Apple laptop board · OpenBoardData

820-3023 known-good readings

Known-good readings for the Apple laptop board 820-3023: 380 nets, including 25 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 25 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3023.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 25 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 4

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.00––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, per its name (G3H = always on); it should be present whenever the board has power. The archive lists a diode reading of 0.00 for this net, which is a guide only and depends on board state. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading near 0.00 usually suggests a short to ground on that rail, but confirm with a resistance check before suspecting any part; no known-good voltage reading is recorded here, so compare against a known-good board.

PPBUS_G3H0.435––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the "G3H" suffix indicates it is always-on (from the name). The archive lists one known-good reading: diode 0.435 to ground, with no condition noted. Check it unpowered in diode mode from PPBUS_G3H to ground, then measure its voltage with power applied; no known-good voltage is listed here. A diode reading far from 0.435 usually points to a short or a leaky part on the rail, but one reading isn't proof — confirm with a second measurement before replacing anything.

PPDCIN_G3H0.652––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, judged from its name; it's the DC input that should be present whenever the charger is connected. The archive lists one known-good diode reading of 0.652 to ground, with no condition noted, and no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on it. A diode reading far from 0.652 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PPVBAT_G3H_CHGR_REG0.435––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a battery-side rail on the 820-3023; from its name, G3H means it is always on, and CHGR points to the charger circuit. The only known-good reading here is a diode value of 0.435 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading is available here, so compare against a matching rail on a known-good board. A diode reading far from 0.435 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part.

S5 and SUS: standby 7

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V05_SUS0.411––
AI: what PP1V05_SUS is and how to check it
  • What it is: PP1V05_SUS is a 1.05 V standby rail; the "SUS" in the name indicates it stays up in standby, and "1V05" indicates its nominal voltage. This is from the name only, not from board data.
  • Known-good reading: diode 0.411 to ground, from the community archive (no condition recorded). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V05_SUS to ground; then apply power and measure the rail voltage.
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail, while a much higher or open reading points to a broken connection. Confirm with a second measurement before replacing anything.
PP3V3_S50.290––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the S5/SUS part of the name marks it as a standby rail that should be present before the board fully powers on. The archive lists one known-good reading: diode 0.290 in diode mode to ground, with the board unpowered. Check it by measuring diode mode from PP3V3_S5 to ground with power off, then measure the voltage on the rail with power applied. No known-good voltage reading is recorded here, so compare against a matching standby rail or a known-good board. A diode reading far from 0.290 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S5_AVREF_SMC0.470––
AI: what PP3V3_S5_AVREF_SMC is and how to check it
  • What it is: From its name, PP3V3_S5_AVREF_SMC is a 3.3 V standby (S5/SUS) reference rail feeding the SMC. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.470 to ground (no condition given). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage, expecting about 3.3 V from the name.
  • If it's far off: a low diode reading or a collapsed voltage usually points to a shorted load or a failed source on that rail. Confirm with a second measurement before replacing anything.
PP3V3_S5_SMC_AVCC0.288––
AI: what PP3V3_S5_SMC_AVCC is and how to check it
  • What it is: PP3V3_S5_SMC_AVCC is a 3.3 V standby rail feeding the SMC's analog supply; the S5 and SUS naming marks it as a standby-stage rail (from the name, not from board data).
  • Known-good reading: diode 0.288 to ground, no condition recorded. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.288. Then apply power and measure the rail voltage; no known-good voltage is listed, so compare against a matching standby rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail, and a missing or low voltage points to the standby supply or its enable. Confirm with a second measurement before replacing anything.
PP3V3_SUS0.373––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail; the SUS in the name indicates it stays up in standby, before the main rails come on. The archive gives one known-good diode reading of 0.373 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.373 usually points to a short or a leaky part on that rail, but a single reading isn't proof, so compare against a matching standby rail or a known-good board before replacing anything.

PP5V_S50.438––
AI: what PP5V_S5 is and how to check it
  • What it is: PP5V_S5 is the 5 V standby rail, from its name (S5/SUS = standby). It should be present before the board fully powers on.
  • Known-good reading: diode 0.438 to ground, from the readings archive. That's a community figure and a guide only; no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S5 to ground and compare with 0.438. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher or open reading suggests a broken connection or missing component. Confirm with a voltage measurement before replacing anything.
PPBUS_S5_HS_COMPUTING_ISNS0.444––
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it

PPBUS_S5_HS_COMPUTING_ISNS is a PPBUS sense line for the high-side computing rail; the S5/SUS in the name indicate it belongs to the standby stage (from the name). The archive lists one known-good diode reading of 0.444, with no condition recorded and no known-good voltage or resistance value here. Check it with the board unpowered in diode mode from the net to ground, then measure its voltage with power applied. A diode reading far from 0.444 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board.

S3: memory 5

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V5_S30.145––
AI: what PP1V5_S3 is and how to check it

PP1V5_S3 is a 1.5 V rail; the S3 suffix, from its name, places it in the memory stage of startup. The archive lists one known-good reading: diode 0.145 to ground, with no condition noted, and no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from PP1V5_S3 to ground, then power up and measure the voltage. A diode reading far from 0.145 usually points to a short or a leaky part on the rail, but a single reading doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP1V5_S3RS00.051––
AI: what PP1V5_S3RS0 is and how to check it

PP1V5_S3RS0 is a 1.5 V rail in the S3 (memory) startup stage, inferred from its name. The archive lists one known-good diode reading of 0.051 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, then measure the voltage with power applied. A diode reading far from 0.051 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V5_S3RS0_FET_R0.051––
AI: what PP1V5_S3RS0_FET_R is and how to check it
  • What it is: From its name, PP1V5_S3RS0_FET_R is a 1.5 V rail in the S3 (memory) startup stage. The FET suffix suggests it's switched through a FET, but that's from the name only.
  • Known-good reading: diode 0.051 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If it's far off: a much lower diode reading points to a short on the rail, but one reading isn't proof — compare against the same rail on a known-good board before replacing anything.
PP3V3_S30.342––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that, judging by its name, comes up at the S3 (memory) stage of the 820-3023's power sequence. The archive lists one known-good reading for it: diode 0.342, with no condition noted, so treat it as a guide only. To check it, power the board off and measure diode mode from PP3V3_S3 to ground, then apply power and measure the voltage on the rail. No known-good voltage reading is recorded here, so compare against a known-good board or the matching rail on the other side of a pair. A diode reading far from 0.342 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP5V_S30.418––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is the 5 V rail for the S3 (memory) stage, judged from its name; the archive lists one known-good diode reading of 0.418 to ground. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.418 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

S0: running 9

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.012––
AI: what PP1V05_S0 is and how to check it
  • What it is: From the name, PP1V05_S0 is a 1.05 V rail that is active in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: Diode mode to ground is 0.012, from the readings archive. That's a very low value, so treat it as a guide only, and note the board's state when it was taken. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from PP1V05_S0 to ground. Then power the board and measure the voltage on the rail.
  • If it's far off: A much lower diode reading than 0.012 usually points to a short or a leaky part on the rail. A missing or wrong voltage with power applied points to the rail not coming up. Either way, confirm with a second measurement before replacing anything.
PP1V8_S00.135––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail; the "S0" suffix, from its name, marks it as a running-state supply. The only known-good reading here is a diode value of 0.135 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is available here. A diode reading far from 0.135 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S00.301––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 state, meaning the board is fully running (from the name). The archive lists a known-good diode reading of 0.301 to ground on this net; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far below 0.301 suggests a short or a leaky part on the rail; a far higher or open reading points to a broken connection or missing part. A wrong voltage with a normal diode reading points more to the supply or enable side than to the rail itself.

PP3V3_S0_CPUTHMSNS_R0.310––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding the CPU thermal-sense circuit. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.310 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode to ground on PP3V3_S0_CPUTHMSNS_R; then power on and measure its voltage, expecting about 3.3 V once the board is in S0.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage points to the rail not being enabled. These are likely causes, not confirmed ones.
PP5V_S00.358––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, judged from its name. The archive lists one known-good diode reading for it: 0.358 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board awake. No known-good voltage reading is listed here, so compare against a matching 5 V rail or a known-good board. A diode reading far below 0.358 usually points to a short or a leaky part on the rail; far above it suggests an open connection or a missing component.

PP5V_S0_CPUVCCIOS0_VCC0.357––
AI: what PP5V_S0_CPUVCCIOS0_VCC is and how to check it

PP5V_S0_CPUVCCIOS0_VCC is a 5 V rail that, from its name, runs in the S0 (running) state and feeds the CPU's VCCIO for the S0 domain. The archive lists one known-good reading: diode mode to ground 0.357, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage is listed here. A diode reading far below 0.357 suggests a short or a leaky load on the rail, while a much higher one can mean an open path; either way, confirm with a second measurement before suspecting a part.

PP5V_S0_VCCSAS0_VCC0.357––
AI: what PP5V_S0_VCCSAS0_VCC is and how to check it

PP5V_S0_VCCSAS0_VCC is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds the SAS/SATA section. The archive's only known-good figure is a diode reading of 0.357 to ground, with no stated condition; there is no known-good voltage or resistance reading here.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.357.
  • Then power the board and measure the voltage; it should sit near 5 V, though that value isn't from this board's data.

A diode reading far below 0.357 usually points to a short or a leaky part on the rail; far above it suggests an open path. Either way, confirm with a voltage measurement before suspecting a part.

PPVCORE_S0_AXG_R0.007 1.7GHz i50.000––
AI: what PPVCORE_S0_AXG_R is and how to check it

PPVCORE_S0_AXG_R is the CPU core supply rail; the S0 in the name indicates it is active in the running state, and AXG is Apple's label for this core rail (from the name).

  • Known-good readings in the archive: diode 0.007 with a 1.7GHz i5 fitted, and diode 0.000 in another entry. Both are very low, which is normal for a core rail feeding a large die.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running.
  • No known-good voltage reading is recorded here, so compare against a known-good board of the same spec.
  • A diode reading far above the known-good range usually points to an open feed, a bad inductor or a failed regulator; a short to ground with the board off is a different fault and needs tracing before any part is replaced.
PPVCORE_S0_CPU_PH10.008 1.7GHz i50.000––
AI: what PPVCORE_S0_CPU_PH1 is and how to check it

PPVCORE_S0_CPU_PH1 is the CPU core power rail's switching phase node; the S0 in the name indicates it is active in the running state (from the name). The archive lists a diode reading of 0.008 on a 1.7GHz i5 board and 0.000 on another, so readings vary with the board's state and are only a guide. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied. A reading far from the known-good values usually points to a short or a faulty phase component, but no known-good voltage reading exists here, so compare against a matching rail or a known-good board before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD0.411––
AP_CLKREQ_Q_L0.00––
AP_RESET_L0.386––
AUD_SPKR_RWFR_OUT_P0.00––
BCM57765_MISO0.00––
BKL_EN0.513––
BKL_FLTR0.505––
BKL_FSET0.512––
BKL_ISEN10.574––
BKL_ISEN20.574––
BKL_ISEN30.574––
BKL_ISEN40.570––
BKL_ISEN50.572––
BKL_ISEN60.569––
BKL_ISET0.509––
BKL_PWM0.470––
BKL_SCL0.420––
BKL_SDA0.420––
BKL_VSYNC_R0.506––
BKLT_PLT_RST_L0.382––
BMON_AMUX_OUT0.690––
CHGR_ACIN0.464––
CHGR_AGATE0.573––
CHGR_AMON0.668––
CHGR_BGATE0.607––
CHGR_BMON0.686––
CHGR_BOOT0.548––
CHGR_CELL0.033––
CHGR_CSI_N0.534––
CHGR_CSI_P0.533––
CHGR_CSO_N0.440––
CHGR_CSO_P0.440––
CHGR_CSO_R_N0.440––
CHGR_CSO_R_P0.440––
CHGR_DCIN0.572––
CHGR_DCIN_D_R0.578––
CHGR_ICOMP0.688––
CHGR_LGATE0.407––
CHGR_PHASE0.439––
CHGR_RST_L0.404––
CHGR_SGATE0.572––
CHGR_UGATE0.815––
CHGR_VCOMP0.684––
CHGR_VCOMP_ROL––
CHGR_VFRQ0.467––
CHGR_VNEG0.473––
CHGR_VNEG_R0.518––
CPU_AXG_SENSE_N0.000––
CPU_AXG_SENSE_P0.008––
CPU_AXG_SENSE_R0.003––
CPU_PECI_R0.462––
CPU_PROCHOT_BUF0.743––
CPU_PROCHOT_L0.032––
CPU_PROCHOT_L_R0.610––
CPU_THERMD_N0.600––
CPU_THERMD_P0.610––
CPU_VCCSA_VID<1>0.310––
CPU_VCCSASENSE0.036––
CPU_VCCSENSE_N0.000––
CPU_VCCSENSE_P0.010––
CPU_VCCSENSE_R0.003––
CPU_VIDALERT_L0.041––
CPU_VIDSCLK0.034––
CPU_VIDSOUT0.037––
CPUIMVP_AXG_PGOOD0.543––
CPUIMVP_BOOT10.573––
CPUIMVP_BOOT1_RC0.573––
CPUIMVP_BOOT1G0.576––
CPUIMVP_FBA0.592––
CPUIMVP_FBA_R0.014––
CPUIMVP_FBB0.601––
CPUIMVP_FBB_R0.011––
CPUIMVP_IMAXA0.556––
CPUIMVP_IMAXB0.537––
CPUIMVP_ISNS1_N0.010––
CPUIMVP_ISNS1_P0.010––
CPUIMVP_ISNS1G_N0.008––
CPUIMVP_ISNS1G_P0.008––
CPUIMVP_ISUM0.100––
CPUIMVP_ISUM_IOUT0.522––
CPUIMVP_ISUM_N0.014––
CPUIMVP_ISUM_R0.115––
CPUIMVP_ISUM_R_N0.698––
CPUIMVP_ISUM_R_P0.700––
CPUIMVP_ISUM1_P0.023––
CPUIMVP_ISUMG_IOUT0.521––
CPUIMVP_ISUMG_N0.011––
CPUIMVP_ISUMG_P0.023––
CPUIMVP_ISUMG_R_N0.698––
CPUIMVP_ISUMG_R_P0.698––
CPUIMVP_LGATE10.447––
CPUIMVP_LGATE1G0.448––
CPUIMVP_NTC0.536––
CPUIMVP_NTCG0.620––
CPUIMVP_PGOOD0.477––
CPUIMVP_PHASE10.008 1.7GHz i50.000–0.000R
CPUIMVP_PHASE1G0.007––
CPUIMVP_SLEW0.621––
CPUIMVP_TON0.606––
CPUIMVP_UGATE10.011––
CPUIMVP_UGATE1_R0.011––
CPUIMVP_UGATE1G0.657––
CPUIMVP_UGATE1G_R0.657––
CPUIMVP_VR_ON0.411––
CPUIMVP_VSWG0.007 1.7GHz i50.000––
CPUTHMSNS_ALERT_L0.666––
CPUTHMSNS_D2_N0.577––
CPUTHMSNS_D2_P0.578––
CPUTHMSNS_THM_L0.662––
CPUVCCIOS0_AGND0.000––
CPUVCCIOS0_DRVH0.441––
CPUVCCIOS0_DRVL0.402––
CPUVCCIOS0_EN0.465––
CPUVCCIOS0_FB0.350––
CPUVCCIOS0_FSEL0.000––
CPUVCCIOS0_LL0.015––
CPUVCCIOS0_OCSET0.442––
CPUVCCIOS0_PGOOD0.422––
CPUVCCIOS0_RTN0.349––
CPUVCCIOS0_SREF0.470––
CPUVCCIOS0_VBST0.478––
CPUVCCIOS0_VO0.440––
DP_A_EXT_HPD0.475––
DP_AUXCH_ISOL0.504––
DP_IG_D_HPD0.708––
DP_INT_AUX_CH_C_NOL––
DP_INT_AUX_CH_C_POL––
DP_INT_HPD_CONNOL––
DP_INT_ML_F_N<0>OL––
DP_INT_ML_F_N<1>OL––
DP_INT_ML_F_P<0>OL––
DP_INT_ML_F_P<1>OL––
ENET_LOW_PWR0.453––
G3_POWERON_L0.543––
GFXVSENSE_IN0.008––
GND_CPUIMVP_SGND0.000––
HISIDE_ISENSE_OC0.486––
HS_ADDR_SEL0.000––
HS_DUR_SEL0.027––
HS_GPIO0.687––
HS_TH_SEL0.042––
I2C_TCON_SCL_R0.483––
I2C_TCON_SDA_R0.483––
INLET_THMSNS_D1_N0.632––
INLET_THMSNS_D1_P0.634––
ISNS_1V5S3_IOUT0.618––
ISNS_HS_COMPUTING_IOUT0.600––
ISNS_HS_COMPUTING_N0.435––
ISNS_HS_COMPUTING_P0.435––
JTAG_ISP_TCK0.445––
KBDLED_SW0.364––
LED_RETURN_10.572––
LED_RETURN_20.572––
LED_RETURN_30.570––
LED_RETURN_40.568––
LED_RETURN_50.570––
LED_RETURN_60.567––
LPC_AD<0>0.442––
LPC_AD<1>0.441––
LPC_AD<2>0.442––
LPC_AD<3>0.441––
LPC_CLK33M_LPCPLUS0.476––
LPC_CLK33M_SMC0.450––
LPC_FRAME_L0.441––
LPC_PWRDWN_L0.460––
LPC_SERIRQ0.465––
LPCPLUS_GPIO0.490––
LPCPLUS_RESET_L0.393––
MEM_EVENT_L0.482––
P1V8S0_SW0.135––
P3V3S5_COMP20.626––
P3V3S5_CSN20.300––
P3V3S5_CSP20.521––
P3V3S5_CSP2_R0.300––
P3V3S5_DRVH0.758––
P3V3S5_DRVL0.512––
P3V3S5_EN_R0.415––
P3V3S5_LL0.300––
P3V3S5_PGOOD0.429––
P3V3S5_RF0.503––
P3V3S5_VBST0.550––
P3V3S5_VFB20.482––
P5V_S0_CPUIMVP_VDD0.360––
P5V3V3_REG_EN0.401––
P5VP3V3_VREF20.483––
P5VP3V3_VREG30.448––
P5VS3_COMP10.626––
P5VS3_CSN10.417––
P5VS3_CSP10.592––
P5VS3_DRVH0.863––
P5VS3_DRVL0.512––
P5VS3_EN_R0.429––
P5VS3_FUNC0.000––
P5VS3_LL0.416––
P5VS3_PGOOD0.426––
P5VS3_VBST0.551––
P5VS3_VFB10.487––
PBUS_S0_VSENSEOL––
PCA9557D_RESET_L0.386––
PCH_GPIO10_OC6_L0.517––
PCH_GPIO14_OC7_L0.514––
PCH_GPIO150.468––
PCH_GPIO350.465––
PCH_GPIO36_SATA2GP0.454––
PCH_GPIO43_OC4_L0.516––
PLT_RESET_L0.386––
PM_BATLOW_L0.457––
PM_CLKRUN_L0.476––
PM_DSW_PWRGD0.523––
PM_PECI_PWRGD_R0.428––
PM_PWRBTN_L0.435––
PM_SLP_S3_L0.451––
PM_SLP_S3_R_L0.474––
PM_SLP_S5_L0.457––
PM_SLP_SUS_L0.478––
PM_SUS_EN0.575––
PM_SYSRST_L0.466––
PM_THRMTRIP_L_R0.376––
PP1V05_S00.012––
PP1V5_S30.145––
PP1V5_S3RS00.051––
PP1V5_S3RS0_FET_R0.051––
PP1V05_SUS0.411––
PP1V8_S00.135––
PP3V3_S00.301––
PP3V3_S0_CPUTHMSNS_R0.310––
PP3V3_S30.342––
PP3V3_S50.290––
PP3V3_S5_AVREF_SMC0.470––
PP3V3_S5_SMC_AVCC0.288––
PP3V3_SUS0.373––
PP3V3_SW_LCD0.504––
PP3V42_G3H0.00––
PP5V_S00.358––
PP5V_S0_CPUVCCIOS0_VCC0.357––
PP5V_S0_VCCSAS0_VCC0.357––
PP5V_S30.418––
PP5V_S50.438––
PP5V1_CHGR_VDD0.414––
PP5V1_CHGR_VDDP0.414––
PPBUS_G3H0.435––
PPBUS_S5_HS_COMPUTING_ISNS0.444––
PPBUS_SW_LCDBKLT_PWR_SW0.398––
PPDCIN_G3H0.652––
PPVBAT_G3H_CHGR_REG0.435––
PPVCORE_S0_AXG_R0.007 1.7GHz i50.000––
PPVCORE_S0_CPU_PH10.008 1.7GHz i50.000––
PPVOUT_SW_LCDBKLT0.530––
PPVOUT_SW_LCDBKLT_FB0.534––
PVCCIO_S0_SMC_R0.012––
PVCCSA_EN0.474––
PVCCSA_PGOOD0.422––
S5_PWRGD0.402––
S5PGOOD_DLY0.400––
SATARDRVR_EN0.464––
SMBUS_PCH_CLK0.437––
SMBUS_PCH_DATA0.437––
SMBUS_SMC_0_S0_SCL0.473––
SMBUS_SMC_0_S0_SDA0.473––
SMBUS_SMC_A_S3_SCL0.451––
SMBUS_SMC_A_S3_SDA0.450––
SMBUS_SMC_B_S0_SCL0.439––
SMBUS_SMC_B_S0_SDA0.441––
SMBUS_SMC_BSA_SCL0.439––
SMBUS_SMC_BSA_SDA0.439––
SMBUS_SMC_MGMT_SCL0.462––
SMBUS_SMC_MGMT_SDA0.464––
SMC_1V5S3_ISENSE0.723––
SMC_ADAPTER_EN0.446––
SMC_BATLOW_L0.484––
SMC_BC_ACOK0.466––
SMC_BIL_BUTTON_L0.543––
SMC_BMON_ISENSE0.535––
SMC_BMON_MUX_SEL0.542––
SMC_CASE_OPEN0.475––
SMC_CLK32K0.454––
SMC_CPU_ISENSE0.718––
SMC_CPU_VSENSE0.650––
SMC_CPUVCCIO_ISENSE0.733––
SMC_DCIN_ISENSE0.727––
SMC_DCIN_VSENSE0.676––
SMC_DELAYED_PWRGD0.530––
SMC_DP_HPD_L0.507––
SMC_EXTAL0.731––
SMC_FAN_0_CTL0.533––
SMC_FAN_0_TACH0.527––
SMC_GFX_ISENSE0.718––
SMC_GFX_OVERTEMP_L0.542––
SMC_GFX_VSENSE0.650––
SMC_HDD_ISENSE0.545––
SMC_HDD_OOB_TEMP0.525––
SMC_HDD_TEMP_CTL0.533––
SMC_HS_COMPUTING_ISENSE0.532––
SMC_IG_THROTTLE_L0.501––
SMC_KBC_MDE0.730––
SMC_LCDBKLT_ISENSE0.540––
SMC_LID0.555––
SMC_LRESET_L0.392––
SMC_MANUAL_RST_L0.525––
SMC_MD10.718––
SMC_NMI0.718––
SMC_ONOFF_L0.503––
SMC_PB40.508––
SMC_PBUS_VSENSE0.493––
SMC_PM_G2_EN0.400––
SMC_PME_S4_WAKE_L0.530––
SMC_PROCHOT0.532––
SMC_PROCHOT_3_3_L0.486––
SMC_RESET_L0.405––
SMC_RUNTIME_SCI_L0.474––
SMC_RX_L0.484––
SMC_S4_WAKESRC_EN0.535––
SMC_SCI_L0.455––
SMC_SYS_KBDLED0.529––
SMC_TCK0.482––
SMC_TDI0.483––
SMC_TDO0.546––
SMC_THRMTRIP0.535––
SMC_TMS0.481––
SMC_TPAD_RST_L0.545––
SMC_TRST_L0.728––
SMC_TX_L0.487––
SMC_VCL0.355––
SMC_WLAN_ISENSE0.540––
SMC_XTAL0.711––
SMS_INT_L0.484––
SPI_ALT_CLK0.474––
SPI_ALT_CS_L0.468––
SPI_ALT_MISO0.00––
SPI_ALT_MOSI0.445––
SPI_DESCRIPTOR_OVERRIDE_L0.488––
SPI_MISO0.439––
SPI_MLB_CLK0.476––
SPI_MLB_CS_L0.470––
SPI_MLB_MISO0.437––
SPI_MLB_MOSI0.450––
SPI_MOSI0.445––
SPI_WP_L0.575––
SPIROM_USE_MLB0.460––
SYS_ONEWIRE0.4833.000–
T29_MLBBOT_THMSNS_N0.631––
T29_MLBBOT_THMSNS_P0.634––
T29THMSNS_ALERT_L0.666––
TP_XDP_PCH_TRST_LOL––
UNCONNECTED_1810.570––
UNCONNECTED_182OL––
UNCONNECTED_1830.447––
UNCONNECTED_1840.543––
UNCONNECTED_1850.996––
UNCONNECTED_4080.404––
USB_DEBUGPRT_EN_L0.461––
VCCSAS0_AGND0.000––
VCCSAS0_DRVH0.456––
VCCSAS0_DRVL0.405––
VCCSAS0_FSEL0.000––
VCCSAS0_LL0.035––
VCCSAS0_OCSET0.289––
VCCSAS0_RTN0.000––
VCCSAS0_SET00.474––
VCCSAS0_SET10.471––
VCCSAS0_SREF0.473––
VCCSAS0_VBST0.490––
VCCSAS0_VO0.289––
WIFI_EVENT_L0.486––
XDP_CPU_TDI0.033––
XDP_DBRESET_L0.466––
XDP_PCH_AUD_IPHS_SWITCH_EN0.459––
XDP_PCH_ENET_PWR_EN0.517––
XDP_PCH_GPIO59_OC0_L0.397––
XDP_PCH_ISOLATE_CPU_MEM_L0.471––
XDP_PCH_PWRBTN_L0.435––
XDP_PCH_S5_PWRGD0.627––
XDP_PCH_SDCONN_DET_L0.462––
XDP_PCH_SDCONN_STATE_RST_L0.455––
XDP_PCH_TCK0.019––
XDP_PCH_TDI0.423––
XDP_PCH_TDO0.411––
XDP_PCH_TMS0.422––
XDP_PCH_USB_HUB_SOFT_RST_L0.514––
XDPPCH_PLTRST_L0.566––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3023?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3023: diode 0.435. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3023?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3023: diode 0.00. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3023?

OpenBoardData's known-good values for PP5V_S5 on the 820-3023: diode 0.438. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3023 board?

Open your own 820-3023 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License