Apple laptop board · OpenBoardData

820-00923 known-good readings

Known-good readings for the Apple laptop board 820-00923: 390 nets, including 61 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 59 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00923.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 61 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 8

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V0_G3H–3.000–
AI: what PP3V0_G3H is and how to check it

PP3V0_G3H is a 3.0 V always-on rail on the 820-00923; the "G3H" suffix indicates it should be present whenever power is connected, from the rail name. The archive lists one known-good reading: 3.000 V, with no condition noted, so treat it as a guide. To check it, power off and measure diode mode from PP3V0_G3H to ground, then apply power and measure the voltage. No known-good diode reading is recorded here, so compare against a matching always-on rail or a known-good board. A voltage far below 3.000 V usually points to a short or a failed source, but that's a likely cause, not a confirmed one.

PP3V3_G3H0.3143.400–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail, judged from its name (G3H = always on). The archive lists a known-good diode reading of 0.314 to ground and a voltage of 3.400, with no condition noted, so treat both as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.314 usually points to a short or a leaky part on the rail; a voltage well off 3.400 points to a supply or loading fault. No known-good resistance reading exists here, so compare against a matching always-on rail or a known-good board.

PP3V3_G3H_SMC_ISNS–3.400–
AI: what PP3V3_G3H_SMC_ISNS is and how to check it
  • What it is: PP3V3_G3H_SMC_ISNS is a 3.3 V always-on rail, judged from its name: "PP3V3" is the 3.3 V supply, "G3H" is the always-on state, and "SMC_ISNS" suggests an SMC current-sense point on that rail. That reading of the name is general, not from board data.
  • Known-good reading: 3.400 V, with no condition recorded in the archive. There is no known-good diode or resistance value for this net here.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with a matching net or a known-good board, since no value is listed. Then apply power and measure the voltage at the net; it should sit near 3.400 V.
  • If it's far off: A voltage well below 3.400 V points to the always-on supply feeding it or a load pulling it down, not to a confirmed bad part. A near-short in diode mode suggests a shorted load on the rail. Confirm with a second measurement before replacing anything.
PPBUS_G3H0.46013.100–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the G3H suffix, from the name, marks it as an always-on rail. Known-good readings here are diode 0.460 and voltage 13.100, with no condition recorded, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.460 suggests a short or leaky load on the rail; a voltage far from 13.100 points to the charger or bus supply side. No known-good resistance reading is listed for this rail.

PPDCIN_G3H0.56120.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on DC input rail (the "G3H" suffix means always-on, from the name). Known-good readings here are diode 0.561 and voltage 20.000; no resistance value is listed. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.561 usually points to a short or a damaged component on the rail; a missing 20 V with power applied points upstream toward the input/charger side. These are community readings and a guide only, not a confirmed diagnosis.

PPDCIN_G3H_CHGR–20.000–
AI: what PPDCIN_G3H_CHGR is and how to check it
  • What it is: From the name, PPDCIN_G3H_CHGR is the charger-side DC input rail, in the G3H always-on domain — present whenever a charger is connected, before the board powers up.
  • Known-good reading: 20.000 V (voltage, from the readings archive). No known-good diode or resistance value is recorded for this rail.
  • How to check: With the board unpowered, diode mode from the rail to ground; then apply the charger and measure the voltage on the rail.
  • If it's far off: A missing or low voltage points to the charger input path (adapter, input connector, input-side components) rather than the rail itself; a short to ground in diode mode points to a fault on that rail. These are likely causes, not confirmed ones — verify with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R–13.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it
  • What it is: From the name, PPVBAT_G3H_CHGR_R is the battery/charger-side rail that is always on (G3H) in the charger section. It's a power rail, not a signal.
  • Known-good reading: The archive lists 13.100 V for this rail. No known-good diode or resistance reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from PPVBAT_G3H_CHGR_R to ground to look for a short. Then apply power and measure the voltage on the rail, comparing it with 13.100 V.
  • If it's far off: A very low diode reading suggests a short on the rail; a missing or low voltage points to the charger or its input path. These are likely causes, not confirmed ones — trace the rail before replacing anything.
PPVBAT_G3H_CHGR_REG0.32113.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From the name, PPVBAT_G3H_CHGR_REG is the charger-side regulated battery rail that stays present in the always-on G3H state. The exact parts on it aren't documented here.
  • Known-good readings (guide, from community data): diode 0.321 to ground, and 13.100 V with power applied.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If far off: A diode reading well below 0.321 suggests a short or leaky load on the rail; a missing or low voltage points to the charger circuit or its enable. No known-good resistance reading is available here, so compare against a matching rail or a known-good board before replacing anything.

S5 and SUS: standby 14

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_SUS_PCH_VCCCLK2_F–1.000–
AI: what PP1V_SUS_PCH_VCCCLK2_F is and how to check it
  • What it is: From its name, PP1V_SUS_PCH_VCCCLK2_F is a 1 V standby (SUS/S5) rail feeding the PCH clock domain. The name suggests it should be present in standby, before full power-on.
  • Known-good reading: The archive lists 1.000 V for this rail. No known-good diode or resistance reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground. Then apply power in standby and measure the voltage at the rail.
  • If it's off: A voltage far from 1.000 V in standby points to the rail's source or its enable being missing, or a heavy load on the rail. A low diode reading to ground suggests a shorted load, but one reading alone doesn't confirm a bad part; compare with a matching rail or a known-good board before replacing anything.
PP1V_SUS_PCH_VCCCLK4_F–1.000–
AI: what PP1V_SUS_PCH_VCCCLK4_F is and how to check it
  • What it is: From the name, a 1 V standby rail feeding the PCH clock (VCCCLK4) domain; the SUS/S5 naming marks it as a standby rail present before full power-on. This is general reading of the name, not from board data.
  • Known-good reading: The archive lists 1.000 V for this net. No known-good diode or resistance value here.
  • How to check: With the board unpowered, measure diode mode from the net to ground; then apply power and measure the voltage at the net.
  • If it's off: A voltage far from 1.000 V, or a near-short diode reading, usually points to a fault on that rail or its load — but a single reading doesn't confirm a bad part. Compare with a matching net or a known-good board before replacing anything.
PP1V_SUS_PCH_VCCCLK5_F–1.000–
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it
  • What it is: From its name, PP1V_SUS_PCH_VCCCLK5_F is a 1 V standby (SUS/S5) rail feeding the PCH clock area. The "1V" in the name matches the 1.000 V reading.
  • Known-good: The archive lists 1.000 V for this rail (startup stage S5/standby). No known-good diode or resistance reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's off: A voltage far from 1.000 V in standby points to the standby supply or an enable/load on that rail, but that's a likely cause, not a confirmed one. Compare diode readings against a matching rail or a known-good board before replacing anything.
PP1V_SUSSW_PCH_VCCAMPHYPLL_F–1.000–
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL_F is and how to check it
  • What it is: From the name, PP1V_SUSSW_PCH_VCCAMPHYPLL_F is a 1 V standby rail (SUS/S5) feeding the PCH's VCCAMPHYPLL supply. The name is the only description available here.
  • Known-good reading: 1.000 V, with no condition recorded. No known-good diode or resistance reading here.
  • How to check: Power off, then diode mode from the rail to ground. Power on and measure the voltage, comparing it with 1.000 V.
  • If it's far off: A short or low diode reading points to a fault on the rail or its load; no voltage at all points to the standby supply or enable side. Confirm with a second measurement before replacing anything.
PP1V0_SUS–1.000–
AI: what PP1V0_SUS is and how to check it
  • PP1V0_SUS is a 1.0 V standby rail, judged from its name (PP = power rail, 1V0 = 1.000 V, SUS = suspend/standby). The archive lists its nominal voltage as 1.000 V; no known-good diode or resistance reading is recorded for it here.
  • Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and in standby.
  • A voltage far from 1.000 V, or a near-short diode reading, usually points to a fault on the rail or its load, but one reading isn't proof. Compare against a known-good board of the same model before replacing anything.
PP1V0_SUSSW–1.000–
AI: what PP1V0_SUSSW is and how to check it
  • What it is: PP1V0_SUSSW is a 1.0 V standby rail, judged from its name (1V0 = 1.0 V, SUS = suspend/standby); it's a general naming convention, not confirmed from board data.
  • Known-good reading: the archive lists 1.000 V for this rail. There is no known-good diode or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V0_SUSSW to ground; then power up and measure the voltage, which should sit near 1.000 V.
  • If it's far off: a low or shorted diode reading points to a short on the rail, while a correct diode reading with missing voltage points upstream to its supply or enable. Compare against a matching standby rail on a known-good board, since no diode value is recorded here.
PP1V8_SUS–1.800–
AI: what PP1V8_SUS is and how to check it
  • What it is: PP1V8_SUS is a 1.8 V standby rail; the "SUS" in the name indicates it stays alive in standby, and the 1V8 indicates its nominal voltage.
  • Known-good reading: 1.800 V is the only archived value for this net. No known-good diode or resistance reading is available here.
  • How to check: With the board unpowered, measure diode mode from PP1V8_SUS to ground; then apply power and measure the voltage on the rail.
  • If it's off: A voltage far from 1.800 V, or a near-short in diode mode, usually points to a fault on the rail or its load rather than a confirmed bad part. Compare against a matching standby rail or a known-good board before replacing anything.
PP1V8_SUS_REG_R–1.800–
AI: what PP1V8_SUS_REG_R is and how to check it

PP1V8_SUS_REG_R is a 1.8 V standby rail; the "SUS" and "S5" in its name indicate it belongs to the standby stage, and "REG" suggests it comes from a regulator. The archive lists a known-good voltage of 1.800 V, but no diode or resistance reading for this net, so there is no known-good diode value here. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage at the rail. A voltage far from 1.800 V points to the standby regulator or its load rather than the rail itself, but that is a likely cause, not a confirmed one.

PP3V3_S50.3423.300–
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is a 3.3 V standby rail; the "S5" in the name marks it as a standby-stage supply (from the name, not from a schematic).
  • Known-good readings: diode 0.342 to ground and 3.300 V with power applied. These are community readings and a guide only; no known-good resistance value is listed.
  • How to check: power off and unplug, then measure diode mode from PP3V3_S5 to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.342 suggests a short or leaky load on the rail; no voltage or low voltage points to the standby supply not coming up. Confirm with a second measurement before replacing anything.
PP3V3_S5_SSD0.3653.300–
AI: what PP3V3_S5_SSD is and how to check it

PP3V3_S5_SSD — from the name, a 3.3 V standby rail (S5/SUS stage) feeding the SSD section. Known-good readings from the archive: diode 0.365 to ground, 3.300 V with power applied; no known-good resistance reading here.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. A far lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path.
  • Then apply power and measure the voltage: near 3.300 V is good, well below points to the rail not coming up or being loaded down.
  • These are community readings and vary with board state, so treat them as a guide; a small difference alone doesn't mean a part is bad.
PP3V3_S5_TBT_X_SW0.446––
AI: what PP3V3_S5_TBT_X_SW is and how to check it
  • What it is: PP3V3_S5_TBT_X_SW is a 3.3 V standby rail (the 3V3 and S5 come from the name) tied to the Thunderbolt side (TBT, from the name). The _SW suffix usually marks a switched rail, so it may only come up in certain states; that's general, not from this board's data.
  • Known-good reading: diode 0.446 in the archive, with no condition recorded. There is no known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with a voltage check before replacing anything.
PP3V3_SUS0.315––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is a 3.3 V standby rail; the SUS in the name marks it as a standby supply, and S5 puts it at the standby stage of startup. The only known-good figure here is a diode reading of 0.315 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.315 usually points to a short or a leaky part on the rail, but a single reading doesn't confirm a fault, so compare with the same rail on a known-good board before replacing anything.

PP5V_S5–5.000–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail; the S5/SUS part of the name marks it as a standby-stage supply, which is general naming convention rather than something confirmed for this board. The only archived reading is 5.000 V, with no condition recorded, and there is no known-good diode or resistance value for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage well below 5 V points to the standby supply not coming up or being loaded down, but with no known-good diode value here, compare against a matching net or a known-good board before condemning anything.

PPVCCPRIMCORE_SUS_PCH–1.000–
AI: what PPVCCPRIMCORE_SUS_PCH is and how to check it
  • What it is: From the name, PPVCCPRIMCORE_SUS_PCH is a standby ("SUS", S5 stage) core supply for the PCH. That's inferred from the rail name, not from board data.
  • Known-good reading: The archive lists 1.000 V for this rail. There is no known-good diode or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage at the rail. Compare the diode reading against a matching rail or a known-good board, since no reference value is listed.
  • If it's far off: A short or very low diode reading points to a fault on the rail or its load; a missing or wrong voltage with power applied points to the supply that generates it. Treat that as a lead, not a confirmed cause.

S4 10

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V8_S40.392––
AI: what PP1V8_S4 is and how to check it

PP1V8_S4 is a 1.8 V rail; the "S4" in the name marks it as a startup-stage rail (from the name, not from a schematic). The archive lists one known-good diode reading, 0.392, with no condition noted. With the board unpowered, measure diode mode from PP1V8_S4 to ground and compare with that figure; then apply power and check the rail sits near 1.8 V. No known-good voltage reading is recorded here, so treat 1.8 V as the name's nominal value rather than a measured reference. A diode reading far from 0.392, or a rail that won't come up, usually points to a short or a missing upstream supply, but that's a likely cause, not a confirmed one.

PP3V3_S40.3023.300–
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail for the S4 power state, judging by its name. In the readings archive its known-good readings are a diode of 0.302 to ground and 3.300 V with power applied; these are community values and only a guide.

  • Check it unpowered in diode mode from PP3V3_S4 to ground, then measure the voltage with the board powered.
  • A diode far below 0.302 suggests a short or a leaky load on the rail; a voltage well off 3.300 V points to the rail not coming up or being loaded down.
  • No known-good resistance reading exists for this rail here, so compare against a matching net or a known-good board.
PP3V3_S4_SOC_PMU0.328––
AI: what PP3V3_S4_SOC_PMU is and how to check it

PP3V3_S4_SOC_PMU is a 3.3 V rail feeding the SoC's PMU section, enabled at the S4 stage of the power sequence — that's from the name, not from board data.

  • Known-good: diode 0.328 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground, then power on and measure the voltage at the rail.
  • A diode reading far below 0.328 suggests a short or a leaky load on the rail; far above it suggests an open path. Confirm with a second measurement before suspecting a part.
PP3V3_S4_TPAD0.304––
AI: what PP3V3_S4_TPAD is and how to check it
  • What it is: PP3V3_S4_TPAD is a 3.3 V rail at the S4 power stage, from the name: the "TPAD" part suggests it feeds the trackpad section. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.304 to ground, from the community archive; treat it as a guide, not a spec.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or a heavy load on the rail, but one reading doesn't confirm a bad part. No known-good voltage reading is recorded here, so compare against a known-good board or the matching rail on the other side of a pair.
PP5V_S40.3905.000–
AI: what PP5V_S4 is and how to check it
  • What it is: PP5V_S4 is a 5 V rail in the S4 startup stage, both from its name. It's a switched supply that comes up partway through the power sequence, not a always-on rail.
  • Known-good readings (guide, from community contributions): diode 0.390 to ground, voltage 5.000 with power applied.
  • How to check: power off and unplug, then diode mode from PP5V_S4 to ground; expect around 0.390. Then power up and measure the voltage, expecting about 5.000 V.
  • If it's far off: a diode reading well below 0.390 suggests a short or leaky load on the rail; a missing or low voltage with a normal diode reading points upstream, to the rail's enable or its source supply. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PP5V_S4_T_USBC-0.1675.000–
AI: what PP5V_S4_T_USBC is and how to check it

PP5V_S4_T_USBC is a 5 V rail in the S4 startup stage, from its name. It's likely a USB-C-related 5 V supply, again from the name only.

  • Known-good readings in the archive: diode -0.167 to ground, voltage 5.000.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage.
  • A voltage well below 5.000 V or a diode reading far from -0.167 suggests the rail isn't coming up or something is loading it; a single reading isn't proof a part is bad.
  • No known-good resistance reading here, so compare against a matching net or a known-good board.
PP5V_S4_TPAD_CONN0.391––
AI: what PP5V_S4_TPAD_CONN is and how to check it
  • What it is: From its name, PP5V_S4_TPAD_CONN is a 5 V rail at the S4 startup stage feeding the trackpad connector. The board data only names the net and its stage; it doesn't list the parts on it.
  • Known-good reading: diode 0.391 to ground, no condition recorded. No known-good voltage reading here.
  • How to check: power off, then diode mode from PP5V_S4_TPAD_CONN to ground. Then power on and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.391 suggests a short or leaky part on the rail; a high or open reading suggests a broken connection. Treat 0.391 as a guide only, since readings vary with board state.
PP5V_S4_X_USBC0.1915.000–
AI: what PP5V_S4_X_USBC is and how to check it

PP5V_S4_X_USBC is a 5 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it. Known-good readings in the archive are diode 0.191 and voltage 5.000, with no condition noted, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 5.000 V points to the rail not coming up or being loaded down; a diode reading far from 0.191 suggests a short or an open on that net. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPBUS_S4_HS_TPAD–13.100–
AI: what PPBUS_S4_HS_TPAD is and how to check it

PPBUS_S4_HS_TPAD is a power rail on the 820-00923; the S4 in its name marks it as a startup-stage rail, and "HS_TPAD" suggests it feeds the trackpad side (that part is from the name, not confirmed by data).

  • Known-good reading here: 13.100 V. No known-good diode or resistance reading is recorded for this rail.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage, comparing it with 13.100 V.
  • A voltage far below known-good usually points to a short or heavy load on the rail or a missing upstream supply; a diode reading far off known-good on a matching rail or a known-good board suggests a shorted part on the net.
  • Treat the 13.100 V as a community guide, since readings vary with board state.
PPVIN_S4_TPAD_FUSE0.33313.100–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it
  • What it is: From the name, PPVIN_S4_TPAD_FUSE is a power-input rail in the S4 startup stage, feeding the trackpad section through a fuse. The board data doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.333 to ground, voltage 13.100. No known-good resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.333 suggests a short or a leaky part on the rail; no voltage or a low voltage with power applied points to the feed or fuse being open, or an upstream supply not coming up. Confirm with a second measurement before replacing anything.

S3: memory 4

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S30.2231.200–
AI: what PP1V2_S3 is and how to check it
  • What it is: PP1V2_S3 is a 1.2 V rail; the "S3" suffix places it in the memory stage of the startup sequence, from the name only.
  • Known-good readings: diode 0.223 to ground and 1.200 V with power applied (community archive, guide only, no condition recorded).
  • How to check: power off and unplug, then measure diode mode from PP1V2_S3 to ground; then power up and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail, while a missing or low voltage points to the rail not being enabled or its supply failing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning a part.
PP1V2_S3_REG_R0.2531.200–
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R is a 1.2 V S3 (memory-stage, from the name) regulator rail on the 820-00923. The archive gives a known-good diode reading of 0.253 to ground and 1.200 V with power applied; these are community readings and only a guide.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered.
  • A diode value far below 0.253 suggests a short or a leaky load on the rail; far above it suggests an open path.
  • A voltage well off 1.200 V points to the regulator or its feedback, not necessarily the rail itself.

No known-good resistance reading exists for this rail, so compare against a matching rail if one is available.

PP1V8_S3–1.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail in the S3 (memory) startup stage, judging from its name. The archive lists a known-good voltage of 1.800 V; there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far below 1.800 V usually points to a load pulling the rail down or a supply that isn't enabled; confirm with the diode reading before suspecting a part.

PP1V8_S3_MEM0.3651.800–
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM is the 1.8 V memory rail that comes up at the S3 stage of startup, judging from its name. The archive lists a known-good diode reading of 0.365 to ground and 1.800 V with power applied; treat these as a guide, since readings vary with board state. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode value far below 0.365 suggests a short or leaky part on the rail; a voltage well off 1.800 V points to the rail not being enabled or its supply failing. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board if needed.

S0: running 25

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.129––
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the "S0" in the name indicates it is present in the running state (from the name). The only known-good reading here is a diode value of 0.129 to ground, with no condition listed, and there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.129 usually points to a short or a leaky part on that rail, but a single reading is only a guide, so compare against a matching net or a known-good board before condemning anything.

PP1V8_S00.325––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail that is on in the running (S0) state, judged from its name. The archive lists one known-good diode reading to ground: 0.325, with no condition recorded. With the board unpowered, measure diode mode from PP1V8_S0 to ground and compare; then power up and check the voltage is about 1.8 V. No known-good voltage reading is recorded here. A diode value far from 0.325 usually points to a short or a damaged component on that rail, but one reading isn't proof, so confirm with the voltage and compare against a matching rail before replacing anything.

PP1V8_S0SW_DFR2.314 Burnt+Touchbar++Board+10.5420.555 Spare%2bunknown0.555 Spare+unknown0.111 Burnt%2bTouchbar%2b%2bBoard%2b11.810 Spare%2bunknown–
PP3V3_S00.275––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, so it should be present once the board is fully on. The only known-good reading in the archive is a diode value of 0.275 to ground, with no condition noted; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.275 usually suggests a short or a low-resistance load on the rail, while a much higher reading can point to an open connection; confirm with a voltage check before replacing anything.

PP3V3_S0_TBTTHMSNS_R0.292––
AI: what PP3V3_S0_TBTTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail tied to a Thunderbolt thermal-sense function; the exact parts on it aren't documented here.
  • Known-good reading: diode 0.292 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode to ground on the rail; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail, but one reading isn't proof — compare against a known-good board before replacing anything.
PP3V3_S0SW_DFR0.5663.300–
AI: what PP3V3_S0SW_DFR is and how to check it
  • What it is: From the name, PP3V3_S0SW_DFR is a 3.3 V rail that is switched (SW) and active in the S0 running state; the DFR suffix likely marks a specific load or function, but that isn't confirmed by the data.
  • Known-good readings: diode 0.566 and voltage 3.300. These come from community readings and are a guide only; no condition is recorded.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then apply power and measure the voltage.
  • If it's far off: a diode reading well below 0.566 suggests a short or leaky load on the rail; a missing 3.300 V with a normal diode reading points to the switch or its enable, not a short. These are likely causes, not confirmed ones.
PP3V3_TBT_T_S0–3.300–
AI: what PP3V3_TBT_T_S0 is and how to check it
  • What it is: From the name, PP3V3_TBT_T_S0 is a 3.3 V rail for the Thunderbolt section, active in S0 (running) state. The board data only names the net and its stage; it doesn't list which parts sit on it.
  • Known-good reading: 3.300 V, with the condition S0 (board running). No known-good diode or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from PP3V3_TBT_T_S0 to ground for a short indication, then power up into S0 and measure the voltage.
  • If it's far off: A missing or low 3.3 V in S0 points to the rail's supply or an enable upstream, not proof of a bad part. A near-zero diode reading to ground suggests a short on the rail. Compare against a matching rail or a known-good board where no value is listed.
PP5V_S00.435.1001.20R
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is up in the S0 (running) state, judged from its name. The archive lists diode 0.43, voltage 5.100 V and resistance 1.20R for it; these are community readings and only a guide, with no condition noted. Check it unpowered in diode mode from PP5V_S0 to ground, then power the board and measure the voltage. A diode or resistance far below the listed values suggests a short or a leaky load on the rail; a missing or low voltage with a normal diode reading points more toward the supply that creates it. No known-good waveform or current reading exists here.

PP5V_S0_ALSCAM_F0.43–1.20R
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V rail that, from its name, belongs to the S0 (running) state and feeds the camera circuit; the "_F" suffix usually marks a filtered or fused branch (general naming, not from board data). Known-good readings for this net are a diode drop of 0.43 and about 1.20R to ground, with the board unpowered. Check it in diode mode to ground first, then measure the voltage with the board powered and the rail enabled. A diode reading far below 0.43 or a resistance far below 1.20R points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part; there's no known-good voltage reading here, so compare against a matching rail or a known-good board.

PP5V_S0_BKLT_A–5.100–
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is a 5 V rail for the backlight circuit, enabled in the S0 (running) state — that reading comes from the name, not from a schematic. The archive lists one known-good figure: 5.100 V, with no condition noted. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and the display connected. No known-good diode reading is recorded here, so compare against a matching backlight rail or a known-good board. A voltage far from 5.100 V points to the backlight supply or its enable, not to the panel itself; confirm with a second measurement before replacing anything.

PP5V_S0_BKLT_D–5.100–
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is a 5 V backlight rail that is on in the S0 (running) state, judged from its name. The archive lists a known-good voltage of 5.100 V; there is no known-good diode or resistance reading for this net here.

  • Check it unpowered in diode mode from the net to ground, and compare with a matching 5 V S0 rail or a known-good board.
  • Then power the board and measure the voltage; it should sit near 5.1 V once the board is running.
  • A voltage far below 5.1 V points to the rail not coming up or being loaded down, but one reading doesn't confirm a bad part; trace the enable and supply side next.
PP5V_S0_FAN_CONN0.410––
AI: what PP5V_S0_FAN_CONN is and how to check it

PP5V_S0_FAN_CONN is a 5 V rail feeding the fan connector, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.410 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the connector. A diode reading far from 0.410 usually points to a short or a leaky part on that rail, but a single reading isn't proof, so compare against a known-good board before replacing anything.

PP5V_S0_KBD0.410––
AI: what PP5V_S0_KBD is and how to check it

PP5V_S0_KBD is a 5 V rail for the keyboard, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.410 to ground, with no condition noted; no known-good voltage is listed. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.410 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S0_T1390.465 Burnt+Touchbar++Board+10.466 Spare+unknown5.120 Burnt%2bTouchbar%2b%2bBoard%2b1–
PP5V_S0SW_LCD0.56––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is a switched 5 V rail for the LCD, and the S0 in its name indicates it belongs to the running state. The only known-good reading here is a diode value of 0.56 to ground; no voltage reading is recorded for this rail.

  • With the board unpowered, measure diode mode from PP5V_S0SW_LCD to ground and compare with 0.56.
  • Then power the board and confirm the rail comes up when the display should be active; there is no known-good voltage here to compare against.
  • A diode reading far from 0.56 usually points to a short or a leaky component on the rail, but a single reading isn't proof a part is bad.
PPVCC_S0_CPU–1.500–
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the "S0" in the name indicates it is active in the running state. The readings archive lists a known-good voltage of 1.500 V for this rail, but no diode or resistance value is recorded, so there is no known-good diode reading here. To check it, power the board off and measure diode mode from the rail to ground, then power up and measure the voltage at the rail. A voltage far from 1.500 V usually points to a problem in the rail's supply or its enable, not necessarily the CPU itself.

PPVCCEDRAM_S0_REG_F–1.050–
AI: what PPVCCEDRAM_S0_REG_F is and how to check it
  • What it is: PPVCCEDRAM_S0_REG_F is a supply rail for EDRAM, based on its name; the S0 suffix indicates it is active in the running state.
  • Known-good reading: 1.050 V, from the readings archive. This is a community value and a guide only; no known-good diode or resistance reading is available for this rail.
  • How to check: With the board unpowered, measure diode mode from the rail to ground. Then power the board and measure the voltage on the rail.
  • If it's far off: A large diode-mode difference or a missing or wrong voltage points to a problem on that rail or its source, but one reading alone doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.
PPVCCEDRAM_S0_REG_R0.1311.050–
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R is a switched DRAM supply rail; the S0 in the name indicates it is up in the running state, and the REG suggests it is a regulated rail (both from the name). The archive lists a known-good diode reading of 0.131 and a voltage of 1.050; no condition is recorded for either, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading well below 0.131 usually points to a short or a leaky part on the rail, while a voltage far from 1.050 with power applied points to the rail not regulating or not being enabled; there is no known-good resistance reading here, so compare against a matching rail or a known-good board.

PPVCCGT_S0_CPU–1.500–
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU is the CPU graphics rail; the "S0" in the name indicates it is up in the running state. The only known-good figure here is 1.500 V, with no condition recorded, and there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 1.500 V, or a diode reading very different from a matching rail on a known-good board, points to a problem in that rail's supply or load rather than confirming a bad part.

PPVCCIO_S0_CPU0.0170.950–
AI: what PPVCCIO_S0_CPU is and how to check it
  • What it is: PPVCCIO_S0_CPU is a CPU I/O supply rail; the "S0" in the name indicates it is up in the running state. The name is the only description available here.
  • Known-good readings (community archive, guide only): diode 0.017 to ground, voltage 0.950. No known-good resistance reading here.
  • How to check: with the board powered off, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a missing or wrong voltage with a normal diode reading points to the supply that feeds it or an enable signal. Confirm with a second measurement before replacing anything.
PPVCCSA_S0_CPU–1.500–
AI: what PPVCCSA_S0_CPU is and how to check it
  • What it is: From the name, PPVCCSA_S0_CPU is a CPU supply rail that is up in the S0 (running) state. The "VCCSA" part usually means the system-agent supply inside the CPU; that's general naming, not from this board's data.
  • Known-good reading: The archive lists a voltage of 1.500 for this rail. It has no known-good diode or resistance value, so there is nothing to compare those against here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground. Then apply power and measure the voltage, which should come up near 1.500 in S0.
  • If it's far off: A short or very low diode reading points to a fault on the rail or its load; no voltage in S0 points to the rail not being enabled or its supply missing. These are likely causes, not confirmed ones, so check the enable and upstream supply before replacing anything.
PPVIN_S0SW_LCDBKLT0.80513.100–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail switched in the S0 (running) state, judging by its name. The archive lists a diode reading of 0.805 and a voltage of 13.100; no condition is recorded for either, so treat them as a guide.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running.
  • A diode value well below 0.805 suggests a short or leaky load on the rail; a much higher one suggests an open path.
  • A voltage far from 13.100 with the board in S0 points to the supply or switch feeding the rail, not the backlight itself.
  • No known-good resistance reading exists for this rail.
PPVIN_S0SW_LCDBKLT_F–13.100–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F is the display backlight input rail; the name indicates an S0 (running-state) switched supply feeding the LCD backlight. The archive lists one known-good voltage of 13.100 V, with no condition recorded, and no known-good diode or resistance reading here. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A voltage far below 13.100 V points to the backlight supply or its enable not coming up, but that is a likely cause, not a confirmed one; compare the diode reading against a matching rail or a known-good board.

PPVIN_S0SW_LCDBKLT_R–13.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail; the name indicates an S0 (running-state) switched supply feeding the LCD backlight. The archive lists one known-good voltage of 13.100 V, with no condition noted, and no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far below 13.100 V points to the backlight supply or its enable not coming up rather than to the rail itself; a low diode reading to ground suggests a short on the rail. These are general checks, and the archive value is a community guide, not a confirmed specification.

PPVOUT_S0_LCDBKLT1.09055.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the name indicates a switched S0 (running-state) supply, and the VOUT/BKLT parts point to the backlight boost output. The archive lists a known-good diode reading of 1.090 and a voltage of 55.000, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 1.090 usually suggests a short or leaky load on the rail, while a voltage far from 55.000 with the display active points to the boost circuit not regulating or the rail not being enabled. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

Every net with a reading

NetDiodeVoltageResistance
8409_SPKR_ID00.736––
AMP_LT_I2C_SCL0.465––
AMP_LT_I2C_SDA0.470––
AMP_TL_LRCLK0.500––
AMP_TL_SCLK0.495––
AMP_TL_SDOUT0.330––
BUF_EDP_PANEL_PWR_EN0.56––
CPUCORE_ISNS1_N–1.500–
CPUCORE_ISNS1_P–1.500–
CPUCORE_ISNS2_N–1.500–
CPUCORE_ISNS2_P–1.500–
CPUCORE_SW10.0121.500–
CPUCORE_SW20.012––
CPUGT_ISNS1_N–1.500–
CPUGT_ISNS1_P–1.500–
CPUGT_ISNS2_N–1.500–
CPUGT_ISNS2_P–1.500–
CPUGT_ISNS3_N–1.500–
CPUGT_ISNS3_P–1.500–
CPUGT_SW10.0011.500–
CPUGT_SW20.0012.500–
CPUGT_SW30.0011.500–
CPUSA_ISNS_N–1.500–
CPUSA_ISNS_P–1.500–
CPUTHMSNS_D3_N0.666––
CPUTHMSNS_D3_P0.666––
CPUVR_SWSA0.012––
DFR_CLKIN_RESET_L0.492 Burnt+Touchbar++Board+10.520 Spare+unknown––
DFR_DISP_INT0.457––
DFR_DISP_RESET_L0.6951.800–
DFR_DISP_TE0.455––
DFR_DISP_VSYNC0.492 Burnt+Touchbar++Board+10.4480.516 Spare+unknown––
DFR_TOUCH_GPIO20.490 Burnt+Touchbar++Board+10.519 Spare+unknown––
DFR_TOUCH_INT_L0.498 Burnt+Touchbar++Board+10.529 Spare+unknown––
DFR_TOUCH_LID0.500 Burnt+Touchbar++Board+10.527 Spare+unknown––
DFR_TOUCH_PANEL_DETECT0.490 Burnt+Touchbar++Board+10.512 Spare+unknown––
DFR_TOUCH_RESET_L0.487 Burnt+Touchbar++Board+10.526 Spare+unknown––
DFR_TOUCH_ROM_I2C_SCL0.494 Burnt+Touchbar++Board+10.518 Spare+unknown––
DFR_TOUCH_ROM_I2C_SDA0.496 Burnt+Touchbar++Board+10.519 Spare+unknown––
DFR_TOUCH_ROM_WC0.489 Burnt+Touchbar++Board+10.520 Spare+unknown––
DFR_TOUCH_SPI_CLK_R0.487 Burnt+Touchbar++Board+10.527 Spare+unknown––
DFR_TOUCH_SPI_CS_L0.488 Burnt+Touchbar++Board+10.524 Spare+unknown––
DFR_TOUCH_SPI_MISO_R0.486 Burnt+Touchbar++Board+1OL Spare+unknown––
DFR_TOUCH_SPI_MOSI_R0.488 Burnt+Touchbar++Board+10.528 Spare+unknown––
DFRDRV_I2C_SCL0.4831.800–
DFRDRV_I2C_SDA0.4821.800–
DP_TB_AUXCH_N0.814––
DP_TB_AUXCH_P0.813––
DP_TB_HPD0.599––
DP_XB_AUXCH_N0.814––
DP_XB_HPD0.591––
EDP_INT_AUX_N0.21––
EDP_INT_AUX_P0.21––
FAN_LT_PWM0.872––
FAN_LT_TACHOL––
FAN_RT_PWM0.854––
I2C_TBT_T_SCL0.594––
I2C_TBT_T_SDA0.592––
I2C_TBT_TB_INT_L0.596––
I2C_TBT_X_SCL0.533––
I2C_TBT_X_SDA0.533––
I2C_TBT_XB_INT_L0.533––
I2C_UPC_T_SCL20.694––
I2C_UPC_T_SDA20.694––
I2C_UPC_TB_DBG_CTL_SCL0.774––
I2C_UPC_TB_DBG_CTL_SDA0.773––
I2C_UPC_XB_DBG_CTL_SCL0.775––
I2C_UPC_XB_DBG_CTL_SDA0.776––
ISNS_1V0_N–1.000–
ISNS_1V0_P–1.000–
ISNS_CPUDDR_N–1.200–
ISNS_CPUDDR_P–1.200–
ISNS_CPUEDRAM_N–1.050–
ISNS_CPUEDRAM_P–1.050–
ISNS_LCDBKLT_N–13.100–
ISNS_LCDBKLT_P–13.100–
ISNS_LPDDR_N–1.800–
ISNS_LPDDR_P–1.800–
ISNS_PCHPRIMCORE_N–1.000–
ISNS_PCHPRIMCORE_P–1.000–
ISNS_SSDNAND_N–2.700–
ISNS_SSDNAND_P–2.700–
KBD_BLC_GSLAT0.680––
KBD_BLC_GSSCK0.680––
KBD_BLC_GSSIN0.680––
KBD_BLC_GSSOUT0.488––
KBD_BLC_XBLANK0.677––
KBD_I2C_SCL0.536––
KBD_I2C_SDA0.412––
KBD_INT_L0.558––
LPSR_EN_LB_L–3.300–
MEM_A_CAB<9>0.192––
MEM_B_CAA<0>0.192––
MEM_B_CAA<1>0.192––
MEM_B_CAA<2>0.170––
MEM_B_CAA<3>0.192––
MEM_B_CAA<4>0.170––
MEM_B_CAA<5>0.192––
MEM_B_CAA<6>0.192––
MEM_B_CAA<7>0.192––
MEM_B_CAA<8>0.192––
MEM_B_CAA<9>0.192––
MEM_B_CAB<0>0.192––
MEM_B_CAB<1>0.192––
MEM_B_CAB<2>0.192––
MEM_B_CAB<3>0.192––
MEM_B_CAB<4>0.192––
MEM_B_CAB<5>0.192––
MEM_B_CAB<6>0.192––
MEM_B_CAB<7>0.192––
MEM_B_CAB<8>0.192––
MEM_B_CAB<9>0.192––
MEM_B_CKE<2>0.201––
MEM_B_CKE<3>0.201––
MEM_B_CLK_N<1>0.171––
MEM_B_CLK_P<1>0.171––
MEM_B_CS_L<0>0.200––
MEM_B_CS_L<1>0.200––
MEM_B_ODT<0>0.200––
MENU_KEY_L0.71––
MESA_BOOST_EN_CONN0.75––
MESA_I2C_SCL0.46––
MESA_I2C_SDA0.47––
MESA_SNSR_INT_CONN0.71––
MESA_SPI_CLK_CONN0.48––
MESA_SPI_MISO_CONN0.46––
MESA_SPI_MOSI_CONN0.46––
MIPID_CLK_CONN_N0.755––
MIPID_CLK_CONN_P0.745––
MIPID_DATA_CONN_N0.752––
MIPID_DATA_CONN_P0.745––
P0V9_FIXED_SW–0.900–
P0V9_REG_SW0–0.900–
P0V9_REG_SW1–0.900–
P1V0PCH_PHASE0.2651.000–
P1V0PCH_REG_R0.2651.000–
P1V2_HOT_SW–1.200–
P1V2_PHASE0.2531.200–
P1V8_COLD_SW0–1.800–
P1V8_COLD_SW1–1.800–
P1V8_HOT_SW–1.800–
P1V8SUS_SW–1.800–
P1VS4_PHASE0.2301.000–
P2V7NAND_R0.3572.700–
P2V7NAND_SW0.3572.700–
P3V3S5_CSN2–3.300–
P3V3S5_CSP2_R–3.300–
P3V3S5_EN–3.400–
P3V3S5_VSW0.3423.300–
P5VP3V3_VREG3–3.300–
P5VS4_CSN1–5.000–
P5VS4_CSP1_R–5.000–
P5VS4_VSW0.3905.000–
P5VS5_EN–3.400–
P5VUSBC_T_LL0.2085.000–
P5VUSBC_T_NEG–5.000–
P5VUSBC_T_POS–5.000–
P5VUSBC_T_R0.2085.000–
P5VUSBC_X_LL0.1955.000–
P5VUSBC_X_R0.1955.000–
PBUS_S0_VSENSE_IN–13.100–
PCH_INTRUDER_L–2.800–
PCH_SRTCRST_L–3.000–
PICCOLO_POK2–3.300–
PM_DSW_PWRGD–3.400–
PM_PWRBTN_L–3.300–
PM_RSMRST_L–3.300–
PM_SLP_S0_L–3.300–
PM_SLP_SUS_L–3.300–
PMIC_VINVR5–13.100–
PMU_ONOFF_L0.400––
PP0V6_S0_DDRVTT0.129––
PP0V6_SLEEP1_BUCK0–0.600–
PP0V8_SLEEP2_BUCK1–0.800–
PP0V9_SSD_FIXED–0.900–
PP0V9_SSD_REG–0.900–
PP0V9_TBT_T_SVR–0.900–
PP0V9_TBT_X_SVR–0.900–
PP1V_PCH_REG_R0.2301.000–
PP1V_SUS_PCH_VCCCLK2_F–1.000–
PP1V_SUS_PCH_VCCCLK4_F–1.000–
PP1V_SUS_PCH_VCCCLK5_F–1.000–
PP1V_SUSSW_PCH_VCCAMPHYPLL_F–1.000–
PP1V0_SUS–1.000–
PP1V0_SUSSW–1.000–
PP1V1_SLEEP3_BUCK2–1.100–
PP1V1_UPC_TA_LDO_BMC0.525––
PP1V1_UPC_TB_LDO_BMC0.521––
PP1V1_UPC_XA_LDO_BMC0.524––
PP1V1_UPC_XB_LDO_BMC0.4331.100–
PP1V2_S30.2231.200–
PP1V2_S3_REG_R0.2531.200–
PP1V2_SSD_COLD–1.200–
PP1V2_SSD_HOT–1.200–
PP1V8_MESA_CONN0.48––
PP1V8_S00.325––
PP1V8_S0SW_DFR2.314 Burnt+Touchbar++Board+10.5420.555 Spare%2bunknown0.555 Spare+unknown0.111 Burnt%2bTouchbar%2b%2bBoard%2b11.810 Spare%2bunknown–
PP1V8_S3–1.800–
PP1V8_S3_MEM0.3651.800–
PP1V8_S40.392––
PP1V8_SLEEP3_BUCK3–1.800–
PP1V8_SSD_COLD–1.800–
PP1V8_SSD_HOT–1.800–
PP1V8_SUS–1.800–
PP1V8_SUS_REG_R–1.800–
PP1V8_UPC_TA_LDOD0.497––
PP1V8_UPC_TB_LDOA0.514––
PP1V8_UPC_TB_LDOD0.493––
PP1V8_UPC_XA_LDOA0.533––
PP1V8_UPC_XA_LDOD0.497––
PP1V8_UPC_XB_LDOA0.4541.800–
PP1V8_UPC_XB_LDOD0.4251.800–
PP3V0_G3H–3.000–
PP3V0_MESA_CONN0.53––
PP3V3_2V7_NAND_VCC–2.700–
PP3V3_G3H0.3143.400–
PP3V3_G3H_SMC_ISNS–3.400–
PP3V3_S00.275––
PP3V3_S0_TBTTHMSNS_R0.292––
PP3V3_S0SW_DFR0.5663.300–
PP3V3_S40.3023.300–
PP3V3_S4_SOC_PMU0.328––
PP3V3_S4_TPAD0.304––
PP3V3_S50.3423.300–
PP3V3_S5_SSD0.3653.300–
PP3V3_S5_TBT_X_SW0.446––
PP3V3_SUS0.315––
PP3V3_TBT_T_F–3.300–
PP3V3_TBT_T_S0–3.300–
PP3V3_UPC_TA_LDO0.5203.300–
PP3V3_UPC_TB_LDO0.5183.300–
PP3V3_UPC_XA_LDO0.5183.300–
PP3V3_UPC_XB_LDO0.5083.300–
PP5V_S00.435.1001.20R
PP5V_S0_ALSCAM_F0.43–1.20R
PP5V_S0_BKLT_A–5.100–
PP5V_S0_BKLT_D–5.100–
PP5V_S0_FAN_CONN0.410––
PP5V_S0_KBD0.410––
PP5V_S0_T1390.465 Burnt+Touchbar++Board+10.466 Spare+unknown5.120 Burnt%2bTouchbar%2b%2bBoard%2b1–
PP5V_S0SW_LCD0.56––
PP5V_S40.3905.000–
PP5V_S4_T_USBC-0.1675.000–
PP5V_S4_TPAD_CONN0.391––
PP5V_S4_X_USBC0.1915.000–
PP5V_S5–5.000–
PP16V0_MESA_CONN0.62––
PP20V_USBC_TA_VBUS–20.000–
PP20V_USBC_TA_VBUS_CONN–20.000–
PP20V_USBC_TA_VBUS_F–20.000–
PP20V_USBC_TB_VBUS0.15320.000–
PP20V_USBC_TB_VBUS_CONN–20.000–
PP20V_USBC_TB_VBUS_F–20.000–
PP20V_USBC_XA_VBUS–20.000–
PP20V_USBC_XA_VBUS_CONN–20.000–
PP20V_USBC_XA_VBUS_F–20.000–
PP20V_USBC_XB_VBUS0.154–6.300k
PP20V_USBC_XB_VBUS_CONN0.020––
PPBUS_G3H0.46013.100–
PPBUS_HS_CPU–13.100–
PPBUS_HS_OTH3V3–13.100–
PPBUS_HS_OTH5V–13.100–
PPBUS_S4_HS_TPAD–13.100–
PPDCIN_G3H0.56120.000–
PPDCIN_G3H_CHGR–20.000–
PPDCPRTC_PCH–1.600–
PPVBAT_G3H_CHGR_R–13.100–
PPVBAT_G3H_CHGR_REG0.32113.100–
PPVCC_CPU_PH10.0121.500–
PPVCC_CPU_PH20.0121.500–
PPVCC_S0_CPU–1.500–
PPVCCEDRAM_PHASE0.1311.050–
PPVCCEDRAM_S0_REG_F–1.050–
PPVCCEDRAM_S0_REG_R0.1311.050–
PPVCCGT_CPU_PH10.0011.500–
PPVCCGT_CPU_PH20.0011.500–
PPVCCGT_CPU_PH30.0011.500–
PPVCCGT_S0_CPU–1.500–
PPVCCIO_S0_CPU0.0170.950–
PPVCCPRIMCORE_SUS_PCH–1.000–
PPVCCSA_CPU_R0.0121.500–
PPVCCSA_S0_CPU–1.500–
PPVIN_2V7NAND_LB0.4622.700–
PPVIN_S0SW_LCDBKLT0.80513.100–
PPVIN_S0SW_LCDBKLT_F–13.100–
PPVIN_S0SW_LCDBKLT_R–13.100–
PPVIN_S4_TPAD_FUSE0.33313.100–
PPVIN_SW_LCDBKLT_SW0.80513.100–
PPVOUT_S0_LCDBKLT1.09055.000–
PVCCIO_PHASE0.1230.950–
RTC_RESET_L–3.000–
S3X_I2C_SDA–1.800–
SMBUS_SMC_3_SCL0.496––
SMBUS_SMC_3_SDA0.492––
SMC_ACTUATOR_DISABLE_L0.708––
SMC_ADAPTER_EN–3.400–
SMC_LID1.797––
SMC_LID_LEFT–3.400–
SMC_LSOC_RST_L0.717––
SMC_ONOFF_L–3.400–
SMC_PM_G2_EN–3.400–
SMC_PME_S4_WAKE_L0.708––
SMC_USBC_INT_L0.648––
SMC_VIBE_L0.698––
SOC_PMU_BUCK0_LX–0.600–
SOC_PMU_BUCK1_LX–0.800–
SOC_PMU_BUCK2_LX–1.100–
SOC_PMU_BUCK3_LX–1.800–
SOC_SWD_LS_EN0.453––
SPI_MLB_CLK0.565––
SPI_MLB_IO0_MOSI0.510––
SPI_MLB_IO1_MISO0.505––
SPI_MLB_IO2_WP_L0.505––
SPI_MLB_IO3_HOLD_L0.505––
SPI_MLBROM_CS_L0.630––
SPKRAMP_BSTP_1OL––
SPKRAMP_BSTP_2OL––
SPKRAMP_LT_I2C_ADDROL––
SPKRAMP_TL_OUT_NOL––
SPKRAMP_TL_OUT_POL––
SPKRCONN_TL_OUT_N0.560––
SPKRCONN_TL_OUT_P0.555––
SPRAMP_5V_TLOL––
SSD_DBG_UART_D2R–3.300–
SSD_DBG_UART_D2R_R–3.300–
STORAGE_LB_EN–3.300–
TBA_CSI_N–20.000–
TBA_CSI_P–20.000–
TBA_CSI_R_N–20.000–
TBA_CSI_R_P–20.000–
TBA_CSO_N–13.100–
TBA_CSO_P–13.100–
TBA_CSO_R_N–13.100–
TBA_CSO_R_P–13.100–
TBA_PHASE10.39613,100–
TBA_PHASE20,39613,100–
TBT_TB_LSRX0.599––
TBT_TB_LSTX0.599––
TBT_X_ROM_HOLD_L0.704––
TBT_X_ROM_WP_L0.597––
TBT_X_SPI_CLK0.576––
TBT_X_SPI_CLK_DBG0.675––
TBT_X_SPI_CS_L0.603––
TBT_X_SPI_MISO0.607––
TBT_X_SPI_MOSI0.600––
TBT_XB_LSRX0.593––
TBTTHMSNS_ALERT_L0.534––
TBTTHMSNS_D1_N0.000––
TBTTHMSNS_D1_P0.588––
TBTTHMSNS_THM_L0.558––
TPAD_SPI_CLK_R0.541––
TPAD_SPI_CS_CONN_R_L0.715––
TPAD_SPI_IF_EN_CONN0.655––
TPAD_SPI_INT_CONN_L0.646––
TPAD_SPI_MISO_R0.530––
TPAD_SPI_MOSI_R0.541––
UPC_TA_UART_RX0.759––
UPC_TA_UART_TX0.759––
UPC_TB_DBG_UART_RX0.772––
UPC_TB_DBG_UART_TX0.775––
UPC_TB_DBG30.774––
UPC_TB_DBG40.771––
UPC_TB_GATE10.667––
UPC_TB_GATE20.650––
UPC_TB_R_OSC0.512––
UPC_TB_SS0.512––
UPC_X_SPI_CLK0.575––
UPC_X_SPI_CS_L0.595––
UPC_X_SPI_MISO0.598––
UPC_X_SPI_MOSI0.600––
UPC_XA_UART_TX0.761––
UPC_XB_DBG_UART_RX0.772––
UPC_XB_R_OSC0.513––
UPC_XB_SPI_CLK0.590––
UPC_XB_SPI_CS_L0.617––
UPC_XB_SPI_MISO0.622––
UPC_XB_SPI_MOSI0.624––
USB_CAMERA_DFR_N1.241.24 Webcam - no screen––
USB_CAMERA_DFR_P1.191.19 Webcam - no screen––
USB_UPC_TB_F_N0.575––
USB_UPC_XB_F_N0.575––
USB_UPC_XB_F_P0.573––
USBC_TB_CC10.608––
USBC_TB_CC20.614––
USBC_TB_SBU10.843––
USBC_TB_SBU20.849––
USBC_XB_CC10.606––
USBC_XB_CC20.612––
VR0V9_IND_TBT_T–0.900–
VR0V9_IND_TBT_X–0.900–

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00923?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00923: diode 0.460, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00923?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00923: diode 0.314, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00923?

OpenBoardData's known-good values for PP5V_S5 on the 820-00923: voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00923 board?

Open your own 820-00923 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License