Apple laptop board · OpenBoardData

820-00165 known-good readings

Known-good readings for the Apple laptop board 820-00165: 1,259 nets, including 104 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 103 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00165.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 104 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.3200.300 TP+and+KB+Installed3.40.300R
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail at the G3 stage (G3H means always on, from the name). Known-good readings here: diode 0.320 to ground, diode 0.300 with TP and keyboard installed, voltage 3.4 V, resistance 0.300R. Check it unpowered in diode mode to ground, then power up and measure the voltage. A voltage well off 3.4 V, or a diode reading far from 0.300–0.320, usually points to a short or a failed source on that rail; no known-good value of other kinds is listed here.

PP3V42_G3H_SMC_SPVSR0.32––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR — reference note

  • This is a 3.42 V always-on G3H rail feeding the SMC's SPVSR input; the G3H and SMC parts of the name indicate it should be present as soon as the charger is connected, before any power-on.
  • Known-good: diode reading 0.32 to ground, board unpowered. No known-good voltage reading is recorded for this net here.
  • To check it: power off and disconnect the charger, measure diode mode from the net to ground, then apply a genuine MagSafe 2 brick and measure the voltage. The overview notes stress using a genuine brick, or you can end up chasing a no-boot fault.
  • A diode reading far below 0.32 suggests a short or leaky load on the rail; far above it suggests an open path. A missing or low voltage with a normal diode reading points upstream, toward the charger-side G3H supply rather than the SMC.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PPBUS_G3H0.13 1.8GHz i5 8GB0.1288.600–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the G3H suffix, from the name, marks it as an always-on rail present from the G3 state. Known-good readings here are diode 0.13 (recorded on a 1.8GHz i5 8GB board) and diode 0.128, with 8.600 V measured with power applied; the power sequence notes also give about 8.2 V before the SMC runs and 8.56 V once it asserts. Check it with the board unpowered in diode mode from PPBUS_G3H to ground, then power up with a genuine MagSafe 2 brick and measure the voltage. A diode reading far below known-good suggests a short on the rail; a voltage far off 8.2–8.6 V points to the charger/DC-in side or the SMC not running, though one reading alone doesn't confirm a bad part. No known-good resistance value is recorded for this rail.

PPBUS_G3H_R0.148.600–
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main G3H (always-on) bus rail; the "G3H" part of the name indicates it should be present whenever the charger is connected, before the board is switched on. Known-good readings here are diode 0.14 in diode mode and 8.600 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.14 or a voltage well off 8.600 V usually points to a short or a fault on the bus or its source, but one reading alone doesn't confirm a bad part. No known-good resistance reading is listed for this rail.

PPDCIN_G3H1.98816.500–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H — the "G3H" suffix marks it as an always-on rail (from the name), the main adapter input after the MagSafe/charger front end.

  • Known-good readings here: diode 1.988 to ground, voltage 16.500 V with a genuine adapter connected (no condition noted beyond that).
  • Check it unpowered first: diode mode, black probe on ground, red on the rail. Then power up with a genuine MagSafe 2 brick and measure the voltage.
  • A diode reading far below known-good suggests a short or leaky part on the rail; a voltage well under 16.5 V points back toward the adapter, MagSafe connector or charger input side rather than the rail itself.
  • No known-good resistance reading for this rail is recorded here.
PPDCIN_G3H_CHGR0.60016.500–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR — the "G3H" in the name marks it as an always-on startup-stage rail, and "CHGR" points to the charger section; that reading is from the name, not a schematic.

  • Known-good from the archive: diode 0.600 to ground, and 16.500 V with a genuine adapter connected (the G3 sequence note gives 16.5–20 V for Pro-style adapters).
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power up with a genuine MagSafe 2 brick and measure the voltage.
  • A diode reading well below 0.600 suggests a short or leaky part on the rail; a voltage far under 16.5 V points back toward the adapter, the DC-in path or the charger circuit.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board.
PPDCIN_G3H_INRUSH0.60016.500–
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is an early adapter-input rail; the G3H suffix (from the name) means it's always-on whenever the adapter is connected, and "inrush" suggests it feeds the initial charging of the input capacitors. Known-good readings here are diode 0.600 to ground and 16.500 V with the adapter connected. Check it unpowered in diode mode from the rail to ground, then measure the voltage with a genuine MagSafe 2 adapter attached. A diode reading far below 0.600 suggests a short or leaky part on that rail; a voltage well under 16.5 V points to a problem upstream in the adapter input path. No known-good resistance reading exists for this rail.

PPDCIN_G3H_ISOLol16.500150K
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is an always-on G3 rail derived from the adapter input, per the "G3H" in its name. Known-good readings here: diode OL, voltage 16.500 V, resistance 150K (community values, a guide only). Check it with the board unpowered in diode mode to ground, then measure the voltage with a genuine MagSafe 2 adapter connected. A voltage far below 16.5 V points to the adapter input path or isolation gate rather than this rail itself; no known-good value exists for other conditions.

PPVBAT_G3H_CHGR_R0.138.600–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — a G3H (always-on) rail feeding the charger's battery path, judging from the name; the data doesn't list which parts sit on it.

  • Known-good from the archive: diode 0.13 to ground, voltage 8.600 (no condition recorded).
  • Check with the board unpowered and the battery disconnected: meter in diode mode, black probe on ground, red on the rail. Then apply power and read the voltage.
  • A diode reading well below 0.13 suggests a partial short on that rail; a much higher one or OL suggests an open path. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_REG0.13 1.8GHz i5 8GB0.1308.6003.000k
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG — the name marks it as a G3H (always-on) charger-side rail, likely the charger's battery/regulation reference; that's from the name, not from board data.

Known-good readings from the archive: diode 0.13 and 0.130 (one on a 1.8GHz i5 8GB board), voltage 8.600, resistance 3.000k. No condition is recorded for these, so treat them as a guide only.

To check it: power off and unplug, then diode-mode from the rail to ground; with power applied, measure the voltage. A diode far below ~0.13 suggests a short on that rail; a voltage well off 8.6V points to the charger circuit or its supply rather than the rail itself. No known-good value of another kind is recorded here, so compare against a matching rail or a known-good board.

PPVBAT_G3H_CONNOL––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-backed G3H rail at the battery connector; the G3H suffix, from the name, means it should be present whenever the adapter is connected, before the board powers up.

  • Known-good reading here: diode mode to ground reads OL (open, no conduction path). No known-good voltage is recorded for this rail.
  • Check it with the board unpowered and the battery disconnected: multimeter in diode mode, black probe on ground, red on the rail.
  • Then apply adapter power only and measure the DC voltage on the rail.
  • A diode reading far from OL (a low value or a short) usually points to a shorted part on that rail; a voltage that never appears points to the battery connector or its feed. Treat both as leads to trace, not confirmed faults.
PPVIN_G3H_P3V42G3H0.350416.22–
AI: what PPVIN_G3H_P3V42G3H is and how to check it

PPVIN_G3H_P3V42G3H is the input feed for the always-on G3H rail, per the G3H part of its name. Known-good for this board: diode 0.3504 to ground, and 16.22 V with power applied. Check it unpowered in diode mode from the net to ground, then power up with a genuine MagSafe 2 brick and measure the voltage. A diode reading well below known-good suggests a short or leaky load on the rail; a missing or low voltage points upstream toward the adapter input and isolation path. No known-good resistance reading here, so compare against a matching net or a known-good board.

PPVRTC_G3H0.43.3–
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on RTC rail (the G3H suffix, from the name, means it stays up whenever power is connected). Known-good readings here are diode 0.4 and voltage 3.3 V; the power sequence lists PPVRTC_G3H = 3.3 V in the G3 state, at C1910 pin 1.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.4.
  • With power applied, measure the voltage and expect about 3.3 V.

A far-off diode reading usually points to a short or a damaged component on the rail; a missing voltage points to the rail not being generated. No known-good resistance reading is listed for this rail.

S5 and SUS: standby 15

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.50––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC — from its name, a 1.2 V rail in the S5 (standby) domain, tied to the SMC's VDDC supply. The archive lists one known-good reading: diode mode 0.50 to ground, with no condition noted. There is no known-good voltage reading here.

  • Check it unpowered in diode mode from the rail to ground; compare with 0.50 as a guide, since community readings vary with board state.
  • Then power the board and measure the DC voltage on the rail; expect roughly 1.2 V from the name, but that figure is general, not from this board's data.
  • A diode reading far below 0.50 suggests a short or a failing part on the rail; far above suggests an open path. Confirm with a second measurement before replacing anything.
PP1V05_SUS0.291.050–
AI: what PP1V05_SUS is and how to check it

PP1V05_SUS is the 1.05 V standby rail. From its name, SUS means it belongs to the suspend/standby domain, and the board notes list it under S0 as needing PP3V3_S5 → PP3V3_SUS_FET_R to come up.

  • Known-good readings (community guide): diode 0.29 to ground, voltage 1.050 V. The notes also give PP1V05_SUS = 1.05 V in the S5 working state, after P3V3SUS_EN and PP3V3_SUS = 3.3 V.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage.
  • A voltage well below 1.05 V with PP3V3_SUS present points at the rail's own enable or switching stage rather than the load; a diode reading far from 0.29 suggests a short or a partial short on the rail.
  • No known-good resistance reading is available for this rail.
PP3V3_S50.3353.3–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail (S5/SUS stage, from its name) that comes up early in the G3-to-S3 sequence, after PP5V_S5 and before PP3V3_SUS.

  • Known-good from the readings archive: diode 0.335 to ground, voltage 3.3 V. These are community figures and a guide only; the archive gives no condition for them.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up with a genuine MagSafe 2 brick and measure the voltage.
  • A far-off diode reading usually points to a short or a damaged part on that rail; no voltage with good diode suggests the rail isn't being enabled or its source is missing.
  • No known-good resistance reading here, so compare against a matching rail or a known-good board.
PP3V3_S5_AVREF_SMC0.603.200–
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC — the name indicates a 3.3 V S5 standby reference (AVREF) for the SMC, so it belongs to the standby stage and should be up before the board leaves S5.

  • Known-good (community guide): diode 0.60 to ground, voltage 3.200 V. The notes also give a resistance check of roughly 80–100 kΩ.
  • Check with the board unpowered and the charger and battery disconnected: diode mode, red probe on ground, black on the rail. Then apply power and measure the voltage.
  • A far-low diode or resistance reading (short or partial short) suggests a fault on that net rather than the SMC itself; the notes mention this rail when PM_SLP_S4_L is missing.
  • No known-good resistance value is recorded beyond that range, and no condition is stated for the readings, so treat them as a guide and compare with a matching net or a known-good board.
PP3V3_S5_DBGLEDOL––
AI: what PP3V3_S5_DBGLED is and how to check it

PP3V3_S5_DBGLED — from its name, a 3.3 V debug-LED rail in the S5 (standby) domain. The only known-good reading in the archive is diode mode to ground: OL (open, no short to ground). No voltage reading is recorded for this rail, so there's no known-good figure here.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. OL matches the archive; a low reading (a few hundred mV or less) suggests a short or a leaky part on the rail.
  • Then check it powered: DC volts on the rail in standby. Expect roughly 3.3 V from the name, but that's general, not a recorded value.

A reading far from known-good usually points to a shorted or leaky component on that rail rather than the regulator itself. Confirm with a second measurement before replacing anything.

PP3V3_S5_REG_R0.3603.300–
AI: what PP3V3_S5_REG_R is and how to check it

PP3V3_S5_REG_R is a 3.3 V standby rail; the S5 and REG parts of the name indicate it belongs to the S5 (standby) stage.

  • Known-good readings from the archive: diode 0.360 to ground, voltage 3.300 V. These are community values and a guide only.
  • Check it with the board unpowered (MagSafe and battery disconnected) in diode mode, red probe on ground, black on the rail. Then apply power and measure the voltage.
  • A voltage far below 3.3 V points to the rail not coming up or being loaded down; a diode reading far below 0.360 suggests a partial short on the rail. No known-good resistance reading is recorded for this rail.
PP3V3_S5_SMC_VDDA0.323.400–
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply; the S5/SUS part of the name places it in the standby stage, before the board comes fully up. Known-good readings here are diode 0.32 to ground and 3.400 V with power applied; the G3-to-S3 sequence also lists it at 3.42 V and notes diode mode should not read OL with the inductor removed. Check it unpowered in diode mode to ground first, then power the board and measure the voltage. A diode reading far from 0.32, or a voltage well off 3.4 V, usually points to a short or a missing enable/upstream supply rather than the SMC alone, but that is a likely cause, not a confirmed one. No known-good resistance reading is recorded for this rail.

PP3V3_S5RS3RS0_SYSCLKGEN0.353.300–
AI: what PP3V3_S5RS3RS0_SYSCLKGEN is and how to check it

PP3V3_S5RS3RS0_SYSCLKGEN — reference note

  • What it is: a 3.3 V clock-generator supply. From the name it belongs to the S5/SUS standby stage and stays up across S5, S3 and S0, so it is present in standby and remains through later states.
  • Known-good readings (community data, a guide only): diode 0.35 to ground, voltage 3.300 V. No known-good resistance value here.
  • How to check: with the board unpowered, diode mode from the net to ground; then power up and measure the voltage at the net.
  • If it's off: a voltage well below 3.3 V with the enable present points to the rail's source or a load pulling it down; a diode reading far from 0.35 suggests a short or open on the net. Confirm with a second measurement before replacing anything.
PP3V3_SUS0.513.300–
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V suspend rail, a standby (S5/SUS) supply that comes up before the main S4/S3/S0 rails; that stage comes from the rail's name. Known-good readings here are diode 0.51 and voltage 3.300; the power sequence lists PP3V3_SUS = 3.3V in the S5 working state, with P3V3SUS_EN at 3.3V. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A far-off diode reading usually points to a short or a leaky part on the rail, while missing voltage with the enable present points upstream at the enable or the regulator; no known-good resistance reading is recorded here.

PP3V3_SUS_FET_R0.423.300–
AI: what PP3V3_SUS_FET_R is and how to check it

PP3V3_SUS_FET_R is a standby (S5/SUS) rail on the 820-00165, judged from its name; it sits between PP3V3_S5 and PP1V05_SUS in the S0 list. Known-good readings here are diode 0.42 and voltage 3.300, with no condition recorded. Check it with the board unpowered in diode mode to ground, then power up and measure the voltage. A diode reading far from 0.42 suggests a short or leaky load on that net; a missing or low voltage points back to the SUS enable and the S5 rail feeding it. No known-good resistance reading here, so compare against a matching net or a known-good board.

PP5V_S50.435–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail (S5, from the name), one of the S5 rails listed for this board.

  • Known-good readings from the archive: diode 0.43 to ground, voltage 5 V. These are community values and a guide only.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • In the G3-to-S3 sequence, PP5V_S5 should appear after P3V3S5_EN_R = 3.3 V and before PP3V3_S5 = 3.3 V.
  • A diode reading well below 0.43 suggests a short on the rail; a missing 5 V with the enable present points to the regulator feeding it. No known-good resistance reading is recorded here.
PPBUS_S5_HS_COMPUTING_ISNS0.1288.600–
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it

PPBUS_S5_HS_COMPUTING_ISNS (820-00165) — a current-sense line on the main PPBUS rail, in the S5 standby group. The "S5" and "SUS" in the name place it at the standby stage; "ISNS" indicates a sense input rather than a supply.

  • Known-good readings from the archive: diode 0.128 and voltage 8.600. No condition is recorded for either, so treat them as a guide only.
  • To check: power off and unplug, then measure diode mode from the net to ground. Power up with a genuine MagSafe 2 brick and measure the voltage.
  • A diode reading far from 0.128 suggests a short or a leaky part on the net; a voltage well off 8.6 V points at the PPBUS feed or the sense circuit itself. There is no known-good resistance reading for this net, so compare against a matching net or a known-good board before condemning anything.
PPBUS_S5_HS_OTHER_ISNS0.1378.600–
AI: what PPBUS_S5_HS_OTHER_ISNS is and how to check it

PPBUS_S5_HS_OTHER_ISNS is a standby-stage (S5/SUS) high-side current-sense rail on the main PPBUS feed; that reading of the name is from the rail's name, not from a schematic. Known-good here: diode 0.137 and 8.600 V, with no condition recorded, so treat them as a guide only. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode far below 0.137 suggests a short or leaky load on the rail; a voltage well off 8.600 V points to the PPBUS supply or its sensing path. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPVOUT_S5_PCH_DCPSUSBYP0.29––
AI: what PPVOUT_S5_PCH_DCPSUSBYP is and how to check it

PPVOUT_S5_PCH_DCPSUSBYP — the name marks it as an S5 (standby) rail feeding the PCH's DCPSUS bypass input; that reading is from the name, not a schematic.

  • Known-good: diode 0.29 to ground. No known-good voltage is recorded for this rail.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power up and measure the voltage.
  • A diode reading far below 0.29 suggests a partial short on that rail; a much higher or open reading suggests a broken feed or a missing part. One reading alone doesn't condemn a part — compare against a matching rail or a known-good board before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP_R0.26––
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it

PPVOUT_S5_PCH_DCPSUSBYP_R — reference note

  • What it is: from the name, a PCH-side output rail in the S5 (standby) domain; the "DCPSUSBYP" part suggests a bypass feed for the PCH's deep-sleep/USB-related supply. The exact circuit isn't documented here, so treat that as name-based inference only.
  • Known-good reading: diode mode to ground 0.26 (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on that rail; an open or high reading points to a missing feed. Confirm with the voltage measurement before suspecting any part.

S4 12

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.43.300–
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail that comes up at the S4 stage of the power sequence (S4 from the name), after the S5 rails and before S3. In this board's readings it shows a known-good diode value of 0.4 and a voltage of 3.300, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far below 3.3 V usually points to the rail not being enabled or loaded down, while a diode reading well under 0.4 suggests a short on the rail; a single reading isn't proof, so compare against a matching rail or a known-good board. No known-good resistance value is listed here.

PP3V3_S4_FET_R0.38––
AI: what PP3V3_S4_FET_R is and how to check it

PP3V3_S4_FET_R — the name suggests a 3.3V rail in the S4 startup stage, and the "_FET_R" suffix usually means a switched FET output or its gate-side node (that part is general naming, not from this board's data).

  • Known-good: diode 0.38 to ground, from the readings archive. No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage; compare against the S4 rail group (PP3V3_S4, PP3V3_S4SW_SNS) and the S4 stage in the power sequence.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; an open or high reading suggests a missing connection or a FET that isn't switching. Confirm with voltage under power before replacing anything.
PP3V3_S4_IPD0.38000.350 TP+and+KB+Installed3.300–
AI: what PP3V3_S4_IPD is and how to check it

PP3V3_S4_IPD is a 3.3 V rail that comes up at the S4 stage of the power sequence, judging from its name (the S4 suffix); the "IPD" part isn't explained in the available data. Known-good readings are diode 0.3800 to ground, diode 0.350 with TP and KB installed, and 3.300 V with power applied — community values, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far below 3.3 V at S4 points to the rail not being enabled or being loaded down, while a diode reading much lower than 0.35–0.38 suggests a short on the rail; no known-good resistance reading is recorded here.

PP3V3_S4_TBT_F0.38––
AI: what PP3V3_S4_TBT_F is and how to check it

PP3V3_S4_TBT_F is a 3.3 V rail that comes up in the S4 stage, judging from its name (S4 = S4 state; TBT usually means Thunderbolt). The only known-good figure recorded here is a diode reading of 0.38 to ground; there is no known-good voltage or resistance value for this rail in the data.

  • Diode check: power off, unplug the MagSafe and battery, then measure diode mode from the rail to ground. Around 0.38 is the guide; a much lower reading suggests a short on the rail.
  • Voltage check: with power applied and the board in S4, expect roughly 3.3 V, since S4 rails in this sequence are 3.3 V (general expectation, not a recorded value for this net).
  • A far-off diode reading usually points to a shorted load on the rail rather than the regulator itself; confirm with a second measurement before replacing anything.
PP3V3_S4_TBTAPWR0.453.300–
AI: what PP3V3_S4_TBTAPWR is and how to check it

PP3V3_S4_TBTAPWR — a 3.3 V rail enabled at the S4 stage, from the name; the "TBTA" part suggests it feeds Thunderbolt-related power, though that's inference from the name, not from board data.

  • Known-good readings here: diode 0.45 to ground, voltage 3.300. No known-good resistance reading is listed for this net.
  • Check with the board unpowered and the battery/adapter removed: diode mode, red probe on ground, black on the rail. Then apply power and confirm it comes up at 3.3 V once the board reaches S4.
  • A diode reading far below 0.45 suggests a short or leaky load on the rail; a missing 3.3 V with a normal diode reading points upstream, to the S4 enable and the rails feeding it (PP3V3_S5, PP3V3_SUS, PM_SLP_S4_L).
  • Readings are community guides and vary with board state, so treat a small difference as normal and confirm before replacing anything.
PP3V3_S4SW_SNS0.503.300–
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail that comes up in the S4 stage of the power sequence (from its name). The archived readings are diode 0.50 and 3.300 V; treat these as a guide, since community readings vary with board state.

  • With the board unpowered, measure diode mode from the rail to ground; around 0.50 is the known-good figure here.
  • Then power the board and check for 3.300 V.
  • A diode reading far below 0.50 suggests a short or a leaky load on the rail; a missing voltage with a good diode reading points upstream, to the S4 enable and the rails feeding it.

No known-good resistance reading is recorded for this rail.

PP3V3_S4SW_SNS_FET_R0.49––
AI: what PP3V3_S4SW_SNS_FET_R is and how to check it

PP3V3_S4SW_SNS_FET_R — reference note

  • This is a sense line tied to the switched 3.3 V S4 rail; the "S4" in the name places it in the S4 startup stage, and "SW"/"SNS"/"FET_R" suggest a switched-rail sense point at a FET, from the name alone.
  • Known-good here is a diode reading of 0.49 to ground. No known-good voltage or resistance value is recorded for this net.
  • Check it with the board unpowered in diode mode, red probe on ground, black on the net, and compare with 0.49. Then power up and confirm the S4 rail comes up at 3.3 V (PP3V3_S4 is listed at 3.3 V in the S4 state).
  • A diode reading far below 0.49 suggests a short or leaky part on that line; a much higher or open reading suggests a broken connection. One reading alone doesn't condemn a part, so re-check and compare against a matching net before replacing anything.
PP3V3RHV_S4_TBTAPWR0.553.300–
AI: what PP3V3RHV_S4_TBTAPWR is and how to check it

PP3V3RHV_S4_TBTAPWR — a 3.3 V rail enabled at the S4 stage, from the name. The "RHV" and "TBTA" parts suggest a high-voltage-tolerant supply for the Thunderbolt area, but that's general reading of the name, not from this board's data.

  • Known-good readings here: diode 0.55, voltage 3.300. These are community figures and a guide only.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A voltage far below 3.3 V with S4 reached points to the rail not being enabled or its source failing; a diode reading well under 0.55 suggests a short on the rail. Confirm with a second measurement before replacing anything.
PP3V3RHV_S4_TBTAPWR_F0.57––
AI: what PP3V3RHV_S4_TBTAPWR_F is and how to check it

PP3V3RHV_S4_TBTAPWR_F — from the name, a 3.3V rail in the S4 startup stage, feeding Thunderbolt adapter power. The "RHV" part isn't explained in the available data.

  • Known-good: diode 0.57 (no condition recorded). No known-good voltage reading here.
  • Check it with the board unpowered and the adapter/battery removed: multimeter in diode mode, black probe on ground, red on the rail.
  • Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.57 suggests a partial short on that rail; far above suggests an open path. Confirm with a second measurement before replacing anything.
PP5V_S4_IPD0.43460.430 TP+and+KB+Installed5.000–
AI: what PP5V_S4_IPD is and how to check it

PP5V_S4_IPD — the name marks it as a 5 V rail that comes up at the S4 stage of the power sequence (from the name; "IPD" isn't expanded anywhere in the available data).

  • Known-good readings: diode 0.4346 to ground, and 0.430 in the "TP+and+KB+Installed" condition; voltage 5.000 V.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the voltage.
  • A diode reading well below the known-good values suggests a partial short or a leaky part on the rail; a missing 5 V with power applied points upstream, to the S4 enable and the rail's supply circuit rather than the rail itself.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board.
PP5V_S4RS30.4045.000–
AI: what PP5V_S4RS3 is and how to check it

PP5V_S4RS3 is the 5 V rail that comes up at the S4 stage of the power sequence (S4 stage taken from the rail's name). Known-good readings here: diode 0.404 to ground and 5.000 V with the board powered. No known-good resistance reading is recorded for this rail.

  • Check it unpowered in diode mode, probe to ground: around 0.404 is the guide value.
  • Then power the board and measure the voltage: about 5.000 V means the rail is up.
  • A diode reading far below 0.404 suggests a short or a leaky load on the rail; a missing 5 V with a normal diode reading points upstream, at the S4 enable and the regulator feeding it, not at the rail itself.

These are community readings and vary with board state, so treat them as a guide rather than a confirmed fault.

PPVIN_S4SW_TBTBST_FET0.50––
AI: what PPVIN_S4SW_TBTBST_FET is and how to check it

PPVIN_S4SW_TBTBST_FET — from the name, this is a switched input rail in the S4 startup stage, feeding a Thunderbolt boost (TBTBST) FET. The known-good reading here is diode mode to ground: 0.50. No voltage reading is recorded for this rail.

  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Compare with 0.50.
  • Then power the board and measure the voltage on the rail; no known-good voltage here, so compare against a matching net or a known-good board.
  • A diode reading far below 0.50 suggests a short or a leaky part on the rail; far above suggests an open path. One reading alone doesn't confirm a bad part.

S3: memory 19

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.46––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it

PP0V6_S3_MEM_VREFCA_A — from its name, a 0.6 V memory reference voltage that comes up in the S3 (suspend-to-RAM) stage. The only known-good figure recorded here is a diode reading of 0.46 to ground; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.46. A much lower reading suggests a short or leaky part on the rail; a much higher one can mean an open path or a missing component.
  • Then power the board and measure the voltage, ideally after it has reached S3. No known-good voltage is recorded here, so compare against a known-good board or the reference the rail's name implies (about 0.6 V).
  • A large departure from 0.46 in diode mode is the more useful early clue; one reading alone doesn't confirm a bad part.
PP0V6_S3_MEM_VREFCA_B0.45––
AI: what PP0V6_S3_MEM_VREFCA_B is and how to check it

PP0V6_S3_MEM_VREFCA_B — the name suggests a 0.6 V memory reference (VREF) for the CA bus, active in the S3 state; that reading is from the name, not from a schematic.

  • Known-good: diode-to-ground 0.45 (community reading, a guide only). No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the net.
  • Then power up and measure the DC voltage on the net; compare with a matching VREF net on the other memory channel if one exists.
  • A diode reading far from 0.45 usually points to a short or a leaky part on that reference, but one reading isn't proof — recheck before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.44––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail that comes up in the S3 stage — that reading is from the rail's name, not from a schematic. The only known-good figure in the archive is a diode reading of 0.44 to ground; there is no known-good voltage or resistance value recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage, comparing against the 0.44 guide. A diode reading far below 0.44 suggests a short or leaky load on the rail, while a far higher or open reading points to a broken connection or missing component; a single reading isn't proof, so confirm with a second measurement before replacing anything.

PP0V6_S3_MEM_VREFDQ_B0.43––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B — reference note

  • This is a 0.6 V memory reference rail that comes up in the S3 state; the "0V6" and "S3" parts come from the rail name, and "VREFDQ" is the DDR data-reference voltage (general naming, not board data).
  • Known-good: diode reading to ground 0.43. No known-good voltage reading is recorded here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up into S3 and measure the DC voltage.
  • A diode reading far from 0.43 usually points to a short or a leaky part on that net; a voltage well off 0.6 V points to the reference divider or its source. Neither alone confirms a bad part — compare with a matching net or a known-good board before replacing anything.
PP1V2_S30.1301.2–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail that, from its name, belongs to the S3 (memory) startup stage. The archive lists a known-good diode reading of 0.130 and a voltage of 1.2; no condition is recorded for either, so treat them as a guide.

  • With the board unpowered, measure diode mode from PP1V2_S3 to ground and compare with 0.130.
  • With power applied, measure the voltage and expect about 1.2 V once the board has reached S3.

A reading far from known-good usually points to a short or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part. There is no known-good resistance value for this rail here.

PP1V2_S3_SD_DVDD120.26––
AI: what PP1V2_S3_SD_DVDD12 is and how to check it

PP1V2_S3_SD_DVDD12 — reference note

  • What it is: the "S3" in the name places it in the memory/S3 startup stage; "1V2" indicates a 1.2 V rail, and "SD_DVDD12" suggests it feeds SD card DVDD. The rest of the name is from the rail's naming, not from a schematic here.
  • Known-good reading: diode 0.26 to ground, from the community archive. No known-good voltage or resistance value is recorded for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.26. Then power up and measure the voltage at the rail; it should come up when the board reaches S3.
  • If it's far off: a diode reading well below 0.26 suggests a partial short on the rail; no voltage at S3 points to the rail's enable or supply upstream. Treat 0.26 as a guide only, since readings vary with board state, and confirm before replacing anything.
PP1V8_S30.31.8–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail in the S3 (memory) startup stage, as the name indicates. Known-good readings here are diode 0.3 to ground and 1.8 V with power applied; no condition is recorded for either.

  • With the board unpowered, measure diode mode from PP1V8_S3 to ground and expect about 0.3.
  • Then power up and measure the voltage on the rail; expect 1.8 V.
  • A far lower diode reading suggests a short or a failing load on the rail; a missing or low voltage with a normal diode reading points upstream, at the rail's enable or its source regulator.

These readings are community guides and vary with board state, so treat a small difference as normal rather than condemning a part.

PP1V8_S3_REG_R0.371.800–
AI: what PP1V8_S3_REG_R is and how to check it

PP1V8_S3_REG_R is a 1.8 V regulated rail in the S3 (memory) startup stage, judged from its name. Known-good readings here: diode 0.37 and voltage 1.800. With the board unpowered, measure diode mode from the rail to ground; then power up and confirm about 1.8 V. A diode reading far from 0.37 suggests a short or leaky part on that rail; no known-good resistance reading is available for it.

PP3V3_S30.473.300–
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that comes up at the S3 stage, which from its name is the memory stage of the power sequence. Known-good readings here are diode 0.47 and voltage 3.300.

  • With the board unpowered, measure diode mode from PP3V3_S3 to ground; 0.47 is the guide value.
  • Then apply power and confirm about 3.300 V once the board has reached S3.
  • A diode reading far below 0.47 suggests a short or a partly shorted load on the rail; a voltage well under 3.300 V with the enable present points to the rail's regulator or its load.

No known-good resistance reading is recorded for this rail. These are community figures and vary with board state, so treat them as a guide rather than a confirmed fault until compared with a matching net or a known-good board.

PP3V3_S3_FET_R0.47––
AI: what PP3V3_S3_FET_R is and how to check it

PP3V3_S3_FET_R — an S3-stage rail (memory stage, from the name). It is the FET-side node of the 3.3V S3 supply, so it should come up when the board reaches S3.

  • Known-good: diode to ground 0.47 (community reading, guide only). No known-good voltage reading here.
  • Check: power off and unplugged, diode mode from the rail to ground; then power up and measure the voltage at S3.
  • A diode far below 0.47 suggests a short on that node; far above suggests an open path. Confirm with a second reading before replacing anything.
PP3V3_S3_VREFMRGN_DAC0.473.300–
AI: what PP3V3_S3_VREFMRGN_DAC is and how to check it

PP3V3_S3_VREFMRGN_DAC is a 3.3 V S3 rail; the "S3" stage is the memory state, taken from the name, and "VREFMRGN_DAC" suggests a reference/margin DAC supply (general reading, not from this board's data). Known-good here: diode 0.47 to ground and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.47 or a voltage well off 3.300 V usually points to a short or a missing enable on that rail, but one reading alone doesn't confirm a bad part. No known-good resistance reading is recorded for this rail.

PP3V3_S3RS0_CAMERA0.26––
AI: what PP3V3_S3RS0_CAMERA is and how to check it

PP3V3_S3RS0_CAMERA — a 3.3 V rail for the camera circuit. The S3 in the name places it in the memory/S3 startup stage, and the name suggests it is derived from the S3 rail and switched (RS0) to the camera. That reading is from the name only.

  • Known-good diode reading to ground: 0.26 (community value, a guide only; it varies with board state).
  • No known-good voltage reading here, so compare against a matching 3.3 V rail or a known-good board.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.26 usually points to a short or a leaky part on that rail; a missing voltage with a normal diode reading points more to the enable or the source rail feeding it. Neither is confirmed until you measure.
PP3V3_S3RS0_CAMERA_R0.37––
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it

PP3V3_S3RS0_CAMERA_R — the name indicates a 3.3 V rail in the S3 (memory/suspend-to-RAM) startup stage, with "RS0" and "CAMERA" suggesting a switched branch feeding the camera. That reading is from the name, not from board data.

  • Known-good: diode 0.37 (community reading, no condition given). No known-good voltage or resistance is recorded here.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail, and compare with 0.37.
  • Then power up and measure the voltage; expect about 3.3 V once the board reaches S3.
  • A diode reading far below 0.37 points to a short or leaky part on that branch; a much higher or open reading points to a broken feed. One reading alone doesn't confirm a bad part.
PP5V_S3_RTUSB_A_F0.4545.100–
AI: what PP5V_S3_RTUSB_A_F is and how to check it

PP5V_S3_RTUSB_A_F is a 5 V rail that comes up at the S3 stage (memory state, from the name) and feeds the right-side USB-A port. Known-good readings from the archive: diode 0.454 and voltage 5.100, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.454 suggests a short or leaky part on that rail; no known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP5V_S3_RTUSB_A_ILIM0.4545.100–
AI: what PP5V_S3_RTUSB_A_ILIM is and how to check it

PP5V_S3_RTUSB_A_ILIM — from its name, a 5 V rail in the S3 (memory) startup stage, with an "ILIM" tag suggesting it feeds a current-limit reference for USB-A power switching. That's general naming convention, not confirmed by this board's data.

  • Known-good: diode 0.454, voltage 5.100 V (community reading, a guide only; no condition recorded).
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up with a genuine MagSafe 2 brick and measure the voltage.
  • A diode reading far below 0.454 suggests a short or leaky load on the rail; a missing 5.1 V with a normal diode reading points upstream, to the S3 enable and the 5 V source feeding it. No known-good resistance reading is recorded here.
PP5V_S3_U62100.44––
AI: what PP5V_S3_U6210 is and how to check it

PP5V_S3_U6210 is a 5 V rail that comes up at the S3 stage, which from its name is the memory stage of the power sequence. Its only known-good reading here is a diode value of 0.44; there is no known-good voltage or resistance value for it in this data.

  • With the board unpowered, measure diode mode from the rail to ground; around 0.44 is the guide, and a much lower reading suggests a short on that rail.
  • Then power the board and check the voltage, comparing against the S3 rails listed for this board (PP3V3_S3, PP1V8_S3, PP1V2_S3) and the S3 stage of the sequence.
  • A reading far from 0.44 or a missing 5 V usually points to the rail not being enabled or a fault on the rail itself, but a single reading doesn't confirm a bad part.

The U6210 in the name is likely the rail's switching IC, but that is general naming convention, not confirmed by this data.

PP5V_S3RS0_ALSCAM_F0.4486––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it

PP5V_S3RS0_ALSCAM_F — the name indicates a 5 V rail that comes up at the S3 stage (memory state, from the name) and feeds the ALS/camera circuit; "F" suggests a fused branch. The only known-good reading recorded is a diode value of 0.4486 to ground; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.4486. A much lower reading suggests a short or leaky load on that branch; a much higher or OL reading suggests an open trace or fuse.
  • Then power the board and measure the voltage; it should be about 5 V once the board reaches S3. No voltage means the S3 enable or upstream 5 V source isn't coming up; correct voltage with a wrong diode reading points at the load side.
  • These are community readings and vary with board state, so treat them as a guide, not a pass/fail limit.
PPDDR_S3_REG_R0.130––
AI: what PPDDR_S3_REG_R is and how to check it

PPDDR_S3_REG_R is a memory-rail net on this board; the "S3" in its name marks it as part of the S3 (memory) startup stage, and "DDR" points to the memory supply. The only known-good figure in the archive is a diode reading of 0.130 to ground; there is no known-good voltage here. Check it with the board unpowered in diode mode, red probe on ground and black on the net, then power up and measure the voltage on it. A diode reading far from 0.130 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVTT_S3_DDR_BUF0.48––
AI: what PPVTT_S3_DDR_BUF is and how to check it

PPVTT_S3_DDR_BUF — from the name, a DDR memory buffer termination rail that comes up in the S3 (memory) startup stage.

  • Known-good: diode 0.48 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, black probe on ground, red on the rail; then power the board and measure the voltage.
  • A diode reading far below 0.48 suggests a short or leaky part on that rail; a reading well above it can mean an open path. One reading alone doesn't condemn a part — confirm with a voltage check and compare against a known-good board.

S0: running 45

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.1080.6–
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT is the 0.6 V DDR termination rail, active in S0 (running), as the name indicates. Known-good readings here are diode 0.108 to ground and 0.6 V with the board powered in S0; no resistance value is listed. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage in S0. A diode reading far from 0.108 suggests a short or leaky part on the rail; a voltage well off 0.6 V with the board running points to the rail's regulator or its enable. These are community readings and vary with board state, so treat them as a guide.

PP1V2_S0_SD_AVDD120.26––
AI: what PP1V2_S0_SD_AVDD12 is and how to check it

PP1V2_S0_SD_AVDD12 — reference note

  • From its name, this is a 1.2 V rail that comes up in the S0 (running) state and feeds an SD-related AVDD supply. The name is the only description available; which parts sit on the net isn't documented.
  • Known-good reading: diode mode to ground 0.26 (community value, a guide only, no condition recorded). No known-good voltage or resistance reading is recorded for this rail.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the DC voltage at the rail.
  • A diode reading far from 0.26 usually points to a short or a leaky load on the rail rather than the regulator itself; confirm with a second reading before replacing anything.
PP1V2_S0_SD_VUHS10.42––
AI: what PP1V2_S0_SD_VUHS1 is and how to check it

PP1V2_S0_SD_VUHS1 — reference note

  • What it is: a 1.2 V rail, from the name, that comes up in the S0 (running) state and feeds the SD card interface's VUHS1 supply. It is not listed in this board's power-rail sequence notes, so its exact source and load aren't documented here.
  • Known-good reading: diode to ground 0.42 (community value, a guide only; no condition recorded). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; power up and measure the voltage in S0.
  • If it's far off: a low or shorted diode reading points to a shorted load on the rail; a correct diode reading with no voltage points upstream, to the rail's enable or source. Confirm with a second measurement before replacing anything.
PP1V05_S00.1121.050–
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V S0 (running-state) rail; the S0 part comes from its name. Known-good readings here are diode 0.112 and voltage 1.050, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare with 0.112; then power up and check for about 1.05 V. A diode reading far below known-good suggests a short or leaky load on the rail, while correct diode but missing voltage points back at the rail's enable or source. These community readings are a guide only, and no known-good resistance value is listed for this rail.

PP1V5_S00.41.5–
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail in the S0 (running) state, judging from its name; the S0 rails come up late in the sequence, after the S5, S4 and S3 rails. Known-good readings here are diode 0.4 and voltage 1.5, with no condition noted, so treat them as a guide. With the board unpowered, measure diode mode from PP1V5_S0 to ground and compare with 0.4; then power up and check for about 1.5 V. A far-off diode reading usually points to a short or a damaged component on that rail, while correct diode but missing voltage points upstream to its enable or source. No known-good resistance reading is recorded for this rail.

PP1V05_S0_PCH_VCC_ICC0.15––
AI: what PP1V05_S0_PCH_VCC_ICC is and how to check it

PP1V05_S0_PCH_VCC_ICC — the name says it's a 1.05 V rail for the PCH (chipset) VCC, and the S0 prefix puts it in the running stage. The only known-good figure in the archive is a diode reading of 0.15 to ground; no known-good voltage is recorded here. Check it unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage at the rail. A diode reading far from 0.15 suggests a short or a leaky load on that rail, but confirm with a second measurement before suspecting a part.

PP1V05_S0_PCH_VCC_ICC_R0.15––
AI: what PP1V05_S0_PCH_VCC_ICC_R is and how to check it

PP1V05_S0_PCH_VCC_ICC_R — the name indicates a 1.05 V S0 (running-state) rail feeding the PCH VCC_ICC supply. The "R" suffix suggests a remote-sense or resistor-linked variant; that part is inference from the naming, not confirmed by board data.

  • Known-good: diode-to-ground 0.15 (community reading, guide only). No known-good voltage reading here.
  • Check: board unpowered, diode mode, black probe on ground, red on the rail; then power up and measure DC volts at the rail.
  • A diode reading far below 0.15 suggests a short on the rail; far above suggests an open. Confirm with a second point on the same net before suspecting a part.
PP1V05_S0_PCH_VCCACLKPLL0.151.040–
AI: what PP1V05_S0_PCH_VCCACLKPLL is and how to check it

PP1V05_S0_PCH_VCCACLKPLL — reference note

  • This is a 1.05 V S0 rail feeding the PCH's ACLK PLL supply. The "S0" in the name means it belongs to the running state; the rest of the name points to the PCH clock/PLL domain (from the name, not from a schematic).
  • Known-good readings in the archive: diode 0.15 to ground, and 1.040 V with the board powered and running. These are community values and only a guide.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage at the rail.
  • A diode reading well above 0.15 suggests an open or missing connection rather than a short; a reading near 0 suggests a short on the rail. A voltage far from 1.040 V with the board in S0 points at the rail's regulator or its enable, not the PCH itself.
  • No known-good resistance reading is recorded for this rail.
PP1V05_S0_PCH_VCCACLKPLL_R0.15––
AI: what PP1V05_S0_PCH_VCCACLKPLL_R is and how to check it

PP1V05_S0_PCH_VCCACLKPLL_R — from the name, a 1.05 V S0 (running) rail feeding the PCH's ACLK PLL supply. The only known-good figure here is a diode reading of 0.15 to ground.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Compare against 0.15 as a guide; a short or near-zero suggests a shorted load on that rail.
  • Then power up and measure the voltage; no known-good voltage is recorded here, so expect roughly 1.05 V from the name and compare with a known-good board.
  • A reading far from known-good usually points to a shorted component on the rail or a missing enable/upstream supply, not confirmed until traced.
PP1V05_S0_PCH_VCCAPLL_OPI0.141.000–
AI: what PP1V05_S0_PCH_VCCAPLL_OPI is and how to check it

PP1V05_S0_PCH_VCCAPLL_OPI — the name says it's a 1.05 V S0 (running-state) rail feeding the PCH's VCCAPLL / OPI supply. It comes up only after the board is in S0, so it should not be expected before the S0 rails.

  • Known-good readings in the archive: diode 0.14 to ground, voltage 1.000 V with the board powered and running. No condition is recorded, so treat these as a guide.
  • To check: power off and unplug, then diode mode from the rail to ground — a far lower reading than 0.14 suggests a short on the rail; a much higher one suggests an open feed.
  • Then power up into S0 and measure the voltage; near 1.0 V is normal, and 0 V means the rail isn't being enabled or its source is missing, so trace back through the S0 enable sequence.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board.
PP1V05_S0_REG_R0.112–160.000R
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V S0 (running-state) regulated rail; the S0 stage comes from the name. Known-good readings here: diode 0.112 and resistance 160.000R, with no condition noted, so treat them as a guide only. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from these usually points to a short or a faulty regulator on that rail, but no known-good voltage is recorded here, so confirm the expected level from the rail's name and a known-good board before condemning anything.

PP1V5_S0SW_AUDIO0.351.500–
AI: what PP1V5_S0SW_AUDIO is and how to check it

PP1V5_S0SW_AUDIO — reference note

  • This is a 1.5 V switched audio rail. From the name: "S0" means it comes up in the running (S0) state, "SW" means it is switched on by an enable, and "AUDIO" marks it as an audio-domain supply. General knowledge, not from this board's data: such rails usually feed the audio codec and its analog stages.
  • Known-good readings for this board: diode 0.35 to ground, and 1.500 V with the board powered and in S0. These are community readings and only a guide; the state of the board affects them.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up, let the board reach S0, and measure the voltage.
  • A diode reading well below 0.35 suggests a short or a leaky load on the rail; a voltage far from 1.500 V with the enable present points to the rail's switch or its source supply. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.
PP1V5_S0SW_AUDIO_HDA0.341.500–
AI: what PP1V5_S0SW_AUDIO_HDA is and how to check it

PP1V5_S0SW_AUDIO_HDA — reference note

  • This is the 1.5 V audio/HDA rail, switched on in the S0 (running) state — the "S0SW" and "AUDIO_HDA" parts come from the rail's name.
  • Known-good from the readings archive: diode 0.34 to ground, and 1.500 V with the board powered and running. Treat these as a guide, since community readings vary with board state.
  • To check it: power off and unplug, then measure diode mode from the rail to ground; power up and confirm about 1.500 V in S0.
  • A diode reading far from 0.34 usually points to a short or leaky part on the rail; a correct diode reading with missing voltage points more to the enable or supply feeding it. No known-good resistance value is listed here.
PP1V05_S0SW_PCH_HSIO0.221.0500.000R
AI: what PP1V05_S0SW_PCH_HSIO is and how to check it

PP1V05_S0SW_PCH_HSIO is a 1.05 V S0 (running) rail feeding the PCH high-speed I/O, as the name suggests; it's listed under the S0 rails for this board. Known-good readings here are diode 0.22 and 1.050 V, with a resistance of 0.000R noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A reading far from 0.22 in diode mode or well off 1.05 V usually points to a short or a rail not being enabled, but one reading alone doesn't confirm a bad part.

PP1V05_S0SW_PCH_VCCSATA3PLL0.22–330.000R
AI: what PP1V05_S0SW_PCH_VCCSATA3PLL is and how to check it

PP1V05_S0SW_PCH_VCCSATA3PLL — reference note

  • This is a 1.05 V S0 rail feeding the PCH's SATA 3 PLL supply, judging from the name; the "S0" part means it should only come up once the board is in the running (S0) state, after the S3 and S4 rails.
  • Known-good readings from the archive: diode 0.22 to ground, resistance 330.000R. These are community figures and a guide only, not a spec.
  • To check it, power off and unplug the adapter and battery, then measure diode mode from the rail to ground; then apply power and measure the voltage, which should sit near 1.05 V once the board has reached S0.
  • No known-good voltage reading is recorded here, so compare against the 1.05 V the name implies and against a matching rail on a known-good board.
  • A diode reading far below 0.22 usually points to a shorted load or decoupling cap on the rail; a correct diode reading with no voltage points instead to the rail's enable or its source regulator, so trace the enable signal before replacing anything.
PP1V05_S0SW_PCH_VCCUSB3PLL0.231.037–
AI: what PP1V05_S0SW_PCH_VCCUSB3PLL is and how to check it

PP1V05_S0SW_PCH_VCCUSB3PLL — from the name, a 1.05 V S0 (running) switched rail feeding the PCH's USB 3.0 PLL supply. The name says it's only expected up once the board is in S0.

  • Known-good from the archive: diode 0.23 to ground, voltage 1.037 V. These are community readings and a guide only; the data gives no condition for them.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up in S0 and measure the voltage.
  • A diode reading well below 0.23 suggests a partial short on that rail; a missing or low voltage with a normal diode reading points upstream, to its enable or the S0 power sequence.
  • No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.
PP3V3_S00.3903.300–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that comes up at the S0 (running) stage, judging from its name. In the readings archive its known-good values are diode 0.390 and voltage 3.300; treat these as a guide, since community readings vary with board state. With the board unpowered, measure diode mode from PP3V3_S0 to ground and compare with 0.390. Then power up and confirm about 3.300 V; a far-off diode reading usually points to a short or a faulty part on that rail, while missing voltage at S0 points back to the enable and earlier rails. No known-good resistance reading is recorded here.

PP3V3_S0_CPUTHMSNS_R0.433.200–
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R is a 3.3 V S0 rail; the name suggests it carries the CPU thermal-sense (temperature) signal, and S0 means it belongs to the running state. That reading is from the name, not from a schematic.

  • Known-good here: diode 0.43 to ground, and 3.200 V with the board powered in S0. Treat these as a community guide, not a guaranteed value.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and confirm 3.200 V once the board reaches S0.
  • A diode reading well below 0.43 suggests a partial short or a leaky part on the rail; a missing 3.200 V with a normal diode reading points upstream, at whatever enables this rail or its source.
  • No known-good resistance reading is listed for this rail.
PP3V3_S0_FAN0.37––
AI: what PP3V3_S0_FAN is and how to check it

PP3V3_S0_FAN (820-00165) — the name indicates a 3.3 V rail that comes up in the S0 (running) state and feeds the fan circuit; that meaning is from the name, not from a schematic.

  • Known-good: diode 0.37 to ground (community reading, a guide only). No known-good voltage reading here.
  • Check unpowered: diode mode, red probe on ground, black on the rail; compare with 0.37.
  • Check powered: DC volts on the rail in S0; no known-good voltage is listed, so compare with a known-good board or the same rail on a matching net.
  • A diode reading far below 0.37 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PP3V3_S0_FET_R0.37––
AI: what PP3V3_S0_FET_R is and how to check it
  • What it is: From the name, a 3.3 V rail in the S0 (running) state, gated by a FET. It's listed in the S0 group of rails.
  • Known-good reading: diode 0.37 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from PP3V3_S0_FET_R to ground. Then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a high or open reading suggests a missing connection. A wrong voltage with a normal diode reading points more to the FET's gate/enable side. These are guides, not confirmed faults.
PP3V3_S0_SD_AVDD330.41––
AI: what PP3V3_S0_SD_AVDD33 is and how to check it

PP3V3_S0_SD_AVDD33 — a 3.3 V S0 (running-state) rail; the "SD_AVDD33" part of the name suggests an SD card / AVDD 3.3 V supply, though that's from the name only.

  • Known-good from the archive: diode 0.41 to ground. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.41 (much lower or near 0) usually points to a short or a leaky part on the rail; a much higher reading can mean an open path. Confirm with a voltage check before replacing anything.
PP3V3_S0_SD_CONN0.41––
AI: what PP3V3_S0_SD_CONN is and how to check it

PP3V3_S0_SD_CONN — from its name, a 3.3 V rail in the S0 (running) state, feeding the SD card connector area.

  • Known-good: diode-to-ground 0.41 (community reading, a guide only; it varies with board state). No known-good voltage reading here.
  • Check: power off and unplugged, diode mode from the rail to ground; then power on and measure the voltage, which should sit near 3.3 V.
  • A diode reading far from 0.41 suggests a short or leaky part on that rail; no voltage means the rail isn't being enabled.
PP3V3_S0_TBTMLB_ISNS_R0.43––
AI: what PP3V3_S0_TBTMLB_ISNS_R is and how to check it
  • What it is: From the name, a 3.3V S0 (running-state) rail — the "ISNS" part suggests a current-sense point, likely for the Thunderbolt section. That's general reading of the name, not confirmed by board data.
  • Known-good: diode to ground 0.43 (no condition given). No known-good voltage or resistance reading here.
  • How to check: power off, diode mode from the net to ground; then power on and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on that net; a much higher one suggests an open. One reading alone isn't proof — compare against a matching net or a known-good board before replacing anything.
PP3V3_S0SW_LCD0.5473.300–
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD — a switched 3.3 V LCD rail that comes up in the S0 (running) state, judging from the name; the "SW" suggests it is switched on by a control signal rather than always present.

  • Known-good readings from the archive: diode 0.547 to ground, voltage 3.300. No condition is recorded for these, so treat them as a guide.
  • Check it with the board unpowered and discharged: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.547 suggests a short or a leaky part on the rail; a voltage well under 3.300 with the board in S0 points to the switch or its enable not coming up, not necessarily the rail itself.
  • No known-good resistance reading is recorded for this rail.
PP3V3_S0SW_LCD_R0.5473.300–
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is a switched 3.3 V LCD rail; the "S0" in the name places it in the running state, and "SW" suggests it is switched on rather than always present (from the name). The archive lists a known-good diode reading of 0.547 and a voltage of 3.300, with no condition recorded, so treat these as a guide only.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.547.
  • With power applied and the board in S0, measure the rail voltage and expect about 3.300 V.
  • A far lower diode reading usually points to a short or a failing part on the rail; a missing voltage with a normal diode reading points upstream to its enable or switch. No known-good resistance reading is recorded here.
PP3V3_S0SW_LCD_UF0.5473.3–
AI: what PP3V3_S0SW_LCD_UF is and how to check it

PP3V3_S0SW_LCD_UF — the name indicates a 3.3 V switched LCD rail, active in the S0 (running) state; the "UF" suffix isn't explained in the available data.

  • Known-good readings: diode 0.547, voltage 3.3 V. These are community-contributed guides and can vary with board state.
  • Check with the board unpowered: diode mode, red probe to ground, black probe on the rail. Then power up and measure the voltage.
  • A voltage far off 3.3 V with the board in S0 points to the rail's enable or switch not coming up, or a load pulling it down — not proof of a bad part on its own.
  • No known-good resistance reading is available for this rail.
PP3V3_S0SW_SD0.40––
AI: what PP3V3_S0SW_SD is and how to check it

PP3V3_S0SW_SD — from the name, a 3.3 V switched S0 (running-state) rail, likely feeding the SD card circuit. It's listed in the archive with a diode reading of 0.40 to ground; there is no known-good voltage or resistance value recorded here.

  • Check it unpowered: diode mode from the rail to ground, board off and adapter/battery removed. Compare against the 0.40 guide; a much lower reading suggests a short on the rail, a much higher or open reading suggests a broken feed or enable.
  • Check it powered: measure the voltage with the board in S0. No known-good voltage is recorded, so compare with a matching rail or a known-good board.
  • A far-off diode reading usually points to a shorted load or a failed switch on that rail, but one reading alone doesn't confirm a bad part.
PP3V3_S0SW_SSD0.513.300–
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD — reference note

  • What it is: a 3.3 V rail that is switched on in the S0 (running) state, from the rail name. The "SSD" part of the name suggests it feeds the SSD side of the board (general interpretation, not from the board data).
  • Known-good readings (community archive, guide only): diode 0.51 to ground, voltage 3.300 V. No condition is recorded with these values.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading points to a short or a leaky load on the rail; 0 V or a missing 3.3 V with power applied points to the rail not being enabled or its switch not passing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning anything.
PP3V3_S0SW_SSD_FET_R0.513.300–
AI: what PP3V3_S0SW_SSD_FET_R is and how to check it

PP3V3_S0SW_SSD_FET_R — the name marks it as a 3.3 V rail switched through a FET (the FET_R suffix), in the S0 running state; that reading is from the name, not a schematic.

  • Known-good: diode 0.51 to ground, voltage 3.300. These are community readings and a guide only; no known-good resistance value here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.51.
  • Then power up and measure the voltage; it should sit at 3.3 V once the board is in S0.
  • A diode reading far below 0.51 suggests a partial short on the rail; no voltage at S0 points upstream to the FET's enable or its source rail. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_SSD_FLT0.503.300–
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a 3.3 V rail that, from its name, is a switched S0 (running) supply for the SSD. The "FLT" suffix suggests a filtered or fault-sense variant; the name alone doesn't confirm which.

  • Known-good readings here: diode 0.50 to ground, voltage 3.300 V in the S0 state. These come from community contributions, so treat them as a guide.
  • To check: power off and unplug, then diode-mode from the rail to ground. Then apply power and confirm 3.300 V once the board reaches S0.
  • A diode reading far below 0.50 suggests a short or a leaky part on the rail; a voltage well under 3.300 V in S0 points to the rail not being enabled or being loaded down.
  • No known-good resistance reading is recorded for this rail.
PP5V_S00.4305–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that comes up at the S0 (running) stage, judging by its name. In the readings archive it shows a diode value of 0.430 and 5 V; treat these as a guide only, since community readings vary with board state.

  • Check it unpowered: diode mode, black probe to ground, red to the rail. Around 0.430 is the known-good figure here.
  • Then power the board and measure the voltage; about 5 V is expected once the board reaches S0.

A diode reading far below 0.430 suggests a short or a leaky part on the rail; a much higher or open reading points to a broken connection or missing part. No known-good resistance value is listed for this rail.

PP5V_S0_ALT_AUD_LDO_ENOL––
AI: what PP5V_S0_ALT_AUD_LDO_EN is and how to check it

PP5V_S0_ALT_AUD_LDO_EN is an enable signal for the alternate audio LDO on the 5V S0 rail; the S0 suffix means it belongs to the running state, and that reading is from the name, not from a schematic. The only known-good reading here is diode OL, with no stated condition, and there is no known-good voltage for it. Check it unpowered in diode mode to ground, then measure the voltage with the board powered in S0. A reading far from OL in diode mode would suggest a low-resistance path on that net, but one reading isn't proof of a bad part.

PP5V_S0_CPUVR_VDD0.44415.000–
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD — reference note

  • What it is: a 5 V rail in the S0 (running) state, from its name. "CPUVR" suggests it feeds the CPU voltage-regulator circuitry, but that's general reading of the name, not confirmed from board data.
  • Known-good readings (community guide): diode 0.4441 to ground, and 5.000 V with the board powered in S0. No condition is recorded with these values.
  • How to check: with power off and the adapter and battery disconnected, measure diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing or low voltage with a normal diode reading points upstream, at the rail's enable or source. No known-good resistance reading for this rail.
PP5V_S0_FET_R0.44––
AI: what PP5V_S0_FET_R is and how to check it

PP5V_S0_FET_R is a 5V rail in the S0 (running) state, judging from its name; the "_FET_R" suffix suggests it's the switched side of a FET that enables the rail. The only known-good reading here is diode mode 0.44 to ground, with no condition noted; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from PP5V_S0_FET_R to ground and compare with 0.44.
  • Then power the board and measure the voltage on the rail; the data gives no expected figure, so compare against a matching rail or a known-good board.

A diode reading far below 0.44 usually points to a short or a leaky part on that rail; a reading far above it can mean an open trace or a missing component. A missing voltage with a normal diode reading points upstream, at the FET's enable or the rail feeding it. These are general guidelines, not confirmed from this board's data.

PPHV_S0SW_LCDBKLT0.56324.450–
PPVCC_S0_CPU0.0101.80025.000R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the S0 in the name puts it in the running stage, so it should only come up once the board is fully on. This board's archive lists known-good readings of diode 0.010, voltage 1.800 V and resistance 25.000R, but no condition is recorded for them, so treat them as a guide only. With the board unpowered, measure diode mode from the rail to ground and compare with 0.010; then power up and check the voltage against 1.800 V. There is no known-good value here for how the rail behaves at other startup stages, and a reading far from these usually points to a short or a fault in the CPU supply rather than the CPU itself, but that is a likely cause, not a confirmed one.

PPVCC_S0_CPU_PH10.0101.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.000R
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 — the S0 in the name places it in the running stage, and VCC_CPU_PH1 is the CPU core supply phase 1 (this is from the name, not from a schematic).

Known-good readings from the archive: diode 0.010, voltage 1.800, and resistance 15.00R (1.6GHz 4GB), 15.70R (1.6GHz 8GB), 14.50R (1.8GHz i5 8GB) or 25.000R. These are community values and vary with board state, so treat them as a guide.

To check: power off and unplug, then diode-mode to ground; then apply power and measure the voltage. A diode far from 0.010 or a resistance far below the listed range usually points to a shorted CPU core rail or a failed phase — but a small difference can be normal, so confirm with a second reading before condemning anything.

PPVCC_S0_CPU_PH20.0101.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.000R
AI: what PPVCC_S0_CPU_PH2 is and how to check it

PPVCC_S0_CPU_PH2 is a CPU core power rail in the S0 (running) state, judged from its name. Known-good readings here: diode 0.010, voltage 1.800, and resistance 15.00R (1.6GHz 4GB), 15.70R (1.6GHz 8GB), 14.50R (1.8GHz i5 8GB) or 25.000R — these are community figures and a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from these usually points to a short or a failed CPU power stage, but confirm with a second measurement before replacing anything. No known-good value of other kinds is listed here.

PPVCOMP_S0_CPU0.10––
AI: what PPVCOMP_S0_CPU is and how to check it

PPVCOMP_S0_CPU is a CPU core-related rail; the S0 in its name marks it as a running-state rail, and VCOMP suggests a compensation/reference node rather than a main power rail (that part is general reading of the name, not from board data). The only known-good figure recorded here is a diode reading of 0.10 to ground; there is no known-good voltage or resistance value for it. Check it with the board unpowered in diode mode, red probe on the net and black on ground, then measure the voltage with the board powered and running. A diode reading far from 0.10 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything.

PPVIN_S0_CPUVR_VIN0.13958.500–
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN — the name indicates the input supply to the CPU voltage regulator, active in the S0 (running) state. From the readings archive, the known-good values are diode 0.1395 to ground and 8.500 V with power applied; no condition is recorded for either.

  • Check it unpowered in diode mode, red probe to ground, black to the rail; then power the board and measure the voltage.
  • A diode reading far below 0.1395 suggests a short or leaky part on the rail; a much higher or open reading suggests a broken feed or open component.
  • A voltage well under 8.500 V with the board in S0 points to a missing or loaded input supply rather than the CPU VR itself.

These are community readings and vary with board state, so treat them as a guide. No known-good resistance reading exists here for this rail.

PPVIN_S0SW_LCDBKLT0.4108.600–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail; the S0 in its name marks it as a running-state rail, and SW suggests a switched supply. Known-good readings here are diode 0.410 and voltage 8.600, community-sourced so treat them as a guide. With the board unpowered, measure diode mode from the rail to ground and compare with 0.410; then power up and check the voltage against 8.600. A far-off diode reading usually points to a short or open on the rail, while a low voltage with a good diode reading points upstream to the backlight enable, fuse or MOSFET path; no known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT_FET0.4108.600–
AI: what PPVIN_S0SW_LCDBKLT_FET is and how to check it

PPVIN_S0SW_LCDBKLT_FET — the name indicates the switched input feed to the LCD backlight FET, in the S0 (running) state. Known-good readings here: diode 0.410 and voltage 8.600.

  • Check it unpowered in diode mode to ground; a short or very low reading points to a fault on that feed or its FET.
  • With power applied in S0, expect about 8.6 V. The backlight notes say below 1 V suggests a bad fuse or MOSFET, and around 8.4 V means checking the enable on U7701 pin 3 and BKL_PWM.
  • No known-good resistance value is recorded for this rail.

These are community readings and vary with board state, so treat them as a guide rather than a confirmed fault.

PPVIN_S0SW_LCDBKLTFET0.1288.600–
AI: what PPVIN_S0SW_LCDBKLTFET is and how to check it

PPVIN_S0SW_LCDBKLTFET is the switched input feed for the LCD backlight boost circuit, an S0 (running-state) rail judging by the name. Known-good readings here: diode 0.128 to ground and 8.600 V when running; no known-good resistance value is recorded. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and running. A voltage far below about 8.6 V usually points to the backlight supply or its switching FET not turning on, but treat that as a likely cause, not a confirmed one.

PPVMEMIO_S0_CPU0.130–258.92R
AI: what PPVMEMIO_S0_CPU is and how to check it

PPVMEMIO_S0_CPU — the name indicates a memory I/O rail for the CPU, active in the S0 (running) state. Known-good readings for this board: diode 0.130 and resistance 258.92R; no known-good voltage reading here.

  • With the board unpowered, measure diode mode from the rail to ground and compare against 0.130.
  • Then power the board and measure the rail voltage; the archive has no expected value, so compare with a known-good board.
  • A reading far from 0.130 in diode mode usually points to a short or a damaged load on the rail, but one reading alone doesn't confirm a bad part.
PPVOUT_S0_PCH_DCPRTC0.70––
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it

PPVOUT_S0_PCH_DCPRTC — the name marks it as an S0 (running-state) rail feeding the PCH's RTC/DC power domain; that reading is from the name, not from a schematic.

  • Known-good: diode 0.70 to ground. No known-good voltage is recorded here.
  • Check: board unpowered, meter in diode mode, black probe on ground, red on the rail; then repeat in voltage mode with power applied.
  • A diode reading well below 0.70 suggests a partial short on that rail; a reading far above it suggests an open path. One reading alone doesn't condemn a part — confirm with a second measurement before replacing anything.

Repair notes

Backlight

Diagnosing

Check your voltage on backlight output. If below 1V probably a bad fuse or MOSFET. If 8.4V check EN signal on U7701 pin 3, if present, check BKL_PWM, if > 1V then replace U7701

Overview

Summary

The Macbook 820-00165 / A1466 generally is a well behaved board but does have some signature quirks. Always use a genuine magsafe 2 power brick else you will get a no-boot situation and you'll be chasing your tail for days.

Power Rails

Missing PM_SLP_S4_L

Missing PM_SLP_S4_L can sometimes be diagnosed by going through and ensuring all the following signals are present; PPVRTC_G3H RTC_RESET_L SRTCRST_L PCH_INTVRMEN PCH_DSWVRMEN PCH_CLK32K_RTCX1 PP3V3_S5 PM_DSW_PWRGD PP3V3_SUS PM_BATLOW_L PM_RSMRST_L PM_PWRBTN_L Remove R8111, if the board powers up then the fault is with the IMC most likely, non-fixable, or might be U7400. Usually is a dead CPU IMC. Check PP3V3_S5_AVREF_SMC in resistance mode (80~100K) / diode (0.6V). If shorted or partial short, may be something other than IMC.

Power Sequence

G3 to S3

G3 STATE PPDCIN_G3H = 3V Magsafe Detects 68kOhm impedance PPDCIN_G3H >= 14.5V Air 16.5-20V Pro DCIN_ISOL_GATE_R = 6.8V PPDCIN_ISOL >= 14.5V Air 16.5-20V Pro PP3V42_G3H = 3.425V CHGR_ACIN >= 3.3V CHGR_DCIN >= 14.5V Air 16.5-20V Pro PPVRTC_G3H = 3.3V SMC_LSOC_RST_L = 3.42V SMBUS_SMC_5_G3_SCL = 3.42V SMBUS_SMC_5_G3_SCL = 3.42V PP5V1_CHGR_VDD = 5.5V PCH_DSWVRMEN = 3.3V PCH_CLK32K_RTCX1 = 32kHz PCH_SRTCRST_L = 3.3V SMC_ONOFF_L = 3.42V PP3V3_S5_AVREF_SMC = 3.3V SMC_BC_ACOK = 3.42V PCH_INTRUDER_L = 3.3V PCH_INTVRMEN = 3.3V RTC_RESET_L = 3.3V SMC_RESET_L = 3.42V PP3V3_S5_SMC_VDDA = 3.42V (diode mode should NOT read OL with inductor removed PPBUS_G3H = 8.2V Air 12.2V Pro SMBUS "5" is the communication SMC -> Charger IC PPBUS_G3H = 8.56V Air 12.56V Pro (asserts running SMC) SMC_PM_G2_EN = 3.42V SYS_ONEWIRE 3.42V (green MagSafe -> 2s -> orange MagSafe) P3V3S5_EN_R = 3.3V PP5V_S5 = 5V P5VP3V3_VREG3 = 3.3V PP3V3_S5 = 3.3V SPIROM_USE_MLB = 3.3V PM_PWRBTN_L = 3.3V [n:S5_PWRGD = 3.42V] PM_BATLOW_L = 3.3V (Genuine MagSafe) S5 STATE WORKING NORMALLY SMC_ADAPTER_EN = 3.42V PM_DSW_PWRGD = 3.42V PM_SLP_SUS_L = 3.3V -> Deep State DCINVSENS_EN_L = 0V SMC_DCIN_VSENSE >= 2.3V && <= 3.3V (Ignored in SMC Bypass mode) P3V3SUS_EN 3.3V PP3V3_SUS = 3.3V PP1V05_SUS = 1.05V PM_RSMRST_L = 3.3V XDP_PCH_TMS = 1.05V XDP_PCH_TDO = 1.05V XDP_PCH_TDI = 1.05V [n:PM_DLK32K_SUSCLK_R = 32kHz] SMC_CLK32K = 32kHz PM_PWRBTN_L = 0 > 15ms PM_PWRBTN_L = 3.3V PM_SLP_S5_L = 3.3V PM_SLP_S4_L 3.3V S4_PWR_EN 3.3V S4 STATE PP3V3_S4 = 3.3V SMC_SENSOR_PWR_EN = 3.3V S3 STATE

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD0.423.3–
ALL_SYS_PWRGD_Rol0–
AP_CLKREQ_L0.433.200–
AP_CLKREQ_Q_L0.463.200–
AP_CLKREQ_R_L0.433.200–
AP_PCIE_DEV_WAKE0.58––
AP_PCIE_WAKE_L0.52––
AP_RESET_CONN_L0.463.300–
AP_RESET_CONN_R_L0.453.300–
AP_RESET_L0.423.200–
AP_S0IX_WAKE_L0.49––
AP_S0IX_WAKE_SEL0.50––
AUD_PWR_EN0.583.200–
AUD_SPI_CLK0.49––
AUD_SPI_CS_L0.49––
AUD_SPI_MISO0.49––
AUD_SPI_MOSI0.49––
BKL_EN0.7 Backlight driver off0.52.8–
BKL_FAULT0.56––
BKL_FLTR0.56––
BKL_FSET0.50–
BKL_ISEN10.6090.488–
BKL_ISEN20.610––
BKL_ISEN30.610––
BKL_ISEN40.605––
BKL_ISEN50.607––
BKL_ISEN60.608––
BKL_ISET0.5–21.5K
BKL_PWM0.53.000–
BKL_SCL0.513.3–
BKL_SDA0.503.300–
BKL_VSYNC_R0.56––
BKLT_PLT_RST_L0.5843.30–
BMON_COMP_FB0.68––
BMON_COMP_OUT0.69––
BMON_COMP_VREF0.69––
BMON_IOUT0.69––
BMON_IOUT_DOL––
BMON_IOUT_R0.69––
BT_PWRRST_L0.49––
BT_WAKE0.77––
CAM_DEBUG_RESET_L0.75––
CAM_GPIO30.75––
CAM_JTAG_SRST_L0.76––
CAM_PCIE_RESET_L0.45––
CAM_PCIE_WAKE_L0.51––
CAM_PWR_SEL0.81––
CAM_RAMCFG00.75––
CAM_RAMCFG10.75––
CAM_RAMCFG20.75––
CAM_SENSOR_WAKE_L0.80––
CAM_SENSOR_WAKE_L_CONN0.0067––
CAM_TEST_MODE0.75––
CAM_TEST_OUT0.81––
CAM_UARTCTS0.75––
CAM_UARTRXD0.75––
CAM_XTAL_FREQ0.75––
CAM_XTAL_SEL0.75––
CAMERA_CLKREQ_L0.46––
CAMERA_PWR_EN0.49––
CAMERA_PWR_EN_PCH0.49––
CHGR_ACIN0.54.344K
CHGR_AGATE0.60–
CHGR_AGATE_DIVOL––
CHGR_AMON0.70.15–
CHGR_BGATE0.645––
CHGR_BMON0.70–
CHGR_BOOT0.513–
CHGR_CELL0.050–
CHGR_CSI_N0.68.6–
CHGR_CSI_P0.6154––
CHGR_CSI_R_N0.6016.500–
CHGR_CSI_R_P0.6016.500–
CHGR_CSO_N0.13016.4–
CHGR_CSO_P0.130––
CHGR_CSO_R_N0.138.600–
CHGR_CSO_R_P0.138.600–
CHGR_DCIN0.616.500–
CHGR_DCIN_DOL––
CHGR_ICOMP0.71.6–
CHGR_ICOMP_ROL––
CHGR_LGATE0.41.7–
CHGR_PHASE0.1378.6–
CHGR_RST_L0.5––
CHGR_SGATE0.60–
CHGR_SGATE_DIVOL––
CHGR_UGATE0.5––
CHGR_VCOMP0.71.3–
CHGR_VCOMP_ROL––
CHGR_VFRQ0.40–
CHGR_VNEG0.51.4–
CHGR_VNEG_ROL––
CLK25M_CAM_CLKN0.79––
CLK25M_CAM_CLKP0.45––
CLK25M_CAM_XTALNOL––
CLK25M_CAM_XTALPOL––
CLK25M_CAM_XTALP_ROL––
CPU_CATERR_L0.28––
CPU_CFG_RCOMP0.05––
CPU_CFG<0>0.3312––
CPU_CFG<1>0.3324––
CPU_CFG<2>0.3317––
CPU_CFG<3>0.3312––
CPU_CFG<4>0.3103––
CPU_CFG<5>0.3297––
CPU_CFG<6>0.3305––
CPU_CFG<7>0.3281––
CPU_CFG<8>0.3288––
CPU_CFG<9>0.3308––
CPU_CFG<10>0.3294––
CPU_CFG<11>0.3327––
CPU_CFG<12>0.3281––
CPU_CFG<13>0.3272––
CPU_CFG<14>0.3288––
CPU_CFG<15>0.3274––
CPU_CFG<16>0.3301––
CPU_CFG<17>0.3294––
CPU_CFG<18>0.3308––
CPU_CFG<19>0.3308––
CPU_DIMM_VREFCA0.80––
CPU_DIMMA_VREFDQ0.81––
CPU_DIMMB_VREFDQ0.80––
CPU_MEM_VREFCA_A_ISOL0.46––
CPU_MEM_VREFCA_B_ISOL0.46––
CPU_MEM_VREFDQ_A_ISOL0.44––
CPU_MEM_VREFDQ_B_ISOL0.45––
CPU_MEMVTT_PWR_EN_LSVDDQ0.33––
CPU_OPI_RCOMP0.05––
CPU_PECI0.36––
CPU_PECI_R0.32––
CPU_PROCHOT_L0.201.045–
CPU_PROCHOT_R_L0.22––
CPU_PWR_DEBUG0.2573––
CPU_PWRGD0.351.050–
CPU_RTN0.0013––
CPU_SM_RCOMP<0>0.17––
CPU_SM_RCOMP<1>0.12––
CPU_SM_RCOMP<2>0.10––
CPU_THRMTRIP_3V30.73––
CPU_VCCSENSE_N0.01––
CPU_VCCSENSE_P0.00––
CPU_VCCSENSE_P_R0.01––
CPU_VCCSENSE_P_RCOL––
CPU_VCCST_PWRGD0.53––
CPU_VIDALERT_L0.1943––
CPU_VIDALERT_R_L0.26––
CPU_VIDSCLK0.201.045–
CPU_VIDSCLK_R0.19––
CPU_VIDSOUT0.201.045–
CPU_VIDSOUT_R0.19––
CPU_VR_EN0.31771.050–
CPU_VR_READY0.5707––
CPUBMONSNS_ALERT_L0.75––
CPUTHMSNS_ADDR_SEL0.00––
CPUTHMSNS_ALERT_L0.57––
CPUTHMSNS_D2_N0.74––
CPUTHMSNS_D2_P0.74––
CPUTHMSNS_DUR_SEL0.76––
CPUTHMSNS_TH_SEL0.76––
CPUVR_BOOT10.60––
CPUVR_BOOT1_RC0.60––
CPUVR_BOOT20.59––
CPUVR_BOOT2_RC0.59––
CPUVR_COMP0.60311.300–
CPUVR_COMP_RCOL––
CPUVR_DRSEL0.0003––
CPUVR_FB0.57531.800–
CPUVR_FB_RCOL––
CPUVR_FB20.61721.800–
CPUVR_FCCM0.59725.000–
CPUVR_IMON0.6118––
CPUVR_ISEN10.62231.800–
CPUVR_ISEN20.6221––
CPUVR_ISNS1_N0.0101.80025.000R
CPUVR_ISNS1_N_R0.65––
CPUVR_ISNS1_P0.0101.80025.000R
CPUVR_ISNS1_P_R0.63––
CPUVR_ISNS2_N0.0101.80025.000R
CPUVR_ISNS2_P0.0101.80025.000R
CPUVR_ISUM_IOUT0.75––
CPUVR_ISUM_R_N0.78––
CPUVR_ISUM_R_P0.78––
CPUVR_ISUMN0.01––
CPUVR_ISUMN_R0.261.800–
CPUVR_ISUMN_RC0.86––
CPUVR_ISUMP0.481.800–
CPUVR_LGATE10.43––
CPUVR_LGATE20.42––
CPUVR_NTC0.62092.000–
CPUVR_NTC_ROL––
CPUVR_PGOOD_R0.703.300–
CPUVR_PH2_SNUBOL––
CPUVR_PHASE10.011.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.000R
CPUVR_PHASE20.011.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.00r
CPUVR_PROG10.6139––
CPUVR_PROG20.6112––
CPUVR_PROG30.6182––
CPUVR_PWM10.60741.100–
CPUVR_PWM20.6072––
CPUVR_SLOPE0.6131––
CPUVR_UGATE10.62––
CPUVR_UGATE20.61––
CPUVRSNS_ADDR_SEL0.74––
CPUVSENSE_IN0.01––
DBGLED_S0I3_DOL––
DBGLED_S3_DOL––
DBGLED_S4_DOL––
DCIN_ISOL_GATE0.796.830–
DCIN_ISOL_GATE_R1.8706.830–
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.47––
DDRREG_1V8_VREF0.61––
DDRREG_DRVH0.598––
DDRREG_DRVL0.460––
DDRREG_EN0.52––
DDRREG_FB0.67––
DDRREG_LL0.128––
DDRREG_MODE0.51––
DDRREG_PGOOD0.46––
DDRREG_TRIP0.73––
DDRREG_VBST0.61––
DDRREG_VBST_RC0.62––
DDRREG_VDDQSNS0.23––
DDRREG_VDDQSNS_R0.26––
DDRREG_VTTSNS0.12––
DP_A_LSX_ML_N<1>0.74––
DP_A_LSX_ML_P<1>0.74––
DP_INT_AUX_CH_C_NOL––
DP_INT_AUX_CH_C_Pol––
DP_INT_AUXCH_C_N0.314––
DP_INT_AUXCH_C_P0.315––
DP_INT_HPD0.78––
DP_INT_HPD_CONN0.78––
DP_INT_ML_C_N<0>0.312––
DP_INT_ML_C_P<0>0.313––
DP_INT_ML_N<0>OL––
DP_INT_ML_P<0>OL––
DP_TBTPA_AUXCH_C_N0.55––
DP_TBTPA_AUXCH_C_P0.58––
DP_TBTPA_AUXCH_N0.80––
DP_TBTPA_AUXCH_P0.80––
DP_TBTPA_HPD0.78––
DP_TBTPA_ML_C_N<1>0.32––
DP_TBTPA_ML_N<1>0.75––
DP_TBTPA_ML_P<1>0.75––
DP_TBTPB_HPD0.79––
DP_TBTSNK0_AUXCH_C_N0.420––
DP_TBTSNK0_AUXCH_C_P0.418––
DP_TBTSNK0_AUXCH_N0.558––
DP_TBTSNK0_AUXCH_P0.599––
DP_TBTSNK0_DDC_CLK0.59––
DP_TBTSNK0_DDC_DATA0.63––
DP_TBTSNK0_HPD0.58––
DP_TBTSNK0_ML_C_N<0>0.30––
DP_TBTSNK0_ML_C_N<1>0.315––
DP_TBTSNK0_ML_C_N<2>0.315––
DP_TBTSNK0_ML_C_N<3>0.314––
DP_TBTSNK0_ML_C_P<0>0.30––
DP_TBTSNK0_ML_C_P<1>0.000––
DP_TBTSNK0_ML_C_P<2>0.315––
DP_TBTSNK0_ML_C_P<3>0.315––
DP_TBTSNK0_ML_N<0>0.57––
DP_TBTSNK0_ML_N<1>0.565––
DP_TBTSNK0_ML_N<2>0.566––
DP_TBTSNK0_ML_N<3>0.567––
DP_TBTSNK0_ML_P<0>0.56––
DP_TBTSNK0_ML_P<1>0.564––
DP_TBTSNK0_ML_P<2>0.565––
DP_TBTSNK0_ML_P<3>0.565––
DP_TBTSNK1_AUXCH_C_N0.41––
DP_TBTSNK1_AUXCH_C_P0.41––
DP_TBTSNK1_AUXCH_N0.558––
DP_TBTSNK1_AUXCH_P0.594––
DP_TBTSNK1_DDC_CLK0.582––
DP_TBTSNK1_DDC_DATA0.611––
DP_TBTSNK1_HPD0.56––
DP_TBTSNK1_ML_C_N<0>0.312––
DP_TBTSNK1_ML_C_N<1>0.30––
DP_TBTSNK1_ML_C_N<2>0.313––
DP_TBTSNK1_ML_C_N<3>0.314––
DP_TBTSNK1_ML_C_P<0>0.316––
DP_TBTSNK1_ML_C_P<1>0.315––
DP_TBTSNK1_ML_C_P<2>0.315––
DP_TBTSNK1_ML_C_P<3>0.30––
DP_TBTSNK1_ML_N<0>0.567––
DP_TBTSNK1_ML_N<1>0.566––
DP_TBTSNK1_ML_N<2>0.590––
DP_TBTSNK1_ML_N<3>0.568––
DP_TBTSNK1_ML_P<0>0.572––
DP_TBTSNK1_ML_P<1>0.567––
DP_TBTSNK1_ML_P<2>0.570––
DP_TBTSNK1_ML_P<3>0.560––
DP_TBTSRC_HPD0.56––
EDP_BKLT_EN0.5743.30–
EDP_BKLT_PWM0.541.600–
EDP_PANEL_PWR0.61––
ENET_LOW_PWR0.58––
ENET_MEDIA_SENSE0.49––
ENETSD_CLKREQ_L0.48––
FAN_RT_PWM0.79––
FAN_RT_TACHOL––
FINSTACKSNS_ALERT_L0.60––
FW_CLKREQ_L0.48––
GND0––
GND_CAM_PVSSD0.00––
GND_DDRREG_SGND0.00––
GND_P5VP3V3_SGND0.00––
HDA_BIT_CLK0.43––
HDA_BIT_CLK_R0.39––
HDA_RST_L0.43––
HDA_RST_R_L0.39––
HDA_SDIN00.39––
HDA_SDOUT0.43––
HDA_SDOUT_R0.39––
HDA_SYNC0.43––
HDA_SYNC_R0.39––
HDD_PWR_EN0.59––
HDMITBTMUX_FLAG0.59––
HDMITBTMUX_LATCH0.580––
HDMITBTMUX_SEL_TBT0.49––
HS_COMP_FB0.69––
HS_COMP_OUT0.69––
HS_COMP_VREF0.68––
HS_IOUT_DOL––
HS_IOUT_R0.70––
HS_OTHER_IOUTOL––
HSIOFET_DISCHARGEOL––
HSIOFET_DRV_HOL––
HSIOFET_DRV_LOL––
HSIOFET_ENOL––
HSIOFET_EN_LOL––
I2C_CAM_SCK0.7595––
I2C_CAM_SDA0.7596––
I2C_CAM_SMBDBG_CLK0.77––
I2C_CAM_SMBDBG_DAT0.77––
I2C_TCON_SCL_R0.73––
I2C_TCON_SDA_R0.73––
INLET_THMSNS_D1_N0.74––
INLET_THMSNS_D1_P0.74––
ISNS_1V2_IOUT0.70––
ISNS_1V2_S3_N0.278––
ISNS_1V2_S3_P0.278––
ISNS_1V05_S0_NOL––
ISNS_1V05_S0_POL––
ISNS_AIRPORT_N0.523.300–
ISNS_AIRPORT_P0.523.300–
ISNS_CAMERA_IOUTOL––
ISNS_CAMERA_NOL––
ISNS_CPUDDR_IOUTOL––
ISNS_CPUDDR_NOL––
ISNS_CPUDDR_POL––
ISNS_HS_COMPUTING_IOUT0.70––
ISNS_HS_COMPUTING_N0.1378.600–
ISNS_HS_COMPUTING_P0.1378.600–
ISNS_HS_GAIN_N0.64––
ISNS_HS_GAIN_N_R0.65––
ISNS_HS_GAIN_OUT0.70––
ISNS_HS_GAIN_OUT_R0.70––
ISNS_HS_GAIN_P0.39––
ISNS_HS_GAIN_P_R0.37––
ISNS_HS_OTHER_NOL––
ISNS_HS_OTHER_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_NOL––
ISNS_LCDBKLT_POL––
ISNS_P3V3_S0_IOUTOL––
ISNS_P3V3_S0_NOL––
ISNS_P3V3_S0_POL––
ISNS_P3V3S5_IOUTOL––
ISNS_P3V3S5_N0.3603.3000.000R
ISNS_P3V3S5_P0.3603.300–
ISNS_P5VSSD_IOUT0.70––
ISNS_P5VWLAN_IOUTOL––
ISNS_PANEL_IOUTOL––
ISNS_PANEL_NOL––
ISNS_PANEL_POL––
ISNS_SSD_N0.513.300–
ISNS_SSD_P0.513.300–
JTAG_ISP_TDO0.46––
JTAG_TBT_TDO0.51––
JTAG_TBT_TMS0.61––
JTAG_TBT_TMS_PCH0.49––
KBDLED_ANODE0.6210––
KBDLED_FB0.0068––
KBDLED_SW0.430––
LCD_IRQ_L0.49––
LCD_PSR_EN0.50––
LCDBKLT_BOOST0.4108.50–
LCDBKLT_DISABLE0.595––
LCDBKLT_EN_DIV_LOL2.85–
LCDBKLT_EN_L1.25––
LED_RETURN_10.640.5–
LED_RETURN_20.6298––
LED_RETURN_30.6299––
LED_RETURN_40.6262––
LED_RETURN_50.6265––
LED_RETURN_60.6275––
LPC_AD_R<0>0.49––
LPC_AD_R<1>0.49––
LPC_AD_R<2>0.49––
LPC_AD_R<3>0.49––
LPC_AD<0>0.52––
LPC_AD<1>0.52––
LPC_AD<2>0.52––
LPC_AD<3>0.52––
LPC_CLK24M_SMC0.44––
LPC_CLK24M_SMC_R0.41––
LPC_FRAME_L0.52––
LPC_FRAME_R_L0.49––
LPC_PWRDWN_L0.60––
LPC_SERIRQ0.49––
MAX98300_R_N0.60––
MAX98300_R_P0.60––
MCP_DC_A4OL––
MCP_DC_A60OL––
MCP_DC_A62OL––
MCP_DC_AV1OL––
MCP_DC_AW1OL––
MCP_DC_AW63OL––
MCP_DC_AY60OL––
MCP_DC_B2OL––
MCP_EDP_RCOMP0.12––
MEM_A_CAA<3>0.156––
MEM_A_CAA<4>0.157––
MEM_A_CAA<5>0.157––
MEM_A_CAB<4>0.156––
MEM_A_CAB<9>0.157––
MEM_A_CKE<0>0.173––
MEM_A_CKE<1>0.175––
MEM_A_CKE<2>0.175––
MEM_A_CKE<3>0.175––
MEM_A_CLK_N<0>0.144––
MEM_A_CLK_N<1>0.144––
MEM_A_CLK_P<0>0.145––
MEM_A_CLK_P<1>0.144––
MEM_A_CS_L<1>0.174––
MEM_A_ODT<0>0.174––
MEM_A_ZQ<0>0.24––
MEM_A_ZQ<1>0.24––
MEM_A_ZQ<2>0.25––
MEM_A_ZQ<3>0.25––
MEM_B_CAA<2>0.157––
MEM_B_CAA<4>0.157––
MEM_B_CAA<5>0.156––
MEM_B_CAB<4>0.156––
MEM_B_CAB<9>0.157––
MEM_B_CKE<0>0.174––
MEM_B_CKE<1>0.174––
MEM_B_CKE<2>0.175––
MEM_B_CKE<3>0.175––
MEM_B_CLK_N<0>0.144––
MEM_B_CLK_N<1>0.145––
MEM_B_CLK_P<0>0.144––
MEM_B_CLK_P<1>0.144––
MEM_B_CS_L<0>0.172––
MEM_B_CS_L<1>0.173––
MEM_B_ODT<0>0.173––
MEM_B_ZQ<0>0.25––
MEM_B_ZQ<1>0.25––
MEM_B_ZQ<2>0.24––
MEM_B_ZQ<3>0.24––
MEM_CAM_CKE0.438––
MEM_CAM_CKE_ROL––
MEM_CAM_CLK_N0.409––
MEM_CAM_CLK_P0.408––
MEM_CAM_ODT0.67––
MEM_CAM_RESET_L0.42––
MEM_CAM_ZQ_DDR0.24––
MEM_CAM_ZQ_S20.24––
MEM_VREFCA_A_RC0.03––
MEM_VREFCA_B_RC0.00––
MEM_VREFDQ_A_RC0.03––
MEM_VREFDQ_B_RC0.03––
MEMVTT_PWR_EN0.51––
MIPI_CLK_CONN_N0.3968––
MIPI_CLK_CONN_P0.3971––
MIPI_CLK_N0.40––
MIPI_CLK_P0.41––
MIPI_DATA_CONN_N0.3928––
MIPI_DATA_CONN_P0.3919––
MIPI_DATA_N0.40––
MIPI_DATA_P0.41––
N108527691–25.000–
ODD_PWR_EN_L0.58––
P0V9SLPDDR_SW00.08–51.00R
P0V9SLPDDR_SW10.08–51.00R
P1V1SLPS2R_SW00.27–2.80k
P1V1SLPS2R_SW10.27–2.80k
P1V2_CAM_SRVLXC_PHASE0.281.200–
P1V05_DIV_VMONOL––
P1V5_DIV_VMONOL––
P1V05_EN_DOL––
P1V05_S0_VREF0.61––
P1V5CODEC_EN_D1.683.200–
P1V05S0_AGND0.00––
P1V05S0_BOOT_RC0.61––
P1V05S0_DRVH0.58––
P1V05S0_DRVH_R0.65––
P1V05S0_DRVL0.44––
P1V05S0_EN0.45––
P1V05S0_FB0.66––
P1V05S0_IOUTOL––
P1V05S0_LL0.112––
P1V05S0_LL_SNUBOL––
P1V05S0_MODE0.51––
P1V05S0_PGOOD0.47––
P1V05S0_TRIP0.73––
P1V05S0_VBST0.60––
P1V05S0_VDDQSNS0.14––
P1V05S0_VDDQSNS_R0.15––
P1V05S0_VTT0.58––
P1V05S0_VTTREF0.48––
P1V5S0SW_AUDIO_EN0.683.200–
P1V05S3_EN0.48––
P1V05TBT_SW0.15––
P1V05VSENSE_IN0.194––
P1V8S3_EN0.48––
P1V8S3_FB0.76––
P1V8S3_PGOOD0.533.300–
P1V8S3_SW0.381.800–
P1V35_CAM_SRVLXD_PHASE0.261.300–
P3V3_S5_COMP20.73––
P3V3_S5_COMP2_ROL––
P3V3_S5_CSN20.353.300–
P3V3_S5_CSP21.263.300–
P3V3_S5_CSP2_R0.353.300–
P3V3_S5_DRVH0.893.300–
P3V3_S5_DRVL0.53––
P3V3_S5_LL0.35––
P3V3_S5_REG_L0.363.300–
P3V3_S5_REG_SNUBOL––
P3V3_S5_RF0.57––
P3V3_S5_VBST0.62––
P3V3_S5_VBST_R0.54––
P3V3_S5_VFB20.56––
P3V3_S5_VFB2_R0.36––
P3V3_S5_VFB2_XW0.36––
P3V3_SD_FET_RAMP0.70––
P3V3S0_EN0.6783.300–
P3V3S0_EN_D0.70––
P3V3S0SW_SSD_FET_RAMP0.693.300–
P3V3S3_EN0.48––
P3V3S5_EN_R0.523.300–
P3V3SSD_VMON0.470.990–
P3V3SUS_EN0.563.300–
P3V3WLAN_VMON0.450.989–
P3V42G3H_BOOST0.62127.25–
P3V42G3H_FB0.71131.25–
P3V42G3H_SHDN_L0.348616.22–
P3V42G3H_SW0.3203.40013.000k
P5V_DIV_VMONOL––
P5V_S4RS3_COMP10.73––
P5V_S4RS3_COMP1_ROL––
P5V_S4RS3_CSN10.43––
P5V_S4RS3_CSP11.19––
P5V_S4RS3_CSP1_R0.435.000–
P5V_S4RS3_DRVH0.97––
P5V_S4RS3_DRVL0.53––
P5V_S4RS3_FUNC0.00––
P5V_S4RS3_LL0.42––
P5V_S4RS3_REG_L0.445.000–
P5V_S4RS3_REG_SNUBOL––
P5V_S4RS3_VBST0.62––
P5V_S4RS3_VBST_R0.63––
P5V_S4RS3_VFB10.56––
P5V_S4RS3_VFB1_R0.45––
P5V_S4RS3_VFB1_XW0.44––
P5V1_FBOL––
P5V1_SWOL––
P5VP3V3_SKIPSEL0.471.900–
P5VP3V3_VREF20.471.900–
P5VP3V3_VREG30.553.200–
P5VS0_EN0.46––
P5VS0_FET_RAMP0.61––
P5VS4RS3_EN0.483.300–
P5VS4RS3_EN_DOL––
P5VS4RS3_EN_R0.483.300–
P5VS4RS3_EN_RC0.483.300–
P5VS4RS3_PGOOD0.47––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.47––
PBUSVSENS_EN_L_DIVOL––
PCA9557D_RESET_L0.49––
PCH_BT_UART_CTS_L0.49––
PCH_BT_UART_D2R0.506––
PCH_BT_UART_R2D0.49––
PCH_BT_UART_RTS_L0.49––
PCH_CLK24M_XTALIN0.78––
PCH_CLK24M_XTALOUT0.78––
PCH_CLK24M_XTALOUT_R0.78––
PCH_CLK32K_RTCX10.46––
PCH_DIFFCLK_BIASREF0.69––
PCH_DSWVRMEN0.783.200–
PCH_HSIO_PWR_EN0.473.300–
PCH_I2C1_SCL0.59––
PCH_I2C1_SDA0.59––
PCH_INTRUDER_L0.793.000–
PCH_INTVRMEN0.793.300–
PCH_JTAGX0.05––
PCH_OPI_COMP0.05––
PCH_PCIE_RCOMP0.76––
PCH_PM_SLP_S0_L0.453.300–
PCH_SATA_RCOMP0.76––
PCH_SATALED_L0.59––
PCH_SMBALERT_L0.60––
PCH_SML1ALERT_L0.61––
PCH_SRTCRST_L0.783.300–
PCH_STRP_TOPBLK_SWP_L0.50––
PCH_SUSACK_L0.58––
PCH_SUSWARN_L0.59––
PCH_TBT_PCIE_RESET_L0.56––
PCH_TCO_TIMER_DISABLE0.48––
PCH_TD_IREF0.78––
PCH_TESTLOW_AK80.78––
PCH_TESTLOW_AL80.78––
PCH_TESTLOW_C340.79––
PCH_TESTLOW_C350.79––
PCH_UART1_CTS_L0.49––
PCH_UART1_RXD0.49––
PCH_UART1_TXDOL––
PCH_USB_RBIAS0.03––
PCIE_AP_D2R_N0.37––
PCIE_AP_D2R_P0.37––
PCIE_AP_R2D_C_N0.366––
PCIE_AP_R2D_C_P0.366––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CAMERA_D2R_C_N0.39––
PCIE_CAMERA_D2R_C_P0.39––
PCIE_CAMERA_D2R_N0.390––
PCIE_CAMERA_D2R_P0.390––
PCIE_CAMERA_R2D_C_N0.377––
PCIE_CAMERA_R2D_C_P0.377––
PCIE_CAMERA_R2D_N0.42––
PCIE_CAMERA_R2D_P0.42––
PCIE_CLK100M_AP_N0.28––
PCIE_CLK100M_AP_P0.28––
PCIE_CLK100M_CAMERA_C_N0.78––
PCIE_CLK100M_CAMERA_C_P0.78––
PCIE_CLK100M_CAMERA_N0.303––
PCIE_CLK100M_CAMERA_P0.301––
PCIE_CLK100M_SSD_N0.280.000–
PCIE_CLK100M_SSD_P0.280.000–
PCIE_SSD_D2R_N<0>0.36––
PCIE_SSD_D2R_N<1>0.36––
PCIE_SSD_D2R_N<2>0.36––
PCIE_SSD_D2R_N<3>0.37––
PCIE_SSD_D2R_P<0>0.37––
PCIE_SSD_D2R_P<1>0.37––
PCIE_SSD_D2R_P<2>0.36––
PCIE_SSD_D2R_P<3>0.37––
PCIE_SSD_R2D_C_N<0>0.3600.526–
PCIE_SSD_R2D_C_N<1>0.3600.515–
PCIE_SSD_R2D_C_N<2>0.3600.519–
PCIE_SSD_R2D_C_N<3>0.360.250–
PCIE_SSD_R2D_C_P<0>0.3600.526–
PCIE_SSD_R2D_C_P<1>0.3600.515–
PCIE_SSD_R2D_C_P<2>0.3600.519–
PCIE_SSD_R2D_C_P<3>0.3600.250–
PCIE_SSD_R2D_N<0>OL––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_N<2>OL––
PCIE_SSD_R2D_N<3>OL––
PCIE_SSD_R2D_P<0>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_SSD_R2D_P<2>OL––
PCIE_SSD_R2D_P<3>OL––
PCIE_WAKE_L0.50––
PDCINVSENS_EN_L_DIVOL7.970–
PDDR_S3_REG_L0.130––
PDDR_S3_REG_SNUBOL––
PLT_RESET_L0.493.300–
PLT_RST_BUF_L0.633.300–
PM_BATLOW_L0.493.300–
PM_CLK32K_SUSCLK_R0.63––
PM_CLKRUN_L0.493.300–
PM_DSW_PWRGD0.733.400–
PM_PCH_PWROK0.663.400–
PM_PCH_SYS_PWROK0.723.400–
PM_PWRBTN_L0.6223.400–
PM_RSMRST_L0.62453.300–
PM_S0_PGOOD0.653.400–
PM_SLP_S0_L0.53.3–
PM_SLP_S3_BUF_L0.453.300–
PM_SLP_S3_L0.53.3–
PM_SLP_S3_R_L0.57––
PM_SLP_S4_L0.4953.3–
PM_SLP_S5_L0.43.3–
PM_SLP_SUS_L0.5833.300–
PM_SYSRST_L0.59––
PM_THRMTRIP_L0.25––
PM_THRMTRIP_R_LOL––
PP0V6_S0_DDRVTT0.1080.6–
PP0V6_S3_MEM_VREFCA_A0.46––
PP0V6_S3_MEM_VREFCA_B0.45––
PP0V6_S3_MEM_VREFDQ_A0.44––
PP0V6_S3_MEM_VREFDQ_B0.43––
PP0V675_CAM_VREF0.67––
PP0V675_MEM_CAM_VREFCA0.53––
PP0V675_MEM_CAM_VREFDQ0.67––
PP1V2_CAM0.271.200–
PP1V2_CAM_PCIE_PVDD_FLT0.34––
PP1V2_CAM_PCIE_VDD_FLT0.34––
PP1V2_CAM_XTALPCIEVDD0.331.200–
PP1V2_S0_SD_AVDD120.26––
PP1V2_S0_SD_VUHS10.42––
PP1V2_S30.1301.2–
PP1V2_S3_SD_DVDD120.26––
PP1V2_S5_SMC_VDDC0.50––
PP1V05_S00.1121.050–
PP1V5_S00.41.5–
PP1V05_S0_PCH_VCC_ICC0.15––
PP1V05_S0_PCH_VCC_ICC_R0.15––
PP1V05_S0_PCH_VCCACLKPLL0.151.040–
PP1V05_S0_PCH_VCCACLKPLL_R0.15––
PP1V05_S0_PCH_VCCAPLL_OPI0.141.000–
PP1V05_S0_REG_R0.112–160.000R
PP1V5_S0SW_AUDIO0.351.500–
PP1V5_S0SW_AUDIO_HDA0.341.500–
PP1V05_S0SW_PCH_HSIO0.221.0500.000R
PP1V05_S0SW_PCH_VCCSATA3PLL0.22–330.000R
PP1V05_S0SW_PCH_VCCUSB3PLL0.231.037–
PP1V05_SUS0.291.050–
PP1V05_TBT0.15––
PP1V05_TBTCIO0.80––
PP1V05_TBTRDV0.12––
PP1V8_CAM0.49––
PP1V8_S30.31.8–
PP1V8_S3_REG_R0.371.800–
PP1V35_CAM0.261.300–
PP1V35_DDR_CLK0.26––
PP3V3_S00.3903.300–
PP3V3_S0_CPUTHMSNS_R0.433.200–
PP3V3_S0_FAN0.37––
PP3V3_S0_FET_R0.37––
PP3V3_S0_SD_AVDD330.41––
PP3V3_S0_SD_CONN0.41––
PP3V3_S0_TBTMLB_ISNS_R0.43––
PP3V3_S0SW_LCD0.5473.300–
PP3V3_S0SW_LCD_R0.5473.300–
PP3V3_S0SW_LCD_UF0.5473.3–
PP3V3_S0SW_SD0.40––
PP3V3_S0SW_SSD0.513.300–
PP3V3_S0SW_SSD_FET_R0.513.300–
PP3V3_S0SW_SSD_FLT0.503.300–
PP3V3_S30.473.300–
PP3V3_S3_FET_R0.47––
PP3V3_S3_VREFMRGN_DAC0.473.300–
PP3V3_S3RS0_CAMERA0.26––
PP3V3_S3RS0_CAMERA_R0.37––
PP3V3_S40.43.300–
PP3V3_S4_FET_R0.38––
PP3V3_S4_IPD0.38000.350 TP+and+KB+Installed3.300–
PP3V3_S4_TBT_F0.38––
PP3V3_S4_TBTAPWR0.453.300–
PP3V3_S4SW_SNS0.503.300–
PP3V3_S4SW_SNS_FET_R0.49––
PP3V3_S50.3353.3–
PP3V3_S5_AVREF_SMC0.603.200–
PP3V3_S5_DBGLEDOL––
PP3V3_S5_REG_R0.3603.300–
PP3V3_S5_SMC_VDDA0.323.400–
PP3V3_S5RS3RS0_SYSCLKGEN0.353.300–
PP3V3_SNS_CPUVR_ADJUST_ISNS0.53––
PP3V3_SUS0.513.300–
PP3V3_SUS_FET_R0.423.300–
PP3V3_TBTLC0.403.300–
PP3V3_TBTRDV0.52––
PP3V3_WLAN0.513.300–
PP3V3_WLAN_R0.523.300–
PP3V3RHV_S4_TBTAPWR0.553.300–
PP3V3RHV_S4_TBTAPWR_F0.57––
PP3V42_G3H0.3200.300 TP+and+KB+Installed3.40.300R
PP3V42_G3H_SMC_SPVSR0.32––
PP5V_S00.4305–
PP5V_S0_ALT_AUD_LDO_ENOL––
PP5V_S0_CPUVR_VDD0.44415.000–
PP5V_S0_FET_R0.44––
PP5V_S3_RTUSB_A_F0.4545.100–
PP5V_S3_RTUSB_A_ILIM0.4545.100–
PP5V_S3_U62100.44––
PP5V_S3RS0_ALSCAM_F0.4486––
PP5V_S4_IPD0.43460.430 TP+and+KB+Installed5.000–
PP5V_S4RS30.4045.000–
PP5V_S50.435–
PP5V1_CHGR_VDD0.45–
PP5V1_CHGR_VDDP0.45–
PP5V5_CHGR_VDDPOL––
PP15V_TBT0.56––
PP18V5_DCIN_ISOL_ROL16.500–
PPBUS_G3H0.13 1.8GHz i5 8GB0.1288.600–
PPBUS_G3H_R0.148.600–
PPBUS_S5_HS_COMPUTING_ISNS0.1288.600–
PPBUS_S5_HS_OTHER_ISNS0.1378.600–
PPCHGR_DCIN_D_R0.6416.500–
PPDCIN_G3H1.98816.500–
PPDCIN_G3H_CHGR0.60016.500–
PPDCIN_G3H_INRUSH0.60016.500–
PPDCIN_G3H_ISOLol16.500150K
PPDDR_S3_REG_R0.130––
PPHV_S0SW_LCDBKLT0.56324.450–
PPVBAT_G3H_CHGR_R0.138.600–
PPVBAT_G3H_CHGR_REG0.13 1.8GHz i5 8GB0.1308.6003.000k
PPVBAT_G3H_CONNOL––
PPVCC_S0_CPU0.0101.80025.000R
PPVCC_S0_CPU_PH10.0101.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.000R
PPVCC_S0_CPU_PH20.0101.80015.00r 1.6GHz 4GB15.70R 1.6GHz 8GB14.50R 1.8GHz i5 8GB25.000R
PPVCOMP_S0_CPU0.10––
PPVIN_G3H_P3V42G3H0.350416.22–
PPVIN_S0_CPUVR_VIN0.13958.500–
PPVIN_S0SW_LCDBKLT0.4108.600–
PPVIN_S0SW_LCDBKLT_FET0.4108.600–
PPVIN_S0SW_LCDBKLTFET0.1288.600–
PPVIN_S4SW_TBTBST_FET0.50––
PPVMEMIO_S0_CPU0.130–258.92R
PPVOUT_S0_PCH_DCPRTC0.70––
PPVOUT_S5_PCH_DCPSUSBYP0.29––
PPVOUT_S5_PCH_DCPSUSBYP_R0.26––
PPVOUT_SW_LCDBKLT_FB0.60––
PPVRTC_G3H0.43.3–
PPVTT_S3_DDR_BUF0.48––
R_AMP_GAIN0.60––
RTC_RESET_L0.783.300–
S0PGD_BJT_GND_R0.09––
S4_PWR_EN0.463.300–
S5_PWR_EN0.543.420–
S5_PWRGD0.563.300–
SD_CD_L0.46––
SD_CONN_CLK0.49––
SD_PWR_EN0.48––
SD_RESET_L0.60––
SD_RTERM0.66––
SD_SPI_CLK0.70––
SD_SPI_CS_L0.71––
SD_SPI_HOLD_LOL––
SD_SPI_MISO0.71––
SD_SPI_MOSI0.70––
SD_SPI_WP_LOL––
SDCLK_CLK25M_X20.56––
SDCLK_CLK25M_X2_R0.58––
SDCONN_CLK0.46––
SDCONN_CLK_L0.50––
SDCONN_CLK_R10.50––
SDCONN_CLK_R20.49––
SDCONN_CMD0.47––
SDCONN_CMD_R0.46––
SDCONN_DATA<0>0.46––
SDCONN_DATA<1>0.46––
SDCONN_DATA<2>0.47––
SDCONN_DATA<3>0.47––
SDCONN_DETECT_L0.46––
SDCONN_R_DATA<0>0.46––
SDCONN_R_DATA<1>0.46––
SDCONN_R_DATA<2>0.47––
SDCONN_R_DATA<3>0.47––
SDCONN_STATE_CHANGE_SAK_L0.41––
SDSCLK_CLK25M_X10.51––
SMBUS_PCH_CLK0.50373.300–
SMBUS_PCH_DATA0.51233.300–
SMBUS_SMC_0_S0_SCL0.708––
SMBUS_SMC_0_S0_SDA0.73––
SMBUS_SMC_1_S0_SCL0.55––
SMBUS_SMC_1_S0_SDA0.55––
SMBUS_SMC_2_S3_SCL0.723.300–
SMBUS_SMC_2_S3_SDA0.723.300–
SMBUS_SMC_3_SCL0.71340.580 TP+and+KB+Installed3.300–
SMBUS_SMC_3_SDA0.71120.580 TP+and+KB+Installed3.300–
SMBUS_SMC_5_G3_SCL0.53.4–
SMBUS_SMC_5_G3_SDA0.53.4–
SMC_1V2S3_ISENSE0.74––
SMC_ADAPTER_EN0.583.400–
SMC_BC_ACOK0.543.4–
SMC_BIL_BUTTON_L0.74––
SMC_BMON_COMP_ALERT_L0.41––
SMC_BMON_DISCRETE_ISENSE0.74––
SMC_BMON_ISENSE0.74––
SMC_CAMERA_ISENSE0.74––
SMC_CLK32K0.64––
SMC_CPU_DBGPWR_RD_L0.72––
SMC_CPU_IMON_ISENSE0.62––
SMC_CPU_ISENSE0.74––
SMC_CPU_VSENSE0.73––
SMC_CPUDDR_ISENSE0.74––
SMC_CPUVR_ADJUST_ISENSE0.71––
SMC_CPUVR_ADJUST_ISENSE_R0.71––
SMC_DCIN_ISENSE0.74––
SMC_DCIN_VSENSE0.74––
SMC_DEBUGPRT_EN_L0.60––
SMC_DEBUGPRT_RX_L0.67––
SMC_DEBUGPRT_TX_L0.68––
SMC_DELAYED_PWRGD0.693.400–
SMC_EXTAL0.76––
SMC_FAN_0_CTL0.74––
SMC_FAN_0_TACH0.74––
SMC_HS_COMP_ALERT_L0.42––
SMC_HS_COMPUTING_ISENSE0.74––
SMC_LCDBKLT_ISENSE0.74––
SMC_LID0.74170.450 TP+and+KB+Installed3.400–
SMC_LRESET_L0.64––
SMC_LSOC_RST_L0.64680.460 TP+and+KB+Installed3.300–
SMC_MANUAL_RST_L0.67––
SMC_ONOFF_L0.63620.640 TP+and+KB+Installed3.400–
SMC_OOB1_D2R_CONN_L0.53––
SMC_OOB1_D2R_L0.683.300–
SMC_OOB1_R2D_CONN_L0.69––
SMC_OOB1_R2D_L0.49––
SMC_OTHER_HI_ISENSE0.74––
SMC_P1V05S0_ISENSE0.74––
SMC_P1V05S0_VSENSE0.73––
SMC_P3V3S0_ISENSE0.74––
SMC_P3V3S5_ISENSE0.75––
SMC_PANEL_ISENSE0.74––
SMC_PBUS_VSENSE0.73––
SMC_PCH_SUSACK_L0.58––
SMC_PCH_SUSWARN_L0.59––
SMC_PECI_L0.74––
SMC_PECI_L_R0.73––
SMC_PM_G2_EN0.523.300–
SMC_PME_S4_DARK_L0.52––
SMC_PME_S4_WAKE_L0.42––
SMC_PME_SDCONN0.49––
SMC_PROCHOT0.74––
SMC_PWRFAIL_WARN_L0.48––
SMC_RESET_L0.503.400–
SMC_RUNTIME_SCI_L0.58––
SMC_RX_L0.74––
SMC_S4_WAKESRC_EN0.74––
SMC_S5_PWRGD_VIN0.74––
SMC_SENSOR_ALERT_L0.45––
SMC_SENSOR_PWR_EN0.66––
SMC_SSD_ISENSE0.74––
SMC_SYS_KBDLED0.65––
SMC_TCK0.73––
SMC_TDI0.74––
SMC_TDO0.74––
SMC_THRMTRIP0.74––
SMC_TMS0.73––
SMC_TOPBLK_SWP_L0.70––
SMC_TX_L0.74––
SMC_VCCIO_CPU_DIV20.73––
SMC_WAKE_L0.74––
SMC_WAKE_SCI_L0.48––
SMC_WIFI_PWR_EN0.423.400–
SMC_WLAN_ISENSE0.74––
SMC_XTAL0.75––
SML_PCH_0_CLK0.59––
SMS_INT_L0.74––
SPI_ALT_CLK0.55––
SPI_ALT_CS_L0.533.300–
SPI_ALT_IO0_MOSI0.53––
SPI_ALT_IO1_MISO0.59––
SPI_ALT_IO2_WP_L0.553.300–
SPI_ALT_IO3_HOLD_L0.55––
SPI_CLK0.51––
SPI_CLK_R0.50––
SPI_CS0_L0.51––
SPI_CS0_R_L0.49––
SPI_DESCRIPTOR_OVERRIDE0.89––
SPI_DESCRIPTOR_OVERRIDE_L0.74––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.48––
SPI_IO<2>0.49––
SPI_IO<3>0.49––
SPI_IO2_R0.503.300–
SPI_IO3_R0.51––
SPI_MISO0.48––
SPI_MISO_R0.503.300–
SPI_MLB_CLK0.54––
SPI_MLB_CS_L0.553.300–
SPI_MLB_IO0_MOSI0.413.300–
SPI_MLB_IO1_MISO0.483.300–
SPI_MLB_IO2_WP_L0.533.300–
SPI_MLB_IO3_HOLD_L0.503.300–
SPI_MLBROM_CS_L0.623.300–
SPI_MOSI0.51––
SPI_MOSI_R0.50––
SPI_SMC_CLK0.54––
SPI_SMC_CS_L0.563.300–
SPI_SMC_MISO0.543.300–
SPI_SMC_MOSI0.56––
SPIROM_USE_MLB0.48––
SPKRAMP_INR_NOL––
SPKRAMP_INR_POL––
SPKRAMP_ROUT_N0.30–400.00k
SPKRAMP_ROUT_P0.402.501.00M
SPKRAMP_SHDN_L0.59––
SSD_BOOT0.57––
SSD_BOOT_ROL––
SSD_CLKREQ_CONN_L0.463.144–
SSD_CLKREQ_L0.42––
SSD_PCIE_SEL_L0.00––
SSD_PWR_EN0.423.200–
SSD_RESET_CONN_L0.473.420–
SSD_RESET_L0.433.270–
SSD_SR_EN_L0.47––
SUS_PGOOD_CT0.6303––
SYS_DETECT_L1.625––
SYS_ONEWIRE0.743.3–
SYS_PWROK_R0.663.400–
SYSCLK_CLK25M_CAMERA0.45––
SYSCLK_CLK25M_TBT0.44––
SYSCLK_CLK25M_TBT_R0.66––
SYSCLK_CLK25M_X10.441.100–
SYSCLK_CLK25M_X20.45––
SYSCLK_CLK25M_X2_R0.45––
TBDTHMSNS_D2_N0.75––
TBDTHMSNS_D2_P0.76––
TBT_A_CIO_SEL0.78––
TBT_A_CONFIG1_BUF0.78––
TBT_A_CONFIG1_RC0.79––
TBT_A_CONFIG2_RC0.79––
TBT_A_D2R_C_N<1>0.75––
TBT_A_D2R_C_P<1>0.75––
TBT_A_D2R1_AUXDDC_N0.73––
TBT_A_D2R1_AUXDDC_P0.73––
TBT_A_DP_PWRDN0.78––
TBT_A_HPD0.80––
TBT_A_HV_EN0.47––
TBT_A_LSRX0.76––
TBT_A_LSTX0.75––
TBT_B_CIO_SEL0.808––
TBT_B_CONFIG1_BUF0.79––
TBT_B_CONFIG2_RC0.78––
TBT_B_DP_PWRDN0.79––
TBT_B_HV_EN0.79––
TBT_B_LSRX0.78––
TBT_BATLOW_L0.78––
TBT_CIO_PLUG_EVENT_L0.521––
TBT_CLKREQ_L0.46––
TBT_DDC_XBAR_EN_L0.79––
TBT_DFT_STRAP_10.55––
TBT_DFT_STRAP_30.55––
TBT_EN_CIO_PWR0.58––
TBT_EN_CIO_PWR_L0.55––
TBT_GPIO20.608––
TBT_GPIO70.59––
TBT_INLET_THM_L0.75––
TBT_MLBBOT_THMSNS_N0.74––
TBT_MLBBOT_THMSNS_P0.74––
TBT_MONOBSN0.16––
TBT_MONOBSP0.17––
TBT_POC_RESET_L0.50––
TBT_PWR_EN0.49––
TBT_PWR_ON_POC_RST_L0.73––
TBT_PWR_REQ_L0.62––
TBT_RBIAS0.78––
TBT_ROM_SECURITY_XOR0.55––
TBT_RSENSE0.00––
TBT_SPI_CLK0.58––
TBT_SPI_CS_L0.64––
TBT_SPI_MISO0.66––
TBT_SPI_MOSI0.55––
TBT_TEST_EN0.10––
TBT_TEST_PWR_GOOD0.65––
TBT_TMU_CLK_OUT0.56––
TBTACONN_1_COL––
TBTACONN_7_COL––
TBTACONN_20_RC0.58––
TBTAPWRSW_ISET_S00.47––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.47––
TBTAPWRSW_ISET_S3_ROL––
TBTAPWRSW_ISET_V3P30.47––
TBTBST_BOOST0.500––
TBTBST_EN_UVLO0.53––
TBTBST_FBXOL––
TBTBST_INTVCC0.56––
TBTBST_PWREN_DIV_LOL––
TBTBST_PWREN_L0.43––
TBTBST_RT0.68––
TBTBST_SHDN_DIV0.47––
TBTBST_SNS10.00––
TBTBST_SNS20.00––
TBTBST_SS0.68––
TBTBST_VC0.69––
TBTBST_VC_RCOL––
TBTBST_VSNS0.56––
TBTBST_VSNS_RCOL––
TBTDP_AUXIO_EN0.799––
TBTMLBSNS_ALERT_L0.58––
TBTROM_HOLD_L0.70––
TBTROM_WP_L0.71––
TBTTHMSNS_D2_R_N0.75––
TBTTHMSNS_D2_R_P0.75––
TP_CAM_JTAG_TCK0.75––
TP_CAM_JTAG_TDI0.75––
TP_CAM_JTAG_TDO0.75––
TP_CAM_JTAG_TMS0.75––
TP_CAM_JTAG_TRST_L0.75––
TP_CAM_LV_JTAG_TCK0.76––
TP_CAM_LV_JTAG_TDI0.75––
TP_CAM_LV_JTAG_TDO0.75––
TP_CAM_LV_JTAG_TMS0.75––
TP_CAM_LV_JTAG_TRSTN0.75––
TP_CAM_PLL_BYPASS0.76––
TP_CAM_TEST_MODE00.75––
TP_CAM_TEST_MODE10.75––
TP_CAM_TEST_MODE20.76––
TP_CAM_UARTRTS0.76––
TP_CAM_UARTTXD0.76––
TP_CPU_MEM_RESET_L0.60––
TP_EDP_DISP_UTIL0.40––
TP_ITPXDP_CLK100MN0.29––
TP_ITPXDP_CLK100MP0.28––
TP_LPC_CLK24M_LPCPLUS_R0.41––
TP_LPDDR3_RSVD10.23––
TP_LPDDR3_RSVD20.23––
TP_LPDDR3_RSVD30.23––
TP_LPDDR3_RSVD40.23––
TP_MCP_RSVD_A510.34––
TP_MCP_RSVD_AU630.34––
TP_MCP_RSVD_AV630.34––
TP_MCP_RSVD_B510.34––
TP_MCP_RSVD_C620.34––
TP_MCP_RSVD_C630.34––
TP_MEM_VDD_SEL_1V5_L0.50––
TP_PCH_I2S1_SCLK0.38––
TP_PCH_I2S1_SFRM0.39––
TP_PCH_I2S1_TXD0.38––
TP_PCH_SLP_LAN_L0.61––
TP_PCH_SLP_WLAN_L0.62––
TP_PM_SLP_A_L0.62––
TP_PPVCCIO_S0_CPU0.08––
TP_SMC_5VSW_PWR_EN0.74––
TP_SPI_CS1_L0.48––
TP_SPI_CS2_L0.48––
TP_SSD_DEVSLPOL––
TP_SUS_PGOOD_MR_L0.69203.300–
TP_TBT_MONDC00.36––
TP_TBT_MONDC10.36––
TP_TBT_PCIE_RESET0_L0.56––
TP_TBT_XTAL25OUT0.27––
TP_USB_5N0.42––
TP_USB_5P0.42––
TPAD_SPI_CLK0.49––
TPAD_SPI_CLK_R0.430.510 TP+and+KB+Installed––
TPAD_SPI_CS_CONN_L0.826––
TPAD_SPI_CS_L0.51––
TPAD_SPI_CS_R_L0.700.640 TP+and+KB+Installed3.300–
TPAD_SPI_IF_EN0.48––
TPAD_SPI_IF_EN_CONN0.66640.630 TP+and+KB+Installed––
TPAD_SPI_INT_GPIO28_L0.458––
TPAD_SPI_INT_GPIO46_L0.45––
TPAD_SPI_INT_L0.45––
TPAD_SPI_INT_S4_WAKE_L_CONN0.410.410 TP+and+KB+Installed3.300–
TPAD_SPI_MISO0.49––
TPAD_SPI_MISO_R0.53640.500 TP+and+KB+Installed––
TPAD_SPI_MOSI0.50––
TPAD_SPI_MOSI_R0.520.510 TP+and+KB+Installed––
TPAD_USB_IF_EN0.59––
TPAD_USB_IF_EN_CONN0.67680.660 TP+and+KB+Installed3.300–
TPAD_WAKE_L0.0050.000 TP+and+KB+Installed––
UNCONNECTED_1030.45––
UNCONNECTED_1370.75––
UNCONNECTED_236OL––
UNCONNECTED_237OL––
UNCONNECTED_244OL––
USB_BT_CONN_N0.77––
USB_BT_CONN_P0.77––
USB_BT_N0.468––
USB_BT_P0.470––
USB_EXTA_N0.452––
USB_EXTA_P0.451––
USB_EXTB_N0.44––
USB_EXTB_P0.44––
USB_ILIM0.54––
USB_ILIM_ROL––
USB_PWR_EN0.523.300–
USB_SD_DM0.71––
USB_SD_DP0.71––
USB_TPAD_N0.43550.420 TP+and+KB+Installed––
USB_TPAD_P0.43490.420 TP+and+KB+Installed––
USB2_EXTA_MUXED_F_N0.647––
USB2_EXTA_MUXED_F_P0.660––
USB2_EXTA_MUXED_N0.644––
USB2_EXTA_MUXED_P0.656––
USB3_EXTA_R2D_C_N0.378––
USB3_EXTA_R2D_C_P0.377––
USB3_EXTA_R2D_NOL––
USB3_EXTA_R2D_POL––
USB3_EXTB_D2R_N0.37––
USB3_EXTB_D2R_P0.37––
USB3_EXTB_D2R_RC_N0.46––
USB3_EXTB_D2R_RC_P0.36––
USB3_EXTB_R2D_NOL––
USB3_EXTB_R2D_POL––
USB3_SD_D2R_N0.36––
USB3_SD_D2R_P0.36––
USB3_SD_R2D_C_N0.36––
USB3_SD_R2D_C_P0.36––
USB3_SD_R2D_P0.34––
VMON_3V3_DIVOL––
VMON_5V_DIVOL––
VMON_Q2_BASEOL––
VREFMRGN_CA_A_ENOL––
VREFMRGN_CA_A_EN_RCOL––
VREFMRGN_CA_A_RDIVOL––
VREFMRGN_CA_ABOL––
VREFMRGN_CA_B_ENOL––
VREFMRGN_CA_B_EN_RCOL––
VREFMRGN_CA_B_RDIVOL––
VREFMRGN_CPU_ENOL––
VREFMRGN_DQ_AOL––
VREFMRGN_DQ_A_ENOL––
VREFMRGN_DQ_A_EN_RCOL––
VREFMRGN_DQ_A_RDIVOL––
VREFMRGN_DQ_BOL––
VREFMRGN_DQ_B_ENOL––
VREFMRGN_DQ_B_EN_RCOL––
VREFMRGN_DQ_B_RDIVOL––
VREFMRGN_MEMVREGOL––
VREFMRGN_MEMVREG_BUFOL––
VREFMRGN_MEMVREG_ENOL––
VREFMRGN_SPARE_BUFOL––
VREFMRGN_SPARE_ENOL––
WIFI_EVENT_L0.730.700–
WOL_EN0.60––
XDP_BPM_L<0>0.3250––
XDP_BPM_L<1>0.3279––
XDP_BPM_L<2>0.28––
XDP_BPM_L<3>0.29––
XDP_BPM_L<4>0.28––
XDP_BPM_L<5>0.29––
XDP_BPM_L<6>0.29––
XDP_BPM_L<7>0.29––
XDP_CPU_PRDY_L0.2907––
XDP_CPU_PREQ_L0.2932––
XDP_CPU_PWRBTN_L0.735––
XDP_CPU_TCK0.0438––
XDP_CPU_TDI0.28––
XDP_CPU_TDO0.19––
XDP_CPU_TMS0.28––
XDP_CPU_VCCST_PWRGD–1.200–
XDP_CPUPCH_TRST_L0.28––
XDP_DBRESET_L0.5965––
XDP_FW_PME_L0.48––
XDP_JTAG_CPU_ISOL_L0.55––
XDP_JTAG_ISP_TCK0.46––
XDP_JTAG_ISP_TDI0.46––
XDP_LPCPLUS_GPIO0.48––
XDP_MLB_RAMCFG00.48––
XDP_MLB_RAMCFG10.484––
XDP_MLB_RAMCFG20.482––
XDP_MLB_RAMCFG30.48––
XDP_PCH_GPIO170.47––
XDP_PCH_GPIO350.48––
XDP_PCH_GPIO760.48––
XDP_PCH_TCK0.3274––
XDP_PCH_TDI0.2925––
XDP_PCH_TDO0.2899––
XDP_PCH_TMS0.2896––
XDP_PCH_UART_SSD_L_BT_H0.48––
XDP_SDCONN_STATE_CHANGE_L0.495––
XDP_SSD_PCIE0_SEL_L0.43––
XDP_SYS_PWROK0.7301––
XDP_TRST_L0.8228––
XDP_USB_EXTA_OC_L0.49––
XDP_USB_EXTB_OC_L0.50––
XDP_USB_EXTC_OC_L0.49––
XDP_USB_EXTD_OC_L0.500––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00165?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00165: diode 0.128, voltage 8.600. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-00165?

OpenBoardData's known-good values for PP3V42_G3H on the 820-00165: diode 0.320, voltage 3.4, resistance to ground 0.300R. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00165?

OpenBoardData's known-good values for PP5V_S5 on the 820-00165: diode 0.43, voltage 5. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00165 board?

Open your own 820-00165 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License