Apple laptop board · OpenBoardData

820-01124 known-good readings

Known-good readings for the Apple laptop board 820-01124: 54 nets, including 2 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 2 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01124.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 2 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 2

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.392––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V rail; the "G3S" suffix marks it as an always-on supply, from the name. The archive lists one known-good diode reading of 0.392, with no condition noted, and no known-good voltage reading here. Check it with the board unpowered in diode mode from PP1V8_G3S to ground, then measure the voltage with power applied. A diode reading far from 0.392 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PPBUS_G3H0.663––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H (820-01124) — reference note

  • What it is: the main bus rail that feeds the G3H (always-on) domain, inferred from the name; it is present whenever the board has power, before the main rails come up.
  • Known-good reading: diode 0.663 to ground, from the community archive (no condition recorded). No known-good voltage reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on PPBUS_G3H — compare with 0.663. Then power the board and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection or missing source. A single reading isn't proof — confirm with the voltage measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
AUD_CONN_HP_LEFT0.675––
AUD_CONN_HP_RIGHT0.660––
AUD_CONN_RING_SENSEOL––
AUD_CONN_RING20.002––
AUD_CONN_SLEEVE0.002––
AUD_CONN_TIP_SENSEOL––
AUD_PWR_ENOL––
AUD_RING_SENSE0.638––
CODEC_INT_L0.727––
CODEC_RESET_L0.728––
CODEC_WAKE_L0.722––
I2C_RIO_SCL0.409––
I2C_RIO_SDA0.408––
I2S_CODEC_BCLK0.590––
I2S_CODEC_D2R0.732––
I2S_CODEC_LRCLK0.696––
I2S_CODEC_R2D0.580––
I2S_SPKRAMP_L_D2R0.429––
I2S_SPKRAMP_R_BCLK0.413––
I2S_SPKRAMP_R_D2R_ROL––
I2S_SPKRAMP_R_LRCLK_R0.413––
I2S_SPKRAMP_R_R2D0.413––
L83_FILT0.780––
L83_HSBIAS_FILT0.720––
MESA_BOOST_EN_CONNOL––
MESA_INTOL––
MESA_INT_CONNOL––
MESA_MENUKEY_LOL––
MESA_PWR_EN0.571––
PMU_ONOFF_CONN_LOL––
PP1V8_G3S0.392––
PP1V8_MESA_CONN0.525––
PP1V8_SLPS2ROL––
PP3V0_MESA_CONN0.565––
PP16V0_MESA_CONN0.633––
PPBUS_G3H0.663––
SMC_LID_RIGHTOL––
SPI_MESA_CLKOL––
SPI_MESA_CLK_CONNOL––
SPI_MESA_MISOOL––
SPI_MESA_MISO_CONNOL––
SPI_MESA_MOSIOL––
SPI_MESA_MOSI_CONNOL––
SPKR_CONN_R_OUTN0.460––
SPKR_CONN_R_OUTP0.457––
SPKR_ID1OL––
SPKRAMP_INT_L0.413––
SPKRAMP_R_AREG0.552––
SPKRAMP_R_BSTN0.777––
SPKRAMP_R_BSTP0.777––
SPKRAMP_R_DREG0.543––
SPKRAMP_R_OUTN0.460––
SPKRAMP_R_OUTP0.457––
SPKRAMP_RESET_L0.415––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01124?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01124: diode 0.663. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01124 board?

Open your own 820-01124 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License