Apple laptop board · OpenBoardData

820-3437 known-good readings

Known-good readings for the Apple laptop board 820-3437: 551 nets, including 74 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 74 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3437.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 74 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.3203.40–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on the 820-3437, judged from its G3H suffix (G3H = always on). Known-good readings in the archive: diode 0.320 to ground and 3.40 V with power applied. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.320 suggests a short or leaky load on the rail; a voltage well under 3.40 V with a normal diode reading points to the supply or its enable, not a short. No known-good resistance reading exists here, so compare against a matching always-on rail or a known-good board.

PP3V42_G3H_SMC_SPVSR0.3080––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is an always-on 3.42 V rail feeding the SMC's SPVSR input, judged from the name (G3H = always on). The archive lists one known-good diode reading of 0.3080 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from the net to ground and compare with 0.3080; then power up and check the voltage is present. A diode reading far from 0.3080 usually points to a short or open on that net, but a single reading doesn't confirm a bad part.

PPBUS_G3H0.1658.500–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the always-on main power bus on this board, as its G3H name indicates. The archive lists a known-good diode reading of 0.165 to ground and a voltage of 8.500, both as community guides with no condition noted.

  • Check it unpowered in diode mode from PPBUS_G3H to ground; compare with 0.165.
  • Then power the board and measure the voltage on PPBUS_G3H; compare with 8.500.

No known-good resistance reading is listed here. A diode value far below 0.165 suggests a short or a leaky part on the rail; a voltage well off 8.500 points to the rail not coming up or being loaded down, but one reading alone doesn't confirm a bad part.

PPBUS_G3H_R0.170––
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main battery-charging bus on this board; the G3H suffix, from the name, marks it as an always-on rail. The archive lists a diode reading of 0.170 to ground for it, with no condition noted, so treat that as a guide only. With the board unpowered, measure diode mode from the rail to ground and compare; then apply power and check the DC voltage. A diode reading far below 0.170 usually suggests a short or a leaky component on the rail, while a much higher one can point to an open path. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board.

PPDCIN_G3HOL––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, as its name indicates — on this board it's the DC-in feed that should be present whenever the charger is connected. The only known-good reading in the archive is a diode value of OL to ground, with no condition noted; there is no known-good voltage or resistance reading here. Check it unpowered in diode mode from the rail to ground, then with the charger connected measure the DC voltage on it. A diode reading well below OL suggests a short or leaky path on that rail; a missing or low voltage with the charger attached points upstream to the DC-in input, adapter sensing or a protection component rather than the rail itself. These are general checks, and the OL figure is a community guide, not a confirmed spec.

PPDCIN_G3H_CHGR0.626––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in its name indicates it is always-on whenever the charger is connected. The archive lists a known-good diode reading of 0.626 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with the charger connected. No known-good voltage reading is available here, so compare against a known-good board or the matching charger input net. A diode reading far from 0.626 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part.

PPDCIN_G3H_INRUSH0.626––
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is a startup-stage rail; the G3H in its name indicates it is always-on, present whenever the adapter is connected. The archive lists a diode reading of 0.626 for this net, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the net to ground, then measure its voltage with the adapter connected. No known-good voltage reading is listed here, so compare against a matching net or a known-good board. A diode reading far from 0.626 usually points to a short or open on that net, but one reading alone doesn't confirm a bad part.

PPDCIN_G3H_ISOLOL––
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is an always-on (G3H, from the name) DC-input rail on the 820-3437 — the isolated DC-in feed, typically from the charger/MagSafe side before it is switched further into the board. That's general naming, not from this board's data.

  • Known-good: the only archived reading is diode mode to ground, OL (open). No known-good voltage reading here.
  • Check it: power off and unplug, then diode mode from the rail to ground; then apply power and measure DC volts on the rail.
  • If a diode reading is far from OL (a low reading to ground), suspect a short or leaky part on that rail; a voltage far from the expected DC-in level points to the input path or charger side. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R0.165––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name indicates it is always on whenever power is present. The only known-good reading here is a diode value of 0.165 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. A diode reading far from 0.165 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPVBAT_G3H_CHGR_REG0.1658.500–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side battery rail; the G3H in the name indicates it is always-on, and CHGR points to the charger circuit (from the name). Known-good readings here are diode 0.165 and voltage 8.500. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good resistance reading is recorded here. A reading far from these usually points to a short or open on the rail or its charger source, but that is a likely cause, not a confirmed one.

PPVBAT_G3H_CONNOL––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judged from its name; on this board it's the main battery power input. The only archived reading is a diode value of OL to ground, with no condition noted, and there's no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then with the battery or adapter connected measure the DC voltage on it. A diode reading far below OL, or a short to ground, usually points to a fault on that rail or a part hanging off it; OL alone doesn't prove the rail is good.

PPVIN_G3H_P3V42G3H0.39415.38–
AI: what PPVIN_G3H_P3V42G3H is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V42G3H is the always-on G3H input rail feeding the 3V42 regulator stage on the 820-3437. It is present whenever the board has input power.
  • Known-good readings (community archive, guide only): diode 0.394 to ground, and 15.38 V with power applied.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below known-good suggests a short or leaky load on the rail; no or low voltage with power applied points to a missing input supply or an open path feeding the rail. No known-good resistance reading is listed for this rail.
PPVRTC_G3H0.43423.40–
AI: what PPVRTC_G3H is and how to check it
  • What it is: PPVRTC_G3H is the always-on RTC rail; the G3H suffix means "always on," from the name. It should be present whenever the board has standby power.
  • Known-good readings (community guide): diode 0.4342 to ground, and 3.40 V with power applied.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.4342. Then apply power and measure the voltage, expecting about 3.40 V.
  • If it's off: a diode reading far from 0.4342 suggests a short or a leaky part on the rail; no voltage with power applied points to the supply or an open path feeding it. These are likely causes, not confirmed ones, so trace the feed before replacing anything.

S5 and SUS: standby 12

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.517––
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: PP1V2_S5_SMC_VDDC is a 1.2 V rail, from its name, tied to the SMC supply and present in the S5 standby state (from its name).
  • Known-good reading: diode 0.517 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing or wrong voltage points to the supply that generates it. Confirm with a second measurement before replacing anything.
PP1V05_SUS0.295––
AI: what PP1V05_SUS is and how to check it

PP1V05_SUS is a 1.05 V standby rail; the name indicates it is a suspend/standby supply (from the name, not from board data). The only known-good reading here is a diode value of 0.295 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading exists here. A diode reading far from 0.295 usually points to a short or a faulty part on that rail, but confirm with a second measurement before replacing anything.

PP3V3_S50.35413.30–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the S5/SUS suffix in its name marks it as a standby-stage supply. Known-good readings in the archive are a diode value of 0.3541 and 3.30 V, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading well below known-good usually points to a short or leaky load on the rail; a missing or low voltage points to the standby supply or its enable. No known-good resistance reading is recorded here, so compare against a matching standby rail or a known-good board.

PP3V3_S5_AVREF_SMC0.5952––
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC is a 3.3 V standby rail (S5) that, from its name, also serves as an analog reference for the SMC. The only known-good reading here is a diode value of 0.5952 to ground, with the board unpowered; no known-good voltage reading is listed. Check it by measuring diode mode from the net to ground with power off, then measure the DC voltage on the net with the board powered in standby. A diode reading far from 0.5952 usually points to a short or a leaky component on that net, but a single reading isn't proof of a bad part, so compare against a matching net or a known-good board before replacing anything.

PP3V3_S5_REG_R0.361–320.000R
AI: what PP3V3_S5_REG_R is and how to check it

PP3V3_S5_REG_R is a 3.3 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, and this is from the name only. Known-good readings in the archive: diode 0.361 and resistance 320.000R, with no stated condition, so treat them as a guide. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. No known-good voltage reading here, so compare against a matching rail or a known-good board. A reading far from known-good usually points to a short or leak on the rail or its load, but one reading doesn't confirm a bad part; check the supply side and the load side before replacing anything.

PP3V3_S5_SMC_VDDA0.320––
AI: what PP3V3_S5_SMC_VDDA is and how to check it
  • What it is: From the name, PP3V3_S5_SMC_VDDA is a 3.3 V standby (S5/SUS) rail feeding the SMC's analog supply (VDDA). It sits in the standby startup stage.
  • Known-good reading: Diode mode to ground, board unpowered: 0.320. This is a community value and a guide only; there is no known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below known-good often suggests a short or leaky part on the rail; a high or open reading can mean a broken trace or missing part. Confirm with a voltage check before replacing anything.
PP3V3_S5RS3RS0_SYSCLKGEN0.35393.30–
AI: what PP3V3_S5RS3RS0_SYSCLKGEN is and how to check it

PP3V3_S5RS3RS0_SYSCLKGEN is a 3.3 V standby rail, from its name: the S5/SUS part marks it as a standby supply, and the SYSCLKGEN part suggests it feeds system clock generation. The archive lists a known-good diode reading of 0.3539 to ground and a known-good voltage of 3.30, with no condition noted, so treat both as a guide.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.3539.
  • Then power the board and measure the voltage; it should sit near 3.30.
  • A diode reading far below known-good usually points to a short or a failing part on the rail; a voltage well off 3.30 points to the standby supply not coming up or being loaded down.

No known-good resistance reading is available here, so a resistance check can only be compared against a matching rail or a known-good board.

PP3V3_SUS0.350––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail; the "SUS" in the name indicates it stays up in standby (from the name). The archive lists a known-good diode reading of 0.350 to ground for this rail, with no condition noted. To check it, power the board off and measure diode mode from PP3V3_SUS to ground, then apply power and measure the voltage. A diode reading far from 0.350 usually points to a short or a damaged load on the rail, but a single reading isn't proof, so compare against a matching net or a known-good board. No known-good voltage reading is listed here.

PP3V3_SUS_FET_R0.350––
AI: what PP3V3_SUS_FET_R is and how to check it

PP3V3_SUS_FET_R is a standby rail on the 820-3437; the "SUS" and S5 in its name indicate it belongs to the suspend/standby stage, and the "FET_R" suffix suggests a switched branch, though that part is general interpretation, not from board data. The only known-good reading here is a diode value of 0.350 to ground; no known-good voltage reading is recorded for this rail. Check it with the board unpowered in diode mode, red probe on the rail and black to ground, then measure the voltage with power applied. A diode reading far from 0.350 usually points to a short or a leaky component on that net, but a single reading isn't proof a part is bad.

PP5V_S50.455.00–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the board fully powers on. Known-good readings in the archive: diode 0.45 to ground and 5.00 V with power applied.

  • Check it unpowered in diode mode from PP5V_S5 to ground; expect around 0.45.
  • Then apply power and measure the voltage; expect about 5.00 V.
  • A diode reading far below 0.45 suggests a short or leaky load on the rail; far above suggests an open path.
  • No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

These are community readings and only a guide; confirm with a second measurement before replacing anything.

PPBUS_S5_HS_COMPUTING_ISNS0.1648.60–
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it

PPBUS_S5_HS_COMPUTING_ISNS (820-3437) — the name indicates a PPBUS sense line in the S5/SUS standby stage, tied to the high-side computing supply.

  • Known-good readings from the archive: diode 0.164 to ground, voltage 8.60 V. These are community values and only a guide; no known-good resistance reading here.
  • Check with the board unpowered in diode mode from the net to ground, then power up and measure the voltage.
  • A diode reading far below 0.164 suggests a short or leaky part on the net; a voltage well off 8.60 V points to a supply or sense-circuit fault. Confirm with a second measurement before replacing anything.
PPBUS_S5_HS_OTHER_ISNS0.1658.60–
AI: what PPBUS_S5_HS_OTHER_ISNS is and how to check it
  • What it is: From the name, PPBUS_S5_HS_OTHER_ISNS is a PPBUS rail in the S5 standby domain, with "ISNS" suggesting a current-sense related node. The board data only gives the name and stage, not which parts sit on it.
  • Known-good readings (community guide): diode 0.165 to ground, and 8.60 V with power applied. No known-good resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground; then apply power and measure the voltage.
  • If far off: A diode reading well below 0.165 suggests a short or leaky load on the rail; a missing or low voltage points to the rail not coming up in standby. Confirm with a second measurement before replacing anything.

S4 9

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.38993.300–
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging from its name (S4 is a sleep-state rail, general knowledge, not from this board's data). The archive lists a known-good diode reading of 0.3899 and a voltage of 3.300; no condition is recorded for either. Check it with the board unpowered in diode mode from PP3V3_S4 to ground, then power up and measure the voltage. A diode reading far below 0.3899 usually points to a short or a leaky part on the rail, while a missing 3.300 V with a normal diode reading points upstream to the rail's enable or source. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP3V3_S4_FET_R0.395––
AI: what PP3V3_S4_FET_R is and how to check it

PP3V3_S4_FET_R is a 3.3 V rail in the S4 power state, judged from its name; the FET suffix suggests it sits after a switching FET. The archive lists one known-good diode reading of 0.395 to ground, with no condition noted, and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.395 usually points to a short or a leaky part on that rail, but one reading isn't proof a part is bad.

PP3V3_S4_IPD0.38––
AI: what PP3V3_S4_IPD is and how to check it

PP3V3_S4_IPD (820-3437) — reference note

  • What it is: a 3.3 V rail in the S4 startup stage, judged from the name (PP = power rail, 3V3 = 3.3 V, S4 = sleep-state stage). What it feeds isn't known from the available data.
  • Known-good reading: diode mode to ground, 0.38. That is the only known-good value recorded here; there is no known-good voltage or resistance reading for this rail.
  • How to check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.38. Then apply power and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing load on the rail; a much higher one to an open path. A single reading doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.
PP3V3_S4_TBTAPWR0.36––
AI: what PP3V3_S4_TBTAPWR is and how to check it

PP3V3_S4_TBTAPWR is a 3.3 V rail, judging from its name, and the S4 in the name puts it in the S4 startup stage. The only known-good reading here is a diode value of 0.36 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.36 usually points to a short or a damaged part on that net, but a small difference can be normal, so compare with a matching rail or a known-good board before replacing anything.

PP3V3RHV_S4_TBTAPWR0.55––
AI: what PP3V3RHV_S4_TBTAPWR is and how to check it

PP3V3RHV_S4_TBTAPWR is a 3.3 V rail in the S4 startup stage, judging by its name (the "TBTAPWR" part suggests it feeds Thunderbolt power circuitry, but that's general reading of the name, not from board data). The only known-good reading here is a diode value of 0.55; no known-good voltage or resistance is recorded.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail. Compare with 0.55.
  • Then power the board and measure the DC voltage on the rail.

A diode reading far below 0.55 usually points to a short or a leaky load on the rail; a much higher or open reading suggests a broken trace or missing connection. A missing voltage with a normal diode reading points more toward the rail not being enabled or its source not running. These are likely causes, not confirmed ones, and community readings vary with board state, so treat 0.55 as a guide.

PP3V3RHV_S4_TBTAPWR_F0.550––
AI: what PP3V3RHV_S4_TBTAPWR_F is and how to check it
  • What it is: From its name, PP3V3RHV_S4_TBTAPWR_F is a 3.3 V rail in the S4 startup stage, likely the Thunderbolt/display power feed (TBTAPWR). The exact parts on it aren't known here.
  • Known-good reading: diode 0.550 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.550. Then power on and measure the voltage; it should sit near 3.3 V.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; an open or high reading points to a missing feed or broken trace. Confirm with a second measurement before replacing anything.
PP5V_S4_IPD0.4374––
AI: what PP5V_S4_IPD is and how to check it

PP5V_S4_IPD is a 5 V rail in the S4 startup stage, judging from its name (general naming, not from board data). The only known-good reading here is a diode value of 0.4374 to ground; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.4374 usually points to a short or a leaky load on the rail, but one reading isn't proof a part is bad.

PP5V_S4RS30.4355.00–
AI: what PP5V_S4RS3 is and how to check it

PP5V_S4RS3 is a 5 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it. Known-good readings here are a diode value of 0.435 to ground and 5.00 V with power applied, both from community contributions and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.435 suggests a short or leaky load on the rail; a voltage well off 5.00 V points to the rail not coming up or being pulled down. No known-good resistance reading is listed for this rail.

PPVIN_S4SW_TBTBST_FET0.537––
AI: what PPVIN_S4SW_TBTBST_FET is and how to check it

PPVIN_S4SW_TBTBST_FET — reference note

  • From its name, this is a switched S4-stage power input rail feeding the Thunderbolt boost-converter FET. It is a power rail, not a signal.
  • Known-good reading in the archive: diode mode to ground 0.537. No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.537. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.537 usually points to a short or a leaky part on the rail; far above it suggests an open path. A single reading isn't proof a part is bad, so confirm with a voltage check under power.

S3: memory 13

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S30.1401.20–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail in the S3 (memory) startup stage, based on its name; the board data doesn't list which parts sit on it.

  • Known-good readings from the archive: diode 0.140 to ground, voltage 1.20. These are community values and only a guide.
  • Check with the board unpowered: multimeter in diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.140 suggests a short or a failing load on the rail; far above it suggests an open connection. Confirm with a second reading before replacing anything.
  • No known-good resistance reading is listed here.
PP1V8_S30.393––
AI: what PP1V8_S3 is and how to check it
  • What it is: PP1V8_S3 is a 1.8 V rail in the S3 (memory) startup stage, judged from its name; the exact parts it feeds aren't known here.
  • Known-good reading: diode 0.393 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V8_S3 to ground and compare with 0.393; then power up and measure the rail voltage.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; a much higher one suggests an open path. A single reading isn't proof, so confirm before replacing anything.
PP1V8_S3_REG_R0.393––
AI: what PP1V8_S3_REG_R is and how to check it

PP1V8_S3_REG_R is a 1.8 V S3 (memory-stage) regulated rail, judged from its name; the board data doesn't list which parts sit on it. The only known-good reading here is diode mode to ground, 0.393, with no condition given. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading exists here, so compare against a matching rail on a known-good board. A diode reading far below 0.393 usually suggests a short or a failing load on the rail, but one reading doesn't confirm a bad part; verify with a second measurement before replacing anything.

PP3V3_S30.487––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that, judging by its name, comes up at the S3 (memory) stage of the startup sequence. The only known-good figure here is a diode reading of 0.487 to ground, with no condition noted; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power the board and measure the voltage. A diode value far from 0.487 usually points to a short or a damaged component on that rail, but a small difference can be normal, so compare with a matching rail or a known-good board before condemning anything.

PP3V3_S3_FET_R0.487––
AI: what PP3V3_S3_FET_R is and how to check it

PP3V3_S3_FET_R is a 3.3 V S3 (memory-stage) rail; the "FET_R" suffix suggests it's the FET-switched side, from the name only, not confirmed by board data. The only known-good reading here is diode 0.487 to ground, with no condition given and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.487 usually points to a short or leaky load on the rail, but one reading isn't proof, so compare against a matching rail before replacing anything.

PP3V3_S3RS0_CAMERA0.359––
AI: what PP3V3_S3RS0_CAMERA is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA is a 3.3 V rail in the S3 (memory/suspend) power stage, judged from the name; the "CAMERA" suffix suggests it feeds camera circuitry. This comes from the name only, not from board data.
  • Known-good reading: diode 0.359 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.359; then power up and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing voltage points upstream to the S3 supply and enable. Confirm with a second measurement before replacing anything.
PP3V3_S3RS0_CAMERA_R0.359––
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it
  • What it is: From the name, PP3V3_S3RS0_CAMERA_R is a 3.3 V rail that comes up at the S3 (memory) startup stage and feeds camera circuitry. The exact parts on it aren't known here.
  • Known-good reading: diode 0.359 in diode mode to ground, board unpowered. No known-good voltage reading is available.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.359; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading suggests a shorted load on the rail; a missing voltage with a normal diode reading points upstream to the rail's enable or supply. Confirm with a second measurement before replacing anything.
PP5V_S3_RTUSB_A_F0.493––
AI: what PP5V_S3_RTUSB_A_F is and how to check it

PP5V_S3_RTUSB_A_F is a 5 V rail that, from its name, is switched in the S3 (memory/suspend) power state and feeds a USB-A circuit. The archive lists one known-good diode reading of 0.493, with no condition noted; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board in S3. A diode reading far below 0.493 usually points to a short or a leaky load on the rail; a far higher or open reading suggests a broken trace or missing connection. Treat the single figure as a guide only, since readings vary with board state.

PP5V_S3_RTUSB_A_ILIM0.493––
AI: what PP5V_S3_RTUSB_A_ILIM is and how to check it

PP5V_S3_RTUSB_A_ILIM is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state and feeds the USB-A current-limit circuit. The only known-good reading in the archive is a diode value of 0.493 to ground; there is no known-good voltage or resistance reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.493 usually points to a short or leaky component on that net, but a single reading doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PP5V_S3_U62100.433––
AI: what PP5V_S3_U6210 is and how to check it

PP5V_S3_U6210 is a 5 V rail in the S3 (memory) startup stage, judging by its name; the U6210 suffix points to the regulator that produces it. The only known-good reading here is a diode value of 0.433 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.433 usually points to a short or a failing load on the rail, while a far higher or open reading points to a broken connection or a dead regulator. Treat the value as a community guide, not a confirmed spec.

PP5V_S3RS0_ALSCAM_F0.4039––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it

PP5V_S3RS0_ALSCAM_F is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) startup stage and feeds the camera circuit. The only known-good figure here is a diode reading of 0.4039 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below that value usually points to a short or a failing load on the rail, while a correct diode reading with no voltage points back to the rail's source or its enable. These are community readings and only a guide, so compare against a matching rail or a known-good board before condemning a part.

PPDDR_S3_REG_R0.140––
AI: what PPDDR_S3_REG_R is and how to check it
  • What it is: From the name, PPDDR_S3_REG_R is an S3-stage memory rail (DDR supply/regulator) on the 820-3437.
  • Known-good reading: diode 0.140 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.140; then power up and measure the rail voltage.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on that rail, but one reading isn't proof. Confirm with the voltage measurement before replacing anything.
PPVTT_S3_DDR_BUF0.4900.60–
AI: what PPVTT_S3_DDR_BUF is and how to check it
  • What it is: From the name, PPVTT_S3_DDR_BUF is a memory (S3) termination/buffer rail for DDR — a small reference/termination supply, not a main rail.
  • Known-good readings (community archive, guide only): diode 0.490 to ground, voltage 0.60. No known-good resistance is listed here.
  • How to check: Power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing or wrong voltage points to its source or enable. Confirm with a second measurement before replacing anything.

S0: running 27

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.1820.60–
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT — from the name, a 0.6 V rail that is a DDR termination voltage, active in the S0 (running) state.

  • Known-good readings from the archive: diode 0.182 to ground, and 0.60 V with power applied. These are community values and a guide only; the data gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 0.182. Then power up and measure the voltage, expecting about 0.60 V.
  • A diode reading far below 0.182 suggests a short or a leaky part on the rail; far above suggests an open path. A voltage well off 0.60 V while in S0 points at the rail's regulator or its enable, not the termination loads.
  • No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP1V05_S00.1311.00–
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail that is active in the S0 (running) state, judged from its name. In the readings archive its known-good values are a diode reading of 0.131 to ground and about 1.00 V with the board powered in S0; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage in S0. A diode reading far below 0.131 suggests a short or a failing load on the rail, while a correct diode reading with missing or low voltage points upstream at the rail's supply or enable. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP1V5_S0–1.50–
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.50 V rail; the "S0" suffix, from the name, marks it as a running-state supply. The archive lists its known-good voltage as 1.50 V, but no diode or resistance reading is recorded for it. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well off 1.50 V points to a fault on that rail or its source rather than to the load, but with no known-good diode value here, compare against a matching rail or a known-good board before condemning anything.

PP1V05_S0_REG_R0.131–151.000R
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V rail; the "S0" in the name marks it as a running-state supply, and "REG_R" suggests a regulated rail on the right side of the board (from the name). Known-good readings in the archive: diode 0.131 and resistance 151.000R — treat these as a guide only, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far below known-good usually points to a short or a leaky part on that rail; a far higher one can mean an open path. There is no known-good voltage value here, so compare against a matching rail or a known-good board.

PP1V5_S0SW_AUDIO0.36751.50–
AI: what PP1V5_S0SW_AUDIO is and how to check it

PP1V5_S0SW_AUDIO is a 1.5 V audio rail; the "S0" in its name indicates it is active in the running (S0) state, and "SW" suggests a switched rail. Known-good readings from the archive: diode 0.3675 to ground and 1.50 V with power applied. To check it, power off and measure diode mode from the rail to ground, then power on and measure the voltage. A diode reading far from 0.3675 usually points to a short or a leaky part on that rail; a voltage well below 1.50 V with power on suggests the rail isn't being enabled or is loaded down. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.

PP3V3_S00.60 Backlight driver off0.35233.30–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judging from its name. Known-good readings here are a diode of 0.60 with the backlight driver off, a diode of 0.3523, and 3.30 V with power applied; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 3.30 V points to a load or short pulling the rail down, while a diode far from the known values suggests a shorted or open path on that net; no known-good resistance reading is listed here.

PP3V3_S0_CPUTHMSNS_R0.406––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R is a 3.3 V rail in the S0 (running) state, judging by its name; the "CPUTHMSNS" part suggests it feeds CPU thermal sensing, but that's from the name only. The archive lists one known-good diode reading of 0.406 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on the net and black on ground, then measure the voltage with the board powered and running. A diode reading far from 0.406 usually points to a short or a damaged component on that net, but one reading isn't proof. No known-good voltage reading is recorded here, so compare against a matching net or a known-good board.

PP3V3_S0_FET_R0.352––
AI: what PP3V3_S0_FET_R is and how to check it

PP3V3_S0_FET_R is a 3.3 V rail; the S0 in the name indicates it belongs to the running state, and the FET_R suffix suggests a switched feed, though that part is inference from the name rather than board data. The only known-good reading here is a diode value of 0.352 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and in S0. No known-good voltage reading is available for this rail, so compare against a matching rail or a known-good board. A diode reading far from 0.352 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S0SW_LCD0.631––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a switched 3.3 V LCD rail; the S0 in the name indicates the running state, and SW suggests it is switched on rather than always present. The archive lists one known-good diode reading of 0.631, with no condition given and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.631 points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0SW_LCD_R0.631––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is a switched 3.3 V LCD rail; the S0 part of the name indicates it belongs to the running state, and SW suggests it is switched on rather than always present (from the name, not from board data). The only known-good figure here is a diode reading of 0.631 to ground with the board unpowered; there is no known-good voltage reading for this rail. Check it in diode mode with power off, then measure the voltage with the board powered and the display active. A diode reading far from 0.631 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S0SW_LCD_UF0.5873––
AI: what PP3V3_S0SW_LCD_UF is and how to check it

PP3V3_S0SW_LCD_UF is a 3.3 V LCD-related rail, switched and enabled in the running (S0) state, judging from the name. The archive lists one known-good diode reading of 0.5873 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.5873 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S0SW_SSD0.563––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a 3.3 V rail that, from its name, is switched (SW) and active in the S0 running state, feeding the SSD section. The only known-good reading here is a diode value of 0.563 to ground; no voltage or resistance readings are recorded for this rail. Check it with the board unpowered in diode mode, red probe on the rail and black to ground, then power up and measure the voltage. A diode reading far below 0.563 usually points to a short or leaky part on the rail, while a much higher or open reading suggests a broken connection or missing part; confirm with a voltage check before replacing anything.

PP3V3_S0SW_SSD_FET_R0.563––
AI: what PP3V3_S0SW_SSD_FET_R is and how to check it
  • What it is: From its name, PP3V3_S0SW_SSD_FET_R is a 3.3 V rail that is switched (SW) through a FET and enabled in the S0 (running) state, feeding the SSD. The exact parts on the net aren't known here.
  • Known-good reading: diode 0.563 to ground, from the readings archive (community value, a guide only). No known-good voltage reading is available here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage, which should be present only in S0.
  • If it's far off: a much lower diode reading usually points to a short or a failing component on the rail; a missing voltage points to the FET, its enable signal, or the upstream 3.3 V source. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_SSD_FLT0.55––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a switched 3.3 V rail for the SSD, from its name: S0 means it comes up in the running state, and SW suggests it is switched on rather than always present. The readings archive lists one known-good diode value of 0.55 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.55 usually points to a short or a leaky part on that rail, but a single reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S01.51 Backlight driver off0.430––
AI: what PP5V_S0 is and how to check it

PP5V_S0 — the name indicates a 5 V rail that is present in the S0 (running) state.

  • Known-good readings from the archive: diode 1.51 with the backlight driver off, and diode 0.430. These are community readings and only a guide; the state of the board matters.
  • To check it: power off and unplug, then measure diode mode from PP5V_S0 to ground. Then apply power and measure the voltage on the rail.
  • No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A diode reading far from these values usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.
PP5V_S0_ALT_AUD_LDO_ENOL––
AI: what PP5V_S0_ALT_AUD_LDO_EN is and how to check it

PP5V_S0_ALT_AUD_LDO_EN is an enable signal for an audio LDO rail, judged from its name; the S0 part suggests it belongs to the running state. The only known-good reading here is a diode reading of OL to ground, with no condition recorded; there is no known-good voltage reading for this net. Check it unpowered in diode mode from the net to ground, then measure its voltage with the board powered in S0. A diode reading far from OL (a low value) usually points to a short or a leaky part on that net, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PP5V_S0_CPUVR_VDD0.430––
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD is a 5 V rail that, from its name, supplies the CPU voltage regulator and is present in the S0 (running) state. The only known-good figure here is a diode reading of 0.430 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.430 usually suggests a short or leaky part on the rail; a far higher or open reading suggests a broken connection. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP5V_S0_FET_R0.430––
AI: what PP5V_S0_FET_R is and how to check it

PP5V_S0_FET_R is a 5 V rail that, from its name, is switched through a FET and belongs to the S0 (running) power state. The archive lists one known-good diode reading of 0.430 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S0. A diode reading far below 0.430 usually points to a short or leaky part on that rail, while a much higher reading can mean an open path; treat these as guides, not confirmed faults.

PPHV_S0SW_LCDBKLT0.608––
AI: what PPHV_S0SW_LCDBKLT is and how to check it

PPHV_S0SW_LCDBKLT is the LCD backlight boost rail; the name indicates it's a running-state (S0) high-voltage backlight switch node. The archive lists one known-good diode reading of 0.608 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then confirm the boosted voltage with power applied and the display connected. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.608 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PPVCC_S0_CPU0.0421.800147.000
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — reference note (820-3437)

  • What it is: the CPU core power rail, active in the S0 (running) state, as the name indicates. It's the main VCORE supply the CPU needs once the board is out of standby.
  • Known-good readings (community guide): diode 0.042 to ground, resistance 147.000, and 1.800 V with the board powered and running. These vary with board state, so treat them as a guide, not a spec.
  • How to check: power off and unplug, then measure diode mode (and resistance) from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a shorted or very low diode/resistance reading points to a shorted load on the rail (often the CPU or its supply), while correct diode but missing voltage points upstream to the rail's regulator and its enable. No known-good value exists here for current draw or ripple.
PPVCC_S0_CPU_PH10.0421.80063.47R 1.3GHz 4GB82.25R 1.4GHz 4GB49.00R 1.7GHz 8GB147.000
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 is a CPU power rail; the S0 in its name indicates it is active in the running state. Known-good readings from the archive: diode 0.042 to ground, voltage 1.800, and resistance varying by CPU spec — 63.47R (1.3GHz 4GB), 82.25R (1.4GHz 4GB), 49.00R (1.7GHz 8GB), and 147.000 (condition not stated). Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from these usually points to a short or open on the rail or its load, but treat these as a guide only; no known-good value exists for some conditions here.

PPVCC_S0_CPU_PH20.0421.80063.33R 1.3GHz 4GB82.53R 1.4GHz 4GB49.92R 1.7GHz 8GB147.000
AI: what PPVCC_S0_CPU_PH2 is and how to check it

PPVCC_S0_CPU_PH2 is a CPU power rail; the S0 in the name indicates it belongs to the running (S0) state, and the PH2 suffix suggests a phase of the CPU VRM output (general interpretation, not from board data). Known-good readings here: diode 0.042 to ground, about 1.800 V when running, and resistance readings that vary by CPU spec — 63.33R (1.3GHz 4GB), 82.53R (1.4GHz 4GB), 49.92R (1.7GHz 8GB) and 147.000. These are community figures and only a guide; the spread shows the resistance depends on the fitted CPU, so compare against the matching variant. Check with the board unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far from 0.042 usually points to a short or a damaged phase component, but confirm with a second measurement before replacing anything.

PPVIN_S0_CPUVR_VIN0.174––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is, from its name, the input supply to the CPU voltage regulator, active in the S0 (running) state. The archive lists a known-good diode reading of 0.174 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the same net. A diode reading far from 0.174 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPVIN_S0SW_LCDBKLT0.427––
AI: what PPVIN_S0SW_LCDBKLT is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT is the switched input supply for the LCD backlight, active in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.427 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the net to ground; then apply power and measure the voltage on the net.
  • If it's far off: a diode reading well below known-good usually points to a short or a leaky part on the rail; a voltage that's missing or low points upstream in the backlight supply. These are general guidelines, not confirmed causes.
PPVIN_S0SW_LCDBKLT_FET0.43––
AI: what PPVIN_S0SW_LCDBKLT_FET is and how to check it

PPVIN_S0SW_LCDBKLT_FET is the switched input feed for the LCD backlight, from its name: an S0 (running-state) rail gated by a FET. The only known-good reading recorded is a diode value of 0.43 to ground, with no condition noted. With the board unpowered, measure diode mode from this net to ground and compare against 0.43; then power up and check the voltage on the net. No known-good voltage reading is recorded here, so compare the powered voltage against the rail feeding the FET and against a known-good board. A diode reading far below 0.43 usually points to a short or leaky part on the net, while a much higher or open reading suggests a broken connection or a FET that isn't switching.

PPVIN_S0SW_LCDBKLTFET0.166––
AI: what PPVIN_S0SW_LCDBKLTFET is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLTFET is the switched input rail feeding the LCD backlight FET, active in the S0 (running) state. It's a power rail, not a signal.
  • Known-good reading: diode 0.166 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with voltage under power before replacing anything.
PPVMEMIO_S0_CPU0.140––
AI: what PPVMEMIO_S0_CPU is and how to check it

PPVMEMIO_S0_CPU is a memory I/O rail; the S0 in the name indicates it's up in the running state (from the name, not from board data). The archive lists one known-good diode reading of 0.140 to ground, with no condition noted and no known-good voltage reading. Check it unpowered in diode mode to ground, then measure its voltage with the board powered. A diode reading far from 0.140 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault; compare against a matching rail or a known-good board before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD–3.30–
AP_CLKREQ_Q_L0.463.250–
AP_CLKREQ_R_L0.42––
AP_PCIE_WAKE_L0.52193.316–
AP_RESET_CONN_L0.46353.324–
AP_RESET_CONN_R_L0.45––
AP_RESET_L0.42––
AP_S0IX_WAKE_L0.435––
AP_S0IX_WAKE_SEL0.440––
AUD_PWR_EN0.6326––
BKL_ENOL Backlight driver off––
BKL_FAULTOL Backlight driver off0.56––
BKL_FLTROL Backlight driver off0.560––
BKL_FSETOL Backlight driver off0.500––
BKL_ISEN1OL Backlight driver off0.600––
BKL_ISEN2OL Backlight driver off0.640––
BKL_ISEN3OL Backlight driver off0.640––
BKL_ISEN4OL Backlight driver off0.640––
BKL_ISEN5OL Backlight driver off0.640––
BKL_ISEN6OL Backlight driver off0.640––
BKL_ISETOL Backlight driver off0.500––
BKL_PWM1.24 Backlight driver off0.500––
BKL_SCL0.90 Backlight driver off0.510––
BKL_SDA0.90 Backlight driver off0.500––
BKL_VSYNC_ROL Backlight driver off0.560––
BKLT_PLT_RST_L0.54––
BT_WAKE0.787––
CAM_SENSOR_WAKE_L_CONN0.0004––
CHGR_ACIN0.52624.10–
CHGR_AGATE0.64360.00–
CHGR_AGATE_DIVOL––
CHGR_AMON0.72090.20–
CHGR_BGATE0.66341.00–
CHGR_BMON0.72730.05–
CHGR_BOOT0.573713.00–
CHGR_CELL0.08340.00–
CHGR_CSI_N0.63615.7721.500R
CHGR_CSI_P0.62415.7721.500R
CHGR_CSI_R_N0.626––
CHGR_CSI_R_P0.626––
CHGR_CSO_N0.1658.604.000R
CHGR_CSO_P0.1658.604.000R
CHGR_CSO_R_N0.165––
CHGR_CSO_R_P0.165––
CHGR_DCIN0.620815.30–
CHGR_ICOMP0.72791.70–
CHGR_LGATE0.45562.00–
CHGR_PHASE0.1658.500–
CHGR_RST_L0.49923.30–
CHGR_SGATE0.64090.18–
CHGR_UGATE0.593711.00–
CHGR_VCOMP0.72601.40–
CHGR_VFRQ0.47270.00–
CHGR_VNEG0.52521.40–
CPU_PECI_R0.336––
CPU_PROCHOT_L0.193––
CPU_RTN0.002––
CPU_THRMTRIP_3V30.751––
CPU_VCCSENSE_N0.002––
CPU_VCCSENSE_P0.041––
CPU_VCCSENSE_P_R0.041––
CPU_VCCSENSE_P_RC1.553––
CPU_VIDSCLK0.185––
CPU_VIDSOUT0.196––
CPU_VR_EN0.335––
CPU_VR_READY0.551––
CPUBMONSNS_ALERT_L0.764––
CPUTHMSNS_ADDR_SEL0.000––
CPUTHMSNS_ALERT_L0.595––
CPUTHMSNS_D2_N0.755––
CPUTHMSNS_D2_P0.755––
CPUTHMSNS_DUR_SEL0.774––
CPUTHMSNS_TH_SEL0.774––
CPUVR_BOOT2–6.30–
CPUVR_COMP0.594––
CPUVR_COMP_RCOL––
CPUVR_DRSEL0.000––
CPUVR_FB0.554––
CPUVR_FB_RCOL––
CPUVR_FB20.578––
CPUVR_FCCM–5.00–
CPUVR_ISEN10.606––
CPUVR_ISEN20.600––
CPUVR_ISNS1_N0.0421.800147.000
CPUVR_ISNS1_P0.0421.800147.000
CPUVR_ISNS2_N0.0421.800147.000
CPUVR_ISNS2_P0.0421.800147.000
CPUVR_ISUM_IOUT0.641––
CPUVR_ISUM_R_N0.791––
CPUVR_ISUM_R_P0.791––
CPUVR_ISUMN0.041––
CPUVR_ISUMN_R0.297––
CPUVR_ISUMN_RC0.891––
CPUVR_ISUMP0.487––
CPUVR_LGATE2–3.80–
CPUVR_NTC0.604––
CPUVR_PHASE10.0421.80063.47R 1.3GHz 4GB82.25R 1.4GHz 4GB49.00R 1.7GHz 8GB147.000R
CPUVR_PHASE20.0421.8063.33R 1.3GHz 4GB82.52R 1.4GHz 4GB49.93R 1.7GHz 8GB147.000R
CPUVR_PROG20.595––
CPUVR_PROG30.603––
CPUVR_PWM10.593––
CPUVR_PWM2–0.00–
CPUVR_SLOPE0.597––
CPUVR_UGATE2–2.70–
DCIN_ISOL_GATE0.785––
DCIN_ISOL_GATE_ROL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.477––
DDRREG_1V8_VREF–1.80–
DDRREG_DRVH0.641.40–
DDRREG_DRVL0.461.40–
DDRREG_EN–3.30–
DDRREG_FB–1.20–
DDRREG_LL0.151.20–
DDRREG_MODE0.5330.00–
DDRREG_PGOOD0.5023.30–
DDRREG_TRIP0.7540.52–
DDRREG_VBST0.6266.20–
DDRREG_VBST_RC0.625––
DDRREG_VDDQSNS0.1511.20–
DDRREG_VTTSNS0.1820.60–
DP_INT_AUX_CH_C_NOL––
DP_INT_AUX_CH_C_POL––
DP_INT_HPD_CONN0.7880––
DP_INT_ML_N<0>OL––
DP_INT_ML_P<0>OL––
EDP_BKLT_EN0.697––
EDP_BKLT_PWM0.560––
FAN_RT_PWM0.79––
FAN_RT_TACH0.61––
FINSTACKSNS_ALERT_L0.5869––
GND0.0004––
GND_BKL_SGND0.00 Backlight driver off––
GND_P5VP3V3_SGND0.000.00–
GND_SMC_AVSS0.0005––
HDA_BIT_CLK0.4443––
HDA_RST_L0.4469––
HDA_SDIN00.4086––
HDA_SDOUT0.4454––
HDA_SYNC0.4453––
I2C_CAM_SCK0.7468––
I2C_CAM_SDA0.7467––
I2C_TCON_SCL_R0.7347––
I2C_TCON_SDA_R0.7306––
INLET_THMSNS_D1_N0.75––
INLET_THMSNS_D1_P0.75––
ISNS_1V2_S3_N0.140––
ISNS_1V2_S3_P0.140––
ISNS_1V05_S0_NOL––
ISNS_1V05_S0_POL––
ISNS_AIRPORT_N0.508––
ISNS_AIRPORT_P0.508––
ISNS_CAMERA_NOL––
ISNS_CAMERA_POL––
ISNS_CPUDDR_NOL––
ISNS_CPUDDR_POL––
ISNS_HS_COMPUTING_IOUT0.712––
ISNS_HS_COMPUTING_N0.165––
ISNS_HS_COMPUTING_P0.165––
ISNS_HS_OTHER_NOL––
ISNS_HS_OTHER_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_NOL––
ISNS_LCDBKLT_POL––
ISNS_P3V3_S0_NOL––
ISNS_P3V3_S0_POL––
ISNS_P5VSSD_IOUT0.712––
ISNS_PANEL_IOUTOL––
ISNS_SSD_N0.563––
ISNS_SSD_P0.563––
JTAG_TBT_TMS0.541––
KBDLED_SW0.430––
LCDBKLT_BOOST3.18 Backlight driver off0.427––
LCDBKLT_DISABLE0.500––
LCDBKLT_EN_DIV_LOL––
LCDBKLT_EN_L0.763––
LED_RETURN_10.6231––
LED_RETURN_20.6231––
LED_RETURN_30.6230––
LED_RETURN_40.6207––
LED_RETURN_50.6213––
LED_RETURN_60.6220––
LPC_AD<0>0.5413––
LPC_AD<1>0.5391––
LPC_AD<2>0.5386––
LPC_AD<3>0.5390––
LPC_CLK24M_LPCPLUS0.4613––
LPC_CLK24M_SMC0.478––
LPC_FRAME_L0.5353––
LPC_PWRDWN_L0.6104––
LPC_SERIRQ0.5354––
LPCPLUS_RESET_L0.5458––
MAX98300_R_N0.611––
MAX98300_R_P0.612––
MEM_EVENT_L0.752––
MEMVTT_PWR_EN–3.20–
MIPI_CLK_CONN_N0.4128––
MIPI_CLK_CONN_P3.0021––
MIPI_DATA_CONN_N0.4090––
MIPI_DATA_CONN_P0.4105––
P1V2_CAM_SRVLXC_PHASE0.276––
P1V05_S0_VREFOL1.80–
P1V05S0_AGND0.00040.00–
P1V05S0_DRVH3.47251.60–
P1V05S0_DRVH_R–1.60–
P1V05S0_DRVL0.46134.30–
P1V05S0_EN0.45173.30–
P1V05S0_FB0.66771.00–
P1V05S0_LL0.1311.00151.000R
P1V05S0_MODE0.51540.00–
P1V05S0_PGOOD0.48223.30–
P1V05S0_TRIP0.73590.18–
P1V05S0_VBST0.59416.00–
P1V05S0_VDDQSNS0.12811.00–
P1V05S0_VTT0.58620.50–
P1V05S0_VTTREF0.47980.50–
P1V5S0SW_AUDIO_EN–3.30–
P1V05S3_EN0.48360.00–
P1V8S3_EN–3.30–
P1V8S3_FB–0.80–
P1V8S3_PGOOD–3.30–
P1V8S3_SW–1.80–
P1V35_CAM_SRVLXD_PHASE0.247––
P3V3_S5_COMP20.741.96–
P3V3_S5_COMP2_ROL––
P3V3_S5_CSN20.353.30–
P3V3_S5_CSP21.323.30–
P3V3_S5_CSP2_R0.360––
P3V3_S5_DRVH0.893.90–
P3V3_S5_DRVL0.530.96–
P3V3_S5_LL0.353.30–
P3V3_S5_REG_L0.361–320.000R
P3V3_S5_RF0.591.20–
P3V3_S5_VBST0.628.40–
P3V3_S5_VBST_R0.567––
P3V3_S5_VFB20.581.00–
P3V3_S5_VFB2_R0.370––
P3V3S5_EN_R0.533.40–
P3V3WLAN_VMON0.45––
P3V42G3H_BOOST0.61337.20–
P3V42G3H_FB0.70601.20–
P3V42G3H_SHDN_L0.372515.38–
P3V42G3H_SW0.323.40–
P5V_S4RS3_COMP10.741.96–
P5V_S4RS3_COMP1_ROL––
P5V_S4RS3_CSN10.435.00–
P5V_S4RS3_CSP11.295.00–
P5V_S4RS3_CSP1_R0.433––
P5V_S4RS3_DRVH0.975.20–
P5V_S4RS3_DRVL0.530.30–
P5V_S4RS3_FUNC0.000.00–
P5V_S4RS3_LL0.435.00–
P5V_S4RS3_REG_L0.435––
P5V_S4RS3_VBST0.6210.10–
P5V_S4RS3_VBST_R0.638––
P5V_S4RS3_VFB10.581.00–
P5V_S4RS3_VFB1_R0.443––
P5V_S4RS3_VFB1_XW0.433––
P5VP3V3_SKIPSEL0.482.00–
P5VP3V3_VREF20.482.00–
P5VP3V3_VREG30.563.30–
P5VS4RS3_EN0.489––
P5VS4RS3_EN_DOL––
P5VS4RS3_EN_R0.473.30–
P5VS4RS3_EN_RC0.488––
P5VS4RS3_PGOOD0.503.30–
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.484––
PBUSVSENS_EN_L_DIVOL––
PCH_CLK32K_RTCX10.44250.43–
PCH_HSIO_PWR_EN0.527––
PCH_SML1ALERT_L0.637––
PCH_STRP_TOPBLK_SWP_L0.580––
PCIE_AP_D2R_N0.37380.002–
PCIE_AP_D2R_P0.37610.002–
PCIE_AP_R2D_NOL0.002–
PCIE_AP_R2D_POL0.002–
PCIE_CLK100M_AP_N0.28270.000–
PCIE_CLK100M_AP_P0.28270.002–
PCIE_CLK100M_SSD_N0.230––
PCIE_CLK100M_SSD_P0.29––
PCIE_SSD_D2R_N<1>0.305––
PCIE_SSD_D2R_N<2>0.304––
PCIE_SSD_D2R_N<3>0.309––
PCIE_SSD_D2R_P<0>0.37––
PCIE_SSD_D2R_P<1>0.310––
PCIE_SSD_D2R_P<2>0.307––
PCIE_SSD_D2R_P<3>0.312––
PCIE_SSD_R2D_N<0>OL––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_N<2>OL––
PCIE_SSD_R2D_N<3>OL––
PCIE_SSD_R2D_P<0>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_SSD_R2D_P<2>OL––
PCIE_SSD_R2D_P<3>OL––
PCIE_WAKE_L0.487––
PDCINVSENS_EN_L_DIVOL––
PDDR_S3_REG_L0.141.20–
PLT_RESET_L–3.30–
PLT_RST_BUF_L–3.30–
PM_CLKRUN_L0.5663––
PM_PCH_PWROK0.66––
PM_PWRBTN_L0.629––
PM_SLP_S3_BUF_L0.46––
PM_SLP_S5_L0.473––
PM_THRMTRIP_R_LOL––
PP0V6_S0_DDRVTT0.1820.60–
PP1V2_CAM0.276––
PP1V2_CAM_PCIE_PVDD_FLT0.342––
PP1V2_CAM_PCIE_VDD_FLT0.342––
PP1V2_CAM_XTALPCIEVDD0.34211.10–
PP1V2_S30.1401.20–
PP1V2_S5_SMC_VDDC0.517––
PP1V05_S00.1311.00–
PP1V5_S0–1.50–
PP1V05_S0_REG_R0.131–151.000R
PP1V5_S0SW_AUDIO0.36751.50–
PP1V05_SUS0.295––
PP1V8_S30.393––
PP1V8_S3_REG_R0.393––
PP1V35_CAM0.247––
PP3V3_S00.60 Backlight driver off0.35233.30–
PP3V3_S0_CPUTHMSNS_R0.406––
PP3V3_S0_FET_R0.352––
PP3V3_S0SW_LCD0.631––
PP3V3_S0SW_LCD_R0.631––
PP3V3_S0SW_LCD_UF0.5873––
PP3V3_S0SW_SSD0.563––
PP3V3_S0SW_SSD_FET_R0.563––
PP3V3_S0SW_SSD_FLT0.55––
PP3V3_S30.487––
PP3V3_S3_FET_R0.487––
PP3V3_S3RS0_CAMERA0.359––
PP3V3_S3RS0_CAMERA_R0.359––
PP3V3_S40.38993.300–
PP3V3_S4_FET_R0.395––
PP3V3_S4_IPD0.38––
PP3V3_S4_TBTAPWR0.36––
PP3V3_S50.35413.30–
PP3V3_S5_AVREF_SMC0.5952––
PP3V3_S5_REG_R0.361–320.000R
PP3V3_S5_SMC_VDDA0.320––
PP3V3_S5RS3RS0_SYSCLKGEN0.35393.30–
PP3V3_SUS0.350––
PP3V3_SUS_FET_R0.350––
PP3V3_TBTLC0.40313.30–
PP3V3_WLAN0.5083.310–
PP3V3_WLAN_R0.508––
PP3V3RHV_S4_TBTAPWR0.55––
PP3V3RHV_S4_TBTAPWR_F0.550––
PP3V42_G3H0.3203.40–
PP3V42_G3H_SMC_SPVSR0.3080––
PP5V_S01.51 Backlight driver off0.430––
PP5V_S0_ALT_AUD_LDO_ENOL––
PP5V_S0_CPUVR_VDD0.430––
PP5V_S0_FET_R0.430––
PP5V_S3_RTUSB_A_F0.493––
PP5V_S3_RTUSB_A_ILIM0.493––
PP5V_S3_U62100.433––
PP5V_S3RS0_ALSCAM_F0.4039––
PP5V_S4_IPD0.4374––
PP5V_S4RS30.4355.00–
PP5V_S50.455.00–
PP5V1_CHGR_VDD0.45085.00–
PP5V1_CHGR_VDDP0.45215.00–
PP15V_TBT0.56––
PP18V5_DCIN_ISOL_ROL––
PPBUS_G3H0.1658.500–
PPBUS_G3H_R0.170––
PPBUS_S5_HS_COMPUTING_ISNS0.1648.60–
PPBUS_S5_HS_OTHER_ISNS0.1658.60–
PPCHGR_DCIN_D_R0.655––
PPDCIN_G3HOL––
PPDCIN_G3H_CHGR0.626––
PPDCIN_G3H_INRUSH0.626––
PPDCIN_G3H_ISOLOL––
PPDDR_S3_REG_R0.140––
PPHV_S0SW_LCDBKLT0.608––
PPVBAT_G3H_CHGR_R0.165––
PPVBAT_G3H_CHGR_REG0.1658.500–
PPVBAT_G3H_CONNOL––
PPVCC_S0_CPU0.0421.800147.000
PPVCC_S0_CPU_PH10.0421.80063.47R 1.3GHz 4GB82.25R 1.4GHz 4GB49.00R 1.7GHz 8GB147.000
PPVCC_S0_CPU_PH20.0421.80063.33R 1.3GHz 4GB82.53R 1.4GHz 4GB49.92R 1.7GHz 8GB147.000
PPVIN_G3H_P3V42G3H0.39415.38–
PPVIN_S0_CPUVR_VIN0.174––
PPVIN_S0SW_LCDBKLT0.427––
PPVIN_S0SW_LCDBKLT_FET0.43––
PPVIN_S0SW_LCDBKLTFET0.166––
PPVIN_S4SW_TBTBST_FET0.537––
PPVMEMIO_S0_CPU0.140––
PPVOUT_SW_LCDBKLT_FBOL Backlight driver off0.58––
PPVRTC_G3H0.43423.40–
PPVTT_S3_DDR_BUF0.4900.60–
S0PGD_BJT_GND_R–0.09–
S0PGD_C–0.12–
S4_PWR_EN0.46––
S5_PWR_EN0.543––
S5_PWRGD0.573.30–
SMBUS_SMC_1_S0_SCL0.5476––
SMBUS_SMC_1_S0_SDA0.5447––
SMBUS_SMC_2_S3_SCL0.7146––
SMBUS_SMC_2_S3_SDA0.7165––
SMBUS_SMC_3_SCL0.7064––
SMBUS_SMC_3_SDA0.7069––
SMBUS_SMC_5_G3_SCL0.5003.30–
SMBUS_SMC_5_G3_SDA0.4963.30–
SMC_1V2S3_ISENSE0.748––
SMC_BC_ACOK0.52633.30–
SMC_BIL_BUTTON_L0.750––
SMC_BMON_DISCRETE_ISENSE0.748––
SMC_BMON_ISENSE0.750––
SMC_CAMERA_ISENSE0.750––
SMC_CLK32K0.705––
SMC_CPU_DBGPWR_RD_L0.29––
SMC_CPU_ISENSE0.748––
SMC_CPU_VSENSE0.744––
SMC_CPUDDR_ISENSE0.749––
SMC_CPUVR_ADJUST_ISENSE0.729––
SMC_DCIN_ISENSE0.749––
SMC_DCIN_VSENSE0.745––
SMC_EXTAL0.777––
SMC_FAN_0_TACH0.71––
SMC_HS_COMPUTING_ISENSE0.748––
SMC_LCDBKLT_ISENSE0.750––
SMC_LID0.7349––
SMC_LSOC_RST_LOL––
SMC_MANUAL_RST_L0.6581––
SMC_ONOFF_L0.6517––
SMC_OOB1_D2R_CONN_L0.669––
SMC_OOB1_R2D_CONN_L0.699––
SMC_OOB1_R2D_L0.684––
SMC_OTHER_HI_ISENSE0.749––
SMC_P1V05S0_ISENSE0.749––
SMC_P1V05S0_VSENSE0.743––
SMC_P3V3S0_ISENSE0.751––
SMC_P3V3S5_ISENSE0.753––
SMC_PANEL_ISENSE0.750––
SMC_PBUS_VSENSE0.744––
SMC_PCH_SUSACK_L0.614––
SMC_PCH_SUSWARN_L0.631––
SMC_PECI_L0.74––
SMC_PECI_L_R0.750––
SMC_PM_G2_EN0.533.40–
SMC_PME_S4_DARK_L0.529––
SMC_PME_S4_WAKE_L0.496––
SMC_PROCHOT0.752––
SMC_PWRFAIL_WARN_L0.420––
SMC_RESET_L0.50003.300–
SMC_ROMBOOT1.5659––
SMC_RX_L0.7385––
SMC_S4_WAKESRC_EN0.751––
SMC_S5_PWRGD_VIN0.752––
SMC_SENSOR_ALERT_L0.519––
SMC_SSD_ISENSE0.748––
SMC_TCK0.7356––
SMC_TDI0.7374––
SMC_TDO0.7389––
SMC_THRMTRIP0.749––
SMC_TMS0.7371––
SMC_TOPBLK_SWP_L0.710––
SMC_TX_L0.750––
SMC_VCCIO_CPU_DIV20.744––
SMC_WAKE_L0.750––
SMC_WIFI_PWR_EN0.42––
SMC_WLAN_ISENSE0.751––
SMC_XTAL0.767––
SMC_XTAL_ROL––
SMS_INT_L0.750––
SPI_ALT_CLK0.5581––
SPI_ALT_CS_L0.5589––
SPI_ALT_MISO0.5043––
SPI_ALT_MOSI0.5294––
SPI_MISO_R0.499––
SPI_MLB_CLK0.5493––
SPI_MLB_CS_L0.5523––
SPI_MLB_MISO0.4898––
SPI_MLB_MOSI0.4977––
SPI_SMC_CS_L0.608––
SPI_WP_L0.6319––
SPIROM_USE_MLB0.4771––
SPKRAMP_INR_NOL––
SPKRAMP_INR_POL––
SPKRAMP_ROUT_N0.517––
SPKRAMP_ROUT_P0.517––
SPKRAMP_SHDN_L0.6040––
SSD_CLKREQ_CONN_L0.47––
SSD_DEVSLP0.440––
SSD_PCIE_SEL_L0.440––
SSD_PWR_EN0.393––
SSD_RESET_CONN_L0.47––
SYS_DETECT_L1.722––
SYS_ONEWIRE0.751––
SYSCLK_CLK25M_CAMERA0.43860.57–
SYSCLK_CLK25M_TBT0.42351.70–
SYSCLK_CLK25M_X10.43401.40–
SYSCLK_CLK25M_X20.441––
SYSCLK_CLK25M_X2_R0.43590.95–
TBT_A_HV_EN0.47––
TBTAPWRSW_ISET_S00.48––
TBTAPWRSW_ISET_S30.48––
TBTAPWRSW_ISET_V3P30.00––
TBTBST_BOOST0.537––
TP_SMC_5VSW_PWR_EN0.751––
TP_SMC_MD1OL––
TP_SMC_TRST_LOL––
TPAD_SPI_CLK0.538––
TPAD_SPI_CLK_R0.5413––
TPAD_SPI_CS_L0.562––
TPAD_SPI_CS_R_L0.74––
TPAD_SPI_IF_EN_CONN0.69––
TPAD_SPI_INT_L0.634––
TPAD_SPI_INT_S4_WAKE_L_CONN0.4934––
TPAD_SPI_MISO0.525––
TPAD_SPI_MISO_R0.5307––
TPAD_SPI_MOSI0.547––
TPAD_SPI_MOSI_R0.5514––
TPAD_USB_IF_EN_CONN0.6759––
TPAD_WAKE_L0.0004––
UNCONNECTED_172–0.00–
UNCONNECTED_251–0.11–
UNCONNECTED_252–0.09–
USB_BT_CONN_N0.77790.027–
USB_BT_CONN_P0.77733.320–
USB_EXTB_N0.4309––
USB_EXTB_P0.4299––
USB_PWR_EN0.4658––
USB_TPAD_N0.7927––
USB_TPAD_P0.4290––
USB3_EXTB_D2R_RC_N0.3608––
USB3_EXTB_D2R_RC_P0.3630––
USB3_EXTB_R2D_NOL––
USB3_EXTB_R2D_POL––
VMON_Q2_BASE–0.65–
VMON_Q3_BASE–0.66–
VMON_Q4_BASE–0.74–
VREFMRGN_MEMVREG_BUFOL––
WIFI_EVENT_L0.73473.310–
XDP_CPU_TDI0.331––
XDP_CPU_TDO0.1811.00–
XDP_CPUPCH_TRST_L–0.00–
XDP_JTAG_CPU_ISOL_L0.5644.90–
XDP_LPCPLUS_GPIO0.5134––
XDP_PCH_TDI0.300––
XDP_PCH_TDO0.3001.00–
XDP_PCH_TMS0.297––
XDP_SSD_PCIE1_SEL_L0.505––
XDP_SSD_PCIE2_SEL_L0.507––
XDP_TRST_L0.6550.00–
XDP_USB_EXTB_OC_L0.5147––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3437?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3437: diode 0.165, voltage 8.500. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3437?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3437: diode 0.320, voltage 3.40. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3437?

OpenBoardData's known-good values for PP5V_S5 on the 820-3437: diode 0.45, voltage 5.00. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3437 board?

Open your own 820-3437 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License