Apple laptop board · OpenBoardData
820-01700 known-good readings
Known-good readings for the Apple laptop board 820-01700: 1,794 nets, including 105 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 105 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-01700.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 105 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 43
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_G3S | 0.301 | 1.80 | – |
AI: what PP1V8_G3S is and how to check itPP1V8_G3S is the 1.8 V rail enabled by P1V8G3S_EN in the G3S (always-on) power stage, judging from its name and its place in the boot sequence. Known-good readings for this board: diode 0.301 to ground and 1.80 V with power applied; no other known-good values are recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.301 suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points back to the enable or the rail's supply. These are community readings and only a guide, so compare against a matching rail on a known-good board before condemning anything. | |||
PP1V8_G3S_TPAD_CONN | 0.544 | – | – |
AI: what PP1V8_G3S_TPAD_CONN is and how to check itPP1V8_G3S_TPAD_CONN is a 1.8 V rail feeding the trackpad connector; the G3S part of the name indicates it belongs to the G3H always-on group, so it should be present early in the boot sequence, before the S5/S3 rails come up. The only known-good reading in the archive is diode mode 0.544 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the net, then measure the voltage with power applied. A diode reading far from 0.544 usually points to a short or a damaged component on that net, but a single reading isn't proof, so confirm with a second measurement before replacing anything. | |||
PP1V8_G3S_WLANBT | 0.301 | – | – |
AI: what PP1V8_G3S_WLANBT is and how to check itPP1V8_G3S_WLANBT — a 1.8 V rail for the WLAN/Bluetooth section, and the G3S suffix (from the name) puts it in the always-on G3H group, so it should be present whenever the board has valid standby power.
| |||
PP3V0_G3H_RTC | 0.461 | – | – |
AI: what PP3V0_G3H_RTC is and how to check itPP3V0_G3H_RTC is an always-on 3.0 V rail feeding the RTC section; the G3H part means "always on" from the name, so it should be present whenever a valid external PSU, battery or charger is connected. The only known-good reading here is a diode value of 0.461 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage. A diode reading far below 0.461 suggests a short or leaky part on the rail, while a much higher reading suggests an open trace or missing connection; a single reading isn't proof a part is bad. | |||
PP3V3_G3H_DFR | 0.420 | – | – |
AI: what PP3V3_G3H_DFR is and how to check itPP3V3_G3H_DFR is a 3.3 V always-on rail; the G3H part of the name indicates it comes up in the always-on startup stage, and DFR is a suffix from the name. The only known-good reading in the archive is a diode value of 0.420, with no condition recorded; there is no known-good voltage here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.420 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything. | |||
PP3V3_G3H_MESA_SW | 0.377 | – | – |
AI: what PP3V3_G3H_MESA_SW is and how to check itPP3V3_G3H_MESA_SW is a 3.3 V always-on rail in the G3H group, judging by its name (G3H = always on), and it sits early in the boot sequence near PP3V3_G3H_RTC and PP3V3_G3H. The archive lists one known-good diode reading of 0.377; treat it as a community guide, and there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power up and measure the voltage. A diode value far from 0.377 usually points to a short or a damaged component on that net, but one reading isn't proof — confirm with a second measurement before replacing anything. | |||
PP3V3_G3H_PMU_VINRTC_R | 0.421 | – | – |
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check itPP3V3_G3H_PMU_VINRTC_R is an always-on 3.3 V rail feeding the PMU's RTC/input supply; the G3H part of the name indicates it comes up in the always-on startup stage, and the VINRTC part says it feeds the RTC input. The only known-good reading here is a diode value of 0.421 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode, red probe on ground and black on the rail, then power the board and measure the DC voltage at the rail. A diode reading far below 0.421 usually points to a short or a leaky load on the rail; a far higher or open reading points to a broken trace or missing feed. Voltage behaviour is best judged against the boot sequence, where this rail should be present before PP1V8_SLPS2R appears. | |||
PP3V3_G3H_RSLOC | 0.383 | – | – |
AI: what PP3V3_G3H_RSLOC is and how to check itPP3V3_G3H_RSLOC is a 3.3 V always-on rail: the G3H part of the name marks it as a startup-stage rail, and RSLOC is a suffix that the name alone doesn't explain. The only known-good figure here is a diode reading of 0.383 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, black probe on ground, red on the rail, then confirm the voltage with power applied. A diode value far from 0.383 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
PP3V3_G3H_RTC_REG_R | 0.421 | 3.300 | – |
AI: what PP3V3_G3H_RTC_REG_R is and how to check itPP3V3_G3H_RTC_REG_R is a 3.3 V always-on rail in the G3H startup group, which from its name is present whenever the board has valid power, before the main power sequence runs. Known-good readings in the archive: diode 0.421 to ground and 3.300 V with power applied; no known-good resistance value is listed.
A diode reading far below 0.421 suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken trace or missing feed. A missing or low voltage with a normal diode reading points upstream, at the rail's source or its enable, rather than at the rail itself. These are community readings and vary with board state, so treat them as a guide, not a guarantee. | |||
PP3V3_G3H_RTC_X | 0.421 | – | – |
AI: what PP3V3_G3H_RTC_X is and how to check itPP3V3_G3H_RTC_X is a 3.3 V always-on rail tied to the RTC domain; the "G3H" and "RTC" parts come from the name, and the boot sequence lists PP3V3_G3H_RTC early, right after PBUS, so it should be present before the later rails.
| |||
PP3V3_G3H_SOCPMU | 0.378 | 3.300 | – |
AI: what PP3V3_G3H_SOCPMU is and how to check itPP3V3_G3H_SOCPMU is a 3.3 V always-on rail feeding the SOC power management side; the G3H part of the name indicates it belongs to the always-on startup stage, and the SOCPMU suffix points to the SOC PMU domain (from the name, not from a schematic).
| |||
PP3V3_G3H_SSD0_SNS | 0.421 | 3.300 | – |
AI: what PP3V3_G3H_SSD0_SNS is and how to check itPP3V3_G3H_SSD0_SNS — the name says it's a 3.3 V G3H rail (always-on), with the SSD0 and SNS suffix pointing to a sense line on the SSD0 supply. It appears in the SSD landing stages of the boot sequence, after the SSD is told to go active.
| |||
PP3V3_G3H_SSD1_SNS | 0.377 | 3.300 | – |
AI: what PP3V3_G3H_SSD1_SNS is and how to check itPP3V3_G3H_SSD1_SNS is a 3.3 V always-on rail in the G3H group (that grouping comes from the name), tied to SSD1 sensing on this 820-01700. The archive lists a known-good diode reading of 0.377 and a voltage of 3.300; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A voltage well below 3.3 V points to the rail not coming up or being loaded down, and a diode reading far from 0.377 suggests a short or open on that net; no known-good resistance value is recorded here. | |||
PP3V3_G3H_T | 0.378 | 3.300 | – |
AI: what PP3V3_G3H_T is and how to check itPP3V3_G3H_T is an always-on 3.3 V rail in the G3H startup stage, judged from its name. The archived readings for this net are diode 0.378 and voltage 3.300; these are community values and a guide only, with no condition recorded. Check it with the board unpowered in diode mode from the net to ground, then power up and measure the voltage. A voltage well below 3.3 V or a diode reading far from 0.378 points to a short, a missing enable or a failed source, but one reading alone doesn't confirm a bad part. No known-good resistance reading exists here, so compare against a matching net or a known-good board. | |||
PP3V3_G3HSW_DFR | 0.568 | – | – |
AI: what PP3V3_G3HSW_DFR is and how to check itPP3V3_G3HSW_DFR — a 3.3 V rail, from its name. The "G3H" part means it belongs to the always-on G3H group, so it should be present whenever the board has valid power, before the main power-on sequence runs.
| |||
PP3V3_G3S_T | 0.428 | – | – |
AI: what PP3V3_G3S_T is and how to check itPP3V3_G3S_T is a 3.3 V G3S rail; the G3S stage in its name sits after the always-on G3H rails in the boot sequence, so it comes up once the G3S enables run. The only known-good figure here is a diode reading of 0.428 to ground, with no condition noted; there is no known-good voltage reading for this rail.
A diode reading far below 0.428 usually suggests a short or a leaky part on the rail; a much higher one can mean an open path. Neither confirms a bad part on its own, so check the voltage next before replacing anything. | |||
PP3V3_G3S_WLAN | 0.349 | – | – |
AI: what PP3V3_G3S_WLAN is and how to check itPP3V3_G3S_WLAN is a 3.3 V always-on (G3S) supply for the WLAN section, as the name suggests; it appears in the boot sequence after PP3V3_G3S and before the S0 rails, and the WLAN clock PMU_CLK32K_WLANBT follows it. The only known-good figure here is a diode reading of 0.349 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then compare with 0.349; a much lower reading suggests a short or leaky load on the rail. With power applied, measure the voltage on the rail and expect roughly 3.3 V, though that value is general and not from this board's data. A far-off diode reading points to a fault on the rail or its loads, but one reading alone doesn't confirm a bad part. | |||
PP3V3_G3S_X | 0.349 | – | – |
AI: what PP3V3_G3S_X is and how to check itPP3V3_G3S_X is a 3.3 V rail in the G3S group; the "G3S" part comes from the name and in this board's sequence PP3V3_G3S comes up after P3V3G3S_EN, during the SSD power-up stage. The archive lists one known-good reading: diode 0.349 to ground (no condition noted). Check it with the board unpowered in diode mode, probe to ground, then measure the voltage with power applied. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.349 usually points to a short or a damaged part on that rail, but one reading isn't proof; confirm with a second measurement before replacing anything. | |||
PP3V3_G3SSW_SNS | 0.494 | 3.400 | – |
AI: what PP3V3_G3SSW_SNS is and how to check itPP3V3_G3SSW_SNS is a 3.3 V always-on switch rail; the "G3" in the name marks it as part of the always-on G3H stage in the boot sequence, and "SNS" suggests it is a sense line for that rail (from the name, not confirmed by a schematic).
| |||
PP5V_G3S | 0.405 | 5.000 | – |
AI: what PP5V_G3S is and how to check itPP5V_G3S is a 5 V always-on rail in the G3H group, judged from its name. Known-good readings here are diode 0.405 and voltage 5.000; no condition is recorded, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.405 suggests a short or leaky load on the rail, and a missing 5 V points back to its enable, P5VG3S_EN, and the supply feeding it. | |||
PP5V_G3S_BKLT_A | 0.413 | 5.100 | – |
AI: what PP5V_G3S_BKLT_A is and how to check itPP5V_G3S_BKLT_A — a 5 V backlight rail in the G3S (always-on) domain, judged from the name; the boot sequence lists the G3S rails (PP5V_G3S, PP3V3_G3S, PP1V8_G3S) early, before the S-state rails.
| |||
PP5V_G3S_BKLT_D | 0.413 | 5.100 | – |
AI: what PP5V_G3S_BKLT_D is and how to check itPP5V_G3S_BKLT_D is a 5 V backlight rail that sits in the G3S always-on group, judging from the name (G3S = always-on state, BKLT = backlight). The archive lists a known-good diode reading of 0.413 and a voltage of 5.100; no condition is recorded for either, so treat them as a guide only.
| |||
PP5V_G3S_DFR_FILT | 0.405 | – | – |
AI: what PP5V_G3S_DFR_FILT is and how to check itPP5V_G3S_DFR_FILT is a 5 V rail in the G3S group; the "G3S" in the name indicates it belongs to the always-on startup stage, and "FILT" suggests a filtered version of that 5 V feed (from the name only). The archive lists a known-good diode reading of 0.405 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.405 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken feed or missing connection. Treat the 0.405 as a community guide, not a guaranteed value. | |||
PP5V_G3S_GPU_COREREG_VDD | 0.404 | – | – |
AI: what PP5V_G3S_GPU_COREREG_VDD is and how to check itPP5V_G3S_GPU_COREREG_VDD — from the name, a 5 V GPU core-regulator supply in the G3S (always-on) domain. The archive lists one known-good reading: diode 0.404 to ground, with no condition noted. It has no known-good voltage reading here.
| |||
PP5V_G3S_GPU_VDD075REG_R | 0.405 | – | – |
AI: what PP5V_G3S_GPU_VDD075REG_R is and how to check it
| |||
PP5V_G3S_ISNS_D | OL | – | – |
AI: what PP5V_G3S_ISNS_D is and how to check itPP5V_G3S_ISNS_D is a current-sense line tied to the PP5V_G3S rail; the "G3S" part of the name places it in the always-on G3H startup stage, and "ISNS" indicates it carries the rail's current-sense signal (this is from the name, not from board data). The only known-good reading recorded is diode mode OL, with no stated condition; there is no known-good voltage here. With the board unpowered, measure diode mode from PP5V_G3S_ISNS_D to ground and compare with that OL figure. Then, with power applied, check the voltage on the line and on PP5V_G3S itself to see whether the rail is up. A diode reading far from OL usually points to a short or a leaky component on that net, but one reading alone doesn't confirm a bad part; compare against PP5V_G3S and the matching sense line before replacing anything. | |||
PP5V_G3S_KBDLED | 0.403 | 5.000 | – |
AI: what PP5V_G3S_KBDLED is and how to check itPP5V_G3S_KBDLED is a 5 V always-on rail, from its name: the G3S state (present whenever the board has standby power) feeding the keyboard backlight. Known-good readings in the archive are diode 0.403 to ground and 5.000 V with power applied; there is no known-good resistance value here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.403 usually points to a short or a leaky load on the rail, while a correct diode reading with missing 5 V points back toward the rail's source or enable. These are community readings and vary with board state, so treat them as a guide and confirm against a matching net before condemning a part. | |||
PP5V_G3S_TPAD_CONN | 0.403 | – | – |
AI: what PP5V_G3S_TPAD_CONN is and how to check itPP5V_G3S_TPAD_CONN is a 5 V rail feeding the trackpad connector; the G3S part of the name places it in the G3H "always on" group, which is from the name, not measured behaviour. The only known-good figure in the archive is a diode reading of 0.403 to ground; there is no known-good voltage here. Check it unpowered in diode mode from the net to ground, then apply power and measure the voltage at the connector. A diode reading far from 0.403 usually points to a short or a damaged part on that rail rather than a normal variation, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything. | |||
PP5V_G3S_VCCIOVCC | 0.403 | – | – |
AI: what PP5V_G3S_VCCIOVCC is and how to check it
| |||
PPBUS_G3H | 0.415 | 12.600 | 410.000 |
AI: what PPBUS_G3H is and how to check itPPBUS_G3H is the main battery/charger bus rail; the G3H suffix means "always on" while external power is present, from the name. Known-good readings in the archive: diode 0.415, voltage 12.600 and resistance 410.000 (community values, a guide only, not a spec). Check it unpowered in diode mode to ground first, then with power applied measure the voltage. A diode far below 0.415 suggests a short or leaky part on the rail; a voltage well off 12.600 points to the charger/PPBUS side rather than a downstream rail. No known-good waveform or current reading is recorded here. | |||
PPBUS_G3H_SPKRAMPL | 0.414 | 12.600 | – |
AI: what PPBUS_G3H_SPKRAMPL is and how to check itPPBUS_G3H_SPKRAMPL is a G3H (always-on) rail, judging by the name; the "SPKRAMPL" suffix suggests a speaker/amplifier branch of PPBUS, but that's from the name only. Known-good readings here are diode 0.414 and voltage 12.600; no condition is recorded, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.414 suggests a short or leaky load on that branch; a voltage well off 12.600 points to the PPBUS source or an enable/load fault upstream. No known-good resistance reading exists here, so compare against a matching PPBUS branch or a known-good board. | |||
PPBUS_G3H_SSD0_SNS | 0.415 | 12.600 | 410.000 |
AI: what PPBUS_G3H_SSD0_SNS is and how to check itPPBUS_G3H_SSD0_SNS — the name (G3H) marks it as an always-on rail, and "SSD0_SNS" suggests it's the main bus feeding the SSD section, sensed there. From the name only; the parts on it aren't known. Known-good readings from the archive (a guide, board state varies): diode 0.415, voltage 12.600, resistance 410.000. Check it unpowered first: diode mode to ground on the net, then resistance to ground, both with the board off and discharged. Then power up and measure the voltage, comparing against 12.600. A diode or resistance far below known-good usually points to a short or a leaky part on that rail; a voltage well off 12.600 points to the supply feeding it or a load pulling it down. No known-good value exists for other measurement types here. | |||
PPBUS_G3H_SSD1_SNS | 0.415 | 12.600 | 410.000 |
AI: what PPBUS_G3H_SSD1_SNS is and how to check itPPBUS_G3H_SSD1_SNS is an always-on (G3H, from the name) main power rail sense line tied to the SSD section; the name suggests it carries the main bus voltage and reports it back. Known-good readings from the archive: diode 0.415, voltage 12.600, resistance 410.000 — treat these as a guide only, since readings vary with board state. To check it, power the board off and measure diode mode to ground, then apply power and measure the voltage. A reading far from known-good usually points to a short or open on the rail or its sense path rather than a confirmed bad part; no known-good value of another kind is listed here, so compare against a matching net or a known-good board. | |||
PPDCIN_G3H | 0.550 | 20.000 | – |
AI: what PPDCIN_G3H is and how to check itPPDCIN_G3H is the always-on G3H input rail, as its name indicates; it's the DC-in feed present whenever a valid external supply is connected. In the readings archive its known-good values are a diode reading of 0.550 and a voltage of 20.000; these are community figures and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 20 V points to a supply or input-path problem rather than the rail itself, and a diode reading far from 0.550 suggests a short or open on that net; no known-good resistance reading is recorded here. | |||
PPDCIN_G3H_CHGR | 0.552 | 20.000 | – |
AI: what PPDCIN_G3H_CHGR is and how to check itPPDCIN_G3H_CHGR is the charger-side DC input rail in the always-on G3H domain, judged from its name (G3H = always on). It should be present whenever a valid external supply or battery path is live, before the main power sequence.
| |||
PPDCIN_TA_G3H_F | 0.550 | 20.000 | – |
AI: what PPDCIN_TA_G3H_F is and how to check itPPDCIN_TA_G3H_F is a G3H (always-on) rail, judging from its name, so it should be present whenever a valid external supply is connected. The archive lists a known-good diode reading of 0.550 and a voltage of 20.000 V; treat these as a community guide, not a guaranteed value. Check it unpowered in diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far from 0.550 usually points to a short or a damaged component on that rail, while missing voltage points upstream to the supply input path. No other known-good readings are recorded for this net. | |||
PPDCIN_TB_G3H_F | 0.550 | 20.000 | – |
AI: what PPDCIN_TB_G3H_F is and how to check itPPDCIN_TB_G3H_F is an always-on (G3H, from the name) DC-in rail associated with the Thunderbolt/USB-C input side of the 820-01700; the name suggests it's present whenever external power is connected, before the main power sequence runs. Known-good readings from the archive: diode 0.550 to ground, voltage 20.000 V with power applied. Treat these as a guide, since community readings vary with board state. To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply the correct external supply and measure the voltage on the rail. A diode reading far below 0.550 suggests a short or leaky part on the rail; far above it suggests an open path. A voltage well under 20.000 V points to the input supply, the input path or a load pulling the rail down — but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything. | |||
PPDCIN_XA_G3H_F | 0.550 | 20.000 | – |
AI: what PPDCIN_XA_G3H_F is and how to check itPPDCIN_XA_G3H_F is a DC-input rail in the always-on G3H domain, judging from its name; it's the external power path that should be present whenever a valid supply is connected. The archive lists a known-good diode reading of 0.550 and a voltage of 20.000 V, with no condition noted, so treat these as a guide only.
One reading alone doesn't confirm a bad part; verify with a second measurement before replacing anything. | |||
PPDCIN_XB_G3H_F | 0.550 | 20.000 | – |
AI: what PPDCIN_XB_G3H_F is and how to check itPPDCIN_XB_G3H_F is an always-on G3H rail, judging from the "G3H" in its name; it sits early in the sequence, ahead of PP3V3_G3H_RTC and PP3V3_G3H. The archive lists a known-good diode reading of 0.550 and a voltage of 20.000, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.550 suggests a short or leaky load on the rail; a missing or low voltage with a normal diode reading points upstream, toward the input supply path. No known-good resistance reading is recorded here. | |||
PPVBAT_G3H_CHGR_R | 0.415 | 12.600 | 410.000 |
AI: what PPVBAT_G3H_CHGR_R is and how to check itPPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H part of the name indicates it is an always-on rail, present whenever the board has valid power. Known-good readings in the archive are diode 0.415, voltage 12.600 and resistance 410.000, with no condition recorded, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode or resistance far below known-good usually points to a short or a leaky part on the rail; a voltage far off points to a supply or enable problem upstream. No known-good waveform or current reading exists here, so compare against a matching rail or a known-good board. | |||
PPVBAT_G3H_CHGR_REG | 0.415 | 12.600 | 410.000 |
AI: what PPVBAT_G3H_CHGR_REG is and how to check itPPVBAT_G3H_CHGR_REG is a charger-side battery rail; the G3H part of the name indicates it is always on, and the CHGR_REG part indicates it comes from the charger regulator. Known-good readings in the archive are diode 0.415, voltage 12.600 and resistance 410.000, with no condition recorded, so treat them as a guide only. Check it with the board unpowered and discharged in diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode or resistance far below known-good usually points to a short or a leaky part on the rail, while a voltage far off points to the charger side not regulating; a small difference alone does not condemn a part. | |||
PPVBAT_G3H_CONN | 1.569 | – | – |
AI: what PPVBAT_G3H_CONN is and how to check itPPVBAT_G3H_CONN — the name indicates the battery ("BAT") connection rail in the G3H always-on domain, so it's the battery-side supply present whenever a battery is attached, independent of the power button.
| |||
PPVIN_G3H_P3V3G3HRTC_R | 0.415 | 13.100 | – |
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check itPPVIN_G3H_P3V3G3HRTC_R is an always-on (G3H) rail feeding the RTC section, judging from its name; the boot sequence lists PP3V3_G3H_RTC early, before PP3V3_G3H. Known-good readings here: diode 0.415 and voltage 13.100, with no condition noted. Check it unpowered in diode mode to ground, then with power applied measure the voltage. A diode reading far from 0.415 usually points to a short or leaky part on that net, and a missing voltage points back to its source; no known-good resistance reading is recorded here. | |||
S5 and SUS: standby 8
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_S5 | 0.363 | – | 0.019R |
AI: what PP1V8_S5 is and how to check itPP1V8_S5 is a 1.8 V standby rail; the S5/SUS suffix in its name places it in the standby stage, and the boot sequence lists it alongside PP3V3_S5 and PPVPCORE_S5 as the SSD begins power button monitoring. Known-good readings here are diode 0.363 and resistance 0.019R (community guide, board state not stated). Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far below 0.363 usually points to a short or a leaky part on the rail, but one reading doesn't confirm a fault. | |||
PP1V8_S5_GPIOX_R | 0.364 | – | – |
AI: what PP1V8_S5_GPIOX_R is and how to check itPP1V8_S5_GPIOX_R is a 1.8 V standby rail: the "S5" in the name marks it as an S5/SUS standby rail, and "GPIOX" suggests it feeds GPIO-level signalling rather than a main load (that part is from the name, not from board data). The archive lists one known-good reading: diode 0.364 to ground. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage is present at the S5 stage of the boot sequence. No known-good voltage reading exists here, so treat any voltage figure as unconfirmed. A diode reading far from 0.364 usually points to a short or a damaged part on that net, but one reading alone doesn't prove a part bad. | |||
PP1V8_S5_TBTTHMSNS_T_R | 0.410 | – | – |
AI: what PP1V8_S5_TBTTHMSNS_T_R is and how to check itPP1V8_S5_TBTTHMSNS_T_R is a 1.8 V standby rail (the 1V8 and S5 parts come from the name; the TBTTHMSNS suffix suggests a Thunderbolt thermal-sense signal, which is general interpretation, not from the board data). The archive lists one known-good diode reading: 0.410 in diode mode to ground, with no condition noted and no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the net. A diode value far from 0.410 usually points to a short or a damaged component on that net, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything. | |||
PP1V8_S5_TBTTHMSNS_X_R | 0.410 | – | – |
AI: what PP1V8_S5_TBTTHMSNS_X_R is and how to check itPP1V8_S5_TBTTHMSNS_X_R — from its name, a 1.8 V rail that belongs to the S5 standby stage (the boot sequence lists it with PP3V3_S5, PP1V8_S5 and PPVPCORE_S5, after the SSD power steps). The "TBTTHMSNS" part suggests a Thunderbolt thermal-sense related rail, but that is inference from the name only; the parts on this net aren't documented here.
| |||
PP1V24_S5_PCH_VCCDPHY | 0.428 | – | – |
AI: what PP1V24_S5_PCH_VCCDPHY is and how to check itPP1V24_S5_PCH_VCCDPHY — from the name, a 1.24 V supply for the PCH's display PHY (VCCDPHY), in the S5 standby domain. The archive lists one known-good reading: diode 0.428 to ground, with no condition recorded. Check it unpowered in diode mode, red probe on ground, black on the net; then power the board and confirm about 1.24 V, noting that it should appear at the S5 stage of the boot sequence. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.428 usually suggests a short or leaky load on the rail; far above it suggests an open trace or missing part — confirm with a second measurement before replacing anything. | |||
PP3V3_S5 | 0.335 | – | – |
AI: what PP3V3_S5 is and how to check itPP3V3_S5 is a 3.3 V standby rail, in the S5/SUS standby stage from its name. In the boot sequence it comes up after PMU_ONOFF_L, alongside PP1V8_S5 and PPVPCORE_S5, before SMC_RSMRST_L and the S3 rails. The only known-good reading here is diode 0.335 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.335 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board. | |||
PP3V3_S5_GPIOX_R | 0.335 | – | – |
AI: what PP3V3_S5_GPIOX_R is and how to check itPP3V3_S5_GPIOX_R is a 3.3 V standby rail, judging from its name: the S5/SUS stage in the boot sequence is standby, and the GPIOX suffix suggests it feeds GPIO pull-ups. The only known-good figure here is a diode reading of 0.335 to ground; there is no known-good voltage reading for it.
A diode reading far below 0.335 usually points to a short or a leaky part on the rail; a much higher one can mean an open trace or missing pull-up. A missing 3.3 V in standby points back to the S5 standby supply that feeds it. These are general guidelines, not confirmed causes for this board. | |||
PP5V_S5_LDO | 0.485 | – | – |
AI: what PP5V_S5_LDO is and how to check itPP5V_S5_LDO is a 5 V standby rail: the S5 and LDO parts of the name indicate it belongs to the standby stage, before the main rails come up. The only known-good figure here is a diode reading of 0.485 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with the charger connected. A diode reading far below 0.485 suggests a short or a leaky load on the rail; a reading well above it can mean an open trace or a missing connection. Treat the 0.485 as a community guide, not a guaranteed value. | |||
S4 4
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_SSD0_S4E1_AVDD18_PLL | 0.375 | – | – |
AI: what PP1V8_SSD0_S4E1_AVDD18_PLL is and how to check itPP1V8_SSD0_S4E1_AVDD18_PLL — reference note
| |||
PP1V8_SSD0_S4E1_PCI_AVDD_H | 0.375 | – | – |
AI: what PP1V8_SSD0_S4E1_PCI_AVDD_H is and how to check itPP1V8_SSD0_S4E1_PCI_AVDD_H — reference note
| |||
PP5V_S4_T_USBC | 0.193 | 5.000 | – |
AI: what PP5V_S4_T_USBC is and how to check itPP5V_S4_T_USBC is a 5 V rail in the S4 startup stage, judging by its name (S4 = a sleep/standby stage in the boot sequence); the data doesn't say which parts sit on it. Known-good readings from the archive: diode 0.193 to ground and 5.000 V with power applied; no condition is recorded, so treat these as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.193 suggests a short or leaky load on the rail; a voltage far from 5.000 V with the board powered points to the rail not being enabled or its source failing. There is no known-good resistance reading for this rail. | |||
PP5V_S4_X_USBC | 0.188 | 5.000 | 186.000 |
AI: what PP5V_S4_X_USBC is and how to check itPP5V_S4_X_USBC is a 5 V USB-C rail that belongs to the S4 startup stage, judging by its name. The archive lists known-good readings of diode 0.188, voltage 5.000 V and resistance 186.000; these are community values and vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with power applied. A reading far from known-good usually points to a short or a rail that isn't coming up, but one reading alone doesn't confirm a bad part. No known-good value of another kind is listed here. | |||
S3: memory 6
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S3 | 0.223 | 1.200 | 221.000 |
AI: what PP1V2_S3 is and how to check itPP1V2_S3 is a 1.2 V rail that comes up in the S3 (memory) startup stage, judging from its name and its place in the boot sequence after PP1V8_S3 and PVDDQ_EN. Known-good readings from the archive: diode 0.223, voltage 1.200, resistance 221.000; these are community values and vary with board state. Check it unpowered in diode mode to ground first, then power the board and measure the voltage at the rail. A diode or resistance far below known-good suggests a short or a failing load on the rail; a voltage well off 1.200 with a normal diode reading points more to the rail's enable or supply than to a short. | |||
PP1V2_S3_CPUDDR | 0.220 | 1.200 | 226.000 |
AI: what PP1V2_S3_CPUDDR is and how to check itPP1V2_S3_CPUDDR is a 1.2 V memory rail that comes up in the S3 stage, judging by its name (S3 = memory, CPUDDR = CPU DDR). Known-good readings here are diode 0.220, voltage 1.200 and resistance 226.000, community-sourced so treat them as a guide only. Check it with the board unpowered in diode mode to ground, then confirm 1.200 V with power applied once the board reaches S3. A reading far from these usually points to a short or open on the rail or its supply, not proof of a bad part on one reading. No known-good value exists here beyond those three, so compare against a matching rail or a known-good board if in doubt. | |||
PP1V2_S3_REG_R | 0.223 | 1.200 | 221.000 |
AI: what PP1V2_S3_REG_R is and how to check itPP1V2_S3_REG_R is a 1.2 V rail in the S3 (memory) startup stage, judging from its name; the board data has no parts list, so which components sit on it isn't known. Known-good readings are diode 0.223 to ground, 1.200 V with power applied, and 221.000 ohms to ground. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and the rail enabled. A diode or resistance far below known-good usually points to a short or a leaky part on the rail, while a missing voltage with a normal diode reading points upstream to its enable or regulator. These are community readings and only a guide, so compare against a matching rail or a known-good board before condemning anything. | |||
PP1V05_S3 | 0.219 | – | – |
AI: what PP1V05_S3 is and how to check itPP1V05_S3 is a 1.05 V rail that, from its name, belongs to the S3 (memory/suspend) stage of the boot sequence. The archive lists one known-good reading: diode 0.219 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and confirm the voltage appears when the sequence reaches PP1V_S3. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.219 usually points to a short or a faulty part on that rail, but confirm with more than one measurement before replacing anything. | |||
PP2V5_S3 | 0.420 | 2.500 | – |
AI: what PP2V5_S3 is and how to check itPP2V5_S3 is a 2.5 V rail that the name places in the S3 (memory) startup stage. The archived readings for this board list diode 0.420 and voltage 2.500, with no condition noted, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well off 2.500 or a diode far from 0.420 usually points to a short or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part. No known-good resistance reading is recorded here. | |||
PPVIN_S3_DDR2V5_RC | 0.420 | – | – |
AI: what PPVIN_S3_DDR2V5_RC is and how to check itPPVIN_S3_DDR2V5_RC — from the name, this is a 2.5 V DDR supply input that comes up in the S3 (memory) stage of the power sequence. The only known-good reading in the archive is a diode value of 0.420 to ground; there is no known-good voltage reading here.
| |||
S0: running 44
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP0V6_S0_DDRVTT | 0.132 | – | – |
AI: what PP0V6_S0_DDRVTT is and how to check itPP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the "S0" in its name marks it as a running-state rail, and "DDRVTT" indicates it terminates the memory bus (this is from the name, not the board data). The archive lists one known-good reading: diode 0.132 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.132 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault. | |||
PP0V75_S0_GPU | 0.050 | 0.750 | 49.300R |
AI: what PP0V75_S0_GPU is and how to check itPP0V75_S0_GPU is a 0.75 V GPU rail that comes up in the S0 (running) state, judged from its name. The archive lists a known-good diode reading of 0.050, voltage 0.750 V and resistance 49.300R; treat these as a community guide, not a spec. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board in S0. A diode or resistance far below known-good suggests a short or leaky load on the rail; a missing 0.75 V with a normal diode reading points upstream to its enable or supply. No known-good waveform or current reading is recorded here. | |||
PP0V85_MEMCI_S0_GPU | 0.089 | 0.850 | 88.400R |
AI: what PP0V85_MEMCI_S0_GPU is and how to check itPP0V85_MEMCI_S0_GPU is a 0.85 V memory-interface rail for the GPU, judged from its name; the S0 suffix means it belongs to the running state. Known-good readings in the archive: diode 0.089, voltage 0.850 V, resistance 88.400R (no condition recorded). With the board unpowered, measure diode mode from the rail to ground and compare with 0.089; then power up and check for about 0.850 V. A far-off diode or resistance reading usually points to a short or a failed part on that rail, but one reading alone doesn't confirm a bad part. No known-good value of another kind is listed here. | |||
PP0V95_S0_CPUVCCIO_REG_R | 0.076 | – | 83.200R |
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check itPP0V95_S0_CPUVCCIO_REG_R is the CPU VCCIO rail, a 0.95 V supply for the CPU's I/O section; the "S0" in the name marks it as a running-state rail, and the "_REG_R" suffix suggests a regulated rail on the right-hand side of a pair. Known-good from the archive: diode 0.076 and resistance 83.200R, with no condition recorded. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied during S0. A reading far from known-good usually points to a short or a failed regulator, but one reading alone doesn't confirm a bad part; compare against the matching net on the other side of the pair before replacing anything. No known-good voltage reading is listed here. | |||
PP1V2_S0SW | 0.303 | – | – |
AI: what PP1V2_S0SW is and how to check itPP1V2_S0SW is a 1.2 V rail that comes up in the S0 (running) state, judging by its name and its place late in the boot sequence after SLP_S3# is de-asserted. The only known-good reading here is a diode value of 0.303 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.303 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything. | |||
PP1V05_S0SW | 0.208 | – | – |
AI: what PP1V05_S0SW is and how to check itPP1V05_S0SW is a 1.05 V rail in the S0 (running) state, judged from its name; the boot sequence lists PP1V_S0SW in the S0SW group, so it belongs to the CPU/SOC power-up stage. The only known-good reading here is diode 0.208 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.208 can suggest a short or an open on that net, but one reading alone doesn't prove a part bad; compare with a matching rail on a known-good board before replacing anything. | |||
PP1V8_S0_GPU | 0.190 | – | – |
AI: what PP1V8_S0_GPU is and how to check itPP1V8_S0_GPU is a 1.8 V GPU rail that comes up in the S0 (running) state, judging from its name. The only known-good figure in the archive is a diode reading of 0.190 to ground; there is no known-good voltage or resistance value for it. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.190 usually points to a short or a damaged load on the rail; a far higher or open reading points to a broken connection. Confirm with a voltage measurement before suspecting any part, since one reading alone isn't proof. | |||
PP1V8_S0_GPU_CONN | OL | – | – |
AI: what PP1V8_S0_GPU_CONN is and how to check itPP1V8_S0_GPU_CONN is a 1.8 V rail, from its name: an S0 (running-state) supply for the GPU connector area. The only archived reading is a diode value of OL, with no condition recorded, and there is no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage; compare against a matching 1.8 V S0 rail if one is available. A far-off diode reading or a missing voltage usually points to a short, an open feed, or the rail not being enabled, but one reading alone doesn't confirm a bad part. | |||
PP1V8_S0_GPU_REG | 0.200 | 1.800 | 0.001R |
AI: what PP1V8_S0_GPU_REG is and how to check itReference note for PP1V8_S0_GPU_REG on the 820-01700:
| |||
PP1V8_S0_PCH_VCCHDA_F | 0.363 | – | 0.019R |
AI: what PP1V8_S0_PCH_VCCHDA_F is and how to check itPP1V8_S0_PCH_VCCHDA_F — a 1.8 V rail, from the name: the PCH's HDA (audio codec) supply, in the S0 (running) state. Known-good from the readings archive: diode 0.363 and resistance 0.019R; no known-good voltage is recorded here.
| |||
PP1V35_MEMIO_S0_GPU | 0.048 | 1.350 | 46.600R |
AI: what PP1V35_MEMIO_S0_GPU is and how to check itPP1V35_MEMIO_S0_GPU is a 1.35 V memory-interface rail for the GPU; the "S0" in the name means it belongs to the running (S0) state, and this is from the name rather than a schematic. Known-good readings in the archive: diode 0.048, voltage 1.350 V, resistance 46.600R — treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and in S0. A reading far from known-good (a short or very low diode value, or the rail missing or pulled down) usually points to a shorted load or a failed supply, but one reading alone doesn't confirm a bad part. No known-good reading of other kinds is listed here. | |||
PP3V3_S0_GPU | 0.416 | – | – |
AI: what PP3V3_S0_GPU is and how to check itPP3V3_S0_GPU is a 3.3 V GPU rail that comes up in the S0 (running) state, based on its name. The archive lists one known-good reading: diode mode to ground 0.416, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied and the board in S0. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below 0.416 usually points to a short or a failing load on the rail; far above can mean an open path — treat either as a lead, not a verdict. | |||
PP3V3_S0SW_LCD | 0.484 | 3.300 | – |
AI: what PP3V3_S0SW_LCD is and how to check itPP3V3_S0SW_LCD is a switched 3.3 V LCD rail; the name indicates an S0 (running) state, software-switched supply for the display. Known-good readings from the archive: diode 0.484 to ground and 3.300 V with the board powered in S0. Check it unpowered in diode mode to ground first, then measure the voltage with power applied and the board booted to S0. A diode reading far from 0.484 suggests a short or leak on the rail or its load; a missing 3.300 V with a normal diode reading points upstream to the switch or enable. No known-good resistance reading is available here, and these values are community guides that vary with board state. | |||
PP3V3_S0SW_LCD_R | 0.485 | – | – |
AI: what PP3V3_S0SW_LCD_R is and how to check itPP3V3_S0SW_LCD_R is a switched 3.3 V LCD rail; the "_S0SW" part of the name indicates it comes up in the S0 (running) state, and "_LCD_R" suggests it feeds the right-side LCD circuitry. The only known-good figure here is a diode reading of 0.485 to ground, with no condition noted; there is no known-good voltage reading for this rail.
| |||
PP3V3_S0SW_TBT_T | 0.537 | – | – |
AI: what PP3V3_S0SW_TBT_T is and how to check itPP3V3_S0SW_TBT_T is a 3.3 V switched S0 rail, most likely for Thunderbolt circuitry — that reading is from the name, not the board data. The archive lists a known-good diode reading of 0.537 to ground; no known-good voltage reading here. Check it unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied once the board reaches S0. A diode reading far from 0.537 usually points to a short or a damaged part on that rail, but one reading alone isn't proof — compare with a matching rail before replacing anything. | |||
PP3V3_S0SW_TBT_T_SNS | 0.500 | 3.300 | – |
AI: what PP3V3_S0SW_TBT_T_SNS is and how to check itPP3V3_S0SW_TBT_T_SNS — reference note
| |||
PP3V3_S0SW_TBT_X | 0.532 | – | – |
AI: what PP3V3_S0SW_TBT_X is and how to check itPP3V3_S0SW_TBT_X is a 3.3 V switched rail for the Thunderbolt section, in the S0 (running) state — that reading comes from the rail's name, not from a schematic. The archive lists one known-good value: diode 0.532 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail; compare the diode reading with that 0.532 guide. A diode reading far below it usually points to a short or a leaky part on the rail, while a far higher or open reading points to a missing connection or an unpopulated path. The voltage itself has no known-good figure here, so compare it against a matching rail on a known-good board rather than judging it alone. | |||
PP3V3_S0SW_TBT_X_SNS | 0.532 | – | – |
AI: what PP3V3_S0SW_TBT_X_SNS is and how to check itPP3V3_S0SW_TBT_X_SNS is a 3.3 V S0 (running-state) switched sense rail tied to the Thunderbolt section, judging from its name. The archive lists one known-good reading: diode 0.532 to ground, with no stated condition. With the board unpowered, measure diode mode from the net to ground and compare; then power up and check the voltage, which should sit near 3.3 V once the board is in S0. No known-good voltage reading is recorded here, so treat the diode value as a guide only. A reading far from 0.532 in diode mode usually points to a short or an open on that net rather than a confirmed bad part, so recheck before replacing anything. | |||
PP5V_S0_ALSCAM_F | 0.404 | 5.000 | – |
AI: what PP5V_S0_ALSCAM_F is and how to check itPP5V_S0_ALSCAM_F is a 5 V rail that, judging by its name, supplies the ALS/camera circuit and comes up at the S0 (running) stage. The known-good readings for this board are diode 0.404 to ground and 5.000 V when powered. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.404 usually points to a short or a damaged component on that rail; a missing 5 V with a normal diode reading points upstream at its enable or source. These are community readings and only a guide, and no resistance value is recorded here. | |||
PP5V_S0SW_LCD | 0.570 | 5.000 | – |
AI: what PP5V_S0SW_LCD is and how to check itPP5V_S0SW_LCD is a 5 V LCD-related rail that comes up in the S0 (running) state, judging by its name. The archive lists a known-good diode reading of 0.570 and a voltage of 5.000; no condition is recorded for either, so treat them as a guide only.
A diode reading far below 0.570 usually points to a short or a leaky load on the rail; a voltage well under 5.000 with a normal diode reading suggests the rail isn't being enabled or is loaded down. No known-good resistance reading exists for this rail. | |||
PPGFX_S0_GPU | 0.016 | 0.900 | 14.800R |
AI: what PPGFX_S0_GPU is and how to check itPPGFX_S0_GPU is a GPU power rail that runs in the S0 (running) state, judging by its name; the board data doesn't list which parts sit on it. Known-good readings from the community archive: diode 0.016, voltage 0.900 V, resistance 14.800R — treat these as a guide, since readings vary with board state. To check it, power the board off and measure diode mode to ground, then apply power and measure the voltage. A diode or resistance far from known-good (especially near zero) usually points to a short on the rail, but confirm with a second measurement before replacing anything. No known-good value of any other kind is listed here. | |||
PPGFX_S0_GPU_R1 | 0.016 | 0.900 | 14.800R |
AI: what PPGFX_S0_GPU_R1 is and how to check itPPGFX_S0_GPU_R1 — reference note
| |||
PPGFX_S0_GPU_R2 | 0.016 | 0.900 | 14.800R |
AI: what PPGFX_S0_GPU_R2 is and how to check itPPGFX_S0_GPU_R2 is a GPU power rail in the S0 (running) state, judging from the name: GFX for graphics, S0 for the running stage. The archive lists a known-good diode reading of 0.016, voltage 0.900, and resistance 14.800R; treat these as a community guide, not a factory spec.
A single reading isn't proof a part is bad, so compare with a matching rail or a known-good board before replacing anything. | |||
PPGFX_S0_GPU_R3 | 0.016 | 0.900 | 14.800R |
AI: what PPGFX_S0_GPU_R3 is and how to check itPPGFX_S0_GPU_R3 is a GPU power rail that comes up in the S0 running state, judging by its name (the S0 suffix is from the name; the "GFX" part suggests graphics). The archive lists diode 0.016, voltage 0.900 V and resistance 14.800R for it, with no condition noted, so treat these as a guide only.
There is no known-good reading here for other conditions, so compare against a matching rail on a known-good board where possible. | |||
PPGFX_S0_GPU_R4 | 0.016 | 0.900 | 14.800R |
AI: what PPGFX_S0_GPU_R4 is and how to check it
| |||
PPGFX_S0_GPU_SW1 | 0.016 | 0.900 | – |
AI: what PPGFX_S0_GPU_SW1 is and how to check itPPGFX_S0_GPU_SW1 — the name indicates a graphics (GPU) supply rail switched in the S0 (running) state, so it should only be present once the board is fully on. Known-good readings in the archive: diode 0.016 and voltage 0.900 V; no condition is recorded, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.016 usually points to a short or a leaky part on that rail, while a missing or low voltage with a normal diode reading points upstream at the GPU power stage or its enable. No known-good resistance reading exists for this rail. | |||
PPGFX_S0_GPU_SW2 | 0.016 | 0.900 | – |
AI: what PPGFX_S0_GPU_SW2 is and how to check itPPGFX_S0_GPU_SW2 is a GPU graphics rail: the "PP" prefix means a power rail, "GFX" points to the GPU, "S0" means the running state (from the name), and "SW2" suggests a second switched supply. The archive lists it as diode 0.016 and 0.900 V, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode reading far below 0.016 suggests a short on the rail; a voltage far from 0.900 V points to the supply not switching on or a load pulling it down. No other known-good values are recorded here, so compare against a matching rail or a known-good board. | |||
PPGFX_S0_GPU_SW3 | 0.016 | 0.900 | – |
AI: what PPGFX_S0_GPU_SW3 is and how to check itPPGFX_S0_GPU_SW3 — the name indicates a GPU graphics power rail (PPGFX), active in the S0 running state, from a switched supply (SW3). This is from the name only; the archive has no schematic detail for this net.
| |||
PPGFX_S0_GPU_SW4 | 0.016 | 0.900 | – |
AI: what PPGFX_S0_GPU_SW4 is and how to check itPPGFX_S0_GPU_SW4 is a GPU graphics power rail; the S0 in the name indicates the running state, and SW4 suggests a switched rail (general reading of the name, not from board data). Known-good readings here are diode 0.016 and voltage 0.900. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.016 suggests a short or leaky load on the rail; a voltage far from 0.900 with power applied points to the rail not switching on or being pulled down. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault. | |||
PPSOC_S0_GPU | 0.007 | 0.900 | 7.400R |
AI: what PPSOC_S0_GPU is and how to check itPPSOC_S0_GPU is a GPU power rail, and the S0 in its name indicates it belongs to the running (S0) state. The archive lists it as diode 0.007, voltage 0.900 and resistance 7.400R, with no condition noted, so treat these as a guide only.
No known-good reading of another kind is listed here. | |||
PPSOC_S0_GPU_R | 0.007 | 0.900 | 4.000R |
AI: what PPSOC_S0_GPU_R is and how to check itPPSOC_S0_GPU_R is a running-state (S0, from the name) GPU power rail on this board. The archive lists a known-good diode reading of 0.007 to ground, a voltage of 0.900, and a resistance of 4.000R; treat these as a community guide, not a spec.
| |||
PPSOC_S0_GPU_SW | 0.007 | – | 4.000R |
AI: what PPSOC_S0_GPU_SW is and how to check itPPSOC_S0_GPU_SW is a GPU power-switch rail in the S0 (running) state, judged from the name; the archive doesn't list which parts sit on it. Known-good readings here are diode 0.007 and resistance 4.000R, with no condition recorded, so treat them as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from 0.007/4.000R usually points to a short or a failed switch/load on that rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is recorded for this rail. | |||
PPVCC_S0_CPU | 0.002 | 1.500 | 2.400R |
AI: what PPVCC_S0_CPU is and how to check itPPVCC_S0_CPU is the CPU core power rail; the S0 in its name indicates it belongs to the running (S0) state. The archive lists diode 0.002, voltage 1.500 and resistance 2.400R, but no condition is recorded, so treat these as a rough guide only. With the board unpowered, measure diode mode from the rail to ground and compare with 0.002; then power up and check the voltage against 1.500. A diode reading far from 0.002 usually points to a short or a failed component on the rail, but a single reading isn't proof, so confirm with resistance and a second measurement before replacing anything. No known-good reading here covers other board states. | |||
PPVCCGT_S0_CPU | 0.010 | 1.500 | 9.500R |
AI: what PPVCCGT_S0_CPU is and how to check itPPVCCGT_S0_CPU is a CPU graphics rail; the S0 in the name indicates it is up in the running state. The archive lists a diode reading of 0.010, a voltage of 1.500 and a resistance of 9.500R, but no condition is recorded, so treat these as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from these usually points to a short or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything. | |||
PPVCCIO_S0_CPU | 0.076 | 0.950 | 75.000R |
AI: what PPVCCIO_S0_CPU is and how to check itReference note for PPVCCIO_S0_CPU (820-01700):
| |||
PPVCCSA_S0_CPU | 0.033 | 1.150 | 21.400R |
AI: what PPVCCSA_S0_CPU is and how to check itPPVCCSA_S0_CPU is a running-state (S0, from the name) CPU supply rail, most likely the CPU system-agent voltage — that's general inference from the name, not from board data. Known-good readings in the archive: diode 0.033, voltage 1.150 V, resistance 21.400R; no condition is recorded with them, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode or resistance far below known-good usually points to a short or a failing load on the rail, while a missing voltage with a normal diode reading points upstream to its enable or supply — confirm with the next rail in the sequence before replacing anything. | |||
PPVIN_S0_CPUVR_VIN | 0.422 | – | – |
AI: what PPVIN_S0_CPUVR_VIN is and how to check itPPVIN_S0_CPUVR_VIN — reference note
| |||
PPVIN_S0SW_LCDBKLT | 0.833 | 12.600 | – |
AI: what PPVIN_S0SW_LCDBKLT is and how to check itPPVIN_S0SW_LCDBKLT is the LCD backlight input rail, and the S0SW in its name indicates it belongs to the running (S0) state. The archive lists a known-good diode reading of 0.833 to ground and a voltage of 12.600, with no condition noted, so treat these as a guide only.
No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board if needed. | |||
PPVIN_S0SW_LCDBKLT_FET | 0.415 | 12.600 | 410.000 |
AI: what PPVIN_S0SW_LCDBKLT_FET is and how to check itPPVIN_S0SW_LCDBKLT_FET is the switched input feed to the LCD backlight circuit, active in the S0 (running) state — that stage comes from the name. Known-good community readings here are diode 0.415, voltage 12.600 and resistance 410.000; treat them as a guide, since they vary with board state. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode or resistance far below known-good usually points to a short or leaky part on that net, while a missing 12.6 V with power applied points upstream to the backlight enable/switch path; no known-good value exists for other conditions. | |||
PPVIN_S0SW_LCDBKLT_R | 0.415 | 12.600 | – |
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check itPPVIN_S0SW_LCDBKLT_R is the backlight input rail for the LCD, from its name: an S0 (running-state) switch rail feeding the display backlight. Known-good readings in the archive are diode 0.415 and voltage 12.600; treat these as a guide, since community readings vary with board state.
One reading alone doesn't confirm a bad part; check the feed and enable side before replacing anything. | |||
PPVOUT_S0_KBDLED | 0.601 | – | – |
AI: what PPVOUT_S0_KBDLED is and how to check itPPVOUT_S0_KBDLED is the keyboard backlight output rail; the S0 in the name indicates it belongs to the running (S0) power state. The only known-good figure here is a diode reading of 0.601 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode reading far below 0.601 usually points to a short or a leaky component on the rail, while a much higher reading can mean an open path; treat a single reading as a guide only and compare against a matching net or a known-good board before condemning anything. | |||
PPVOUT_S0_KBDLED_R | 0.608 | 40.000 | – |
AI: what PPVOUT_S0_KBDLED_R is and how to check itPPVOUT_S0_KBDLED_R is a keyboard backlight output rail; the S0 in the name indicates it belongs to the running (S0) state, and the name itself is the only description available here. The archive lists a known-good diode reading of 0.608 and a voltage of 40.000, with no condition noted, so treat both as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far below 0.608 usually points to a short or a leaky component on the rail; a far higher or open reading points to a broken connection. No known-good resistance value is recorded for this rail. | |||
PPVOUT_S0_LCDBKLT | 1.148 | 55.000 | – |
AI: what PPVOUT_S0_LCDBKLT is and how to check itPPVOUT_S0_LCDBKLT — backlight boost output (S0 = running stage, from the name).
| |||
PPVOUT_S0_LCDBKLT_F | 1.181 | 59.000 | 0.177R |
AI: what PPVOUT_S0_LCDBKLT_F is and how to check itPPVOUT_S0_LCDBKLT_F is the LCD backlight output rail; the "S0" in the name marks it as a running-state rail. Known-good readings here are diode 1.181, voltage 59.000 and resistance 0.177R — treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and the display connected. A reading far from known-good usually points to a fault on the backlight output or its load rather than proof of a bad part; a small difference can be normal. | |||
Repair notes
Power
Boot sequence
* Valid external PSU, bat or charger
PBUS
PP3V3_G3H_RTC
PP3V3_G3H
VIN_RTC > VIN_RTC_UPPER_THRESHOLD
PP1V8_SLPS2R
PMU_CLK32K_SOC
PP1V8_AWAKE
PP1V8_SLPS2R_PMUGPIO
PP1V1_SLPS2R
PP0V8_SLPS2R
PP0V82_SLPDDR
PP3V3_AWAKE
PPVDDCPUSRAM_AWAKE
PP0V9_SLPDDR
PP1V1_SLPDDR_SOCFET_EN
PP1V1_SLPDDR
H9M_24MHz_CLK
PP1V2_AWAKE
PPVDDCPU_AWAKE
PMU_SYS_ALIVE
PMU_ACTIVE_READY
PMU_COLD_RESET_L
H9M LOAD SECURE ROM, SMC BATTERY TRAP
PMU_PVDDMAIN_EN
P3V3MAIN_PGOOD
PP3V_G3H_RTC
PMU_CLK32K_PCH
PCH_RTC_RESET_L
P5VG3S_EN
PP5V_G3S
P3V3G3S_EN
PP3V3_G3S
P1V8G3S_EN
PP1V8_G3S
P5VG3S_PGOOD
PMU_CLK32K_WLANBT
SSD 4LANDING: OCARINA I2C WRITE POWER_STATE_TARGET=ACTIVE TO ENABLE SSD POEWR
SSD_PMU_RESET_L
PPVCCQ_ANI_SSD0
PP0V9_SSD0
SSD0_VR_2V5_EN
PP2V5_NAND_SSD0
SSD0_OCARINA_WP_L
SSD0_OCARINA_PFN
SSD0_PCARINA_RESET_L
SSD 2LANDING: CALPE, CONFIGURE RAILS AND GPIOS TO ENABLE SSD POWER
PPVCCQ_ANI_SSD0
PP0V9_SSD0
SSD0_PMIC_DISCHARGE_EN
SSD0_VR_2V5_EN
PP2V5_NAND_SSD0
SSD0_VR_P2V5_PGOOD
SSD0_PMIC_RESET_L
SSD BEGINS POWER BUTTON MONITORING
PMU_ONOFF_L
PP3V3_S5
PP1V8_S5
PPVPCORE_S5
PP1V_PRIM
SMC_RSMRST_L
PM_RSMRST_L
SMC WAITS FOR eSPI_RESET# PIN
PCH_PWRBTN_L
PP1V8_S3
PVDDQ_EN
PP1V2_S3
PVDDQ_PGOOD
PP1V_S3
PCH DE-ASSERTS SLP_S3#, SLP_A#, SLP_LAN#, and SLP_WLAN# over eSPI
PVCCPLLOC_EN
PP1V2_S0SW
PP1V_S0SW
PVCCIO_EN
PVCCIO
PVCCIO_PGOOD
ALL_SYS_PWRGD
CPU_VR_READY
PM_SYSRST_L
PM_PCH_PWROK
PM_PCH_SYS_PWROK
DONE.
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
5VG3S_VFB1_RR | 0.600 | – | – |
50_0_ANT | 0.000 | – | – |
50_1_ANT | 0.000 | – | – |
50_2_ANT | 0.000 | – | – |
ACT_GND | 0.544 | – | – |
ADC1_REFCOMP | OL | – | – |
ADC2_REFCOMP | OL | – | – |
AGND_P2V5S3 | 0.000 | – | – |
AGND_PVDD18GPU | 0.000 | – | – |
AGND_PVDD075GPU | 0.000 | – | – |
ALL_SYS_PWRGD | 0.516 | – | – |
ANGLE_SENSOR_MGL | 0.541 | – | – |
ANGLE_SENSOR_ND | 0.539 | – | – |
AUD_CONN_HP_LEFT | 0.703 | – | – |
AUD_CONN_HP_RIGHT | 0.707 | – | – |
AUD_CONN_HP_SENSE_L | 1.329 | – | – |
AUD_CONN_HP_SENSE_R | 1.328 | – | – |
AUD_CONN_RING_SENSE | OL | – | – |
AUD_CONN_RING2 | 0.000 | – | – |
AUD_CONN_RING2_XW | 0.632 | – | – |
AUD_CONN_SLEEVE | 0.000 | – | – |
AUD_CONN_SLEEVE_XW | 0.631 | – | – |
AUD_CONN_TIP_SENSE | OL | – | – |
AUD_DMIC0_CLK_CONN | 0.515 | – | – |
AUD_DMIC0_DATA_CONN | 0.554 | – | – |
AUD_DMIC1_CLK_CONN | 0.514 | – | – |
AUD_DMIC1_DATA_CONN | 0.546 | – | – |
AUD_HP_PORT_CH_GND | 0.000 | – | – |
AUD_HP_PORT_L | 0.703 | – | – |
AUD_HP_PORT_R | 0.707 | – | – |
AUD_HP_PORT_US_GND | 0.000 | – | – |
AUD_HP_SENSE_L | 1.329 | – | – |
AUD_HP_SENSE_R | 1.328 | – | – |
AUD_HS_MIC_N | 0.632 | – | – |
AUD_HS_MIC_P | 0.631 | – | – |
AUD_RING_SENSE | 0.644 | – | – |
AUD_TIP_SENSE | 1.420 | – | – |
BKLT_EN_R | 0.528 | – | – |
BKLT_ISET_KEYB | 0.680 | – | – |
BKLT_KEYB1 | 0.659 | – | – |
BKLT_KEYB2 | 0.653 | – | – |
BKLT_PWM_KEYB_3V3 | 0.546 | – | – |
BKLT_PWM_MLB2TCON | OL | – | – |
BKLT_SCL | 0.539 | – | – |
BKLT_SD | 0.597 | – | – |
BKLT_SDA | 0.539 | – | – |
BKLT_SENSE_OUT | 0.734 | – | – |
BT_AUDIO_SYNC | 0.637 | – | – |
BT_AUDIO_SYNC_LS3V3 | 0.620 | – | – |
BT_SFLASH_CS_L | 0.692 | – | – |
BT_SFLASH_HOLD_L | 0.665 | – | – |
BT_SFLASH_WP_L | 0.666 | – | – |
BT_SPI2_CLK | 0.681 | – | – |
BT_SPI2_CSN | 0.717 | – | – |
BT_SPI2_MISO | 0.640 | – | – |
BT_SPI2_MOSI | 0.645 | – | – |
CAPSLOCK_LED_DRV | 0.755 | – | – |
CAPSLOCK_LED_EN | 0.509 | – | – |
CHGR_AMON | 0.598 | 0.300 | – |
CHGR_AUX_DET | 0.634 | – | – |
CHGR_BGATE | 0.632 | – | – |
CHGR_BMON | 0.605 | – | – |
CHGR_BOOT1 | 0.692 | – | – |
CHGR_BOOT1_RC | 0.592 | – | – |
CHGR_BOOT2 | 0.588 | – | – |
CHGR_BOOT2_RC | 0.588 | – | – |
CHGR_COMP | 0.632 | – | – |
CHGR_CSI_N | 0.552 | – | – |
CHGR_CSI_P | 0.552 | – | – |
CHGR_CSI_R_N | 0.552 | – | – |
CHGR_CSI_R_P | 0.552 | – | – |
CHGR_CSO_N | 0.416 | – | – |
CHGR_CSO_P | 0.417 | – | – |
CHGR_CSO_R_N | 0.415 | 12.600 | 410.000 |
CHGR_CSO_R_P | 0.415 | 12.600 | 410.000 |
CHGR_EN_MVR | 0.609 | 5.000 | – |
CHGR_EN_MVR_R | 0.612 | – | – |
CHGR_GATE_Q1 | 0.730 | – | – |
CHGR_GATE_Q2 | 0.455 | – | – |
CHGR_GATE_Q3 | 0.462 | – | – |
CHGR_GATE_Q4 | 0.720 | – | – |
CHGR_INT_L | 0.590 | 1.800 | – |
CHGR_LX1 | 0.505 | – | – |
CHGR_LX2 | 0.506 | – | – |
CHGR_PBUS_SENSE | 0.415 | – | – |
CHGR_PHASE1 | 0.507 | 12.600 | 305.700R |
CHGR_PHASE2 | 0.507 | 12.600 | – |
CHGR_RST_IN | 0.625 | – | – |
CHGR_RST_IN_R | 0.610 | – | – |
CHGR_VBAT | 0.636 | – | – |
CHGR_VDDA | 0.459 | 5.000 | – |
CHGR_VDDP | 0.456 | 5.000 | – |
CODEC_INT_L | 0.494 | – | – |
CODEC_RESET_L | 0.497 | – | – |
CODEC_WAKE_L | 0.492 | – | – |
COMP_A_CPUCORE | 0.626 | – | – |
COMP_A_CPUCORE_L | OL | – | – |
COMP_B_CPUGT | 0.627 | – | – |
COMP_B_CPUGT_L | OL | – | – |
COMP_C_CPUSA | 0.626 | – | – |
COMP_C_CPUSA_L | OL | – | – |
CORE_ISUMN_R | 1.015 | – | – |
CPU_C10_GATE_L | 0.484 | – | – |
CPU_CATERR_L | 0.232 | – | – |
CPU_CFG_RCOMP | 0.052 | – | 50.400R |
CPU_CFG<0> | 0.284 | – | – |
CPU_CFG<1> | 0.285 | – | – |
CPU_CFG<2> | 0.285 | – | – |
CPU_CFG<3> | 0.284 | – | – |
CPU_CFG<4> | 0.271 | – | – |
CPU_CFG<5> | 0.270 | – | – |
CPU_CFG<6> | 0.271 | – | – |
CPU_CFG<7> | 0.284 | – | – |
CPU_CFG<8> | 0.284 | – | – |
CPU_CFG<9> | 0.285 | – | – |
CPU_CFG<10> | 0.285 | – | – |
CPU_CFG<11> | 0.287 | – | – |
CPU_CFG<12> | 0.284 | – | – |
CPU_CFG<13> | 0.284 | – | – |
CPU_CFG<14> | 0.285 | – | – |
CPU_CFG<15> | 0.287 | – | – |
CPU_CFG<17> | 0.288 | – | – |
CPU_CFG<19> | 0.285 | – | – |
CPU_DC_B2_C1 | OL | – | – |
CPU_DC_B38_C38 | OL | – | – |
CPU_DC_BR1_BR2 | 0.345 | – | – |
CPU_DC_BR2_BR1 | OL | – | – |
CPU_DC_C1_B2 | OL | – | – |
CPU_DC_C38_B38 | OL | – | – |
CPU_EDP_RCOMP | 0.095 | – | – |
CPU_PCH_PM_DOWN | 0.289 | – | – |
CPU_PCH_PM_DOWN_R | 0.277 | – | – |
CPU_PECI | 0.369 | – | – |
CPU_PEG_RCOMP | 0.093 | – | – |
CPU_PROCHOT_L | 0.464 | – | – |
CPU_PROCHOT_OUT_L | 0.466 | – | – |
CPU_PROCHOT_R_L | 0.280 | – | – |
CPU_PWRGD | 0.323 | – | – |
CPU_SM_RCOMP<0> | 0.122 | – | – |
CPU_SM_RCOMP<1> | 0.123 | – | – |
CPU_SM_RCOMP<2> | 0.102 | – | – |
CPU_VCCGTSENSE_N | 0.004 | – | 2.700R |
CPU_VCCGTSENSE_P | 0.007 | – | 7.700R |
CPU_VCCIOSENSE_P | 0.061 | – | 60.000R |
CPU_VCCIOSENSENEG_R | 0.005 | – | 5.100R |
CPU_VCCIOSENSEPOS_R | 0.135 | – | – |
CPU_VCCSASENSE_N | 0.005 | – | 3.200R |
CPU_VCCSASENSE_P | 0.024 | – | 23.200R |
CPU_VCCSENSE_N | 0.004 | – | 3.100R |
CPU_VCCSENSE_P | 0.006 | – | 5.500R |
CPU_VCCST_PWRGD | 0.532 | – | – |
CPU_VIDALERT_L | 0.650 | – | – |
CPU_VIDALERT_R_L | 0.870 | – | – |
CPU_VIDSCLK | 0.229 | – | – |
CPU_VIDSCLK_R | 0.230 | – | – |
CPU_VIDSOUT | 0.230 | – | – |
CPU_VIDSOUT_R | 0.230 | – | – |
CPU_VR_EN_R | 0.532 | – | – |
CPUCORE_ISEN1 | 0.627 | – | – |
CPUCORE_ISEN2 | 0.627 | – | – |
CPUCORE_ISEN3 | 0.628 | – | – |
CPUCORE_ISNS1_N | 0.002 | 1.500 | 2.400R |
CPUCORE_ISNS1_P | 0.002 | 1.500 | 2.400R |
CPUCORE_ISNS2_N | 0.002 | 1.500 | 2.400R |
CPUCORE_ISNS2_P | 0.002 | 1.500 | 2.400R |
CPUCORE_ISNS3_N | 0.002 | 1.500 | 2.400R |
CPUCORE_ISNS3_P | 0.002 | 1.500 | 2.400R |
CPUCORE_ISUMN | 0.004 | – | 3.800R |
CPUCORE_ISUMN_R | 0.442 | – | – |
CPUCORE_ISUMP | 0.340 | – | – |
CPUCORE_PROCHOT_R_L | 0.522 | – | – |
CPUCORE_PSYS | 0.624 | – | – |
CPUCORE_SW1 | 0.002 | 1.500 | 2.400R |
CPUCORE_SW2 | 0.002 | 1.500 | 2.400R |
CPUCORE_SW3 | 0.002 | 1.500 | 2.400R |
CPUCORE_VIDALERT_R_L | 0.277 | – | – |
CPUCORE_VIDSCLK_R | 0.281 | – | – |
CPUCORE_VIDSOUT_R | 0.242 | – | – |
CPUGT_ISEN1 | 0.627 | – | – |
CPUGT_ISEN2 | 0.627 | – | – |
CPUGT_ISNS_N | OL | – | – |
CPUGT_ISNS_P | OL | – | – |
CPUGT_ISNS_R_N | OL | – | – |
CPUGT_ISNS_R_P | OL | – | – |
CPUGT_ISNS1_N | 0.010 | 1.500 | 9.500R |
CPUGT_ISNS1_P | 0.010 | 1.500 | 9.500R |
CPUGT_ISNS2_N | 0.010 | 1.500 | 9.500R |
CPUGT_ISNS2_P | 0.010 | 1.500 | 9.500R |
CPUGT_ISUM_IOUT | OL | – | – |
CPUGT_ISUMN | 0.007 | – | 6.700R |
CPUGT_ISUMN_R | 0.341 | – | – |
CPUGT_ISUMP | 0.480 | – | – |
CPUGT_SW1 | 0.010 | – | 9.500R |
CPUGT_SW2 | 0.010 | 1.500 | 9.500R |
CPUSA_ISNS_N | 0.033 | 1.150 | 21.400R |
CPUSA_ISNS_P | 0.033 | 1.150 | 21.400R |
CPUSA_ISUMN | 0.022 | – | 21.700R |
CPUSA_ISUMN_R | 0.490 | – | – |
CPUSA_ISUMP | 0.575 | – | – |
CPUVR_ISNS_N | OL | – | – |
CPUVR_ISNS_P | OL | – | – |
CPUVR_ISNS_R_N | OL | – | – |
CPUVR_ISNS_R_P | OL | – | – |
CPUVR_ISUM_IOUT | OL | – | – |
CPUVR_PGOOD | 0.575 | – | – |
CPUVR_SWSA | 0.033 | 1.150 | 21.400R |
CPUVSENSE_IN | 0.007 | – | 5.100R |
DBGLED_C10 | OL | – | – |
DBGLED_GPU | OL | – | – |
DBGLED_GPU_D | OL | – | – |
DBGLED_MEM_OK_D | OL | – | – |
DBGLED_S0I3 | OL | – | – |
DBGLED_S0I3_D | OL | – | – |
DBGLED_S5 | OL | – | – |
DDR2V5_IOUT | OL | – | – |
DDRREG_VTTSNS | 0.134 | – | – |
DFR_DISP_INT | 0.496 | – | – |
DFR_DISP_RESET_L | 0.495 | – | – |
DFR_DISP_TE | 0.496 | – | – |
DFR_DISP_VSYNC | OL | – | – |
DFR_LID_OPEN_L | OL | – | – |
DFR_PWR_EN | 0.494 | – | – |
DFR_PWR_EN_R | 0.564 | – | – |
DFR_TOUCH_CLK32K_RESET_L | 0.470 | – | – |
DFR_TOUCH_INT_L | 0.475 | – | – |
DFR_TOUCH_RESET_L | 0.470 | – | – |
DISP_GCON_INT_L | 0.482 | – | – |
DISP_GCON_RESET_L | 0.682 | – | – |
DISP_GCON_RESET_L_R | 0.681 | – | – |
DP_INT_EG_HPD | 0.384 | – | – |
DP_INT_HPD | 0.656 | – | – |
DP_INT_HPD_R | 0.606 | – | – |
DP_T_SNK1_HPD | 0.581 | – | – |
DP_TA_HPD | 0.559 | – | – |
DP_TB_HPD | 0.561 | – | – |
DP_X_SNK0_HPD | 0.555 | – | – |
DP_X_SNK1_HPD | 0.588 | – | – |
DP_XA_HPD | 0.605 | – | – |
DP_XB_HPD | 0.567 | – | – |
EADC1_CPUSA_VSENSE | OL | – | – |
EADC1_TBT_X_ISENSE | OL | – | – |
EADC2_AD0 | OL | – | – |
EADC2_GPU_MEM_VDDCI_ISENSE | OL | – | – |
EADC2_GPU_MEM_VDDIO_ISENSE | OL | – | – |
EDP_BKLT_EN | 0.530 | – | – |
EDP_INT_AUX_N | 0.694 | – | – |
EDP_INT_AUX_P | 0.694 | – | – |
EDP_INT_ML_N<0> | 0.412 | – | – |
EDP_INT_ML_N<1> | 0.413 | – | – |
EDP_INT_ML_N<2> | 0.416 | – | – |
EDP_INT_ML_N<3> | 0.413 | – | – |
EDP_INT_ML_P<0> | 0.411 | – | – |
EDP_INT_ML_P<1> | 0.411 | – | – |
EDP_INT_ML_P<2> | 0.413 | – | – |
EDP_INT_ML_P<3> | 0.412 | – | – |
EDP_PANEL_PWR_BUF_EN | 0.613 | – | – |
EDP_PANEL_PWR_DLY_EN | 0.706 | – | – |
EDP_PANEL_PWR_EN | 0.537 | – | – |
EG_RESET_L_BUFF | 0.615 | – | – |
EG_VR0_EN | 0.504 | – | – |
EG_VR0_PGOOD | 0.611 | – | – |
EG_VR1_EN | 0.603 | – | – |
EG_VR1_PGOOD | 0.596 | – | – |
EG_VR2_EN | 0.625 | – | – |
EG_VR2_PGOOD | 0.530 | – | – |
EG_VR3_EN | 0.572 | – | – |
EG_VR3_PGOOD | 0.604 | – | – |
EG_VR4_EN | 0.576 | – | – |
EG_VR4_PGOOD | 0.459 | – | – |
FAN_LT_PWM | 0.754 | – | – |
FAN_LT_TACH | OL | – | – |
FAN_RT_PWM | 0.770 | – | – |
FAN_RT_TACH | OL | – | – |
FB_A_CORE_R | 1.616 | – | – |
FB_A_CPUCORE | 0.614 | – | – |
FB_A_CPUCORE_RC | 1.177 | – | – |
FB_B_CPUGT | 0.595 | – | – |
FB_B_CPUGT_RC | 1.162 | – | – |
FB_B_GT_R | OL | – | – |
FB_C_CPUSA | 0.604 | – | – |
FB_C_CPUSA_RC | OL | – | – |
FB_C_SA_R | OL | – | – |
FB_CORE_R | 0.006 | – | 5.200R |
FB_GT_R | 0.009 | – | 7.800R |
FB_SA_R | 0.024 | – | 23.200R |
GFX_THROTTLE_1V8_R_L | 0.485 | – | – |
GFXGPU_SUM_N | 0.760 | – | – |
GFXGPU_SUM_P | 0.760 | – | – |
GFXGPU_SUM_R_N | 0.593 | – | – |
GFXGPU_SUM_R_P | 0.593 | – | – |
GMUX_IOEXP_ADDR_SEL | 0.000 | – | – |
GND | 0.000 | – | – |
GND_5V3V3_AGND | 0.000 | – | – |
GND_BKLT_SGND | 0.000 | – | – |
GND_P3V3G3HRTC_AGND | 0.000 | – | – |
GPU_CLKREQ_L_R | 0.492 | – | – |
GPU_DBREQ_L | 0.433 | – | – |
GPU_GFX_OVERTEMP | 0.404 | – | – |
GPU_GFX_OVERTEMP_R | 0.576 | – | – |
GPU_GPIO_SVC0 | 0.462 | – | – |
GPU_GPIO_SVD0 | 0.458 | – | – |
GPU_GPIO_SVT0 | 0.436 | – | – |
GPU_GPIO_SVT0_R | 0.456 | – | – |
GPU_JTAG_TCK | 0.398 | – | – |
GPU_JTAG_TDI | 0.437 | – | – |
GPU_JTAG_TDO | 0.436 | – | – |
GPU_JTAG_TESTEN | 0.344 | – | – |
GPU_JTAG_TMS | 0.436 | – | – |
GPU_JTAG_TRST_L | 0.468 | – | – |
GPU_PCC_ALERT_L | 0.491 | – | – |
GPU_PCC_COMP_NEG | 0.468 | – | – |
GPU_PCC_COMP_POS | 0.735 | – | – |
GPU_PROCHOT_L | 0.480 | – | – |
GPU_RESET_L | 0.551 | – | – |
GPU_RESET_L_CONN | OL | – | – |
GPU_RESET_L_R | 0.710 | – | – |
GPU_RESET_R_L | 0.553 | – | – |
GPU_VDD_MEM_RTN | 0.005 | – | 3.400R |
GPU_VDDCR_GFX_COMP | 0.626 | – | – |
GPU_VDDCR_GFX_FB | 0.005 | – | 4.800R |
GPU_VDDCR_GFX_FB_PIN | 0.589 | – | – |
GPU_VDDCR_GFX_FB_R | 0.016 | – | 14.900R |
GPU_VDDCR_GFX_FB_R_C | 0.690 | – | – |
GPU_VDDCR_GFX_FCCM | 0.598 | – | – |
GPU_VDDCR_GFX_IMON | 0.627 | – | – |
GPU_VDDCR_GFX_ISEN1 | 0.628 | – | – |
GPU_VDDCR_GFX_ISEN2 | 0.628 | – | – |
GPU_VDDCR_GFX_ISEN3 | 0.628 | – | – |
GPU_VDDCR_GFX_ISEN4 | 0.628 | – | – |
GPU_VDDCR_GFX_ISNS1_N | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS1_P | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS2_N | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS2_P | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS3_N | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS3_P | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS4_N | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISNS4_P | 0.016 | 0.900 | 14.800R |
GPU_VDDCR_GFX_ISUM_N | 0.003 | – | 2.600R |
GPU_VDDCR_GFX_ISUM_N_C | 1.462 | – | – |
GPU_VDDCR_GFX_ISUM_N_R | 0.459 | – | – |
GPU_VDDCR_GFX_ISUM_P | 0.256 | – | – |
GPU_VDDCR_GFX_ISUM_RC | OL | – | – |
GPU_VDDCR_GFX_NTC | 0.005 | – | 5.200R |
GPU_VDDCR_PROG1 | 0.610 | – | – |
GPU_VDDCR_PROG2 | 0.613 | – | – |
GPU_VDDCR_RTN | 0.005 | – | 4.000R |
GPU_VDDCR_RTN_R | 0.004 | – | 3.800R |
GPU_VDDCR_SOC_COMP | 0.628 | – | – |
GPU_VDDCR_SOC_FB | 0.011 | – | 10.600R |
GPU_VDDCR_SOC_FB_PIN | 0.228 | – | – |
GPU_VDDCR_SOC_FB_R | 0.011 | – | 10.900R |
GPU_VDDCR_SOC_FB_R_C | 0.228 | – | – |
GPU_VDDCR_SOC_IMON | 0.628 | – | – |
GPU_VDDCR_SOC_ISNS_N | 0.007 | 0.900 | 7.400R |
GPU_VDDCR_SOC_ISNS_P | 0.007 | 0.900 | 7.400R |
GPU_VDDCR_SOC_ISUM_N | 0.012 | – | 11.400R |
GPU_VDDCR_SOC_ISUM_N_C | 1.518 | – | – |
GPU_VDDCR_SOC_ISUM_N_R | 0.515 | – | – |
GPU_VDDCR_SOC_ISUM_P | 0.576 | – | – |
GPU_VDDCR_SOC_NTC | 0.011 | – | 11.000R |
GPU_VRAM_D_RST_L | 0.394 | – | – |
GPUCOREVSENSE_IN | 0.007 | – | 3.500R |
GPUSOCVSENSE_IN | 0.011 | – | 9.500R |
GT_ISUMN_R | 1.012 | – | – |
HS_3V3_X_IOUT | 0.712 | – | – |
HS_OTHER5V_IOUT | 0.711 | – | – |
HS_P3V3_G3W_SSD0_OUT | 0.723 | – | – |
HS_P3V3_G3W_SSD1_OUT | 0.720 | – | – |
HS_PBUS_MAIN_SSD0_OUT | 0.712 | – | – |
HS_PBUS_MAIN_SSD1_OUT | 0.712 | – | – |
I2C_ALS_SCL | 0.489 | 1.800 | – |
I2C_ALS_SDA | 0.487 | 1.800 | – |
I2C_BKLT_SCL | 0.542 | 5.000 | – |
I2C_BKLT_SDA | 0.542 | 5.000 | – |
I2C_CAM_ISOL_SCL | 0.522 | 1.800 | – |
I2C_CAM_ISOL_SDA | 0.522 | 1.800 | – |
I2C_DFR_SCL_R | 0.477 | – | – |
I2C_DFR_SDA_R | 0.470 | – | – |
I2C_PWR_SCL | 0.491 | – | – |
I2C_PWR_SDA | 0.490 | – | – |
I2C_SEP_SCL | 0.487 | – | – |
I2C_SEP_SDA | 0.483 | – | – |
I2C_SNS_G3S_SCL | 0.484 | – | – |
I2C_SNS_G3S_SDA | 0.483 | – | – |
I2C_SNS0_S0_5V_SCL | OL | – | – |
I2C_SNS0_S0_5V_SDA | OL | – | – |
I2C_SNS0_S0_SCL | 0.488 | – | – |
I2C_SNS0_S0_SDA | 0.488 | – | – |
I2C_SNS1_S0_SCL | 0.460 | – | – |
I2C_SNS1_S0_SDA | 0.459 | – | – |
I2C_SSD_SCL | 0.478 | – | – |
I2C_SSD_SDA | 0.480 | – | – |
I2C_SSD0_SCL | 0.502 | – | – |
I2C_SSD0_SDA | 0.503 | – | – |
I2C_SSD1_SCL | 0.501 | – | – |
I2C_TBT_T_SCL | 0.508 | 3.300 | – |
I2C_TBT_T_SDA | 0.508 | 3.300 | – |
I2C_TBT_TA_INT_L | 0.588 | – | – |
I2C_TBT_TB_INT_L | 0.560 | – | – |
I2C_TBT_X_SCL | 0.517 | – | – |
I2C_TBT_X_SDA | 0.517 | – | – |
I2C_TBT_XA_INT_L | 0.570 | – | – |
I2C_TBT_XB_INT_L | 0.570 | – | – |
I2C_TCON_SCL | 0.493 | 3.300 | – |
I2C_TCON_SDA | 0.492 | 3.300 | – |
I2C_TPAD_CONN_SCL | 0.515 | – | – |
I2C_TPAD_CONN_SDA | 0.514 | – | – |
I2C_UPC_SCL | 0.472 | 1.800 | – |
I2C_UPC_SDA | 0.474 | 1.800 | – |
I2C_UPC_T_SCL2 | 0.462 | 1.800 | – |
I2C_UPC_T_SDA2 | 0.466 | 1.800 | – |
I2C_UPC_TA_DBG_CTL_SCL | 0.560 | – | – |
I2C_UPC_TA_DBG_CTL_SDA | 0.563 | – | – |
I2C_UPC_TB_DBG_CTL_SCL | 0.563 | – | – |
I2C_UPC_TB_DBG_CTL_SDA | 0.563 | – | – |
I2C_UPC_X_SCL2 | 0.468 | 1.800 | – |
I2C_UPC_X_SDA2 | 0.457 | 1.800 | – |
I2C_UPC_XA_DBG_CTL_SCL | 0.598 | – | – |
I2C_UPC_XA_DBG_CTL_SDA | 0.598 | – | – |
I2C_UPC_XB_DBG_CTL_SCL | 0.565 | – | – |
I2C_UPC_XB_DBG_CTL_SDA | 0.564 | – | – |
I2S_CODEC_D2R | 0.484 | – | – |
I2S_SPKRAMP_L_D2R | 0.363 | – | – |
I2S_SPKRAMP_L_D2R_R1 | 0.376 | – | – |
I2S_SPKRAMP_L_D2R_R2 | 0.376 | – | – |
I2S_SPKRAMP_L_D2R_R3 | 0.376 | – | – |
I2S_SPKRAMP_R_D2R | 0.000 | – | – |
I2S_SPKRAMP_R_D2R_R1 | 0.375 | – | – |
I2S_SPKRAMP_R_D2R_R2 | 0.375 | – | – |
I2S_SPKRAMP_R_D2R_R3 | 0.376 | – | – |
I2S_SPKRAMP_R_LRCLK | 0.392 | – | – |
I2S_SPKRAMP_R_LRCLK_R | 0.374 | – | – |
IAPC_OPA_OUT | OL | – | – |
IMON_A_CPUCORE | 0.626 | – | – |
IMON_B_CPUGT | 0.631 | – | – |
IMON_C_CPUSA | 0.627 | – | – |
IOXP_I2C_SCL | 0.693 | – | – |
IOXP_I2C_SDA | 0.660 | – | – |
IOXP1_INT_L | 0.641 | – | – |
IOXP1_RESET_L | 0.748 | – | – |
IOXP2_ADDR | 0.723 | – | – |
IOXP2_INT_L | 0.641 | – | – |
IOXP2_RESET_L | 0.750 | – | – |
IPD_LID_OPEN | 0.638 | – | – |
IPD_LID_OPEN_R | OL | – | – |
ISNS_1V0_N | OL | – | – |
ISNS_1V0_P | OL | – | – |
ISNS_2V5_S3_N | OL | – | – |
ISNS_2V5_S3_P | OL | – | – |
ISNS_CALPE_IOUT | 0.714 | – | – |
ISNS_CALPE_N | 0.378 | – | – |
ISNS_CALPE_P | 0.378 | – | – |
ISNS_CPUDDR_IOUT | OL | – | – |
ISNS_CPUDDR_N | 0.223 | 1.200 | 221.000 |
ISNS_CPUDDR_P | 0.223 | 1.200 | 221.000 |
ISNS_CPUVCCIO_NEG | 0.496 | – | – |
ISNS_CPUVCCIO_POS | 0.495 | – | – |
ISNS_CPUVDDQ_N | OL | – | – |
ISNS_CPUVDDQ_P | OL | – | – |
ISNS_DDR_IOUT | 0.714 | – | – |
ISNS_GPU_1V8_N | OL | – | – |
ISNS_GPU_1V8_P | OL | – | – |
ISNS_GPU_HS_IOUT | 0.713 | – | – |
ISNS_GPU_HS_N | 0.415 | – | – |
ISNS_GPU_HS_P | 0.415 | – | – |
ISNS_GPU_SOC_IOUT | OL | – | – |
ISNS_GPU1V8_IOUT | OL | – | – |
ISNS_GPUGFX_IOUT | OL | – | – |
ISNS_HS_3V3_T_N | 0.415 | 12.600 | 410.000 |
ISNS_HS_3V3_T_OUT | 0.711 | – | – |
ISNS_HS_3V3_T_P | 0.415 | 12.600 | 410.000 |
ISNS_HS_3V3_X_N | 0.415 | – | 410.000 |
ISNS_HS_3V3_X_P | 0.415 | – | 410.000 |
ISNS_HS_COMPUTING_N | 0.415 | 12.600 | 410.000 |
ISNS_HS_COMPUTING_OUT | 0.714 | – | – |
ISNS_HS_COMPUTING_P | 0.415 | 12.600 | 410.000 |
ISNS_HS_OTHER5V_N | 0.415 | 12.600 | 0.200R |
ISNS_HS_OTHER5V_P | 0.415 | 12.600 | 0.000R |
ISNS_KBDLED_IOUT | OL | – | – |
ISNS_KBDLED_N | OL | – | – |
ISNS_KBDLED_P | OL | – | – |
ISNS_LCDBKLT_IOUT | OL | – | – |
ISNS_LCDBKLT_N | 0.415 | 12.600 | – |
ISNS_LCDBKLT_P | 0.415 | 12.600 | – |
ISNS_LCDPANEL_IOUT | OL | – | – |
ISNS_LCDPANEL_N | OL | – | – |
ISNS_LCDPANEL_P | OL | – | – |
ISNS_P3V3_G3W_SSD0_N | 0.421 | – | – |
ISNS_P3V3_G3W_SSD0_P | 0.421 | – | – |
ISNS_P3V3_G3W_SSD1_N | 0.377 | – | – |
ISNS_P3V3_G3W_SSD1_P | 0.377 | – | – |
ISNS_P3V3S_WLAN_IOUT | OL | – | – |
ISNS_PPBUS_MAIN_SSD0_N | 0.415 | 12.600 | 410.000 |
ISNS_PPBUS_MAIN_SSD0_P | 0.415 | 12.600 | 410.000 |
ISNS_PPBUS_MAIN_SSD1_N | 0.415 | 12.600 | 410.000 |
ISNS_PPBUS_MAIN_SSD1_P | 0.415 | 12.600 | 410.000 |
ISNS_T139_N | OL | – | – |
ISNS_T139_P | OL | – | – |
ISNS_TBT_T_IOUT | OL | – | – |
ISNS_TBT_T_N | OL | – | – |
ISNS_TBT_T_P | OL | – | – |
ISNS_TBT_X_IOUT | 0.363 | – | – |
ISNS_TBT_X_N | OL | – | – |
ISNS_TBT_X_P | OL | – | – |
ISNS_VCCIO_IOUT | OL | – | – |
ISNS_WL1V8_IOUT | OL | – | – |
ISNS_WL1V8_N | OL | – | – |
ISNS_WL1V8_P | OL | – | – |
ISNS_WLAN_N | OL | – | – |
ISNS_WLAN_P | OL | – | – |
ISNS_WLAN_R_N | OL | – | – |
ISNS_WLAN_R_P | OL | – | – |
JTAG_ISP_TCK | 0.570 | – | – |
JTAG_ISP_TDI | 0.569 | – | – |
JTAG_ISP_TDO | 0.570 | – | – |
KBD_CAP_CATHODE | 0.529 | – | – |
KBD_CAPSLOCK_LED | 0.508 | – | – |
KBD_CONTROL_KEY | 0.492 | – | – |
KBD_CONTROL_L | 0.461 | – | – |
KBD_DRIVE_Y0 | 0.515 | – | – |
KBD_DRIVE_Y1 | 0.525 | – | – |
KBD_DRIVE_Y2 | 0.525 | – | – |
KBD_DRIVE_Y3 | 0.527 | – | – |
KBD_DRIVE_Y4 | 0.515 | – | – |
KBD_DRIVE_Y5 | 0.514 | – | – |
KBD_DRIVE_Y6 | 0.500 | – | – |
KBD_DRIVE_Y7 | 0.500 | – | – |
KBD_I2C_INT_L | 0.676 | – | – |
KBD_I2C_SCL | 0.715 | – | – |
KBD_I2C_SDA | 0.683 | – | – |
KBD_ID_DETECT1 | 0.514 | – | – |
KBD_ID_DETECT2 | 0.469 | – | – |
KBD_ID1 | 0.800 | – | – |
KBD_LEFT_OPTION_KEY | 0.492 | – | – |
KBD_LEFT_OPTION_L | 0.460 | – | – |
KBD_RIGHT_SHIFT_KEY | 0.495 | – | – |
KBD_RIGHT_SHIFT_L | 0.461 | – | – |
KBD_SENSE_X0 | 0.532 | – | – |
KBD_SENSE_X1 | 0.536 | – | – |
KBD_SENSE_X2 | 0.536 | – | – |
KBD_SENSE_X3 | 0.544 | – | – |
KBD_SENSE_X4 | 0.556 | – | – |
KBD_SENSE_X5 | 0.529 | – | – |
KBD_SENSE_X6 | 0.513 | – | – |
KBD_SENSE_X7 | 0.511 | – | – |
KBD_SENSE_X8 | 0.510 | – | – |
KBD_SENSE_X9 | 0.510 | – | – |
KBD_SENSE_X10 | 0.538 | – | – |
KBD_SENSE_X11 | 0.535 | – | – |
KBD_SENSE_X12 | 0.535 | – | – |
KBDBKLT_SW2 | 0.403 | 5.100 | – |
KBDLED_CATHODE1 | 0.674 | – | – |
KBDLED_CATHODE2 | 0.668 | – | – |
L83_FILT | 0.801 | – | – |
L83_FLYC | 0.372 | – | – |
L83_FLYN | 0.450 | – | – |
L83_FLYP | 0.404 | – | – |
L83_HSBIAS_FILT | 0.716 | – | – |
L83_HSBIAS_FILT_REF | 0.628 | – | – |
L83_SDOUT | 0.498 | – | – |
L83_VCP_FILT_GND | 0.000 | – | – |
L83_VCP_FILTN | 0.573 | – | – |
L83_VCP_FILTP | 0.387 | – | – |
LCD_MUX_SEL | OL | – | – |
LCD_PWR_SLEW | 0.617 | – | – |
LCD_PWR_SLEW_3V3 | 0.632 | – | – |
LCDBKLT_EN_L | OL | – | – |
LCDBKLT_FB | 0.732 | – | – |
LCDBKLT_FET_DRV | 0.508 | 1.100 | – |
LCDBKLT_FET_DRV_R | 0.520 | 1.100 | – |
LCDBKLT_SW | 0.439 | – | – |
LCDBKLT_TB_XWR | 1.181 | 59.000 | – |
LDO_CORE | 0.373 | – | – |
LDO_RTC | 0.373 | – | – |
LID_CTRL_DMIC | 0.700 | – | – |
LID_OPEN_SMC_IN | 0.491 | – | – |
MEM_B_TEN_R | 0.101 | – | – |
MEM_RESET_L | 0.399 | – | – |
MEMVTT_EN | 0.543 | – | – |
MEMVTT_EN_R | 0.543 | – | – |
MESA_BOOST_EN | 0.553 | – | – |
MESA_BOOST_EN_CONN | 1.238 | – | – |
MESA_INT | 0.493 | – | – |
MESA_INT_CONN | 1.177 | – | – |
MESA_PWR_EN | 0.483 | – | – |
MIPI_DFR_CLK_CONN_FILT_N | 0.550 | – | – |
MIPI_DFR_CLK_CONN_FILT_P | 0.552 | – | – |
MIPI_DFR_CLK_P | 0.550 | – | – |
MIPI_DFR_DATA_CONN_FILT_N | 0.547 | – | – |
MIPI_DFR_DATA_CONN_FILT_P | 0.547 | – | – |
MIPI_DFR_DATA_N | 0.547 | – | – |
MIPI_DFR_DATA_P | 0.547 | – | – |
MIPI_FTCAM_CLK_CONN_N | 0.523 | – | – |
MIPI_FTCAM_CLK_CONN_P | 0.524 | – | – |
MIPI_FTCAM_CLK_ISOL_N | 0.523 | – | – |
MIPI_FTCAM_CLK_ISOL_P | 0.524 | – | – |
MIPI_FTCAM_DATA_CONN_N<0> | 0.524 | – | – |
MIPI_FTCAM_DATA_CONN_P<0> | 0.523 | – | – |
MIPI_FTCAM_DATA_ISOL_N<0> | 0.524 | – | – |
MIPI_FTCAM_DATA_ISOL_P<0> | 0.523 | – | – |
MLB_RAMCFG1 | 0.780 | – | – |
MLBSNS_I2CLS_EN | OL | – | – |
NTC_A_CPUCORE | 0.628 | – | – |
NTC_A_CPUCORE_R | OL | – | – |
NTC_B_CPUGT | 0.587 | – | – |
NTC_B_CPUGT_R | OL | – | – |
OUT123_EN | 0.302 | – | – |
P0V8SLPDDR_FB | 0.051 | – | 50.100R |
P0V8SLPDDR_FB_R | 0.054 | – | 53.100R |
P0V8SLPDDR_SW0 | 0.053 | 0.800 | 52.800R |
P0V8SLPDDR_SW1 | 0.053 | 0.800 | 52.800R |
P0V9_LX0_SSD0 | 0.401 | 0.900 | 398.000R |
P0V9_LX0_SSD1 | 0.468 | 0.900 | 462.000R |
P0V9_LX1_SSD0 | 0.401 | 0.900 | 398.000 |
P0V9_LX1_SSD1 | 0.468 | 0.900 | 462.000R |
P0V9_SSD0_FB_DIS | 0.392 | – | – |
P0V9_SSD1_FB_DIS | 0.483 | – | – |
P0V9_TBT_T_SVR_AGND | 0.000 | – | – |
P0V9_TBT_X_SVR_AGND | 0.000 | – | – |
P0V9SLPDDR_SW0 | 0.084 | 0.900 | 85.100R |
P0V9SLPDDR_SW1 | 0.084 | 0.900 | 85.100R |
P1V1_SLPDDR_SOCFET_EN | 0.570 | – | – |
P1V1_SLPDDR_SOCFET_EN_R | OL | – | – |
P1V1SLPDDR_RAMP | 0.719 | – | – |
P1V1SLPS2R_SW0 | 0.287 | 1.100 | 0.011R |
P1V1SLPS2R_SW1 | 0.287 | 1.100 | 0.011R |
P1V2_BOOT_RC | 0.630 | – | – |
P1V2_DRVH | 0.713 | – | – |
P1V2_DRVH_R | 0.714 | – | – |
P1V2_DRVL | 0.458 | – | – |
P1V2_DRVL_R | 0.458 | – | – |
P1V2_LL_SNUB | OL | – | – |
P1V2_PHASE | 0.223 | 1.200 | 221.000 |
P1V2_SNS | 0.235 | – | – |
P1V2_SNS_R | 0.225 | – | – |
P1V2_SW | 0.225 | – | – |
P1V2_VBST | 0.627 | – | – |
P1V2_WLANBT_VLX | 0.300 | 1.200 | 0.200R |
P1V2REG_AGND | 0.000 | – | – |
P1V2REG_MODE | 0.545 | – | – |
P1V2REG_TRIP | 0.750 | – | – |
P1V2REG_VREF | 0.651 | – | – |
P1V2REG_VREF_R | OL | – | – |
P1V5_WLANBT_VLX | 0.320 | 1.500 | 0.017R |
P1V8_G3S_EN_R | OL | – | – |
P1V8_LX0_SSD0 | 0.379 | 1.800 | 0.090R |
P1V8_LX0_SSD1 | 0.425 | 1.800 | 0.128R |
P1V8_SLPS2RSW_DFR_R | 0.610 | – | – |
P1V8_SSD0_FB_DIS | 0.376 | – | – |
P1V8_SSD1_FB_DIS | 0.430 | – | – |
P1V8G3S_EN | – | 1.80 | – |
P1V8GPU_EN | 0.603 | – | – |
P1V8GPU_FB | 1.421 | – | – |
P1V8GPU_FB_R | 0.197 | – | – |
P1V8GPU_PGOOD | 0.595 | – | – |
P1V8GPU_RA_R | 0.197 | – | – |
P1V8GPU_SSTR | 0.544 | – | – |
P1V8S5_VALID | 0.542 | – | – |
P1V8SLPS2R_SW0 | 0.409 | 1.800 | 0.003R |
P2V5_SSD0_AGND | 0.000 | – | – |
P2V5_SSD1_AGND | 0.000 | – | – |
P2V5_SW1_TPS62180_SSD0 | 0.408 | 2.500 | 0.150R |
P2V5_SW1_TPS62180_SSD1 | 0.429 | 2.500 | 0.175R |
P2V5_SW2_TPS62180_SSD0 | 0.408 | 2.500 | 0.150R |
P2V5_SW2_TPS62180_SSD1 | 0.429 | 2.500 | 0.175R |
P2V5_VPP_PGOOD | 0.497 | – | – |
P2V5S3_FSW | 0.420 | – | – |
P2V5S3_REG | 0.420 | 2.500 | – |
P3V3_G3H_RTC_DEBUG_LED_R | OL | – | – |
P3V3_S0GPU_PGOOD | 0.610 | – | – |
P3V3G3H_COMP2 | 0.747 | – | – |
P3V3G3H_CSN2 | 0.377 | 3.300 | – |
P3V3G3H_CSP2 | 1.268 | – | – |
P3V3G3H_CSP2_R | 0.378 | 3.300 | – |
P3V3G3H_DRVH | 0.934 | – | – |
P3V3G3H_DRVL | 0.558 | – | – |
P3V3G3H_EN | 0.592 | – | – |
P3V3G3H_RF | 0.590 | – | – |
P3V3G3H_SNUBR | OL | – | – |
P3V3G3H_SW | 0.376 | – | – |
P3V3G3H_TG | 0.933 | – | – |
P3V3G3H_VBST | 0.628 | – | – |
P3V3G3H_VBST_R | 0.628 | – | – |
P3V3G3H_VFB2 | 0.593 | – | – |
P3V3G3H_VFB2_R | 0.377 | – | – |
P3V3G3H_VFB2_RR | 1.304 | – | – |
P3V3G3H_VSW | 0.378 | 3.300 | – |
P3V3G3HRTC_FB | 1.423 | – | – |
P3V3G3HRTC_FB_R | 0.430 | – | – |
P3V3G3HRTC_PGOOD | 0.697 | – | – |
P3V3G3HRTC_PHASE1 | 0.421 | 3.300 | – |
P3V3G3HRTC_PHASE2 | 0.421 | 3.300 | – |
P3V3G3HRTC_RA_R | 0.430 | – | – |
P3V3G3HRTC_SS | 0.542 | – | – |
P3V3G3S_EN | 0.539 | – | – |
P3V3G3ST_SS | 0.635 | – | – |
P3V3G3SX_SS | 0.639 | – | – |
P3V3GPU_EN | 0.504 | – | – |
P3V3GPU_RAMP | 0.716 | – | – |
P3V3MAIN_PGOOD | 0.585 | – | – |
P3V3S5_COMP2_R | OL | – | – |
P3V3TBTT_CMP | 0.499 | – | – |
P3V3TBTT_RAMP | 0.620 | – | – |
P3V3TBTX_CMP | 0.500 | – | – |
P3V3TBTX_RAMP | 0.616 | – | – |
P5V_3V3G3H_EN | 0.592 | – | – |
P5VG3S_COMP1 | 0.748 | – | – |
P5VG3S_CSN1 | 0.401 | – | – |
P5VG3S_CSP1 | 0.990 | – | – |
P5VG3S_CSP1_R | 0.402 | – | – |
P5VG3S_DRVH | 0.960 | – | – |
P5VG3S_EN | 0.591 | – | – |
P5VG3S_EN_R | 0.591 | 3.30 | – |
P5VG3S_PGOOD | 0.586 | 1.80 | – |
P5VG3S_SNUBR | OL | – | – |
P5VG3S_SW | 0.401 | – | – |
P5VG3S_TG | 0.961 | – | – |
P5VG3S_VBST | 0.630 | – | – |
P5VG3S_VBST_R | 0.630 | – | – |
P5VG3S_VFB1 | 0.582 | – | – |
P5VG3S_VFB1_R | 0.401 | – | – |
P5VG3S_VSW | 0.405 | 5.00 | – |
P5VP3V3_SKIPSEL | 0.470 | – | – |
P5VP3V3_VREF2 | 0.487 | – | – |
P5VP3V3_VREG3 | 0.517 | – | – |
P5VS4_COMP1_R | OL | – | – |
P5VUSBC_X_AGND | 0.000 | – | – |
P5VUSBC_X_BOOT_RC | 0.605 | – | – |
P5VUSBC_X_DRVH | 0.683 | – | – |
P5VUSBC_X_DRVH_R | 0.683 | – | – |
P5VUSBC_X_FSEL | 0.565 | – | – |
P5VUSBC_X_LL | 0.485 | 5.000 | – |
P5VUSBC_X_NEG | 0.188 | – | – |
P5VUSBC_X_OCSET | 0.556 | – | – |
P5VUSBC_X_PGOOD | 0.563 | – | – |
P5VUSBC_X_POS | 0.188 | – | – |
P5VUSBC_X_R | 0.485 | 5.000 | 186.000 |
P5VUSBC_X_RTN_DIV | 0.559 | – | – |
P5VUSBC_X_RTN_DIV_XW | 0.003 | – | 1.600R |
P5VUSBC_X_SENSE_DIV | 0.557 | – | – |
P5VUSBC_X_SET_R | OL | – | – |
P5VUSBC_X_SET0 | 0.530 | – | – |
P5VUSBC_X_SET1 | 0.562 | – | – |
P5VUSBC_X_SREF | 0.560 | – | – |
P5VUSBC_X_VBST | 0.607 | – | – |
P5VUSBCT_AGND | 0.000 | – | – |
P5VUSBCT_BOOT_RC | 0.608 | – | – |
P5VUSBCT_DRVH | 0.665 | – | – |
P5VUSBCT_DRVH_R | 0.665 | – | – |
P5VUSBCT_FSEL | 0.566 | – | – |
P5VUSBCT_LL | 0.195 | 5.000 | 0.001R |
P5VUSBCT_N | 0.193 | – | – |
P5VUSBCT_OCSET | 0.558 | – | – |
P5VUSBCT_P | 0.193 | – | – |
P5VUSBCT_R | 0.195 | 5.000 | 0.001R |
P5VUSBCT_RTN_DIV | 0.562 | – | – |
P5VUSBCT_RTN_DIV_R | 0.000 | – | – |
P5VUSBCT_SENSE_DIV | 0.560 | – | – |
P5VUSBCT_SENSE_DIV_R | 0.195 | – | – |
P5VUSBCT_SET_R | OL | – | – |
P5VUSBCT_SET0 | 0.565 | – | – |
P5VUSBCT_SET1 | 0.563 | – | – |
P5VUSBCT_SREF | 0.563 | – | – |
P5VUSBCT_VBST | 0.607 | – | – |
P5VUSBCT_VO | 0.558 | – | – |
PANEL_P3V3_EN | 0.489 | – | – |
PANEL_P3V3_EN_D | 0.701 | – | – |
PANEL_P5V_EN | 0.569 | – | – |
PANEL_P5V_EN_D | 1.039 | – | – |
PBUS_DIVIDER | 0.706 | – | – |
PBUS_DIVIDER_OUT | 0.655 | – | – |
PBUS_DIVIDER_REF | 0.660 | – | – |
PBUS_S0_VSENSE | OL | 12.650 | – |
PBUS_S0_VSENSE_IN | 0.415 | 12.600 | – |
PBUSVSENS_EN_L | 0.488 | 0.000 | – |
PBUSVSENS_EN_L_DIV | OL | 6.300 | – |
PCC_EVENT | 0.494 | – | – |
PCC_GFXGPU_SUM | 0.468 | – | – |
PCH_BATLOW_L | 0.800 | – | – |
PCH_BT_ROM_BOOT_L | 0.539 | – | – |
PCH_CLK24M_XTALIN | 0.838 | – | – |
PCH_CLK24M_XTALOUT_R | 0.835 | – | – |
PCH_CLK32K_RTCX1 | 0.862 | – | – |
PCH_DRAM_RESET_L | 0.399 | – | – |
PCH_GPPJ_RCOMP_1P8 | 0.204 | – | – |
PCH_PCIE_CLK100M_WLAN_N | 0.312 | – | – |
PCH_PCIE_CLK100M_WLAN_P | 0.311 | – | – |
PCH_PCIE_RCOMPN | 0.296 | – | – |
PCH_PCIE_RCOMPP | 0.296 | – | – |
PCH_PMTHRMTRIP_L | 0.555 | – | – |
PCH_PMTHRMTRIP_L_R | 0.553 | – | – |
PCH_RTC_RESET_L | 0.771 | 3.00 | – |
PCH_STRP_ESPI | 0.808 | – | – |
PCH_STRP_GPP_H15 | 0.830 | – | – |
PCH_UART_BT_CTS_L | 0.499 | – | – |
PCH_UART_BT_RTS_L | 0.455 | – | – |
PCH_UART_DEBUG_D2R | 0.709 | – | – |
PCH_UART_DEBUG_R2D | 0.707 | – | – |
PCH_WLANBT_PERST_L | 0.826 | – | – |
PCIE_SSD0_D2R_C_N<3> | 0.360 | – | – |
PCIE_SSD0_D2R_C_P<3> | 0.325 | – | – |
PCIE_SSD0_D2R_N<3> | 0.435 | – | – |
PCIE_SSD0_D2R_P<3> | 0.433 | – | – |
PCIE_SSD0_R2D_C_N<3> | 0.373 | – | – |
PCIE_SSD0_R2D_C_P<3> | 0.373 | – | – |
PCIE_SSD0_R2D_N<3> | 0.442 | – | – |
PCIE_SSD0_R2D_P<3> | 0.440 | – | – |
PDM_DMIC_DATA0 | 0.403 | – | – |
PDM_DMIC_DATA0_RR | 0.494 | – | – |
PDM_DMIC_DATA1 | 0.477 | – | – |
PDM_DMIC_DATA1_RR | 0.487 | – | – |
PLT_RST_L | 0.396 | – | – |
PLT3V3_RST_L | 0.634 | – | – |
PM_ALL_GPU_PGOOD | 0.457 | – | – |
PM_MEMVTT_EN | 0.376 | – | – |
PM_PCH_PWROK | 0.497 | – | – |
PM_PCH_SYS_PWROK | 0.547 | – | – |
PM_PWRBTN_L | 0.762 | – | – |
PM_RSMRST_L | 0.528 | – | – |
PM_SLP_S0_L | 0.491 | – | – |
PM_SLP_S0_R_L | OL | – | – |
PM_SLP_S3_L | 0.564 | – | – |
PM_SLP_S4_L | 0.815 | – | – |
PM_SLP_S5_L | 0.815 | – | – |
PM_SLP_TIEOFF | 0.719 | – | – |
PM_SYSRST_L | 0.810 | – | – |
PM_SYSRST_R_L | 0.553 | – | – |
PM_THRMTRIP_L | 0.258 | – | – |
PMU_3V3_T_HI_ISENSE | 0.586 | – | – |
PMU_3V3_X_HI_ISENSE | 0.589 | – | – |
PMU_ACTIVE_READY | 0.469 | – | – |
PMU_ACTIVE_READY_R | OL | – | – |
PMU_CLK32K_PCH | 0.810 | – | – |
PMU_CLK32K_SOC | 0.496 | – | – |
PMU_CLK32K_SOC_R | 0.530 | – | – |
PMU_CLK32K_WLANBT_R | 0.485 | – | – |
PMU_COLD_RESET_L | 0.490 | – | – |
PMU_CPU_ISENSE | 0.591 | – | – |
PMU_CPU_VSENSE | 0.584 | – | – |
PMU_CPUDDR_ISENSE | 0.590 | – | – |
PMU_DDR1V2_ISENSE | 0.586 | – | – |
PMU_DROOP_L | 0.495 | – | – |
PMU_FORCE_DFU | 0.769 | – | – |
PMU_GPU_GFX_ISENSE | 0.590 | – | – |
PMU_GPU_GFX_VSENSE | 0.584 | – | – |
PMU_GPU_SOC_ISENSE | 0.589 | – | – |
PMU_GPU_SOC_VSENSE | 0.589 | – | – |
PMU_IREF | 0.761 | – | – |
PMU_LDO3_OUT_R | 0.601 | – | – |
PMU_ONOFF_L | 0.590 | – | – |
PMU_ONOFF_R_L | 0.585 | – | – |
PMU_ONOFF_R_L_CONN | 0.586 | – | – |
PMU_OTHER5V_HI_ISENSE | 0.588 | – | – |
PMU_P1V8_WLAN_ISENSE | 0.590 | – | – |
PMU_P3V3_G3W_SSD0_ISENSE | 0.557 | – | – |
PMU_P3V3_G3W_SSD1_ISENSE | 0.588 | – | – |
PMU_PBUS_MAIN_SSD0_ISENSE | 0.586 | – | – |
PMU_PBUS_MAIN_SSD1_ISENSE | 0.588 | – | – |
PMU_PVDDMAIN_EN | 0.773 | – | – |
PMU_RSLOC_RST_L | 0.522 | – | – |
PMU_SYS_ALIVE | 0.435 | – | – |
PMU_VDD_HI | 0.660 | – | – |
PMU_VDD_MAX | 0.560 | – | – |
PMU_VPUMP | 0.591 | – | – |
PMU_VREF | 0.002 | – | – |
PMU_XTAL1 | 0.796 | – | – |
PMU_XTAL1_R | 0.796 | – | – |
PMU_XTAL2 | 0.796 | – | – |
PP_VDD_SE_VDDA | 0.336 | – | – |
PP_VDD_SE_VDDC | 0.342 | – | – |
PP_VDD_SE_VDDNV | 0.367 | – | – |
PP_VDD_SE_VDDPLL | 0.365 | – | – |
PP_VDD_SE_VHV | 0.323 | – | – |
PP_VDD_SE_VREF | 0.696 | – | – |
PP0V6_S0_DDRVTT | 0.132 | – | – |
PP0V8_SLPS2R | 0.253 | – | – |
PP0V9_SLPDDR | 0.084 | 0.900 | 85.100R |
PP0V9_SLPDDR_SOC_PCIEREFBUF | 0.085 | – | 83.400R |
PP0V9_SSD0 | 0.401 | 0.900 | 398.000 |
PP0V9_SSD1 | 0.468 | 0.900 | 462.000 |
PP0V9_TBT_T_LC | 0.347 | – | – |
PP0V9_TBT_T_LVR | 0.460 | – | – |
PP0V9_TBT_T_PCIE | 0.316 | – | – |
PP0V9_TBT_T_SVR | 0.288 | 0.900 | 286.000 |
PP0V9_TBT_X_LVR | 0.478 | – | – |
PP0V9_TBT_X_PCIE | 0.324 | – | – |
PP0V9_TBT_X_SVR | 0.320 | 0.900 | 312.000R |
PP0V75_S0_GPU | 0.050 | 0.750 | 49.300R |
PP0V82_SLPDDR | 0.053 | 0.800 | 52.800R |
PP0V85_MEMCI_S0_GPU | 0.089 | 0.850 | 88.400R |
PP0V95_S0_CPUVCCIO_REG_R | 0.076 | – | 83.200R |
PP1V_PRIM_PCH_VCCAMPHYPLL_F | 0.096 | 1.050 | 94.000R |
PP1V1_SLPDDR | 0.388 | – | – |
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F | 0.388 | – | – |
PP1V1_SLPDDR_SOC_XTAL_F | 0.388 | – | – |
PP1V1_SLPS2R | 0.287 | 1.100 | 0.011R |
PP1V2_AWAKE | 0.525 | – | – |
PP1V2_AWAKE_SOC_PCIEPLL_F | 0.525 | – | – |
PP1V2_AWAKE_SOC_PCIEREFBUF_F | 0.000 | – | – |
PP1V2_AWAKE_SOC_PLLCPU_F | 0.522 | – | – |
PP1V2_AWAKE_SOC_PLLSOC_F | 0.523 | – | – |
PP1V2_S0SW | 0.303 | – | – |
PP1V2_S3 | 0.223 | 1.200 | 221.000 |
PP1V2_S3_CPUDDR | 0.220 | 1.200 | 226.000 |
PP1V2_S3_REG_R | 0.223 | 1.200 | 221.000 |
PP1V2_WLANBT | 0.299 | – | – |
PP1V2_WLANBT_C | 0.300 | 1.200 | 0.200R |
PP1V05_PRIM | 0.096 | – | 94.000R |
PP1V05_PRIM_PCH_VCCAPLL_F | 0.096 | – | – |
PP1V05_PRIM_PCH_VCCAXTAL_F | 0.096 | – | 94.800R |
PP1V05_S0SW | 0.208 | – | – |
PP1V05_S3 | 0.219 | – | – |
PP1V5_UPC_TA_LDO_CORE | 0.501 | – | – |
PP1V5_UPC_TB_LDO_CORE | 0.501 | 1.500 | – |
PP1V5_UPC_XA_LDO_CORE | 0.501 | – | – |
PP1V5_UPC_XB_LDO_CORE | 0.504 | – | – |
PP1V5_WLANBT | 0.327 | – | – |
PP1V5_WLANBT_C | 0.320 | 1.500 | 0.017R |
PP1V8_AUDIO | 0.300 | – | – |
PP1V8_AWAKE | 0.390 | 1.800 | – |
PP1V8_DMIC | 0.305 | – | – |
PP1V8_G3S | 0.301 | 1.80 | – |
PP1V8_G3S_TPAD_CONN | 0.544 | – | – |
PP1V8_G3S_WLANBT | 0.301 | – | – |
PP1V8_L83_VA | 0.300 | – | – |
PP1V8_L83_VCP | 0.300 | – | – |
PP1V8_L83_VL | 0.300 | – | – |
PP1V8_MESA | 0.521 | – | – |
PP1V8_MESA_FILT_CONN | 0.521 | – | – |
PP1V8_PCH_VCCPHYLDO | 0.658 | – | – |
PP1V8_S0_GPU | 0.190 | – | – |
PP1V8_S0_GPU_CONN | OL | – | – |
PP1V8_S0_GPU_REG | 0.200 | 1.800 | 0.001R |
PP1V8_S0_PCH_VCCHDA_F | 0.363 | – | 0.019R |
PP1V8_S5 | 0.363 | – | 0.019R |
PP1V8_S5_GPIOX_R | 0.364 | – | – |
PP1V8_S5_TBTTHMSNS_T_R | 0.410 | – | – |
PP1V8_S5_TBTTHMSNS_X_R | 0.410 | – | – |
PP1V8_SLPS2R | 0.409 | 1.800 | 0.003R |
PP1V8_SLPS2R_PMUVDDGPIO | 0.739 | – | – |
PP1V8_SLPS2R_SOC_LPADC_RC | 0.453 | – | – |
PP1V8_SLPS2R_SOC_LPOSC_RC | 0.458 | – | – |
PP1V8_SLPS2RSW_DFR | 0.535 | – | – |
PP1V8_SSD0 | 0.379 | 1.800 | 0.090R |
PP1V8_SSD0_S4E1_AVDD18_PLL | 0.375 | – | – |
PP1V8_SSD0_S4E1_PCI_AVDD_H | 0.375 | – | – |
PP1V8_SSD1 | 0.425 | 1.800 | 0.128R |
PP1V24_S5_PCH_VCCDPHY | 0.428 | – | – |
PP1V25_SLPS2R_SMC_AVREF | 0.616 | – | – |
PP1V35_MEMIO_S0_GPU | 0.048 | 1.350 | 46.600R |
PP2V5_NAND_SSD0 | 0.408 | 2.500 | 0.150R |
PP2V5_NAND_SSD1 | 0.429 | 2.500 | 0.175R |
PP2V5_S3 | 0.420 | 2.500 | – |
PP3V0_G3H_RTC | 0.461 | – | – |
PP3V0_MESA | 0.551 | – | – |
PP3V0_MESA_FILT_CONN | 0.551 | – | – |
PP3V3_AWAKE | 0.645 | – | – |
PP3V3_G3H_DFR | 0.420 | – | – |
PP3V3_G3H_MESA_SW | 0.377 | – | – |
PP3V3_G3H_PMU_VINRTC_R | 0.421 | – | – |
PP3V3_G3H_RSLOC | 0.383 | – | – |
PP3V3_G3H_RTC_REG_R | 0.421 | 3.300 | – |
PP3V3_G3H_RTC_X | 0.421 | – | – |
PP3V3_G3H_SOCPMU | 0.378 | 3.300 | – |
PP3V3_G3H_SSD0_SNS | 0.421 | 3.300 | – |
PP3V3_G3H_SSD1_SNS | 0.377 | 3.300 | – |
PP3V3_G3H_T | 0.378 | 3.300 | – |
PP3V3_G3HSW_DFR | 0.568 | – | – |
PP3V3_G3S_T | 0.428 | – | – |
PP3V3_G3S_WLAN | 0.349 | – | – |
PP3V3_G3S_X | 0.349 | – | – |
PP3V3_G3SSW_SNS | 0.494 | 3.400 | – |
PP3V3_L83_VP | 0.377 | – | – |
PP3V3_S0_GPU | 0.416 | – | – |
PP3V3_S0SW_LCD | 0.484 | 3.300 | – |
PP3V3_S0SW_LCD_R | 0.485 | – | – |
PP3V3_S0SW_TBT_T | 0.537 | – | – |
PP3V3_S0SW_TBT_T_SNS | 0.500 | 3.300 | – |
PP3V3_S0SW_TBT_X | 0.532 | – | – |
PP3V3_S0SW_TBT_X_SNS | 0.532 | – | – |
PP3V3_S5 | 0.335 | – | – |
PP3V3_S5_GPIOX_R | 0.335 | – | – |
PP3V3_TBT_T_ANA | 0.537 | – | – |
PP3V3_TBT_T_ANA_PCIE | 0.490 | – | – |
PP3V3_TBT_T_F | 0.500 | 3.300 | – |
PP3V3_TBT_T_LC | 0.554 | – | – |
PP3V3_TBT_T_SX | 0.481 | – | – |
PP3V3_TBT_X_ANA | 0.537 | – | – |
PP3V3_TBT_X_ANA_PCIE | 0.503 | – | – |
PP3V3_TBT_X_ANA_USB2 | 0.508 | – | – |
PP3V3_TBT_X_F | 0.517 | – | – |
PP3V3_TBT_X_LC | 0.559 | – | – |
PP3V3_TBT_X_SX | 0.486 | – | – |
PP3V3_UPC_TA_LDO | 0.475 | – | – |
PP3V3_UPC_TB_LDO | 0.490 | 3.300 | – |
PP3V3_UPC_XA_LDO | 0.493 | – | – |
PP3V3_UPC_XB_LDO | 0.483 | – | – |
PP5V_COREVR_VCC | 0.405 | – | – |
PP5V_EADC1_AVDD | OL | – | – |
PP5V_EADC2_AVDD | OL | – | – |
PP5V_EDRAM_V5IN | 0.403 | – | – |
PP5V_G3S | 0.405 | 5.000 | – |
PP5V_G3S_BKLT_A | 0.413 | 5.100 | – |
PP5V_G3S_BKLT_D | 0.413 | 5.100 | – |
PP5V_G3S_DFR_FILT | 0.405 | – | – |
PP5V_G3S_GPU_COREREG_VDD | 0.404 | – | – |
PP5V_G3S_GPU_VDD075REG_R | 0.405 | – | – |
PP5V_G3S_ISNS_D | OL | – | – |
PP5V_G3S_KBDLED | 0.403 | 5.000 | – |
PP5V_G3S_TPAD_CONN | 0.403 | – | – |
PP5V_G3S_VCCIOVCC | 0.403 | – | – |
PP5V_S0_ALSCAM_F | 0.404 | 5.000 | – |
PP5V_S0SW_LCD | 0.570 | 5.000 | – |
PP5V_S4_T_USBC | 0.193 | 5.000 | – |
PP5V_S4_X_USBC | 0.188 | 5.000 | 186.000 |
PP5V_S5_LDO | 0.485 | – | – |
PP5V_USBC_X_VCC | 0.405 | – | – |
PP5V_USBCT_VCC | 0.406 | – | – |
PP16V0_MESA | 0.655 | – | – |
PP16V0_MESA_FILT_CONN | 0.656 | – | – |
PP17V0_MOJAVE_LDOIN | 0.596 | – | – |
PPBUS_G3H | 0.415 | 12.600 | 410.000 |
PPBUS_G3H_SPKRAMPL | 0.414 | 12.600 | – |
PPBUS_G3H_SSD0_SNS | 0.415 | 12.600 | 410.000 |
PPBUS_G3H_SSD1_SNS | 0.415 | 12.600 | 410.000 |
PPBUS_HS_3V3G3H_T | 0.415 | 12.600 | 410.000 |
PPBUS_HS_3V3G3HRTC_X | 0.415 | – | 410.000 |
PPBUS_HS_CPU | 0.415 | 12.600 | 410.000 |
PPBUS_HS_GPU | 0.415 | 12.600 | 409.000R |
PPBUS_HS_OTH5V | 0.415 | 12.600 | 0.200R |
PPDCIN_G3H | 0.550 | 20.000 | – |
PPDCIN_G3H_CHGR | 0.552 | 20.000 | – |
PPDCIN_TA_G3H_F | 0.550 | 20.000 | – |
PPDCIN_TB_G3H_F | 0.550 | 20.000 | – |
PPDCIN_XA_G3H_F | 0.550 | 20.000 | – |
PPDCIN_XB_G3H_F | 0.550 | 20.000 | – |
PPGFX_S0_GPU | 0.016 | 0.900 | 14.800R |
PPGFX_S0_GPU_R1 | 0.016 | 0.900 | 14.800R |
PPGFX_S0_GPU_R2 | 0.016 | 0.900 | 14.800R |
PPGFX_S0_GPU_R3 | 0.016 | 0.900 | 14.800R |
PPGFX_S0_GPU_R4 | 0.016 | 0.900 | 14.800R |
PPGFX_S0_GPU_SW1 | 0.016 | 0.900 | – |
PPGFX_S0_GPU_SW2 | 0.016 | 0.900 | – |
PPGFX_S0_GPU_SW3 | 0.016 | 0.900 | – |
PPGFX_S0_GPU_SW4 | 0.016 | 0.900 | – |
PPSOC_S0_GPU | 0.007 | 0.900 | 7.400R |
PPSOC_S0_GPU_R | 0.007 | 0.900 | 4.000R |
PPSOC_S0_GPU_SW | 0.007 | – | 4.000R |
PPVBAT_G3H_CHGR_R | 0.415 | 12.600 | 410.000 |
PPVBAT_G3H_CHGR_REG | 0.415 | 12.600 | 410.000 |
PPVBAT_G3H_CONN | 1.569 | – | – |
PPVBUS_USBC_TA | 0.141 | 20.000 | – |
PPVBUS_USBC_TB | 0.141 | 20.000 | – |
PPVBUS_USBC_XA | 0.144 | 20.000 | – |
PPVBUS_USBC_XB | 0.144 | 20.000 | – |
PPVCC_CPU_PH1 | 0.002 | 1.500 | 2.400R |
PPVCC_CPU_PH2 | 0.002 | 1.500 | 2.400R |
PPVCC_CPU_PH3 | 0.002 | 1.500 | 2.400R |
PPVCC_S0_CPU | 0.002 | 1.500 | 2.400R |
PPVCCGT_CPU_PH1 | 0.010 | 1.500 | 9.500R |
PPVCCGT_CPU_PH2 | 0.010 | 1.500 | 9.500R |
PPVCCGT_S0_CPU | 0.010 | 1.500 | 9.500R |
PPVCCIO_S0_CPU | 0.076 | 0.950 | 75.000R |
PPVCCPRIM_FETIN | 0.107 | – | – |
PPVCCPRIMCORE_PRIM_REG | 0.109 | 1.050 | 107.400R |
PPVCCSA_CPU_R | 0.033 | 1.150 | 21.400R |
PPVCCSA_S0_CPU | 0.033 | 1.150 | 21.400R |
PPVCCSPI_PRIM_PCH | 0.335 | – | – |
PPVDD075_GPU_R | 0.050 | 0.750 | 23.000R |
PPVDDCIMEM_GPU_R | 0.089 | 0.850 | 31.000R |
PPVDDCPU_AWAKE | 0.032 | 1.060 | 31.900R |
PPVDDCPUSRAM_AWAKE | 0.355 | 1.060 | 353.000 |
PPVDDIOMEM_GPU_R1 | 0.048 | 1.350 | 38.000R |
PPVDDIOMEM_GPU_R2 | 0.048 | 1.350 | 38.000R |
PPVIN_G3H_P3V3G3HRTC_R | 0.415 | 13.100 | – |
PPVIN_GPU_COREREG_VIN | 0.414 | – | – |
PPVIN_RFLDO_WLANBT | 0.498 | – | – |
PPVIN_RFLDO_WLANBT_C | 0.328 | 1.800 | 0.100R |
PPVIN_S0_CPUVR_VIN | 0.422 | – | – |
PPVIN_S0SW_LCDBKLT | 0.833 | 12.600 | – |
PPVIN_S0SW_LCDBKLT_FET | 0.415 | 12.600 | 410.000 |
PPVIN_S0SW_LCDBKLT_R | 0.415 | 12.600 | – |
PPVIN_S3_DDR2V5_RC | 0.420 | – | – |
PPVIN_SW_LCDBKLT_SW | 0.833 | 12.600 | 0.512R |
PPVOUT_S0_KBDLED | 0.601 | – | – |
PPVOUT_S0_KBDLED_R | 0.608 | 40.000 | – |
PPVOUT_S0_LCDBKLT | 1.148 | 55.000 | – |
PPVOUT_S0_LCDBKLT_F | 1.181 | 59.000 | 0.177R |
PPVTT_VTTREF | 0.501 | – | – |
PROG1_CPUCOREVR | 0.618 | – | – |
PROG2_CPUCOREVR | 0.619 | – | – |
PROG3_CPUCOREVR | 0.600 | – | – |
PROG4_CPUCOREVR | 0.627 | – | – |
PROG5_CPUCOREVR | 0.626 | – | – |
PVCCEDRAM_REFIN | 0.705 | – | – |
PVCCIO_BOOT_RC | 0.567 | – | – |
PVCCIO_DRVH | 0.549 | – | – |
PVCCIO_DRVH_R | 0.548 | – | – |
PVCCIO_DRVL | 0.000 | – | 0.264R |
PVCCIO_DRVL_R | 0.458 | – | – |
PVCCIO_EN | 0.553 | – | – |
PVCCIO_LL | 0.058 | – | 58.100R |
PVCCIO_LL_SNUB | OL | – | – |
PVCCIO_PGOOD | 0.549 | – | – |
PVCCIO_PHASE | 0.076 | – | – |
PVCCIO_VBST | 0.060 | – | 0.300R |
PVCCIOS0_AGND | 0.000 | – | – |
PVCCIOS0_CS_N | 0.076 | – | 83.200R |
PVCCIOS0_CS_P | 0.076 | – | 83.200R |
PVCCIOS0_EN | 0.772 | – | – |
PVCCIOS0_EN_FILT | 0.763 | – | – |
PVCCIOS0_EN_FILT_BUF | 0.553 | – | – |
PVCCIOS0_EN_R | 0.810 | – | – |
PVCCIOS0_FB | 0.537 | – | – |
PVCCIOS0_FSEL | 0.554 | – | – |
PVCCIOS0_RTN | 0.541 | – | – |
PVCCIOS0_SREF | 0.552 | – | – |
PVCCIOS0_VO | 0.547 | – | – |
PVCCOIOS0_OCSET | 0.547 | – | – |
PVCCPRIMCORE_FB | 0.108 | – | – |
PVCCPRIMCORE_FB_R | 0.108 | – | – |
PVCCPRIMCORE_SW0 | 0.109 | 1.050 | – |
PVCCPRIMCORE_SW1 | 0.109 | 1.050 | – |
PVDD_GPU_CORE_COMP_C | 2.346 | – | – |
PVDD18GPU_SW1 | 0.200 | 1.800 | 0.001R |
PVDD18GPU_SW2 | 0.200 | 1.800 | 0.001R |
PVDD075GPU_BOOT | 0.564 | – | – |
PVDD075GPU_BOOT_RC | 0.559 | – | – |
PVDD075GPU_EN | 0.625 | – | – |
PVDD075GPU_EN_FILT | 0.765 | – | – |
PVDD075GPU_EN_FILT_BUF | 0.551 | – | – |
PVDD075GPU_EN_RC | 0.811 | – | – |
PVDD075GPU_ISNS_N | 0.050 | 0.750 | 49.300R |
PVDD075GPU_ISNS_P | 0.050 | 0.750 | 49.300R |
PVDD075GPU_OCSET | 0.545 | – | – |
PVDD075GPU_PGOOD | 0.530 | – | – |
PVDD075GPU_PHASE | 0.050 | 0.750 | 23.000R |
PVDD075GPU_UGATE | 0.542 | – | – |
PVDD075GPU_VO | 0.545 | – | – |
PVDDCIMEMGPU_BOOT_R | 0.538 | – | – |
PVDDCIMEMGPU_COMP | 0.605 | – | – |
PVDDCIMEMGPU_FB | 0.308 | – | – |
PVDDCIMEMGPU_FB_R | OL | – | – |
PVDDCIMEMGPU_IMON | 0.633 | – | – |
PVDDCIMEMGPU_ISEN1 | 0.629 | – | – |
PVDDCIMEMGPU_ISUMN | 0.092 | – | 90.600R |
PVDDCIMEMGPU_ISUMN_R | 0.538 | – | – |
PVDDCIMEMGPU_ISUMN_RES | 0.089 | 0.850 | 88.400R |
PVDDCIMEMGPU_ISUMP | 0.584 | – | – |
PVDDCIMEMGPU_ISUMP_RES | 0.089 | 0.850 | 88.400R |
PVDDCIMEMGPU_PGOOD | 0.584 | – | – |
PVDDCIMEMGPU_PHASE | 0.089 | 0.850 | 31.000R |
PVDDCIMEMGPU_VSEN | 0.307 | – | – |
PVDDCIMEMGPU_VSEN_C | 0.308 | – | – |
PVDDCOREGPU_EN | 0.572 | – | – |
PVDDCOREGPU_VRHOT_L | 0.480 | – | – |
PVDDCPUAWAKE_FB | 0.000 | – | – |
PVDDCPUAWAKE_FB_R | 0.000 | – | – |
PVDDCPUAWAKE_SW0 | 0.032 | 1.060 | 31.900R |
PVDDCPUAWAKE_SW1 | 0.032 | 1.060 | 31.900R |
PVDDCPUAWAKE_SW2 | 0.032 | 1.060 | 31.900R |
PVDDCPUAWAKE_SW3 | 0.032 | 1.060 | 31.900R |
PVDDCPUSRAMAWAKE_FB | 0.000 | – | – |
PVDDCPUSRAMAWAKE_SW0 | 0.355 | 1.060 | 353.000 |
PVDDCRGFXGPU_IMON_FB | OL | – | – |
PVDDCRGFXGPU_IMON_R | OL | – | – |
PVDDCRGFXGPU_PGOOD | 0.575 | – | – |
PVDDCRSOCGPU_FB_R | OL | – | – |
PVDDCRSOCGPU_IMON_R | OL | – | – |
PVDDCRSOCGPU_PGOOD | 0.575 | – | – |
PVDDIOMEMGPU_ISNS1_N | 0.048 | 1.350 | 46.600R |
PVDDIOMEMGPU_ISNS1_P | 0.048 | 1.350 | 46.600R |
PVDDIOMEMGPU_ISNS2_N | 0.048 | 1.350 | 46.600R |
PVDDIOMEMGPU_ISNS2_P | 0.048 | 1.350 | 46.600R |
PVDDIOMEMGPU_LGATE1 | 0.466 | – | – |
PVDDIOMEMGPU_LGATE2 | 0.467 | – | – |
PVDDIOMEMGPU_PGOOD | 0.584 | – | – |
PVDDIOMEMGPU_PHASE1 | 0.048 | – | 38.000R |
PVDDIOMEMGPU_PHASE2 | 0.048 | – | 38.000R |
PVDDIOMEMGPU_UGATE1 | 0.512 | – | – |
PVDDIOMEMGPU_UGATE2 | 0.513 | – | – |
PVDDIOMEMGPU_UGATE2_R | 0.513 | – | – |
PVDDMEMGPU_EN | 0.575 | – | – |
PVDDMEMGPU_FCCM | 0.624 | – | – |
PVDDMEMGPU_RTN | 0.007 | – | 3.300R |
PVDDQ_EN | 0.735 | – | – |
PVDDQ_EN_LED | OL | – | – |
PVDDQ_EN_R | 0.501 | – | – |
PVDDQ_PGOOD | 0.576 | – | – |
PVIN_RFLDO_WLANBT_VLX | 0.328 | 1.800 | 0.100R |
PVPP_EN_R | OL | – | – |
PVTT_VTTSNS | 0.134 | – | – |
REG_FB_P2V5S3 | 1.405 | – | – |
REG_PHASE_2V5S3 | 0.420 | 2.500 | – |
REG_VOS_P2V5S3 | 0.428 | – | – |
RSLOC_RST_L | 0.490 | – | – |
SA_ISUMN_R | 1.027 | – | – |
SAVE_BAT_G | 0.757 | – | – |
SAVE_BAT_S | 1.568 | – | – |
SE_CTLR_FW_DWLD | 0.479 | – | – |
SE_DEV_WAKE | 0.482 | – | – |
SE_GPIO2_AO | 0.756 | – | – |
SE_GPIO3_AO | 0.756 | – | – |
SE_PWR_EN | 0.765 | – | – |
SE_RXN | 0.496 | – | – |
SE_RXP | 0.496 | – | – |
SE_XTAL1 | 0.542 | – | – |
SENSOR_PWR_EN | 0.416 | – | – |
SMC_BMON_ISENSE | 0.791 | – | – |
SMC_DCIN_ISENSE | 0.808 | 0.400 | – |
SMC_DCIN_VSENSE | 0.807 | – | – |
SMC_DEBUGPRT_RX | 0.461 | – | – |
SMC_DEBUGPRT_TX | 0.479 | – | – |
SMC_FAN_0_PWM | 0.492 | – | – |
SMC_FAN_0_TACH | 0.457 | – | – |
SMC_FAN_1_PWM | 0.488 | – | – |
SMC_FAN_1_TACH | 0.461 | – | – |
SMC_FIXTURE_MODE_L | 0.490 | – | – |
SMC_P3V3_CAPLE_ISENSE | 0.806 | – | – |
SMC_PBUS_VSENSE | 0.806 | 1.000 | – |
SMC_PCH_PWROK | 0.461 | – | – |
SMC_PCH_SYS_PWROK | 0.461 | – | – |
SMC_PECI_TX | 0.476 | – | – |
SMC_PECI_TX_R | 0.450 | – | – |
SMC_PROCHOT_L | 0.469 | – | – |
SMC_RSMRST_L | 0.452 | – | – |
SMC_SYSRST_L | 0.461 | – | – |
SMCRST_TIEOFF | 0.720 | – | – |
SOC_AMBER_R | OL | – | – |
SOC_BLUE_AWAKE | OL | – | – |
SOC_BLUE_R | OL | – | – |
SOC_COLD_RESET_L | 0.494 | – | – |
SOC_DEBUGPRT_RX | 0.490 | – | – |
SOC_DEBUGPRT_TX | 0.489 | – | – |
SOC_DFU_STATUS | 0.534 | – | – |
SOC_DOCK_CONNECT | 0.461 | – | – |
SOC_FORCE_DFU | 0.490 | – | – |
SOC_GREEN_DDR | OL | – | – |
SOC_GREEN_R | OL | – | – |
SOC_PCIE_UP_REXT | 0.786 | – | – |
SOC_PERST_L | 0.485 | – | – |
SOC_PM_THRMTRIP_L | 0.771 | – | – |
SOC_PM_THRMTRIP_L_R | 0.713 | – | – |
SOC_RED_R | OL | – | – |
SOC_RED_SLPS2R | OL | – | – |
SOC_SOCHOT_L | 0.490 | – | – |
SOC_SWD_MUX_SEL_PCH | 0.576 | – | – |
SOC_USB_VBUS | 0.420 | – | – |
SOC_VDDCPU_SENSE | 0.478 | – | – |
SOC_WDOG | 0.492 | – | – |
SPARE_UPC_TA_USB2_RN | 0.704 | – | – |
SPARE_UPC_TA_USB2_RP | 0.701 | – | – |
SPARE_UPC_TA_USB3_RN | 0.704 | – | – |
SPARE_UPC_TA_USB3_RP | 0.701 | – | – |
SPARE_UPC_TB_USB2_RN | 0.701 | – | – |
SPARE_UPC_TB_USB2_RP | 0.701 | – | – |
SPARE_UPC_TB_USB3_RN | 0.701 | – | – |
SPARE_UPC_TB_USB3_RP | 0.701 | – | – |
SPARE_UPC_XA_USB3_RN | 0.735 | – | – |
SPARE_UPC_XA_USB3_RP | 0.733 | – | – |
SPARE_UPC_XB_USB2_RN | 0.705 | – | – |
SPARE_UPC_XB_USB2_RP | 0.704 | – | – |
SPARE_UPC_XB_USB3_RN | 0.706 | – | – |
SPARE_UPC_XB_USB3_RP | 0.704 | – | – |
SPI_AOP_MA781_CLK | 0.520 | – | – |
SPI_AOP_MA781_CS_L | 0.496 | – | – |
SPI_AOP_MA781_MISO | 0.518 | – | – |
SPI_AOP_MA781_MOSI | 0.520 | – | – |
SPI_AOP_SENSOR_CLK_R | 0.489 | – | – |
SPI_AOP_SENSOR_MISO | 0.495 | – | – |
SPI_DFR_CLK | 0.502 | – | – |
SPI_DFR_CS_L | 0.460 | – | – |
SPI_DFR_MISO | 0.495 | – | – |
SPI_DFR_MISO_R | 0.502 | – | – |
SPI_DFR_MOSI | 0.485 | – | – |
SPI_IO<2> | 0.800 | – | – |
SPI_IO2_STRAP_L | 0.730 | – | – |
SPI_MESA_CLK_CONN | 0.569 | – | – |
SPI_MESA_MISO | 0.492 | – | – |
SPI_MESA_MISO_CONN | 0.493 | – | – |
SPI_MESA_MOSI | 0.511 | – | – |
SPI_MESA_MOSI_CONN | 0.513 | – | – |
SPI_MOSI_R | 0.814 | – | – |
SPI_MOSI_R_CONN | 1.125 | – | – |
SPI_SOCROM_CLK | 0.460 | 0.500 | – |
SPI_SOCROM_CS_L | 0.493 | 1.800 | – |
SPI_SOCROM_MISO | 0.433 | 0.645 | – |
SPI_SOCROM_MISO_R | 0.424 | 0.414 | – |
SPI_SOCROM_MOSI | 0.472 | 1.800 | – |
SPI_SOCROM_MOSI_R | 0.450 | – | – |
SPI_SOCROM_WP_L | 0.553 | 1.800 | – |
SPI_TPAD_CLK | 0.504 | – | – |
SPI_TPAD_CLK_CONN | 0.703 | – | – |
SPI_TPAD_CS_CONN_L | 0.682 | – | – |
SPI_TPAD_CS_L | 0.477 | – | – |
SPI_TPAD_EN_CONN | 0.490 | – | – |
SPI_TPAD_INT_CONN_L | 0.495 | – | – |
SPI_TPAD_MISO | 0.487 | – | – |
SPI_TPAD_MISO_CONN | 0.684 | – | – |
SPI_TPAD_MISO_R | 0.506 | – | – |
SPI_TPAD_MOSI | 0.505 | – | – |
SPI_TPAD_MOSI_CONN | 0.702 | – | – |
SPI_TPAD3V3_CLK_R | 0.680 | – | – |
SPI_TPAD3V3_MOSI_R | 0.678 | – | – |
SPKRAMP_INT_L | 0.356 | – | – |
SPKRAMP_LT_AREG | 0.587 | – | – |
SPKRAMP_LT_BSTN | 0.778 | – | – |
SPKRAMP_LT_BSTP | 0.778 | – | – |
SPKRAMP_LT_DREG | 0.524 | – | – |
SPKRAMP_LT_MODE | 0.473 | – | – |
SPKRAMP_LT_OUTN | 0.470 | – | 0.281R |
SPKRAMP_LT_OUTP | 0.470 | – | 0.283R |
SPKRAMP_LW1_AREG | 0.584 | – | – |
SPKRAMP_LW1_BSTN | 0.778 | – | – |
SPKRAMP_LW1_BSTP | 0.778 | – | – |
SPKRAMP_LW1_DREG | 0.523 | – | – |
SPKRAMP_LW1_MODE | 0.000 | – | – |
SPKRAMP_LW1_OUTN | 0.480 | – | 0.287R |
SPKRAMP_LW1_OUTP | 0.480 | – | 0.287R |
SPKRAMP_LW2_AREG | 0.587 | – | – |
SPKRAMP_LW2_BSTN | 0.778 | – | – |
SPKRAMP_LW2_BSTP | 0.778 | – | – |
SPKRAMP_LW2_DREG | 0.524 | – | – |
SPKRAMP_LW2_MODE | 0.407 | – | – |
SPKRAMP_LW2_OUTN | 0.480 | – | 0.295R |
SPKRAMP_LW2_OUTP | 0.480 | – | 0.293R |
SPKRAMP_RESET_L | 0.355 | – | – |
SPKRAMP_RT_AREG | 0.590 | – | – |
SPKRAMP_RT_BSTN | 0.775 | – | – |
SPKRAMP_RT_BSTP | 0.775 | – | – |
SPKRAMP_RT_DREG | 0.525 | – | – |
SPKRAMP_RT_MODE | 0.474 | – | – |
SPKRAMP_RT_OUTN | 0.485 | – | 0.281R |
SPKRAMP_RT_OUTP | 0.484 | – | 0.285R |
SPKRAMP_RW1_AREG | 0.583 | – | – |
SPKRAMP_RW1_BSTN | 0.775 | – | – |
SPKRAMP_RW1_BSTP | 0.775 | – | – |
SPKRAMP_RW1_MODE | 0.014 | – | 13.000R |
SPKRAMP_RW1_OUTN | 0.484 | – | 0.290R |
SPKRAMP_RW1_OUTP | 0.485 | – | 0.291R |
SPKRAMP_RW2_AREG | 0.583 | – | – |
SPKRAMP_RW2_BSTN | 0.775 | – | – |
SPKRAMP_RW2_BSTP | 0.775 | – | – |
SPKRAMP_RW2_DREG | 0.523 | – | – |
SPKRAMP_RW2_MODE | 0.405 | – | – |
SPKRAMP_RW2_OUTN | 0.478 | – | 0.279R |
SPKRAMP_RW2_OUTP | 0.480 | – | 0.282R |
SPKRCONN_LT_OUTN | 0.470 | – | 0.281R |
SPKRCONN_LT_OUTP | 0.470 | – | 0.283R |
SPKRCONN_LW1_OUTN | 0.480 | – | 0.287R |
SPKRCONN_LW1_OUTP | 0.480 | – | 0.287R |
SPKRCONN_LW2_OUTN | 0.480 | – | 0.295R |
SPKRCONN_LW2_OUTP | 0.480 | – | 0.293R |
SPKRCONN_RT_OUTN | 0.485 | – | 0.281R |
SPKRCONN_RT_OUTP | 0.484 | – | 0.285R |
SPKRCONN_RW1_OUTN | 0.484 | – | 0.290R |
SPKRCONN_RW1_OUTP | 0.485 | – | 0.291R |
SPKRCONN_RW2_OUTN | 0.478 | – | 0.279R |
SPKRCONN_RW2_OUTP | 0.480 | – | 0.282R |
SPMI_DATA | 0.418 | – | – |
SPMI_DATA_R | 0.438 | – | – |
SPROM_CLK | 0.500 | – | – |
SPROM_CS | 0.496 | – | – |
SPROM_CS_R | 0.573 | – | – |
SPROM_DIN | 0.514 | – | – |
SPROM_DOUT | 0.501 | – | – |
SSD_PMU_RESET_L | – | 1.80 | – |
SSD0_CLK24M | 0.454 | – | – |
SSD0_CLK24M_23 | 0.000 | – | – |
SSD0_CLKREQ3_L | 0.483 | – | – |
SSD0_OCARINA_FORCE_EN | 0.571 | – | – |
SSD0_OCARINA_IREF | 0.750 | – | – |
SSD0_OCARINA_NAND_VCC_DET | 0.763 | – | – |
SSD0_OCARINA_PFN | – | 1.80 | – |
SSD0_OCARINA_POK2 | 0.000 | – | – |
SSD0_OCARINA_TCAL | 0.777 | – | – |
SSD0_OCARINA_TDEV1 | 0.773 | – | – |
SSD0_OCARINA_TDEV2 | 0.771 | – | – |
SSD0_OCARINA_VDD_LDO | 0.369 | – | – |
SSD0_OCARINA_VREF | 0.772 | – | – |
SSD0_OCARINA_WP_L | – | 1.80 | – |
SSD0_S4E_BOOT2 | 0.446 | – | – |
SSD0_S4E0_PCIE_RESREF | 0.788 | – | – |
SSD0_S4E0_SWD_UID0 | 0.499 | – | – |
SSD0_S4E0_SWD_UID1 | 0.498 | – | – |
SSD0_S4E0_UART_TX | 0.499 | – | – |
SSD0_S4E0_VPP | 0.571 | – | – |
SSD0_S4E0_ZQ_L | 0.302 | – | – |
SSD0_S4E3_DROOP_L | 0.524 | – | – |
SSD0_S4E3_PCIE_RESREF | 0.790 | – | – |
SSD0_S4E3_SWD_UID0 | 0.517 | – | – |
SSD0_S4E3_SWD_UID1 | 0.517 | – | – |
SSD0_S4E3_UART_TX | 0.517 | – | – |
SSD0_S4E3_ZQ_L | 0.301 | – | – |
SSD0_STG01_ADDR | 0.572 | – | – |
SSD0_TPS62180_FB | 1.422 | – | – |
SSD0_TPS62180_FB_R | 0.418 | – | – |
SSD0_TPS62180_SS | 0.540 | – | – |
SSD0_VR_P2V5_EN | 0.647 | – | – |
SSD0_VR_P2V5_EN_R | – | 1.800 | – |
SSD0_VR_P2V5_PGOOD | 0.565 | – | – |
SSD1_CLK24M_01 | 0.490 | – | – |
SSD1_OCARINA_FORCE_EN | 0.569 | – | – |
SSD1_OCARINA_IREF | 0.750 | – | – |
SSD1_OCARINA_PGOOD | 0.761 | – | – |
SSD1_OCARINA_POK2 | 0.000 | – | – |
SSD1_OCARINA_TCAL | 0.776 | – | – |
SSD1_OCARINA_TDEV1 | 0.777 | – | – |
SSD1_OCARINA_TDEV2 | 0.776 | – | – |
SSD1_OCARINA_VDD_LDO | 0.369 | – | – |
SSD1_OCARINA_VREF | 0.771 | – | – |
SSD1_S4E0_JTAG_TDI | 0.508 | – | – |
SSD1_S4E0_UART_TX | 0.495 | – | – |
SSD1_S4E1_UART_TX | OL | – | – |
SSD1_TPS62180_FB | 1.417 | – | – |
SSD1_TPS62180_FB_R | 0.438 | – | – |
SSD1_TPS62180_SS | 0.539 | – | – |
SSD1_VR_P2V5_EN | 0.650 | – | – |
SSD1_VR_P2V5_EN_R | 0.650 | – | – |
SSD1_VR_P2V5_PGOOD | 0.562 | – | – |
SSTATE_BLUE | OL | – | – |
SSTATE_BLUE_R | OL | – | – |
SSTATE_GREEN | OL | – | – |
SSTATE_GREEN_R | OL | – | – |
SSTATE_RED | OL | – | – |
SSTATE_RED_R | OL | – | – |
SVID_PWROK | 0.528 | – | – |
SVID_PWROK_CONN | OL | – | – |
SWD_SOC_SWCLK | 0.464 | – | – |
SWD_SOC_SWDIO | 0.464 | – | – |
SYS_DETECT | OL | – | – |
SYS_DETECT_L | 0.515 | – | – |
TBT_POC_RESET | 0.540 | – | – |
TBT_PWR_EN | 0.542 | – | – |
TBT_T_BATLOW_L | 0.604 | – | – |
TBT_T_CIO_PWR_EN | 0.517 | – | – |
TBT_T_CLKREQ_L | 0.811 | – | – |
TBT_T_CLKREQ_R_L | 0.602 | – | – |
TBT_T_HDMI_DDC_CLK | 0.602 | – | – |
TBT_T_HDMI_DDC_DATA | 0.563 | – | – |
TBT_T_PCI_RESET_L | 0.551 | – | – |
TBT_T_PLUG_EVENT_L | 0.542 | – | – |
TBT_T_PWR_EN_U8295 | 0.544 | – | – |
TBT_T_RBIAS | 0.781 | – | – |
TBT_T_ROM_HOLD_L | 0.680 | – | – |
TBT_T_ROM_WP_L | 0.560 | – | – |
TBT_T_RSENSE | 0.000 | – | – |
TBT_T_SPI_CLK | 0.540 | – | – |
TBT_T_SPI_CLK_DBG | 0.602 | – | – |
TBT_T_SPI_CS_L | 0.560 | – | – |
TBT_T_SPI_MISO | 0.560 | – | – |
TBT_T_SPI_MOSI | 0.560 | – | – |
TBT_T_TEST_EN | 0.101 | – | – |
TBT_T_TEST_PWR_GOOD | 0.101 | – | – |
TBT_T_TMU_CLK_IN | 0.601 | – | – |
TBT_T_TMU_CLK_OUT | 0.604 | – | – |
TBT_T_USB_PWR_EN | 0.554 | – | – |
TBT_T_XTAL25M_IN | 0.836 | – | – |
TBT_T_XTAL25M_OUT | 0.782 | – | – |
TBT_TA_USB2_MXCTL | 0.602 | – | – |
TBT_TA_USB2_RBIAS | 0.202 | – | – |
TBT_TB_USB2_MXCTL | 0.601 | – | – |
TBT_TB_USB2_RBIAS | 0.000 | – | – |
TBT_WAKE_3V3_L | 0.535 | – | – |
TBT_X_CIO_PWR_EN | 0.540 | – | – |
TBT_X_HDMI_DDC_CLK | 0.609 | – | – |
TBT_X_HDMI_DDC_DATA | 0.574 | – | – |
TBT_X_PCI_RESET_L | 0.554 | – | – |
TBT_X_PCIE_BIAS | 0.790 | – | – |
TBT_X_PLUG_EVENT_L | 0.564 | – | – |
TBT_X_PWR_EN_U8297 | 0.541 | – | – |
TBT_X_RBIAS | 0.780 | – | – |
TBT_X_ROM_HOLD_L | 0.681 | – | – |
TBT_X_ROM_WP_L | 0.566 | – | – |
TBT_X_RSENSE | 0.000 | – | – |
TBT_X_RTD3_PWR_EN | 0.609 | – | – |
TBT_X_SPI_CLK | 0.548 | – | – |
TBT_X_SPI_CS_L | 0.570 | – | – |
TBT_X_SPI_DBG_CLK | OL | – | – |
TBT_X_SPI_DBG_CS_L | OL | – | – |
TBT_X_SPI_DBG_MISO | OL | – | – |
TBT_X_SPI_DBG_MOSI | OL | – | – |
TBT_X_SPI_MISO | 0.571 | – | – |
TBT_X_SPI_MOSI | 0.574 | – | – |
TBT_X_TMU_CLK_IN | 0.611 | – | – |
TBT_X_USB_PWR_EN | 0.552 | – | – |
TBT_X_XTAL25M_IN | 0.835 | – | – |
TBT_X_XTAL25M_OUT | 0.786 | – | – |
TBTTHMSNS_T_D1_N | 0.000 | – | – |
TBTTHMSNS_T_D1_P | 0.620 | – | – |
TBTTHMSNS_X_D1_N | 0.000 | – | – |
TBTTHMSNS_X_D1_P | 0.633 | – | – |
TP_BMON_IOUT | OL | – | – |
TP_BT_GPIO_4 | 0.712 | – | – |
TP_CHGR_EN_VR1 | – | 5.000 | – |
TP_CHGR_SMC_RST_L | – | 1.800 | – |
TP_CPU_RSVD_TP_BT2 | 0.341 | – | – |
TP_CPU_RSVD_TP_D1 | 0.236 | – | – |
TP_CPU_RSVD_TP75 | 0.337 | – | – |
TP_CPU_RSVD_TP76 | 0.236 | – | – |
TP_DFR_TOUCH_PANEL_DETECT | OL | – | – |
TP_DFR_TOUCH_ROM_WC | OL | – | – |
TP_DFR_TOUCH_RSVD | OL | – | – |
TP_GPU_A1_DETECT | OL | – | – |
TP_GPU_BAMACO_EN | 0.404 | – | – |
TP_HDA_RST | 0.821 | – | – |
TP_HDA_SDI1 | 0.822 | – | – |
TP_HDA_SDO | 0.822 | – | – |
TP_ISNS_SKPRLN | OL | – | – |
TP_ISNS_SKPRLP | OL | – | – |
TP_JTAG_SOC_TDI | 0.497 | – | – |
TP_JTAG_SOC_TDO | 0.494 | – | – |
TP_PCH_STRP_TOPBLK_SWP_L | 0.828 | – | – |
TP_PCH_TP1_F22 | 0.785 | – | – |
TP_PCH_TP3_B24 | 0.837 | – | – |
TP_SOC_TST_CLKOUT | 0.486 | – | – |
TP_SSD0_S4E0_ANI0_VREF | 0.776 | – | – |
TP_SSD0_S4E0_ANI1_VREF | 0.775 | – | – |
TP_SSD0_S4E1_ANI0_VREF | 0.774 | – | – |
TP_SSD0_S4E1_ANI1_VREF | 0.774 | – | – |
TP_SSD0_S4E2_ANI1_VREF | 0.776 | – | – |
TP_SSD0_S4E3_ANI0_VREF | 0.770 | – | – |
TP_SSD0_S4E3_ANI1_VREF | 0.774 | – | – |
TP_UPC_TA_GPIO9 | 0.691 | – | – |
TP_UPC_TA_GPIO10 | 0.693 | – | – |
TP_UPC_TB_GPIO9 | 0.687 | – | – |
TP_UPC_TB_GPIO10 | 0.691 | – | – |
TP_USBC_PP20V_TA | OL | – | – |
TP_USBC_PP20V_TB | OL | – | – |
TP_USBC_PP20V_XA | OL | – | – |
TP_USBC_PP20V_XB | OL | – | – |
TP_USBC_TB_RESET_L | 0.641 | – | – |
TP_USBC_XA_RESET_L | 0.678 | – | – |
TPAD_KBD_WAKE_L | 0.494 | – | – |
TPAD_SPI_EN | 0.490 | – | – |
TPAD_SPI_INT_L | 0.493 | – | – |
TSNS_T1_DX1_N | 0.000 | – | – |
TSNS_T1_DX1_P | 0.647 | – | – |
TSNS_T1_DX2_N | 0.000 | – | – |
TSNS_T1_DX2_P | 0.649 | – | – |
TSNS_T1_DX5_N | 0.000 | – | – |
TSNS_T1_DX5_P | 0.650 | – | – |
TSNS_T1_DX7_N | 0.000 | – | – |
TSNS_T1_DX7_P | 0.648 | – | – |
U4800_PIN4 | 0.687 | – | – |
U6801_PWR_EN | 0.300 | – | – |
UART_BT_BUF_CTS_L | 0.481 | – | – |
UART_BT_BUF_D2R | 0.449 | – | – |
UART_BT_BUF_R2D | 0.481 | – | – |
UART_BT_BUF_RTS_L | 0.448 | – | – |
UART_BT_LH_D2R | 0.487 | – | – |
UART_SE_D2R | 0.480 | – | – |
UART_SE_D2R_CTS_L | 0.479 | – | – |
UART_SE_R2D | 0.455 | – | – |
UART_SE_R2D_RTS_L | 0.455 | – | – |
UART_WLAN_D2R | 0.489 | – | – |
UART_WLAN_D2R_CTS_L | 0.488 | – | – |
UPC_DBG_T | 0.545 | – | – |
UPC_I2C_INT_L | 0.457 | 1.800 | – |
UPC_PMU_RESET | 0.540 | – | – |
UPC_T_5V_EN | 0.590 | – | – |
UPC_T_5V_EN_R | 0.566 | – | – |
UPC_T_SPI_CLK | 0.568 | – | – |
UPC_T_SPI_CS_L | 0.591 | – | – |
UPC_T_SPI_MISO | 0.592 | – | – |
UPC_T_SPI_MOSI | 0.595 | – | – |
UPC_TA_DBG0 | 0.677 | – | – |
UPC_TA_DBG1 | 0.667 | – | – |
UPC_TA_FAULT_L | 0.625 | – | – |
UPC_TA_GPIO1 | 0.637 | – | – |
UPC_TA_GPIO7 | 0.690 | – | – |
UPC_TA_R_OSC | 0.458 | – | – |
UPC_TA_SER_DBG | 0.628 | – | – |
UPC_TA_SPI_CLK | 0.549 | – | – |
UPC_TA_SPI_CS_L | 0.685 | – | – |
UPC_TA_SPI_MISO | 0.569 | – | – |
UPC_TA_SPI_MOSI | 0.573 | – | – |
UPC_TA_SS | 0.557 | – | – |
UPC_TA_SWD_CLK | 0.571 | 3.300 | – |
UPC_TA_SWD_DATA | 0.677 | 3.300 | – |
UPC_TA_UART_RX | 0.531 | 3.400 | – |
UPC_TA_UART_TX | 0.530 | 3.400 | – |
UPC_TB_FAULT_L | 0.627 | – | – |
UPC_TB_GPIO1 | 0.634 | – | – |
UPC_TB_GPIO7 | 0.691 | – | – |
UPC_TB_R_OSC | 0.452 | – | – |
UPC_TB_SER_DBG | 0.633 | – | – |
UPC_TB_SS | 0.555 | – | – |
UPC_TB_SWD_CLK | 0.569 | 3.300 | – |
UPC_TB_SWD_DATA | 0.673 | 3.300 | – |
UPC_X_5V_EN | 0.588 | – | – |
UPC_X_5V_EN_R | 0.533 | – | – |
UPC_X_SPI_CLK | 0.576 | – | – |
UPC_X_SPI_MOSI | 0.566 | – | – |
UPC_XA_DBG_PD | 0.663 | – | – |
UPC_XA_FAULT_L | 0.690 | – | – |
UPC_XA_R_OSC | 0.474 | – | – |
UPC_XA_SER_DBG | 0.638 | – | – |
UPC_XA_SWD_CLK | 0.607 | – | – |
UPC_XA_SWD_DATA | 0.718 | – | – |
UPC_XA_UART_RX | 0.535 | – | – |
UPC_XA_UART_TX | 0.535 | – | – |
UPC_XB_DBG4 | 0.464 | – | – |
UPC_XB_DBG5 | 0.464 | – | – |
UPC_XB_FAULT_L | 0.655 | – | – |
UPC_XB_GPIO1 | 0.634 | – | – |
UPC_XB_GPIO4 | 0.640 | – | – |
UPC_XB_GPIO9 | 0.684 | – | – |
UPC_XB_GPIO10 | 0.688 | – | – |
UPC_XB_R_OSC | 0.454 | – | – |
UPC_XB_SER_DBG | 0.640 | – | – |
UPC_XB_SPI_CLK | 0.555 | – | – |
UPC_XB_SPI_CS_L | 0.577 | – | – |
UPC_XB_SPI_MISO | 0.579 | – | – |
UPC_XB_SPI_MOSI | 0.581 | – | – |
UPC_XB_SS | 0.557 | – | – |
UPC_XB_SWD_CLK | 0.570 | – | – |
UPC_XB_SWD_DATA | 0.670 | – | – |
USB_SOC_N | 0.722 | – | – |
USB_SOC_P | 0.721 | – | – |
USB_UPC_PCH_TA_F_N | 0.436 | – | – |
USB_UPC_PCH_TA_F_P | 0.438 | – | – |
USB_UPC_PCH_TA_N | 0.486 | – | – |
USB_UPC_PCH_TA_P | 0.488 | – | – |
USB_UPC_PCH_TB_F_N | 0.440 | – | – |
USB_UPC_PCH_TB_F_P | 0.440 | – | – |
USB_UPC_PCH_TB_N | 0.487 | – | – |
USB_UPC_PCH_TB_P | 0.493 | – | – |
USB_UPC_PCH_XA_F_N | 0.489 | – | – |
USB_UPC_PCH_XA_F_P | 0.490 | – | – |
USB_UPC_PCH_XA_N | 0.489 | – | – |
USB_UPC_PCH_XA_P | 0.490 | – | – |
USB_UPC_PCH_XB_N | 0.493 | – | – |
USB_UPC_PCH_XB_P | 0.491 | – | – |
USB_UPC_XB_F_N | 0.442 | – | – |
USB_UPC_XB_F_P | 0.445 | – | – |
USB3_EXTA_D2R_N | 0.327 | – | – |
USB3_EXTA_D2R_P | 0.322 | – | – |
USB3_EXTA_R2D_C_N | 0.314 | – | – |
USB3_EXTA_R2D_C_P | 0.314 | – | – |
USB3_EXTA_R2D_N | 0.682 | – | – |
USB3_EXTA_R2D_P | 0.668 | – | – |
USB3_TEST_D2R_N | 0.325 | – | – |
USB3_TEST_D2R_P | 0.325 | – | – |
USB3_TEST_R2D_N | 0.309 | – | – |
USB3_TEST_R2D_P | 0.309 | – | – |
USB3_TEST2_D2R_N | 0.328 | – | – |
USB3_TEST2_D2R_P | 0.327 | – | – |
USB3_TEST2_R2D_N | 0.308 | – | – |
USB3_TEST2_R2D_P | 0.309 | – | – |
USBC_T_RESET_L | 0.630 | – | – |
USBC_TA_CC1 | 0.590 | – | – |
USBC_TA_CC2 | 0.594 | – | – |
USBC_TA_D2R_CR_N<1> | OL | – | – |
USBC_TA_D2R_CR_N<2> | OL | – | – |
USBC_TA_D2R_CR_P<1> | OL | – | – |
USBC_TA_D2R_CR_P<2> | OL | – | – |
USBC_TA_R2D_N<1> | OL | – | – |
USBC_TA_R2D_N<2> | OL | – | – |
USBC_TA_R2D_P<1> | OL | – | – |
USBC_TA_R2D_P<2> | OL | – | – |
USBC_TA_SBU1 | 0.661 | – | – |
USBC_TA_SBU2 | 0.660 | – | – |
USBC_TA_USB_BOT_N | 0.766 | – | – |
USBC_TA_USB_BOT_P | 0.770 | – | – |
USBC_TA_USB_TOP_N | 0.768 | – | – |
USBC_TA_USB_TOP_P | 0.770 | – | – |
USBC_TB_CC1 | 0.590 | – | – |
USBC_TB_CC2 | 0.590 | – | – |
USBC_TB_D2R_CR_N<1> | OL | – | – |
USBC_TB_D2R_CR_N<2> | OL | – | – |
USBC_TB_D2R_CR_P<1> | OL | – | – |
USBC_TB_D2R_CR_P<2> | OL | – | – |
USBC_TB_R2D_N<2> | OL | – | – |
USBC_TB_R2D_P<1> | OL | – | – |
USBC_TB_R2D_P<2> | OL | – | – |
USBC_TB_SBU1 | 0.660 | – | – |
USBC_TB_SBU2 | 0.660 | – | – |
USBC_TB_USB_BOT_N | 0.766 | – | – |
USBC_TB_USB_BOT_P | 0.770 | – | – |
USBC_TB_USB_TOP_N | 0.768 | – | – |
USBC_TB_USB_TOP_P | 0.770 | – | – |
USBC_X_RESET_L | 0.637 | – | – |
USBC_XA_CC1 | 0.595 | – | – |
USBC_XA_CC2 | 0.594 | – | – |
USBC_XA_D2R_CR_N<1> | OL | – | – |
USBC_XA_D2R_CR_P<1> | 0.773 | – | – |
USBC_XA_D2R_CR_P<2> | OL | – | – |
USBC_XA_R2D_N<1> | 0.663 | – | – |
USBC_XA_R2D_N<2> | OL | – | – |
USBC_XA_R2D_P<1> | 0.663 | – | – |
USBC_XA_R2D_P<2> | OL | – | – |
USBC_XA_SBU1 | 0.662 | – | – |
USBC_XA_SBU2 | OL | – | – |
USBC_XA_USB_BOT_N | 0.770 | – | – |
USBC_XA_USB_BOT_P | 0.772 | – | – |
USBC_XA_USB_TOP_N | OL | – | – |
USBC_XA_USB_TOP_P | OL | – | – |
USBC_XB_CC1 | 0.590 | – | – |
USBC_XB_CC2 | 0.566 | – | – |
USBC_XB_D2R_CR_N<1> | OL | – | – |
USBC_XB_D2R_CR_N<2> | 0.771 | – | – |
USBC_XB_D2R_CR_P<1> | OL | – | – |
USBC_XB_D2R_CR_P<2> | 0.773 | – | – |
USBC_XB_R2D_N<1> | OL | – | – |
USBC_XB_R2D_N<2> | 0.600 | – | – |
USBC_XB_R2D_P<1> | OL | – | – |
USBC_XB_SBU1 | OL | – | – |
USBC_XB_SBU2 | 0.669 | – | – |
USBC_XB_USB_BOT_N | 0.770 | – | – |
USBC_XB_USB_BOT_P | 0.771 | – | – |
USBC_XB_USB_TOP_N | OL | – | – |
USBC_XB_USB_TOP_P | OL | – | – |
USFF_MEM_OK | 0.815 | – | – |
UVP_DIS_L | 0.555 | – | – |
VR0V9_IND_TBT_T | 0.288 | 0.900 | 286.000 |
VR0V9_IND_TBT_X | 0.320 | 0.900 | 312.000R |
VSNS_PP0V82_SLPDDR_NEG | 0.000 | – | – |
VSNS_PP0V82_SLPDDR_POS | 0.049 | – | 49.000R |
VSNS_PP1V2_S3_CPUDDR_NEG | – | – | 0.000R |
VSNS_PP1V2_S3_CPUDDR_POS | 0.220 | 1.200 | 226.000 |
VSNS_PP1V2_S3_NEG | 0.000 | – | – |
VSNS_PP1V2_S3_POS | 0.220 | 1.200 | 221.000 |
VSNS_PP1V05_PRIM_NEG | 0.000 | – | 0.800R |
VSNS_PP1V05_PRIM_POS | 0.099 | – | 98.000R |
VSNS_PP1V8_S0_GPU_REG_NEG | 0.000 | – | – |
VSNS_PP1V8_S0_GPU_REG_POS | 0.186 | – | – |
VSNS_PP1V8_SLPS2R_NEG | 0.000 | – | – |
VSNS_PP1V8_SLPS2R_POS | 0.407 | – | – |
VSNS_PP2V5_NAND_SSD0_NEG | 0.000 | – | – |
VSNS_PP2V5_NAND_SSD0_POS | 0.408 | – | – |
VSNS_PP2V5_NAND_SSD1_NEG | 0.000 | – | – |
VSNS_PP2V5_NAND_SSD1_POS | 0.430 | – | – |
VSNS_PP3V3_G3H_RTC_X_NEG | 0.000 | – | – |
VSNS_PP3V3_G3H_RTC_X_POS | 0.419 | – | – |
VSNS_PP3V3_G3H_T_NEG | 0.000 | – | – |
VSNS_PP3V3_G3H_T_POS | 0.378 | – | – |
VSNS_PP5V_G3S_NEG | 0.000 | – | – |
VSNS_PP5V_G3S_POS | 0.403 | – | – |
VSNS_PPBUS_HS_CPU_NEG | 0.000 | – | – |
VSNS_PPBUS_HS_CPU_POS | 0.413 | – | – |
VSNS_PPBUS_HS_OTH5V_NEG | 0.000 | – | – |
VSNS_PPBUS_HS_OTH5V_POS | 0.414 | – | – |
VSNS_PPVCC_S0_CPU_NEG | 0.000 | – | – |
VSNS_PPVCC_S0_CPU_POS | 0.002 | – | – |
VSNS_PPVCCGT_S0_CPU_NEG | 0.000 | – | – |
VSNS_PPVCCGT_S0_CPU_POS | 0.006 | – | – |
VSNS_PPVCCIO_S0_CPU_NEG | 0.000 | – | 1.000R |
VSNS_PPVCCIO_S0_CPU_POS | 0.069 | 0.950 | 75.000R |
VSNS_PPVCCPRIMCORE_PRIM_REG_NEG | 0.000 | – | – |
VSNS_PPVCCPRIMCORE_PRIM_REG_POS | 0.103 | – | – |
VSNS_PPVCCSA_S0_CPU_NEG | 0.000 | – | – |
VSNS_PPVCCSA_S0_CPU_POS | 0.020 | – | – |
VSNS_PPVDDCPU_AWAKE_NEG | 0.000 | – | – |
VSNS_PPVDDCPU_AWAKE_POS | 0.030 | – | 29.000R |
VSNS_PPVIN_S0_CPUVR_VIN_NEG | 0.000 | – | – |
VSNS_PPVIN_S0_CPUVR_VIN_POS | 0.423 | – | – |
WIFI_SROM_ORG | OL | – | – |
WLAN_AUDIO_SYNC | 0.642 | – | – |
WLAN_AUDIO_SYNC_LS3V3 | 0.639 | – | – |
WLAN_HOST_WAKE | 0.489 | – | – |
WLAN_JTAG_SEL | 0.722 | – | – |
WLAN_JTAG_TCK | 0.742 | – | – |
WLAN_JTAG_TDI | 0.488 | – | – |
WLAN_JTAG_TDO | 0.740 | – | – |
WLAN_JTAG_TMS | 0.744 | – | – |
WLAN_JTAG_TRST_L | 0.739 | – | – |
WLAN_SROM_STRAP | 0.728 | – | – |
WLANBT_PCIE_WAKE_L | 0.527 | – | – |
XDP_BPM_L<0> | 0.285 | – | – |
XDP_BPM_L<1> | 0.284 | – | – |
XDP_BPM_L<2> | 0.283 | – | – |
XDP_BPM_L<3> | 0.283 | – | – |
XDP_CPU_TCK | 0.052 | – | 51.700R |
XDP_CPU_TDO | 0.218 | – | – |
XDP_JTAG_ISP_TCK | 0.569 | – | – |
XDP_JTAG_ISP_TDI | 0.567 | – | – |
XDP_JTAG_ISP_TDO | 0.570 | – | – |
XDP_PCH_OBSDATA_A0 | 0.823 | – | – |
XDP_PCH_OBSDATA_A1 | 0.823 | – | – |
XDP_PCH_OBSDATA_A2 | 0.824 | – | – |
XDP_PCH_OBSDATA_A3 | 0.824 | – | – |
XDP_PCH_OBSDATA_B0 | 0.824 | – | – |
XDP_PCH_OBSDATA_B1 | 0.824 | – | – |
XDP_PCH_OBSDATA_B2 | 0.824 | – | – |
XDP_PCH_OBSDATA_B3 | 0.824 | – | – |
XDP_PCH_OBSDATA_D0 | 0.824 | – | – |
XDP_PCH_OBSDATA_D1 | 0.824 | – | – |
XDP_PCH_OBSFN_C0 | 0.824 | – | – |
XDP_PM_RSMRST_L | 1.398 | – | – |
XDP_USB_EXTA_OC_L | 0.695 | – | – |
XDP_USB_EXTB_OC_L | 0.671 | – | – |
XDP_USB_EXTC_OC_L | 0.626 | – | – |
XDP_USB_EXTD_OC_L | 0.631 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PPBUS_G3H read on the 820-01700?
OpenBoardData's known-good values for PPBUS_G3H on the 820-01700: diode 0.415, voltage 12.600, resistance to ground 410.000. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S5 read on the 820-01700?
OpenBoardData's known-good values for PP3V3_S5 on the 820-01700: diode 0.335. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP1V8_G3S read on the 820-01700?
OpenBoardData's known-good values for PP1V8_G3S on the 820-01700: diode 0.301, voltage 1.80. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-01700 board?
Open your own 820-01700 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License