BKLT_EN0.576––
BKLT_PLT_RST_L0.437––
BLC_GPIO0.576––
BLC_I2C_MUX_SEL0.592––
BTMUX_SEL0.517––
BUTTON_DISABLE0.450––
CAP_COMP_HOL––
CAP_COMP_LOL––
CAP_COMP_L_INVOL––
CAP_SINKOL––
CAP_SOURCEOL––
CAP_VREF_HOL––
CAP_VREF_LOL––
CH_HS_MIC0.529––
CHGR_ACIN0.54––
CHGR_AGATE0.66––
CHGR_AGATE_DIVOL––
CHGR_AMON0.73––
CHGR_BGATE0.68––
CHGR_BMON0.73––
CHGR_BOOT0.60––
CHGR_CELL0.72––
CHGR_CSI_N0.66–22.500R
CHGR_CSI_P0.64–22.500R
CHGR_CSI_R_N0.642––
CHGR_CSI_R_P0.642––
CHGR_CSO_N0.45–4.900R
CHGR_CSO_P0.45–4.900R
CHGR_CSO_R_N0.450––
CHGR_CSO_R_P0.450––
CHGR_DCIN0.60––
CHGR_DCIN_D_R0.60120.100–
CHGR_ICOMP0.73––
CHGR_ICOMP_RC0.731––
CHGR_LGATE0.46––
CHGR_PHASE0.45––
CHGR_RST_L0.50––
CHGR_SGATE0.654––
CHGR_SGATE_DIVOL––
CHGR_UGATE0.90––
CHGR_VCOMP0.73––
CHGR_VCOMP_ROL––
CHGR_VFRQ0.52––
CHGR_VNEG0.54––
CHGR_VNEG_ROL––
CHS_CLAMPO0.486––
COMP_CPU_VCORE_RMCOL––
CON_DMIC_CLK0.711––
CON_DMIC_PWR0.310––
CON_DMIC_SDA10.711––
CON_DMIC_SDA20.713––
CPU_AXG_SENSE_N0.001––
CPU_AXG_SENSE_P0.005––
CPU_AXG_SENSE_R0.012––
CPU_CATERR_L0.386––
CPU_CFG<0>0.387––
CPU_CFG<1>0.385––
CPU_CFG<2>0.385––
CPU_CFG<3>0.382––
CPU_CFG<4>0.371––
CPU_CFG<5>0.361––
CPU_CFG<6>0.371––
CPU_CFG<7>0.381––
CPU_CFG<8>0.377––
CPU_CFG<9>0.400––
CPU_CFG<10>0.380––
CPU_CFG<11>0.376––
CPU_CFG<12>0.383––
CPU_CFG<13>0.381––
CPU_CFG<14>0.379––
CPU_CFG<15>0.378––
CPU_CFG<16>0.381––
CPU_CFG<17>0.383––
CPU_DDR_VREF0.447––
CPU_EDP_COMP0.037––
CPU_MEM_RESET_L0.339––
CPU_PECI0.377––
CPU_PECI_R0.332––
CPU_PEG_COMP0.036––
CPU_PROC_SEL_L0.003––
CPU_PROCHOT_L0.082––
CPU_PROCHOT_R_L0.138––
CPU_PWRGD0.476––
CPU_SM_RCOMP<0>0.139––
CPU_SM_RCOMP<1>0.027––
CPU_SM_RCOMP<2>0.192––
CPU_THRMTRIP_3V30.751––
CPU_VCCIO_SEL0.001––
CPU_VCCIOSENSE_N0.002––
CPU_VCCIOSENSE_P0.013––
CPU_VCCSA_VID<1>0.382––
CPU_VCCSASENSE0.008––
CPU_VCCSASENSE_DIV0.517––
CPU_VCCSENSE_P0.002––
CPU_VCCSENSE_R0.011––
CPU_VCORE_RMC_DIVOL––
CPU_VCORE_RMCNOL––
CPU_VCORE_RMCPOL––
CPU_VIDALERT_L0.089––
CPU_VIDALERT_L_R0.133––
CPU_VIDSCLK0.069––
CPU_VIDSCLK_R0.067––
CPU_VIDSOUT0.077––
CPU_VIDSOUT_R0.078––
CPUIMVP_AXG_PGOOD0.604––
CPUIMVP_AXG_PWM20.578––
CPUIMVP_BOOT10.618––
CPUIMVP_BOOT1_RC0.619––
CPUIMVP_BOOT1G0.618––
CPUIMVP_BOOT1G_R0.618––
CPUIMVP_BOOT20.618––
CPUIMVP_BOOT2_RC0.617––
CPUIMVP_BOOT2G0.600––
CPUIMVP_BOOT2G_RC0.600––
CPUIMVP_BOOT30.596––
CPUIMVP_BOOT3_RC0.609––
CPUIMVP_FBA0.685––
CPUIMVP_FBA_R0.013––
CPUIMVP_FBB0.687––
CPUIMVP_FBB_R0.013––
CPUIMVP_IMAXA0.625––
CPUIMVP_IMAXB0.600––
CPUIMVP_ISNS1_N0.001––
CPUIMVP_ISNS1_P0.001––
CPUIMVP_ISNS1G_N0.002––
CPUIMVP_ISNS1G_P0.002––
CPUIMVP_ISNS1G_R_NOL––
CPUIMVP_ISNS1G_R_POL––
CPUIMVP_ISNS2_N0.001––
CPUIMVP_ISNS2_P0.001––
CPUIMVP_ISNS2G_N0.002––
CPUIMVP_ISNS2G_P0.002––
CPUIMVP_ISNS3_N0.001––
CPUIMVP_ISNS3_P0.001––
CPUIMVP_ISUM0.103––
CPUIMVP_ISUM_R0.104––
CPUIMVP_ISUM_R_POL––
CPUIMVP_ISUM2P0.049––
CPUIMVP_ISUM3P0.026––
CPUIMVP_ISUMG_AVE_RP0.104––
CPUIMVP_ISUMG_AVEP0.104––
CPUIMVP_ISUMG_IOUTOL––
CPUIMVP_ISUMG_R_NOL––
CPUIMVP_ISUMG_R_POL––
CPUIMVP_ISUMG1P0.052––
CPUIMVP_ISUMG2P0.050––
CPUIMVP_ISUMGN0.008––
CPUIMVP_ISUMN0.005––
CPUIMVP_LGATE10.511––
CPUIMVP_LGATE2G0.522––
CPUIMVP_LGATE30.520––
CPUIMVP_NTC0.604––
CPUIMVP_NTCG0.696––
CPUIMVP_PGOOD0.585––
CPUIMVP_PH2_SNUBOL––
CPUIMVP_PHASE10.001–2.000R
CPUIMVP_PHASE1G0.002–2.000R
CPUIMVP_PHASE20.001–2.000R
CPUIMVP_PHASE2G0.002–2.000R
CPUIMVP_PHASE30.002––
CPUIMVP_PHASE3_L0.001–2.000R
CPUIMVP_PWM30.581––
CPUIMVP_SKIP0.619––
CPUIMVP_SLEW0.702––
CPUIMVP_TONA0.684––
CPUIMVP_TONB0.682––
CPUIMVP_UGATE1G0.693––
CPUIMVP_UGATE20.695––
CPUIMVP_UGATE2G0.697––
CPUIMVP_UGATE30.696––
CPUIMVP_VR_ON0.466––
CPUTHMSNS_ALERT_L0.770––
CPUTHMSNS_D2_N0.768––
CPUTHMSNS_D2_P0.767––
CPUTHMSNS_THM_L0.777––
CPUVCCIOISNS_R_NOL––
CPUVCCIOISNS_R_POL––
CPUVCCIOS0_AGND0.002––
CPUVCCIOS0_BOOT_RC0.536––
CPUVCCIOS0_CS_N0.011––
CPUVCCIOS0_CS_P0.011––
CPUVCCIOS0_DRVH0.527––
CPUVCCIOS0_DRVL0.440––
CPUVCCIOS0_EN0.533––
CPUVCCIOS0_FB0.517––
CPUVCCIOS0_FSEL0.003––
CPUVCCIOS0_LL0.011–12.500R
CPUVCCIOS0_OCSET0.520––
CPUVCCIOS0_PGOOD0.500––
CPUVCCIOS0_RTN0.512––
CPUVCCIOS0_SREF0.530––
CPUVCCIOS0_VBST0.542––
CPUVCCIOS0_VO0.517––
CPUVSENSE_IN0.016––
CS4206_FLYC0.416––
CS4206_FLYN1.575––
CS4206_FLYP0.620––
CS4206_FN1.575––
CS4206_FP0.441––
CS4206_VCOM0.594––
CS4206_VREF_ADC0.759––
DAC_AVDD0.613––
DC_TEST_B3_C2OL––
DC_TEST_B63_A64OL––
DC_TEST_B65_C64OL––
DC_TEST_BG64_BH65OL––
DC_TEST_BH1_BG2OL––
DC_TEST_BH3_BJ2OL––
DC_TEST_BJ64_BH63OL––
DCIN_ISOL_GATE0.779––
DCIN_ISOL_GATE_ROL6.700–
DCIN_S5_VSENSEOL––
DCINVSENS_EN0.750––
DCINVSENS_EN_L0.466––
DDR3THMSNS_D1_N0.779––
DDR3THMSNS_D1_P0.785––
DDRREG_1V8_VREF0.639––
DDRREG_DRVH0.717––
DDRREG_DRVH_R0.718––
DDRREG_DRVL0.472––
DDRREG_EN0.561––
DDRREG_FB0.691––
DDRREG_LL0.227––
DDRREG_MODE0.546––
DDRREG_P1V35_LOL––
DDRREG_TRIP0.753––
DDRREG_VBST0.631––
DDRREG_VDDQSNS0.227––
DDRREG_VSW0.224––
DDRREG_VTTSNS0.165––
DMI_CLK100M_CPU_N0.392––
DMI_CLK100M_CPU_P0.390––
DP_A_AUXCH_DDC_N0.718––
DP_A_AUXCH_DDC_P0.717––
DP_A_CA_DET_BUF0.641––
DP_A_LSX_ML_N<1>0.714––
DP_AUXCH_ISOL0.709––
DP_AUXIO_EN0.617––
DP_B_AUXCH_DDC_N0.705––
DP_B_AUXCH_DDC_P0.725––
DP_B_CA_DET_BUF0.639––
DP_B_LSX_ML_P<1>0.740––
DP_DDC_MUX_CROSSBAR_L0.51––
DP_EXTA_CA_DET_EG0.633––
DP_EXTA_MUX_EN0.513.30–
DP_EXTA_MUX_SEL_EG0.51––
DP_EXTB_CA_DET_EG0.62––
DP_EXTB_MUX_EN0.51––
DP_EXTB_MUX_SEL_EG0.520––
DP_INT_AUX_C_N0.706––
DP_INT_AUX_C_P0.692––
DP_INT_AUX_NOL––
DP_INT_AUX_POL––
DP_INT_EG_AUX_N0.729––
DP_INT_EG_AUX_P0.726––
DP_INT_EG_HPD0.63––
DP_INT_EG_ML_N<0>0.405––
DP_INT_EG_ML_N<1>0.392––
DP_INT_EG_ML_N<2>0.393––
DP_INT_EG_ML_N<3>0.394––
DP_INT_EG_ML_P<0>0.410––
DP_INT_EG_ML_P<1>0.394––
DP_INT_EG_ML_P<2>0.394––
DP_INT_EG_ML_P<3>0.394––
DP_INT_IG_AUX_N0.335––
DP_INT_IG_AUX_P0.335––
DP_INT_IG_HPD0.643––
DP_INT_IG_ML_N<0>0.311––
DP_INT_IG_ML_N<1>0.326––
DP_INT_IG_ML_N<2>0.314––
DP_INT_IG_ML_N<3>0.318––
DP_INT_IG_ML_P<0>0.315––
DP_INT_IG_ML_P<1>0.314––
DP_INT_IG_ML_P<2>0.319––
DP_INT_IG_ML_P<3>0.318––
DP_INT_ML_C_N<0>0.419––
DP_INT_ML_C_N<1>0.414––
DP_INT_ML_C_P<0>0.414––
DP_INT_ML_C_P<1>0.414––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
DP_TBTPA_AUXCH_C_N0.542––
DP_TBTPA_AUXCH_C_P0.557––
DP_TBTPA_AUXCH_N0.735––
DP_TBTPA_AUXCH_P0.739––
DP_TBTPA_DDC_CLK0.625––
DP_TBTPA_DDC_DATA0.630––
DP_TBTPA_HPD0.565––
DP_TBTPA_HPD_BUF0.640––
DP_TBTPA_HPD_BUF_ENOL––
DP_TBTPA_ML_C_N<1>0.335––
DP_TBTPA_ML_C_P<1>0.333––
DP_TBTPA_ML_N<1>0.697––
DP_TBTPA_ML_P<1>0.707––
DP_TBTPB_AUXCH_N0.734––
DP_TBTPB_DDC_CLK0.633––
DP_TBTPB_DDC_DATA0.626––
DP_TBTPB_HPD_BUF0.640––
DP_TBTPB_ML_P<1>0.710––
DP_TBTSNK0_AUXCH_C_N0.584––
DP_TBTSNK0_AUXCH_C_P0.586––
DP_TBTSNK0_EG_AUXCH_N0.609––
DP_TBTSNK0_EG_AUXCH_P0.609––
DP_TBTSNK0_HPD0.543––
DP_TBTSNK0_HPD_EG0.62––
DP_TBTSNK0_HPD_IG0.63––
DP_TBTSNK0_ML_C_N<2>0.416––
DP_TBTSNK0_ML_C_N<3>0.419––
DP_TBTSNK0_ML_C_P<2>0.416––
DP_TBTSNK0_ML_C_P<3>0.420––
DP_TBTSNK1_AUXCH_C_N0.582––
DP_TBTSNK1_AUXCH_C_P0.579––
DP_TBTSNK1_EG_AUXCH_N0.639––
DP_TBTSNK1_EG_AUXCH_P0.612––
DP_TBTSNK1_HPD0.540––
DP_TBTSNK1_HPD_EG0.63––
DP_TBTSNK1_HPD_IG0.63––
DP_TBTSNK1_ML_C_P<1>0.412––
DP_TBTSRC_HPD0.562––
DPA_EG_DDC_CLK0.652––
DPA_EG_DDC_DATA0.653––
DPA_IG_AUX_CH_N0.402––
DPA_IG_AUX_CH_P0.406––
DPA_IG_DDC_CLK0.577––
DPA_IG_DDC_DATA0.584––
DPB_EG_DDC_CLK0.654––
DPB_EG_DDC_DATA0.654––
DPB_IG_AUX_CH_N0.408––
DPB_IG_AUX_CH_P0.409––
DPB_IG_DDC_CLK0.580––
DPB_IG_DDC_DATA0.585––
DPMUX_HPD_PD0.760––
DPMUX_LRESET_L0.52––
DPMUX_UC_CLK32K0.63––
DPMUX_UC_EXTAL0.61––
DPMUX_UC_IRQ0.548––
DPMUX_UC_MD10.61––
DPMUX_UC_MD20.58––
DPMUX_UC_NMI0.61––
DPMUX_UC_PECI0.61––
DPMUX_UC_PEVREF0.45––
DPMUX_UC_RESET_L0.61––
DPMUX_UC_RX0.59––
DPMUX_UC_TCK0.63––
DPMUX_UC_TDI0.63––
DPMUX_UC_TDO0.63––
DPMUX_UC_TMS0.63––
DPMUX_UC_TRST_L0.63––
DPMUX_UC_TX0.59––
DPMUX_UC_UNUSED0.49––
DPMUX_UC_VCL0.46––
DPMUX_UC_XTAL0.61––
DPMUX_UC_XTAL_ROL––
EG_BKLT_EN0.628––
EG_LCD_PWR_EN0.62––
EG_RESET_L0.633.30–
ENET_CLKREQ_L0.556––
ENET_MEDIA_SENSE_RDIV0.446––
ENET_RESET_L0.435––
EXCARD_CLKREQ_L0.565––
FAN_LT_PWM1.148––
FAN_LT_TACHOL––
FAN_RT_PWM1.151––
FAN_RT_TACHOL––
FB_A0_MF0.122––
FB_A0_RESET_L0.408––
FB_A0_SEN0.122––
FB_A0_VREFC0.368––
FB_A0_VREFD0.336––
FB_A0_ZQ0.122––
FB_A1_MF0.123––
FB_A1_RESET_L0.408––
FB_A1_SEN0.122––
FB_A1_VREFC0.369––
FB_A1_VREFD0.344––
FB_A1_ZQ0.122––
FB_B0_DQ<0>0.385––
FB_B0_MF0.124––
FB_B0_SEN0.123––
FB_B0_VREFC0.368––
FB_B1_MF0.125––
FB_B1_RESET_L0.435––
FB_B1_SEN0.123––
FB_B1_VREFC0.371––
FB_B1_VREFD0.354––
FB_B1_ZQ0.123––
FB_CAL_PD_VDDQ0.209––
FB_CAL_PU_GND0.047––
FB_CAL_TERM_GND0.067––
FB_CLAMP0.526––
FB_CLAMP_TOGGLE_REQ_L0.60––
FB_SW_LEG0.255––
FB_VREF0.697––
FBA0_CK_MID0.570––
FBA1_CK_MID0.574––
FBB0_CK_MID0.570––
FBB1_CK_MID0.571––
FBVDD_ALTVO0.538––
FDI_INT0.363––
FW_PME_L0.645––
FW_PWR_EN_PCH0.605––
G3_POWERON_L0.748––
GFXIMVP_BOOT10.53––
GFXIMVP_BOOT1_R0.556––
GFXIMVP_BOOT20.558––
GFXIMVP_BOOT2_R0.557––
GFXIMVP_COMP0.52––
GFXIMVP_COMP_ROL––
GFXIMVP_DPSLP_EN0.53––
GFXIMVP_FB0.30––
GFXIMVP_FB_GND_ROL––
GFXIMVP_FB_SNS_R0.399––
GFXIMVP_FB20.52––
GFXIMVP_ISEN10.52––
GFXIMVP_ISEN20.52––
GFXIMVP_ISNS1_N0.030––
GFXIMVP_ISNS1_P0.030––
GFXIMVP_ISNS2_N0.030––
GFXIMVP_ISNS2_P0.030––
GFXIMVP_ISUMN0.035––
GFXIMVP_ISUMN_R0.49––
GFXIMVP_ISUMP0.42––
GFXIMVP_ISUMP_COL––
GFXIMVP_LGATE10.45––
GFXIMVP_LGATE20.43––
GFXIMVP_NTC0.52––
GFXIMVP_PHASE10.03–35.000R
GFXIMVP_PHASE20.03–35.000R
GFXIMVP_PSI_L0.52––
GFXIMVP_PSI_R_L0.550––
GFXIMVP_RBIAS0.52––
GFXIMVP_UGATE10.47––
GFXIMVP_UGATE20.46––
GFXIMVP_VID<0>0.52––
GFXIMVP_VID<1>0.52––
GFXIMVP_VID<2>0.52––
GFXIMVP_VID<3>0.52––
GFXIMVP_VID<4>0.52––
GFXIMVP_VID<5>0.52––
GFXIMVP_VID<6>0.52––
GFXIMVP_VR_TT_L0.48––
GFXIMVP_VSSP10.00––
GFXIMVP_VSSP20.00––
GFXIMVP_VW0.52––
GFXIMVP6_IMON0.45––
GND_GFXIMVP_AGND0.00––
GPU_ALT_VREF0.730––
GPU_BUFRSTN0.716––
GPU_FBA_DEBUG00.235––
GPU_FBA_DEBUG10.226––
GPU_FBB_DEBUG10.228––
GPU_FBGND_SENSE0.004––
GPU_FBVDDQ_SENSE0.167––
GPU_JTAG_TMS0.734––
GPU_MLS_STRAP00.718––
GPU_MLS_STRAP10.717––
GPU_MLS_STRAP20.716––
GPU_MLS_STRAP30.716––
GPU_MLS_STRAP40.718––
GPU_OSC_27M_SSIN0.733––
GPU_OSC_27M_XTAL_BUFFOUT_R0.735––
GPU_OSC_27M_XTALIN0.832––
GPU_OSC_27M_XTALOUT0.817––
GPU_PEX_TERMP0.829––
GPU_RESET_R_L0.633––
GPU_ROM_CS_L0.733––
GPU_ROM_CS_L_ROL––
GPU_ROM_SCLK_ROL––
GPU_ROM_SI0.733––
GPU_ROM_SI_ROL––
GPU_ROM_SO0.724––
GPU_ROM_SO_ROL––
GPU_ROM_WP_LOL––
GPU_SMB_CLK0.720––
GPU_SMB_DAT0.722––
GPU_SSC_SMB_CLK0.709––
GPU_SSC_SMB_DAT0.707––
GPU_TDIODE_N0.502––
GPU_TDIODE_P0.779––
GPU_TESTMODE0.831––
GPUFB_AGND0.007––
GPUFB_BOOT_RC0.582––
GPUFB_CS_N0.163––
GPUFB_CS_P0.163––
GPUFB_DRVH0.602––
GPUFB_DRVH_R0.602––
GPUFB_DRVL0.440––
GPUFB_FSEL0.536––
GPUFB_GPU_OCSET_R0.165––
GPUFB_GPU_VO_R0.166––
GPUFB_LL0.163–177.800R
GPUFB_OCSET0.532––
GPUFB_PGOOD0.52––
GPUFB_RTN_DIV0.518––
GPUFB_SENSE_DIV0.516––
GPUFB_SET_R0.533––
GPUFB_SET00.537––
GPUFB_SET10.534––
GPUFB_SREF0.534––
GPUFB_VBST0.580––
GPUFB_VO0.531––
GPUTHMSNS_ALERT_L0.760––
GPUTHMSNS_D_N0.763––
GPUTHMSNS_D_P0.762––
GPUTHMSNS_THM_L0.764––
GPUVCORE_EN0.523.30–
GPUVCORE_INVOL––
GPUVCORE_IOUTOL––
GPUVCORE_PGOOD0.51––
GPUVCORE_SENSE_N0.00––
GPUVCORE_SENSE_P0.03––
GPUVSENSE_IN0.031––
GYRO_CSOL––
HDA_BIT_CLK0.483––
HDA_BIT_CLK_R0.449––
HDA_RST_L0.481––
HDA_RST_R_L0.449––
HDA_SDIN00.446––
HDA_SDOUT0.482––
HDA_SDOUT_R0.448––
HDA_SYNC0.487––
HDA_SYNC_R0.449––
HDMI_EG_CLK_C_N0.412––
HDMI_EG_CLK_C_P0.410––
HDMI_EG_DATA_C_N<0>0.410––
HDMI_EG_DATA_C_N<1>0.419––
HDMI_EG_DATA_C_N<2>0.421––
HDMI_EG_DATA_C_P<0>0.414––
HDMI_EG_DATA_C_P<1>0.430––
HDMI_EG_DATA_C_P<2>0.421––
HDMI_EG_DDC_CLK1.057––
HDMI_EG_DDC_CLK_Q0.792––
HDMI_EG_DDC_DATA1.056––
HDMI_EG_DDC_DATA_Q0.792––
HDMI_EG_HPD0.63––
HDMI_HPD_BUF0.60––
HDMI_HPD_L0.689––
HS_COMPUTING_IOUT0.712––
HS_GPU_IOUT0.718––
HS_MIC_BIAS0.476––
HS_MIC_HI0.479––
HS_OTHER_IOUT0.717––
HS_RX_BP0.587––
HS_SW_DET0.572––
I2C_DPMUX_A_SCL0.60––
I2C_DPMUX_A_SDA0.607––
I2C_DPMUX_UC_SCL0.545––
I2C_DPMUX_UC_SDA0.548––
I2C_SMC_GYRO_SCL_ROL––
I2C_SMC_GYRO_SDA_ROL––
I2C_SMC_SMS_SCL_ROL––
I2C_SMC_SMS_SDA_ROL––
IFPD_RSET0.795––
IFPEF_RSET0.795––
ISENSE_CPUVCCIO_IOUTOL––
ISENSE_P1V5MEM_IOUT0.655––
ISENSE_SA_IOUT0.662––
ISNS_1V5_MEM_N0.224––
ISNS_1V5_MEM_P0.224––
ISNS_1V5_MEM_R_N0.800––
ISNS_1V5_MEM_R_P0.800––
ISNS_AIRPORT_IOUTOL––
ISNS_AIRPORT_R_NOL––
ISNS_AIRPORT_R_POL––
ISNS_CPU_DDR_IOUTOL––
ISNS_CPU_DDR_R_NOL––
ISNS_CPU_DDR_R_POL––
ISNS_HS_COMPUTING_N0.445––
ISNS_HS_COMPUTING_P0.445––
ISNS_HS_GPU_N0.445––
ISNS_HS_GPU_P0.445––
ISNS_HS_OTHER_N0.445––
ISNS_HS_OTHER_P0.445––
ISNS_PP1V0_S0GPU_R_NOL––
ISNS_PP1V0_S0GPU_R_POL––
ISNS_PP1V5_S0GPU_R_N0.792––
ISNS_PP1V5_S0GPU_R_P0.789––
ISNS_SSD_IOUT0.656––
ISNS_SSD_N0.307––
ISNS_SSD_P0.307––
ISNS_SSD_R_N0.793––
ISNS_SSD_R_P0.793––
ISNS_TBT_IOUT0.649––
ISNS_TBT_N0.046––
ISNS_TBT_P0.047––
ISNS_TBT_R_N0.747––
ISNS_TBT_R_P0.747––
ISOLATE_CPU_MEM_L0.597––
ITPCPU_CLK100M_NOL––
ITPCPU_CLK100M_POL––
ITPXDP_CLK100M_N0.399––
ITPXDP_CLK100M_P0.391––
JTAG_DPMUXUC_TRST_L0.567––
JTAG_GMUX_TMS0.579––
JTAG_ISP_TCK0.641––
JTAG_ISP_TDI0.606––
JTAG_ISP_TDO0.617––
JTAG_ISP_TMS0.610––
JTAG_TBT_TCK0.554––
JTAG_TBT_TDI0.642––
JTAG_TBT_TDO0.650––
JTAG_TBT_TMS0.642––
KBDLED_ANODE10.605––
KBDLED_ANODE20.607––
KBDLED_CAP10.591––
KBDLED_CAP20.592––
KBDLED_SW10.390––
KBDLED_SW20.390––
LCD_BKLT_EN0.633.30–
LCD_BKLT_PWM0.55––
LCD_DRV_IOUTOL––
LCD_FSS0.64––
LCD_HPD0.616––
LCD_HPD_CONN0.61––
LCD_MUX_EN0.640––
LCD_MUX_SEL0.63––
LCD_PWR_EN0.623.30–
LCDBKLT_DISABLE0.433––
LCDBKLT_EN_DIVOL––
LCDBKLT_EN_L0.670––
LCDBKLT_IOUTOL––
LED_RETURN_10.63––
LED_RETURN_20.63––
LED_RETURN_30.63––
LED_RETURN_40.63––
LED_RETURN_50.63––
LED_RETURN_60.63––
LPC_AD_R<1>0.539––
LPC_AD_R<2>0.539––
LPC_AD_R<3>0.540––
LPC_AD<0>0.54––
LPC_AD<1>0.554––
LPC_AD<2>0.554––
LPC_AD<3>0.54––
LPC_CLK33M_DPMUX_UC0.601––
LPC_CLK33M_DPMUX_UC_R0.602––
LPC_CLK33M_LPCPLUS0.676––
LPC_CLK33M_LPCPLUS_R0.653––
LPC_CLK33M_SMC0.660––
LPC_CLK33M_SMC_R0.644––
LPC_FRAME_L0.54––
LPC_FRAME_R_L0.537––
LPC_PWRDWN_L0.593––
LPC_SERIRQ0.622––
LPCPLUS_GPIO0.600––
LPCPLUS_RESET_L0.565––
LSUBIN_N0.580––
LSUBIN_P0.580––
LVDS_BKL_PWM_RC0.556––
LVDS_IG_BKL_ON0.564––
LVDS_IG_PANEL_PWR0.563––
MCP6514_NEG0.672––
MCP6514_OUT0.635––
MCP6514_POS0.675––
MEM_A_A<1>0.196––
MEM_A_A<11>0.200––
MEM_A_A<15>0.196––
MEM_A_BA<1>0.212––
MEM_A_BA<2>0.200––
MEM_A_CKE<0>0.202––
MEM_A_CLK_N<0>0.311––
MEM_A_CLK_P<0>0.322––
MEM_A_CLK0_TERM_R0.316––
MEM_A_RAS_L0.196––
MEM_A_ZQ<15>0.246––
MEM_B_A<5>0.199––
MEM_B_A<8>0.196––
MEM_B_A<12>0.196––
MEM_B_A<14>0.198––
MEM_B_BA<0>0.198––
MEM_B_CLK_N<0>0.309––
MEM_B_CLK_N<1>0.311––
MEM_B_CLK_P<0>0.309––
MEM_B_CLK_P<1>0.310––
MEM_B_CLK0_TERM_R0.309––
MEM_B_CLK1_TERM_R0.319––
MEM_B_DQS_N<0>0.330––
MEM_B_DQS_P<0>0.327––
MEM_B_ODT<1>0.196––
MEM_B_WE_L0.197––
MEM_RESET_L0.451––
MEM_VDD_SEL_1V5_L0.592––
MEMRESET_ISOL_LS5V_L0.699––
MEMVTT_EN0.415––
MEMVTT_EN_L0.430––
MLB_RAMCFG00.641––
MLB_RAMCFG10.644––
MLB_RAMCFG20.640––
MLB_RAMCFG30.525––
MULTI_STRAP_REF0.834––
ODD_PWR_EN_L0.559––
P1V5_DIV_VMONOL––
P1V05_GPU_AGND0.004––
P1V05_GPU_BOOT_RC0.592––
P1V05_GPU_CS_N0.133––
P1V05_GPU_CS_P0.133––
P1V05_GPU_DRVH0.582––
P1V05_GPU_DRVH_R0.579––
P1V05_GPU_DRVL0.445––
P1V05_GPU_FB0.512––
P1V05_GPU_FSEL0.537––
P1V05_GPU_LL0.137––
P1V05_GPU_LL_FET0.133––
P1V05_GPU_OCSET0.526––
P1V05_GPU_PEX_IOVDD_SNS_N0.002––
P1V05_GPU_PEX_IOVDD_SNS_P0.140––
P1V05_GPU_RTN0.513––
P1V05_GPU_SREF0.531––
P1V05_GPU_VBST0.589––
P1V05_GPU_VO0.525––
P1V05_GPU_VO_R0.139––
P1V5_S0_DIVOL––
P1V05_S0GPU_EN0.523.30–
P1V5_S0GPU_IOUT0.649––
P1V05_S0GPU_PGOOD0.52––
P1V05_S0GPU_REG_R0.133––
P1V05_VID_VMONOL––
P1V5CPU_EN0.434––
P1V5CPU_EN_L0.414––
P1V5S0_EN0.761––
P1V5S0_LDO_FB0.619––
P1V5S0_LDO_PGOOD0.714––
P1V5S0_LDO_SS0.648––
P1V5S0_PGOOD0.562––
P1V5S3RS0FET_GATE0.676––
P1V5S3RS0FET_GATE_R0.676––
P1V8GPU_EN0.633.30–
P1V8S0_EN0.755––
P1V8S0_FB0.773––
P1V8S0_PGOOD0.562––
P1V8S0_SW0.117–308.500R
P1V35GPUFB_EN0.52––
P3V3GPU_EN0.633.30–
P3V3GPU_EN_L0.578––
P3V3GPU_MISC_EN_L0.579––
P3V3GPU_MISC_SS1.584––
P3V3GPU_SS1.576––
P3V3S0_EN_L0.437––
P3V3S0_SSOL––
P3V3S3_EN0.519––
P3V3S3_EN_L0.438––
P3V3S3_S4OL––
P3V3S3_SSOL––
P3V3S4_EN_L0.436––
P3V3S5_COMP20.739––
P3V3S5_COMP2_ROL––
P3V3S5_CSN20.144––
P3V3S5_CSP21.117––
P3V3S5_CSP2_R0.144––
P3V3S5_DRVH0.706––
P3V3S5_DRVL0.546––
P3V3S5_EN0.534––
P3V3S5_LL0.142––
P3V3S5_RF0.585––
P3V3S5_SNUBROL––
P3V3S5_TG0.706––
P3V3S5_VBST0.565––
P3V3S5_VFB20.580––
P3V3S5_VFB2_R0.144––
P3V3SUS_EN_L0.440––
P3V3SUS_SSOL––
P3V3WLAN_SSOL––
P3V3WLAN_VMON0.470––
P3V42G3H_BOOST0.625––
P3V42G3H_FB0.717––
P3V42G3H_SW0.3303.400–
P5V_DIV_VMONOL––
P5V0S0_EN_L0.585––
P5V0S0_SSOL––
P5V1_BIAS0.332––
P5V1_FB0.719––
P5V1_SW0.332––
P5V1_VIN0.601––
P5V3V3_S4_EN0.451––
P5VCUMULUS_SSOL––
P5VP3V3_SKIPSEL0.483––
P5VP3V3_VREF20.483––
P5VP3V3_VREG30.567––
P5VS3_EN0.520––
P5VS3_EN_L0.440––
P5VS3_SSOL––
P5VS4_COMP10.739––
P5VS4_COMP1_ROL––
P5VS4_CSN10.421––
P5VS4_CSP11.393––
P5VS4_CSP1_R0.422––
P5VS4_DRVH0.971––
P5VS4_DRVL0.546––
P5VS4_EN0.451––
P5VS4_LL0.422––
P5VS4_PGOOD0.503––
P5VS4_SNUBROL––
P5VS4_TG0.973––
P5VS4_VBST0.632––
P5VS4_VFB10.579––
P5VS4_VFB1_R0.422––
P5VS4_VSW0.425––
P5VSUS_EN_L0.581––
P5VSUS_SSOL––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.483––
PBUSVSENS_EN_L_DIVOL––
PCA9557D_RESET_L0.530––
PCH_A20GATE0.702––
PCH_CLK14P3M_REFCLK0.514––
PCH_CLK33M_PCIIN0.679––
PCH_CLK33M_PCIOUT0.657––
PCH_CLK96M_DOT_N0.778––
PCH_CLK96M_DOT_P0.777––
PCH_CLK100M_SATA_N0.776––
PCH_CLK100M_SATA_POL––
PCH_CLKIN_GNDN10.778––
PCH_CLKIN_GNDP10.778––
PCH_CORE_IOUTOL––
PCH_DAC_IREF0.699––
PCH_DF_TVS0.413––
PCH_DMI_COMP0.091––
PCH_DMI2RBIAS0.668––
PCH_DSWVRMEN0.780––
PCH_INIT3V3_L0.570––
PCH_INTRUDER_L0.781––
PCH_INTVRMEN_L0.781––
PCH_LVDS_IBG0.770––
PCH_PECI0.661––
PCH_PROCPWRGD0.472––
PCH_RCIN_L0.777––
PCH_RI_L0.654––
PCH_SATA3COMP0.091––
PCH_SATA3RBIAS0.670––
PCH_SATAICOMP0.077––
PCH_SATALED_L0.651––
PCH_SPKR0.701––
PCH_SRTCRST_L0.778––
PCH_STRP_TOPBLK_SWP_L0.555––
PCH_SUSACK_L0.596––
PCH_SUSWARN_L0.596––
PCH_USB_RBIAS0.024––
PCH_VCCIOSENSE_N0.002––
PCH_VCCIOSENSE_P0.042––
PCH_XCLK_RCOMP0.133––
PCHVCCIOS0_AGND0.001––
PCHVCCIOS0_BOOT_RC0.551––
PCHVCCIOS0_CS_N0.040––
PCHVCCIOS0_CS_P0.040––
PCHVCCIOS0_DRVH0.506––
PCHVCCIOS0_DRVL0.435––
PCHVCCIOS0_EN0.528––
PCHVCCIOS0_FB0.508––
PCHVCCIOS0_FSEL0.001––
PCHVCCIOS0_LL0.040––
PCHVCCIOS0_OCSET0.518––
PCHVCCIOS0_PGOOD0.496––
PCHVCCIOS0_RTN0.508––
PCHVCCIOS0_SREF0.526––
PCHVCCIOS0_VBST0.550––
PCHVCCIOS0_VO0.514––
PCI_INTA_L0.576––
PCI_INTB_L0.582––
PCI_INTC_L0.579––
PCI_INTD_L0.580––
PCIE_AP_D2R_PI_N0.369––
PCIE_AP_D2R_PI_P0.370––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_CONN_N0.388––
PCIE_CLK100M_AP_CONN_P0.389––
PCIE_CLK100M_AP_N0.388––
PCIE_CLK100M_AP_P0.389––
PCIE_CLK100M_ENET_N0.390––
PCIE_CLK100M_ENET_P0.388––
PCIE_CLK100M_PCH_N0.774––
PCIE_CLK100M_PCH_P0.776––
PCIE_CLK100M_SSD_N0.389––
PCIE_CLK100M_SSD_P0.386––
PCIE_CLK100M_TBT_N0.391––
PCIE_CLK100M_TBT_P0.390––
PCIE_ENET_D2R_N0.372––
PCIE_ENET_D2R_P0.370––
PCIE_ENET_R2D_C_N0.355––
PCIE_ENET_R2D_C_P0.354––
PCIE_SSD_D2R_C_N<1>0.325––
PCIE_SSD_D2R_C_P<1>0.322––
PCIE_SSD_D2R_MUX_OUT_N0.324––
PCIE_SSD_D2R_MUX_OUT_P0.321––
PCIE_SSD_D2R_N<0>0.323––
PCIE_SSD_D2R_N<1>0.324––
PCIE_SSD_D2R_P<0>0.320––
PCIE_SSD_R2D_C_N<0>0.319––
PCIE_SSD_R2D_C_N<1>0.318––
PCIE_SSD_R2D_C_P<0>0.322––
PCIE_SSD_R2D_C_P<1>0.322––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_TBT_D2R_N<1>0.325––
PCIE_TBT_D2R_N<2>0.327––
PCIE_TBT_D2R_P<2>0.324––
PCIE_TBT_R2D_C_N<0>0.318––
PCIE_TBT_R2D_C_N<1>0.319––
PCIE_TBT_R2D_C_P<1>0.320––
PCIE_WAKE_L0.630––
PDCINVSENS_EN_L_DIVOL––
PEG_CLK100M_N0.387––
PEG_CLK100M_P0.387––
PEG_CLKREQ_L0.52––
PEG_D2R_C_P<5>0.350––
PEG_D2R_N<3>0.320––
PEG_D2R_P<2>0.319––
PEG_D2R_P<3>0.317––
PEG_R2D_C_N<1>0.316––
PEG_R2D_C_N<2>0.312––
PEG_R2D_C_N<3>0.314––
PEG_R2D_C_N<4>0.315––
PEG_R2D_C_N<5>0.316––
PEG_R2D_C_N<6>0.315––
PEG_R2D_C_N<7>0.316––
PEG_R2D_N<4>0.382––
PEG_R2D_P<0>0.378––
PEG_R2D_P<1>0.380––
PEG_R2D_P<2>0.381––
PEG_R2D_P<6>0.381––
PEGCLKRQA_L_GPIO470.620––
PEGCLKRQB_L_GPIO560.552––
PEX_CLKREQ_L0.62––
PEX_CLKREQ_L_R0.633––
PEX_TSTCLK_O_N0.451––
PEX_TSTCLK_O_P0.453––
PICKB_L0.686––
PLLFILT_GYROOL––
PLLFILT_GYRO1OL––
PLT_RESET_L0.530––
PLT_RESET_LS1V1_L0.132––
PLT_RST_BUF_L0.435––
PLT_RST_CPU_BUF_L0.091––
PM_BATLOW_L0.573––
PM_CLK32K_SUSCLK_R0.602––
PM_CLKRUN_L0.636––
PM_DSW_PWRGD0.738––
PM_MEM_PWRGD0.306––
PM_MEM_PWRGD_LOL––
PM_MEM_PWRGD_R0.437––
PM_PCH_PWROK0.656––
PM_PCH_SYS_PWROK0.740––
PM_PWRBTN_L0.5733.400–
PM_RSMRST_L0.632––
PM_S0_PGOOD0.671––
PM_SLP_S3_L0.510––
PM_SLP_S3_R_L0.459––
PM_SLP_S4_L0.518––
PM_SLP_S5_L0.588––
PM_SLP_SUS_L0.597––
PM_SUS_EN0.752––
PM_SYNC0.470––
PM_SYSRST_L0.638––
PM_THRMTRIP_B_LOL––
PM_THRMTRIP_L0.383––
PM_THRMTRIP_L_R0.414––
PM_WLAN_EN_L0.936––
PP0V75_S0_DDRVTT0.165––
PP0V75_S3_MEM_VREFCA_A0.424––
PP0V75_S3_MEM_VREFCA_B0.423––
PP0V75_S3_MEM_VREFDQ_A0.412––
PP0V75_S3_MEM_VREFDQ_B0.407––
PP1V0_S0GPU_ISNS0.138––
PP1V2_S5_SMC_VDDC0.516––
PP1V05_GPU_FB_DLL_AVDD0.140––
PP1V05_GPU_FB_PLL_AVDD0.139––
PP1V05_GPU_IFPAB_PLLVDD0.267––
PP1V05_GPU_IFPCD_IOVDD0.139––
PP1V05_GPU_IFPEF_IOVDD0.138––
PP1V05_GPU_PEX_PLLVDD0.139––
PP1V05_GPU_PLLVDD0.138––
PP1V05_GPU_SP_PLLVDD0.138––
PP1V05_PCHVCCIO_S00.046––
PP1V05_S00.011––
PP1V5_S00.376––
PP1V5_S0_AUDIO_DIG0.377––
PP1V05_S0_CPU_VCCPQE0.012––
PP1V5_S0_LDO0.565––
PP1V05_S0_P1V05TBTFET0.046––
PP1V05_S0_PCH_VCCADPLLA_F0.041––
PP1V05_S0_PCH_VCCADPLLA_R0.041––
PP1V05_S0_PCH_VCCADPLLB_F0.044––
PP1V05_S0_PCH_VCCADPLLB_R0.044––
PP1V05_S0_PCH_VCCCLKDMI_F0.040––
PP1V05_S0_PCH_VCCCLKDMI_R0.046––
PP1V5_S0_RIO0.565––
PP1V5_S3_CPU_VCCDQ0.106––
PP1V5_S3RS0_CPUDDR0.102––
PP1V5_S3RS0_FET0.106––
PP1V05_SUS0.494––
PP1V05_TBTCIO0.192––
PP1V05_TBTLC0.154––
PP1V5R1V35_GPU_REG_R0.163–177.800R
PP1V5R1V35_MEM0.224––
PP1V5R1V35_S0GPU0.163––
PP1V5R1V35_S30.224––
PP1V8_GPU_IFPA_IOVDD0.550––
PP1V8_S00.117–308.500R
PP1V8_S0_CPU_VCCPLL_R0.121––
PP1V8_S0_P1V5_LDO0.118––
PP3V3_GPU_IFPB_IOVDD0.560––
PP3V3_GPU_IFPX_PLLVDD0.492––
PP3V3_GPU_OVERTEMP0.328––
PP3V3_GPU_PEX_PLL_HVDD0.494––
PP3V3_S00.307––
PP3V3_S0_CPUTHMSNS_R0.370––
PP3V3_S0_DPMUX_UC_R0.30––
PP3V3_S0_GPUTHMSNS_R0.357––
PP3V3_S0_PCH_VCC3_3_CLK_F0.309––
PP3V3_S0_PCH_VCC3_3_CLK_R0.308––
PP3V3_S0_PCH_VCCA_DAC_F0.307––
PP3V3_S0_SSD_FLT0.306––
PP3V3_S0_SSD_R0.307––
PP3V3_S0GPU0.492––
PP3V3_S0GPU_MISC0.530––
PP3V3_S30.396––
PP3V3_S3_DPMUX_UC_R0.39––
PP3V3_S3_PSOC0.427––
PP3V3_S3_VREFMRGN_CTRLOL––
PP3V3_S3_VREFMRGN_DAC0.396––
PP3V3_S3RS4_BT_F0.429––
PP3V3_S40.423––
PP3V3_S4_TBT0.426––
PP3V3_S50.142––
PP3V3_S5_AVREF_SMC0.609––
PP3V3_S5_SMC_VDDA0.324––
PP3V3_SUS0.343––
PP3V3_SW_TBTAPWR0.379––
PP3V3_SW_TBTBPWR0.384––
PP3V3_TBTLC0.409––
PP3V3_TPAD_CONNOL––
PP3V3_WLANOL––
PP3V3_WLAN_FOL––
PP3V3_WLAN_ROL––
PP3V3RHV_SW_TBTAPWR0.562––
PP3V3RHV_SW_TBTBPWR0.576––
PP3V42_G3H0.333.400–
PP3V42_GH3_AUDIO_LC0.322––
PP4V5_AUDIO_ANALOG0.517––
PP5V_AUDIO_HPAMP0.421––
PP5V_S00.390.399–
PP5V_S0_AUDIO_AMP_L0.399––
PP5V_S0_AUDIO_AMP_R0.400––
PP5V_S0_CPUIMVP_VCC0.408––
PP5V_S0_CPUVCCIOS0_VCC0.400––
PP5V_S0_GFXIMVP_VDD0.39––
PP5V_S0_P1V5_LDO_BIAS0.492––
PP5V_S0_PCH_V5REF0.377––
PP5V_S0_PCHVCCIOS0_VCC0.398––
PP5V_S0_RMC_FLTOL––
PP5V_S0_VCCSAS0_VCC0.399––
PP5V_S0GPU_P1V05_GPU0.400––
PP5V_S0GPU_P1V35_GPU0.402––
PP5V_S30.452––
PP5V_S3_ALSCAMERA_F0.448––
PP5V_S3_DEBUG_ADC_AVDD_FILTOL––
PP5V_S3_LTUSB_A_F0.490––
PP5V_S3_LTUSB_A_ILIM0.482––
PP5V_S40.425––
PP5V_S4_AUDIO_XW0.421––
PP5V_S4_CUMULUS0.457––
PP5V_S50.4605.000–
PP5V_S5_P5VSUSFET_R0.459––
PP5V_S5RS4_CUMULUS0.457––
PP5V_SUS0.407––
PP5V_SUS_PCH_V5REFSUS0.398––
PP5V1_CHGR_VDD0.34––
PP5V1_CHGR_VDDP0.33––
PP5VR3V3_SW_LCD0.605.00–
PP5VR3V3_SW_LCD_ISNS0.635––
PP5VR3V3_SW_LCD_UF0.613––
PP15V_TBT0.566––
PP18V5_DCIN_CONN_ROL––
PP18V5_DCIN_FUSEOL19.000–
PPBUS_G3H0.445––
PPBUS_G3H_R0.453––
PPBUS_S0_LCDBKLT_FUSED0.445––
PPBUS_S0_LCDBKLT_PWR_SW0.906––
PPBUS_SW_BKL0.909––
PPBUS_SW_LCDBKLT_PWR0.909––
PPCPU_MEM_VREFDQ_A0.793––
PPCPU_MEM_VREFDQ_B0.802––
PPCPUVCCIO_S0_REG_R0.011–12.500R
PPDCIN_G3HOL20.000–
PPDCIN_G3H_CHGR0.642––
PPDCIN_G3H_INRUSH0.642––
PPDCIN_G3H_ISOLOL20.320–
PPHV_SW_TBTAPWR0.562––
PPHV_SW_TBTBPWR0.574––
PPPCHVCCIO_S0_REG_R0.040––
PPUSB_HUB2_VDD1V80.532––
PPUSB_HUB2_VDD1V8PLL0.603––
PPVBAT_G3H_CHGR_R0.450––
PPVBAT_G3H_CHGR_REG0.450––
PPVBAT_G3H_CONNOL––
PPVCCSA_S0_REG0.008––
PPVCCSA_S0_REG_R0.008–8.800R
PPVCORE_GPU0.030––
PPVCORE_S0_AXG0.002––
PPVCORE_S0_AXG1_L0.002–2.000R
PPVCORE_S0_AXG2_L0.002–2.000R
PPVCORE_S0_CPU0.001––
PPVCORE_S0_CPU_PH10.001–2.000R
PPVCORE_S0_CPU_PH20.001–2.000R
PPVCORE_S0_CPU_PH30.001–2.000R
PPVCORE_S0_GFX_PH10.030–35.000R
PPVCORE_S0_GFX_PH20.030–35.000R
PPVIN_G3H_P3V42G3H0.599––
PPVIN_S0_GFXIMVP_R0.45––
PPVIN_S5_HS_COMPUTING_ISNS0.443––
PPVIN_S5_HS_GPU_ISNS0.445––
PPVIN_S5_HS_OTHER_ISNS0.445––
PPVIN_SW_TBTBST0.522––
PPVOUT_G3_PCH_DCPRTC0.635––
PPVOUT_S0_LCDBKLT1.2255.000–
PPVOUT_S0_PCH_DCPSST0.531––
PPVRTC_G3H0.459––
PPVTTDDR_S3OL––
PSOC_F_CS_L0.712––
PSOC_MISO0.712––
PSOC_MOSI0.712––
PSOC_SCLK0.712––
PU_USBHUB_DN4NOL––
PU_USBHUB_DN4POL––
PVCCSA_EN0.547––
PVCCSA_PGOOD0.506––
RSUBIN_N0.580––
RSUBIN_P0.580––
RTC_RESET_L0.780––
S0PGD_BJT_GND_R0.104––
S0PGD_C1.985––
S5_PWRGD0.577––
SATA_HDD_D2R_P0.380––
SATA_PCIE_SEL0.792––
SATA_SSD_D2R_N0.409––
SATA_SSD_D2R_P0.750––
SATA_SSD_R2D_N0.787––
SATA_SSD_R2D_P0.787––
SATAMUX_EN_L0.790––
SATARDRVR_EN0.699––
SD_PWR_EN0.689––
SD_PWR_EN_PCH0.562––
SDCONN_STATE_CHANGE0.536––
SDCONN_STATE_CHANGE_INV0.504––
SDCONN_STATE_CHANGE_RIO0.547––
SMBUS_PCH_ALERT_L0.651––
SMBUS_PCH_CLK0.482––
SMBUS_PCH_DATA0.485––
SMBUS_SMC_0_S0_SCL0.724––
SMBUS_SMC_0_S0_SDA0.726––
SMBUS_SMC_1_S0_SCL0.542––
SMBUS_SMC_1_S0_SDA0.541––
SMBUS_SMC_2_S3_SCL0.734––
SMBUS_SMC_2_S3_SDA0.734––
SMBUS_SMC_3_SCL0.746––
SMBUS_SMC_3_SDA0.746––
SMBUS_SMC_5_G3_SCL0.53––
SMBUS_SMC_5_G3_SDA0.53––
SMC_ADAPTER_EN0.588––
SMC_BATLOW_L0.737––
SMC_BC_ACOK0.50––
SMC_BC_ACOK_VCC0.573––
SMC_BIL_BUTTON_L0.751––
SMC_CHGR_BMON_INSENSE_R0.748––
SMC_CHGR_BMON_ISENSE0.748––
SMC_CLK32K0.623––
SMC_CPU_GFX_ISENSE0.747––
SMC_CPU_HI_ISENSE0.746––
SMC_CPU_ISENSE0.746––
SMC_CPU_SA_ISENSE0.745––
SMC_CPU_SA_VSENSE0.749––
SMC_CPU_VSENSE0.740––
SMC_CPUVCCIO_ISENSE0.747––
SMC_DCIN_ISENSE0.748––
SMC_DCIN_VSENSE0.740––
SMC_DEBUGPRT_EN_L0.555––
SMC_DEBUGPRT_RX_L0.612––
SMC_DEBUGPRT_TX_L0.614––
SMC_DELAYED_PWRGD0.657––
SMC_DP_HPD_L0.746––
SMC_EXTAL0.770––
SMC_FAN_0_CTL0.748––
SMC_FAN_0_TACH0.753––
SMC_FAN_1_CTL0.750––
SMC_FAN_1_TACH0.751––
SMC_GFX_OVERTEMP0.695––
SMC_GFX_OVERTEMP_Q0.643––
SMC_GFX_OVERTEMP_R_L0.719––
SMC_GFX_THROTTLE_R_L0.705––
SMC_GFX_VSENSE0.742––
SMC_GPU_CORE_ISENSE0.747––
SMC_GPU_CORE_VSENSE0.742––
SMC_GPU_HI_ISENSE0.745––
SMC_GPU_P1V35_ISENSE0.745––
SMC_KBDLED_PRESENT_LOL––
SMC_LCDBKLT_ISENSE0.747––
SMC_LCDBKLT_VSENSE0.743––
SMC_LID0.476––
SMC_LID_R0.470––
SMC_LRESET_L0.560––
SMC_MANUAL_RST_L0.679––
SMC_ONOFF_L0.671––
SMC_OOB1_RX_L0.749––
SMC_OOB1_TX_L0.749––
SMC_OTHER_HI_ISENSE0.746––
SMC_P1V5MEM_ISENSE0.746––
SMC_PBUS_VSENSE0.741––
SMC_PCH_CORE_ISENSE0.748––
SMC_PECI_L0.749––
SMC_PECI_L_R0.749––
SMC_PM_G2_EN0.533––
SMC_PME_S4_DARK_L0.519––
SMC_PME_S4_WAKE_L0.579––
SMC_PROCHOT0.750––
SMC_RESET_L0.499––
SMC_ROMBOOT1.745––
SMC_RUNTIME_SCI_L0.629––
SMC_RX_L0.754––
SMC_S4_WAKESRC_EN0.706––
SMC_S5_PWRGD_VIN0.751––
SMC_SSD_ISENSE0.747––
SMC_SYS_KBDLED0.642––
SMC_SYS_KBDLED_ANALOGOL––
SMC_SYS_KBDLED_FILTEROL––
SMC_SYS_KBDLED_R0.647––
SMC_TBT_ISENSE0.746––
SMC_TBT_ISENSE_R0.745––
SMC_TCK0.753––
SMC_TDI0.752––
SMC_TDO0.751––
SMC_THRMTRIP0.747––
SMC_TMS0.751––
SMC_TPAD_RST_L0.468––
SMC_TX_L0.752––
SMC_WAKE_L0.750––
SMC_WAKE_SCI_L0.580––
SMC_X29_ISENSE0.749––
SMC_XTAL0.770––
SMC_XTAL_ROL––
SML_PCH_0_CLK0.590––
SML_PCH_0_DATA0.589––
SML_PCH_1_CLK0.543––
SML_PCH_1_DATA0.541––
SMS_ADDR_SELECTOL––
SMS_I2C_SELOL––
SMS_INT_L0.747––
SPI_ALT_CLK0.637––
SPI_ALT_CS_L0.630––
SPI_ALT_MISO0.535––
SPI_ALT_MOSI0.559––
SPI_CLK0.596––
SPI_CLK_R0.570––
SPI_CS0_L0.587––
SPI_CS0_R_L0.563––
SPI_DESCRIPTOR_OVERRIDE0.770––
SPI_DESCRIPTOR_OVERRIDE_L0.748––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.450––
SPI_MISO0.523––
SPI_MLB_CLK0.647––
SPI_MLB_CS_L0.629––
SPI_MLB_MISO0.524––
SPI_MLB_MOSI0.524––
SPI_MOSI0.527––
SPI_MOSI_R0.525––
SPI_SMC_CLK0.665––
SPI_SMC_CS_L0.654––
SPI_SMC_MISO0.537––
SPI_SMC_MOSI0.554––
SPI_WP_L0.646––
SPIROM_USE_MLB0.538––
SPKR_L_GAIN0.596––
SPKR_MATCH_DRV0.677––
SPKR_MATCH_DRV_R0.637––
SPKR_R_GAIN0.601––
SPKRAMP_LIN_N0.596––
SPKRAMP_LIN_P0.596––
SPKRAMP_RIN_N0.597––
SPKRAMP_RIN_P0.597––
SPKRCONN_L_IDOL––
SPKRCONN_L_OUT_N0.505––
SPKRCONN_L_OUT_P0.500––
SPKRCONN_R_IDOL––
SPKRCONN_R_OUT_N0.502––
SPKRCONN_R_OUT_P0.502––
SPKRCONN_SL_OUT_N0.619––
SPKRCONN_SL_OUT_P0.618––
SPKRCONN_SR_OUT_N0.623––
SPKRCONN_SR_OUT_P0.622––
SSD_CLKREQ_L0.566––
SSD_P3V3S0_EN0.460––
SSD_RESET_L0.433––
SUS_PGOOD_CT0.639––
SUS_PGOOD_MR_L0.693––
SYS_DETECT_LOL––
SYS_ONEWIRE0.678––
SYS_PWROK_R0.684––
SYS_TDM_ONEWIRE0.747––
SYSCLK_25M_B_GND0.001––
SYSCLK_CLK25M_SB0.444––
SYSCLK_CLK25M_SB_R0.610––
SYSCLK_CLK25M_TBT_R0.676––
SYSCLK_CLK25M_X10.455––
SYSCLK_CLK25M_X20.457––
SYSCLK_CLK25M_X2_R0.458––
SYSCLK_CLK32K_RTC0.464––
TBT_A_BIAS0.768––
TBT_A_CONFIG1_BUF0.561––
TBT_A_CONFIG1_RC0.834––
TBT_A_CONFIG2_RC0.551––
TBT_A_D2R_N<1>0.393––
TBT_A_D2R_P<1>0.397––
TBT_A_D2R1_AUXDDC_N0.716––
TBT_A_D2R1_AUXDDC_P0.720––
TBT_A_DP_PWRDN0.656––
TBT_A_HPD0.834––
TBT_A_HV_EN0.475––
TBT_A_LSRX0.555––
TBT_A_LSRX_UNBUF0.687––
TBT_A_LSTX0.539––
TBT_A_R2D_C_P<1>0.230––
TBT_B_BIAS0.780––
TBT_B_CIO_SEL0.555––
TBT_B_CONFIG1_BUF0.552––
TBT_B_CONFIG1_RC0.846––
TBT_B_CONFIG2_RC0.552––
TBT_B_D2R1_AUXDDC_P0.706––
TBT_B_DP_PWRDN0.662––
TBT_B_HPD0.848––
TBT_B_HV_EN0.475––
TBT_B_LSRX_UNBUF0.694––
TBT_B_LSTX0.541––
TBT_B_R2D_C_P<0>0.228––
TBT_B_R2D_C_P<1>0.231––
TBT_CIO_PLUG_EVENT0.553––
TBT_CIO_PLUG_EVENT_ISOL0.687––
TBT_CLKREQ_ISOL_L0.465––
TBT_CLKREQ_L0.456––
TBT_DDC_XBAR_EN_L0.580––
TBT_EN_CIO_PWR0.455––
TBT_EN_CIO_PWR_L0.522––
TBT_EN_LC_1V050.466––
TBT_EN_LC_3V30.693––
TBT_EN_LC_ISOL0.466––
TBT_GO2SX_BIDIR0.514––
TBT_GPIO_90.509––
TBT_GPIO_140.550––
TBT_MONOBSN0.205––
TBT_MONOBSP0.208––
TBT_PCIE_RESET_L0.464––
TBT_PWR_EN0.555––
TBT_PWR_EN_PCH0.565––
TBT_PWR_ON_POC_RST_L0.588––
TBT_RBIAS0.799––
TBT_RSENSE0.004––
TBT_SPI_CLK0.564––
TBT_SPI_CS_L0.662––
TBT_SPI_MISO0.633––
TBT_SPI_MOSI0.556––
TBT_SW_RESET_L0.610––
TBT_SW_RESET_R_L0.602––
TBT_TEST_EN0.002––
TBT_TEST_PWR_GOOD0.001––
TBT_TMU_CLK_IN0.640––
TBT_TMU_CLK_OUT0.557––
TBTACONN_1_COL––
TBTACONN_7_COL––
TBTACONN_20_RC0.579––
TBTAPWRSW_ISET_S00.490––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.490––
TBTAPWRSW_ISET_S3_ROL––
TBTAPWRSW_ISET_V3P30.490––
TBTBCONN_1_COL––
TBTBCONN_7_COL––
TBTBCONN_20_RC0.586––
TBTBPWRSW_ISET_S00.490––
TBTBPWRSW_ISET_S0_ROL––
TBTBPWRSW_ISET_S30.490––
TBTBPWRSW_ISET_S3_ROL––
TBTBPWRSW_ISET_V3P30.490––
TBTBST_BOOST0.522––
TBTBST_EN_UVLO0.514––
TBTBST_FBXOL––
TBTBST_INTVCC0.575––
TBTBST_PWREN_DIV_LOL––
TBTBST_PWREN_L0.440––
TBTBST_RT0.690––
TBTBST_SHDN_DIV0.443––
TBTBST_SNS10.002––
TBTBST_SNS20.002––
TBTBST_SS0.681––
TBTBST_VC0.696––
TBTPOCRST_CT0.637––
TBTPOCRST_MR_L0.667––
TBTROM_HOLD_L0.744––
TBTROM_WP_L0.747––
TDM_ONEWIRE_MLBOL––
TDM_ONEWIRE_MPMOL––
TDM_PD_BASEOL––
TDM_PD_BASE_ROL––
TDM_PD_DSOL––
TDM_RXOL––
TP_DPMUX_UC_P100.64––
TP_DPMUX_UC_P110.63––
TP_DPMUX_UC_P120.64––
TP_DPMUX_UC_P130.63––
TP_DPMUX_UC_P470.63––
TP_GPU_JTAG_TCK0.734––
TP_GPU_JTAG_TDI0.734––
TP_GPU_JTAG_TDO0.733––
TP_GPU_PGOOD20.63––
TP_ISSP_SCLK_P1_10.710––
TP_ISSP_SDATA_P1_00.708––
TP_PCIE_CLK100M_FW_N0.390––
TP_PCIE_CLK100M_FW_P0.390––
TP_SMC_MD1OL––
TP_SMC_MPM5_LED_CHG0.752––
TP_SMC_MPM5_LED_PWR0.748––
TP_SMC_TRST_LOL––
TP_TBT_MONDC10.377––
TP_XCVR_ADC_RSTN0.702––
TPAD_VBUS_EN0.707––
US_HS_MIC0.540––
USB_BT_CONN_N0.711––
USB_BT_CONN_P0.718––
USB_BT_N0.708––
USB_BT_P0.711––
USB_BT_WAKE_N0.720––
USB_BT_WAKE_P0.730––
USB_CAMERA_CONN_N0.564––
USB_CAMERA_CONN_P0.565––
USB_CAMERA_N0.561––
USB_CAMERA_P0.562––
USB_EXTA_MUXED_N0.588––
USB_EXTA_MUXED_P0.588––
USB_EXTA_N0.559––
USB_EXTA_OC_L0.492––
USB_EXTA_P0.566––
USB_EXTB_EHCI_N0.520––
USB_EXTB_EHCI_P0.520––
USB_EXTB_N0.527––
USB_EXTB_OC_L0.671––
USB_EXTB_P0.527––
USB_EXTB_SEL_XHCI0.539––
USB_EXTB_XHCI_N0.522––
USB_EXTB_XHCI_P0.522––
USB_EXTD_SEL_XHCI0.653––
USB_EXTD_XHCI_N0.555––
USB_EXTD_XHCI_P0.555––
USB_HUB_CFG_SEL00.770––
USB_HUB_CFG_SEL10.770––
USB_HUB_NONREM00.768––
USB_HUB_NONREM10.771––
USB_HUB_RBIAS0.787––
USB_HUB_RESET_L0.771––
USB_HUB_TEST0.102––
USB_HUB_UP_N0.554––
USB_HUB_UP_P0.554––
USB_HUB_VBUS_DET0.771––
USB_HUB_XTAL10.785––
USB_HUB_XTAL20.748––
USB_ILIM0.513––
USB_ILIM_ROL––
USB_LT1_N0.591––
USB_LT1_P0.591––
USB_PWR_EN0.479––
USB_SMC_N0.697––
USB_SMC_P0.698––
USB_TPAD_N0.703––
USB_TPAD_P0.704––
USB_TPAD_R_P0.696––
USB3_EXTA_RX_RC_N0.392––
USB3_EXTA_RX_RC_P0.392––
USB3_EXTA_TX_C_NOL––
USB3_EXTA_TX_C_POL––
USB3_EXTA_TX_N0.358––
USB3_EXTA_TX_P0.358––
USB3_EXTB_RX_RC_N0.385––
USB3_EXTB_RX_RC_P0.385––
USB3_EXTB_TX_C_NOL––
USB3_EXTB_TX_C_POL––
USB3_EXTB_TX_NOL––
USB3_EXTB_TX_P0.355––
USE_HDD_OOB_L0.592––
VBIAS_DAC0.739––
VCCSA_VSENSE_IN0.009––
VCCSAISNS_R_NOL––
VCCSAISNS_R_P0.785––
VCCSAS0_AGND0.003––
VCCSAS0_BOOT_RC0.544––
VCCSAS0_CS_N0.008––
VCCSAS0_CS_P0.008––
VCCSAS0_DRVH0.585––
VCCSAS0_DRVL0.446––
VCCSAS0_FSEL0.002––
VCCSAS0_LL0.008–8.800R
VCCSAS0_OCSET0.527––
VCCSAS0_RTN0.001––
VCCSAS0_RTN_DIV0.520––
VCCSAS0_SET_ROL––
VCCSAS0_SET00.547––
VCCSAS0_SET10.548––
VCCSAS0_SREF0.544––
VCCSAS0_VBST0.544––
VCCSAS0_VO0.526––
VMON_3V3_DIVOL––
VMON_Q2_BASEOL––
VMON_Q3_BASE1.108––
VMON_Q4_BASE1.010––
VOUT_S0_LCDBKLT_DIVOL––
VOUT_S0_LCDBKLT_XW1.253––
VREFMRGN_CA_SODIMMA_BUFOL––
VREFMRGN_CA_SODIMMA_ENOL––
VREFMRGN_CA_SODIMMB_BUFOL––
VREFMRGN_CA_SODIMMB_ENOL––
VREFMRGN_DQ_SODIMMA_BUFOL––
VREFMRGN_DQ_SODIMMA_ENOL––
VREFMRGN_DQ_SODIMMB_BUFOL––
VREFMRGN_DQ_SODIMMB_ENOL––
VREFMRGN_FRAMEBUF_BUFOL––
VREFMRGN_FRAMEBUF_BUF_ROL––
VREFMRGN_FRAMEBUF_ENOL––
VREFMRGN_MEMVREG_BUFOL––
VREFMRGN_MEMVREG_ENOL––
VREFMRGN_MEMVREG_FBVREFOL––
VREFMRGN_MEMVREG_FBVREF_ROL––
VREFMRGN_SODIMMA_DQOL––
VREFMRGN_SODIMMB_DQOL––
VREFMRGN_SODIMMS_CAOL––
VSNS_CPU_VCORE_RMC_OUTOL––
VTTCLAMP_EN0.443––
VTTCLAMP_L0.175––
WIFI_EVENT_L0.748––
WOL_EN0.563––
WS_CONTROL_KBD0.468––
WS_CONTROL_KEY0.468––
WS_KBD_ONOFF_L1.669––
WS_KBD10.707––
WS_KBD20.708––
WS_KBD30.707––
WS_KBD40.708––
WS_KBD50.707––
WS_KBD60.708––
WS_KBD70.707––
WS_KBD80.708––
WS_KBD90.708––
WS_KBD100.708––
WS_KBD110.708––
WS_KBD120.708––
WS_KBD130.708––
WS_KBD140.708––
WS_KBD15_C0.717––
WS_KBD15_CAP0.766––
WS_KBD16_NUMOL––
WS_KBD16N0.715––
WS_KBD170.708––
WS_KBD180.703––
WS_KBD190.708––
WS_KBD200.710––
WS_KBD210.710––
WS_KBD220.710––
WS_KBD230.710––
WS_LEFT_OPTION_KBD0.467––
WS_LEFT_OPTION_KEY0.474––
WS_LEFT_SHIFT_KBD0.468––
WS_LEFT_SHIFT_KEY0.467––
X29THMSNS_A00.672––
XDP_BPM_L<0>0.387––
XDP_BPM_L<1>0.385––
XDP_BPM_L<2>0.387––
XDP_BPM_L<3>0.385––
XDP_BPM_L<4>0.385––
XDP_BPM_L<5>0.385––
XDP_BPM_L<6>0.389––
XDP_BPM_L<7>0.385––
XDP_CPU_CFG<0>1.382––
XDP_CPU_CLK100M_N0.393––
XDP_CPU_CLK100M_P0.398––
XDP_CPU_PRDY_L0.387––
XDP_CPU_PREQ_L0.386––
XDP_CPU_PWRBTN_L0.577––
XDP_CPU_PWRGD1.474––
XDP_CPU_TCK0.060––
XDP_CPU_TDI0.066––
XDP_CPU_TDO0.066––
XDP_CPU_TMS0.063––
XDP_CPU_TRST_L0.055––
XDP_CPURST_L1.092––
XDP_DA0_PCH_GPIO59_USB_EXTA_OC_0.500––
XDP_DA0_USB_EXTA_OC_L0.529––
XDP_DA1_PCH_GPIO40_USB_EXTB_OC_0.669––
XDP_DA1_USB_EXTB_OC_L0.703––
XDP_DA2_PCH_GPIO41_USB_EXTC_OC_0.709––
XDP_DA2_USB_EXTC_OC_L0.736––
XDP_DA3_PCH_GPIO42_USB_EXTD_OC_0.650––
XDP_DA3_USB_EXTD_OC_L0.678––
XDP_DB0_USB_EXTB_OC_EHCI_L0.710––
XDP_DB1_PCH_GPIO9_USB_EXTD_OC_E0.668––
XDP_DB1_USB_EXTD_OC_EHCI_L0.701––
XDP_DB2_AP_PWR_EN0.494––
XDP_DB2_PCH_GPIO10_AP_PWR_EN0.462––
XDP_DB3_PCH_GPIO14_SDCONN_STATE0.535––
XDP_DB3_SDCONN_STATE_CHANGE0.569––
XDP_DBRESET_L0.650––
XDP_DC0_ISOLATE_CPU_MEM_L0.630––
XDP_DC0_PCH_GPIO28_ISOLATE_CPU_0.596––
XDP_DC1_MXM_GOOD0.615––
XDP_DC1_PCH_GPIO35_MXM_GOOD0.582––
XDP_DC2_DP_AUXCH_ISOL0.737––
XDP_DC2_PCH_GPIO21_DP_AUXCH_ISO0.708––
XDP_DC3_PCH_GPIO19_SATARDRVR_EN0.692––
XDP_DC3_SATARDRVR_EN0.725––
XDP_DD0_DP_GPU_TBT_SEL0.608––
XDP_DD0_PCH_GPIO36_DP_GPU_TBT_S0.577––
XDP_DD1_JTAG_ISP_TCK0.669––
XDP_DD1_PCH_GPIO37_JTAG_ISP_TCK0.641––
XDP_DD2_AUD_IPHS_SWITCH_EN0.603––
XDP_DD2_PCH_GPIO16_AUD_IPHS_SWI0.570––
XDP_DD3_ENET_LOW_PWR0.591––
XDP_DD3_PCH_GPIO49_ENET_LOW_PWR0.559––
XDP_FC00.612––
XDP_FC0_PCH_GPIO150.579––
XDP_FC10.604––
XDP_FC1_PCH_GPIO00.572––
XDP_OBSDATA_B<0>0.380––
XDP_OBSDATA_B<1>0.380––
XDP_OBSDATA_B<2>0.386––
XDP_OBSDATA_B<3>0.383––
XDP_PCH_PWRBTN_L0.575––
XDP_PCH_S5_PWRGD1.474––
XDP_PCH_TCK0.053––
XDP_PCH_TDI0.502––
XDP_PCH_TDO0.503––
XDP_PCH_TMS0.502––
XDP_VR_READY1.072––
XDPPCH_PLTRST_L1.520––
Z2_CLKIN0.718––
Z2_CS_L0.715––
Z2_HOST_INTN0.713––
Z2_KEY_ACT_L0.711––
Z2_MISO0.713––
Z2_MOSI0.714––
Z2_SCLK0.713––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3332?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3332: diode 0.445. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3332?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3332: diode 0.33, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3332?

OpenBoardData's known-good values for PP5V_S5 on the 820-3332: diode 0.460, voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3332 board?

Open your own 820-3332 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License