Apple laptop board · OpenBoardData

820-00045 known-good readings

Known-good readings for the Apple laptop board 820-00045: 789 nets, including 87 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 86 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00045.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 87 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 18

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V3_G3H0.39––
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail, judged from its name: the G3H suffix marks it as present whenever power is connected, before the board is switched on. The archive lists a known-good diode reading of 0.39 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.39, or a voltage that is missing or well off 3.3 V, usually points to a fault on that rail or its source rather than to the parts it feeds. Readings vary with board state, so treat 0.39 as a guide and compare against a matching rail or a known-good board where possible.

PP3V3_G3H_KBD_F0.39––
AI: what PP3V3_G3H_KBD_F is and how to check it

PP3V3_G3H_KBD_F is a 3.3 V always-on rail (G3H, from the name) feeding the keyboard section. The only known-good reading here is a diode value of 0.39 to ground; no voltage or resistance value is recorded for this rail.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.39.
  • Then power the board and measure the DC voltage on the rail; a healthy always-on rail should sit near 3.3 V, though that figure is general and not from this board's data.
  • A diode reading far below 0.39 suggests a short or leaky part on the rail; far above suggests an open trace or missing connection. Either way, confirm with a second measurement before replacing anything.
PP3V3_G3H_RTC_REG_R0.403––
AI: what PP3V3_G3H_RTC_REG_R is and how to check it

PP3V3_G3H_RTC_REG_R is an always-on 3.3 V rail, judged from its name: G3H means it should be present whenever the board has power, and RTC_REG suggests it feeds the real-time clock and its regulator. The archived reading for it is a diode value of 0.403 to ground; there is no known-good voltage here. Check it unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage on the rail. A diode reading far from 0.403 usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PP3V3_G3H_T0.400––
AI: what PP3V3_G3H_T is and how to check it

PP3V3_G3H_T is the always-on 3.3 V rail, a startup-stage supply that should be present whenever the board has power (from the name, G3H means always on). The only known-good reading here is a diode value of 0.400 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.400 usually points to a short or leak on the rail, while a missing voltage with a normal diode reading points more toward the supply that creates it. These readings are community guides and vary with board state, so treat a small difference as normal.

PP5V_G3H_LDO0.47––
AI: what PP5V_G3H_LDO is and how to check it

PP5V_G3H_LDO is a 5 V always-on rail; the G3H part of the name indicates it is up whenever the board has power, and LDO suggests it comes from a small linear regulator rather than a switching supply. The archive lists one known-good reading: diode 0.47 to ground, with no condition noted. Check it with the board unpowered in diode mode, black probe on ground, red on the rail, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a known-good board of the same model. A diode reading far from 0.47 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_G3S0.382––
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V rail; the G3S suffix marks it as an always-on startup rail, from its name (general naming convention, not board-specific data). The archive lists one known-good reading: diode mode 0.382 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.382 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PPBUS_G3H0.398––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the G3H suffix, from the name, marks it as an always-on rail. The archive lists one known-good diode reading of 0.398 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from PPBUS_G3H to ground, then measure its voltage with power applied and compare against a known-good board. A diode reading far from 0.398 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.

PPBUS_G3H_SSD0_SNS0.398––
AI: what PPBUS_G3H_SSD0_SNS is and how to check it

PPBUS_G3H_SSD0_SNS is a sense line on the main PPBUS rail feeding the SSD, judged from its name; the G3H part means it is always-on whenever the board has power. The only known-good reading here is a diode value of 0.398 to ground, with no condition noted, and there is no known-good voltage reading for this net. Check it unpowered in diode mode to ground, then measure the voltage with power applied and compare against the main PPBUS rail. A diode reading far from 0.398 usually points to a short or a leaky component on that sense line, but one reading alone doesn't confirm a bad part.

PPBUS_G3H_TPAD_FLT0.46––
AI: what PPBUS_G3H_TPAD_FLT is and how to check it

PPBUS_G3H_TPAD_FLT is a filtered branch of the main PPBUS rail feeding the trackpad, judging by the name (G3H = always-on, TPAD = trackpad, FLT = filtered). The only known-good reading here is a diode value of 0.46; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with the 0.46 guide.
  • Then power the board and measure the DC voltage on the rail; without a known-good voltage, compare against the main PPBUS rail it derives from.
  • A diode reading far below 0.46 usually suggests a short or leaky part on the rail; a much higher or open reading points to a broken trace or missing feed.
PPBUS_G3H_TPAD_FUSED0.46––
AI: what PPBUS_G3H_TPAD_FUSED is and how to check it

PPBUS_G3H_TPAD_FUSED is a fused branch of the main PPBUS rail feeding the trackpad, and the G3H in its name indicates it is always-on. The only known-good reading here is a diode value of 0.46; no known-good voltage or resistance reading is recorded. Check it with the board unpowered in diode mode from the net to ground, then power the board and measure the voltage on it. A diode reading far from 0.46 usually points to a short or a leaky part on that branch, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything.

PPDCIN_G3H0.54––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail, judging from the name; on this board it's the DC-in feed present whenever power is connected. The archive lists a diode reading of 0.54 to ground for this net, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then measure the voltage with the charger connected. A diode reading far below 0.54 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken feed path. Voltage behaviour on this rail isn't documented here, so compare against a known-good board of the same model.

PPDCIN_G3H_CHGR0.534––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in the name indicates it is always-on, present whenever the charger is connected. The only known-good reading here is a diode value of 0.534 to ground, with no condition listed, and there is no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then with the charger connected measure the DC voltage on it. A diode reading well below 0.534 suggests a short or leaky part on the rail; a reading far above it suggests an open path back toward the input. This is a guide from community readings, not a confirmed value, and no voltage reference is available for comparison.

PPVBAT_G3H_CHGR_R0.400––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name indicates it is always on when power is present. The only known-good reading here is a diode value of 0.400 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode, red probe on the rail and black on ground, then apply power and measure the voltage. A diode reading far from 0.400 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PPVBAT_G3H_CHGR_REG0.399––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side battery rail; the G3H in the name indicates it is always-on, and CHGR points to the charger circuit (this is from the name, not from board data). The only known-good figure here is a diode reading of 0.399 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage on the same point. A diode reading far below 0.399 usually suggests a short or a leaky part on the rail, while a much higher or open reading points to a broken connection or missing component. Treat the 0.399 as a community guide only, since readings vary with board state, and confirm any suspect part with a second measurement before replacing it.

PPVBAT_G3H_CONN0.64––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judging from the name (G3H means always on). The archive lists a diode reading of 0.64 to ground for this net; no voltage or resistance known-good value is recorded here. Check it with the board unpowered and battery disconnected, meter in diode mode, black probe on ground and red on the net, then compare the voltage with power applied. A reading far from 0.64 in diode mode usually points to a short or an open on that rail or its connector, but one reading alone doesn't confirm a bad part.

PPVIN_G3H_P3V3G3H0.52––
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H is a 3.3 V always-on rail, judged from its name: "P3V3" is the 3.3 V output and "G3H" means it's present whenever the board has power. The only known-good reading in the archive is a diode value of 0.52 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on the net and black on ground, then power the board and measure the voltage at the same point. A diode reading far below 0.52 usually points to a short or a failing part on the rail; a voltage that's missing or wrong with a normal diode reading points more to the supply feeding it.

PPVIN_G3H_TPAD_FUSE0.398––
AI: what PPVIN_G3H_TPAD_FUSE is and how to check it

PPVIN_G3H_TPAD_FUSE is a trackpad input rail that should be present whenever the charger is connected, based on the G3H "always on" naming. The only known-good reading here is a diode value of 0.398 to ground; no known-good voltage or resistance reading is recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.398 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PPVRTC_G3H0.48––
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is an always-on rail (the "G3H" suffix is from the name, meaning it stays up whenever power is present). The only known-good figure here is a diode reading of 0.48 to ground, with no condition noted; no known-good voltage is listed. Check it unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.48 usually points to a short or a leaky part on the rail; a much higher or open reading suggests a broken connection. No known-good voltage is available here, so compare against a matching always-on rail or a known-good board.

S5 and SUS: standby 8

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.51––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC (820-00045) — a 1.2 V standby rail feeding the SMC, from the name (S5/SUS = standby, VDDC = supply).

  • Known-good: diode 0.51 to ground. No known-good voltage reading here.
  • Check unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far below 0.51 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PP1V05_SUS0.350––
AI: what PP1V05_SUS is and how to check it

PP1V05_SUS is a 1.05 V standby rail, judged from its name (SUS = standby, S5 stage). The only known-good reading in the archive is a diode value of 0.350 to ground, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.350 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a matching standby net or a known-good board before replacing anything.

PP1V05_SUS_PCH_VCCAOSCSUS0.34––
AI: what PP1V05_SUS_PCH_VCCAOSCSUS is and how to check it
  • What it is: From the name, a 1.05 V standby (SUS) rail feeding the PCH's VCC and oscillator supply; the S5/SUS naming puts it in the standby stage.
  • Known-good reading: diode 0.34 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a missing voltage with a normal diode reading points upstream to the standby regulator or its enable. Confirm with a second measurement before replacing anything.
PP3V0_S5_AVREF_SMC0.58––
AI: what PP3V0_S5_AVREF_SMC is and how to check it

PP3V0_S5_AVREF_SMC — from its name, a 3.0 V standby (S5) reference rail feeding the SMC. The only known-good reading here is a diode value of 0.58; no known-good voltage or resistance is listed.

  • Check with the board unpowered: diode mode, black probe to ground, red to the rail. Around 0.58 is the guide; a much lower value suggests a short on the rail, a much higher one an open.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded here, so compare against a known-good board or the same net on a matching board.
  • A reading far off the diode guide usually points to a shorted component on that rail or a damaged feed; confirm with the voltage measurement before replacing anything.
PP3V3_S50.390––
AI: what PP3V3_S5 is and how to check it
  • PP3V3_S5 is the 3.3 V standby rail; the "S5" in its name marks it as a standby-stage rail that should be present before the board fully powers on.
  • Known-good: diode reading 0.390 to ground (from the readings archive). No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.390 usually points to a short or a leaky part on that rail; confirm with a voltage check before replacing anything.
PP3V3_S5_SMC_VDDA0.38––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply; the S5 and SUS parts of the name indicate it belongs to the standby stage. The only known-good reading here is a diode value of 0.38 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from 0.38 usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a fault.

PP3V3_SUS0.315––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail, judged from its name (SUS = suspend/standby), so it should be present before the board fully powers on. The only known-good reading here is a diode value of 0.315 to ground; no known-good voltage is listed. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.315 suggests a short or leaky load on the rail; far above it suggests an open path. These readings are community guides and vary with board state, so compare against a matching net or a known-good board before condemning a part.

PPBUS_S5_HS_COMPUTING_ISNS0.460––
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From its name, PPBUS_S5_HS_COMPUTING_ISNS is a sense (ISNS) line on the PPBUS rail in the S5 standby stage, tied to the high-side computing supply. The exact parts on it aren't known here.
  • Known-good reading: diode 0.460 to ground, from the community archive; treat it as a guide, not a guarantee.
  • How to check: power off and unplug, then measure diode mode from the net to ground. Then power up and measure the voltage on it.
  • No known-good voltage is listed for this net, so compare against a matching net or a known-good board.
  • If a diode reading is far off (near 0 or open), that usually points to a shorted or open component on the net, but confirm with voltage and resistance before replacing anything.

S4 8

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V05_S4SW0.390––
AI: what PP1V05_S4SW is and how to check it
  • PP1V05_S4SW is a 1.05 V rail in the S4 (suspend-to-RAM) power state, from its name. The S4 stage means it comes up during sleep/suspend sequencing rather than full-on.
  • Known-good from the archive: diode-to-ground 0.390 (no condition recorded). No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.390 usually points to a short or a leaky part on that rail; a correct diode reading with no voltage points more to the enable or upstream supply. Neither is confirmed from one reading.
PP3V3_S40.39––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail that comes up at the S4 stage of the power sequence, judged from its name; the board data has no part list, so which components sit on it isn't known.

  • Known-good reading: diode 0.39 to ground (community value, a guide only; no condition recorded).
  • Check it with the board unpowered in diode mode, red probe on ground, black on the rail; then power up and measure the voltage, expecting about 3.3 V.
  • No known-good voltage reading here, so compare against a matching S4 rail or a known-good board.
  • A diode reading far below 0.39 usually points to a short or leaky part on the rail; far above it suggests an open trace or missing connection.
PP3V3_S4_TPAD_F0.40––
AI: what PP3V3_S4_TPAD_F is and how to check it

PP3V3_S4_TPAD_F is a 3.3 V rail feeding the trackpad, and the S4 in its name places it in the S4 startup stage (both from the name).

  • Known-good: diode reading 0.40 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the voltage.
  • A diode reading far from 0.40 usually points to a short or a leaky part on that rail; a missing or low voltage with power on points to the rail not coming up or being loaded down.
PP5V_S40.41––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, both from its name. The archive lists a known-good diode reading of 0.41 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP5V_S4 to ground and compare with 0.41; then power up and check the voltage. A diode reading far below 0.41 suggests a short or leaky load on the rail, while a missing voltage with a normal diode reading points upstream to the rail's enable or source. These readings are community guides and vary with board state, so treat a small difference as normal.

PP5V_S4_TPAD_F0.45––
AI: what PP5V_S4_TPAD_F is and how to check it

PP5V_S4_TPAD_F is a 5 V rail for the trackpad, enabled at the S4 stage of the power sequence (from the name). The only known-good figure here is a diode reading of 0.45 to ground, with the board unpowered. Check it in diode mode with power off, then measure the voltage with the board powered and the rail enabled. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.45 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm it.

PP5V1_S4SW0.480––
AI: what PP5V1_S4SW is and how to check it

PP5V1_S4SW is a 5.1 V rail in the S4 startup stage, judging by its name. The only known-good reading here is a diode value of 0.480; there's no known-good voltage or resistance reading for it.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.480.
  • Then power the board and measure the voltage on the rail; the data gives no expected voltage, so compare against a known-good board or the same rail on a matching circuit.
  • A diode reading far below 0.480 usually points to a short or a leaky part on the rail; a much higher one can mean an open path.
PP5V1_S4SW_CC10.517––
AI: what PP5V1_S4SW_CC1 is and how to check it
  • What it is: PP5V1_S4SW_CC1 is a 5.1 V rail in the S4 startup stage, both from its name. The data doesn't say which parts sit on it.
  • Known-good reading: diode 0.517 to ground, no condition listed. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power up and measure the voltage.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. Confirm with the voltage before replacing anything.
PP5V1_S4SW_CC20.518––
AI: what PP5V1_S4SW_CC2 is and how to check it

PP5V1_S4SW_CC2 is a 5.1 V rail, from its name: the S4 startup stage, a switched supply (SW) for CC2. The only known-good reading here is a diode value of 0.518 to ground; no known-good voltage or resistance is recorded.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.518.
  • Then power the board and measure the voltage on the rail.
  • A diode reading far from 0.518 usually points to a short or a leaky part on that rail; a missing or low voltage under power points to the rail not being enabled or its source failing.

These readings are community guides and vary with board state, so confirm against a known-good board where possible.

S3: memory 8

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S30.275–128.000R
AI: what PP1V2_S3 is and how to check it
  • What it is: PP1V2_S3 is a 1.2 V rail in the S3 (memory) startup stage, judged from the rail name. The archive has no board file, so which parts sit on it isn't known.
  • Known-good readings (community guide): diode 0.275 to ground, resistance 128.000R. No known-good powered voltage is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then resistance; then apply power and measure the rail voltage.
  • If readings are far off: a much lower diode or resistance usually points to a short or a failing load on the rail; a much higher one can mean an open feed. Confirm with a second measurement before replacing anything.
PP1V2_S3_CPUDDR0.069––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is a 1.2 V supply for the CPU's DDR memory, going by its name (1V2 = 1.2 V, S3 = memory stage, CPUDDR = CPU DDR). The only known-good reading here is a diode value of 0.069 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode, black probe on ground, red on the rail, and compare with the 0.069 guide.
  • Then power the board and measure the voltage on the rail; expect about 1.2 V from the name, but that is general, not a recorded value for this board.
  • A diode reading far below 0.069 suggests a short or a leaky part on the rail; far above it suggests an open connection or a missing part.
PP1V2_S3_REG_R0.071––
AI: what PP1V2_S3_REG_R is and how to check it
  • What it is: From its name, PP1V2_S3_REG_R is a 1.2 V regulated rail in the S3 (memory) startup stage. The parts on it aren't known here.
  • Known-good reading: Diode mode to ground, 0.071 (community archive, guide only). No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 1.2 V from the name.
  • If far off: A diode reading well below 0.071 suggests a short or leaky load on the rail; a missing voltage points to the regulator or its enable. Confirm with a second measurement before replacing anything.
PP1V8_S30.380––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix comes from its name and marks it as a memory-stage rail in the startup sequence. The only known-good reading here is diode 0.380 to ground, with no condition noted; there is no known-good voltage reading in this data.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied.
  • A diode reading far from 0.380 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part.
  • No known-good voltage value is available here, so compare the powered voltage against the rail's nominal 1.8 V and a matching rail on a known-good board.
PP2V5_S30.420––
AI: what PP2V5_S3 is and how to check it
  • PP2V5_S3 is a 2.5 V rail; the "S3" in the name marks it as a memory-stage rail (from the name, not from a schematic).
  • Known-good: diode to ground 0.420. No known-good voltage reading here.
  • Check with the board unpowered: meter in diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.420 usually points to a short or a leaky part on that rail; confirm with a voltage check before replacing anything.
PPVREF_S3_MEM_VREFCA0.45––
AI: what PPVREF_S3_MEM_VREFCA is and how to check it

PPVREF_S3_MEM_VREFCA is a memory reference voltage rail; the S3 and MEM parts of the name indicate it belongs to the S3 (memory) startup stage, and VREFCA is a reference for the memory's address/command side. The only known-good reading here is a diode value of 0.45 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. There is no known-good voltage reading for this rail, so compare against a matching reference net or a known-good board. A diode reading far from 0.45 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.

PPVREF_S3_MEM_VREFDQ_A0.52––
AI: what PPVREF_S3_MEM_VREFDQ_A is and how to check it

PPVREF_S3_MEM_VREFDQ_A — reference note

  • From its name, this is an S3-state memory reference voltage (VREFDQ) for the memory subsystem; the S3 prefix places it in the memory stage of startup.
  • Known-good from the readings archive: diode mode to ground 0.52. That is the only known-good value recorded here; there is no known-good voltage reading for this rail.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.52. Then power the board and measure the DC voltage on the rail.
  • A diode reading far below 0.52 usually points to a short or a leaky load on the rail; far above it can mean an open path. Confirm with a voltage measurement under power before suspecting any part.
PPVREF_S3_MEM_VREFDQ_B0.27––
AI: what PPVREF_S3_MEM_VREFDQ_B is and how to check it
  • PPVREF_S3_MEM_VREFDQ_B is a memory reference rail: the name indicates an S3 (memory) stage and a DDR VREFDQ reference for the memory data lines. That meaning is from the name, not from a schematic.
  • Known-good: diode-to-ground 0.27 (community reading, a guide only). No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.27 usually points to a short or a faulty part on that net, but confirm with the voltage before replacing anything.

S0: running 45

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V95_S0_CPUVCCIO_REG_R0.038–53.000R
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it

PP0V95_S0_CPUVCCIO_REG_R is a 0.95 V rail feeding CPU VCCIO, from the name; the S0 suffix means it's up in the running state. The archive lists diode 0.038 and resistance 53.000R for it, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from these usually points to a short or leak on the rail or its load rather than the regulator itself, but that's a likely cause, not confirmed. No known-good voltage reading is recorded here.

PP1V1_S0SW_SSD0.190––
AI: what PP1V1_S0SW_SSD is and how to check it

PP1V1_S0SW_SSD is a 1.1 V rail; the S0 in its name indicates it belongs to the running (S0) power state, and SSD suggests it feeds the SSD section. The only known-good reading in the archive is a diode value of 0.190 to ground, with no condition recorded and no known-good voltage here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.190 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP1V2_S0SW_SSD_COLD0.300––
AI: what PP1V2_S0SW_SSD_COLD is and how to check it

PP1V2_S0SW_SSD_COLD — from the name: a 1.2 V rail (PP1V2) that is switched (SW), in the S0 running state, feeding the SSD in its cold state. The S0 part means it should only be present once the board is fully on, not in standby.

  • Known-good reading: diode 0.300 to ground, from the readings archive. That is a guide, not a spec.
  • How to check: power off and unplug, then diode mode from the rail to ground; it should sit near 0.300. Then power on and measure the voltage — expect about 1.2 V once the board is in S0. No known-good voltage reading is recorded here.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; a much higher one suggests an open path. A missing voltage with a good diode reading points upstream, to the enable or switch that creates it.
PP1V2_S0SW_SSD_HOT0.340––
AI: what PP1V2_S0SW_SSD_HOT is and how to check it

PP1V2_S0SW_SSD_HOT is a 1.2 V rail feeding the SSD section, from its name; the S0 part means it comes up in the running state, and HOT suggests it stays on in sleep. The only known-good reading here is a diode value of 0.340 to ground, with no condition recorded; there's no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.340 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP1V05_S00.190––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail; the S0 suffix, from the name, marks it as a running-state supply rather than a standby rail. The only known-good figure here is a diode reading of 0.190 to ground, with no condition recorded, and there is no known-good voltage reading for it. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.190 usually points to a short or a leaky load on the rail, while a correct diode reading with no voltage points back toward the rail's supply or its enable. Treat the 0.190 as a guide only, since community readings vary with board state.

PP1V5_S00.360––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the S0 suffix, from the name, means it belongs to the running (S0) state rather than standby. The only known-good reading here is a diode value of 0.360 to ground, with no condition recorded; no known-good voltage reading is available. Check it unpowered in diode mode from PP1V5_S0 to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.360 suggests a short or a leaky load on the rail; a far higher or open reading points to a broken connection. Confirm with the voltage measurement before suspecting any part.

PP1V05_S0_PCH_VCC_ICC0.19––
AI: what PP1V05_S0_PCH_VCC_ICC is and how to check it

PP1V05_S0_PCH_VCC_ICC is a 1.05 V rail for the PCH, and the S0 in its name indicates it belongs to the running (S0) state.

  • Known-good: diode reading 0.19 to ground, from the readings archive. No known-good voltage reading here.
  • Check it with the board unpowered: multimeter in diode mode, black probe on ground, red on the rail.
  • Then power the board and measure the voltage on the rail; expect roughly 1.05 V, though that figure comes from the rail name, not from a recorded reading.
  • A diode reading far from 0.19 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part; compare with a matching rail or a known-good board before replacing anything.
PP1V05_S0_PCH_VCC_ICC_R0.190––
AI: what PP1V05_S0_PCH_VCC_ICC_R is and how to check it

PP1V05_S0_PCH_VCC_ICC_R is a 1.05 V rail; the S0 in its name indicates it belongs to the running (S0) power state, and the PCH_VCC_ICC part suggests it feeds the PCH. The only known-good figure here is a diode reading of 0.190 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.190 usually points to a short or a leaky part on the rail, but a single reading isn't proof — compare against a matching rail or a known-good board before condemning anything.
  • No voltage value is recorded here, so judge the powered reading against what the rail's name implies (about 1.05 V) and against a known-good board.
PP1V05_S0_PCH_VCCACLKPLL0.190––
AI: what PP1V05_S0_PCH_VCCACLKPLL is and how to check it

PP1V05_S0_PCH_VCCACLKPLL is a 1.05 V rail for the PCH clock/PLL supply, and the S0 in its name indicates it belongs to the running state. The only known-good figure here is a diode reading of 0.190 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode to ground, then power up and measure the voltage. A diode reading far from 0.190 usually points to a short or a damaged part on that rail, but confirm with a voltage check before replacing anything.

PP1V05_S0_PCH_VCCACLKPLL_R0.190––
AI: what PP1V05_S0_PCH_VCCACLKPLL_R is and how to check it
  • What it is: From the name, PP1V05_S0_PCH_VCCACLKPLL_R is a 1.05 V rail (PP1V05) that is on in the S0 running state (S0) and feeds the PCH's ACLK PLL supply (PCH_VCCACLKPLL). It's a small, local PLL rail, not a main power rail.
  • Known-good reading: diode 0.190 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail; no known-good voltage is recorded, so compare against a known-good board of the same model.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing part. Confirm with the voltage measurement before replacing anything.
PP1V05_S0_PCH_VCCAPLL_OPI0.190––
AI: what PP1V05_S0_PCH_VCCAPLL_OPI is and how to check it
  • What it is: From its name, a 1.05 V S0 (running-state) rail feeding the PCH's VCCAPLL OPI supply. It's a low-voltage rail, so treat it as sensitive.
  • Known-good reading: Diode mode to ground 0.190 (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.190. Then power up and measure the DC voltage on the rail, which should sit near 1.05 V.
  • If it's far off: A diode reading well below 0.190 suggests a short or leaky load on the rail; a much higher or open reading suggests a broken feed. Confirm with the powered voltage before replacing anything.
PP1V05_S0SW_PCH_PCIE0.300––
AI: what PP1V05_S0SW_PCH_PCIE is and how to check it
  • PP1V05_S0SW_PCH_PCIE is a 1.05 V rail, from its name: the S0 (running) switched supply feeding the PCH's PCIe section. The name is the only description available here; which parts sit on the net isn't known.
  • Known-good: diode reading 0.300 in the readings archive, no condition recorded. No known-good voltage or resistance reading here.
  • Check: board unpowered, diode mode, red probe to ground and black to the rail; then power up and measure the voltage at the rail.
  • Far from 0.300 in diode mode usually points to a short or a leaky part on the rail; a correct diode reading but no voltage points upstream, at the rail's enable or its source supply. A single reading isn't proof a part is bad.
PP1V05_S0SW_PCH_SATA0.325––
AI: what PP1V05_S0SW_PCH_SATA is and how to check it

PP1V05_S0SW_PCH_SATA is a 1.05 V rail, from its name: the S0 state means it belongs to the running (fully on) power state, and the PCH SATA part suggests it feeds the chipset's SATA section. The only known-good reading here is a diode value of 0.325 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.325 usually points to a short or a leaky load on the rail, but a single reading isn't proof a part is bad, so compare with a matching rail or a known-good board before replacing anything.

PP1V05_S0SW_PCH_USB30.320––
AI: what PP1V05_S0SW_PCH_USB3 is and how to check it
  • PP1V05_S0SW_PCH_USB3 is a 1.05 V rail, from its name, feeding the PCH USB3 section and switched on in the S0 (running) state.
  • Known-good: diode reading 0.320 to ground. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.320 suggests a short or leaky part on that rail; a missing voltage with a good diode reading points upstream to the rail's enable or supply.
PP1V05_S0SW_PCH_VCCSATA3PLL0.325––
AI: what PP1V05_S0SW_PCH_VCCSATA3PLL is and how to check it

PP1V05_S0SW_PCH_VCCSATA3PLL is a 1.05 V rail; from its name it supplies the PCH's SATA 3 PLL and runs in the S0 (running) state. The only known-good reading here is a diode value of 0.325 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.325 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad part.

PP1V05_S0SW_PCH_VCCUSB3PLL0.32––
PP1V8_S0_GPU0.233––
AI: what PP1V8_S0_GPU is and how to check it

PP1V8_S0_GPU is a 1.8 V rail for the GPU, from its name; the S0 suffix indicates it belongs to the running state. The archive lists a diode reading of 0.233 to ground for this rail; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.233 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP1V8_S0SW_SSD_COLD0.350––
AI: what PP1V8_S0SW_SSD_COLD is and how to check it

PP1V8_S0SW_SSD_COLD — a 1.8 V rail, from its name: the S0 (running) state, switched (SW), feeding the SSD, and "COLD" suggests it's the cold-side supply. It's a startup-stage rail, so it should come up once the board is in S0.

  • Known-good: diode 0.350 to ground (from the readings archive; community value, a guide only). No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 1.8 V.
  • Far from known-good: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open feed or a missing enable. Confirm with the voltage under power before replacing anything.
PP1V8_S0SW_SSD_HOT0.500––
AI: what PP1V8_S0SW_SSD_HOT is and how to check it

PP1V8_S0SW_SSD_HOT is a 1.8 V rail, from its name: the S0 state means it belongs to the running (on) power state, and SSD_HOT suggests it feeds the SSD section. The only known-good reading here is a diode value of 0.500 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.500.
  • Then power the board and measure the voltage; expect roughly 1.8 V from the name, but that is general, not a recorded value.

A diode reading far below 0.500 usually points to a short or a failing part on the rail; a much higher or open reading suggests a broken connection. A voltage well under 1.8 V with a normal diode reading points more toward the rail not being enabled or its supply missing. These are likely causes, not confirmed ones, so trace the enable and supply side before replacing anything.

PP2V5_S0SW_SSD0.44––
AI: what PP2V5_S0SW_SSD is and how to check it

PP2V5_S0SW_SSD is a 2.5 V rail, from its name: the "S0" suffix marks it as a running-state supply, and "SW" suggests a switched rail, likely feeding the SSD section.

  • Known-good reading in the archive: diode 0.44 (no condition recorded). No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running.
  • A diode reading far from 0.44 usually points to a short or a leaky part on that rail; a missing or low voltage under power points to the switch or its supply.
PP3V3_S00.350––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judging from its name. The archive lists a diode reading of 0.350 for it; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S0 to ground and compare with 0.350, then apply power and check the voltage. A diode reading far below 0.350 usually points to a short or a failing load on the rail, while a missing voltage with a normal diode reading points upstream to the regulator or its enable. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP3V3_S0_CPUTHMSNS_R0.39––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R is a 3.3 V S0 (running-state) rail; the name suggests it feeds the CPU thermal-sense circuit, though that's from the name only. Known-good: diode 0.39 to ground (no condition recorded); no known-good voltage reading here. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode reading far from 0.39 usually points to a short or a damaged component on that net, but confirm with a voltage check before replacing anything.

PP3V3_S0SW_LCD0.650––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a 3.3 V LCD-related rail; the S0 in the name indicates it belongs to the running (S0) state, and SW suggests it is switched. The only known-good reading here is a diode value of 0.650 to ground, with no condition noted, so treat it as a guide. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. No known-good voltage reading is available for this rail, so compare against a matching rail or a known-good board. A diode reading far from 0.650 usually points to a short or a leaky part on that rail, but confirm with the voltage measurement before replacing anything.

PP3V3_S0SW_S1X0.59––
AI: what PP3V3_S0SW_S1X is and how to check it

PP3V3_S0SW_S1X is a 3.3 V rail; from the name, "S0" means it belongs to the running state and "SW" suggests a switched rail. The only known-good reading here is diode mode 0.59 to ground, with no condition recorded; no voltage reading is known-good in this data. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode reading far from 0.59 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S0SW_SSD0.36––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a 3.3 V rail switched on in the S0 (running) state, feeding the SSD; that reading comes from the rail's name, not from a schematic. The archive lists one known-good reading: diode 0.36 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far below 0.36 suggests a short or leaky load on the rail; a far higher one suggests an open path, but one reading alone doesn't confirm a bad part.

PP5V_S00.430––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, judged from its name; it is a main running-state supply. The only known-good figure here is a diode reading of 0.430 to ground, with no condition recorded. Check it with the board unpowered in diode mode from PP5V_S0 to ground, then measure the voltage with the board powered and in S0. No known-good voltage reading here, so compare against a matching 5 V rail or a known-good board. A diode reading far below 0.430 usually points to a short or a failing load on the rail; a far higher or open reading points to a broken connection, but confirm with the voltage measurement before replacing anything.

PP5V_S0_ALSCAM_F0.430––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V rail that, from its name, runs in the S0 (running) state and feeds the ALS camera circuit. The only known-good reading here is a diode value of 0.430 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.430 usually points to a short or a leaky part on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S0_CPUVR_VDD0.44––
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD is a 5 V rail that, from its name, feeds the CPU voltage regulator's VDD supply and is active in the S0 (running) state. The only known-good reading here is a diode value of 0.44 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.44 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S0_KBD_F0.42––
AI: what PP5V_S0_KBD_F is and how to check it

PP5V_S0_KBD_F — reference note

  • From its name, this is a 5 V rail (PP5V) that is present in the S0 running state and feeds the keyboard circuit (KBD). It is a switched rail, so it should only appear once the board is fully on.
  • Known-good reading in the archive: diode mode to ground 0.42. That is the only value recorded here; there is no known-good voltage or resistance for this rail.
  • To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage at the rail. Compare the diode reading with 0.42.
  • A diode reading far below 0.42 suggests a short or a leaky load on the rail; far above it suggests an open path. A missing voltage with a normal diode reading points upstream, at the switch or enable that creates the rail, not at the rail itself.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PP5V_S0SW_LCD0.570––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is a switched 5 V rail feeding the LCD, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.570 to ground, with no condition recorded; no known-good voltage reading is available. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far below 0.570 usually points to a short or a leaky load on the rail, while a much higher reading can mean an open path; treat these as guides and confirm with a second measurement before replacing anything.

PPBUS_S0_LCDBKLT_FUSED0.46––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it

PPBUS_S0_LCDBKLT_FUSED is the fused backlight boost rail for the LCD, going by its name (PPBUS supply, S0 running state, LCD backlight, fused). The archive lists a known-good diode reading of 0.46 to ground, with no condition noted, and no known-good voltage or resistance reading here.

  • Check it unpowered in diode mode from the net to ground; a reading well below 0.46 suggests a short or leaky load on the rail, while a much higher or open reading points to a broken path or missing load.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded here, so compare against a known-good board of the same model.
  • A single off reading isn't proof of a bad part; confirm with a second measurement before replacing anything.
PPBUS_S0_LCDBKLT_PWR_SW0.44––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
  • What it is: From its name, PPBUS_S0_LCDBKLT_PWR_SW is the backlight power rail on the main power bus, switched, and active in the S0 (running) state. This is general reading of the name, not confirmed circuit detail.
  • Known-good reading: Diode 0.44 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.44. Then apply power and measure the rail voltage; there's no archived voltage to compare against, so compare with a known-good board or the same rail on a matching board.
  • If it's far off: A diode reading well below 0.44 suggests a short or leaky load on the rail; a much higher or open reading suggests a break in the path. A single reading isn't proof a part is bad, so confirm with the voltage measurement before replacing anything.
PPVCC_S0_CPU0.109––
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail, active in S0 (running), as the name indicates. The only known-good figure here is a diode reading of 0.109 to ground; no voltage reading is recorded for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.109 usually points to a short or a damaged component on that rail, but confirm with a second measurement before replacing anything.

PPVCC_S0_CPU_PH10.060–85.100R
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 is a CPU power rail; the "S0" in its name indicates the running state, and "PH1" suggests a phase of the CPU buck converter (from the name, not confirmed by board data). Known-good readings here are diode 0.060 and resistance 85.100R; no known-good voltage is listed. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far from 0.060 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PPVCC_S0_CPU_PH20.109–85.100R
AI: what PPVCC_S0_CPU_PH2 is and how to check it
  • What it is: PPVCC_S0_CPU_PH2 is a CPU power rail, from its name: VCC for the CPU, S0 meaning the running state, PH2 likely a phase of the CPU VRM. It's a high-current rail, so expect low ohms.
  • Known-good readings (community archive, guide only): diode 0.109 to ground, resistance 85.100R. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then resistance; then power on and measure the voltage on the rail.
  • If far off: a much lower diode or resistance reading usually points to a short on the rail (often a bad CPU or VRM phase); a much higher one to an open. Confirm with a second measurement before replacing anything.
PPVCCIO_S0_CPU0.039–52.600R
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU — the name indicates the CPU's S0 (running-state) I/O supply rail on the 820-00045.

  • Known-good readings from the archive: diode 0.039 and resistance 52.600R. These are community readings and vary with board state, so treat them as a guide.
  • To check: power off and unplug, then measure diode mode to ground on the rail. That low diode value is normal for a heavy CPU rail, so compare against the archive figure rather than expecting a high reading.
  • Then apply power and measure the rail voltage. No known-good voltage reading here, so compare with a known-good board or the rail's expected level.
  • A diode or resistance far below known-good usually points to a short or a failing component on the rail; a much higher resistance can mean an open trace or missing part. No parts list is available for this net, so trace it on the board before replacing anything.
PPVCOMP_S0_CPU0.15––
AI: what PPVCOMP_S0_CPU is and how to check it
  • What it is: PPVCOMP_S0_CPU is a CPU-related rail; the S0 suffix means "running" state, from the name. The data doesn't say which parts sit on it.
  • Known-good reading: diode 0.15 to ground, from the readings archive (community value, a guide only). No known-good voltage or resistance here.
  • How to check: power off and unplug, then diode mode from the net to ground; then power up and measure the voltage on it.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, but one reading isn't proof — compare with a known-good board before replacing anything.
PPVCORE_S0_GFX_PH11.000––
AI: what PPVCORE_S0_GFX_PH1 is and how to check it
  • What it is: From the name, PPVCORE_S0_GFX_PH1 is the graphics core power rail (VCORE, GFX), in the S0 running state, phase 1 (PH1) of a multiphase supply. The board data only gives the net name and stage, not which parts sit on it.
  • Known-good reading: diode 1.000 in the readings archive. That's a community figure and a guide, not a spec; no known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground. Then power on and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a bad phase component; a correct diode but no voltage points to the supply not being enabled or a phase not switching. Confirm with a second measurement before replacing anything.
PPVCORE_S0_GFX_PH21.000––
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 is a graphics core power rail: the name indicates processor core supply (VCORE) for the graphics block (GFX), in the S0 running state, and PH2 suggests a switching-regulator phase. The only known-good figure here is a diode reading of 1.000 to ground, with no condition recorded; no known-good voltage reading is available. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on the rail with the board powered and running. A diode reading far from 1.000, or a voltage that is absent or wrong in S0, usually points to a problem on that rail or its regulator rather than proving a particular part bad.

PPVCORE_S0_GFX_PH31.000–1.800R
AI: what PPVCORE_S0_GFX_PH3 is and how to check it

PPVCORE_S0_GFX_PH3 is a graphics core power rail; the name suggests VCORE for the GPU, and the S0 suffix marks it as a running-state rail (from the name). Known-good readings here are diode 1.000 and resistance 1.800R, with no condition recorded. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied; no known-good voltage reading here. A diode reading far below 1.000 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVDDCI_S0_GPU0.017––
AI: what PPVDDCI_S0_GPU is and how to check it

PPVDDCI_S0_GPU is a GPU core supply rail; the S0 in the name indicates it is active in the running state. The only known-good reading here is a diode value of 0.017 to ground, with no condition recorded. Check it unpowered in diode mode, red probe on ground and black on the rail, then confirm the voltage with the board powered and running. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.017 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a fault.

PPVIN_S0_CPUVR_VIN0.46––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it
  • What it is: From the name, PPVIN_S0_CPUVR_VIN is the input supply to the CPU voltage-regulator section, active in the S0 (running) state. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.46 to ground (archive value, a guide only; board state varies). No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on that rail; a much higher one to an open feed. Confirm with a voltage check before replacing anything.
PPVIN_S0SW_LCDBKLT0.852––
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail for the LCD, from its name: the "S0" state means it's present while the board is running, and "LCDBKLT" points to the display backlight circuit. The only known-good value here is a diode reading of 0.852 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.852.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is listed, so compare against a matching rail on a known-good board of the same model.
  • A diode reading far below 0.852 usually suggests a short or a leaky component on the rail; a far higher or open reading points to a broken connection or missing supply.
PPVOUT_S0_LCDBKLT1.158––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight output rail; the S0 in the name indicates it belongs to the running (S0) power state, and LCDBKLT points to the backlight boost output.

  • Known-good reading in the archive: diode mode to ground 1.158. That is the only known-good value recorded here; no voltage reading is listed.
  • Check it with the board unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 1.158.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is recorded, so compare against a known-good board or the panel's backlight spec.
  • A diode reading far below 1.158 usually suggests a short or leaky part on the rail; a reading far above can mean an open path. Confirm with voltage and resistance checks before replacing anything.
PPVOUT_S0_PCH_DCPRTC0.70––
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it
  • What it is: From the name, PPVOUT_S0_PCH_DCPRTC is a power output rail (PPVOUT) active in the S0 running state, feeding the PCH's DCPRTC domain. The board data only gives the name and startup stage, not the parts on the net.
  • Known-good reading: diode 0.70 to ground, from the community archive; treat it as a guide that varies with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage. No known-good voltage reading here, so compare against a matching rail or a known-good board.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open. Confirm with voltage before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
AGND_PMIC0.000––
ALL_SYS_PWRGD0.470––
ANI_VREF0.480––
AP_CLKREQ_L0.47––
AP_PCIE_DEV_WAKE0.55––
AP_PCIE_WAKE_L0.52––
AP_RESET_L0.57––
AP_S0IX_WAKE_L0.57––
AP_S0IX_WAKE_SEL0.51––
AUD_LRCLK_A0.53––
AUD_LRCLK_LEFT10.534––
AUD_LRCLK_LEFT20.535––
AUD_LRCLK_RIGHT20.530––
AUD_PWR_EN0.66––
AUD_SCLK_A0.580––
AUD_SCLK_RIGHT20.570––
AUD_SCLKA_LEFT10.576––
AUD_SCLKA_LEFT20.576––
AUD_SDOUT_A0.530––
AUD_SDOUT_LEFT10.534––
AUD_SDOUT_LEFT20.534––
AUD_SDOUT_RIGHT10.530––
AUD_SDOUT_RIGHT20.530––
AUD_SPKRAMP_MODE0.550––
AUD_SPKRAMP_MODE_LEFT20.547––
AUD_SPKRAMP_MODE_RIGHT10.560––
AUD_SPKRAMP_MODE_RIGHT20.550––
BBPD_CON_DET_L0.58––
BBPD_MISO_LS1V10.12––
BBPD_PD_EN0.54––
BBPD_PD_SEL_CC20.60––
BBPD_RPD_EN0.60––
BBPD_RX_L_TX_H0.60––
BBPD_SPI_MISO0.50––
BBPD_SPI_MISO_BUF0.34––
BBPD_SPI_MOSI0.63––
BBPD_VCONN_EN0.587––
BBPD_VCONN1_EN0.68––
BBPD_VCONN2_EN0.68––
BKL_FB0.63––
BKLT_EN_R0.52––
BKLT_SCL_R0.53––
BKLT_SD0.60––
BKLT_SDA_R0.53––
BT_SPI_CLK0.589––
BT_SPI_CS_L0.678––
BT_SPI_MOSI0.585––
BT_UART_D2R0.655––
BT_UART_R2D0.660––
BT_UART_RTS_L0.52––
BTROM_HOLD_L0.718––
BTROM_WP_L0.720––
CAMERA_PWR_EN0.52––
CAMERA_RESET_L0.47––
CHGR_ACIN0.62––
CHGR_AMON0.619––
CHGR_BGATE0.67––
CHGR_BMON0.62––
CHGR_BOOST_DH0.90––
CHGR_BOOST_DL0.46––
CHGR_BOOST_SW0.472––
CHGR_BOOT10.590––
CHGR_BOOT20.619––
CHGR_BOOT2_RC0.611––
CHGR_BUCK_DH0.915––
CHGR_BUCK_DL0.47––
CHGR_COMP0.62––
CHGR_CSI_N0.545–14.000R
CHGR_CSI_P0.547–14.000R
CHGR_CSI_R_N0.540––
CHGR_CSI_R_P0.540––
CHGR_CSO_N0.461–3.700R
CHGR_CSO_P0.461–3.700R
CHGR_CSO_R_N0.460––
CHGR_CSO_R_P0.460––
CHGR_LDO_P3V00.61––
CHGR_LDO_P5V00.43––
CHGR_LDO_VDDA0.436––
CHGR_LDO_VDDP0.443––
CHGR_PHASE0.452––
CHGR_PHASE10.435–127.000R
CHGR_PHASE20.430–127.000R
CPU_CATERR_L0.32––
CPU_CFG_RCOMP0.06––
CPU_CFG<3>0.33––
CPU_DIMM_VREFCA0.46––
CPU_DIMMA_VREFDQ0.52––
CPU_DIMMB_VREFDQ0.53––
CPU_PECI_R0.325––
CPU_PROCHOT_L0.23––
CPU_PWR_DEBUG_L0.33––
CPU_PWRGD0.36––
CPU_SM_RCOMP<0>0.19––
CPU_SM_RCOMP<1>0.12––
CPU_SM_RCOMP<2>0.10––
CPU_VCCST_PWRGD0.50––
CPU_VIDALERT_R_L0.31––
CPU_VIDSCLK0.23––
CPU_VIDSOUT0.23––
CPU_VR_EN0.32––
CPU_VR_READY0.57––
CPUBMONSNS_ALERT_L0.763––
CPUCORE_SW11.000–1.600R
CPUCORE_SW21.000–1.600R
CPUCORE_SW32.000–1.700R
CPUGT_SW13.000–5.000R
CPUGT_SW23.000–5.000R
CPUTHMSNS_ADDR_SEL0.004––
CPUTHMSNS_ALERT_L0.699––
CPUTHMSNS_D2_N0.75––
CPUTHMSNS_D2_P0.75––
CPUTHMSNS_DUR_SEL0.774––
CPUTHMSNS_TH_SEL0.773––
CPUVR_BOOT10.608––
CPUVR_BOOT20.610––
CPUVR_COMP0.615––
CPUVR_FB0.588––
CPUVR_FB20.628––
CPUVR_FCCM0.60––
CPUVR_ISEN10.633––
CPUVR_ISEN20.634––
CPUVR_ISNS1_N0.110––
CPUVR_ISNS1_P0.110––
CPUVR_ISNS2_N0.109––
CPUVR_ISNS2_P0.109––
CPUVR_ISUMN_R0.323––
CPUVR_ISUMP0.520––
CPUVR_LGATE10.432––
CPUVR_LGATE20.433––
CPUVR_NTC0.633––
CPUVR_PHASE10.110–85.100R
CPUVR_PHASE20.109–85.100R
CPUVR_PROG10.62––
CPUVR_PROG20.62––
CPUVR_PROG30.63––
CPUVR_PWM10.61––
CPUVR_PWM20.61––
CPUVR_SWSA0.011–16.700R
CPUVR_UGATE10.540––
CPUVR_UGATE20.541––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.492––
DDR_REG_ILIM0.482––
DDR_VREF_CMD0.43––
DDR_VREF_DATA0.41––
DDRREG_DRVH0.806––
DDRREG_DRVL0.477––
DDRREG_LL0.274––
DDRREG_VBST0.613––
DP_E85SNK_AUXCH_N0.738––
DP_E85SNK_AUXCH_P0.737––
DP_E85SNK_HPD0.52––
DP_E85SNK_ML_N<0>0.338––
DP_E85SNK_ML_N<1>0.759––
DP_E85SNK_ML_N<2>OL––
DP_E85SNK_ML_N<3>0.320––
DP_E85SNK_ML_P<0>0.338––
DP_E85SNK_ML_P<1>0.754––
DP_E85SNK_ML_P<2>OL––
DP_E85SNK_ML_P<3>0.320––
DP_INT_AUX_NOL––
DP_INT_AUX_POL––
DP_INT_HPD0.790––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
DP_TBTSNK0_AUXCH_C_N0.444––
DP_TBTSNK0_AUXCH_C_P0.445––
E85_CC10.556––
E85_CC20.56––
E85_HS_DP_ML0_N0.460––
E85_HS_DP_ML0_P0.696––
E85_HS_DP_ML1_N0.725––
E85_HS_DP_ML1_P0.725––
E85_LS_DXDEBUG_RX_DAT0.575––
E85_LS_DXDEBUG_TX_CLK0.570––
E85_LS_MISSION_N0.490––
E85_LS_MISSION_P0.488––
E85_LS_N<1>0.497––
E85_LS_N<2>0.488––
E85_LS_P<1>0.481––
E85_LS_P<2>0.484––
E85_LS_RFUDEBUG_RX_DAT0.583––
E85_LS_RFUDEBUG_TX_CLK0.585––
E85_RFU<1>0.645––
E85_RFU<2>0.644––
E85_TEST_MODE_HPD0.529––
E85_TEST_MODE_L0.532––
E85HSMUX_DP_EN0.619––
E85HSMUX_DP_EN_L0.625––
E85HSMUX_DPRDCI_EN0.828––
E85HSMUX_HS_EN0.521––
E85HSMUX_HS_FLIP0.487––
E85HSMUX_USB_EN0.486––
E85LSMUX_DEBUG_A_EN0.505––
E85LSMUX_DEBUG_B_EN0.506––
E85LSMUX_DEBUG_FLIP_L0.494––
E85LSMUX_DX_FLIP0.627––
E85LSMUX_HPM_SWD_EN0.522––
E85LSMUX_M_EN0.414––
E85LSMUX_M_SEL00.417––
E85LSMUX_M_SEL10.418––
E85LSMUX_RFU_EN_L0.540––
E85LSMUX_SMC_SWD_EN0.521––
EDP_BKLT_EN0.42––
EDP_BKLT_PWM0.66––
EDP_PANEL_PWR0.65––
GFXIMVP_PHASE11.000––
GFXIMVP_PHASE21.000––
GFXIMVP_PHASE31.000–1.800R
GPUFB_LL0.207––
HDA_BIT_CLK0.45––
HDA_RST_L0.45––
HDA_SDIN00.41––
HDA_SDOUT0.45––
HDA_SYNC0.45––
HPM_PIO0_70.541––
HPM_POWER_GATE_EN0.586––
HPM_RESET_L0.65––
HPM_SWCLK0.57––
HPM_SWCLK_R0.572––
HPM_SWDIO_R0.571––
HPM_SWITCH_EN_L0.576––
HPM_UART_RX0.54––
HPM_UART_TX0.53––
HPM_VBUS_VDET0.575––
HPM_VBUSFET_EN0.586––
I2C_BKLT_SCL0.52––
I2C_BKLT_SDA0.53––
I2C_CAM_SCK0.53––
I2C_CAM_SDA0.76––
I2C_HPM_SCL0.51––
I2C_HPM_SDA0.53––
I2C_PCH_1_SCL0.55––
I2C_PCH_1_SDA0.550––
INLET_THMSNS_D1_N0.75––
INLET_THMSNS_D1_P0.75––
ISNS_1V2_S3_N0.272––
ISNS_HS_COMPUTING_IOUT0.709––
ISNS_HS_COMPUTING_N0.460––
ISNS_HS_COMPUTING_P0.460––
ISNS_HS_GAIN_N0.66––
ISNS_HS_GAIN_OUT0.710––
ISNS_HS_GAIN_P0.346––
ISNS_LCDBKLT_N0.46––
ISNS_LCDBKLT_P0.46––
JTAG_WLAN_SEL0.74––
JTAG_WLAN_TDI0.76––
LCD_IRQ_L0.54––
LCD_PWR_SLEW0.716––
LCDBKLT_EN_LOL––
LPC_PWRDWN_L0.63––
MCP_EDP_RCOMP0.18––
MCP_RSVD_CK130.33––
MEM_A_ZQ_A0.25––
MEM_A_ZQ_B0.25––
MEM_B_CAA<0>0.27––
MEM_B_CAA<2>0.27––
MEM_B_CAA<3>0.27––
MEM_B_CAB<1>0.27––
MEM_B_CKE<1>0.27––
MEM_B_CLK_N<0>0.29––
MEM_B_CLK_P<0>0.29––
MEM_B_CS_L<0>0.27––
MEM_B_CS_L<1>0.27––
MEM_B_DQ<0>0.28––
MEM_B_DQS_N<0>0.28––
MEM_B_DQS_P<0>0.28––
MEM_B_ZQ_A0.25––
MEM_B_ZQ_B0.25––
MEM_CAM_A<8>0.43––
MEM_CAM_CS_L0.43––
MIPI_CLK_CONN_N0.410––
MIPI_CLK_CONN_P0.400––
MIPI_DATA_CONN_N0.40––
MIPI_DATA_CONN_P0.41––
NAND_OVERTMP_ALERT_L0.590––
P0V8SLPDDR_SW00.021––
P0V8SLPDDR_SW10.021––
P0V9_LX0_SSD00.251––
P0V9_LX1_SSD00.250––
P0V9SLPDDR_SW00.027––
P0V9SLPDDR_SW10.027––
P1V1_SSD_REG_FB1.408––
P1V1SLPS2R_SW00.334––
P1V1SLPS2R_SW10.333––
P1V1SSD_PGOOD0.543––
P1V1SSD_PHASE0.190––
P1V1SSD_SS0.756––
P1V1SSD_VOS0.203––
P1V2_CAM_SRVLXC_PHASE0.335––
P1V2_PHASE0.071––
P1V2_WLANBT_VLX0.266–1.918k
P1V05_SUS_EN0.48––
P1V05_SUS_IMON0.45––
P1V05_SUS_MODE0.48––
P1V05_SUS_PGOOD0.50––
P1V05_SUS_PHASE0.350––
P1V05_ULQ_L0.570––
P1V5_WLANBT_VLX0.300––
P1V05S0_EN0.570––
P1V5S0_EN0.55––
P1V05S4SW_FB0.777––
P1V05S4SW_PGOOD0.769––
P1V05S4SW_SW0.430––
P1V05SUS_DRVH0.88––
P1V05SUS_DRVL0.48––
P1V05SUS_LL0.350––
P1V8_LX0_SSD00.327––
P1V8S3_PHASE0.38––
P1V8SLPS2R_SW00.378––
P1V35_CAM_SRVLXD_PHASE0.270––
P2V5_SW1_TPS62180_SSD00.350––
P2V5_SW1_TPS62180_SSD10.3522.500–
P2V5_SW2_TPS62180_SSD00.351––
P2V5S3_REG0.420––
P3V3_G3H_REG_FB0.39––
P3V3_S0_EN0.47––
P3V3_S0_IMON0.45––
P3V3_S0_MODE0.48––
P3V3_S0_PGOOD0.50––
P3V3_S5_EN0.48––
P3V3_S5_IMON0.45––
P3V3_S5_MODE0.48––
P3V3G3H_BOOT0.586––
P3V3G3H_SW0.39––
P3V3G3H_VSW0.399––
P3V3G3HRTC_PHASE10.403––
P3V3S0_EN0.55––
P3V3S0_PHASE0.350––
P3V3S3_EN0.48––
P3V3S5_PHASE0.390––
P3V3SSD_PHASE0.360––
P5V_S4_EN0.48––
P5V_S4_IMON0.45––
P5V_S4_MODE0.48––
P5V_S4_PGOOD0.48––
P5V1R3V4_AGND0.003––
P5VG3S_VSW0.381––
P5VOUT_EN0.56––
P5VOUT_EN_L0.622––
P5VOUT_FB1.401––
P5VOUT_PGOOD0.542––
P5VOUT_PHASE0.480––
P5VOUT_SS0.752––
P5VOUT_VOS0.486––
P5VS0_BOOT0.627––
P5VS0_EN0.47––
P5VS0_PHASE0.430––
P5VS4_PHASE0.41––
P5VUSBC_X_LL0.479––
P5VUSBC_X_R0.479––
P5VUSBCT_LL0.473––
P5VUSBCT_R0.472––
PAK_SMC_RESET0.501––
PANEL_P5V_EN0.569––
PBUS_S0_VSENSEOL––
PBUSVSENS_EN_L0.490––
PBUSVSENS_EN_L_DIVOL––
PCH_BT_UART_CTS_L0.480––
PCH_BT_UART_D2R0.528––
PCH_BT_UART_R2D0.537––
PCH_BT_UART_RTS_L0.69––
PCH_CLK32K_PMIC0.480––
PCH_INTRUDER_L0.79––
PCH_INTVRMEN0.79––
PCH_JTAGX0.05––
PCH_OPI_COMP0.05––
PCH_PCIE_RCOMP0.78––
PCH_PCIEPHY_PC0.51––
PCH_PMTEST_RST0.400––
PCH_RTCRST_L0.790––
PCH_SATA_RCOMP0.78––
PCH_SATAPHY_PC0.500––
PCH_SRTCRST_L0.79––
PCH_STRP_TOPBLK_SWP_L0.550––
PCH_TBT_PCIE_RESET_L0.523––
PCH_UART_SSD_L_BT_H0.528––
PCH_UART1_D2R0.51––
PCH_UART1_R2D0.53––
PCH_USB3PHY_PC0.510––
PCIE_CLK100M_SSD_N0.28––
PCIE_CLK100M_SSD_P0.28––
PCIE_CLK100M_TBT_N0.262––
PCIE_CLK100M_TBT_P0.265––
PCIE_TBT_D2R_N<0>0.340––
PCIE_TBT_D2R_P<0>0.340––
PCIE_TBT_R2D_C_N<0>0.332––
PCIE_TBT_R2D_C_P<0>0.332––
PDCIN_E85_SS_DIVOL––
PDCINVSENS_EN_L_DIVOL––
PDDR_S3_PHASE0.275––
PLT_RESET_L0.52––
PM_BATLOW_L0.53––
PM_CLK32K_SUSCLK_R0.670––
PM_DSW_PWRGD0.50––
PM_PCH_APWROK0.52––
PM_PCH_PWROK0.52––
PM_PCH_SYS_PWROK0.50––
PM_PWRBTN_L0.62––
PM_RSMRST_L0.740––
PM_SLP_A_L0.52––
PM_SLP_S0_L0.46––
PM_SLP_S3_L0.47––
PM_SLP_S4_L0.49––
PM_SLP_S5_L0.57––
PM_SLP_SUS_L0.51––
PM_SYSRST_L0.62––
PM_THRMTRIP_L0.29––
PMIC_ADC_EN0.48––
PMIC_PWRBTN_L0.48––
PMIC_V8_EN0.46––
PMIC_VREF1V250.478––
PMIC_VREF2V40.484––
PMIC_VREF3V30.432––
PMIC_VREF3V3_RC0.425––
PMIC2_READY0.49––
PP0V9_SLPDDR0.027––
PP0V9_SSD00.252––
PP0V9_TBT_X_SVR0.244–646.000R
PP0V82_SLPDDR0.021––
PP0V95_S0_CPUVCCIO_REG_R0.038–53.000R
PP0V675_CAM_VREF0.56––
PP0V675_MEM_CAM_VREFCA0.50––
PP1V1_S0SW_SSD0.190––
PP1V1_SLPS2R0.334––
PP1V2_CAM0.335––
PP1V2_CAM_PCIE_PVDD_FLT0.346––
PP1V2_CAM_PCIE_VDD_FLT0.346––
PP1V2_CAM_XTALPCIEVDD0.346––
PP1V2_S0SW_SSD_COLD0.300––
PP1V2_S0SW_SSD_HOT0.340––
PP1V2_S30.275–128.000R
PP1V2_S3_CPUDDR0.069––
PP1V2_S3_REG_R0.071––
PP1V2_S5_SMC_VDDC0.51––
PP1V2_WLANBT_C0.266––
PP1V05_S00.190––
PP1V5_S00.360––
PP1V05_S0_PCH_VCC_ICC0.19––
PP1V05_S0_PCH_VCC_ICC_R0.190––
PP1V05_S0_PCH_VCCACLKPLL0.190––
PP1V05_S0_PCH_VCCACLKPLL_R0.190––
PP1V05_S0_PCH_VCCAPLL_OPI0.190––
PP1V05_S0SW_PCH_PCIE0.300––
PP1V05_S0SW_PCH_SATA0.325––
PP1V05_S0SW_PCH_USB30.320––
PP1V05_S0SW_PCH_VCCSATA3PLL0.325––
PP1V05_S0SW_PCH_VCCUSB3PLL0.32––
PP1V05_S4SW0.390––
PP1V05_SUS0.350––
PP1V05_SUS_PCH_VCCAOSCSUS0.34––
PP1V5R1V35_GPU_REG_R0.207––
PP1V8_CAM0.50––
PP1V8_S0_GPU0.233––
PP1V8_S0SW_SSD_COLD0.350––
PP1V8_S0SW_SSD_HOT0.500––
PP1V8_S30.380––
PP1V8_SLPS2R0.377––
PP1V8_SSD00.327––
PP1V35_CAM0.27––
PP1V35_DDR_CLK0.27––
PP2V5_NAND_SSD00.3522.500–
PP2V5_S0SW_SSD0.44––
PP2V5_S30.420––
PP3V0_S5_AVREF_SMC0.58––
PP3V3_G3H0.39––
PP3V3_G3H_KBD_F0.39––
PP3V3_G3H_RTC_REG_R0.403––
PP3V3_G3H_T0.400––
PP3V3_S00.350––
PP3V3_S0_CPUTHMSNS_R0.39––
PP3V3_S0SW_LCD0.650––
PP3V3_S0SW_S1X0.59––
PP3V3_S0SW_SSD0.36––
PP3V3_S40.39––
PP3V3_S4_TPAD_F0.40––
PP3V3_S50.390––
PP3V3_S5_SMC_VDDA0.38––
PP3V3_SUS0.315––
PP3V3R3V0_AON0.32––
PP5V_G3H_LDO0.47––
PP5V_G3S0.382––
PP5V_S00.430––
PP5V_S0_ALSCAM_F0.430––
PP5V_S0_CPUVR_VDD0.44––
PP5V_S0_KBD_F0.42––
PP5V_S0SW_LCD0.570––
PP5V_S40.41––
PP5V_S4_TPAD_F0.45––
PP5V1_S4SW0.480––
PP5V1_S4SW_CC10.517––
PP5V1_S4SW_CC20.518––
PPBUS_G3H0.398––
PPBUS_G3H_SSD0_SNS0.398––
PPBUS_G3H_TPAD_FLT0.46––
PPBUS_G3H_TPAD_FUSED0.46––
PPBUS_HS_OTH5V0.399––
PPBUS_S0_LCDBKLT_FUSED0.46––
PPBUS_S0_LCDBKLT_PWR_SW0.44––
PPBUS_S5_HS_COMPUTING_ISNS0.460––
PPBUS_SW_BKL0.44––
PPBUS_SW_LCDBKLT_PWR0.46––
PPDCIN_E85_SS0.55––
PPDCIN_G3H0.54––
PPDCIN_G3H_CHGR0.534––
PPLCDBKLT_VDDA0.43––
PPLCDBKLT_VDDD0.42––
PPVBAT_G3H_CHGR_R0.400––
PPVBAT_G3H_CHGR_REG0.399––
PPVBAT_G3H_CONN0.64––
PPVBUS_E850.523––
PPVCC_CPU_PH11.000–1.600R
PPVCC_CPU_PH21.000–1.600R
PPVCC_CPU_PH31.000–2.100R
PPVCC_S0_CPU0.109––
PPVCC_S0_CPU_PH10.060–85.100R
PPVCC_S0_CPU_PH20.109–85.100R
PPVCCGT_CPU_PH13.000–5.000R
PPVCCGT_CPU_PH23.000–5.000R
PPVCCIO_S0_CPU0.039–52.600R
PPVCCPRIMCORE_PRIM_REG0.042––
PPVCCSA_CPU_R0.011–16.800R
PPVCOMP_S0_CPU0.15––
PPVCORE_S0_GFX_PH11.000––
PPVCORE_S0_GFX_PH21.000––
PPVCORE_S0_GFX_PH31.000–1.800R
PPVDDCI_S0_GPU0.017––
PPVDDCPU_AWAKE0.006––
PPVDDCPUSRAM_AWAKE0.145––
PPVIN_G3H_P3V3G3H0.52––
PPVIN_G3H_TPAD_FUSE0.398––
PPVIN_S0_CPUVR_VIN0.46––
PPVIN_S0SW_LCDBKLT0.852––
PPVIN_SW_LCDBKLT_SW0.852––
PPVOUT_S0_LCDBKLT1.158––
PPVOUT_S0_PCH_DCPRTC0.70––
PPVREF_S3_MEM_VREFCA0.45––
PPVREF_S3_MEM_VREFDQ_A0.52––
PPVREF_S3_MEM_VREFDQ_B0.27––
PPVRTC_G3H0.48––
PVCCIO_PHASE0.039–53.000R
PVCCPRIMCORE_SW00.042––
PVCCPRIMCORE_SW10.042––
PVDDCPUAWAKE_SW00.006––
PVDDCPUAWAKE_SW10.006––
PVDDCPUAWAKE_SW20.007––
PVDDCPUAWAKE_SW30.006––
PVDDCPUSRAMAWAKE_SW00.145––
PVIN_RFLDO_WLANBT_VLX0.304––
PVIN_S0_P1V1SSD_RC0.472––
PVIN_S4_P5VOUT_AIN0.470––
QR_SWITCH_EN0.52––
R_AMP1_GAIN0.600––
R_AMP2_GAIN0.600––
REG_PHASE_2V5S30.420––
RF_0_ANTOL––
S1X_DEBUG_UART_D2R0.42––
S1X_DEBUG_UART_R2D0.42––
S5_PWRGD0.48––
SAK_PP1V8_REF_P1V0.669––
SAK_SSD_COLD_BOOT_L0.54––
SAK_SSD_P1V1_DISCHARGE_FB0.001––
SAK_SSD_P1V2_EN0.553––
SAK_SSD_P1V8_EN0.553––
SAK_SSD_P3V3_DISCHARGE_FB0.001––
SAK_SSD_PCIE_RESET_L0.56––
SAK_SSD_PP1V1_EN0.56––
SAK_SSD_SR_P1V2_EN0.550––
SAK_SSD_SR_P1V8_EN0.552––
SMBUS_PCH_CLK0.57––
SMBUS_PCH_DATA0.57––
SMBUS_SMC_0_S0_SCL0.740––
SMBUS_SMC_0_S0_SDA0.740––
SMBUS_SMC_1_S0_SCL0.53––
SMBUS_SMC_1_S0_SDA0.53––
SMBUS_SMC_2_G3_SCL0.41––
SMBUS_SMC_2_G3_SDA0.41––
SMBUS_SMC_3_SCL0.740––
SMBUS_SMC_3_SDA0.74––
SMBUS_SMC_5_G3_SCL0.60––
SMBUS_SMC_5_G3_SDA0.58––
SMC_ACTUATOR_DISABLE_L0.74––
SMC_ADAPTER_EN0.61––
SMC_BC_ACOK0.61––
SMC_BMON_ISENSE0.74––
SMC_CBC_ON0.61––
SMC_CHGR_INT_L0.60––
SMC_CLK12M_EN0.46––
SMC_CLK32K_PMIC0.690––
SMC_CPU_ISENSE0.620––
SMC_DCIN_ISENSE0.74––
SMC_DCIN_VSENSE0.74––
SMC_DEBUGPRT_RX_L0.515––
SMC_DEBUGPRT_TX_L0.513––
SMC_HS_COMPUTING_ISENSE0.74––
SMC_LID0.75––
SMC_LRESET_L0.52––
SMC_LSOC_RST0.62––
SMC_ONOFF_L0.720––
SMC_OOB1_R2D_L0.576––
SMC_PBUS_VSENSE0.74––
SMC_PCH_SUSACK_L0.60––
SMC_PCH_SUSWARN_L0.620––
SMC_PECI_L_R0.749––
SMC_PME_S4_WAKE_L0.49––
SMC_PROCHOT0.74––
SMC_RESET_L0.74––
SMC_RST_L0.610––
SMC_SENSOR_PWR_EN0.75––
SMC_SWCLK_R0.626––
SMC_SWDIO_R0.624––
SMC_TCK0.62––
SMC_TDI0.74––
SMC_TDO0.46––
SMC_THRMTRIP0.74––
SMC_TMS0.62––
SMC_VCCIO_CPU_DIV20.74––
SMC_WAKE_SCI_L0.51––
SMC_WIFI_PWR_EN0.45––
SPI_ALT_CLK0.52––
SPI_ALT_CS_L0.54––
SPI_ALT_IO<2>0.52––
SPI_ALT_IO<3>0.53––
SPI_ALT_MISO0.52––
SPI_ALT_MOSI0.53––
SPI_DESCRIPTOR_OVERRIDE1.347––
SPI_DESCRIPTOR_OVERRIDE_L0.751––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.609––
SPI_IO<2>0.51––
SPI_IO<3>0.52––
SPI_MLB_CLK0.524––
SPI_MLB_CS_L0.550––
SPI_MLB_IO<2>0.511––
SPI_MLB_IO<3>0.528––
SPI_MLB_MISO0.502––
SPI_MLB_MOSI0.529––
SPI_MLBROM_CS_L0.65––
SPIROM_USE_MLB0.52––
SPKRAMP_LOUT1_N0.48––
SPKRAMP_LOUT1_P0.49––
SPKRAMP_LOUT2_N0.49––
SPKRAMP_LOUT2_P0.49––
SPKRAMP_LT_OUTN0.480––
SPKRAMP_LT_OUTP0.481––
SPKRAMP_LW_OUTN0.481––
SPKRAMP_LW_OUTP0.479––
SPKRAMP_ROUT1_N0.480––
SPKRAMP_ROUT1_P0.480––
SPKRAMP_ROUT2_N0.490––
SPKRAMP_ROUT2_P0.490––
SPKRCONN_LT_OUTN0.480––
SPKRCONN_LT_OUTP0.481––
SPKRCONN_LW_OUTN0.480––
SPKRCONN_LW_OUTP0.479––
SPKRVNDR_L_IDOL––
SPKRVNDR_R_IDOL––
SSD_BOOT0.62––
SSD_CLKREQ_L0.49––
SSD_CORE_SHMOO<0>0.45––
SSD_CORE_SHMOO<1>0.500––
SSD_GPIO1_L0.618––
SSD_GPIO2_L0.615––
SSD_I2C_SCL0.475––
SSD_I2C_SDA0.466––
SSD_JTAG_MASTER_NRST0.45––
SSD_JTAG_MASTER_TCK0.45––
SSD_JTAG_MASTER_TDI0.45––
SSD_JTAG_MASTER_TDO0.49––
SSD_JTAG_MASTER_TMS0.45––
SSD_P1V2_COLD_SW_CAP0.707––
SSD_P1V8_COLD_SW_CAP0.708––
SSD_PWR_EN0.50––
SSD_RESET_L0.52––
SSD_SPI_CS_L0.47––
SSD_SPI_MISO0.43––
SSD_SPI_MOSI0.43––
SSD_SPI_SCLK0.43––
SSD_SPI_SIO30.668––
SSD_SPI_WP_L0.601––
SSD_SR_EN_L0.54––
SSD_UART_BOOT_L0.440––
SSD_UART_D2R0.471––
SSD_UART_R2D0.468––
SYS_DETECTOL––
SYS_DETECT_L0.49––
SYSCLK_CLK12M_SMC0.47––
SYSCLK_CLK24M_CAMERA0.46––
SYSCLK_CLK24M_SB0.45––
SYSCLK_CLK24M_SB_R0.57––
SYSCLK_CLK24M_X10.455––
SYSCLK_CLK24M_X20.455––
SYSCLK_CLK24M_X2_R0.455––
SYSCLK_CLK32K_PMIC0.44––
TBT_CLKREQ_L0.35––
TP_IST_TRIGGER0.33––
TP_IVR_ERROR0.33––
TP_JTAG_WLAN_TCK0.75––
TP_JTAG_WLAN_TDO0.58––
TP_JTAG_WLAN_TRST0.76––
TP_MCP_DC_A44OL––
TP_MCP_DC_C45OL––
TP_MCP_DC_CW10.27––
TP_MCP_DC_CY30.27––
TP_MCP_DC_CY440.11––
TP_MCP_DC_D2OL––
TP_MCP_DC_F1OL––
TP_MCP_DC_H440.500––
TP_MCP_RSVD_BJ140.44––
TP_MCP_RSVD_BT150.39––
TP_MCP_RSVD_Y180.370––
TP_PCH_SLP_LAN_L0.68––
TP_PCH_SLP_WLAN_L0.68––
TP_SSD_JTAG_SLAVE_TCK0.450––
TP_SSD_JTAG_SLAVE_TMS0.450––
TPAD_SPI_CLK_R0.53––
TPAD_SPI_CS_L0.550––
TPAD_SPI_IF_EN0.53––
TPAD_SPI_INT_L0.48––
TPAD_SPI_MISO_R0.54––
TPAD_SPI_MOSI_R0.52––
TS_HIPWR_EN0.56––
TS_HOST_RST0.625––
TS_POWER_GATE_EN0.60––
UNCONNECTED_50.490––
UNCONNECTED_60.490––
UNUSED_ANI_VREF0.680––
USB_EXTA_F_N0.435––
USB_EXTA_F_P0.436––
USB_EXTA_N0.433––
USB_EXTA_P0.433––
USB_HPM_R_N0.522––
USB_HPM_R_P0.522––
USB3_EXTA_D2R_N0.355––
USB3_EXTA_D2R_P0.355––
USB3_EXTA_R2D_NOL––
USB3_EXTA_R2D_POL––
USB3_EXTD_R2D_N0.755––
USB3_EXTD_R2D_P0.758––
VBUSFET_EN0.628––
VBUSFET_ILIM0.537––
VCFET_ILIM10.732––
VCFET_ILIM20.732––
VR_PHASE_GPU_VDDCI0.017––
VR0V9_IND_TBT_X0.245–651.000k
VRVDDCI_R0.017––
WLAN_ROM_CLK0.677––
WLAN_ROM_CS0.664––
WLAN_ROM_MISO0.620––
WLAN_ROM_MOSI0.677––
WLAN_ROM_ORG0.690––
XDP_CPU_PRDY_L0.30––
XDP_CPU_PREQ_L0.30––
XDP_CPU_PRESENT_L0.14––
XDP_CPU_PWRBTN_L0.62––
XDP_CPU_TCK0.06––
XDP_CPU_TDI0.33––
XDP_CPU_TDO0.23––
XDP_CPU_TMS0.33––
XDP_CPU_VCCST_PWRGD1.50––
XDP_CPUPCH_TRST_L0.30––
XDP_CPURST_L1.51––
XDP_DBRESET_L0.63––
XDP_FW_PME_L0.51––
XDP_JTAG_CPU_ISOL_L0.71––
XDP_JTAG_ISP_TCK0.50––
XDP_LPCPLUS_GPIO0.51––
XDP_MLB_RAMCFG00.500––
XDP_MLB_RAMCFG10.500––
XDP_MLB_RAMCFG20.500––
XDP_MLB_RAMCFG30.50––
XDP_PCH_GPIO170.49––
XDP_PCH_SATAPHY_PC0.500––
XDP_PCH_TCK0.33––
XDP_PCH_TDI0.57––
XDP_PCH_TDO0.37––
XDP_PCH_TMS0.37––
XDP_SDCONN_STATE_CHANGE_L0.51––
XDP_SYS_PWROK0.50––
XDP_TRST_L0.86––
XDP_USB_EXTA_OC_L0.52––
XDP_USB_EXTB_OC_L0.52––
XDP_USB_EXTC_OC_L0.52––
XDP_USB_EXTD_OC_L0.52––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00045?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00045: diode 0.398. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00045?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00045: diode 0.39. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-00045?

OpenBoardData's known-good values for PP3V3_S5 on the 820-00045: diode 0.390. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00045 board?

Open your own 820-00045 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License