Apple laptop board · OpenBoardData

820-01949 known-good readings

Known-good readings for the Apple laptop board 820-01949: 1,656 nets, including 100 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 99 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01949.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 100 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 42

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.303––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V rail; the "G3S" suffix marks it as an always-on startup rail, from the name. The only known-good reading here is a diode value of 0.303 to ground, with no condition noted; no known-good voltage reading is available. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.303 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP1V8_G3S_WLANBT0.305––
AI: what PP1V8_G3S_WLANBT is and how to check it

PP1V8_G3S_WLANBT is the 1.8 V supply for the WLAN/Bluetooth section, and the G3S in its name indicates it is an always-on rail. The known-good diode reading is 0.305 to ground, taken with the board unpowered; no known-good voltage reading is recorded here. Check it by measuring diode mode from the rail to ground with power off, then measure the voltage on the rail with power applied. A diode reading far from 0.305 usually points to a short or a leaky component on that rail, but confirm with a voltage measurement before replacing anything.

PP3V_G3H_RTC0.533––
AI: what PP3V_G3H_RTC is and how to check it

PP3V_G3H_RTC is the always-on 3V rail feeding the RTC section; the "G3H" part of the name indicates it stays up whenever power is connected, and "RTC" points to the real-time clock circuit (this is from the name, not from board data).

  • Known-good: diode 0.533 to ground, from the readings archive. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.533 usually points to a short or a leaky part on the rail; a missing or low voltage with a normal diode reading points more to the supply side feeding it.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PP3V3_G3H0.4503.300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is a 3.3 V always-on rail; the "G3H" suffix, from the name, marks it as a startup-stage supply that should be present whenever power is connected. Known-good readings in the archive are a diode value of 0.450 and 3.300 V. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.450 suggests a short or leaky load on the rail; a voltage well off 3.300 V points to the supply or its enable not coming up. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board if needed.

PP3V3_G3H_DFR0.450––
AI: what PP3V3_G3H_DFR is and how to check it

PP3V3_G3H_DFR is an always-on 3.3 V rail, judged from the "G3H" in its name (general naming convention, not board-specific data). The only known-good figure here is a diode reading of 0.450 to ground; no known-good voltage reading is recorded. With the board unpowered, measure diode mode from the rail to ground and compare with 0.450 — a much lower reading usually points to a short or a failing part on the rail, while a much higher one can mean an open path. Then power the board and check the voltage is present, since an always-on rail should come up as soon as power is applied. These are community readings and vary with board state, so treat them as a guide rather than a confirmed fault.

PP3V3_G3H_MESA_SW0.369––
AI: what PP3V3_G3H_MESA_SW is and how to check it

PP3V3_G3H_MESA_SW is a 3.3 V always-on rail, judged from its name: G3H means it should be present whenever power is connected, and MESA_SW suggests a switched branch feeding the MESA section. The only known-good reading here is a diode value of 0.369 to ground; no known-good voltage reading is recorded. With the board unpowered, measure diode mode from the net to ground and compare with 0.369, then apply power and check for about 3.3 V. A diode reading far from 0.369 usually points to a short or a damaged part on that net, but one reading alone doesn't confirm a fault.

PP3V3_G3H_PMU_VDDMAIN0.450––
AI: what PP3V3_G3H_PMU_VDDMAIN is and how to check it

PP3V3_G3H_PMU_VDDMAIN is a 3.3 V always-on rail feeding the PMU's main supply, judged from its name (G3H = always on, VDDMAIN = main supply). The archive lists one known-good diode reading, 0.450, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading here, so compare against a matching always-on rail or a known-good board. A diode reading far from 0.450 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP3V3_G3H_PMU_VINRTC_R0.368––
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check it

PP3V3_G3H_PMU_VINRTC_R is an always-on 3.3 V rail feeding the PMU's RTC input, judging by its name (G3H = always on, VINRTC = RTC supply). The only known-good figure here is a diode reading of 0.368 to ground, with no condition noted; no known-good voltage or resistance is recorded. Check it unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied. A diode reading far from 0.368 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault — compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3H_RSLOC0.369––
AI: what PP3V3_G3H_RSLOC is and how to check it

PP3V3_G3H_RSLOC is a 3.3 V always-on rail; the G3H part of the name indicates it should be present whenever the board has power, even before the main power sequence starts (this is from the name, not from board data).

  • Known-good reading in the archive: diode 0.369 to ground. No known-good voltage reading is recorded here.
  • To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage at the rail.
  • A diode reading far below 0.369 usually points to a short or a leaky load on the rail; a reading far above it can mean an open trace or a missing connection.
  • A missing or low voltage with a normal diode reading points more toward the supply that generates the rail than the rail itself.

These readings are community-contributed guides and vary with board state, so compare against a known-good board where possible.

PP3V3_G3H_RTC0.3423.300–
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC — 3.3 V always-on rail (820-01949)

  • From the name: a 3.3 V rail that is always on (G3H), feeding the RTC section. It should be present whenever the board has power, before the main power sequence starts.
  • Known-good readings from the archive: diode 0.342 to ground, and 3.300 V with power applied. These are community readings and only a guide; the data gives no condition for them.
  • To check: power off and unplugged, measure diode mode from the rail to ground and compare with 0.342. Then apply power and measure the voltage at the rail; it should sit near 3.300 V.
  • A diode reading far below 0.342 suggests a short or a leaky part on the rail; far above suggests an open path. A missing or low voltage with a normal diode reading points upstream, at whatever feeds the rail. No known-good resistance reading is available here, so compare against a matching net or a known-good board.
PP3V3_G3H_RTC_MESA0.369––
AI: what PP3V3_G3H_RTC_MESA is and how to check it
  • What it is: From the name, PP3V3_G3H_RTC_MESA is a 3.3 V always-on rail (G3H) feeding the RTC/MESA area. The archive only has the net name and one reading, so which parts sit on it isn't known.
  • Known-good reading: diode 0.369 to ground, from the community archive, no condition recorded. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.369. Then power up and measure the DC voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open feed. That points to a suspect area, not a confirmed bad part, so trace the feed and check the parts on the rail before replacing anything.
PP3V3_G3H_RTC_REG_R0.3883.300–
AI: what PP3V3_G3H_RTC_REG_R is and how to check it

PP3V3_G3H_RTC_REG_R is an always-on 3.3 V rail feeding the RTC/real-time-clock area; the G3H and RTC parts of the name indicate it should be present whenever the board has power, before the main power sequence. Known-good readings here are diode 0.388 in diode mode and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A far-off diode reading usually points to a short or a damaged component on that rail, while a correct diode but missing voltage points to the regulator or its enable. No known-good resistance reading is recorded here.

PP3V3_G3H_SSD00.3693.300–
AI: what PP3V3_G3H_SSD0 is and how to check it

PP3V3_G3H_SSD0 is a 3.3 V always-on rail feeding the SSD section, based on its name (G3H = always on, SSD0 = first SSD rail). Known-good readings in the archive: diode 0.369 to ground and 3.300 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.369 suggests a short or leaky part on the rail; a missing or low voltage points to the supply feeding it or a load pulling it down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP3V3_G3HSW_DFR0.567––
AI: what PP3V3_G3HSW_DFR is and how to check it

PP3V3_G3HSW_DFR is a 3.3 V rail; the G3H in its name indicates it is always on, and DFR likely marks it as a display-related variant (that part is from the name, not confirmed by data).

  • Known-good: diode reading 0.567 to ground. No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • A diode reading far from 0.567 usually points to a short or leaky part on the rail, but one reading alone doesn't confirm a fault.
PP3V3_G3S0.338––
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is a 3.3 V always-on rail; the G3S suffix comes from its name and marks it as a startup-stage supply. The archive lists one known-good diode reading of 0.338 to ground, with no condition recorded, so treat it as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.338 suggests a short or a leaky load on the rail; no known-good voltage reading is recorded here, so compare against a matching always-on rail or a known-good board.

PP3V3_G3S_KBD0.338––
AI: what PP3V3_G3S_KBD is and how to check it

PP3V3_G3S_KBD is a 3.3 V always-on rail, judged from its name: G3S/G3H rails come up in the always-on startup stage, and "KBD" suggests it feeds the keyboard side. The only archived reading is a diode value of 0.338 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.338. Then power up and check for about 3.3 V, comparing against a matching always-on rail if you have no reference. A diode reading far below 0.338 usually points to a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream at the rail's source.

PP3V3_G3S_TPAD0.338––
AI: what PP3V3_G3S_TPAD is and how to check it

PP3V3_G3S_TPAD is a 3.3 V rail for the trackpad, and the G3S in its name marks it as an always-on rail (that's from the name, not from a schematic). The archive lists one known-good reading: diode 0.338 to ground, with no condition noted. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage. No known-good voltage reading is recorded here, so compare against a matching 3.3 V rail or a known-good board. A diode reading far from 0.338 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_G3S_WLANBT0.338––
AI: what PP3V3_G3S_WLANBT is and how to check it

PP3V3_G3S_WLANBT is the 3.3 V supply for the WLAN/Bluetooth section, and the G3S in its name marks it as an always-on rail (from the name). The archive lists one known-good diode reading of 0.338, with no condition given, and no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.338 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP5V_G3S0.4335.000–
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V rail; the G3S suffix marks it as an always-on (G3H) supply, from the name. The archive lists a known-good diode reading of 0.433 and 5.000 V, with no condition noted.

  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Around 0.433 is the guide.
  • Then power up and measure the rail: about 5.000 V expected.
  • A diode reading far below 0.433 suggests a short or leaky load on the rail; a much higher one suggests an open path. Voltage missing or low points to the supply or its enable, not the load.
  • No known-good resistance reading exists here; compare against a matching rail or a known-good board.
PP5V_G3S_ALSCAM0.433––
AI: what PP5V_G3S_ALSCAM is and how to check it

PP5V_G3S_ALSCAM is a 5 V rail; the G3S part of the name indicates it is an always-on (G3H) supply, and ALSCAM suggests it feeds the ALS/camera section — that reading is from the name, not from board data. The only known-good figure here is a diode reading of 0.433 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far from 0.433 usually points to a short or a leaky load on the rail, but a single reading isn't proof of a bad part — compare against a matching rail or a known-good board before replacing anything.

PP5V_G3S_ALSCAM_F0.433––
AI: what PP5V_G3S_ALSCAM_F is and how to check it

PP5V_G3S_ALSCAM_F is a 5 V rail that, from its name, is a G3S (always-on) supply feeding the camera section. The only known-good reading here is a diode value of 0.433 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check it unpowered: diode mode from PP5V_G3S_ALSCAM_F to ground, black probe on ground. Compare with 0.433.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against the rail's nominal 5 V and a matching always-on 5 V rail.
  • A diode reading far below 0.433 suggests a short or leaky load on the rail; far above suggests an open path. One reading alone doesn't confirm a bad part, so recheck before replacing anything.
PP5V_G3S_CPUREG0.426––
AI: what PP5V_G3S_CPUREG is and how to check it

PP5V_G3S_CPUREG — reference note (820-01949)

  • From its name, this is a 5 V rail in the G3S (always-on) group, feeding the CPU regulator section; the name suggests it is present whenever the board has standby power.
  • Known-good: diode-to-ground 0.426 in the readings archive. That is a community figure and varies with board state; no known-good voltage is recorded here.
  • To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage at the rail.
  • A diode reading far below 0.426 usually points to a short or a leaky load on the rail; far above it can mean an open trace or missing part. Confirm with a second measurement before replacing anything.
PP5V_G3S_DFR_FILT0.429––
AI: what PP5V_G3S_DFR_FILT is and how to check it

PP5V_G3S_DFR_FILT — 820-01949

  • What it is: from the name, a 5 V rail in the G3S (always-on) group, with "DFR" and "FILT" suggesting it feeds a display/filter section. The archive lists it as a G3H always-on startup stage, so it should be present whenever the board has power.
  • Known-good reading: diode 0.429 to ground, from the readings archive (community contribution, so a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a much higher one to an open trace or missing part. Confirm with a voltage check before replacing anything.
PP5V_G3S_KBD0.4275.000–
AI: what PP5V_G3S_KBD is and how to check it

PP5V_G3S_KBD is a 5 V rail; the G3S part of the name indicates it is an always-on (G3H) supply, and KBD suggests it feeds the keyboard side. The archive lists a known-good diode reading of 0.427 and a voltage of 5.000, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 5.000 V points to the rail being loaded or not being enabled; a diode reading far from 0.427 suggests a short or an open on that net. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP5V_G3S_TPAD0.433––
AI: what PP5V_G3S_TPAD is and how to check it

PP5V_G3S_TPAD is a 5 V rail for the trackpad, from the name: G3S is an always-on (G3H) rail, so it should be present whenever the board has standby power. The only known-good reading here is a diode value of 0.433 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.433 suggests a short or leaky part on the rail; a much higher or open reading points to a broken connection. A missing voltage with a normal diode reading points upstream, to whatever feeds the rail.

PP5V_G3S_TPAD_CONN0.424––
AI: what PP5V_G3S_TPAD_CONN is and how to check it

PP5V_G3S_TPAD_CONN is a 5 V rail feeding the trackpad connector; the G3S suffix in its name indicates it's an always-on (G3H) supply, so it should be present whenever the board has power. The only known-good reading in the archive is a diode value of 0.424 to ground, with no condition noted and no known-good voltage recorded here.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.424.
  • Then power the board and measure the voltage on the rail; no known-good voltage is available for comparison, so judge it against what the trackpad connector expects.
  • A diode reading far below 0.424 suggests a short or a leaky part on that rail; a much higher or open reading suggests a broken trace or missing connection.
PPBUS_G3H0.51013.100–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this board; the "G3H" suffix, from the name, marks it as an always-on rail. The archive lists a diode reading of 0.510 and a voltage of 13.100 for it, but no condition is recorded, so treat these as a guide only. To check it, power the board off and measure diode mode from PPBUS_G3H to ground, then apply power and measure the voltage on the rail. A diode reading well below 0.510 suggests a short or leaky part on the bus, while a voltage far from 13.100 with power applied points to a charging or power-supply fault upstream. No known-good resistance reading exists here, so compare against a matching net or a known-good board if needed.

PPBUS_G3H_SPKRAMP_LEFT0.51012.000–
AI: what PPBUS_G3H_SPKRAMP_LEFT is and how to check it

PPBUS_G3H_SPKRAMP_LEFT is, from its name, the always-on G3H main bus feeding the left speaker amplifier on this 820-01949. The archive lists a known-good diode reading of 0.510 and a voltage of 12.000 V; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.510 suggests a short or leaky component on that rail; a missing or low voltage points to the supply feeding it rather than the amp itself. No known-good resistance reading is available here, so compare against a matching net or a known-good board.

PPBUS_G3H_SSD00.51013.100–
AI: what PPBUS_G3H_SSD0 is and how to check it

PPBUS_G3H_SSD0 is the always-on G3H main bus rail feeding the SSD section, judged from the name. The archive lists a known-good diode reading of 0.510 and a voltage of 13.100, with no condition noted. With the board unpowered, measure diode mode from the rail to ground; then power up and check the voltage. A diode reading far below 0.510 usually points to a short or a failing part on that rail, while a missing or low voltage points to the rail not coming up. No known-good resistance reading here, so compare against a matching net or a known-good board.

PPDCIN_G3H0.55020.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on DC input rail, from the G3H suffix meaning it should be present whenever the charger is connected. The archive lists a diode reading of 0.550 and a voltage of 20.000 for this rail; treat these as a guide, not a spec. With the board unpowered, measure diode mode from PPDCIN_G3H to ground and compare with 0.550; then apply power and check for about 20 V. A diode reading far below 0.550 suggests a short or leaky part on the rail, while a missing or low voltage with a normal diode reading points upstream to the charger input path. No known-good resistance reading is recorded here.

PPDCIN_G3H_CHGR0.56220.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the always-on DC input rail feeding the charger section; the G3H part of the name indicates it should be present whenever power is connected. The archive lists a known-good diode reading of 0.562 and a voltage of 20.000 V, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 20 V points to a problem upstream at the input or adapter side rather than on this rail itself; a diode reading far from 0.562 suggests a short or leaky component on the rail. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPHV_INT_G3H_R0.55020.000–
AI: what PPHV_INT_G3H_R is and how to check it
  • What it is: From its name, PPHV_INT_G3H_R is a high-voltage internal rail that is always on (the G3H suffix means always-on). The board data doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.550 to ground, and 20.000 V with power applied. No known-good resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.550 suggests a short or leaky part on the rail; a missing or low voltage points to the supply feeding it. Confirm with a second measurement before replacing anything.
PPHV_INT_G3H_T0.55020.000–
AI: what PPHV_INT_G3H_T is and how to check it

PPHV_INT_G3H_T is an always-on rail, judging from the G3H part of its name (general naming convention, not from board data). The archive lists a known-good diode reading of 0.550 and a voltage of 20.000, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.550 usually points to a short or a leaky part on that rail; far above it suggests an open path. There is no known-good resistance reading here, so compare against a matching net or a known-good board if you need one.

PPHV_INT_G3H_W0.54920.000–
AI: what PPHV_INT_G3H_W is and how to check it

PPHV_INT_G3H_W is an always-on rail, judged from the G3H in its name (general naming convention, not board data). The archive lists a diode reading of 0.549 and a voltage of 20.000 for it, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading well below 0.549 suggests a short or leaky load on the rail; a voltage far from 20.000 points to a supply or load fault upstream. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PPHV_INT_G3H_X0.55020.000–
AI: what PPHV_INT_G3H_X is and how to check it

PPHV_INT_G3H_X is an always-on rail, judged from the G3H part of its name; the PPHV prefix suggests a high-voltage supply, but that's general naming, not from this board's data. The archive lists a known-good diode reading of 0.550 and a voltage of 20.000, with no condition noted. Check it with the board unpowered in diode mode from the net to ground, then power up and measure the voltage. A diode reading far from 0.550 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a bad part. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPVBAT_G3H_CHGR_R0.51013.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — reference note

  • From its name this is a battery/charger rail that is always on (G3H), tied to the charger side of the battery path. It is not a switched rail.
  • Known-good readings in the archive: diode 0.510 to ground, and 13.100 V with power applied. These are community figures and a guide only, not a guaranteed value for every board state.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode reading well below 0.510 suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken path. A voltage far from 13.100 V points to the charger or battery path not coming up. No known-good resistance reading is available for this rail.
PPVBAT_G3H_CHGR_REG0.51013.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side battery rail; the "G3H" part of the name indicates it is always-on. In the readings archive its known-good values are a diode reading of 0.510 and a voltage of 13.100 (community readings, so treat them as a guide; no condition is recorded). Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.510 suggests a short or leaky part on the rail; a voltage well off 13.100 points to the charger or battery supply side. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PPVBAT_G3H_CONN1.574––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judging by the name (G3H = always on, CONN = connector). The archive has one known-good diode reading for it: 1.574, with no condition noted. Check it in diode mode to ground with the board unpowered, then measure the voltage with power applied; no known-good voltage reading here. A diode reading far below 1.574 usually points to a short or a leaky part on that net, but one reading isn't proof, so compare with a matching net or a known-good board before replacing anything.

PPVIN_G3H_P3V3G3H0.51013.100–
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H is an always-on (G3H, from the name) input rail on the 820-01949. The archive lists a known-good diode reading of 0.510 and a voltage of 13.100; no condition is recorded for either, so treat them as a guide only.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.510.
  • Then power the board and measure the voltage, expecting around 13.100.
  • A diode reading far below 0.510 suggests a short or a leaky part on the rail; a voltage well off 13.100 points to a supply or enable problem upstream.

There is no known-good resistance reading for this rail, so compare against a matching net or a known-good board if needed.

PPVIN_G3H_P3V3G3HRTC0.510––
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC is an input rail that feeds the P3V3G3HRTC rail; the G3H in the name indicates it is always-on, and this is from the name rather than from a board file. The archive lists one known-good reading: diode mode to ground 0.510, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching net or a known-good board. A diode reading far below 0.510 usually points to a short or a leaky load on the rail; a far higher or open reading points to a broken connection, but one reading alone does not confirm a bad part.

PPVIN_G3H_P3V3G3HRTC_R0.51712.000–
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it

PPVIN_G3H_P3V3G3HRTC_R is an always-on input rail, going by the G3H in its name; it's the feed into the P3V3G3H RTC regulator section. In the readings archive its known-good values are diode 0.517 and voltage 12.000, with no condition recorded, so treat them as a guide only.

  • Check it unpowered in diode mode from the net to ground; 0.517 is the archived reference.
  • Then power the board and measure the voltage; 12.000 is the archived reference.
  • A diode reading well below 0.517 usually suggests a short or a leaky part on the rail; a much higher one can mean an open path. A voltage far off 12.000 points to a supply or upstream fault.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board.

These are community readings and vary with board state, so confirm with a second measurement before replacing anything.

PPVIN_G3H_P5VG3S0.51013.100–

S5 and SUS: standby 6

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V8_S50.2701.800–
AI: what PP1V8_S5 is and how to check it

PP1V8_S5 is a 1.8 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, though that's from the name rather than confirmed circuit data. The archive lists a known-good diode reading of 0.270 and a voltage of 1.800 for this rail. To check it, power the board off and measure diode mode from PP1V8_S5 to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.270 usually points to a short or a faulty component on that net, while a missing or wrong voltage points to the standby supply not coming up. No known-good resistance reading is available here, so compare against a matching net or a known-good board if needed.

PP1V8_S5_THMSNSA_R0.291––
AI: what PP1V8_S5_THMSNSA_R is and how to check it

PP1V8_S5_THMSNSA_R is a 1.8 V standby rail, judged from its name: PP1V8 for the voltage, S5 for standby state, and THMSNSA likely a thermal-sensor feed. The only known-good figure here is a diode reading of 0.291 to ground; no known-good voltage reading is recorded.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.291.
  • Then power the board and measure the rail voltage; expect about 1.8 V from the name, but that is general, not a recorded value.
  • A diode reading far below 0.291 suggests a short or leaky part on the rail; far above suggests an open path. Either way, confirm with a second measurement before replacing anything.
PP1V8_S5_THMSNSB_R0.290––
AI: what PP1V8_S5_THMSNSB_R is and how to check it
  • What it is: From the name, PP1V8_S5_THMSNSB_R is a 1.8 V standby rail (S5/SUS stage) tied to thermal sensing (THMSNS). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.290 to ground, with no condition noted. No known-good voltage or resistance reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.290; then power up and measure the voltage, expecting about 1.8 V from the name.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing voltage points upstream to the standby supply or enable. Confirm with a second measurement before replacing anything.
PP1V24_S5_PCH_VCCDPHY0.369––
AI: what PP1V24_S5_PCH_VCCDPHY is and how to check it

PP1V24_S5_PCH_VCCDPHY — reference note

  • From its name, this is a 1.24 V rail (PP1V24) in the S5 standby domain, feeding the PCH's display PHY supply (VCCDPHY). The S5/SUS tag puts it in the always-on standby stage, so it should be present before the board fully powers up.
  • Known-good reading in the archive: diode mode to ground 0.369. That's a community value and varies with board state, so treat it as a guide only. No known-good voltage reading is recorded here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage at the rail.
  • A diode reading far below 0.369 usually points to a short or a leaky load on the rail; far above it can mean an open trace or missing part. Confirm with a voltage check before replacing anything.
PP3V3_S50.3563.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the "S5" in the name marks it as a standby rail, present before the board fully powers on.

  • Known-good readings here: diode 0.356 to ground, voltage 3.300. These come from community readings and are a guide only; no condition is recorded.
  • Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure the voltage.
  • A voltage far below 3.300 with power on points to the rail not coming up or being loaded down; a diode reading far from 0.356 suggests a short or open on that net.
  • No known-good resistance reading is recorded for this rail.
PP5V_S5_LDO0.494––
AI: what PP5V_S5_LDO is and how to check it

PP5V_S5_LDO is a 5V standby rail, judged from its name (S5/SUS = standby), so it should be present before the board fully powers on. The only known-good reading here is a diode value of 0.494 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then apply power and measure the voltage at the rail. A diode reading far below 0.494 suggests a short or leaky load on the rail; a far higher or open reading points to a broken path or missing source. A missing or low voltage with a normal diode reading points upstream, at the standby supply that should generate it.

S4 9

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP0V9_SSD0_S4E0_VDD_PLL0.307––
AI: what PP0V9_SSD0_S4E0_VDD_PLL is and how to check it

PP0V9_SSD0_S4E0_VDD_PLL is a 0.9 V rail feeding the SSD's PLL supply, and the S4 in its name marks it as a startup-stage rail (both from the name). The archive lists one known-good diode reading, 0.307, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage is near 0.9 V. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.307 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP0V9_SSD0_S4E1_VDD_PLL0.295––
AI: what PP0V9_SSD0_S4E1_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail feeding the SSD's PLL supply, in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good: diode reading 0.295 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 0.9 V.
  • If far off: a low diode reading usually points to a shorted load on the rail; a high or open one to a missing feed. Confirm with a second measurement before replacing anything.
PP0V9_SSD0_S4E2_VDD_PLL0.312––
AI: what PP0V9_SSD0_S4E2_VDD_PLL is and how to check it

PP0V9_SSD0_S4E2_VDD_PLL — reference note

  • From its name, this is a 0.9 V rail feeding the SSD's PLL supply, in the S4 startup stage. The board data has no board file, so the parts on the net aren't known.
  • Known-good reading: diode 0.312 in diode mode. That is a community guide, not a factory spec, and it varies with board state. No known-good voltage reading here.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • A diode reading far from 0.312 usually points to a shorted or leaky part on the rail or its load, not proof of one. Confirm with voltage and, if needed, compare against a matching rail on a known-good board before replacing anything.
PP0V9_SSD0_S4E3_VDD_PLL0.301––
AI: what PP0V9_SSD0_S4E3_VDD_PLL is and how to check it

PP0V9_SSD0_S4E3_VDD_PLL — the name indicates a 0.9 V rail feeding the SSD's PLL supply, in the S4 startup stage (from the name only; the parts on it aren't documented here).

  • Known-good: diode 0.301 to ground, no condition noted. No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 0.9 V.
  • A diode reading far from 0.301 suggests a short or leaky part on the rail; a correct diode reading with no voltage points to the supply that generates it or its enable.
PP1V8_S4SW_SNS0.492––
AI: what PP1V8_S4SW_SNS is and how to check it

PP1V8_S4SW_SNS is a 1.8 V rail, from its name: the "S4" part marks it as a startup-stage rail, and "SNS" suggests a sense line. The only known-good reading here is a diode value of 0.492 to ground; no known-good voltage is listed. Check it with the board unpowered in diode mode, red probe on ground, then measure the voltage with power applied. A diode reading far from 0.492 usually points to a short or a leaky part on that rail, but one reading isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP5V_S4_WLAN_ISNS_DOL––
AI: what PP5V_S4_WLAN_ISNS_D is and how to check it
  • What it is: From its name, PP5V_S4_WLAN_ISNS_D is a 5 V WLAN rail that comes up at the S4 startup stage; the ISNS suffix suggests a current-sense line (general naming, not confirmed for this board).
  • Known-good reading: The archive lists diode mode to ground as OL. No voltage or resistance reading is recorded here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. With power applied, measure the voltage on the net and compare it with the S4 stage timing.
  • If it's far off: A short or low diode reading points to a fault on that rail or its load; OL with no voltage at S4 points upstream to the enable or supply for the rail. Confirm with a second measurement before replacing anything.
PP5V_S4_WR_USBC0.5115.000–
AI: what PP5V_S4_WR_USBC is and how to check it

PP5V_S4_WR_USBC is a 5 V rail in the S4 startup stage, judging from its name, and the WR_USBC part suggests it feeds the USB-C side. Known-good readings in the archive: diode 0.511 and voltage 5.000, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.511 usually points to a short or a leaky part on that rail; a missing 5.000 V points upstream in the S4 enable or supply. No known-good resistance reading here, so compare against a matching rail or a known-good board.

PP5V_S4_XT_USBC0.4915.000–
AI: what PP5V_S4_XT_USBC is and how to check it

PP5V_S4_XT_USBC is a 5 V rail; the "S4" in the name marks it as a startup-stage rail, and "USBC" suggests it serves the USB-C side (that part is from the name, not confirmed by board data). Known-good readings in the archive: diode 0.491 and voltage 5.000, with no condition recorded — treat these as a guide only. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.491 usually points to a short or leaky part on the rail; a voltage well under 5.000 suggests the rail isn't being enabled or is loaded down. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.

PP5V_S4SW_ISNSOL––
AI: what PP5V_S4SW_ISNS is and how to check it

PP5V_S4SW_ISNS — from the name, a 5 V switch rail in the S4 startup stage, with ISNS indicating a current-sense line. The only archived reading is a diode value of OL to ground, with no condition recorded; there is no known-good voltage or resistance reading here. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S4. A reading far from the archived OL usually points to a short or a leaky component on that rail, but one reading isn't proof — compare against a matching net or a known-good board before replacing anything.

S3: memory 7

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S30.2000.600–
AI: what PP0V6_S3 is and how to check it

PP0V6_S3 is a 0.6 V rail, and the S3 suffix in its name points to the memory stage of the startup sequence (from the name; general convention, not confirmed for this board).

  • Known-good readings here: diode 0.200 to ground, voltage 0.600. No condition is recorded with them, so treat them as a guide.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.200 suggests a short or a low-impedance load on the rail; a voltage far off 0.600 points to the rail not coming up or being loaded down.
  • No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP0V6_S3_REG_R0.200––
AI: what PP0V6_S3_REG_R is and how to check it

PP0V6_S3_REG_R is a 0.6 V rail; the "S3" in the name suggests it belongs to the memory (S3) startup stage, and "REG" suggests a regulated supply — both from the name, not from board data.

  • Known-good: diode 0.200 to ground (community reading, a guide; board state affects it). No known-good voltage reading here.
  • Check: power off and unplugged, diode mode from the rail to ground; then power on and measure the voltage.
  • A diode reading far from 0.200 usually points to a short or leaky part on that rail, but one reading isn't proof — compare with a matching rail or a known-good board before replacing anything.
PP1V1_S30.0441.100–
AI: what PP1V1_S3 is and how to check it

PP1V1_S3 is a 1.1 V supply rail; the "S3" in the name marks it as a memory-stage rail (from the name, not from a schematic). The archived reading for this board is diode 0.044 and voltage 1.100, with no condition recorded, so treat those as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode value far from 0.044 suggests a short or leaky part on the rail; a voltage well off 1.100 points to the rail not coming up or being loaded down. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PP1V1_S3_CPU0.158––
AI: what PP1V1_S3_CPU is and how to check it

PP1V1_S3_CPU is a 1.1 V rail in the S3 (memory) startup stage, judging from its name; the archive has no board file, so the parts on it aren't known. The only known-good reading here is diode 0.158, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.158 usually points to a short or leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP1V1_S3_REG_R0.0441.100–
AI: what PP1V1_S3_REG_R is and how to check it

PP1V1_S3_REG_R is a 1.1 V rail; the "S3" in the name marks it as a memory-stage supply, and "REG" suggests it comes from a regulator (that part is from the name, not from board data).

  • Known-good readings from the archive: diode 0.044 to ground, voltage 1.100 V. These are community values and vary with board state, so treat them as a guide.
  • To check: power off and unplug, then diode-mode from the rail to ground; if that looks normal, power up and measure the voltage.
  • A diode reading far below 0.044 suggests a short or a leaky load on the rail; a voltage well off 1.100 V points at the regulator or its feedback. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before replacing anything.
PP1V8_S30.279––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix in its name points to the memory stage of startup. The archive lists one known-good diode reading of 0.279 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on the rail and black on ground, then measure the voltage with power applied. A diode reading far from 0.279 usually points to a short or a leaky part on that rail, but a single reading isn't proof a part is bad. There is no known-good voltage reading here, so compare against a matching rail or a known-good board.

PP1V8_S3_MEM0.279––
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM is a 1.8 V rail; the S3 suffix in its name marks it as a memory rail in the S3 startup stage. The only known-good figure here is a diode reading of 0.279 to ground, with no condition recorded; there is no known-good voltage reading in this data. To check it, power the board off and measure diode mode from PP1V8_S3_MEM to ground, then apply power and measure the voltage. A diode reading far from 0.279 usually points to a short or a damaged part on that rail, but one reading isn't proof, so confirm with a voltage check before replacing anything.

S0: running 36

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V1_S0SW0.467––
AI: what PP1V1_S0SW is and how to check it

PP1V1_S0SW is a 1.1 V rail; the "S0" in its name marks it as a running-state rail (from the name), so it should be present once the board is fully on, not in standby.

  • Known-good reading in the archive: diode mode to ground 0.467 (board unpowered). No known-good voltage reading is recorded here.
  • To check: power off, measure diode mode from the rail to ground and compare with 0.467. Then power on and measure the voltage at the rail; it should sit near 1.1 V, but there is no archived voltage value to compare against.
  • A diode reading far below 0.467 suggests a short or a failing load on the rail; far above suggests an open path. A missing or low voltage with power applied points to the rail's supply or enable, not necessarily the load.

These readings are community-contributed guides and vary with board state, so confirm against a matching rail or a known-good board before replacing anything.

PP1V05_S0_CPU_VCCPLL0.193––
AI: what PP1V05_S0_CPU_VCCPLL is and how to check it

PP1V05_S0_CPU_VCCPLL is a 1.05 V rail feeding the CPU's PLL supply, and the S0 in its name indicates it belongs to the running (S0) power state. The only known-good reading here is a diode value of 0.193 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.193 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a known-good board before replacing anything.

PP1V05_S0_CPU_VCCST0.1131.000–
AI: what PP1V05_S0_CPU_VCCST is and how to check it

PP1V05_S0_CPU_VCCST is a 1.05 V rail feeding the CPU's VCCST supply; the "S0" in the name indicates it belongs to the running (S0) power state, and this is from the name rather than a schematic. Known-good readings in the archive: diode 0.113 to ground and 1.000 V with the board powered. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.113 usually points to a short or leaky load on the rail, while a voltage well off 1.000 V suggests the rail isn't regulating or is loaded down; no known-good resistance reading is recorded here.

PP1V05_S0SW_VCCSTG0.125––
AI: what PP1V05_S0SW_VCCSTG is and how to check it
  • What it is: PP1V05_S0SW_VCCSTG is a 1.05 V rail, and the S0 in its name marks it as a running-state supply (from the name). VCCSTG suggests a storage-related rail, but that's general interpretation, not from this board's data.
  • Known-good reading: diode 0.125 in the readings archive, with no condition noted. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a diode reading well below known-good usually points to a short or a failing part on the rail, while a missing voltage with a normal diode reading points upstream to its supply or enable. Treat these as likely causes, not confirmed ones.
PP1V8_S0SW0.369––
AI: what PP1V8_S0SW is and how to check it

PP1V8_S0SW is a 1.8 V rail that, from its name, is a switched supply active in the S0 (running) state. The only known-good reading here is a diode value of 0.369 to ground; there is no known-good voltage reading in this data.

  • Check it with the board unpowered: diode mode from PP1V8_S0SW to ground, expecting around 0.369.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a known-good board or the rail's nominal 1.8 V.
  • A diode reading far below 0.369 usually points to a short or a failed part on the rail; a much higher or open reading can mean a broken connection. These are general guidelines, not confirmed causes.
PP3V3_S0_TBT_WR_ISNS_R0.370––
AI: what PP3V3_S0_TBT_WR_ISNS_R is and how to check it
  • What it is: From the name, PP3V3_S0_TBT_WR_ISNS_R is a 3.3 V rail (PP3V3) that is on in the S0 running state and is a Thunderbolt write current-sense line (TBT_WR_ISNS). The name is the only source for this; the parts on the net aren't known.
  • Known-good reading: Diode mode to ground is 0.370, from the community archive. That's a guide, not a spec, and there's no known-good voltage reading here.
  • How to check: Power off and confirm the rail is discharged, then measure diode mode from the rail to ground. Then power up and measure the voltage at the rail.
  • If it's far off: A diode reading well below 0.370 suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken connection. A wrong voltage with a normal diode reading points to the supply or enable side rather than a short.
PP3V3_S0_TBT_XT_ISNS_R0.450––
AI: what PP3V3_S0_TBT_XT_ISNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail tied to Thunderbolt current sensing (ISNS). The exact parts on it aren't documented here.
  • Known-good reading: diode 0.450 to ground. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a much lower diode reading usually points to a short or leaky part on that net; a much higher one to an open. Treat one reading as a guide, not proof a part is bad.
PP3V3_S0SW_LCD0.492––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a switched 3.3 V rail feeding the LCD, from its name: the S0 state means it's present while the board is running, and SW indicates it's switched on by a control signal. The only known-good reading here is a diode value of 0.492 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.492 suggests a short or leaky load on the rail; a much higher or open reading points to a broken connection or missing feed. Voltage absent while the board is running points upstream to the switch control or its source rail, but this isn't confirmed without tracing those.

PP3V3_S0SW_LCD_R0.492––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is the switched 3.3 V LCD rail; the S0 in the name indicates it belongs to the running state, and SW suggests it is switched on rather than always present. The archive lists a diode reading of 0.492 for this net; no voltage or resistance readings are recorded here.

  • Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the same net.
  • A diode reading far from 0.492 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.
  • No known-good voltage is recorded for this rail, so compare against a known-good board of the same model.
PP3V3_TBT_R_S00.517––
AI: what PP3V3_TBT_R_S0 is and how to check it

PP3V3_TBT_R_S0 is a 3.3 V rail; from the name it's a Thunderbolt-related supply that is on in the S0 (running) state. The only known-good reading here is a diode value of 0.517 to ground, with no condition noted, and there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red lead on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.517 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_TBT_S0_SVR_R0.517––
AI: what PP3V3_TBT_S0_SVR_R is and how to check it

PP3V3_TBT_S0_SVR_R is a 3.3 V rail; from its name it's a Thunderbolt (TBT) supply that runs in the S0 (running) state, and SVR suggests a standby/always-on regulator source. The archive lists one known-good diode reading of 0.517 to ground on this net; there's no known-good voltage reading here. Check it unpowered in diode mode to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.517 usually points to a short or a damaged component on that net, but confirm with a voltage check before replacing anything.

PP3V3_TBT_S0_SVR_T0.523––
AI: what PP3V3_TBT_S0_SVR_T is and how to check it

PP3V3_TBT_S0_SVR_T — reference note

  • What it is: from the name, a 3.3 V rail (PP3V3) for the Thunderbolt section (TBT), active in the running state (S0), likely a "server"/always-on variant (SVR). The exact loads on it aren't documented here.
  • Known-good reading: diode-to-ground 0.523 in the archive. This is a community value and a guide only; no known-good voltage reading is recorded here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.523. Then power up and measure the voltage at the rail; expect about 3.3 V, though no archived voltage confirms it.
  • If it's far off: a much lower diode reading suggests a short or a failed load on the rail; a much higher one suggests an open trace or missing part. Confirm with a second measurement before replacing anything.
PP3V3_TBT_S0_SVR_W0.517––
AI: what PP3V3_TBT_S0_SVR_W is and how to check it

PP3V3_TBT_S0_SVR_W is a 3.3 V rail; from the name it's a Thunderbolt-related supply that comes up in S0 (running) state. The archive lists one known-good reading: diode 0.517, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage reading is recorded here. A diode reading far from 0.517 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_TBT_S0_SVR_X0.523––
AI: what PP3V3_TBT_S0_SVR_X is and how to check it

PP3V3_TBT_S0_SVR_X is a 3.3 V rail for the Thunderbolt (TBT) section, in the S0 running state, based on its name. The archive lists one known-good diode reading of 0.523 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.523 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP3V3_TBT_T_S00.523––
AI: what PP3V3_TBT_T_S0 is and how to check it

PP3V3_TBT_T_S0 is a 3.3 V S0 (running-state) rail, most likely the Thunderbolt supply, judging from the name. The archive lists one known-good diode reading of 0.523 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S0. A diode reading far from 0.523 usually points to a short or a leaky part on that rail, but a single reading doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_TBT_T_S0_R_SWR0.517––
AI: what PP3V3_TBT_T_S0_R_SWR is and how to check it
  • PP3V3_TBT_T_S0_R_SWR is a 3.3 V rail, from its name: the TBT (Thunderbolt) side, S0 (running state), switched rail. The exact parts on it aren't known here.
  • Known-good: diode-to-ground 0.517 (community reading, a guide only). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe to ground, red to the rail. Then power up and measure the voltage.
  • A diode reading far below 0.517 suggests a short or leaky part on the rail; far above can mean an open path. Confirm with voltage before replacing anything.
PP3V3_TBT_T_S0_R_SXT0.523––
AI: what PP3V3_TBT_T_S0_R_SXT is and how to check it

PP3V3_TBT_T_S0_R_SXT is a 3.3 V rail, from its name: the "3V3" is the voltage, "TBT" points to the Thunderbolt side, and "S0" means it belongs to the running (S0) power state. The only known-good reading here is a diode value of 0.523, with no condition noted; there is no known-good voltage or resistance reading for this rail.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.523.
  • Then power the board and measure the voltage on the rail; it should sit near 3.3 V once the board is in S0.

A diode reading far below 0.523 usually suggests a short or a leaky part on the rail, while a much higher one can mean an open connection. A missing or low voltage with a normal diode reading points more toward the rail not being enabled or its supply upstream, not a shorted load. These are general guidelines, not confirmed causes for this board.

PP3V3_TBT_W_S00.517––
AI: what PP3V3_TBT_W_S0 is and how to check it

PP3V3_TBT_W_S0 is a 3.3 V rail for the Thunderbolt section, from its name, and the S0 suffix indicates it is present in the running state. The archive lists one known-good diode reading of 0.517 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, then measure the voltage with the board powered and running. A diode reading far from 0.517 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a known-good board before replacing anything.

PP3V3_TBT_X_S00.523––
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt section, and the S0 suffix in its name means it's present in the running state. The only known-good reading here is a diode value of 0.523 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. No known-good voltage reading is listed here, so compare against a matching rail or a known-good board. A diode reading far below 0.523 usually points to a short or a failing load on the rail, but confirm with a second measurement before replacing anything.

PP3V3_TBT_X_S0_R_SWR0.517––
AI: what PP3V3_TBT_X_S0_R_SWR is and how to check it

PP3V3_TBT_X_S0_R_SWR is a 3.3 V rail, from its name: a Thunderbolt-related supply that is present in the S0 (running) state. The only known-good figure here is a diode reading of 0.517 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.517.
  • Then power the board and measure the voltage on the rail; it should come up when the board reaches S0.

A diode reading far below 0.517 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken connection. A missing voltage with a normal diode reading points more to the enable or supply side than to the rail itself. These are general guidelines, not confirmed causes for this board.

PP3V3_TBT_X_S0_R_SXT0.523––
AI: what PP3V3_TBT_X_S0_R_SXT is and how to check it
  • What it is: From its name, PP3V3_TBT_X_S0_R_SXT is a 3.3 V rail for the Thunderbolt (TBT) section, active in the S0 (running) state. The exact parts on it aren't known here.
  • Known-good reading: diode 0.523 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V in S0.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to its enable or supply. Confirm with a second measurement before replacing anything.
PP5V_S0_BKLT_A0.436––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the backlight rail that runs in the S0 (running) state, judged from the name; the data doesn't list which parts sit on it. The only known-good reading here is diode mode 0.436 to ground, with no condition noted. Check it unpowered in diode mode to ground, then measure the voltage with the board powered in S0; no known-good voltage reading is available here. A diode reading far from 0.436 usually points to a short or leaky component on the rail, but one reading isn't proof — compare against a matching net or a known-good board before replacing anything.

PP5V_S0_BKLT_D0.435––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the 5 V backlight rail that runs in the S0 (on) state, judging by the name. The archive lists one known-good diode reading, 0.435, with no condition noted; there is no known-good voltage reading here. With the board unpowered, measure diode mode from PP5V_S0_BKLT_D to ground and compare with 0.435. Then power up and check the voltage, expecting roughly 5 V from the name. A diode reading far below 0.435 suggests a short or leaky load on the rail; far above suggests an open path. These are guides from community readings, not confirmed values.

PP5V_S0SW_LCD0.576––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is a switched 5 V LCD rail; from the name, S0 means it belongs to the running state and SW that it is switched on by a control signal. The only archived reading is diode mode 0.576, with no condition recorded and no voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage while the display should be on. A diode reading far from 0.576 usually points to a short or a leaky part on the rail, while correct diode but missing voltage points upstream to the switch or its enable. No known-good voltage reading here, so compare against a matching rail or a known-good board.

PP5V_S0SW_LCD_ISNS_R0.576––
AI: what PP5V_S0SW_LCD_ISNS_R is and how to check it

PP5V_S0SW_LCD_ISNS_R is a 5 V S0 (running-state) switched rail tied to the LCD current-sense circuit, judging by its name. The only known-good reading here is a diode value of 0.576; there is no known-good voltage or resistance reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.576 usually points to a short or leaky part on the rail, while a much higher reading can mean an open path; treat these as a guide and confirm with a second measurement before replacing anything.

PPVCCIN_S0_CPU0.0901.50080.000R
AI: what PPVCCIN_S0_CPU is and how to check it

PPVCCIN_S0_CPU is the CPU input supply rail; the S0 in the name indicates it is active in the running state. Archived readings for this rail are a diode value of 0.090, a voltage of 1.500, and a resistance of 80.000R — treat these as a guide only, since they come from community contributions and vary with board state. Check it with the board unpowered in diode mode to ground, then power up and measure the voltage. A reading far from these values usually points to a short or a failed supply component on the rail, but confirm with a second measurement before replacing anything. No known-good value of another kind is listed here.

PPVIN_S0_CPUVR_VIN0.494––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VR (CPU voltage regulator) input rail, active in the S0 running state, based on its name. The only known-good reading here is a diode value of 0.494; no voltage or resistance readings are recorded for this rail.

  • Check with the board unpowered: diode mode, red probe on ground, black probe on the rail. Compare against 0.494.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage here, so compare with the same rail on a known-good board.
  • A diode reading far below 0.494 usually points to a short or a leaky part on the rail; a much higher reading can mean an open connection. A single reading isn't proof a part is bad, so confirm with a voltage check before replacing anything.
PPVIN_S0_PRIM1V80.51013.100–
AI: what PPVIN_S0_PRIM1V8 is and how to check it
  • What it is: From the name, PPVIN_S0_PRIM1V8 is the primary 1.8 V input rail, active in the S0 (running) state.
  • Known-good readings (community archive, a guide only): diode 0.510 to ground, voltage 13.100. No other known-good values of a different kind are listed here.
  • How to check: Power off and unplugged, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: A much lower diode reading suggests a short or leaky part on the rail; a missing or wrong voltage points to the supply feeding it or an enable condition. The archive has no part-level data for this net, so confirm against a known-good board before replacing anything.
PPVIN_S0PRIM_1V8_RC0.488––
AI: what PPVIN_S0PRIM_1V8_RC is and how to check it
  • What it is: From the name, a 1.8 V primary input rail active in the S0 (running) state. "PP" usually marks a power rail, and "RC" suggests a filtered or RC-smoothed feed. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.488 to ground, from the readings archive. That's a community guide, not a factory spec, and it varies with board state.
  • How to check: With the board powered off, measure diode mode from the rail to ground and compare with 0.488. Then power up and measure the DC voltage, which should sit near 1.8 V.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a much higher one to an open feed. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board before replacing anything.
PPVIN_S0SW_LCDBKLT0.91012.900–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the LCD backlight input rail; the S0SW part of the name indicates it is switched in the running (S0) state. Known-good readings here are a diode value of 0.910 and 12.900 V with power applied. Check it by measuring diode mode from the rail to ground with the board unpowered, then measure the voltage with the board powered and the display connected. A diode reading far below 0.910 suggests a short or leaky component on the rail; a voltage well under 12.900 V points to the backlight supply or its enable not coming up. No known-good resistance reading is available for this rail.

PPVIN_S0SW_LCDBKLT_F0.510––
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT_F is the switched input supply feeding the LCD backlight circuit, active in the S0 (running) state. The exact parts on this net aren't documented here.
  • Known-good reading: diode 0.510 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the net to ground and compare with 0.510; then power up and measure the voltage present.
  • If it's far off: a much lower diode reading usually points to a short or leaky component on the rail; a much higher one to an open path. Confirm with a voltage check before replacing anything.
PPVIN_S0SW_LCDBKLT_R0.510––
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail; the name marks it as an S0 (running-state) switch rail feeding the LCD backlight, and that reading is from the name rather than from a schematic.

  • Known-good: diode 0.510 to ground (no condition recorded). No known-good voltage or resistance reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • A diode reading far from 0.510 usually points to a short or leaky component on the rail, but confirm with a second reading before replacing anything.
PPVOUT_S0_KBDLED0.653––
AI: what PPVOUT_S0_KBDLED is and how to check it

PPVOUT_S0_KBDLED is the keyboard backlight power rail, going by its name (KBDLED = keyboard LED, S0 = running state). The only known-good reading here is diode mode 0.653, with no condition noted; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered: diode mode from the rail to ground, red probe on ground. A far lower reading than 0.653 suggests a short or a leaky part on the rail; a much higher or open reading suggests a break in the feed.
  • Then power the board and measure the voltage on the rail. No known-good voltage is listed, so compare against a known-good board or the rail's expected level.

A reading far from known-good points to a fault on the rail itself, but one reading isn't proof — confirm with a second measurement before replacing anything.

PPVOUT_S0_KBDLED_R0.62240.000–
AI: what PPVOUT_S0_KBDLED_R is and how to check it

PPVOUT_S0_KBDLED_R is a keyboard backlight power rail; the name suggests a switched S0 (running-state) output feeding the keyboard LED circuit, and the 40 V reading fits a boost rail for an LED string. Known-good from the archive: diode 0.622 to ground, and 40.000 V with power applied. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading well below 0.622 suggests a short or leaky load on the rail; a much higher one suggests an open path. No known-good resistance reading exists here, so compare against a matching rail on a known-good board if needed.

PPVOUT_S0_LCDBKLT1.260––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "LCDBKLT" points to the display backlight boost output. The only known-good reading in the archive is a diode value of 1.260 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the DC voltage there. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far from 1.260 usually points to a short or leaky component on the backlight output, but one reading alone doesn't confirm a fault.

PPVOUT_S0_LCDBKLT_F1.26046.000–
AI: what PPVOUT_S0_LCDBKLT_F is and how to check it

PPVOUT_S0_LCDBKLT_F — 820-01949

  • From the name: a display backlight output rail (LCDBKLT), enabled in the S0 running state. It's the boost output feeding the backlight, so it typically sits well above the main rails.
  • Known-good from the readings archive: diode 1.260 to ground, voltage 46.000. These are community readings and a guide only; no condition is recorded.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 1.260. Then power up and measure the voltage, expecting around 46.000 when the backlight is on.
  • A diode reading far below known-good suggests a short or leaky load on the rail; a voltage far off with a normal diode reading points more to the backlight circuit not running or no display attached. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

Every net with a reading

NetDiodeVoltageResistance
1V8_SWCH_EN0.754––
1V8_SWCH_SLEWOL––
ACT_GND0.000––
AGND_P1V8PRIM0.000––
ALL_SYS_PWRGD0.5001.800–
AP_PCIE_WAKE_L0.525––
AUD_CONN_HP_LEFT0.698––
AUD_CONN_HP_RIGHT0.691––
AUD_CONN_HP_SENSE_L1.466––
AUD_CONN_HP_SENSE_R1.467––
AUD_CONN_RING_SENSE0.655––
AUD_CONN_RING20.000––
AUD_CONN_RING2_XW0.648––
AUD_CONN_SLEEVE0.000––
AUD_CONN_SLEEVE_XW0.648––
AUD_CONN_TIP_SENSE1.467––
AUD_DMIC0_DATA_CONN0.586––
AUD_DMIC1_DATA_CONN0.582––
AUD_HP_PORT_CH_GND0.001––
AUD_HP_PORT_L0.698––
AUD_HP_PORT_R0.691––
AUD_HP_PORT_US_GND0.000––
AUD_HP_SENSE_L1.272––
AUD_HP_SENSE_R1.278––
AUD_HS_MIC_N0.632––
AUD_HS_MIC_P0.625––
AUD_PWR_EN0.771––
AUD_RING_SENSE0.634––
AUD_TIP_SENSE1.605––
BKLT_EN_R0.548––
BKLT_ISET_KEYB0.679––
BKLT_KEYB10.662––
BKLT_KEYB20.658––
BKLT_PWM_KEYB_3V30.568––
BKLT_PWM_MLB2TCON0.795––
BKLT_SCL0.558––
BKLT_SD0.602––
BKLT_SDA0.558––
BKLT_SENSE_OUT0.731––
BOARD_REV10.475––
BOARD_REV20.474––
BOOT_CONFIG00.480––
BOOT_CONFIG10.477––
BOOT_CONFIG20.477––
BT_DEV_WAKE0.474––
BT_GPIO_40.705––
BT_HOST_WAKE0.474––
BT_PWR_EN0.485––
BT_ROM_BOOT_HPN_L0.508––
BT_SFLASH_CS_L0.696––
BT_SFLASH_HOLD_L0.460––
BT_SFLASH_WP_L0.455––
BT_SPI2_CLK0.468––
BT_SPI2_CSN0.712––
BT_SPI2_MISO0.458––
BT_SPI2_MOSI0.456––
CAP_PCPU_S0SW0.568––
CAPSLOCK_LED_EN0.556––
CHGR_AMON0.627––
CHGR_AUX_DET0.639––
CHGR_BMON0.626––
CHGR_BOOT10.607––
CHGR_BOOT1_RC0.605––
CHGR_BOOT20.602––
CHGR_BOOT2_RC0.602––
CHGR_COMP0.639––
CHGR_CSI_N0.563––
CHGR_CSI_P0.564––
CHGR_CSI_R_N0.562––
CHGR_CSI_R_P0.562––
CHGR_CSO_N0.510––
CHGR_CSO_P0.509––
CHGR_CSO_R_N0.51013.100–
CHGR_CSO_R_P0.51013.100–
CHGR_EN_MVR0.620––
CHGR_EN_MVR_R0.606––
CHGR_GATE_Q10.822––
CHGR_GATE_Q20.469––
CHGR_GATE_Q30.490––
CHGR_GATE_Q40.804––
CHGR_INT_L0.619––
CHGR_LX10.52813.100–
CHGR_LX20.52813.100–
CHGR_PBUS0.506––
CHGR_RST_IN0.630––
CHGR_RST_IN_R0.677––
CHGR_VBAT0.646––
CODEC_INT_L0.478––
CODEC_RESET_L0.474––
CODEC_WAKE_L0.474––
COMP_A_CPUCORE0.624––
COMP_A_CPUCORE_L2.080––
CORE_ISUMN_R1.940––
CPU_BPM_L<0>0.237––
CPU_BPM_L<1>0.236––
CPU_C10_GATE_L0.511––
CPU_CATERR_L0.135––
CPU_CFG<0>0.229––
CPU_DDR_RCOMP<2>0.100––
CPU_DDR0_ALERT_L0.000––
CPU_DDR1_ALERT_L0.000––
CPU_PECI0.277––
CPU_PROCHOT_L0.444––
CPU_PROCHOT_OUT_L0.458––
CPU_PROCHOT_R_L0.228––
CPU_SMC_THRMTRIP_L0.473––
CPU_VCCSENSE_N0.002––
CPU_VCCSENSE_P0.090––
CPU_VIDALERT_L0.169––
CPU_VIDSCLK0.134––
CPU_VIDSOUT0.135––
CPU_VR_EN0.5861.000–
CPU_VR_EN_R0.585––
CPU_VR_PROCHOT_L0.529––
CPUCORE_FCCM0.596––
CPUCORE_ISEN10.624––
CPUCORE_ISEN20.624––
CPUCORE_ISEN30.626––
CPUCORE_ISNS1_N0.0901.50080.000R
CPUCORE_ISNS1_P0.0901.50080.000R
CPUCORE_ISNS2_N0.0901.50080.000R
CPUCORE_ISNS2_P0.0901.50080.000R
CPUCORE_ISNS3_N0.0901.50080.000R
CPUCORE_ISNS3_P0.0901.50080.000R
CPUCORE_ISUMN0.089––
CPUCORE_ISUMN_R0.484––
CPUCORE_ISUMP0.421––
CPUCORE_PWM10.609––
CPUCORE_PWM20.609––
CPUCORE_PWM30.610––
CPUCORE_SW10.0901.50090.000R
CPUCORE_SW20.0901.50080.000R
CPUCORE_SW30.0901.50080.000R
CPUCORE1_GHOL––
CPUCORE1_GL00.435––
CPUCORE2_GHOL––
CPUCORE2_GL00.440––
CPUCORE3_GL00.438––
CPUTHMSNS_D5_N0.000––
CPUTHMSNS_D5_P0.652––
CPUVASENSE_IN0.384––
CPUVR_PGOOD0.594––
CPUVR_VIDALERT_L_R0.170––
CPUVR_VIDSCLK_R0.134––
CPUVR_VIDSOUT_R0.135––
CPUVRENA0.4653.300–
CPUVRENB0.5091.000–
CPUVSENSE_IN0.089––
DDR_VIEW_00.306––
DDR_VIEW_10.305––
DFR_DISP_INT0.480––
DFR_DISP_RESET_L0.482––
DFR_DISP_TE0.483––
DFR_DISP_VSYNCOL––
DFR_PWR_EN0.480––
DFR_TOUCH_CLK32K_RESET_L0.486––
DFR_TOUCH_INT_L0.481––
DFR_TOUCH_LID_OPEN_LOL––
DFR_TOUCH_RESET_L0.484––
DISP_RCOMP0.141––
DP_INT_HPD2.257––
EADC1_BMON_DISCRETE_ISENSEOL––
EADC1_DDR1V8_ISENSEOL––
EADC1_KBBLT_ISENSEOL––
EADC1_MESA_ISENSEOL––
EADC1_PP1V8_WLANBT_ISENSEOL––
EDP_BKLT_EN0.550––
EDP_INT_AUX_N0.387––
EDP_INT_AUX_P0.372––
EDP_INT_ML_N<0>0.345––
EDP_INT_ML_N<1>0.346––
EDP_INT_ML_N<2>0.345––
EDP_INT_ML_N<3>0.345––
EDP_INT_ML_P<0>0.338––
EDP_INT_ML_P<1>0.337––
EDP_INT_ML_P<2>0.340––
EDP_INT_ML_P<3>0.338––
EDP_PANEL_PWR_BUF_EN0.700––
EDP_PANEL_PWR_DLY_EN0.810––
EDP_PANEL_PWR_EN0.554––
EEPROM_WC_L0.577––
ESPI_CS_L0.457––
ESPI_RESET_L0.461––
FAN_LT_PWM0.788––
FAN_LT_TACHOL––
FAN_RT_PWM0.773––
FAN_RT_TACHOL––
FB_A_CORE_R2.067––
FB_A_CORE_RC1.615––
FB_A_CPUCORE0.609––
FB_CORE0.093––
FB_CORE_R0.090––
FB_CORE_RCOL––
FIVR_PROBE_ANA_00.585––
FIVR_PROBE_ANA_10.585––
FIVR_PROBE_DIG_10.243––
FIVR_VLOAD_CCF0.004––
FIVR_VLOAD_CORE00.002––
FIVR_VLOAD_CORE10.003––
FIVR_VLOAD_CORE30.002––
FIVR_VLOAD_SA0.004––
FIVR_VLOAD_TCSS0.011––
GND0.000––
HS_OTHER3V3_IOUT0.725––
HS_OTHER5V_IOUT0.725––
HW_ID10.494––
I2C_ALS_SCL0.463––
I2C_ALS_SDA0.463––
I2C_BKLT_SCL0.558––
I2C_BKLT_SDA0.554––
I2C_CODEC_SCL0.475––
I2C_CODEC_SDA0.475––
I2C_DFR_SCL0.492––
I2C_DFR_SCL_R0.511––
I2C_DFR_SDA0.492––
I2C_DFR_SDA_R0.511––
I2C_DISP_LS_EN0.495––
I2C_DISP_SCL0.454––
I2C_DISP_SDA0.452––
I2C_FTCAM_ISOL_SCL0.707––
I2C_FTCAM_ISOL_SDA0.717––
I2C_FTCAM_SCL0.440––
I2C_FTCAM_SDA0.444––
I2C_KBD_SCL0.686––
I2C_KBD_SDA0.662––
I2C_PMU_SCL0.476––
I2C_PMU_SDA0.473––
I2C_PWR_SCL0.476––
I2C_PWR_SDA0.476––
I2C_SEP_SCL0.472––
I2C_SEP_SDA0.470––
I2C_SNS_G3S_SCL0.472––
I2C_SNS_G3S_SDA0.472––
I2C_SNS0_S0_SCL0.470––
I2C_SNS0_S0_SDA0.469––
I2C_SNS1_S0_SCL0.472––
I2C_SNS1_S0_SDA0.471––
I2C_SPKRAMP_L_SCL0.383––
I2C_SPKRAMP_L_SDA0.383––
I2C_SPKRAMP_R_SCL0.383––
I2C_SPKRAMP_R_SDA0.382––
I2C_SSD_SCL0.472––
I2C_SSD_SDA0.472––
I2C_TCON_SCL0.500––
I2C_TCON_SDA0.499––
I2C_TPAD_3V3_SCL0.948––
I2C_TPAD_3V3_SCL_R0.919––
I2C_TPAD_3V3_SDA0.960––
I2C_TPAD_3V3_SDA_R0.930––
I2C_TPAD_SDA_R0.504––
I2C_UPC_R_INTM_L0.590––
I2C_UPC_R_SCLM0.551––
I2C_UPC_R_SDAM0.553––
I2C_UPC_SCL0.488––
I2C_UPC_SDA0.491––
I2C_UPC_T_INTM_L0.608––
I2C_UPC_T_SCLM0.567––
I2C_UPC_T_SDAM0.568––
I2C_UPC_W_INTM_L0.595––
I2C_UPC_W_SCLM0.555––
I2C_UPC_W_SDAM0.556––
I2C_UPC_WR_SCL20.485––
I2C_UPC_WR_SDA20.487––
I2C_UPC_X_INTM_L0.598––
I2C_UPC_X_SCLM0.518––
I2C_UPC_X_SDAM0.518––
I2C_UPC_XT_SCL20.509––
I2C_UPC_XT_SDA20.511––
I2S_CODEC_BCLK0.485––
I2S_CODEC_D2R0.472––
I2S_CODEC_LRCLK_R0.490––
I2S_CODEC_R2D0.463––
I2S_CODEC_R2D_R0.460––
I2S_SPKRAMP_L_BCLK0.384––
I2S_SPKRAMP_L_BCLK_R0.404––
I2S_SPKRAMP_L_D2R0.373––
I2S_SPKRAMP_L_D2R_R10.383––
I2S_SPKRAMP_L_D2R_R20.383––
I2S_SPKRAMP_L_LRCLK_R0.381––
I2S_SPKRAMP_L_R2D0.383––
I2S_SPKRAMP_R_BCLK0.384––
I2S_SPKRAMP_R_BCLK_R0.402––
I2S_SPKRAMP_R_D2R0.475––
I2S_SPKRAMP_R_D2R_R10.382––
I2S_SPKRAMP_R_D2R_R20.383––
I2S_SPKRAMP_R_LRCLK0.399––
I2S_SPKRAMP_R_LRCLK_R0.381––
I2S_SPKRAMP_R_R2D0.383––
I2S_SPKRAMP_R_R2D_R0.401––
IMON_A_CPUCORE0.625––
IOXP_I2C_SCL0.665––
IOXP_I2C_SDA0.641––
IOXP1_INT_L0.646––
IOXP1_RESET_L0.744––
IOXP2_ADDR0.719––
IOXP2_INT_L0.645––
IOXP2_RESET_L0.743––
IPD_LID_OPEN0.721––
ISNS_ALSCAM_NOL––
ISNS_ALSCAM_POL––
ISNS_CALPE_NOL––
ISNS_CALPE_POL––
ISNS_CPUDDR_N0.044––
ISNS_CPUDDR_P0.044––
ISNS_CPUVDDQ_NOL––
ISNS_CPUVDDQ_POL––
ISNS_DDR_IOUT0.720––
ISNS_DDRVDDQ_IOUTOL––
ISNS_DDRVDDQ_NOL––
ISNS_DDRVDDQ_POL––
ISNS_DFR3V3_NOL––
ISNS_DFR3V3_POL––
ISNS_DISCHGR_IOUTOL––
ISNS_EADC_NOL––
ISNS_EADC_POL––
ISNS_HS_3V3RTC_NOL––
ISNS_HS_COMPUTING_N0.510––
ISNS_HS_COMPUTING_P0.510––
ISNS_HS_OTHER3V3_N0.510––
ISNS_HS_OTHER3V3_P0.510––
ISNS_HS_OTHER5V_N0.510––
ISNS_HS_OTHER5V_P0.510––
ISNS_KBBLT_NOL––
ISNS_KBBLT_POL––
ISNS_LCDBKLT_N0.510––
ISNS_LCDBKLT_P0.510––
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_MESA_IOUTOL––
ISNS_MESA_NOL––
ISNS_MESA_POL––
ISNS_OCARINA_IOUT0.722––
ISNS_OCARINA_N0.369––
ISNS_OCARINA_P0.369––
ISNS_P1V8_WLANBT_NOL––
ISNS_P1V8_WLANBT_POL––
ISNS_P1V8LPDDR_NOL––
ISNS_P1V8LPDDR_POL––
ISNS_P5VUSBC_WR_IOUT0.718––
ISNS_P5VUSBC_XT_IOUT0.725––
ISNS_PP1V8_S5_NOL––
ISNS_PP1V8_S5_POL––
ISNS_PP3V3_KBD_NOL––
ISNS_PP3V3_KBD_POL––
ISNS_PP3V3_TPAD_NOL––
ISNS_PP3V3_TPAD_POL––
ISNS_PP5V_LCD_NOL––
ISNS_PP5V_LCD_POL––
ISNS_PP5V_TPAD_NOL––
ISNS_PP5V_TPAD_POL––
ISNS_SPKRAMP_LEFT_NOL––
ISNS_SPKRAMP_LEFT_POL––
ISNS_SSDNAND_IOUT0.722––
ISNS_SSDNAND_N0.510––
ISNS_SSDNAND_P0.510––
ISNS_TBT_WR_NOL––
ISNS_TBT_WR_POL––
ISNS_TBT_XT_NOL––
ISNS_TBT_XT_POL––
ISNS_VCCINAUX_IOUTOL––
ISNS_VCCINAUX_N0.3801.800–
ISNS_VCCINAUX_P0.3801.800–
ISNS_WLANBTP3V3_NOL––
ISNS_WLANBTP3V3_POL––
ISUM_COREVR_VCC0.533––
JTAG_ISP_TCK0.515––
JTAG_ISP_TDI0.509––
JTAG_ISP_TDO0.514––
JTAG_TBT_R_TMS0.552––
JTAG_TBT_T_TMS0.608––
JTAG_TBT_W_TMS0.553––
JTAG_TBT_X_TMS0.600––
KBD_CAP_CATHODE0.503––
KBD_CAPSLOCK_LED0.502––
KBD_CONTROL_KEY0.483––
KBD_CONTROL_L0.461––
KBD_DRIVE_Y00.572––
KBD_DRIVE_Y10.568––
KBD_DRIVE_Y20.565––
KBD_DRIVE_Y30.568––
KBD_DRIVE_Y40.580––
KBD_DRIVE_Y50.571––
KBD_DRIVE_Y60.513––
KBD_DRIVE_Y70.510––
KBD_ID_DETECT10.583––
KBD_ID10.787––
KBD_INT_L0.680––
KBD_LEFT_OPTION_KEY0.482––
KBD_LEFT_OPTION_L0.463––
KBD_RIGHT_SHIFT_KEY0.485––
KBD_RIGHT_SHIFT_L0.464––
KBD_SENSE_X00.569––
KBD_SENSE_X10.575––
KBD_SENSE_X20.570––
KBD_SENSE_X30.563––
KBD_SENSE_X40.565––
KBD_SENSE_X50.565––
KBD_SENSE_X60.517––
KBD_SENSE_X70.512––
KBD_SENSE_X80.515––
KBD_SENSE_X90.516––
KBD_SENSE_X100.566––
KBD_SENSE_X110.565––
KBD_SENSE_X120.566––
KBDBKLT_SW20.4275.000–
KBDLED_CATHODE10.671––
KBDLED_CATHODE1_ROL––
KBDLED_CATHODE20.665––
KBDLED_CATHODE2_ROL––
L83_FILT0.798––
L83_FLYC0.390––
L83_FLYN0.614––
L83_FLYP0.410––
L83_HSBIAS_FILT0.714––
L83_HSBIAS_FILT_REF0.638––
L83_VCP_FILT_GND0.000––
L83_VCP_FILTN0.736––
L83_VCP_FILTP0.394––
LCD_PWR_SLEW0.720––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.727––
LCDBKLT_FET_DRV_R0.584––
LCDBKLT_SW0.448––
LCDBKLT_TB_XWR1.260––
LDO_CORE0.378––
LED_CTRL0.568––
LED_ISET0.579––
LID_CTRL_DMIC0.694––
LID_OPEN_LEFT0.580––
LSX_HSW_P2R0.530––
LSX_HSW_R2P0.694––
MEM_BLDR_EN0.470––
MEM_BLDR_EN_L0.560––
MEM_RESET_L0.459––
MEM_RESET_R_L0.459––
MESA_BOOST_EN0.553––
MESA_BOOST_EN_CONN0.000––
MESA_INT0.485––
MESA_INT_CONN1.172––
MESA_PWR_EN0.477––
MIPI_DFR_CLK_FILT_CONN_N0.540––
MIPI_DFR_CLK_FILT_CONN_P0.540––
MIPI_DFR_CLK_N0.540––
MIPI_DFR_CLK_P0.540––
MIPI_DFR_DATA_FILT_CONN_N0.540––
MIPI_DFR_DATA_FILT_CONN_P0.540––
MIPI_DFR_DATA_N0.540––
MIPI_DFR_DATA_P0.540––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_N0.500––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_P0.500––
MIPI_FTCAM_CLK_ISOL_N0.500––
MIPI_FTCAM_CLK_ISOL_P0.500––
MIPI_FTCAM_CLK_N0.463––
MIPI_FTCAM_CLK_P0.465––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_N<0>0.500––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_P<0>0.500––
MIPI_FTCAM_DATA_ISOL_N<0>0.500––
MIPI_FTCAM_DATA_ISOL_P<0>0.500––
MIPI_FTCAM_DATA_N<0>0.471––
MIPI_FTCAM_DATA_P<0>0.466––
NFC_GPIO2_AO0.755––
NFC_GPIO3_AO0.755––
NFC_XTAL10.544––
NTC_A_CPUCORE0.626––
NTC_A_CPUCORE_RPOL––
ODT_10.155––
ODT_20.154––
ODT_30.155––
ODT_40.159––
OUT123_EN0.304––
P0V6_BLDR_L0.204––
P0V6_S3_COMP0.689––
P0V6_S3_COMP_RCOL––
P0V6_S3_FB0.295––
P0V6_S3_FB_R0.209––
P0V6_S3_FB_TOP0.199––
P0V6_S3_SKIP0.543––
P0V6_S3_SNUB0.200––
P0V6_S3_SS0.598––
P0V6_S3_SW0.200––
P0V8SLPDDR_SW00.0520.820–
P0V8SLPDDR_SW10.0520.820–
P0V9_LX0_SSD00.3000.900–
P0V9_LX1_SSD00.3000.900–
P0V9_TBT_SVR_PGND_R0.000––
P0V9_TBT_SVR_PGND_T0.000––
P0V9_TBT_SVR_PGND_W0.000––
P0V9_TBT_SVR_PGND_X0.000––
P0V9SLPDDR_SW00.0700.900–
P0V9SLPDDR_SW10.0700.900–
P1V1_BLDR_L0.168––
P1V1_BOOT_RC0.623––
P1V1_DRVH0.647––
P1V1_DRVH_R0.650––
P1V1_DRVL0.490––
P1V1_DRVL_R0.457––
P1V1_PHASE0.0441.100–
P1V1_SLPDDR_SOCFET_EN0.571––
P1V1_SNS0.167––
P1V1_SNS_R0.158––
P1V1_SW0.158––
P1V1_VBST0.621––
P1V1REG_AGND0.000––
P1V1REG_MODE0.539––
P1V1REG_TRIP0.746––
P1V1REG_VREF0.646––
P1V1REG_VREF_ROL––
P1V1S0SW_RAMP0.692––
P1V1S3_PGOOD0.543––
P1V1SLPDDR_RAMP0.700––
P1V1SLPS2R_SW00.2411.100–
P1V1SLPS2R_SW10.2411.100–
P1V2_WLANBT_VLX0.3201.200–
P1V05_VCCST_EN0.800––
P1V5_WLANBT_VLX0.3381.500–
P1V8_DFR_R0.720––
P1V8_G3S_DSCHG0.313––
P1V8_G3S_EN_ROL––
P1V8G3S_DSCHG_EN0.473––
P1V8G3S_DSCHG_EN_L0.565––
P1V8G3S_EN0.566––
P1V8G3S_SS0.623––
P1V8PRIM_EN0.530––
P1V8PRIM_FB_R1.961––
P1V8PRIM_FB_TOP0.289––
P1V8PRIM_PGOOD0.500––
P1V8SLPS2R_SW00.3591.800–
P1VPRIM_FB0.503––
P1VPRIM_SW00.5141.000–
P2V5_SW1_TPS62180_SSD00.4252.500–
P2V5_SW2_TPS62180_SSD00.4252.500–
P3V3G3H_COMP20.745––
P3V3G3H_COMP2_ROL––
P3V3G3H_CSN20.4505.000–
P3V3G3H_CSP21.293––
P3V3G3H_CSP2_R0.4505.000–
P3V3G3H_DRVH0.996––
P3V3G3H_DRVL0.561––
P3V3G3H_DRVL_R0.561––
P3V3G3H_EN_R0.592––
P3V3G3H_RF0.589––
P3V3G3H_SW0.430––
P3V3G3H_TG0.998––
P3V3G3H_VBST0.629––
P3V3G3H_VBST_R0.629––
P3V3G3H_VFB20.593––
P3V3G3H_VFB2_R0.432––
P3V3G3H_VFB2_RR1.361––
P3V3G3H_VSW0.4503.300–
P3V3G3HRTC_FB1.410––
P3V3G3HRTC_FB_R0.380––
P3V3G3HRTC_PGOOD0.692––
P3V3G3HRTC_PHASE10.388––
P3V3G3HRTC_PHASE20.3883.300–
P3V3G3HRTC_RA_R0.380––
P3V3G3HRTC_SS0.537––
P3V3G3S_EN0.556––
P3V3G3S_SS0.608––
P3V3MAIN_PGOOD0.583––
P3V3TBT_T_RAMP_SWR0.704––
P3V3TBT_T_RAMP_SXT0.720––
P3V3TBT_X_RAMP_SWR0.700––
P3V3TBT_X_RAMP_SXT0.720––
P5V_P3V3G3H_LDO_EN0.593––
P5VG3S_COMP10.746––
P5VG3S_COMP1_ROL––
P5VG3S_CSN10.427––
P5VG3S_CSP11.000––
P5VG3S_CSP1_R0.427––
P5VG3S_EN0.590––
P5VG3S_EN_R0.590––
P5VG3S_PGOOD0.584––
P5VG3S_SW0.426––
P5VG3S_VBST0.630––
P5VG3S_VBST_R0.629––
P5VG3S_VFB10.588––
P5VG3S_VFB1_R0.426––
P5VG3S_VFB1_RR0.625––
P5VG3S_VSW0.4335.000–
P5VP3V3_SKIPSEL0.487––
P5VP3V3_VREF20.492––
P5VP3V3_VREG30.5253.300–
P5VUSBC_AGND_VWR0.000––
P5VUSBC_AGND_VXT0.000––
P5VUSBC_BOOT_RC_VWR0.605––
P5VUSBC_BOOT_RC_VXT0.608––
P5VUSBC_DRVH_R_VWR0.956––
P5VUSBC_DRVH_R_VXT0.970––
P5VUSBC_DRVH_VWR0.952––
P5VUSBC_DRVH_VXT0.971––
P5VUSBC_FSEL_VWR0.554––
P5VUSBC_NEG_WR0.511––
P5VUSBC_NEG_XT0.491––
P5VUSBC_OCSET_VWR0.553––
P5VUSBC_OCSET_VXT0.555––
P5VUSBC_PGOOD_VXT0.556––
P5VUSBC_POS_WR0.511––
P5VUSBC_POS_XT0.491––
P5VUSBC_R_VWR0.5115.000–
P5VUSBC_R_VXT0.491––
P5VUSBC_RTN_DIV_VWR0.549––
P5VUSBC_RTN_DIV_VXT0.551––
P5VUSBC_RTN_DIV_XW_VWR0.000––
P5VUSBC_RTN_DIV_XW_VXT0.000––
P5VUSBC_SENSE_DIV_VWR0.547––
P5VUSBC_SENSE_DIV_VXT0.550––
P5VUSBC_SENSE_DIV_XW_VWR0.480––
P5VUSBC_SENSE_DIV_XW_VXT0.491––
P5VUSBC_SET_R_VWROL––
P5VUSBC_SET_R_VXTOL––
P5VUSBC_SET0_VWR0.550––
P5VUSBC_SET0_VXT0.556––
P5VUSBC_SET1_VWR0.550––
P5VUSBC_SET1_VXT0.555––
P5VUSBC_SREF_VWR0.550––
P5VUSBC_SREF_VXT0.553––
P5VUSBC_SW_VWR0.5115.000–
P5VUSBC_SW_VXT0.484––
P5VUSBC_VBST_VWR0.602––
P5VUSBC_VBST_VXT0.606––
P5VUSBC_VO_VWR0.551––
P5VUSBC_VO_VXT0.554––
PANEL_P3V3_EN0.947––
PANEL_P3V3_EN_D0.840––
PANEL_P5V_EN0.576––
PANEL_P5V_EN_D1.028––
PBUS_DIVIDER0.700––
PBUS_DIVIDER_OUT0.662––
PBUS_DIVIDER_REF0.667––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.486––
PBUSVSENS_EN_L0.457––
PBUSVSENS_EN_L_DIV0.457––
PCH_BATLOW_L0.8113.200–
PCH_BBR_FORCE_PWR0.660––
PCH_BT_AUDIO_SYNC0.540––
PCH_CLK38M4_XTALIN_R0.838––
PCH_CLK38M4_XTALOUT_R0.831––
PCH_CORE_VID00.537––
PCH_CORE_VID10.536––
PCH_I2C_UPC_SCL0.497––
PCH_I2C_UPC_SDA0.499––
PCH_PCIE_CLK100M_WLAN_N0.312––
PCH_PCIE_CLK100M_WLAN_P0.312––
PCH_PWRBTN_L0.7423.300–
PCH_RTC_RESET_L0.7642.900–
PCH_STRP_NO_REBOOT0.594––
PCH_UART_DEBUG_D2R_10.702––
PCH_UART_DEBUG_R2D_10.690––
PCH_UPC_I2C_INT_L0.510––
PCH_WLAN_AUDIO_SYNC0.517––
PCH_WLAN_CLKREQ_L0.805––
PCH_WLAN_CLKREQ_R_L0.517––
PCH_WLAN_DEV_WAKE0.577––
PCH_WLAN_PERST_L0.812––
PCIE_CLK100M_SOC_N0.303––
PCIE_CLK100M_SOC_P0.304––
PCIE_CLK100M_SSD0_01_N0.128––
PCIE_CLK100M_SSD0_01_P0.128––
PCIE_CLK100M_SSD0_23_N0.128––
PCIE_CLK100M_SSD0_23_P0.128––
PCIE_SSD0_D2R_C_N<1>0.332––
PCIE_SSD0_D2R_C_N<2>0.343––
PCIE_SSD0_D2R_C_P<1>0.337––
PCIE_SSD0_D2R_C_P<2>0.342––
PCIE_SSD0_D2R_N<0>0.406––
PCIE_SSD0_D2R_N<1>0.407––
PCIE_SSD0_D2R_N<2>0.410––
PCIE_SSD0_D2R_P<0>0.403––
PCIE_SSD0_D2R_P<1>0.404––
PCIE_SSD0_D2R_P<2>0.408––
PCIE_SSD0_R2D_C_N<1>0.339––
PCIE_SSD0_R2D_C_N<2>0.344––
PCIE_SSD0_R2D_C_P<1>0.340––
PCIE_SSD0_R2D_C_P<2>0.343––
PCIE_SSD0_R2D_N<1>0.411––
PCIE_SSD0_R2D_N<2>0.416––
PCIE_SSD0_R2D_P<1>0.410––
PCIE_SSD0_R2D_P<2>0.414––
PCPU_S0SW_EN0.509––
PD_P1V1_S3_EN0.516––
PD_UPC_R_GPIO10.694––
PD_UPC_R_GPIO90.708––
PD_UPC_R_GPIO100.705––
PD_UPC_T_GPIO10.688––
PD_UPC_T_GPIO90.712––
PD_UPC_T_GPIO100.713––
PD_UPC_W_GPIO10.691––
PD_UPC_W_GPIO90.711––
PD_UPC_W_GPIO100.712––
PD_UPC_WR_GPIO70.676––
PDM_DMIC_CLK00.531––
PDM_DMIC_CLK0_R0.477––
PDM_DMIC_CLK10.530––
PDM_DMIC_CLK1_R0.477––
PDM_DMIC_DATA00.465––
PDM_DMIC_DATA0_RR0.480––
PDM_DMIC_DATA10.465––
PDM_DMIC_DATA1_RR0.484––
PLT_RST_3V3_L0.633––
PLT_RST_L0.383––
PM_PCH_PWROK0.760––
PM_PCH_SYS_PWROK0.462––
PM_RSMRST_L0.4653.300–
PM_RSMRST_R_L0.4523.300–
PM_SLP_S0_3V3_L0.774––
PM_SLP_S0_L0.480––
PM_SLP_S0_R_LOL––
PM_SLP_S3_L_10.4603.300–
PM_SLP_S3_R_L0.524––
PM_SLP_S4_L0.801––
PM_SLP_S5_L0.801––
PM_SLP_SUS_L0.530––
PM_SLP_TIEOFF0.701––
PM_SYSRST_L0.803––
PM_SYSRST_R_L0.463––
PM_THRMTRIP_L0.192––
PMU_ACTIVE_READY0.496––
PMU_CALPE_ISENSE0.589––
PMU_CLK32K_PCH0.807––
PMU_CLK32K_PCH_1V00.861––
PMU_CLK32K_PCH_R0.772––
PMU_CLK32K_SOC0.476––
PMU_CLK32K_SOC_R0.511––
PMU_CLK32K_WLANBT0.481––
PMU_COLD_RESET_L0.471––
PMU_CPUDDR_ISENSE0.591––
PMU_CPUP5VREG_ISENSE0.592––
PMU_CPUVA_ISENSE0.591––
PMU_CPUVA_VSENSE0.593––
PMU_DDR1V2_ISENSE0.589––
PMU_DDRVDDQ_ISENSE0.593––
PMU_FORCE_DFU0.766––
PMU_IREF0.756––
PMU_LDO3_OUT0.593––
PMU_OCARINA_ISENSE0.592––
PMU_ONOFF_BUF_L0.579––
PMU_ONOFF_L0.5793.300–
PMU_ONOFF_R_L0.580––
PMU_ONOFF_R_L_CONN0.584––
PMU_OTHER3V3_HI_ISENSE0.590––
PMU_OTHER5V_HI_ISENSE0.590––
PMU_P5VUSBC_WR_ISENSE0.591––
PMU_P5VUSBC_XT_ISENSE0.589––
PMU_PVDDMAIN_EN0.770––
PMU_RSLOC_RST_L0.5183.300–
PMU_SSDNAND_ISENSE0.590––
PMU_SYS_ALIVE0.420––
PMU_TBT_XT_ISENSE0.591––
PMU_VDD_HI0.653––
PMU_VDD_MAX0.550––
PMU_VREF0.635––
PMU_XTAL1_R0.793––
PMU_XTAL20.793––
PP_VDD_SE_VDDC0.343––
PP_VDD_SE_VDDNV0.367––
PP_VDD_SE_VDDPLL0.367––
PP_VDD_SE_VHV0.325––
PP_VDD_SE_VREF0.697––
PP0V6_S30.2000.600–
PP0V6_S3_REG_R0.200––
PP0V8_SLPS2R0.224––
PP0V9_SLPDDR0.0700.900–
PP0V9_SSD00.3000.900–
PP0V9_SSD0_FB_DIS0.298––
PP0V9_SSD0_S4E0_VDD_PLL0.307––
PP0V9_SSD0_S4E1_VDD_PLL0.295––
PP0V9_SSD0_S4E2_VDD_PLL0.312––
PP0V9_SSD0_S4E3_VDD_PLL0.301––
PP0V9_TBT_LVR_R0.516––
PP0V9_TBT_LVR_T0.525––
PP0V9_TBT_LVR_W0.5170.900–
PP0V9_TBT_LVR_X0.523––
PP0V9_TBT_R_LC0.361––
PP0V9_TBT_SVR_IND_R0.4160.900–
PP0V9_TBT_SVR_IND_T0.3970.900–
PP0V9_TBT_SVR_IND_W0.4250.900–
PP0V9_TBT_SVR_IND_X0.4000.900–
PP0V9_TBT_SVR_R0.4160.900–
PP0V9_TBT_SVR_T0.3970.900–
PP0V9_TBT_SVR_W0.4250.900–
PP0V9_TBT_SVR_X0.4000.900–
PP0V9_TBT_T_LC0.375––
PP0V9_TBT_W_LC0.358––
PP0V9_TBT_X_LC0.367––
PP0V82_SLPDDR0.0520.820–
PP1P05_PCH_EXT0.5141.000–
PP1V1_S0SW0.467––
PP1V1_S30.0441.100–
PP1V1_S3_CPU0.158––
PP1V1_S3_REG_R0.0441.100–
PP1V1_SLPDDR0.330––
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.330––
PP1V1_SLPS2R0.2411.100–
PP1V2_AWAKE0.522––
PP1V2_AWAKE_SOC_PCIEPLL_F0.522––
PP1V2_AWAKE_SOC_PLLCPU_F0.377––
PP1V2_AWAKE_SOC_PLLSOC_F0.525––
PP1V2_WLANBT0.294––
PP1V2_WLANBT_C0.3201.200–
PP1V05_PCH_OUT_FET0.192––
PP1V05_PRIM_OUT_PCH0.193––
PP1V05_S0_CPU_VCCPLL0.193––
PP1V05_S0_CPU_VCCST0.1131.000–
PP1V05_S0SW_VCCSTG0.125––
PP1V5_UPC_LDO_CORE_R0.5051.500–
PP1V5_UPC_LDO_CORE_T0.5201.500–
PP1V5_UPC_LDO_CORE_W0.513––
PP1V5_UPC_LDO_CORE_X0.522––
PP1V05_VCCSTG_OUT0.126––
PP1V5_WLANBT0.326––
PP1V5_WLANBT_C0.3381.500–
PP1V8_AWAKE0.4021.800–
PP1V8_AWAKE_SOC_FMON_RC0.455––
PP1V8_AWAKE_SOC_TSADC_RC0.402––
PP1V8_CODEC0.303––
PP1V8_CODEC_VCP0.303––
PP1V8_CODEC_VCP_SEL0.303––
PP1V8_CODEC_VL0.303––
PP1V8_CODEC_VL_SEL0.303––
PP1V8_DFR0.535––
PP1V8_DMIC0.322––
PP1V8_G3S0.303––
PP1V8_G3S_WLANBT0.305––
PP1V8_IO_SSD00.375––
PP1V8_IO_SSD0_R2OL––
PP1V8_MESA0.530––
PP1V8_MESA_FILT_CONN0.532––
PP1V8_PCH_CLKLDO0.270––
PP1V8_PCH_CLKLDO_R0.288––
PP1V8_S0SW0.369––
PP1V8_S30.279––
PP1V8_S3_MEM0.279––
PP1V8_S4SW_SNS0.492––
PP1V8_S50.2701.800–
PP1V8_S5_THMSNSA_R0.291––
PP1V8_S5_THMSNSB_R0.290––
PP1V8_SLPS2R0.3591.800–
PP1V8_SLPS2R_PMUVDDGPIO0.736––
PP1V8_SLPS2R_SOC_LPADC_RC0.405––
PP1V8_SLPS2R_SOC_LPOSC_RC0.410––
PP1V24_S5_PCH_VCCDPHY0.369––
PP1V25_SLPS2R_SMC_AVREF0.681––
PP2V5_ADC1_VREFOL––
PP2V5_NAND_SSD00.4252.500–
PP3V_G3H_RTC0.533––
PP3V0_MESA0.556––
PP3V0_MESA_FILT_CONN0.555––
PP3V3_AWAKE0.639––
PP3V3_CODEC_LDO_INOL––
PP3V3_CODEC_VP0.369––
PP3V3_G3H0.4503.300–
PP3V3_G3H_DFR0.450––
PP3V3_G3H_MESA_SW0.369––
PP3V3_G3H_PMU_VDDMAIN0.450––
PP3V3_G3H_PMU_VINRTC_R0.368––
PP3V3_G3H_RSLOC0.369––
PP3V3_G3H_RTC0.3423.300–
PP3V3_G3H_RTC_MESA0.369––
PP3V3_G3H_RTC_REG_R0.3883.300–
PP3V3_G3H_SSD00.3693.300–
PP3V3_G3HSW_DFR0.567––
PP3V3_G3S0.338––
PP3V3_G3S_KBD0.338––
PP3V3_G3S_TPAD0.338––
PP3V3_G3S_WLANBT0.338––
PP3V3_S0_TBT_WR_ISNS_R0.370––
PP3V3_S0_TBT_XT_ISNS_R0.450––
PP3V3_S0SW_LCD0.492––
PP3V3_S0SW_LCD_R0.492––
PP3V3_S50.3563.300–
PP3V3_TBT_ANA_R0.555––
PP3V3_TBT_ANA_T0.556––
PP3V3_TBT_ANA_W0.552––
PP3V3_TBT_ANA_X0.560––
PP3V3_TBT_LC_R0.572––
PP3V3_TBT_LC_T0.578––
PP3V3_TBT_LC_W0.572––
PP3V3_TBT_LC_X0.578––
PP3V3_TBT_R_S00.517––
PP3V3_TBT_R_SX0.517––
PP3V3_TBT_S0_SVR_R0.517––
PP3V3_TBT_S0_SVR_T0.523––
PP3V3_TBT_S0_SVR_W0.517––
PP3V3_TBT_S0_SVR_X0.523––
PP3V3_TBT_T_S00.523––
PP3V3_TBT_T_S0_R_SWR0.517––
PP3V3_TBT_T_S0_R_SXT0.523––
PP3V3_TBT_T_SW_SWR0.369––
PP3V3_TBT_T_SW_SXT0.434––
PP3V3_TBT_T_SX0.521––
PP3V3_TBT_VCCA_R0.517––
PP3V3_TBT_VCCA_T0.523––
PP3V3_TBT_VCCA_W0.517––
PP3V3_TBT_W_S00.517––
PP3V3_TBT_W_SX0.517––
PP3V3_TBT_X_S00.523––
PP3V3_TBT_X_S0_R_SWR0.517––
PP3V3_TBT_X_S0_R_SXT0.523––
PP3V3_TBT_X_SW_SWR0.369––
PP3V3_TBT_X_SW_SXT0.434––
PP3V3_TBT_X_SX0.522––
PP3V3_UPC_R_LDO0.503––
PP3V3_UPC_R_VOUTLV0.538––
PP3V3_UPC_T_LDO0.5003.300–
PP3V3_UPC_T_VOUTLV0.554––
PP3V3_UPC_W_LDO0.4983.300–
PP3V3_UPC_W_VOUTLV0.537––
PP3V3_UPC_X_LDO0.4733.300–
PP3V3_UPC_X_VOUTLV0.553––
PP5V_COREVR_VCC0.427––
PP5V_EADC1_AVDDOL––
PP5V_G3S0.4335.000–
PP5V_G3S_ALSCAM0.433––
PP5V_G3S_ALSCAM_F0.433––
PP5V_G3S_CPUREG0.426––
PP5V_G3S_DFR_FILT0.429––
PP5V_G3S_KBD0.4275.000–
PP5V_G3S_TPAD0.433––
PP5V_G3S_TPAD_CONN0.424––
PP5V_MAIN_VCORE10.425––
PP5V_MAIN_VCORE20.425––
PP5V_MAIN_VCORE30.426––
PP5V_S0_BKLT_A0.436––
PP5V_S0_BKLT_D0.435––
PP5V_S0SW_LCD0.576––
PP5V_S0SW_LCD_ISNS_R0.576––
PP5V_S4_WLAN_ISNS_DOL––
PP5V_S4_WR_USBC0.5115.000–
PP5V_S4_XT_USBC0.4915.000–
PP5V_S4SW_ISNSOL––
PP5V_S5_LDO0.494––
PP5V_USBC_PVCC_VWR0.428––
PP5V_USBC_PVCC_VXT0.430––
PP5V_USBC_VCC_VWR0.426––
PP5V_USBC_VCC_VXT0.429––
PP5V_VDD2_V5IN0.424––
PP16V0_MESA0.648––
PP16V0_MESA_FILT_CONN0.665––
PP17V0_MOJAVE_LDOIN0.587––
PP20V_USBC_R_VBUS0.13720.000–
PP20V_USBC_T_VBUS0.13820.000–
PP20V_USBC_W_VBUS0.13520.000–
PP20V_USBC_X_VBUS0.13920.000–
PPBUS_G3H0.51013.100–
PPBUS_G3H_SPKRAMP_LEFT0.51012.000–
PPBUS_G3H_SSD00.51013.100–
PPBUS_HS_CPU0.51013.100–
PPDCIN_G3H0.55020.000–
PPDCIN_G3H_CHGR0.56220.000–
PPHV_INT_G3H_R0.55020.000–
PPHV_INT_G3H_T0.55020.000–
PPHV_INT_G3H_W0.54920.000–
PPHV_INT_G3H_X0.55020.000–
PPVBAT_G3H_CHGR_R0.51013.100–
PPVBAT_G3H_CHGR_REG0.51013.100–
PPVBAT_G3H_CONN1.574––
PPVCC_CPU_PH10.0901.50080.000R
PPVCC_CPU_PH20.0901.50080.000R
PPVCC_CPU_PH30.0901.50080.000R
PPVCC_OBS_CD0.080––
PPVCCIN_AUX_PCH_PRIM0.3801.800–
PPVCCIN_S0_CPU0.0901.50080.000R
PPVCCINAUX1_PVCC0.476––
PPVCCINAUX1_VCC0.426––
PPVCCIO_OUT0.083––
PPVCCQ_ANI_SSD00.3001.800–
PPVCCQ_SSD0_FB_DIS0.288––
PPVDD_SE_VDDA0.338––
PPVDDCPU_AWAKE0.0131.060–
PPVDDCPUSRAM_AWAKE0.3941.060–
PPVIN_G3H_P3V3G3H0.51013.100–
PPVIN_G3H_P3V3G3HRTC0.510––
PPVIN_G3H_P3V3G3HRTC_R0.51712.000–
PPVIN_G3H_P5VG3S0.51013.100–
PPVIN_RFLDO_WLANBT0.328––
PPVIN_RFLDO_WLANBT_C0.3541.800–
PPVIN_S0_CPUVR_VIN0.494––
PPVIN_S0_PRIM1V80.51013.100–
PPVIN_S0PRIM_1V8_RC0.488––
PPVIN_S0SW_LCDBKLT0.91012.900–
PPVIN_S0SW_LCDBKLT_F0.510––
PPVIN_S0SW_LCDBKLT_R0.510––
PPVIN_SW_LCDBKLT_SW0.91012.900–
PPVNN_PCH_EXT0.5231.000–
PPVOUT_BKLT_FB20.622––
PPVOUT_S0_KBDLED0.653––
PPVOUT_S0_KBDLED_R0.62240.000–
PPVOUT_S0_LCDBKLT1.260––
PPVOUT_S0_LCDBKLT_F1.26046.000–
PPVTT_VTTREF0.489––
PROG1_CPUCOREVR0.620––
PROG2_CPUCOREVR0.620––
PROG4_CPUCOREVR0.623––
PROG5_CPUCOREVR0.622––
PVCCCORE_PH1_AGND0.000––
PVCCCORE_PH2_AGND0.000––
PVCCCORE_PH3_AGND0.000––
PVCCINAUX_DSCHG0.420––
PVCCINAUX_DSCHG_EN0.477––
PVCCINAUX_DSCHG_EN_L0.453––
PVCCPCOREPRIM_FB_N0.000––
PVCCPCOREPRIM_FB_P0.518––
PVCCPCOREPRIM_SW00.5231.000–
PVCCPLLOC_EN0.769––
PVCCQ_LX00.3001.800–
PVCCST_EN0.775––
PVCCSTG_DSCHG0.505––
PVCCSTG_DSCHG_EN0.468––
PVCCSTG_DSCHG_EN_L0.511––
PVDD2_EN_R0.558––
PVDD2_REFIN0.697––
PVDDCPUAWAKE_FB0.015––
PVDDCPUAWAKE_FB_R0.015––
PVDDCPUAWAKE_SW00.0131.060–
PVDDCPUAWAKE_SW10.0131.060–
PVDDCPUAWAKE_SW20.0131.060–
PVDDCPUAWAKE_SW30.0131.060–
PVDDCPUSRAMAWAKE_FB0.400––
PVDDCPUSRAMAWAKE_SW00.3941.060–
PVDDQ_EN0.558––
PVDDQ_EN_LEDOL––
PVDDQ_PGOOD0.616––
PVIN_RFLDO_WLANBT_VLX0.3541.800–
REG_FB_P1V8PRIM1.391––
REG_PHASE_1V8PRIM0.2701.800–
REG_PHASE_1V8PRIM_MID0.2701.800–
REG_SSTR_P1V8PRIM0.746––
REG_VOS_P1V8PRIM0.297––
RSLOC_RST_L0.487––
RSMRSTL_R0.661––
RTN_A_CPUCORE0.002––
SAVE_BAT_G0.771––
SAVE_BAT_S1.560––
SD3_RCOMP0.201––
SE_CTLR_FW_DWLD0.473––
SE_DEV_WAKE0.473––
SE_HOST_WAKE0.470––
SE_HOST_WAKE_R0.470––
SE_PWR_EN0.757––
SE_RX_N0.512––
SE_RX_P0.512––
SENSOR_PWR_EN0.718––
SEP_CAM_DISABLE_DFF_L0.504––
SEP_CAM_DISABLE_L0.000––
SEP_DISABLE_STROBE0.469––
SEP_DMIC_DISABLE_L0.470––
SEP_DMIC_DISABLE_OUT_L0.489––
SEP_WP0.747––
SMBUS_3V3_BATT_SCL0.997––
SMBUS_3V3_BATT_SDA0.973––
SMC_BMON_ISENSE0.810––
SMC_CPU_HS_ISENSE0.810––
SMC_CPUVCCIN_VSENSE0.808––
SMC_DCIN_ISENSE0.809––
SMC_DCIN_VSENSE0.805––
SMC_DEBUGPRT_R_RX0.479––
SMC_DEBUGPRT_R_TX0.480––
SMC_DEBUGPRT_RX0.475––
SMC_DEBUGPRT_TX0.479––
SMC_DPWROK1V80.464––
SMC_FAN_0_PWM0.480––
SMC_LID_LEFT0.466––
SMC_LID_RIGHT0.466––
SMC_PBUS_VSENSE0.805––
SMC_PCH_PWROK0.434––
SMC_PCH_SYS_PWROK0.431––
SMC_PECI_RX0.470––
SMC_PECI_TX0.466––
SMC_PECI_TX_R0.466––
SMC_PP3V3_WLANBT_ISENSE0.811––
SMC_PROCHOT_L0.463––
SMC_RSMRST_L0.4321.800–
SMC_SYSRST_L0.432––
SMCRST_TIEOFF0.709––
SOC_CLKREQ_BUF_L0.528––
SOC_CLKREQ_L0.523––
SOC_CLKREQ_R_L0.471––
SOC_CLKREQ_SW_EN0.636––
SOC_COLD_RESET_L0.474––
SOC_DDR0_RREF0.527––
SOC_DDR0_ZQ0.397––
SOC_DDR1_RREF0.536––
SOC_DDR2_RREF0.525––
SOC_DFU_STATUS0.478––
SOC_DOCK_CONNECT0.505––
SOC_FORCE_DFU0.479––
SOC_HOLD_RESET0.475––
SOC_JTAG_SEL0.472––
SOC_KBD_BKLT_PWM0.483––
SOC_KBD_BKLT_PWM_R0.483––
SOC_MIPI0C_REXT0.813––
SOC_MIPI1C_REXT0.812––
SOC_MIPID_REXT0.812––
SOC_PCIE_DN_REXT0.785––
SOC_PCIE_STG0_REXT0.784––
SOC_PCIE_STG1_REXT0.787––
SOC_PCIE_UP_REXT0.784––
SOC_PERST_L0.467––
SOC_SOCHOT_L0.478––
SOC_TESTMODE0.473––
SOC_USB_REXT0.202––
SOC_USB_VBUS0.404––
SOC_VDDCPU_SENSE0.020––
SOC_WDOG0.475––
SPARE_UPC_R0.674––
SPARE_UPC_R_DBG0.625––
SPARE_UPC_T0.679––
SPARE_UPC_W0.676––
SPARE_UPC_W_DBG0.640––
SPARE_UPC_X0.702––
SPARE_UPC_X_DBG0.653––
SPI_DFR_CLK0.494––
SPI_DFR_CLK_R0.476––
SPI_DFR_CS_L0.481––
SPI_DFR_MISO_R0.500––
SPI_DFR_MOSI0.485––
SPI_DFR_MOSI_R0.476––
SPI_MESA_CLK0.489––
SPI_MESA_CLK_CONN0.570––
SPI_MESA_CLK_R0.475––
SPI_MESA_MISO0.480––
SPI_MESA_MISO_CONN0.493––
SPI_MESA_MOSI0.463––
SPI_MESA_MOSI_CONN0.513––
SPI_MESA_MOSI_R0.475––
SPI_SOCROM_CLK_R0.445––
SPI_SOCROM_CS_L0.475––
SPI_SOCROM_MISO0.462––
SPI_SOCROM_MOSI0.480––
SPI_SOCROM_MOSI_R0.466––
SPI_SOCROM_WP_L0.553––
SPI_TPAD_3V3_CLK0.561––
SPI_TPAD_3V3_CLK_R0.506––
SPI_TPAD_3V3_CS_L0.635––
SPI_TPAD_3V3_MISO0.636––
SPI_TPAD_3V3_MOSI0.640––
SPI_TPAD_3V3_MOSI_R0.625––
SPI_TPAD_CLK0.496––
SPI_TPAD_CLK_R0.479––
SPI_TPAD_CS_L0.464––
SPI_TPAD_MISO0.478––
SPI_TPAD_MISO_R0.496––
SPI_TPAD_MOSI0.496––
SPI_TPAD_MOSI_R0.478––
SPKR_ID00.484––
SPKR_ID10.481––
SPKRAMP_INT_L0.365––
SPKRAMP_LT_AREG0.583––
SPKRAMP_LT_DREG0.525––
SPKRAMP_LT_MODE0.000––
SPKRAMP_LW_AREG0.583––
SPKRAMP_LW_DREG0.524––
SPKRAMP_LW_MODE0.407––
SPKRAMP_RESET_L0.365––
SPKRAMP_RT_AREG0.583––
SPKRAMP_RT_BSTN0.772––
SPKRAMP_RT_BSTP0.772––
SPKRAMP_RT_DREG0.523––
SPKRAMP_RW_AREG0.583––
SPKRAMP_RW_BSTN0.772––
SPKRAMP_RW_BSTP0.772––
SPKRAMP_RW_DREG0.522––
SPKRAMP_RW_MODE0.467––
SPKRCONN_LT_OUTN0.446––
SPKRCONN_LT_OUTP0.445––
SPKRCONN_LW_OUTN0.443––
SPKRCONN_LW_OUTP0.446––
SPKRCONN_RT_OUTN0.442––
SPKRCONN_RT_OUTP0.445––
SPKRCONN_RW_OUTN0.447––
SPKRCONN_RW_OUTP0.453––
SPMI_CLK0.496––
SPMI_CLK_R0.476––
SPROM_CLK0.500––
SPROM_CS0.499––
SPROM_CS_R0.695––
SPROM_DIN0.507––
SPROM_DOUT0.505––
SSD_BFH0.433––
SSD_PMU_RESET_L0.475––
SSD0_CLK24M0.442––
SSD0_CLK24M_010.446––
SSD0_CLK24M_230.452––
SSD0_CLKREQ0_L0.456––
SSD0_CLKREQ1_L0.455––
SSD0_CR_P2V5_PGOOD0.565––
SSD0_FORCE_EN0.570––
SSD0_LPB_L0.445––
SSD0_OCARINA_IREF0.750––
SSD0_OCARINA_LPB_L0.445––
SSD0_OCARINA_PFN_L0.445––
SSD0_OCARINA_PGOOD0.756––
SSD0_OCARINA_POK20.000––
SSD0_OCARINA_RESET_L0.445––
SSD0_OCARINA_TCAL0.770––
SSD0_OCARINA_TDEV10.370––
SSD0_OCARINA_TDEV20.770––
SSD0_OCARINA_VDD_LDO0.360––
SSD0_OCARINA_VR2_DIS0.663––
SSD0_OCARINA_VREF0.766––
SSD0_OCARINA_WP_L0.371––
SSD0_PCIE_RESET_L0.430––
SSD0_S4E_JTAG_SEL0.444––
SSD0_S4E_JTAG_TRST_L0.444––
SSD0_S4E_UART_TX0.490––
SSD0_S4E0_ANI0_VREF0.572––
SSD0_S4E0_ANI1_VREF0.569––
SSD0_S4E0_AVDD18_PLL0.290––
SSD0_S4E0_DROOP_L0.495––
SSD0_S4E0_JTAG_TDI0.491––
SSD0_S4E0_JTAG_TDO0.464––
SSD0_S4E0_PCI_AVDD_H0.290––
SSD0_S4E0_PCIE_RESREF0.783––
SSD0_S4E0_SWD_UID00.491––
SSD0_S4E0_SWD_UID10.492––
SSD0_S4E0_VPP0.559––
SSD0_S4E0_ZQ_C0.100––
SSD0_S4E0_ZQ_L0.300––
SSD0_S4E1_ANI0_VREF0.566––
SSD0_S4E1_ANI1_VREF0.563––
SSD0_S4E1_AVDD18_PLL0.292––
SSD0_S4E1_JTAG_TDO0.465––
SSD0_S4E1_PCI_AVDD_H0.292––
SSD0_S4E1_PCIE_RESREF0.784––
SSD0_S4E1_SWD_UID00.489––
SSD0_S4E1_SWD_UID10.487––
SSD0_S4E1_ZQ_C0.100––
SSD0_S4E1_ZQ_L0.302––
SSD0_S4E2_ANI0_VREF0.590––
SSD0_S4E2_ANI1_VREF0.591––
SSD0_S4E2_AVDD18_PLL0.290––
SSD0_S4E2_DROOP_L0.499––
SSD0_S4E2_JTAG_TDO0.476––
SSD0_S4E2_PCI_AVDD_H0.290––
SSD0_S4E2_PCIE_RESREF0.786––
SSD0_S4E2_SWD_UID00.497––
SSD0_S4E2_SWD_UID10.495––
SSD0_S4E2_VPP0.558––
SSD0_S4E2_ZQ_C0.100––
SSD0_S4E2_ZQ_L0.302––
SSD0_S4E3_AVDD18_PLL0.292––
SSD0_S4E3_JTAG_TDO0.511––
SSD0_S4E3_PCI_AVDD_H0.292––
SSD0_S4E3_ZQ_C0.100––
SSD0_STG01_ADDR0.570––
SSD0_SWCLK0.434––
SSD0_SWDIO0.432––
SSD0_TPS62180_FB1.413––
SSD0_TPS62180_FB_R0.320––
SSD0_TPS62180_SS0.538––
SSD0_VR_2V5_EN0.640––
SSD0_VR_P2V5_EN_R0.640––
SSD0_WP_L0.371––
SWD_SOC_SWCLK0.474––
SWD_SOC_SWCLK_R0.505––
SWD_SOC_SWCLK_T0.505––
SWD_SOC_SWCLK_X0.506––
SWD_SOC_SWDIO0.473––
SWD_SOC_SWDIO_R0.504––
SWD_SOC_SWDIO_T0.505––
SWD_SOC_SWDIO_X0.505––
SYS_DETECTOL––
SYS_DETECT_L0.590––
TBT_POC_RESET0.532––
TBT_PWR_EN0.775––
TBT_R_FLASH_SHARE_EN0.594––
TBT_R_FORCE_PWR0.580––
TBT_R_GPIO_50.595––
TBT_R_SPI_CLK0.562––
TBT_R_SPI_CS_L0.562––
TBT_R_SPI_MISO0.556––
TBT_R_SPI_MOSI0.557––
TBT_RBIAS_R0.773––
TBT_RBIAS_T0.777––
TBT_RBIAS_W0.774––
TBT_RBIAS_X0.779––
TBT_RSENSE_R0.000––
TBT_RSENSE_T0.000––
TBT_RSENSE_W0.000––
TBT_T_FLASH_MSTR_H_SLV_L0.600––
TBT_T_FLASH_SHARE_EN0.599––
TBT_T_FORCE_PWR0.600––
TBT_T_GPIO_50.600––
TBT_T_GPIO_60.600––
TBT_T_GPIO_120.600––
TBT_T_S0_PWR_EN_SWR0.538––
TBT_T_S0_PWR_EN_SXT0.540––
TBT_T_SPI_CLK0.558––
TBT_T_SPI_CS_L0.567––
TBT_T_SPI_MISO0.572––
TBT_T_SPI_MOSI0.571––
TBT_T_THERM_D_N0.000––
TBT_T_THERM_D_P0.614––
TBT_TEST_PWR_GOOD_R0.101––
TBT_TEST_PWR_GOOD_T0.100––
TBT_TEST_PWR_GOOD_W0.100––
TBT_TEST_PWR_GOOD_X0.100––
TBT_W_FLASH_MSTR_H_SLV_L0.598––
TBT_W_FLASH_SHARE_EN0.595––
TBT_W_FORCE_PWR0.586––
TBT_W_GPIO_50.597––
TBT_W_GPIO_60.598––
TBT_W_GPIO_120.596––
TBT_W_SPI_CLK0.565––
TBT_W_SPI_CS_L0.565––
TBT_W_SPI_MISO0.554––
TBT_W_SPI_MOSI0.558––
TBT_WR_FLASH_BUSY_L0.561––
TBT_WR_PERST_L0.562––
TBT_WR_ROM_HOLD_L0.662––
TBT_WR_ROM_WP_L0.660––
TBT_WR_SPI_CLK0.564––
TBT_WR_SPI_CLK_DBG0.665––
TBT_WR_SPI_CS_L0.565––
TBT_WR_SPI_MISO0.554––
TBT_WR_SPI_MOSI0.559––
TBT_X_FLASH_MSTR_H_SLV_L0.591––
TBT_X_FLASH_SHARE_EN0.604––
TBT_X_FORCE_PWR0.590––
TBT_X_GPIO_50.611––
TBT_X_GPIO_60.609––
TBT_X_GPIO_120.610––
TBT_X_S0_PWR_EN_SWR0.537––
TBT_X_S0_PWR_EN_SXT0.539––
TBT_X_SPI_CLK0.558––
TBT_X_SPI_CS_L0.571––
TBT_X_SPI_MISO0.570––
TBT_X_SPI_MOSI0.572––
TBT_XT_FLASH_BUSY_L0.569––
TBT_XT_PERST_L0.572––
TBT_XT_ROM_HOLD_L0.710––
TBT_XT_ROM_WP_L0.710––
TBT_XT_SPI_CLK0.555––
TBT_XT_SPI_CLK_DBG0.655––
TBT_XT_SPI_CS_L0.570––
TBT_XT_SPI_MISO0.571––
TBT_XT_SPI_MOSI0.573––
TBT_XTAL25M_IN_R0.834––
TBT_XTAL25M_IN_R_R0.834––
TBT_XTAL25M_IN_R_W0.834––
TBT_XTAL25M_IN_W0.834––
TBT_XTAL25M_OUT_R0.790––
TBT_XTAL25M_OUT_R_R0.790––
TBT_XTAL25M_OUT_R_W0.788––
TBT_XTAL25M_OUT_W0.788––
TEST_SOC_AMUXOUT0.812––
TEST_SOC_TST_CLKOUT0.479––
THMSNSA_DN0.000––
TP_BMON_IOUTOL––
TP_CPU_BPM_L<2>0.237––
TP_CPU_BPM_L<3>0.235––
TP_CPU_RSVD_AB10.260––
TP_CPU_RSVD_AV20.315––
TP_CPU_RSVD_AW20.314––
TP_CPU_RSVD_K20.837––
TP_DFR_TOUCH_GPIO2OL––
TP_DFR_TOUCH_PANEL_DETECTOL––
TP_DP_R_HPD0.706––
TP_DP_T_HPD0.711––
TP_DP_W_HPD0.715––
TP_DP_X_HPD0.713––
TP_FAN_LT_OTP1OL––
TP_FAN_LT_OTP2OL––
TP_FAN_RT_OTP1OL––
TP_FAN_RT_OTP2OL––
TP_I2S_BT_D2R0.737––
TP_I2S_BT_R2D0.704––
TP_JTAG_SOC_TDI0.477––
TP_JTAG_SOC_TDO0.475––
TP_JTAG_SOC_TRST_L0.475––
TP_LCD_IRQ_LOL––
TP_SMBUS_TBT_SCL_R0.597––
TP_SMBUS_TBT_SCL_T0.601––
TP_SMBUS_TBT_SCL_W0.598––
TP_SMBUS_TBT_SCL_X0.610––
TP_SMBUS_TBT_SDA_R0.595––
TP_SMBUS_TBT_SDA_T0.601––
TP_SMBUS_TBT_SDA_W0.598––
TP_SMBUS_TBT_SDA_X0.610––
TP_SMC_FIXTURE_MODE_L0.478––
TP_SOC_DEBUGPRT_RX0.478––
TP_SOC_DEBUGPRT_TX0.479––
TP_SSD0_OCARINA_NAND_VCC_DET0.757––
TP_USBC_PP20V_A_CWROL––
TP_USBC_PP20V_A_CXTOL––
TP_USBC_PP20V_B_CWROL––
TP_USBC_PP20V_B_CXTOL––
TP_WLAN_PMU_TEST0.735––
TPAD_3V3_ACTUATOR_DISABLE_L0.940––
TPAD_3V3_SPI_EN0.629––
TPAD_3V3_SPI_INT_L0.918––
TPAD_ACTUATOR_DISABLE_L0.475––
TPAD_KBD_WAKE_L0.476––
TPAD_SPI_EN0.477––
TPAD_SPI_INT_L0.473––
UART_BT_BUF_CTS_L0.479––
UART_BT_BUF_D2R0.447––
UART_BT_BUF_R2D0.479––
UART_BT_BUF_RTS_L0.448––
UART_SE_D2R0.471––
UART_SE_D2R_CTS_L0.471––
UART_SE_R2D0.451––
UART_SE_R2D_RTS_L0.451––
UART_WLAN_D2R0.477––
UART_WLAN_D2R_CTS_L0.476––
UNCONNECTED_1260.700––
UNCONNECTED_385OL––
UPC_5V_EN_R_VWR0.552––
UPC_5V_EN_R_VXT0.556––
UPC_I2C_INT_L0.472––
UPC_PMU_RESET0.607––
UPC_R_FAULT_L0.683––
UPC_R_FORCE_PWR0.582––
UPC_R_OSC_R0.465––
UPC_R_OSC_T0.475––
UPC_R_OSC_W0.465––
UPC_R_OSC_X0.479––
UPC_R_RESET0.588––
UPC_R_SER_DBG0.688––
UPC_R_SWD_CLK0.598––
UPC_R_SWD_DATA0.711––
UPC_SS_R0.579––
UPC_SS_T0.592––
UPC_SS_W0.580––
UPC_SS_X0.591––
UPC_T_FAULT_L0.694––
UPC_T_FORCE_PWR0.604––
UPC_T_RESET0.604––
UPC_T_SER_DBG0.674––
UPC_T_SPI_CLK0.575––
UPC_T_SPI_CS_L0.583––
UPC_T_SPI_MISO0.589––
UPC_T_SPI_MOSI0.592––
UPC_T_SWD_CLK0.599––
UPC_T_SWD_DATA0.710––
UPC_W_FAULT_L0.687––
UPC_W_FORCE_PWR0.590––
UPC_W_RESET0.590––
UPC_W_SER_DBG0.689––
UPC_W_SPI_CLK0.579––
UPC_W_SPI_CS_L0.579––
UPC_W_SPI_MISO0.568––
UPC_W_SPI_MOSI0.573––
UPC_W_SWD_CLK0.599––
UPC_W_SWD_DATA0.712––
UPC_WR_5V_EN0.627––
UPC_WR_UART_RX0.553––
UPC_WR_UART_TX0.553––
UPC_X_FAULT_L0.690––
UPC_X_FORCE_PWR0.595––
UPC_X_RESET0.607––
UPC_X_SER_DBG0.675––
UPC_X_SWD_CLK0.597––
UPC_X_SWD_DATA0.707––
UPC_X_VRET_R0.000––
UPC_X_VRET_T0.005––
UPC_X_VRET_W0.000––
UPC_X_VRET_X0.005––
UPC_XT_5V_EN0.553––
UPC_XT_UART_RX0.565––
UPC_XT_UART_TX0.563––
USB_FIXT1_N0.424––
USB_FIXT1_P0.425––
USB_FIXT2_N0.426––
USB_FIXT2_P0.425––
USB_SOC_N0.718––
USB_SOC_P0.717––
USB_UPC_1_N_R0.432––
USB_UPC_1_N_T0.566––
USB_UPC_1_N_W0.429––
USB_UPC_1_N_X0.569––
USB_UPC_1_P_R0.431––
USB_UPC_1_P_T0.559––
USB_UPC_1_P_W0.431––
USB_UPC_1_P_X0.560––
USB_UPC_X2_N0.718––
USB_UPC_X2_P0.712––
USB2_TBT_R_N0.432––
USB2_TBT_R_P0.431––
USB2_TBT_T_N0.566––
USB2_TBT_T_P0.559––
USB2_TBT_W_N0.428––
USB2_TBT_W_P0.430––
USB2_TBT_X_N0.572––
USB2_TBT_X_P0.560––
USB3_BSSB_D2R_N0.394––
USB3_BSSB_D2R_P0.397––
USB3_BSSB_D2R_R_N0.394––
USB3_BSSB_D2R_R_P0.397––
USB3_BSSB_R2D_N0.705––
USB3_BSSB_R2D_P0.705––
USB3_EXTC_D2R_N0.318––
USB3_EXTC_D2R_P0.318––
USB3_EXTC_R2D_C_N0.311––
USB3_EXTC_R2D_C_P0.311––
USB3_EXTD_D2R_N0.322––
USB3_EXTD_D2R_P0.322––
USB3_EXTD_R2D_C_N0.313––
USB3_EXTD_R2D_C_P0.314––
USBC_A_D2R_CR_N<1>_CWROL––
USBC_A_D2R_CR_N<1>_CXTOL––
USBC_A_D2R_CR_N<2>_CWROL––
USBC_A_D2R_CR_N<2>_CXTOL––
USBC_A_D2R_CR_P<1>_CWROL––
USBC_A_D2R_CR_P<1>_CXTOL––
USBC_A_D2R_CR_P<2>_CWROL––
USBC_A_D2R_CR_P<2>_CXTOL––
USBC_A_R2D_N<1>_CWROL––
USBC_A_R2D_N<1>_CXTOL––
USBC_A_R2D_N<2>_CWROL––
USBC_A_R2D_N<2>_CXTOL––
USBC_A_R2D_P<1>_CWROL––
USBC_A_R2D_P<1>_CXTOL––
USBC_A_R2D_P<2>_CWROL––
USBC_A_R2D_P<2>_CXTOL––
USBC_AUXLSX_N_R0.712––
USBC_AUXLSX_N_T0.716––
USBC_AUXLSX_N_W0.715––
USBC_AUXLSX_N_X0.719––
USBC_AUXLSX_P_R0.701––
USBC_AUXLSX_P_T0.705––
USBC_AUXLSX_P_W0.708––
USBC_AUXLSX_P_X0.712––
USBC_B_D2R_CR_N<1>_CWROL––
USBC_B_D2R_CR_N<1>_CXTOL––
USBC_B_D2R_CR_N<2>_CWROL––
USBC_B_D2R_CR_N<2>_CXTOL––
USBC_B_D2R_CR_P<1>_CWROL––
USBC_B_D2R_CR_P<1>_CXTOL––
USBC_B_D2R_CR_P<2>_CWROL––
USBC_B_D2R_CR_P<2>_CXTOL––
USBC_B_R2D_N<1>_CWROL––
USBC_B_R2D_N<1>_CXTOL––
USBC_B_R2D_N<2>_CWROL––
USBC_B_R2D_N<2>_CXTOL––
USBC_B_R2D_P<1>_CWROL––
USBC_B_R2D_P<1>_CXTOL––
USBC_B_R2D_P<2>_CWROL––
USBC_B_R2D_P<2>_CXTOL––
USBC_HSR_AUXCH_C_N0.333––
USBC_HSR_AUXCH_C_P0.331––
USBC_HST_AUXCH_C_N0.333––
USBC_HST_AUXCH_C_P0.333––
USBC_HSW_AUXCH_C_N0.334––
USBC_HSW_AUXCH_C_P0.335––
USBC_HSX_AUXCH_C_N0.333––
USBC_HSX_AUXCH_C_P0.331––
USBC_R_CC10.583––
USBC_R_CC20.583––
USBC_R_RESET_L0.690––
USBC_R_RST_L0.674––
USBC_R_SBU10.652––
USBC_R_SBU20.651––
USBC_R_USB_BOT_N0.765––
USBC_R_USB_BOT_P0.765––
USBC_R_USB_TOP_N0.765––
USBC_R_USB_TOP_P0.765––
USBC_T_CC10.579––
USBC_T_CC20.580––
USBC_T_RESET_L0.660––
USBC_T_SBU10.664––
USBC_T_SBU20.655––
USBC_T_USB_BOT_N0.760––
USBC_T_USB_BOT_P0.760––
USBC_T_USB_TOP_N0.760––
USBC_T_USB_TOP_P0.760––
USBC_W_CC10.565––
USBC_W_CC20.564––
USBC_W_RESET_L0.652––
USBC_W_SBU10.654––
USBC_W_SBU20.654––
USBC_W_USB_BOT_N0.765––
USBC_W_USB_BOT_P0.765––
USBC_W_USB_TOP_N0.765––
USBC_W_USB_TOP_P0.765––
USBC_X_CC10.585––
USBC_X_CC20.586––
USBC_X_RESET_L0.675––
USBC_X_RST_L0.675––
USBC_X_SBU10.656––
USBC_X_SBU20.663––
USBC_X_USB_BOT_N0.764––
USBC_X_USB_BOT_P0.765––
USBC_X_USB_TOP_N0.765––
USBC_X_USB_TOP_P0.765––
UVP_DIS_L0.571––
VCCIN_AUX_PGOOD0.676––
VCCINAUX_PROG1OL––
VCCINAUX_PROG2OL––
VCCINAUX1_AGND0.000––
VCCINAUX1_BOOT_RC0.609––
VCCINAUX1_DRVH1.000––
VCCINAUX1_DRVH_R1.000––
VCCINAUX1_DRVL0.662––
VCCINAUX1_DRVL_R0.662––
VCCINAUX1_EN_R0.453––
VCCINAUX1_FSEL0.759––
VCCINAUX1_LL0.3801.800–
VCCINAUX1_LL_SNUB0.380––
VCCINAUX1_OCSET0.607––
VCCINAUX1_R0.3801.800–
VCCINAUX1_RTN_DIV_R0.004––
VCCINAUX1_RTN_DIV_XW0.003––
VCCINAUX1_SENSE_DIV0.383––
VCCINAUX1_SENSE_DIV_R0.763––
VCCINAUX1_SENSE_DIV_XW0.431––
VCCINAUX1_SET00.779––
VCCINAUX1_SET10.769––
VCCINAUX1_SET1_ROL––
VCCINAUX1_SREF0.775––
VCCINAUX1_VBST0.605––
VCCINAUX1_VID00.537––
VCCINAUX1_VID10.536––
VCCINAUX1_VO0.607––
VCCST_EN_B0.593––
VCCST_EN_C0.594––
VCCST_PWRGD0.5431.000–
VCCST_PWRGD_R0.624––
WC_L0.708––
WIFI_SROM_ORG0.699––
WLAN_AUDIO_SYNC0.506––
WLAN_AUDIO_SYNC_R0.480––
WLAN_CONTEXT_A0.628––
WLAN_CONTEXT_B0.737––
WLAN_JTAG_SEL0.725––
WLAN_JTAG_TCK0.742––
WLAN_JTAG_TDI0.475––
WLAN_JTAG_TDO0.739––
WLAN_JTAG_TMS0.742––
WLAN_JTAG_TRST_L0.737––
WLAN_PWR_EN0.481––
WLAN_SROM_STRAP0.727––
XDP_CPU_PWRBTN_L0.752––
XDP_CPU_TCK0.050––
XDP_CPU_TDI0.155––
XDP_CPU_TDO0.141––
XDP_CPU_TMS0.154––
XDP_CPU_TRST_L0.234––
XDP_HOOK20.214––
XDP_HOOK30.868––
XDP_PCH_TMS0.156––
XDP_PCH_TRST_L0.235––
XDP_PM_RSMRST_L1.674––
XDP_PRESENT_CPU_L0.802––
XDP_PRESENT_L0.464––
XDP_PRESENT2_L0.800––
XDP_USB_EXTC_OC_L0.796––
ZQ<0>_10.369––
ZQ<0>_20.370––
ZQ<0>_30.372––
ZQ<0>_40.373––
ZQ<1>_10.368––
ZQ<1>_20.370––
ZQ<1>_30.371––
ZQ<1>_40.371––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01949?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01949: diode 0.510, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-01949?

OpenBoardData's known-good values for PP3V3_G3H on the 820-01949: diode 0.450, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01949?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01949: diode 0.356, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01949 board?

Open your own 820-01949 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License