Apple laptop board · OpenBoardData

820-00928 known-good readings

Known-good readings for the Apple laptop board 820-00928: 2,133 nets, including 113 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 113 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00928.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 113 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 12

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V0_G3H0.447––
AI: what PP3V0_G3H is and how to check it

PP3V0_G3H is a 3.0 V always-on rail; the G3H part of the name indicates it stays up whenever the board has power, before the S5/S4/S3/S0 stages. The only known-good reading here is a diode value of 0.447 to ground, with no condition recorded. To check it, power off and measure diode mode from PP3V0_G3H to ground, then power up and confirm about 3.0 V. No known-good voltage reading is recorded here, so compare against a matching always-on rail or a known-good board. A diode reading far from 0.447 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PP3V3_G3H0.343.300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H (820-00928) — reference note

  • What it is: the 3.3 V always-on rail. The "G3H" suffix comes from the rail name and marks it as a G3H (always-on) supply, present as soon as the logic board has valid input power, before the S5/S4/S3/S0 stages.
  • Known-good readings (community guide): diode 0.34 to ground, and 3.300 V with power applied. The startup sequence also lists 3V3 on PP3V3_G3H at L6900 pin 1.
  • How to check: with the board unpowered, measure diode mode from PP3V3_G3H to ground; then apply power and measure the voltage. No known-good resistance reading here.
  • If it's off: a voltage well below 3.3 V points upstream, at the G3H regulator's enable and input (PM_EN_P3V3_G3H and PPDCIN_G3H in the startup notes) rather than at the rail itself. A diode reading far from 0.34 suggests a short or leaky load on the rail; confirm with a second point before condemning anything.
PP3V3_G3H_REG_R0.3603.300–
AI: what PP3V3_G3H_REG_R is and how to check it

PP3V3_G3H_REG_R — the name marks it as a 3.3 V G3H rail: the always-on 3.3 V supply that comes up early in startup, before the S5/S4/S3/S0 stages. The "_REG_R" suffix suggests a regulator output side, but that's from the name only.

  • Known-good readings (community guide): diode 0.360 to ground, voltage 3.300 V. No condition is recorded for these.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage. The startup sequence lists 3V3 on PP3V3_G3H at L6900 pin 1 as the point where this rail appears.
  • If it's far off: a low diode reading or missing voltage points to a short or a dead regulator feeding it, but confirm with a second measurement before replacing anything. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PPBUS_G3H0.36013.100–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail, and the G3H suffix (from the name) marks it as an always-on rail once the charger has switched over. Known-good readings here are diode 0.360 and voltage 13.100; treat these as a community guide, not a factory spec. Check it unpowered in diode mode from PPBUS_G3H to ground, then power the board and measure the voltage. A diode reading far below 0.360 suggests a short or leaky load on the rail, while a voltage well off 13.100 with a normal diode reading points back at the charger side (U7000 and the Q7030/Q7040 switchover). No known-good resistance reading is listed for this rail.

PPBUS_G3H_R0.373––
AI: what PPBUS_G3H_R is and how to check it
  • What it is: PPBUS_G3H_R is the main G3H bus rail; the "G3H" part of the name means it's an always-on rail, present from the earliest power stage. The "_R" suffix is just a net-name variant.
  • Known-good reading: diode-to-ground 0.373 (community archive, guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage on it.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage points back to the upstream supply (U7000 and the Q7030/Q7040 pass FETs, per the startup notes). Confirm with a second reading before replacing anything.
PPDCIN_G3H0.5520,000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main DC input rail that feeds the G3H (always-on) domain, judged from the "G3H" in its name; it's what the USB-C input switching passes on to the rest of the board.

  • Known-good readings (community guide): diode 0.55 to ground, and 20,000 (i.e. 20V) with a charger connected. The startup notes show 5V here before the CD3215 negotiates, then 20V after switch-over at Q3100.
  • To check: power off and unplug, then diode-mode from PPDCIN_G3H to ground. Then apply power and measure the voltage, first at 5V and again after the 20V handshake.
  • A diode reading far from 0.55 suggests a short or leaky part on the rail; a voltage stuck near 5V with no 20V points back at the CD3215/USB-C input path rather than this rail itself. No known-good resistance value is listed here.
PPDCIN_G3H_CHGR0.5520,000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR — the name says it is the charger-side DC input in the G3H (always-on) domain: the main DC-in rail feeding the charger circuit. Known-good readings in the archive: diode 0.55 to ground, and 20,000 (20 V) with the charger connected and the board switched over to 20 V.

  • Check it unpowered in diode mode, red probe on ground, black on the rail; compare with 0.55.
  • Then power up with a known charger and measure the voltage; it should reach about 20 V once the USB-C port has negotiated 20 V.
  • A diode reading far below 0.55 suggests a short or leaky part on the rail; far above suggests an open path. A voltage stuck near 5 V points to the 20 V switchover not completing, so check the port's CD3215 LDOs and gate signals first.
  • No known-good resistance reading is recorded here.
PPDCIN_G3H_CHGR_R0.560––
AI: what PPDCIN_G3H_CHGR_R is and how to check it

PPDCIN_G3H_CHGR_R — the name marks it as the charger-side input rail in the G3H (always-on) domain, i.e. the DC input that feeds the charger circuit before the main power path. This is from the name only; the parts on the net aren't listed in the data.

  • Known-good: diode-to-ground 0.560 (community reading, a guide only, no condition recorded). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure DC voltage on the rail.
  • A diode reading far below 0.560 usually points to a shorted or leaky part on that rail; far above suggests an open path. Confirm with a second reading before replacing anything.
PPVBAT_G3H_CHGR_R0.362––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is a G3H (always-on) rail tied to the charger/battery path, judged from its name; the archive doesn't list which parts sit on it. Known-good: diode 0.362 to ground (community reading, board state not stated); no known-good voltage reading here. Check it unpowered in diode mode to ground, then measure its voltage with power applied and compare against a matching charger/battery rail or a known-good board. A diode reading far from 0.362 usually points to a short or a damaged component on that net, but one reading isn't proof — confirm before replacing anything.

PPVBAT_G3H_CHGR_REG0.36013.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a charger-side battery rail; the G3H part of the name indicates it is always-on, and CHGR_REG marks it as a charger regulated output (from the name). Known-good readings in the archive: diode 0.360 to ground, and 13.100 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading well below 0.360 suggests a short or leaky load on the rail; a voltage far from 13.100 V points to the charger not regulating or the rail being loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PPVBAT_G3H_CONN0.62––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is a G3H (always-on) rail, judging from the name, and it appears to be the battery connector side of the always-on battery supply. The only known-good reading here is a diode value of 0.62; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered, with the battery and charger disconnected: diode mode from PPVBAT_G3H_CONN to ground, red probe on ground. Compare with 0.62 as a guide.
  • Then apply power and measure the voltage on the rail. No known-good voltage here, so compare against a matching battery-side net or a known-good board.
  • A diode reading far below 0.62 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. Confirm with a second measurement before replacing anything.
PPVIN_G3H_P3V3G3H0.55––
AI: what PPVIN_G3H_P3V3G3H is and how to check it
  • What it is: From the name, this is the always-on (G3H) input feed for the 3V3_G3H regulator — the rail that comes up early, before the S5/S4/S3/S0 stages.
  • Known-good reading: diode 0.55 to ground (community value, a guide only; it varies with board state). No known-good voltage is recorded here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage on it.
  • If it's far off: a low or shorted diode reading usually points to a shorted load or capacitor on that rail; an open/high reading points to a broken feed. Confirm with a second measurement before replacing anything.

S5 and SUS: standby 19

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_S5_PCH_DCPDSW0.331––
AI: what PP1V_S5_PCH_DCPDSW is and how to check it

PP1V_S5_PCH_DCPDSW is a 1 V S5 standby rail feeding the PCH's DCPDSW (display/panel power switch) domain; the S5 and PCH naming is from the rail name, and the exact parts on it aren't documented here. Known-good: diode 0.331 in diode mode to ground, with no voltage or resistance reading recorded for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on it in S5 standby. A diode reading far below 0.331 usually points to a short or leaky load on the rail; a far higher or open reading points to a broken connection. Confirm with the voltage before replacing anything, since one reading alone isn't proof of a bad part.

PP1V_SUS_PCH_VCCCLK5_F0.0401.000–
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it

PP1V_SUS_PCH_VCCCLK5_F — 1 V standby rail (reference note)

  • From the name: a 1 V rail (PP1V), in the SUS/standby domain, feeding the PCH's clock-related supply (VCCCLK5). It sits in the S5/SUS standby stage, so it should be present before the board fully powers on.
  • Known-good readings in the archive: diode 0.040 and voltage 1.000. These are community readings and only a guide; the archive gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode reading far from 0.040 usually points to a short or a leaky part on that rail; a voltage far from 1.000 with a normal diode reading points upstream at the regulator or its enable. No known-good resistance reading here, so compare against a matching rail or a known-good board.
PP1V_SUS_PCH_VCCHDAPLL_F0.0401.000–
AI: what PP1V_SUS_PCH_VCCHDAPLL_F is and how to check it

PP1V_SUS_PCH_VCCHDAPLL_F — reference note

  • From the name: a 1 V standby (SUS/S5) rail feeding the PCH's HD Audio PLL supply. It sits in the standby stage, so it should be present before the board fully powers on.
  • Known-good readings from the archive: diode 0.040 to ground, voltage 1.000 V. These are community figures and only a guide.
  • To check: power off and unplug, then diode mode from the rail to ground; power up and measure the voltage. A diode far from 0.040 suggests a short or leak on the rail; a missing or wrong voltage with a normal diode points upstream at the standby regulator feeding it.
  • No known-good resistance reading is recorded here, so compare against a matching standby rail or a known-good board.
PP1V_SUS_PCH_VCCUSB2HDAPLL_F0.0401.000–
AI: what PP1V_SUS_PCH_VCCUSB2HDAPLL_F is and how to check it

PP1V_SUS_PCH_VCCUSB2HDAPLL_F — reference note

  • From the name, this is a 1 V standby (SUS) rail feeding the PCH's USB2/HD audio PLL supply. It belongs to the S5/SUS standby stage, so it should be present before the board reaches S0.
  • Known-good readings in the archive: diode 0.040 and voltage 1.000 V. These are community values and a guide only; the data gives no condition for them.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage. A diode reading far below 0.040 suggests a short or leaky load on the rail; a voltage well off 1.000 V points to the rail's regulator or its enable, not the PCH itself.
  • No known-good resistance reading is recorded for this rail, so compare against a matching rail or a known-good board.
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.045––
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL_F is and how to check it

PP1V_SUSSW_PCH_VCCAMPHYPLL_F — from the name, a 1V switched standby rail feeding the PCH's amplifier/PLL supply. It belongs to the SUS (standby) stage, so it should come up early, before S5/S4/S3/S0 rails.

  • Known-good: diode-to-ground 0.045 (no condition recorded). No known-good voltage reading here.
  • Check: power off and unplugged, diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • A diode reading far below 0.045 suggests a short or leaky load on the rail; far above suggests an open path to its source. Confirm with a second point on the same net before condemning anything.
PP1V0_SUS0.0401.000–
AI: what PP1V0_SUS is and how to check it

PP1V0_SUS is a 1.0 V standby rail; the "SUS" in the name marks it as part of the suspend/standby group, active before the main rails come up. The archived readings for this rail are a diode value of 0.040 and 1.000 V, with no stated condition, so treat them as a guide only.

  • With the board unpowered, measure diode mode from PP1V0_SUS to ground and compare with 0.040.
  • Then apply power in the standby state and check for about 1.000 V.
  • A diode reading far below known-good usually suggests a short or a leaky part on the rail; a missing voltage points more to the rail's regulator or its enable. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP1V2_S5_SMC_VDDC0.517––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC is the 1.2 V SMC supply in the S5 standby stage, judged from its name (S5 = standby). The archive's known-good diode reading is 0.517, with no condition noted; the startup notes also list 1V2 on this rail at C5012 pin 1 once the SMC rails are up.

  • Check it unpowered: diode mode, red probe on ground, black on the rail (or the C5012 pad).
  • Then power the board and confirm about 1.2 V there.
  • No known-good voltage reading is recorded here, so treat 1V2 as the expected level from the name, not a measured value.

A diode reading far below 0.517 usually suggests a short or a leaky part on the rail; far above suggests an open path. Confirm with a second point on the same rail before suspecting any part.

PP1V8_SUS0.4301.800–
AI: what PP1V8_SUS is and how to check it

PP1V8_SUS is a 1.8 V standby rail; the "SUS" suffix and its S5/standby startup stage come from the rail name, so it should be present in standby before the board fully wakes. Known-good readings here are diode 0.430 and voltage 1.800. With the board unpowered, measure diode mode from PP1V8_SUS to ground and compare with 0.430; then power up and check for 1.800 V. A diode reading far below known-good usually points to a short or leaky load on the rail, while a missing voltage with a normal diode reading points more to the regulator or its enable. These are community readings and only a guide, so confirm on a known-good board before condemning a part.

PP1V8_SUS_REG_R0.427––
AI: what PP1V8_SUS_REG_R is and how to check it

PP1V8_SUS_REG_R is a 1.8 V standby rail; the "SUS" in the name places it in the S5/SUS standby stage, and "REG" suggests a regulated supply. The only known-good reading here is a diode value of 0.427 to ground, with no condition recorded; there is no known-good voltage or resistance value in this data.

  • With the board unpowered, measure diode mode from PP1V8_SUS_REG_R to ground and compare with 0.427. A far lower reading usually points to a short or a leaky part on the rail; a much higher one can mean an open path.
  • Then apply power and check the rail sits near 1.8 V when standby is present. A missing or low voltage with a normal diode reading points upstream to its regulator or enable, not to a short.
  • One reading alone doesn't condemn a part; compare against a matching rail or a known-good board before replacing anything.
PP3V0_S5_AVREF_SMC0.602––
AI: what PP3V0_S5_AVREF_SMC is and how to check it

PP3V0_S5_AVREF_SMC — from the name, a 3.0 V S5 (standby) analog reference rail feeding the SMC. It should be present once the SMC rails come up, before the board leaves standby.

  • Known-good: diode mode to ground 0.602 (community reading, a guide only). Voltage: about 3V0 at C5020 pin 1 in the startup sequence. No known-good resistance reading here.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 0.602. Then power up and measure DC volts at C5020 pin 1.
  • A diode reading far below 0.602 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything — one reading alone isn't proof.
PP3V3_S50.3703.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the S5 suffix comes from its name and places it in the S5/SUS standby stage, live before the board fully wakes. Known-good readings here are diode 0.370 and voltage 3.300, community-contributed and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far off 3.300 or a diode reading far from 0.370 points to a fault on that rail or its load, but one reading alone doesn't confirm a bad part. No known-good resistance reading here.

PP3V3_S5_POLARIS0.501––
AI: what PP3V3_S5_POLARIS is and how to check it

PP3V3_S5_POLARIS — 3.3 V standby rail (S5 stage, from the name).

  • Known-good: diode reading 0.501 to ground. No known-good voltage reading here.
  • Check unpowered: diode mode, red probe on ground, black on the rail; compare with 0.501.
  • Check powered: DC volts on the rail once the S5 stage is up. A far-low diode reading suggests a short or leaky part on the rail; a far-high one suggests an open path. Neither confirms a bad part on one reading.
PP3V3_S5_SMC_VDDA0.360––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA — a 3.3 V rail in the S5 standby stage, from its name: the SMC's analog supply (VDDA) in the S5 state. The archive lists one known-good reading: diode 0.360 to ground, with no condition noted. No known-good voltage reading here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the voltage on the rail.
  • A diode reading far below 0.360 suggests a short or leaky load on the rail; far above it suggests an open path. One reading alone doesn't condemn a part.
  • No known-good voltage value is recorded, so compare against a known-good board or the matching rail on the other side of a pair.
PP3V3_S5_T1390.360––
AI: what PP3V3_S5_T139 is and how to check it

PP3V3_S5_T139 is a 3.3 V standby rail; the S5 suffix places it in the S5 standby stage, and the T139 suffix is just a rail identifier (both from the name).

  • Known-good: diode 0.360 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check: with power off, diode mode from the rail to ground; then power up and measure the DC voltage, expecting about 3.3 V.
  • A diode reading far from 0.360 suggests a short or leak on the rail; a missing voltage with a good diode reading points upstream to the S5 supply or its enable.
PP3V3_S5_TBT_T_SW0.483––
AI: what PP3V3_S5_TBT_T_SW is and how to check it

PP3V3_S5_TBT_T_SW — reference note

  • What it is: a 3.3 V standby (S5) switch rail for the Thunderbolt "T" side, judging from the name (PP = power rail, 3V3 = 3.3 V, S5 = standby stage, TBT_T = Thunderbolt T, SW = switched). The archive lists it under the S5 group but gives no part or net detail.
  • Known-good reading: diode mode to ground 0.483 (no condition recorded). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage on the rail. Compare the diode reading with the 0.483 guide.
  • If far from known-good: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open feed or switch. Confirm with a voltage check before replacing anything.
PP3V3_S5_TBT_X_SW0.483––
AI: what PP3V3_S5_TBT_X_SW is and how to check it
  • What it is: A 3.3 V standby (S5) switched rail feeding the Thunderbolt X side; the S5/SUS stage and TBT_X naming come from the rail name, not from board data.
  • Known-good: diode 0.483 to ground, from the community archive. No known-good voltage reading here.
  • How to check: power off, measure diode mode from PP3V3_S5_TBT_X_SW to ground; then power up and measure the DC voltage on the rail.
  • If far off: a low diode reading or a rail that stays at 0 V with S5 present points to a short or a switch that isn't turning on. Confirm with a second reading before replacing anything.
PP3V3_SUS0.350––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V suspend rail: the "SUS" and S5/SUS standby stage come from its name, so it's a standby supply present before the board fully wakes. The only known-good figure here is a diode reading of 0.350 to ground; there is no known-good voltage reading in this data.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.350.
  • Then power the board and measure the DC voltage on the rail; expect about 3.3 V, but that figure is general, not from this board's data.
  • A diode reading far below 0.350 suggests a short or a leaky part on the rail; far above suggests an open path. One reading alone doesn't condemn a part, so confirm with a second point on the same net.
PP5V_S50.46––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is a 5 V standby rail: the S5 and SUS naming puts it in the suspend/standby group, so it should be present before the board reaches S4 or S0. The only known-good reading here is a diode value of 0.46 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered in diode mode, red probe on ground and black on the rail, and compare with 0.46. A much lower reading suggests a short or a leaky part on the rail; a much higher one can mean an open path.
  • Then apply power and measure the voltage on the rail. It should sit near 5 V, but that figure is general, not from this board's data.
  • If the diode value is far off, the usual suspects are a shorted capacitor or a failed regulator feeding the rail. Confirm with a second reading before replacing anything.
PPVIN_SUS_VR5_R0.370––
AI: what PPVIN_SUS_VR5_R is and how to check it

PPVIN_SUS_VR5_R — from the name, a 5V regulator input rail in the SUS (standby) domain, so it should be present in standby before the board fully wakes.

  • Known-good: diode-to-ground 0.370 (community reading, a guide only). No known-good voltage reading here.
  • Check: board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • A diode reading far below 0.370 suggests a short or leaky load on the rail; far above suggests an open path to it. Confirm with a second point on the same net before suspecting a part.

S4 18

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V8_S40.430––
AI: what PP1V8_S4 is and how to check it

PP1V8_S4 is a 1.8 V rail in the S4 startup stage, from its name. The archive lists a known-good diode reading of 0.430 (community value, a guide only); no known-good voltage reading is recorded here.

  • With the board unpowered, measure diode mode from PP1V8_S4 to ground and compare with 0.430.
  • Then apply power and check the rail sits near 1.8 V when the board reaches S4.
  • A diode reading far below 0.430 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken path to the rail. One reading alone doesn't prove a part bad, so confirm with the voltage measurement before replacing anything.
PP3V3_S40.329––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 — 3.3 V S4 rail (820-00928)

  • The name marks it as a 3.3 V rail that comes up at the S4 stage of the power sequence, after the S5 rails and before S3/S0. That's from the name, not from a schematic.
  • Known-good from the readings archive: diode 0.329 to ground. No known-good voltage reading is recorded here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.329. Then power the board and confirm about 3.3 V, with PM_SLP_S4_L asserted.
  • A diode reading far below 0.329 suggests a short or a leaky part on the rail; far above it suggests an open trace or missing connection. A missing voltage with a good diode reading points to the S4 enable or the rail's regulator, not the rail itself.
PP3V3_S4_BT0.330––
AI: what PP3V3_S4_BT is and how to check it

PP3V3_S4_BT — 3.3 V S4 rail (820-00928)

  • The name indicates a 3.3 V rail that comes up at the S4 stage of the power sequence. The "BT" suffix is likely a load or switch tag, but that isn't confirmed by the data.
  • Known-good reading: diode 0.330 in diode mode to ground. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.330 usually points to a short or a faulty load on that rail; a missing voltage with a normal diode reading points upstream, at the S4 enable or the rail's source.
PP3V3_S4_MESA_SW0.330––
AI: what PP3V3_S4_MESA_SW is and how to check it

PP3V3_S4_MESA_SW — a 3.3 V rail in the S4 startup stage, from its name. "MESA" and "SW" suggest a switched branch (general naming, not from this board's data), so it likely comes up only after its switch is enabled.

  • Known-good: diode 0.330 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage, comparing against PP3V3_S4 if that rail is present.
  • A diode reading far from 0.330 suggests a short or open on the rail or its switch; a missing voltage with a good diode reading points at the switch enable or upstream S4 supply. Likely causes only, not confirmed.
PP3V3_S4_SOC_PMU0.379––
AI: what PP3V3_S4_SOC_PMU is and how to check it

PP3V3_S4_SOC_PMU — reference note

  • What it is: a 3.3 V rail in the S4 startup stage, from its name. The "SOC_PMU" part suggests it feeds the PMU section of the SoC, but that's from the name only; the parts on this net aren't known here.
  • Known-good reading: diode 0.379 (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage. It should come up when the board reaches S4, after S5 and the PM_SLP_S4_L hand-off.
  • If it's far off: a much lower diode reading points to a short or a failing part on the rail; a missing voltage with a normal diode reading points to the S4 enable or the regulator feeding it. Confirm with a second measurement before replacing anything.
PP3V3_S4_T1510.331––
AI: what PP3V3_S4_T151 is and how to check it

PP3V3_S4_T151 is a 3.3 V rail in the S4 startup stage, judging from its name (PP = power rail, 3V3 = 3.3 V, S4 = the S4 state). The only known-good reading in the archive is a diode value of 0.331; there is no known-good voltage reading here.

  • Diode check: with the board unpowered, measure in diode mode from the rail to ground. A value near 0.331 is the guide; far lower (near 0) suggests a short to ground, and far higher or open suggests a broken path.
  • Voltage check: with power applied and the board brought into S4, measure the rail; it should sit near 3.3 V, but no known-good figure is recorded here, so compare against a matching rail or a known-good board.
  • A reading far from known-good usually points to a shorted load or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part.
PP3V3_S4_TPAD0.34––
AI: what PP3V3_S4_TPAD is and how to check it

PP3V3_S4_TPAD is a 3.3 V rail that comes up at the S4 stage of the power sequence, as the name indicates. The "TPAD" part of the name suggests it feeds the trackpad circuitry, but that is general inference, not confirmed by the board data.

  • Known-good: diode reading 0.34 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • To check: power off, measure diode mode from the rail to ground and compare with 0.34. Then power on and measure the voltage at the rail.
  • A diode reading far below 0.34 usually points to a short or a leaky part on the rail; a much higher reading can mean an open path. A missing or low voltage with power applied points to the S4 enable or the supply feeding the rail, not necessarily the rail itself.
  • The 0.34 is a community guide and varies with board state, so confirm against a matching rail or a known-good board before replacing anything.
PP3V3_S4_WLAN0.330––
AI: what PP3V3_S4_WLAN is and how to check it

PP3V3_S4_WLAN — 3.3 V WLAN rail, S4 stage. The name indicates a 3.3 V rail feeding the wireless section, enabled in the S4 (suspend-to-RAM) power state. This is from the rail name only; the parts it feeds aren't listed here.

  • Known-good: diode-to-ground reading of 0.330 (community value, a guide only, no condition recorded). No known-good voltage reading here.
  • Check: with the board unpowered, diode mode from PP3V3_S4_WLAN to ground. Then power up into S4 and measure the voltage — expect about 3.3 V.
  • Far from known-good: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open feed or missing enable. Confirm with the voltage measurement before replacing anything.
PP3V3_S4_WLAN_SW0.310––
AI: what PP3V3_S4_WLAN_SW is and how to check it

PP3V3_S4_WLAN_SW is a 3.3 V rail in the S4 startup stage, a switched supply for the WLAN section; the S4 and WLAN parts come from the name. The only known-good reading here is a diode value of 0.310 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. With the board unpowered, measure diode mode from the rail to ground and compare with 0.310; then power up and check for about 3.3 V, which is general expectation from the name, not a recorded value. A diode reading far below 0.310 suggests a short or leaky load on the rail, while a much higher one can mean an open path or a missing part. Treat these as a guide only, since readings vary with board state.

PP3V3_S4SW_SNS0.550––
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail in the S4 startup stage, from its name: a switched 3V3 supply with a sense line. The only known-good reading recorded is a diode value of 0.550 to ground; no known-good voltage reading here.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.550.
  • Then power the board and measure the DC voltage on the rail; the data has no known-good voltage, so compare with a matching rail or a known-good board.
  • A diode reading far below 0.550 suggests a short or a leaky part on the rail; far above suggests an open path or a missing connection. One reading alone doesn't confirm a bad part.
PP3V3_S4SW_SNS_FET_R0.550––
AI: what PP3V3_S4SW_SNS_FET_R is and how to check it

PP3V3_S4SW_SNS_FET_R — reference note

  • What it is: a 3.3 V rail in the S4 startup stage, judged from the name (S4 = the S4 power state; SW_SNS = switched-rail sense; FET_R = the FET side of that switch). It sits alongside PP3V3_S4SW_SNS and PP3V3_S4 in the S4 group.
  • Known-good reading: diode 0.550 to ground, from the community archive. No known-good voltage reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail — compare with 0.550. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on that rail; a much higher one to an open path. A single reading isn't proof a part is bad — confirm with the voltage measurement before replacing anything.
PP5V_S40.425.000–
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage; the "S4" part comes from the rail name, and S4 is a sleep/standby state that comes up before S0. The archived reading for this board is diode 0.42 and voltage 5.000, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from PP5V_S4 to ground, then power the board and measure the voltage. A diode reading far below 0.42 suggests a short or a leaky load on the rail; a voltage well under 5 V points to the rail not being enabled or its source being loaded down. There is no known-good resistance reading for this rail here, so compare against a matching rail or a known-good board.

PP5V_S4_ISNS_DOL––
AI: what PP5V_S4_ISNS_D is and how to check it

PP5V_S4_ISNS_D — the name indicates a 5V rail in the S4 startup stage, with "ISNS" suggesting a current-sense node (general naming convention, not from this board's data). The only known-good reading recorded here is a diode reading of OL to ground; no voltage or resistance value is recorded.

  • With the board unpowered, measure diode mode from PP5V_S4_ISNS_D to ground and compare with the recorded OL. A low or shorted reading where OL is expected points to a short on that net or its sense path.
  • Then power the board and check the voltage on the rail; no known-good voltage is recorded here, so compare against the matching rail on the other side of the pair if one exists.
  • A reading far from known-good usually means a shorted component or a failed switch feeding the rail, but that's a likely cause, not a confirmed one.
PP5V_S4_T_USBC0.2505.000–
AI: what PP5V_S4_T_USBC is and how to check it

PP5V_S4_T_USBC is a 5 V USB-C rail in the S4 startup stage, judging from the name (S4 = the stage after S5, before S3/S0). Known-good from the readings archive: diode 0.250 to ground and 5.000 V with power applied; no known-good resistance reading here.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.250. A much lower value suggests a short on the rail; a much higher one suggests an open feed.
  • With power applied, check for 5.000 V. Missing or low voltage points upstream to the rail's enable or source, not necessarily the rail itself.
  • These are community readings and vary with board state, so treat them as a guide and compare against a matching rail on the other side of the pair where possible.
PP5V_S4_TPAD_CONN0.42––
AI: what PP5V_S4_TPAD_CONN is and how to check it

PP5V_S4_TPAD_CONN is a 5V rail in the S4 startup stage, feeding the trackpad connector; the S4 stage and TPAD function come from the name. The only known-good reading here is diode 0.42 to ground, with no condition noted; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.42.
  • Then power the board and measure the voltage on the rail; it should come up when the board reaches S4.
  • A diode reading far below 0.42 suggests a short or a failing load on the rail; far above suggests an open path. One reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.
PP5V_S4_X_USBC0.2415.000–
AI: what PP5V_S4_X_USBC is and how to check it

PP5V_S4_X_USBC — reference note

  • What it is: a 5 V rail in the S4 startup stage, from the name (S4 = suspend-to-RAM stage; X_USBC = the "X" USB-C side). It's listed under the S4 rails alongside PP5V_S4_T_USBC.
  • Known-good readings (community guide): diode 0.241 to ground, and 5.000 V with the board powered and in S4. No known-good resistance value here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage.
  • If far off: a low diode reading or missing 5 V usually points to a short or a rail that isn't being enabled in the S4 sequence — check the upstream S4 rails and enable signals before suspecting a part.
PPBUS_S4_HS_TPAD0.35712.600–
AI: what PPBUS_S4_HS_TPAD is and how to check it

PPBUS_S4_HS_TPAD is a trackpad-related power rail in the S4 startup stage; the "S4" and "TPAD" parts come from the rail name, and "HS" likely means high-side switch (general reading, not from board data). Known-good readings here are diode 0.357 and voltage 12.600, community-contributed and a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.357 usually points to a short or a leaky part on that rail, but confirm with more than one reading before replacing anything. No known-good resistance value is listed for this rail.

PPVIN_S4_TPAD_FUSE0.35712.600–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE — the name indicates a fused input feed for the trackpad supply in the S4 (suspend-to-RAM) startup stage on this 820-00928. It's a feed rail, not a regulated output, so it should sit near the adapter/battery bus voltage rather than a fixed low value.

Known-good readings from the archive: diode 0.357 to ground, and 12.600 V with power applied.

To check it: power off and unplug, then measure diode mode from the rail to ground; then power up and measure the voltage. A diode reading far from 0.357 suggests a short or leaky part on that rail; a voltage far from 12.600 V suggests the fuse or its upstream feed is open or not being enabled. No known-good resistance reading is recorded for this rail.

S3: memory 10

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.700––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it

PP0V6_S3_MEM_VREFCA_A — the name says it's a 0.6 V reference (VREF) for the memory (MEM) address/command lines (CA), enabled in the S3 sleep/standby stage. It's a small reference rail, not a main power rail.

  • Known-good reading: diode 0.700 to ground (community value, guide only; no condition recorded).
  • How to check: power off, measure diode mode from the net to ground and compare with 0.700. Then power on and measure the DC voltage — it should sit near the 0.6 V its name implies (general expectation, not a recorded value here).
  • No known-good voltage reading here for this net, so compare against a matching memory reference net or a known-good board.
  • A diode reading far below 0.700 usually points to a short or leaky part on the net; a far higher or open reading points to a broken connection. Confirm with the voltage check before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.750––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it
  • What it is: PP0V6_S3_MEM_VREFDQ_A is a memory reference rail, from its name: the "0V6" is a 0.6 V level, "S3" puts it in the memory/S3 startup stage, and "VREFDQ" is the DDR data reference voltage. It is one of a pair with PP0V6_S3_MEM_VREFDQ_B.
  • Known-good reading: diode 0.750 to ground, from the community readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.750; then power up into S3 and measure the DC voltage, which should sit near the 0.6 V the name implies (general expectation, not a recorded value).
  • If it's far off: a low diode reading or a collapsed voltage usually points to a short or a failed reference divider/decoupling part on that net, but one reading isn't proof. Compare against PP0V6_S3_MEM_VREFDQ_B and PP0V6_S3_MEM_VREFCA_A to see whether the fault is shared or local.
PP0V6_S3_MEM_VREFDQ_B0.750––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B is a memory reference-voltage rail: the "S3" in its name marks it as a memory-rail in the S3 (suspend-to-RAM) stage, and "VREFDQ" is the DDR data-reference level, nominally around 0.6 V by name. The only known-good reading here is a diode value of 0.750 to ground; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode, black probe on ground and red on the rail, and compare with the 0.750 guide; then power up and measure the DC voltage, which should sit near the 0.6 V the name implies. A diode reading far from 0.750 usually points to a short or a leaky part on that net, but one reading alone doesn't condemn anything — compare with the matching PP0V6_S3_MEM_VREFDQ_A and PP0V6_S3_MEM_VREFCA_A rails before replacing parts.

PP1V0_S30.228––
AI: what PP1V0_S3 is and how to check it

PP1V0_S3 is a 1.0 V rail in the S3 (memory) startup stage, judged from its name; the board data lists it under S3 with a diode reading of 0.228 to ground.

  • Diode check: board unpowered, diode mode, red probe on ground, black on PP1V0_S3. The known-good figure is 0.228; treat it as a community guide, not a guaranteed value.
  • Voltage check: with power applied and the board in S3, measure PP1V0_S3 to ground. No known-good voltage reading exists here, so compare against a matching rail on a known-good board.
  • Far from 0.228: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. No known-good resistance reading exists here either.
PP1V2_S30.2371.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 — 1.2 V S3 rail (820-00928)

  • The name says it's a 1.2 V rail in the S3 (memory) startup stage; the S3 grouping in the notes also lists PP1V2_S3_CPUDDR and PP1V2_S3_REG_R, so it's tied to the CPU DDR supply area (general reading of the names).
  • Known-good readings from the archive: diode 0.237 to ground, and 1.200 V with the board powered in S3. No known-good resistance value is recorded here.
  • Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage; compare against those two figures.
  • A diode reading far below 0.237 suggests a short or leaky load on the rail; a voltage well off 1.200 V in S3 points to the rail's regulator or its enable, not the rail itself. One reading alone doesn't condemn a part — confirm with a second measurement before replacing anything.
PP1V2_S3_CPUDDR0.250––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR — from the name, a 1.2 V rail for the CPU's DDR memory, in the S3 (memory/suspend-to-RAM) startup stage.

  • Known-good reading here: diode mode to ground 0.250 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • Check with the board unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.250.
  • Then power the board and measure the voltage on the rail; it should sit near 1.2 V once the board reaches S3. No known-good powered voltage is recorded here, so compare against a matching rail or a known-good board.
  • A diode reading far from 0.250 usually points to a short or a damaged part on that rail, but one reading isn't proof — confirm with a second measurement before replacing anything.
PP1V2_S3_REG_R0.2351.200–
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R is a 1.2 V regulator rail in the S3 (memory) startup stage, judging from its name. Known-good readings here: diode 0.235 and voltage 1.200.

  • Check it unpowered in diode mode from the rail to ground; a far lower reading than 0.235 suggests a short or a leaky part on the rail, a far higher one an open path.
  • With power applied, measure 1.200 V; this rail should only be present once the board has reached S3, so a missing voltage before that point is expected.
  • No known-good resistance reading is recorded for this rail, so compare against a matching rail or a known-good board.

A single reading off the mark is only a guide, not proof a part is bad.

PP1V8_S30.358––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail in the S3 (memory) startup stage, judging from its name; it sits alongside PP1V8_S3_MEM in the S3 group. The only known-good reading here is a diode value of 0.358, with no condition recorded; no known-good voltage reading exists in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.358 usually points to a short or a leaky part on the rail, while a far higher one can mean an open path; treat these as guides, not proof. No known-good voltage is listed, so compare against a matching rail or a known-good board of the same model.

PP1V8_S3_MEM0.377––
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM — 820-00928

  • From its name, this is a 1.8 V memory rail that comes up in the S3 (suspend-to-RAM) stage, so it should be present whenever the board is in S3 or S0.
  • Known-good reading in the archive: diode mode to ground 0.377. No known-good voltage reading here, and no condition is recorded for that diode value.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the DC voltage on the rail, comparing against a matching memory rail on a known-good board if you have one.
  • A diode reading far below 0.377 usually points to a short or a failing part on the rail; far above it suggests an open trace or missing connection. Treat both as a guide, not a verdict — confirm with a second measurement before replacing anything.
PP3V3_S3_DPMUX_UC_R0.333––
AI: what PP3V3_S3_DPMUX_UC_R is and how to check it
  • What it is: PP3V3_S3_DPMUX_UC_R is a 3.3 V rail that comes up at the S3 stage, which from its name is the memory stage of startup. The "_DPMUX_UC" part suggests a display-port multiplexer and its microcontroller, but that is from the name only, not confirmed by board data.
  • Known-good reading: diode 0.333 to ground, from the readings archive. There is no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.333; then power up and measure the voltage, expecting about 3.3 V once the board reaches S3.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail, while a missing voltage at S3 points back to the S3 enable and upstream rails. These are general guidelines, not confirmed causes.

S0: running 54

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.140––
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT — reference note

  • What it is: from the name, a 0.6 V DDR termination rail that comes up in the S0 (running) state. The "VTT" part is general knowledge: it's the termination voltage for the memory data bus, usually about half the DDR supply.
  • Known-good reading: diode mode to ground 0.140 (from the readings archive; a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.140. Then power up into S0 and measure the DC voltage — it should sit near 0.6 V, though no known-good voltage is recorded for this board.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail; a correct diode reading with no voltage points more to the rail's enable or supply. Confirm with a second measurement before replacing anything.
PP1V0_S0SW0.235––
AI: what PP1V0_S0SW is and how to check it

PP1V0_S0SW is a 1.0 V rail; the "S0" in its name marks it as a running-state rail, and "SW" usually means it comes from a switched regulator (that part is general naming, not from the board data). The only known-good reading here is a diode value of 0.235 to ground; no known-good voltage reading is recorded for this rail.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.235. A much lower reading suggests a short or a leaky part on the rail; a much higher one can mean an open feed or a missing part.
  • Then power the board and measure the DC voltage on the rail. No known-good voltage is listed, so treat roughly 1.0 V as the expected target from the name only, and confirm against a matching rail or a known-good board.
  • A voltage far off target with a normal diode reading points more to the regulator's enable or feed than to a shorted load. Which parts sit on this net isn't recorded, so trace it on the board before replacing anything.
PP1V2_S0SW0.239––
AI: what PP1V2_S0SW is and how to check it

PP1V2_S0SW — a 1.2 V rail in the S0 (running) state; the S0 part comes from the name, and "SW" usually means a switched rail (general naming, not from this board's data).

  • Known-good: diode 0.239 to ground, from the readings archive. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage on the rail.
  • A diode reading far below 0.239 suggests a short or a leaky load on the rail; far above it suggests an open path. Treat one reading as a guide only and compare with a matching rail before replacing anything.
PP1V5R1V35_S0_GPU_IC0.172––
AI: what PP1V5R1V35_S0_GPU_IC is and how to check it
  • What it is: A GPU core rail, judged from the name: 1.5 V / 1.35 V selectable, S0 (running) state, feeding the GPU IC. The exact parts on the net aren't known here.
  • Known-good: diode reading 0.172 in diode mode. No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then diode mode from PP1V5R1V35_S0_GPU_IC to ground. Power up and measure the voltage in S0; compare with PP1V5R1V35_S0_GPU_MEM and the GPU rails PP1V8_S0_GPU and PP3V3_S0_GPU.
  • If far off: a shorted or open line, or the GPU rail not coming up in sequence. Check P3V3_S0GPU_PGOOD and P5_S0GPU_PGOOD first. These are community readings and only a guide.
PP1V5R1V35_S0_GPU_MEM0.1741.500170.000
AI: what PP1V5R1V35_S0_GPU_MEM is and how to check it

PP1V5R1V35_S0_GPU_MEM — the name indicates a 1.5 V / 1.35 V GPU memory rail that is active in S0 (running). The "S0" stage comes from the name.

  • Known-good readings (community guide): diode 0.174, voltage 1.500 V, resistance 170.000. No condition is recorded for these.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a short or a failing load on the rail; a missing or low voltage with a normal diode reading points more toward the supply side.
  • No known-good reading of another kind is available here, so compare against a matching rail or a known-good board before condemning anything.
PP1V8_S00.3401.800–
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail in the S0 (running) state, judging from its name; the board data doesn't say which parts it feeds. Known-good readings for this rail: diode 0.340 to ground and 1.800 V with the board powered in S0. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.340 suggests a short or a failing load on the rail; a voltage well off 1.800 V points to the rail not coming up or being loaded down. No known-good resistance reading here, so compare against a matching rail or a known-good board.

PP1V8_S0_GPU0.200––
AI: what PP1V8_S0_GPU is and how to check it

PP1V8_S0_GPU — reference note

  • From the name: a 1.8 V rail in the S0 (running) state, feeding the GPU. The "S0" tells you it should only be up once the board is fully running, not in suspend or standby.
  • Known-good reading in the archive: diode mode to ground 0.200. No known-good voltage reading here.
  • Check it unpowered first: diode mode, black probe on ground, red on the rail, and compare with 0.200. Then apply power and confirm about 1.8 V once the board is in S0.
  • A diode reading far from 0.200 usually points to a short or a damaged load on the rail, but one reading isn't proof — compare against a matching GPU rail before condemning anything.
PP1V8_S0_GPU_LC_IC0.200––
AI: what PP1V8_S0_GPU_LC_IC is and how to check it
  • What it is: PP1V8_S0_GPU_LC_IC is a 1.8 V GPU-related rail that comes up in the S0 (running) state, judged from the name (PP = power rail, 1V8 = 1.8 V, S0 = running, GPU = graphics). The "LC_IC" suffix is not explained in the available data.
  • Known-good reading: diode-to-ground 0.200 in the readings archive. No known-good voltage reading here.
  • How to check: with the board powered off, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.200 suggests a short or a failing load on the rail; a missing voltage with a normal diode reading points to the rail not being enabled or its supply not coming up. Confirm with a second measurement before replacing anything.
PP1V8_S0_LDO_AUD0.396––
AI: what PP1V8_S0_LDO_AUD is and how to check it

PP1V8_S0_LDO_AUD is a 1.8 V rail; the "1V8" and "LDO" come from the name, and "S0" places it in the running state. The only known-good figure here is a diode reading of 0.396 to ground, with no condition recorded. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check for about 1.8 V. No known-good voltage reading is listed for this rail. A diode value far from 0.396 points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault.

PP1V8_S0_PCH_VCCHDA_F0.3401.800–
AI: what PP1V8_S0_PCH_VCCHDA_F is and how to check it

PP1V8_S0_PCH_VCCHDA_F — a 1.8 V rail. From the name: S0 means it belongs to the running state, PCH is the chipset, and VCCHDA is a PCH supply; the _F suffix is a rail variant. General knowledge, not from the board data: it's a chipset-side rail that should only be present once the board is in S0.

  • Known-good readings (community archive, guide only): diode 0.340 to ground, voltage 1.800.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A voltage well off 1.800 with the board in S0, or a diode reading far from 0.340, points at a short or a missing supply/enable to that rail rather than the rail itself. No known-good resistance reading here; compare with a matching rail or a known-good board.
PP1V8_S0SW_DFR0.531.800–
AI: what PP1V8_S0SW_DFR is and how to check it
  • What it is: PP1V8_S0SW_DFR is a 1.8 V switched rail. The S0 part of the name marks it as a running-state (S0) rail; the SW and DFR parts suggest a switched supply, but the exact function isn't in the data. That reading is from the name only.
  • Known-good readings (community guide): diode 0.53 to ground, and 1.800 V with the board powered in S0.
  • How to check: with the board off and unpowered, measure diode mode from the rail to ground and compare with 0.53. Then power up and measure the voltage; it should sit at 1.800 V.
  • If it's far off: a much lower diode reading points to a short or a leaky part on the rail; 0 V or a wrong voltage with power on points to the rail not being enabled or its supply failing. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP3V3_S00.32––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is a 3.3 V rail that comes up in the S0 (running) state, as the name indicates; it's one of the main always-on-while-awake rails on this board.

  • Known-good reading: diode mode to ground 0.32 (community guide; no condition recorded). No known-good voltage value here.
  • Check it unpowered in diode mode to ground first, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.32 can suggest a short or a damaged part on that net, but one reading isn't proof — compare with a matching S0 rail before replacing anything.
  • No known-good voltage is listed for this rail, so compare against a known-good board or the rail's expected level.
PP3V3_S0_AUD_F0.653––
AI: what PP3V3_S0_AUD_F is and how to check it

PP3V3_S0_AUD_F — a 3.3 V rail for the audio section, active in S0 (running), judging from the rail name. The only known-good reading here is a diode value of 0.653 to ground; there is no known-good voltage reading for this rail.

  • Check (board unpowered): diode mode, red probe on ground, black on the rail. Compare with 0.653 — a guide only, since community readings vary with board state.
  • Check (powered, in S0): measure DC volts on the rail; expect about 3.3 V, though no known-good voltage is recorded here.
  • Far from known-good: a much lower diode reading usually points to a shorted load or capacitor on the rail; an open reading points to a missing feed or enable. Confirm with the voltage measurement before replacing anything.
PP3V3_S0_CARBON_ROL––
AI: what PP3V3_S0_CARBON_R is and how to check it
  • What it is: A 3.3 V rail that is active in the S0 (running) state, based on the name; "CARBON" is a board-specific label and its exact load isn't documented here.
  • Known-good readings: The archive lists diode OL for this net. No known-good voltage reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from PP3V3_S0_CARBON_R to ground; then power up into S0 and measure the voltage, which should be about 3.3 V.
  • What a far-off reading suggests: A short or very low diode reading points to a fault on the rail or its load; an open reading like the recorded OL is the expected unpowered state, so confirm it against the powered voltage before suspecting a part.
PP3V3_S0_CPUTHMSNS_R0.402––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding the CPU thermal sensor sense circuit; the _R suffix usually marks a resistor-linked sense line. This is inferred from the name, not from board data.
  • Known-good reading: diode 0.402 to ground (community archive, board state not stated). No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground and compare with 0.402; then power on into S0 and measure the voltage, expecting about 3.3 V from the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage points upstream to the S0 supply or enable. Treat it as a guide and confirm before replacing anything.
PP3V3_S0_DPMUX_UC_R0.358––
AI: what PP3V3_S0_DPMUX_UC_R is and how to check it
  • What it is: a 3.3 V rail that is up in the S0 (running) state, from the name. The DPMUX_UC part suggests it feeds a display-mux/embedded-controller section, but that is general inference, not from this board's data.
  • Known-good: diode reading 0.358 to ground, with no stated condition. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on into S0 and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a correct diode reading with no voltage points upstream to its enable or source supply. No known-good resistance value here, so compare against a matching rail on a known-good board.
PP3V3_S0_GPU0.496––
AI: what PP3V3_S0_GPU is and how to check it

PP3V3_S0_GPU — 3.3 V GPU rail, S0 (running) state. The name says it: a 3.3 V supply for the GPU domain, active in S0. It sits in the S0 group alongside P3V3_S0GPU_PGOOD and P5_S0GPU_PGOOD, so it is expected to come up with the GPU power sequence once the board is fully on.

  • Known-good: diode-to-ground 0.496 (community reading, a guide only). No known-good voltage or resistance value here.
  • Check it: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage on the rail; compare the diode reading against a matching rail or a known-good board if yours differs.
  • Far from known-good: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no voltage points at the rail's enable or its source, not the rail itself. Confirm with a second measurement before replacing anything.
PP3V3_S0_GPUTHMSNS_R0.382––
AI: what PP3V3_S0_GPUTHMSNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail feeding the GPU thermal sensor circuit. The data only lists the net; it doesn't show which parts sit on it.
  • Known-good reading: diode 0.382 to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from PP3V3_S0_GPUTHMSNS_R to ground and compare with 0.382; then power on in S0 and measure the voltage, which should be about 3.3 V.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to the rail's source or its enable. Treat these as likely causes, not confirmed ones.
PP3V3_S0_LEFT0.339––
AI: what PP3V3_S0_LEFT is and how to check it

PP3V3_S0_LEFT is a 3.3 V rail that comes up in the S0 (running) state, judging from its name; the "LEFT" suffix suggests it feeds the left-hand side of the board, but the exact loads aren't documented here.

  • Known-good: diode-to-ground 0.339 (community reading, a guide only; varies with board state). No known-good voltage reading is recorded here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.339.
  • Then power up and measure the voltage; it should sit near 3.3 V in S0.
  • A diode reading far below 0.339 suggests a short or a failing load on the rail; a much higher or open reading suggests a broken trace or missing part. Confirm with a second measurement before replacing anything.
PP3V3_S0_TBTTHMSNS_T_R0.401––
AI: what PP3V3_S0_TBTTHMSNS_T_R is and how to check it

PP3V3_S0_TBTTHMSNS_T_R — a 3.3 V S0 (running-state) rail; the name suggests a Thunderbolt thermal-sense supply on the T side, but that's from the name only. Known-good: diode 0.401 to ground, no known-good voltage reading here.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail (or the reverse of your usual convention — compare the same polarity as the 0.401 figure).
  • Then power up and measure the voltage; expect about 3.3 V while the board is in S0.
  • A diode reading far below 0.401 suggests a short or leaky part on the rail; far above suggests an open path. Compare against PP3V3_S0_TBTTHMSNS_X_R on the other side of the pair before condemning anything.
PP3V3_S0_TBTTHMSNS_X_R0.385––
AI: what PP3V3_S0_TBTTHMSNS_X_R is and how to check it

PP3V3_S0_TBTTHMSNS_X_R is a 3.3 V S0 (running-state) rail; from the name it's a Thunderbolt thermal-sense supply ("TBTTHMSNS"), with the "_X" likely marking one side of the pair. The only known-good reading here is a diode-mode value of 0.385 to ground, with no condition noted; there's no known-good voltage reading for this rail.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.385.
  • Then power the board and measure the voltage; expect about 3.3 V while the board is in S0.
  • A diode reading far below 0.385 suggests a short or leaky part on the rail; far above suggests an open path. Compare against the matching PP3V3_S0_TBTTHMSNS_T_R rail before condemning anything.
PP3V3_S0SW_DFR0.580––
AI: what PP3V3_S0SW_DFR is and how to check it

PP3V3_S0SW_DFR — 820-00928

  • What it is: a 3.3 V switched rail. From the name: 3V3 = 3.3 V, S0 = running state, SW = switched, DFR = a suffix used on this board's rail list. It is only expected up once the board is in S0 (running).
  • Known-good reading: diode 0.580 (community archive, guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from PP3V3_S0SW_DFR to ground. Then power up into S0 and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; no voltage in S0 suggests the switch or its enable is missing. No known-good voltage here, so compare with a matching S0 3V3 rail or a known-good board.
PP3V3_S0SW_LCD0.576––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a switched 3.3 V LCD rail in the S0 (running) state, judged from its name; the "SW" suggests it is gated on rather than always present. The only known-good reading here is a diode value of 0.576 to ground, with no condition recorded. Check it unpowered in diode mode to ground, then with power applied confirm it comes up only in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.576 usually points to a short or leak on the rail or its load, but one reading alone doesn't confirm a bad part.

PP3V3_S0SW_LCD_R0.574––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R — from the name, a switched 3.3 V rail for the LCD, active in the S0 (running) state; the "_R" suffix usually marks the resistor-side branch of that switch, though the exact topology isn't in this data.

  • Known-good: diode reading to ground 0.574 (board unpowered). No known-good voltage reading here.
  • Check it: power off, diode mode, black probe to ground, red on the rail — compare with 0.574. Then power on and measure the voltage; it should come up only once the board is in S0.
  • Far from 0.574: a much lower diode reading points to a short or leaky part on the rail; a much higher one to an open path or a missing feed. A single off reading isn't proof — confirm with the voltage measurement and compare against the matching switched LCD rail before replacing anything.
PP3V3_TBT_T_S00.3503.300–
AI: what PP3V3_TBT_T_S0 is and how to check it

PP3V3_TBT_T_S0 is a 3.3 V rail; the "TBT" and "S0" in the name indicate it is a Thunderbolt-side supply that is up in the S0 (running) state. Known-good readings from the archive: diode 0.350 to ground, and 3.300 V with the board powered in S0.

To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage in S0. A diode reading well below 0.350 suggests a short or a leaky load on the rail; a voltage far from 3.300 V with the board in S0 points to the rail's regulator or its enable. These are community readings and only a guide, so compare against a known-good board if you can.

PP3V3_TBT_X_S00.3403.300–
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt side X, in the S0 running state; that reading comes from the rail's name, not from a schematic. Known-good community readings are about 0.340 in diode mode to ground and 3.300 V with the board powered in S0, both a guide only. Check it unpowered in diode mode from the rail to ground, then power up into S0 and measure the voltage. A diode reading far below 0.340 suggests a short or leaky load on the rail; a missing 3.300 V with a normal diode reading points upstream at the rail's enable or supply. No known-good resistance reading here, so compare against a matching rail or a known-good board.

PP5V_S00.380––
AI: what PP5V_S0 is and how to check it

PP5V_S0 — the name indicates a 5 V rail in the S0 (running) state, so it should be present only once the board is fully powered on.

  • Known-good reading in the archive: diode 0.380 (diode mode to ground). No known-good voltage reading is recorded here.
  • Check it unpowered first: meter in diode mode, black probe on ground, red on the rail, and compare with 0.380. Then apply power and confirm roughly 5 V in S0.
  • A diode reading far below 0.380 suggests a short or a leaky load on the rail; far above suggests an open path. A missing 5 V with a good diode reading points more to the rail's enable or source than to the rail itself.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PP5V_S0_ALSCAM_F0.41––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F — 820-00928 reference note

  • What it is: a 5 V rail that is switched on in the S0 (running) state, per its name; the "ALSCAM" part suggests it feeds the camera/ALS area, but that is from the name only, not confirmed by board data.
  • Known-good reading: diode 0.41 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.41; then power up and confirm about 5 V is present in S0.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on that rail; a missing 5 V with a good diode reading points upstream, to the enable or switch feeding it. Treat 0.41 as a guide only, since readings vary with board state.
PP5V_S0_BKLT_A0.382––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is a 5 V rail that feeds the display backlight, and the S0 in its name marks it as a running-state rail. The only known-good reading here is a diode value of 0.382; there is no known-good voltage reading for this rail. Check it in diode mode to ground with the board unpowered, then measure the voltage with power applied and the board in S0. A diode reading far below 0.382 usually points to a short or a leaky part on the rail, while a correct diode reading with no 5 V present points upstream to the backlight supply or its enable.

PP5V_S0_BKLT_D0.382––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D — a 5 V backlight rail. The name says it's a 5 V rail (PP5V) that comes up in the S0 running state, and the BKLT_D suffix marks it as the display-side backlight feed. Known-good: diode reading 0.382 to ground, with no condition recorded.

  • Check it unpowered in diode mode, red probe on ground, black on the rail; compare with 0.382.
  • Then power the board and measure the DC voltage on the rail — no known-good voltage reading here, so compare against a known-good board or the matching backlight rail on the other side of the pair.
  • A diode reading far below 0.382 suggests a short or leaky part on the rail; far above suggests an open path. Neither is confirmed on one reading, so check the voltage next before replacing anything.
PP5V_S0_FAN_CONN0.386––
AI: what PP5V_S0_FAN_CONN is and how to check it

PP5V_S0_FAN_CONN is the 5 V fan connector rail, enabled in the S0 (running) state — the S0 part comes from the rail's name. The only known-good reading here is a diode value of 0.386 to ground; there is no known-good voltage reading for this rail.

  • With the board unpowered, measure diode mode from PP5V_S0_FAN_CONN to ground and compare with 0.386. A much lower reading suggests a short on the rail or the fan itself; a much higher one suggests an open path.
  • With power applied in S0, check for about 5 V. No voltage points upstream to the rail's enable or supply, not the fan.
  • These readings are community guides and vary with board state, so a small difference alone doesn't condemn a part.
PP5V_S0_GFXIMVP_VDD0.378––
AI: what PP5V_S0_GFXIMVP_VDD is and how to check it
  • What it is: PP5V_S0_GFXIMVP_VDD is a 5 V rail in the S0 (running) state, feeding the GPU's IMVP supply — the name says this, not the board data.
  • Known-good reading: diode 0.378 (community contribution, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or a failed part on the rail; a missing 5 V with a normal diode reading points back to the rail's enable or source.
PP5V_S0_GFXIMVP_VDDP0.378––
AI: what PP5V_S0_GFXIMVP_VDDP is and how to check it

PP5V_S0_GFXIMVP_VDDP — reference note

  • What it is: a 5 V rail in the S0 (running) power state, feeding the graphics IMVP regulator's VDDP supply. The 5 V level and the S0 stage come from the rail name; the exact load it feeds isn't documented here.
  • Known-good reading: diode mode to ground is 0.378 (community value, a guide only — it varies with board state). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.378; then power up in S0 and confirm roughly 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a missing 5 V with a normal diode reading points upstream to the enable or source feeding it. Confirm with a second measurement before replacing anything.
PP5V_S0_GPU_OPAMPOL––
AI: what PP5V_S0_GPU_OPAMP is and how to check it
  • What it is: PP5V_S0_GPU_OPAMP is a 5 V rail in the S0 (running) state, judging from its name. The "GPU_OPAMP" part suggests it feeds an op-amp in the GPU section, but that is inference from the name only; the parts on this net aren't known.
  • Known-good readings: the archive lists diode OL for this net. There is no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the DC voltage. A diode reading far below OL can suggest a short or a leaky load on the rail, but a single reading isn't proof a part is bad.
  • Next step: confirm the rail is present in S0 and compare its diode reading against a matching 5 V S0 rail, since no voltage reference exists for this net.
PP5V_S0_GPUFETOL––
AI: what PP5V_S0_GPUFET is and how to check it
  • What it is: PP5V_S0_GPUFET is a 5 V S0 (running-state) rail associated with the GPU section, judged from its name; the "GPUFET" part suggests it feeds a switching FET for the GPU supply. The exact parts on it aren't known here.
  • Known-good reading: diode to ground is OL (open, no conduction to ground) in the archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground should read OL; then power up and confirm about 5 V in S0.
  • If it's far off: a low diode reading points to a short on that rail; no 5 V in S0 points upstream to its enable or source FET. Treat this as a guide, not a confirmed fault.
PP5V_S0_KBD0.386––
AI: what PP5V_S0_KBD is and how to check it

PP5V_S0_KBD is a 5 V rail that, judging from its name, powers the keyboard and only comes up in S0 (the running state). The archive lists one known-good diode reading: 0.386 to ground, with no condition noted; there is no known-good voltage reading here. With the board unpowered, measure diode mode from PP5V_S0_KBD to ground and compare with 0.386 — a near-short (very low reading) usually points to a shorted load or capacitor on that rail, while an open reading suggests a broken feed. Then power up in S0 and check for about 5 V; a missing voltage points back to the rail's enable or source rather than the keyboard itself. These readings are community guides and vary with board state, so treat a small difference as normal.

PP5V_S0_T1390.41––
AI: what PP5V_S0_T139 is and how to check it
  • What it is: PP5V_S0_T139 is a 5 V rail in the S0 (running) power state, judged from its name; the T139 suffix likely marks its source or load, but that isn't confirmed here.
  • Known-good: diode reading to ground is 0.41. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S0_T139 to ground and compare with 0.41; then power up and measure the voltage, which should be about 5 V in S0.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail, while a missing voltage with a normal diode reading points upstream to the rail's enable or source.
PP5V_S0GPU_P1V35_GPU0.380––
AI: what PP5V_S0GPU_P1V35_GPU is and how to check it

PP5V_S0GPU_P1V35_GPU is a 5 V GPU-related rail in the S0 (running) state; the S0 part comes from the name, and it sits with the GPU 1V35 rails. The only known-good reading here is diode mode 0.380 to ground, with no stated condition. Check it unpowered in diode mode from the rail to ground, then power the board and confirm about 5 V in the S0 state. No known-good voltage reading here, so compare against a matching GPU rail or a known-good board. A diode reading far below 0.380 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

PP5V_S0SW_LCD0.546––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD — reference note

  • What it is: a 5 V, S0 (running) switched LCD rail; the "S0SW_LCD" part comes from the name, so it's a switched supply for the display section that comes up in the running state. The archive lists it under the S0 rails.
  • Known-good reading: diode mode to ground is 0.546. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from PP5V_S0SW_LCD to ground and compare with 0.546; then power up and measure the voltage, expecting about 5 V while the board is in S0.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no voltage points more to the rail's enable or switch not coming up. Confirm with the voltage measurement before suspecting a part.
PPVCC_S0_CPU0.0031.5001.520R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — the CPU core power rail. The name says it's the CPU's VCC supply, active in the S0 (running) state.

Known-good readings (community guide, condition not stated): diode 0.003, voltage 1.500 V, resistance 1.520R. A very low diode and sub-2-ohm resistance are normal for a core rail feeding a large CPU die.

To check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail once the board is in S0.

A reading far from known-good (much higher diode/resistance, or no voltage in S0) usually points to an open feed, a bad VR controller or its enable, or a shorted load — confirm with a second measurement before replacing anything. No known-good current-draw or ripple reading exists here.

PPVCCGT_S0_CPU0.0051.5002.600R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU — reference note

  • What it is: the CPU graphics (GT) core supply, active in S0 (running). This comes from the rail name; the archive doesn't list which parts sit on the net.
  • Known-good readings (community guide, condition not stated): diode 0.005 to ground, 1.500 V with power applied, 2.600R resistance. Treat these as a guide only, since readings vary with board state.
  • How to check: with the board powered off, measure diode mode from the rail to ground; then power up and measure the voltage. The 0.005 diode reading is very low, so a near-short to ground is expected here and not by itself proof of a fault.
  • If a reading is far off: a voltage well below 1.500 V under load points to the supply or its enable, not necessarily the CPU. No known-good current-draw or ripple value is available for this rail, so compare against a matching rail or a known-good board before condemning anything.
PPVCCIO_S0_CPU0.0700.950–
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU — reference note

  • What it is: an S0 (running-state) CPU I/O supply rail; the "VCCIO" and "S0" parts come from the rail name, and it is listed among this board's S0 rails.
  • Known-good readings (community guide): diode 0.070 to ground, voltage 0.950 V. No known-good resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading or a missing/incorrect voltage points to a short or a supply not coming up, but one reading alone doesn't confirm a bad part — compare against a matching rail or a known-good board before replacing anything.
PPVCCSA_S0_CPU0.0151.1507.690R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU — the name indicates the CPU's system-agent supply rail, active in S0 (running) state. General naming convention, not from this board's data.

Known-good readings from the archive (guide only, board state varies):

  • Diode to ground: 0.015
  • Voltage with power applied: 1.150 V
  • Resistance: 7.690R

To check it: power off and unplug, then diode-mode from the rail to ground and compare with 0.015. Then power up into S0 and measure the voltage against 1.150 V.

A diode or resistance far below known-good suggests a short or leaky load on the rail; far above suggests an open feed or missing enable. No known-good waveform or current reading here.

PPVCORE_S0_GFX_PH10.0021.1002.510R
AI: what PPVCORE_S0_GFX_PH1 is and how to check it

PPVCORE_S0_GFX_PH1 is a graphics core power rail, one phase of the GPU VCORE supply; the S0 in the name means it belongs to the running (S0) state. Known-good readings from the archive: diode 0.002, voltage 1.100 V, resistance 2.510R (community values, a guide only). Check it unpowered in diode mode to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.002 or a voltage well off 1.100 V usually points to a short or a fault in that phase's supply, but one reading alone doesn't confirm a bad part.

PPVCORE_S0_GFX_PH20.0021.1002.510R
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 is a GPU core power rail, one phase of the graphics VCORE supply; the S0 in the name means it belongs to the running state. Known-good readings here are diode 0.002, voltage 1.100 V and resistance 2.510R; treat these as a community guide, and note there is no known-good condition recorded for them. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far above 0.002 or a voltage well off 1.100 V usually points to a problem in that phase's supply or its load, but one reading alone doesn't confirm a bad part.

PPVCORE_S0_GPU0.0021.1002.510R
AI: what PPVCORE_S0_GPU is and how to check it

PPVCORE_S0_GPU is the GPU core power rail; the S0 in the name means it belongs to the running (S0) state, and the GPU part of the name says it feeds the graphics processor. Known-good community readings are diode 0.002, voltage 1.100 V and resistance 2.510R — treat these as a guide, since they vary with board state. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied and the board in S0. A reading far from these usually points to a short or open on the rail or its supply, not proof of a bad part; no known-good reading of another kind is listed here.

PPVDDCI_S0_GPU0.0240.900–
AI: what PPVDDCI_S0_GPU is and how to check it

PPVDDCI_S0_GPU — reference note

  • This is a GPU supply rail, from the name: VDDCI is the GPU's I/O/interface supply, and S0 means it is up in the running state. It sits in the S0 group alongside PPVCORE_S0_GPU and PP1V8_S0_GPU.
  • Known-good readings from the archive: diode 0.024 to ground, and 0.900 V with the board powered in S0. These are community figures and a guide only, not a guaranteed value.
  • To check it: power off and unplug, then diode-mode from the rail to ground. Power up and confirm the rail comes up in S0, after the GPU core rail and its PGOOD signals.
  • No resistance reading is recorded for this rail. A diode reading far from 0.024 usually points to a short or a leaky part on the rail, but confirm with a second reading before condemning anything.
PPVIN_S0_CPUVR_VIN0.22––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN — reference note

  • What it is: the input supply to the CPU voltage regulator, from the name: CPUVR = CPU VR, VIN = its input rail. The S0 in the name places it in the running state, so it should be present once the board is fully on.
  • Known-good reading: diode mode to ground 0.22 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: power off and measure diode mode from the rail to ground first, then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; a missing voltage with a normal diode reading points upstream, at whatever feeds the rail. Confirm with a second measurement before replacing anything.
PPVIN_S0_GFXIMVP_VIN0.359––
AI: what PPVIN_S0_GFXIMVP_VIN is and how to check it

PPVIN_S0_GFXIMVP_VIN — reference note

  • This is the input supply to the GPU's IMVP (GPU core) regulator. The name says it: VIN = input, GFXIMVP = GPU IMVP controller, S0 = present while the board is running.
  • Known-good reading from the archive: diode mode to ground 0.359. That is the only reading recorded for this net; there is no known-good voltage here.
  • Check it with the board unpowered, in diode mode from the net to ground, then power up and measure the DC voltage on the same net.
  • A diode reading far from 0.359 suggests a short or an open on that input path rather than the rail itself; a missing voltage with a good diode reading points upstream, to the feed that supplies this input.
PPVIN_S0GPU_1V8_RC0.378––
AI: what PPVIN_S0GPU_1V8_RC is and how to check it

PPVIN_S0GPU_1V8_RC — reference note

  • From its name: an input rail (PPVIN) feeding the GPU 1.8 V supply, in the S0 (running) state; the RC suffix likely marks a resistor/capacitor-fed or filtered feed, which is general naming, not from this board's data.
  • Known-good reading here: diode 0.378 in diode mode. No known-good voltage reading is recorded for this net.
  • Check it with the board unpowered (battery and charger off) in diode mode, red probe on ground, black on the net, and compare with 0.378; then power up into S0 and measure the DC voltage at the same point.
  • A diode reading far below 0.378 usually suggests a short or a leaky load on the rail; far above suggests an open feed or a missing connection. One reading alone doesn't condemn a part, so confirm with the voltage measurement and a second point on the same net.
PPVIN_S0SW_LCDBKLT0.86913.100–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail, an S0 (running) supply — that's from the name. Known-good readings here: diode 0.869 to ground and 13.100 V with the board running; no known-good resistance is listed.

  • Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far below 0.869 suggests a short or leaky load on the rail; a voltage well off 13.100 V points to the supply feeding it or its enable, not necessarily the rail itself.
  • One reading alone doesn't condemn a part; compare with the related PPVIN_S0SW_LCDBKLT_FET and PPVIN_S0SW_LCDBKLT_R nets.
PPVIN_S0SW_LCDBKLT_FET0.36613.100–
AI: what PPVIN_S0SW_LCDBKLT_FET is and how to check it

PPVIN_S0SW_LCDBKLT_FET is the switched input feed for the LCD backlight circuit; the name says it's an S0 (running-state) rail, and the FET suffix means it sits after a switching FET. Known-good readings here are diode 0.366 to ground and 13.100 V with the board powered in S0. Check it with the board off and unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.366 suggests a short or leaky part on that feed; a low or missing voltage points to the upstream backlight enable or the FET not switching. No known-good resistance reading is recorded for this rail.

PPVIN_S0SW_LCDBKLT_R0.36613.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it
  • What it is: PPVIN_S0SW_LCDBKLT_R is the input supply for the LCD backlight switch circuit, from its name: PPVIN (input), S0SW (S0 running-state switch), LCDBKLT (LCD backlight). It sits in the S0 "running" stage.
  • Known-good readings (community guide): diode 0.366 to ground, voltage 13.100 with power applied. No known-good resistance reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; wrong voltage with power on points to the upstream switch or supply feeding it. Confirm with a second measurement before replacing anything.
PPVOUT_S0_LCDBKLT1.20459.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight output rail; the S0 in the name marks it as a running-state rail. Known-good readings here are diode 1.204 and voltage 59.000, both community values and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 1.204 suggests a short or leaky load on the backlight output, while a voltage far from 59.000 with a normal diode reading points to the backlight driver or its enable, not a short. No known-good resistance reading is available for this rail.

Repair notes

Rails

Brute force rails

SUSpend ISNS_1V8_SUS_N ISNS_1V8_SUS_P PM_CLK32K_SUSCLK_R PM_SLP_SUS_L PP1V0_SUS PP1V8_SUS PP1V8_SUS_REG_R PP1V_SUSSW_PCH_VCCAMPHYPLL_F PP1V_SUS_PCH_VCCCLK5_F PP1V_SUS_PCH_VCCHDAPLL_F PP1V_SUS_PCH_VCCUSB2HDAPLL_F PP3V3_SUS PPVIN_SUS_VR5_R SMC_PCH_SUSACK_L SMC_PCH_SUSWARN_L S5 DBGLED_S5 DCIN_S5_VSENSE PM_SLP_S5_L PP1V2_S5_SMC_VDDC PP1V_S5_PCH_DCPDSW PP3V0_S5_AVREF_SMC PP3V3_S5 PP3V3_S5_POLARIS PP3V3_S5_SMC_VDDA PP3V3_S5_T139 PP3V3_S5_TBT_T_SW PP3V3_S5_TBT_X_SW PP5V_S5 S4 DBGLED_S4 DBGLED_S4_D PM_SLP_S4_L PP1V8_S4 PP3V3_S4 PP3V3_S4SW_SNS PP3V3_S4SW_SNS_FET_R PP3V3_S4_BT PP3V3_S4_MESA_SW PP3V3_S4_SOC_PMU PP3V3_S4_T151 PP3V3_S4_TPAD PP3V3_S4_WLAN PP3V3_S4_WLAN_SW PP5V_S4 PP5V_S4_ISNS_D PP5V_S4_TPAD_CONN PP5V_S4_T_USBC PP5V_S4_X_USBC PPBUS_S4_HS_TPAD PPVIN_S4_TPAD_FUSE SMBUS_SMC_2_S4_SCL SMBUS_SMC_2_S4_SDA SMC_PME_S4_DARK_L SMC_PME_S4_WAKE_L S3 DBGLED_S3_D GMUX_SLP_S3_BUF_L PM_SLP_S3_L PP0V6_S3_MEM_VREFCA_A PP0V6_S3_MEM_VREFDQ_A PP0V6_S3_MEM_VREFDQ_B PP1V0_S3 PP1V2_S3 PP1V2_S3_CPUDDR PP1V2_S3_REG_R PP1V8_S3 PP1V8_S3_MEM PP3V3_S3_DPMUX_UC_R SOC_S2R_ACK_L S0 AP_S0IX_WAKE_L AP_S0IX_WAKE_SEL DBGLED_S0 DBGLED_S0I3 DBGLED_S0I3_D DBGLED_S0_D P3V3_S0GPU_PGOOD P5_S0GPU_PGOOD PBUS_S0_VSENSE PBUS_S0_VSENSE_IN PM_SLP_S0S3_L PM_SLP_S0_L PP0V6_S0_DDRVTT PP1V0_S0SW PP1V2_S0SW PP1V5R1V35_S0_GPU_IC PP1V5R1V35_S0_GPU_MEM PP1V8_S0 PP1V8_S0SW_DFR PP1V8_S0_GPU PP1V8_S0_GPU_LC_IC PP1V8_S0_LDO_AUD PP1V8_S0_PCH_VCCHDA_F PP3V3_S0 PP3V3_S0SW_DFR PP3V3_S0SW_LCD PP3V3_S0SW_LCD_R PP3V3_S0_AUD_F PP3V3_S0_CARBON_R PP3V3_S0_CPUTHMSNS_R PP3V3_S0_DPMUX_UC_R PP3V3_S0_GPU PP3V3_S0_GPUTHMSNS_R PP3V3_S0_LEFT PP3V3_S0_TBTTHMSNS_T_R PP3V3_S0_TBTTHMSNS_X_R PP3V3_TBT_T_S0 PP3V3_TBT_X_S0 PP5V_S0 PP5V_S0GPU_P1V35_GPU PP5V_S0SW_LCD PP5V_S0_ALSCAM_F PP5V_S0_BKLT_A PP5V_S0_BKLT_D PP5V_S0_FAN_CONN PP5V_S0_GFXIMVP_VDD PP5V_S0_GFXIMVP_VDDP PP5V_S0_GPUFET PP5V_S0_GPU_OPAMP PP5V_S0_KBD PP5V_S0_T139 PPVCCGT_S0_CPU PPVCCIO_S0_CPU PPVCCSA_S0_CPU PPVCC_S0_CPU PPVCORE_S0_GFX_PH1 PPVCORE_S0_GFX_PH1 PPVCORE_S0_GFX_PH2 PPVCORE_S0_GFX_PH2 PPVCORE_S0_GPU PPVDDCI_S0_GPU PPVIN_S0GPU_1V8_RC PPVIN_S0SW_LCDBKLT PPVIN_S0SW_LCDBKLT_FET PPVIN_S0SW_LCDBKLT_R PPVIN_S0_CPUVR_VIN PPVIN_S0_GFXIMVP_VIN PPVOUT_S0_LCDBKLT SMBUS_SMC_0_S0_SCL SMBUS_SMC_0_S0_SDA SMBUS_SMC_1_S0_SCL SMBUS_SMC_1_S0_SDA

Startup

CD3215 5V to 20V

Power getting to the CD3215... 5V on PP20V_USBC_XA_VBUS at F3000 pin 1 Basic CD3215 voltages + LDOs... 3V3 on PP3V3_UPC_XA_LDO at C3108 pin 1 1V8 on PP1V8_UPC_XA_LDOA at C3106 pin 1 1V8 on PP1V8_UPC_XA_LDOD at C3105 pin 1 1V1 on PP1V1_UPC_XA_LDO_BMC at C3104 pin 1 Open Q3100 so power goes through to PPDCIN_G3H... >5V on UPC_XA_GATE1 at Q3100 pin 1 >5V on UPC_XA_GATE2 at Q3100 pin 4 5V on PPDCIN_G3H at CC773 pin 1 Power to the ISL U7000 ... (in) 5V on TBA_VDDA at C7075 pin 1 (out) >=3V3 on PM_EN_P3V3_G3H at R6921 pin 1 Getting PP3V3_G3H ... 3V3 on PP3V3_G3H at L6900 pin 1 SMC rails... 1V2 on PP1V2_S5_SMC_VDDC at C5012 pin 1 3V0 on PP3V0_S5_AVREF_SMC at C5020 pin 1 ~3V3 on [n:SMBUS_SMC_4_G3H_SCL at R5321 pin 2 (0V66 DM) ~3V3 on [n:SMBUS_SMC_4_G3H_SDA at R5320 pin 2 (0V66 DM) USBC CC1/2... 0V8 on USB_XA_CC1 at C3113 pin 1 0V8 on USB_XA_CC2 at C3114 pin 1 20V switch over... 20V on PP20V_USBC_XA_VBUS at F3000 pin 1 >20V on UPC_XA_GATE1 at Q3100 pin 1 >20V on UPC_XA_GATE2 at Q3100 pin 4 20V on PPDCIN_G3H at CC773 pin 1 Final steps... 5V on TBA_AUX_DET at C7016 pin 1 3V3 on SMC_RST_L at R7090 pin 1 MOSFETS Q7030 and Q7040 should now be open and U7000 should be generating PPBUS_G3H

CD3215 LDOs

U3100 5V on PP20V_USBC_XA_VBUS at F3000 pin 1 3V3 on PP3V3_UPC_XA_LDO at C3108 pin 1 1V8 on PP1V8_UPC_XA_LDOA at C3106 pin 1 1V8 on PP1V8_UPC_XA_LDOD at C3105 pin 1 1V1 on PP1V1_UPC_XA_LDO_BMC at C3104 pin 1 U3200 5V on PP20V_USBC_XB_VBUS at F3001 pin 1 3V3 on PP3V3_UPC_XB_LDO at C3208 pin 1 1V8 on PP1V8_UPC_XB_LDOA at C3206 pin 1 1V8 on PP1V8_UPC_XB_LDOD at C3205 pin 1 1V1 on PP1V1_UPC_XB_LDO_BMC at C3204 pin 1 UB300 5V on PP20V_USBC_TA_VBUS at FB200 pin 1 3V3 on PP3V3_UPC_TA_LDO at CB308 pin 1 1V8 on PP1V8_UPC_TA_LDOA at CB306 pin 1 1V8 on PP1V8_UPC_TA_LDOD at CB305 pin 1 1V1 on PP1V1_UPC_TA_LDO_BMC at CB304 pin 1 UB400 5V on PP20V_USBC_TB_VBUS at FB201 pin 1 3V3 on PP3V3_UPC_TB_LDO at CB408 pin 1 1V8 on PP1V8_UPC_TB_LDOA at CB406 pin 1 1V8 on PP1V8_UPC_TB_LDOD at CB405 pin 1 1V1 on PP1V1_UPC_TB_LDO_BMC at CB404 pin 1

Every net with a reading

NetDiodeVoltageResistance
5VS4_VFB1_RR0.630––
50_0_ANTOL––
50_1_ANTOL––
50_2_ANTOL––
8409_ASP1_LRCLK0.365––
8409_ASP1_LRCLK_R0.360––
8409_ASP1_SCLK0.366––
8409_ASP1_SCLK_R0.367––
8409_ASP1_SDOUT0.365––
8409_ASP1_SDOUT_R0.366––
8409_ASP2_LRCLK0.666––
8409_ASP2_LRCLK_R0.666––
8409_ASP2_SCLK0.550––
8409_ASP2_SCLK_R0.553––
8409_ASP2_SDOUT0.534––
8409_HDA_SDIN0_R0.677––
8409_I2C_SCL0.363––
8409_I2C_SDA0.440––
8409_VA_PLL0.611––
ACT_GND0.00––
ADC1_REFCOMPOL––
AGND_P1V8GPU0.000––
ALL_SYS_PWRGD0.475––
ALS_SCL_I2C_1V80.459––
ALS_SDA_I2C_1V80.457––
ALS_SOC_UART_D2R0.45––
ALS_SOC_UART_R2D0.45––
AP_CLKREQ_L0.589––
AP_CLKREQ_L_R0.765––
AP_DEV_WAKE0.780––
AP_PCIE_WAKE_L0.495––
AP_RESET_CONN_L0.570––
AP_RESET_CONN_R_LOL––
AP_RESET_L0.78––
AP_S0IX_WAKE_L0.52––
AP_S0IX_WAKE_SEL0.724––
AUD_ASP1A_LRCLK0.35––
AUD_ASP1A_SCLK0.35––
AUD_ASP1A_SDOUT0.359––
AUD_ASP1B_LRCLK0.355––
AUD_ASP1B_SCLK0.359––
AUD_ASP1B_SDOUT0.358––
AUD_ASP2_LRCLK0.627––
AUD_ASP2_SCLK0.510––
AUD_ASP2_SDIN0.665––
AUD_ASP2_SDOUT0.487––
AUD_CODEC_INT_L0.705––
AUD_CODEC_RESET_L0.715––
AUD_CODEC_WAKE_L0.713––
AUD_CONN_HP_LEFT0.566––
AUD_CONN_HP_RIGHT0.630––
AUD_CONN_HP_SENSE_LOL––
AUD_CONN_HP_SENSE_ROL––
AUD_CONN_RING20.000––
AUD_CONN_RING2_XW0.625––
AUD_CONN_SLEEVE0.000––
AUD_CONN_SLEEVE_XW0.631––
AUD_CONN_TIP_SENSEOL––
AUD_HP_PORT_CH_GND0.000––
AUD_HP_PORT_L0.670––
AUD_HP_PORT_R0.600––
AUD_HP_PORT_US_GND0.000––
AUD_HP_SENSE_LOL––
AUD_HP_SENSE_ROL––
AUD_HS_MIC_N0.630––
AUD_HS_MIC_P0.630––
AUD_I2C_1A_SCL0.34––
AUD_I2C_1A_SDA0.42––
AUD_I2C_1B_SCL0.354––
AUD_I2C_1B_SDA0.429––
AUD_PWR_EN0.531––
AUD_RING_SENSE0.000––
AUD_SPI_CLK0.780––
AUD_SPI_CS_L0.785––
AUD_SPI_MISO0.785––
AUD_SPI_MOSI0.768––
AUD_SPKRAMP_INT_L0.39––
AUD_SPKRAMP_RESET_L0.34––
AUD_TIP_SENSEOL––
BB_FORCE_PWM0.540––
BKLT_EN_R0.536––
BKLT_PWM_KEYB0.545––
BKLT_PWM_MLB2TCON0.63––
BKLT_PWM_TCON2MLB0.75––
BKLT_SCL0.537––
BKLT_SD0.593––
BKLT_SDA0.539––
BKLT_SENSE_OUT0.726––
BMON_IOUT_DOL––
BT_I2S_CLK0.610––
BT_I2S_CLK_R0.550––
BT_I2S_D2R_R0.600––
BT_I2S_R2D0.745––
BT_I2S_R2D_R0.550––
BT_I2S_SYNC0.612––
BT_I2S_SYNC_R0.550––
BT_LOW_PWR_L0.570––
BT_PWRRST_L0.780––
BT_RX_ACTIVE0.530––
BT_SFLASH_CS_L0.710––
BT_SFLASH_HOLD_L0.704––
BT_SFLASH_WP_L0.711––
BT_SPI2_CSN0.765––
BT_SPI2_MISO0.693––
BT_TIMESTAMP0.738––
BT_UART_CTS_R2D_L0.512––
BT_UART_D2R0.433––
BT_UART_R2D0.510––
BT_UART_RTS_D2R_L0.433––
BUF_EDP_PANEL_PWR_EN0.718––
BUF_SMC_RESET_L0.696––
CAMERA_CLKREQ_L0.780––
CAMERA_PWR_EN0.790––
CARBON_CSOL––
CARBON_DENOL––
CARBON_SA0OL––
CARBON_SCL_ROL––
CARBON_SDA_ROL––
CHGR_AMON0.61––
CHGR_BMON0.620––
COMP_A_CPUCORE0.61––
COMP_A_CPUCORE_LOL––
COMP_B_CPUGT0.61––
COMP_B_CPUGT_LOL––
COMP_C_CPUSA0.61––
COMP_C_CPUSA_LOL––
CORE_ISUMN_R1.007––
CORE2_5G_CTL2_WLAN_JTAG_TDO0.600––
CPU_CATERR_L0.246––
CPU_CFG_RCOMP0.052––
CPU_CFG<0>0.29––
CPU_CFG<1>0.29––
CPU_CFG<2>0.298––
CPU_CFG<3>0.300––
CPU_CFG<4>0.280––
CPU_CFG<5>0.270––
CPU_CFG<6>0.280––
CPU_CFG<7>0.280––
CPU_CFG<8>0.29––
CPU_CFG<9>0.29––
CPU_CFG<10>0.29––
CPU_CFG<11>0.29––
CPU_CFG<12>0.29––
CPU_CFG<16>0.29––
CPU_CFG<17>0.29––
CPU_CFG<18>0.29––
CPU_CFG<19>0.29––
CPU_DC_B2_C1OL––
CPU_DC_B38_C38OL––
CPU_DC_BR1_BR20.360––
CPU_DC_BR2_BR1OL––
CPU_DC_BR38_BT360.001––
CPU_DC_BT36_BR380.001––
CPU_DC_C1_B2OL––
CPU_DC_C38_B38OL––
CPU_DIMM_VREFCA0.695––
CPU_DIMMA_VREFDQ0.760––
CPU_DIMMB_VREFDQ0.760––
CPU_EDP_RCOMP0.077––
CPU_EOPIO_RCOMP0.001––
CPU_OPC_OPIO_RCOMP0.001––
CPU_OPC_OPIO_RCOMP_ED20.001––
CPU_PCH_PM_DOWN0.310––
CPU_PCH_PM_DOWN_R0.300––
CPU_PCH_TRIGGER0.330––
CPU_PCH_TRIGGER_R0.300––
CPU_PECI0.339––
CPU_PECI_R0.318––
CPU_PEG_RCOMP0.075––
CPU_PROCHOT_L0.510––
CPU_PROCHOT_R_L0.300––
CPU_PWRGD0.445––
CPU_RESET_L0.449––
CPU_SM_RCOMP<0>0.200––
CPU_SM_RCOMP<1>0.130––
CPU_SM_RCOMP<2>0.175––
CPU_VCCGTSENSE_N0.003––
CPU_VCCGTSENSE_P0.006––
CPU_VCCIOSENSE_N0.005––
CPU_VCCIOSENSE_P0.047––
CPU_VCCSASENSE_N0.003––
CPU_VCCSASENSE_P0.017––
CPU_VCCSENSE_N0.003––
CPU_VCCSENSE_P0.005––
CPU_VCCST_PWRGD0.446––
CPU_VIDALERT_L0.286––
CPU_VIDALERT_R_L0.507––
CPU_VIDSCLK0.243––
CPU_VIDSCLK_R0.241––
CPU_VIDSOUT0.244––
CPU_VIDSOUT_R0.244––
CPU_VR_EN_R0.45––
CPUCORE_BOOT10.598––
CPUCORE_BOOT20.598––
CPUCORE_BOOT30.597––
CPUCORE_BP10.599––
CPUCORE_BP20.600––
CPUCORE_BP30.597––
CPUCORE_ISEN10.61––
CPUCORE_ISEN20.61––
CPUCORE_ISEN30.61––
CPUCORE_ISNS1_N0.0031.5001.520R
CPUCORE_ISNS1_P0.0031.5001.520R
CPUCORE_ISNS2_N0.0031.500–
CPUCORE_ISNS2_P0.0031.500–
CPUCORE_ISNS3_N0.0031.5001.520R
CPUCORE_ISNS3_P0.0031.5001.520R
CPUCORE_ISUMN0.003––
CPUCORE_ISUMN_R0.31––
CPUCORE_ISUMP0.28––
CPUCORE_PHASE10.003––
CPUCORE_PHASE20.003––
CPUCORE_PHASE30.004––
CPUCORE_PROCHOT_R_L0.50––
CPUCORE_PSYS0.61––
CPUCORE_PWM10.60––
CPUCORE_PWM20.60––
CPUCORE_PWM30.60––
CPUCORE_SW10.0031.5001.52R
CPUCORE_SW1_SNUBOL––
CPUCORE_SW20.0031.5001.52R
CPUCORE_SW2_SNUBOL––
CPUCORE_SW30.0031.5001.52R
CPUCORE_VIDALERT_R_L0.24––
CPUCORE_VIDSCLK_R0.26––
CPUCORE_VIDSOUT_R0.23––
CPUGT_BOOT10.604––
CPUGT_BOOT20.599––
CPUGT_BP10.604––
CPUGT_BP20.600––
CPUGT_ISEN10.61––
CPUGT_ISEN20.61––
CPUGT_ISNS_R_NOL––
CPUGT_ISNS_R_POL––
CPUGT_ISNS1_N0.0051.500–
CPUGT_ISNS1_P0.0051.500–
CPUGT_ISNS2_N0.0051.5002.600R
CPUGT_ISNS2_P0.0051.5002.600R
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN0.006––
CPUGT_ISUMN_R0.37––
CPUGT_ISUMP0.42––
CPUGT_PHASE10.000––
CPUGT_PHASE20.005––
CPUGT_SW10.0051.5002.60R
CPUGT_SW1_SNUBOL––
CPUGT_SW20.0051.5002.60R
CPUGT_SW2_SNUBOL––
CPUGTVSENSE_IN0.000––
CPUHI_COMP_FBOL––
CPUHI_COMP_OUTOL––
CPUHI_COMP_VREFOL––
CPUHI_IOUT0.707––
CPUHI_IOUT_ROL––
CPUSA_BOOTSA0.600––
CPUSA_BPSA0.600––
CPUSA_FCCM0.611––
CPUSA_ISNS_N0.0151.1507.690R
CPUSA_ISNS_P0.0151.1507.690R
CPUSA_ISUMN0.016––
CPUSA_ISUMN_R0.42––
CPUSA_ISUMP0.55––
CPUSA_PHASESA0.011––
CPUSA_SW_SNUBOL––
CPUSAVSENSE_IN0.022––
CPUTHMSNS_ADDR_SEL0.628––
CPUTHMSNS_ALERT_L0.57––
CPUTHMSNS_D1_N0.62––
CPUTHMSNS_D1_P0.62––
CPUTHMSNS_D2_N0.639––
CPUTHMSNS_D2_P0.640––
CPUTHMSNS_D3_N0.637––
CPUTHMSNS_D3_P0.639––
CPUTHMSNS_FILTER0.428––
CPUTHMSNS_THM_L0.51––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS_R_NOL––
CPUVR_ISNS_R_POL––
CPUVR_ISUM_IOUTOL––
CPUVR_PGOOD0.50––
CPUVR_SWSA0.0151.1507.69R
CPUVSENSE_IN0.005––
DBGLED_GPUOL––
DBGLED_GPU_DOL––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S0I3OL––
DBGLED_S0I3_DOL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DBGLED_S5OL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.52––
DDR0_PAR0.288––
DDR1_PAR0.011––
DEBUGUART_SEL_SOC0.791––
DFR_CLKIN_RESET_L0.47––
DFR_DISP_INT0.487––
DFR_DISP_PWR_EN0.51––
DFR_DISP_RESET_L0.710––
DFR_DISP_RST_L0.470––
DFR_DISP_SMC_RST_L0.52––
DFR_DISP_TE0.490––
DFR_DISP_VSYNC0.47––
DFR_TOUCH_GPIO20.47––
DFR_TOUCH_INT_L0.47––
DFR_TOUCH_LID0.420––
DFR_TOUCH_PANEL_DETECT0.46––
DFR_TOUCH_RESET_L0.46––
DFR_TOUCH_ROM_I2C_SCL0.46––
DFR_TOUCH_ROM_I2C_SDA0.46––
DFR_TOUCH_ROM_WC0.46––
DFR_TOUCH_SPI_CLK0.470––
DFR_TOUCH_SPI_CLK_R0.46––
DFR_TOUCH_SPI_CS_L0.46––
DFR_TOUCH_SPI_MISO0.482––
DFR_TOUCH_SPI_MISO_R0.46––
DFR_TOUCH_SPI_MOSI0.470––
DFR_TOUCH_SPI_MOSI_R0.46––
DFRDRV_I2C_SCL0.490––
DFRDRV_I2C_SDA0.485––
DFU_SPI_STATUS0.486––
DFU_STATUS0.486––
DMIC1_CLK0.794––
DMIC1_DATA0.761––
DMIC2_CLK0.794––
DMIC2_DATA0.757––
DP_INT_EG_HPD0.361––
DP_INT_HPD0.612––
DP_INT_HPD_R0.630––
DP_INT_IG_HPD0.550––
DP_T_SNK_RBIAS0.775––
DP_T_SNK0_DDC_CLK0.607––
DP_T_SNK0_DDC_DATA0.600––
DP_T_SNK0_HPD0.580––
DP_T_SNK0_HPD_EG0.376––
DP_T_SNK0_HPD_IG0.587––
DP_T_SNK1_DDC_CLK0.605––
DP_T_SNK1_DDC_DATA0.590––
DP_T_SNK1_HPD0.580––
DP_T_SNK1_HPD_EG0.377––
DP_T_SNK1_HPD_IG0.567––
DP_T_SRC_HPD0.607––
DP_T_SRC_RBIAS0.790––
DP_TA_AUXCH_C_N0.396––
DP_TA_AUXCH_C_P0.420––
DP_TA_AUXCH_N0.813––
DP_TA_AUXCH_P0.814––
DP_TA_HPD0.588––
DP_TB_AUXCH_C_N0.400––
DP_TB_AUXCH_C_P0.429––
DP_TB_AUXCH_N0.812––
DP_TB_AUXCH_P0.815––
DP_TB_HPD0.607––
DP_X_SNK_RBIAS0.778––
DP_X_SNK0_DDC_CLK0.61––
DP_X_SNK0_DDC_DATA0.606––
DP_X_SNK0_HPD0.58––
DP_X_SNK0_HPD_EG0.377––
DP_X_SNK0_HPD_IG0.577––
DP_X_SNK1_DDC_CLK0.61––
DP_X_SNK1_DDC_DATA0.608––
DP_X_SNK1_HPD0.58––
DP_X_SNK1_HPD_EG0.378––
DP_X_SNK1_HPD_IG0.550––
DP_X_SRC_HPD0.606––
DP_X_SRC_RBIAS0.796––
DP_XA_AUXCH_C_N0.370––
DP_XA_AUXCH_C_P0.400––
DP_XA_AUXCH_N0.809––
DP_XA_AUXCH_P0.810––
DP_XA_HPD0.60––
DP_XB_AUXCH_C_N0.370––
DP_XB_AUXCH_C_P0.370––
DP_XB_AUXCH_N0.807––
DP_XB_AUXCH_P0.808––
DP_XB_HPD0.570––
DPMUX_HPD_PDOL––
DPMUX_LRESET_L0.583––
DPMUX_UC_CLK32K0.644––
DPMUX_UC_EXTAL0.623––
DPMUX_UC_EXTAL_ROL––
DPMUX_UC_IRQ0.611––
DPMUX_UC_MD10.609––
DPMUX_UC_MD20.521––
DPMUX_UC_MD2_R0.521––
DPMUX_UC_MDCKN0.622––
DPMUX_UC_PECI0.725––
DPMUX_UC_PEVREF0.450––
DPMUX_UC_RESET_L0.520––
DPMUX_UC_RX0.595––
DPMUX_UC_TCK0.637––
DPMUX_UC_TDI0.635––
DPMUX_UC_TDO0.638––
DPMUX_UC_TMS0.633––
DPMUX_UC_TRST_L0.638––
DPMUX_UC_TX0.590––
DPMUX_UC_VCL0.469––
DPMUX_UC_XTAL0.622––
DPMUX_UC_XTAL_ROL––
EADC1_LCDBKLT_ISENSEOL––
EADC1_OTHER5V_HI_ISENSEOL––
EADC1_PP3V3S4_WLAN_ISENSEOL––
EADC1_PP5V_T139_ISENSEOL––
EADC1_TBT_T_ISENSEOL––
EADC1_TBT_X_ISENSEOL––
EDP_AUXCH_C_N0.44––
EDP_AUXCH_C_P0.44––
EDP_BKLT_EN0.52––
EDP_IG_BKLT_EN0.640––
EDP_IG_PANEL_PWR_EN0.635––
EDP_INT_ML_N<0>0.38––
EDP_INT_ML_N<1>0.38––
EDP_INT_ML_N<2>0.38––
EDP_INT_ML_N<3>0.38––
EDP_INT_ML_P<0>0.38––
EDP_INT_ML_P<1>0.38––
EDP_INT_ML_P<2>0.38––
EDP_INT_ML_P<3>0.38––
EDP_PANEL_PWR_EN0.563––
EG_BKLT_EN0.377––
EG_CLKREQ_OUT_L0.507––
EG_CLKREQ_PU0.540––
EG_CLKREQ_SEL_L0.629––
EG_LCD_PWR_EN0.383––
EG_PEG_CLK100M_N0.373––
EG_PEG_CLK100M_P0.380––
EG_RAIL1_EN0.552––
EG_RAIL2_EN0.629––
EG_RAIL3_EN0.640––
EG_RAIL4_EN0.570––
EG_RAIL5_EN0.531––
EG_RESET_L0.544––
ENETSD_CLKREQ_L0.780––
FAN_LT_PWM0.886––
FAN_LT_TACHOL––
FAN_RT_PWM0.879––
FAN_RT_TACHOL––
FB_A_CALR0.390––
FB_A_CORE_R1.600––
FB_A_CPUCORE0.59––
FB_A_CPUCORE_RC1.167––
FB_A_MVREFD0.560––
FB_A_RESET_L0.400––
FB_A_RESET_PIN_L0.355––
FB_A_RESET_R_L0.365––
FB_A0_MF0.122––
FB_A0_SEN0.121––
FB_A0_VREFC0.415––
FB_A0_VREFD0.76––
FB_A0_ZQ0.121––
FB_A1_MF0.121––
FB_A1_SEN0.121––
FB_A1_VREFC0.420––
FB_A1_VREFD0.756––
FB_A1_ZQ0.121––
FB_B_CPUGT0.59––
FB_B_CPUGT_RC1.170––
FB_B_GT_R1.600––
FB_B0_MF0.121––
FB_B0_SEN0.121––
FB_B0_VREFC0.420––
FB_B0_VREFD0.763––
FB_B0_ZQ0.122––
FB_B1_MF0.122––
FB_B1_SEN0.121––
FB_B1_VREFC0.420––
FB_B1_VREFD0.760––
FB_B1_ZQ0.121––
FB_C_CPUSA0.59––
FB_C_CPUSA_RC1.168––
FB_C_SA_R1.600––
FB_CORE_R0.005––
FB_GT_R0.006––
FB_SA_R0.014––
FBVDD_ALTVO0.539––
GFX_SELF_THROTTLE0.380––
GFX_SELF_THROTTLE_R0.379––
GFXIMVP_BOOT10.443––
GFXIMVP_BOOT1_R0.466––
GFXIMVP_BOOT20.444––
GFXIMVP_BOOT2_R0.465––
GFXIMVP_ISEN10.596––
GFXIMVP_ISEN20.596––
GFXIMVP_ISNS_NOL––
GFXIMVP_ISNS_R_NOL––
GFXIMVP_ISNS_R_POL––
GFXIMVP_ISNS1_N0.0021.1002.510R
GFXIMVP_ISNS1_P0.0021.1002.510R
GFXIMVP_ISNS2_N0.0021.1002.510R
GFXIMVP_ISNS2_P0.0021.1002.510R
GFXIMVP_ISUM_IOUTOL––
GFXIMVP_ISUMN0.002––
GFXIMVP_ISUMN_R0.510––
GFXIMVP_ISUMP0.470––
GFXIMVP_ISUMP_COL––
GFXIMVP_PHASE10.0021.1002.510R
GFXIMVP_PHASE20.0021.1002.51R
GFXIMVP_Q1S10.002––
GFXIMVP_Q1S20.002––
GMUX_SLP_S3_BUF_L0.520––
GND_5V3V3_AGND0.00––
GPU_ANALOGIO0.715––
GPU_AUD_PORT_CONN<0>0.404––
GPU_AUD_PORT_CONN<1>0.403––
GPU_AUD_PORT_CONN<2>0.404––
GPU_AUD<0>0.372––
GPU_AUD<1>0.370––
GPU_AUX_ZVSS0.152––
GPU_BIF_GEN3_EN_A0.370––
GPU_BP_00.400––
GPU_BP_10.400––
GPU_BRD_CFG<0>0.404––
GPU_BRD_CFG<1>0.404––
GPU_BRD_CFG<2>0.405––
GPU_CLKREQ_L0.445––
GPU_DBG_80.411––
GPU_DBG_90.409––
GPU_DBG_100.410––
GPU_DBG_110.411––
GPU_DIECRACKMON0.001––
GPU_FB_SNS_COMMON_NEG0.001––
GPU_FDO0.370––
GPU_GFX_OVERTEMP0.614––
GPU_GFX_PWR_LEVEL_L0.391––
GPU_GFX_PWR_LEVEL_R_L0.391––
GPU_GPIO_SVC0.420––
GPU_GPIO_SVC_R0.416––
GPU_GPIO_SVD0.415––
GPU_GPIO_SVD_R0.411––
GPU_JTAG_TCK0.378––
GPU_JTAG_TDI0.378––
GPU_JTAG_TDO0.378––
GPU_JTAG_TMS0.376––
GPU_JTAG_TRST_L0.386––
GPU_MPLS_PS_00.410––
GPU_MPLS_PS_10.412––
GPU_MPLS_PS_20.409––
GPU_MPLS_PS_30.411––
GPU_PCIE_ZVSS0.203––
GPU_PLLCHARZ_H0.311––
GPU_PLLCHARZ_L0.320––
GPU_PLLCHARZ_RC_HOL––
GPU_PLLCHARZ_RC_LOL––
GPU_RESET_R_L0.540––
GPU_ROM_CONFIG<0>0.404––
GPU_ROM_CONFIG<1>0.380––
GPU_ROM_CONFIG<2>0.376––
GPU_ROM_CS_LOL––
GPU_ROM_CS_L_R0.370––
GPU_ROM_SCLKOL––
GPU_ROM_SCLK_R0.365––
GPU_ROM_SIOL––
GPU_ROM_SI_R0.371––
GPU_ROM_SO0.370––
GPU_ROM_SO_ROL––
GPU_ROM_WP_LOL––
GPU_SMB_CLK0.449––
GPU_SMB_DAT0.450––
GPU_SMBUS_ADDR<0>0.400––
GPU_SMBUS_ADDR<1>0.405––
GPU_TEST_EN0.802––
GPU_TEST_PG0.785––
GPU_TEST_PG_BACON0.803––
GPU_TX_DEEMPH_EN0.392––
GPU_TX_HALF_SWING0.385––
GPU_VCORE_LOAD0.003––
GPU_VCORE_PCC0.381––
GPU_VCORE_SOURCE0.003––
GPU_VGA_DIS0.374––
GPU_VRAM_STRAP0.377––
GPU_XTAL_OR_CLK_IN0.660––
GPU_XTAL_OUT0.530––
GPU_XTAL_PU_OR_CAP0.604––
GPU_XTAL_PWR_OR_GND0.213––
GPU_XTAL_XTAL_OR_CLK0.690––
GPUCOREVSENSE_IN0.003––
GPUFB_AGND0.000––
GPUFB_BOOT_RC0.584––
GPUFB_CS_N0.0601.500170.000
GPUFB_CS_P0.0701.500170.000
GPUFB_DRVH0.613––
GPUFB_DRVH_R0.550––
GPUFB_DRVL0.445––
GPUFB_FSEL0.540––
GPUFB_GPU_OCSET_R0.070––
GPUFB_GPU_VO_R0.060––
GPUFB_LL0.1721.500170.000
GPUFB_OCSET0.535––
GPUFB_PGOOD0.516––
GPUFB_RTN_DIV0.522––
GPUFB_SENSE_DIV0.523––
GPUFB_SET_R0.537––
GPUFB_SET00.541––
GPUFB_SET10.560––
GPUFB_SREF0.538––
GPUFB_VBST0.560––
GPUFB_VO0.535––
GPUTHMSNS_D1_N0.615––
GPUTHMSNS_D1_P0.649––
GPUTHMSNS_D2_N0.645––
GPUTHMSNS_D2_P0.650––
GPUVCORE_COMP0.582––
GPUVCORE_COMP_COL––
GPUVCORE_EN0.569––
GPUVCORE_FB0.528––
GPUVCORE_FB_ROL––
GPUVCORE_FB20.593––
GPUVCORE_NTC0.605––
GPUVCORE_PGOOD0.545––
GPUVCORE_SENSE_N0.002––
GPUVCORE_SENSE_P0.003––
GPUVCORE_SVC0.604––
GPUVCORE_SVC_R0.420––
GPUVCORE_SVD0.449––
GPUVCORE_SVD_R0.420––
GPUVCORE_SVT0.414––
GPUVCORE_SVT_R0.435––
GPUVCORE_VR_HOT_L0.454––
GPUVDDCIVSENSE_IN0.025––
GT_ISUMN_R1.010––
HALL_SENSOR_LEFT0.47––
HALL_SENSOR_RIGHT0.482––
HDA_BIT_CLK0.749-1.000–
HDA_BIT_CLK_R0.578––
HDA_RST_L0.7481.900–
HDA_RST_R_L0.580––
HDA_SDIN00.561––
HDA_SDOUT0.748––
HDA_SDOUT_R0.740––
HDA_SYNC0.748––
HDA_SYNC_R0.590––
HPWR_EN_L0.61––
HS_MIC_N0.723––
HS_MIC_P0.727––
HS_OTHER3V3_IOUTOL––
HS_OTHER5V_IOUTOL––
I2C_ALS_SCL0.54––
I2C_ALS_SCL_R0.490––
I2C_ALS_SDA0.54––
I2C_ALS_SDA_R0.490––
I2C_BKLT_SCL0.52––
I2C_BKLT_SDA0.52––
I2C_CAM_SCL0.483––
I2C_CAM_SDA0.46––
I2C_DPMUX_UC_SCL0.595––
I2C_DPMUX_UC_SDA0.595––
I2C_GPU_PCC_SCL0.457––
I2C_GPU_PCC_SDA0.457––
I2C_SSD_SCL0.660––
I2C_SSD_SDA0.664––
I2C_TBT_T_SCL–0.600–
I2C_TBT_T_SDA0.601––
I2C_TBT_TA_INT_L0.599––
I2C_TBT_TB_INT_L0.596––
I2C_TBT_X_SCL0.598––
I2C_TBT_X_SDA0.59––
I2C_TBT_XA_INT_L0.60––
I2C_TBT_XB_INT_L0.599––
I2C_UPC_T_SCL20.68––
I2C_UPC_T_SDA20.68––
I2C_UPC_TA_DBG_CTL_SCL0.775––
I2C_UPC_TA_DBG_CTL_SDA0.521––
I2C_UPC_TB_DBG_CTL_SCL0.773––
I2C_UPC_TB_DBG_CTL_SDA0.774––
I2C_UPC_X_SCL20.68––
I2C_UPC_X_SDA20.68––
I2C_UPC_XA_DBG_CTL_SCL0.772––
I2C_UPC_XA_DBG_CTL_SDA0.771––
I2C_UPC_XB_DBG_CTL_SCL0.772––
I2C_UPC_XB_DBG_CTL_SDA0.771––
IAPC_OPA_OUTOL––
IMON_A_CPUCORE0.61––
IMON_B_CPUGT0.61––
IMON_C_CPUSA0.61––
ISNS_1V0_NOL––
ISNS_1V0_POL––
ISNS_1V8_SUS_NOL––
ISNS_1V8_SUS_POL––
ISNS_BT_IOUTOL––
ISNS_BT_NOL––
ISNS_BT_POL––
ISNS_CAMERA_IOUTOL––
ISNS_CAMERA_NOL––
ISNS_CAMERA_POL––
ISNS_CPUDDR_IOUTOL––
ISNS_CPUDDR_NOL––
ISNS_CPUDDR_POL––
ISNS_CPUHIGAIN_N0.362––
ISNS_CPUHIGAIN_OUTOL––
ISNS_CPUHIGAIN_OUT_ROL––
ISNS_CPUHIGAIN_P0.362––
ISNS_CPUHIGAIN_R_N1.350––
ISNS_CPUHIGAIN_R_P0.384––
ISNS_CPUSA_IOUTOL––
ISNS_DDR_IOUTOL––
ISNS_GPU_HS_IOUT0.716––
ISNS_GPU_HS_N0.363––
ISNS_GPU_HS_P0.363––
ISNS_GPU1V8_IOUTOL––
ISNS_GPUFB_IOUTOL––
ISNS_GPUFBIC_IOUTOL––
ISNS_GPUVDDCI_IOUTOL––
ISNS_HS_COMPUTING_N0.36013.100–
ISNS_HS_COMPUTING_P0.36013.100–
ISNS_HS_OTHER3V3_NOL––
ISNS_HS_OTHER3V3_POL––
ISNS_HS_OTHER5V_NOL––
ISNS_HS_OTHER5V_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.36613.100–
ISNS_LCDBKLT_P0.36613.100–
ISNS_LCDPANEL_IOUTOL––
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_LPDDR_IOUTOL––
ISNS_LPDDR_NOL––
ISNS_LPDDR_POL––
ISNS_PP3V3_TPAD_IOUTOL––
ISNS_PP3V3_TPAD_NOL––
ISNS_PP3V3_TPAD_POL––
ISNS_PP3V3S0_IOUTOL––
ISNS_PP3V3S4_WLAN_IOUTOL––
ISNS_PP5V_T139_IOUTOL––
ISNS_PP5V_T139_NOL––
ISNS_PP5V_T139_POL––
ISNS_SSDNAND_IOUTOL––
ISNS_T139_NOL––
ISNS_T139_POL––
ISNS_T151_IOUTOL––
ISNS_T151_NOL––
ISNS_T151_POL––
ISNS_TBT_T_IOUTOL––
ISNS_TBT_T_NOL––
ISNS_TBT_T_POL––
ISNS_TBT_X_IOUTOL––
ISNS_TBT_X_NOL––
ISNS_TBT_X_POL––
ISNS_TPAD_NOL––
ISNS_TPAD_POL––
ISNS_WLAN_NOL––
ISNS_WLAN_POL––
ISNS_WLAN_R_NOL––
ISNS_WLAN_R_POL––
ISNS_X239_INT_IOL––
ISNS_X239_INT_NIOL––
ISNS_X239_IOUTOL––
ISNS_X239_IOUT_BUFOL––
ITP_PMODE0.51––
JTAG_ISP_TCK0.573––
JTAG_ISP_TDI0.574––
JTAG_ISP_TDO0.570––
JTAG_TBT_T_TMS0.609––
JTAG_TBT_TCK0.573––
JTAG_TBT_TDI0.573––
JTAG_TBT_W_TMS0.782––
JTAG_TBT_X_TMS0.605––
KBD_BLC_GSLATOL0.500–
KBD_BLC_GSSCKOL0.400–
KBD_BLC_GSSINOL0.000–
KBD_BLC_GSSOUTOL0.000–
KBD_BLC_XBLANKOL0.000–
KBD_I2C_SCLOL0.200–
KBD_I2C_SDAOL-0.000–
KBD_INT_LOL0.000–
L83_FILTP0.796––
L83_FLYC0.390––
L83_FLYN0.560––
L83_FLYP0.421––
L83_HSBIAS_FILT0.720––
L83_HSBIAS_FILT_REF0.630––
L83_LDO_EN0.524––
L83_SDOUT0.630––
L83_VCP0.397––
L83_VCP_FILTN0.840––
L83_VCP_FILTP0.400––
L83_VL0.395––
L83_VP0.355––
LCD_FSS0.63––
LCD_IRQ_L0.79––
LCD_MUX_EN0.628––
LCD_MUX_SEL0.629––
LCD_PSR_EN0.790––
LCD_PWR_SLEW0.705––
LCD_PWR_SLEW_3V30.638––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.727––
LCDBKLT_FET_DRV0.515––
LCDBKLT_FET_DRV_R0.533––
LCDBKLT_SW0.442––
LCDBKLT_TB_XWR1.20459.000–
LPC_AD_R<0>0.550––
LPC_AD_R<1>0.550––
LPC_AD_R<2>0.550––
LPC_AD_R<3>0.550––
LPC_AD<0>0.582––
LPC_AD<1>0.590––
LPC_AD<2>0.577––
LPC_AD<3>0.589––
LPC_CLK24M_DPMUX_UC0.590––
LPC_CLK24M_DPMUX_UC_R0.599––
LPC_CLK24M_SMC0.733––
LPC_CLK24M_SMC_R0.740––
LPC_CLKRUN_L0.737––
LPC_FRAME_L0.587––
LPC_FRAME_R_L0.560––
LPC_PWRDWN_L0.747––
LPC_SERIRQ0.736––
MEM_A_ALERT0.011––
MEM_B_ALERT0.011––
MEM_VREFCA_A_RC0.026––
MEM_VREFDQ_A_RC0.026––
MEM_VREFDQ_B_RC0.026––
MENU_KEY_LOL––
MESA_BOOST_EN0.525––
MESA_BOOST_EN_CONNOL––
MESA_I2C_SCL0.485––
MESA_I2C_SDA0.484––
MESA_PWR_EN0.477––
MESA_SNSR_INT0.497––
MESA_SNSR_INT_CONNOL––
MESA_SPI_CLK0.470––
MESA_SPI_CLK_CONN0.550––
MESA_SPI_CLK_R0.497––
MESA_SPI_MISO0.500––
MESA_SPI_MISO_CONN0.495––
MESA_SPI_MOSI0.465––
MESA_SPI_MOSI_CONN0.497––
MESA_SPI_MOSI_R0.493––
MIPI_CLK_CONN_N0.52––
MIPI_CLK_CONN_P0.52––
MIPI_DATA_CONN_N0.52––
MIPI_DATA_CONN_P0.52––
MIPIC_CLK_N0.52––
MIPIC_CLK_P0.52––
MIPIC_DATA_N0.52––
MIPIC_DATA_P0.52––
MIPID_CLK_CONN_N0.780––
MIPID_CLK_CONN_P0.780––
MIPID_CLK_N0.780––
MIPID_CLK_P0.780––
MIPID_DATA_CONN_N0.780––
MIPID_DATA_CONN_P0.780––
MIPID_DATA_N0.780––
MIPID_DATA_P0.780––
MLB_BOARD_ID00.727––
MLB_BOARD_ID10.780––
MLB_BOARD_ID20.786––
MLB_BOARD_ID30.785––
MLB_BOARD_ID40.791––
MLB_DEV_L0.570––
MLB_RAMCFG00.791––
MLB_RAMCFG10.743––
MLB_RAMCFG20.792––
MLB_RAMCFG30.744––
MLB_RAMCFG40.724––
MOJAVE_EN_M0.500––
NC0.780––
NTC_A_CPUCORE0.61––
NTC_A_CPUCORE_ROL––
NTC_B_CPUGT0.61––
NTC_B_CPUGT_ROL––
P0V9_TBT_T_SVR_AGND0.000––
P0V9_TBT_X_SVR_AGND0.000––
P1V0_SSD_CORE_SW0.3301.000–
P1V0S0SW_RAMP0.625––
P1V0S3_EN0.569––
P1V0S3_RAMP0.618––
P1V1_SSD_PCIE_SW0.3601.100–
P1V2_DRVH0.758––
P1V2_DRVL0.469––
P1V2_DRVL_R0.469––
P1V2_PHASE0.2351.200–
P1V2_SSD_DRAM_SW0.3101.200–
P1V2_SW0.236––
P1V2_SW_SNUBOL––
P1V2_VBST0.600––
P1V2_VBST_R0.608––
P1V2S0SW_RAMPOL––
P1V2S3_FB_N0.001––
P1V2S3_FB_P0.230––
P1V2S3_FB_R_N0.001––
P1V2S3_FB_R_P0.220––
P1V2S3_ILIM_HS0.484––
P1V5R1V35_GPU_FB_SNS_N0.015––
P1V5R1V35_GPU_FB_SNS_P0.070––
P1V8_SSD_DRAM_SW0.4101.800–
P1V8_SSD_FMC_SW0.3701.800–
P1V8GPU_ENOL––
P1V8GPU_FSW0.212––
P1V8GPU_PGOOD0.528––
P1V8S0_RAMP0.613––
P1V8S3_EN0.492––
P1V8S3_RAMP0.613––
P1V8S3_SW_SNUBOL––
P1V8SUS_FB_N0.100––
P1V8SUS_FB_P0.450––
P1V8SUS_FB_R_N0.001––
P1V8SUS_FB_R_P0.460––
P1V8SUS_FB_RC0.420––
P1V8SUS_IOUTOL––
P1V8SUS_SW0.427––
P1VS0SW_EN_RC0.569––
P1VS4_DRVH0.350––
P1VS4_DRVL0.468––
P1VS4_FB_N0.001––
P1VS4_FB_P0.062––
P1VS4_FB_R_N0.001––
P1VS4_FB_R_P0.052––
P1VS4_ILIM_HS0.46––
P1VS4_PHASE0.0301.000–
P1VS4_SW0.048––
P1VS4_SW_SNUBOL––
P1VS4_VBST0.580––
P1VS4_VBST_R0.600––
P1VSUS_PGOOD0.45––
P3V3_S0GPU_PGOOD0.640––
P3V3_TBT_T_SX_EN0.698––
P3V3_TBT_T_SX_EN_R0.700––
P3V3_TBT_X_SX_EN0.700––
P3V3_TBT_X_SX_EN_R0.640––
P3V3G3H_AGND0.001––
P3V3G3H_BIAS0.561––
P3V3G3H_FB0.590––
P3V3G3H_FB_ROL––
P3V3G3H_FB_RC0.370––
P3V3G3H_LX0.3603.300–
P3V3G3H_VBST_R0.611––
P3V3GPU_EN0.555––
P3V3GPU_RAMP0.612––
P3V3S0_CAP0.567––
P3V3S0SW_RAMP0.600––
P3V3S4_EN_R0.480––
P3V3S5_COMP20.73––
P3V3S5_COMP2_ROL––
P3V3S5_CSN20.3703.300–
P3V3S5_CSP21.20––
P3V3S5_CSP2_R0.3703.300–
P3V3S5_DRVH0.92––
P3V3S5_DRVL0.56––
P3V3S5_EN_RCD0.50––
P3V3S5_EN_RDOL––
P3V3S5_RF0.57––
P3V3S5_SNUBROL––
P3V3S5_SW0.36––
P3V3S5_TG0.935––
P3V3S5_VBST0.62––
P3V3S5_VBST_R0.560––
P3V3S5_VFB20.56––
P3V3S5_VFB2_R0.370––
P3V3S5_VFB2_RR0.390––
P3V3S5_VSW0.3703.300–
P5_S0GPU_PGOOD0.637––
P5VGPU_RAMPOL––
P5VP3V3_SKIPSEL0.47––
P5VP3V3_VREF20.47––
P5VP3V3_VREG30.55––
P5VS0_EN0.452––
P5VS0_EN_RDOL––
P5VS0_FET_RAMP0.616––
P5VS0_TG0.970––
P5VS0_VBST_R0.630––
P5VS4_COMP10.73––
P5VS4_COMP1_ROL––
P5VS4_CSN10.425.000–
P5VS4_CSP10.91––
P5VS4_CSP1_R0.4205.000–
P5VS4_DRVH0.98––
P5VS4_DRVL0.55––
P5VS4_EN_RCD0.48––
P5VS4_EN_RDOL––
P5VS4_PGOOD0.44––
P5VS4_SNUBROL––
P5VS4_SW0.42––
P5VS4_VBST0.62––
P5VS4_VFB10.56––
P5VS4_VFB1_R0.430––
P5VS4_VSW0.4205.000–
P5VUSBCT_AGND0.001––
P5VUSBCT_BOOT_RCOL––
P5VUSBCT_DRVH0.840––
P5VUSBCT_DRVH_R0.840––
P5VUSBCT_DRVL0.450––
P5VUSBCT_FSEL0.546––
P5VUSBCT_LL0.2505.000–
P5VUSBCT_N0.2505.000–
P5VUSBCT_OCSET0.541––
P5VUSBCT_P0.2505.000–
P5VUSBCT_R0.2505.000–
P5VUSBCT_RTN_DIV0.541––
P5VUSBCT_RTN_DIV_R0.001––
P5VUSBCT_SENSE_DIV0.530––
P5VUSBCT_SENSE_DIV_R0.377––
P5VUSBCT_SET_ROL––
P5VUSBCT_SET00.544––
P5VUSBCT_SET10.543––
P5VUSBCT_SREF0.541––
P5VUSBCT_VBST0.610––
P5VUSBCT_VO0.542––
P5VUSBCX_AGND0.000––
P5VUSBCX_BOOT_RC0.590––
P5VUSBCX_DRVH0.590––
P5VUSBCX_DRVH_R0.594––
P5VUSBCX_DRVL0.440––
P5VUSBCX_FSEL0.542––
P5VUSBCX_LL0.2415.000–
P5VUSBCX_N0.241––
P5VUSBCX_OCSET0.534––
P5VUSBCX_P0.241––
P5VUSBCX_R0.2415.000–
P5VUSBCX_RTN_DIV0.530––
P5VUSBCX_RTN_DIV_R0.002––
P5VUSBCX_SENSE_DIV0.538––
P5VUSBCX_SENSE_DIV_R0.241––
P5VUSBCX_SET_ROL––
P5VUSBCX_SET00.540––
P5VUSBCX_SET10.540––
P5VUSBCX_SREF0.530––
P5VUSBCX_VBST0.590––
P5VUSBCX_VO0.534––
P12V_SSD_VPP_SW0.45012.000–
P12V_SSD_VPP_SW_L0.45012.000–
P16V0_AGND0.000––
PANEL_FET_EN_DLY0.697––
PANEL_P3V3_EN0.575––
PANEL_P3V3_EN_D0.753––
PANEL_P5V_EN0.571––
PANEL_P5V_EN_D1.032––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.365––
PBUSVSENS_EN_L0.462––
PBUSVSENS_EN_L_DIVOL––
PCC_COMP_OUT_BASEOL––
PCC_POT_LEVELOL––
PCC_POT_LEVEL_DOL––
PCC_POT_LEVEL_ROL––
PCC_POT_REFOL––
PCC_POT_RHOL––
PCC_POT_RLOL––
PCH_ALS_TO_SOC_UART_TXD0.436––
PCH_BT_ROM_BOOT0.570––
PCH_BT_UART_CTS_L0.476––
PCH_BT_UART_D2R0.465––
PCH_BT_UART_R2D0.433––
PCH_BT_UART_RTS_L0.436––
PCH_CPU_TRIGGER0.518––
PCH_CPU_TRIGGER_R0.495––
PCH_DDPB_CTRLDATA0.770––
PCH_DDPC_CTRLDATA0.770––
PCH_DDPD_CTRLDATA0.770––
PCH_DIFFCLK_BIASREF0.789––
PCH_DISPA_BCLK0.451––
PCH_DISPA_BCLK_R0.460––
PCH_DISPA_SDI0.369––
PCH_DISPA_SDO0.449––
PCH_DISPA_SDO_R0.453––
PCH_INTRUDER_L0.810––
PCH_JTAGX0.057––
PCH_PCIE_RCOMPN0.386––
PCH_PCIE_RCOMPP0.388––
PCH_PECI0.350––
PCH_PROCPWRGD0.480––
PCH_RCIN_L_PU0.786––
PCH_SOC_DBELL_L0.480––
PCH_SOC_DFU_STATUS0.560––
PCH_SOC_FORCE_DFU0.484––
PCH_SOC_WDOG0.561––
PCH_SRTCRST_L0.815––
PCH_STRP_TOPBLK_SWP_L0.590––
PCH_SWD_IO0.670––
PCH_SWD_MUX_SEL0.588––
PCH_TO_SOC_UART_TXD0.465––
PCH_UART2_CTS_L0.570––
PCIE_AP_R2D_C_N0.410––
PCIE_AP_R2D_C_P0.410––
PCIE_AP_R2D_N0.460––
PCIE_AP_R2D_P0.460––
PCIE_CLK100M_SSD_N0.387––
PCIE_CLK100M_SSD_P0.396––
PCIE_SSD_D2R_LB_N<0>OL––
PCIE_SSD_D2R_LB_P<0>OL––
PCIE_SSD_D2R_N<0>0.418––
PCIE_SSD_D2R_N<1>0.427––
PCIE_SSD_D2R_N<2>0.429––
PCIE_SSD_D2R_N<3>0.423––
PCIE_SSD_D2R_P<0>0.415––
PCIE_SSD_D2R_P<1>0.425––
PCIE_SSD_D2R_P<2>0.429––
PCIE_SSD_D2R_P<3>0.420––
PCIE_SSD_R2D_C_N<0>0.390––
PCIE_SSD_R2D_C_N<1>0.406––
PCIE_SSD_R2D_C_N<2>0.402––
PCIE_SSD_R2D_C_N<3>0.401––
PCIE_SSD_R2D_C_P<0>0.390––
PCIE_SSD_R2D_C_P<1>0.403––
PCIE_SSD_R2D_C_P<2>0.401––
PCIE_SSD_R2D_C_P<3>0.400––
PCIE_SSD_R2D_LB_N<0>OL––
PCIE_SSD_R2D_LB_P<0>OL––
PCIE_TBT_T_D2R_C_N<0>0.396––
PCIE_TBT_T_D2R_C_N<1>0.398––
PCIE_TBT_T_D2R_C_N<2>0.398––
PCIE_TBT_T_D2R_C_N<3>0.350––
PCIE_TBT_T_D2R_C_P<1>0.395––
PCIE_TBT_T_D2R_C_P<2>0.396––
PCIE_TBT_T_D2R_C_P<3>0.395––
PCIE_TBT_T_R2D_N<0>0.620––
PCIE_TBT_T_R2D_N<1>0.614––
PCIE_TBT_T_R2D_N<2>0.621––
PCIE_TBT_T_R2D_N<3>0.619––
PCIE_TBT_T_R2D_P<0>0.620––
PCIE_TBT_T_R2D_P<1>0.615––
PCIE_TBT_T_R2D_P<2>0.600––
PCIE_TBT_T_R2D_P<3>0.620––
PCIE_WAKE_L0.500––
PDCINVSENS_EN_L_DIVOL––
PLT_RST_L0.37––
PLT_RST_L_BUF0.637––
PM_ALL_GPU_PGOOD0.519––
PM_BATLOW_L0.560––
PM_CLK32K_SUSCLK_R0.580––
PM_DSW_PWRGD0.751––
PM_EN_P3V3_G3H_R0.614––
PM_EN_PVXS50.50––
PM_MEMVTT_EN0.377––
PM_PCH_PWROK0.447––
PM_PCH_SYS_PWROK0.45––
PM_PWRBTN_L0.721––
PM_RSMRST_LOL––
PM_SLP_S0_L0.471––
PM_SLP_S0S3_L0.510––
PM_SLP_S3_L0.44––
PM_SLP_S4_L0.464––
PM_SLP_S5_L0.48––
PM_SLP_SUS_L0.468––
PM_SYNC0.516––
PM_SYNC_R0.520––
PM_SYSRST_L0.736––
PM_THRMTRIP_L0.274––
PM_THRMTRIP_L_R0.432––
PMIC_EN3V3SW0.545––
PMIC_SHUTDOWN_L0.480––
PMIC_SLAVEADDR0.487––
PMIC_VDCSNS0.000––
PMU_IREF0.537––
PMU_SOC_UWAKE_L0.576––
PMU_SOC_VBUS_DET_L0.570––
PMU_TCAL_GND0.000––
PMU_TCAL_PWR0.538––
PMU_TO_SOC_AWAKE_PWRGD0.453––
PMU_TO_SOC_CLK_32K0.540––
PMU_TO_SOC_RESET_L0.455––
PMU_TO_SOC_SLEEP1_PWRGD0.459––
PMU_TO_SOC_SYS_ALIVE0.487––
PMU_VDD_RTC0.352––
PMU_VPUMP0.530––
PMU_VREF0.532––
PP_STOCKHOLM_TVDD0.351––
PP_STOCKHOLM_VMID0.574––
PP0V6_S0_DDRVTT0.140––
PP0V6_S3_MEM_VREFCA_A0.700––
PP0V6_S3_MEM_VREFDQ_A0.750––
PP0V6_S3_MEM_VREFDQ_B0.750––
PP0V6_SLEEP1_BUCK00.3900.600–
PP0V6_SLEEP2_LDO00.385––
PP0V8_SLEEP1_SW10.218––
PP0V8_SLEEP2_BUCK10.2200.800–
PP0V9_TBT_T_CIO0.370––
PP0V9_TBT_T_DP0.300––
PP0V9_TBT_T_LVR0.256––
PP0V9_TBT_T_PCIE0.288––
PP0V9_TBT_T_SVR0.2450.900–
PP0V9_TBT_T_USB0.380––
PP0V9_TBT_X_CIO0.404––
PP0V9_TBT_X_DP0.32––
PP0V9_TBT_X_LVR0.275––
PP0V9_TBT_X_PCIE0.314––
PP0V9_TBT_X_SVR0.2200.900–
PP0V9_TBT_X_USB0.412––
PP1V_PCH_REG_R0.0301.000–
PP1V_S5_PCH_DCPDSW0.331––
PP1V_SUS_PCH_VCCCLK5_F0.0401.000–
PP1V_SUS_PCH_VCCHDAPLL_F0.0401.000–
PP1V_SUS_PCH_VCCUSB2HDAPLL_F0.0401.000–
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.045––
PP1V0_S0SW0.235––
PP1V0_S30.228––
PP1V0_SSD_CORE0.331.000–
PP1V0_SSD_CORE_L120.2701.000–
PP1V0_SSD_PLL0.2701.000–
PP1V0_SUS0.0401.000–
PP1V1_SLEEP1_PLL_DDR_FILT0.365––
PP1V1_SLEEP1_SW20.321––
PP1V1_SLEEP1_XTAL_FILT0.360––
PP1V1_SLEEP3_BUCK20.2801.100–
PP1V1_SSD_LVDS0.3601.100–
PP1V1_SSD_PCIE0.3601.100–
PP1V1_UPC_TA_LDO_BMC0.523––
PP1V1_UPC_TB_LDO_BMC0.518––
PP1V1_UPC_XA_LDO_BMC0.515––
PP1V1_UPC_XB_LDO_BMC0.516––
PP1V2_S0SW0.239––
PP1V2_S30.2371.200–
PP1V2_S3_CPUDDR0.250––
PP1V2_S3_REG_R0.2351.200–
PP1V2_S5_SMC_VDDC0.517––
PP1V2_SSD_DRAM0.3101.200–
PP1V2_SSD_DRAM_L120.515––
PP1V5R1V35_GPU_REG_R0.1721.500170.000
PP1V5R1V35_S0_GPU_IC0.172––
PP1V5R1V35_S0_GPU_MEM0.1741.500170.000
PP1V8_ALWAYS_LDO90.386––
PP1V8_AWAKE_SW3C0.348––
PP1V8_GPU0.2121.800–
PP1V8_GPU_TSVDD0.212––
PP1V8_MESA0.510––
PP1V8_MESA_CONN0.509––
PP1V8_S00.3401.800–
PP1V8_S0_GPU0.200––
PP1V8_S0_GPU_LC_IC0.200––
PP1V8_S0_LDO_AUD0.396––
PP1V8_S0_PCH_VCCHDA_F0.3401.800–
PP1V8_S0SW_DFR0.531.800–
PP1V8_S30.358––
PP1V8_S3_MEM0.377––
PP1V8_S40.430––
PP1V8_SLEEP2_LPPLL_FILT0.625––
PP1V8_SLEEP2_SW3A0.442––
PP1V8_SLEEP3_BUCK30.4001.800–
PP1V8_SSD_DRAM0.4101.800–
PP1V8_SSD_DRAM_L120.4101.800–
PP1V8_SSD_FMC0.3701.800–
PP1V8_SSD_LVDS0.4101.800–
PP1V8_SSD_OSC0.4101.800–
PP1V8_SSD_PLL00.567––
PP1V8_SSD_PLL01–1.800–
PP1V8_SSD_PLL10.4101.800–
PP1V8_SSD_PLL20.4101.800–
PP1V8_SSD_PLL30.4101.800–
PP1V8_SSD_PLL230.431––
PP1V8_SUS0.4301.800–
PP1V8_SUS_REG_R0.427––
PP1V8_UPC_TA_LDOA0.530––
PP1V8_UPC_TA_LDOD0.488––
PP1V8_UPC_TB_LDOA0.522––
PP1V8_UPC_TB_LDOD0.482––
PP1V8_UPC_XA_LDOA0.525––
PP1V8_UPC_XA_LDOD0.490––
PP1V8_UPC_XB_LDOA0.5281.800–
PP1V8_UPC_XB_LDOD0.4881.800–
PP1V25_PMICVREF0.480––
PP2V5_ADC1_VREFOL––
PP2V9_SYSCLK0.45––
PP3V0_AWAKE_LDO70.530––
PP3V0_G3H0.447––
PP3V0_MESA0.5503.000–
PP3V0_MESA_CONN0.548––
PP3V0_S5_AVREF_SMC0.602––
PP3V3_G3H0.343.300–
PP3V3_G3H_REG_R0.3603.300–
PP3V3_PMICLDO0.417––
PP3V3_S00.32––
PP3V3_S0_AUD_F0.653––
PP3V3_S0_CARBON_ROL––
PP3V3_S0_CPUTHMSNS_R0.402––
PP3V3_S0_DPMUX_UC_R0.358––
PP3V3_S0_GPU0.496––
PP3V3_S0_GPUTHMSNS_R0.382––
PP3V3_S0_LEFT0.339––
PP3V3_S0_TBTTHMSNS_T_R0.401––
PP3V3_S0_TBTTHMSNS_X_R0.385––
PP3V3_S0SW_DFR0.580––
PP3V3_S0SW_LCD0.576––
PP3V3_S0SW_LCD_R0.574––
PP3V3_S3_DPMUX_UC_R0.333––
PP3V3_S40.329––
PP3V3_S4_BT0.330––
PP3V3_S4_MESA_SW0.330––
PP3V3_S4_SOC_PMU0.379––
PP3V3_S4_T1510.331––
PP3V3_S4_TPAD0.34––
PP3V3_S4_WLAN0.330––
PP3V3_S4_WLAN_SW0.310––
PP3V3_S4SW_SNS0.550––
PP3V3_S4SW_SNS_FET_R0.550––
PP3V3_S50.3703.300–
PP3V3_S5_POLARIS0.501––
PP3V3_S5_SMC_VDDA0.360––
PP3V3_S5_T1390.360––
PP3V3_S5_TBT_T_SW0.483––
PP3V3_S5_TBT_X_SW0.483––
PP3V3_SSD_ISNS_R0.408––
PP3V3_SSD_LIM0.4093.300–
PP3V3_SSD_NAND0.3943.300–
PP3V3_SSD_PMIC_AVIN0.408––
PP3V3_SUS0.350––
PP3V3_TBT_T_ANA_PCIE0.512––
PP3V3_TBT_T_ANA_USB20.501––
PP3V3_TBT_T_F0.3503.300–
PP3V3_TBT_T_LC0.529––
PP3V3_TBT_T_S00.3503.300–
PP3V3_TBT_X_ANA_PCIE0.500––
PP3V3_TBT_X_ANA_USB20.507––
PP3V3_TBT_X_F0.3403.300–
PP3V3_TBT_X_LC0.526––
PP3V3_TBT_X_S00.3403.300–
PP3V3_UPC_TA_LDO0.514––
PP3V3_UPC_TB_LDO0.507––
PP3V3_UPC_XA_LDO0.511––
PP3V3_UPC_XB_LDO0.513.300–
PP3V3_VREF_PCCOL––
PP5V_COREVR_VCC0.42––
PP5V_EADC1_AVDDOL––
PP5V_PMICLDO0.460––
PP5V_PMICLDO_R0.450––
PP5V_S00.380––
PP5V_S0_ALSCAM_F0.41––
PP5V_S0_BKLT_A0.382––
PP5V_S0_BKLT_D0.382––
PP5V_S0_FAN_CONN0.386––
PP5V_S0_GFXIMVP_VDD0.378––
PP5V_S0_GFXIMVP_VDDP0.378––
PP5V_S0_GPU_OPAMPOL––
PP5V_S0_GPUFETOL––
PP5V_S0_KBD0.386––
PP5V_S0_T1390.41––
PP5V_S0GPU_P1V35_GPU0.380––
PP5V_S0SW_LCD0.546––
PP5V_S40.425.000–
PP5V_S4_ISNS_DOL––
PP5V_S4_T_USBC0.2505.000–
PP5V_S4_TPAD_CONN0.42––
PP5V_S4_X_USBC0.2415.000–
PP5V_S50.46––
PP5V_USBCT_VCC0.519––
PP5V_USBCX_VCC0.432––
PP5V_VREF_PCCOL––
PP12V_SSD_VPP0.45411.960–
PP16V0_MESA0.653––
PP16V0_MESA_CONN0.654––
PP17V0_MOJAVE_LDOIN0.592––
PP20V_USBC_TA_VBUS0.15520.000–
PP20V_USBC_TA_VBUS_CONN0.15520.000–
PP20V_USBC_TA_VBUS_F0.15520.000–
PP20V_USBC_TB_VBUS0.15520.000–
PP20V_USBC_TB_VBUS_CONN0.15520.000–
PP20V_USBC_TB_VBUS_F0.15520.000–
PP20V_USBC_XA_VBUS0.15520,000–
PP20V_USBC_XA_VBUS_CONN0.15520,000–
PP20V_USBC_XA_VBUS_F0.15520,000–
PP20V_USBC_XB_VBUS0.15520,000–
PP20V_USBC_XB_VBUS_CONN0.15520.000–
PP20V_USBC_XB_VBUS_F0.15520,000–
PPBUS_G3H0.36013.100–
PPBUS_G3H_R0.373––
PPBUS_HS_CPU0.36013.100–
PPBUS_HS_GPU0.36213.100–
PPBUS_HS_OTH3V30.26––
PPBUS_HS_OTH5V0.370––
PPBUS_PMIC0.370––
PPBUS_S4_HS_TPAD0.35712.600–
PPDCIN_G3H0.5520,000–
PPDCIN_G3H_CHGR0.5520,000–
PPDCIN_G3H_CHGR_R0.560––
PPDCPRTC_PCH0.685––
PPSVDD_STOCKHOLM0.348––
PPVBAT_G3H_CHGR_R0.362––
PPVBAT_G3H_CHGR_REG0.36013.100–
PPVBAT_G3H_CONN0.62––
PPVCC_CPU_PH10.0031.5001.520R
PPVCC_CPU_PH20.0031.5001.52R
PPVCC_CPU_PH30.0031.5001.520R
PPVCC_RTC_OSC0.429––
PPVCC_S0_CPU0.0031.5001.520R
PPVCCGT_CPU_PH10.0051.5002.60R
PPVCCGT_CPU_PH20.0051.5002.600R
PPVCCGT_S0_CPU0.0051.5002.600R
PPVCCIO_S0_CPU0.0700.950–
PPVCCSA_CPU_R0.0151.1507.690R
PPVCCSA_S0_CPU0.0151.1507.690R
PPVCORE_S0_GFX_PH10.0021.1002.510R
PPVCORE_S0_GFX_PH20.0021.1002.510R
PPVCORE_S0_GPU0.0021.1002.510R
PPVDD_STOCKHOLM0.314––
PPVDD_U1900_RC0.366––
PPVDDCI_S0_GPU0.0240.900–
PPVIN_G3H_P3V3G3H0.55––
PPVIN_S0_CPUVR_VIN0.22––
PPVIN_S0_GFXIMVP_VIN0.359––
PPVIN_S0GPU_1V8_RC0.378––
PPVIN_S0SW_LCDBKLT0.86913.100–
PPVIN_S0SW_LCDBKLT_FET0.36613.100–
PPVIN_S0SW_LCDBKLT_R0.36613.100–
PPVIN_S4_TPAD_FUSE0.35712.600–
PPVIN_SUS_VR5_R0.370––
PPVIN_SW_LCDBKLT_SW0.87013.100–
PPVIO_32K_B_RC0.425––
PPVIO_VIOE_A_RC0.051––
PPVOUT_S0_LCDBKLT1.20459.000–
PPVRTC_U1900_RC0.360––
PROG1_CPUCOREVR0.61––
PROG2_CPUCOREVR0.61––
PROG3_CPUCOREVR0.61––
PROG4_CPUCOREVR0.61––
PROG5_CPUCOREVR0.61––
PVCCCGT_PH1_AGND0.000––
PVCCCGT_PH1_VCC0.380––
PVCCCGT_PH2_AGND0.000––
PVCCCGT_PH2_VCC0.380––
PVCCCORE_PH1_AGND0.000––
PVCCCORE_PH1_VCC0.381––
PVCCCORE_PH2_AGND0.000––
PVCCCORE_PH2_VCC0.380––
PVCCCORE_PH3_AGND0.000––
PVCCCORE_PH3_VCC0.380––
PVCCCSA_AGND0.000––
PVCCCSA_VCIN0.400––
PVCCIO_DRVH0.581––
PVCCIO_DRVL0.467––
PVCCIO_DRVL_R0.470––
PVCCIO_EN0.430––
PVCCIO_FB_N0.005––
PVCCIO_FB_P0.056––
PVCCIO_ILIM_LS0.480––
PVCCIO_PGOOD0.472––
PVCCIO_PHASE0.0700.950–
PVCCIO_SW0.052––
PVCCIO_SW_SNUBOL––
PVCCIO_VBST0.580––
PVCCIO_VBST_R0.583––
PVCORE_GPU_FB_SNS_N0.001––
PVDDCI_GPU_FB_SNS_N0.020––
PVDDCI_GPU_FB_SNS_P0.040––
PVDDCI_PGOOD0.545––
PVTT_FB0.150––
PVTT_FB_R0.135––
REG_BOOT_GPU_VDDCI0.458––
REG_BOOT_GPU_VDDCI_RC0.462––
REG_FB_P1V8GPU1.397––
REG_GPU_VDDCI_COMP0.576––
REG_GPU_VDDCI_FB0.475––
REG_GPU_VDDCI_FB_ROL––
REG_GPU_VDDCI_FCCM0.593––
REG_GPU_VDDCI_IMON0.605––
REG_GPU_VDDCI_ISEN10.600––
REG_GPU_VDDCI_ISUMN0.588––
REG_GPU_VDDCI_ISUMP0.553––
REG_GPU_VDDCI_VSEN0.002––
REG_GPU_VDDCI_VSEN_COL––
REG_LGATE_GPU_VDDCI0.435––
REG_PHASE_1V8GPU0.2121.800–
REG_PHASE_GPU_VDDCI0.018––
REG_SSTR_P1V8GPU0.740––
REG_UGATE_GPU_VDDCI0.450––
REG_VOS_P1V8GPU0.222––
RTC_RESET_L0.81––
RTN_A_CPUCORE0.00––
RTN_C_CPUSA0.00––
S2R_ACK_L0.475––
S5_PWRGD0.48––
SA_ISUMN_R1.026––
SEP_I2C_SCL0.486––
SEP_I2C_SDA0.486––
SEP_ROM_WC0.750––
SMBUS_PCH_CLK0.754––
SMBUS_PCH_DATA0.755––
SMBUS_SMC_0_S0_SCL0.72––
SMBUS_SMC_0_S0_SDA0.72––
SMBUS_SMC_1_S0_SCL0.550––
SMBUS_SMC_1_S0_SDA0.54––
SMBUS_SMC_2_S4_SCL0.520––
SMBUS_SMC_2_S4_SDA0.513––
SMBUS_SMC_3_SCL0.53––
SMBUS_SMC_3_SDA0.523.300–
SMBUS_SMC_4_G3H_SCL0.688––
SMBUS_SMC_4_G3H_SDA0.67––
SMBUS_SMC_5_G3_SCL0.42––
SMBUS_SMC_5_G3_SDA0.42––
SMBUS_SOC_PMU_BR_SCL0.520––
SMBUS_SOC_PMU_BR_SDA0.513––
SMBUS_SOC_PMU_SCL0.522––
SMBUS_SOC_PMU_SDA0.514––
SMC_4FINGERS_RST0.619––
SMC_ACTUATOR_DISABLE_L0.741.200–
SMC_ADAPTER_EN0.74––
SMC_BC_ACOK0.603.400–
SMC_BMON_ISENSE0.754––
SMC_BT_PWR_EN0.720––
SMC_CHGR_INT_L0.60––
SMC_CLK12M_EN0.464––
SMC_CLK32K0.633––
SMC_CPU_HI_ISENSE0.744––
SMC_CPU_IMON_ISENSE0.748––
SMC_CPU_ISENSE0.757––
SMC_CPU_VSENSE0.738––
SMC_CPUDDR_ISENSE0.744––
SMC_CPUGT_IMON_ISENSE0.731––
SMC_CPUGT_ISENSE0.752––
SMC_CPUGT_VSENSE0.739––
SMC_CPUHI_COMP_ALERT_LOL––
SMC_CPUSA_ISENSE0.752––
SMC_CPUSA_VSENSE0.744––
SMC_DCIN_ISENSE0.755––
SMC_DCIN_VSENSE0.747––
SMC_DDR1V2_ISENSE0.752––
SMC_DEBUGPRT_RX_L0.72––
SMC_DEBUGPRT_TX_L0.72––
SMC_DEBUGPRT2_R_RX0.74––
SMC_DEBUGPRT2_R_TX0.74––
SMC_DEBUGPRT2_RX_L0.744––
SMC_DEBUGPRT2_TX_L0.744––
SMC_DELAYED_PWRGD0.74––
SMC_DEV_SUPPLY_L0.740––
SMC_DEV_SUPPLY_R_L0.74––
SMC_FAN_0_CTL0.755––
SMC_FAN_0_TACH0.754––
SMC_FAN_1_CTL0.755––
SMC_FAN_1_TACH0.755––
SMC_GFX_OVERTEMP0.609––
SMC_GFX_PWR_LEVEL_L0.633––
SMC_GFX_SELF_THROTTLE0.631––
SMC_GPU_1V8_ISENSE0.744––
SMC_GPU_CORE_ISENSE0.757––
SMC_GPU_CORE_VSENSE0.738––
SMC_GPU_FB_ISENSE0.154––
SMC_GPU_FBIC_ISENSE0.754––
SMC_GPU_HS_ISENSE0.745––
SMC_GPU_VDDCI_ISENSE0.744––
SMC_GPU_VDDCI_VSENSE0.740––
SMC_LIDOL3.400–
SMC_LID_LEFT0.560––
SMC_LID_LEFT_R0.560––
SMC_LID_R0.716––
SMC_LID_RIGHT0.51––
SMC_LRESET_L0.755––
SMC_LSOC_RST_L0.757––
SMC_ONOFF_L0.723.400–
SMC_OOB1_D2R_L0.740––
SMC_OOB1_R2D_L0.740––
SMC_PBUS_VSENSE0.748––
SMC_PCH_SUSACK_L0.738––
SMC_PCH_SUSWARN_L0.738––
SMC_PECI_L0.729––
SMC_PM_G2_EN0.50––
SMC_PME_S4_DARK_L0.55––
SMC_PME_S4_WAKE_L0.743.200–
SMC_PMIC_INT_L0.480––
SMC_PROCHOT0.747––
SMC_PROCHOT_L0.557––
SMC_RESET_L0.71––
SMC_RST_L0.60––
SMC_RUNTIME_SCI_L0.738––
SMC_SENSOR_ALERT_L0.56––
SMC_SENSOR_PWR_EN0.606––
SMC_SOCPMU_RESET0.54––
SMC_SSDLIM_ISENSE0.754––
SMC_TCK0.75––
SMC_TDI0.749––
SMC_TDO0.749––
SMC_THRMTRIP0.744––
SMC_THRMTRIP_L0.376––
SMC_TMS0.75––
SMC_TOPBLK_SWP_L0.69––
SMC_USBC_INT_L0.64––
SMC_VCCIO_CPU_DIV20.747––
SMC_VIBE_L0.755––
SMC_WAKE_L0.74––
SMC_WAKE_SCI_L0.738––
SMC_WIFI_EVENT_L0.740––
SMC_WIFI_PWR_EN0.490––
SML_PCH_0_CLK0.781––
SML_PCH_0_DATA0.780––
SOC_ALS_LS_EN0.500––
SOC_AWAKE_REQ0.475––
SOC_BOARD_ID_30.470––
SOC_BOARD_REV_00.460––
SOC_BOARD_REV_10.470––
SOC_BOARD_REV_20.470––
SOC_BOOT_CONFIG_00.470––
SOC_CLK_32K0.434––
SOC_DDR_RREF0.525––
SOC_FORCE_DFU0.472––
SOC_JTAG_SEL0.478––
SOC_MIPI0D_REXT0.800––
SOC_MIPI1C_REXT0.800––
SOC_NAND_CEN_00.470––
SOC_PAD_ZQ_A0.450––
SOC_PANIC_L0.482––
SOC_PCH_DBELL_L0.470––
SOC_PMU_BUCK0_FB0.362––
SOC_PMU_BUCK0_LX0.3900.600–
SOC_PMU_BUCK1_FB0.150––
SOC_PMU_BUCK1_LX0.2200.800–
SOC_PMU_BUCK2_FB0.280––
SOC_PMU_BUCK2_LX0.2801.100–
SOC_PMU_BUCK3_FB0.390––
SOC_PMU_BUCK3_LX0.4001.800–
SOC_PMU_CLK_32K0.436––
SOC_PMU_I2C_SCL0.482––
SOC_PMU_I2C_SDA0.479––
SOC_PMU_INCKT_OTP0.003––
SOC_REQUEST_DFU10.470––
SOC_REQUEST_DFU20.470––
SOC_ROM_SPI_CLK0.450––
SOC_ROM_SPI_CLK_R0.463––
SOC_ROM_SPI_CS_L0.475––
SOC_ROM_SPI_MISO0.436––
SOC_ROM_SPI_MISO_R0.413––
SOC_ROM_SPI_MOSI0.460––
SOC_ROM_SPI_MOSI_R0.478––
SOC_ROM_SPI_RST_L0.613––
SOC_ROM_SPI_WP_L0.550––
SOC_S2R_ACK_L0.790––
SOC_SLEEP1_REQ0.475––
SOC_SPI_BOOT_STATUS0.481––
SOC_SWCLK0.482––
SOC_SWCLK_DBG0.492––
SOC_SWD_CLK0.665––
SOC_SWD_LS_EN0.500––
SOC_SWDIO0.482––
SOC_SWDIO_DBG0.491––
SOC_TO_PCH_ALS_UART_TXD0.460––
SOC_TO_PCH_UART_TXD0.460––
SOC_TO_STOCKHOLM_DEV_WAKE0.478––
SOC_TO_STOCKHOLM_DWLD_REQ0.478––
SOC_TO_STOCKHOLM_EN0.470––
SOC_UART_D2R0.448––
SOC_UART_LS_EN0.573––
SOC_UART_R2D0.45––
SOC_UART_RTS_L0.570––
SOC_USB_REXT0.200––
SOC_USB_VBUS0.767––
SOC_WDOG_RST0.482––
SOC_XTAL_24M_I0.814––
SOC_XTAL_24M_O0.800––
SOC_XTAL_24M_O_R0.800––
SPI_ALT_CLK0.73––
SPI_ALT_CS_L0.70––
SPI_ALT_IO0_MOSI0.62––
SPI_ALT_IO1_MISO0.60––
SPI_ALT_IO2_WP_L0.60––
SPI_ALT_IO3_HOLD_L0.63––
SPI_CLK0.560––
SPI_CLK_R0.550––
SPI_CS0_L0.660––
SPI_CS0_R_L0.670––
SPI_DESCRIPTOR_OVERRIDE1.747––
SPI_DESCRIPTOR_OVERRIDE_L0.748––
SPI_IO<2>0.600––
SPI_IO<3>0.570––
SPI_IO2_R0.560––
SPI_IO2_STRAP_L0.720––
SPI_IO3_R0.720––
SPI_MISO0.570––
SPI_MISO_R0.590––
SPI_MLB_CLK0.71––
SPI_MLB_CS_L0.692––
SPI_MLB_IO0_MOSI0.607––
SPI_MLB_IO1_MISO0.589––
SPI_MLB_IO2_WP_L0.593––
SPI_MLB_IO3_HOLD_L0.60––
SPI_MLBROM_CS_L0.664––
SPI_MOSI0.710––
SPI_MOSI_R0.300––
SPI_MOSI_R_CONN0.86––
SPIROM_USE_MLB0.71––
SPKR_ID00.759––
SPKR_ID0_NC0.79––
SPKRAMP_R_SCLK0.356––
SPKRAMP_TL_LRCLK0.350––
SPKRAMP_TL_OUT_NEG0.583––
SPKRAMP_TL_OUT_POS0.579––
SPKRAMP_TL_SCLK0.350––
SPKRAMP_TL_SDIN0.350––
SPKRAMP_TR_OUT_NEG0.587––
SPKRAMP_TR_OUT_POS0.587––
SPKRAMP_WL_LRCLK0.358––
SPKRAMP_WL_OUT_NEG0.583––
SPKRAMP_WL_OUT_POS0.583––
SPKRAMP_WL_SCLK0.358––
SPKRAMP_WL_SDIN0.358––
SPKRAMP_WR_LRCLK0.357––
SPKRAMP_WR_OUT_NEG0.589––
SPKRAMP_WR_OUT_POS0.587––
SPKRAMP_WR_SCLK0.358––
SPKRAMP_WR_SDIN0.357––
SPKRCONN_TL_OUT_NEG0.583––
SPKRCONN_TL_OUT_POS0.579––
SPKRCONN_TR_OUT_NEG0.587––
SPKRCONN_TR_OUT_POS0.588––
SPKRCONN_WL_OUT_NEG0.583––
SPKRCONN_WL_OUT_POS0.583––
SPKRCONN_WR_OUT_NEG0.588––
SPKRCONN_WR_OUT_POS0.588––
SPROM_CLK0.653––
SPROM_CS0.675––
SPROM_DIN0.639––
SPROM_DOUT0.676––
SSD_3V3_SS0.753––
SSD_BOOT_L0.44––
SSD_BOOT_LB_L0.448––
SSD_CLKREQ_L1.753––
SSD_CLKREQ_L_R0.760––
SSD_CLKREQ_LB_L0.766––
SSD_DEBUG_I2C_CLK0.654––
SSD_DEBUG_I2C_CLK_CONN0.677––
SSD_DEBUG_I2C_DAT0.658––
SSD_DEBUG_I2C_DAT_CONN0.670––
SSD_DEBUG_MUX_OE0.542––
SSD_DEBUGI2C_SEL_PCH0.563––
SSD_FVREF00.469––
SSD_GP00.000––
SSD_GP80.001––
SSD_GP90.762––
SSD_GP100.772––
SSD_GP120.460––
SSD_I2C_CLK0.553––
SSD_I2C_DAT0.559––
SSD_NAND_FA_ZQ0.254––
SSD_NAND_FE_RDY0.570––
SSD_NAND_FF_RDY0.582––
SSD_NAND_FG_RDY0.573––
SSD_P3V3_NAND_CT0.753––
SSD_PGOOD_L0.543––
SSD_PMIC_LDO0.503––
SSD_PWR_EN0.50––
SSD_PWR_LB_EN0.521––
SSD_PWRCON00.450––
SSD_PWRCON1_R00.532––
SSD_PWRCON1_R10.533––
SSD_PWRCON1_R20.545––
SSD_PWRCON20.440––
SSD_PWRCON30.439––
SSD_RESET_B_L0.564––
SSD_RESET_L0.46––
SSD_RESET_LB_L0.767––
SSD_SR_EN_L0.570––
SSD_SVREF10.758––
SSD_SZQ0.255––
SSD_VREF_CA0.787––
SSD_VREF_DQ0.781––
SSD_ZQ00.255––
SW1_EXT_ON0.550––
SYS_DETECT_LOL––
SYSCLK_CLK24M_X10.470––
SYSCLK_CLK24M_X20.470––
SYSCLK_CLK24M_X2_R0.470––
SYSCLK_CLK32K_CAMERA_BT_AP0.42––
SYSCLK_CLK32K_OSC_SOCOL––
SYSCLK_CLK32K_OSC_Y19010.469––
TBA_AUX_DET0.61––
TBA_BGATE0.628––
TBA_BOOT10.58––
TBA_BOOT1_RC0.580––
TBA_BOOT20.58––
TBA_BOOT2_RC0.580––
TBA_COMP0.61––
TBA_CSI_N0.5520.000–
TBA_CSI_P0.5520.000–
TBA_CSI_R_N0.55020.000–
TBA_CSI_R_P0.55020,000–
TBA_CSO_N0.36013.100–
TBA_CSO_P0.36013.100–
TBA_CSO_R_N0.36013.100–
TBA_CSO_R_P0.36013.100–
TBA_GATE_Q10.83––
TBA_GATE_Q20.48––
TBA_GATE_Q30.47––
TBA_GATE_Q40.83––
TBA_LX10.38––
TBA_LX20.38––
TBA_PHASE10.36013,100–
TBA_PHASE20.36013,100–
TBA_VDDA0.44––
TBA_VDDP0.44––
TBT_POC_RESET0.720––
TBT_T_CIO_PLUG_EVENT_L0.605––
TBT_T_CIO_PWR_EN0.600––
TBT_T_CLKREQ_L0.605––
TBT_T_CLKREQ_L_R0.780––
TBT_T_DPMUX_SEL0.790––
TBT_T_FORCE_PWR0.607––
TBT_T_HDMI_DDC_CLK0.607––
TBT_T_HDMI_DDC_DATA0.606––
TBT_T_PCI_RESET_L0.561––
TBT_T_PCIE_BIAS0.780––
TBT_T_RBIAS0.780––
TBT_T_ROM_HOLD_L0.702––
TBT_T_ROM_WP_L0.600––
TBT_T_RSENSE0.000––
TBT_T_SPI_CLK0.574––
TBT_T_SPI_CLK_DBG0.673––
TBT_T_SPI_CS_L0.600––
TBT_T_SPI_MISO0.605––
TBT_T_SPI_MOSI0.611––
TBT_T_TEST_PWR_GOOD0.100––
TBT_T_TMU_CLK_IN0.577––
TBT_T_TMU_CLK_OUT0.579––
TBT_T_USB_PWR_EN0.598––
TBT_T_XTAL25M_IN0.827––
TBT_T_XTAL25M_OUT_R0.770––
TBT_TA_USB2_RBIAS0.500––
TBT_TB_LSTX0.609––
TBT_TB_USB2_RBIAS0.500––
TBT_W_CLKREQ_L0.783––
TBT_W_PCI_RESET_L0.786––
TBT_W_USB_PWR_EN0.590––
TBT_X_CIO_PLUG_EVENT_L0.608––
TBT_X_CIO_PWR_EN0.60––
TBT_X_CLKREQ_L0.613––
TBT_X_CLKREQ_L_R0.773––
TBT_X_DPMUX_SEL0.570––
TBT_X_FORCE_PWR0.60––
TBT_X_HDMI_DDC_CLK0.607––
TBT_X_HDMI_DDC_DATA0.608––
TBT_X_PCI_RESET_L0.570––
TBT_X_PCIE_BIAS0.785––
TBT_X_RBIAS0.78––
TBT_X_ROM_HOLD_L0.70––
TBT_X_ROM_WP_L0.60––
TBT_X_RSENSE0.000––
TBT_X_SPI_CLK0.57––
TBT_X_SPI_CLK_DBG0.677––
TBT_X_SPI_CS_L0.61––
TBT_X_SPI_MISO0.580––
TBT_X_SPI_MOSI0.612––
TBT_X_TEST_EN0.990––
TBT_X_TEST_PWR_GOOD0.990––
TBT_X_TMU_CLK_IN0.578––
TBT_X_TMU_CLK_OUT0.57––
TBT_X_USB_PWR_EN0.60––
TBT_X_XTAL25M_IN0.830––
TBT_X_XTAL25M_OUT_R0.760––
TBT_XB_LSRX0.606––
TBT_XB_LSTX0.606––
TBTTHMSNS_T_ALERT_L0.57––
TBTTHMSNS_T_D1_N0.000––
TBTTHMSNS_T_D1_P0.620––
TBTTHMSNS_T_THM_L0.58––
TBTTHMSNS_X_ALERT_L0.56––
TBTTHMSNS_X_D1_N0.000––
TBTTHMSNS_X_D1_P0.620––
TBTTHMSNS_X_THM_L0.58––
TBTTPOCRST_CT0.748––
TBTTPOCRST_SNS1.400––
TBTXPOCRST_CT0.750––
TBTXPOCRST_SNS1.400––
TP_BMON_IOUTOL––
TP_CARBON_INT1OL––
TP_CARBON_INT2OL––
TP_CPU_RSVD_AA140.007––
TP_CPU_RSVD_AE290.004––
TP_CPU_RSVD_R140.007––
TP_DPA_IG_HPD0.640––
TP_DPMUX_UC_P600.639––
TP_DPMUX_UC_P610.638––
TP_EG_BKLT_PWM0.377––
TP_GPUVCORE_IMON0.604––
TP_J3300_P20.17––
TP_J3300_P560.17––
TP_JB500_P2OL––
TP_JB500_P56OL––
TP_PCH_DMIC_CLK00.789––
TP_PCH_DMIC_CLK10.790––
TP_PCH_DMIC_DATA00.789––
TP_PCH_DMIC_DATA10.790––
TP_PVDDCI_GPU_EN0.632––
TP_Q3100_DRAIN0.643––
TP_Q3200_DRAIN0.63––
TP_QB300_DRAIN0.628––
TP_QB400_DRAIN0.634––
TP_SOC_CLKOUT0.481––
TP_SOC_JTAG_TDI0.479––
TP_SOC_JTAG_TDO0.479––
TP_SOC_JTAG_TRST_L0.480––
TP_SOC_TST_CKOUT0.486––
TP_SYS_ONEWIRE0.747––
TP_U9900_5OL––
TP_UPC_TA_DBG_UART_RX0.764––
TP_UPC_TA_DBG_UART_TX0.767––
TP_UPC_TA_SWD_CLK0.747––
TP_UPC_TA_SWD_DATA0.748––
TP_UPC_TB_DBG_UART_RX0.765––
TP_UPC_TB_DBG_UART_TX0.767––
TP_UPC_TB_SWD_CLK0.740––
TP_UPC_TB_SWD_DATA0.740––
TP_UPC_XA_SWD_CLK0.745––
TP_UPC_XA_SWD_DATA0.745––
TP_UPC_XB_DBG_UART_RX0.770––
TP_UPC_XB_DBG_UART_TX0.773––
TP_UPC_XB_SWD_CLK0.740––
TP_UPC_XB_SWD_DATA0.742––
TPAD_SPI_CLK0.81––
TPAD_SPI_CLK_CONN0.81––
TPAD_SPI_CLK_R0.785––
TPAD_SPI_CS_L0.81––
TPAD_SPI_CS_L_CONN0.87––
TPAD_SPI_CS_L_R0.786––
TPAD_SPI_IF_EN0.540––
TPAD_SPI_IF_EN_CONN0.69––
TPAD_SPI_INT_L0.691––
TPAD_SPI_INT_L_CONN0.68––
TPAD_SPI_MISO0.78––
TPAD_SPI_MISO_R0.78––
TPAD_SPI_MOSI0.81––
TPAD_SPI_MOSI_R0.785––
UNCONNECTED_397OL––
UNCONNECTED_398OL––
UPC_T_5V_EN0.540––
UPC_T_SPI_CLK0.571––
UPC_T_SPI_CS_L0.595––
UPC_T_SPI_MISO0.600––
UPC_T_SPI_MOSI0.599––
UPC_TA_DBG10.775––
UPC_TA_DBG20.774––
UPC_TA_DBG30.769––
UPC_TA_DBG40.774––
UPC_TA_FAULT_L0.760––
UPC_TA_GATE10.653––
UPC_TA_GATE20.644––
UPC_TA_HPD_RX0.778––
UPC_TA_I2C_ADDR0.001––
UPC_TA_R_OSC0.534––
UPC_TA_SPI_CLK0.580––
UPC_TA_SPI_CS_L0.610––
UPC_TA_SPI_MISO0.619––
UPC_TA_SPI_MOSI0.615––
UPC_TA_SS0.533––
UPC_TA_UART_RX0.757––
UPC_TA_UART_TX0.722––
UPC_TB_DBG30.773––
UPC_TB_DBG40.773––
UPC_TB_FAULT_L0.757––
UPC_TB_GATE10.651––
UPC_TB_GATE20.643––
UPC_TB_HPD_RX0.776––
UPC_TB_R_OSC0.524––
UPC_TB_SS0.528––
UPC_X_5V_EN0.544––
UPC_X_SPI_CLK0.574––
UPC_X_SPI_CS_L0.598––
UPC_X_SPI_MISO0.601––
UPC_XA_DBG_UART_RX0.770––
UPC_XA_DBG_UART_TX0.772––
UPC_XA_FAULT_L0.755––
UPC_XA_GATE10.658––
UPC_XA_GATE20.649––
UPC_XA_HPD_RX0.001––
UPC_XA_R_OSC0.528––
UPC_XA_SS0.252––
UPC_XA_UART_RX0.759––
UPC_XA_UART_TX0.510––
UPC_XB_FAULT_L0.750––
UPC_XB_GATE10.649––
UPC_XB_GATE20.64––
UPC_XB_HPD_RX0.000––
UPC_XB_R_OSC0.528––
UPC_XB_SPI_CLK0.591––
UPC_XB_SPI_CS_L0.624––
UPC_XB_SPI_MISO0.630––
UPC_XB_SPI_MOSI0.638––
UPC_XB_SS0.526––
USB_TEST_N0.63––
USB_TEST_P0.62––
USB_UPC_PCH_TA_N0.570––
USB_UPC_PCH_TA_P0.570––
USB_UPC_PCH_TB_N0.570––
USB_UPC_PCH_TB_P0.570––
USB_UPC_PCH_XA_N0.575––
USB_UPC_PCH_XA_P0.575––
USB_UPC_PCH_XB_N0.580––
USB_UPC_PCH_XB_P0.580––
USB_UPC_TA_F_N0.570––
USB_UPC_TA_F_P0.570––
USB_UPC_TA_N0.690––
USB_UPC_TA_P0.690––
USB_UPC_TB_F_N0.610––
USB_UPC_TB_F_P0.610––
USB_UPC_TB_N0.709––
USB_UPC_TB_P0.705––
USB_UPC_XA_F_N0.600––
USB_UPC_XA_F_P0.600––
USB_UPC_XA_N0.640––
USB_UPC_XA_P0.640––
USB_UPC_XB_F_N0.610––
USB_UPC_XB_F_P0.610––
USB_UPC_XB_N0.640––
USB_UPC_XB_P0.640––
USB2_COMP0.114––
USB2_ID0.773––
USB2_UPC_TA_N0.570––
USB2_UPC_TA_P0.570––
USB2_UPC_TB_N0.610––
USB2_UPC_TB_P0.610––
USB2_UPC_XA_N0.600––
USB2_UPC_XA_P0.600––
USB2_UPC_XB_N0.610––
USB2_UPC_XB_P0.610––
USB2_VBUSSENSE0.775––
USB3_EXTA_R2D_C_N0.410––
USB3_EXTA_R2D_C_P0.410––
USB3_EXTA_R2D_N0.771––
USB3_EXTA_R2D_P0.772––
USB3_TEST_D2R_N0.45––
USB3_TEST_D2R_P0.45––
USB3_TEST_R2D_N0.42––
USB3_TEST_R2D_P0.42––
USBC_T_RESET_L0.733––
USBC_T_RESET_L_R0.549––
USBC_TA_CC10.605––
USBC_TA_CC20.614––
USBC_TA_D2R_N<1>0.329––
USBC_TA_D2R_N<2>0.327––
USBC_TA_D2R_P<1>0.328––
USBC_TA_D2R_P<2>0.327––
USBC_TA_R2D_N<1>OL––
USBC_TA_R2D_N<2>OL––
USBC_TA_R2D_P<1>OL––
USBC_TA_R2D_P<2>OL––
USBC_TA_SBU10.873––
USBC_TA_SBU20.835––
USBC_TA_USB_BOT_NOL––
USBC_TA_USB_BOT_POL––
USBC_TA_USB_TOP_N0.600––
USBC_TA_USB_TOP_POL––
USBC_TB_CC10.598––
USBC_TB_CC20.608––
USBC_TB_D2R_N<1>0.329––
USBC_TB_D2R_N<2>0.329––
USBC_TB_D2R_P<1>0.329––
USBC_TB_D2R_P<2>0.329––
USBC_TB_R2D_N<1>OL––
USBC_TB_R2D_N<2>OL––
USBC_TB_R2D_P<1>OL––
USBC_TB_R2D_P<2>OL––
USBC_TB_SBU10.857––
USBC_TB_SBU20.819––
USBC_TB_USB_BOT_NOL––
USBC_TB_USB_BOT_POL––
USBC_TB_USB_TOP_NOL––
USBC_TB_USB_TOP_POL––
USBC_X_RESET_L0.732––
USBC_X_RESET_L_R0.540––
USBC_XA_CC10.602––
USBC_XA_CC20.60––
USBC_XA_D2R_N<2>0.357––
USBC_XA_D2R_P<2>0.358––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_SBU10.869––
USBC_XA_SBU20.864––
USBC_XA_USB_DBG_BOT_NOL––
USBC_XA_USB_DBG_BOT_POL––
USBC_XB_CC10.60––
USBC_XB_CC20.61––
USBC_XB_D2R_N<1>0.355––
USBC_XB_D2R_N<2>0.358––
USBC_XB_D2R_P<1>0.356––
USBC_XB_D2R_P<2>0.357––
USBC_XB_R2D_N<1>OL––
USBC_XB_R2D_N<2>OL––
USBC_XB_R2D_P<1>OL––
USBC_XB_R2D_P<2>OL––
USBC_XB_SBU10.789––
USBC_XB_SBU20.790––
USBC_XB_USB_BOT_NOL––
USBC_XB_USB_BOT_POL––
USBC_XB_USB_TOP_NOL––
USBC_XB_USB_TOP_POL––
VDDCIS0_CS_N0.019––
VDDCIS0_CS_P0.019––
VR_PHASE_GPU_VDDCI0.0180.90026.24R
VR0V9_IND_TBT_T0.2450.900–
VR0V9_IND_TBT_X0.2200.900–
VREF_AMP_TL0.000––
VREF_AMP_TR0.574––
VRVDDCI_R0.0180.90026.24R
WIFI_SROM_ORG0.695––
WIFI_SW_CAP0.670––
WL_CLK32K0.486––
WLAN_1P2V_EN0.579––
WLAN_3V3_VMONOL––
WLAN_JTAG_SEL0.600––
WLAN_JTAG_TCK0.572––
WLAN_JTAG_TDI0.579––
WLAN_JTAG_TMS0.608––
WLAN_JTAG_TRST_L0.570––
WLAN_STRAP_00.500––
WLAN_STRAP_10.460––
WLAN_UART_RX0.600––
WLAN_UART_TX0.608––
X29THMSNS_A00.627––
XDP_BPM_L<0>0.299––
XDP_BPM_L<1>0.298––
XDP_BPM_L<2>0.300––
XDP_BPM_L<3>0.302––
XDP_CPU_PRDY_L0.26––
XDP_CPU_PREQ_L0.29––
XDP_CPU_PWRBTN_L0.740––
XDP_CPU_TCK0.052––
XDP_CPU_TDI0.257––
XDP_CPU_TDO0.232––
XDP_CPU_TMS0.258––
XDP_CPU_TRST_L0.307––
XDP_DBRESET_L0.741––
XDP_PCH_OBSDATA_A00.787––
XDP_PCH_OBSDATA_A10.788––
XDP_PCH_OBSDATA_A20.788––
XDP_PCH_OBSDATA_A30.788––
XDP_PCH_OBSDATA_B00.788––
XDP_PCH_OBSDATA_B10.788––
XDP_PCH_OBSDATA_B20.789––
XDP_PCH_OBSDATA_B30.790––
XDP_PCH_OBSDATA_C00.754––
XDP_PCH_OBSDATA_C10.752––
XDP_PCH_OBSDATA_C20.760––
XDP_PCH_OBSDATA_C30.753––
XDP_PCH_OBSDATA_D00.789––
XDP_PCH_OBSDATA_D10.790––
XDP_PCH_OBSDATA_D20.789––
XDP_PCH_OBSDATA_D30.790––
XDP_PCH_OBSFN_C00.788––
XDP_PCH_OBSFN_C10.789––
XDP_PCH_TCK0.423––
XDP_PCH_TDI0.261––
XDP_PCH_TDO0.243––
XDP_PCH_TMS0.262––
XDP_PCH_TRST_L0.29––
XDP_PM_RSMRST_L1.480––
XDP_PRESENT_CPU1.308––
XDP_PRESENT_L0.513––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00928?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00928: diode 0.360, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00928?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00928: diode 0.34, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00928?

OpenBoardData's known-good values for PP5V_S5 on the 820-00928: diode 0.46. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00928 board?

Open your own 820-00928 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License