Apple laptop board · OpenBoardData

820-00281 known-good readings

Known-good readings for the Apple laptop board 820-00281: 1,482 nets, including 112 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 112 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00281.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 112 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 12

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V0_G3H0.453––
AI: what PP3V0_G3H is and how to check it

PP3V0_G3H is the always-on 3.0 V G3H rail; "G3H" means always on, from the name. The archive lists one known-good reading for this net: diode 0.453 (no condition given). Check it unpowered in diode mode to ground, then measure the voltage with power applied; the archive has no known-good voltage for this rail. A diode reading far from 0.453 usually points to a short or a damaged part on the rail, but confirm with the voltage and compare against a known-good board before replacing anything.

PP3V3_G3H0.3673.3000.003R
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H — 820-00281 reference note

  • What it is: the 3.3 V always-on rail, from the name (G3H = always on). It comes up early in the startup sequence, after PPDCIN_G3H reaches the ISL U7000 and PM_EN_P3V3_G3H is asserted, and it is measured at L6900 pin 1.
  • Known-good readings (community guide, condition as noted): diode 0.367, voltage 3.300 V, resistance 0.003R. No separate known-good resistance is listed beyond that figure.
  • How to check: with the board unpowered, diode mode from PP3V3_G3H to ground; then apply power and measure the voltage at L6900 pin 1.
  • If it's far off: a shorted or very low diode/resistance reading points to a load on the rail or a failed part on it; a correct diode reading with no voltage points back up the sequence to PPDCIN_G3H, TBA_VDDA and PM_EN_P3V3_G3H. These are likely causes, not confirmed ones — check the upstream points before replacing anything.
PP3V3_G3H_REG_R0.3493.300–
AI: what PP3V3_G3H_REG_R is and how to check it
  • PP3V3_G3H_REG_R is a 3.3 V always-on rail; the "G3H" in the name indicates it belongs to the always-on startup stage, and "REG_R" suggests a regulated branch of it (from the name, not from board data).
  • Known-good readings for this board: diode 0.349 to ground, voltage 3.300 V. These are community figures and a guide only.
  • To check it: power off and measure diode mode from the rail to ground, then power up and measure the voltage.
  • A voltage well below 3.300 V points to a load pulling the rail down or a supply problem upstream; a diode reading far from 0.349 suggests a short or open on that net. No known-good resistance reading is available here, so compare against a matching rail or a known-good board before condemning a part.
PPBUS_G3H0.45013.1000.115R
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H — the G3H suffix means "always on" (from the name): the main bus rail that should be present once the charger and ISL U7000 bring the board up, before the S5/S0 rails.

  • Known-good readings (community guide, board state not stated): diode 0.450, voltage 13.100, resistance 0.115R.
  • Check with the board unpowered in diode mode from PPBUS_G3H to ground, then apply power and measure the voltage on the rail.
  • A far-off diode or resistance reading usually points to a short or a leaky load on the bus; a wrong voltage with a good diode reading points back at the charging/ISL side, which the notes say should open Q7030 and Q7040 and generate PPBUS_G3H last.
  • No known-good current-limited or loaded reading is recorded here, so compare against a matching rail on a known-good board if in doubt.
PPBUS_G3H_R0.428––
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main system bus rail produced by U7000 once the ISL has its inputs and the G3H stage is up; the "G3H" part of the name indicates it is an always-on rail, and "_R" is just the net's suffix here. The only known-good figure in the archive is a diode reading of 0.428 to ground; there is no known-good voltage or resistance value for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the DC voltage on it. A diode reading far from 0.428 usually points to a short or a leaky component on the rail rather than the rail itself, so compare against a matching net or a known-good board before condemning anything. The 0.428 is a community guide and varies with board state, so treat a small difference as normal.

PPDCIN_G3H0.17020.000156.000R
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main DC input rail after the USB-C front end, and the G3H suffix (from the name) means it is always-on whenever input power is present. Known-good readings here are a diode value of 0.170 to ground, about 20.000 V with power applied, and 156.000R resistance; the notes also show 5 V early in the CD3215 sequence and 20 V after the PD switchover, checked at CC773 pin 1 and at Q3100, Q3200, QB300 and QB400 pin 8. Check it unpowered in diode mode to ground first, then measure the voltage with a charger connected. A diode reading far from 0.170 usually points to a short or leaky part on the rail, while missing voltage with good diode readings points back to the CD3215 front end or the input MOSFETs. No known-good value is listed for a current measurement on this rail.

PPDCIN_G3H_CHGR0.53920.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H part of the name indicates it is an always-on startup rail (from the name). Known-good readings in the archive are diode 0.539 and 20.000 V, with no condition recorded. Check it unpowered in diode mode to ground, then with a charger applied measure the voltage. A diode reading far from 0.539 suggests a short or leaky part on the rail; a voltage far from 20 V points to the USB-C input, the CD3215 unit or the input MOSFETs not passing power through. No known-good resistance reading is recorded here.

PPDCIN_G3H_CHGR_R0.538––
AI: what PPDCIN_G3H_CHGR_R is and how to check it

PPDCIN_G3H_CHGR_R is a G3H (always-on) input rail feeding the charger section; the "_CHGR_R" suffix suggests the charger-side branch of PPDCIN_G3H, from the name only.

  • Known-good: diode mode to ground 0.538 (board unpowered). No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power up and measure DC volts on it.
  • A diode reading far below 0.538 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PPVBAT_G3H_CHGR_R0.45013.1000.115R
AI: what PPVBAT_G3H_CHGR_R is and how to check it

Reference note for PPVBAT_G3H_CHGR_R on the 820-00281:

  • From the name, this is a G3H (always-on) battery/charger rail: the battery-side feed into the charging circuit, present whenever the charger is connected.
  • Known-good readings in the archive: diode 0.450, voltage 13.100, resistance 0.115R. These are community values and vary with board state, so treat them as a guide.
  • Check it unpowered in diode mode to ground first, then measure the voltage with power applied.
  • A reading far from these usually points to a short or leak on the rail, or a fault in the charger/battery path feeding it. No known-good value of another kind is listed here.
PPVBAT_G3H_CHGR_REG0.45013.1000.115R
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a battery-side rail in the always-on G3H group, judging by its name: the charger's regulated battery feed. The archive lists diode 0.450, voltage 13.100 and resistance 0.115R, with no stated condition, so treat them as a guide only. With the board unpowered and the battery disconnected, measure diode mode to ground; then apply power and check the voltage. A diode or resistance far below the listed values suggests a short or heavy load on the rail, while a missing voltage points upstream to the charger circuit. No known-good waveform or current reading is recorded here.

PPVBAT_G3H_CONN0.639––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H supply, judging by its name (G3H = always on). The only known-good figure here is a diode reading of 0.639 to ground, with no condition noted; there's no known-good voltage or resistance for this net.

  • Check it unpowered: meter in diode mode, black probe on ground, red on the net, and compare with 0.639. A far lower reading suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken connection.
  • Then apply power and measure the voltage, but no known-good voltage is recorded here, so compare against a matching battery-side net or a known-good board.
  • A single off reading isn't proof of a bad part; confirm with a second measurement before replacing anything.
PPVIN_G3H_P3V3G3H0.545––
AI: what PPVIN_G3H_P3V3G3H is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V3G3H is the input feed for the always-on 3V3 G3H rail (G3H = always on). It is upstream of PP3V3_G3H, which the notes show at 3V3 on L6900 pin 1.
  • Known-good reading: diode 0.545 to ground. No known-good voltage reading for this net here.
  • How to check: power off, diode mode, black probe to ground, red on the net; then power up and measure the voltage. Compare with PP3V3_G3H at L6900 pin 1.
  • If far off: a low diode reading usually points to a shorted load on the rail; a high or open one to a broken feed. That is a guide, not a confirmed cause.

S5 and SUS: standby 19

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_S5_PCH_DCPDSW0.328––
AI: what PP1V_S5_PCH_DCPDSW is and how to check it
  • What it is: From the name, PP1V_S5_PCH_DCPDSW is a 1 V rail in the S5 standby domain feeding the PCH's DCPD switch. The S5/SUS naming puts it at the standby stage, so it should be present before the board fully powers on.
  • Known-good reading: Diode mode to ground is 0.328. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.328 suggests a short or leaky load on the rail; a much higher or open reading suggests a broken trace or missing part. Confirm with a second measurement before replacing anything.
PP1V_SUS_PCH_VCCCLK5_F0.0561.00055.300R
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it

PP1V_SUS_PCH_VCCCLK5_F — from the name, a 1 V standby (SUS/S5) rail feeding the PCH's clock-related supply. The "F" suffix suggests a filtered or derived version of the rail.

  • Known-good readings here: diode 0.056, voltage 1.000 V, resistance 55.300R. These come from community contributions, so treat them as a guide, not a spec.
  • To check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • A diode or resistance far below the known-good value usually points to a short or a leaky load on the rail; a voltage far off 1.000 V points to the rail not coming up or being loaded down.
  • No known-good current-draw or ripple reading here, so compare against a matching rail or a known-good board if you need one.
PP1V_SUS_PCH_VCCHDAPLL_F0.0561.00055.300R
AI: what PP1V_SUS_PCH_VCCHDAPLL_F is and how to check it
  • What it is: From its name, PP1V_SUS_PCH_VCCHDAPLL_F is a 1 V rail feeding the PCH's HDAPLL supply, in the S5/SUS standby stage. The name suggests it should be present in standby, before the board fully powers on.
  • Known-good readings (community, a guide only): diode 0.056, voltage 1.000 V, resistance 55.300R. No known-good value is recorded for other conditions.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail. Compare both with the readings above.
  • If far off: A diode reading much lower than 0.056 suggests a short or leaky load on the rail; a correct diode but missing 1 V points upstream to the rail's supply or enable. These are likely causes, not confirmed ones — check the supply and enable before replacing anything.
PP1V_SUS_PCH_VCCUSB2HDAPLL_F0.0561.00055.300R
AI: what PP1V_SUS_PCH_VCCUSB2HDAPLL_F is and how to check it

PP1V_SUS_PCH_VCCUSB2HDAPLL_F is a 1 V standby (SUS/S5) rail feeding the PCH's USB2 HDAPLL supply, judging from the name. Known-good from the archive: diode 0.056, voltage 1.000 V, resistance 55.300R (no condition recorded). Check it unpowered in diode mode to ground, then measure the voltage with power applied. A diode or resistance far below known-good suggests a short or leaky load on the rail; far above suggests an open feed or missing enable. No known-good reading exists for other conditions here, so compare against a matching rail or a known-good board.

PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.056–55.300R
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL_F is and how to check it

PP1V_SUSSW_PCH_VCCAMPHYPLL_F — from the name, a 1V rail in the S5/SUS standby stage, feeding the PCH's VCCAMPHYPLL (the PCH's clock/analog PLL supply). It's a standby rail, so it can be present before the board fully powers on.

  • Known-good readings here: diode 0.056 and resistance 55.300R. No known-good voltage is recorded for this rail.
  • Check with the board unpowered: diode mode, red probe on the rail, black to ground, and compare with 0.056. Then power up and measure the voltage; there's no known-good voltage figure to compare against, so use a matching rail or a known-good board.
  • A diode reading far below 0.056 usually points to a short or a leaky part on the rail; a much higher one can mean an open path. One reading alone doesn't confirm a bad part — recheck and compare before replacing anything.
PP1V0_SUS0.0561.00055.300R
AI: what PP1V0_SUS is and how to check it

PP1V0_SUS — a 1.0 V standby rail; the "SUS" and S5 standby stage come from the rail name, not from a schematic here.

  • Known-good readings in the archive: diode 0.056, voltage 1.000 V, resistance 55.300R. These are community figures and only a guide; the data gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage.
  • A diode far below 0.056 suggests a short or a heavy load on the rail; a voltage well off 1.000 V points to the rail not coming up or being dragged down. Confirm with a second reading before suspecting a part.
PP1V2_S5_SMC_VDDC0.4991.2000.018R
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC — from the name, a 1.2 V SMC supply in the S5 (standby) domain, so it should be present in standby before the board fully powers on.

  • Known-good readings here: diode 0.499, voltage 1.200 V, resistance 0.018R. These are community values and only a guide.
  • Check it at C5012 pin 1: diode mode to ground with the board unpowered, then the voltage with power applied. The archive gives no condition for the readings.
  • A voltage far from 1.200 V, or a diode reading well off 0.499, usually points to the rail being loaded, shorted or not being enabled — not proof of a bad part on its own. No known-good current draw is listed here.
PP1V8_SUS0.4411.800–
AI: what PP1V8_SUS is and how to check it

PP1V8_SUS is a 1.8 V standby rail; the "SUS" and "S5" in its name indicate it belongs to the always-on standby domain, not a switched main rail (this is from the name, not the board data).

  • Known-good readings here: diode 0.441 and voltage 1.800. These are community readings and only a guide.
  • Check it with the board unpowered: diode mode, black probe to ground, red probe on the rail, and compare with 0.441.
  • Then power the board and measure the voltage; it should sit at 1.800 V.
  • A voltage far off 1.8 V, or a diode reading well below 0.441, usually points to a short or a load pulling the rail down. A high or open diode reading points more to a missing feed or an open connection. No known-good resistance reading exists for this rail.
PP1V8_SUS_REG_R0.4351.800–
AI: what PP1V8_SUS_REG_R is and how to check it

Reference note for PP1V8_SUS_REG_R on the 820-00281:

  • What it is: a 1.8 V standby rail. The "1V8" is the level, and "SUS" (from the name) places it in the standby/S5 stage, so it should be present before the board fully powers on. "REG" suggests a regulated output from a local regulator.
  • Known-good readings (community archive, a guide only): diode 0.435 to ground, voltage 1.800.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.435. Then apply power in the standby state and measure the voltage, expecting 1.800.
  • If far off: a much lower diode reading points to a short or leaky part on the rail; a correct diode reading with missing or low voltage points to the regulator or its enable/supply. There is no known-good resistance reading here, so compare against a matching rail or a known-good board.
PP3V0_S5_AVREF_SMC0.5783.0000.311R
AI: what PP3V0_S5_AVREF_SMC is and how to check it

PP3V0_S5_AVREF_SMC is a 3.0 V S5 (standby) rail feeding the SMC's analog reference, judging from the name. Known-good readings here are diode 0.578, voltage 3.000 V and resistance 0.311R; the community sequence also lists 3V0 on this rail at C5020 pin 1. Check it unpowered in diode mode to ground, then power the board and measure the voltage at C5020 pin 1. A voltage well off 3.0 V, or a diode reading far from 0.578, usually points to a short or a missing supply on that rail rather than the SMC itself. No separate known-good resistance condition is recorded beyond the 0.311R figure.

PP3V3_S50.3903.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the S5/SUS part of the name places it in the standby stage (from the name, not a schematic). Known-good readings for this board: diode 0.390 and voltage 3.300, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.390 suggests a short or leaky load on the rail; a correct diode reading with missing 3.3 V points upstream at the standby supply enabling it. No known-good resistance reading is available here.

PP3V3_S5_POLARIS0.379––
AI: what PP3V3_S5_POLARIS is and how to check it

PP3V3_S5_POLARIS is a 3.3 V rail in the S5 (standby) startup stage, judged from the name; the archive doesn't say which parts sit on it. The only known-good reading here is a diode value of 0.379 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. No known-good voltage reading is listed for this rail, so compare against a matching 3.3 V S5 rail or a known-good board. A diode reading far from 0.379 usually points to a short or a damaged part on the rail, but confirm with a second measurement before replacing anything.

PP3V3_S5_SMC_VDDA0.349––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V SMC supply that sits in the S5 standby stage, judging by its name; the archive doesn't list which parts it feeds. Its only known-good reading is a diode value of 0.349 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, which should be about 3.3 V. No known-good voltage reading exists here, so compare against a matching SMC rail on a known-good board. A diode reading far below 0.349 suggests a short or leaky part on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S5_T1390.383––
AI: what PP3V3_S5_T139 is and how to check it

PP3V3_S5_T139 is a 3.3 V standby rail, judged from its name: S5/SUS means it comes up in standby, before the main rails. The only known-good figure here is a diode reading of 0.383 to ground; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.383 usually points to a short or a damaged part on that net, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S5_TBT_T_SW0.478––
AI: what PP3V3_S5_TBT_T_SW is and how to check it
  • What it is: From the name, a 3.3 V rail in the S5/SUS standby stage, likely a switched (SW) Thunderbolt-related supply. The exact parts on it aren't known here.
  • Known-good reading: diode 0.478 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power applied, measure the voltage on the rail.
  • If it's far off: a low diode reading or a missing/short voltage usually points to a short or a part on that rail, but that's a likely cause, not confirmed. Compare with a matching rail on the other side of the pair before replacing anything.
PP3V3_S5_TBT_X_SW0.464––
AI: what PP3V3_S5_TBT_X_SW is and how to check it
  • What it is: From the name, a 3.3 V switched rail in the S5 standby stage, tied to the TBT (Thunderbolt) side. The exact parts on it aren't listed in this board's data.
  • Known-good: diode 0.464 to ground, no condition recorded. No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a low diode reading suggests a short on the rail; a missing voltage with a normal diode reading points to the rail's enable or source. Confirm with a second measurement before replacing anything.
PP3V3_SUS0.365––
AI: what PP3V3_SUS is and how to check it
  • What it is: PP3V3_SUS is a 3.3 V standby rail; the "SUS" in the name indicates the standby/suspend domain, so it should be present in standby before the board fully powers on.
  • Known-good reading: diode 0.365 to ground, from the readings archive. No known-good voltage reading is listed here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_SUS to ground and compare with 0.365. Then apply power and measure the voltage on the rail — it should sit near 3.3 V in standby.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a correct diode reading with no voltage points upstream, at the standby supply or its enable. These are general guidelines, not confirmed causes for this board.
PP5V_S50.473––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage. The only known-good figure here is a diode reading of 0.473 to ground; no known-good voltage reading is listed for this rail.

  • With the board unpowered, measure diode mode from PP5V_S5 to ground and compare with 0.473.
  • Then apply power and check the voltage at the rail; expect about 5 V, though that is general expectation, not a recorded value for this board.
  • A diode reading far below 0.473 suggests a short or a leaky load on the rail; a much higher or open reading points to a broken path feeding it. Treat one reading as a guide only and confirm before replacing anything.
PPVIN_SUS_VR5_R0.449––
AI: what PPVIN_SUS_VR5_R is and how to check it
  • What it is: From the name, a standby (S5/SUS) input rail feeding a VR5 regulator. The data doesn't say which parts sit on it.
  • Known-good reading: diode 0.449 to ground, from the readings archive; treat it as a guide, not a spec.
  • How to check: power off and unplugged, diode mode from PPVIN_SUS_VR5_R to ground; then power up and measure its voltage. No known-good voltage is listed here.
  • If it's far off: a much lower diode reading usually points to a shorted load on the rail; a much higher one to an open feed or bad joint. Confirm with a second measurement before replacing anything.

S4 18

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V8_S40.426––
AI: what PP1V8_S4 is and how to check it
  • What it is: PP1V8_S4 is a 1.8 V rail in the S4 startup stage; the "1V8" and "S4" parts come from the name, not from circuit data.
  • Known-good reading: diode 0.426 to ground (community value, a guide only; board state varies). No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from PP1V8_S4 to ground; then power the board and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail; a missing voltage with a normal diode reading points to the rail's supply or enable. Neither is confirmed from one reading.
PP3V3_S40.328––
AI: what PP3V3_S4 is and how to check it
  • What it is: PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging by its name (general naming, not from this board's data). Which parts sit on it isn't known here.
  • Known-good reading: diode 0.328 to ground, from the readings archive; no condition is recorded, so treat it as a guide.
  • How to check: power off and unplug, then diode mode from PP3V3_S4 to ground. Then power up and measure the voltage, which should be about 3.3 V once the board reaches S4.
  • If it's far off: a low diode reading or a collapsed voltage usually points to a short or a heavy load on the rail. There's no known-good voltage reading for this rail here, so compare with a matching rail on a known-good board.
PP3V3_S4_BT0.328––
AI: what PP3V3_S4_BT is and how to check it
  • What it is: PP3V3_S4_BT is a 3.3 V rail that comes up at the S4 stage of the power sequence, judging by its name (general naming convention, not from this board's data). The "_BT" suffix usually marks a rail feeding Bluetooth circuitry, again from the name only.
  • Known-good reading: diode mode to ground is 0.328, from the community readings archive. No known-good voltage reading is listed here for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the DC voltage, comparing against a matching rail or a known-good board since no voltage figure is recorded.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; an open or high reading suggests a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_S4_MESA_SW0.424––
AI: what PP3V3_S4_MESA_SW is and how to check it
  • What it is: PP3V3_S4_MESA_SW is a 3.3 V switched rail. The "S4" in the name puts it in the S4 startup stage, and "MESA_SW" suggests a switched supply for the MESA section — that's from the name only, not from board data.
  • Known-good reading: the archive lists diode 0.424 for this net. No known-good voltage is recorded here.
  • How to check: with the board unpowered, measure diode mode from the net to ground; then power up and measure the voltage at the same point.
  • If it's far off: a diode reading well below 0.424 suggests a short or leaky load on the rail; a missing 3.3 V with a normal diode reading points more to the switch or its enable. These are general guidelines, not confirmed causes.
PP3V3_S4_SOC_PMU0.330––
AI: what PP3V3_S4_SOC_PMU is and how to check it
  • What it is: From the name, a 3.3 V rail feeding the SOC/PMU section in the S4 startup stage. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.330 to ground (community value, a guide; no condition given). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage, expecting about 3.3 V from the name.
  • If it's far off: a low diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream, to the S4 enable or the regulator feeding it. No known-good voltage here, so compare against a matching rail or a known-good board.
PP3V3_S4_T1510.424––
AI: what PP3V3_S4_T151 is and how to check it
  • What it is: PP3V3_S4_T151 is a 3.3 V rail in the S4 startup stage, judged from its name; the "T151" suffix isn't explained by the available data.
  • Known-good reading: diode mode to ground 0.424, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail, but one reading isn't proof. Compare against a known-good board or a matching rail before replacing anything.
PP3V3_S4_TPAD0.320––
AI: what PP3V3_S4_TPAD is and how to check it
  • What it is: PP3V3_S4_TPAD is a 3.3 V rail for the trackpad, from its name; the S4 in the name puts it in the S4 startup stage (general naming, not from this board's data).
  • Known-good: diode 0.320 to ground. No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power applied, measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to the S4 enable or supply. Which parts sit on this net isn't known here, so trace from the rail.
PP3V3_S4_WLAN0.328––
AI: what PP3V3_S4_WLAN is and how to check it
  • What it is: PP3V3_S4_WLAN is a 3.3 V rail for the WLAN section, enabled at the S4 stage — both from the name, not from board data.
  • Known-good reading: diode 0.328 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.328; then power on and measure the voltage, expecting about 3.3 V once the board reaches S4.
  • If it's far off: a much lower diode reading suggests a short on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. These are general possibilities, not confirmed causes.
PP3V3_S4_WLAN_SW0.351––
AI: what PP3V3_S4_WLAN_SW is and how to check it
  • What it is: PP3V3_S4_WLAN_SW is a 3.3 V WLAN supply switched on at the S4 stage, judging by its name. The board data doesn't say which parts sit on it.
  • Known-good reading: diode 0.351 to ground, from the community archive; treat it as a guide, since readings vary with board state. There's no known-good voltage reading for this rail here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.351. Then power up and measure the voltage; it should sit near 3.3 V once the board reaches S4.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail, and no voltage at S4 points to the switch or its enable. No known-good resistance reading here, so compare against a matching rail or a known-good board.
PP3V3_S4SW_SNS0.569––
AI: what PP3V3_S4SW_SNS is and how to check it
  • What it is: PP3V3_S4SW_SNS is a 3.3 V rail that switches on at the S4 stage of startup, judging by the name. The "_SNS" suffix usually means a sense line for that rail (general naming, not from this board's data).
  • Known-good reading: diode mode to ground 0.569, from the community archive. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground and compare with 0.569. Then power up and measure the voltage; it should come up around 3.3 V once the board reaches S4.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail; a correct diode reading with no voltage points more to the rail not being enabled or its source not coming up. Treat the 0.569 as a guide only, since readings vary with board state.
PP3V3_S4SW_SNS_FET_R0.542––
AI: what PP3V3_S4SW_SNS_FET_R is and how to check it
  • What it is: From the name, a 3.3 V rail switched at the S4 stage (S4 = suspend-to-RAM stage in the power sequence), with a FET sense/feedback node. The exact parts on this net aren't known here.
  • Known-good: diode mode to ground 0.542 (no condition given). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the net to ground and compare with 0.542; then power on and measure the voltage, expecting about 3.3 V from the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream, to the switch or enable for S4. Treat this as a likely cause, not confirmed.
PP5V_S40.4255.000–
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging from its name (general naming, not from this board's data). The archive lists a known-good diode reading of 0.425 and a known-good voltage of 5.000; no condition is recorded for either, so treat them as a guide. With the board unpowered, measure diode mode from PP5V_S4 to ground and compare with 0.425; then power up and measure the rail voltage against 5.000. A diode reading far below 0.425 suggests a short or a failing load on the rail, while a correct diode reading with missing voltage points upstream to the rail's enable or source. No known-good resistance reading exists here, so a shorted rail would need to be traced by lifting or comparing loads.

PP5V_S4_ISNS_DOL––
AI: what PP5V_S4_ISNS_D is and how to check it
  • What it is: From the name, a 5 V current-sense (ISNS) rail in the S4 startup stage. The data doesn't say which parts sit on it.
  • Known-good readings: The only one recorded is diode mode OL to ground. There's no known-good voltage or resistance here.
  • How to check: With the board unpowered, diode mode from the rail to ground and compare with the recorded OL; then power up and measure the voltage on the rail.
  • If it's far off: A low diode reading or a missing 5 V usually points to a short or a rail that isn't being enabled, but that's a likely cause, not a confirmed one.
PP5V_S4_T_USBC0.2115.000–
AI: what PP5V_S4_T_USBC is and how to check it

Reference note for PP5V_S4_T_USBC on the 820-00281:

  • The name marks it as a 5 V rail in the S4 startup stage, tied to the USB-C side (from the name). The board data doesn't list which parts sit on it.
  • Known-good readings from the archive: diode 0.211 and voltage 5.000. These are community values and only a guide; the data gives no condition for them.
  • To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage.
  • A diode reading far below 0.211 suggests a short or a leaky load on the rail; a voltage well under 5.000 with power applied points to the rail not being enabled or being pulled down. No known-good resistance reading exists here, so compare with a matching net or a known-good board.
PP5V_S4_TPAD_CONN0.421––
AI: what PP5V_S4_TPAD_CONN is and how to check it
  • What it is: PP5V_S4_TPAD_CONN is a 5 V rail feeding the trackpad connector, enabled at the S4 stage of power-up (both from the name).
  • Known-good reading: diode 0.421 to ground, from the readings archive. No known-good voltage reading for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.421; then power up and check for 5 V at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a missing 5 V with a good diode reading points to the rail not being enabled. These are general guidelines, not confirmed causes.
PP5V_S4_X_USBC0.1645.000–
AI: what PP5V_S4_X_USBC is and how to check it
  • What it is: PP5V_S4_X_USBC is a 5 V rail that, from its name, belongs to the S4 startup stage and the USB-C side of the board. The archive doesn't say which parts sit on it.
  • Known-good readings (community, guide only): diode 0.164 and voltage 5.000. No other condition is recorded.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then power up and measure the voltage on the same point.
  • If it's off: a diode reading far from 0.164 usually points to a short or a leaky part on that rail; a correct diode reading with no 5 V points upstream, toward whatever should be switching the rail on. No known-good resistance reading exists here, so compare against a matching net or a known-good board.
PPBUS_S4_HS_TPAD0.45012.600–
AI: what PPBUS_S4_HS_TPAD is and how to check it

PPBUS_S4_HS_TPAD is a PPBUS-derived rail for the trackpad, active in the S4 stage, judging from its name. Known-good readings here are diode 0.450 and voltage 12.600; the data gives no condition for these, so treat them as a guide only.

  • Check it with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.450.
  • Then power the board and measure the voltage, comparing with 12.600.
  • A diode reading far below 0.450 suggests a short or leaky part on that rail; a far higher or open reading suggests a broken connection.
  • A missing or low voltage with a normal diode reading points upstream, toward the PPBUS source or the S4 enable, rather than the rail itself.

No known-good resistance reading exists for this rail.

PPVIN_S4_TPAD_FUSE0.45012.600–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it
  • What it is: A fused input rail for the S4 stage of the trackpad supply, judged from the name (S4 = a later startup stage, after the G3H rails). The archive doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.450 to ground, and 12.600 V with power applied. No condition is recorded with these.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power up and measure the voltage on it.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; no or low voltage with a normal diode reading points back to the fuse or whatever feeds it. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before replacing anything.

S3: memory 10

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.690––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it
  • What it is: PP0V6_S3_MEM_VREFCA_A is a 0.6 V memory reference rail, judged from its name (0V6 = 0.6 V, S3 = memory stage). The parts on it aren't known from the archive.
  • Known-good reading: diode 0.690 to ground, from the community archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage.
  • If it's far off: a low diode reading suggests a short or leaky part on the rail; a correct diode but wrong voltage points upstream at the rail's source. Treat this as a guide only, since readings vary with board state.
PP0V6_S3_MEM_VREFDQ_A0.751––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a memory reference rail: the 0V6 in the name suggests about 0.6 V, S3 marks it as a memory-rail stage, and VREFDQ is the DDR data-reference voltage (that part is general naming, not from board data). The only known-good reading here is a diode value of 0.751 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied and compare against a matching reference net or a known-good board. A diode reading far below 0.751 usually points to a short or leaky part on the rail, while a far higher or open reading points to a broken connection; treat the 0.751 as a guide only, since community readings vary with board state.

PP0V6_S3_MEM_VREFDQ_B0.746––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it
  • What it is: PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail, judged from its name (0V6, S3 memory stage). The archive doesn't say which parts sit on it.
  • Known-good reading: diode 0.746 to ground, from the community archive; treat it as a guide, since readings vary with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.746. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. A missing voltage with a normal diode reading points more to the rail's source or its enable.
PP1V0_S30.213––
AI: what PP1V0_S3 is and how to check it
  • PP1V0_S3 is a 1.0 V rail; the "S3" suffix puts it in the memory (S3) startup stage, from the name. General convention: S3 rails come up after the always-on rails and before/with DRAM use.
  • Known-good: diode mode to ground 0.213 (no condition recorded). No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point.
  • A diode reading far from 0.213 suggests a short or a damaged load on the rail; a missing voltage with a normal diode reading points upstream to the rail's enable or source. Compare against a matching rail on a known-good board where possible.
PP1V2_S30.2251.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail; the S3 suffix suggests it belongs to the memory stage of the power sequence, based on the name. Known-good readings for this board are diode 0.225 and 1.200 V. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.225 suggests a short or a leaky part on the rail; a voltage well off 1.200 V points to the rail not coming up or being loaded down. No known-good resistance reading is listed here, so compare against a matching rail or a known-good board.

PP1V2_S3_CPUDDR0.221––
AI: what PP1V2_S3_CPUDDR is and how to check it
  • What it is: PP1V2_S3_CPUDDR is a 1.2 V memory rail that comes up at the S3 stage, judging from the name (S3 = memory stage). The board data has no part list, so which components sit on it isn't known.
  • Known-good reading: diode 0.221 to ground, from the community archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a diode reading well below 0.221 suggests a short or a leaky part on the rail; a missing or wrong voltage points to the rail's supply or enable. Treat 0.221 as a guide only, since readings vary with board state, and confirm before replacing anything.
PP1V2_S3_REG_R0.2251.200–
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R is a 1.2 V regulator rail in the S3 (memory) startup stage, judged from the rail name. Known-good readings for this board: diode 0.225 and voltage 1.200, with no condition recorded, so treat them as a guide.

  • Check it unpowered in diode mode from the rail to ground; compare with 0.225.
  • Then power the board and measure the voltage; expect about 1.200 V.
  • A far-off diode reading usually points to a short or a damaged part on the rail; a wrong voltage with a normal diode reading points more to the regulator or its enable.

No known-good resistance reading exists for this rail.

PP1V8_S30.352–0.900R
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is the 1.8 V rail for the S3 (memory) startup stage, judging by its name. The archive lists a known-good diode reading of 0.352 and a resistance of 0.900R; no known-good powered voltage is recorded here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.352, then apply power and check the voltage. A diode reading far below 0.352 suggests a short or leaky load on the rail; a much higher one suggests an open path. These are community readings and only a guide, so confirm on a matching rail or known-good board before replacing anything.

PP1V8_S3_MEM0.352–0.900R
AI: what PP1V8_S3_MEM is and how to check it
  • What it is: PP1V8_S3_MEM is a 1.8 V memory rail in the S3 (suspend-to-RAM) startup stage, judged from the rail's name. The exact parts it feeds aren't listed in the available data.
  • Known-good readings: diode 0.352 and resistance 0.900R, with no condition stated. These are community figures and only a guide.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then apply power and measure the voltage.
  • If it's far off: a low diode or resistance reading usually points to a short or a leaky load on the rail; a missing voltage points upstream to the rail's enable or supply. No known-good voltage reading is available here, so compare against a matching rail or a known-good board before condemning anything.
PP3V3_S3_DPMUX_UC_R0.329––
AI: what PP3V3_S3_DPMUX_UC_R is and how to check it

PP3V3_S3_DPMUX_UC_R is a 3.3 V rail in the S3 (memory) startup stage, judged from its name; it likely feeds the USB-C display-port mux logic, but that's general reasoning, not from this board's data. The only known-good figure here is a diode reading of 0.329 to ground, with no condition recorded and no known-good voltage value. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.329 suggests a short or leaky load on the rail; a missing voltage with a normal diode reading points upstream to the rail's enable or source. These readings are community guides and vary with board state, so confirm against a matching rail before condemning anything.

S0: running 53

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.136––
AI: what PP0V6_S0_DDRVTT is and how to check it
  • What it is: PP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the "S0" in the name indicates it is active in the running (S0) state. This is from the rail name only.
  • Known-good reading: diode 0.136 to ground in diode mode, board unpowered. No known-good voltage reading here.
  • How to check: with power off, measure diode mode from the rail to ground and compare with 0.136; then power up and measure the voltage, which should sit near 0.6 V by the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. These are likely causes, not confirmed ones.
PP1V0_S0SW0.214––
AI: what PP1V0_S0SW is and how to check it
  • What it is: PP1V0_S0SW is a 1.0 V rail; the "S0" in its name marks it as a running-state rail, and "SW" usually means it is switched (general naming, not from this board's data).
  • Known-good reading: diode 0.214 to ground, from the readings archive. No known-good voltage is listed here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail, while a missing voltage with a normal diode reading points upstream to the switch or its enable. Confirm with a second measurement before replacing anything.
PP1V2_S0SW0.219––
AI: what PP1V2_S0SW is and how to check it

Reference note for PP1V2_S0SW on the 820-00281:

  • From the name, this is a 1.2 V rail in the S0 (running) power state; the S0 part comes from the rail name, not from measured data.
  • Known-good reading here is diode mode 0.219 to ground. No known-good voltage reading is recorded for this rail.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.219 suggests a short or a damaged component on the rail; a correct diode reading with wrong voltage points more to the rail's supply or enable. Treat both as a guide, not a confirmed fault.
PP1V5R1V35_S0_GPU_IC0.231––
AI: what PP1V5R1V35_S0_GPU_IC is and how to check it
  • What it is: From the name, a 1.5 V/1.35 V GPU core rail that comes up in the S0 (running) state. The board data doesn't say which parts sit on it.
  • Known-good reading: diode 0.231 (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: power off, diode mode from the rail to ground, then power on and measure the voltage at the same point.
  • If it's far off: a low or shorted diode reading suggests a short on the rail; a correct diode reading with no voltage points to the rail not being enabled or its supply missing. Confirm with a second measurement before replacing anything.
PP1V5R1V35_S0_GPU_MEM0.0531.500170.000
AI: what PP1V5R1V35_S0_GPU_MEM is and how to check it

PP1V5R1V35_S0_GPU_MEM is a 1.5 V GPU memory rail; the "S0" in its name indicates it belongs to the running (S0) state, and the "1V5"/"1V35" suggest the two voltages it can take. Known-good readings for this board: diode 0.053, voltage 1.500, resistance 170.000 — community figures, so treat them as a guide. Check it unpowered in diode mode to ground, then power the board and measure the voltage; the resistance figure is also a power-off check. A reading far from these usually points to a short or a rail that isn't coming up, but one reading alone doesn't condemn a part — confirm with a second measurement before replacing anything.

PP1V8_S00.3501.800–
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail; the S0 suffix means it belongs to the running (S0) state, from the name. Known-good readings here: diode 0.350 and voltage 1.800. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A far-off diode reading usually points to a short or a damaged part on the rail; a missing or wrong voltage points to the rail not being enabled or its source failing. No known-good resistance reading is listed for this rail.

PP1V8_S0_GPU0.188––
AI: what PP1V8_S0_GPU is and how to check it
  • What it is: PP1V8_S0_GPU is a 1.8 V GPU rail, from the name; the S0 suffix means it belongs to the running state, so it should only come up once the board is fully on.
  • Known-good reading: diode 0.188 to ground, from the readings archive. No known-good voltage reading for this rail here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.188; then power up and measure the voltage, expecting about 1.8 V once the board is in S0.
  • If it's far off: a diode reading well below 0.188 suggests a short or a failing load on the rail; a correct diode reading with no voltage points upstream, at the rail's enable or supply. Treat these as guides, not confirmed faults.
PP1V8_S0_GPU_LC_IC0.188––
AI: what PP1V8_S0_GPU_LC_IC is and how to check it
  • What it is: PP1V8_S0_GPU_LC_IC is a 1.8 V rail feeding the GPU's low-current (LC) supply, judging from the name; the S0 suffix means it belongs to the running state, so it should only be present once the board is fully on.
  • Known-good reading: diode mode to ground is 0.188 in the archive. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up into S0 and measure the voltage at the same point.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream to its enable or source supply. The archive doesn't list which parts sit on this net, so trace it on the board.
PP1V8_S0_LDO_AUD0.480––
AI: what PP1V8_S0_LDO_AUD is and how to check it
  • What it is: PP1V8_S0_LDO_AUD is a 1.8 V low-dropout audio rail. The "S0" in the name marks it as a running-state rail, and "LDO_AUD" as an audio LDO; that reading is from the name, not from circuit data.
  • Known-good reading: diode mode to ground 0.480. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure its voltage.
  • If it's far off: a low diode reading or a collapsed voltage usually points to a short or a heavy load on the rail, but one reading doesn't confirm a bad part. Compare with a matching audio rail on a known-good board before replacing anything.
PP1V8_S0_PCH_VCCHDA_F0.3501.800–
AI: what PP1V8_S0_PCH_VCCHDA_F is and how to check it

PP1V8_S0_PCH_VCCHDA_F is a 1.8 V rail feeding the PCH's HDA (audio) supply; the "S0" in the name indicates it belongs to the running (S0) state, and the "1V8" gives its nominal level.

  • Known-good from the archive: diode 0.350 to ground, voltage 1.800.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail.
  • Then power up and measure the voltage; it should sit at 1.800 V.

A diode reading well below 0.350 suggests a short or leaky load on the rail; a missing or low voltage with a normal diode reading points upstream, to the rail's enable or source. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.

PP1V8_S0SW_DFR0.5521.800–
AI: what PP1V8_S0SW_DFR is and how to check it
  • What it is: PP1V8_S0SW_DFR is a 1.8 V rail; the "S0" in the name marks it as a running-state (S0) supply, and "SW" suggests a switched rail (general naming convention, not from this board's data).
  • Known-good readings (community guide): diode 0.552 and voltage 1.800.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a low diode reading points to a short or heavy load on the rail, a high one to an open path; a wrong voltage under power points to the rail's source or its enable. No known-good resistance reading is listed here, so compare against a matching rail or a known-good board before replacing anything.
PP3V3_S00.326––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that comes up at the S0 (running) stage, judging from its name. The only known-good figure here is a diode reading of 0.326 to ground; there is no known-good voltage value for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.326 usually points to a short or a leaky load on the rail, but one reading isn't proof, so compare with a matching point before condemning anything.

PP3V3_S0_AUD_F0.345––
AI: what PP3V3_S0_AUD_F is and how to check it
  • What it is: From the name, a 3.3 V rail in the S0 (running) state, feeding the audio section. It is only expected up once the board is fully on.
  • Known-good reading: diode mode to ground is 0.345. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage, ideally with the board in S0.
  • If it's far off: a low diode reading suggests a short or a failing load on the rail; an open reading suggests a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_S0_CARBON_R–3.300–
AI: what PP3V3_S0_CARBON_R is and how to check it
  • What it is: From the name, PP3V3_S0_CARBON_R is a 3.3 V rail that comes up in the S0 (running) state; "CARBON" is just the rail's label. The board data gives its voltage as 3.300.
  • Known-good readings: 3.300 V with the board powered and in S0. No known-good diode or resistance reading is listed for this rail.
  • How to check: With power off, measure diode mode from the rail to ground; then power up and measure the voltage.
  • If it's far off: A missing or low 3.3 V in S0 usually points to the rail's supply or an overload on it, but that's general and not confirmed here. Compare the diode reading against a matching rail on a known-good board before replacing anything.
PP3V3_S0_DPMUX_UC_R0.325––
AI: what PP3V3_S0_DPMUX_UC_R is and how to check it

Reference note for PP3V3_S0_DPMUX_UC_R (820-00281):

  • From the name, this is a 3.3 V rail that runs in the S0 (running) state and feeds the DPMUX/UC section; the "S0" and "3V3" parts come from the rail name, not from measured data.
  • Known-good: diode mode to ground is 0.325. No known-good voltage reading here.
  • Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.325 suggests a short or leaky part on that rail; a missing or low voltage with a good diode reading points more to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP3V3_S0_GPU0.538––
AI: what PP3V3_S0_GPU is and how to check it
  • PP3V3_S0_GPU is a 3.3 V rail (from the "3V3" in its name) that is switched on in the S0 running state (from the "S0" in its name). The "GPU" part of the name suggests it feeds the graphics processor, but that's general naming, not confirmed by board data.
  • Known-good: diode mode to ground 0.538. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point.
  • A diode reading far below 0.538 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. A missing voltage with a good diode reading points upstream, to the rail's enable or supply. These are likely causes, not confirmed ones.
PP3V3_S0_GPUTHMSNS_R0.418––
AI: what PP3V3_S0_GPUTHMSNS_R is and how to check it

PP3V3_S0_GPUTHMSNS_R is a 3.3 V S0 (running-state) rail, judging by its name: a GPU thermal-sense supply that should be present once the board is in S0. The only known-good reading here is a diode value of 0.418 to ground; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.418 usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_S0_LEFT0.355––
AI: what PP3V3_S0_LEFT is and how to check it

PP3V3_S0_LEFT is a 3.3 V rail that, judging by its name, is active in the S0 (running) state — the "LEFT" suffix suggests it feeds the left-hand side of the board, though that's from the name only. The only known-good figure in the archive is a diode reading of 0.355 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.355 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault — compare with a matching rail or a known-good board before replacing anything.

PP3V3_S0_TBTTHMSNS_T_R0.392––
AI: what PP3V3_S0_TBTTHMSNS_T_R is and how to check it

PP3V3_S0_TBTTHMSNS_T_R — from the name, a 3.3 V rail in the S0 (running) state, tied to Thunderbolt thermal sensing (TBT THMSNS). The "_T_R" suffix suggests a sensed or remote-side variant; that part is inference from the name, not from board data.

  • Known-good reading: diode 0.392 in diode mode. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail's test point. Then power up and measure the voltage at the same point.
  • A diode reading far from 0.392 usually points to a short or a damaged component on that rail; a missing voltage with a normal diode reading points more to the rail not being enabled or its source not running.
  • No parts list is available for this net, so the next step is to trace where the 3.3 V comes from and confirm that source is up.
PP3V3_S0_TBTTHMSNS_X_R0.401––
AI: what PP3V3_S0_TBTTHMSNS_X_R is and how to check it
  • What it is: From its name, a 3.3 V S0 (running-state) rail tied to Thunderbolt thermal sensing ("TBTTHMSNS"). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.401 to ground, from the readings archive; treat it as a guide, since readings vary with board state. No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the net to ground; then power up and measure the voltage on the same point.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing 3.3 V with a normal diode reading points upstream to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_DFR0.567––
AI: what PP3V3_S0SW_DFR is and how to check it
  • PP3V3_S0SW_DFR is a 3.3 V rail that is switched on in the S0 (running) state, judging from the name; "DFR" likely refers to a display-related section, but that part is inference from the name, not from board data.
  • Known-good: diode mode to ground 0.567 (board unpowered). No known-good voltage reading here.
  • Check it with the board off in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far from 0.567 suggests a short or open on that net; a missing voltage with a good diode reading points upstream to its enable or source rail.
PP3V3_S0SW_LCD0.566––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a 3.3 V switched LCD rail; the S0SW part of the name (from the name) indicates it is switched on in the S0 running state. The archive lists one known-good reading: diode mode 0.566 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and confirm about 3.3 V appears once the board reaches S0. No known-good voltage reading is listed here, so compare against a matching rail or a known-good board. A diode reading far from 0.566 usually points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0SW_LCD_R0.566––
AI: what PP3V3_S0SW_LCD_R is and how to check it
  • What it is: PP3V3_S0SW_LCD_R is a 3.3 V switched LCD rail; the "S0" in the name marks it as a running-state rail, and "SW" suggests it is switched on rather than always present. This is from the name only.
  • Known-good reading: diode 0.566 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.566. Then power the board and measure the voltage on the rail; expect about 3.3 V once the board is in S0.
  • If it's far off: a diode reading well below 0.566 points to a short or leaky part on the rail; a missing voltage with a normal diode reading points to the switch or enable side. A single reading doesn't confirm a bad part.
PP3V3_TBT_T_S00.3263.300–
AI: what PP3V3_TBT_T_S0 is and how to check it

Reference note for PP3V3_TBT_T_S0 on the 820-00281:

  • From the name, this is a 3.3 V rail for the Thunderbolt ("TBT") section, in the S0 (running) state. The name alone doesn't say which parts it feeds.
  • Known-good readings from the archive: diode 0.326 and voltage 3.300. These are community values and only a guide; the data gives no condition for them.
  • Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good resistance reading is available here.
  • A voltage far below 3.3 V in S0 points to the rail not coming up or being loaded down; a diode reading well below 0.326 suggests a short or leaky load on the rail. Confirm with a second measurement before replacing anything.
PP3V3_TBT_X_S00.3553.300–
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt X side, and the S0 in its name indicates it belongs to the running (S0) state. The archive lists a known-good diode reading of 0.355 and a known-good voltage of 3.300; treat these as a community guide, not a factory spec.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.355.
  • With power applied and the board in S0, measure the voltage and compare with 3.300.

A voltage far below 3.300 with power on points to the rail not coming up or being loaded down; a diode reading far below 0.355 suggests a short or leaky load on the rail. No known-good resistance reading is available here, so a shorted rail would need to be confirmed by lifting or isolating loads rather than by a resistance value.

PP5V_S00.421––
AI: what PP5V_S0 is and how to check it
  • PP5V_S0 is a 5 V rail that is up in the S0 (running) state, judged from the name; the data doesn't say which parts it feeds.
  • Known-good: diode mode to ground 0.421 (no condition recorded). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe to ground, black to the rail. Then power up and measure the voltage.
  • A diode reading far from 0.421 suggests a short or leaky load on the rail; a missing 5 V with a good diode reading points upstream, to its enable or source. Treat both as leads, not proof.
PP5V_S0_ALSCAM_F0.421––
AI: what PP5V_S0_ALSCAM_F is and how to check it
  • What it is: From the name, a 5 V rail (PP5V) that comes up in the S0 running state, feeding the ALS/camera circuit (ALSCAM). The board data has no parts list, so which components sit on it isn't known.
  • Known-good: Diode 0.421 to ground, no condition given. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage at the same point.
  • If it's far off: A much lower diode reading suggests a short or leaky part on the rail; a missing 5 V with a normal diode reading points upstream to the rail's supply or enable. Treat this as a guide, not a confirmed cause.
PP5V_S0_BKLT_A0.412––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A — from its name, a 5 V backlight rail that comes up in the S0 (running) state. The only known-good figure in the readings archive is a diode-mode reading of 0.412; there is no known-good voltage or resistance value here.

  • Check it unpowered in diode mode from the rail to ground, and compare with 0.412. A very low reading (near short) points to a shorted load or capacitor on the rail; a much higher or open reading points to a broken path feeding it.
  • Then power the board and measure the voltage on the rail once the board is in S0. No known-good voltage is recorded here, so compare against a matching backlight rail on a known-good board.
  • A rail that is correct in diode mode but absent under power usually means the enable or supply feeding it is missing, not that the rail itself is shorted.
PP5V_S0_BKLT_DOL––
AI: what PP5V_S0_BKLT_D is and how to check it
  • What it is: From its name, PP5V_S0_BKLT_D is a 5V rail for the display backlight, active in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good readings: The archive gives a diode reading of OL (open, no conduction to ground) on this net. No known-good voltage is recorded here.
  • How to check: With the board unpowered, measure diode mode from PP5V_S0_BKLT_D to ground; then apply power and measure the voltage on the rail.
  • If it's far off: A short or low diode reading points to a fault on the rail or its load; no voltage with power applied points to the rail not being enabled or its source failing. These are likely causes, not confirmed ones.
PP5V_S0_FAN_CONN0.411––
AI: what PP5V_S0_FAN_CONN is and how to check it
  • What it is: PP5V_S0_FAN_CONN is the 5 V fan connector rail. The "S0" in the name marks it as a running-state rail, so it's expected only once the board is fully on, not in standby.
  • Known-good reading: diode mode to ground is 0.411, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and confirm about 5 V at the fan connector.
  • If it's far off: a low diode reading or missing 5 V usually points to a short or a fault on the rail or its supply, but one reading alone doesn't confirm a bad part.
PP5V_S0_GFXIMVP_VDD0.412––
AI: what PP5V_S0_GFXIMVP_VDD is and how to check it
  • What it is: PP5V_S0_GFXIMVP_VDD is a 5 V rail feeding the graphics IMVP supply, and the "S0" in the name marks it as a running-state rail (from the name). The board data here is a readings archive only, so which parts sit on this net isn't known.
  • Known-good reading: diode mode to ground is 0.412. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on that rail; a much higher one to an open feed. A single reading isn't proof, so compare against a known-good board or the matching rail before replacing anything.
PP5V_S0_GFXIMVP_VDDP0.411––
AI: what PP5V_S0_GFXIMVP_VDDP is and how to check it
  • What it is: From the name, a 5 V S0 (running-state) rail feeding the graphics IMVP supply's VDDP. The data doesn't list which parts sit on it.
  • Known-good: diode 0.411 to ground, no condition given. No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage with a normal diode reading points upstream at the supply or its enable. Confirm with a second measurement before replacing anything.
PP5V_S0_GPU_OPAMPOL––
AI: what PP5V_S0_GPU_OPAMP is and how to check it

PP5V_S0_GPU_OPAMP is a 5 V rail for the GPU op-amp supply, and the "S0" in its name indicates it belongs to the running (S0) power state. The only known-good reading here is a diode value of OL (open, no conduction to ground) in diode mode; there is no known-good voltage reading for this rail in the data.

  • Check it with the board unpowered: meter in diode mode, black probe on ground, red probe on the rail, and confirm it reads OL like the known-good value.
  • Then power the board and measure the DC voltage on the rail; it should come up only once the board is in S0.

A diode reading far below OL (a low value) usually points to a short or a leaky part on that rail, while a rail that stays at 0 V with power applied points to the rail not being enabled or its source missing. These are general guidelines, not confirmed causes for this board.

PP5V_S0_GPUFETOL––
AI: what PP5V_S0_GPUFET is and how to check it
  • What it is: From its name, PP5V_S0_GPUFET is a 5 V rail that switches the GPU supply and is active in the S0 (running) state. The name is the only description available here.
  • Known-good readings: The archive lists diode OL for PP5V_S0_GPUFET. No known-good voltage reading exists here, and no condition is recorded for the diode value.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with the OL figure. Then apply power and measure the voltage in the S0 state.
  • What a far-off reading suggests: A diode reading well below OL can mean a short or a leaky load on the rail; a missing 5 V with power applied points to the enable or switch feeding it. Neither is confirmed from one reading, so check the feeding side next.
PP5V_S0_KBD0.432––
AI: what PP5V_S0_KBD is and how to check it

PP5V_S0_KBD is a 5 V rail for the keyboard section, and the S0 in its name indicates the running (S0) power state, so it should come up once the board is fully on. The only known-good figure here is a diode reading of 0.432 to ground; there is no known-good voltage or resistance value for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the same point. A diode reading far below 0.432 usually suggests a short or a leaky part on the rail, while a correct diode reading with no 5 V when the board is running points more to the supply or enable side. Treat the 0.432 as a community guide, not a guaranteed value.

PP5V_S0_T1390.412––
AI: what PP5V_S0_T139 is and how to check it

PP5V_S0_T139 is a 5 V rail at the S0 (running) stage, judging by its name; the board data doesn't say which parts it feeds. Its only known-good reading here is diode mode 0.412 to ground, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare; then apply power and check for about 5 V. A diode reading far from 0.412 usually points to a short or a damaged component on that rail, but one reading isn't proof, and no known-good voltage reading exists here.

PP5V_S0GPU_P1V35_GPU0.413––
AI: what PP5V_S0GPU_P1V35_GPU is and how to check it

PP5V_S0GPU_P1V35_GPU — the name suggests a 5 V rail feeding the GPU section, enabled in the S0 (running) state; that reading is from the name, not the data. Known-good: diode mode to ground 0.413 (board unpowered). No known-good voltage reading here. Check it with the board off in diode mode from the net to ground, then power up and measure the voltage. A diode reading far from 0.413 usually points to a short or a damaged part on that rail, but confirm with a voltage check before replacing anything.

PP5V_S0SW_LCD0.568––
AI: what PP5V_S0SW_LCD is and how to check it
  • What it is: PP5V_S0SW_LCD is a switched 5V LCD rail; the S0 part of the name indicates it belongs to the running (S0) state, and SW suggests it is switched on by a control signal rather than always present.
  • Known-good reading: diode 0.568 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.568; then power up and confirm 5V appears once the board is in S0.
  • If it's far off: a much lower diode reading points to a short or leaky load on the rail, while a missing voltage with a normal diode reading points to the switch or its enable. This is general guidance, not confirmed from this board's data.
PPVCC_S0_CPU0.0031.5001.520R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — the name indicates the CPU core power rail, active in the S0 (running) state; that reading is from the name, not from board data.

  • Known-good readings for this board: diode 0.003, voltage 1.500, resistance 1.520R. Treat these as a community guide, not a spec.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode or resistance far from 0.003 / 1.520R suggests a short or a heavy load on the CPU rail; a missing or wrong voltage with a normal diode reading points more toward the regulator or its enable sequence.
  • No known-good reading of other kinds is listed here. Confirm a suspect rail against a matching net or a known-good board before replacing anything.
PPVCCGT_S0_CPU0.0051.5002.600R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU is the CPU graphics rail; the "S0" in the name marks it as a running-state rail, and "VCCGT" is the usual name for the CPU's integrated graphics supply (that reading is from the name, not from board data). The archive lists diode 0.005, voltage 1.500 and resistance 2.600R for this net, but no condition is recorded, so treat them as a guide only.

  • Check with the board unpowered: diode mode from the rail to ground, then resistance to ground.
  • Then power the board and measure the rail voltage in the S0 running state.
  • A diode or resistance far below the known-good figure points to a short or a heavy load on the rail; a missing voltage with normal diode readings points upstream to the rail's regulator or its enable.
  • No known-good waveform or current draw is recorded here, so a matching net or a known-good board is the only comparison for those.
PPVCCIO_S0_CPU0.0450.95045.000R
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is a CPU I/O supply rail; the S0 in the name indicates it is up in the running state. In this board's readings archive the known-good values are diode 0.045, voltage 0.950 V and resistance 45.000R, with no condition recorded, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode or resistance far below known-good suggests a short or a failing load on the rail; a voltage far off 0.950 V points to the rail not coming up or being pulled down. No known-good waveform or current reading exists here, so compare against a matching rail on a known-good board if needed.

PPVCCSA_S0_CPU0.0141.1507.690R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is a CPU system-agent supply rail; the "S0" in its name means it belongs to the running (S0) power state, and the "CPU" part says it feeds the processor. Known-good readings for this board are diode 0.014, voltage 1.150 V and resistance 7.690R; treat these as a guide since they come from community contributions and vary with board state. To check it, power the board off and measure diode mode to ground, then apply power and measure the voltage on the rail. A reading far from known-good usually points to a short or a failed supply component on that rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything. No known-good value of another kind is listed here.

PPVCORE_S0_GFX_PH10.0031.1002.510R
AI: what PPVCORE_S0_GFX_PH1 is and how to check it

PPVCORE_S0_GFX_PH1 — from the name, the graphics core supply, active in S0 (running) state. It's a CPU/GPU core rail, so it's a low-voltage, high-current rail.

  • Known-good readings from the archive: diode 0.003, voltage 1.100 V, resistance 2.510R. These are community values and only a guide; core rails read very low in diode mode, so a near-zero diode reading is normal here.
  • Check it unpowered in diode mode to ground, then with power applied measure the voltage and compare with 1.100 V.
  • A voltage far from 1.100 V, or a diode/resistance reading far from the listed values, usually points to a short or a fault in the rail's supply — but a small difference can be normal, so confirm with a second measurement before suspecting a part.
  • No known-good reading of other kinds is listed for this rail.
PPVCORE_S0_GFX_PH20.0031.1002.510R
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 — the name indicates the graphics core (GFX) CPU/GPU core supply, in the S0 (running) state; the PH2 suffix is from the name and typically marks a phase of a multiphase core regulator (general naming, not from this board's data).

  • Known-good readings here: diode 0.003, voltage 1.100 V, resistance 2.510R (community guide; no condition stated).
  • Check with the board unpowered: diode mode from the rail to ground, then resistance to ground. Then power up and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a shorted load on the core rail (a shorted phase MOSFET or a shorted die); a voltage that's absent or wrong with a normal diode reading points upstream, at the regulator's enable or supply.
  • No known-good waveform or current reading here; compare against a matching phase or a known-good board of the same model.
PPVCORE_S0_GPU0.0031.1002.510R
AI: what PPVCORE_S0_GPU is and how to check it

PPVCORE_S0_GPU — the GPU core supply, active in the S0 (running) state, judging by the name. Known-good from the readings archive: diode 0.003, 1.100 V, resistance 2.510R. That diode value is very low, which is normal for a big core rail — don't read it as a short on its own.

  • Check with the board unpowered: diode mode, red probe to ground, black to the rail.
  • Then power up and measure the voltage; compare against 1.100 V.
  • A voltage far off, or resistance well away from 2.510R, usually points to a shorted or open load on the rail rather than the regulator itself — but that's a likely cause, not confirmed.

No known-good reading here for in-circuit behaviour under load, so compare against a matching rail or a known-good board.

PPVDDCI_S0_GPU0.0290.90028.000R
AI: what PPVDDCI_S0_GPU is and how to check it

PPVDDCI_S0_GPU — the name indicates a GPU core supply rail (VDDCI), active in the S0 running state; that reading is from the name, not from a schematic.

Known-good readings for this net (community archive, guide only): diode 0.029, voltage 0.900 V, resistance 28.000R. No condition is recorded with them, and there is no separate known-good value beyond these.

To check it: power off and unplug, then measure diode mode from the rail to ground; with power applied, measure the voltage on the rail. A diode or resistance far below known-good suggests a short or heavy load on the rail; a missing or low voltage with a normal diode reading points more toward the supply not being enabled or its upstream rail. These are likely causes, not confirmed ones — compare against a matching rail or a known-good board before replacing anything.

PPVIN_S0_CPUVR_VIN0.457––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VRM input rail; the S0 in the name indicates the running state, and the name itself points to the CPU voltage-regulator supply. The only known-good figure in the archive is a diode reading of 0.457 to ground; there is no known-good voltage or resistance value here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.457.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far below 0.457 usually suggests a short or a leaky part on the rail; a far higher or open reading points to a broken connection. A small difference can be normal, so confirm with a voltage check before replacing anything.
PPVIN_S0_GFXIMVP_VIN0.448––
AI: what PPVIN_S0_GFXIMVP_VIN is and how to check it
  • What it is: From the name, PPVIN_S0_GFXIMVP_VIN is the input supply for the graphics IMVP regulator, active in the S0 (running) state. The name is the only description available here.
  • Known-good reading: diode 0.448 to ground, from the readings archive. That is the only value recorded for this rail; there is no known-good voltage or resistance here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.448. Then power the board and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.448 suggests a short or a leaky part on the rail; well above it can mean an open feed. A missing voltage with a normal diode reading points upstream, to the source feeding this rail. These are general guidelines, not confirmed causes for this board.
PPVIN_S0GPU_1V8_RC0.456––
AI: what PPVIN_S0GPU_1V8_RC is and how to check it
  • What it is: From the name, a 1.8 V GPU input rail that is up in the S0 (running) state. The name is the only description available here.
  • Known-good reading: diode mode to ground 0.456, with no condition listed. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a damaged part on that rail; a much higher one to an open path. A single reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.
PPVIN_S0SW_LCDBKLT0.87913.100–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the switched input feed for the LCD backlight, from its name: an S0 (running-state) rail, so it should only be present once the board is powered on. The archive lists a known-good diode reading of 0.879 and a voltage of 13.100; no condition is recorded for either, so treat them as a guide.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.879.
  • With power applied, measure the voltage and compare with 13.100.

A far lower diode reading usually suggests a short or a leaky part on the rail; no voltage when the board is running points to the backlight enable or switch side not coming up. There is no known-good resistance reading for this rail.

PPVIN_S0SW_LCDBKLT_FET0.45013.1000.115R
AI: what PPVIN_S0SW_LCDBKLT_FET is and how to check it

PPVIN_S0SW_LCDBKLT_FET — the name indicates the switched input feed to the LCD backlight, active in the S0 (running) state; that reading is from the name, not from board data.

  • Known-good readings in the archive: diode 0.450, voltage 13.100, resistance 0.115R. These are community values and only a guide; the data gives no condition for them.
  • Check with the board unpowered: diode mode, black probe to ground, red probe on the rail, and compare with 0.450. Then power up and measure the voltage, expecting about 13.1 V once the board is in S0.
  • A diode reading far from 0.450 suggests a short or a leaky part on the rail; a missing or low voltage with a good diode reading points upstream, at the backlight enable/switch circuit or its supply.
  • No known-good value of another kind is listed here, so compare against a matching net on a known-good board if you have one.
PPVIN_S0SW_LCDBKLT_R0.45013.1000.115R
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the LCD backlight input rail; the S0 part of the name indicates it belongs to the running state, and LCDBKLT marks it as backlight-related (from the name). The archive lists a known-good diode reading of 0.450 to ground, 13.100 V with power applied, and 0.115R resistance. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.450 suggests a short or leaky load on the backlight side; a missing or low voltage with a good diode reading points upstream at the backlight supply, not the rail itself. These are community readings and only a guide, and no known-good resistance condition is recorded here.

PPVOUT_S0_LCDBKLT1.22859.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight output rail; the "S0" in the name marks it as a running-state rail, and "LCDBKLT" says it feeds the backlight. The archive lists a known-good diode reading of 1.228 and a voltage of 59.000, with no condition noted, so treat them as a guide. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and the display connected. A diode reading far below known-good usually points to a short or leaky part on the rail; a voltage far off suggests the backlight driver isn't running or the rail isn't being enabled. No known-good resistance reading is listed here.

Repair notes

CD3215 Repeat checks for each unit, U3100,3200, UB300, 400

UB300

0V6 diode mode on USBC_TA_CC1 at CB313 pin 1 0V6 diode mode on USBC_TA_CC2 at CB314 pin 1 5V on FB200 pin 1 3V3 on CB308 pin 1 1V8 on CB305 pin 1 1V8 on CB306 pin 1 1V1 on CB304 pin 1 ~26V on QB300 pin 1 and QB300 pin 4 Check PPDCIN_G3H on QB300 pin 8

UB400

0V6 diode mode on USBC_TB_CC1 at CB413 pin 1 0V6 diode mode on USBC_TB_CC2 at CB414 pin 1 5V on FB201 pin 1 3V3 on CB408 pin 1 1V8 on CB405 pin 1 1V8 on CB406 pin 1 1V1 on CB404 pin 1 ~26V on QB400 pin 1 and QB400 pin 4 Check PPDCIN_G3H on QB400 pin 8

U3100

0V6 diode mode on USBC_XA_CC1 at C3113 pin 1 0V6 diode mode on USBC_XA_CC2 at C3114 pin 1 5V on F3000 pin 1 3V3 on C3108 pin 1 1V8 on C3105 pin 1 1V8 on C3106 pin 1 1V1 on C3104 pin 1 Check 26V on Q3100 pin 1 and Q3100 pin 4 Check PPDCIN_G3H on Q3100 pin 8

U3200

0V6 diode mode on USBC_XB_CC1 at C3213 pin 1 0V6 diode mode on USBC_XB_CC2 at C3214 pin 1 5V on F3001 pin 1 3V3 on C3208 pin 1 1V8 on C3205 pin 1 1V8 on C3206 pin 1 1V1 on C3204 pin 1 Check 26V on Q3200 pin 1 and Q3200 pin 4 Check PPDCIN_G3H on Q3200 pin 8

CD3215 Full Sequence 5V to 20V

Data comms for USB-C PD (CC1/2)... 0V6 diode mode on USBC_XA_CC1 at C3113 pin 1 0V6 diode mode on USBC_XA_CC2 at C3114 pin 1 Power getting to the CD3215... 5V on PP20V_USBC_XA_VBUS at F3000 pin 1 Basic CD3215 voltages + LDOs... 3V3 on PP3V3_UPC_XA_LDO at C3108 pin 1 1V8 on PP1V8_UPC_XA_LDOA at C3106 pin 1 1V8 on PP1V8_UPC_XA_LDOD at C3105 pin 1 1V1 on PP1V1_UPC_XA_LDO_BMC at C3104 pin 1 Open Q3100 so power goes through to PPDCIN_G3H... >5V on UPC_XA_GATE1 at Q3100 pin 1 >5V on UPC_XA_GATE2 at Q3100 pin 4 5V on PPDCIN_G3H at CC773 pin 1 Power to the ISL U7000 ... (in) 5V on TBA_VDDA at C7075 pin 1 (out) >=3V3 on PM_EN_P3V3_G3H at R6921 pin 1 Getting PP3V3_G3H ... 3V3 on PP3V3_G3H at L6900 pin 1 SMC rails... 1V2 on PP1V2_S5_SMC_VDDC at C5012 pin 1 3V0 on PP3V0_S5_AVREF_SMC at C5020 pin 1 ~3V3 on [n:SMBUS_SMC_4_G3H_SCL at R5321 pin 2 (0V66 DM) ~3V3 on [n:SMBUS_SMC_4_G3H_SDA at R5320 pin 2 (0V66 DM) USBC CC1/2... 0V8 on USB_XA_CC1 at C3113 pin 1 0V8 on USB_XA_CC2 at C3114 pin 1 20V switch over... 20V on PP20V_USBC_XA_VBUS at F3000 pin 1 >20V on UPC_XA_GATE1 at Q3100 pin 1 >20V on UPC_XA_GATE2 at Q3100 pin 4 20V on PPDCIN_G3H at CC773 pin 1 Final steps... 5V on TBA_AUX_DET at C7016 pin 1 3V3 on SMC_RST_L at R7090 pin 1 MOSFETS Q7030 and Q7040 should now be open and U7000 should be generating PPBUS_G3H

Every net with a reading

NetDiodeVoltageResistance
5VS4_VFB1_RR0.623––
50_0_ANT0.005––
50_1_ANT0.005––
50_2_ANT0.005––
8409_ASP1_LRCLK0.364––
8409_ASP1_SCLK0.363––
8409_ASP1_SCLK_R0.363––
8409_ASP1_SDOUT0.364––
8409_ASP1_SDOUT_R0.364––
8409_ASP2_LRCLK0.671––
8409_ASP2_LRCLK_R0.671––
8409_ASP2_SCLK0.527––
8409_ASP2_SCLK_R0.525––
8409_ASP2_SDOUT0.517––
8409_HDA_SDIN0_R0.524––
8409_I2C_SCL0.361––
8409_I2C_SDA0.440––
8409_VA_PLL0.610––
ACT_GND0.000––
ADC1_REFCOMPOL––
ADC2_REFCOMPOL––
ALL_SYS_PWRGD0.455––
ALS_SCL_I2C_1V80.457––
ALS_SDA_I2C_1V80.458––
ALS_SOC_UART_D2R0.514––
ALS_SOC_UART_R2D0.515––
AP_CLKREQ_L0.574––
AP_PCIE_WAKE_L0.486––
AP_RESET_L0.589––
AP_S0IX_WAKE_L0.509––
AP_S0IX_WAKE_SEL0.725––
AUD_ASP1A_LRCLK0.376––
AUD_ASP1A_SCLK0.376––
AUD_ASP1A_SDOUT0.356––
AUD_ASP1B_LRCLK0.355––
AUD_ASP1B_SCLK0.356––
AUD_ASP1B_SDOUT0.357––
AUD_ASP2_SDIN0.672––
AUD_CODEC_INT_L0.709––
AUD_CODEC_RESET_L0.718––
AUD_CODEC_WAKE_L0.809––
AUD_CONN_HP_LEFT0.680––
AUD_CONN_HP_RIGHT0.680––
AUD_CONN_HP_SENSE_L1.550––
AUD_CONN_HP_SENSE_R1.550––
AUD_CONN_RING20.020––
AUD_CONN_RING2_XW0.649––
AUD_CONN_SLEEVE0.020––
AUD_CONN_SLEEVE_XW0.654––
AUD_CONN_TIP_SENSEOL––
AUD_HP_PORT_CH_GND0.020––
AUD_HP_PORT_L0.680––
AUD_HP_PORT_R0.680––
AUD_HP_PORT_US_GND0.020––
AUD_HP_SENSE_L0.155––
AUD_HP_SENSE_R1.550––
AUD_HS_MIC_N0.649––
AUD_HS_MIC_P0.654––
AUD_I2C_1A_SCL0.354––
AUD_I2C_1A_SDA0.435––
AUD_I2C_1B_SCL0.357––
AUD_I2C_1B_SDA0.435––
AUD_PWR_EN0.530––
AUD_SPI_MOSI0.556––
AUD_SPKRAMP_INT_L0.402––
AUD_SPKRAMP_RESET_L0.363––
AUD_TIP_SENSE1.415––
BKLT_PWM_MLB2TCON0.654––
BKLT_PWM_TCON2MLB0.764––
BKLT_SD0.600––
BMON_IOUT_DOL––
BT_I2S_CLK0.565––
BT_I2S_D2R_R0.551––
BT_I2S_R2D0.580––
BT_I2S_SYNC0.576––
BT_LOW_PWR_L0.548––
BT_TIMESTAMP0.567––
BT_UART_CTS_R2D_L0.493––
BT_UART_D2R0.418––
BT_UART_R2D0.495––
BUF_EDP_PANEL_PWR_EN0.717––
BUF_SMC_RESET_L0.701––
CAMERA_PWR_EN0.792––
CHGR_AMON0.615––
CHGR_BMON0.616––
COMP_A_CPUCORE0.628––
COMP_A_CPUCORE_LOL––
COMP_B_CPUGT0.628––
COMP_B_CPUGT_LOL––
CORE2_5G_CTL2_WLAN_JTAG_TDO0.605––
CPU_CATERR_L0.232––
CPU_CFG_RCOMP0.054–52.900R
CPU_CFG<0>0.288––
CPU_CFG<1>0.288––
CPU_CFG<2>0.288––
CPU_CFG<3>0.285––
CPU_CFG<8>0.286––
CPU_CFG<9>0.280––
CPU_CFG<10>0.287––
CPU_CFG<11>0.288––
CPU_CFG<12>0.290––
CPU_CFG<16>0.291––
CPU_CFG<17>0.293––
CPU_CFG<18>0.289––
CPU_CFG<19>0.291––
CPU_DC_B2_C1OL––
CPU_DC_B38_C38OL––
CPU_DC_BR1_BR20.346––
CPU_DC_BR2_BR1OL––
CPU_DC_BR38_BT360.002––
CPU_DC_BT36_BR380.002––
CPU_DC_C1_B2OL––
CPU_DC_C38_B38OL––
CPU_DIMM_VREFCA0.693––
CPU_DIMMA_VREFDQ0.756––
CPU_DIMMB_VREFDQ0.756––
CPU_EDP_RCOMP0.066––
CPU_EOPIO_RCOMP0.001––
CPU_OPC_OPIO_RCOMP0.004–2.900R
CPU_OPC_OPIO_RCOMP_ED20.003–2.200R
CPU_PCH_PM_DOWN0.310––
CPU_PCH_PM_DOWN_R0.287––
CPU_PCH_TRIGGER0.322––
CPU_PCH_TRIGGER_R0.287––
CPU_PECI0.299––
CPU_PECI_R0.275––
CPU_PROCHOT_L0.501––
CPU_PROCHOT_R_L0.287––
CPU_PWRGD0.474––
CPU_RESET_L0.479––
CPU_VCCSASENSE_N0.003–25.300R
CPU_VCCSASENSE_P0.016–16.200R
CPU_VCCST_PWRGD0.447––
CPU_VIDALERT_L0.272––
CPU_VIDALERT_R_L0.492––
CPU_VIDSCLK0.229––
CPU_VIDSCLK_R0.228––
CPU_VIDSOUT0.230––
CPU_VIDSOUT_R0.230––
CPU_VR_EN_R0.472––
CPUCORE_ISEN10.629––
CPUCORE_ISEN30.629––
CPUCORE_ISNS1_N0.0031.5001.520R
CPUCORE_ISNS1_P0.0031.5001.520R
CPUCORE_ISNS2_N0.0031.5003.000R
CPUCORE_ISNS2_P0.0031.5003.000R
CPUCORE_ISNS3_N0.0031.5001.520R
CPUCORE_ISNS3_P0.0031.5001.520R
CPUCORE_PSYS0.625––
CPUCORE_PWM20.610––
CPUCORE_SW10.0031.500–
CPUCORE_SW20.0031.5003.000R
CPUCORE_SW30.0031.5003.000R
CPUGT_BOOT10.608––
CPUGT_BP10.608––
CPUGT_ISEN20.629––
CPUGT_ISNS1_N0.0051.5004.800R
CPUGT_ISNS1_P0.0051.5004.800R
CPUGT_ISNS2_N0.0051.5002.600R
CPUGT_ISNS2_P0.0051.5002.600R
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN0.007––
CPUGT_PHASE10.008––
CPUGT_SW10.0051.5004.800R
CPUGT_SW20.0051.5004.800R
CPUGTVSENSE_IN0.008––
CPUHI_COMP_FBOL––
CPUHI_COMP_OUTOL––
CPUHI_COMP_VREFOL––
CPUHI_IOUT0.709––
CPUHI_IOUT_ROL––
CPUSA_FCCM0.613––
CPUSA_ISNS_N–1.1507.690R
CPUSA_ISNS_P–1.1507.690R
CPUSA_ISUMN0.015–35.500R
CPUSA_ISUMN_R0.487––
CPUSAVSENSE_IN0.014––
CPUTHMSNS_ALERT_L0.596––
CPUTHMSNS_THM_L0.639––
CPUVR_ISUM_IOUTOL––
CPUVR_PGOOD0.516––
CPUVR_SWSA0.0141.15013.500R
CPUVSENSE_IN0.005––
DBGLED_GPUOL––
DBGLED_GPU_DOL––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S0I3OL––
DBGLED_S0I3_DOL––
DBGLED_S3OL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DBGLED_S5OL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.490––
DEBUGUART_SEL_SOC0.574––
DFR_CLKIN_RESET_L0.479––
DFR_DISP_INT0.474––
DFR_DISP_PWR_EN0.527––
DFR_DISP_RESET_L0.703––
DFR_DISP_RST_L0.464––
DFR_DISP_SMC_RST_L0.532––
DFR_DISP_VSYNC0.480––
DFR_TOUCH_GPIO20.479––
DFR_TOUCH_INT_L0.476––
DFR_TOUCH_LID0.511––
DFR_TOUCH_PANEL_DETECT0.477––
DFR_TOUCH_RESET_L0.475––
DFR_TOUCH_ROM_I2C_SCL0.474––
DFR_TOUCH_ROM_I2C_SDAOL––
DFR_TOUCH_ROM_WCOL––
DFR_TOUCH_SPI_CLK_R0.477––
DFR_TOUCH_SPI_CS_L0.474––
DFR_TOUCH_SPI_MISO0.475––
DFR_TOUCH_SPI_MISO_R0.477––
DFR_TOUCH_SPI_MOSI_R0.476––
DFRDRV_I2C_SCL0.472––
DFRDRV_I2C_SDA0.472––
DFU_SPI_STATUS0.477––
DFU_STATUS0.477––
DMIC1_CLK0.793––
DMIC1_DATA0.760––
DMIC2_CLK0.793––
DMIC2_DATA0.760––
DP_INT_EG_HPD0.350––
DP_INT_HPD0.624––
DP_INT_IG_HPDOL––
DP_T_SNK0_DDC_CLK0.602––
DP_T_SNK0_HPD0.579––
DP_T_SNK0_HPD_EG0.356––
DP_T_SNK0_HPD_IG0.553––
DP_T_SNK1_DDC_CLK0.619––
DP_T_SNK1_HPD0.581––
DP_T_SNK1_HPD_EG0.356––
DP_T_SNK1_HPD_IG0.623––
DP_T_SRC_HPD0.599––
DP_TB_HPD0.595––
DP_X_SNK_RBIAS0.781––
DP_X_SNK0_DDC_CLK0.575––
DP_X_SNK0_DDC_DATA0.574––
DP_X_SNK0_HPD0.560––
DP_X_SNK0_HPD_EG0.358––
DP_X_SNK0_HPD_IG0.555––
DP_X_SNK1_DDC_CLK0.576––
DP_X_SNK1_DDC_DATA0.575––
DP_X_SNK1_HPD0.560––
DP_X_SNK1_HPD_EG0.356––
DP_X_SNK1_HPD_IG0.553––
DP_X_SRC_HPD0.575––
DP_X_SRC_RBIAS0.801––
DP_XA_HPD0.572––
DPMUX_LRESET_L0.587––
DPMUX_UC_IRQ0.611––
DPMUX_UC_MD10.618––
DPMUX_UC_MD20.576––
DPMUX_UC_MD2_R0.576––
DPMUX_UC_RESET_L0.512––
DPMUX_UC_RX0.599––
DPMUX_UC_TCK0.646––
DPMUX_UC_TDI0.649––
DPMUX_UC_TDO0.649––
DPMUX_UC_TMS0.647––
DPMUX_UC_TRST_L0.648––
DPMUX_UC_TX0.603––
DPMUX_UC_VCL0.465––
EADC1_LCDBKLT_ISENSEOL––
EADC1_OTHER5V_HI_ISENSEOL––
EADC1_PP3V3S4_WLAN_ISENSEOL––
EADC1_PP5V_T139_ISENSEOL––
EADC1_TBT_T_ISENSEOL––
EADC2_AD0OL––
EADC2_BT_ISENSEOL––
EADC2_CAMERA_ISENSEOL––
EADC2_KBBLT_ISENSEOL––
EADC2_LCDPANEL_ISENSEOL––
EADC2_OTHER3V3_HI_ISENSEOL––
EADC2_PP3V3_TPAD_ISENSEOL––
EADC2_T151_ISENSEOL––
EDP_AUXCH_C_N0.445––
EDP_AUXCH_C_P0.448––
EDP_BKLT_EN0.531––
EDP_IG_BKLT_EN0.640––
EDP_IG_PANEL_PWR_EN0.690––
EDP_INT_ML_N<0>0.401––
EDP_INT_ML_N<1>0.399––
EDP_INT_ML_N<2>0.399––
EDP_INT_ML_N<3>0.433––
EDP_INT_ML_P<0>0.399––
EDP_INT_ML_P<1>0.399––
EDP_INT_ML_P<2>0.399––
EDP_INT_ML_P<3>0.407––
EDP_PANEL_PWR_EN0.558––
EG_BKLT_EN0.357––
EG_CLKREQ_OUT_L0.551––
EG_CLKREQ_PU0.600––
EG_CLKREQ_SEL_L0.639––
EG_LCD_PWR_EN0.357––
EG_PEG_CLK100M_N0.403––
EG_PEG_CLK100M_P0.415––
EG_RAIL1_EN0.564––
EG_RAIL2_EN0.688––
EG_RAIL4_EN0.634––
EG_RAIL5_EN0.585––
EG_RESET_L0.530––
FAN_LT_PWM0.944––
FAN_LT_TACHOL––
FAN_RT_PWM0.953––
FAN_RT_TACHOL––
FB_A0_MF0.122––
FB_A0_SEN0.122––
FB_A0_VREFC0.310––
FB_A0_VREFD0.593––
FB_A0_ZQ0.121––
FB_A1_MF0.122––
FB_A1_SEN0.121––
FB_A1_VREFC0.312––
FB_A1_VREFD0.588––
FB_A1_ZQ0.122––
FB_B0_MF0.121––
FB_B0_SEN0.121––
FB_B0_VREFC0.313––
FB_B0_VREFD0.592––
FB_B0_ZQ0.122––
FB_B1_MF0.121––
FB_B1_SEN0.122––
FB_B1_VREFC0.311––
FB_B1_VREFD0.590––
FB_B1_ZQ0.122––
FBVDD_ALTVO0.544––
GFX_SELF_THROTTLE0.358––
GFX_SELF_THROTTLE_R0.358––
GFXIMVP_ISNS1_N0.0031.1002.510R
GFXIMVP_ISNS1_P0.0031.1002.510R
GFXIMVP_ISNS2_N0.0031.1002.510R
GFXIMVP_ISNS2_P0.0031.1002.510R
GFXIMVP_ISUM_IOUTOL––
GFXIMVP_ISUMN0.004––
GFXIMVP_ISUMP_COL––
GFXIMVP_PHASE10.0031.1002.510R
GFXIMVP_PHASE20.0031.1002.700R
GMUX_SLP_S3_BUF_L0.512––
GPU_ANALOGIO0.721––
GPU_AUD_PORT_CONN<0>0.389––
GPU_AUD_PORT_CONN<1>0.389––
GPU_AUD_PORT_CONN<2>0.390––
GPU_AUD<0>0.353––
GPU_AUX_ZVSS0.152––
GPU_BP_10.396––
GPU_BRD_CFG<0>0.391––
GPU_BRD_CFG<1>0.390––
GPU_BRD_CFG<2>0.390––
GPU_CLKREQ_L0.433––
GPU_DBG_80.397––
GPU_DBG_90.396––
GPU_DBG_100.397––
GPU_DBG_110.398––
GPU_DIECRACKMON0.001––
GPU_FB_SNS_COMMON_NEG0.001––
GPU_GFX_OVERTEMP0.597––
GPU_GFX_PWR_LEVEL_L0.367––
GPU_GFX_PWR_LEVEL_R_L0.367––
GPU_GPIO_SVC_R0.400––
GPU_GPIO_SVD_R0.396––
GPU_JTAG_TCK0.359––
GPU_JTAG_TDI0.358––
GPU_JTAG_TDO0.359––
GPU_JTAG_TMS0.358––
GPU_JTAG_TRST_L0.360––
GPU_MPLS_PS_00.397––
GPU_MPLS_PS_10.397––
GPU_MPLS_PS_20.395––
GPU_MPLS_PS_30.397––
GPU_PCIE_ZVSS0.202––
GPU_PLLCHARZ_H0.308––
GPU_PLLCHARZ_RC_HOL––
GPU_ROM_CONFIG<0>0.366––
GPU_ROM_CONFIG<1>0.354––
GPU_ROM_CONFIG<2>0.352––
GPU_ROM_CS_L0.384––
GPU_ROM_CS_L_R0.351––
GPU_ROM_SI_R0.352––
GPU_ROM_WP_L0.490––
GPU_SMB_CLK0.431––
GPU_SMB_DAT0.431––
GPU_SMBUS_ADDR<0>0.392––
GPU_SMBUS_ADDR<1>0.390––
GPU_TEST_EN0.809––
GPU_TEST_PG0.788––
GPU_TEST_PG_BACON0.806––
GPU_TX_DEEMPH_EN0.367––
GPU_TX_HALF_SWING0.354––
GPU_VCORE_LOAD0.053––
GPU_VCORE_PCC0.407––
GPU_VCORE_SOURCE0.051––
GPU_VGA_DIS0.354––
GPU_VRAM_STRAP0.358––
GPUCOREVSENSE_IN0.005––
GPUFB_AGND0.001––
GPUFB_BOOT_RC0.564––
GPUFB_CS_N0.0531.500170.000
GPUFB_CS_P0.0531.500170.000
GPUFB_DRVH0.539––
GPUFB_DRVL0.472––
GPUFB_FSEL0.546––
GPUFB_GPU_VO_R0.053––
GPUFB_LL0.0531.500170.000
GPUFB_OCSET0.542––
GPUFB_PGOOD0.527––
GPUFB_RTN_DIV0.526––
GPUFB_SENSE_DIV0.528––
GPUFB_SET_R0.545––
GPUFB_SET00.546––
GPUFB_SREF0.545––
GPUFB_VO0.541––
GPUTHMSNS_D1_P0.713––
GPUTHMSNS_D2_N0.711––
GPUVCORE_COMP0.600––
GPUVCORE_FB_ROL––
GPUVCORE_NTC0.625––
GPUVCORE_PGOOD0.575––
GPUVCORE_SVC0.441––
GPUVCORE_SVT0.544––
GPUVDDCIVSENSE_IN0.037––
GT_ISUMN_R1.018––
HALL_SENSOR_LEFT0.479––
HALL_SENSOR_RIGHT0.484––
HDA_BIT_CLK0.741––
HDA_RST_L0.741––
HDA_SDIN00.524––
HDA_SDOUT0.741––
HDA_SYNC0.742––
HPWR_EN_L0.625––
HS_OTHER3V3_IOUTOL––
I2C_ALS_SCL0.571––
I2C_ALS_SDA0.586––
I2C_BKLT_SCL0.538––
I2C_BKLT_SDA0.622––
I2C_CAM_SCL0.472––
I2C_CAM_SDA0.472––
I2C_DPMUX_UC_SCL0.609––
I2C_DPMUX_UC_SDA0.610––
I2C_GPU_PCC_SCL0.430––
I2C_GPU_PCC_SDA0.430––
I2C_SSD_SCL0.671––
I2C_SSD_SDA0.669––
I2C_TBT_T_SCL0.594––
I2C_TBT_T_SDA0.593––
I2C_TBT_TA_INT_L0.591––
I2C_TBT_TB_INT_L0.590––
I2C_TBT_X_SCL0.570––
I2C_TBT_X_SDA0.569––
I2C_TBT_XA_INT_L0.570––
I2C_TBT_XB_INT_L0.572––
I2C_UPC_T_SCL20.676––
I2C_UPC_T_SDA20.676––
I2C_UPC_TB_DBG_CTL_SDA0.778––
I2C_UPC_X_SCL20.694––
I2C_UPC_X_SDA20.694––
I2C_UPC_XA_DBG_CTL_SDA0.776––
I2C_UPC_XB_DBG_CTL_SCL0.776––
I2C_UPC_XB_DBG_CTL_SDA0.777––
IAPC_OPA_OUTOL––
IMON_A_CPUCORE0.629––
IMON_B_CPUGT0.628––
IMON_C_CPUSA0.628––
ISNS_1V0_N0.0561.00055.000R
ISNS_1V0_P0.0561.00055.000R
ISNS_1V8_SUS_NOL––
ISNS_1V8_SUS_POL––
ISNS_BT_NOL––
ISNS_BT_POL––
ISNS_CAMERA_IOUTOL––
ISNS_CPUDDR_IOUTOL––
ISNS_CPUDDR_NOL––
ISNS_CPUDDR_POL––
ISNS_CPUHIGAIN_OUTOL––
ISNS_CPUSA_IOUTOL––
ISNS_DDR_IOUTOL––
ISNS_GPU_HS_IOUT0.711––
ISNS_GPU_HS_N0.45012.6000.115R
ISNS_GPU_HS_P0.45012.6000.115R
ISNS_GPU1V8_IOUTOL––
ISNS_GPUFB_IOUT0.000––
ISNS_GPUFBIC_IOUTOL––
ISNS_GPUFBIC_NOL––
ISNS_GPUFBIC_POL––
ISNS_GPUVDDCI_IOUTOL––
ISNS_HS_COMPUTING_N0.45013.1000.115R
ISNS_HS_COMPUTING_P0.45013.1000.115R
ISNS_KBBLT_IOUTOL––
ISNS_KBBLT_NOL––
ISNS_KBBLT_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.45013.1000.115R
ISNS_LCDBKLT_P0.45013.1000.115R
ISNS_LCDPANEL_IOUTOL––
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_LPDDR_N0.352–0.900R
ISNS_LPDDR_P0.352–0.900R
ISNS_PP3V3_TPAD_IOUTOL––
ISNS_PP3V3_TPAD_NOL––
ISNS_PP3V3_TPAD_POL––
ISNS_PP3V3S0_IOUTOL––
ISNS_PP3V3S4_WLAN_IOUTOL––
ISNS_PP5V_T139_IOUTOL––
ISNS_PP5V_T139_NOL––
ISNS_PP5V_T139_POL––
ISNS_SSDNAND_IOUTOL––
ISNS_T139_NOL––
ISNS_T139_POL––
ISNS_T151_IOUTOL––
ISNS_TBT_T_IOUTOL––
ISNS_TBT_T_NOL––
ISNS_TBT_T_POL––
ISNS_TBT_X_IOUTOL––
ISNS_TBT_X_NOL––
ISNS_TBT_X_POL––
ISNS_TPAD_NOL––
ISNS_TPAD_POL––
ISNS_WLAN_NOL––
ISNS_WLAN_POL––
ISNS_WLAN_R_NOL––
ISNS_WLAN_R_POL––
ISNS_X239_INT_IOL––
ISNS_X239_INT_NIOL––
ISNS_X239_IOUTOL––
ISNS_X239_IOUT_BUFOL––
ISNS_X239_IOUT_INTOL––
ITP_PMODE0.511––
JTAG_ISP_TCK0.547––
JTAG_ISP_TDI0.547––
JTAG_ISP_TDO0.544––
JTAG_TBT_T_TMS0.594––
JTAG_TBT_TCK0.545––
JTAG_TBT_TDI0.546––
JTAG_TBT_W_TMS0.787––
JTAG_TBT_X_TMS0.566––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_I2C_SCLOL––
KBD_I2C_SDAOL––
KBD_INT_LOL––
L83_FILTP0.862––
L83_FLYC0.410––
L83_FLYP0.520––
L83_HSBIAS_FILT0.720––
L83_HSBIAS_FILT_REF0.636––
L83_SDOUT0.744––
L83_VCP0.480––
L83_VL0.480––
L83_VP0.418––
LBW_AMP_OUTOL––
LBW_AMP_OUT_ROL––
LCD_FSS0.657––
LCD_IRQ_L0.803––
LCD_MUX_EN0.633––
LCD_MUX_SEL0.637––
LCD_PSR_EN0.792––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.731––
LCDBKLT_SW0.440––
LCDBKLT_TB_XWR–59.000–
LPC_AD<0>0.615––
LPC_AD<1>0.572––
LPC_AD<2>0.568––
LPC_AD<3>0.566––
LPC_CLK24M_DPMUX_UC_R0.599––
LPC_CLKRUN_L0.615––
LPC_FRAME_L0.573––
LPC_PWRDWN_L0.573––
LPC_SERIRQ0.589––
MEM_VREFCA_A_RC0.026–25.600R
MEM_VREFDQ_A_RC0.026–25.600R
MEM_VREFDQ_B_RC0.026––
MENU_KEY_L0.737––
MESA_BOOST_EN0.506––
MESA_BOOST_EN_CONN1.212––
MESA_I2C_SCL0.572––
MESA_I2C_SDA0.574––
MESA_PWR_EN0.508––
MESA_SNSR_INT0.485––
MESA_SNSR_INT_CONN1.210––
MESA_SPI_CLK_CONN0.554––
MESA_SPI_CLK_R0.486––
MESA_SPI_MISO_CONN0.539––
MESA_SPI_MOSI_CONN0.564––
MIPI_CLK_CONN_N0.550––
MIPI_CLK_CONN_P0.550––
MIPI_DATA_CONN_N0.553––
MIPI_DATA_CONN_P0.555––
MIPIC_CLK_N0.550––
MIPIC_CLK_P0.550––
MIPIC_DATA_N0.553––
MIPIC_DATA_P0.555––
MIPID_CLK_CONN_N0.546––
MIPID_CLK_CONN_P0.546––
MIPID_CLK_N0.546––
MIPID_CLK_P0.546––
MIPID_DATA_CONN_N0.546––
MIPID_DATA_CONN_P0.546––
MIPID_DATA_N0.546––
MIPID_DATA_P0.546––
MLB_BOARD_ID00.787––
MLB_BOARD_ID20.787––
MLB_BOARD_ID30.726––
MLB_BOARD_ID40.622––
MLB_RAMCFG00.789––
MLB_RAMCFG10.524––
MLB_RAMCFG20.790––
MLB_RAMCFG30.522––
MLB_RAMCFG40.777––
NTC_A_CPUCORE0.630––
NTC_A_CPUCORE_ROL––
P0V9_TBT_T_SVR_AGND0.020––
P0V9_TBT_X_SVR_AGND0.001––
P1V0_SSD_CORE_SW0.3381.000–
P1V0S3_EN0.573––
P1V1_SSD_PCIE_SW0.3511.100–
P1V2_PHASE0.2241.200–
P1V2_SSD_DRAM_SW0.3031.200–
P1V2_SW_SNUBOL––
P1V2_VBST_R0.611––
P1V2S0SW_RAMPOL––
P1V2S3_ILIM_HS0.486––
P1V8_SSD_DRAM_SW0.3971.800–
P1V8_SSD_FMC_SW0.3661.800–
P1V8GPU_PGOOD0.586––
P1V8S3_EN0.498––
P1V8S3_RAMP0.630––
P1V8SUS_IOUTOL––
P1V8SUS_SW0.4351.800–
P1VS0SW_EN_RC0.570––
P1VS4_ILIM_HS0.485––
P1VS4_PHASE0.0561.00055.000R
P1VS4_SW0.054–54.000R
P1VS4_VBST0.591––
P1VS4_VBST_R0.590––
P1VSUS_PGOOD0.472––
P3V3_TBT_T_SX_EN_R0.7403.3000.095R
P3V3_TBT_X_SX_EN_R0.7103.300–
P3V3G3H_AGND0.000––
P3V3G3H_BIAS0.544––
P3V3G3H_FB_R1.211––
P3V3G3H_LX0.3503.300–
P3V3G3H_VBST_R0.592––
P3V3GPU_EN0.564––
P3V3GPU_RAMP0.627––
P3V3S0_CAP0.575––
P3V3S5_CSN20.3903.300–
P3V3S5_CSP2_R–5.000–
P3V3S5_RF0.591––
P3V3S5_VFB2_R0.380––
P3V3S5_VSW0.3903.300–
P5_S0GPU_PGOOD0.650––
P5VGPU_RAMPOL––
P5VS0_VBST_R0.635––
P5VS4_COMP10.750––
P5VS4_COMP1_ROL––
P5VS4_CSN10.4255.000–
P5VS4_CSP1_R0.4255.000–
P5VS4_DRVH0.979––
P5VS4_PGOOD0.460––
P5VS4_VFB1_R0.424––
P5VS4_VSW0.4255.000–
P5VUSBCT_AGND0.001––
P5VUSBCT_BOOT_RC0.601––
P5VUSBCT_DRVH0.676––
P5VUSBCT_DRVH_R0.676––
P5VUSBCT_DRVL0.453––
P5VUSBCT_FSEL0.545––
P5VUSBCT_LL0.2115.000–
P5VUSBCT_N0.2115.000–
P5VUSBCT_OCSET0.539––
P5VUSBCT_P0.2115.000–
P5VUSBCT_R0.2115.000–
P5VUSBCT_RTN_DIV0.541––
P5VUSBCT_RTN_DIV_R0.001––
P5VUSBCT_SENSE_DIV_R0.210––
P5VUSBCT_SET_ROL––
P5VUSBCT_SET00.544––
P5VUSBCT_SET10.543––
P5VUSBCT_VBST0.599––
P5VUSBCT_VO0.538––
P5VUSBCX_LL0.1645.000–
P5VUSBCX_N0.164––
P5VUSBCX_P0.164––
P5VUSBCX_R0.1645.000–
P5VUSBCX_RTN_DIV_R0.001––
P5VUSBCX_SENSE_DIV_R0.165––
P12V_SSD_VPP_SW0.40712.000–
P12V_SSD_VPP_SW_L0.40712.000–
P16V0_AGND0.047––
PANEL_FET_EN_DLY0.708––
PANEL_P3V3_EN_D0.754––
PANEL_P5V_EN_D1.046––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.451––
PBUSVSENS_EN_L0.487––
PBUSVSENS_EN_L_DIVOL––
PCC_COMP_OUTOL––
PCC_COMP_OUT_BASEOL––
PCC_POT_LEVELOL––
PCC_POT_LEVEL_DOL––
PCC_POT_LEVEL_ROL––
PCC_POT_REFOL––
PCC_POT_RHOL––
PCC_POT_RLOL––
PCC_POT_WPOL––
PCH_BT_UART_D2R0.445––
PCH_BT_UART_R2D0.417––
PCH_BT_UART_RTS_L0.418––
PCH_CPU_TRIGGER0.537––
PCH_CPU_TRIGGER_R0.514––
PCH_DDPB_CTRLDATA0.779––
PCH_DDPC_CTRLDATA0.778––
PCH_DIFFCLK_BIASREF0.786––
PCH_DISPA_BCLK0.460––
PCH_DISPA_SDI0.358––
PCH_DISPA_SDO0.457––
PCH_DISPA_SDO_R0.463––
PCH_JTAGX0.056––
PCH_PCIE_RCOMPN0.387––
PCH_PCIE_RCOMPP0.390––
PCH_PROCPWRGD0.472––
PCH_SOC_DBELL_L0.474––
PCH_SOC_DFU_STATUS0.537––
PCH_SOC_FORCE_DFU0.475––
PCH_SOC_WDOG0.538––
PCH_SRTCRST_L0.821––
PCH_STRP_TOPBLK_SWP_L0.560––
PCH_SWD_IO0.669––
PCH_SWD_MUX_SEL0.597––
PCIE_WAKE_L0.512––
PDCINVSENS_EN_L_DIVOL––
PLT_RST_L0.353––
PLT_RST_L_BUF0.616––
PM_ALL_GPU_PGOOD0.526––
PM_BATLOW_L0.528––
PM_DSW_PWRGD0.744––
PM_EN_P3V3_G3H0.6003.3000.350R
PM_EN_P3V3_G3H_R0.6003.3000.350R
PM_EN_PVXS50.517––
PM_MEMVTT_EN0.375––
PM_PCH_PWROK0.452––
PM_PCH_SYS_PWROK0.454––
PM_PWRBTN_L0.713––
PM_RSMRST_L0.449––
PM_SLP_S0_L0.461––
PM_SLP_S0S3_L0.507––
PM_SLP_S3_L0.440––
PM_SLP_S4_L0.456––
PM_SLP_S5_L0.484––
PM_SLP_SUS_L0.464––
PM_SYNC0.544––
PM_SYSRST_L0.727––
PM_THRMTRIP_L0.257––
PM_THRMTRIP_L_R0.459––
PMIC_SLAVEADDR0.489––
PMIC_VDCSNS0.001––
PMU_SOC_UWAKE_L0.567––
PMU_TO_SOC_AWAKE_PWRGD0.446––
PMU_TO_SOC_RESET_L0.447––
PMU_TO_SOC_SLEEP1_PWRGD0.448––
PMU_TO_SOC_SYS_ALIVE0.475––
PMU_VDD_RTC0.361––
PMU_VREF0.555––
PP_STOCKHOLM_TVDD0.374––
PP_STOCKHOLM_VMID0.571––
PP0V6_S0_DDRVTT0.136––
PP0V6_S3_MEM_VREFCA_A0.690––
PP0V6_S3_MEM_VREFDQ_A0.751––
PP0V6_S3_MEM_VREFDQ_B0.746––
PP0V6_SLEEP1_BUCK00.3650.600–
PP0V6_SLEEP2_LDO00.383––
PP0V8_SLEEP1_SW10.151––
PP0V8_SLEEP2_BUCK10.2220.800–
PP0V9_TBT_T_CIO0.409––
PP0V9_TBT_T_DP0.339––
PP0V9_TBT_T_LVR0.297––
PP0V9_TBT_T_PCIE0.320––
PP0V9_TBT_T_SVR0.2510.900–
PP0V9_TBT_T_USB0.424––
PP0V9_TBT_X_CIO0.347––
PP0V9_TBT_X_DP0.289––
PP0V9_TBT_X_LVR0.249––
PP0V9_TBT_X_PCIE0.273––
PP0V9_TBT_X_SVR0.2230.900–
PP0V9_TBT_X_USB0.362––
PP1V_PCH_REG_R0.0561.00055.000R
PP1V_S5_PCH_DCPDSW0.328––
PP1V_SUS_PCH_VCCCLK5_F0.0561.00055.300R
PP1V_SUS_PCH_VCCHDAPLL_F0.0561.00055.300R
PP1V_SUS_PCH_VCCUSB2HDAPLL_F0.0561.00055.300R
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.056–55.300R
PP1V0_S0SW0.214––
PP1V0_S30.213––
PP1V0_SSD_CORE0.3381.000–
PP1V0_SSD_CORE_L120.2721.000–
PP1V0_SSD_PLL–1.000–
PP1V0_SUS0.0561.00055.300R
PP1V1_SLEEP1_SW20.367––
PP1V1_SLEEP3_BUCK20.3031.100–
PP1V1_SSD_LVDS0.3571.100–
PP1V1_SSD_PCIE0.3511.100–
PP1V1_UPC_TA_LDO_BMC0.5271.1000.145R
PP1V1_UPC_TB_LDO_BMC0.5281.1000.147R
PP1V1_UPC_XA_LDO_BMC0.5251.1000.145R
PP1V1_UPC_XB_LDO_BMC0.5121.1000.143R
PP1V2_S0SW0.219––
PP1V2_S30.2251.200–
PP1V2_S3_CPUDDR0.221––
PP1V2_S3_REG_R0.2251.200–
PP1V2_S5_SMC_VDDC0.4991.2000.018R
PP1V2_SSD_DRAM0.3031.200–
PP1V2_SSD_DRAM_L120.524––
PP1V5R1V35_GPU_REG_R0.0531.500170.000
PP1V5R1V35_S0_GPU_IC0.231––
PP1V5R1V35_S0_GPU_MEM0.0531.500170.000
PP1V8_ALWAYS_LDO90.398––
PP1V8_AWAKE_SW3C0.350––
PP1V8_GPU0.1881.800–
PP1V8_GPU_TSVDD0.188––
PP1V8_MESA0.556––
PP1V8_MESA_CONN0.617––
PP1V8_S00.3501.800–
PP1V8_S0_GPU0.188––
PP1V8_S0_GPU_LC_IC0.188––
PP1V8_S0_LDO_AUD0.480––
PP1V8_S0_PCH_VCCHDA_F0.3501.800–
PP1V8_S0SW_DFR0.5521.800–
PP1V8_S30.352–0.900R
PP1V8_S3_MEM0.352–0.900R
PP1V8_S40.426––
PP1V8_SLEEP2_LPPLL_FILT0.626––
PP1V8_SLEEP2_SW3A0.425––
PP1V8_SLEEP3_BUCK30.4051.800–
PP1V8_SSD_DRAM0.3971.800–
PP1V8_SSD_DRAM_L120.5791.800–
PP1V8_SSD_FMC0.3661.800–
PP1V8_SSD_LVDS0.4011.800–
PP1V8_SSD_OSC0.3981.800–
PP1V8_SSD_PLL00.579––
PP1V8_SSD_PLL01–1.800–
PP1V8_SSD_PLL10.5791.800–
PP1V8_SSD_PLL20.5791.800–
PP1V8_SSD_PLL30.5791.800–
PP1V8_SSD_PLL230.410––
PP1V8_SUS0.4411.800–
PP1V8_SUS_REG_R0.4351.800–
PP1V8_UPC_TA_LDOA0.5751.8000.194R
PP1V8_UPC_TA_LDOD0.5141.8000.276R
PP1V8_UPC_TB_LDOA0.5721.8000.198R
PP1V8_UPC_TB_LDOD0.5201.8000.280R
PP1V8_UPC_XA_LDOA0.5321.8000.193R
PP1V8_UPC_XA_LDOD0.4941.8000.276R
PP1V8_UPC_XB_LDOA0.5191.8000.180R
PP1V8_UPC_XB_LDOD0.4831.8000.270R
PP1V25_PMICVREF0.480––
PP2V5_ADC1_VREFOL––
PP2V5_ADC2_VREFOL––
PP2V9_SYSCLK0.451––
PP3V0_AWAKE_LDO70.547––
PP3V0_G3H0.453––
PP3V0_MESA0.5923.000–
PP3V0_MESA_CONN0.654––
PP3V0_S5_AVREF_SMC0.5783.0000.311R
PP3V3_G3H0.3673.3000.003R
PP3V3_G3H_REG_R0.3493.300–
PP3V3_PMICLDO0.413––
PP3V3_S00.326––
PP3V3_S0_AUD_F0.345––
PP3V3_S0_CARBON_R–3.300–
PP3V3_S0_DPMUX_UC_R0.325––
PP3V3_S0_GPU0.538––
PP3V3_S0_GPUTHMSNS_R0.418––
PP3V3_S0_LEFT0.355––
PP3V3_S0_TBTTHMSNS_T_R0.392––
PP3V3_S0_TBTTHMSNS_X_R0.401––
PP3V3_S0SW_DFR0.567––
PP3V3_S0SW_LCD0.566––
PP3V3_S0SW_LCD_R0.566––
PP3V3_S3_DPMUX_UC_R0.329––
PP3V3_S40.328––
PP3V3_S4_BT0.328––
PP3V3_S4_MESA_SW0.424––
PP3V3_S4_SOC_PMU0.330––
PP3V3_S4_T1510.424––
PP3V3_S4_TPAD0.320––
PP3V3_S4_WLAN0.328––
PP3V3_S4_WLAN_SW0.351––
PP3V3_S4SW_SNS0.569––
PP3V3_S4SW_SNS_FET_R0.542––
PP3V3_S50.3903.300–
PP3V3_S5_POLARIS0.379––
PP3V3_S5_SMC_VDDA0.349––
PP3V3_S5_T1390.383––
PP3V3_S5_TBT_T_SW0.478––
PP3V3_S5_TBT_X_SW0.464––
PP3V3_SSD_ISNS_R0.402––
PP3V3_SSD_LIM0.402––
PP3V3_SSD_NAND0.409––
PP3V3_SSD_PMIC_AVIN0.402––
PP3V3_SUS0.365––
PP3V3_TBT_T_ANA_PCIE0.532––
PP3V3_TBT_T_ANA_USB20.517––
PP3V3_TBT_T_F0.3263.300–
PP3V3_TBT_T_LC0.554––
PP3V3_TBT_T_S00.3263.300–
PP3V3_TBT_X_ANA_PCIE0.511––
PP3V3_TBT_X_ANA_USB20.486––
PP3V3_TBT_X_F0.3553.300–
PP3V3_TBT_X_LC0.510––
PP3V3_TBT_X_S00.3553.300–
PP3V3_UPC_TA_LDO0.5303.3000.036R
PP3V3_UPC_TB_LDO0.5473.3000.037R
PP3V3_UPC_XA_LDO0.5123.3000.036R
PP3V3_UPC_XB_LDO0.5133.3000.035R
PP3V3_VREF_PCCOL––
PP5V_COREVR_VCC0.425––
PP5V_EADC1_AVDDOL––
PP5V_EADC2_AVDDOL––
PP5V_PMICLDO0.457––
PP5V_PMICLDO_R0.458––
PP5V_S00.421––
PP5V_S0_ALSCAM_F0.421––
PP5V_S0_BKLT_A0.412––
PP5V_S0_BKLT_DOL––
PP5V_S0_FAN_CONN0.411––
PP5V_S0_GFXIMVP_VDD0.412––
PP5V_S0_GFXIMVP_VDDP0.411––
PP5V_S0_GPU_OPAMPOL––
PP5V_S0_GPUFETOL––
PP5V_S0_KBD0.432––
PP5V_S0_T1390.412––
PP5V_S0GPU_P1V35_GPU0.413––
PP5V_S0SW_LCD0.568––
PP5V_S40.4255.000–
PP5V_S4_ISNS_DOL––
PP5V_S4_T_USBC0.2115.000–
PP5V_S4_TPAD_CONN0.421––
PP5V_S4_X_USBC0.1645.000–
PP5V_S50.473––
PP5V_USBCT_VCC0.427––
PP5V_USBCX_VCC0.428––
PP5V_VREF_PCCOL––
PP12V_SSD_VPP0.455––
PP16V0_MESA0.743––
PP16V0_MESA_CONN0.655––
PP20V_USBC_TA_VBUS0.15520.0000.001R
PP20V_USBC_TA_VBUS_CONN0.15520.000–
PP20V_USBC_TA_VBUS_F0.15520.0000.001R
PP20V_USBC_TB_VBUS0.15520.0000.001R
PP20V_USBC_TB_VBUS_CONN0.17020.000–
PP20V_USBC_TB_VBUS_F0.15520.0000.001R
PP20V_USBC_XA_VBUS0.1555.0000.001R
PP20V_USBC_XA_VBUS_CONN0.15520.000–
PP20V_USBC_XA_VBUS_F0.1555.0000.001R
PP20V_USBC_XB_VBUS0.15520.0000.001R
PP20V_USBC_XB_VBUS_CONN0.15520.000–
PP20V_USBC_XB_VBUS_F0.1555.0000.001R
PPBUS_G3H0.45013.1000.115R
PPBUS_G3H_R0.428––
PPBUS_HS_CPU0.45013.1000.115R
PPBUS_HS_GPU0.45013.1000.115R
PPBUS_HS_OTH3V30.449––
PPBUS_HS_OTH5V0.450––
PPBUS_PMIC0.449––
PPBUS_S4_HS_TPAD0.45012.600–
PPDCIN_G3H0.17020.000156.000R
PPDCIN_G3H_CHGR0.53920.000–
PPDCIN_G3H_CHGR_R0.538––
PPDCPRTC_PCH0.684––
PPSVDD_STOCKHOLM0.355––
PPVBAT_G3H_CHGR_R0.45013.1000.115R
PPVBAT_G3H_CHGR_REG0.45013.1000.115R
PPVBAT_G3H_CONN0.639––
PPVCC_CPU_PH10.0031.5001.520R
PPVCC_CPU_PH20.0031.5003.000R
PPVCC_CPU_PH30.0031.5001.520R
PPVCC_S0_CPU0.0031.5001.520R
PPVCCGT_CPU_PH10.0051.5004.800R
PPVCCGT_CPU_PH20.0051.5002.600R
PPVCCGT_S0_CPU0.0051.5002.600R
PPVCCIO_S0_CPU0.0450.95045.000R
PPVCCSA_CPU_R0.0141.1507.690R
PPVCCSA_S0_CPU0.0141.1507.690R
PPVCORE_S0_GFX_PH10.0031.1002.510R
PPVCORE_S0_GFX_PH20.0031.1002.510R
PPVCORE_S0_GPU0.0031.1002.510R
PPVDD_STOCKHOLM0.320––
PPVDDCI_S0_GPU0.0290.90028.000R
PPVIN_G3H_P3V3G3H0.545––
PPVIN_S0_CPUVR_VIN0.457––
PPVIN_S0_GFXIMVP_VIN0.448––
PPVIN_S0GPU_1V8_RC0.456––
PPVIN_S0SW_LCDBKLT0.87913.100–
PPVIN_S0SW_LCDBKLT_FET0.45013.1000.115R
PPVIN_S0SW_LCDBKLT_R0.45013.1000.115R
PPVIN_S4_TPAD_FUSE0.45012.600–
PPVIN_SUS_VR5_R0.449––
PPVIN_SW_LCDBKLT_SW0.87913.100–
PPVOUT_S0_LCDBKLT1.22859.000–
PROG1_CPUCOREVR0.626––
PROG2_CPUCOREVR0.622––
PROG3_CPUCOREVR0.625––
PROG4_CPUCOREVR0.627––
PVCCCGT_PH1_AGND0.004––
PVCCCORE_PH3_VCC0.413––
PVCCIO_PGOOD0.472––
PVCCIO_PHASE0.0450.95045.000R
PVCCIO_VBST_R0.588––
PVDDCI_PGOOD0.573––
PVTT_FB0.146––
REG_BOOT_GPU_VDDCI_RC0.491––
REG_GPU_VDDCI_COMP0.597––
REG_GPU_VDDCI_FB0.490––
REG_GPU_VDDCI_FB_ROL––
REG_GPU_VDDCI_VSEN_COL––
REG_GPU_VDDCI_VSUMN0.029–28.000R
REG_GPU_VDDCI_VSUMP0.029–28.000R
REG_PHASE_1V8GPU0.1881.800–
RTC_RESET_L0.807––
S5_PWRGD0.497––
SA_ISUMN_R1.027––
SEP_I2C_SCL0.471––
SEP_I2C_SDA0.469––
SMBUS_PCH_CLK0.759––
SMBUS_PCH_DATA0.760––
SMBUS_SMC_0_S0_SCL0.741––
SMBUS_SMC_0_S0_SDA0.750––
SMBUS_SMC_1_S0_SCL0.576––
SMBUS_SMC_1_S0_SDA0.570––
SMBUS_SMC_2_S4_SCL0.530––
SMBUS_SMC_2_S4_SDA0.530––
SMBUS_SMC_3_SCL0.520––
SMBUS_SMC_3_SDA0.504––
SMBUS_SMC_4_G3H_SCL0.6703.3000.004R
SMBUS_SMC_4_G3H_SDA0.6703.3000.021R
SMBUS_SMC_5_G3_SCL0.437––
SMBUS_SMC_5_G3_SDA0.420––
SMC_4FINGERS_RST0.614––
SMC_ACTUATOR_DISABLE_L0.737––
SMC_ADAPTER_EN0.735––
SMC_BC_ACOK0.608––
SMC_BT_PWR_EN0.716––
SMC_CHGR_INT_L0.607––
SMC_CLK12M_EN0.476––
SMC_CLK32K0.605––
SMC_CPU_HI_ISENSE0.730––
SMC_CPU_IMON_ISENSE0.733––
SMC_CPUDDR_ISENSE0.751––
SMC_CPUGT_IMON_ISENSE0.738––
SMC_CPUGT_ISENSE0.732––
SMC_CPUSA_ISENSE0.731––
SMC_CPUSA_VSENSE0.724––
SMC_DCIN_VSENSE0.726––
SMC_DDR1V2_ISENSE0.733––
SMC_DEBUGPRT_RX_L0.718––
SMC_DEBUGPRT_TX_L0.717––
SMC_DEBUGPRT2_R_RX0.735––
SMC_DEBUGPRT2_R_TX0.747––
SMC_DELAYED_PWRGD0.735––
SMC_DEV_SUPPLY_R_L0.738––
SMC_FAN_0_CTL0.748––
SMC_FAN_0_TACH0.735––
SMC_FAN_1_CTL0.750––
SMC_FAN_1_TACH0.749––
SMC_GFX_OVERTEMP0.614––
SMC_GFX_PWR_LEVEL_L0.640––
SMC_GFX_SELF_THROTTLE0.643––
SMC_GPU_HS_ISENSE0.731––
SMC_GPU_VDDCI_ISENSE0.699––
SMC_GPU_VDDCI_VSENSE0.725––
SMC_LID0.4463.400–
SMC_LID_LEFT0.701––
SMC_LID_LEFT_R0.701––
SMC_LID_R0.694––
SMC_LID_RIGHT0.463––
SMC_LRESET_L0.748––
SMC_LSOC_RST_L0.737––
SMC_ONOFF_L0.717––
SMC_OOB1_D2R_L0.736––
SMC_OOB1_R2D_L0.736––
SMC_PBUS_VSENSE0.726––
SMC_PCH_SUSACK_L0.740––
SMC_PCH_SUSWARN_L0.570––
SMC_PECI_L0.724––
SMC_PM_G2_EN0.505––
SMC_PME_S4_DARK_L0.536––
SMC_PME_S4_WAKE_L0.736––
SMC_PMIC_INT_L0.475––
SMC_PROCHOT0.753––
SMC_PROCHOT_L0.562––
SMC_RESET_L0.709––
SMC_RST_L0.6153.3000.340R
SMC_RUNTIME_SCI_L0.583––
SMC_SENSOR_ALERT_L0.545––
SMC_SENSOR_PWR_EN0.596––
SMC_SOCPMU_RESET0.545––
SMC_TCK0.735––
SMC_TDI0.735––
SMC_TDO0.735––
SMC_THRMTRIP0.750––
SMC_THRMTRIP_L0.361––
SMC_TMS0.736––
SMC_TOPBLK_SWP_L0.674––
SMC_TPAD_ISENSEOL––
SMC_USBC_INT_L0.647––
SMC_VCCIO_CPU_DIV20.751––
SMC_VIBE_L0.748––
SMC_WAKE_L0.734––
SMC_WAKE_SCI_L0.568––
SMC_WIFI_PWR_EN0.530––
SML_PCH_0_CLK0.787––
SOC_AWAKE_REQ0.467––
SOC_CLK_32K0.439––
SOC_JTAG_SEL0.474––
SOC_PANIC_L0.519––
SOC_PMU_BUCK0_LX0.3650.600–
SOC_PMU_BUCK1_LX0.2220.800–
SOC_PMU_BUCK2_LX0.3031.100–
SOC_PMU_BUCK3_LX0.4051.800–
SOC_PMU_I2C_SCL0.468––
SOC_PMU_I2C_SDA0.468––
SOC_ROM_SPI_CLK_R0.446––
SOC_ROM_SPI_MOSI_R0.467––
SOC_SLEEP1_REQ0.467––
SOC_SPI_BOOT_STATUS0.477––
SOC_SWCLK0.475––
SOC_SWCLK_DBG0.508––
SOC_SWD_CLK0.674––
SOC_SWDIO0.475––
SOC_SWDIO_DBG0.508––
SOC_TO_STOCKHOLM_DEV_WAKE0.476––
SOC_TO_STOCKHOLM_DWLD_REQ0.476––
SOC_UART_D2R0.515––
SOC_UART_R2D0.516––
SOC_USB_VBUS0.766––
SPI_ALT_CLK0.709––
SPI_ALT_CS_L0.667––
SPI_ALT_IO0_MOSI0.597––
SPI_ALT_IO1_MISO0.569––
SPI_ALT_IO2_WP_L0.564––
SPI_ALT_IO3_HOLD_L0.588––
SPI_DESCRIPTOR_OVERRIDE1.732––
SPI_DESCRIPTOR_OVERRIDE_L0.752––
SPI_IO<2>0.556––
SPI_MLB_CLK0.696––
SPI_MLB_CS_L0.665––
SPI_MLB_IO0_MOSI0.700––
SPI_MLB_IO1_MISO0.621––
SPI_MLB_IO2_WP_L0.586––
SPI_MLB_IO3_HOLD_L0.584––
SPI_MLBROM_CS_L0.649––
SPI_MOSI_R0.725––
SPI_MOSI_R_CONN0.988––
SPIROM_USE_MLB0.700––
SPKR_ID00.757––
SPKR_ID0_NC0.577––
SPKRAMP_R_SCLK0.358––
SPKRAMP_TL_OUT_NEG0.613––
SPKRAMP_TL_OUT_POS0.613––
SPKRAMP_TR_OUT_NEG0.598––
SPKRAMP_TR_OUT_POS0.599––
SPKRAMP_WL_LRCLK0.376––
SPKRAMP_WL_OUT_NEG0.613––
SPKRAMP_WL_OUT_POS0.613––
SPKRAMP_WL_SCLK0.376––
SPKRAMP_WL_SDIN0.376––
SPKRAMP_WR_LRCLK0.358––
SPKRAMP_WR_OUT_NEG0.599––
SPKRAMP_WR_OUT_POS0.599––
SPKRAMP_WR_SCLK0.358––
SPKRAMP_WR_SDIN0.358––
SPKRCONN_TL_OUT_NEG0.613––
SPKRCONN_TL_OUT_POS0.613––
SPKRCONN_TR_OUT_NEG0.598––
SPKRCONN_TR_OUT_POS0.599––
SPKRCONN_WL_OUT_NEG0.613––
SPKRCONN_WL_OUT_POS0.613––
SPKRCONN_WR_OUT_NEG0.599––
SPKRCONN_WR_OUT_POS0.599––
SPROM_CLK0.554––
SPROM_CS0.567––
SPROM_DIN0.588––
SPROM_DOUT0.567––
SSD_3V3_SS0.755––
SSD_BOOT_L0.432––
SSD_BOOT_LB_L0.458––
SSD_CLKREQ_L0.767––
SSD_CLKREQ_LB_L0.769––
SSD_DEBUG_I2C_CLK0.673––
SSD_DEBUG_I2C_CLK_CONN0.683––
SSD_DEBUG_I2C_DAT0.672––
SSD_DEBUG_I2C_DAT_CONN0.685––
SSD_DEBUG_MUX_OE0.564––
SSD_DEBUGI2C_SEL_PCH0.548––
SSD_FVREF00.485––
SSD_GP00.008––
SSD_GP80.010––
SSD_GP90.775––
SSD_GP100.775––
SSD_GP120.495––
SSD_I2C_CLK0.547––
SSD_I2C_DAT0.550––
SSD_NAND_FA_RDY0.765––
SSD_NAND_FA_ZQ0.251––
SSD_NAND_FD_RDY0.660––
SSD_NAND_FE_RDY0.621––
SSD_NAND_FF_RDY0.578––
SSD_NAND_FG_RDY0.583––
SSD_P3V3_NAND_CT0.757––
SSD_PGOOD_L0.559––
SSD_PMIC_LDO0.497––
SSD_PWR_EN0.500––
SSD_PWR_LB_EN0.499––
SSD_PWRCON00.459––
SSD_PWRCON1_R00.515––
SSD_PWRCON1_R10.515––
SSD_PWRCON1_R20.516––
SSD_PWRCON20.450––
SSD_PWRCON30.455––
SSD_RESET_B_L0.559––
SSD_RESET_L0.449––
SSD_RESET_LB_L0.469––
SSD_SVREF10.765––
SSD_SZQ0.250––
SSD_VREF_CA0.790––
SSD_VREF_DQ0.789––
SSD_ZQ00.250––
SYS_DETECT_LOL––
SYSCLK_CLK32K_CAMERA_BT_AP0.424––
TBA_AUX_DET0.6215.0000.195R
TBA_BGATE0.634––
TBA_BOOT1_RC0.575––
TBA_BOOT2_RC0.571––
TBA_COMP0.619––
TBA_CSI_N0.54020.000–
TBA_CSI_P0.54020.000–
TBA_CSI_R_N0.54020.000–
TBA_CSI_R_P0.54020.000–
TBA_CSO_N0.45013.100–
TBA_CSO_P0.45013.100–
TBA_CSO_R_N0.45013.1000.115R
TBA_CSO_R_P0.45013.1000.115R
TBA_GATE_Q10.864––
TBA_GATE_Q20.476––
TBA_GATE_Q30.477––
TBA_GATE_Q40.865––
TBA_LX10.408––
TBA_LX20.409––
TBA_PHASE10.35713,1000.120R
TBA_PHASE20.35713,1000.120R
TBA_VDDA0.4515.0000.030R
TBA_VDDP0.449––
TBT_POC_RESET0.575––
TBT_T_CIO_PLUG_EVENT_L0.596––
TBT_T_CIO_PWR_EN0.588––
TBT_T_CLKREQ_L0.599––
TBT_T_FORCE_PWR0.598––
TBT_T_HDMI_DDC_CLK0.602––
TBT_T_HDMI_DDC_DATA0.602––
TBT_T_PCI_RESET_L0.546––
TBT_T_ROM_HOLD_L0.727––
TBT_T_ROM_WP_L0.594––
TBT_T_SPI_CLK0.574––
TBT_T_SPI_CLK_DBG0.673––
TBT_T_SPI_CS_L0.602––
TBT_T_SPI_MISO0.622––
TBT_T_TMU_CLK_IN0.559––
TBT_T_TMU_CLK_OUT0.558––
TBT_T_USB_PWR_EN0.590––
TBT_TB_LSTX0.599––
TBT_W_CLKREQ_L0.789––
TBT_W_PCI_RESET_L0.788––
TBT_X_CIO_PLUG_EVENT_L0.569––
TBT_X_CIO_PWR_EN0.566––
TBT_X_CLKREQ_L0.575––
TBT_X_CLKREQ_L_R0.775––
TBT_X_FORCE_PWR0.575––
TBT_X_HDMI_DDC_CLK0.573––
TBT_X_HDMI_DDC_DATA0.575––
TBT_X_PCI_RESET_L0.533––
TBT_X_PCIE_BIAS0.787––
TBT_X_RBIAS0.786––
TBT_X_ROM_HOLD_L0.709––
TBT_X_ROM_WP_L0.569––
TBT_X_RSENSE0.001––
TBT_X_SPI_CLK0.558––
TBT_X_SPI_CS_L0.580––
TBT_X_SPI_MOSI0.584––
TBT_X_TEST_EN0.101––
TBT_X_TEST_PWR_GOOD0.100––
TBT_X_TMU_CLK_IN0.556––
TBT_X_TMU_CLK_OUT0.552––
TBT_X_USB_PWR_EN0.567––
TBT_XB_LSRX0.575––
TBT_XB_LSTX0.575––
TBTTHMSNS_T_ALERT_L0.582––
TBTTHMSNS_T_THM_L0.602––
TBTTHMSNS_X_ALERT_L0.533––
TBTTHMSNS_X_D1_N0.001––
TBTTHMSNS_X_THM_L0.592––
TP_BMON_IOUTOL––
TP_CARBON_INT1OL––
TP_CARBON_INT2OL––
TP_DPA_IG_HPD0.652––
TP_DPMUX_UC_P600.651––
TP_DPMUX_UC_P610.651––
TP_EG_BKLT_PWM0.358––
TP_J3300_P2OL––
TP_J3300_P56OL––
TP_JB500_P2OL––
TP_JB500_P56OL––
TP_PVDDCI_GPU_EN0.644––
TP_Q3100_DRAIN0.631––
TP_Q3200_DRAIN0.628––
TP_QB300_DRAIN0.640––
TP_QB400_DRAIN0.639––
TP_SOC_CLKOUT0.478––
TP_SOC_JTAG_TDI0.475––
TP_SOC_JTAG_TDO0.475––
TP_SOC_JTAG_TRST_L0.477––
TP_SOC_TST_CKOUT0.476––
TP_SYS_ONEWIRE0.753––
TP_UPC_TA_DBG_UART_RX0.791––
TP_UPC_TA_DBG_UART_TX0.792––
TP_UPC_TA_SWD_CLK0.751––
TP_UPC_TA_SWD_DATA0.751––
TP_UPC_TB_DBG_UART_RX0.800––
TP_UPC_TB_DBG_UART_TX0.800––
TP_UPC_TB_SWD_CLK0.767––
TP_UPC_TB_SWD_DATA0.773––
TP_UPC_XA_SWD_CLK0.749––
TP_UPC_XA_SWD_DATA0.748––
TP_UPC_XB_DBG_UART_RX0.773––
TP_UPC_XB_DBG_UART_TX0.775––
TP_UPC_XB_SWD_CLK0.749––
TP_UPC_XB_SWD_DATA0.749––
TPAD_SPI_CLK0.805––
TPAD_SPI_CLK_CONN0.633––
TPAD_SPI_CS_L0.642––
TPAD_SPI_CS_L_CONN0.990––
TPAD_SPI_IF_EN0.518––
TPAD_SPI_IF_EN_CONN0.674––
TPAD_SPI_INT_L_CONN0.673––
TPAD_SPI_MISO0.589––
TPAD_SPI_MISO_R0.777––
TPAD_SPI_MOSI0.805––
TRY_WRONG_INPUT–25.000–
UPC_T_5V_EN0.543––
UPC_T_SPI_CLK0.600––
UPC_T_SPI_CS_L0.620––
UPC_T_SPI_MISO0.596––
UPC_T_SPI_MOSI0.621––
UPC_TA_DBG20.777––
UPC_TA_DBG30.818––
UPC_TA_DBG40.820––
UPC_TA_GATE10.676–0.447R
UPC_TA_GATE20.667–0.415R
UPC_TA_R_OSC0.535––
UPC_TA_SPI_MISO0.636––
UPC_TA_SS0.534––
UPC_TB_GATE10.675–0.444R
UPC_TB_GATE20.666––
UPC_TB_R_OSC0.570––
UPC_X_5V_EN0.543––
UPC_X_SPI_CLK0.555––
UPC_X_SPI_CS_L0.569––
UPC_X_SPI_MISO0.571––
UPC_XA_DBG_UART_RX0.773––
UPC_XA_DBG_UART_TX0.775––
UPC_XA_GATE10.6605.0000.440R
UPC_XA_GATE20.6505.0000.415R
UPC_XA_HPD_RX0.001––
UPC_XA_R_OSC0.533––
UPC_XA_UART_RX0.765––
UPC_XB_GATE10.660–0.445R
UPC_XB_GATE20.651–0.419R
UPC_XB_R_OSC0.517––
UPC_XB_SS0.519––
USB_TEST_N0.612––
USB_TEST_P0.604––
USB2_COMP0.115––
USB2_ID0.770––
USB2_VBUSSENSE0.772––
USB3_TEST_D2R_N0.380––
USB3_TEST_D2R_P0.374––
USB3_TEST_R2D_N0.366––
USB3_TEST_R2D_P0.367––
USBC_T_RESET_L0.736––
USBC_T_RESET_L_R0.563––
USBC_TA_CC10.6110.6000.338R
USBC_TA_CC20.6280.6000.338R
USBC_TA_SBU10.865––
USBC_TA_SBU20.868––
USBC_TB_CC10.6300.6000.342R
USBC_TB_CC20.6330.6000.342R
USBC_TB_SBU10.859––
USBC_TB_SBU20.860––
USBC_X_RESET_L0.736––
USBC_XA_CC10.6070.6000.338R
USBC_XA_CC20.6100.6000.338R
USBC_XA_D2R_N<1>0.327––
USBC_XA_D2R_N<2>0.325––
USBC_XA_D2R_P<1>0.327––
USBC_XA_D2R_P<2>0.325––
USBC_XA_R2D_C_N<2>0.350––
USBC_XA_R2D_C_P<2>0.350––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_SBU10.903––
USBC_XA_SBU20.904––
USBC_XA_USB_DBG_TOP_N0.858––
USBC_XA_USB_DBG_TOP_POL––
USBC_XB_CC10.6140.6000.345R
USBC_XB_CC20.6160.6000.345R
USBC_XB_D2R_N<1>0.570––
USBC_XB_D2R_P<1>0.570––
USBC_XB_R2D_N<1>OL––
USBC_XB_R2D_P<1>OL––
USBC_XB_SBU10.864––
USBC_XB_SBU20.862––
VR_PHASE_GPU_VDDCI0.0290.90028.000R
VR0V9_IND_TBT_T0.2510.900–
VR0V9_IND_TBT_X0.2230.900–
VREF_AMP_TR0.580––
VREF_AMP_WL0.588––
VRVDDCI_R0.0290.90028.000R
WIFI_SROM_ORGOL––
WLAN_1P2V_EN0.580––
WLAN_JTAG_SEL0.598––
WLAN_JTAG_TCK0.554––
WLAN_JTAG_TDI0.579––
WLAN_JTAG_TMS0.590––
WLAN_JTAG_TRST_L0.565––
WLAN_UART_RX0.576––
WLAN_UART_TX0.553––
XDP_BPM_L<0>0.285––
XDP_BPM_L<1>0.285––
XDP_BPM_L<2>0.283––
XDP_BPM_L<3>0.285––
XDP_CPU_PRDY_L0.262––
XDP_CPU_PREQ_L0.286––
XDP_CPU_PWRBTN_L0.720––
XDP_CPU_TCK0.052–55.200R
XDP_CPU_TDI0.241––
XDP_CPU_TDO0.219––
XDP_CPU_TMS0.242––
XDP_CPU_TRST_L0.289––
XDP_DBRESET_L0.716––
XDP_PCH_OBSDATA_A00.841––
XDP_PCH_OBSDATA_A10.866––
XDP_PCH_OBSDATA_A20.868––
XDP_PCH_OBSDATA_A30.866––
XDP_PCH_OBSDATA_B00.865––
XDP_PCH_OBSDATA_B10.865––
XDP_PCH_OBSDATA_B20.842––
XDP_PCH_OBSDATA_B30.842––
XDP_PCH_OBSDATA_C00.832––
XDP_PCH_OBSDATA_C10.805––
XDP_PCH_OBSDATA_C20.830––
XDP_PCH_OBSDATA_C30.833––
XDP_PCH_OBSDATA_D00.875––
XDP_PCH_OBSDATA_D10.836––
XDP_PCH_OBSDATA_D20.841––
XDP_PCH_OBSDATA_D30.841––
XDP_PCH_OBSFN_C00.863––
XDP_PCH_OBSFN_C10.841––
XDP_PCH_TCK0.449––
XDP_PCH_TDI0.239––
XDP_PCH_TDO0.221––
XDP_PCH_TMS0.288––
XDP_PCH_TRST_L0.286––
XDP_PM_RSMRST_L1.472––
XDP_PRESENT_CPU1.284––
XDP_PRESENT_L0.521––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00281?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00281: diode 0.450, voltage 13.100, resistance to ground 0.115R. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00281?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00281: diode 0.367, voltage 3.300, resistance to ground 0.003R. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00281?

OpenBoardData's known-good values for PP5V_S5 on the 820-00281: diode 0.473. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00281 board?

Open your own 820-00281 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License