Apple laptop board · OpenBoardData

820-2915 known-good readings

Known-good readings for the Apple laptop board 820-2915: 105 nets, including 19 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 19 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-2915.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 19 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 4

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H–3.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, as its name indicates (G3H = always on). The archive lists a known-good voltage of 3.400 V; no known-good diode or resistance reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far below 3.400 V usually points to a load pulling the rail down or a fault in its source, but confirm with the diode reading before suspecting a part.

PPBUS_G3H–12.500–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on the 820-2915; the "G3H" suffix, from the name, marks it as an always-on rail. The only known-good figure here is 12.500 V, with no condition recorded, and there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from PPBUS_G3H to ground, then power the board and measure the voltage. A voltage far from 12.500 V usually points to a fault on the bus or its source rather than to the load, but that is a general guide, not a confirmed cause.

PPDCIN_G3H_CHGR–18.250–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in the name indicates it is always-on, present whenever the charger is connected. The archive lists one known-good voltage of 18.250 V, with no condition recorded, and no known-good diode or resistance reading for this net. Check it with the board unpowered in diode mode from the rail to ground, then apply the charger and measure the voltage on the rail. A voltage far below 18.250 V points to a charger or input-path problem rather than a fault on the rail itself, but that is a likely cause, not a confirmed one.

PPVBAT_G3H_CHGR_REG–12.500–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side regulated rail derived from the battery/main power input; the G3H in the name indicates an always-on rail, and CHGR indicates it belongs to the charger circuit. The only known-good reading recorded here is 12.500 V; no diode or resistance value is listed for this rail. Check it unpowered in diode mode to ground first, then measure the voltage with power applied and compare against 12.500 V. A voltage far from that, or a near-short in diode mode, usually points to a fault on the rail or its load rather than proving a specific part bad.

S5 and SUS: standby 3

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PPVIN_S5_HS_COMPUTING_ISNS0.4312.500–
AI: what PPVIN_S5_HS_COMPUTING_ISNS is and how to check it

PPVIN_S5_HS_COMPUTING_ISNS (820-2915) — reference note

  • From the name, this is a high-side (HS) current-sense (ISNS) input for the computing rail, in the S5 standby domain.
  • Known-good readings from the archive: diode 0.43 to ground, voltage 12.500. These are community readings and a guide only; no condition is recorded.
  • To check: power off and unplug, then diode mode from the net to ground. Then power up and measure the voltage on the net.
  • A diode reading well below 0.43 suggests a short or leaky part on that net; a voltage far from 12.500 points at the input supply or the sense path, not necessarily a bad part. No known-good resistance reading here.
PPVIN_S5_HS_GPU_ISNS0.4412.500–
AI: what PPVIN_S5_HS_GPU_ISNS is and how to check it

PPVIN_S5_HS_GPU_ISNS (820-2915) — reference note

  • From the name, this is a high-side current-sense (ISNS) input rail tied to the GPU supply, in the S5/SUS standby stage. The name suggests it carries the main adapter input voltage rather than a regulated low rail.
  • Known-good readings in the archive: diode 0.44 to ground, and 12.500 V with power applied. These are community values and only a guide; no known-good resistance reading here.
  • To check it: power off and unplug, then measure diode mode from the net to ground and compare with 0.44. Then power up and measure the voltage, expecting about 12.5 V.
  • A diode reading far below 0.44 suggests a short or leaky part on the rail; a voltage well off 12.5 V points upstream to the input/adapter path rather than the GPU side. Confirm with a second reading before replacing anything.
PPVIN_S5_HS_OTHER_ISNS–12.500–
AI: what PPVIN_S5_HS_OTHER_ISNS is and how to check it

PPVIN_S5_HS_OTHER_ISNS — reference note

  • What it is: From the name, a high-side (HS) input rail in the S5 standby domain, with an "ISNS" current-sense function. The exact parts on it aren't documented here.
  • Known-good reading: 12.500 V, from the readings archive (no condition recorded). No known-good diode or resistance reading here.
  • How to check: With the board unpowered, diode mode from the rail to ground; then power up and measure the voltage, expecting about 12.5 V.
  • If it's far off: A very low diode reading suggests a short or leaky part on the rail; a missing or low voltage points to the supply feeding it or an enable/current-sense fault upstream. Confirm with a second measurement before replacing anything.

S3: memory 1

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V5_S3_CPU_VCCDQ––144.00R
AI: what PP1V5_S3_CPU_VCCDQ is and how to check it
  • What it is: From the name, PP1V5_S3_CPU_VCCDQ is a 1.5 V rail in the S3 (memory) startup stage, likely feeding the CPU's DDR memory interface. This is inferred from the rail name only; no board file is available to confirm which parts sit on it.
  • Known-good reading: The archive lists 144.00R resistance for this net. No known-good diode or voltage reading is recorded here.
  • How to check: With the board unpowered, measure diode mode to ground on PP1V5_S3_CPU_VCCDQ, then measure its voltage with power applied and the board in S3.
  • If it's far off: A very low resistance or diode reading to ground suggests a short on the rail, but one reading alone doesn't confirm a bad part. Compare against a known-good board or a matching rail before replacing anything.

S0: running 11

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V0_S0GPU––293.00R
AI: what PP1V0_S0GPU is and how to check it

PP1V0_S0GPU is a 1.0 V rail for the GPU, and the S0 in its name indicates it belongs to the running (S0) power state rather than standby. The only known-good reading in the archive is 293.00R resistance; there is no known-good diode or voltage value recorded here. Check it with the board unpowered in resistance or diode mode from the rail to ground, then confirm the voltage with power applied. A resistance far below 293.00R usually points to a short or a failing load on the rail, while a much higher or open reading points to a missing supply or a broken connection; treat the 293.00R figure as a guide only.

PP1V0_S0GPU_ISNS––293.00R
AI: what PP1V0_S0GPU_ISNS is and how to check it

PP1V0_S0GPU_ISNS (820-2915) — reference note

  • What it is: from the name, a 1.0 V rail in the S0 (running) state, tied to the GPU, with "ISNS" indicating a current-sense line rather than a plain supply. The exact parts on it aren't documented here.
  • Known-good reading: 293.00R to ground in resistance mode, from the community archive. That is a guide only and varies with board state; no known-good diode or voltage reading exists here.
  • How to check: power off and unplug, then measure resistance or diode to ground and compare with 293.00R. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower resistance or a short suggests a fault on the sensed side or a shorted component; a much higher one suggests an open trace or missing part. Confirm with a second measurement before replacing anything.
PP1V05_S0_CPU_VCCPQE––19.00R
AI: what PP1V05_S0_CPU_VCCPQE is and how to check it

PP1V05_S0_CPU_VCCPQE is a 1.05 V rail feeding the CPU's VCCPQE domain; the "S0" part of the name indicates it is active in the running state. The only archived reading is 19.00R resistance, with no stated condition, and there is no known-good diode or voltage reading here. Check it unpowered in diode mode to ground, then measure the voltage with the board powered in S0. A resistance far below 19R usually points to a short or a failing load on the rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything.

PP1V5_S0GPU_ISNS––30.00R
AI: what PP1V5_S0GPU_ISNS is and how to check it
  • What it is: From the name, PP1V5_S0GPU_ISNS is a 1.5 V S0 (running-state) GPU rail sense line on the 820-2915. The ISNS suffix usually means a current-sense node rather than the rail feed itself, so it may sit across a shunt or sense resistor (general interpretation, not from board data).
  • Known-good reading: The archive lists 30.00R resistance for this net. No known-good diode or voltage reading is recorded here.
  • How to check: With the board unpowered, measure resistance and diode drop from the net to ground and compare with 30.00R. Then power up and measure the voltage on the net; no known-good voltage is available for comparison.
  • If it's far off: A much lower resistance or short to ground points to a fault on the sense path or its load, but one reading isn't proof — trace the sense resistor and compare against a known-good board before replacing anything.
PP1V8_S0GPU_ISNS––572.00R
AI: what PP1V8_S0GPU_ISNS is and how to check it

PP1V8_S0GPU_ISNS is a 1.8 V rail tied to the GPU, judging by its name; the S0 suffix indicates it belongs to the running (S0) state. The only known-good figure here is a resistance of 572.00R, with no condition recorded. With the board unpowered, measure resistance from the rail to ground and compare with that figure; then power up and check the voltage, though no known-good voltage reading exists here. A resistance far below 572R usually points to a short or a failing load on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S00.305––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judged from the rail name. The archive lists one known-good diode reading of 0.305 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.305 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0_CPUTHMSNS_R0.347––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R is a 3.3 V rail; from the name it's an S0 (running-state) supply tied to CPU thermal sensing. The archive's only known-good reading is a diode value of 0.347 to ground, with no stated condition; there is no known-good voltage reading here.

  • Check it unpowered: diode mode from the rail to ground, red probe on ground. Compare with 0.347 as a guide.
  • Then power the board and measure the voltage at the rail; expect about 3.3 V, though that figure comes from the rail's name, not the data.
  • A diode reading far below 0.347 suggests a short or a leaky part on the rail; far above suggests an open path. Either way, confirm with a second measurement before replacing anything.
PP3V3_S0GPU––173.00k
AI: what PP3V3_S0GPU is and how to check it
  • What it is: PP3V3_S0GPU is a 3.3 V rail; the "S0" part of the name indicates it belongs to the running (S0) power state, and "GPU" suggests it supplies the graphics section. This is from the name only.
  • Known-good reading: the archive lists 173.00k resistance for this net. No known-good diode or voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S0GPU to ground, then apply power and measure the voltage on the rail.
  • If far off: a large deviation from 173.00k usually points to a short or a faulty component on that rail, but one reading isn't proof; compare with a known-good board before replacing anything.
PPVCCSA_S0_REG––24.00R
AI: what PPVCCSA_S0_REG is and how to check it

PPVCCSA_S0_REG is a running-state (S0, from the name) supply rail; the "VCCSA" part suggests it feeds the system agent section of the CPU, though that's general naming, not board data. The only known-good reading here is 24.00R resistance, with no condition or diode/voltage value recorded. Check it unpowered in diode mode to ground first, then measure its voltage with the board powered in S0. A reading far from 24.00R usually points to a short or open on the rail or its load, but one reading alone doesn't confirm a bad part. No known-good diode or voltage reading exists for this rail, so compare against a matching rail or a known-good board.

PPVCORE_S0_AXG0.04–7.40R
AI: what PPVCORE_S0_AXG is and how to check it

PPVCORE_S0_AXG is the CPU core power rail, active in the S0 (running) state, as the name indicates. Known-good readings from the archive are diode 0.04 and resistance 7.40R; no known-good voltage reading is recorded here. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode or resistance far from those values usually points to a short or a damaged component on the rail, but the archive gives no voltage reference, so compare against a known-good board.

PPVCORE_S0_CPU––4.40R
AI: what PPVCORE_S0_CPU is and how to check it

PPVCORE_S0_CPU is the CPU core power rail; the "S0" in the name indicates it is active in the running state. The only known-good reading here is 4.40R resistance, with no condition recorded, and there is no known-good diode or voltage value in this data. Check it with the board unpowered in resistance or diode mode from the rail to ground, then measure the voltage with power applied. A reading far from 4.40R usually points to a short or a failed component on the rail, but a single reading isn't proof, so compare against a known-good board before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
(NC)0.734––
AUD_CONNJ1_RING0.700––
AUD_CONNJ1_SLEEVE0.000––
AUD_CONNJ1_SLEEVE20.107––
AUD_CONNJ1_SLEEVEDETOL––
AUD_CONNJ1_TIP0.695––
AUD_CONNJ1_TIPDET0.699––
AUD_SPDIF_OUT0.666––
CPU_THERMD_N0.734––
CPU_THERMD_P0.739––
CPUTHMSNS_ALERT_L0.746––
CPUTHMSNS_D2_N0.755––
CPUTHMSNS_D2_P0.754––
CPUTHMSNS_THM_L0.752––
CPUVCCIOS0_LL0.00––
GND0.00––
GPUTHMSNS_D_N0.756––
P1V5FB_LL0.04––
P3V42G3H_SW–3.400–
PEG_D2R_C_N<0>0.42––
PEG_D2R_C_N<1>0.42––
PEG_D2R_C_N<2>0.43––
PEG_D2R_C_N<3>0.42––
PEG_D2R_C_N<4>0.42––
PEG_D2R_C_N<5>0.43––
PEG_D2R_C_N<6>0.42––
PEG_D2R_C_N<7>0.43––
PEG_D2R_C_P<0>0.42––
PEG_D2R_C_P<1>0.42––
PEG_D2R_C_P<2>0.43––
PEG_D2R_C_P<3>0.42––
PEG_D2R_C_P<4>0.42––
PEG_D2R_C_P<5>0.42––
PEG_D2R_C_P<6>0.42––
PEG_D2R_C_P<7>0.43––
PEG_D2R_N<0>0.36––
PEG_D2R_N<1>0.36––
PEG_D2R_N<2>0.37––
PEG_D2R_N<3>0.36––
PEG_D2R_N<4>0.36––
PEG_D2R_N<5>0.36––
PEG_D2R_N<6>0.35––
PEG_D2R_N<7>0.38––
PEG_D2R_P<0>0.35––
PEG_D2R_P<1>0.36––
PEG_D2R_P<2>0.36––
PEG_D2R_P<3>0.36––
PEG_D2R_P<4>0.35––
PEG_D2R_P<5>0.36––
PEG_D2R_P<6>0.35––
PEG_D2R_P<7>0.37––
PEG_R2D_C_N<0>0.37––
PEG_R2D_C_N<1>0.34––
PEG_R2D_C_N<2>0.34––
PEG_R2D_C_N<3>0.34––
PEG_R2D_C_N<4>0.34––
PEG_R2D_C_N<5>0.34––
PEG_R2D_C_N<6>0.36––
PEG_R2D_C_N<7>0.36––
PEG_R2D_C_P<0>0.34––
PEG_R2D_C_P<1>0.34––
PEG_R2D_C_P<2>0.35––
PEG_R2D_C_P<3>0.78––
PEG_R2D_C_P<4>0.35––
PEG_R2D_C_P<5>0.34––
PEG_R2D_C_P<6>0.38––
PEG_R2D_C_P<7>0.36––
PEG_R2D_N<0>0.78––
PEG_R2D_N<1>0.77––
PEG_R2D_N<2>0.78––
PEG_R2D_N<4>0.78––
PEG_R2D_N<5>0.78––
PEG_R2D_N<6>0.78––
PEG_R2D_N<7>0.78––
PEG_R2D_P<0>0.78––
PEG_R2D_P<1>0.77––
PEG_R2D_P<2>0.78––
PEG_R2D_P<4>0.78––
PEG_R2D_P<5>0.78––
PEG_R2D_P<6>0.78––
PEG_R2D_P<7>0.78––
PP1V0_S0GPU––293.00R
PP1V0_S0GPU_ISNS––293.00R
PP1V5_GPU_REG0.03–30.00R
PP1V05_S0_CPU_VCCPQE––19.00R
PP1V5_S0GPU_ISNS––30.00R
PP1V5_S3_CPU_VCCDQ––144.00R
PP1V8_GPUIFPX––568.00R
PP1V8_S0GPU_ISNS––572.00R
PP3V3_S00.305––
PP3V3_S0_CPUTHMSNS_R0.347––
PP3V3_S0GPU––173.00k
PP3V42_G3H–3.400–
PPBUS_G3H–12.500–
PPDCIN_G3H_CHGR–18.250–
PPVBAT_G3H_CHGR_REG–12.500–
PPVCCSA_S0_REG––24.00R
PPVCORE_GPU––7.70R
PPVCORE_S0_AXG0.04–7.40R
PPVCORE_S0_CPU––4.40R
PPVIN_S5_HS_COMPUTING_ISNS0.4312.500–
PPVIN_S5_HS_GPU_ISNS0.4412.500–
PPVIN_S5_HS_OTHER_ISNS–12.500–
SMBUS_SMC_B_S0_SCL0.514––
SMBUS_SMC_B_S0_SDA0.514––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-2915?

OpenBoardData's known-good values for PPBUS_G3H on the 820-2915: voltage 12.500. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-2915?

OpenBoardData's known-good values for PP3V42_G3H on the 820-2915: voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S0 read on the 820-2915?

OpenBoardData's known-good values for PP3V3_S0 on the 820-2915: diode 0.305. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-2915 board?

Open your own 820-2915 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License