Apple laptop board · OpenBoardData

820-00244 known-good readings

Known-good readings for the Apple laptop board 820-00244: 661 nets, including 78 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 77 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00244.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 78 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 12

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V3_G3H0.35––
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is a 3.3 V always-on rail; the G3H suffix, from the name, marks it as a startup-stage supply that should be present whenever power is connected. The only known-good figure here is a diode reading of 0.35 to ground, with no condition recorded; there is no known-good voltage or resistance value in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.35 suggests a short or leaky load on the rail, while a correct diode reading with missing voltage points upstream at the rail's source. These readings are community guides and vary with board state, so treat a small difference as normal and confirm before replacing anything.

PP3V3_G3H_KBD_F0.354––
AI: what PP3V3_G3H_KBD_F is and how to check it

PP3V3_G3H_KBD_F (820-00244) — reference note

  • From its name, this is a 3.3 V always-on rail (G3H) feeding the keyboard section (KBD). The board data doesn't list which parts sit on it.
  • Known-good reading: diode mode to ground 0.354, from the community archive and a guide only, not a factory spec. No known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail; expect about 3.3 V, but that's general and not a recorded value for this board.
  • A diode reading far from 0.354 usually points to a short or a leaky part on the rail; a missing or low voltage with a normal diode reading points more to the supply side. Confirm with a second measurement before replacing anything.
PP5V_G3H0.453––
AI: what PP5V_G3H is and how to check it

PP5V_G3H is the always-on 5V rail, judging from the G3H suffix in its name. The archive lists one known-good diode reading for it: 0.453, with no condition recorded. Check it with the board unpowered in diode mode from PP5V_G3H to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.453 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

PPBUS_G3H0.360––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this 820-00244; the G3H suffix, from the name, marks it as an always-on rail. The only known-good reading in the archive is a diode value of 0.360 to ground, with no condition recorded; there is no known-good voltage here. Check it with the board unpowered in diode mode to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.360 usually points to a short or a leaky component on the bus, but one reading alone doesn't confirm a bad part, so compare with a matching net or a known-good board before replacing anything.

PPBUS_G3H_TPAD_FLT0.360––
AI: what PPBUS_G3H_TPAD_FLT is and how to check it

PPBUS_G3H_TPAD_FLT is the trackpad branch of the main PPBUS rail; the G3H part of the name indicates it is always on, and FLT suggests a filtered feed to the trackpad. The archive lists one known-good diode reading of 0.360 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the net to ground, then power the board and measure the voltage on the same point. A diode reading far from 0.360 usually points to a short or a damaged component on that branch, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything.

PPDCIN_G3H0.560––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the DC-in rail that feeds the board from the charger; the G3H suffix, from the name, marks it as an always-on startup rail. The archive lists a diode reading of 0.560 to ground for this net, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then measure its voltage with the charger connected. A diode reading far from 0.560 usually points to a short or a damaged component on that rail rather than the rail itself. This is a community guide reading, not a confirmed spec, so compare against a matching net or a known-good board before replacing anything.

PPDCIN_G3H_CHGR0.560––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in its name indicates it is always-on when power is present. The archive lists one known-good diode reading of 0.560 to ground, with no condition noted and no known-good voltage reading here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.560; then apply power and check the DC voltage present. A diode reading far below 0.560 usually points to a short or leaky part on the rail, while a much higher or open reading suggests a broken connection. These are community readings and only a guide, so confirm on a known-good board before replacing anything.

PPVBAT_G3H_CHGR_R0.360––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; from its name, G3H means it is always on, and CHGR ties it to the charger circuit. The archive lists a diode reading of 0.360 to ground for this rail, with no condition noted, so treat it as a guide. Check it with the board unpowered and the battery disconnected: diode mode, red probe on ground, black on the rail. Then apply power and measure the voltage on the rail. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.360 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PPVBAT_G3H_CHGR_REG0.360––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From its name, PPVBAT_G3H_CHGR_REG is a battery-derived, always-on (G3H) rail tied to the charger circuit. The data doesn't identify which parts sit on it.
  • Known-good: Diode reading to ground is 0.360. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: A much lower diode reading usually points to a short or leaky part on the rail. Readings are community guides and vary with board state, so confirm before replacing anything.
PPVBAT_G3H_CONN0.689––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judging from its name (PP = power rail, VBAT = battery, G3H = always on). The archive lists one known-good diode reading, 0.689, with no condition attached, and no known-good voltage reading.

  • Check it with the board unpowered and the battery disconnected: diode mode, black probe to ground, red probe on the net. Compare with 0.689.
  • Then apply power and measure the voltage on the net; no known-good voltage here, so compare against a matching battery-side net or a known-good board.
  • A diode reading far below 0.689 usually points to a short or a leaky part on the rail; far above can mean an open path. One reading isn't proof, so confirm before replacing anything.
PPVIN_G3H_P3V3G3H0.537––
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H is an always-on G3H rail, judging from its name; the PPVIN part suggests it is the input feed behind the P3V3G3H 3.3 V always-on supply. The only known-good reading here is a diode value of 0.537 to ground, with no condition noted; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.537.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded here, so compare against a matching rail on a known-good board.
  • A diode reading far below 0.537 usually points to a short or a failing load on the rail; a much higher or open reading points to a broken feed or return path.
  • Readings vary with board state, so treat 0.537 as a guide, not a pass/fail limit.
PPVRTC_G3H0.440––
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on RTC rail; the G3H suffix comes from the name and means it should be present whenever the board has power. The only known-good reading here is a diode value of 0.440 to ground, with no condition listed; no known-good voltage is recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.440 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

S5 and SUS: standby 17

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_S5_PCH_DCPDSW0.360––
AI: what PP1V_S5_PCH_DCPDSW is and how to check it

PP1V_S5_PCH_DCPDSW is a 1 V standby rail feeding the PCH's display-port switch, judging by the name (S5/SUS = standby stage). The archive lists one known-good diode reading of 0.360 to ground; there is no known-good voltage reading here.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far below 0.360 suggests a short or leaky load on the rail; far above it can mean an open path or a missing part.
  • With power applied, a rail that should sit near 1 V but stays at zero points to the standby supply or its enable, not the load.

These readings are community guides and vary with board state, so treat a small difference as normal and confirm on a matching net before replacing anything.

PP1V_SUS0.235–104.600R
AI: what PP1V_SUS is and how to check it

PP1V_SUS is a standby rail: the "SUS" in its name indicates it stays present in suspend/standby, and the "1V" indicates a nominal 1 V rail (this is from the name, not the board data). Known-good readings here are diode 0.235 and resistance 104.600R; no known-good voltage reading is recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.235 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare against the other standby rails before replacing anything.

PP1V_SUS_PCH_VCCCLK40.226––
AI: what PP1V_SUS_PCH_VCCCLK4 is and how to check it

PP1V_SUS_PCH_VCCCLK4 is a 1 V standby rail feeding the PCH clock area; the "SUS" and "S5" parts of the name indicate it belongs to the standby stage, not the main power-on rails.

  • Known-good: diode-to-ground 0.226 (archive reading, guide only). No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.226 usually points to a short or a damaged component on that net, but one reading isn't proof — compare with a matching rail or a known-good board before replacing anything.
PP1V_SUS_PCH_VCCCLK50.226––
AI: what PP1V_SUS_PCH_VCCCLK5 is and how to check it
  • What it is: From its name, PP1V_SUS_PCH_VCCCLK5 is a 1 V standby rail feeding the PCH clock section; the S5/SUS part of the name puts it in the standby stage.
  • Known-good reading: diode 0.226 (community value, guide only; no condition recorded). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open path. Confirm with voltage before replacing anything.
PP1V_SUSRS0SW_PCHCLK0.225––
AI: what PP1V_SUSRS0SW_PCHCLK is and how to check it

PP1V_SUSRS0SW_PCHCLK — 820-00244

  • What it is: From the name, a 1 V standby rail (SUS/S5) feeding a switched PCH clock supply. The name is the only description available; the parts on this net aren't listed.
  • Known-good reading: Diode to ground 0.225, no condition recorded. No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.225. Then power up and measure the voltage — expect about 1 V from the name, but that's general, not a recorded value.
  • If it's far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path or missing supply. Confirm with a second measurement before replacing anything.
PP1V_SUSSW_HSIO0.226––
AI: what PP1V_SUSSW_HSIO is and how to check it

PP1V_SUSSW_HSIO is a 1 V standby switch rail for the HSIO (high-speed I/O) section, going by its name; the archive lists it at the S5/SUS standby stage. The only known-good reading here is a diode value of 0.226 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.226 usually points to a short or a leaky part on that rail, but a small difference can be normal, so confirm with a voltage measurement before replacing anything.

PP1V_SUSSW_PCH_VCCAMPHYPLL0.226––
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL is and how to check it

PP1V_SUSSW_PCH_VCCAMPHYPLL — reference note

  • From its name, this is a 1 V standby (SUS/S5) switched rail feeding the PCH's VCCAMPHYPLL supply. The name is the only description available; the parts on the net aren't documented.
  • Known-good: diode 0.226 in diode mode. No known-good voltage or resistance reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.226. Then power up and measure the voltage, which should be near 1 V once the rail is enabled.
  • A diode reading far below 0.226 suggests a short or a leaky load on the rail; far above it suggests an open path. One reading alone doesn't condemn a part, so confirm with the voltage and a second measurement.
PP1V2_S5_SMC_VDDC0.515––
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: From the name, PP1V2_S5_SMC_VDDC is a 1.2 V rail for the SMC (system management controller) that comes up in the S5/SUS standby stage. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0.515 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a bad part on the rail; a missing or wrong voltage points to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP1V2_S5SW0.360––
AI: what PP1V2_S5SW is and how to check it

PP1V2_S5SW — reference note

  • What it is: From the name, a 1.2 V rail in the S5/SUS standby domain, so it's expected to be up in standby before the main rails. The parts it feeds aren't known for this board.
  • Known-good reading: diode 0.360 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher one suggests an open feed or a missing part. A wrong voltage with a normal diode reading points more to the supply side than the load.
PP1V8_SUS0.420––
AI: what PP1V8_SUS is and how to check it
  • PP1V8_SUS is a 1.8 V standby rail; the "SUS" in the name indicates it stays alive in standby (from the name, not from board data).
  • Known-good: diode to ground 0.420 (archive value, a guide only; board state varies). No known-good voltage reading is recorded here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.420 suggests a short or open on that net; a correct diode reading with wrong voltage points upstream at the standby supply or its enable.
PP3V0_S5_AVREF_SMC0.592––
AI: what PP3V0_S5_AVREF_SMC is and how to check it

PP3V0_S5_AVREF_SMC (820-00244) — reference note

  • From its name, this is a 3.0 V standby (S5) reference rail feeding the SMC's analog reference input; it is a low-current reference, not a main power rail.
  • Known-good reading in the archive: diode mode to ground 0.592, no condition recorded. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage at the rail; expect close to 3.0 V from the name, but that figure is general, not from this board's data.
  • A diode reading far below 0.592 usually points to a short or a leaky load on the rail; far above it suggests an open trace or missing connection. Confirm with a voltage measurement before suspecting any part.
PP3V3_S50.358––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the "S5" suffix, from its name, places it in the always-on/standby stage that should be present before the board fully powers up. The archive lists a diode reading of 0.358 for this net, with no condition noted, so treat it as a guide only. To check it, power off and measure diode mode from PP3V3_S5 to ground, then apply power and measure the voltage. A diode reading far below 0.358 usually points to a short or a leaky load on the rail, while a missing or low voltage with a normal diode reading points more toward the supply that generates it. No known-good voltage reading is recorded here, so compare against a known-good board of the same model.

PP3V3_S5_SMC_VDDA0.360––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply; the S5 and SUS parts of the name indicate it comes up in the standby stage. The only known-good figure here is a diode reading of 0.360 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.360 usually points to a short or a leaky part on the rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_SUS0.360––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail, from its name: "SUS" means it stays up in standby, and "S5" marks the standby stage of the power sequence. The archive lists one known-good reading: diode 0.360 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.360 usually points to a short or a leaky part on the rail; far above it suggests an open path. No known-good voltage is recorded here, so compare against a matching standby rail or a known-good board.

PP5V_S50.441––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail: the "S5" and "SUS" in the name mark it as a standby supply that should be present before the board fully powers on (from the name, not from board data). The archive lists one known-good reading, diode 0.441 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from PP5V_S5 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.441 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PPBUS_S5_HS_COMPUTING_ISNS0.360––
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it

PPBUS_S5_HS_COMPUTING_ISNS — reference note

  • What it is: from the name, a PPBUS rail (the main battery/charger bus) feeding the S5 standby domain, with "HS_COMPUTING" suggesting a high-side computing supply and "ISNS" a current-sense line. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.360 to ground, from the readings archive (community contribution, so a guide only). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the net to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail, and a much higher one to an open trace or missing part. Confirm with a second measurement before replacing anything.
PPVCORE_SUS_PCH0.250–66.700R
AI: what PPVCORE_SUS_PCH is and how to check it

PPVCORE_SUS_PCH is a standby (SUS/S5) core rail for the PCH, judged from the rail name. The archive lists a diode reading of 0.250 and a resistance of 66.700R; treat these as a guide, since they come from community contributions and vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A reading far from 0.250 or 66.700R usually points to a short or a damaged load on the rail, but a small difference can be normal, so confirm before replacing anything. No known-good voltage reading is recorded here.

S4 7

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V2_S4SW_SSD_HOT0.325––
AI: what PP1V2_S4SW_SSD_HOT is and how to check it

PP1V2_S4SW_SSD_HOT is a 1.2 V rail feeding the SSD section, and the S4 in its name marks it as a later startup stage (both from the name). The only known-good reading here is a diode value of 0.325 to ground; no voltage reading is recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.325, or a voltage well off 1.2 V, usually points to a short or a rail that isn't coming up, but one reading alone doesn't confirm a bad part.

PP1V8_S4SW_SSD_HOT0.371––
AI: what PP1V8_S4SW_SSD_HOT is and how to check it
  • What it is: From the name, PP1V8_S4SW_SSD_HOT is a 1.8 V rail switched on at the S4 startup stage and feeding the SSD section. The "HOT" suffix suggests it stays on in some sleep or hot states, but that's general naming, not board data.
  • Known-good reading: diode 0.371 to ground, from the readings archive. No known-good voltage or resistance is recorded here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.371. Then power up and measure the voltage, expecting about 1.8 V once the board reaches S4.
  • If it's far off: a much lower diode reading points to a short or a leaky part on the rail; a correct diode reading with no voltage points upstream, to the switch or regulator that enables it at S4. Treat the archived value as a guide only, since it varies with board state.
PP3V3_S40.478––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail, and the "S4" in its name places it at the S4 startup stage. The only known-good reading here is a diode value of 0.478 to ground; there is no known-good voltage reading in this data.

  • With the board unpowered, measure diode mode from PP3V3_S4 to ground and compare with 0.478.
  • Then power the board and measure the voltage on the rail; the data gives no expected voltage, so compare against a matching rail or a known-good board.

A diode reading far from 0.478 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S4_TPAD_F0.416––
AI: what PP3V3_S4_TPAD_F is and how to check it

PP3V3_S4_TPAD_F is a 3.3 V rail feeding the trackpad, and the S4 in its name marks it as a startup-stage rail. The only known-good reading here is a diode value of 0.416 to ground; no voltage reading is recorded, so there is no known-good voltage to compare against. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.416 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S40.350––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, both from its name. The only known-good reading here is a diode value of 0.350 to ground; there is no known-good voltage reading for this rail. With the board unpowered, measure diode mode from PP5V_S4 to ground and compare with 0.350, then apply power and check the voltage. A diode reading far from 0.350 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S4_TPAD_F0.164––
AI: what PP5V_S4_TPAD_F is and how to check it

PP5V_S4_TPAD_F is a 5 V rail for the trackpad, and the S4 in its name marks it as a later startup stage. The only known-good reading here is a diode value of 0.164 to ground; no voltage reading is recorded. With the board unpowered, measure diode mode from PP5V_S4_TPAD_F to ground and compare with 0.164, then power up and check the voltage. A diode reading far from 0.164 usually points to a short or a damaged part on that rail, but one reading alone isn't proof.

PP5V_S4RS00.483––
AI: what PP5V_S4RS0 is and how to check it

PP5V_S4RS0 is a 5 V rail in the S4 startup stage, inferred from its name; the archive has no part or net list for this board. Its only known-good reading is a diode value of 0.483, with no condition recorded, and there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.483 usually points to a short or a leaky component on that rail, but one reading isn't proof a part is bad.

S3: memory 7

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V_S30.265––
AI: what PP1V_S3 is and how to check it

PP1V_S3 is a memory-stage rail (S3), as the name suggests. The archive lists one known-good diode reading to ground: 0.265, with no condition noted. With the board unpowered, measure diode mode from PP1V_S3 to ground and compare; then apply power and check the voltage. A reading far from 0.265 usually points to a short or a faulty component on that rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is recorded here.

PP1V2_S30.235––
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail; the S3 suffix in its name indicates it belongs to the memory stage of the startup sequence (from the name, not from a schematic). The archive lists one known-good reading: diode 0.235, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode value far from 0.235 usually points to a short or a leaky load on the rail, but one reading doesn't confirm a bad part.

PP1V8_S30.450––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail, and the S3 suffix in its name marks it as a memory-stage rail that comes up during startup. The only known-good figure here is a diode reading of 0.450 to ground; there is no known-good voltage reading for this rail.

  • With the board unpowered, measure diode mode from PP1V8_S3 to ground and compare with 0.450.
  • Then apply power and check the voltage at the rail; 1.8 V is what the name implies, but that is general, not a recorded value.

A diode reading far below 0.450 usually points to a short or a leaky part on the rail; a reading far above it can mean an open path. Treat these as a guide only, since readings vary with board state, and confirm with a second measurement before replacing anything.

PP5V_S3_CPUVR_VCC0.346––
AI: what PP5V_S3_CPUVR_VCC is and how to check it

PP5V_S3_CPUVR_VCC (820-00244) — a 5 V rail that, from its name, belongs to the S3 (memory/suspend) startup stage and feeds the CPU VR (voltage regulator) supply.

  • Known-good reading: diode 0.346 to ground (community archive value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.346. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed or a missing enable. Confirm with the voltage reading before replacing anything.
PPVREF_S3_MEM_VREFCA0.727––
AI: what PPVREF_S3_MEM_VREFCA is and how to check it

PPVREF_S3_MEM_VREFCA is a memory reference rail in the S3 (suspend-to-RAM) power state, judged from its name; it is not a main supply. The only known-good figure here is a diode reading of 0.727 to ground, with no condition recorded. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. No known-good voltage is listed, so compare against a matching memory reference rail or a known-good board. A diode reading far from 0.727 usually points to a short or a faulty part on that net, but one reading alone doesn't confirm a bad part.

PPVREF_S3_MEM_VREFDQ_A0.762––
AI: what PPVREF_S3_MEM_VREFDQ_A is and how to check it

PPVREF_S3_MEM_VREFDQ_A is a memory reference-voltage rail; the S3 and MEM/VREFDQ parts of the name indicate it belongs to the S3 (memory) power state and is a DDR reference voltage. The only known-good reading in the archive is a diode value of 0.762, with no condition recorded and no known-good voltage. To check it, power the board off and measure diode mode from the net to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.762 usually points to a short or a damaged component on that net, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PPVREF_S3_MEM_VREFDQ_B0.769––
AI: what PPVREF_S3_MEM_VREFDQ_B is and how to check it

PPVREF_S3_MEM_VREFDQ_B — reference note

  • From its name, this is an S3-state memory reference voltage (VREFDQ) for the memory subsystem; the "B" suffix suggests one of a pair of reference rails.
  • Known-good: diode reading 0.769 to ground (community archive, condition not stated). No known-good voltage reading here.
  • To check: power off, measure diode mode from the rail to ground; then power on and measure the DC voltage at the rail.
  • A diode reading far below 0.769 usually points to a short or a leaky part on the rail; far above suggests an open path. A wrong voltage with a normal diode reading points more toward the supply or its reference divider.

S0: running 35

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V9_S0SW_SSD_CORE0.225––
AI: what PP0V9_S0SW_SSD_CORE is and how to check it
  • What it is: From its name, PP0V9_S0SW_SSD_CORE is a 0.9 V core rail for the SSD, active in the S0 (running) state. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: Diode mode to ground is 0.225 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power on and measure the voltage at the rail; expect about 0.9 V from the name, but that's general, not a recorded value.
  • If far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Compare against a known-good board before replacing anything.
PP0V9_S0SW_SSD_FIXED0.290––
AI: what PP0V9_S0SW_SSD_FIXED is and how to check it

PP0V9_S0SW_SSD_FIXED is a 0.9 V rail feeding the SSD section, from its name; the S0 part means it belongs to the running (S0) state, so it should come up once the board is fully on. The archive lists one known-good diode reading of 0.290 to ground, with no condition noted and no known-good voltage reading here. Check it unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage at the rail. A diode reading far from 0.290 usually points to a short or a leaky part on that rail, while a correct diode reading with no voltage points upstream to its enable or supply. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP1V_S0SW0.002––
AI: what PP1V_S0SW is and how to check it

PP1V_S0SW is a 1 V rail that, from its name, is a switched supply active in the S0 (running) state. The archive lists a diode reading of 0.002 to ground; no voltage or resistance reading is recorded here, so there is no known-good value of those kinds. With the board unpowered, measure diode mode from PP1V_S0SW to ground and compare with 0.002, then power up and check the voltage. A diode reading far below known-good usually points to a short or a failed part on the rail; a far higher one can mean an open path. Treat the archive value as a guide only, since readings vary with board state.

PP1V_S0SW_PCHCLK0.929––
AI: what PP1V_S0SW_PCHCLK is and how to check it

PP1V_S0SW_PCHCLK is a 1 V switched rail for the PCH clock, from its name: the S0 part means it's present in the running state. The only known-good reading here is diode mode 0.929 to ground, with no condition recorded, and there is no known-good voltage reading here. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far from 0.929 usually points to a short or a damaged part on that net, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PP1V2_S0SW0.236––
AI: what PP1V2_S0SW is and how to check it

PP1V2_S0SW is a 1.2 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "SW" usually means it feeds a switched supply. The archive lists one known-good diode reading for this net: 0.236, with no condition noted. Check it with the board unpowered in diode mode from PP1V2_S0SW to ground, then power up and measure the voltage. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.236 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V2_S0SW_SSD_COLD0.273––
AI: what PP1V2_S0SW_SSD_COLD is and how to check it

PP1V2_S0SW_SSD_COLD is a 1.2 V rail feeding the SSD, and the S0 in its name indicates it's present in the running state. The archive lists one known-good reading: diode 0.273, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.273 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP1V5_S00.423––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" suffix, from its name, marks it as a running-state supply rather than a standby rail. The only known-good figure here is a diode reading of 0.423 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.423 usually points to a short or a failed part on the rail, while a much higher or open reading suggests a broken connection or missing part. This is a guide only, and the actual voltage expected isn't in the data.

PP1V8_S0SW_SSD_COLD0.290––
PP3V3_S00.360––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, judging from its name. The only known-good figure here is a diode reading of 0.360 to ground; there's no known-good voltage or resistance for this rail.

  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Compare with 0.360.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a matching 3.3 V rail or a known-good board.
  • A diode reading far from 0.360 usually points to a short or a leaky part on the rail, but one reading isn't proof.
PP3V3_S0_CPUTHMSNS_R0.4040.011 LIKE ON BRD PROBLEM––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding the CPU thermal sensor circuit; it is a sense rail, not a main power rail.
  • Known-good readings: diode 0.404 to ground. A second archived reading is 0.011, noted as a problem board, so treat 0.404 as the guide and 0.011 as a short-like fault.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the DC voltage, expecting about 3.3 V.
  • What a far-off reading means: a diode near 0.011 suggests a short or a failed part on that net, while a high or open reading suggests a broken trace or missing feed. No known-good voltage value is recorded here, so compare against a matching rail or a known-good board.
PP3V3_S0SW_LCD0.612––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD (820-00244) — a 3.3 V LCD-switched rail; the name suggests an S0 (running) state, switched supply for the display section.

  • Known-good: diode 0.612 to ground. No known-good voltage reading here.
  • Check unpowered in diode mode, red probe to ground, black to the rail; then power up and measure the voltage.
  • A diode reading far from 0.612 usually points to a short or leaky part on that rail; a missing voltage points upstream to the switch or enable.
PP5V_S00.466––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the main 5 V rail that is present in the S0 (running) state, judging from the name. The only known-good reading here is a diode value of 0.466 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from PP5V_S0 to ground, then power up and measure the voltage. A diode reading far below 0.466 usually points to a short or a leaky load on the rail, while a missing voltage with a normal diode reading points more toward the supply that creates it. These readings are community guides and vary with board state, so confirm against a matching rail or a known-good board before replacing anything.

PP5V_S0_ALSCAM_F0.466––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V rail, and the S0 in its name indicates it belongs to the running state. The only known-good reading here is a diode value of 0.466; no voltage reading is recorded.

  • With the board unpowered, measure diode mode from PP5V_S0_ALSCAM_F to ground and compare with 0.466.
  • Then power the board and check the voltage on the rail while it is in S0.

A diode reading far from 0.466 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault. No known-good voltage is available for this rail.

PP5V_S0_CPUCORE10.483––
AI: what PP5V_S0_CPUCORE1 is and how to check it

PP5V_S0_CPUCORE1 is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds CPU core circuitry. The only known-good reading here is a diode value of 0.483 to ground; there is no known-good voltage reading in this data.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.483.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a matching rail or a known-good board.
  • A diode reading far below 0.483 usually points to a short or a failing load on the rail; a much higher one can mean an open path. Confirm with a second measurement before replacing anything.
PP5V_S0_CPUCORE20.483––
AI: what PP5V_S0_CPUCORE2 is and how to check it

PP5V_S0_CPUCORE2 — the name indicates a 5 V rail (PP5V), active in the S0 running state, feeding CPU core 2. This is from the name only; the parts on the net aren't documented here.

  • Known-good reading: diode 0.483 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check it: power off, measure diode mode from the rail to ground; then power on and measure the DC voltage at the rail.
  • Far from known-good: a much lower diode reading usually points to a short or a leaky load on the rail; a much higher one to an open path. A small difference can be normal, so confirm with a second measurement before replacing anything.
PP5V_S0_CPUGT10.484––
AI: what PP5V_S0_CPUGT1 is and how to check it

PP5V_S0_CPUGT1 is a 5 V rail, from its name: the S0 part means it belongs to the running state, and CPUGT1 suggests it feeds CPU-related circuitry (general naming, not confirmed for this board). The only known-good reading here is a diode value of 0.484 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered: diode mode from the rail to ground, red probe on ground, and compare with 0.484.
  • Then power the board and measure the DC voltage on the rail; without a known-good voltage, compare against a matching rail on a known-good board.
  • A diode reading far below 0.484 usually points to a short or a leaky part on the rail; a much higher reading can mean an open connection. One reading alone doesn't confirm a bad part, so check both before replacing anything.
PP5V_S0_CPUGT20.483––
AI: what PP5V_S0_CPUGT2 is and how to check it

PP5V_S0_CPUGT2 is a 5 V rail; the S0 in the name indicates it belongs to the running (S0) state, and CPUGT2 suggests a CPU-related branch. The only known-good reading in the archive is a diode value of 0.483 to ground, with no condition recorded and no known-good voltage reading. Check it with the board unpowered in diode mode from the net to ground, then power up and measure the voltage on the net. A diode reading far from 0.483 usually points to a short or a damaged component on that rail, but confirm with a voltage measurement before replacing anything.

PP5V_S0_KBD_F0.466––
AI: what PP5V_S0_KBD_F is and how to check it

PP5V_S0_KBD_F — 820-00244

  • What it is: a 5 V keyboard-related rail that is on in S0 (running), judged from the name; the board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.466 (community value, a guide only; condition not recorded). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from PP5V_S0_KBD_F to ground; then power up into S0 and measure the voltage, expecting about 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; no voltage in S0 points upstream to the rail's enable or source supply. Confirm with a second measurement before replacing anything.
PP5V_S0SW_LCD0.577––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is the switched 5 V LCD rail, from its name: a 5 V supply that is switched on in the S0 (running) state to feed the display. The only known-good reading here is a diode value of 0.577 to ground; no voltage or resistance reading is recorded for this rail.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage in the S0 state.
  • A diode reading far below 0.577 usually points to a short or a leaky load on the rail; a much higher reading can mean an open path.
  • No known-good voltage is recorded here, so compare against a matching rail on a known-good board rather than treating one reading as proof of a bad part.
PPBUS_S0_LCDBKLT_FUSED0.360––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it

PPBUS_S0_LCDBKLT_FUSED is the fused backlight boost rail for the LCD, going by its name: PPBUS is the main adapter/battery bus, LCDBKLT is display backlight, and the S0 suffix means it's present in the running state. The archive lists one known-good diode reading of 0.360 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.360 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PPBUS_S0_LCDBKLT_PWR_SW0.440––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
  • What it is: From its name, PPBUS_S0_LCDBKLT_PWR_SW is the switched backlight power rail for the LCD, active in the S0 (running) state. It's the switched side feeding the backlight boost circuit.
  • Known-good reading: Diode mode to ground is 0.440 in the archive. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • What a far-off reading suggests: A diode value well below 0.440 points to a short or leaky part on the rail; a much higher or open reading points to a broken connection. Confirm with a second measurement before replacing anything.
PPVCCG0_S0_CPU0.020––
AI: what PPVCCG0_S0_CPU is and how to check it

PPVCCG0_S0_CPU is a CPU power rail; the "S0" in its name indicates the running state, and "VCCG0" suggests a CPU core supply (general naming, not from board data). The only known-good reading here is a diode value of 0.020 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.020 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVCCG1_S0_CPU0.021––
AI: what PPVCCG1_S0_CPU is and how to check it

PPVCCG1_S0_CPU — reference note

  • What it is: From the name, a CPU power rail (VCC, CPU domain) that is active in the S0 running state. The exact parts on it aren't documented here.
  • Known-good reading: Diode mode to ground, board unpowered: 0.021. This is a community guide value and varies with board state. No known-good voltage reading here.
  • How to check: Power off and discharge, then measure diode mode from the rail to ground. Then apply power and measure the rail voltage in the running state.
  • If far off: A much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path or missing supply. Confirm with a second reading before replacing anything.
PPVCCGT_S0_CPU_PH10.013–13.200R
AI: what PPVCCGT_S0_CPU_PH1 is and how to check it

PPVCCGT_S0_CPU_PH1 is a CPU graphics power rail; the "S0" in the name indicates it is active in the running state, and "PH1" suggests a phase of a multiphase supply (from the name). The archive lists a diode reading of 0.013 and a resistance of 13.200R for this net, with no condition noted, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on the rail with power applied during S0. A reading far from 0.013 or 13.200R usually points to a short or a faulty phase component on that rail, but one reading alone doesn't confirm a bad part; no known-good voltage reading is recorded here.

PPVCCGT_S0_CPU_PH20.013–13.200R
AI: what PPVCCGT_S0_CPU_PH2 is and how to check it

PPVCCGT_S0_CPU_PH2 is a CPU graphics power rail; the "S0" in the name indicates it is active in the running state, and "PH2" suggests a phase of a multiphase supply (from the name only). The archive lists a diode reading of 0.013 and a resistance of 13.200R for this net, with no condition noted, so treat them as a guide. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage on it with power applied and the board running. A reading far from 0.013 or 13.200R usually points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is available here, so compare against a matching rail or a known-good board.

PPVCCIO_S00.180––
AI: what PPVCCIO_S0 is and how to check it

PPVCCIO_S0 is an S0 (running-state) power rail, judging from its name, likely an I/O supply; the exact parts it feeds aren't documented here. The only known-good reading in the data is a diode value of 0.180 to ground. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure its voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.180 usually points to a shorted load or capacitor on the rail; confirm with voltage and resistance before replacing anything.

PPVCCSA_DDR_S00.047––
AI: what PPVCCSA_DDR_S0 is and how to check it

PPVCCSA_DDR_S0 is a running-state (S0, from the name) supply rail, likely feeding the DDR memory subsystem; the exact parts on it aren't known here. The only known-good reading in the archive is a diode value of 0.047 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure its voltage with power applied. A diode reading far from 0.047 usually points to a short or a leaky part on that rail, but one reading isn't proof — compare against a matching rail or a known-good board before replacing anything. No known-good voltage reading is recorded here.

PPVCCSA_S00.040––
AI: what PPVCCSA_S0 is and how to check it

PPVCCSA_S0 is a power rail; the S0 suffix in its name indicates it is up in the running state. The archive lists one known-good reading: diode 0.040 to ground, with no condition noted, and no voltage or resistance value is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on it. A diode reading far from 0.040 usually points to a short or a leaky load on the rail rather than the rail itself, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVCCSA_S0_CPU0.040–26.400R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is a CPU power rail; the S0 in its name indicates it is active in the running state. The archive lists a diode reading of 0.040 and a resistance of 26.400R, with no condition recorded, so treat these as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on the rail with power applied. A diode value far below 0.040 usually points to a short or a leaky component on the rail, while a much higher value can mean an open connection. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PPVCORE_S0_CPU0.019––
AI: what PPVCORE_S0_CPU is and how to check it

PPVCORE_S0_CPU is the CPU core power rail; the S0 in the name indicates it is active in the running state. The only known-good reading here is a diode value of 0.019 to ground, with no condition recorded, and there is no known-good voltage reading in this data.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.019.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a known-good board or the rail's expected level from the schematic.
  • A diode reading far from 0.019 usually points to a short or a leaky component on the rail, but a small difference can be normal, so confirm with a second measurement before replacing anything.
PPVCORE_S0_CPU_PH10.019–15.600R
AI: what PPVCORE_S0_CPU_PH1 is and how to check it
  • What it is: From the name, PPVCORE_S0_CPU_PH1 is a CPU core power rail (VCORE) in the S0 running state; PH1 likely marks one phase of a multi-phase core supply. This is from the name only, not from board data.
  • Known-good readings: diode 0.019 and resistance 15.600R, with no condition stated. These come from community contributions and are a guide, not a guarantee.
  • How to check: With the board powered off, measure diode mode to ground on the rail, then measure resistance to ground. Then power the board and measure the rail voltage; no known-good voltage is recorded here.
  • What a far-off reading suggests: A much lower diode or resistance reading points to a short or a failing load on the core rail; a much higher one can mean an open path. Confirm with a second measurement before suspecting any part.
PPVCORE_S0_CPU_PH20.019–15.600R
AI: what PPVCORE_S0_CPU_PH2 is and how to check it

PPVCORE_S0_CPU_PH2 — reference note

  • What it is: From the name, this is a CPU core power rail (VCORE) in the S0 (running) state, phase 2 (PH2) of a multiphase supply. It's a high-current rail, so expect very low readings to ground.
  • Known-good readings (community guide): diode 0.019, resistance 15.600R. No known-good voltage reading here.
  • How to check: With the board unpowered, diode mode from the rail to ground; then power up and measure the rail voltage. Compare against the other VCORE phases and a known-good board.
  • If far off: A much higher diode/resistance reading suggests an open phase or feed; a near-zero reading suggests a short. A single reading doesn't confirm a bad part — check the other phases first.
PPVCORE_S0_GT0.013––
AI: what PPVCORE_S0_GT is and how to check it

PPVCORE_S0_GT is a GPU core power rail; the S0 in the name indicates it is active in the running state. The only known-good reading here is a diode value of 0.013 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then measure the voltage with power applied and the board running. A diode reading far above 0.013 usually points to an open or missing connection on the rail, while a value well below it suggests a short to ground; a single reading is only a guide, so compare against a matching rail or a known-good board before condemning anything.

PPVIN_S0_CPUVR_VIN0.369––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VR (voltage regulator) input rail, active in the S0 running state, as its name suggests. The archive lists one known-good diode reading of 0.369 to ground, with no condition noted and no known-good voltage reading here.

  • Check it unpowered in diode mode from the rail to ground; a reading near 0.369 is the guide.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded here, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far below 0.369 usually points to a short or a leaky part on the rail; far above can mean an open path. One reading alone doesn't confirm a bad part.
PPVOUT_S0_LCDBKLT0.635––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight boost output rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "LCDBKLT" points to LCD backlight. The archive lists a diode-mode reading of 0.635 to ground for this rail, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage there. No known-good voltage reading is recorded here, so compare against a matching backlight rail on a known-good board. A diode reading far from 0.635 usually points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part.

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD0.465––
ANI01_VREF0.409––
ANI23_VREF0.409––
AP_CLKREQ_L0.489––
AP_DEV_WAKE0.554––
AP_PCIE_WAKE_L0.510––
AP_RESET_L0.555––
AP_S0IX_WAKE_L0.646––
AP_S0IX_WAKE_SEL0.665––
AUD_LRCLK_A0.524––
AUD_LRCLK_LEFT10.530––
AUD_LRCLK_LEFT20.530––
AUD_PWR_EN0.770––
AUD_SCLK_A0.562––
AUD_SCLKA_LEFT10.571––
AUD_SCLKA_LEFT20.571––
AUD_SDOUT_A0.525––
AUD_SDOUT_LEFT10.530––
AUD_SDOUT_LEFT20.530––
AUD_SPKRAMP_MODE0.530––
AUD_SPKRAMP_MODE_LEFT10.541––
AUD_SPKRAMP_MODE_LEFT20.541––
BKL_FB0.365––
BKLT_EN_R0.548––
BKLT_SCL_R0.542––
BKLT_SD0.596––
BKLT_SDA_R0.542––
BKLT_SENSE_OUT0.731––
BT_SPI_CLK0.591––
BT_SPI_CS_L0.681––
BT_SPI_MISO0.706––
BT_SPI_MOSI0.697––
BT_UART_RTS_L0.431––
BTROM_HOLD_L0.725––
BTROM_WP_L0.715––
CAM_TEST_MODE0.768––
CAMERA_PWR_EN0.584––
CAMERA_RESET_L0.526––
CHGR_ACIN0.62––
CHGR_AMON0.627––
CHGR_BGATE0.66––
CHGR_BMON0.628––
CHGR_BOOST_DH0.716––
CHGR_BOOST_DL0.464––
CHGR_BOOST_SW0.45––
CHGR_BOOT10.58––
CHGR_BOOT1_RC0.58––
CHGR_BOOT20.59––
CHGR_BOOT2_RC0.59––
CHGR_BUCK_DH0.932––
CHGR_BUCK_DL0.463––
CHGR_COMP0.61––
CHGR_CSI_N0.56–2.500R
CHGR_CSI_P0.56–2.500R
CHGR_CSI_R_N0.560––
CHGR_CSI_R_P0.560––
CHGR_CSO_N0.357–2.300R
CHGR_CSO_P0.357–2.300R
CHGR_CSO_R_N0.360––
CHGR_CSO_R_P0.360––
CHGR_LDO_P3V00.61––
CHGR_LDO_P5V00.42––
CHGR_LDO_VDDA0.43––
CHGR_LDO_VDDP0.43––
CHGR_PHASE0.470––
CHGR_PHASE20.470––
CPU_CATERR_L0.295––
CPU_CFG_RCOMP0.052––
CPU_CFG<4>0.316––
CPU_PECI_R0.315––
CPU_PROCHOT_L0.488––
CPU_VCCGTSENSE_N0.004––
CPU_VCCGTSENSE_P0.014––
CPU_VCCSASENSE_P0.040––
CPU_VCCSENSE_P0.018––
CPU_VCCST_PWRGD0.443––
CPU_VIDALERT_R_L0.544––
CPU_VIDSCLK_R0.293––
CPU_VIDSOUT_R0.299––
CPU_VR_PROCHOT_L0.526––
CPU_VR_READY0.515––
CPUBMONSNS_ALERT_L0.059 LIKE ON BRD PROBLEM––
CPUCORE_BOOT10.601––
CPUCORE_BOOT1_RC0.016––
CPUCORE_BOOT20.602––
CPUCORE_BOOT2_RC0.016––
CPUCORE_FB0.424––
CPUCORE_FCCM0.605––
CPUCORE_GL10.432––
CPUCORE_GL20.433––
CPUCORE_IMON0.630––
CPUCORE_ISEN10.633––
CPUCORE_ISEN20.633––
CPUCORE_ISNS1_N0.019––
CPUCORE_ISNS1_P0.019––
CPUCORE_ISNS2_N0.190––
CPUCORE_ISNS2_P0.019––
CPUCORE_ISUMN_R0.269––
CPUCORE_ISUMP0.498––
CPUCORE_PHASE10.019–15.600R
CPUCORE_PHASE20.019–15.600R
CPUCORE_PWM10.613––
CPUCORE_PWM20.613––
CPUGT_BOOT10.602––
CPUGT_BOOT1_RC0.012––
CPUGT_BOOT20.601––
CPUGT_BOOT2_RC0.012––
CPUGT_COMP0.630––
CPUGT_FB0.606––
CPUGT_FCCM0.606––
CPUGT_GL20.462––
CPUGT_IMON0.631––
CPUGT_ISEN10.632––
CPUGT_ISEN20.631––
CPUGT_ISNS1_N0.013––
CPUGT_ISNS1_P0.013––
CPUGT_ISNS2_N0.013––
CPUGT_ISNS2_P0.013––
CPUGT_ISUMN_R0.265––
CPUGT_ISUMP0.488––
CPUGT_NTC0.632––
CPUGT_PHASE10.013–13.200R
CPUGT_PHASE20.013–13.200R
CPUGT_PWM10.612––
CPUGT_PWM20.611––
CPUGT_RTN0.001––
CPUSA_BOOT0.602––
CPUSA_COMP0.630––
CPUSA_FB0.587––
CPUSA_FCCM0.615––
CPUSA_IMON0.631––
CPUSA_ISNS_N0.040––
CPUSA_ISNS_P0.040––
CPUSA_ISUMN_R0.297––
CPUSA_ISUMP0.581––
CPUSA_LGATE0.430––
CPUSA_PHASE0.039––
CPUSA_PWM0.609––
CPUSA_SW_LL0.040–26.400R
CPUSA_UGATE0.570––
CPUTHMSNS_ADDR_SEL0.655 LIKE ON BRD PROBLEM––
CPUTHMSNS_ALERT_L0.000 LIKE ON BRD PROBLEM––
CPUTHMSNS_D2_N0.6560.655 LIKE ON BRD PROBLEM––
CPUTHMSNS_D2_P0.6550.662 LIKE ON BRD PROBLEM––
CPUTHMSNS_DUR_SEL0.368 LIKE ON BRD PROBLEM––
CPUTHMSNS_TH_SEL0.367 LIKE ON BRD PROBLEM––
CPUVR_PROG10.628––
CPUVR_PROG20.623––
CPUVR_PROG30.605––
CPUVR_PROG40.632––
CPUVR_PROG50.631––
CPUVR_VIDSCLK0.342––
CPUVR_VIDSOUT0.309––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.508––
DP_INT_AUX_NOL––
DP_INT_AUX_POL––
DP_INT_HPD0.770––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
DP_XA_AUXCH_N0.792––
DP_XA_AUXCH_P0.792––
DP_XA_HPD0.471––
DP_XA_ML_N<0>OL––
DP_XA_ML_N<1>OL––
DP_XA_ML_N<2>OL––
DP_XA_ML_N<3>OL––
DP_XA_ML_P<0>OL––
DP_XA_ML_P<1>OL––
DP_XA_ML_P<2>OL––
DP_XA_ML_P<3>OL––
EDP_BKLT_EN0.549––
EDP_BKLT_PWM0.762––
EDP_PANEL_PWR0.779––
HDA_BIT_CLK0.791––
HDA_RST_L0.791––
HDA_SDIN00.771––
HDA_SDOUT0.791––
HDA_SYNC0.791––
HIPWR_EN0.637––
I2C_BKLT_SCL0.512––
I2C_BKLT_SDA0.546––
I2C_CAM_SCK0.736––
I2C_CAM_SDA0.735––
I2C_UPC_SCL0.730––
I2C_UPC_SDA0.726––
I2C_UPC_XA_DBG_CTL_SCL0.753––
I2C_UPC_XA_DBG_CTL_SDA0.753––
INLET_THMSNS_D1_N0.6560.664 LIKE ON BRD PROBLEM––
INLET_THMSNS_D1_P0.6570.666 LIKE ON BRD PROBLEM––
ISNS_HS_COMPUTING_IOUT0.705––
ISNS_HS_COMPUTING_N0.360––
ISNS_HS_COMPUTING_P0.360––
ISNS_HS_GAIN_N0.3690.534 LIKE ON BRD PROBLEM––
ISNS_HS_GAIN_OUTOL––
ISNS_HS_GAIN_P0.542 LIKE ON BRD PROBLEM––
JTAG_WLAN_SEL0.780––
JTAG_WLAN_TDI0.784––
L_AMP1_GAIN0.346––
L_AMP2_GAIN0.001––
LCD_IRQ_L0.770––
LCD_PWR_SLEW0.625––
LCDBKLT_EN_LOL––
LPC_PWRDWN_L0.574––
LPC_SERIRQ0.565––
MEM_A_CAA<0>0.285––
MEM_A_CLK_N<0>0.300––
MEM_A_CLK_P<0>0.302––
MEM_A_CS_L<0>0.284––
MEM_A_DQS_N<1>0.294––
MEM_A_DQS_P<1>0.295––
MEM_CAM_A<8>0.441––
MEM_CAM_CS_L0.440––
MIPI_CLK_CONN_N0.407––
MIPI_CLK_CONN_P0.409––
MIPI_CLK_N0.405––
MIPI_DATA_CONN_N0.411––
MIPI_DATA_CONN_P0.412––
MIPI_DATA_N0.407––
MIPI_DATA_P0.413––
MLB_RAMCFG00.786––
NAND_OVERTMP_ALERT_L0.575––
P0V9_FIXED_SW0.290––
P0V9_REG_SW00.225––
P0V9_REG_SW10.225––
P1V2_CAM_SRVLXC_PHASE0.300––
P1V2_DRVH0.760––
P1V2_DRVL0.470––
P1V2_HOT_SW0.323––
P1V2_SW0.150––
P1V2_SW_LL0.235––
P1V2S5SW_FB0.775––
P1V2S5SW_FB_R0.364––
P1V2S5SW_HSMUX_EN0.355––
P1V2S5SW_HSMUX_EN_R0.762––
P1V2S5SW_PGOOD0.768––
P1V2S5SW_SW0.360––
P1V8_HOT_SW0.371––
P1V8S3_EN0.495––
P1V8SUS_PGOOD0.451––
P1V35_CAM_SRVLXD_PHASE0.260––
P1VS0_RAMP0.723––
P1VS3_RAMP0.359––
P1VSUS_SW_LL0.235–104.600R
P2V7NAND_AGND0.000––
P2V7NAND_DRVH0.834––
P2V7NAND_DRVH_R0.839––
P2V7NAND_DRVL0.450––
P2V7NAND_LL0.373––
P2V7NAND_N0.375––
P2V7NAND_OCSET0.540––
P2V7NAND_P0.375––
P2V7NAND_R0.375––
P2V7NAND_RTN_DIV0.539––
P2V7NAND_SENSE_DIV0.540––
P2V7NAND_SET00.545––
P2V7NAND_SET10.545––
P2V7NAND_SREF0.544––
P2V7NAND_SW_LL0.375––
P3V3_G3H_REG_FB0.374––
P3V3G3H_BOOT0.584––
P3V3G3H_SW0.35––
P3V3S5_COMP20.743––
P3V3S5_CSN20.382––
P3V3S5_CSP21.414––
P3V3S5_DRVH0.936––
P3V3S5_DRVL0.559––
P3V3S5_EN0.521––
P3V3S5_RF0.597––
P3V3S5_SW20.380––
P3V3S5_TG0.933––
P3V3S5_VBST0.566––
P3V3S5_VFB20.585––
P3V3S5_VSW0.390––
P5VP3V3_VREF20.492––
P5VP3V3_VREG30.565––
P5VS4_COMP10.750––
P5VS4_CSN10.351––
P5VS4_CSP11.418––
P5VS4_DRVH0.900––
P5VS4_DRVL0.552––
P5VS4_EN0.593––
P5VS4_PGOOD0.451––
P5VS4_VBST0.629––
P5VS4_VFB10.593––
P5VS4_VSW0.350––
PANEL_P5V_EN0.577––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.482––
PBUSVSENS_EN_L_DIVOL––
PCH_BSSB_CLK0.776––
PCH_BSSB_DATA0.775––
PCH_BT_UART_CTS_L0.498––
PCH_BT_UART_D2R0.500––
PCH_BT_UART_R2D0.429––
PCH_BT_UART_RTS_L0.429––
PCH_HSIO_PWR_EN0.573––
PCH_INTRUDER_L0.815––
PCH_RTCRST_L0.814––
PCH_SRTCRST_L0.816––
PCH_STRP_TOPBLK_SWP_L0.561––
PCH_UPC_XA_SWD_DATA0.818––
PCIE_CAMERA_D2R_N0.380––
PCIE_CAMERA_D2R_P0.379––
PCIE_CLK100M_SSD_N0.347––
PCIE_CLK100M_SSD_P0.350––
PCIE_CLK100M_TEST_N0.355––
PCIE_CLK100M_TEST_P0.353––
PCIE_SSD_D2R_N<0>0.381––
PCIE_SSD_D2R_P<0>0.384––
PCIE_TEST_D2R_N0.381––
PCIE_TEST_D2R_P0.390––
PCIE_TEST_R2D_N0.359––
PCIE_TEST_R2D_P0.356––
PD_L0.497––
PDCINVSENS_EN_L_DIVOL––
PICCOLO_IUVD0.558––
PICCOLO_NOR_CS_L0.377––
PICCOLO_PID10.556––
PICCOLO_POK10.510––
PICCOLO_POK20.568––
PICCOLO_VEN10.519––
PICCOLO_VREF0.559––
PLT_RST_L0.377––
PM_BATLOW_L0.613––
PM_CLK32K_SUSCLK_R0.576––
PM_DSW_PWRGD0.747––
PM_PCH_PWROK0.443––
PM_PWRBTN_L0.715––
PM_RSMRST_L0.462––
PM_SLP_S0S3_L0.491––
PM_SLP_S3_L0.461––
PM_SLP_S4_L0.455––
PM_SLP_S5_L0.543––
PM_SLP_SUS_L0.454––
PM_SYSRST_L0.555––
PM_THRMTRIP_L0.336––
PMIC_SYS_PWROK0.448––
POWER_GATE_EN0.633––
PP0V9_PLL_DVDD8110.220––
PP0V9_S0SW_SSD_CORE0.225––
PP0V9_S0SW_SSD_FIXED0.290––
PP0V675_CAM_VREF0.651––
PP0V675_MEM_CAM_VREFCA0.528––
PP1V_S0SW0.002––
PP1V_S0SW_PCHCLK0.929––
PP1V_S30.265––
PP1V_S5_PCH_DCPDSW0.360––
PP1V_SUS0.235–104.600R
PP1V_SUS_PCH_VCCCLK40.226––
PP1V_SUS_PCH_VCCCLK50.226––
PP1V_SUSRS0SW_PCHCLK0.225––
PP1V_SUSSW_HSIO0.226––
PP1V_SUSSW_PCH_VCCAMPHYPLL0.226––
PP1V1_UPC_XA_LDO_BMC0.487––
PP1V2_CAM0.300––
PP1V2_CAM_PCIE_PVDD_FLT0.348––
PP1V2_CAM_PCIE_VDD_FLT0.348––
PP1V2_CAM_XTALPCIEVDD0.348––
PP1V2_S0SW0.236––
PP1V2_S0SW_SSD_COLD0.273––
PP1V2_S30.235––
PP1V2_S4SW_SSD_HOT0.325––
PP1V2_S5_SMC_VDDC0.515––
PP1V2_S5SW0.360––
PP1V5_S00.423––
PP1V8_CAM0.502––
PP1V8_PLL_AVDD470.314––
PP1V8_PLL_AVDD8110.314––
PP1V8_PLL_C_AVDD0.314––
PP1V8_S0SW_SSD_COLD0.290––
PP1V8_S30.450––
PP1V8_S4SW_SSD_HOT0.371––
PP1V8_SUS0.420––
PP1V8A_UPC_XA_LDO0.496––
PP1V8D_UPC_XA_LDO0.458––
PP1V35_CAM0.260––
PP2V7_NAND_PVCC0.441––
PP2V7_NAND_VCC0.441––
PP2V9_SYSCLK0.461––
PP3V0_S5_AVREF_SMC0.592––
PP3V3_G3H0.35––
PP3V3_G3H_KBD_F0.354––
PP3V3_PMICLDO0.419––
PP3V3_S00.360––
PP3V3_S0_CPUTHMSNS_R0.4040.011 LIKE ON BRD PROBLEM––
PP3V3_S0SW_LCD0.612––
PP3V3_S40.478––
PP3V3_S4_TPAD_F0.416––
PP3V3_S50.358––
PP3V3_S5_SMC_VDDA0.360––
PP3V3_SUS0.360––
PP3V3_UPC_VIN0.569––
PP3V3_UPC_XA_LDO0.512––
PP3V3R2V7_NAND_VCC0.375––
PP3V3R3V0_AON0.571––
PP5V_G3H0.453––
PP5V_S00.466––
PP5V_S0_ALSCAM_F0.466––
PP5V_S0_CPUCORE10.483––
PP5V_S0_CPUCORE20.483––
PP5V_S0_CPUGT10.484––
PP5V_S0_CPUGT20.483––
PP5V_S0_KBD_F0.466––
PP5V_S0SW_LCD0.577––
PP5V_S3_CPUVR_VCC0.346––
PP5V_S40.350––
PP5V_S4_TPAD_F0.164––
PP5V_S4RS00.483––
PP5V_S50.441––
PP20V_USBC_XA_VBUS_F0.572––
PPBUS_G3H0.360––
PPBUS_G3H_TPAD_FLT0.360––
PPBUS_S0_LCDBKLT_FUSED0.360––
PPBUS_S0_LCDBKLT_PWR_SW0.440––
PPBUS_S5_HS_COMPUTING_ISNS0.360––
PPBUS_SW_BKL0.440––
PPBUS_SW_LCDBKLT_PWR0.356––
PPDCIN_G3H0.560––
PPDCIN_G3H_CHGR0.560––
PPLCDBKLT_VDDA0.481––
PPLCDBKLT_VDDD0.481––
PPVBAT_G3H_CHGR_R0.360––
PPVBAT_G3H_CHGR_REG0.360––
PPVBAT_G3H_CONN0.689––
PPVBUS_LIO0.572––
PPVCCG0_S0_CPU0.020––
PPVCCG1_S0_CPU0.021––
PPVCCGT_S0_CPU_PH10.013–13.200R
PPVCCGT_S0_CPU_PH20.013–13.200R
PPVCCIO_S00.180––
PPVCCSA_DDR_S00.047––
PPVCCSA_S00.040––
PPVCCSA_S0_CPU0.040–26.400R
PPVCORE_S0_CPU0.019––
PPVCORE_S0_CPU_PH10.019–15.600R
PPVCORE_S0_CPU_PH20.019–15.600R
PPVCORE_S0_GT0.013––
PPVCORE_SUS_PCH0.250–66.700R
PPVIN_G3H_P3V3G3H0.537––
PPVIN_S0_CPUVR_VIN0.369––
PPVOUT_S0_LCDBKLT0.635––
PPVREF_S3_MEM_VREFCA0.727––
PPVREF_S3_MEM_VREFDQ_A0.762––
PPVREF_S3_MEM_VREFDQ_B0.769––
PPVRTC_G3H0.440––
PVCC_SW_LL0.250–66.700R
PVCCIO_DRVH0.706––
PVCCIO_DRVL0.471––
PVCCIO_EN0.427––
PVCCIO_SW0.175––
PVCCIO_SW_LL0.180––
PVCCPCORE_EN0.451––
PVCCPCORE_PGOOD0.437––
PWM_KEYB0.544––
RF_0_ANTOL––
RF_1_ANTOL––
S3X_COLD_BOOT_L0.426––
S3X_DDR_CKE10.476––
S3X_HOLD_RESET0.424––
S3X_I2C_SCL0.420––
S3X_I2C_SDA0.417––
S3X_JTAG_SEL0.425––
S3X_JTAG_TCK0.427––
S3X_JTAG_TMS0.425––
S3X_PERST_L0.424––
S3X_PFN0.425––
S3X_PMIC_CTRL00.425––
S3X_PMIC_LOW_PWR0.428––
S3X_RESET_L0.426––
S3X_VDDR12_CK_PLANE0.276––
S5_PWR_EN0.654––
S5_PWRGD0.495––
SMBUS_PCH_CLK0.762––
SMBUS_PCH_DATA0.759––
SMBUS_SMC_0_S0_SCL0.723––
SMBUS_SMC_0_S0_SDA0.723––
SMBUS_SMC_1_S0_SCL0.5520.402 LIKE ON BRD PROBLEM––
SMBUS_SMC_1_S0_SDA0.5530.439 LIKE ON BRD PROBLEM––
SMBUS_SMC_3_SCL0.720––
SMBUS_SMC_3_SDA0.720––
SMBUS_SMC_4_G3_SCL0.713––
SMBUS_SMC_4_G3_SDA0.713––
SMBUS_SMC_5_G3_SCL_R0.430––
SMBUS_SMC_5_G3_SDA_R0.430––
SMC_ACTUATOR_DISABLE_L0.732––
SMC_BC_ACOK0.61––
SMC_CBC_ON0.617––
SMC_CHGR_INT_L0.617––
SMC_CLK12M_EN0.463––
SMC_DEBUGPRT_RX_L0.728––
SMC_DEBUGPRT_TX_L0.727––
SMC_DEV_SUPPLY_L0.749––
SMC_LID0.752––
SMC_LSOC_RST0.637––
SMC_ONOFF_L0.747––
SMC_OOB1_R2D_L0.554––
SMC_PCH_SUSACK_L0.571––
SMC_PCH_SUSWARN_L0.573––
SMC_PM_G2_EN0.521––
SMC_PME_S4_WAKE_L0.732––
SMC_PROCHOT0.778––
SMC_PROCHOT_L0.600––
SMC_RESET_L0.731––
SMC_RST_L0.611––
SMC_SENSOR_PWR_EN0.752––
SMC_TCK0.728––
SMC_TDI0.745––
SMC_TDO0.745––
SMC_THRMTRIP0.833––
SMC_THRMTRIP_L0.455––
SMC_TMS0.728––
SMC_USBC_INT_L0.714––
SMC_VIBE_L0.732––
SMC_WAKE_SCI_L0.571––
SMC_WIFI_PWR_EN0.447––
SPI_ALT_CLK0.692––
SPI_ALT_CS_L0.561––
SPI_ALT_IO<2>0.564––
SPI_ALT_IO<3>0.558––
SPI_ALT_MISO0.554––
SPI_ALT_MOSI0.563––
SPI_IO<2>0.552––
SPI_IO<3>0.553––
SPI_MISO0.549––
SPI_MLB_CLK0.590––
SPI_MLB_CS_L0.668––
SPI_MLB_IO<2>0.557––
SPI_MLB_IO<3>0.557––
SPI_MLB_MISO0.554––
SPI_MLB_MOSI0.562––
SPI_MLBROM_CS_L0.665––
SPIROM_USE_MLB0.561––
SPKRAMP_LOUT1_N0.470––
SPKRAMP_LOUT1_P0.470––
SPKRAMP_LOUT2_N0.470––
SPKRAMP_LOUT2_P0.470––
SPKRAMP_ROUT1_N0.475––
SPKRAMP_ROUT1_P0.472––
SPKRAMP_ROUT2_N0.478––
SPKRAMP_ROUT2_P0.473––
SPKRVNDR_L_IDOL––
SPKRVNDR_R_IDOL––
SSD_BOOT_L0.422––
SSD_DEBUG_UART_D2R0.521––
SSD_DEBUG_UART_R2D0.522––
SSD_PWR_EN_L0.785––
SSD_RESET_L0.492––
SSD_SR_EN_L0.529––
STORAGE_EN0.567––
SYS_DETECTOL––
SYS_DETECT_L0.526––
SYSCLK_CLK12M_SMC0.444––
SYSCLK_CLK24M_CAMERA0.441––
SYSCLK_CLK24M_SSD0.407––
SYSCLK_CLK24M_X10.458––
SYSCLK_CLK24M_X20.461––
SYSCLK_CLK24M_X2_R0.463––
SYSCLK_CLK32K_CAMERA_BT_AP0.423––
TBT_X_RTD3_CIO_PWR_EN0.001––
TEST_CLKREQ_L0.793––
TP_CPU_CFG30.334––
TP_CPU_PWRGD0.424––
TP_ITP_PMODE0.460––
TP_JTAG_WLAN_TCK0.784––
TP_JTAG_WLAN_TDO0.615––
TP_JTAG_WLAN_TMS0.784––
TP_JTAG_WLAN_TRST0.785––
TP_MCP_DC_A50.003––
TP_MCP_DC_A640.017––
TP_MCP_DC_B640.017––
TP_MCP_DC_BN640.231––
TP_MCP_DC_BP10.003––
TP_MCP_DC_BP620.003––
TP_MCP_DC_BP640.231––
TP_MCP_DC_D10.003––
TP_MCP_RSVD_AY180.379––
TP_MCP_RSVD_AY220.391––
TP_MCP_RSVD_BA170.378––
TP_MCP_RSVD_BA230.394––
TP_MCP_RSVD_BG470.379––
TP_MCP_RSVD_BJ150.803––
TP_MCP_RSVD_BJ170.802––
TP_MCP_RSVD_BL640.383––
TP_MCP_RSVD_BN10.802––
TP_PCH_SLP_LAN_L0.573––
TP_PCH_SLP_WLAN_L0.572––
TP_PM_SLP_A_L0.571––
TP_S3X_JTAG_TDI0.428––
TP_S3X_JTAG_TDO0.427––
TP_S3X_JTAG_TRST_L0.426––
TP_S3X_VSS_S0.003––
TP_XDP_BPM_L<0>0.335––
TP_XDP_CPU_PRDY_L0.303––
TP_XDP_CPU_PREQ_L0.321––
TP_XDP_PCH_TCK0.380––
TPAD_SPI_CLK_R0.781––
TPAD_SPI_CS_L0.773––
TPAD_SPI_IF_EN0.772––
TPAD_SPI_INT_L0.772––
TPAD_SPI_MISO_R0.782––
TPAD_SPI_MOSI_R0.782––
TS_HOST_RST0.631––
UNCONNECTED_3400.651 LIKE ON BRD PROBLEM––
UPC_I2C_INT_L0.722––
UPC_XA_5V_EN0.772––
UPC_XA_HPD_RX0.773––
UPC_XA_I2C_ADDR0.001––
UPC_XA_R_OSC0.506––
UPC_XA_ROM_HOLD_L0.664––
UPC_XA_ROM_WP_L0.661––
UPC_XA_SPI_CLK0.715––
UPC_XA_SPI_CLK_R0.710––
UPC_XA_SPI_CS_L0.707––
UPC_XA_SPI_CS_R_L0.689––
UPC_XA_SPI_MISO0.679––
UPC_XA_SPI_MISO_R0.654––
UPC_XA_SPI_MOSI0.688––
UPC_XA_SPI_MOSI_R0.665––
UPC_XA_SWD_CLK0.769––
UPC_XA_SWD_DATA0.802––
UPC_XA_UART_RXTX0.765––
USB_EXTA_N0.578––
USB_EXTA_OC_L0.753––
USB_EXTA_P0.574––
USB_TEST_N0.569––
USB_TEST_P0.568––
USB_UPC_XA_F_N0.578––
USB_UPC_XA_F_P0.574––
USB3_EXTA_D2R_C_NOL––
USB3_EXTA_D2R_C_POL––
USB3_EXTA_D2R_N0.380––
USB3_EXTA_D2R_P0.379––
USB3_EXTA_R2D_NOL––
USB3_EXTA_R2D_POL––
USBC_X_POC_RESET0.773––
USBC_XA_CC10.610––
USBC_XA_CC20.590––
USBC_XA_I2C_EN0.755––
USBC_XA_SBU1OL––
USBC_XA_SBU2OL––
USBC_XA_USB_BOT_NOL––
USBC_XA_USB_BOT_POL––
USBC_XA_USB_TOP_NOL––
USBC_XA_USB_TOP_POL––
WLAN_ROM_CLK0.701––
WLAN_ROM_CS0.688––
WLAN_ROM_MISO0.674––
WLAN_ROM_MOSI0.702––
WLAN_ROM_ORG0.715––
XDP_CPUPCH_TCK0.057––
XDP_CPUPCH_TDI0.321––
XDP_CPUPCH_TDO0.282––
XDP_CPUPCH_TMS0.320––
XDP_CPUPCH_TRST_L0.327––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00244?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00244: diode 0.360. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00244?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00244: diode 0.35. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00244?

OpenBoardData's known-good values for PP5V_S5 on the 820-00244: diode 0.441. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00244 board?

Open your own 820-00244 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License