Apple laptop board · OpenBoardData

820-3787 known-good readings

Known-good readings for the Apple laptop board 820-3787: 1,436 nets, including 104 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 103 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3787.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 104 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.302 DIODE0.3183.4203.420 Lid closed3.450 Start3.420 While charging the battery–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on this board; the "G3H" suffix indicates it stays present whenever power is connected, based on the name rather than a schematic.

Known-good readings from the archive:

  • Diode to ground, board unpowered: 0.302 and 0.318.
  • Voltage with power applied: 3.420 V, 3.420 V with the lid closed, 3.450 V at start, and 3.420 V while charging the battery.

To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading well below the known-good range usually points to a short or a leaky part on the rail; a missing or low voltage points to the rail's supply or an overload. No known-good resistance reading is available for this rail.

PP3V42_G3H_SMC_SPVSR0.317––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is a 3.42 V always-on rail feeding the SMC's SPVSR input, judged from the name (G3H = always on). The only known-good figure here is a diode reading of 0.317 to ground; no known-good voltage reading is recorded for this rail. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the net. A diode value far from 0.317 suggests a short or a leaky part on the rail, but a small difference can be normal, so compare with a matching net before condemning anything.

PPBUS_G3H0.44912.500 Start–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this board, and the "G3H" in its name indicates it is an always-on rail. The archive lists a known-good diode reading of 0.449 to ground and a voltage of 12.500 V at the "Start" condition. Check it with the board unpowered in diode mode from PPBUS_G3H to ground, then power up and measure the voltage. A diode reading far from 0.449 usually points to a short or a leaky component on the rail; a voltage well off 12.500 V at startup suggests the rail isn't coming up. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

PPBUS_G3H_R0.46012.500 Start–
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main always-on power bus; the "G3H" in its name marks it as an always-on rail (from the name). Known-good readings in the archive: diode 0.460 and 12.500 V at the Start condition.

  • Check it unpowered in diode mode from PPBUS_G3H_R to ground; a value well below 0.460 suggests a short or leaky load on the rail.
  • Then power the board and measure the voltage; it should sit near 12.500 V at startup.
  • A far-off voltage points to the rail not coming up or being pulled down, but one reading alone doesn't confirm a bad part.

No known-good resistance reading is recorded for this rail.

PPDCIN_G3HOL20.000 Start–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, judging from its name: the DC input that should be present whenever the charger is connected. The archive lists diode OL and 20.000 V at Start as its readings; treat these as a community guide, not a guaranteed value. To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage. A far-off voltage or a shorted diode reading usually points to a fault on the input path or a shorted load, but no known-good resistance reading exists here, so compare against a matching net or a known-good board before condemning anything.

PPDCIN_G3H_CHGR0.65220.000 Start–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in the name indicates it is always-on, present whenever the charger is connected. The archive lists a diode reading of 0.652 and a voltage of 20.000 V at the Start condition; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then with the charger connected measure the voltage. A diode reading far below 0.652 usually points to a short or a leaky part on the rail; no known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

PPDCIN_G3H_INRUSH0.6520.020 Start––
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is the inrush-limited DC input rail that feeds the G3H (always-on) section, judging from the name. The archive lists two diode readings to ground: 0.652 and 0.020 (the 0.020 marked "Start"), so treat these as a guide and note the condition each was taken in. Check it unpowered in diode mode from the rail to ground, then measure the DC voltage with the charger connected. A reading near 0.020 suggests a short or very low impedance on that rail, while a much higher or open reading points to a broken path or missing source; no known-good voltage reading is recorded here, so compare against a matching input net or a known-good board.

PPDCIN_G3H_ISOLOL20.000 Start–
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is the isolated DC-input rail, and the G3H part of its name indicates it is always-on (from the name). The archived reading shows diode OL and 20.000 V at the Start stage, which is a guide only and depends on the board's state. To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage. No known-good resistance reading is recorded here. A voltage far below 20.000 V at Start usually points to a problem upstream in the input path rather than at this rail itself.

PPVBAT_G3H_CHGR_R0.4560.012 Start––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — reference note

  • From the name, this is the battery/charger-side rail: PPVBAT is the battery supply, CHGR the charger section, and G3H the always-on (G3H) domain. It is present whenever the charger side has power, not only when the board is running.
  • Known-good readings from the archive: diode 0.456 to ground, and diode 0.012 in the Start condition. These are community readings and vary with board state, so treat them as a guide only.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage on the rail.
  • A diode reading far below known-good usually points to a short or a leaky part on that rail; a far higher one can mean an open trace or missing part. There is no known-good voltage reading here, so compare against a matching rail or a known-good board.
  • No part list is available for this net, so the likely culprit can't be narrowed from the data alone; confirm with further measurements before replacing anything.
PPVBAT_G3H_CHGR_REG0.4560.012 Start––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From the name, PPVBAT_G3H_CHGR_REG is a charger-side regulated rail tied to the battery/always-on G3H domain. The "G3H" part of the name indicates it is always on.
  • Known-good readings: The archive lists diode 0.456 and diode 0.012 (Start) for this net. These are community readings and only a guide; no known-good voltage reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground, then apply power and measure the rail voltage.
  • What a far-off reading suggests: A diode reading near 0.012 (Start) is very low and usually points to a short or a heavy load on the rail; 0.456 is the higher reference. A voltage that is missing or wrong with power applied points to the charger circuit or its supply, but that is a likely cause, not a confirmed one.
PPVBAT_G3H_CONNOL DIODEOL12.500 Start–
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H supply, judged from the name (G3H = always on, CONN = connector). Known-good readings here: diode OL in diode mode, and 12.500 V at the Start condition. Check it with the board unpowered and the battery disconnected, black probe on ground and red on the net in diode mode, then measure the voltage with power applied. A diode reading far below OL suggests a short or leaky part on that rail; no known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPVIN_G3H_P3V42G3H0.63419.940 Start–
AI: what PPVIN_G3H_P3V42G3H is and how to check it

PPVIN_G3H_P3V42G3H is the always-on G3H input rail, judging from its name; it's the feed into the P3V42G3H regulator. The archive lists a known-good diode reading of 0.634 and a startup voltage of 19.940 (condition: Start) — treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.634 usually points to a short or a damaged component on that rail; no known-good resistance value is recorded here.

PPVRTC_G3H0.453––
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on rail for the real-time clock and its backup domain; the G3H suffix (from the name) marks it as present whenever power is connected, not just when the board is switched on. The archive lists one known-good reading: diode 0.453 to ground, with no condition recorded. With the board unpowered, measure diode mode from PPVRTC_G3H to ground and compare; then apply power and check the DC voltage, for which there is no known-good reading here. A diode value far below 0.453 suggests a short or leaky load on the rail, while a much higher or open reading points to a broken trace or missing connection; confirm with a second measurement before suspecting a part.

S5 and SUS: standby 14

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.519––
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: PP1V2_S5_SMC_VDDC is a 1.2 V rail, from its name, tied to the SMC (system management controller) supply and in the S5/SUS standby stage, also from its name. That's a general reading of the name, not confirmed circuit detail.
  • Known-good reading: diode 0.519 to ground, from the community archive; treat it as a guide, since readings vary with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the DC voltage, expecting about 1.2 V.
  • If it's far off: a much lower diode reading or a missing/short voltage points to a short or a failed supply on that rail, but one reading doesn't confirm a bad part. No known-good voltage or resistance value is recorded here, so compare against a matching rail or a known-good board.
PP1V05_SUS0.328––
AI: what PP1V05_SUS is and how to check it
  • What it is: PP1V05_SUS is a 1.05 V standby rail; the "SUS" part of the name marks it as a standby supply, present while the board is in standby. The name is the only source for that.
  • Known-good: diode-to-ground reading of 0.328 in the archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V05_SUS to ground and compare with 0.328; then apply power and measure the rail voltage, expecting about 1.05 V from the name.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a second measurement before replacing anything.
PP3V3_S50.1493.500–
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply (from the name).
  • Known-good readings: diode 0.149 to ground, and 3.500 V with power applied. These come from community readings and are a guide only; no known-good resistance reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S5 to ground, then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a missing or low voltage points to the standby supply not coming up. Confirm with a second reading before replacing anything.
PP3V3_S5_AVREF_SMC0.618––
AI: what PP3V3_S5_AVREF_SMC is and how to check it
  • What it is: From its name, PP3V3_S5_AVREF_SMC is a 3.3 V standby (S5) reference rail feeding the SMC. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.618 to ground, from the readings archive (community-contributed, so treat it as a guide). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.618. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher one suggests an open path. A wrong voltage points at the standby supply or its enable, not necessarily the SMC.
PP3V3_S5_DBGLEDOL––
AI: what PP3V3_S5_DBGLED is and how to check it

PP3V3_S5_DBGLED is a 3.3 V standby rail feeding the debug LED, judging by its name (PP = power rail, 3V3 = 3.3 V, S5 = standby state, DBGLED = debug LED). The only archived reading is a diode-mode value of OL to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on it with power applied and the board in standby. A diode reading far from OL, or a voltage that is missing or pulled low, usually points to a short or a load on the rail rather than the rail itself — but with no known-good voltage here, compare against a matching rail on a known-good board before condemning anything.

PP3V3_S5_SMC_VDDA0.319––
AI: what PP3V3_S5_SMC_VDDA is and how to check it
  • What it is: From the name, PP3V3_S5_SMC_VDDA is a 3.3 V rail in the S5 standby stage, feeding the SMC's analog supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.319 to ground, from the community archive; treat it as a guide, not a spec. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP3V3_SUS0.398 DIODE0.391––
PP5V_S50.463––
AI: what PP5V_S5 is and how to check it
  • What it is: PP5V_S5 is a 5 V standby rail; the "S5" part of the name indicates the standby stage, so it should be present whenever the board has standby power.
  • Known-good reading: diode 0.463 to ground, from the readings archive. This is a community guide, not a factory spec, and no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S5 to ground and compare with 0.463. Then apply power and measure the DC voltage on the rail; it should sit near 5 V, but there is no archived voltage value to compare against.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken trace or missing source. A small difference can be normal, so confirm with a second measurement before suspecting a part.
PP5V_S5_CUMULUS0.425 DIODE0.464––
AI: what PP5V_S5_CUMULUS is and how to check it

PP5V_S5_CUMULUS is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage (from the name, not from a schematic).

  • Known-good diode reading to ground: 0.425 and 0.464 (diode mode, board unpowered). These are community readings and vary with board state, so treat them as a guide.
  • Check it with the board off: diode mode, red probe on ground, black on the rail. Then power up and measure the DC voltage, which should be about 5 V.
  • No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A diode reading far below the known-good range usually points to a short or a leaky part on the rail; a much higher one can mean an open connection. Confirm with a voltage measurement before replacing anything.
PPVIN_S5_HS_COMPUTING_ISNS0.449––
AI: what PPVIN_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From its name, PPVIN_S5_HS_COMPUTING_ISNS is a high-side (HS) computing-rail input (VIN) at the S5 standby stage. The ISNS suffix suggests it's a current-sense related net, but the exact parts on it aren't known here.
  • Known-good reading: Diode mode to ground, 0.449 (community reading, a guide only). No known-good voltage reading is available here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • If far off: A diode reading well below known-good often points to a shorted or leaky component on that net; confirm with a voltage check before replacing anything.
PPVIN_S5_HS_GPU_ISNS0.449––
AI: what PPVIN_S5_HS_GPU_ISNS is and how to check it

PPVIN_S5_HS_GPU_ISNS is a standby-stage rail by its name (S5/SUS), likely a GPU input-current sense line; the exact parts on it aren't known here.

  • Known-good: diode 0.449 to ground, board unpowered (community reading, a guide only).
  • Check: power off, diode mode from the net to ground; then power on and measure its voltage.
  • No known-good voltage reading here, so compare with a matching net or a known-good board.
  • A diode reading far from 0.449 suggests a short or leaky part on that net; confirm before replacing anything.
PPVIN_S5_HS_OTHER3V3_ISNS0.44911.270–
AI: what PPVIN_S5_HS_OTHER3V3_ISNS is and how to check it

PPVIN_S5_HS_OTHER3V3_ISNS — from the name, a standby (S5/SUS) high-side current-sense input for a 3.3 V rail. Known-good from the archive: diode 0.449 to ground, voltage 11.270 (no condition recorded).

  • Check unpowered in diode mode, red lead to ground, black to the net; then power the board and measure the voltage.
  • A diode reading far below 0.449 suggests a short or leaky part on the net; far above suggests an open trace or missing part.
  • No known-good resistance reading here — compare against a matching net or a known-good board.

These are community readings and a guide only; a small difference can be normal.

PPVIN_S5_HS_OTHER5V_ISNS0.449––
AI: what PPVIN_S5_HS_OTHER5V_ISNS is and how to check it

PPVIN_S5_HS_OTHER5V_ISNS is a standby (S5/SUS, from the name) input-voltage sense line for the high-side 5V supply. The only known-good reading here is diode 0.449, with no condition recorded; there is no known-good voltage or resistance reading for this net.

  • Check it unpowered in diode mode to ground and compare with 0.449.
  • Then power the board and measure the voltage on the net.

A diode reading far from 0.449 usually points to a short or a damaged component on that net, but a small difference can be normal, so confirm with the voltage before replacing anything.

PPVOUT_S5_PCH_DCPSUSBYP_R0.369––
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it
  • What it is: From the name, PPVOUT_S5_PCH_DCPSUSBYP_R is a standby (S5/SUS) power rail feeding the PCH's DCPSUSBYP input. The exact parts on it aren't in the archive.
  • Known-good reading: Diode mode to ground, 0.369 (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure its voltage.
  • If it's far off: A much lower diode reading usually points to a shorted load or cap on the rail; confirm with voltage and resistance before replacing anything.

S4 11

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.378 DIODE0.4153.320 Start–
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it. Known-good readings from the archive are diode 0.378 and 0.415 in diode mode, and 3.320 V at start. Check it with the board unpowered in diode mode to ground, then power up and measure the voltage. A diode reading far from those values usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PP3V3_S4_TBT0.4153.300–
AI: what PP3V3_S4_TBT is and how to check it
  • What it is: PP3V3_S4_TBT is a 3.3 V rail in the S4 startup stage, both from its name. "TBT" suggests it feeds Thunderbolt-related circuitry (general naming, not confirmed by board data).
  • Known-good readings: diode 0.415 to ground, and 3.300 V with power applied. These are community readings and a guide only; no known-good resistance value is recorded here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a low or shorted diode reading points to a short on the rail; a correct diode reading with missing voltage points upstream to the rail's enable or supply. Confirm with a second measurement before replacing anything.
PP3V3_S4_TBT_F0.410––
AI: what PP3V3_S4_TBT_F is and how to check it

PP3V3_S4_TBT_F is a 3.3 V rail in the S4 power stage, from its name; "TBT" suggests it feeds Thunderbolt circuitry (general naming, not from board data). The archive lists one known-good reading: diode 0.410, with no condition noted, and no known-good voltage or resistance here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.410 usually points to a short or a leaky part on that rail, but one reading isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP3V3_S4_TBTAPWR0.380––
AI: what PP3V3_S4_TBTAPWR is and how to check it
  • What it is: PP3V3_S4_TBTAPWR is a 3.3 V rail that, from its name, belongs to the S4 startup stage and feeds Thunderbolt power (TBTAPWR). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.380 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplugged, measure diode mode from the rail to ground and compare with 0.380; then power up and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode but no voltage points upstream, to the S4 enable and supply. Confirm with a second measurement before replacing anything.
PP3V3_S4_TBTBPWR0.373––
AI: what PP3V3_S4_TBTBPWR is and how to check it
  • What it is: PP3V3_S4_TBTBPWR is a 3.3 V rail enabled at the S4 power state, judging from its name; the TBT part suggests it feeds Thunderbolt circuitry. This is inferred from the name only.
  • Known-good reading: diode 0.373 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.373. Then power up and measure the voltage; no known-good voltage is listed, so compare against a matching rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one can mean an open trace or missing part. Confirm with a second measurement before replacing anything.
PP3V3RHV_S4_TBTAPWR0.565––
AI: what PP3V3RHV_S4_TBTAPWR is and how to check it

PP3V3RHV_S4_TBTAPWR is a 3.3 V rail, judging from its name, and the S4 in the name puts it at the S4 startup stage. The archive lists a known-good diode reading of 0.565 for it, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is listed here. A diode value far from 0.565 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP3V3RHV_S4_TBTAPWR_F0.565––
AI: what PP3V3RHV_S4_TBTAPWR_F is and how to check it
  • What it is: From the name, PP3V3RHV_S4_TBTAPWR_F is a 3.3 V rail (PP3V3) that is high-voltage-tolerant (RHV), enabled at the S4 startup stage, and tied to Thunderbolt/Thunderbolt adapter power (TBTAPWR). The exact parts on it aren't known here.
  • Known-good reading: diode 0.565 in diode mode to ground, board unpowered. No known-good voltage reading is recorded here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.565. Then power on and measure the rail voltage; it should sit near 3.3 V once the board reaches S4.
  • What a far-off reading suggests: A much lower diode reading points to a short or leaky part on the rail; a much higher or open reading points to a broken trace or missing source. A missing voltage at S4 points upstream to the S4 enable or supply, not necessarily this rail.
PP3V3RHV_S4_TBTBPWR0.566––
AI: what PP3V3RHV_S4_TBTBPWR is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) in the S4 startup stage, feeding Thunderbolt power (TBTBPWR); the "RHV" part isn't explained by the data.
  • Known-good reading: diode 0.566 to ground, from the community archive — a guide, not a guarantee, and no voltage or resistance value is recorded here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to the S4 enable or supply.
PP3V3RHV_S4_TBTBPWR_F0.565––
AI: what PP3V3RHV_S4_TBTBPWR_F is and how to check it
  • What it is: From its name, PP3V3RHV_S4_TBTBPWR_F is a 3.3 V rail in the S4 startup stage, tied to Thunderbolt power (TBTBPWR). "RHV" likely means it stays high-voltage-tolerant or always-on within that stage; that part is inference from the name, not board data.
  • Known-good reading: diode 0.565 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.565. Then apply power and measure the rail voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing connection. One reading alone doesn't confirm a bad part, so recheck and compare against a matching rail before replacing anything.
PP5V_S40.408 DIODE0.4435.000 voltage demarrer–
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging by its name (the S4 part is from the name; the exact function isn't in the data). Known-good readings are diode 0.408 and 0.443 to ground, and 5.000 V with power applied (the data labels that one "voltage demarrer"). Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below those values usually points to a short or a leaky part on the rail; a voltage well off 5.000 V points to the rail not coming up or being loaded down. There's no known-good resistance reading for this rail.

PP5V_S4_AUDIO_XW0.476––
AI: what PP5V_S4_AUDIO_XW is and how to check it
  • What it is: PP5V_S4_AUDIO_XW is a 5 V audio rail that comes up at the S4 stage, judging from the name (general naming convention, not from board data). "XW" likely marks a switched or gated version of the rail.
  • Known-good reading: diode 0.476 to ground. That's the only value recorded here; there is no known-good voltage or resistance reading for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.476. Then apply power and measure the voltage, expecting about 5 V once the board reaches S4.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream, to the enable or switch feeding it. One reading alone doesn't prove a part bad, so confirm with a second measurement before replacing anything.

S3: memory 20

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V75_S3_MEM_VREFCA_B0.373––
AI: what PP0V75_S3_MEM_VREFCA_B is and how to check it
  • What it is: From its name, PP0V75_S3_MEM_VREFCA_B is a 0.75 V memory reference rail that comes up at the S3 (memory) stage. The board data doesn't list which parts sit on it.
  • Known-good reading: Diode 0.373 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.373. Then power on and measure the DC voltage; it should sit near 0.75 V by the name, but that figure isn't from the board data.
  • If it's far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Either way, confirm with a second measurement before replacing anything.
PP0V75_S3_MEM_VREFDQ_A0.380––
AI: what PP0V75_S3_MEM_VREFDQ_A is and how to check it
  • What it is: From its name, PP0V75_S3_MEM_VREFDQ_A is a 0.75 V memory reference rail (VREFDQ) that comes up at the S3 (memory) stage. The board data only gives the net name and its startup stage; it doesn't list which parts sit on it.
  • Known-good reading: diode 0.380 to ground, from the readings archive (community contribution, so treat it as a guide, not a spec). No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the net to ground and compare with 0.380. Then power up and measure the DC voltage, expecting roughly 0.75 V from the name.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with a second measurement before replacing anything.
PP0V75_S3_MEM_VREFDQ_B0.373––
AI: what PP0V75_S3_MEM_VREFDQ_B is and how to check it

PP0V75_S3_MEM_VREFDQ_B — reference note

  • From its name, this is a 0.75 V memory reference rail (VREFDQ) that comes up in the S3 (memory) stage; the "B" suffix suggests one of a pair of reference nets.
  • Known-good from the archive: diode mode to ground 0.373, with no condition recorded. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the net, and compare with the other VREFDQ net if one exists.
  • Then power up and measure the voltage; a diode reading far from 0.373 usually points to a short or a leaky part on that net, but confirm with the voltage before replacing anything.
PP1V35_S30.1261.300–
AI: what PP1V35_S3 is and how to check it

PP1V35_S3 is a 1.35 V rail; the S3 suffix places it at the memory stage of startup, from its name. The archive gives a known-good diode reading of 0.126 to ground and 1.300 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode value far below 0.126 suggests a short or a failing load on the rail; far above it suggests an open path. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP1V35_S3_MEM0.126––
AI: what PP1V35_S3_MEM is and how to check it

PP1V35_S3_MEM is a 1.35 V memory rail in the S3 (suspend-to-RAM) power state, judging from the name. The only known-good figure here is a diode reading of 0.126 to ground, with no condition recorded; no known-good voltage is listed. With the board unpowered, measure diode mode from PP1V35_S3_MEM to ground and compare with 0.126. Then power up and check that the rail comes up at about 1.35 V when the board reaches S3. A diode reading far from 0.126 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP1V35_S3RS0_CPUDDR0.153––
AI: what PP1V35_S3RS0_CPUDDR is and how to check it
  • What it is: From the name, PP1V35_S3RS0_CPUDDR is a 1.35 V rail feeding CPU DDR memory, in the S3 (memory) startup stage. The board data here is a readings archive only, so the parts on the net aren't known.
  • Known-good: Diode reading to ground is 0.153, with no condition recorded. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.153 suggests a short or a leaky load on the rail; a much higher or open reading points to a broken connection or a missing feed. A missing or wrong voltage with power on points upstream, to the rail's supply or enable. Treat 0.153 as a guide only, since community readings vary with board state.
PP1V35_S3RS0_FET0.154––
AI: what PP1V35_S3RS0_FET is and how to check it

PP1V35_S3RS0_FET is a 1.35 V rail; the S3 in its name marks it as a memory-stage rail, and FET suggests it is switched through a FET. The archive lists one known-good diode reading of 0.154 to ground, with no condition recorded and no known-good voltage reading. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board at the S3 stage. A diode reading far from 0.154 usually points to a short or a leaky part on the rail, but one reading is only a guide, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S30.438 DIODE0.443––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail for the S3 (memory) power state, judged from the rail name. Known-good readings are diode 0.438 and 0.443 in diode mode, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and in S3. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from those values usually points to a short or a damaged component on the rail, but confirm with voltage and resistance before replacing anything.

PP3V3_S3_DPMUX_UC_R0.442––
AI: what PP3V3_S3_DPMUX_UC_R is and how to check it
  • What it is: PP3V3_S3_DPMUX_UC_R is a 3.3 V rail, from its name, that comes up at the S3 (memory) stage of startup. The "DPMUX_UC" part of the name suggests it feeds a display mux/level-shift function, but that's inference from the name, not from board data.
  • Known-good reading: diode 0.442 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.442. Then power on and measure the voltage; it should sit near 3.3 V once the board reaches S3.
  • If far off: a much lower diode reading points to a short or leaky part on the rail; a much higher or open reading points to a missing feed or broken trace. One reading alone doesn't condemn a part, so confirm with the voltage measurement before replacing anything.
PP3V3_S3_FAN_CTL0.148––
AI: what PP3V3_S3_FAN_CTL is and how to check it
  • What it is: PP3V3_S3_FAN_CTL is a 3.3 V S3 (memory-stage) fan control rail, judged from its name; the board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.148 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the net to ground; then power on and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the net, but one reading isn't proof — compare with a known-good board before replacing anything.
PP3V3_S3_PSOC0.4113.320 Start–
AI: what PP3V3_S3_PSOC is and how to check it
  • What it is: PP3V3_S3_PSOC is a 3.3 V rail. The "S3" part of the name indicates the memory (S3) startup stage, and "PSOC" points to the PSoC device it feeds. That reading is from the name, not from a schematic.
  • Known-good readings: diode 0.411 and voltage 3.320 V, with the voltage taken at the Start condition. These are community readings and only a guide.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S3_PSOC to ground; then power the board and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good suggests a short or a leaky load on the rail; a missing or low voltage with a normal diode reading points upstream, to the rail's source or its enable. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board before replacing anything.
PP3V3_S3_VREFMRGN0.443––
AI: what PP3V3_S3_VREFMRGN is and how to check it

PP3V3_S3_VREFMRGN is a 3.3 V rail in the S3 (memory) startup stage, judging by its name; the "VREFMRGN" suffix suggests a reference/margin-related supply, though that's general interpretation, not from board data. The only known-good reading here is a diode value of 0.443 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode reading far from 0.443 usually points to a short or a damaged part on that net, but one reading alone isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP3V3_S3RS0_CAMERA0.344––
AI: what PP3V3_S3RS0_CAMERA is and how to check it

PP3V3_S3RS0_CAMERA is a 3.3 V rail that, from its name, belongs to the S3 (memory) startup stage and feeds the camera circuit. The only known-good reading here is a diode value of 0.344 to ground; no known-good voltage reading is recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.344 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S3RS0_CAMERA_R0.344––
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA_R is a 3.3 V rail, from its name, in the S3 (memory/suspend-to-RAM) startup stage, feeding camera circuitry. The "_R" suffix suggests a switched or gated branch.
  • Known-good reading: diode 0.344 in the archive (no condition recorded). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage on the rail.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher or open reading points to a missing connection or open feed. Confirm with the voltage measurement before replacing anything.
PP3V3_S3RS4_BT_F0.380 DIODE0.411––
AI: what PP3V3_S3RS4_BT_F is and how to check it
  • What it is: From the name, PP3V3_S3RS4_BT_F is a 3.3 V rail in the S3 (memory) startup stage, with the BT_F suffix suggesting it feeds the Bluetooth section. This is inferred from the name only.
  • Known-good readings: diode 0.380 and diode 0.411 in diode mode (community archive, guide only; no condition recorded). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with those two figures; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a low or shorted diode reading points to a shorted load or decoupling cap on the rail; an open reading points to a missing feed or enable. Confirm with a second measurement before replacing anything.
PP5V_S30.480––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is a 5 V rail that, judging by its name, comes up at the S3 (memory) stage of the power sequence. The archive lists one known-good reading: diode 0.480 in diode mode to ground, with no condition noted and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.480 usually points to a short or a leaky part on that rail, but confirm with a voltage check before replacing anything.

PP5V_S3_LTUSB_A_F0.514––
AI: what PP5V_S3_LTUSB_A_F is and how to check it

PP5V_S3_LTUSB_A_F is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state and feeds the LTUSB_A section; the exact parts on it aren't known here. The only known-good reading in the archive is a diode value of 0.514 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage and confirm it comes up in S3. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below 0.514 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection or missing part.

PP5V_S3_LTUSB_A_ILIM0.518––
AI: what PP5V_S3_LTUSB_A_ILIM is and how to check it
  • What it is: From the name, a 5 V S3 (memory-stage) rail for the LTUSB A-side current-limit circuit. The board data doesn't list which parts sit on it.
  • Known-good: diode 0.518 to ground, no condition given. No known-good voltage or resistance reading here.
  • How to check: Power off, measure diode mode from the net to ground; then apply power and measure the voltage.
  • If far off: a low diode reading usually points to a shorted part or load on the rail; a high one to an open path. Confirm with the voltage before replacing anything.
PP5V_S3RS0_ALSCAM_F0.371 DIODE0.399––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it
  • What it is: From the name, PP5V_S3RS0_ALSCAM_F is a 5 V rail that comes up at the S3 (memory) stage and feeds the ALS camera circuit. The exact parts on it aren't known here.
  • Known-good readings: diode 0.371 and diode 0.399 in diode mode, with no condition recorded. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground, then power up and measure the voltage.
  • If far from known-good: a low diode reading usually points to a short or leaky part on the rail; a high one to an open feed. Confirm with the voltage before replacing anything.
PPVTTDDR_S30.480––
AI: what PPVTTDDR_S3 is and how to check it

PPVTTDDR_S3 is the DDR termination rail that comes up at the S3 (memory) stage, judging from its name. The archive lists one known-good diode reading of 0.480 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from PPVTTDDR_S3 to ground and compare with 0.480; then apply power and check the rail voltage against a known-good board, since no voltage value is recorded. A diode reading far below 0.480 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

S0: running 46

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V0_S0GPU_ISNS0.174–205.400
AI: what PP1V0_S0GPU_ISNS is and how to check it

PP1V0_S0GPU_ISNS is a 1.0 V GPU sense rail; the "S0" in the name indicates it belongs to the running state, and "ISNS" indicates it's a current-sense line rather than a heavy power rail (from the name).

  • Known-good readings from the archive: diode 0.174 and resistance 205.400. These are community values and vary with board state, so treat them as a guide.
  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running.
  • No known-good voltage reading is recorded here, so compare against a matching net on the other side of the pair or a known-good board.
  • A diode or resistance far below known-good usually points to a short or a leaky part on that net; a value well above can mean an open trace or missing part. One reading alone doesn't confirm a bad part.
PP1V05_S00.095––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V supply rail that is active in the S0 (running) state, judged from its name. The only known-good reading here is a diode value of 0.095 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.095 usually points to a short or a damaged load on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V5_S00.3131.500–
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" suffix, from the name, marks it as a running-state supply. The archive gives a known-good diode reading of 0.313 to ground and 1.500 V with the board powered. Check it unpowered in diode mode from the rail to ground, then confirm 1.500 V with power applied. A diode reading far below 0.313 suggests a short or leaky load on the rail; far above it suggests an open path. No known-good resistance reading is listed here, so compare against a matching rail or a known-good board.

PP1V5_S0_AUDIO_DIG0.3101.500–
AI: what PP1V5_S0_AUDIO_DIG is and how to check it

PP1V5_S0_AUDIO_DIG is the 1.5 V digital audio rail; the "S0" in the name indicates it belongs to the running state. Known-good readings in the archive are a diode value of 0.310 and 1.500 V. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.310 suggests a short or a failing load on the rail; a voltage well off 1.500 V points to a supply or enable problem. No known-good resistance reading is listed for this rail.

PP1V05_S0_PCH_VCC_CLK_F0.093––
AI: what PP1V05_S0_PCH_VCC_CLK_F is and how to check it
  • What it is: From its name, PP1V05_S0_PCH_VCC_CLK_F is a 1.05 V rail that runs in the S0 (running) state and feeds the PCH clock supply. The exact parts on it aren't known here.
  • Known-good reading: diode 0.093 to ground, from the readings archive. This is a community guide, not a factory spec, and it varies with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail; a much higher one suggests an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP1V05_S0_PCH_VCC_CLK_R0.093––
AI: what PP1V05_S0_PCH_VCC_CLK_R is and how to check it

PP1V05_S0_PCH_VCC_CLK_R is a 1.05 V rail that, from its name, supplies the PCH clock section and is active in the S0 (running) state. The archive lists one known-good diode reading of 0.093 to ground; there is no known-good voltage reading here, so compare against a matching rail or a known-good board. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode value far from 0.093 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V05_S0_REG_R0.102––
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V rail; the S0 suffix indicates it belongs to the running (S0) power state, from the name. The only archived reading is a diode value of 0.102 to ground, with no condition recorded and no known-good voltage here. With the board unpowered, measure diode mode from the rail to ground and compare against 0.102; then power up and check the voltage at the rail. A diode reading far below 0.102 usually points to a short or a low-impedance load on the rail, while a far higher one can mean an open path — neither confirms a bad part on its own. No known-good voltage is available for this rail, so compare the powered voltage against a matching rail or a known-good board.

PP1V5R1V35_S0_RIO0.305 DIODE0.311––
AI: what PP1V5R1V35_S0_RIO is and how to check it

PP1V5R1V35_S0_RIO is a running-state (S0, from the name) rail that likely feeds the RIO block at 1.5 V or 1.35 V, though the exact function isn't in the data. Known-good diode readings to ground are 0.305 and 0.311, taken with the board unpowered. Check it in diode mode to ground first, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode reading far from those values usually points to a short or a damaged part on the rail, but confirm with a voltage check before replacing anything.

PP1V5R1V35_S0GPU0.1431.300–
AI: what PP1V5R1V35_S0GPU is and how to check it
  • What it is: From the name, PP1V5R1V35_S0GPU is a GPU rail that runs at either 1.5 V or 1.35 V, and the S0 suffix means it's active in the running (S0) state. The name alone doesn't say which of the two voltages is selected on a given board.
  • Known-good readings: diode 0.143 to ground, and 1.300 V with power applied. These come from community contributions and are a guide, not a guarantee.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If far off: A diode reading well below known-good suggests a short or a failing part on the rail; a voltage that's absent or wrong suggests the rail isn't being enabled or its supply is failing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning anything.
PP3V3_S00.292 DIODE0.3363.3003.320 Start–
AI: what PP3V3_S0 is and how to check it
  • What it is: PP3V3_S0 is a 3.3 V rail that is on in the S0 (running) state, from the name. It's a main always-needed supply once the board is fully on.
  • Known-good readings (community archive, guide only): diode 0.292 and 0.336 in diode mode; voltage 3.300 and 3.320 at start. No known-good resistance reading here.
  • How to check: power off and unplug, then measure diode mode from PP3V3_S0 to ground; then power up and measure the voltage on the rail.
  • If it's far off: a low diode reading or a sagging voltage usually points to a short or heavy load on the rail, but one reading alone doesn't confirm a bad part — compare against a matching rail or a known-good board before replacing anything.
PP3V3_S0_AUDIO_ANALOG0.3373.300–
AI: what PP3V3_S0_AUDIO_ANALOG is and how to check it
  • What it is: From its name, PP3V3_S0_AUDIO_ANALOG is a 3.3 V analog audio rail that is up in the S0 (running) state.
  • Known-good readings (community archive, a guide only): diode 0.337 to ground, voltage 3.300.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If far off: A diode reading well below 0.337 suggests a short or leaky load on the rail; no voltage in S0 points to the rail not being enabled or its source failing. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PP3V3_S0_CPUTHMSNS_R0.391––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R — reference note

  • What it is: a 3.3 V rail, from the name: PP3V3 = 3.3 V supply, S0 = running state, CPUTHMSNS = CPU thermal sensor. So it's the supply for the CPU temperature-sense circuit, live once the board is in S0.
  • Known-good reading: diode 0.391 to ground, from the readings archive. This is a community value and varies with board state, so treat it as a guide. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.391. Then power up and measure the voltage on the rail; no known-good voltage is listed, so compare against a known-good board or the same net on a matching pair.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, and an open or high reading to a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_S0_DPMUX_UC_R0.344––
AI: what PP3V3_S0_DPMUX_UC_R is and how to check it

PP3V3_S0_DPMUX_UC_R is a 3.3 V rail; the S0 in its name indicates it belongs to the running (S0) state, and DPMUX/UC suggests it feeds a display-mux or USB-C related circuit (that part is from the name, not board data).

  • Known-good: diode 0.344 to ground in diode mode, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • A diode reading far from 0.344 suggests a short or a faulty part on that rail; a missing or low voltage with a normal diode reading points more to the supply or enable side.
PP3V3_S0_GPUTHMSNS_R0.391––
AI: what PP3V3_S0_GPUTHMSNS_R is and how to check it
  • What it is: From its name, PP3V3_S0_GPUTHMSNS_R is a 3.3 V rail that runs in the S0 (running) state, tied to GPU thermal sensing. The board data has no part list, so which components sit on it isn't known.
  • Known-good reading: Diode mode to ground, board unpowered: 0.391. That's a community guide, not a guaranteed value. No known-good voltage reading here.
  • How to check: Power off and check diode mode from the rail to ground, then power on and measure the voltage on the rail.
  • If it's far off: A much lower diode reading usually points to a short or a failing part on the rail; a much higher one to an open feed. Confirm with a voltage measurement before replacing anything.
PP3V3_S0_VMON_P7OL––
AI: what PP3V3_S0_VMON_P7 is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) in the S0 running state, with VMON suggesting a voltage-monitor sense point rather than a power source. The exact parts on it aren't known here.
  • Known-good reading: The archive lists diode OL for PP3V3_S0_VMON_P7. No known-good voltage reading is available.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with the OL guide; then power the board and measure the DC voltage at the net.
  • If it's far off: A short or low diode reading points to a fault on that net or its load; a missing voltage with a normal diode reading points upstream toward whatever feeds it. Treat this as a likely cause, not confirmed.
PP3V3_S0GPU0.491––
AI: what PP3V3_S0GPU is and how to check it

PP3V3_S0GPU (820-3787) — the name indicates a 3.3 V rail for the GPU, active in the S0 (running) state.

  • Known-good from the archive: diode mode to ground 0.491 (no condition recorded). No known-good voltage reading here.
  • Check unpowered: diode mode from the rail to ground; a value far below 0.491 usually points to a short or a leaky load on the rail, while a much higher or open reading points to a broken feed or missing part.
  • Then power the board and measure the voltage at the rail; it should sit near 3.3 V in S0. No known-good voltage is listed, so compare against a matching rail or a known-good board.
  • A rail that is low or absent under power, with a normal diode reading, suggests the enable or supply side rather than a shorted load.
PP3V3_S0GPU_MISC0.532––
AI: what PP3V3_S0GPU_MISC is and how to check it

PP3V3_S0GPU_MISC is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "GPU_MISC" suggests it feeds miscellaneous GPU-side circuitry (that part is from the name, not confirmed circuit data). The only known-good reading here is a diode value of 0.532 to ground, with no condition noted and no known-good voltage listed. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board in S0. A diode reading far below 0.532 usually points to a short or a failing load on the rail; a far higher or open reading points to a broken connection. Voltage behaviour is the better guide for whether the rail is actually coming up, since no known-good voltage is recorded.

PP3V3_S0SW_SSD0.659––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a switched 3.3 V rail feeding the SSD, and the S0 in its name indicates it belongs to the running (S0) power state. The only known-good reading here is a diode value of 0.659 to ground, with no condition recorded and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.659 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board.

PP3V3_S0SW_SSD_FLT0.622 DIODE0.680––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) that is switched (SW) and in the S0 running state, feeding the SSD, with FLT likely meaning a filtered or fault-related branch. The exact parts on it aren't known here.
  • Known-good readings: diode 0.622 and diode 0.680 in diode mode, from community readings, so treat them as a guide. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a low diode reading or missing voltage usually points to a short or a failed switch or supply feeding the rail, but confirm with more than one reading before replacing anything.
PP3V3_S0SW_SSD_R0.659––
AI: what PP3V3_S0SW_SSD_R is and how to check it

PP3V3_S0SW_SSD_R is a 3.3 V rail for the SSD, switched, active in the S0 (running) state — that's from the name, not from a schematic. The archive lists one known-good reading: diode 0.659 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage is listed here. A diode reading far below 0.659 suggests a short or leaky load on the rail, while a much higher one can mean an open path — but one reading isn't proof, so compare with a matching rail before replacing anything.

PP5V_S00.374 DIODE0v395.070 Start–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, judged from its name. The archive lists a known-good diode reading of 0.374 to ground and a voltage of 5.070 V at start. To check it, power the board off and measure diode mode from PP5V_S0 to ground, then apply power and measure the voltage. A diode reading far below 0.374 usually points to a short or a leaky load on the rail; a voltage well off 5.070 V points to the rail not coming up or being loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP5V_S0_AUDIO_AMP_L0.4025.000–
AI: what PP5V_S0_AUDIO_AMP_L is and how to check it
  • What it is: From the name, PP5V_S0_AUDIO_AMP_L is the 5 V audio-amplifier rail that comes up in the S0 (running) state. The "_L" suffix is just part of the net name.
  • Known-good readings (community archive, a guide only): diode 0.402 to ground, voltage 5.000 V. No condition is recorded with these, and no resistance value is listed.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Power up and confirm about 5.000 V in S0.
  • If it's far off: A diode reading well below 0.402 suggests a short or leaky load on the rail; no voltage in S0 points to the rail not being enabled or its source missing. Confirm with a second measurement before replacing anything.
PP5V_S0_AUDIO_AMP_R0.469––
AI: what PP5V_S0_AUDIO_AMP_R is and how to check it
  • What it is: From the name, a 5 V rail feeding the audio amplifier, enabled in the S0 (running) state. It is a switched rail, so it should only be present once the board is fully on.
  • Known-good reading: diode 0.469 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from PP5V_S0_AUDIO_AMP_R to ground. Then power up and measure the voltage on the rail while the board is in S0.
  • If it's far off: a diode reading well below 0.469 suggests a short or leaky load on the rail; a missing voltage with a normal diode reading points to the enable or supply side of the switch. These are likely causes, not confirmed ones, so check the enable signal next before replacing anything.
PP5V_S0_BKLT_VDDA0.401––
AI: what PP5V_S0_BKLT_VDDA is and how to check it

PP5V_S0_BKLT_VDDA is a 5 V rail for backlight-related analog supply, and the S0 in its name indicates it belongs to the running (S0) state. The archive lists one known-good reading: diode 0.401 in diode mode to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage reading is recorded here. A diode reading far from 0.401 usually points to a short or a leaky component on that rail, but confirm with a second measurement before replacing anything.

PP5V_S0_BKLT_VDDD0.401––
AI: what PP5V_S0_BKLT_VDDD is and how to check it

PP5V_S0_BKLT_VDDD is a 5 V backlight-related rail that should be present in the S0 (running) state, judging from its name. The archive lists one known-good reading: diode mode to ground 0.401, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.401 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PP5V_S0_CPUVR_VDD0.398––
AI: what PP5V_S0_CPUVR_VDD is and how to check it
  • What it is: From the name, a 5 V rail (PP5V) that is present in the S0 running state and feeds the CPU VRM's VDD supply. It is a power rail, not a signal.
  • Known-good reading: diode 0.398 to ground, from the readings archive; treat it as a guide, since readings vary with board state.
  • How to check: with the board unpowered, measure diode mode from PP5V_S0_CPUVR_VDD to ground, then apply power and measure the DC voltage, expecting about 5 V.
  • If it's far off: a much lower diode reading points to a short or a failed part on the rail; a correct diode reading with no voltage points upstream, to the rail's source or its enable. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A single reading doesn't confirm a bad part; check the source and enable before replacing anything.
PP5V_S0_KBDLED_R0.401––
AI: what PP5V_S0_KBDLED_R is and how to check it

PP5V_S0_KBDLED_R is a 5 V rail for the keyboard backlight, from its name, and the S0 part means it comes up when the board is in its running state. The archive lists one known-good diode reading of 0.401 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage while the backlight should be on. A diode reading far below 0.401 suggests a short or a leaky load on the rail; a far higher one suggests an open path. These are community readings and vary with board state, so treat them as a guide and compare with a matching rail before condemning anything.

PP5V_S0_P1V05S0_VCC0.408––
AI: what PP5V_S0_P1V05S0_VCC is and how to check it
  • What it is: From its name, PP5V_S0_P1V05S0_VCC is a 5 V rail that is up in the S0 (running) state and feeds the 1.05 V S0 supply area. The exact parts on it aren't known here.
  • Known-good reading: diode 0.408 (community archive, a guide; no condition recorded). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a low diode reading usually points to a short or a leaky load on the rail; a high or open reading points to a broken feed. Confirm with the voltage measurement before replacing anything.
PP5V_S0GPU_P1V05_GPU0.400––
AI: what PP5V_S0GPU_P1V05_GPU is and how to check it

PP5V_S0GPU_P1V05_GPU — reference note

  • From its name, this is a 5 V rail (PP5V) that is switched on in the S0 running state and feeds the GPU section; the P1V05_GPU part of the name suggests a related 1.05 V GPU rail, but the exact split isn't documented here.
  • Known-good: diode reading 0.400 to ground, board unpowered. No known-good voltage reading here, and no resistance value.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 0.400. Then power up and measure the voltage on the rail.
  • A diode reading far below 0.400 usually points to a short or a leaky load on the rail; far above it can mean an open path. Confirm with a voltage check before suspecting any part.
PP5V_S0GPU_P1V35_GPU0.402––
AI: what PP5V_S0GPU_P1V35_GPU is and how to check it

PP5V_S0GPU_P1V35_GPU — from the name, a 5 V GPU-related rail (S0 = running state) that also feeds a 1.35 V GPU supply; the exact split isn't clear from the name alone.

  • Known-good: diode reading to ground 0.402 (archive value, a guide only; board state varies). No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • Far from 0.402 in diode mode usually points to a short or a leaky part on that rail — but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.
PPBUS_S0_LCDBKLT_FUSED0.456––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it
  • What it is: From its name, PPBUS_S0_LCDBKLT_FUSED is the fused backlight (LCDBKLT) power rail, active in the S0 running state. It feeds the display backlight circuit.
  • Known-good reading: diode 0.456 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open fuse or broken path. Confirm with the voltage reading before replacing anything.
PPBUS_S0_LCDBKLT_PWR_SW0.912––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it

PPBUS_S0_LCDBKLT_PWR_SW is the switched backlight power rail for the LCD, going by its name: PPBUS is the main bus supply, LCDBKLT is the display backlight, and the S0 suffix means it's live in the running state. The only known-good reading here is a diode value of 0.912 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.912; a much lower reading suggests a short or leaky load on the rail, a much higher one an open path.
  • Then power the board and measure the voltage on the rail in the running state; no known-good voltage is listed, so compare against a matching backlight rail on a known-good board.
  • A reading far from known-good usually points to a fault on the switched backlight path or its load, but that's a likely cause, not a confirmed one.
PPVCC_S0_CPU0.020–32.000R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — rail reference note (820-3787)

  • What it is: from its name, the CPU core supply rail, active in the S0 (running) state. The board data has no part list, so the components on this net aren't known.
  • Known-good readings (community archive, guide only): diode 0.020 to ground, resistance 32.000R. No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then with power applied, measure the voltage on the rail.
  • If far from known-good: a much lower diode or resistance reading usually points to a short or a low-impedance load on the rail, not proof of a bad part. A missing voltage with a normal diode reading points more toward the supply not being enabled or switching.
PPVCC_S0_CPU_PH10.020–32.000R
AI: what PPVCC_S0_CPU_PH1 is and how to check it
  • What it is: From the name, PPVCC_S0_CPU_PH1 is a CPU power rail (VCC) active in the S0 running state; the PH1 suffix suggests one phase of a multi-phase CPU supply. General knowledge, not from board data.
  • Known-good readings: diode 0.020 and resistance 32.000R, from the readings archive. These are community values and vary with board state, so treat them as a guide.
  • How to check: with the board unpowered, diode mode from the rail to ground, then resistance to ground; then power up and measure the rail voltage. No known-good voltage reading here.
  • What a far-off reading means: a much lower diode or resistance reading usually points to a short or a failed phase component on that rail; a much higher one to an open. Confirm with a second measurement before replacing anything.
PPVCC_S0_CPU_PH20.020–32.000R
AI: what PPVCC_S0_CPU_PH2 is and how to check it
  • What it is: From the name, PPVCC_S0_CPU_PH2 is a CPU power rail (VCC for the CPU), active in the S0 running state. The PH2 suffix suggests a phase of a multiphase CPU supply; that part is general interpretation, not board data.
  • Known-good readings: diode 0.020 and resistance 32.000R, with no condition noted. These are a guide only, from community contributions, and vary with board state.
  • How to check: Power off and unplug, then measure diode mode to ground on the rail; then apply power and measure the voltage. No known-good voltage reading is recorded here.
  • If far off: A diode or resistance far from 0.020 / 32.000R points toward a short or a failed phase component, but one reading doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.
PPVCC_S0_CPU_PH30.020–32.000R
AI: what PPVCC_S0_CPU_PH3 is and how to check it

PPVCC_S0_CPU_PH3 is a CPU power rail; the S0 in the name indicates the running state, and PH3 suggests a phase of a multiphase CPU supply (from the name, general interpretation). Known-good from the archive: diode 0.020 and resistance 32.000R — very low, as expected for a CPU core rail. Check it unpowered in diode mode to ground, then measure the voltage with the board running; no known-good voltage reading is recorded here. A diode or resistance far above these values points to an open phase or damaged component, while a hard short to ground points to a failed part on the rail — confirm with a second measurement before replacing anything.

PPVCCIO_S0_CPU0.03––
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is a CPU I/O supply rail, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.03 to ground, with no condition recorded; no voltage or resistance readings are listed for this rail. Check it unpowered in diode mode from the rail to ground, then measure its voltage with the board powered and running. A diode reading far above 0.03 suggests an open or missing connection on the rail, while a value well below it suggests a short to ground; a single reading isn't proof either way.

PPVCOMP_S0_CPU0.058––
AI: what PPVCOMP_S0_CPU is and how to check it
  • What it is: PPVCOMP_S0_CPU is a CPU-related rail; the S0 in the name indicates the running state. The name suggests a CPU compensation or reference node rather than a main power rail, but the exact function isn't documented in the available data.
  • Known-good reading: diode 0.058 to ground, no condition listed. That is a very low diode reading, so treat it as a low-impedance node and expect similar low readings on a healthy board.
  • How to check: with the board unpowered, measure diode mode from the net to ground and compare with 0.058; then power the board and measure the voltage on the net.
  • No known-good voltage is recorded for this rail, so a voltage reading can only be judged against a known-good board or a matching net.
  • If the diode reading is far off: a much lower or shorted reading points to a short on that node; a much higher reading can mean an open connection. Confirm with a second measurement before suspecting any part.
PPVCORE_S0_GFX_PH10.038–30.000R
AI: what PPVCORE_S0_GFX_PH1 is and how to check it

PPVCORE_S0_GFX_PH1 is a graphics core power rail; the name indicates the processor core supply (VCORE) for the GPU (GFX), a phase (PH1), and S0 meaning running state. From the readings archive, the known-good values are a diode reading of 0.038 and a resistance of 30.000R. To check it, power the board off and measure diode mode to ground, then apply power and measure the voltage on the rail. A reading far from these values usually points to a short or a failed component on that rail, but confirm with a second measurement before replacing anything. No known-good voltage reading is available here.

PPVCORE_S0_GFX_PH20.038–30.000R
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 is a graphics core power rail; the S0 in the name indicates it belongs to the running (S0) state, and GFX points to the GPU. The archive lists a diode reading of 0.038 and a resistance of 30.000R for this rail, with no condition noted, so treat them as a guide only. To check it, power the board off and measure diode mode to ground on the rail, then apply power and measure the voltage. A reading far from 0.038 in diode mode, or a very different resistance, usually points to a short or a faulty component on that rail rather than the rail itself. No known-good voltage reading is available here, so compare against a known-good board of the same model.

PPVIN_S0_CPUVR_VIN0.457––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VR (voltage regulator) input rail, active in the S0 running state, judging from its name. The archive lists one known-good diode reading of 0.457 to ground, with no condition noted and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage on it. A diode reading far below 0.457 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection. This is a guide only, so confirm against a matching reading before condemning anything.

PPVOUT_S0_KBDBKLT0.544 DIODE0.603––
AI: what PPVOUT_S0_KBDBKLT is and how to check it
  • PPVOUT_S0_KBDBKLT is a keyboard backlight output rail; the name (PPVOUT = switched output, S0 = running state, KBDBKLT = keyboard backlight) indicates it only comes up once the board is in its running state.
  • Known-good readings from the archive: diode mode to ground 0.544 and 0.603 (both DIODE). No known-good voltage reading is recorded here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with those two figures. Then apply power and measure the voltage on the rail with the board running and the backlight enabled.
  • A diode reading far below known-good usually points to a short or a failing component on the rail; a correct diode reading with no voltage points upstream, toward the enable or supply side. These are guides, not confirmed faults.
PPVOUT_S0_LCDBKLT1.154 DIODE1.24645.000 Start–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the name indicates a switched S0 (running-state) supply for the display backlight, and that reading is from the name, not a schematic.

  • Known-good readings here: diode 1.154 and 1.246 in diode mode, and 45.000 V at Start (startup stage). These are community readings and only a guide.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and the display connected.
  • A diode reading far below known-good usually points to a short or leaky part on the rail; a missing or low voltage with power applied points to the backlight supply or its enable, not the rail itself.
  • No known-good resistance reading here.
PPVOUT_S0_PCH_DCPRTC0.714––
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it
  • What it is: From the name, PPVOUT_S0_PCH_DCPRTC is a VOUT power rail in the S0 (running) state, tied to the PCH's DCPRTC domain. That's general reading of the name, not from board data.
  • Known-good reading: diode 0.714, from the readings archive (community-contributed, so a guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good often points to a shorted load or capacitor on the rail, but one reading doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.
PPVOUT_S0_PCH_DCPSST0.384––
AI: what PPVOUT_S0_PCH_DCPSST is and how to check it

PPVOUT_S0_PCH_DCPSST is a running-state (S0) power output rail feeding the PCH's DCPSST supply, judged from the name. The archive lists one known-good diode reading to ground: 0.384, with no condition noted. Check it unpowered in diode mode, black probe to ground, red to the rail, then confirm the voltage with the board powered in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.384 usually suggests a short or leaky load on the rail, but one reading alone doesn't confirm a bad part.

PPVTT_S0_DDR0.114––
AI: what PPVTT_S0_DDR is and how to check it

PPVTT_S0_DDR is the DDR termination rail; the S0 in the name indicates it's active in the running state. The archive lists one known-good diode reading of 0.114 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.114 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault; compare against a matching rail or a known-good board.

Every net with a reading

NetDiodeVoltageResistance
1V0_GPU_IOUTOL––
4V5_NR0.6701.200–
4V5_REG_EN0.7393.300–
4V5_REG_IN0.4475.000–
ADAPTER_SENSE0.644––
ALL_SYS_PWRGD0.468––
AP_CLKREQ_L0.447––
AP_CLKREQ_Q_L0.433 DIODE0.475––
AP_RESET_CONN_L0.433 DIODE0.477––
AP_RESET_L0.430––
AUD_CONN_HP_LEFT0.706––
AUD_CONN_HP_RIGHT0.704––
AUD_CONN_SLEEVE_XW0.002––
AUD_CONN_TYPEDET0.767––
AUD_HP_PORT_L0.651––
AUD_HP_PORT_R0.660––
AUD_HS_MIC_N0.001––
AUD_HS_MIC_P0.002––
AUD_HSBIAS0.576––
AUD_HSBIAS_FILT0.755––
AUD_HSBIAS_IN0.518––
AUD_HSBIAS_REF0.513––
AUD_I2C_INT_L0.602––
AUD_IP_PERIPHERAL_DET0.696––
AUD_LO2_L_N0.676––
AUD_LO2_L_P0.676––
AUD_LO2_R_N0.676––
AUD_LO2_R_P0.677––
AUD_LO3_L_N0.664––
AUD_LO3_L_P0.670––
AUD_LO3_R_N0.661––
AUD_LO3_R_P0.661––
AUD_SPKRAMP_LIN_N0.677––
AUD_SPKRAMP_LIN_P0.677––
AUD_SPKRAMP_LSUBIN_N0.662––
AUD_SPKRAMP_LSUBIN_P0.662––
AUD_SPKRAMP_RIN_N0.675––
AUD_SPKRAMP_RIN_P0.676––
AUD_SPKRAMP_RSUBIN_N0.661––
AUD_SPKRAMP_RSUBIN_P0.661––
AUD_TYPEDET0.765––
BKL_1_SCL0.533––
BKL_1_SDA0.533––
BKL_FB0.736––
BKL_FET_CNTL0.561––
BKL_FET_CNTL_R0.530––
BKL_ISEN10.652––
BKL_SW0.442––
BKLT_EN_R0.548––
BKLT_EN_R_JERRY0.547––
BKLT_FLT0.743––
BKLT_FLT_RCOL––
BKLT_ISET_KEYB0.687––
BKLT_KEYB10.661––
BKLT_KEYB20.000––
BKLT_PWM_KEYB0.556––
BKLT_SCL0.522––
BKLT_SCL_R0.523––
BKLT_SD0.602––
BKLT_SDA0.524––
BKLT_SDA_R0.524––
BKLT_SENSE_OUT0.740––
BKLT_SYNC0.552––
BUTTON_DISABLE0.58––
CAM_DEBUG_RESET_L0.772––
CAM_GPIO30.773––
CAM_PCIE_RESET_L0.427––
CAM_PCIE_WAKE_L0.524––
CAM_RAMCFG00.774––
CAM_RAMCFG10.774––
CAM_RAMCFG20.773––
CAM_SENSOR_WAKE_L0.824––
CAM_SENSOR_WAKE_L_CONN0.002 DIODE0.001––
CAM_TEST_MODE0.770––
CAM_TEST_OUT0.828––
CAM_XTAL_SEL0.772––
CAMERA_CLKREQ_L0.495––
CAMERA_PWR_EN0.510––
CHGR_ACIN0.5624.562 While charging the battery–
CHGR_AGATE0.6650.005 While charging the battery–
CHGR_AGATE_DIVOL0.008 Start––
CHGR_AMON0.8050.578 While charging the battery–
CHGR_BGATE0.6865.000 Start5.440 While charging the battery–
CHGR_BMON0.7410.054 While charging the battery–
CHGR_BOOT0.60818.080 While charging the battery–
CHGR_CELL0.7331.931 While charging the battery–
CHGR_CSI_N0.66318.500 While charging the battery–
CHGR_CSI_P0.64518.500 While charging the battery–
CHGR_CSI_R_N0.6520.020 Start––
CHGR_CSI_R_P0.6520.020 Start––
CHGR_CSO_N0.45712.880 While charging the battery–
CHGR_CSO_P0.45912.870 While charging the battery–
CHGR_CSO_R_N0.4560.012 Start––
CHGR_CSO_R_P0.4560.012 Start––
CHGR_DCIN0.61418.500 While charging the battery–
CHGR_DCIN_D_R0.607––
CHGR_ICOMP0.7560.005 While charging the battery–
CHGR_ICOMP_RC1.750––
CHGR_LGATE0.4751.882 Start1.570 While charging the battery–
CHGR_PHASE0.45612.500 Start12.900 While charging the battery–
CHGR_RST_L0.5243.380 While charging the battery–
CHGR_SGATE0.6630.022 While charging the battery–
CHGR_SGATE_DIVOL0.008 Start––
CHGR_UGATE0.93215.650 Start16.300 While charging the battery–
CHGR_VCOMP0.7492.085 While charging the battery–
CHGR_VCOMP_ROL––
CHGR_VFRQ0.4990.005 While charging the battery–
CHGR_VNEG0.5470.725 While charging the battery–
CHGR_VNEG_ROL––
CLK25M_CAM_XTALPOL––
CLK25M_CAM_XTALP_ROL––
CODEC_FLYN0.683––
CODEC_FLYP0.4283.300–
CODEC_MICIN20.708––
CODEC_VCOM0.7382.200–
CODEC_VREF_ADC0.764––
CPU_CFG_RCOMP0.051––
CPU_CFG<0>0.275––
CPU_CFG<1>0.276––
CPU_CFG<2>0.276––
CPU_CFG<3>0.277––
CPU_CFG<4>0.263––
CPU_CFG<5>0.263––
CPU_CFG<6>0.278––
CPU_CFG<7>0.277––
CPU_CFG<8>0.276––
CPU_CFG<9>0.278––
CPU_CFG<10>0.280––
CPU_CFG<11>0.278––
CPU_CFG<12>0.277––
CPU_CFG<13>0.278––
CPU_CFG<14>0.278––
CPU_CFG<15>0.276––
CPU_CFG<16>0.278––
CPU_CFG<17>0.277––
CPU_CFG<18>0.277––
CPU_CFG<19>0.278––
CPU_CLK135M_DPLLREF_N0.268––
CPU_CLK135M_DPLLREF_P0.270––
CPU_DC_A4OL––
CPU_DC_A51OL––
CPU_DC_BC1OL––
CPU_DC_BC54OL––
CPU_DC_BF4OL––
CPU_DC_BF51OL––
CPU_DC_D1OL––
CPU_DC_D54OL––
CPU_DIMM_VREFCA0.776––
CPU_DIMMA_VREFDQ0.780––
CPU_DIMMB_VREFDQ0.778––
CPU_EDP_RCOMP0.086––
CPU_MEM_RESET_L0.361––
CPU_MEM_VREFCA_A_ISOL0.379––
CPU_MEM_VREFCA_B_ISOL0.375––
CPU_MEM_VREFDQ_A_ISOL0.382––
CPU_MEM_VREFDQ_B_ISOL0.376––
CPU_PECI0.369––
CPU_PECI_R0.328––
CPU_PEG_RCOMP0.086––
CPU_PROCHOT_L0.091––
CPU_PROCHOT_R_L0.14––
CPU_PWR_DEBUG0.246––
CPU_PWRGD0.363––
CPU_RESET_L0.366––
CPU_SM_RCOMP<0>0.102––
CPU_SM_RCOMP<1>0.076––
CPU_SM_RCOMP<2>0.101––
CPU_THRMTRIP_3V30.744––
CPU_VCCSENSE_N0.002––
CPU_VCCSENSE_P0.022––
CPU_VCCSENSE_P_RC1.556––
CPU_VIDALERT_L0.104––
CPU_VIDALERT_R_L0.147––
CPU_VIDSCLK0.082––
CPU_VIDSCLK_R0.085––
CPU_VIDSOUT0.084––
CPU_VIDSOUT_R0.084––
CPUTHMSNS_ALERT_L0.754––
CPUTHMSNS_D2_N0.760––
CPUTHMSNS_D2_P0.759––
CPUTHMSNS_THM_L0.760––
CPUVDDQ_EN0.560––
CPUVDDQ_EN_L0.571––
CPUVR_BOOT10v59––
CPUVR_BOOT20v59––
CPUVR_BOOT30v59––
CPUVR_COMP0.584––
CPUVR_COMP_RCOL––
CPUVR_DRSEL0.593––
CPUVR_FB_RCOL––
CPUVR_FB20.567––
CPUVR_FCCM0v49––
CPUVR_IMON0.583––
CPUVR_ISEN10.577––
CPUVR_ISEN20.579––
CPUVR_ISEN30.578––
CPUVR_ISNS1_N0.020–32.000R
CPUVR_ISNS1_P0.020–32.000R
CPUVR_ISNS2_N0.020–32.000R
CPUVR_ISNS2_P0.020–32.000R
CPUVR_ISNS3_N0.020–32.000R
CPUVR_ISNS3_P0.020–32.000R
CPUVR_ISUM_IOUT0.586––
CPUVR_ISUM_R_NOL––
CPUVR_ISUM_R_POL––
CPUVR_ISUMN0.021––
CPUVR_ISUMN_R0.464––
CPUVR_ISUMN_RC0.868––
CPUVR_ISUMP0.355––
CPUVR_NTC0.591––
CPUVR_PGOOD0.532––
CPUVR_PHASE10v02–32.000R
CPUVR_PHASE1_K0v01–15R00
CPUVR_PHASE20v02–32.000R
CPUVR_PHASE2_K0v02–15R00
CPUVR_PHASE30v02–32.000R
CPUVR_PHASE3_K0v02–15R00
CPUVR_PROG10.583––
CPUVR_PROG20.581––
CPUVR_PROG30.592––
CPUVR_PWM10v53––
CPUVR_PWM20.523––
CPUVR_PWM30.525––
CPUVR_SLOPE0.581––
CPUVSENSE_IN0.021––
CS4208_HDA_SDOUT0_R0.421––
CS4208_SPDIF_IN0.004––
CS4208_SPDIF_OUT0.686––
DAC_AVDD0.569––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S3OL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DBGLED_S5OL––
DCIN_ISOL_GATE0.7846.800 Start–
DCIN_ISOL_GATE_ROL6.800 Start–
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.510––
DDR3THMSNS_D1_N0.771––
DDR3THMSNS_D1_P0.776––
DDRREG_1V8_VREF0.632––
DDRREG_DRVH0.578––
DDRREG_DRVH_R0.580––
DDRREG_DRVL0.435––
DDRREG_EN0.535––
DDRREG_FB0.686––
DDRREG_LL0.125––
DDRREG_VBST0.618––
DDRREG_VDDQSNS0.126––
DDRREG_VSW0.1261.300–
DDRREG_VTTSNS0.115––
DELAY_1V5S0_PGD0.461––
DFET_CPO10.593––
DFET_CPO20.594––
DFET_OPENCH0.469––
DFET_OPENUS0.465––
DMI_S2N_N<0>0.300––
DMI_S2N_P<0>0.300––
DMIC_CLK30.618 DIODE0.404––
DMIC_CLK3_R0.490––
DMIC_SDA20.001 DIODE0.008––
DMIC_SDA30.746 DIODE0.7810.032 Start–
DP_A_CA_DET_BUF0.651––
DP_A_LSX_ML_N<1>0.763––
DP_B_CA_DET_BUF0.652––
DP_DDC_MUX_CROSSBAR_L0.493––
DP_EXTA_CA_DET_EG0.635––
DP_EXTA_MUX_EN0.494––
DP_EXTB_CA_DET_EG0.636––
DP_EXTB_MUX_EN0.494––
DP_EXTB_MUX_SEL_EG0.495––
DP_INT_AUX_NOL DIODEOL1.590 Start–
DP_INT_AUX_POL DIODEOL1.340 Start–
DP_INT_EG_AUX_N0.788––
DP_INT_EG_HPD0.635––
DP_INT_EG_ML_N<0>0.401––
DP_INT_EG_ML_N<1>0.397––
DP_INT_EG_ML_N<2>0.395––
DP_INT_EG_ML_N<3>0.396––
DP_INT_EG_ML_P<0>0.400––
DP_INT_EG_ML_P<1>0.398––
DP_INT_EG_ML_P<2>0.394––
DP_INT_EG_ML_P<3>0.395––
DP_INT_IG_AUX_N0.315––
DP_INT_IG_AUX_P0.313––
DP_INT_IG_HPD0.647––
DP_INT_IG_ML_N<1>0.313––
DP_INT_IG_ML_N<2>0.316––
DP_INT_IG_ML_N<3>0.314––
DP_INT_IG_ML_P<2>0.315––
DP_INT_IG_ML_P<3>0.312––
DP_INT_ML_C_N<0>0.599––
DP_INT_ML_C_N<1>0.606––
DP_INT_ML_C_N<2>0.605––
DP_INT_ML_C_P<0>0.602––
DP_INT_ML_C_P<1>0.607––
DP_INT_ML_C_P<2>0.605––
DP_INT_ML_N<0>OL DIODEOL––
DP_INT_ML_N<1>OL DIODEOL––
DP_INT_ML_N<2>OL DIODEOL––
DP_INT_ML_N<3>OL DIODEOL––
DP_INT_ML_P<0>OL DIODEOL––
DP_INT_ML_P<1>OL DIODEOL––
DP_INT_ML_P<2>OL DIODEOL––
DP_INT_ML_P<3>OL DIODEOL––
DP_TBT_SEL0.598––
DP_TBTPA_AUXCH_C_N0.568––
DP_TBTPA_AUXCH_C_P0.614––
DP_TBTPA_DDC_CLK0.602––
DP_TBTPA_DDC_DATA0.597––
DP_TBTPA_HPD0.774––
DP_TBTPA_ML_C_N<1>0.327––
DP_TBTPA_ML_C_P<1>0.326––
DP_TBTPA_ML_N<1>0.767––
DP_TBTPA_ML_P<1>0.766––
DP_TBTPB_DDC_CLK0.601––
DP_TBTPB_DDC_DATA0.597––
DP_TBTSNK0_AUXCH_C_N0.547––
DP_TBTSNK0_AUXCH_C_P0.548––
DP_TBTSNK0_EG_AUXCH_N0.573––
DP_TBTSNK0_EG_AUXCH_P0.576––
DP_TBTSNK0_HPD0.552––
DP_TBTSNK0_HPD_EG0.635––
DP_TBTSNK0_HPD_IG0.646––
DP_TBTSNK1_AUXCH_C_N0.542––
DP_TBTSNK1_AUXCH_C_P0.546––
DP_TBTSNK1_EG_AUXCH_N0.575––
DP_TBTSNK1_EG_AUXCH_P0.576––
DP_TBTSNK1_HPD0.564––
DP_TBTSNK1_HPD_EG0.634––
DP_TBTSNK1_HPD_IG0.646––
DPA_EG_DDC_CLK0.630––
DPA_EG_DDC_DATA0.626––
DPA_IG_AUX_CH_N0.367––
DPA_IG_AUX_CH_P0.367––
DPA_IG_DDC_CLK0.568––
DPA_IG_DDC_DATA0.557––
DPB_EG_DDC_CLK0.630––
DPB_EG_DDC_DATA0.626––
DPB_IG_AUX_CH_N0.371––
DPB_IG_AUX_CH_P0.370––
DPB_IG_DDC_CLK0.569––
DPB_IG_DDC_DATA0.565––
DPMUX_HPD_PD0.731––
DPMUX_LRESET_L0.521––
DPMUX_UC_CLK32K0.645––
DPMUX_UC_MD10.618––
DPMUX_UC_MD20.557––
DPMUX_UC_PECI0.731––
DPMUX_UC_PEVREF0.458––
DPMUX_UC_RESET_L0.620––
DPMUX_UC_RX0.600––
DPMUX_UC_TCK0.643––
DPMUX_UC_TDI0.643––
DPMUX_UC_TDO0.643––
DPMUX_UC_TMS0.641––
DPMUX_UC_TRST_L0.644––
DPMUX_UC_TX0.601––
DPMUX_UC_UNUSED0.488––
DPMUX_UC_VCL0.469––
DPMUX_UC_XTAL_ROL––
EDP_IG_BKL_ON0.651––
EDP_IG_PANEL_PWR0.586––
EG_BKLT_EN0.631––
EG_CLKREQ_IN_L0.634––
EG_LCD_PWR_EN0.630––
EG_RESET_L0.635––
ENET_MEDIA_SENSE_RDIV0.459––
FAN_LT_PWM1.038 DIODE1.0750.700 Start–
FAN_LT_TACH2.124 DIODEOL1.680 Start–
FAN_RT_PWM1.043 DIODE1.1050.700 Start–
FAN_RT_TACH2.126 DIODEOL1.660 Start–
FB_A0_MF0.121––
FB_A0_RESET_L0.420––
FB_A0_SEN0.126––
FB_A0_VREFC0.365––
FB_A0_VREFD0.365––
FB_A0_ZQ0.126––
FB_A1_CLK_N0.538––
FB_A1_MF0.121––
FB_A1_RESET_L0.425––
FB_A1_SEN0.125––
FB_A1_VREFC0.363––
FB_A1_ZQ0.122––
FB_B0_DQ<0>0.337––
FB_B0_MF0.122––
FB_B0_RESET_L0.417––
FB_B0_SEN0.126––
FB_B0_ZQ0.122––
FB_B1_MF0.122––
FB_B1_RESET_L0.417––
FB_B1_SEN0.122––
FB_B1_VREFD0.360––
FB_B1_ZQ0.121––
FB_CAL_PD_VDDQ0.183––
FB_CAL_PU_GND0.041––
FB_CAL_TERM_GND0.062––
FB_CLAMP0.524––
FB_CLAMP_TOGGLE_REQ_L0.613––
FB_SW_LEG0.245––
FB_VREF0.697––
FBA0_CK_MID0.554––
FBB1_CK_MID0.548––
FBVDD_ALTVO0.549––
FDI_CSYNC0.361––
FDI_INT0.360––
FW_PME_L0.650––
G3_POWERON_L0.748––
GFXIMVP_BOOT1_R0.557––
GFXIMVP_BOOT2_R0.556––
GFXIMVP_COMP_ROL––
GFXIMVP_FB_GND_ROL––
GFXIMVP_FB_SNS_R0.394––
GFXIMVP_ISNS1_N0.038–30.000R
GFXIMVP_ISNS1_P0.038–30.000R
GFXIMVP_ISNS2_N0.038–30.000R
GFXIMVP_ISNS2_P0.038–30.000R
GFXIMVP_ISUMN0.039––
GFXIMVP_ISUMP_COL––
GFXIMVP_PHASE10.038–30.000R
GFXIMVP_PHASE20.038–30.000R
GFXIMVP_PSI_L0.551––
GFXIMVP_PSI_R_L0.551––
GFXIMVP6_IMON0.553––
GPIO0_SPKR_SHUTDOWN0.529––
GPU_ALT_VREF0.719––
GPU_BUFRSTN0.715––
GPU_FB_VSENSE_IN0.143––
GPU_FBA_DEBUG00.204––
GPU_FBA_DEBUG10.203––
GPU_FBB_DEBUG00.203––
GPU_FBB_DEBUG10.203––
GPU_FBGND_SENSE0.004––
GPU_FBVDDQ_SENSE0.146––
GPU_JTAG_TMS0.730––
GPU_MLS_STRAP20.716––
GPU_OSC_27M_SSIN0.730––
GPU_OSC_27M_XTAL_BUFFOUT_R0.729––
GPU_OSC_27M_XTALIN0.830––
GPU_OSC_27M_XTALOUT0.811––
GPU_PEX_TERMP0.826––
GPU_RESET_R_L0.635––
GPU_ROM_CS_L_ROL––
GPU_ROM_SCLK0.730––
GPU_ROM_SI0.725––
GPU_ROM_SI_ROL––
GPU_SMB_CLK0.718––
GPU_SMB_DAT0.720––
GPU_SSC_SMB_CLK0.714––
GPU_SSC_SMB_DAT0.713––
GPU_TDIODE_N0.501––
GPU_TDIODE_P0.770––
GPU_TESTMODE0.831––
GPUFB_AGND0.002––
GPUFB_DRVH0.590––
GPUFB_GPU_OCSET_R0.145––
GPUFB_GPU_VO_R0.145––
GPUFB_LL0.1431.300156.000R
GPUFB_OCSET0.548––
GPUFB_PGOOD0.538––
GPUFB_SET_R0.551––
GPUTHMSNS_D_N0.756––
GPUTHMSNS_D_P0.755––
GPUVCORE_EN0.539––
GPUVCORE_INVOL––
GPUVCORE_IOUTOL––
GPUVCORE_PGOOD0.538––
GPUVCORE_SENSE_N0.001––
GPUVCORE_SENSE_P0.036––
GPUVSENSE_IN0.037––
HDA_BIT_CLK0.441––
HDA_BIT_CLK_R0.467––
HDA_RST_L0.432––
HDA_RST_R_L0.473––
HDA_SDIN00.399––
HDA_SDOUT0.444––
HDA_SDOUT_R0.472––
HDA_SYNC0.445––
HDMI_EG_CLK_C_N0.370 DIODE0.407––
HDMI_EG_CLK_C_P0.369 DIODE0.406––
HDMI_EG_DATA_C_N<0>0.366 DIODE0.408––
HDMI_EG_DATA_C_N<1>0.369 DIODE0.409––
HDMI_EG_DATA_C_N<2>0.371 DIODE0.406––
HDMI_EG_DATA_C_P<0>0.366 DIODE0.408––
HDMI_EG_DATA_C_P<1>0.368 DIODE0.409––
HDMI_EG_DATA_C_P<2>0.371 DIODE0.406––
HDMI_EG_DDC_CLK1.204 DIODE1.316––
HDMI_EG_DDC_CLK_Q0.795––
HDMI_EG_DDC_DATA1.209 DIODE1.283––
HDMI_EG_DDC_DATA_Q0.794––
HDMI_EG_HPD0.635––
HDMI_HPD0.562 DIODE0.638––
HDMITBTMUX_SEL_TBT0.628––
HS_COMPUTING_IOUT0.712––
HS_GPU_IOUT0.70––
HS_MIC_N2.109––
HS_MIC_P2.070––
HS_OTHER3V3_IOUT0.712––
HS_OTHER5V_IOUT0.715––
I2C_CAM_SCK0.697 DIODE0.770––
I2C_CAM_SDA0.698 DIODE0.770––
I2C_DPMUX_A_SCL0.613––
I2C_DPMUX_A_SDA0.608––
I2C_DPMUX_UC_SCL0.532––
I2C_DPMUX_UC_SDA0.530––
I2C_HDMIRDRV_SCL0.478 DIODE––
I2C_HDMIRDRV_SDA0.479 DIODE0.570––
IFPC_RSET0.797––
IFPD_RSET0.797––
IFPEF_RSET0.797––
ISENSE_P1V35MEM_IOUT0.638––
ISNS_1V35_MEM_N0.127––
ISNS_1V35_MEM_P0.127––
ISNS_1V35_MEM_R_N0.795––
ISNS_1V35_MEM_R_P0.795––
ISNS_AIRPORT_IOUTOL––
ISNS_AIRPORT_R_NOL––
ISNS_AIRPORT_R_POL––
ISNS_CPU_DDR_IOUTOL––
ISNS_GPUFB_IOUT0.637––
ISNS_HS_COMPUTING_N0.449––
ISNS_HS_COMPUTING_P0.449––
ISNS_HS_GPU_N0.449––
ISNS_HS_GPU_P0.449––
ISNS_HS_OTHER3V3_N0.449––
ISNS_HS_OTHER3V3_P0.449––
ISNS_HS_OTHER5V_N0.449––
ISNS_HS_OTHER5V_P0.449––
ISNS_LCDBKLT_N0.456––
ISNS_LCDBKLT_P0.456––
ISNS_S2_OUTOL––
ISNS_S2_R_NOL––
ISNS_S2_R_POL––
ISNS_SSD_IOUT0.647––
ISNS_SSD_N0.659––
ISNS_SSD_P0.659––
ISNS_SSD_R_N0.800––
ISNS_SSD_R_P0.800––
ISNS_TBT_IOUT0.650––
ISNS_TBT_N0.415––
ISNS_TBT_P0.415––
ISNS_TBT_R_N0.797––
ISNS_TBT_R_P0.794––
ISOLATE_CPU_MEM_L0.547––
JTAG_ISP_TCK0.491––
JTAG_ISP_TDI0.455––
JTAG_ISP_TDO0.460––
JTAG_TBT_TCK0.567––
JTAG_TBT_TDI0.530––
JTAG_TBT_TDO0.549––
JTAG_TBT_TMS0.530––
JTAG_TBT_TMS_PCH0.461––
KBDBKLT_RETURN10.613 DIODE0.661––
KBDBKLT_RETURN20.612 DIODE0.656––
KBDBKLT_SW0.401––
LCD_BKLT_EN0.548––
LCD_BKLT_PWM0.543––
LCD_BKLT_PWM_R0.541––
LCD_FSS0.584 DIODE0.6470.028 Start–
LCD_HPD0.628––
LCD_HPD_CONN0.564 DIODE0.6222.820 Start–
LCD_MUX_EN0.639––
LCD_MUX_SEL0.637––
LCD_PANEL_IOUTOL––
LCD_PWR_EN0.627––
LCDBKLT_EN_LOL––
LCDBKLT_IOUTOL––
LED_RETURN_10.605 DIODE0.6471.050 Start–
LED_RETURN_20.603 DIODE0.6441.080 Start–
LED_RETURN_30.613 DIODE0.6571.150 Start–
LED_RETURN_40.603 DIODE0.6471.050 Start–
LED_RETURN_50.603 DIODE0.6441.080 Start–
LED_RETURN_60.612 DIODE0.6561.050 Start–
LPC_AD<0>0.480 DIODE0.5273.320 Start–
LPC_AD<1>0.479 DIODE0.5263.320 Start–
LPC_AD<2>0.479 DIODE0.5393.320 Start–
LPC_AD<3>0.479 DIODE0.5253.320 Start–
LPC_CLK33M_DPMUX_UC0.617––
LPC_CLK33M_LPCPLUS0.550 DIODE0.5821.670 Start–
LPC_CLK33M_LPCPLUS_R0.620––
LPC_CLK33M_SMC0.573––
LPC_CLK33M_SMC_R0.614––
LPC_FRAME_L0.477 DIODE0.5253.320 Start–
LPC_FRAME_R_L0.571––
LPC_PWRDWN_L0.574 DIODE0.6303.320 Start–
LPC_SERIRQ0.568 DIODE0.6042.930 Start–
LPCPLUS_GPIO0.546 DIODE0.6493.290 Start–
LPCPLUS_RESET_L0.503 DIODE0.5623.320 Start–
LSUB_GAIN0.599––
LSUBIN_N0.605––
LSUBIN_P0.605––
MEM_A_A<0>0.150––
MEM_A_A<1>0.156––
MEM_A_A<2>0.150––
MEM_A_A<4>0.150––
MEM_A_A<5>0.153––
MEM_A_A<7>0.149––
MEM_A_A<8>0.156––
MEM_A_A<10>0.153––
MEM_A_A<11>0.153––
MEM_A_A<12>0.149––
MEM_A_A<14>0.150––
MEM_A_BA<0>0.152––
MEM_A_BA<1>0.153––
MEM_A_BA<2>0.150––
MEM_A_CAS_L0.152––
MEM_A_CKE<0>0.148––
MEM_A_CKE<1>0.152––
MEM_A_CLK0_TERM_R0.280––
MEM_A_CS_L<0>0.154––
MEM_A_CS_L<1>0.153––
MEM_A_DQ<13>0.285––
MEM_A_DQ<18>0.284––
MEM_A_DQ<21>0.285––
MEM_A_DQ<38>0.285––
MEM_A_ODT<0>0.149––
MEM_A_ODT<1>0.153––
MEM_A_RAS_L0.149––
MEM_B_A<1>0.149––
MEM_B_A<9>0.148––
MEM_B_A<15>0.147––
MEM_B_BA<2>0.149––
MEM_B_CKE<0>0.147––
MEM_B_CLK0_TERM_R0.272––
MEM_B_CLK1_TERM_R0.273––
MEM_B_DQ<60>0.289––
MEM_CAM_A<14>0.461––
MEM_CAM_CKE0.458––
MEM_CAM_CKE_ROL––
MEM_CAM_ODT0.700––
MEM_CAM_RESET_L0.455––
MEM_CAM_WE_L0.459––
MEM_RESET_L0.400––
MEM_VREFCA_A_RC0.030––
MEM_VREFCA_B_RC0.035––
MEM_VREFDQ_A_RC0.031––
MEMPWR_DIVOL––
MEMRESET_ISOL_LS5V_L0.978––
MEMVTT_EN0.535––
MEMVTT_EN_L0.589––
MIPI_CLK_CONN_N0.367 DIODE0.422––
MIPI_CLK_CONN_P0.366 DIODE0.419––
MIPI_DATA_CONN_N0.369 DIODE0.420––
MIPI_DATA_CONN_P0.369 DIODE0.421––
MLB_RAMCFG00.515––
MLB_RAMCFG20.516––
MLB_RAMCFG30.658––
MULTI_STRAP_REF0.831––
NCOL DIODE––
P1V2_CAM_SRVLXC_PHASE0.303––
P1V5_DIV_VMONOL––
P1V05_EN_D0.872––
P1V05_GPU_AGND0.002––
P1V05_GPU_BOOT_RC0.600––
P1V05_GPU_CS_N0.174–205.400
P1V05_GPU_CS_P0.174–205.400
P1V05_GPU_LL0.173––
P1V05_GPU_LL_FET0.1741.050205.400R
P1V05_GPU_OCSET0.545––
P1V05_GPU_PEX_IOVDD_SNS_N0.003––
P1V05_GPU_PEX_IOVDD_SNS_P0.175––
P1V05_S0GPU_EN0.542––
P1V05_S0GPU_PGOOD0.540––
P1V05_S0GPU_REG_R0.1741.050205.400
P1V05_VID_VMONOL––
P1V05S0_AGND0.005––
P1V05S0_BOOT_RC0.587––
P1V05S0_CS_N0.110––
P1V05S0_CS_P0.096––
P1V05S0_DRVL0.461––
P1V05S0_EN0.563––
P1V05S0_FB0.539––
P1V5S0_FB0.779––
P1V05S0_FSEL0.562––
P1V05S0_LL0.102––
P1V05S0_OCSET0.537––
P1V05S0_PGOOD0.510––
P1V5S0_PGOOD0.566––
P1V05S0_RTN0.536––
P1V05S0_SENSE_N0.007––
P1V05S0_SENSE_P0.100––
P1V05S0_SREF0.559––
P1V5S0_SW0.3131.500–
P1V05S0_VBST0.585––
P1V05S0_VO0.536––
P1V05TBT_SW0.169––
P1V35_CAM_SRVLXD_PHASE0.246––
P1V35CPU_SLEW_CTL0.725––
P1V35GPUFB_EN0.541––
P3V3_SSD_EN_L0.511––
P3V3_SSD_SSOL––
P3V3GPU_EN0.639––
P3V3GPU_EN_L0.502––
P3V3GPU_MISC_EN_L0.505––
P3V3GPU_MISC_SS1.514––
P3V3GPU_SS1.501––
P3V3S0_P1V5_S0_EN0.655––
P3V3S3_EN0.492––
P3V3S3_EN_L0.499––
P3V3S3_S4OL––
P3V3S4_EN_L0.612––
P3V3S5_COMP20.746––
P3V3S5_COMP2_ROL––
P3V3S5_CSN20.149––
P3V3S5_CSP20.926––
P3V3S5_CSP2_R0.154––
P3V3S5_DRVH0.689––
P3V3S5_DRVL0.531––
P3V3S5_EN0.539––
P3V3S5_LL0.1493.500–
P3V3S5_RF0.5943.420 voltage demarrer–
P3V3S5_SNUBROL––
P3V3S5_TG0.689––
P3V3S5_VBST0.570––
P3V3S5_VFB20.585––
P3V3S5_VFB2_R0.149––
P3V3SSD_VMON0.480––
P3V3SUS_EN_L0.648––
P3V3SUS_SSOL––
P3V3WLAN_VMON0.476––
P3V42G3H_BOOST0.633––
P3V42G3H_FB0.728––
P3V42G3H_SHDN_L0.60919.940 Start–
P3V42G3H_SW0.3173.450 Start–
P5V0S0_EN_L0.667––
P5V0S0_SSOL––
P5V1_BIAS0.343––
P5V1_BOOST0.630––
P5V1_FB0.720––
P5V1_SW0.344––
P5V1_VIN0.606––
P5VP3V3_SKIPSEL0.487––
P5VP3V3_VREF20.485––
P5VP3V3_VREG30.568––
P5VS0_EN0.703––
P5VS3_EN0.523––
P5VS3_EN_LOL––
P5VS3_SSOL––
P5VS4_COMP10.745––
P5VS4_COMP1_ROL––
P5VS4_CSN10.443––
P5VS4_CSP11.413––
P5VS4_CSP1_R0.443––
P5VS4_DRVH0.9795.000 voltage demarrer–
P5VS4_DRVL0.535––
P5VS4_EN0.585––
P5VS4_EN_D0.681––
P5VS4_LL0.441––
P5VS4_PGOOD0.583––
P5VS4_SNUBROL––
P5VS4_TG0.984––
P5VS4_VBST0.639––
P5VS4_VFB10.588––
P5VS4_VFB1_R0.441––
P5VS4_VSW0.443––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.486––
PBUSVSENS_EN_L_DIVOL––
PCA9557D_RESET_L0.529––
PCH_CLK14P3M_REFCLK0.474––
PCH_CLK33M_PCIIN0.639––
PCH_CLK33M_PCIOUT0.620––
PCH_CLK96M_DOT_N0.861––
PCH_CLK96M_DOT_P0.857––
PCH_CLK100M_SATA_N0.793––
PCH_CLK100M_SATA_P0.793––
PCH_CLKIN_GNDN0.791––
PCH_CLKIN_GNDP0.792––
PCH_CLKRQ5_L_GPIO440.606––
PCH_CLKRQ7_L_GPIO460.595––
PCH_DIFFCLK_BIASREF0.727––
PCH_DMI_RCOMP0.777––
PCH_DSWVRMEN0.796––
PCH_FDI_RCOMP0.777––
PCH_INTVRMEN_L0.797––
PCH_PCIE_RCOMP0.777––
PCH_PECI0.584––
PCH_PEGCLKRQB_L_GPIO560.597––
PCH_PROCPWRGD0.370––
PCH_RI_L0.651––
PCH_SATA_RCOMP0.778––
PCH_SATALED_LOL––
PCH_SMBALERT_L0.648––
PCH_SML1ALERT_L0.651––
PCH_SPKR0.534––
PCH_SRTCRST_L0.795––
PCH_STRP_TOPBLK_SWP_L0.455––
PCH_SUSACK_L0.531––
PCH_SUSWARN_L0.531––
PCH_TD_IREF0.790––
PCH_USB_RBIAS0.088––
PCI_INTA_L0.734––
PCI_INTB_L0.662––
PCI_INTC_L0.677––
PCIE_AP_D2R_PI_N0.328 DIODE0.344––
PCIE_AP_D2R_PI_P0.332 DIODE0.345––
PCIE_AP_R2D_NOL DIODEOL––
PCIE_AP_R2D_POL DIODEOL––
PCIE_CAMERA_D2R_N0.341––
PCIE_CAMERA_D2R_P0.343––
PCIE_CLK100M_AP_CONN_N0.250 DIODE0.274––
PCIE_CLK100M_AP_CONN_P0.250 DIODE0.274––
PCIE_CLK100M_AP_N0.270––
PCIE_CLK100M_AP_P0.270––
PCIE_CLK100M_CAMERA_N0.273––
PCIE_CLK100M_CAMERA_P0.273––
PCIE_CLK100M_PCH_N0.792––
PCIE_CLK100M_PCH_P0.792––
PCIE_CLK100M_SSD_N0.247 DIODE0.273––
PCIE_CLK100M_SSD_P0.248 DIODE0.273––
PCIE_CLK100M_TBT_N0.275––
PCIE_CLK100M_TBT_P0.278––
PCIE_SSD_D2R_N<0>0.326 DIODE0.340––
PCIE_SSD_D2R_N<1>0.328 DIODE––
PCIE_SSD_D2R_N<2>0.328 DIODE0.339––
PCIE_SSD_D2R_N<3>0.329 DIODE––
PCIE_SSD_D2R_P<0>0.331 DIODE0.342––
PCIE_SSD_D2R_P<1>0.332 DIODE––
PCIE_SSD_D2R_P<2>0.332 DIODE0.342––
PCIE_SSD_D2R_P<3>0.330 DIODE––
PCIE_SSD_R2D_N<0>OL DIODE––
PCIE_SSD_R2D_N<1>OL DIODE––
PCIE_SSD_R2D_N<2>OL DIODE––
PCIE_SSD_R2D_N<3>OL DIODE––
PCIE_SSD_R2D_P<0>OL DIODE––
PCIE_SSD_R2D_P<1>OL DIODE––
PCIE_SSD_R2D_P<2>OL DIODE––
PCIE_SSD_R2D_P<3>OL DIODE––
PCIE_TBT_D2R_N<0>0.322––
PCIE_TBT_D2R_N<1>0.330––
PCIE_TBT_D2R_N<2>0.330––
PCIE_TBT_D2R_N<3>0.327––
PCIE_TBT_D2R_P<0>0.324––
PCIE_TBT_D2R_P<1>0.331––
PCIE_TBT_D2R_P<2>0.334––
PCIE_TBT_D2R_P<3>0.327––
PCIE_TBT_R2D_C_N<0>0.326––
PCIE_TBT_R2D_C_N<1>0.326––
PCIE_TBT_R2D_C_P<1>0.324––
PCIE_WAKE_L0.453 DIODE0.564––
PD_CS4208_GPIO10.745––
PDCINVSENS_EN_L_DIVOL––
PEG_CLK100M_N0.271––
PEG_CLK100M_P0.272––
PEX_CLKREQ_L_R0.634––
PICKB_L0.656 DIODE0.714––
PLT_RESET_L0.518––
PLT_RST_BUF_L0.430––
PM_1V5_PGD_LOL––
PM_1V5_PGD_L_ROL––
PM_BATLOW_L0.512––
PM_CLK32K_SUSCLK_R0.679––
PM_CLKRUN_L0.492 DIODE0.527––
PM_DSW_PWRGD0.739––
PM_MEM_PWRGD0.436––
PM_MEM_PWRGD_LOL––
PM_P1V5_PGD_DIVOL––
PM_PCH_PWROK0.672––
PM_PCH_SYS_PWROK0.736––
PM_PWRBTN_L0.603––
PM_RSMRST_L0.638––
PM_SLP_S3_BUF_L0.565 DIODE0.636––
PM_SLP_S3_L0.506––
PM_SLP_S3_R_L0.482––
PM_SLP_S4_L0.461 DIODE0.490––
PM_SLP_S5_L0.611––
PM_SLP_SUS_L0.682––
PM_SYNC0.370––
PM_SYSRST_L0.632––
PM_THRMTRIP_B_LOL––
PM_THRMTRIP_L0.277––
PM_THRMTRIP_L_R0.484––
PM_WLAN_EN0.428––
PP0V75_S3_MEM_VREFCA_B0.373––
PP0V75_S3_MEM_VREFDQ_A0.380––
PP0V75_S3_MEM_VREFDQ_B0.373––
PP0V675_CAM_VREF0.659––
PP0V675_MEM_CAM_VREFCA0.514––
PP0V675_MEM_CAM_VREFDQ0.659––
PP1V0_S0GPU_ISNS0.174–205.400
PP1V2_CAM0.303––
PP1V2_CAM_PCIE_PVDD_FLT0.353––
PP1V2_CAM_PCIE_VDD_FLT0.353––
PP1V2_CAM_XTALPCIEVDD0.353––
PP1V2_S5_SMC_VDDC0.519––
PP1V05_GPU_FB_DLL_AVDD0.174––
PP1V05_GPU_FB_PLL_AVDD0.173––
PP1V05_GPU_IFPAB_PLLVDD0.334––
PP1V05_GPU_IFPCD_IOVDD0.173––
PP1V05_GPU_IFPEF_IOVDD0.173––
PP1V05_GPU_PEX_PLLVDD0.173––
PP1V05_GPU_PLLVDD0.173––
PP1V05_GPU_SP_PLLVDD0.173––
PP1V05_S00.095––
PP1V5_S00.3131.500–
PP1V5_S0_AUDIO_DIG0.3101.500–
PP1V05_S0_PCH_VCC_CLK_F0.093––
PP1V05_S0_PCH_VCC_CLK_R0.093––
PP1V05_S0_REG_R0.102––
PP1V05_SUS0.328––
PP1V05_TBT0.169––
PP1V05_TBTCIO0.138––
PP1V05_TBTRDV0.148––
PP1V5R1V35_GPU_REG_R0.1431.300–
PP1V5R1V35_S0_RIO0.305 DIODE0.311––
PP1V5R1V35_S0GPU0.1431.300–
PP1V8_CAM0.505––
PP1V8_GPU_IFPA_IOVDD0.552––
PP1V35_CAM0.246––
PP1V35_DDR_CLK0.243––
PP1V35_S30.1261.300–
PP1V35_S3_MEM0.126––
PP1V35_S3RS0_CPUDDR0.153––
PP1V35_S3RS0_FET0.154––
PP3V3_GPU_IFPB_IOVDD0.565––
PP3V3_GPU_IFPX_PLLVDD0.492––
PP3V3_GPU_OVERTEMP0.317––
PP3V3_GPU_PEX_PLL_HVDD0.492––
PP3V3_S00.292 DIODE0.3363.3003.320 Start–
PP3V3_S0_AUDIO_ANALOG0.3373.300–
PP3V3_S0_CPUTHMSNS_R0.391––
PP3V3_S0_DPMUX_UC_R0.344––
PP3V3_S0_GPUTHMSNS_R0.391––
PP3V3_S0_VMON_P7OL––
PP3V3_S0GPU0.491––
PP3V3_S0GPU_MISC0.532––
PP3V3_S0SW_SSD0.659––
PP3V3_S0SW_SSD_FLT0.622 DIODE0.680––
PP3V3_S0SW_SSD_R0.659––
PP3V3_S30.438 DIODE0.443––
PP3V3_S3_DPMUX_UC_R0.442––
PP3V3_S3_FAN_CTL0.148––
PP3V3_S3_PSOC0.4113.320 Start–
PP3V3_S3_VREFMRGN0.443––
PP3V3_S3RS0_CAMERA0.344––
PP3V3_S3RS0_CAMERA_R0.344––
PP3V3_S3RS4_BT_F0.380 DIODE0.411––
PP3V3_S40.378 DIODE0.4153.320 Start–
PP3V3_S4_TBT0.4153.300–
PP3V3_S4_TBT_F0.410––
PP3V3_S4_TBTAPWR0.380––
PP3V3_S4_TBTBPWR0.373––
PP3V3_S50.1493.500–
PP3V3_S5_AVREF_SMC0.618––
PP3V3_S5_DBGLEDOL––
PP3V3_S5_SMC_VDDA0.319––
PP3V3_SUS0.398 DIODE0.391––
PP3V3_TBTLC0.421––
PP3V3_TBTRDV0.554––
PP3V3_TPAD_CONN0.378 DIODE0.412––
PP3V3_WLAN0.501 DIODE0.532––
PP3V3_WLAN_F0.530––
PP3V3_WLAN_R0.530––
PP3V3RHV_S4_TBTAPWR0.565––
PP3V3RHV_S4_TBTAPWR_F0.565––
PP3V3RHV_S4_TBTBPWR0.566––
PP3V3RHV_S4_TBTBPWR_F0.565––
PP3V42_G3H0.302 DIODE0.3183.4203.420 Lid closed3.450 Start3.420 While charging the battery–
PP3V42_G3H_SMC_SPVSR0.317––
PP4V5_AUDIO_ANALOG0.5274.500–
PP5V_S00.374 DIODE0v395.070 Start–
PP5V_S0_AUDIO_AMP_L0.4025.000–
PP5V_S0_AUDIO_AMP_R0.469––
PP5V_S0_BKLT_VDDA0.401––
PP5V_S0_BKLT_VDDD0.401––
PP5V_S0_CPUVR_VDD0.398––
PP5V_S0_KBDLED_R0.401––
PP5V_S0_P1V05S0_VCC0.408––
PP5V_S0GPU_P1V05_GPU0.400––
PP5V_S0GPU_P1V35_GPU0.402––
PP5V_S30.480––
PP5V_S3_LTUSB_A_F0.514––
PP5V_S3_LTUSB_A_ILIM0.518––
PP5V_S3RS0_ALSCAM_F0.371 DIODE0.399––
PP5V_S40.408 DIODE0.4435.000 voltage demarrer–
PP5V_S4_AUDIO_XW0.476––
PP5V_S50.463––
PP5V_S5_CUMULUS0.425 DIODE0.464––
PP5V1_CHGR_VDD0.3415.500 While charging the battery–
PP5V1_CHGR_VDDP0.3385.500 While charging the battery–
PP5VR3V3_SW_LCD0.552 DIODE0.6385.000 Start–
PP5VR3V3_SW_LCD_ISNS0.681––
PP5VR3V3_SW_LCD_UF0.7765.000 Start–
PP15V_TBT0.581––
PP20V_DCIN_CONN_ROL20.000 Start–
PP20V_DCIN_FUSE1.885 DIODEOL––
PPBUS_G3H0.44912.500 Start–
PPBUS_G3H_R0.46012.500 Start–
PPBUS_S0_LCDBKLT_FUSED0.456––
PPBUS_S0_LCDBKLT_PWR_SW0.912––
PPBUS_SW_BKL0.912––
PPBUS_SW_LCDBKLT_PWR0.456––
PPDCIN_G3HOL20.000 Start–
PPDCIN_G3H_CHGR0.65220.000 Start–
PPDCIN_G3H_INRUSH0.6520.020 Start––
PPDCIN_G3H_ISOLOL20.000 Start–
PPVBAT_G3H_CHGR_R0.4560.012 Start––
PPVBAT_G3H_CHGR_REG0.4560.012 Start––
PPVBAT_G3H_CONNOL DIODEOL12.500 Start–
PPVCC_S0_CPU0.020–32.000R
PPVCC_S0_CPU_PH10.020–32.000R
PPVCC_S0_CPU_PH20.020–32.000R
PPVCC_S0_CPU_PH30.020–32.000R
PPVCCIO_S0_CPU0.03––
PPVCOMP_S0_CPU0.058––
PPVCORE_GPU0.038–30.000R
PPVCORE_S0_GFX_PH10.038–30.000R
PPVCORE_S0_GFX_PH20.038–30.000R
PPVIN_G3H_P3V42G3H0.63419.940 Start–
PPVIN_S0_CPUVR_VIN0.457––
PPVIN_S5_HS_COMPUTING_ISNS0.449––
PPVIN_S5_HS_GPU_ISNS0.449––
PPVIN_S5_HS_OTHER3V3_ISNS0.44911.270–
PPVIN_S5_HS_OTHER5V_ISNS0.449––
PPVIN_SW_TBTBST0.541––
PPVOUT_BKLT_FB20.603––
PPVOUT_S0_KBDBKLT0.544 DIODE0.603––
PPVOUT_S0_LCDBKLT1.154 DIODE1.24645.000 Start–
PPVOUT_S0_PCH_DCPRTC0.714––
PPVOUT_S0_PCH_DCPSST0.384––
PPVOUT_S5_PCH_DCPSUSBYP_R0.369––
PPVRTC_G3H0.453––
PPVTT_S0_DDR0.114––
PPVTTDDR_S30.480––
PSOC_F_CS_L0.680 DIODE0.713––
PSOC_MISO0.681 DIODE0.712––
PSOC_MOSI0.681 DIODE0.712––
PSOC_SCLK0.683 DIODE0.714––
RIO_SDCONN_STATE_CHANGE_L0.657 DIODE0.755––
RSUB_GAIN0.652––
RTC_RESET_L0.794––
S0PGD_BJT_GND_R0.100––
S4_PWR_EN0.456––
S5_PWRGD0.578––
SD_PWR_EN0.481 DIODE0.593––
SD_SEL_PCIE_L_USB_H0.640––
SDCONN_OC_L0.719––
SDCONN_STATE_CHANGE_L0.537––
SMBUS_PCH_CLK0.568––
SMBUS_PCH_DATA0.574––
SMBUS_SMC_0_S0_SCL0.663 DIODE0.718––
SMBUS_SMC_0_S0_SDA0.665 DIODE0.717––
SMBUS_SMC_1_S0_SCL0.547––
SMBUS_SMC_1_S0_SDA0.546––
SMBUS_SMC_2_S3_SCL0.671 DIODE0.730––
SMBUS_SMC_2_S3_SDA0.670 DIODE0.538––
SMBUS_SMC_5_G3_SCL0.504 DIODE0.5393.430 Start3.409 While charging the battery–
SMBUS_SMC_5_G3_SDA0.503 DIODE0.5353.430 Start3.402 While charging the battery–
SMC_ADAPTER_EN0.596––
SMC_BC_ACOK0.5463.270 While charging the battery–
SMC_BC_ACOK_VCC0.575––
SMC_BIL_BUTTON_L0.750––
SMC_CHGR_BMON_ISENSE0.747––
SMC_CLK32K0.690––
SMC_CPU_HI_ISENSE0.746––
SMC_CPUPKG_ISENSE0.586––
SMC_CPUPKG_VSENSE0.736––
SMC_DCIN_ISENSE0.745––
SMC_DCIN_VSENSE0.735––
SMC_DEBUGPRT_EN_L0.580––
SMC_DEBUGPRT_RX_L0.681––
SMC_DEBUGPRT_TX_L0.677––
SMC_DELAYED_PWRGD0.707––
SMC_DP_HPD_L0.746––
SMC_EXTAL0.779––
SMC_FAN_0_CTL0.749––
SMC_FAN_1_CTL0.746––
SMC_FAN_1_TACH0.744––
SMC_GFX_OVERTEMP0.692––
SMC_GFX_OVERTEMP_Q0.624––
SMC_GFX_OVERTEMP_R_L0.718––
SMC_GFX_THROTTLE_L0.701––
SMC_GPU_FB_VSENSE0.736––
SMC_GPUCORE_ISENSE0.745––
SMC_LCDBKLT_ISENSE0.743––
SMC_LCDPANEL_ISENSE0.746––
SMC_LID0.5093.400–
SMC_LID_R0.5013.4000.000 Lid closed–
SMC_LRESET_L0.561––
SMC_MANUAL_RST_L0.685––
SMC_ONOFF_L0.676––
SMC_OOB1_D2R_CONN_L0.678 DIODE0.789––
SMC_OOB1_D2R_L0.761––
SMC_OOB1_R2D_CONN_L0.663 DIODE0.699––
SMC_OOB1_R2D_L0.791––
SMC_OTHER3V3_HI_ISENSE0.743––
SMC_P1V35MEM_ISENSE0.744––
SMC_PBUS_VSENSE0.738––
SMC_PECI_L0.740––
SMC_PECI_L_R0.739––
SMC_PM_G2_EN0.536––
SMC_PME_S4_DARK_L0.621––
SMC_PME_S4_WAKE_L0.505––
SMC_PME_SDCONN0.627––
SMC_PROCHOT0.750––
SMC_PWRFAIL_WARN_L0.464 DIODE0.468––
SMC_RESET_L0.478 DIODE0.5223.410 Start–
SMC_ROMBOOT1.028 DIODE1.170––
SMC_RUNTIME_SCI_L0.633––
SMC_RX_L0.718 DIODE0.7583.440 Start–
SMC_S4_WAKESRC_EN0.702––
SMC_S5_PWRGD_VIN0.746––
SMC_SSD_ISENSE0.747––
SMC_SYS_KBDLED0.560––
SMC_TBT_ISENSE0.735––
SMC_TCK0.717 DIODE0.7533.440 Start–
SMC_TDI0.719 DIODE0.7533.440 Start–
SMC_TDO0.718 DIODE0.7473.440 Start–
SMC_THRMTRIP0.745––
SMC_TMS0.715 DIODE0.7463.440 Start–
SMC_TOPBLK_SWP_L0.730––
SMC_TPAD_RST_L0.466––
SMC_TX_L0.716 DIODE0.7503.440 Start–
SMC_VCCIO_CPU_DIV20.736––
SMC_WAKE_L0.751––
SMC_WAKE_SCI_L0.505––
SMC_X29_ISENSE0.746––
SMC_XTAL0.766––
SMC_XTAL_ROL––
SML_PCH_1_CLK0.545––
SML_PCH_1_DATA0.546––
SMS_INT_L0.750––
SPDIF_OUT_JACK0.672––
SPI_ALT_CLK0.544 DIODE0.600––
SPI_ALT_CS_L0.493 DIODE0.5593.320 Start–
SPI_ALT_MISO0.452 DIODE0.4973.320 Start–
SPI_ALT_MOSI0.506 DIODE0.521––
SPI_CLK0.558––
SPI_CS0_L0.527––
SPI_DESCRIPTOR_OVERRIDE1.169––
SPI_DESCRIPTOR_OVERRIDE_L0.750––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.677––
SPI_IO<2>0.548––
SPI_IO<3>0.545––
SPI_MISO0.485––
SPI_MLB_CLK0.539 DIODE0.601––
SPI_MLB_CS_L0.491 DIODE0.561––
SPI_MLB_MISO0.452 DIODE0.513––
SPI_MLB_MOSI0.502 DIODE0.542––
SPI_MOSI0.520––
SPI_SMC_CLK0.558––
SPI_SMC_CS_L0.522––
SPI_SMC_MISO0.496––
SPI_SMC_MOSI0.520––
SPIROM_HOLD_L0.565 DIODE0.542––
SPIROM_USE_MLB0.566 DIODE0.5383.290 Start–
SPIROM_WP_L0.657 DIODE0.677––
SPKR_L_GAIN0.626––
SPKR_R_GAIN0.696––
SPKR_SHUTDOWN0.529––
SPKRAMP_LIN_N0.617––
SPKRAMP_LIN_P0.616––
SPKRCONN_L_ID0.707 DIODE0.744––
SPKRCONN_L_OUT_N0.526 DIODE0.5782.580 Start–
SPKRCONN_L_OUT_P0.518 DIODE0.5832.580 Start–
SPKRCONN_R_ID0.700 DIODE0.745––
SPKRCONN_R_OUT_N0.504 DIODE0.5432.620 Start–
SPKRCONN_R_OUT_P0.506 DIODE0.5322.620 Start–
SPKRCONN_SL_OUT_N0.605 DIODE0.6382.510 Start–
SPKRCONN_SL_OUT_P0.604 DIODE0.6382.510 Start–
SPKRCONN_SR_OUT_N0.598 DIODE0.6312.510 Start–
SPKRCONN_SR_OUT_P0.597 DIODE0.6302.510 Start–
SSD_CLKREQ_CONN_L0.432 DIODE0.466––
SSD_CLKREQ_L0.433––
SSD_DEVSLP1.724 DIODEOL––
SSD_PCIE_SEL_L0.456 DIODE0.499––
SSD_PWR_EN0.445––
SSD_PWR_FET_EN0.415 DIODE0.445––
SSD_RESET_CONN_L0.431 DIODE0.477––
SSD_RESET_L0.437––
SUS_PGOOD_CT0.663––
SYS_DETECT_L1.729 DIODEOL0.033 Start–
SYS_ONEWIRE0.678––
SYS_PWROK_R0.686––
SYSCLK_CLK25M_CAMERA0.459––
SYSCLK_CLK25M_SB0.436––
SYSCLK_CLK25M_SB_R0.565––
SYSCLK_CLK25M_TBT0.452––
SYSCLK_CLK25M_TBT_R0.678––
SYSCLK_CLK25M_X10.453––
SYSCLK_CLK25M_X20.455––
SYSCLK_CLK25M_X2_R0.455––
SYSCLK_CLK32K_RTC0.530––
TBT_A_CIO_SEL0.803––
TBT_A_CONFIG1_BUF0.774––
TBT_A_CONFIG1_RC0.841––
TBT_A_CONFIG2_RC0.814––
TBT_A_D2R_N<1>0.394––
TBT_A_D2R_P<1>0.394––
TBT_A_DP_PWRDN0.797––
TBT_A_HPD0.840––
TBT_A_HV_EN0.478––
TBT_A_LSTX0.761––
TBT_A_R2D_C_P<1>0.236––
TBT_B_CONFIG1_RC0.842––
TBT_B_CONFIG2_RC0.813––
TBT_B_DP_PWRDN0.797––
TBT_B_HPD0.841––
TBT_B_HV_EN0.477––
TBT_BATLOW_L0.801––
TBT_CIO_PLUG_EVENT_L0.499––
TBT_CLKREQ_L0.481––
TBT_EN_CIO_PWR_L0.575––
TBT_MONOBSN0.207––
TBT_MONOBSP0.208––
TBT_PCIE_RESET_L0.430––
TBT_POC_RESET_L0.629––
TBT_PWR_EN0.675––
TBT_PWR_EN_PCH0.601––
TBT_PWR_ON_POC_RST_L0.735––
TBT_PWR_REQ_L0.663––
TBT_RBIAS0.795––
TBT_RSENSE0.001––
TBTACONN_1_COL––
TBTACONN_7_COL––
TBTACONN_20_RC0.578––
TBTAPWRSW_ISET_S00.478––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.478––
TBTAPWRSW_ISET_V3P30.479––
TBTBCONN_1_COL––
TBTBCONN_7_COL––
TBTBCONN_20_RC0.576––
TBTBST_BOOST0.541––
TBTBST_EN_UVLO0.628––
TBTBST_FBXOL––
TBTBST_INTVCC0.582––
TBTBST_PWREN_DIV_LOL––
TBTBST_PWREN_L0.583––
TBTBST_RT0.694––
TBTBST_SHDN_DIV0.618––
TBTBST_SNS10.001––
TBTBST_SNS20.001––
TBTBST_SS0.686––
TBTBST_VC0.700––
TBTBST_VC_RCOL––
TBTBST_VSNS0.577––
TBTDP_AUXIO_EN0.788––
TBTPOCRST_CT0.738––
TP_CAM_JTAG_TCK0.771––
TP_CAM_JTAG_TDI0.771––
TP_CAM_JTAG_TDO0.771––
TP_CAM_JTAG_TMS0.771––
TP_CAM_JTAG_TRST_L0.771––
TP_CAM_LV_JTAG_TCK0.771––
TP_CAM_LV_JTAG_TDI0.771––
TP_CAM_LV_JTAG_TDO0.771––
TP_CAM_LV_JTAG_TMS0.771––
TP_CAM_LV_JTAG_TRSTN0.771––
TP_CAM_TEST_MODE00.773––
TP_CAM_TEST_MODE10.772––
TP_CAM_TEST_MODE20.773––
TP_CPU_FC_VCCST_PWRGDOL––
TP_CPU_RSVD_TP780.271––
TP_DPMUX_UC_P100.644––
TP_DPMUX_UC_P110.646––
TP_DPMUX_UC_P120.645––
TP_DPMUX_UC_P130.645––
TP_DPMUX_UC_P470.644––
TP_GPU_JTAG_TCK0.730––
TP_GPU_JTAG_TDI0.729––
TP_GPU_JTAG_TDO0.730––
TP_GPU_PGOOD20.645––
TP_ISSP_SCLK_P1_10.712––
TP_ISSP_SDATA_P1_00.711––
TP_P7_70.717––
TP_PSOC_P1_30.712––
TP_PSOC_SCL0.711––
TP_PSOC_SDA0.712––
TP_SMC_MD1OL DIODEOL––
TP_SMC_MPM5_LED_CHG0.746––
TP_SMC_TRST_LOL DIODEOL––
TP_SUS_PGOOD_MR_L0.712––
TP_TDM_ONEWIRE_MPMOL DIODEOL––
TPAD_VBUS_EN0.715––
UNCONNECTED_187OL DIODE––
UNCONNECTED_188OL DIODE––
UNCONNECTED_189OL DIODE––
UNCONNECTED_190OL DIODE––
UNCONNECTED_3550v63––
UNCONNECTED_3560v45––
UNCONNECTED_3570v64––
UNCONNECTED_3580v00––
UNCONNECTED_3590v64––
UNCONNECTED_3620v19––
UNCONNECTED_3630v63––
UNCONNECTED_381OL DIODE––
UNCONNECTED_382OL DIODE––
UNCONNECTED_711OL DIODE––
UNCONNECTED_720OL DIODE––
UNCONNECTED_723OL DIODE––
USB_BT_CONN_N0.626 DIODE0.672––
USB_BT_CONN_P0.627 DIODE0.665––
USB_BT_N0.439––
USB_BT_P0.441––
USB_BT_WAKEN0.691––
USB_EXTA_N0.435––
USB_EXTA_OC_L0.491––
USB_EXTA_P0.445––
USB_EXTB_N0.399 DIODE0.494––
USB_EXTB_OC_L0.505 DIODE0.543––
USB_EXTB_P0.400 DIODE0.442––
USB_ILIM0.547––
USB_LT1_N0.662––
USB_LT1_P0.666––
USB_PWR_EN0.491––
USB_TPAD_N0.423––
USB_TPAD_P0.432––
USB3_EXTA_D2R_N0.341––
USB3_EXTA_D2R_P0.342––
USB3_EXTA_R2D_C_N0.370––
USB3_EXTA_R2D_C_P0.370––
USB3_EXTA_R2D_NOL––
USB3_EXTA_R2D_POL––
USB3_EXTB_D2R_N0.343 DIODE0.368––
USB3_EXTB_D2R_P0.342 DIODE0.370––
USB3_EXTB_R2D_C_N0.371––
USB3_EXTB_R2D_C_P0.372––
USB3_EXTB_R2D_NOL DIODEOL––
USB3_EXTB_R2D_POL DIODEOL––
USB3_SD_D2R_N0.326 DIODE0.344––
USB3_SD_D2R_P0.331 DIODE0.347––
USB3_SD_R2D_C_N0.349 DIODE0.372––
USB3_SD_R2D_C_P0.347 DIODE0.370––
VHP_FILTN0.883––
VMON_3V3_DIVOL––
VMON_5V_DIVOL––
VMON_Q2_BASEOL––
VMON_Q3_BASE1.168––
VMON_Q4_BASEOL––
VREF_DAC0.7344.500–
VREFMRGN_CA_A_ENOL––
VREFMRGN_CA_A_EN_RCOL––
VREFMRGN_CA_A_RDIVOL––
VREFMRGN_CA_ABOL––
VREFMRGN_CA_B_ENOL––
VREFMRGN_CA_B_EN_RCOL––
VREFMRGN_CA_B_RDIVOL––
VREFMRGN_DQ_A_ENOL––
VREFMRGN_DQ_A_EN_RCOL––
VREFMRGN_DQ_A_RDIVOL––
VREFMRGN_DQ_B_ENOL––
VREFMRGN_DQ_B_EN_RCOL––
VREFMRGN_DQ_B_RDIVOL––
VREFMRGN_FRAMEBUF_BUFOL––
VREFMRGN_FRAMEBUF_ENOL––
VREFMRGN_MEMVREG_BUFOL––
VREFMRGN_MEMVREG_ENOL––
VREFMRGN_MEMVREG_FBVREFOL––
VTTCLAMP_EN0.611––
VTTCLAMP_L0.125––
WIFI_EVENT_L0.704 DIODE0.745––
WOL_EN0.546––
WS_CONTROL_KBD0.433 DIODE0.467––
WS_CONTROL_KEY0.467––
WS_KBD_ONOFF_L0.683 DIODE1.6833.440 Start–
WS_KBD10.680 DIODE0.710––
WS_KBD20.680 DIODE0.711––
WS_KBD30.680 DIODE0.710––
WS_KBD40.680 DIODE0.711––
WS_KBD50.680 DIODE0.7103.320 Start–
WS_KBD60.680 DIODE0.7103.320 Start–
WS_KBD70.680 DIODE0.7103.320 Start–
WS_KBD80.681 DIODE0.7103.320 Start–
WS_KBD90.680 DIODE0.7113.320 Start–
WS_KBD100.680 DIODE0.7103.320 Start–
WS_KBD110.680 DIODE0.7113.320 Start–
WS_KBD120.681 DIODE0.7103.320 Start–
WS_KBD130.681 DIODE0.7113.320 Start–
WS_KBD140.681 DIODE0.7103.320 Start–
WS_KBD15_C0.713––
WS_KBD15_CAP0.680 DIODE0.8253.320 Start–
WS_KBD16_NUM0.726 DIODE0.711––
WS_KBD16N0.712––
WS_KBD170.680 DIODE0.7103.320 Start–
WS_KBD180.678 DIODE0.7073.320 Start–
WS_KBD190.670 DIODE0.7103.320 Start–
WS_KBD200.680 DIODE0.709––
WS_KBD210.681 DIODE0.711––
WS_KBD220.681 DIODE0.710––
WS_KBD230.682 DIODE0.712––
WS_LEFT_OPTION_KBD0.431 DIODE0.467––
WS_LEFT_OPTION_KEY0.464––
WS_LEFT_SHIFT_KBD0.433 DIODE0.467––
WS_LEFT_SHIFT_KEY0.465––
X29THMSNS_A00.678––
XDP_BPM_L<0>0.276––
XDP_BPM_L<1>0.277––
XDP_BPM_L<2>0.276––
XDP_BPM_L<3>0.276––
XDP_BPM_L<4>0.276––
XDP_BPM_L<5>0.273––
XDP_BPM_L<6>0.274––
XDP_BPM_L<7>0.274––
XDP_CPU_PRDY_L0.272––
XDP_CPU_PREQ_L0.274––
XDP_CPU_PRESENT_L1.276––
XDP_CPU_PWRBTN_L0.604––
XDP_CPU_TCK0.052––
XDP_CPU_TDI0.278––
XDP_CPU_TDO0.144––
XDP_CPU_TMS0.277––
XDP_CPU_VCCST_PWRGD1.357––
XDP_CPUPCH_TRST_L0.052––
XDP_CPURST_L1.505––
XDP_DA1_USB_EXTC_OC_L0.553––
XDP_DA2_SSD_PWR_EN0.446––
XDP_DA3_CAMERA_PWR_EN0.510––
XDP_DB0_USB_EXTB_OC_L0.542––
XDP_DB1_USB_EXTD_OC_L0.539––
XDP_DB2_SD_PWR_EN0.542––
XDP_DB3_SDCONN_STATE_CHANGE_L0.492––
XDP_DBRESET_L0.632––
XDP_DC0_DP_AUXCH_ISOL_L0.498––
XDP_DC2_ODD_PWR_EN_L0.507––
XDP_DC3_JTAG_ISP_TCK0.490––
XDP_DD1_MLB_RAMCFG10.445––
XDP_DD2_ENETSD_CLKREQ_L0.533––
XDP_FC0_HDD_PWR_EN0.507––
XDP_FC1_GPU_GOOD0.510––
XDP_JTAG_CPU_ISOL_L0.577––
XDP_PCH_TCK0.051––
XDP_PCH_TDI0.345––
XDP_PCH_TDO0.337––
XDP_PCH_TMS0.343––
XDP_SYS_PWROK0.740––
XDP_TRST_L0.639––
Z2_CLKIN0.689 DIODE0.716––
Z2_CS_L0.683 DIODE0.713––
Z2_HOST_INTN0.683 DIODE0.747––
Z2_KEY_ACT_L0.679 DIODE0.713––
Z2_MISO0.684 DIODE0.712––
Z2_MOSI0.683 DIODE0.712––
Z2_SCLK0.683 DIODE0.713––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3787?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3787: diode 0.449, voltage 12.500. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3787?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3787: diode 0.318, voltage 3.420. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3787?

OpenBoardData's known-good values for PP5V_S5 on the 820-3787: diode 0.463. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3787 board?

Open your own 820-3787 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License