Apple laptop board · OpenBoardData

820-01958 known-good readings

Known-good readings for the Apple laptop board 820-01958: 1,065 nets, including 72 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 69 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01958.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 72 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 33

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1SR3V3_G3H_P0V6_S3_VIN0.377––
AI: what PP1SR3V3_G3H_P0V6_S3_VIN is and how to check it
  • What it is: From the name, PP1SR3V3_G3H_P0V6_S3_VIN is a G3H always-on startup rail (3.3 V and 0.6 V sections implied by the name), present whenever the board has input power.
  • Known-good reading: Diode mode to ground, board unpowered: 0.377. This is a community guide value, not a spec.
  • How to check: Power off and unplug, then measure diode to ground on the rail. Then apply power and measure the voltage on it.
  • No known-good voltage reading here for this rail, so compare against a matching net or a known-good board.
  • A diode reading far below 0.377 usually suggests a short or leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PP1V8_G3S0.306––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V rail; the G3S suffix marks it as an always-on startup rail, from the name. The archive lists one known-good diode reading of 0.306 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.306 suggests a short or leaky part on the rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP1V8_G3S_THMSNS_R0.320––
AI: what PP1V8_G3S_THMSNS_R is and how to check it
  • What it is: From its name, PP1V8_G3S_THMSNS_R is a 1.8 V rail in the G3H always-on group, with "THMSNS" suggesting a thermal-sense related supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.320 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode to ground on the rail; then power on and measure the voltage, expecting about 1.8 V from the name.
  • If far off: a low diode reading usually points to a shorted load or part on the rail; a high or open reading points to a missing feed or broken trace. Confirm with a second measurement before replacing anything.
PP3V_G3H0.515––
AI: what PP3V_G3H is and how to check it
  • What it is: PP3V_G3H is a 3V always-on rail; the "G3H" suffix, from its name, marks it as an always-on startup rail.
  • Known-good reading: diode 0.515 (community archive, condition not stated). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V_G3H to ground; then apply power and measure the rail's voltage.
  • If far off: a much lower diode reading suggests a short or a leaky load on the rail; a much higher one suggests an open path. Treat this as a guide, not a confirmed fault.
PP3V3_G3H0.367 DFU%2bMode0.3633.300 DFU+Mode3.300–
PP3V3_G3H_IPD_F0.359––
AI: what PP3V3_G3H_IPD_F is and how to check it
  • PP3V3_G3H_IPD_F is a 3.3 V always-on rail; the G3H part of the name indicates it comes up in the always-on startup stage, and IPD_F is a name suffix whose meaning isn't documented here.
  • Known-good from the archive: diode mode to ground 0.359 (no condition recorded). No known-good voltage reading here.
  • Check it with the board unpowered: meter in diode mode, black probe on ground, red on the rail. Then power the board and measure the voltage on the rail.
  • A diode reading far below 0.359 suggests a short or a leaky part on the rail; far above suggests an open path. One reading alone doesn't prove a part bad, so compare with a matching net or a known-good board before replacing anything.
PP3V3_G3H_PMU_VDDMAIN0.367 DFU%2bMode0.3633.300 DFU+Mode3.300–
PP3V3_G3H_PMU_VINRTC_R0.420––
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check it
  • What it is: PP3V3_G3H_PMU_VINRTC_R is a 3.3 V always-on rail feeding the PMU's RTC input, judged from its name (G3H = always on, VINRTC = RTC supply). It should be present whenever the board has power.
  • Known-good reading: diode mode to ground is 0.420, from the readings archive. No known-good voltage reading is recorded here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.420. Then apply power and measure the voltage on the rail; expect about 3.3 V, though that figure is general, not from this board's data.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to the PMU or its supply. Treat these as likely causes, not confirmed ones.
PP3V3_G3H_RTC0.4103.300–
AI: what PP3V3_G3H_RTC is and how to check it
  • What it is: PP3V3_G3H_RTC is a 3.3 V always-on rail, from its name (G3H = always on), feeding the RTC side of the logic board.
  • Known-good readings (community archive, guide only): diode 0.410 to ground, voltage 3.300 with power applied.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a low diode reading or missing 3.3 V usually points to a short or a failed source on that rail, but that's a likely cause, not a confirmed one. No known-good resistance reading exists for this rail.
PP3V3_G3H_RTC_R0.4623.300–
AI: what PP3V3_G3H_RTC_R is and how to check it

PP3V3_G3H_RTC_R is an always-on 3.3 V rail, judging from the G3H and RTC in its name (general naming convention, not from board data). Known-good readings in the archive: diode 0.462 to ground and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.462 suggests a short or leaky load on the rail; a voltage well below 3.300 V points to the rail not coming up or being loaded down. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.

PP3V3_G3S0.379––
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is a 3.3 V rail. The "G3S" suffix marks it as a startup-stage rail that should be present whenever the board has power (that's from the name, not a schematic).

  • Known-good: diode to ground 0.379 (community reading, a guide only). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.379 suggests a short or a leaky load on the rail; far above suggests an open path. Confirm with voltage before suspecting a part.
PP3V3_G3S_G3H_RIO0.361––
AI: what PP3V3_G3S_G3H_RIO is and how to check it

PP3V3_G3S_G3H_RIO is a 3.3 V rail; the G3H part of its name marks it as an always-on startup rail, and G3S/RIO suggest it also feeds the RIO side of the 3.3 V standby domain (from the name, not from a schematic).

  • Known-good: diode-to-ground reading of 0.361 in the readings archive. That's a community guide, not a guaranteed value, and it depends on board state.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • No known-good voltage reading is recorded here, so compare against a matching 3.3 V rail or a known-good board.
  • A diode reading far below 0.361 usually points to a short or a leaky part on the rail; a much higher one can mean an open trace or missing part. Confirm with a second measurement before replacing anything.
PP3V3_G3S_IPD_F0.379––
AI: what PP3V3_G3S_IPD_F is and how to check it
  • What it is: PP3V3_G3S_IPD_F is a 3.3 V rail in the G3S (always-on) startup group, judged from its name; the "IPD_F" suffix likely marks a filtered or switched branch, but that's general inference, not board data.
  • Known-good reading: diode 0.379 (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage, expecting about 3.3 V.
  • If it's far off: a low or shorted diode reading usually points to a shorted load or decoupling cap on the rail; an open reading points to a missing feed. Confirm with a second measurement before replacing anything.
PP3V3_G3S_WLANBT0.378––
AI: what PP3V3_G3S_WLANBT is and how to check it

PP3V3_G3S_WLANBT is a 3.3 V supply rail for the WLAN/Bluetooth section, and the G3S in its name indicates it is an always-on (G3H) rail. The only known-good reading here is a diode value of 0.378 to ground, with no condition recorded; no known-good voltage reading is available. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.378 usually points to a short or a leaky component on the rail; a much higher or open reading points to a broken connection. Confirm with the voltage measurement before replacing anything.

PP3V3_G3SSW_SNS0.540––
AI: what PP3V3_G3SSW_SNS is and how to check it

PP3V3_G3SSW_SNS is a 3.3 V always-on rail (the G3H stage is from its name), likely a sense line for that supply. The archive lists a diode reading of 0.540 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from the net to ground and compare with 0.540. Then power up and check the voltage is near 3.3 V. A diode reading far from 0.540 points to a short or open on that net, but one reading alone doesn't confirm a bad part.

PP5V_G3S0.4065.000–
AI: what PP5V_G3S is and how to check it
  • What it is: PP5V_G3S is a 5 V rail. The "G3S" suffix indicates its startup stage from the name (G3S/G3H-style always-on/standby naming on Apple logic boards); the exact stage meaning is general convention, not from this board's data.
  • Known-good readings (guide, from the community archive): diode 0.406 to ground, and 5.000 V with power applied. No condition is recorded with these.
  • How to check: with the board unpowered, measure diode mode from PP5V_G3S to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points upstream at the rail's source or its enable. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board before condemning a part.
PP5V_G3S_IPD_F0.406––
AI: what PP5V_G3S_IPD_F is and how to check it

PP5V_G3S_IPD_F is a 5 V rail; the G3S part of the name indicates it is an always-on (G3H) startup rail, and the IPD_F suffix is not explained by the available data. The only known-good reading is a diode value of 0.406 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and compare against a matching rail or a known-good board. A diode reading far from 0.406 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP5V_G3S_P1V1REG0.008––
AI: what PP5V_G3S_P1V1REG is and how to check it
  • What it is: From the name, PP5V_G3S_P1V1REG is a 5 V rail in the G3S (always-on) startup stage, with a P1V1 regulator associated with it. Which parts sit on it isn't known from the readings archive alone.
  • Known-good reading: Diode 0.008 to ground, from the community archive. Treat it as a guide only; no voltage or resistance known-good value is recorded here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the rail voltage.
  • If it's far off: A diode reading well above 0.008 usually points to an open trace or missing part rather than a short. A near-zero reading can be normal for a low-voltage rail, so compare with a known-good board before condemning anything.
PPBUS_G3H0.41013.050–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this 820-01958; the "G3H" suffix, from the name, marks it as an always-on rail. In the readings archive its known-good values are a diode reading of 0.410 to ground and 13.050 V with power applied — treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode from PPBUS_G3H to ground first, then power the board and measure the voltage. A diode reading far from 0.410 suggests a short or a leaky part on the bus; a voltage far from 13.050 V points to a charging or power-supply problem upstream. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board if you need one.

PPBUS_G3H_SPKRL0.41013.050–
AI: what PPBUS_G3H_SPKRL is and how to check it

PPBUS_G3H_SPKRL — 820-01958 reference note

  • What it is: from the name, the G3H part means an always-on main bus rail (PPBUS), and the SPKRL suffix points to a speaker-related branch of it. The exact parts on this net aren't documented here.
  • Known-good readings (community archive, guide only): diode 0.410 to ground, voltage 13.050.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading or a collapsed voltage usually points to a short or a heavy load on that branch. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board before condemning anything.
PPBUS_G3H_SSD00.41013.050–
AI: what PPBUS_G3H_SSD0 is and how to check it
  • What it is: PPBUS_G3H_SSD0 is the main bus rail feeding the SSD section; the G3H part of the name indicates it is always-on, and that reading is from the name, not from board data.
  • Known-good readings: diode 0.410 and voltage 13.050, from the readings archive (community-contributed, so treat as a guide; no condition is recorded).
  • How to check it: with the board unpowered, measure diode mode from PPBUS_G3H_SSD0 to ground; then apply power and measure the voltage on the rail.
  • If far off: a diode reading well below 0.410 suggests a short or leaky part on the rail; a voltage well under 13.050 suggests the rail isn't coming up or is loaded down. There is no known-good resistance reading for this rail.
PPBUS_G3H_TPAD_FLT0.42212.500–
AI: what PPBUS_G3H_TPAD_FLT is and how to check it
  • What it is: From the name, PPBUS_G3H_TPAD_FLT is the main PPBUS rail feeding the trackpad, with G3H meaning it should be present whenever the board has power (always-on stage). The FLT suffix suggests a filtered or fault-related branch.
  • Known-good readings: Diode 0.422 and voltage 12.500 V, from the readings archive only (community-contributed, so treat as a guide; no condition is recorded).
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.422. Then apply power and measure the voltage, expecting around 12.5 V.
  • If it's far off: A diode reading well below known-good often points to a shorted component on the rail; a missing or low voltage with a normal diode reading points upstream, toward the PPBUS source or its enable. No known-good resistance reading is available here, so compare against a matching net or a known-good board.
PPDCIN_G3H0.54220.000–
AI: what PPDCIN_G3H is and how to check it
  • What it is: PPDCIN_G3H is the DC input rail; the G3H suffix (from the name) marks it as always-on, present whenever a charger is connected.
  • Known-good readings: diode 0.542 to ground, voltage 20.000 V with the charger connected (community readings, a guide only).
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply the charger and measure the voltage on the rail.
  • If it's far off: a low or shorted diode reading points to a short on the input side; no or low voltage with a good charger points to the input path or charger detection. No known-good resistance reading is available for this rail.
PPDCIN_G3H_CHGR_AMON0.54220.000–
AI: what PPDCIN_G3H_CHGR_AMON is and how to check it

PPDCIN_G3H_CHGR_AMON is the charger-side DC input rail with a current-monitor sense line, judged from its name; the G3H part means it's always-on. The archive lists a known-good diode reading of 0.542 and a voltage of 20.000, with no condition recorded. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage. A diode reading far below 0.542 usually points to a short or leaky part on the rail; a voltage well off 20.000 points upstream to the charger input or its supply. No known-good resistance reading exists for this rail.

PPHV_INT_T_G3H0.54220.000–
AI: what PPHV_INT_T_G3H is and how to check it

PPHV_INT_T_G3H (820-01958) — a rail in the always-on G3H domain, judging from the name.

  • Known-good readings from the archive: diode 0.542 to ground, and 20.000 V with power applied. These are community readings and only a guide; the data gives no condition for them.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far from 0.542 usually points to a short or a damaged part on that rail; a voltage far from 20.000 V points to a supply or enable problem upstream.
  • No known-good resistance reading is listed here.
PPHV_INT_X_G3H0.54220.000–
AI: what PPHV_INT_X_G3H is and how to check it

PPHV_INT_X_G3H — reference note

  • From its name, this is a high-voltage (PPHV) internal rail in the G3H always-on domain, so it should be present whenever the board has power, not only after the main rails come up.
  • Known-good readings from the archive: diode 0.542 to ground, and 20.000 V with power applied. These are community readings and only a guide; no known-good resistance value is recorded here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage at the same point.
  • A diode reading well below 0.542 usually suggests a short or a leaky part on the rail; a voltage far from 20.000 V points to a supply or enable problem upstream. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R0.41013.050–
AI: what PPVBAT_G3H_CHGR_R is and how to check it
  • What it is: PPVBAT_G3H_CHGR_R is a battery/charger-related power rail; the G3H part of the name indicates it is always-on (from the name, not from a schematic).
  • Known-good readings: diode 0.410 and voltage 13.050, from community readings and only a guide; no resistance value is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail, and a missing or low voltage points to the supply feeding it or an overload; confirm with a second measurement before replacing anything.
PPVBAT_G3H_CONN1.38913.050–
AI: what PPVBAT_G3H_CONN is and how to check it
  • What it is: From the name, PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H supply (G3H usually means "always on" in general Apple naming). It's the raw battery/DC-in feed into the board.
  • Known-good readings (community archive, guide only): diode 1.389 and voltage 13.050. No known-good resistance reading here.
  • How to check: With the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or heavy load on the rail, but one reading alone doesn't confirm a bad part — compare against a matching net or a known-good board before replacing anything.
PPVBAT_G3H_FUSE1.38913.050–
AI: what PPVBAT_G3H_FUSE is and how to check it
  • What it is: From the name, PPVBAT_G3H_FUSE is the battery-supply rail after its fuse, in the always-on G3H group — so it should be present whenever a battery or charger feeds the board.
  • Known-good readings (guide, from community archive): diode 1.389 to ground, voltage 13.050. No known-good resistance value here.
  • How to check: Power off and unplugged, diode mode from the rail to ground; then power applied, measure the voltage on the rail.
  • If far off: A diode reading well below known-good usually points to a short or leaky part on that rail or downstream of the fuse; a missing or low voltage points to the fuse, the supply feeding it, or a heavy load pulling it down. Confirm with a second measurement before replacing anything.
PPVIN_G3H_P1V1_S30.410––
AI: what PPVIN_G3H_P1V1_S3 is and how to check it

PPVIN_G3H_P1V1_S3 is a supply rail: from its name, "G3H" means always-on, and "P1V1" suggests a 1.1 V rail (general naming, not confirmed by board data). The only known-good reading here is a diode value of 0.410 to ground; there is no known-good voltage reading in this data.

  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Compare against 0.410.
  • Then power the board and measure the DC voltage on the rail.
  • A diode reading far below 0.410 usually points to a short or a failing load on the rail; far above can mean an open path. A small difference may be normal, so don't condemn a part on one reading.
PPVIN_G3H_P3V3G3H0.41013.050–
AI: what PPVIN_G3H_P3V3G3H is and how to check it
  • What it is: From its name, PPVIN_G3H_P3V3G3H is the G3H (always-on) input rail feeding the 3V3G3H supply on the 820-01958. It is a startup-stage rail, present whenever input power is connected.
  • Known-good readings (guide, from community data): diode 0.410 to ground, and 13.050 V with power applied.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage.
  • If far off: A diode reading well below 0.410 suggests a short or leaky load on the rail; a much higher one suggests an open path. Low or missing voltage with power applied points to the input supply or an upstream protection component. No known-good resistance reading is recorded for this rail, so compare against a matching net or a known-good board.
PPVIN_G3H_P3V3G3HRTC0.48012.500–
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC is an always-on (G3H) input rail, judging from its name; the P3V3G3HRTC part suggests it feeds the 3.3 V RTC section. Known-good readings from the archive are diode 0.480 and voltage 12.500 V, with no condition recorded. Check it unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far from 0.480 points to a short or leaky part on the rail; a missing or wrong voltage points upstream, toward the supply feeding it. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PPVIN_G3H_P5VG3S0.41013.050–
AI: what PPVIN_G3H_P5VG3S is and how to check it

PPVIN_G3H_P5VG3S is an always-on (G3H, from the name) input rail, likely the 5V G3S input feed — that's general interpretation, not from board data. Known-good readings here: diode 0.410 to ground and 13.050 V with power applied. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode far below 0.410 suggests a short or leaky load on the rail; a voltage well off 13.050 points to a supply or upstream fault. No known-good resistance reading is available for this rail.

S5 and SUS: standby 2

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.347––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply, present before the board fully powers on. The only known-good reading here is a diode value of 0.347 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.347 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S5_LDO0.469––
AI: what PP5V_S5_LDO is and how to check it
  • What it is: PP5V_S5_LDO is a 5 V standby rail; the "S5" and "SUS" in the name indicate it belongs to the standby stage, and "LDO" suggests it comes from a low-dropout linear regulator (from the name, not from board data).
  • Known-good reading: diode 0.469 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S5_LDO to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail, and no voltage at all points to the standby supply or its enable not coming up. These are general guidelines, not confirmed causes.

S4 6

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP0V9_SSD0_S4E0_VDD_PLL0.430––
AI: what PP0V9_SSD0_S4E0_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail feeding the SSD's PLL supply, active in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good: Diode reading to ground 0.430. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open connection. The voltage should sit near 0.9 V once the board reaches S4.
PP0V9_SSD0_S4E1_VDD_PLL0.425––
AI: what PP0V9_SSD0_S4E1_VDD_PLL is and how to check it
  • What it is: From its name, PP0V9_SSD0_S4E1_VDD_PLL is a 0.9 V rail feeding the SSD's PLL, active in the S4 state. The name is the only source here; the parts on the net aren't known.
  • Known-good: Diode reading to ground is 0.425 (community reading, a guide only). No known-good voltage or resistance value is listed here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power on into S4 and measure the voltage at the rail.
  • If it's far off: A diode reading well below 0.425 suggests a short or leaky part on the rail; a much higher or open reading suggests a broken trace or missing feed. Confirm with the voltage reading before replacing anything.
PP1V8_SSD0_S4E0_AVDD18_PLL0.3901.800–
AI: what PP1V8_SSD0_S4E0_AVDD18_PLL is and how to check it
  • What it is: From its name, PP1V8_SSD0_S4E0_AVDD18_PLL is a 1.8 V rail feeding the SSD's PLL supply (AVDD18), enabled in the S4 power state. The "S4" stage comes from the name, not from a schematic.
  • Known-good readings (community archive, guide only): diode 0.390 to ground, and 1.800 V with the rail up.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.390 suggests a short or a leaky part on the rail; no voltage where 1.800 V is expected points to the rail not being enabled or its source failing. There's no known-good resistance reading for this rail here, so compare against a matching net or a known-good board.
PP1V8_SSD0_S4E0_PCI_AVDD_H0.3901.800–
AI: what PP1V8_SSD0_S4E0_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail (PP1V8) for SSD/PCIe AVDD, in the S4 startup stage. The board data doesn't list which parts sit on it.
  • Known-good readings: diode 0.390 to ground and 1.800 V with power applied. These are community readings and a guide only; no known-good resistance value here.
  • How to check: Power off and unplug, then diode mode from the rail to ground. Then power up and measure the voltage.
  • If far off: a much lower diode reading suggests a short or a failing load on the rail; no voltage with a normal diode reading points upstream to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E1_AVDD18_PLL0.3901.800–
AI: what PP1V8_SSD0_S4E1_AVDD18_PLL is and how to check it

PP1V8_SSD0_S4E1_AVDD18_PLL — 820-01958

  • What it is (from the name): a 1.8 V rail feeding the SSD0 section and an AVDD18 PLL supply; the S4E1 part of the name places it in the S4 startup stage. Which parts sit on it isn't known here.
  • Known-good readings: diode 0.390 in diode mode, and 1.800 V with power applied. These come from community contributions and are a guide, not a guarantee.
  • How to check: power off and unplug, then measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or a heavy load on the rail, but one reading doesn't confirm a bad part. No known-good resistance reading exists for this rail, so compare against a matching rail or a known-good board before replacing anything.
PP1V8_SSD0_S4E1_PCI_AVDD_H0.3901.800–
AI: what PP1V8_SSD0_S4E1_PCI_AVDD_H is and how to check it
  • What it is: A 1.8 V rail, from the name: an SSD/PCIe-related supply that comes up in the S4 stage. Which parts sit on it isn't known here.
  • Known-good readings (community guide): diode 0.390 to ground, voltage 1.800.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a low diode reading or a rail pulled down under load usually points to a shorted load or a failed regulator on that rail — confirm with a second measurement before replacing anything.

S3: memory 3

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S30.207––
AI: what PP0V6_S3 is and how to check it

PP0V6_S3 is a 0.6 V rail; the "S3" part of the name indicates the memory (S3) startup stage, and this is from the name only, not from a board file.

  • Known-good: diode-to-ground reading of 0.207 on PP0V6_S3. No known-good voltage reading here.
  • Check it with the board unpowered in diode mode, red probe on ground, black on the rail; then power up and measure the voltage at the rail.
  • A diode reading far below 0.207 usually points to a short or a failing load on the rail; far above it can mean an open path. Treat these as guides, not proof a part is bad.
  • With no known-good voltage listed, compare the powered voltage against what the rail's name implies (about 0.6 V) and against a matching rail on a known-good board.
PP1V1_S30.1631.100–
AI: what PP1V1_S3 is and how to check it

PP1V1_S3 is a 1.1 V rail; the "S3" in its name marks it as a memory-stage supply (from the name). The readings archive lists diode 0.163 and voltage 1.100 for it, with no condition noted, so treat these as a guide only.

  • Check it unpowered: diode mode from PP1V1_S3 to ground, board off.
  • Then power the board and measure the voltage on the rail.
  • A diode reading far from 0.163 suggests a short or leaky part on the rail; a voltage far from 1.100 with a normal diode reading points to the supply not coming up or being loaded down.
  • No known-good resistance reading exists here; compare against a matching rail or a known-good board.
PP1V8_S30.3051.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix indicates the memory stage of startup, from its name. Known-good readings here are diode 0.305 and voltage 1.800, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.305 suggests a short or leak on the rail; a voltage far from 1.800 suggests the rail isn't coming up or is loaded down. No known-good resistance reading is available for this rail.

S0: running 28

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1P05_S0_CPU_VCCPLL0.198––
PP1V1_S0SW_CPU_VCCPLL_OC0.479––
AI: what PP1V1_S0SW_CPU_VCCPLL_OC is and how to check it
  • What it is: From its name, PP1V1_S0SW_CPU_VCCPLL_OC is a 1.1 V CPU power rail (VCCPLL, likely the CPU PLL supply), switched in the S0 running state. The exact parts on it aren't known here.
  • Known-good reading: Diode mode to ground, board unpowered, is 0.479. No known-good voltage reading is available here.
  • How to check: Power off, measure diode to ground on the rail; then power on and measure the rail voltage, comparing against a known-good board since no voltage value is listed.
  • If far off: A diode reading well below 0.479 suggests a short or leaky load on the rail; investigate before replacing parts.
PP1V05_S0_CPU_VCCST0.164––
AI: what PP1V05_S0_CPU_VCCST is and how to check it

PP1V05_S0_CPU_VCCST is a 1.05 V rail; the "S0" in its name marks it as a running-state supply, and "CPU_VCCST" suggests it feeds the CPU's power-status/standby domain (that part is general reading of the name, not from board data). The only known-good figure here is a diode reading of 0.164 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far below 0.164 usually points to a short or leaky load on the rail, while a much higher one can mean an open path; treat the single figure as a guide and compare against a matching rail or a known-good board before condemning anything.

PP1V05_S0_VCCSTG0.210––
AI: what PP1V05_S0_VCCSTG is and how to check it

PP1V05_S0_VCCSTG is a 1.05 V rail; the S0 in its name marks it as a running-state supply, and VCCSTG suggests it feeds storage-related circuitry (from the name, not confirmed by a board file).

  • Known-good: diode 0.210 to ground, from the readings archive; no known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with the board powered and running.
  • A diode reading far from 0.210 usually points to a short or a leaky part on that rail; a correct diode reading with missing voltage points upstream, at the rail's enable or source.
PP1V8_S0_SPKRAMP_AVDD0.320––
AI: what PP1V8_S0_SPKRAMP_AVDD is and how to check it

PP1V8_S0_SPKRAMP_AVDD (820-01958) — reference note

  • From its name, this is a 1.8 V supply rail (PP1V8) for the speaker amplifier's analog supply (SPKRAMP_AVDD), active in the S0 running state.
  • Known-good reading from the archive: diode mode to ground 0.320. This is a community value and a guide only; there is no known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the DC voltage at the rail, expecting about 1.8 V when the board is running.
  • A diode reading far below 0.320 suggests a short or leaky load on the rail; far above it suggests an open path. Confirm with voltage before replacing anything.
PP1V8_S0SW_CPU0.413––
AI: what PP1V8_S0SW_CPU is and how to check it

PP1V8_S0SW_CPU is a 1.8 V rail; the S0 in the name indicates the running state, and SW_CPU suggests it is a switched supply for the CPU. The only known-good figure here is a diode reading of 0.413 to ground. Check it with the board unpowered in diode mode, probe to ground, then confirm the voltage with power applied; no known-good voltage reading is listed. A diode value far from 0.413 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S0SW_LCD0.533––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is the switched 3.3 V LCD rail; the S0 in the name indicates it belongs to the running (S0) state, and SW suggests it is switched on rather than always present. The only known-good reading here is a diode value of 0.533 to ground, with no condition recorded; no known-good voltage reading is available. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.533 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP3V3_TBT_T_S00.501––
AI: what PP3V3_TBT_T_S0 is and how to check it

PP3V3_TBT_T_S0 is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "TBT" suggests it serves the Thunderbolt section (both from the name, not from board data).

  • Known-good reading here: diode 0.501 in diode mode to ground, board unpowered. No known-good voltage reading is recorded for this rail.
  • Check it with the board off: multimeter in diode mode, black probe on ground, red on the rail, and compare with 0.501.
  • Then power the board and measure the voltage on the rail; it should sit near 3.3 V, which is general expectation from the rail name, not a recorded value.
  • A diode reading far below 0.501 usually points to a short or a failing part on the rail; a far higher or open reading suggests a broken connection. Confirm with voltage before replacing anything.
PP3V3_TBT_T_S0_R0.501––
AI: what PP3V3_TBT_T_S0_R is and how to check it

PP3V3_TBT_T_S0_R is a 3.3 V rail for the Thunderbolt section, and the S0 in its name indicates it is up in the running state (both from the name). The only known-good reading here is a diode value of 0.501, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.501 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_TBT_T_S0_SVR0.501––
AI: what PP3V3_TBT_T_S0_SVR is and how to check it

PP3V3_TBT_T_S0_SVR is a 3.3 V rail; from the name it's a Thunderbolt-related supply that comes up in S0 (running) state. The only known-good reading here is a diode value of 0.501 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.501 usually points to a short or a leaky part on that rail, while a much higher reading can mean an open path. Voltage that's missing or low in S0 suggests the rail isn't being enabled or its source supply isn't present, but confirm with the next measurement before replacing anything.

PP3V3_TBT_X_S00.505––
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt section, and the S0 suffix indicates it belongs to the running state (from the name). The only known-good reading here is a diode value of 0.505, with no condition recorded and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.505 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_TBT_X_S0_R0.505––
AI: what PP3V3_TBT_X_S0_R is and how to check it

PP3V3_TBT_X_S0_R is a 3.3 V rail feeding the Thunderbolt (TBT) section, and the S0 in its name indicates it comes up in the running state. From the readings archive, its known-good diode reading to ground is 0.505, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is available here. A diode reading far from 0.505 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_TBT_X_S0_SVR0.505––
AI: what PP3V3_TBT_X_S0_SVR is and how to check it

PP3V3_TBT_X_S0_SVR — from the name, a 3.3 V rail for the Thunderbolt (TBT) section, active in S0 (running) state.

  • Known-good: diode 0.505 to ground (from the readings archive; a community guide, not a factory spec). No known-good voltage reading here.
  • Check: power off, diode mode, black probe to ground, red to the rail — expect around 0.505. Then power on and measure the voltage; no known-good voltage value is listed.
  • A diode reading far below 0.505 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PP5V_S0_BKLT_A0.016––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the 5 V backlight rail that is present in the S0 (running) state, judging from the name. The only known-good reading here is a diode value of 0.016 to ground; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.016.
  • Then power the board and measure the voltage on the rail in the S0 state.

A diode reading far below 0.016 usually points to a short or a leaky load on the rail, but one reading doesn't confirm a bad part. This is a guide from community readings, not a confirmed spec.

PP5V_S0_BKLT_D0.406––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the backlight rail, a 5 V supply that comes up at the S0 (running) stage — both from the name. The archive lists one known-good diode reading, 0.406, with no condition noted. Check it unpowered in diode mode from the rail to ground, then confirm the voltage with the board running. There's no known-good voltage reading here, so compare against a matching rail on a known-good board. A diode reading far from 0.406 usually points to a short or a leaky part on the rail, but one reading isn't proof — check the voltage and the parts on the net before replacing anything.

PP5V_S0_KBD_BKLT_A0.420––
AI: what PP5V_S0_KBD_BKLT_A is and how to check it

PP5V_S0_KBD_BKLT_A is a 5 V rail that, from its name, powers keyboard backlight and is enabled in S0 (running) state. The only known-good reading here is a diode value of 0.420 to ground, with the board unpowered. Check it by measuring diode mode from the net to ground with power off, then measure the voltage with the board powered and running. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.420 usually points to a short or leaky component on that rail, but confirm with the powered voltage before replacing anything.

PP5V_S0_KBD_BKLT_D0.421––
AI: what PP5V_S0_KBD_BKLT_D is and how to check it

PP5V_S0_KBD_BKLT_D (820-01958) — reference note

  • From its name, this is a 5 V rail (PP5V) that is present in the S0 running state and feeds keyboard backlight (KBD_BKLT). The S0 suffix means it should only come up once the board is fully running, not in standby.
  • Known-good from the readings archive: diode mode to ground 0.421. That is the only known-good value recorded here; there is no known-good voltage or resistance reading for this rail.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.421. Then apply power, wake the board into S0, and measure the DC voltage at the rail.
  • A diode reading far below 0.421 suggests a short or leaky load on the rail; far above it suggests an open path or missing connection. Treat one reading as a guide only, since community readings vary with board state, and confirm before replacing anything.
PP5V_S0_KBDBKLT_SW20.4065.100–
AI: what PP5V_S0_KBDBKLT_SW2 is and how to check it
  • What it is: From the name, PP5V_S0_KBDBKLT_SW2 is a 5 V rail that is switched (SW2) and feeds the keyboard backlight (KBDBKLT), active in the S0 running state. The name is the only source for this; the parts on the net aren't known.
  • Known-good readings (community guide): diode 0.406 to ground, voltage 5.100 V with the board running. No known-good resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.406. Then power up and measure the voltage; it should sit near 5.100 V in S0.
  • What a far-off reading suggests: A much lower diode reading points to a short or leaky load on the switched backlight side; a correct diode reading but missing voltage points upstream to the switch or its enable. Treat these as likely causes, not confirmed ones, and check the enable and switch before replacing anything.
PP5V_S0SW_LCD0.553––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is a switched 5 V LCD rail; the S0 in the name indicates it belongs to the running (S0) state, and SW suggests it is switched on by a control signal rather than always present. The only known-good reading here is a diode value of 0.553 to ground on PP5V_S0SW_LCD; no known-good voltage reading is listed. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail once the board is in S0. A diode reading far from 0.553 usually points to a short or a leaky component on the rail, while a correct diode reading with no voltage points toward the switch or its enable signal; treat these as likely causes, not confirmed ones.

PPVCC_S0_CPU0.0291.50034.000R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — reference note

  • What it is: From the name, this is the CPU core power rail (VCC_CPU), active in the S0 running state. It's the main CPU supply, so it comes up late in the power sequence and only after the earlier rails are good.
  • Known-good readings (community guide): diode 0.029, voltage 1.500, resistance 34.000R. These vary with board state, so treat them as a guide, not a spec.
  • How to check: With the board unpowered, measure diode mode to ground on the rail; then apply power and measure the voltage. Compare both against the readings above.
  • If far off: A diode or resistance reading well below known-good usually points to a short or a failing load on the rail, often the CPU or a decoupling part; a missing voltage with a normal diode reading points more toward the rail's supply or enable. No known-good value of any other kind is recorded here.
PPVIN_S0_CPUVR_VIN0.415––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VRM input rail, an S0 (running-state) supply, judging from the name. The archive lists one known-good diode reading of 0.415 to ground; no known-good voltage reading is recorded here.

  • Check with the board unpowered: diode mode, red probe to ground, black to the rail. A far lower reading usually points to a short or a leaky part on that rail; a far higher one to an open path.
  • Then power the board and measure the voltage on the rail, comparing against a known-good board since no voltage value is recorded.
  • One reading alone doesn't condemn a part; confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT0.86513.050–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT is the input supply rail for the LCD backlight switch, active in the S0 (running) state. The board data has no parts list, so which components sit on this net isn't known here.
  • Known-good readings: diode 0.865 and voltage 13.050, from the community archive and only a guide; no condition is recorded.
  • How to check: with the board powered off, measure diode mode from the rail to ground, then power up and measure the voltage on the rail.
  • If far off: a diode reading well below known-good often suggests a short or leaky part on the rail; a voltage far from 13.050 with power applied points to the supply feeding it or the switch not turning on. Confirm with a second reading before replacing anything.
PPVIN_S0SW_LCDBKLT_F0.41013.050–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F is the backlight input rail: "LCDBKLT" points to the display backlight, "PPVIN" to a power input, and "S0" to the running state (from the name). The archive lists a diode reading of 0.410 and a voltage of 13.050 for it; treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A diode reading far from 0.410 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part. No known-good resistance reading is recorded for this rail.

PPVIN_S0SW_LCDBKLT_R0.41013.050–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the LCD backlight input rail; the "S0" in the name indicates it belongs to the running state, and "LCDBKLT" points to the display backlight supply. The archive lists a known-good diode reading of 0.410 to ground and a voltage of 13.050, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.410 usually suggests a short or leaky load on the rail, while a voltage well off 13.050 points to a supply or enable problem upstream; treat these as guides, since the archive has no resistance value for this rail.

PPVOUT_S0_KBDBKLT0.578––
AI: what PPVOUT_S0_KBDBKLT is and how to check it
  • What it is: From the name, PPVOUT_S0_KBDBKLT is a keyboard backlight power output that is present in the S0 (running) state. The exact parts on this net aren't known here.
  • Known-good reading: diode 0.578 to ground, board unpowered. No known-good voltage reading is listed.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage on the rail with the backlight active.
  • If it's far off: a much lower diode reading usually points to a short or a failed component on the rail; a much higher one to an open path. Confirm with a voltage check before replacing anything.
PPVOUT_S0_KBDBKLT_R0.59439.570–
AI: what PPVOUT_S0_KBDBKLT_R is and how to check it
  • What it is: PPVOUT_S0_KBDBKLT_R is a power output rail for the keyboard backlight, from the name (PP = power rail, VOUT = output, S0 = running state, KBDBKLT = keyboard backlight). It's a boosted rail, judging by the high voltage.
  • Known-good readings (community archive, a guide only): diode 0.594 to ground, and 39.570 V with the board powered and running.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • What a far-off reading suggests: a much lower voltage with power on points to the backlight circuit not being enabled or a fault in that supply; a low or shorted diode reading suggests a short on the rail. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning a part.
PPVOUT_S0_LCDBKLT1.193––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT (820-01958) — From the name, this is the S0 (running-state) output rail feeding the LCD backlight; the "PPVOUT" prefix marks it as a switched power output.

  • Known-good reading: diode 1.193 (from the readings archive, no condition noted). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far from known-good: a diode reading well below 1.193 usually points to a short or leaky load on the backlight output; a high or open reading can mean a broken feed. Confirm with the voltage measurement before replacing anything.
PPVOUT_S0_LCDBKLT_F1.19346.000–
AI: what PPVOUT_S0_LCDBKLT_F is and how to check it
  • What it is: From the name, PPVOUT_S0_LCDBKLT_F is the display backlight output rail, active in the S0 (running) state. It's the boost-converter output feeding the LCD backlight string.
  • Known-good readings (community archive, guide only): diode mode 1.193, voltage 46.000 V. No resistance reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: A low diode reading or a rail that won't come up usually points to a short or a fault in the backlight boost circuit or its load, but one reading doesn't confirm a bad part. Compare against a known-good board before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
AGND_P1V8PRIM0.000––
ALL_SYS_PWRGD0.7110.000 DFU%2bMode–
AON_SLEEP1_RESET_L0.404––
AUD_PWR_EN0.754––
BKLT_EN_R0.537––
BKLT_SD0.597––
BKLT_SENSE_OUT0.730––
BT_AUDIO_SYNC0.515––
BT_PWR_EN0.759––
CHGR_AUX_DET0.630––
CHGR_BGATE0.618––
CHGR_BMON0.600––
CHGR_BOOT10.586––
CHGR_BOOT1_RC0.587––
CHGR_BOOT20.582––
CHGR_BOOT2_RC0.583––
CHGR_COMP0.630––
CHGR_CSI_N0.54220.000–
CHGR_CSI_P0.54220.000–
CHGR_CSIR_N0.534––
CHGR_CSIR_P0.534––
CHGR_CSO_N0.41013.050–
CHGR_CSO_P0.41013.050–
CHGR_CSOR_N0.480––
CHGR_CSOR_P0.480––
CHGR_EN_MVR0.5315.000–
CHGR_EN_MVR_R0.5315.000–
CHGR_HPWR_EN_L0.000––
CHGR_LX10.494––
CHGR_LX20.494––
CHGR_PHASE10.49013.050–
CHGR_PHASE20.49013.050–
CHGR_RST_IN0.601––
CHGR_RST_IN_R0.600––
CHGR_VBAT0.622––
CODEC_INT_L0.460––
CODEC_RESET_L0.459––
CODEC_WAKE_L0.457––
COMP_A_CPUCORE0.611––
COMP_A_CPUCORE_L2.080––
CORE_ISUMN_R1.270––
CPU_C10_GATE_L0.514––
CPU_CATERR_L0.188––
CPU_DDR_RCOMP<0>0.083––
CPU_PECI0.262––
CPU_POPI_RCOMP0.042––
CPU_PROCHOT_L0.437––
CPU_PROCHOT_R_L0.293––
CPU_PROCHOT_RS_L0.441––
CPU_SMC_THRMTRIP_L0.459––
CPU_VCCSENSE_N0.001––
CPU_VCCSENSE_P0.029––
CPU_VIDALERT_L0.245––
CPU_VIDSCLK0.200––
CPU_VIDSOUT0.191––
CPU_VR_EN0.582––
CPU_VR_EN_R0.582––
CPU_VR_PROCHOT_L0.502––
CPUCORE_BOOT10.550––
CPUCORE_BOOT20.550––
CPUCORE_BOOT30.550––
CPUCORE_BP10.550––
CPUCORE_BP20.550––
CPUCORE_BP30.550––
CPUCORE_CGND10.000––
CPUCORE_CGND20.000––
CPUCORE_CGND30.000––
CPUCORE_FCCM0.583––
CPUCORE_ISEN10.613––
CPUCORE_ISEN20.612––
CPUCORE_ISEN30.640––
CPUCORE_ISNS1_N0.0291.50034.000R
CPUCORE_ISNS1_P0.0291.50034.000R
CPUCORE_ISNS2_N0.0291.50034.000R
CPUCORE_ISNS2_P0.0291.50034.000R
CPUCORE_ISNS3_N0.0291.50034.000R
CPUCORE_ISNS3_P0.0291.50034.000R
CPUCORE_ISUMN0.270––
CPUCORE_ISUMN_R0.316––
CPUCORE_ISUMP0.308––
CPUCORE_PHASE10.269––
CPUCORE_PHASE20.278––
CPUCORE_PHASE30.278––
CPUCORE_PWM10.598––
CPUCORE_PWM20.598––
CPUCORE_PWM30.597––
CPUCORE_SW10.0291.50034.000R
CPUCORE_SW20.0291.50034.000R
CPUCORE_SW30.0291.50034.000R
CPUVR_PGOOD0.581––
CPUVR_VIDALERT_L_R0.245––
CPUVR_VIDSCLK_R0.200––
CPUVR_VIDSOUT_R0.200––
CPUVSENSE_IN0.270––
DISP_RCOMP0.147––
DP_INT_AUXCH_C_N0.372––
DP_INT_AUXCH_C_P0.357––
DP_INT_HPD0.807––
DP_INT_ML_C_N<0>0.320––
DP_INT_ML_C_N<1>0.315––
DP_INT_ML_C_N<2>0.317––
DP_INT_ML_C_N<3>0.318––
DP_INT_ML_C_P<0>0.315––
DP_INT_ML_C_P<1>0.310––
DP_INT_ML_C_P<2>0.312––
DP_INT_ML_C_P<3>0.315––
DP_T_HST_HPD0.694––
EDP_BKLT_EN0.537––
EDP_BKLT_PWM0.802––
EDP_PANEL_PWR_BUF_EN0.705––
EDP_PANEL_PWR_DLY_EN0.630––
EDP_PANEL_PWR_EN0.539––
ESPI_RESET_L0.451––
FAN_LT_PWM0.723––
FAN_LT_TACHOL––
FB_A_CORE_R2.060––
FB_A_CPUCORE0.584––
FB_CORE_R0.272––
I2C_ALS_SCL0.466––
I2C_ALS_SCL_CONN0.498––
I2C_ALS_SDA0.465––
I2C_ALS_SDA_CONN0.498––
I2C_BKLT_SCL0.5335.000–
I2C_BKLT_SCL_R0.524––
I2C_BKLT_SDA0.5325.000–
I2C_BKLT_SDA_R0.523––
I2C_DISP_LS_EN0.480––
I2C_FTCAM_ISOL_SCL0.704––
I2C_FTCAM_ISOL_SDA0.611––
I2C_FTCAM_SCL0.449––
I2C_FTCAM_SCL_CONN0.540––
I2C_FTCAM_SDA0.449––
I2C_FTCAM_SDA_CONN0.540––
I2C_PMU_SCL_R0.4561.800 DFU%2bMode–
I2C_PMU_SDA_R0.4531.800 DFU%2bMode–
I2C_PWR_SCL0.4561.800 DFU%2bMode–
I2C_PWR_SDA0.4531.800 DFU%2bMode–
I2C_SEP_SCL0.4581.800 DFU%2bMode1.800–
I2C_SEP_SDA0.4561.800 DFU%2bMode1.800–
I2C_SNS_G3S_SCL0.452––
I2C_SNS_G3S_SDA0.451––
I2C_SNS1_S0_SCL0.470––
I2C_SPKRAMP_L_SCL0.386––
I2C_SPKRAMP_L_SDA0.385––
I2C_SPKRAMP_R_SCL0.455––
I2C_SPKRAMP_R_SDA0.455––
I2C_TCON_SCL0.520––
I2C_TCON_SCL_CONN0.546––
I2C_TCON_SCL_R0.480––
I2C_TCON_SDA0.513––
I2C_TCON_SDA_CONN0.546––
I2C_TCON_SDA_R0.480––
I2C_TPAD_3V3_SCL0.892––
I2C_TPAD_3V3_SCL_R0.920––
I2C_TPAD_3V3_SDA0.922––
I2C_TPAD_3V3_SDA_R0.934––
I2C_TPAD_SDA_R0.500––
I2C_UPC_SCL0.454––
I2C_UPC_SDA0.453––
I2C_UPC_T_INTM_L0.600––
I2C_UPC_T_SCLM0.560––
I2C_UPC_T_SDAM0.560––
I2C_UPC_X_INTM_L0.019––
I2C_UPC_X_SCLM0.553––
I2C_UPC_X_SDAM0.554––
I2S_CODEC_BCLK0.476––
I2S_CODEC_BCLK_R0.460––
I2S_CODEC_D2R0.459––
I2S_CODEC_LRCLK0.459––
I2S_CODEC_R2D0.476––
I2S_SPKRAMP_L_BCLK0.386––
I2S_SPKRAMP_L_BCLK_R0.399––
I2S_SPKRAMP_L_D2R0.405––
I2S_SPKRAMP_L_D2R_R0.407––
I2S_SPKRAMP_L_LRCLK_R0.385––
I2S_SPKRAMP_L_R2D0.386––
I2S_SPKRAMP_R_BCLK0.473––
I2S_SPKRAMP_R_LRCLK_R0.472––
I2S_SPKRAMP_R_R2D0.473––
IMON_A_CPUCORE0.612––
IPD_LID_OPEN0.690––
ISNS_3V3G3HMAIN_NOL––
ISNS_3V3G3HMAIN_POL––
ISNS_5VG3S_NOL––
ISNS_5VG3S_POL––
ISNS_HS_COMPUTING_IOUT0.710––
ISNS_HS_COMPUTING_N0.41013.050–
ISNS_HS_COMPUTING_P0.41013.050–
ISNS_LCDBKLT_N0.41013.050–
ISNS_LCDBKLT_P0.41013.050–
ISNS_MEM0V6_N0.366––
ISNS_MEM0V6_P0.366––
ISNS_MEM1V1_NOL––
ISNS_MEM1V1_POL––
ISNS_P1V05_PCH_EXT_N0.470––
ISNS_P1V05_PCH_EXT_P0.470––
ISNS_P1V05_PCH_VNN_EXT_N0.481––
ISNS_P1V05_PCH_VNN_EXT_P0.485––
ISNS_SPKRL_N0.41013.050–
ISNS_SPKRL_P0.41013.050–
ISNS_SSD0_NOL––
ISNS_SSD0_POL––
ISNS_VCCINAUX_IOUT0.700––
ISNS_VCCINAUX_N0.225––
ISNS_VCCINAUX_P0.225––
ISNS_VDDMAIN_NOL––
ISNS_VDDMAIN_POL––
ISNS_WLANBT_N0.378––
ISNS_WLANBT_P0.378––
JTAG_ISP_TCK0.533––
JTAG_ISP_TDI0.530––
JTAG_ISP_TDO0.534––
JTAG_TBT_T_TMS0.5503.200–
JTAG_TBT_X_TMS0.567––
KBD_BKLT_PWM0.512––
KBD_BKLT_SENSE_OUT0.714––
KBDBKLT_FB20.594––
KBDBKLT_ISET0.666––
KBDBKLT_KEYB10.645––
KBDBKLT_KEYB20.641––
KBDLED_CATHODE10.648––
KBDLED_CATHODE20.628––
LCD_PWR_SLEW0.700––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.730––
LCDBKLT_FET_DRV0.513––
LCDBKLT_FET_DRV_R0.522––
LCDBKLT_SW0.429––
LCDBKLT_TB_XWR1.193––
LDO_CORE0.370––
LDO_RTC–1.500 DFU%2bMode–
LID_CTRL_DMIC0.707––
LID_OPEN_LEFT0.450––
LID_OPEN_RIGHT0.450––
MEM_RESET_L0.473––
MESA_INT0.462––
MESA_PWR_EN0.459––
MIPI_FTCAM_CLK_CONN_N0.513––
MIPI_FTCAM_CLK_CONN_P0.513––
MIPI_FTCAM_CLK_F_N0.513––
MIPI_FTCAM_CLK_F_P0.513––
MIPI_FTCAM_CLK_ISOL_N0.513––
MIPI_FTCAM_CLK_ISOL_P0.513––
MIPI_FTCAM_CLK_N0.470––
MIPI_FTCAM_CLK_P0.470––
MIPI_FTCAM_DATA_CONN_N<0>0.516––
MIPI_FTCAM_DATA_CONN_P<0>0.516––
MIPI_FTCAM_DATA_F_N<0>0.516––
MIPI_FTCAM_DATA_F_P<0>0.516––
MIPI_FTCAM_DATA_ISOL_N<0>0.516––
MIPI_FTCAM_DATA_ISOL_P<0>0.516––
MIPI_FTCAM_DATA_N<0>0.470––
NAND_DISCHARGE_EN0.747––
NAND_DISCHARGE_EN_RCOL––
NAND_MODE_1V2_EN0.750––
NAND_RESET_L0.4511.800–
NANDVSENSE_IN0.370––
NTC_A_CPUCORE0.615––
NTC_A_CPUCORE_RN0.000––
NTC_A_CPUCORE_RPOL––
P0V6_S3_COMP0.688––
P0V6_S3_COMP_RCOL––
P0V6_S3_EN0.511––
P0V6_S3_FB0.315––
P0V6_S3_FB_R0.226––
P0V6_S3_SKIP0.540––
P0V6_S3_SS0.590––
P0V6_S3_SW0.207––
P0V8SLPDDR_FB0.032––
P0V8SLPDDR_FB_R0.032––
P0V8SLPDDR_SW00.032 DFU%2bMode0.0320.827 DFU%2bMode0.827 DFU+Mode0.82031.900R DFU%2bMode31.900R
P0V8SLPDDR_SW10.032 DFU%2bMode0.0320.827 DFU%2bMode0.824 DFU+Mode0.82031.900R DFU%2bMode31.900R
P0V9SLPDDR_FB0.053––
P0V9SLPDDR_FB_R0.053––
P0V9SLPDDR_SW00.043 DFU%2bMode0.0430.900 DFU%2bMode0.900 DFU+Mode0.90051.000R DFU%2bMode51.000R
P0V9SLPDDR_SW10.043 DFU%2bMode0.0430.900 DFU%2bMode0.900 DFU+Mode0.90051.000R DFU%2bMode51.000R
P0V9SSD_FB_N0.001––
P0V9SSD_FB_N_GND0.001––
P0V9SSD_FB_P0.430––
P0V9SSD_SW00.382 DFU%2bMode0.3820.000 DFU+Mode0.900106.500 DFU%2bMode106.500
P1V1_BOOT_RC0.534––
P1V1_DRVH0.677––
P1V1_DRVH_R0.677––
P1V1_DRVL0.458––
P1V1_DRVL_R0.458––
P1V1_PHASE0.1631.100–
P1V1_S3_EN0.499––
P1V1_S3_EN_R0.499––
P1V1_S3_PGOOD0.511––
P1V1_SLPDDR_SOCFET_EN0.5531.800–
P1V1_SNSOL––
P1V1_SNS_R0.163––
P1V1_SW0.180––
P1V1_VBST0.530––
P1V1REG_AGND0.000––
P1V1REG_MODE0.540––
P1V1REG_REFIN0.690––
P1V1REG_TRIP0.547––
P1V1REG_VREF0.627––
P1V1REG_VREF_ROL––
P1V1S0SW_FET_EN0.516––
P1V1SLPDDR_RAMP0.630––
P1V1SLPS2R_FB0.257––
P1V1SLPS2R_SW00.257 DFU%2bMode0.2571.100 DFU+Mode1.100–
P1V1SLPS2R_SW10.257 DFU%2bMode0.2571.100 DFU+Mode1.1000.000R
P1V05_PCH_EXT_FB0.500––
P1V05_PCH_EXT_FB_R0.500––
P1V05_PCH_EXT_SW00.034 DFU%2bMode0.4700.000 DFU+Mode1.05033.500R DFU%2bMode33.500R
P1V05_PCH_EXT_SW10.034 DFU%2bMode0.4700.000 DFU+Mode33.500R DFU%2bMode
P1V05_VCCST_EN0.623––
P1V05_VCCST_EN_R0.644––
P1V8_G3S_DSCHG0.320––
P1V8G3S_DSCHG_EN0.460––
P1V8G3S_DSCHG_EN_L0.572––
P1V8G3S_EN0.553––
P1V8G3S_SS0.640––
P1V8PRIM_AVIN0.49012.500–
P1V8PRIM_EN0.5453.300–
P1V8PRIM_FB1.400––
P1V8PRIM_FB_R1.940––
P1V8PRIM_FB_TOP0.253––
P1V8PRIM_PGOOD0.450––
P1V8PRIM_PHASE0.2801.800–
P1V8PRIM_PHASE_B0.2801.800–
P1V8PRIM_SS0.750––
P1V8PRIM_VOS0.263––
P1V8SLPS2R_FB0.420––
P1V8SLPS2R_SW00.420 DFU%2bMode0.4201.800 DFU+Mode1.800–
P1V8SSD_FB0.390––
P1V8SSD_SW00.388 DFU%2bMode0.3880.000 DFU+Mode0.900–
P2V7_SSD_DISCHARGE0.323––
P3V3G3H_COMP20.726––
P3V3G3H_COMP2_ROL––
P3V3G3H_CS2_L_N0.3733.300–
P3V3G3H_CS2_L_P0.3773.300–
P3V3G3H_CSP21.264––
P3V3G3H_DRVH0.930––
P3V3G3H_DRVH_R0.930––
P3V3G3H_DRVL0.550––
P3V3G3H_DRVL_R0.550––
P3V3G3H_RF0.588––
P3V3G3H_SW0.369––
P3V3G3H_VBST0.560––
P3V3G3H_VBST_R0.627––
P3V3G3H_VFB20.568––
P3V3G3H_VFB2_R0.363––
P3V3G3H_VFB2_R20.371––
P3V3G3H_VFB2_RROL––
P3V3G3H_VSW0.367 DFU%2bMode0.3673.300–
P3V3G3S_EN0.552––
P3V3MAIN_PGOOD0.5573.300–
P3V3RTC_AVIN0.490––
P3V3RTC_FB1.398––
P3V3RTC_FB_ROL––
P3V3RTC_FB_TOP0.411––
P3V3RTC_PGOOD0.511––
P3V3RTC_PHASE0.4623.300–
P3V3RTC_SS0.750––
P3V3RTC_VOS0.419––
P3V3SEN_SS0.620––
P3V3TBT_T_RAMP0.620––
P3V3TBT_X_RAMP0.612––
P5V_G3S_DISCHARGE0.163––
P5VG3S_COMP10.726––
P5VG3S_COMP1_ROL––
P5VG3S_CS1_L_N0.006––
P5VG3S_CS1_L_P0.006––
P5VG3S_CSP10.935––
P5VG3S_DRVH0.640––
P5VG3S_DRVH_R0.640––
P5VG3S_DRVL0.550––
P5VG3S_DRVL_R0.550––
P5VG3S_DSCHRG_EN0.451––
P5VG3S_DSCHRG_ROL––
P5VG3S_DSCHRG_RC0.480––
P5VG3S_EN0.560––
P5VG3S_EN_DLY0.506––
P5VG3S_EN_R0.560––
P5VG3S_PGOOD0.5631.800–
P5VG3S_SW0.006––
P5VG3S_VBST0.560––
P5VG3S_VBST_R0.561––
P5VG3S_VFB10.562––
P5VG3S_VFB1_R0.412––
P5VG3S_VFB1_R20.421––
P5VG3S_VFB1_RROL––
P5VG3S_VSW0.4065.000–
P5VP3V3_SKIPSEL0.480––
P5VP3V3_VREF20.469––
P5VP3V3_VREG30.514––
P5VXX_EN0.590––
PANEL_P3V3_EN0.552––
PANEL_P5V_EN0.553––
PANEL_P5V_EN_D0.970––
PBUS_DIVIDER0.700––
PBUS_DIVIDER_OUT0.650––
PBUS_DIVIDER_REF0.665––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.480––
PBUSVSENS_EN_L0.500––
PBUSVSENS_EN_L_DIVOL––
PCH_BATLOW_L0.799––
PCH_BSB_FORCE_PWR0.680––
PCH_CORE_VID00.548––
PCH_CORE_VID10.549––
PCH_DIFFCLK_BIASREF0.060––
PCH_OPI_RCOMP0.050––
PCH_PCIE_RCOMP_N0.344––
PCH_PCIE_RCOMP_P0.344––
PCH_PCIE_WAKE_L0.799––
PCH_PWRBTN_L0.719––
PCH_RTC_RESET_L0.748––
PCH_UART_DEBUG_D2R0.681––
PCH_UART_DEBUG_R2D0.678––
PCH_USB2_COMP0.115––
PCH_VCCINSENSE_N0.001––
PCH_VCCINSENSE_P0.215––
PCH_VCCINSENSE_P_R0.265––
PCIE_CLK100M_PCH_WLAN_N0.325––
PCIE_CLK100M_PCH_WLAN_P0.327––
PCIE_PME_L0.529––
PCIE_SSD0_D2R_C_N<0>0.350––
PCIE_SSD0_D2R_C_N<1>0.350––
PCIE_SSD0_D2R_C_P<0>0.350––
PCIE_SSD0_D2R_C_P<1>0.350––
PCIE_SSD0_D2R_N<0>0.400––
PCIE_SSD0_D2R_N<1>0.400––
PCIE_SSD0_D2R_P<0>0.400––
PCIE_SSD0_D2R_P<1>0.400––
PCIE_SSD0_R2D_C_N<0>0.330––
PCIE_SSD0_R2D_C_N<1>0.340––
PCIE_SSD0_R2D_C_P<0>0.330––
PCIE_SSD0_R2D_C_P<1>0.340––
PCIE_SSD0_R2D_N<0>0.410––
PCIE_SSD0_R2D_N<1>0.420––
PCIE_SSD0_R2D_P<0>0.410––
PCIE_SSD0_R2D_P<1>0.420––
PD_P1V1_S3_EN0.520––
PD_PVCCPLLOC_EN0.750––
PD_UPC_X_GPIO10.655––
PD_UPC_X_GPIO90.700––
PD_UPC_X_GPIO100.710––
PDM_DMIC_CLK00.475––
PDM_DMIC_CLK10.473––
PDM_DMIC_DATA00.457––
PDM_DMIC_DATA0_ISOL0.787––
PDM_DMIC_DATA0_R0.510––
PDM_DMIC_DATA10.457––
PDM_DMIC_DATA1_ISOL0.786––
PDM_DMIC_DATA1_R0.500––
PLT_RST_3V3_L0.579––
PLT_RST_L0.546––
PM_PCH_DPWROK0.507––
PM_PCH_PWROK0.736––
PM_PCH_PWROK_SMC0.481––
PM_PCH_SYS_PWROK0.535––
PM_RSMRST_L0.6943.300–
PM_RSMRST_L_RC_SCB0.6043.300–
PM_RSMRST_R_L0.640––
PM_SLP_S0_1V8_L0.470––
PM_SLP_S0_L0.4993.300–
PM_SLP_S3_L0.5463.300–
PM_SLP_S4_L0.7983.300–
PM_SLP_S5_L0.7983.300–
PM_SLP_SUS_L0.5453.300–
PM_SYSRST_L0.797––
PM_SYSRST_R_L0.650––
PM_THRMTRIP_L0.255––
PMU_ACTIVE_READY0.458––
PMU_CLK32K_PCH0.800––
PMU_CLK32K_PCH_R0.750––
PMU_CLK32K_SOC0.4700.867–
PMU_CLK32K_SOC_R0.4840.867–
PMU_CLK32K_WLANBT0.465––
PMU_CLK32K_WLANBT_R0.454––
PMU_COLD_RESET_L0.4511.800–
PMU_CPU_VSENSE0.575––
PMU_DROOP_L0.4771.800 DFU%2bMode–
PMU_FORCE_DFU0.760––
PMU_IREF0.7551.170 DFU%2bMode–
PMU_LCDBKLT_ISENSE0.580––
PMU_LDO3_OUT0.5901.800 DFU%2bMode–
PMU_MEM0V6_ISENSE0.580––
PMU_MEM1V1_ISENSE0.580––
PMU_NAND_VSENSE0.570––
PMU_ONOFF_L0.561––
PMU_ONOFF_R_L0.560––
PMU_ONOFF_R_L_CONN0.560––
PMU_PVDDMAIN_EN0.752––
PMU_RSLOC_RST_L0.6533.200–
PMU_SYS_ALIVE0.3971.800–
PMU_SYS_ALIVE_R0.397––
PMU_VCCINAUX_ISENSE0.570––
PMU_VCCINAUX_VSENSE0.574––
PMU_VDD_HI0.6323.400–
PMU_VDD_MAX0.5503.300 DFU%2bMode–
PMU_VDDMAIN_ISENSE0.580––
PMU_VPUMP0.5805.000 DFU%2bMode–
PMU_WLANBT_ISENSE0.580––
PMU_XTAL10.7900.040 DFU%2bMode–
PMU_XTAL1_R0.8000.120 DFU%2bMode–
PMU_XTAL20.7900.750 DFU%2bMode–
PP0V6_S30.207––
PP0V8_SLPS2R0.1850.800 DFU%2bMode–
PP0V9_SLPDDR0.043 DFU%2bMode0.0430.900 DFU%2bMode0.90051.000R DFU%2bMode51.000R
PP0V9_SLPDDR_SOC_PCIEREFBUF0.043––
PP0V9_SSD00.382 DFU%2bMode0.3820.000 DFU%2bMode0.900106.500 DFU%2bMode106.500
PP0V9_SSD0_S4E0_VDD_PLL0.430––
PP0V9_SSD0_S4E1_VDD_PLL0.425––
PP0V9_TBT_T_LC0.360––
PP0V9_TBT_T_LVR0.5100.900–
PP0V9_TBT_T_SVR0.3510.900–
PP0V9_TBT_T_SVR_IND0.3510.900–
PP0V9_TBT_X_LC0.340––
PP0V9_TBT_X_LVR0.509––
PP0V9_TBT_X_SVR0.3680.900–
PP0V9_TBT_X_SVR_IND0.3680.900–
PP0V82_SLPDDR0.032 DFU%2bMode0.0320.827 DFU%2bMode0.82031.900R DFU%2bMode31.900R
PP1P05_S0_CPU_VCCPLL0.198––
PP1SR3V3_G3H_P0V6_S3_VIN0.377––
PP1V1_S0SW_CPU_VCCPLL_OC0.479––
PP1V1_S30.1631.100–
PP1V1_SLPDDR0.3361.100–
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.360––
PP1V1_SLPDDR_SOC_XTAL_F0.336––
PP1V1_SLPS2R0.257 DFU%2bMode0.2571.100 DFU%2bMode1.1000.000R
PP1V2_AWAKE0.5071.200 DFU%2bMode–
PP1V2_AWAKE_SOC_PCIEPLL_F0.523––
PP1V2_AWAKE_SOC_PCIEREFBUF_F0.507––
PP1V2_AWAKE_SOC_PLLCPU_F0.522––
PP1V2_AWAKE_SOC_PLLSOC_F0.520––
PP1V05_PCH_CPU0.167––
PP1V05_PCH_EXT0.470––
PP1V05_PCH_EXT_REG0.034 DFU%2bMode0.4700.000 DFU+Mode1.05033.500R DFU%2bMode33.500R
PP1V05_S0_CPU_VCCST0.164––
PP1V05_S0_VCCSTG0.210––
PP1V5_UPC_T_LDO_CORE0.5201.500–
PP1V5_UPC_X_LDO_CORE0.5181.500–
PP1V05_VCCST_OUT0.175––
PP1V05_VCCSTG_OUT0.209––
PP1V8_AWAKE0.3881.800 DFU%2bMode1.800–
PP1V8_AWAKE_SOC_FMON_F0.450––
PP1V8_AWAKE_SOC_TSADC_RC0.400––
PP1V8_G3S0.306––
PP1V8_G3S_THMSNS_R0.320––
PP1V8_PCH_CLKLDO0.280––
PP1V8_PCH_CLKLDO_R0.252––
PP1V8_PRIM_PCH0.2801.800–
PP1V8_S0_SPKRAMP_AVDD0.320––
PP1V8_S0SW_CPU0.413––
PP1V8_S30.3051.800–
PP1V8_SLPS2R0.420 DFU%2bMode0.4201.800 DFU+Mode1.800–
PP1V8_SLPS2R_PMUVDDGPIO0.711––
PP1V8_SLPS2R_SOC_LPADC_RC0.450––
PP1V8_SLPS2R_SOC_LPOSC_RC0.460––
PP1V8_SSD0_S4E0_AVDD18_PLL0.3901.800–
PP1V8_SSD0_S4E0_PCI_AVDD_H0.3901.800–
PP1V8_SSD0_S4E1_AVDD18_PLL0.3901.800–
PP1V8_SSD0_S4E1_PCI_AVDD_H0.3901.800–
PP1V8_VCCQIO_SSD00.316––
PP1V8SW_VCCQIO_SSD00.738––
PP1V25_SLPS2R_SMC_AVREF0.573––
PP3V_G3H0.515––
PP3V3_AWAKE0.6263.300–
PP3V3_G3H0.367 DFU%2bMode0.3633.300 DFU+Mode3.300–
PP3V3_G3H_IPD_F0.359––
PP3V3_G3H_PMU_VDDMAIN0.367 DFU%2bMode0.3633.300 DFU+Mode3.300–
PP3V3_G3H_PMU_VINRTC_R0.420––
PP3V3_G3H_RTC0.4103.300–
PP3V3_G3H_RTC_R0.4623.300–
PP3V3_G3S0.379––
PP3V3_G3S_G3H_RIO0.361––
PP3V3_G3S_IPD_F0.379––
PP3V3_G3S_WLANBT0.378––
PP3V3_G3SSW_SNS0.540––
PP3V3_S0SW_LCD0.533––
PP3V3_S50.347––
PP3V3_TBT_T_ANA0.560––
PP3V3_TBT_T_LC0.570––
PP3V3_TBT_T_S00.501––
PP3V3_TBT_T_S0_R0.501––
PP3V3_TBT_T_S0_SVR0.501––
PP3V3_TBT_T_SW0.380––
PP3V3_TBT_T_SX0.501––
PP3V3_TBT_T_VCCA0.520––
PP3V3_TBT_X_ANA0.555––
PP3V3_TBT_X_LC0.570––
PP3V3_TBT_X_S00.505––
PP3V3_TBT_X_S0_R0.505––
PP3V3_TBT_X_S0_SVR0.505––
PP3V3_TBT_X_SW0.370––
PP3V3_TBT_X_SX0.505––
PP3V3_TBT_X_VCCA0.518––
PP3V3_UPC_T_LDO0.5103.300–
PP3V3_UPC_T_VOUTLV0.528––
PP3V3_UPC_X_LDO0.4833.300–
PP3V3_UPC_X_VOUTLV0.529––
PP5V_COREVR_VCC0.409––
PP5V_G3S0.4065.000–
PP5V_G3S_IPD_F0.406––
PP5V_G3S_P1V1REG0.008––
PP5V_MAIN_ALSCAM_F0.406––
PP5V_MAIN_VCORE10.007––
PP5V_MAIN_VCORE20.007––
PP5V_MAIN_VCORE30.007––
PP5V_S0_BKLT_A0.016––
PP5V_S0_BKLT_D0.406––
PP5V_S0_KBD_BKLT_A0.420––
PP5V_S0_KBD_BKLT_D0.421––
PP5V_S0_KBDBKLT_SW20.4065.100–
PP5V_S0SW_LCD0.553––
PP5V_S5_LDO0.469––
PP20V_USBC_T_VBUS0.12420.000–
PP20V_USBC_X_VBUS0.12520.000–
PPBUS_G3H0.41013.050–
PPBUS_G3H_SPKRL0.41013.050–
PPBUS_G3H_SSD00.41013.050–
PPBUS_G3H_TPAD_FLT0.42212.500–
PPBUS_HS_CPU0.41013.050–
PPCHGR_VDDA0.455––
PPCHGR_VDDP0.453––
PPDCIN_G3H0.54220.000–
PPDCIN_G3H_CHGR_AMON0.54220.000–
PPHV_INT_T_G3H0.54220.000–
PPHV_INT_X_G3H0.54220.000–
PPVBAT_G3H_CHGR_R0.41013.050–
PPVBAT_G3H_CONN1.38913.050–
PPVBAT_G3H_FUSE1.38913.050–
PPVCC_CPU_PH10.0291.50034.000R
PPVCC_CPU_PH20.0291.50034.000R
PPVCC_CPU_PH30.0291.50034.000R
PPVCC_NAND_SSD00.3232.500–
PPVCC_S0_CPU0.0291.50034.000R
PPVCCIN_AUX_PCH0.1221.800143.000
PPVCCINAUX_PVCC0.480––
PPVCCINAUX_VCC0.008––
PPVCCIO_OUT0.109––
PPVCCQ_ANI_SSD00.388 DFU%2bMode0.3880.000 DFU%2bMode0.900–
PPVDDCPU_AWAKE0.011 DFU%2bMode0.0110.755 DFU%2bMode1.06010.800R DFU%2bMode10.800R
PPVDDCPUSRAM_AWAKE0.300 DFU%2bMode0.3000.800 DFU%2bMode0.820297.000 DFU%2bMode297.000R
PPVIN_G3H_P1V1_S30.410––
PPVIN_G3H_P3V3G3H0.41013.050–
PPVIN_G3H_P3V3G3HRTC0.48012.500–
PPVIN_G3H_P5VG3S0.41013.050–
PPVIN_S0_CPUVR_VIN0.415––
PPVIN_S0SW_LCDBKLT0.86513.050–
PPVIN_S0SW_LCDBKLT_F0.41013.050–
PPVIN_S0SW_LCDBKLT_R0.41013.050–
PPVIN_SW_LCDBKLT_SW0.86513.050–
PPVNN_PCH_EXT0.481––
PPVNN_PCH_EXT_REG0.058 DFU%2bMode0.0580.000 DFU%2bMode0.90057.000R DFU%2bMode57.000R
PPVOUT_S0_KBDBKLT0.578––
PPVOUT_S0_KBDBKLT_R0.59439.570–
PPVOUT_S0_LCDBKLT1.193––
PPVOUT_S0_LCDBKLT_F1.19346.000–
PPVTT_VTTREF0.475––
PROG1_CPUCOREVR0.610––
PROG2_CPUCOREVR0.611––
PROG3_CPUCOREVR0.632––
PROG4_CPUCOREVR0.613––
PROG5_CPUCOREVR0.633––
PU_U8510_40.715––
PU_U8510_120.720––
PVCCINAUX_DSCHG0.262––
PVCCINAUX_DSCHG_EN0.460––
PVCCINAUX_DSCHG_EN_L0.450––
PVCCNAND_EN0.549––
PVCCNAND_PGOOD0.5082.400–
PVCCSSD0_AVIN0.480––
PVCCSSD0_EN0.549––
PVCCSSD0_FB1.390––
PVCCSSD0_FB_R1.366––
PVCCSSD0_FB_TOP0.323––
PVCCSSD0_PHASE0.3232.500–
PVCCSSD0_SS0.750––
PVCCSSD0_VOS0.331––
PVCCST_EN0.752––
PVCCST_EN_R0.564––
PVDDCPUAWAKE_FB0.011––
PVDDCPUAWAKE_SW00.011 DFU%2bMode0.0110.755 DFU%2bMode0.755 DFU+Mode1.06010.800R DFU%2bMode10.800R
PVDDCPUAWAKE_SW10.011 DFU%2bMode0.0110.755 DFU+Mode1.06010.800R DFU%2bMode10.800R
PVDDCPUAWAKE_SW20.011 DFU%2bMode0.0110.755 DFU+Mode1.06010.800R DFU%2bMode10.800R
PVDDCPUAWAKE_SW30.011 DFU%2bMode0.0110.755 DFU%2bMode0.755 DFU+Mode1.06010.800R DFU%2bMode10.800R
PVDDCPUSRAMAWAKE_FB0.300––
PVDDCPUSRAMAWAKE_SW00.300 DFU%2bMode0.3000.800 DFU%2bMode0.800 DFU+Mode0.820297.000 DFU%2bMode297.000
PVDDQ_EN0.501––
PVDDQ_EN_IN0.580––
PVDDQ_EN_IN_R0.580––
PVDDQ_PGOOD0.597––
PVNN_PCH_EXT_FB_N0.001––
PVNN_PCH_EXT_FB_P0.510––
PVNN_PCH_EXT_FB_R_N0.001––
PVNN_PCH_EXT_FB_R_P0.510––
PVNN_PCH_EXT_SW00.058 DFU%2bMode0.0580.000 DFU+Mode0.90057.000R DFU%2bMode57.000R
PVNN_PCH_EXT_SW10.058 DFU%2bMode0.0580.000 DFU+Mode0.90057.000R DFU%2bMode57.000R
RSMRSTL_R0.720––
RTN_A_CPUCORE0.001––
SAVE_BAT_G0.757––
SAVE_BAT_S1.393––
SD3_RCOMP0.169––
SE_CTLR_FW_DWLD0.460––
SE_DEV_WAKE0.452––
SE_GPIO2_AO0.755––
SE_GPIO3_AO0.750––
SE_HOST_WAKE0.470––
SE_HOST_WAKE_R0.470––
SE_PWR_EN0.745––
SE_RX_N0.500––
SE_RX_P0.500––
SE_XTAL10.540––
SENSOR_PWR_EN0.553––
SEP_CAM_DISABLE_OE_L0.737––
SEP_CAM_DISABLE_OUT_L0.629––
SEP_DMIC_DISABLE_OUT_L0.674––
SMBUS_3V3_BATT_SCL0.6583.300–
SMBUS_3V3_BATT_SDA0.6613.300–
SMBUS_PCH_DATA0.794––
SMC_3V3G3HMAIN_ISENSE0.800––
SMC_5VG3S_ISENSE0.800––
SMC_CPU_HS_ISENSE0.805––
SMC_DCIN_VSENSE0.803––
SMC_DEBUGPRT_RX0.4581.800–
SMC_DEBUGPRT_TX0.4571.800–
SMC_DPWROK1V80.447––
SMC_FAN_0_PWM0.458––
SMC_FAN_0_TACH0.478––
SMC_KBD_BKLT_PWM0.520––
SMC_LID_LEFT0.695––
SMC_LID_RIGHT0.658––
SMC_PCH_PWROK0.449––
SMC_PCH_SYS_PWROK0.469––
SMC_PECI_RX0.436––
SMC_PECI_TX0.451––
SMC_PECI_TX_R0.466––
SMC_PROCHOT_L0.443––
SMC_RSMRST_L0.451––
SMC_SSD0_ISENSE0.810––
SMC_SYSRST_L0.451––
SOC_CLKREQ_L0.549––
SOC_COLD_RESET_L0.480––
SOC_DDR0_ZQ–1.100–
SOC_DFU_STATUS0.458––
SOC_DOCK_CONNECT0.459––
SOC_FORCE_DFU0.458––
SOC_HOLD_RESET0.458––
SOC_JTAG_SEL0.474––
SOC_KBD_BKLT_PWM0.450––
SOC_KBD_BKLT_PWM_R0.460––
SOC_PERST_L0.452––
SOC_SOCHOT_L0.459––
SOC_TESTMODE0.454––
SOC_USB_VBUS0.388––
SPARE_UPC_T_DBG1_R0.700––
SPARE_UPC_T_DBG2_R0.700––
SPARE_UPC_T_DBG3_R0.700––
SPARE_UPC_T_USB3_RN0.730––
SPARE_UPC_T_USB3_RP0.730––
SPARE_UPC_X_USB2_RN0.720––
SPARE_UPC_X_USB2_RP0.720––
SPARE_UPC_X_USB3_RN0.720––
SPARE_UPC_X_USB3_RP0.720––
SPI_MESA_CLK0.471––
SPI_MESA_MISO0.454––
SPI_SOCROM_CLK0.488––
SPI_SOCROM_CS_L0.475––
SPI_SOCROM_MISO0.460––
SPI_SOCROM_MOSI0.478––
SPI_SOCROM_MUX_MISO_R0.474––
SPI_SOCROM_WP_L0.545––
SPI_TBT_T_CLK0.550––
SPI_TBT_T_MISO0.570––
SPI_TBT_T_MOSI0.570––
SPI_TBT_X_CLK0.550––
SPI_TBT_X_CS_L0.560––
SPI_TBT_X_MISO0.560––
SPI_TBT_X_MOSI0.570––
SPI_TPAD_3V3_CLK0.556––
SPI_TPAD_3V3_CLK_R0.528––
SPI_TPAD_3V3_CS_L0.618––
SPI_TPAD_3V3_MISO0.623––
SPI_TPAD_3V3_MOSI0.578––
SPI_TPAD_3V3_MOSI_R0.590––
SPI_TPAD_CS_L0.460––
SPI_TPAD_MISO0.470––
SPI_TPAD_MISO_R0.490––
SPKR_ID00.459––
SPKR_ID10.460––
SPKRAMP_INT_L0.386––
SPKRAMP_L_AREG0.580––
SPKRAMP_L_BSTN0.772––
SPKRAMP_L_DREG0.532––
SPKRAMP_L_MODE0.000––
SPKRAMP_L_OUTN0.488––
SPKRAMP_L_OUTP0.489––
SPKRAMP_L_SNSN0.488––
SPKRAMP_RESET_L0.386––
SPKRCONN_L_OUTN0.488––
SPKRCONN_L_OUTP0.489––
SPMI_CLK0.469––
SPMI_DATA0.427––
SSD_BFH0.432––
SSD_PMU_RESET_L0.5731.800–
SSD0_CLK24M0.431––
SSD0_CLKREQ0_L0.441––
SSD0_CLKREQ1_L0.444––
SSD0_LPB_L0.451––
SSD0_PCIE_RESET_L0.428––
SSD0_RESET_L0.452––
SSD0_S4E_BOOT20.451––
SSD0_S4E_JTAG_SEL0.452––
SSD0_S4E_JTAG_TRST_L0.452––
SSD0_S4E0_ANI0_VREF0.630––
SSD0_S4E0_ANI1_VREF0.625––
SSD0_S4E0_DROOP_L0.492––
SSD0_S4E0_JTAG_TDO0.456––
SSD0_S4E0_PCIE_RESREF0.762––
SSD0_S4E0_SWD_UID00.472––
SSD0_S4E0_SWD_UID10.473––
SSD0_S4E0_UART_RX0.471––
SSD0_S4E0_ZQ_C0.084––
SSD0_S4E0_ZQ_L0.253––
SSD0_S4E1_ANI0_VREF0.631––
SSD0_S4E1_ANI1_VREF0.631––
SSD0_S4E1_DROOP_L0.500––
SSD0_S4E1_PCIE_RESREF0.762––
SSD0_S4E1_SWD_UID00.483––
SSD0_S4E1_SWD_UID10.484––
SSD0_S4E1_UART_RX0.481––
SSD0_S4E1_ZQ_C0.084––
SSD0_S4E1_ZQ_L0.253––
SSD0_SWCLK_UART_R2D0.433––
SSD0_SWDIO_UART_D2R0.430––
SSD0_WP_L0.366––
SWD_SOC_SWCLK0.456––
SWD_SOC_SWCLK_R0.476––
SWD_SOC_SWDIO0.456––
SWD_SOC_SWDIO_R0.476––
SYS_DETECTOL––
SYS_DETECT_L0.568––
SYS_STATE_BLUE_ROL––
SYS_STATE_GREEN_ROL––
SYS_STATE_RED_ROL––
TBT_POC_RESET0.611––
TBT_PWR_EN0.751––
TBT_T_FORCE_PWR0.600––
TBT_T_RBIAS0.780––
TBT_T_RSENSE0.000––
TBT_T_S0_PWR_EN0.540––
TBT_T_THERM_D_N0.000––
TBT_T_THERM_D_P0.843––
TBT_X_FORCE_PWR0.035––
TBT_X_RBIAS0.776––
TBT_X_RSENSE0.000––
TBT_X_S0_PWR_EN0.543––
TBT_X_THERM_D_N0.000––
TBT_XT_FLASH_BUSY_L0.527––
TBT_XT_PERST_L0.541––
TBT_XT_ROM_HOLD_L0.700––
TBT_XT_ROM_WP_L0.670––
TBT_XT_SPI_CLK0.526––
TBT_XT_SPI_CLK_DBG0.650––
TBT_XT_SPI_CS_L0.541––
TBT_XT_SPI_MISO0.538––
TBT_XT_SPI_MOSI0.543––
THMSNS_ADDR0.621––
THMSNS_CHGR_D6_N0.000––
THMSNS_CHGR_D6_P0.621––
THMSNS_CPU_D1_N0.000––
THMSNS_CPU_D1_P0.620––
THMSNS_DN0.000––
THMSNS_DRAM_D2_N0.000––
THMSNS_DRAM_D2_P0.620––
THMSNS_NAND_D5_N0.000––
THMSNS_NAND_D5_P0.622––
THMSNS_PMIC_D4_N0.000––
THMSNS_PMIC_D4_P0.622––
THMSNS_SOC_D3_N0.000––
THMSNS_SOC_D3_P0.622––
THMSNS_WLAN_D7_N0.000––
THMSNS_WLAN_D7_P0.621––
TP_BT_GPIO_40.514––
TP_BT_GPIO_50.515––
TP_CPU_PWRGD0.343––
TP_JTAG_SOC_TDI0.458––
TP_JTAG_SOC_TDO0.460––
TP_JTAG_SOC_TRST_L0.470––
TP_SMC_FIXTURE_MODE_L0.459––
TP_SOC_DEBUGPRT_RX0.458––
TP_SOC_DEBUGPRT_TX0.458––
TP_SOC_TST_CLKOUT0.458––
TP_SSD0_S4E0_JTAG_TDI0.480––
TP_SSD0_S4E1_JTAG_TDO0.488––
TP_USBC_PP20V_TOL––
TP_USBC_PP20V_XOL––
TP_WLAN_JTAG_SEL0.514––
TP_WLAN_JTAG_TCK0.515––
TP_WLAN_JTAG_TRST_L0.516––
TP_XDP_PCH_TCK0.310––
TPAD_KBD_WAKE_L0.457––
TPAD_SPI_3V3_EN0.628––
TPAD_SPI_3V3_INT_L0.868––
TPAD_SPI_EN0.458––
TPAD_SPI_INT_L0.477––
U8020_B_IN0.520––
UART_BT_LH_D2R0.513––
UART_BT_LH_R2D0.514––
UART_SE_D2R0.470––
UART_SE_D2R_CTS_L0.470––
UART_SE_R2D0.450––
UART_SE_R2D_RTS_L0.450––
UNUSED_BKLT_EN0.547––
UNUSED_LP8548_PWM0.537––
UPC_I2C_INT_L0.457––
UPC_PMU_RESET0.599––
UPC_T_FORCE_PWR0.600––
UPC_T_GPIO50.683––
UPC_T_R_OSC0.470––
UPC_T_RESET0.578––
UPC_T_SS0.580––
UPC_T_SWD_CLK0.600––
UPC_T_SWD_DATA0.706––
UPC_T_VRET0.000––
UPC_X_FORCE_PWR0.035––
UPC_X_R_OSC0.470––
UPC_X_RESET0.575––
UPC_X_SPI_CLK0.560––
UPC_X_SPI_CS_L0.570––
UPC_X_SPI_MISO0.580––
UPC_X_SPI_MOSI0.582––
UPC_X_SS0.578––
UPC_X_SWD_CLK0.690––
UPC_X_SWD_DATA0.500––
UPC_X_UART_RX0.550––
UPC_X_UART_TX0.550––
UPC_X_VRET0.000––
UPC_XT_5V_EN0.625––
USB_SOC_N0.698––
USB_SOC_P0.698––
USB_UPC_T1_N0.520––
USB_UPC_T1_P0.520––
USB_UPC_X1_N0.520––
USB_UPC_X1_P0.520––
USB2_FCT_N0.465––
USB2_FCT_P0.468––
USB2_TBT_T_N0.520––
USB2_TBT_T_P0.520––
USB2_TBT_X_N0.520––
USB2_TBT_X_P0.520––
USB3_BSSB_D2R_N0.339––
USB3_BSSB_D2R_P0.338––
USB3_BSSB_D2R_R_N0.341––
USB3_BSSB_D2R_R_P0.339––
USB3_BSSB_R2D_C_N0.328––
USB3_BSSB_R2D_C_P0.330––
USB3_BSSB_R2D_N0.687––
USB3_BSSB_R2D_P0.689––
USB3_FCT_D2R_N0.333––
USB3_FCT_D2R_P0.331––
USB3_FCT_R2D_C_N0.325––
USB3_FCT_R2D_C_P0.327––
USBC_HST_AUXCH_C_N0.005––
USBC_HST_AUXCH_C_P0.381––
USBC_HSX_AUXCH_C_N0.378––
USBC_HSX_AUXCH_C_P0.377––
USBC_T_CC10.576––
USBC_T_CC20.575––
USBC_T_D2R_CR_N<1>OL––
USBC_T_D2R_CR_N<2>OL––
USBC_T_D2R_CR_P<1>OL––
USBC_T_D2R_CR_P<2>OL––
USBC_T_R2D_N<1>OL––
USBC_T_R2D_N<2>OL––
USBC_T_R2D_P<1>OL––
USBC_T_R2D_P<2>OL––
USBC_T_RESET_L0.670––
USBC_T_RST_L0.672––
USBC_T_SBU10.642––
USBC_T_SBU20.641––
USBC_T_USB_BOT_N0.760––
USBC_T_USB_BOT_P0.760––
USBC_T_USB_TOP_N0.760––
USBC_T_USB_TOP_P0.760––
USBC_X_CC10.573––
USBC_X_CC20.572––
USBC_X_D2R_CR_N<1>OL––
USBC_X_D2R_CR_N<2>OL––
USBC_X_D2R_CR_P<1>OL––
USBC_X_D2R_CR_P<2>OL––
USBC_X_R2D_N<1>OL––
USBC_X_R2D_N<2>OL––
USBC_X_R2D_P<1>OL––
USBC_X_R2D_P<2>OL––
USBC_X_RESET_L0.674––
USBC_X_SBU10.640––
USBC_X_SBU20.640––
USBC_X_USB_BOT_N0.750––
USBC_X_USB_BOT_P0.750––
USBC_X_USB_TOP_N0.750––
USBC_X_USB_TOP_P0.750––
UVP_DIS_L0.551––
VCCINAUX_AGND0.000––
VCCINAUX_BOOT_RC0.375––
VCCINAUX_DRVH0.830––
VCCINAUX_DRVH_R0.830––
VCCINAUX_DRVL0.566––
VCCINAUX_DRVL_R0.566––
VCCINAUX_DRVL_R20.566––
VCCINAUX_EN_R0.429––
VCCINAUX_FB0.760––
VCCINAUX_ISNS_N0.1221.800143.000
VCCINAUX_ISNS_P0.1221.800143.000
VCCINAUX_OCSET0.608––
VCCINAUX_PGOOD0.626––
VCCINAUX_PROG0.756––
VCCINAUX_PROG1OL––
VCCINAUX_PROG2OL––
VCCINAUX_R0.1221.800143.000
VCCINAUX_RTN0.001––
VCCINAUX_SET00.780––
VCCINAUX_SET10.767––
VCCINAUX_SET1_ROL––
VCCINAUX_SREF0.780––
VCCINAUX_SW0.1221.800143.000R
VCCINAUX_VBST0.375––
VCCINAUX_VO0.605––
VCCINAUXVSENSE_IN0.216––
VCCST_EN_B0.569––
VCCST_EN_C0.570––
VCCST_OVERRIDE0.379––
VCCST_OVERRIDE_3V30.642––
VCCST_PWRGD0.604––
VCCST_PWRGD_R0.616––
VDDA_SN100V0.340––
VDDC_SN100V0.340––
VDDNV_SN100V0.366––
VDDPLL_SN100V0.370––
VHV_SN100V0.320––
VREF_SN100V0.690––
WLAN_JTAG_TDI0.515––
WLAN_JTAG_TDO0.516––
WLAN_PWR_EN0.737––
WLAN_SROM_CLK0.514––
WLAN_SROM_CS0.547––
WLAN_SROM_CS_R0.590––
WLAN_SROM_DIN0.546––
WLAN_SROM_DOUT0.516––
WLAN_SROM_ORGOL––
WLAN_THROTTLE0.444––
WLANBT_HOST_WAKE0.448––
XDP_CPUPCH_TCK0.043––
XDP_CPUPCH_TDI0.269––
XDP_CPUPCH_TDO0.213––
XDP_CPUPCH_TMS0.268––
XDP_CPUPCH_TRST_L0.284––
XDP_LSX_TBTA_P2R0.692––
XDP_LSX_TBTA_R2P0.680––
XDP_LSX_TBTB_P2R0.690––
XDP_LSX_TBTB_R2P0.680––
XDP_MEM_OK0.801––
XDP_PCH_I2C_UPC_SCL0.542––
XDP_PCH_I2C_UPC_SDA0.540––
XDP_PCH_OBSDATA_B20.818––
XDP_PCH_STRP_CNV_DISABLE0.804––
XDP_PCH_STRP_SPIROM_SAF0.790––
XDP_PRESET_L0.558––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01958?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01958: diode 0.410, voltage 13.050. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-01958?

OpenBoardData's known-good values for PP3V3_G3H on the 820-01958: diode 0.363, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01958?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01958: diode 0.347. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01958 board?

Open your own 820-01958 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License