Apple laptop board · OpenBoardData

820-3662 known-good readings

Known-good readings for the Apple laptop board 820-3662: 1,320 nets, including 95 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 94 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3662.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 95 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0v32––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, indicated by the "G3H" suffix in its name. The archive lists a known-good diode reading of 0v32 on this net; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V42_G3H to ground and compare against 0v32. Then apply power and check the rail's voltage. A diode reading far from 0v32 usually points to a short or a faulty component on the rail, but confirm with voltage and resistance checks before replacing anything.

PP3V42_G3H_SMC_SPVSR0.318––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is the always-on 3.42 V rail feeding the SMC's SPVSR input, judging by the name (G3H = always on). The archive lists one known-good reading: diode 0.318 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the net, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.318 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PPBUS_G3H0v45––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the G3H suffix indicates it is always-on, which comes from the rail name rather than a schematic. The only known-good reading here is a diode value of 0v45 to ground, with no condition recorded. Check it unpowered in diode mode from PPBUS_G3H to ground, then measure its voltage with power applied; no known-good voltage is listed here. A diode reading far from 0v45 usually points to a short or a leaky part on the rail, but confirm with a voltage check before replacing anything.

PPBUS_G3H_R0.471––
AI: what PPBUS_G3H_R is and how to check it
  • What it is: PPBUS_G3H_R is the main bus rail; the G3H part of the name indicates it's always-on (from the name, not from a schematic).
  • Known-good reading: diode 0.471 to ground, from the community archive, so treat it as a guide only. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from PPBUS_G3H_R to ground; then apply power and measure the rail's voltage.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail, but one reading doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.
PPDCIN_G3H0v68––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, from its name: the DC input side that should be present whenever the charger is connected. The only known-good figure here is a diode reading of 0v68 to ground, taken with the board unpowered; there is no known-good voltage reading for this rail in the data. Check it in diode mode to ground first, then measure the voltage with the charger connected. A diode reading far below 0v68 usually points to a short or a leaky part on the rail, while a much higher or open reading suggests a broken connection or missing component; treat these as a guide, not a confirmed fault.

PPDCIN_G3H_CHGR0v63––
AI: what PPDCIN_G3H_CHGR is and how to check it
  • What it is: PPDCIN_G3H_CHGR is the charger-side DC input rail; the "G3H" part of the name indicates an always-on rail, and "CHGR" points to the charger section (both from the name).
  • Known-good reading: diode 0v63 to ground, from the readings archive. This is a community value and a guide only; no known-good voltage reading for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0v63. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with voltage under power before replacing anything.
PPDCIN_G3H_INRUSH0v63––
AI: what PPDCIN_G3H_INRUSH is and how to check it
  • What it is: From the name, PPDCIN_G3H_INRUSH is the always-on (G3H) DC input rail, with "INRUSH" suggesting the inrush-current path from the adapter input. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0v63 to ground (community reading, a guide only; board state affects it). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0v63. Then apply power and measure the DC voltage on the rail; there's no known-good voltage to compare against, so compare with a matching input rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail, a much higher one to an open path. Confirm with resistance and voltage before replacing anything.
PPDCIN_G3H_ISOLOL––
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is the isolated DC-input rail, and the G3H in its name indicates it is always-on. The archive has only a diode reading for it, OL (open), with no condition noted; there is no known-good voltage or resistance reading here. With the board unpowered, check it in diode mode to ground and compare against that OL; then apply power and measure its voltage, which should be present whenever the adapter is connected. A diode reading far below OL would suggest a short or a leaky path on that rail, but one reading alone doesn't confirm a bad part.

PPVBAT_G3H_CHGR_R0.450––
AI: what PPVBAT_G3H_CHGR_R is and how to check it
  • What it is: PPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H part of the name indicates it is an always-on rail, and CHGR points to the charger circuit. This is inferred from the name only.
  • Known-good reading: diode 0.450 to ground, from the readings archive. This is a community guide, not a factory spec, and the archive gives no known-good voltage for this rail.
  • How to check: with the board unpowered and the battery disconnected, measure diode mode from PPVBAT_G3H_CHGR_R to ground, then apply power and measure the rail's voltage.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one can mean an open path. A single reading doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.
PPVBAT_G3H_CHGR_REG0v45––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a charger-side battery rail; the G3H in its name indicates it is always-on, and CHGR points to the charging circuit. The only known-good reading here is a diode value of 0v45 to ground, with no condition noted and no known-good voltage or resistance reading. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. A diode reading far from 0v45 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PPVBAT_G3H_CONNOL––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judged from its name; the "CONN" part suggests it sits at the battery connector. The only archived reading is a diode value of OL to ground, with no condition recorded and no known-good voltage or resistance here. Check it unpowered in diode mode from the net to ground, then with power applied measure the voltage at the connector. A far-off diode reading usually points to an open trace or connector contact rather than a short, but one reading doesn't confirm a fault.

PPVIN_G3H_P3V42G3H0.609––
AI: what PPVIN_G3H_P3V42G3H is and how to check it

PPVIN_G3H_P3V42G3H is an always-on rail, judging from the G3H in its name (general naming convention, not board data). The only known-good reading recorded is a diode value of 0.609 to ground, with no condition stated; there is no known-good voltage or resistance reading here.

  • Check it unpowered in diode mode from the net to ground and compare with 0.609.
  • Then apply power and measure the voltage on the net; no known-good voltage is recorded, so compare against a known-good board or the same rail on a matching circuit.
  • A diode reading far below 0.609 usually points to a short or a leaky part on the rail; a reading far above it can mean an open connection. One reading alone doesn't confirm a bad part, so check the voltage next before replacing anything.
PPVRTC_G3H0.446––
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on RTC rail; the "G3H" suffix indicates it stays powered whenever the adapter or battery is present, which comes from the rail name rather than a schematic. The archive lists one known-good diode reading of 0.446 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then measure its voltage with power applied, comparing against a known-good board for the voltage. A diode reading far from 0.446 usually points to a short or leaky component on the rail, but a single reading doesn't confirm a fault.

S5 and SUS: standby 13

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.524––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC is a 1.2 V rail; the "S5" in the name marks it as a standby-stage supply, and "SMC_VDDC" suggests it feeds the SMC (general reading of the name, not from board data). The only known-good figure here is a diode reading of 0.524 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading is available for this rail, so compare against a matching rail or a known-good board. A diode value far below 0.524 usually points to a short or leaky part on the rail; a much higher one can mean an open path, but one reading alone doesn't confirm a fault.

PP1V05_SUS0.350––
AI: what PP1V05_SUS is and how to check it

PP1V05_SUS is a 1.05 V standby rail; the "SUS" in the name indicates it is present in the standby state, before the board fully powers on. The only known-good reading here is a diode value of 0.350 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far below 0.350 usually points to a short or a leaky load on the rail, while a much higher reading can mean an open path; confirm with a voltage check before suspecting any part.

PP3V3_S50v14––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the "S5" in the name marks it as a standby-stage supply, from the name only. The archive lists one known-good reading for this net: diode 0v14, with no condition noted, so treat it as a guide. Check it with the board unpowered in diode mode from PP3V3_S5 to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching standby rail or a known-good board. A diode reading far from 0v14 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S5_AVREF_SMC0.609––
AI: what PP3V3_S5_AVREF_SMC is and how to check it
  • What it is: From its name, PP3V3_S5_AVREF_SMC is a 3.3 V standby (S5) reference rail feeding the SMC. The "AVREF" part suggests an analog reference, but that's general interpretation, not from board data.
  • Known-good reading: Diode mode to ground, 0.609. That's the only known-good value recorded here; no voltage or resistance reading is listed.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.609. Then power up and measure the DC voltage; expect roughly 3.3 V from the name, though no known-good voltage is recorded here.
  • If it's far off: A much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open feed. Confirm with voltage and resistance before replacing anything.
PP3V3_S5_DBGLEDOL––
AI: what PP3V3_S5_DBGLED is and how to check it

PP3V3_S5_DBGLED is a 3.3 V standby rail feeding the debug LED, judging by its name (PP = power rail, 3V3 = 3.3 V, S5 = standby stage, DBGLED = debug LED). The only archived reading is a diode-mode value of OL to ground, with no condition recorded, so treat it as a guide rather than a spec. No known-good voltage reading exists here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below OL suggests a short or leaky load on the rail; a missing voltage with a normal diode reading points upstream to the standby supply or its enable.

PP3V3_S5_SMC_VDDA0.320––
AI: what PP3V3_S5_SMC_VDDA is and how to check it
  • What it is: PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply, judging from the name (PP = power rail, 3V3 = 3.3 V, S5 = standby stage, SMC_VDDA = SMC analog supply). That's from the name, not from board data.
  • Known-good reading: diode 0.320 in the readings archive, with no condition recorded. There is no known-good voltage or resistance value here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail, and a missing or low voltage points to the standby supply or an enable upstream. Confirm with a second measurement before replacing anything.
PP3V3_SUS0v33––
AI: what PP3V3_SUS is and how to check it
  • What it is: PP3V3_SUS is a 3.3 V standby rail; the "SUS" in the name marks it as a suspend/standby supply that should be present before the board fully powers on.
  • Known-good reading: diode-to-ground 0v33, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_SUS to ground and compare with 0v33; then apply power and measure the rail voltage. Community readings vary with board state, so treat 0v33 as a guide, not a spec.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, while a missing voltage with a normal diode reading points upstream to the standby supply that creates it. No known-good voltage value here, so compare against a matching standby rail or a known-good board before replacing anything.
PP5V_S50v46––
AI: what PP5V_S5 is and how to check it
  • What it is: PP5V_S5 is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage (from the name).
  • Known-good reading: diode 0v46 to ground, from the readings archive. This is a community value and only a guide; no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S5 to ground and compare with 0v46. Then apply power and measure the rail voltage; there is no known-good voltage here, so compare against a matching rail on a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail, and a much higher one to an open connection. Confirm with a second measurement before replacing anything.
PP5V_S5_CUMULUS0v46––
AI: what PP5V_S5_CUMULUS is and how to check it

PP5V_S5_CUMULUS is a standby rail, judged from its S5/SUS name — a 5 V supply that should be present in standby, before the board fully powers on. The only known-good reading here is a diode value of 0v46 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0v46 usually points to a short or a leaky part on that rail, but treat it as a guide and confirm with a second measurement before replacing anything.

PPVIN_S5_HS_COMPUTING_ISNS0.450––
AI: what PPVIN_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From the name, PPVIN_S5_HS_COMPUTING_ISNS is a high-side current-sense (ISNS) input tied to the S5 standby rail. The board data doesn't list which parts sit on it.
  • Known-good reading: Diode mode to ground, 0.450. This is a community guide, not a factory spec; no known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then power up and measure the voltage on it.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on that net; a much higher one to an open. Confirm with a second measurement before replacing anything.
PPVIN_S5_HS_OTHER3V3_ISNS0v45––
AI: what PPVIN_S5_HS_OTHER3V3_ISNS is and how to check it
  • What it is: From its name, PPVIN_S5_HS_OTHER3V3_ISNS is a 3.3 V input rail in the S5 standby stage, with "ISNS" suggesting a current-sense line. The exact parts on it aren't known here.
  • Known-good reading: diode 0v45 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the net to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PPVIN_S5_HS_OTHER5V_ISNS0v45––
AI: what PPVIN_S5_HS_OTHER5V_ISNS is and how to check it
  • What it is: From its name, PPVIN_S5_HS_OTHER5V_ISNS is a standby (S5/SUS) input-sense rail for a 5V high-side supply on the 820-3662. It is a current-sense (ISNS) line, so it likely reports current on that 5V path rather than being a heavy load rail.
  • Known-good reading: Diode mode to ground is 0v45 (from the readings archive; community-contributed, so treat it as a guide). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0v45. Then apply power and measure the DC voltage on the rail; there is no known-good voltage in this data, so compare against a matching net or a known-good board.
  • If it's far off: A much lower diode reading usually points to a short or leaky part on that net; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP_R0.393––
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it
  • What it is: From the name, a standby (S5/SUS) power output rail for the PCH, likely a bypass/decoupling feed. The board data only gives the name and stage, not the parts on it.
  • Known-good reading: diode 0.393 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode to ground on the rail; then power up and measure the voltage, comparing against a known-good board since no voltage value is listed.
  • If far off: a low diode reading usually points to a short or leaky part on the rail; a high or open reading to a broken feed. Confirm with voltage before replacing anything.

S4 11

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40v40––
AI: what PP3V3_S4 is and how to check it
  • PP3V3_S4 is a 3.3 V rail; the "S4" suffix (from the name) places it in the S4 startup stage, so it should come up partway through the power sequence, not at standby.
  • Known-good reading in the archive: diode 0v40 to ground. No known-good voltage reading is listed here.
  • To check it: power off and unplug, then diode mode from PP3V3_S4 to ground and compare with 0v40. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0v40 usually points to a short or a leaky part on the rail; far above it can mean an open path. Confirm with the voltage reading before replacing anything.
PP3V3_S4_TBT0.413––
AI: what PP3V3_S4_TBT is and how to check it

PP3V3_S4_TBT is a 3.3 V rail that, from its name, belongs to the S4 startup stage and the Thunderbolt side of the board. The only known-good reading here is a diode value of 0.413; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.413 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S4_TBT_F0.412––
AI: what PP3V3_S4_TBT_F is and how to check it

PP3V3_S4_TBT_F is a 3.3 V rail; the S4 in its name marks it as a startup-stage rail, and TBT suggests it feeds the Thunderbolt section (both from the name, not confirmed by parts data). The only known-good reading here is diode 0.412 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.412 usually points to a short or a leaky part on the rail, but one reading doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S4_TBTAPWR0.375––
AI: what PP3V3_S4_TBTAPWR is and how to check it

PP3V3_S4_TBTAPWR is a 3.3 V rail; the name indicates it's a 3.3 V supply in the S4 power state, and "TBTAPWR" suggests it feeds Thunderbolt-related power (that part is from the name, not confirmed by board data). The only known-good reading here is a diode value of 0.375 to ground; there's no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.375 usually points to a short or a damaged component on that rail, but a single reading isn't proof — compare with a matching rail or a known-good board before replacing anything.

PP3V3_S4_TBTBPWR0.372––
AI: what PP3V3_S4_TBTBPWR is and how to check it

PP3V3_S4_TBTBPWR is a 3.3 V rail in the S4 power state, from its name; the "TBTBPWR" part suggests it feeds Thunderbolt-related power, though that's general reading, not from this board's data. The archive lists one known-good diode reading of 0.372, with no condition noted, and no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.372 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare with a matching net or a known-good board before replacing anything.

PP3V3RHV_S4_TBTAPWR0.559––
AI: what PP3V3RHV_S4_TBTAPWR is and how to check it
  • What it is: From the name, PP3V3RHV_S4_TBTAPWR is a 3.3 V rail in the S4 startup stage, likely feeding Thunderbolt-related power (TBTAPWR). The exact parts on it aren't known here.
  • Known-good reading: diode 0.559 to ground, from the readings archive. No voltage or resistance reading is recorded for this rail.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.559. Then apply power and measure the rail voltage; no known-good voltage is listed, so compare against a known-good board or the rail's expected 3.3 V.
  • If it's far off: A diode reading well below 0.559 suggests a short or leaky part on the rail; a much higher or open reading suggests a broken trace or missing feed. These are guides only, not confirmed faults.
PP3V3RHV_S4_TBTAPWR_F0.559––
AI: what PP3V3RHV_S4_TBTAPWR_F is and how to check it
  • What it is: From the name, PP3V3RHV_S4_TBTAPWR_F is a 3.3 V rail (PP3V3) in the S4 startup stage, tied to Thunderbolt power (TBTAPWR). The "HV" suffix likely means a higher-voltage variant of that 3.3 V feed; that part is general naming, not from board data.
  • Known-good reading: diode 0.559 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.559. Then apply power and measure the DC voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail; a much higher one to an open feed. Confirm with the voltage measurement before replacing anything.
PP3V3RHV_S4_TBTBPWR0.561––
AI: what PP3V3RHV_S4_TBTBPWR is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) in the S4 startup stage, feeding Thunderbolt power (TBTBPWR). The "RHV" part of the name isn't explained by the available data.
  • Known-good reading: Diode 0.561 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail; expect about 3.3 V once S4 is reached, though that figure is general, not from this board's data.
  • If it's far off: A diode reading well below 0.561 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken trace or missing feed. Confirm with the voltage measurement before replacing anything, since one reading alone doesn't prove a part bad.
PP3V3RHV_S4_TBTBPWR_F0.560––
AI: what PP3V3RHV_S4_TBTBPWR_F is and how to check it
  • What it is: From its name, a 3.3 V rail (PP3V3) in the S4 startup stage, tied to Thunderbolt power (TBTBPWR). The board data has no parts list, so which components sit on it isn't known here.
  • Known-good reading: diode 0.560 to ground, from the community archive; treat it as a guide, not a spec.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; an open or high reading points to a missing feed or a broken connection. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board before condemning anything.
PP5V_S40v43––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging from its name (general naming convention, not board-specific data). The only archived reading is a diode value of 0v43 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from PP5V_S4 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0v43 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S4_AUDIO_XW0.430––
AI: what PP5V_S4_AUDIO_XW is and how to check it

PP5V_S4_AUDIO_XW is a 5 V audio rail that comes up at the S4 stage of startup, judging from its name. The only known-good reading recorded is a diode drop of 0.430 to ground; there is no known-good voltage reading here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.430.
  • Then power the board and measure the voltage at the rail; no known-good voltage is listed, so compare against a known-good board or the rail's expected 5 V.
  • A diode reading far below 0.430 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection or missing part.
  • This is a guide only, since readings vary with board state; confirm with a second measurement before replacing anything.

S3: memory 20

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V75_S3_MEM_VREFCA_A0.376––
AI: what PP0V75_S3_MEM_VREFCA_A is and how to check it
  • What it is: From its name, PP0V75_S3_MEM_VREFCA_A is a 0.75 V memory reference rail that comes up at the S3 (memory) stage. The exact parts on the net aren't known here.
  • Known-good reading: diode 0.376 (community archive, guide only). No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. Confirm with the voltage reading before replacing anything.
PP0V75_S3_MEM_VREFCA_B0v38––
AI: what PP0V75_S3_MEM_VREFCA_B is and how to check it
  • What it is: A 0.75 V memory reference rail; the S3 and MEM parts of the name indicate it belongs to the memory section and comes up in the S3 (suspend-to-RAM) power stage. This is read from the name, not from a board file.
  • Known-good reading: diode 0v38 to ground, from the readings archive. No known-good voltage reading is available here.
  • How to check: with the board unpowered, measure diode mode from PP0V75_S3_MEM_VREFCA_B to ground and compare with 0v38; then apply power and measure the rail voltage, comparing against a known-good board since no voltage value is listed.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, while an open reading points to a missing connection. Treat this as a guide only, since readings vary with board state, and confirm with a second measurement before replacing anything.
PP0V75_S3_MEM_VREFDQ_A0.376––
AI: what PP0V75_S3_MEM_VREFDQ_A is and how to check it
  • What it is: From the name, a 0.75 V memory reference rail (VREFDQ) that comes up in the S3 (memory) stage. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.376 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.376. Then power up and measure the DC voltage; expect about 0.75 V from the name, but that figure is general, not from the board data.
  • If far off: a much lower diode reading points to a short or leaky part on the rail; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP0V75_S3_MEM_VREFDQ_B0v38––
AI: what PP0V75_S3_MEM_VREFDQ_B is and how to check it
  • What it is: A 0.75 V memory reference rail, from the name: PP0V75 = 0.75 V, S3 = memory power state, VREFDQ = the DDR data reference voltage. It's a reference, not a heavy load rail.
  • Known-good reading: diode 0v38 to ground, from the readings archive. That's a community guide, not a factory spec, and it varies with board state.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail; then power up and measure the DC voltage, which should sit near 0.75 V. No known-good voltage reading here, so compare against a matching rail or a known-good board.
  • If it's far off: a shorted or leaky part on the rail usually pulls the diode reading low; an open or missing feed shows high or open. Confirm with a second measurement before replacing anything.
PP1V35_S30.125––
AI: what PP1V35_S3 is and how to check it
  • What it is: PP1V35_S3 is a 1.35 V rail in the S3 (memory) startup stage, judged from its name; the parts it feeds aren't listed in the readings archive.
  • Known-good reading: diode 0.125 to ground, with no condition recorded. No known-good voltage reading here.
  • How to check: power off and measure diode mode from PP1V35_S3 to ground, then power on and measure the voltage.
  • If it's far off: a low diode reading usually points to a shorted load or part on the rail; a missing voltage points to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP1V35_S3_MEM0.125––
AI: what PP1V35_S3_MEM is and how to check it

PP1V35_S3_MEM is a 1.35 V memory rail in the S3 (suspend-to-RAM) power state, judged from the rail name. The archive lists one known-good reading: diode 0.125 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and confirm about 1.35 V in the S3 state. No known-good voltage reading is recorded here, so compare against a matching memory rail or a known-good board. A diode reading far from 0.125 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP1V35_S3RS0_CPUDDR0.136––
AI: what PP1V35_S3RS0_CPUDDR is and how to check it

PP1V35_S3RS0_CPUDDR is a 1.35 V memory rail; the S3 and CPUDDR parts of the name indicate it belongs to the memory stage (from the name, not from a schematic).

  • Known-good: diode 0.136 (archive reading, guide only, no condition recorded). No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered.
  • A diode reading far below 0.136 usually suggests a short or a leaky load on the rail; a much higher one can mean an open path. Confirm with a second measurement before replacing anything.
PP1V35_S3RS0_FET0.137––
AI: what PP1V35_S3RS0_FET is and how to check it

PP1V35_S3RS0_FET is a 1.35 V memory rail; the S3 and RS0 parts of the name indicate the memory stage, and that reading comes from the name rather than a schematic. The archive lists one known-good diode reading of 0.137 to ground, with no condition recorded and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.137 usually points to a short or a leaky part on that rail, but a single reading doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S30v45––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that is up in the S3 (memory/suspend) state, judged from its name. The archive lists one known-good reading for it: diode 0v45, with no condition noted, and there is no known-good voltage reading here. Check it unpowered in diode mode from PP3V3_S3 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0v45 usually points to a short or a leaky load on the rail, but one reading doesn't confirm a bad part, so compare with a matching net or a known-good board before replacing anything.

PP3V3_S3_FAN_CTL–3.30–
AI: what PP3V3_S3_FAN_CTL is and how to check it
  • What it is: PP3V3_S3_FAN_CTL is a 3.3 V S3 (memory-stage, from the name) fan control signal on the 820-3662. The name suggests a switched 3.3 V line that drives fan control, but that's general inference, not from board data.
  • Known-good reading: the archive lists 3.30 V for this net. No diode or resistance value is recorded here, so there's no known-good reading of that kind.
  • How to check: with the board unpowered, measure diode mode from the net to ground; then power up and measure the voltage, comparing it with the 3.30 V guide.
  • What a far-off reading suggests: a voltage well away from 3.30 V points to the rail not coming up or being loaded down, but one reading alone doesn't confirm a bad part. Compare with a matching net or a known-good board before replacing anything.
PP3V3_S3_PSOC0v40––
AI: what PP3V3_S3_PSOC is and how to check it

PP3V3_S3_PSOC is a 3.3 V rail in the S3 (memory) startup stage, judging from the name. The archive lists one known-good reading: diode 0v40 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure its voltage with the board powered. No known-good voltage reading is recorded here, so compare the powered voltage against a matching S3 rail or a known-good board. A diode reading far from 0v40 usually points to a short or a leaky load on the rail, but confirm with a second measurement before replacing anything.

PP3V3_S3_VREFMRGN0.509––
AI: what PP3V3_S3_VREFMRGN is and how to check it
  • What it is: From its name, PP3V3_S3_VREFMRGN is a 3.3 V S3 (memory-stage) reference/margin rail on the 820-3662. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.509 to ground, from the community archive; treat it as a guide, not a spec.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • No known-good voltage is listed here, so compare against a matching rail or a known-good board.
  • A diode reading far from 0.509 usually points to a short or a leaky part on that rail; confirm with voltage before replacing anything.
PP3V3_S3RS0_CAMERA0.357––
AI: what PP3V3_S3RS0_CAMERA is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA is a 3.3 V rail, from its name. The S3 in the name puts it at the memory/startup stage; the CAMERA part suggests it feeds camera circuitry, though that's general reading of the name, not from board data.
  • Known-good reading: diode 0.357 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.357; then power the board and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good usually points to a shorted part on the rail, and no or low voltage with power applied points to the rail not being enabled or its source failing. These are likely causes, not confirmed ones.
PP3V3_S3RS0_CAMERA_R0.357––
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA_R is a 3.3 V rail feeding the camera, from its name. The S3 in the name puts it in the memory/standby power stage (from the name, general convention).
  • Known-good reading: diode 0.357 to ground, from the readings archive; treat it as a guide since community readings vary with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.357. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. Confirm with the voltage measurement before replacing anything.
PP3V3_S3RS4_BT_F0v41––
PP5V_S30.493––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is the 5 V rail that comes up at the S3 (memory/suspend) stage of power-on, judged from its name. The archive lists one known-good diode reading of 0.493, with no condition recorded; there is no known-good voltage or resistance value here. Check it with the board unpowered in diode mode from PP5V_S3 to ground, then measure the voltage with power applied and the board brought out of standby. A diode reading far from 0.493 usually points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board.

PP5V_S3_LTUSB_A_F0.525––
AI: what PP5V_S3_LTUSB_A_F is and how to check it

PP5V_S3_LTUSB_A_F is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state and feeds the LTUSB_A section; the exact parts on it aren't known here. The only known-good reading in the archive is a diode value of 0.525 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading is listed here, so compare against a matching rail or a known-good board. A diode reading far from 0.525 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S3_LTUSB_A_ILIM0.524––
AI: what PP5V_S3_LTUSB_A_ILIM is and how to check it
  • What it is: From its name, PP5V_S3_LTUSB_A_ILIM is a 5 V S3 (memory/suspend-to-RAM stage) rail feeding the LTUSB A-side current-limit circuit. The board data only gives the net name and its startup stage, not which parts sit on it.
  • Known-good reading: diode 0.524 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the net to ground and compare with 0.524; then power up and measure the voltage on the net.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing connection. One reading alone doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.
PP5V_S3RS0_ALSCAM_F0v41––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it
  • What it is: From the name, PP5V_S3RS0_ALSCAM_F is a 5 V rail that comes up in the S3 (memory/suspend) stage and feeds the ALS camera circuit. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0v41 to ground, from the community archive, so treat it as a guide that varies with board state. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a missing voltage points to the rail not being enabled or its source not switching. Confirm with a second measurement before replacing anything.
PPVTTDDR_S30.489––
AI: what PPVTTDDR_S3 is and how to check it
  • What it is: PPVTTDDR_S3 is a memory-stage rail (S3), judging by its name; it's the DDR termination voltage rail. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.489 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure the DC voltage on the rail.
  • If it's far off: a low or shorted diode reading usually points to a shorted part or capacitor on the rail; a missing voltage with a normal diode reading points upstream to the rail's supply. Confirm with a second measurement before replacing anything.

S0: running 38

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.127––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail, and the S0 suffix indicates it belongs to the running state (both from the name). The archive lists one known-good diode reading of 0.127 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP1V05_S0 to ground and compare with 0.127; then power up and check the voltage is present in the S0 state. A diode reading far below known-good often suggests a short or a failing load on the rail, but one reading isn't proof, so confirm with a second measurement before replacing anything.

PP1V5_S00v30––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail in the S0 (running) state, judged from its name; it is not a startup rail. The archive lists one known-good reading: diode 0v30 to ground, with no condition noted, and no voltage or resistance value is recorded here. Check it unpowered in diode mode from PP1V5_S0 to ground, then power the board and measure the voltage at the rail. A diode reading far from 0v30 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault; compare with a matching rail or a known-good board.

PP1V5_S0_AUDIO_DIG0.346––
AI: what PP1V5_S0_AUDIO_DIG is and how to check it

PP1V5_S0_AUDIO_DIG is a 1.5 V digital audio rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "AUDIO_DIG" points to the digital audio section. The only known-good figure here is a diode reading of 0.346 to ground, with no condition recorded. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied and the board in S0. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode value far from 0.346 usually suggests a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PP1V05_S0_PCH_VCC_CLK_F0.125––
AI: what PP1V05_S0_PCH_VCC_CLK_F is and how to check it
  • What it is: PP1V05_S0_PCH_VCC_CLK_F is a 1.05 V rail, from its name, feeding the PCH clock section; the S0 in the name indicates it belongs to the running (S0) state.
  • Known-good reading: diode 0.125 to ground, from the readings archive. That's a community value and a guide only, and it varies with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.125; then power up and measure the voltage, which should sit near 1.05 V.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a correct diode reading with no or low voltage points back to the rail's supply or enable circuit. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
PP1V05_S0_PCH_VCC_CLK_R0.124––
AI: what PP1V05_S0_PCH_VCC_CLK_R is and how to check it

PP1V05_S0_PCH_VCC_CLK_R — from the name, a 1.05 V S0 (running-state) rail feeding the PCH clock supply. The only known-good reading here is a diode value of 0.124 to ground, with the board unpowered; there is no known-good voltage reading for this rail.

  • Check it with the board off: multimeter in diode mode, black probe on ground, red on the rail, and compare with 0.124.
  • Then power up and measure the DC voltage; expect roughly 1.05 V from the name, but that is general, not a recorded value here.
  • A diode reading far from 0.124 suggests a short or a leaky part on the rail; a missing voltage with a normal diode reading points more to the supply or its enable.
PP1V05_S0_REG_R0.127––
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "REG" suggests a regulated supply. The archive lists one known-good reading: diode 0.127 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.127 usually points to a short or a leaky part on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V5R1V35_S0_RIO0.345––
AI: what PP1V5R1V35_S0_RIO is and how to check it
  • What it is: From its name, PP1V5R1V35_S0_RIO is a running-state (S0) rail for the RIO block, with a nominal 1.5 V and 1.35 V in the name. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.345 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading is listed here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.345; then power the board and measure the rail voltage.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail, but one reading doesn't confirm a bad part — compare against a matching rail or a known-good board before replacing anything.
PP3V3_S00v343.30–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V supply rail for the S0 (running) state, judged from its name; it should be present once the board is fully on. In the readings archive its known-good values are a diode reading of 0v34 to ground and 3.30 V with power applied — community figures, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 3.30 V points to the rail not coming up or being loaded down, while a diode reading far from 0v34 suggests a short or an open on that net; no known-good resistance reading is recorded here.

PP3V3_S0_AUDIO_ANALOG0.358––
AI: what PP3V3_S0_AUDIO_ANALOG is and how to check it
  • What it is: From the name, PP3V3_S0_AUDIO_ANALOG is a 3.3 V rail feeding the analog audio section, active in the S0 (running) state. The exact parts on it aren't known here.
  • Known-good reading: diode 0.358 to ground, from the readings archive; treat it as a guide, not a spec.
  • How to check: power off and unplug, then diode-mode from the rail to ground. Then power up and measure the voltage; no known-good voltage reading is available here, so compare against a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open trace or missing feed. Confirm with voltage before replacing anything.
PP3V3_S0_CPUTHMSNS_R0.4053.30–
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R is a 3.3 V S0 (running-state) rail; from the name, it's a CPU thermal-sensor sense line. The archive's known-good readings are diode 0.405 and voltage 3.30, with no condition noted.

  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Expect about 0.405.
  • Then power the board and measure the voltage; expect about 3.30 V in S0.
  • No known-good resistance reading here; compare against a matching net or a known-good board.

A diode reading far below 0.405 suggests a short or leaky part on the rail; a missing 3.3 V with power applied points to the rail not coming up or a break in the line. These are likely causes, not confirmed ones.

PP3V3_S0_FINTHMSNS_R0.403––
AI: what PP3V3_S0_FINTHMSNS_R is and how to check it
  • What it is: From the name, PP3V3_S0_FINTHMSNS_R is a 3.3 V S0 (running-state) rail tied to a thermal sensor sense line. The exact parts on it aren't known here.
  • Known-good reading: diode 0.403 in the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the net to ground; then power up and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with a voltage check before replacing anything.
PP3V3_S0_VMON_P2OL––
AI: what PP3V3_S0_VMON_P2 is and how to check it

PP3V3_S0_VMON_P2 is a 3.3 V rail, going by its name: the 3V3 and S0 (running state) parts, with VMON suggesting a voltage-monitor sense line. The only known-good reading in the archive is a diode reading of OL to ground, with the board unpowered. No known-good voltage reading here, so compare the powered voltage against the rail it monitors rather than a fixed number. A diode reading far from OL (a low reading to ground) usually points to a short or a leaky part on that net, but confirm with a second measurement before replacing anything.

PP3V3_S0_VMON_P7OL––
AI: what PP3V3_S0_VMON_P7 is and how to check it

PP3V3_S0_VMON_P7 is a 3.3 V rail from its name, with the S0 suffix indicating it belongs to the running state. The only archived reading is a diode value of OL to ground, which is a guide from community contributions rather than a guaranteed value. With the board unpowered, measure diode mode from the rail to ground and compare with that OL reading; then apply power and check the voltage. A far lower diode reading than OL usually points to a short or a leaky part on the rail, but no known-good voltage reading exists here, so compare against a matching rail or a known-good board.

PP3V3_S0SW_SSD0.657––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a switched 3.3 V rail feeding the SSD, and the S0 in its name indicates it belongs to the running (S0) power state. The archive lists a known-good diode reading of 0.657 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.657 usually points to a short or a leaky load on the rail, while a correct diode reading with no voltage points upstream to the switch or enable that turns the rail on. These are community readings and vary with board state, so treat them as a guide rather than a confirmed fault.

PP3V3_S0SW_SSD_FLT0v64––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a 3.3 V rail switched on in the S0 (running) state, feeding the SSD; the S0SW and SSD parts come from the name, and FLT likely means a filtered feed. The archive lists one known-good diode reading of 0v64, with no condition noted and no voltage reading recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0v64 suggests a short or leaky part on that net, but one reading alone doesn't confirm a fault, so compare with a matching net or a known-good board. No known-good voltage reading is available here.

PP3V3_S0SW_SSD_R0.657––
AI: what PP3V3_S0SW_SSD_R is and how to check it

PP3V3_S0SW_SSD_R — reference note

  • From its name, this is a 3.3 V rail (PP3V3) that is switched (SW) and active in the S0 running state, feeding the SSD circuit (SSD_R). The "SW" suggests it is gated by a switch or load-switch device rather than always on.
  • Known-good reading in the archive: diode mode to ground 0.657, with no condition noted. There is no known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.657. Then apply power and measure the voltage at the rail, expecting about 3.3 V once the board is in S0.
  • A diode reading far below 0.657 usually points to a short or a failing load on the rail; far above it can mean an open path. A missing or low voltage with a normal diode reading points more toward the switch, its enable signal, or the upstream supply. These are likely causes, not confirmed ones.
PP5V_S00v415.00–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail for the S0 (running) state, as the name indicates. In the readings archive it shows a diode reading of 0v41 to ground and 5.00 V with power applied; these are community readings and a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A voltage well below 5.00 V points to the rail not coming up or being loaded down, while a diode reading far from 0v41 suggests a short or an open on that net; no known-good resistance reading is recorded here.

PP5V_S0_AUDIO_AMP_L0v41––
AI: what PP5V_S0_AUDIO_AMP_L is and how to check it

PP5V_S0_AUDIO_AMP_L — 820-3662

  • What it is: from the name, a 5 V rail feeding the audio amplifier, enabled in the S0 (running) state. The parts on the net aren't known here.
  • Known-good reading: diode 0v41 to ground, from the readings archive. This is a community guide, not a factory spec; no known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0v41. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no voltage points to the rail not being switched on or its source missing. Confirm with a second measurement before replacing anything.
PP5V_S0_AUDIO_AMP_R0.410––
AI: what PP5V_S0_AUDIO_AMP_R is and how to check it
  • What it is: From the name, PP5V_S0_AUDIO_AMP_R is a 5 V rail feeding the audio amplifier, enabled in the S0 (running) state. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.410 to ground, from the community archive (no condition recorded). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; no voltage with power on points to the enable or supply upstream. Treat these as likely causes, not confirmed.
PP5V_S0_BKLT_VDDA0v41––
AI: what PP5V_S0_BKLT_VDDA is and how to check it

PP5V_S0_BKLT_VDDA is a 5 V rail for the backlight section, active in the S0 (running) state — that much comes from the name. The archive lists one known-good reading: diode mode to ground of 0v41, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage is listed here. A diode reading far from 0v41 usually points to a short or a leaky part on that rail, but a single reading doesn't confirm a fault — compare with a matching net or a known-good board before replacing anything.

PP5V_S0_BKLT_VDDD0v41––
AI: what PP5V_S0_BKLT_VDDD is and how to check it

PP5V_S0_BKLT_VDDD — from the name, a 5 V rail (PP5V) that is present in the S0 running state and feeds the backlight circuit (BKLT). The "VDDD" suffix suggests a display-side supply.

  • Known-good diode reading: 0v41 to ground, from the readings archive. This is a community figure and a guide only, not a guaranteed value.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0v41. Then apply power and measure the voltage — it should sit near 5 V once the board is in S0.
  • No known-good voltage reading is recorded here, so compare the powered voltage against the rail's name and a known-good board if one is available.
  • A diode reading far below 0v41 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken path feeding it. Confirm with a second measurement before replacing anything.
PP5V_S0_CPUVR_VDD0.407––
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD is a 5 V rail feeding the CPU voltage-regulator supply, judged from its name; the S0 suffix means it belongs to the running state. The archive lists one known-good reading for this net: diode 0.407, with no condition noted. Check it with the board unpowered in diode mode from the net to ground, then confirm the voltage with power applied; no known-good voltage reading is recorded here. A diode reading far from 0.407 usually points to a short or a damaged component on that rail, but one reading alone doesn't prove a part bad, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S0_KBDLED_R0v41––
AI: what PP5V_S0_KBDLED_R is and how to check it

PP5V_S0_KBDLED_R is a 5 V rail that feeds the keyboard backlight, and the S0 in its name indicates it belongs to the running (S0) state. The readings archive lists one known-good value: diode 0v41, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and confirm about 5 V in the S0 state. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0v41 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.

PP5V_S0_P1V05S0_VCC0.410––
AI: what PP5V_S0_P1V05S0_VCC is and how to check it
  • What it is: From the name, PP5V_S0_P1V05S0_VCC is a 5 V rail that is on in the S0 (running) state and feeds the 1.05 V supply. The name is the only source here; no parts list is available for this board.
  • Known-good reading: diode 0.410 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage, expecting about 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with voltage before replacing anything.
PPBUS_S0_LCDBKLT_FUSED0v46––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it
  • What it is: From the name, PPBUS_S0_LCDBKLT_FUSED is the fused backlight (LCDBKLT) supply derived from PPBUS, active in the S0 (running) state. It feeds the display backlight circuit.
  • Known-good reading: Diode mode to ground is 0v46, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then power up and measure the DC voltage on the net.
  • If far off: A much lower diode reading usually points to a short on that net or its load; a missing voltage with a good diode reading points upstream, toward the fuse or PPBUS. Confirm with a second measurement before replacing anything.
PPBUS_S0_LCDBKLT_PWR_SW0v88––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
  • What it is: From the name, a switched S0 (running-state) power rail feeding the LCD backlight circuit, derived from PPBUS. It's a switched rail, so it may only be present when the backlight is enabled.
  • Known-good reading: Diode mode to ground is 0v88 (community archive value, a guide only). No known-good voltage is recorded here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail, ideally with the display connected and the backlight commanded on.
  • If it's far off: A diode reading well below 0v88 suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to the switch or enable signal. Confirm with a second measurement before replacing anything.
PPVCC_S0_CPU0.013––
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the "S0" in the name indicates it is active in the running state. The archive lists one known-good diode reading of 0.013 to ground, with no condition noted and no voltage reading recorded here.

  • Check with the board unpowered: diode mode, red probe on ground, black probe on PPVCC_S0_CPU.
  • Then power the board and measure the voltage on the same net.
  • No known-good voltage is listed for this rail, so compare against a known-good board of the same model.

A diode reading far from 0.013 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part. This rail is low-resistance by design, so a small difference may be normal.

PPVCC_S0_CPU_PH10.013–18.400R
AI: what PPVCC_S0_CPU_PH1 is and how to check it
  • What it is: PPVCC_S0_CPU_PH1 is a CPU power rail; the S0 in the name indicates the running (S0) state, and PH1 suggests one phase of a multi-phase CPU supply. That reading is from the name only.
  • Known-good readings: diode 0.013 and resistance 18.400R, both from the archive and only a guide, since they vary with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • What a far-off reading suggests: a much higher diode or resistance reading points to an open or missing connection on that phase; a much lower one points to a short on the rail. Confirm with a second measurement before replacing anything.
PPVCC_S0_CPU_PH20.013–18.400R
AI: what PPVCC_S0_CPU_PH2 is and how to check it

PPVCC_S0_CPU_PH2 is a CPU power rail: the "S0" in its name indicates it belongs to the running (S0) state, and "CPU_PH" suggests a CPU supply phase. The archive lists a diode reading of 0.013 and a resistance of 18.400R for it, with no condition noted, so treat these as a guide only. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching phase net or a known-good board. A diode or resistance far from these values usually points to a short or a damaged component on the rail, but confirm with more measurements before replacing anything.

PPVCC_S0_CPU_PH30.013–18.400R
AI: what PPVCC_S0_CPU_PH3 is and how to check it

PPVCC_S0_CPU_PH3 — from the name, a CPU core power phase rail (VCC for the CPU, S0 meaning the board is in its running state). It's one phase of the CPU supply, so expect a very low impedance to ground.

  • Known-good from the archive: diode 0.013 and resistance 18.400R. These are community readings and vary with board state, so treat them as a guide.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, then confirm in resistance mode.
  • With power applied, measure the voltage on the rail; no known-good voltage is recorded here, so compare against a matching phase or a known-good board.
  • A reading far from 0.013 / 18.400R usually points to a short or a failing phase — but one low reading isn't proof, so re-check before replacing anything.
PPVCCIO_S0_CPU0v02––
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is the CPU's I/O supply rail; the S0 in the name indicates it belongs to the running state. The only known-good reading here is a diode value of 0v02 to ground, measured with the board unpowered; no known-good voltage is listed. Check it by taking a diode reading to ground with power off, then measure the voltage on the rail with the board powered and running. A diode reading far from 0v02 usually points to a short or a faulty part on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVCOMP_S0_CPU0.038––
AI: what PPVCOMP_S0_CPU is and how to check it

PPVCOMP_S0_CPU is a CPU compensation rail; the S0 in its name indicates it belongs to the running state. The only known-good reading here is a diode value of 0.038 to ground, with no condition recorded, and no voltage or resistance values are listed. Check it unpowered in diode mode from the net to ground, then measure its voltage with the board powered in S0. A diode reading far from 0.038 usually points to a short or a damaged component on that net, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PPVIN_S0_CPUVR_VIN0.466––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it
  • What it is: From the name, PPVIN_S0_CPUVR_VIN is the input supply to the CPU voltage regulator, active in the S0 (running) state. It's a power input rail, not a switched output.
  • Known-good reading: diode 0.466 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PPVOUT_S0_KBDBKLT0v61––
AI: what PPVOUT_S0_KBDBKLT is and how to check it
  • What it is: From the name, a running-state (S0) output rail feeding keyboard backlight on the 820-3662. The parts and nets on it aren't documented here.
  • Known-good reading: diode 0v61 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from PPVOUT_S0_KBDBKLT to ground and compare with 0v61. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream to the backlight supply or its enable. No voltage value is known here, so compare against a known-good board.
PPVOUT_S0_LCDBKLT1v20––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the "S0" in the name marks it as a running-state rail, and "LCDBKLT" points to the backlight boost output. The only known-good reading here is a diode value of 1v20 to ground, with no condition noted; there is no known-good voltage reading in this data. With the board unpowered, measure diode mode from the rail to ground and compare with 1v20, then power up and check the voltage. A diode reading far below 1v20 usually suggests a short or leaky part on the rail, but a single reading doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PPVOUT_S0_PCH_DCPRTC0.714––
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it
  • What it is: From the name, PPVOUT_S0_PCH_DCPRTC is a power rail (PP = power rail) that is up in the S0 running state, feeding the PCH's DCPRTC domain. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.714 to ground, from the community archive (a guide, not a guarantee). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted part or a shorted load on that rail; a much higher or open reading points to a broken connection. Confirm with the voltage reading before replacing anything.
PPVOUT_S0_PCH_DCPSST0.484––
AI: what PPVOUT_S0_PCH_DCPSST is and how to check it
  • What it is: From the name, PPVOUT_S0_PCH_DCPSST is a power output rail (PPVOUT) active in the S0 running state, feeding the PCH's DCPSST supply. The board data doesn't identify which parts sit on it.
  • Known-good reading: diode 0.484 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with the voltage measurement before replacing anything.
PPVTT_S0_DDR0.096––
AI: what PPVTT_S0_DDR is and how to check it
  • What it is: PPVTT_S0_DDR is a DDR termination rail; the "S0" in the name indicates it is up in the running state. Which parts sit on it isn't known here.
  • Known-good reading: diode 0.096 to ground, from the readings archive (a community guide, not a spec). No known-good voltage is recorded here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure the rail voltage.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open. Confirm with a second measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
4V5_NR0.659––
4V5_REG_EN0.733––
4V5_REG_IN0.443––
ADAPTER_SENSE0.642––
ALL_SYS_PWRGD0.469––
ALL_SYS_PWRGD_ROL––
AP_CLKREQ_L0.445––
AP_CLKREQ_Q_L0v46––
AP_RESET_CONN_L0v46––
AP_RESET_L0.425––
AUD_CONN_HP_LEFT0.660––
AUD_CONN_SLEEVE_XW0.001––
AUD_HP_PORT_L0.660––
AUD_HP_PORT_R0.661––
AUD_HS_MIC_N0.002––
AUD_HS_MIC_P0.001––
AUD_I2C_INT_L0.655––
AUD_IP_PERIPHERAL_DET0.660––
AUD_LO2_L_N0.673––
AUD_LO2_L_P0.673––
AUD_LO2_R_N0.673––
AUD_LO2_R_P0.673––
AUD_LO3_L_N0.659––
AUD_LO3_L_P0.661––
AUD_LO3_R_N0.659––
AUD_LO3_R_P0.660––
AUD_SPKRAMP_LIN_N0.674––
AUD_SPKRAMP_LIN_P0.675––
AUD_SPKRAMP_LSUBIN_N0.660––
AUD_SPKRAMP_LSUBIN_P0.663––
AUD_SPKRAMP_RIN_N0.674––
AUD_SPKRAMP_RIN_P0.675––
AUD_SPKRAMP_RSUBIN_N0.660––
AUD_SPKRAMP_RSUBIN_P0.660––
AUD_TYPEDET0.772––
BKL_1_SCL0v50––
BKL_1_SDA0v50––
BKL_FB0v72––
BKL_FET_CNTL0v50––
BKL_FET_CNTL_R0.548––
BKL_ISEN10v65––
BKL_ISEN20v65––
BKL_ISEN30v65––
BKL_ISEN40v65––
BKL_ISEN50v65––
BKL_ISEN60v65––
BKL_SW0v44––
BKLT_EN_R0v53––
BKLT_EN_R_JERRY0v53––
BKLT_FLT0v73––
BKLT_FLT_RCOL––
BKLT_ISET_KEYB0v66––
BKLT_ISET_LCD0v74––
BKLT_KEYB10v64––
BKLT_KEYB20v64––
BKLT_PWM_KEYB0v54––
BKLT_SCL0v51––
BKLT_SCL_R0v51––
BKLT_SD0.006––
BKLT_SDA0v51––
BKLT_SDA_R0v51––
BKLT_SENSE_OUT0v72––
BKLT_SYNC0v41––
CAM_DEBUG_RESET_L0.777––
CAM_GPIO30.777––
CAM_PCIE_RESET_L0.428––
CAM_PCIE_WAKE_L0.532––
CAM_RAMCFG00.777––
CAM_RAMCFG10.777––
CAM_RAMCFG20.777––
CAM_SENSOR_WAKE_L0.825––
CAM_SENSOR_WAKE_L_CONN0v00––
CAM_TEST_MODE0.774––
CAM_TEST_OUT0.829––
CAM_UARTRXD0.777––
CAM_XTAL_SEL0.778––
CAMERA_CLKREQ_L0.507––
CAMERA_PWR_EN0.544––
CHGR_ACIN0v53––
CHGR_AGATE0v65––
CHGR_AGATE_DIVOL––
CHGR_AMON0v72––
CHGR_BGATE0v66––
CHGR_BMON0v72––
CHGR_BOOT0v59––
CHGR_CELL0v71––
CHGR_CSI_N0v59–21.900R
CHGR_CSI_P0v62–21.900R
CHGR_CSI_R_N0.649––
CHGR_CSI_R_P0.648––
CHGR_CSO_N0v45–3.500R
CHGR_CSO_P0v45–3.500R
CHGR_CSO_R_N0.450––
CHGR_CSO_R_P0.450––
CHGR_DCIN0v59––
CHGR_DCIN_D_R0.607––
CHGR_ICOMP0v72––
CHGR_ICOMP_RC1.734––
CHGR_LGATE0v45––
CHGR_PHASE0v45––
CHGR_RST_L0v51––
CHGR_SGATE0v64––
CHGR_SGATE_DIVOL––
CHGR_UGATE0v89––
CHGR_VCOMP0v72––
CHGR_VCOMP_ROL––
CHGR_VFRQ0v48––
CHGR_VNEG0v53––
CLK25M_CAM_XTALNOL––
CLK25M_CAM_XTALPOL––
CLK25M_CAM_XTALP_ROL––
CODEC_MICIN20.713––
CPU_CATERR_L0.273––
CPU_CFG_RCOMP0.050––
CPU_CFG<0>0v25––
CPU_CFG<1>0v25––
CPU_CFG<2>0v25––
CPU_CFG<3>0v25––
CPU_CFG<4>0v24––
CPU_CFG<5>0v25––
CPU_CFG<6>0v25––
CPU_CFG<7>0v25––
CPU_CFG<8>0v25––
CPU_CFG<9>0v25––
CPU_CFG<10>0v25––
CPU_CFG<11>0v25––
CPU_CFG<12>0v25––
CPU_CFG<13>0v25––
CPU_CFG<14>0v25––
CPU_CFG<15>0v25––
CPU_CFG<16>0v25––
CPU_CFG<17>0v26––
CPU_CFG<18>0v25––
CPU_CFG<19>0v25––
CPU_CLK135M_DPLLREF_N0.292––
CPU_CLK135M_DPLLREF_P0.293––
CPU_CLK135M_DPLLSS_N0.293––
CPU_CLK135M_DPLLSS_P0.294––
CPU_DC_A4OL––
CPU_DC_A51OL––
CPU_DC_BC1OL––
CPU_DC_BC54OL––
CPU_DC_BF4OL––
CPU_DC_BF51OL––
CPU_DC_D1OL––
CPU_DC_D54OL––
CPU_DIMM_VREFCA0.778––
CPU_DIMMA_VREFDQ0.778––
CPU_DIMMB_VREFDQ0.780––
CPU_EDP_RCOMP0.065––
CPU_MEM_RESET_L0.338––
CPU_MEM_VREFCA_A_ISOL0.378––
CPU_MEM_VREFCA_B_ISOL0.375––
CPU_MEM_VREFDQ_A_ISOL0.378––
CPU_MEM_VREFDQ_B_ISOL0.375––
CPU_PECI0.375––
CPU_PECI_R0.334––
CPU_PEG_RCOMP0.063––
CPU_PROCHOT_L0.081––
CPU_PROCHOT_R_L0.135––
CPU_PWR_DEBUG0v21––
CPU_PWRGD0.362––
CPU_RESET_L0.368––
CPU_SM_RCOMP<0>0.104––
CPU_SM_RCOMP<1>–0.076–
CPU_SM_RCOMP<2>0.104––
CPU_TESTLO_F200.052––
CPU_TESTLO_F210.052––
CPU_THRMTRIP_3V30.749––
CPU_VCCSENSE_N0.002––
CPU_VCCSENSE_P0.014––
CPU_VCCSENSE_P_RC1.565––
CPU_VIDALERT_L0.094––
CPU_VIDALERT_R_L0.136––
CPU_VIDSCLK0.071––
CPU_VIDSCLK_R0.075––
CPU_VIDSOUT0.074––
CPU_VIDSOUT_R0.073––
CPUTHMSNS_ALERT_L–3.30–
CPUTHMSNS_D2_N0.7640.70–
CPUTHMSNS_D2_P0.7630.80–
CPUTHMSNS_THM_L0.7613.30–
CPUVDDQ_EN0.559––
CPUVDDQ_EN_L0.598––
CPUVR_BOOT10v57––
CPUVR_BOOT1_RC0.611––
CPUVR_BOOT20v56––
CPUVR_BOOT2_RC0.611––
CPUVR_BOOT30v57––
CPUVR_BOOT3_RC0.611––
CPUVR_COMP0.587––
CPUVR_COMP_RCOL––
CPUVR_DRSEL0.600––
CPUVR_FB_RCOL––
CPUVR_FB20.575––
CPUVR_FCCM0v48––
CPUVR_IMON0.589––
CPUVR_ISEN20.585––
CPUVR_ISEN30.584––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS1_N0.013––
CPUVR_ISNS1_P0.013––
CPUVR_ISNS2_N0.013––
CPUVR_ISNS2_P0.013––
CPUVR_ISNS3_N0.013––
CPUVR_ISNS3_P0.013––
CPUVR_ISUM_IOUT0.592––
CPUVR_ISUM_R_NOL––
CPUVR_ISUM_R_POL––
CPUVR_ISUMN0.014––
CPUVR_ISUMP0.348––
CPUVR_NTC0.598––
CPUVR_NTC_ROL––
CPUVR_PGOOD0.539––
CPUVR_PH1_SNUBOL––
CPUVR_PH2_SNUBOL––
CPUVR_PH3_SNUBOL––
CPUVR_PHASE10.013–18.400R
CPUVR_PHASE1_K0v02––
CPUVR_PHASE20.013–18.400R
CPUVR_PHASE2_K0v02––
CPUVR_PHASE30.013–18.400R
CPUVR_PHASE3_K0v02––
CPUVR_PROG10.590––
CPUVR_PROG20.589––
CPUVR_PROG30.600––
CPUVR_PWM10v51––
CPUVR_PWM20v52––
CPUVR_PWM30v52––
CPUVR_SLOPE0.589––
CPUVSENSE_INOL––
CS4208_HDA_SDOUT0_R0.439––
CS4208_SPDIF_IN0.000––
CS4208_SPDIF_OUT0.692––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S3OL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DBGLED_S5OL––
DCIN_ISOL_GATE0.783––
DCIN_ISOL_GATE_ROL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.502––
DDR3THMSNS_D1_N0.7770.500–
DDR3THMSNS_D1_P0.7800.800–
DDRREG_1V8_VREF0.644––
DDRREG_DRVH0.597––
DDRREG_DRVH_R0.598––
DDRREG_DRVL0.453––
DDRREG_EN0.548––
DDRREG_FB0.692––
DDRREG_LL0.124––
DDRREG_VBST0.622––
DDRREG_VDDQSNS0.124––
DDRREG_VSW0.130––
DDRREG_VTTSNS0.097––
DELAY_1V5S0_PGD0.464––
DFET_CPO10.589––
DFET_CPO20.587––
DFET_OPENCH0.463––
DFET_OPENUS0.463––
DMI_CLK100M_CPU_N0.295––
DMI_CLK100M_CPU_P0.296––
DMI_S2N_N<0>0.291––
DMI_S2N_P<0>0.292––
DMIC_CLK30v77––
DMIC_SDA20v00––
DMIC_SDA30v76––
DP_A_LSX_ML_N<1>0.756––
DP_IG_A_HPD_L0.440––
DP_INT_AUX_NOL––
DP_INT_AUX_POL––
DP_INT_AUXCH_C_N0.302––
DP_INT_AUXCH_C_P0.300––
DP_INT_ML_C_N<0>0.308––
DP_INT_ML_C_N<1>0.306––
DP_INT_ML_C_N<2>0.307––
DP_INT_ML_C_P<0>0.307––
DP_INT_ML_C_P<1>0.308––
DP_INT_ML_C_P<2>0.308––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
DP_TBT_SEL0.542––
DP_TBTPA_AUXCH_C_N0.567––
DP_TBTPA_AUXCH_C_P0.616––
DP_TBTPA_DDC_CLK0v55––
DP_TBTPA_DDC_DATA0v55––
DP_TBTPA_HPD0.774––
DP_TBTPA_ML_C_N<1>0.316––
DP_TBTPA_ML_C_P<1>0.314––
DP_TBTPA_ML_N<1>0.768––
DP_TBTPA_ML_P<1>0.767––
DP_TBTPB_AUXCH_N0.753––
DP_TBTPB_AUXCH_P0.753––
DP_TBTPB_DDC_CLK0v55––
DP_TBTPB_DDC_DATA0v55––
DP_TBTSNK0_AUXCH_C_N0.408––
DP_TBTSNK0_AUXCH_C_P0.410––
DP_TBTSNK0_DDC_CLK0v56––
DP_TBTSNK0_DDC_DATA0v56––
DP_TBTSNK0_HPD0.568––
DP_TBTSNK1_AUXCH_C_N0.406––
DP_TBTSNK1_AUXCH_C_P0.408––
DP_TBTSNK1_DDC_CLK0v56––
DP_TBTSNK1_DDC_DATA0v56––
DP_TBTSNK1_HPD0.570––
EDP_IG_BKL_ON0.548––
EDP_IG_BKL_PWM0.541––
EDP_IG_PANEL_PWR0.654––
ENET_MEDIA_SENSE_RDIV0.412––
FAN_LT_PWM–0.70–
FAN_LT_TACH–1.10–
FAN_RT_PWM–4.00–
FAN_RT_TACH–1.68–
FDI_CSYNC0.378––
FDI_INT0.377––
FINTHMSNS_D_N0.780––
FINTHMSNS_D_P0.787––
FW_PME_L0.700––
G3_POWERON_L0.750––
GND–0.00–
GND_5V3V3_AGND0v00––
GND_BKLT_SGND0v00––
GND_CHGR_AGND0v00––
GND_LCDBKLT_SGND0v00––
GND_TBTBST_SGND0v00––
GPIO0_SPKR_SHUTDOWN0.529––
HDA_BIT_CLK0.463––
HDA_BIT_CLK_R0.424––
HDA_RST_L0.457––
HDA_RST_R_L0.424––
HDA_SDIN00.416––
HDA_SDOUT0.465––
HDA_SDOUT_R0.427––
HDA_SYNC0.465––
HDMI_CLK_N0.305––
HDMI_CLK_P0.305––
HDMI_DATA_N<0>0.304––
HDMI_DATA_N<1>0.306––
HDMI_DATA_N<2>0.308––
HDMI_DATA_P<0>0.305––
HDMI_DATA_P<1>0.305––
HDMI_DATA_P<2>0.307––
HDMI_DDC_CLK0v60––
HDMI_DDC_DATA0v60––
HDMI_HPD0v78––
HDMITBTMUX_SEL_TBT0.610––
HS_COMPUTING_IOUT0.713––
HS_MIC_N2.091––
HS_MIC_P2.060––
HS_OTHER3V3_IOUT0.712––
HS_OTHER5V_IOUT0.711––
I2C_CAM_SCK0v75––
I2C_CAM_SDA0v75––
I2C_CAM_SMBDBG_CLK0.789––
I2C_CAM_SMBDBG_DAT0.789––
ISENSE_P1V35MEM_IOUT0.655––
ISNS_1V35_MEM_N0.125––
ISNS_1V35_MEM_P0.125––
ISNS_1V35_MEM_R_N0.795––
ISNS_1V35_MEM_R_P0.800––
ISNS_AIRPORT_IOUTOL––
ISNS_AIRPORT_R_NOL––
ISNS_AIRPORT_R_POL––
ISNS_CPU_DDR_IOUTOL––
ISNS_CPUDDR_NOL––
ISNS_CPUDDR_POL––
ISNS_HS_COMPUTING_N0.450––
ISNS_HS_COMPUTING_P0.450––
ISNS_HS_OTHER3V3_N0.450––
ISNS_HS_OTHER3V3_P0.450––
ISNS_HS_OTHER5V_N0.450––
ISNS_HS_OTHER5V_P0.450––
ISNS_LCDBKLT_N0v45––
ISNS_LCDBKLT_P0v46––
ISNS_S2_OUTOL––
ISNS_S2_R_NOL––
ISNS_S2_R_POL––
ISNS_SSD_IOUT0.652––
ISNS_SSD_N0.658––
ISNS_SSD_P0.658––
ISNS_SSD_R_N0.799––
ISNS_SSD_R_P0.797––
ISNS_TBT_IOUT0.645––
ISNS_TBT_R_N0.794––
ISOLATE_CPU_MEM_L0.586––
JTAG_ISP_TCK0.500––
JTAG_ISP_TDI0.463––
JTAG_ISP_TDO0.462––
JTAG_TBT_TCK0.565––
JTAG_TBT_TDI0.533––
JTAG_TBT_TDO0.552––
JTAG_TBT_TMS0.532––
JTAG_TBT_TMS_PCH0.470––
KBDBKLT_RETURN10v65––
KBDBKLT_RETURN20v64––
KBDBKLT_SW0v41––
LCD_BKLT_PWM_R0v53––
LCD_FSSOL––
LCD_HPDOL––
LCD_HPD_CONNOL––
LCD_PANEL_IOUTOL––
LCDBKLT_EN_LOL––
LCDBKLT_IOUTOL––
LED_RETURN_10v64––
LED_RETURN_20v64––
LED_RETURN_30v64––
LED_RETURN_40v64––
LED_RETURN_50v64––
LED_RETURN_60v65––
LPC_AD<0>0v54––
LPC_AD<1>0v54––
LPC_AD<2>0v54––
LPC_AD<3>0v54––
LPC_CLK33M_LPCPLUS0v60––
LPC_CLK33M_LPCPLUS_R0.611––
LPC_CLK33M_SMC0.627––
LPC_CLK33M_SMC_R0.604––
LPC_FRAME_L0v54––
LPC_FRAME_R_L0.531––
LPC_PWRDWN_L0v62––
LPC_SERIRQ0v62––
LPCPLUS_GPIO0v62––
LPCPLUS_RESET_L0v57––
LSUBIN_N0.596––
LSUBIN_P0.596––
MEM_A_A<0>0.131––
MEM_A_A<1>0.131––
MEM_A_A<2>0.131––
MEM_A_A<4>0.131––
MEM_A_A<5>0.131––
MEM_A_A<7>0.131––
MEM_A_A<8>0.131––
MEM_A_A<10>0.131––
MEM_A_A<11>0.129––
MEM_A_A<12>0.132––
MEM_A_A<14>0.132––
MEM_A_BA<0>0.129––
MEM_A_BA<1>0.130––
MEM_A_BA<2>0.131––
MEM_A_CAS_L0.130––
MEM_A_CKE<0>0.130––
MEM_A_CKE<1>0.130––
MEM_A_CS_L<0>0.130––
MEM_A_CS_L<1>0.131––
MEM_A_DQ<13>0.268––
MEM_A_DQ<18>0.270––
MEM_A_DQ<21>0.270––
MEM_A_DQ<38>0.262––
MEM_A_DQ<54>0.267––
MEM_A_DQ<55>0.267––
MEM_A_ODT<0>0.130––
MEM_A_ODT<1>0.130––
MEM_B_A<0>0v13––
MEM_B_A<1>0v13––
MEM_B_A<2>0v13––
MEM_B_A<3>0v13––
MEM_B_A<4>0v13––
MEM_B_A<5>0v13––
MEM_B_A<6>0v13––
MEM_B_A<7>0v13––
MEM_B_A<8>0v13––
MEM_B_A<9>0v13––
MEM_B_A<10>0v13––
MEM_B_A<11>0v13––
MEM_B_A<12>0v13––
MEM_B_A<13>0v13––
MEM_B_A<14>0v13––
MEM_B_A<15>0v13––
MEM_B_BA<0>0v13––
MEM_B_BA<1>0v13––
MEM_B_BA<2>0v13––
MEM_B_CAS_L0v13––
MEM_B_CKE<0>0.131––
MEM_B_CKE<1>0v13––
MEM_B_CLK_N<0>0.246––
MEM_B_CLK_N<1>0v25––
MEM_B_CLK_P<0>0.246––
MEM_B_CLK_P<1>0v25––
MEM_B_CLK1_TERM_R0.255––
MEM_B_CS_L<1>0v13––
MEM_B_DQ<0>0v27––
MEM_B_DQ<1>0v27––
MEM_B_DQ<2>0v27––
MEM_B_DQ<3>0v27––
MEM_B_DQ<4>0v27––
MEM_B_DQ<5>0v27––
MEM_B_DQ<6>0v27––
MEM_B_DQ<7>0v27––
MEM_B_DQ<8>0v27––
MEM_B_DQ<9>0v27––
MEM_B_DQ<10>0v27––
MEM_B_DQ<11>0v27––
MEM_B_DQ<12>0v27––
MEM_B_DQ<13>0v27––
MEM_B_DQ<14>0v27––
MEM_B_DQ<15>0v27––
MEM_B_DQ<60>0.269––
MEM_B_DQS_N<0>0v27––
MEM_B_DQS_N<1>0v27––
MEM_B_DQS_P<0>0v27––
MEM_B_DQS_P<1>0v27––
MEM_B_ODT<1>0v13––
MEM_B_RAS_L0v13––
MEM_B_WE_L0v13––
MEM_B_ZQ<8>0v25––
MEM_B_ZQ<9>0v25––
MEM_CAM_A<14>0.468––
MEM_CAM_CKE0.473––
MEM_CAM_CKE_ROL––
MEM_CAM_ODT0.707––
MEM_CAM_RESET_L0.475––
MEM_CAM_WE_L0.470––
MEM_RESET_L0v41––
MEM_VREFCA_A_RC0.026––
MEM_VREFCA_B_RC0.025––
MEM_VREFDQ_A_RC0.026––
MEMPWR_DIVOL––
MEMRESET_ISOL_LS5V_L1.010––
MEMVTT_EN0.547––
MEMVTT_EN_L0.603––
MIPI_CLK_CONN_N0v41––
MIPI_CLK_CONN_P0v41––
MIPI_DATA_CONN_N0v41––
MIPI_DATA_CONN_P0v41––
MLB_RAMCFG00.526––
MLB_RAMCFG20.527––
MLB_RAMCFG30.701––
NCOL––
P1V2_CAM_SRVLXC_PHASE0.321––
P1V5_DIV_VMONOL––
P1V05_EN_D0.858––
P1V05_VID_VMONOL––
P1V05S0_AGND0.000––
P1V05S0_BOOT_RC0.587––
P1V05S0_CS_N0.127––
P1V05S0_CS_P0.127––
P1V05S0_DRVH0v53––
P1V05S0_DRVL0v45––
P1V05S0_EN0.545––
P1V05S0_FB0.521––
P1V5S0_FB0.780––
P1V05S0_FSEL0.544––
P1V05S0_LL0.127––
P1V05S0_OCSET0.523––
P1V05S0_PGOOD0.506––
P1V5S0_PGOOD0.565––
P1V05S0_RTN0.523––
P1V05S0_SENSE_N0.001––
P1V05S0_SENSE_P0.124––
P1V05S0_SREF0.543––
P1V5S0_SW0v30––
P1V05S0_VBST0.586––
P1V05S0_VO0.522––
P1V35_CAM_SRVLXD_PHASE0.258––
P1V35CPU_SLEW_CTL0.727––
P3V3_SSD_EN_L0.506––
P3V3_SSD_SSOL––
P3V3S0_P1V5_S0_EN0.650––
P3V3S3_EN0.502––
P3V3S3_EN_L0.510––
P3V3S3_S4OL––
P3V3S3_SSOL––
P3V3S4_EN_L0.626––
P3V3S5_COMP20v72––
P3V3S5_COMP2_ROL––
P3V3S5_CSN20v14––
P3V3S5_CSP20v76––
P3V3S5_CSP2_R0.147––
P3V3S5_DRVH0v68––
P3V3S5_DRVL0v53––
P3V3S5_EN0v53––
P3V3S5_LL0v14––
P3V3S5_RF0v58––
P3V3S5_SNUBROL––
P3V3S5_TG0.694––
P3V3S5_VBST0v55––
P3V3S5_VFB20v57––
P3V3S5_VFB2_R0.147––
P3V3SSD_VMON0.471––
P3V3SUS_EN_L0.621––
P3V3SUS_SSOL––
P3V3WLAN_VMON0.469––
P3V42G3H_BOOST0.629––
P3V42G3H_FB0.722––
P3V42G3H_SHDN_L0.609––
P3V42G3H_SW0.321––
P5V_DIV_VMONOL––
P5V0S0_EN_L0.635––
P5V0S0_SSOL––
P5V1_BIAS0v32––
P5V1_BOOST0v62––
P5V1_FB0v71––
P5V1_SW0v32––
P5V1_VIN0v59––
P5VP3V3_SKIPSEL0v48––
P5VP3V3_VREF20v48––
P5VP3V3_VREG30v55––
P5VS0_EN0.631––
P5VS3_EN0.499––
P5VS3_EN_L0.617––
P5VS3_SSOL––
P5VS4_COMP10v72––
P5VS4_COMP1_ROL––
P5VS4_CSN10v43––
P5VS4_CSP11v27––
P5VS4_CSP1_R0.440––
P5VS4_DRVH0v95––
P5VS4_DRVL0v53––
P5VS4_EN0v57––
P5VS4_EN_D0.677––
P5VS4_LL0v43––
P5VS4_PGOOD0v57––
P5VS4_TG0.985––
P5VS4_VBST0v62––
P5VS4_VFB10v57––
P5VS4_VFB1_R0.440––
P5VS4_VSW0v43––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.488––
PBUSVSENS_EN_L_DIVOL––
PCA9557D_RESET_L0.585––
PCH_CLK14P3M_REFCLK0.423––
PCH_CLK33M_PCIIN0.632––
PCH_CLK33M_PCIOUT0.609––
PCH_CLK96M_DOT_N0.793––
PCH_CLK96M_DOT_P0.794––
PCH_CLK100M_SATA_N0.796––
PCH_CLK100M_SATA_P0.796––
PCH_CLKIN_GNDN0.793––
PCH_CLKIN_GNDP0.793––
PCH_CLKRQ5_L_GPIO440.608––
PCH_CLKRQ7_L_GPIO460.607––
PCH_DMI_RCOMP0.780––
PCH_DSWVRMEN0.799––
PCH_FDI_RCOMP0.781––
PCH_INTVRMEN_L0.800––
PCH_PCIE_RCOMP0.785––
PCH_PECI0.578––
PCH_PEGCLKRQB_L_GPIO560.599––
PCH_PROCPWRGD0.362––
PCH_RI_L0.663––
PCH_SATA_RCOMP0.781––
PCH_SATALED_L0.652––
PCH_SMBALERT_L0.672––
PCH_SML1ALERT_L0.667––
PCH_SPKR0.548––
PCH_SRTCRST_L0.797––
PCH_STRP_TOPBLK_SWP_L0.467––
PCH_SUSACK_L0.546––
PCH_SUSWARN_L0.546––
PCH_TD_IREF0.792––
PCH_USB_RBIAS0.023––
PCI_INTA_L0.715––
PCI_INTB_L0.712––
PCI_INTC_L0.723––
PCIE_AP_D2R_PI_N0v38––
PCIE_AP_D2R_PI_P0v38––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CAMERA_D2R_N0.380––
PCIE_CAMERA_D2R_P0.380––
PCIE_CLK100M_AP_CONN_N0v30––
PCIE_CLK100M_AP_CONN_P0v30––
PCIE_CLK100M_AP_N0.289––
PCIE_CLK100M_AP_P0.290––
PCIE_CLK100M_CAMERA_N0.293––
PCIE_CLK100M_CAMERA_P0.293––
PCIE_CLK100M_PCH_N0.793––
PCIE_CLK100M_PCH_P0.794––
PCIE_CLK100M_SSD_N0v29––
PCIE_CLK100M_SSD_P0v29––
PCIE_CLK100M_TBT_N0.298––
PCIE_CLK100M_TBT_P0.300––
PCIE_SSD_D2R_N<0>0v37––
PCIE_SSD_D2R_N<1>0v38––
PCIE_SSD_D2R_N<2>0v38––
PCIE_SSD_D2R_N<3>0v38––
PCIE_SSD_D2R_P<0>0v38––
PCIE_SSD_D2R_P<1>0v38––
PCIE_SSD_D2R_P<2>0v38––
PCIE_SSD_D2R_P<3>0v38––
PCIE_SSD_R2D_N<0>OL––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_N<2>OL––
PCIE_SSD_R2D_N<3>OL––
PCIE_SSD_R2D_P<0>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_SSD_R2D_P<2>OL––
PCIE_SSD_R2D_P<3>OL––
PCIE_TBT_D2R_N<2>0.317––
PCIE_TBT_D2R_N<3>0.313––
PCIE_TBT_D2R_P<2>0.318––
PCIE_TBT_D2R_P<3>0.312––
PCIE_TBT_R2D_C_N<0>0.308––
PCIE_TBT_R2D_C_N<1>0.308––
PCIE_TBT_R2D_C_P<1>0.309––
PCIE_WAKE_L0v54––
PD_CS4208_GPIO10.742––
PDCINVSENS_EN_L_DIVOL––
PICKB_L0v67––
PLT_RESET_L0.585––
PLT_RST_BUF_L0.425––
PM_1V5_PGD_LOL––
PM_1V5_PGD_L_ROL––
PM_BATLOW_L0.523––
PM_CLK32K_SUSCLK_R0.713––
PM_CLKRUN_L0v53––
PM_DSW_PWRGD0.745––
PM_MEM_PWRGD0.450––
PM_MEM_PWRGD_LOL––
PM_P1V5_PGD_DIVOL––
PM_PCH_PWROK0.676––
PM_PCH_SYS_PWROK0.740––
PM_PWRBTN_L0.611––
PM_RSMRST_L0.633––
PM_S0_PGOOD0.676––
PM_SLP_S3_BUF_L0v62––
PM_SLP_S3_L0.516––
PM_SLP_S3_R_L0.449––
PM_SLP_S4_L0.500––
PM_SLP_S5_L0.628––
PM_SLP_SUS_L0.682––
PM_SYNC0.376––
PM_SYSRST_L0.637––
PM_THRMTRIP_B_LOL––
PM_THRMTRIP_L0.268––
PM_THRMTRIP_L_R0.570––
PM_WLAN_EN0.438––
PP0V75_S3_MEM_VREFCA_A0.376––
PP0V75_S3_MEM_VREFCA_B0v38––
PP0V75_S3_MEM_VREFDQ_A0.376––
PP0V75_S3_MEM_VREFDQ_B0v38––
PP0V675_CAM_VREF0.673––
PP0V675_MEM_CAM_VREFCA0.520––
PP0V675_MEM_CAM_VREFDQ0.673––
PP1V2_CAM0.322––
PP1V2_CAM_PCIE_PVDD_FLT0.353––
PP1V2_CAM_PCIE_VDD_FLT0.353––
PP1V2_CAM_XTALPCIEVDD0.353––
PP1V2_S5_SMC_VDDC0.524––
PP1V05_S00.127––
PP1V5_S00v30––
PP1V5_S0_AUDIO_DIG0.346––
PP1V05_S0_PCH_VCC_CLK_F0.125––
PP1V05_S0_PCH_VCC_CLK_R0.124––
PP1V05_S0_REG_R0.127––
PP1V05_SUS0.350––
PP1V05_TBT0.169––
PP1V05_TBTCIO0.115––
PP1V05_TBTRDV0.129––
PP1V5R1V35_S0_RIO0.345––
PP1V8_CAM0.511––
PP1V35_CAM0.255––
PP1V35_DDR_CLK0.255––
PP1V35_S30.125––
PP1V35_S3_MEM0.125––
PP1V35_S3RS0_CPUDDR0.136––
PP1V35_S3RS0_FET0.137––
PP3V3_S00v343.30–
PP3V3_S0_AUDIO_ANALOG0.358––
PP3V3_S0_CPUTHMSNS_R0.4053.30–
PP3V3_S0_FINTHMSNS_R0.403––
PP3V3_S0_VMON_P2OL––
PP3V3_S0_VMON_P7OL––
PP3V3_S0SW_SSD0.657––
PP3V3_S0SW_SSD_FLT0v64––
PP3V3_S0SW_SSD_R0.657––
PP3V3_S30v45––
PP3V3_S3_FAN_CTL–3.30–
PP3V3_S3_PSOC0v40––
PP3V3_S3_VREFMRGN0.509––
PP3V3_S3RS0_CAMERA0.357––
PP3V3_S3RS0_CAMERA_R0.357––
PP3V3_S3RS4_BT_F0v41––
PP3V3_S40v40––
PP3V3_S4_TBT0.413––
PP3V3_S4_TBT_F0.412––
PP3V3_S4_TBTAPWR0.375––
PP3V3_S4_TBTBPWR0.372––
PP3V3_S50v14––
PP3V3_S5_AVREF_SMC0.609––
PP3V3_S5_DBGLEDOL––
PP3V3_S5_SMC_VDDA0.320––
PP3V3_SUS0v33––
PP3V3_TBTLC0.419––
PP3V3_TBTRDV0.549––
PP3V3_TPAD_CONN0v39––
PP3V3_WLAN0.544––
PP3V3_WLAN_F0.544––
PP3V3_WLAN_R0.544––
PP3V3RHV_S4_TBTAPWR0.559––
PP3V3RHV_S4_TBTAPWR_F0.559––
PP3V3RHV_S4_TBTBPWR0.561––
PP3V3RHV_S4_TBTBPWR_F0.560––
PP3V42_G3H0v32––
PP3V42_G3H_SMC_SPVSR0.318––
PP4V5_AUDIO_ANALOG0.421––
PP5V_S00v415.00–
PP5V_S0_AUDIO_AMP_L0v41––
PP5V_S0_AUDIO_AMP_R0.410––
PP5V_S0_BKLT_VDDA0v41––
PP5V_S0_BKLT_VDDD0v41––
PP5V_S0_CPUVR_VDD0.407––
PP5V_S0_KBDLED_R0v41––
PP5V_S0_P1V05S0_VCC0.410––
PP5V_S30.493––
PP5V_S3_LTUSB_A_F0.525––
PP5V_S3_LTUSB_A_ILIM0.524––
PP5V_S3RS0_ALSCAM_F0v41––
PP5V_S40v43––
PP5V_S4_AUDIO_XW0.430––
PP5V_S50v46––
PP5V_S5_CUMULUS0v46––
PP5V1_CHGR_VDD0v32––
PP5V1_CHGR_VDDP0v32––
PP5VR3V3_SW_LCD0.650––
PP5VR3V3_SW_LCD_ISNS0.617––
PP5VR3V3_SW_LCD_UF0.650––
PP15V_TBT0v56––
PP20V_DCIN_CONN_ROL––
PP20V_DCIN_FUSEOL––
PPBUS_G3H0v45––
PPBUS_G3H_R0.471––
PPBUS_S0_LCDBKLT_FUSED0v46––
PPBUS_S0_LCDBKLT_PWR_SW0v88––
PPBUS_SW_BKL0v88––
PPBUS_SW_LCDBKLT_PWR0v46––
PPDCIN_G3H0v68––
PPDCIN_G3H_CHGR0v63––
PPDCIN_G3H_INRUSH0v63––
PPDCIN_G3H_ISOLOL––
PPVBAT_G3H_CHGR_R0.450––
PPVBAT_G3H_CHGR_REG0v45––
PPVBAT_G3H_CONNOL––
PPVCC_S0_CPU0.013––
PPVCC_S0_CPU_PH10.013–18.400R
PPVCC_S0_CPU_PH20.013–18.400R
PPVCC_S0_CPU_PH30.013–18.400R
PPVCCIO_S0_CPU0v02––
PPVCOMP_S0_CPU0.038––
PPVIN_G3H_P3V42G3H0.609––
PPVIN_S0_CPUVR_VIN0.466––
PPVIN_S5_HS_COMPUTING_ISNS0.450––
PPVIN_S5_HS_OTHER3V3_ISNS0v45––
PPVIN_S5_HS_OTHER5V_ISNS0v45––
PPVIN_SW_TBTBST0v51––
PPVOUT_BKLT_FB20v61––
PPVOUT_S0_KBDBKLT0v61––
PPVOUT_S0_LCDBKLT1v20––
PPVOUT_S0_PCH_DCPRTC0.714––
PPVOUT_S0_PCH_DCPSST0.484––
PPVOUT_S5_PCH_DCPSUSBYP_R0.393––
PPVRTC_G3H0.446––
PPVTT_S0_DDR0.096––
PPVTTDDR_S30.489––
PSOC_F_CS_L0v70––
PSOC_MISO0v70––
PSOC_MOSI0v70––
PSOC_SCLK0v70––
RIO_SDCONN_STATE_CHANGE_L0v70––
RSUB_GAIN0.589––
RSUBIN_N0.593––
RSUBIN_P0.593––
RTC_RESET_L0.796––
S0PGD_BJT_GND_R0.101––
S0PGD_COL––
S4_PWR_EN0.454––
S5_PWRGD0v57––
SD_PWR_EN0v52––
SD_SEL_PCIE_L_USB_H0.704––
SDCONN_STATE_CHANGE_L0.505––
SMBUS_PCH_CLK0v49––
SMBUS_PCH_DATA0v49––
SMBUS_SMC_0_S0_SCL0v71––
SMBUS_SMC_0_S0_SDA0v71––
SMBUS_SMC_1_S0_SCL–3.30–
SMBUS_SMC_1_S0_SDA–3.30–
SMBUS_SMC_2_S3_SCL0v72––
SMBUS_SMC_2_S3_SDA0v72––
SMBUS_SMC_5_G3_SCL0v52––
SMBUS_SMC_5_G3_SDA0v52––
SMC_ADAPTER_EN0.613––
SMC_BC_ACOK0v53––
SMC_BC_ACOK_VCC0.597––
SMC_BIL_BUTTON_L0.750––
SMC_CHGR_BMON_ISENSE0.748––
SMC_CLK32K0.718––
SMC_CPU_HI_ISENSE0.748––
SMC_CPUPKG_ISENSE0.592––
SMC_CPUPKG_VSENSE0.741––
SMC_DCIN_ISENSE0.747––
SMC_DCIN_VSENSE0.739––
SMC_DEBUGPRT_EN_L0.587––
SMC_DEBUGPRT_RX_L0.690––
SMC_DEBUGPRT_TX_L0.690––
SMC_DELAYED_PWRGD0.709––
SMC_DP_HPD_L0.752––
SMC_EXTAL0.780––
SMC_FAN_0_CTL–0.85–
SMC_FAN_1_CTL–2.31–
SMC_FAN_1_TACH0.751––
SMC_LCDBKLT_ISENSE0.747––
SMC_LCDPANEL_ISENSE0.749––
SMC_LID0.507––
SMC_LID_R0.501––
SMC_LRESET_L0.611––
SMC_MANUAL_RST_L0.678––
SMC_ONOFF_L0.670––
SMC_OOB1_D2R_CONN_L0v70––
SMC_OOB1_D2R_L0.690––
SMC_OOB1_R2D_CONN_L0v68––
SMC_OOB1_R2D_L0.689––
SMC_OTHER3V3_HI_ISENSE0.748––
SMC_P1V35MEM_ISENSE0.749––
SMC_PBUS_VSENSE0.745––
SMC_PECI_L0.744––
SMC_PECI_L_R0.744––
SMC_PM_G2_EN0v53––
SMC_PME_S4_DARK_L0.637––
SMC_PME_S4_WAKE_L0.493––
SMC_PME_SDCONN0.628––
SMC_PROCHOT0.751––
SMC_PWRFAIL_WARN_L0v68––
SMC_RESET_L0v51––
SMC_ROMBOOT1v30––
SMC_RUNTIME_SCI_L0.665––
SMC_RX_L0v74––
SMC_S4_WAKESRC_EN0.703––
SMC_S5_PWRGD_VIN0.754––
SMC_SSD_ISENSE0.744––
SMC_SYS_KBDLED0.563––
SMC_TBT_ISENSE0.740––
SMC_TCK0v74––
SMC_TDI0v74––
SMC_TDO0v74––
SMC_THRMTRIP0.751––
SMC_TMS0v74––
SMC_TOPBLK_SWP_L0.736––
SMC_TX_L0v74––
SMC_VCCIO_CPU_DIV20.740––
SMC_WAKE_L0.751––
SMC_WAKE_SCI_L0.521––
SMC_X29_ISENSE0.751––
SMC_XTAL0.767––
SMC_XTAL_ROL––
SML_PCH_1_CLK0.560––
SML_PCH_1_DATA0.560––
SMS_INT_L0.753––
SPDIF_OUT_JACK0.678––
SPI_ALT_CLK0v60––
SPI_ALT_CS_L0v54––
SPI_ALT_MISO0v48––
SPI_ALT_MOSI0v51––
SPI_CLK0.609––
SPI_CS0_L0.544––
SPI_DESCRIPTOR_OVERRIDE1.340––
SPI_DESCRIPTOR_OVERRIDE_L0.754––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.617––
SPI_IO<3>0.548––
SPI_MISO0.495––
SPI_MLB_CLK0v61––
SPI_MLB_CS_L0v54––
SPI_MLB_MISO0v49––
SPI_MLB_MOSI0v51––
SPI_MOSI0.541––
SPI_SMC_CLK0.609––
SPI_SMC_CS_L0.538––
SPI_SMC_MISO0.508––
SPI_SMC_MOSI0.548––
SPIROM_HOLD_L0v51––
SPIROM_USE_MLB0v48––
SPIROM_WP_L0v63––
SPKR_L_GAIN0.622––
SPKR_R_GAIN0.623––
SPKR_SHUTDOWN0.528––
SPKRAMP_LIN_N0.620––
SPKRAMP_LIN_P0.620––
SPKRAMP_RIN_N0.620––
SPKRAMP_RIN_P0.620––
SPKRCONN_L_ID0v72––
SPKRCONN_L_OUT_N0v53––
SPKRCONN_L_OUT_P0v52––
SPKRCONN_R_ID0v72––
SPKRCONN_R_OUT_N0v53––
SPKRCONN_R_OUT_P0v52––
SPKRCONN_SL_OUT_N0v61––
SPKRCONN_SL_OUT_P0v61––
SPKRCONN_SR_OUT_N0v61––
SPKRCONN_SR_OUT_P0v61––
SSD_CLKREQ_CONN_L0v46––
SSD_CLKREQ_L0.440––
SSD_DEVSLP2v14––
SSD_PCIE_SEL_L0v49––
SSD_PWR_EN0.455––
SSD_PWR_FET_EN0v44––
SSD_RESET_CONN_L0v46––
SSD_RESET_L0.425––
SUS_PGOOD_CT0.640––
SYS_DETECT_L2v14––
SYS_ONEWIRE0.685––
SYS_PWROK_R0.687––
SYSCLK_CLK25M_CAMERA0.452––
SYSCLK_CLK25M_SB0.430––
SYSCLK_CLK25M_SB_R0.561––
SYSCLK_CLK25M_TBT0.443––
SYSCLK_CLK25M_TBT_R0.671––
SYSCLK_CLK25M_X10.445––
SYSCLK_CLK25M_X20.448––
SYSCLK_CLK25M_X2_R0.448––
SYSCLK_CLK32K_RTC0.455––
TBT_A_CIO_SEL0.802––
TBT_A_CONFIG1_BUF0.776––
TBT_A_CONFIG1_RC0.843––
TBT_A_CONFIG2_RC0.814––
TBT_A_D2R_N<1>0.390––
TBT_A_D2R_P<1>0.391––
TBT_A_DP_PWRDN0.797––
TBT_A_HPD0.841––
TBT_A_HV_EN0.481––
TBT_A_LSTX0.762––
TBT_A_R2D_C_P<1>0.227––
TBT_B_CONFIG1_RC0.843––
TBT_B_CONFIG2_RC0.807––
TBT_B_DP_PWRDN0.798––
TBT_B_HPD0.842––
TBT_B_HV_EN0v48––
TBT_BATLOW_L0.801––
TBT_CIO_PLUG_EVENT_L0.500––
TBT_CLKREQ_L0.491––
TBT_DDC_XBAR_EN0v49––
TBT_DDC_XBAR_EN_L0v80––
TBT_EN_CIO_PWR_L0.567––
TBT_MONOBSN0.187––
TBT_MONOBSP0.187––
TBT_PCIE_RESET_L0.431––
TBT_POC_RESET_L0.660––
TBT_PWR_EN0.673––
TBT_PWR_EN_PCH0.647––
TBT_PWR_ON_POC_RST_L0.737––
TBT_PWR_REQ_L0.712––
TBT_RBIAS0.795––
TBTACONN_1_COL––
TBTACONN_7_COL––
TBTACONN_20_RC0.573––
TBTAPWRSW_ISET_S00.479––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.478––
TBTAPWRSW_ISET_V3P30.479––
TBTBCONN_1_COL––
TBTBCONN_7_COL––
TBTBCONN_20_RC0.572––
TBTBPWRSW_ISET_S00.477––
TBTBPWRSW_ISET_S30.477––
TBTBPWRSW_ISET_V3P30.477––
TBTBST_BOOST0v51––
TBTBST_EN_UVLO0v61––
TBTBST_FBX2v27––
TBTBST_INTVCC0v57––
TBTBST_PWREN_DIV_LOL––
TBTBST_PWREN_L0v49––
TBTBST_RT0v67––
TBTBST_SHDN_DIV0.626––
TBTBST_SNS10v00––
TBTBST_SNS20v00––
TBTBST_SS0v67––
TBTBST_VC0v68––
TBTBST_VC_RCOL––
TBTBST_VSNS0.569––
TBTDP_AUXIO_EN0.788––
TBTPOCRST_CT0.736––
TBTPOCRST_SENSE1.414––
TP_CAM_JTAG_TCK0.778––
TP_CAM_JTAG_TDI0.779––
TP_CAM_JTAG_TDO0.778––
TP_CAM_JTAG_TMS0.779––
TP_CAM_JTAG_TRST_L0.779––
TP_CAM_LV_JTAG_TCK0.777––
TP_CAM_LV_JTAG_TDI0.777––
TP_CAM_LV_JTAG_TDO0.778––
TP_CAM_LV_JTAG_TMS0.777––
TP_CAM_LV_JTAG_TRSTN0.778––
TP_CAM_TEST_MODE10.777––
TP_CAM_TEST_MODE20.778––
TP_CPU_FC_VCCST_PWRGDOL––
TP_CPU_IVR_ERROR0.272––
TP_CPU_RSVD_TP780.270––
TP_EDP_DISP_UTIL0.378––
TP_ISSP_SCLK_P1_10v70––
TP_ISSP_SDATA_P1_00v70––
TP_P7_70v70––
TP_PEG_D2RN<4>0.311––
TP_PEG_D2RN<5>0.312––
TP_PEG_D2RN<6>0.311––
TP_PEG_D2RN<7>0.310––
TP_PEG_D2RN<8>0.311––
TP_PEG_D2RN<9>0.310––
TP_PEG_D2RN<10>0.311––
TP_PEG_D2RN<11>0.311––
TP_PEG_D2RP<4>0.312––
TP_PEG_D2RP<5>0.312––
TP_PEG_D2RP<6>0.311––
TP_PEG_D2RP<7>0.312––
TP_PEG_D2RP<8>0.311––
TP_PEG_D2RP<9>0.312––
TP_PEG_D2RP<10>0.312––
TP_PEG_D2RP<11>0.309––
TP_PSOC_P1_30v70––
TP_PSOC_SCL0v70––
TP_PSOC_SDA0v70––
TP_SMC_MD1OL––
TP_SMC_MPM5_LED_CHG0.751––
TP_SMC_TRST_LOL––
TP_SUS_PGOOD_MR_L0.700––
TP_TDM_ONEWIRE_MPMOL––
TPAD_VBUS_EN0v69––
UNCONNECTED_6OL––
UNCONNECTED_7OL––
UNCONNECTED_8OL––
UNCONNECTED_9OL––
UNCONNECTED_10OL––
UNCONNECTED_11OL––
UNCONNECTED_12OL––
UNCONNECTED_130v70––
UNCONNECTED_140v70––
UNCONNECTED_150v70––
UNCONNECTED_27OL––
UNCONNECTED_28OL––
UNCONNECTED_1770v62––
UNCONNECTED_1780v43––
UNCONNECTED_1790v61––
UNCONNECTED_1800v00––
UNCONNECTED_1810v62––
UNCONNECTED_1820v45––
UNCONNECTED_1830v61––
UNCONNECTED_1840v02––
UNCONNECTED_1850v62––
UNCONNECTED_1860v44––
UNCONNECTED_1870v62––
UNCONNECTED_1880v02––
UNCONNECTED_202OL––
UNCONNECTED_203OL––
UNCONNECTED_445OL––
UNCONNECTED_447OL––
UNCONNECTED_448OL––
UNCONNECTED_449OL––
UNCONNECTED_450OL––
UNCONNECTED_451OL––
UNCONNECTED_452OL––
UNCONNECTED_453OL––
UNCONNECTED_454OL––
UNCONNECTED_455OL––
UNCONNECTED_456OL––
UNCONNECTED_457OL––
UNCONNECTED_458OL––
UNCONNECTED_459OL––
UNCONNECTED_460OL––
UNCONNECTED_461OL––
UNCONNECTED_462OL––
UNCONNECTED_463OL––
UNCONNECTED_464OL––
UNCONNECTED_465OL––
UNCONNECTED_466OL––
UNCONNECTED_473OL––
UNCONNECTED_532OL––
UNCONNECTED_5370v52––
UNCONNECTED_5380v52––
UNCONNECTED_541–0.00–
UNCONNECTED_544–0.00–
UNCONNECTED_553OL––
USB_BT_CONN_N0v65––
USB_BT_CONN_P0v64––
USB_BT_N0.476––
USB_BT_P0.478––
USB_BT_WAKEN0.691––
USB_EXTA_MUXED_N0.672––
USB_EXTA_MUXED_P0.669––
USB_EXTA_N0.465––
USB_EXTA_OC_L0.503––
USB_EXTA_P0.468––
USB_EXTB_N0.465––
USB_EXTB_OC_L0v52––
USB_EXTB_P0.464––
USB_ILIM0.552––
USB_LT1_N0.675––
USB_LT1_P0.672––
USB_PWR_EN0.498––
USB_TPAD_N0.446––
USB_TPAD_P0.458––
USB_TPAD_R_N0v46––
USB_TPAD_R_P0v46––
USB3_EXTA_D2R_N0.378––
USB3_EXTA_D2R_P0.380––
USB3_EXTB_D2R_N0.395––
USB3_EXTB_D2R_P0.396––
USB3_EXTB_R2D_C_N0.372––
USB3_EXTB_R2D_C_P0.371––
USB3_EXTB_R2D_NOL––
USB3_EXTB_R2D_POL––
USB3_SD_D2R_N0.376––
USB3_SD_D2R_P0.377––
USB3_SD_R2D_C_N0.372––
USB3_SD_R2D_C_P0.370––
VMON_3V3_DIVOL––
VMON_5V_DIVOL––
VMON_MROL––
VMON_Q2_BASEOL––
VMON_Q3_BASE1.152––
VMON_Q4_BASEOL––
VREFMRGN_CA_A_ENOL––
VREFMRGN_CA_A_EN_RCOL––
VREFMRGN_CA_A_RDIVOL––
VREFMRGN_CA_ABOL––
VREFMRGN_CA_B_ENOL––
VREFMRGN_CA_B_EN_RCOL––
VREFMRGN_CA_B_RDIVOL––
VREFMRGN_DQ_A_ENOL––
VREFMRGN_DQ_A_EN_RCOL––
VREFMRGN_DQ_A_RDIVOL––
VREFMRGN_DQ_B_ENOL––
VREFMRGN_DQ_B_EN_RCOL––
VREFMRGN_DQ_B_RDIVOL––
VREFMRGN_FRAMEBUF_BUFOL––
VREFMRGN_FRAMEBUF_ENOL––
VREFMRGN_MEMVREG_BUFOL––
VREFMRGN_MEMVREG_ENOL––
VREFMRGN_MEMVREG_FBVREFOL––
VTTCLAMP_EN0.620––
VTTCLAMP_L0.106––
WIFI_EVENT_L0v73––
WOL_EN0.576––
WS_CONTROL_KBD0v47––
WS_CONTROL_KEY0v47––
WS_KBD_ONOFF_L1v22––
WS_KBD10v70––
WS_KBD20v70––
WS_KBD30v70––
WS_KBD40v70––
WS_KBD50v70––
WS_KBD60v70––
WS_KBD70v70––
WS_KBD80v70––
WS_KBD90v70––
WS_KBD100v70––
WS_KBD110v70––
WS_KBD120v70––
WS_KBD130v70––
WS_KBD140v70––
WS_KBD15_C0v70––
WS_KBD15_CAP0v78––
WS_KBD16_NUM0v68––
WS_KBD16N0v70––
WS_KBD170v67––
WS_KBD180v67––
WS_KBD190v66––
WS_KBD200v70––
WS_KBD210v70––
WS_KBD220v70––
WS_KBD230v70––
WS_LEFT_OPTION_KBD0v47––
WS_LEFT_OPTION_KEY0.475––
WS_LEFT_SHIFT_KBD0v47––
WS_LEFT_SHIFT_KEY0.475––
X29THMSNS_A00.677––
XDP_BPM_L<0>0v25––
XDP_BPM_L<1>0v25––
XDP_BPM_L<2>0.271––
XDP_BPM_L<3>0.270––
XDP_BPM_L<4>0.269––
XDP_BPM_L<5>0.270––
XDP_BPM_L<6>0.272––
XDP_BPM_L<7>0.272––
XDP_CPU_PRDY_L0v26––
XDP_CPU_PREQ_L0v26––
XDP_CPU_PRESENT_L0v95––
XDP_CPU_PWRBTN_L0v58––
XDP_CPU_TCK0v06––
XDP_CPU_TDI0.266––
XDP_CPU_TMS0.265––
XDP_CPU_VCCST_PWRGD1v02––
XDP_CPUPCH_TRST_L0.052––
XDP_CPURST_L1v15––
XDP_DA1_USB_EXTC_OC_L0.547––
XDP_DA2_SSD_PWR_EN0.456––
XDP_DA3_CAMERA_PWR_EN0.545––
XDP_DB0_USB_EXTB_OC_L0.553––
XDP_DB1_USB_EXTD_OC_L0.552––
XDP_DB2_SD_PWR_EN0.549––
XDP_DB3_SDCONN_STATE_CHANGE_L0.504––
XDP_DBRESET_L0v61––
XDP_DC0_DP_AUXCH_ISOL_L0.511––
XDP_DC2_ODD_PWR_EN_L0.535––
XDP_DC3_JTAG_ISP_TCK0.502––
XDP_DD1_MLB_RAMCFG10.456––
XDP_DD2_ENETSD_CLKREQ_L0.539––
XDP_FC0_HDD_PWR_EN0.518––
XDP_FC1_GPU_GOOD0.537––
XDP_JTAG_CPU_ISOL_L0.609––
XDP_PCH_TCK0v06––
XDP_PCH_TDI0v37––
XDP_PCH_TDO0v37––
XDP_PCH_TMS0v37––
XDP_SYS_PWROK0v73––
XDP_TRST_L0v61––
Z2_CLKIN0v70––
Z2_CS_L0v70––
Z2_HOST_INTN0v69––
Z2_KEY_ACT_L0v70––
Z2_MISO0v69––
Z2_MOSI0v70––
Z2_SCLK0v69––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3662?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3662: diode 0v45. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3662?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3662: diode 0v32. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3662?

OpenBoardData's known-good values for PP5V_S5 on the 820-3662: diode 0v46. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3662 board?

Open your own 820-3662 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License