Apple laptop board · OpenBoardData

820-00850 known-good readings

Known-good readings for the Apple laptop board 820-00850: 1,796 nets, including 95 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 95 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00850.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 95 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 45

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.3301.800–
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V always-on rail; the G3S part of the name indicates it belongs to the always-on startup stage (from the name). Known-good readings are diode 0.330 and voltage 1.800. With the board unpowered, measure diode mode from the rail to ground; then power up and check for 1.800 V. A reading far from known-good usually points to a short or a missing supply on that rail, but one reading alone doesn't confirm a bad part. No known-good resistance value is recorded here.

PP1V8_G3S_WLANBT_VDDIO0.336––
AI: what PP1V8_G3S_WLANBT_VDDIO is and how to check it
  • What it is: From the name, a 1.8 V always-on (G3S) I/O supply for the WLAN/Bluetooth section. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.336 to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage at the same point.
  • If it's far off: a low diode reading suggests a short or leaky part on the rail; a correct diode but no voltage points upstream at the regulator or its enable. Confirm with a second measurement before replacing anything.
PP3V_G3H_RTC0.4473.000–
AI: what PP3V_G3H_RTC is and how to check it

PP3V_G3H_RTC is the always-on 3.3 V RTC rail; the "G3H" in the name means it stays up whenever power is connected, before the main rails come on. Known-good readings here are diode 0.447 and voltage 3.000, with no condition noted. With the board unpowered, measure diode mode from the rail to ground; then power it and check the voltage. A diode reading far from 0.447 usually points to a short or a leaky part on that rail, but one reading isn't proof — no known-good resistance value is listed here, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3H0.4303.300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the 3.3 V always-on rail; the "G3H" part of the name indicates it should be present as soon as the board has power, before the main power sequence.

Known-good readings for this board (community guide, from the readings archive):

  • Diode mode to ground: 0.430
  • Voltage with power applied: 3.300 V

To check it, power off and measure diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far from 0.430 usually points to a short or a damaged component on that rail; a voltage well below 3.300 V with a normal diode reading points more toward the rail not being enabled or its source not coming up. No known-good resistance reading is listed for this rail.

PP3V3_G3H_DFR0.439––
AI: what PP3V3_G3H_DFR is and how to check it

PP3V3_G3H_DFR is a 3.3 V always-on rail, judged from the G3H part of its name (general naming convention, not from this board's data). The only known-good reading here is a diode value of 0.439; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from PP3V3_G3H_DFR to ground and compare with 0.439.
  • Then power the board and check the voltage on the rail; the data gives no expected figure, so compare against a known-good board or the same rail on a matching unit.
  • A diode reading far below 0.439 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. One reading alone doesn't confirm a bad part, so check the voltage next before replacing anything.
PP3V3_G3H_DFUMUXOL––
AI: what PP3V3_G3H_DFUMUX is and how to check it

PP3V3_G3H_DFUMUX is a 3.3 V rail; the "G3H" part of the name indicates it is always-on (from the name), and "DFUMUX" suggests it feeds the debug/USB multiplexing side (general interpretation, not from this board's data).

  • Known-good: diode reading to ground is OL (open, no short) with the board unpowered. No known-good voltage reading here.
  • Check it in diode mode to ground with power off, then measure the voltage with power applied and compare against a matching rail or a known-good board.
  • A diode reading far below OL usually points to a short or leaky part on that rail; a missing voltage with a good diode reading points upstream to its source.
PP3V3_G3H_MESA_SW0.403––
AI: what PP3V3_G3H_MESA_SW is and how to check it

PP3V3_G3H_MESA_SW is a 3.3 V always-on rail; the G3H part of the name (from the name) marks it as a startup-stage supply, and MESA_SW suggests it feeds the MESA section through a switch. The only known-good figure here is a diode reading of 0.403 to ground; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.403 usually points to a short or a damaged part on that net, but one reading isn't proof, so confirm with a voltage check before replacing anything.

PP3V3_G3H_PMU_VDDMAIN0.4363.300–
AI: what PP3V3_G3H_PMU_VDDMAIN is and how to check it

PP3V3_G3H_PMU_VDDMAIN is a 3.3 V rail feeding the PMU's main supply; the G3H part of the name indicates it is an always-on rail (from the name). Known-good readings here are diode 0.436 and voltage 3.300, community-contributed and only a guide. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.436 suggests a short or leaky load on the rail; a voltage well off 3.300 points to the rail not coming up or being pulled down. No known-good resistance reading exists for this rail.

PP3V3_G3H_PMU_VINRTC_R0.4023.300–
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check it

PP3V3_G3H_PMU_VINRTC_R — reference note

  • What it is: a 3.3 V always-on rail feeding the PMU's RTC/keep-alive input. The "G3H" in the name indicates it belongs to the always-on startup stage; the rest of the name is from the net name itself.
  • Known-good readings (community guide): diode 0.402 in diode mode, and 3.300 V with the board powered. These are contributed values and vary with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: a diode reading well below 0.402 suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points upstream, to whatever generates this rail rather than the rail itself. No known-good resistance reading exists for this net, so compare against a matching always-on rail or a known-good board.
PP3V3_G3H_RTC0.3273.300–
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC is the always-on 3.3 V rail that feeds the RTC circuit; the "G3H" part of the name indicates it is an always-on rail (from the name). Known-good readings here are diode 0.327 to ground and 3.300 V with power applied. Check it unpowered in diode mode from PP3V3_G3H_RTC to ground, then power the board and measure the voltage, for example at L6900 pin 1 where the 3V3 reading is noted. A diode reading far from 0.327 suggests a short or leak on the rail; a voltage well below 3.300 V points to the rail not coming up or being loaded down. No known-good resistance reading is listed for this rail.

PP3V3_G3H_RTC_ISOL0.383.300–
AI: what PP3V3_G3H_RTC_ISOL is and how to check it

PP3V3_G3H_RTC_ISOL — the name indicates a 3.3 V rail, always-on (G3H), feeding the RTC section, with "ISOL" suggesting it is isolated or separately derived from the main 3V3 G3H rail. This is from the name only; the parts on it aren't known here.

  • Known-good from the archive: diode 0.38 to ground, voltage 3.300.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A voltage well below 3.3 V or a diode reading far from 0.38 points to a short or a load pulling the rail down; a high or open diode reading suggests a broken feed.
  • No known-good resistance reading is recorded for this rail.
PP3V3_G3H_RTC_MESA0.4033.300–
AI: what PP3V3_G3H_RTC_MESA is and how to check it
  • What it is: PP3V3_G3H_RTC_MESA is a 3.3 V always-on rail; the G3H part of the name indicates it should be present whenever power is connected, before the board is switched on. That reading is from the name, not from a schematic.
  • Known-good readings (community guide): diode 0.403 to ground, and 3.300 V with power applied.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a correct diode reading with no voltage points upstream, toward whatever feeds the rail. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PP3V3_G3H_RTC_REG_R0.3993.300–
AI: what PP3V3_G3H_RTC_REG_R is and how to check it

PP3V3_G3H_RTC_REG_R is a 3.3 V always-on rail feeding the RTC/regulator area; the G3H part of the name indicates it comes up in the always-on startup stage (from the name). Known-good readings here are diode 0.399 and voltage 3.300, community-contributed so treat them as a guide. With the board unpowered, measure diode mode from the rail to ground and compare with 0.399; then power up and check for about 3.300 V. A diode reading far below known-good suggests a short or leaky part on the rail, while a missing or low voltage with a normal diode reading points upstream at its source; no known-good resistance reading is listed for this rail.

PP3V3_G3H_SSD00.3983.300–
AI: what PP3V3_G3H_SSD0 is and how to check it

PP3V3_G3H_SSD0 is a 3.3 V always-on rail feeding the SSD section; the "G3H" part of the name indicates it should be present whenever the board has power, and "SSD0" points to the SSD supply. Known-good readings for this board are diode 0.398 and voltage 3.300. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 3.3 V with a low diode reading suggests a short or heavy load on the rail; a correct diode reading with no voltage points upstream at the source. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.

PP3V3_G3HSW_DFR0.55––
AI: what PP3V3_G3HSW_DFR is and how to check it
  • What it is: PP3V3_G3HSW_DFR is a 3.3 V rail in the G3H (always-on) startup group, judged from the name; the "DFR" suffix suggests it feeds a deferred/display-related load, though that part is inference, not board data.
  • Known-good reading: diode mode 0.55 to ground. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage, expecting about 3.3 V.
  • If it's off: a diode reading far below 0.55 suggests a short or a leaky load on the rail; far above suggests an open path. A single reading isn't proof of a bad part — compare against a matching rail or a known-good board before replacing anything.
PP3V3_G3S0.3003.300–
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is the 3.3 V "G3S" rail; the G3S part of the name indicates it belongs to the always-on startup stage, so it should be present whenever the board has power. From the readings archive, the known-good values are diode 0.300 and voltage 3.300; treat these as a guide, since community readings vary with board state.

  • Check it unpowered: diode mode from PP3V3_G3S to ground, expecting about 0.300.
  • Then power the board and measure the voltage, expecting about 3.300 V.

The archive has no resistance reading for this rail, so there is no known-good value of that kind. A diode reading far below 0.300 suggests a short or a leaky part on the rail; a correct diode reading with missing voltage points upstream, toward whatever feeds the rail. These are general interpretations, not confirmed causes.

PP3V3_G3S_KBD0.297––
AI: what PP3V3_G3S_KBD is and how to check it
  • What it is: PP3V3_G3S_KBD is a 3.3 V rail for the keyboard, from its name. The G3S part of the name suggests it comes up in the always-on/startup stage rather than being switched later, but that's general naming convention, not confirmed for this board.
  • Known-good reading: diode mode to ground is 0.297. That's the only known-good value recorded here; there's no known-good voltage or resistance for this rail.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage at the rail.
  • If it's far off: a diode reading well below 0.297 suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken connection or missing part. A missing 3.3 V with power on points upstream in the G3S power sequence. One reading alone doesn't prove a part bad.
PP3V3_G3S_TPAD0.3003.300–
AI: what PP3V3_G3S_TPAD is and how to check it

PP3V3_G3S_TPAD — a 3.3 V rail for the trackpad, in the G3S (always-on) startup stage, judging from the name.

  • Known-good: diode 0.300, voltage 3.300. Community readings, so treat them as a guide.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.300 points to a short or a leaky part on that rail; a correct diode reading with no 3.3 V points upstream at the rail's source or enable.
  • No known-good resistance reading for this rail.
PP3V3_G3S_WLANBT0.300––
AI: what PP3V3_G3S_WLANBT is and how to check it

PP3V3_G3S_WLANBT is a 3.3 V rail for the Wi-Fi/Bluetooth section, and the G3S in its name marks it as an always-on (G3H-stage) supply. The only known-good figure recorded here is a diode reading of 0.300 to ground; no known-good voltage reading is listed. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the same point. A diode value far below 0.300 suggests a short or a leaky load on the rail; a far higher or open reading points to a broken feed or a missing part. Confirm with the voltage measurement before suspecting any part.

PP5V_G3S0.4335.000–
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V rail; the "G3S" suffix marks it as a startup-stage rail (from its name), and the archive lists it as a G3H always-on stage. Known-good readings here are diode 0.433 and voltage 5.000, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.433 usually points to a short or a leaky part on the rail; a voltage well off 5.000 suggests the rail isn't being enabled or its source is failing. These are community readings and only a guide.

PP5V_G3S_ALSCAM0.431––
AI: what PP5V_G3S_ALSCAM is and how to check it
  • What it is: PP5V_G3S_ALSCAM is a 5V rail. The G3S in the name (from the name) marks it as an always-on startup-stage rail, so it should be present whenever the board has power.
  • Known-good reading: diode 0.431 to ground. This is a community guide value and varies with board state; there is no known-good powered voltage for this rail in the data.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.431. Then apply power and measure the voltage at the same point.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; a correct diode reading with no 5V points upstream, toward whatever enables this rail. Confirm with a second measurement before replacing anything.
PP5V_G3S_ALSCAM_F0.431––
AI: what PP5V_G3S_ALSCAM_F is and how to check it

PP5V_G3S_ALSCAM_F is a 5 V rail; the "G3S" in its name (from the name) marks it as an always-on startup-stage rail, and "ALSCAM" suggests it feeds the camera circuit — that part is general naming, not from board data. The only known-good figure here is a diode reading of 0.431 to ground; there is no known-good voltage or resistance value for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.431 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path — treat these as guides, not proof, and confirm before replacing anything.

PP5V_G3S_CPUREG0.430––
AI: what PP5V_G3S_CPUREG is and how to check it

PP5V_G3S_CPUREG is a 5 V rail feeding the CPU regulator section; the G3S part of the name indicates it belongs to the always-on G3H startup stage, and that reading is from the name, not from a schematic. The only known-good figure here is a diode reading of 0.430 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage is listed for this rail. A diode reading far below 0.430 suggests a short or a leaky part on the rail, while a far higher or open reading points to a broken connection or missing component. Treat the 0.430 as a community guide, not a guaranteed value.

PP5V_G3S_DFR_FILT0.41––
AI: what PP5V_G3S_DFR_FILT is and how to check it
  • What it is: PP5V_G3S_DFR_FILT is a 5V rail. From the name, it's a G3S (startup-stage) supply that is always on, and the "FILT" suffix suggests a filtered version of that 5V feed. The board data doesn't name the parts on it.
  • Known-good reading: diode mode 0.41 to ground. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. A single reading isn't proof, so confirm before replacing anything.
PP5V_G3S_EDRAMPVCC0.434––
AI: what PP5V_G3S_EDRAMPVCC is and how to check it

PP5V_G3S_EDRAMPVCC is a 5V rail; the "G3S" part of the name indicates it belongs to the always-on (G3H/G3S) startup stage, and "EDRAMPVCC" suggests it feeds the eDRAM supply — both from the name only, not from board data.

  • Known-good: diode mode to ground 0.434. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far below 0.434 usually points to a short or leaky load on the rail; a much higher or open reading points to a broken connection. A voltage missing with a normal diode reading points upstream, to the rail's source or enable.
  • Confirm with a second measurement before replacing anything.
PP5V_G3S_EDRAMVCC0.434––
AI: what PP5V_G3S_EDRAMVCC is and how to check it
  • What it is: From the name, PP5V_G3S_EDRAMVCC is a 5 V rail in the G3S (always-on) group that supplies the eDRAM. That's general reading of the naming, not from board data.
  • Known-good reading: diode mode to ground is 0.434. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the same point.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail. Confirm with a second measurement before replacing anything.
PP5V_G3S_FAN_CONN0.428––
AI: what PP5V_G3S_FAN_CONN is and how to check it

PP5V_G3S_FAN_CONN is a 5 V rail feeding the fan connector; the G3S part of the name indicates it comes up in the G3/S5 startup stage (from the name, not from a schematic). The only known-good reading in the archive is diode 0.428 to ground, with no stated condition. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the fan connector. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.428 usually points to a short or a damaged fan or connector, but one reading alone doesn't confirm a bad part.

PP5V_G3S_KBD0.427––
AI: what PP5V_G3S_KBD is and how to check it

PP5V_G3S_KBD is a 5 V always-on rail (G3S, from its name) that feeds the keyboard on this 820-00850. The only known-good reading here is a diode value of 0.427 to ground; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from PP5V_G3S_KBD to ground and compare with 0.427. A much lower reading suggests a short or leaky part on the rail; a much higher one can mean an open trace or missing part.
  • Then apply power and check the voltage at the rail; expect about 5 V, but that is general expectation, not a recorded value here.
  • If the diode reading is far off, the usual suspects are a shorted capacitor or load on the rail, but that is a likely cause, not a confirmed one.
PP5V_G3S_TPAD0.428––
AI: what PP5V_G3S_TPAD is and how to check it

PP5V_G3S_TPAD — a 5 V rail for the trackpad, from the name; the G3S part of the name marks it as a startup-stage rail.

  • Known-good reading in the archive: diode 0.428 (no condition recorded). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe to ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.428 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault — compare with a known-good board if possible.
PP5V_G3S_TPAD_CONN0.428––
AI: what PP5V_G3S_TPAD_CONN is and how to check it

PP5V_G3S_TPAD_CONN is a 5 V rail feeding the trackpad connector, judged from its name; the "G3S" part means it belongs to the always-on G3H/G3S startup group, so it should be present once that stage is up. The only known-good figure in the archive is a diode reading of 0.428 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below 0.428 usually suggests a short or leaky load on the rail; a far higher or open reading points to a broken connection or missing feed, but one reading alone doesn't confirm a bad part.

PP5V_G3S_VCCIOPVCC0.431––
AI: what PP5V_G3S_VCCIOPVCC is and how to check it

PP5V_G3S_VCCIOPVCC is a 5 V rail; the "G3S" part of the name indicates it belongs to the G3H always-on group, and "VCCIO" suggests an I/O supply (that reading is from the name, not from board data). The only known-good figure in the archive is a diode reading of 0.431 to ground; there is no known-good voltage reading here.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.431.
  • Then apply power and measure the voltage; expect about 5 V, but that is general expectation, not a recorded value.

A diode reading far below 0.431 usually points to a short or a leaky load on the rail; a much higher or open reading can mean a broken feed. Treat these as a guide only, since community readings vary with board state, and confirm with a second measurement before suspecting a part.

PP5V_G3S_VCCIOVCC0.432––
AI: what PP5V_G3S_VCCIOVCC is and how to check it

PP5V_G3S_VCCIOVCC is a 5V rail; the G3S part of the name (from the name) puts it in the always-on startup group, and VCCIOVCC suggests it feeds I/O supply on the board. The only known-good figure here is a diode reading of 0.432 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode from the rail to ground and compare with 0.432, then power up and measure the voltage, expecting about 5V from the name. A diode reading far below 0.432 usually points to a short or a leaky part on the rail, while a far higher or open reading points to a broken connection; a missing voltage with a good diode reading points upstream to the rail's source. These community readings are a guide only and vary with board state, so confirm against a matching net or a known-good board before replacing anything.

PPBUS_G3H0.46012.220–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus rail; the "G3H" suffix indicates it is always-on (from the name). Known-good readings here are diode 0.460 and voltage 12.220, community-contributed and a guide only. Check it with the board unpowered in diode mode to ground, then with power applied measure the voltage. A reading far from these usually points to the charging circuit (U7000 area) or the switching MOSFETs Q7030/Q7040 not opening, but that is a likely cause, not confirmed.

PPBUS_G3H_SPKRAMP_LEFT0.46912.500–
AI: what PPBUS_G3H_SPKRAMP_LEFT is and how to check it

PPBUS_G3H_SPKRAMP_LEFT is the speaker-amp supply derived from PPBUS_G3H; the G3H part of the name indicates an always-on rail, and the SPKRAMP_LEFT part indicates it feeds the left speaker amplifier (from the name). Known-good readings in the archive: diode 0.469 and 12.500 V, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.469 suggests a short or leaky part on that rail; a voltage far from 12.5 V points to the upstream supply or an excessive load. No known-good resistance reading is recorded here.

PPBUS_G3H_SPKRAMP_RIGHT0.46013.100–
AI: what PPBUS_G3H_SPKRAMP_RIGHT is and how to check it

PPBUS_G3H_SPKRAMP_RIGHT is a speaker-amp supply derived from the main PPBUS_G3H rail; the "G3H" part of the name means it's always on once the charger brings up PPBUS_G3H, and "SPKRAMP_RIGHT" marks it as the right-channel amp feed (this is from the name, not the data).

Known-good readings here: diode 0.460 to ground, and 13.100 V with power applied. These come from community contributions, so treat them as a guide.

To check it: with the board unpowered, measure diode mode from the rail to ground and compare with 0.460; then apply power and measure the voltage, expecting about 13.1 V. A far lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path back to PPBUS_G3H. No known-good resistance reading exists here, so compare against a matching rail on a known-good board if needed.

PPBUS_G3H_SSD00.46013.100–
AI: what PPBUS_G3H_SSD0 is and how to check it

PPBUS_G3H_SSD0 is the main PPBUS rail feeding the SSD section; the G3H in the name indicates an always-on rail (from the name). The archive lists diode 0.460 and voltage 13.100 as known-good, with no condition noted, so treat them as a guide.

  • Check it unpowered in diode mode to ground; a reading far from 0.460 can mean a short or a leaky part on the rail.
  • With power applied, expect about 13.1 V; much lower suggests the rail isn't coming up, much higher suggests a regulation fault.
  • No known-good resistance reading here, so compare against a matching rail or a known-good board.

These are community readings and vary with board state, so confirm with a second measurement before replacing anything.

PPDCIN_G3H0.55820.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main DC input rail after the USB-C input switches, in the always-on G3H startup stage (from the rail name). Known-good readings here: diode 0.558 to ground, and 20.000 V with a charger applied and the board in its 20 V state.

  • Unpowered: diode mode from PPDCIN_G3H to ground; compare with 0.558. A near-zero reading suggests a short on the rail.
  • Powered: measure the voltage at PPDCIN_G3H (the notes also check it at C7000 pin 1 and at Q3100/QB300/QB400 pin 8). It should reach 20 V once the CD3215 units have negotiated 20 V.
  • A low or missing voltage points upstream, to the input switch and its gate drive, rather than to the rail itself. No known-good resistance reading is recorded here.

These are community readings and only a guide; a small difference is not proof of a bad part.

PPDCIN_G3H_CHGR0.558––
AI: what PPDCIN_G3H_CHGR is and how to check it
  • What it is: From the name, PPDCIN_G3H_CHGR is the charger-side DC input rail that sits in the G3H "always on" startup stage — the input the charger circuit works from before the main rails come up.
  • Known-good reading: diode 0.558 to ground, from the readings archive. That's a community figure and varies with board state, so treat it as a guide.
  • How to check: power off and unplug, then diode mode from PPDCIN_G3H_CHGR to ground. Then apply power and measure the voltage on the rail; the archive gives no known-good voltage for this net, so compare against a matching input net on another USB-C side or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail, while an open reading points to a broken path. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R0.46013.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is a battery/charger rail; the G3H part of the name indicates an always-on startup rail (from the name, not from a schematic). Known-good readings here are diode 0.460 and voltage 13.100, community-sourced and only a guide. Check it unpowered in diode mode to ground, then its voltage with power applied. No known-good resistance reading is recorded for this rail. A reading far from known-good usually points to a short or open on that rail, but confirm with a second measurement before suspecting a part.

PPVBAT_G3H_CHGR_REG0.46012.220–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a charger-side battery rail; the G3H part of the name indicates it is always-on, and CHGR points to the charger circuit (from the name). In the readings archive its known-good values are diode 0.460 and voltage 12.220; treat these as a guide, since community readings vary with board state.

To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far from 0.460 usually points to a short or a damaged component on that rail; a voltage far from 12.220 points to the charger not regulating or the rail being loaded down. There is no known-good resistance reading here, so compare against a matching net or a known-good board.

PPVBAT_G3H_CONN1.566––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector rail; the G3H part of the name indicates it is always-on, and that reading is from the name, not from a schematic. The only known-good figure here is a diode reading of 1.566 to ground, with no condition recorded; there is no known-good voltage or resistance for this rail. Check it with the board unpowered and the battery disconnected, in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 1.566 usually points to a short or a damaged component on that rail, but a single off reading is only a guide, so confirm before replacing anything.

PPVIN_G3H_P3V3G3H0.46013.100–
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H — reference note

  • This is a G3H (always-on) rail feeding the 3V3 G3H regulator input; the "G3H" and "P3V3G3H" parts come from the rail name, not from a schematic here.
  • Known-good readings from the archive: diode 0.460 and voltage 13.100. These are community values and only a guide; the data gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the rail voltage, expecting roughly the 13.1 V figure.
  • A diode reading well below 0.460 suggests a short or leaky load on the rail; a voltage far off 13.1 V points to the upstream supply or the rail's own regulator. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PPVIN_G3H_P3V3G3HRTC0.46013.100–
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC is a G3H (always-on) rail feeding the 3V3 G3H RTC supply; the G3H part comes from the rail name. In the archive its known-good readings are diode 0.460 and voltage 13.100, with no condition stated, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading well below 0.460 suggests a short or leaky load on the rail; a voltage far from 13.100 points to the supply or upstream feed, but one reading alone doesn't confirm a bad part. No known-good resistance reading is listed here.

PPVIN_G3H_P3V3G3HRTC_R0.46212.000–
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it

PPVIN_G3H_P3V3G3HRTC_R — the name suggests it's the input feed for the always-on 3V3 G3H RTC rail (the "G3H" part means always on, from the name). It's a general naming reading, not a confirmed circuit description.

  • Known-good from the archive: diode 0.462 to ground, voltage 12.000 with power applied.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far from 0.462 usually points to a short or leaky part on that rail; a voltage far from 12 V points to the feed or upstream supply.
  • No known-good resistance reading is listed for this rail.
PPVIN_G3H_P5VG3S0.46013.100–
AI: what PPVIN_G3H_P5VG3S is and how to check it
  • What it is: From the name, PPVIN_G3H_P5VG3S is a G3H (always-on) input rail feeding the P5VG3S supply. The board data doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.460 to ground, voltage 13.100. No condition is recorded for these.
  • How to check: Power off, measure diode mode from the rail to ground; then power the board and measure the voltage on the same point.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; wrong voltage with a normal diode reading points upstream at the supply feeding it. These are likely causes, not confirmed ones — compare against a matching net or known-good board before replacing anything.

S5 and SUS: standby 6

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V05_S5_PCH_VCCDSW0.490––
AI: what PP1V05_S5_PCH_VCCDSW is and how to check it
  • What it is: PP1V05_S5_PCH_VCCDSW is a 1.05 V rail for the PCH, from its name. The S5/SUS part of the name puts it in the standby stage, so it should be present before the board fully powers on (general reading of the name, not from board data).
  • Known-good reading: diode mode to ground 0.490. That is the only known-good value recorded for this rail; there is no known-good voltage or resistance
PP1V8_S50.327––
AI: what PP1V8_S5 is and how to check it

PP1V8_S5 is a 1.8 V rail; the "S5" in its name places it in the standby stage, so it should be present before the board fully powers on (this is from the name, not from board data). The only known-good reading in the archive is a diode value of 0.327 to ground, with no condition recorded; there is no known-good voltage reading for this rail here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.327 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.

PP1V24_S5_PCH_VCCDPHY0.429––
AI: what PP1V24_S5_PCH_VCCDPHY is and how to check it

PP1V24_S5_PCH_VCCDPHY is a 1.24 V rail for the PCH's display PHY, and the S5/SUS part of the name places it in the standby stage. From the readings archive, its only known-good value is a diode reading of 0.429 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power up and measure the voltage at the same point. A diode reading far below 0.429 suggests a short or leaky load on the rail, while a far higher one can mean an open path; either way, confirm with a second measurement before suspecting a part.

PP3V3_S50.300––
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is a 3.3 V standby rail; the "S5" in the name places it in the standby stage, so it should be present before the board fully powers on.
  • Known-good reading: diode mode to ground 0.300 (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a correct diode reading with no voltage points upstream, to whatever should be generating the rail. Confirm with a second measurement before replacing anything.
PP5V_S5_LDO0.45––
AI: what PP5V_S5_LDO is and how to check it
  • PP5V_S5_LDO is a 5V standby rail; the S5/SUS part of the name places it in the standby stage (from the name).
  • Known-good: diode reading 0.45 to ground. No known-good voltage reading here.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail.
  • A diode reading far from 0.45 suggests a short or leaky part on that rail; confirm with a second reading before replacing anything.
PPVPCORE_S50.3151.000–
AI: what PPVPCORE_S5 is and how to check it

PPVPCORE_S5 is a standby-stage rail (S5/SUS, from the name) — in general terms, the always-on core supply that comes up before the board fully wakes. The archive lists a known-good diode reading of 0.315 and a voltage of 1.000; no condition is recorded for either, so treat them as a guide only.

  • Check it unpowered in diode mode from the rail to ground; a reading far below 0.315 usually points to a short or a leaky load on the rail, while a much higher one can mean an open path.
  • Then apply power and measure the voltage; it should sit near 1.000 V once the rail is up.
  • No known-good resistance reading exists for this rail, so compare against a matching rail or a known-good board if you need one.

S4 7

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S4SW_SNS0.515––
AI: what PP3V3_S4SW_SNS is and how to check it
  • What it is: PP3V3_S4SW_SNS is a 3.3 V rail in the S4 startup stage, judged from its name; the "SW" and "SNS" parts suggest a switched rail with a sense line. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.515 to ground, from the community readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.515. Then apply power and measure the voltage at the rail; there is no known-good voltage in the data, so compare against a matching rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open. A single reading isn't proof, so confirm with a second measurement before replacing anything.
PP5V_S4_T_USBC0.5055.000–
AI: what PP5V_S4_T_USBC is and how to check it

PP5V_S4_T_USBC is a 5 V rail at the S4 startup stage, judged from its name (S4 is a later power-sequence stage); the "T_USBC" suffix suggests it feeds a USB-C related section, but that is general inference, not from this board's data.

  • Known-good readings in the archive: diode 0.505 and voltage 5.000 V. No condition is recorded with them, so treat them as a guide.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the same point.
  • A diode reading far below 0.505 suggests a short or leaky part on the rail; a voltage well off 5.000 V with power applied points to the rail not being enabled or its source failing. No known-good resistance reading exists for this rail.
  • One reading alone doesn't confirm a bad part, so compare with a matching rail on the other side of the pair before replacing anything.
PP5V_S4_WLAN_ISNS_DOL––
AI: what PP5V_S4_WLAN_ISNS_D is and how to check it
  • What it is: From its name, PP5V_S4_WLAN_ISNS_D is a 5 V rail in the S4 startup stage, tied to the WLAN section and used as a current-sense (ISNS) line. The archive doesn't say which parts sit on it.
  • Known-good readings: The only one recorded is diode mode OL (open) on the net itself. There's no known-good voltage or resistance here.
  • How to check: With the board unpowered, measure diode mode from PP5V_S4_WLAN_ISNS_D to ground and expect OL. Then apply power and measure the voltage on the net.
  • What a far-off reading suggests: A diode reading well below OL points to a short or a low-impedance path on that net, not a confirmed bad part. Compare against a matching net on the other side of the pair before replacing anything.
PP5V_S4_X_USBC0.503––
AI: what PP5V_S4_X_USBC is and how to check it

PP5V_S4_X_USBC is a 5V rail tied to the USB-C path on this board; the S4 in the name marks it as a later startup stage (from the name). The only known-good figure here is a diode reading of 0.503 to ground, with no condition recorded, and there is no known-good voltage reading for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.503.
  • With power applied, check the voltage; no known-good value is recorded, so compare against a matching rail on the other USB-C side or a known-good board.
  • A diode reading far below 0.503 suggests a short or a leaky part on the rail; a far higher or open reading suggests a broken connection.

These readings are community guides and vary with board state, so treat a small difference as normal before suspecting a part.

PP5V_S4SWOL––
AI: what PP5V_S4SW is and how to check it
  • What it is: PP5V_S4SW is a 5 V switched rail in the S4 startup stage, judged from its name. It isn't covered by the community notes here, so there is no known-good voltage or diode reading for it.
  • Diode check: With the board unpowered, measure diode mode from the rail to ground. Compare with a matching 5 V switched rail elsewhere on the board, or a known-good board, since no reference value exists here.
  • Voltage check: With power applied, measure the rail and confirm it comes up when the board reaches S4. A reading far from 5 V points to the rail's enable or switch not turning on, not necessarily a shorted part.
  • Next step: Trace the rail's source and enable before replacing anything.
PP5V_S4SW_ISNSOL––
AI: what PP5V_S4SW_ISNS is and how to check it

PP5V_S4SW_ISNS is a 5V rail that switches on at the S4 startup stage — that reading comes from the name, not from board data. The only known-good reading recorded here is diode OL (open line) on the net itself; there is no known-good voltage or resistance value for it. Check it unpowered in diode mode from the net to ground, then measure the voltage with power applied and the board at S4. A diode reading far below OL suggests a short or leaky load on the rail; no voltage at S4 points upstream to the switch or enable that feeds it.

PPVIN_S4_TPAD_FUSE0.46713.100–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE is the S4-stage input rail feeding the trackpad section; the "S4" startup stage and "TPAD" meaning come from the rail name, not from measured data. Known-good readings here are diode 0.467 and voltage 13.100 (community-contributed, so treat them as a guide). Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.467 can point to a shorted load on the rail; a voltage well off 13.100 suggests the rail isn't being enabled or is loaded down. No known-good resistance reading exists for this rail.

S3: memory 9

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.380––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it
  • What it is: PP0V6_S3_MEM_VREFCA_A is a 0.6 V memory reference rail, judged from its name; the S3 part suggests it comes up in the memory stage of startup. General knowledge, not from this board's data.
  • Known-good reading: diode mode to ground 0.380, with no condition recorded. There is no known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.380 suggests a short or a leaky part on the rail; a much higher one suggests an open connection. Confirm with a voltage check before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.381––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail; the "S3" and "MEM" parts of the name indicate it belongs to the memory stage of the S3 power state, and "VREFDQ" suggests a DDR data-reference voltage (general naming, not from this board's data).

  • Known-good: diode 0.381 in diode mode to ground, board unpowered. No known-good voltage reading is recorded here.
  • Check it with the board off: diode mode, black probe on ground, red on the rail, and compare with 0.381.
  • Then power the board and measure the voltage; no known-good voltage exists here, so compare against a matching rail on the other memory channel or a known-good board.
  • A diode reading far from 0.381 usually points to a short or a damaged part on that net, but one reading alone doesn't confirm a fault.
PP0V6_S3_MEM_VREFDQ_B0.379––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail; the "S3" and "MEM" parts of the name indicate it belongs to the memory stage, and "VREFDQ" suggests a DDR data-reference voltage (that reading is from the name, not from board data). The only known-good figure here is a diode reading of 0.379 to ground; there is no known-good voltage or resistance value for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S3. A diode reading far below 0.379 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path; either way, compare against a matching rail before condemning anything.

PP1V_S30.238––
AI: what PP1V_S3 is and how to check it

PP1V_S3 is a 1.1 V rail; the "S3" in its name marks it as a memory-stage (S3) supply, and that stage comes from the name rather than from circuit data. The only known-good figure here is a diode reading of 0.238 to ground; no known-good voltage reading is recorded for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.238 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP1V2_S30.2161.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail; the S3 suffix comes from its name and marks it as a memory (S3) startup-stage rail. Known-good readings here are diode 0.216 in diode mode and 1.200 V with power applied; no condition is recorded for either.

Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.216 usually suggests a short or a damaged part on the rail; a voltage well off 1.200 V with a normal diode reading points more to the rail not being enabled or its source not coming up. There is no known-good resistance reading for this rail, so compare against a matching net or a known-good board.

PP1V2_S3_CPUDDR0.218––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is a 1.2 V rail; the "S3" in its name marks it as a memory (DDR) rail in the startup sequence, and "CPUDDR" points to the CPU's DDR supply. The only known-good figure here is a diode reading of 0.218 to ground, with no condition recorded; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage.
  • A diode reading far below 0.218 suggests a short or a leaky load on the rail; a reading far above it can mean an open path, so compare against the same rail on a known-good board before condemning anything.
  • For the voltage, the name implies roughly 1.2 V, but that is general expectation, not a value from this board's data.

These readings are community guides and vary with board state, so treat a single off reading as a hint, not proof.

PP1V2_S3_REG_R0.2161.200–
AI: what PP1V2_S3_REG_R is and how to check it
  • What it is: PP1V2_S3_REG_R is a 1.2 V regulator rail in the S3 (memory) startup stage, judging by its name; the board data doesn't list which parts sit on it.
  • Known-good readings: diode 0.216 in diode mode, and 1.200 V with power applied. These are community readings and only a guide.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a low or shorted diode reading points to a short on the rail, and missing voltage points to the regulator or its enable not coming up. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PP1V8_S30.4201.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix in its name marks it as a memory-stage rail in the startup sequence. Known-good readings for this board: diode 0.420 to ground and 1.800 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading well below 0.420 suggests a short or leaky load on the rail; a voltage far from 1.800 V points to the rail not coming up or being pulled down, but one reading alone doesn't confirm a bad part. No known-good resistance reading here.

PP1V8_S3_MEM0.4201.800–
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM — the name indicates a 1.8 V rail that comes up at the S3 (memory) startup stage; that reading of the name is general, not from board data.

  • Known-good (community guide): diode 0.420 to ground, voltage 1.800.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail's test point.
  • Then power up and measure the voltage; it should sit at 1.800 V once the board reaches S3.
  • A diode reading well below 0.420 suggests a short or leaky load on the rail; a missing 1.8 V with a normal diode reading points upstream, to the rail's enable or supply. No known-good resistance reading here, so compare against a matching rail or a known-good board.

S0: running 28

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.151––
AI: what PP0V6_S0_DDRVTT is and how to check it
  • PP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the "S0" in the name indicates it belongs to the running (S0) state, and "DDRVTT" indicates DDR termination voltage. This is from the name only.
  • Known-good from the archive: diode mode to ground 0.151, no condition listed. No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running.
  • A diode reading far from 0.151 usually points to a short or a damaged part on that rail, but one reading isn't proof; compare against a known-good board before replacing anything.
PP0V95_S0_CPUVCCIO_REG_R0.0800.950123.700R
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it

PP0V95_S0_CPUVCCIO_REG_R — from its name, a 0.95 V rail feeding CPU VCCIO, in the S0 (running) state; it's a regulated supply, not a standby rail.

  • Known-good readings here: diode 0.080, voltage 0.950 V, resistance 123.700R. These are community readings and only a guide.
  • Check with the board unpowered: diode mode, red probe to ground, black to the rail. Then power up and measure the voltage.
  • A voltage well off 0.950 V, or a diode reading far from 0.080, usually points to a shorted or open load on the rail or a failed regulator — not proof on one reading. No known-good current draw is listed for this rail.
PP1V_S0SW0.229––
AI: what PP1V_S0SW is and how to check it

PP1V_S0SW is a 1.1 V rail in the S0 (running) state, judging by its name; the "SW" suffix usually means a switched rail, but that's general naming, not from this board's data. The only known-good value recorded here is a diode reading of 0.229 to ground, with no condition noted, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.229 suggests a short or a failing load on the rail; a reading well above it suggests an open path. Treat the 0.229 as a guide only, since community readings vary with board state.

PP1V2_S0SW0.240––
AI: what PP1V2_S0SW is and how to check it

PP1V2_S0SW is a 1.2 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "SW" usually means a switched rail (general naming, not from the board data). The only known-good figure here is a diode reading of 0.240 to ground, with no condition recorded; no known-good voltage is listed for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.240 suggests a short or a damaged component on that rail, but a single reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP1V8_S0_CPUTHMSNS_TI_R0.322––
AI: what PP1V8_S0_CPUTHMSNS_TI_R is and how to check it

PP1V8_S0_CPUTHMSNS_TI_R — the name indicates a 1.8 V rail (PP1V8) that is on in the S0 running state, and "CPUTHMSNS" suggests it carries a CPU thermal-sense signal; that reading of the name is general, not from board data.

  • Known-good: diode mode to ground 0.322. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the same point.
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. A single reading isn't proof — confirm before replacing anything.
PP1V8_S0_TBTTHMSNS_R0.325––
AI: what PP1V8_S0_TBTTHMSNS_R is and how to check it
  • What it is: PP1V8_S0_TBTTHMSNS_R is a 1.8 V rail, from its name: an S0 (running-state) supply, with "TBT" suggesting a Thunderbolt-related sense line. Which parts sit on it isn't known from the archive.
  • Known-good reading: diode 0.325 to ground, with no stated condition beyond the S0 stage. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the same point.
  • If it's far off: a much lower diode reading usually points to a shorted load on the rail; a missing voltage with a normal diode reading points upstream. Confirm with a second measurement before replacing anything.
PP1V8_S0_TBTTHMSNS_T_R0.321––
AI: what PP1V8_S0_TBTTHMSNS_T_R is and how to check it

PP1V8_S0_TBTTHMSNS_T_R is a 1.8 V rail; the "S0" in the name indicates it belongs to the running (S0) state, and "TBT" suggests it relates to the Thunderbolt subsystem (from the name only). The archive lists one known-good figure: diode mode 0.321 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.321 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S0_TBT_T_ISNS_R0.530––
AI: what PP3V3_S0_TBT_T_ISNS_R is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) active in the S0 running state, tied to Thunderbolt current sense (TBT_T_ISNS). The exact parts on it aren't documented here.
  • Known-good: Diode mode to ground is 0.530. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: A much lower diode reading suggests a short or leaky part on the rail; a missing voltage points upstream. Confirm with a second measurement before replacing anything.
PP3V3_S0_TBT_X_ISNS_R0.542––
AI: what PP3V3_S0_TBT_X_ISNS_R is and how to check it

PP3V3_S0_TBT_X_ISNS_R is a 3.3 V current-sense line on the Thunderbolt X side, judged from its name; the S0 suffix means it belongs to the running (S0) state, so it's only expected once the board is powered up. The only known-good reading here is a diode value of 0.542 to ground, with no condition recorded. Check it unpowered in diode mode to ground first, then measure the voltage with power applied; there is no known-good voltage reading here, so compare against a matching sense net on the other Thunderbolt side or a known-good board. A diode reading far from 0.542 usually points to a short or a damaged component on that net, but a small difference can be normal, so confirm with a second measurement before replacing anything.

PP3V3_S0SW_LCD0.548––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a 3.3 V switched LCD rail; the "S0" in the name marks it as a running-state rail, and "SW" suggests it is switched on rather than always present (that part is from the name, not from board data). The only known-good figure here is a diode reading of 0.548 to ground; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.548 usually points to a short or a leaky load on the rail, while a normal diode reading with no voltage present points upstream to the switch or enable that feeds it. Readings are community guides and vary with board state, so compare against a matching rail or a known-good board before condemning a part.

PP3V3_S0SW_LCD_R0.548––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R — the name indicates a 3.3 V rail (PP3V3) that is switched (SW) and in the S0 running state, feeding the LCD. "R" likely marks a variant or right-side rail; that part is from the name only.

  • Known-good from the archive: diode mode 0.548 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the voltage at the same point.
  • A diode reading far below 0.548 usually points to a short or a leaky part on the rail; far above suggests an open path. Confirm with a second measurement before replacing anything.
PP3V3_TBT_T_S00.5203.300–
AI: what PP3V3_TBT_T_S0 is and how to check it
  • What it is: PP3V3_TBT_T_S0 is a 3.3 V rail. The "S0" part of the name indicates the running (S0) power state; "TBT" usually points to the Thunderbolt section, but that is from the name only.
  • Known-good readings (community archive, guide only): diode 0.520 to ground, and 3.300 V with the board powered in S0.
  • How to check: with the board off and unplugged, measure diode mode from the rail to ground; then power up into S0 and measure the voltage.
  • If far off: a diode reading well below 0.520 suggests a short or a leaky load on the rail; a correct diode but missing 3.3 V points upstream at the rail's supply or enable. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board before condemning anything.
PP3V3_TBT_X_S00.543––
AI: what PP3V3_TBT_X_S0 is and how to check it
  • What it is: PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt (TBT) X side. The S0 suffix, from the name, means it belongs to the running state, so it should come up once the board is fully on, not in standby.
  • Known-good reading: diode 0.543 to ground (community archive, guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then power up and measure the voltage on the rail; expect about 3.3 V in S0.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail; an open reading suggests a missing feed or enable. Confirm with a second measurement before replacing anything.
PP5V_S0_BKLT_A0.433––
AI: what PP5V_S0_BKLT_A is and how to check it
  • What it is: PP5V_S0_BKLT_A is a 5 V backlight rail, from its name; the S0 suffix means it's expected only in the running state, after the board has powered on.
  • Known-good reading: diode 0.433 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board off and unplugged, measure diode mode from the rail to ground; then power up and measure the voltage, which should be about 5 V once the board is in S0.
  • If it's far off: a diode reading well below 0.433 suggests a short or leaky load on the rail; a correct diode reading but no 5 V points upstream at the backlight enable and supply, not the rail itself. Confirm with a second measurement before replacing anything.
PP5V_S0_BKLT_D0.433––
AI: what PP5V_S0_BKLT_D is and how to check it
  • What it is: PP5V_S0_BKLT_D is a 5 V backlight rail that runs in the S0 (fully on) state, judging from the name. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.433 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail in S0.
  • If it's far off: a diode reading well below 0.433 suggests a short or leaky load on the rail; a missing 5 V with a normal diode reading points upstream, to the rail's supply or enable. Treat these as likely causes, not confirmed.
PP5V_S0SW_LCD0.570––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD — from the name, a 5 V rail switched in the S0 (running) state, feeding the LCD. The archive lists one known-good reading: diode 0.570 to ground. No known-good voltage reading is recorded here.

  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. A far lower reading suggests a short or a leaky part on the rail; a far higher or open reading suggests a broken feed or a missing connection.
  • Then power the board and measure the voltage in the S0 state; there is no known-good voltage in this data, so compare against a matching rail on a known-good board.
  • A missing 5 V here points upstream to the rail's switch or its source, not necessarily to the LCD side.
PP5V_S0SW_LCD_ISNS_R0.570––
AI: what PP5V_S0SW_LCD_ISNS_R is and how to check it

PP5V_S0SW_LCD_ISNS_R is a 5V S0 (running-state) rail; the "ISNS" part of the name suggests it's a current-sense line for the LCD supply, and "S0" means it should only be up once the board is running — that reading is from the name, not from board data. The only known-good figure here is a diode reading of 0.570 to ground, with no condition noted, so treat it as a guide. Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail. There is no known-good voltage reading for this net, so compare against a matching net or a known-good board rather than a fixed number. A diode reading far below 0.570 usually points to a short or a leaky part on that net, but confirm with a second measurement before replacing anything.

PPVCC_S0_CPU0.0051.5004.400R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the "S0" in its name marks it as a running-state rail, so it should only be present once the board is fully on. The archive lists a diode reading of 0.005, 1.500 V, and 4.400R, but no condition is recorded for these, so treat them as a rough guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; a diode value far above the known-good one suggests an open or high-resistance path, while a near-zero value points to a short on the rail. No known-good resistance condition is recorded here, so compare against a matching rail or a known-good board before condemning anything.

PPVCCEDRAM_S0_CPU0.0501.00037.100R
AI: what PPVCCEDRAM_S0_CPU is and how to check it

PPVCCEDRAM_S0_CPU is a CPU-side power rail for the eDRAM, based on its name; the S0 suffix means it belongs to the running state. The archived readings for this net are diode 0.050, voltage 1.000 and resistance 37.100R, and these are community figures that vary with board state, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A reading far from 0.050 in diode mode, or a voltage well off 1.000, usually points to a short or a missing supply on that rail rather than a confirmed bad part. There is no known-good current draw or waveform reading here, so compare against a matching rail or a known-good board before replacing anything.

PPVCCEDRAM_S0_REG_R0.0501.00034.300R
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R is a running-state (S0, from the name) supply rail for the eDRAM, likely a regulator output feeding memory. Known-good readings here: diode 0.050, voltage 1.000, resistance 34.300R. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied and the board running. A diode or resistance far below known-good usually points to a short or a failing load on the rail; a voltage well off 1.000 suggests the regulator or its enable isn't working. These are community readings and only a guide, and no known-good current draw is listed here.

PPVCCGT_S0_CPU0.0051.5004.600R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU is the CPU graphics rail; the "S0" in the name marks it as a running-state rail (from the name). The archive lists a known-good diode reading of 0.005, about 1.500 V with power applied, and 4.600R resistance — treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A reading far from these usually points to a short or a failed supply on that rail, but one odd reading isn't proof — confirm before replacing anything.

PPVCCIO_S0_CPU0.1270.950123.700
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is a CPU I/O supply rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "VCCIO" indicates an I/O rail — that reading is from the name, not from a schematic. Known-good community readings for this board: diode 0.127, voltage 0.950 V, resistance 123.700 (no condition stated, so treat them as a guide). Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode or resistance far below known-good usually suggests a short or a leaky load on the rail; a voltage far off 0.950 V points to the rail not being enabled or its source failing — but one reading alone doesn't confirm a bad part. No known-good waveform or current reading exists here.

PPVCCSA_S0_CPU0.0241.15022.100R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is the CPU system-agent supply; the "S0" in its name marks it as a running-state rail. Known-good readings here are diode 0.024, voltage 1.150 V and resistance 22.100R — community figures, so treat them as a guide. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered and running. A reading far from known-good usually points to a short or a failed supply on that rail, but confirm with a second measurement before replacing anything.

PPVIN_S0_CPUVR_VIN0.473––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it
  • What it is: From its name, PPVIN_S0_CPUVR_VIN is the input supply to the CPU voltage regulator, active in the S0 (running) state. The name is the only description available here.
  • Known-good reading: diode mode 0.473 to ground. That is the only value recorded for this net; there is no known-good voltage or resistance reading here.
  • How to check: power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on that rail; a much higher one to an open path. A small difference can be normal, so confirm with a second reading before replacing anything.
PPVIN_S0SW_LCDBKLT0.82712.900–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail; the S0 in the name marks it as a running-state rail, and the rest of the name points to the LCD backlight. The archive lists diode 0.827 and voltage 12.900 for it, with no condition noted, so treat those as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.827 usually points to a short or a leaky part on the rail, while a missing or low voltage with power applied points upstream to the backlight supply. No known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT_F0.460––
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it
  • What it is: From the name, this is the switched input rail feeding the LCD backlight circuit, active at S0 (running). The board data doesn't list which parts sit on it.
  • Known-good: diode reading of 0.460 to ground. No known-good voltage reading here, so compare against a matching backlight rail or a known-good board.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted component on the rail, but one reading isn't proof — confirm before replacing anything.
PPVIN_S0SW_LCDBKLT_R0.460––
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it
  • What it is: From the name, a switched S0 (running-state) supply rail feeding the LCD backlight on the 820-00850. The name says it's a switched rail, so it's expected only once the board is in S0.
  • Known-good reading: diode 0.460 (community archive, guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from PPVIN_S0SW_LCDBKLT_R to ground; then power up and measure the voltage on the rail once the board is running.
  • If it's far off: a low or shorted diode reading points to a short on that rail or its load; a correct diode reading with no voltage points to the backlight switch/enable side, not the rail itself. Confirm with the voltage measurement before replacing anything.
PPVOUT_S0_LCDBKLT1.18355.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight boost output; the "S0" in the name indicates it belongs to the running (S0) power state, and "LCDBKLT" says it feeds the panel backlight. Known-good readings in the archive: diode 1.183 to ground, and 55.000 V with power applied. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board running and the display connected. A diode reading far below 1.183 suggests a short or leaky part on the rail; much higher can mean an open path. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

Repair notes

CD3215 Repeat checks for each unit, U3100,3200, UB300, 400

UB300

0V6 diode mode on USBC_TA_CC1 at CB313 pin 1 0V6 diode mode on USBC_TA_CC2 at CB314 pin 1 5V on FB200 pin 1 3V3 on CB308 pin 1 1V8 on CB305 pin 1 1V8 on CB306 pin 1 1V1 on CB304 pin 1 ~26V on QB300 pin 1 and QB300 pin 4 Check PPDCIN_G3H on QB300 pin 8

UB400

0V6 diode mode on USBC_TB_CC1 at CB413 pin 1 0V6 diode mode on USBC_TB_CC2 at CB414 pin 1 5V on FB201 pin 1 3V3 on CB408 pin 1 1V8 on CB405 pin 1 1V8 on CB406 pin 1 1V1 on CB404 pin 1 ~26V on QB400 pin 1 and QB400 pin 4 Check PPDCIN_G3H on QB400 pin 8

U3100

0V6 diode mode on USBC_XA_CC1 at C3113 pin 1 0V6 diode mode on USBC_XA_CC2 at C3114 pin 1 5V on F3000 pin 1 3V3 on C3108 pin 1 1V8 on C3105 pin 1 1V8 on C3106 pin 1 1V1 on C3104 pin 1 Check 26V on Q3100 pin 1 and Q3100 pin 4 Check PPDCIN_G3H on Q3100 pin 8

U3200

0V6 diode mode on USBC_XB_CC1 at C3213 pin 1 0V6 diode mode on USBC_XB_CC2 at C3214 pin 1 5V on F3001 pin 1 3V3 on C3208 pin 1 1V8 on C3205 pin 1 1V8 on C3206 pin 1 1V1 on C3204 pin 1 Check 26V on Q3200 pin 1 and Q3200 pin 4 Check PPDCIN_G3H on Q3200 pin 8

5V to 20V sequence

USBC CC1/2 & T2-SMC I2C Diode mode ~0V6 on USB_XA_CC1 at C3113 pin 1 Diode mode ~0V6 on USB_XA_CC2 at C3114 pin 1 Diode mode ~0V6 on I2C_UPC_SDA at R5220 pin 2 Diode mode ~0V6 on I2C_UPC_SCL at R5221 pin 2 Power getting to the CD3215... 5V on PP20V_USBC_XA_VBUS at F3000 pin 1 Basic CD3215 voltages + LDOs... 3V3 on PP3V3_UPC_XA_LDO at C3108 pin 1 1V8 on PP1V8_UPC_XA_LDOA at C3106 pin 1 1V8 on PP1V8_UPC_XA_LDOD at C3105 pin 1 1V1 on PP1V1_UPC_XA_LDO_BMC at C3104 pin 1 Open Q3100 so power goes through to PPDCIN_G3H... >5V on UPC_XA_GATE1 at Q3100 pin 1 >5V on UPC_XA_GATE2 at Q3100 pin 4 5V on PPDCIN_G3H at C7000 pin 1 Power to the ISL U7000 ... (in) 5V on TBA_VDDA at C7075 pin 1 (out) >=3V3 on CHGR_EN_MVR at R6907 pin 2 Getting PP3V3_G3H_RTC ... 3V3 on PP3V3_G3H_RTC at L6900 pin 1 20V switch over... 20V on PP20V_USBC_XA_VBUS at F3000 pin 1 >20V on UPC_XA_GATE1 at Q3100 pin 1 >20V on UPC_XA_GATE2 at Q3100 pin 4 20V on PPDCIN_G3H at C7000 pin 1 Final steps... 5V on TBA_AUX_DET at C7016 pin 1 MOSFETS Q7030 and Q7040 should now be open U7000 should be generating PPBUS_G3H Other things to check... Measure R7075 for 4R7 value

Every net with a reading

NetDiodeVoltageResistance
50_0_ANT0.000––
50_1_ANT0.000––
50_2_ANT0.000––
ACCEL_INT10.472––
ACT_GND0.000–0.300R
ADC1_REFCOMPOL––
ADC2_REFCOMPOL––
ALL_SYS_PWRGD0.555––
ALL_SYS_PWRGD_R0.487––
AP_PCIE_WAKE_L0.530––
AUD_CONN_HP_LEFT0.710––
AUD_CONN_HP_RIGHT0.710––
AUD_CONN_HP_SENSE_L1.270––
AUD_CONN_HP_SENSE_R1.269––
AUD_CONN_RING_SENSE0.639––
AUD_CONN_RING20.000––
AUD_CONN_RING2_XW0.631––
AUD_CONN_SLEEVE0.003–1.300R
AUD_CONN_SLEEVE_XW0.629––
AUD_CONN_TIP_SENSE1.482––
AUD_HP_PORT_CH_GND0.001–1.200R
AUD_HP_PORT_L0.710––
AUD_HP_PORT_R0.712––
AUD_HP_PORT_US_GND0.000–1.200R
AUD_HP_SENSE_L1.270––
AUD_HP_SENSE_R1.270––
AUD_HS_MIC_N0.632––
AUD_HS_MIC_P0.630––
AUD_PWR_EN0.774––
AUD_RING_SENSE0.635––
AUD_TIP_SENSE1.606––
BKLT_EN_R0.562––
BKLT_PWM_KEYB0.560––
BKLT_PWM_MLB2TCON0.827––
BKLT_SCL0.555––
BKLT_SDA0.556––
BKLT_SENSE_OUT0.739––
BMON_IOUTOL––
BOARD_REV00.456––
BOARD_REV10.465––
BOARD_REV20.461––
BOOT_CONFIG00.464––
BOOT_CONFIG10.462––
BOOT_CONFIG20.464––
BT_PWR_EN0.483––
BT_SFLASH_CS_L0.696––
BT_SFLASH_HOLD_L0.658––
BT_SFLASH_WP_L0.662––
BT_SPI2_CSN0.726––
BTUARTMUX_OE_L0.503––
BTUARTMUX_SEL_PCH0.458––
CHGR_AMON0.623––
CHGR_AUX_DET0.626––
CHGR_BGATE0.638––
CHGR_BMON0.623––
CHGR_BOOT10.591––
CHGR_BOOT1_RC0.595––
CHGR_BOOT20.588––
CHGR_BOOT2_RC0.590––
CHGR_COMP0.623––
CHGR_CSI_N0.560––
CHGR_CSI_P0.560––
CHGR_CSI_R_N0.558––
CHGR_CSI_R_P0.558––
CHGR_CSO_N0.467––
CHGR_CSO_P0.468––
CHGR_CSO_R_N0.46013.100–
CHGR_CSO_R_P0.46013.100–
CHGR_EN_MVR0.607––
CHGR_EN_MVR_R0.609––
CHGR_GATE_Q10.770––
CHGR_GATE_Q20.452––
CHGR_INT_L0.602––
CHGR_LX10.48013.100–
CHGR_LX20.48013.100–
CHGR_RST_IN0.620––
CHGR_RST_IN_R0.600––
CHGR_VDDA0.450––
CHGR_VDDP0.449––
CODEC_INT_L0.461––
CODEC_LDO_EN0.781––
CODEC_RESET_L0.464––
CODEC_WAKE_L0.464––
COMP_A_CPUGT0.625––
COMP_A_CPUGT_LOL––
COMP_B_CPUCORE0.58––
COMP_B_CPUCORE_LOL––
COMP_C_CPUSA0.625––
COMP_C_CPUSA_LOL––
CORE_ISUMN_R1.011––
CPU_C10_GATE_L0.754––
CPU_CATERR_L0.255––
CPU_CFG_RCOMP0.053–50.200R
CPU_CFG<3>0.309––
CPU_CFG<4>0.292––
CPU_DDR_RCOMP<0>0.197––
CPU_DDR_RCOMP<1>0.082–81.000R
CPU_DDR_RCOMP<2>0.163––
CPU_DIMM_VREFCA0.384––
CPU_DIMMB_VREFDQ0.388––
CPU_INPUT3VSEL0.831––
CPU_IST_TRIG0.353––
CPU_PECI0.284––
CPU_PROCHOT_L0.458––
CPU_PROCHOT_OUT_L0.297––
CPU_PROCHOT_R_L0.313––
CPU_VCCEOPIOSENSE_N0.003–0.700R
CPU_VCCEOPIOSENSE_P0.042–39.900R
CPU_VCCEOPIOSENSE_R0.051–49.700R
CPU_VCCEOPIOSENSE_XW0.003–1.300R
CPU_VCCGTSENSE_N0.003–1.500R
CPU_VCCGTSENSE_P0.007–5.800R
CPU_VCCIOSENSE_N0.001–0.400R
CPU_VCCIOSENSE_P0.132––
CPU_VCCIOSENSE_R0.205––
CPU_VCCIOSENSE_XW0.003–1.500R
CPU_VCCSASENSE_N0.003–1.300R
CPU_VCCSASENSE_P0.027–24.800R
CPU_VCCSENSE_N0.002–0.800R
CPU_VCCSENSE_P0.007–5.600R
CPU_VCCST_PWRGD0.517––
CPU_VCCST_PWRGD_R0.542––
CPU_VIDALERT_L0.295––
CPU_VIDALERT_R_L0.517––
CPU_VIDSCLK0.256––
CPU_VIDSCLK_R0.256––
CPU_VIDSOUT0.258––
CPU_VIDSOUT_R0.358––
CPU_VR_EN_R0.485––
CPU_VR_PROCHOT_L0.518––
CPU_VR_READY0.576––
CPU_ZVM_L0.384––
CPUCORE_BOOT10.608––
CPUCORE_BOOT20.606––
CPUCORE_BP10.608––
CPUCORE_BP20.606––
CPUCORE_FCCM0.56––
CPUCORE_ISEN10.58––
CPUCORE_ISEN20.58––
CPUCORE_ISNS1_N0.0051.500–
CPUCORE_ISNS1_P0.0051.500–
CPUCORE_ISNS2_N0.0051.500–
CPUCORE_ISNS2_P0.0051.500–
CPUCORE_ISUMN0.007–6.400R
CPUCORE_ISUMN_R0.29––
CPUCORE_ISUMP0.29––
CPUCORE_PHASE10.006––
CPUCORE_PHASE20.006––
CPUCORE_PSYS0.58––
CPUCORE_PWM10.57––
CPUCORE_SW10.0051.5004.400R
CPUCORE_SW1_SNUBOL––
CPUCORE_SW20.0051.5004.400R
CPUCORE_SW2_SNUBOL––
CPUGT_BOOT10.606––
CPUGT_BOOT20.609––
CPUGT_BOOT30.607––
CPUGT_BP10.607––
CPUGT_BP20.610––
CPUGT_BP30.608––
CPUGT_ISEN10.626––
CPUGT_ISEN20.627––
CPUGT_ISEN30.625––
CPUGT_ISNS_NOL––
CPUGT_ISNS_POL––
CPUGT_ISNS_R_NOL––
CPUGT_ISNS_R_POL––
CPUGT_ISNS1_N0.0051.500–
CPUGT_ISNS1_P0.0051.500–
CPUGT_ISNS2_N0.0051.5004.600R
CPUGT_ISNS2_P0.0051.5004.600R
CPUGT_ISNS3_N0.0051.500–
CPUGT_ISNS3_P0.0051.500–
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN0.002–0.200R
CPUGT_ISUMN_R0.340––
CPUGT_ISUMP0.341––
CPUGT_PHASE20.005–4.900R
CPUGT_PHASE30.005––
CPUGT_PWM10.613––
CPUGT_PWM20.614––
CPUGT_SW_SNUBOL––
CPUGT_SW10.005–4.600R
CPUGT_SW1_SNUBOL––
CPUGT_SW20.0051.5004.600R
CPUGT_SW2_SNUBOL––
CPUGT_SW30.0051.5004.600R
CPUGT3_DRVHOL––
CPUGTVSENSE_IN0.005––
CPUHI_IOUT0.720––
CPUSA_BOOTSA0.607––
CPUSA_BPSA0.607––
CPUSA_DRVHOL––
CPUSA_FCCM0.615––
CPUSA_GL00.440––
CPUSA_ISNS_N0.037–36.300R
CPUSA_ISNS_P0.037–36.400R
CPUSA_ISNS_R_N0.0241.15022.100R
CPUSA_ISNS_R_P0.0241.15022.100R
CPUSA_ISUMN0.026–24.000R
CPUSA_ISUMN_R0.490––
CPUSA_ISUMP0.575––
CPUSA_PHASESA0.024––
CPUSA_PWM0.614––
CPUSA_SW_SNUBOL––
CPUSAVSENSE_IN0.029–29.000R
CPUTHMSNS_ADDR_SEL0.646––
CPUTHMSNS_D1_N0.001–0.600R
CPUTHMSNS_D1_P0.646––
CPUTHMSNS_D2_N0.003–1.200R
CPUTHMSNS_D2_P0.645––
CPUTHMSNS_D3_N0.002–0.030R
CPUTHMSNS_D3_P0.644––
CPUTHMSNS_D4_N0.002–0.040R
CPUTHMSNS_D4_P0.643––
CPUVCCIO_IOUTOL––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS_R_NOL––
CPUVR_ISNS_R_POL––
CPUVR_ISUM_IOUTOL––
CPUVR_SWSA0.0241.15022.100R
CPUVR_VIDALERT_L_R0.294––
CPUVR_VIDSCLK_R0.304––
CPUVR_VIDSOUT_R0.265––
CPUVSENSE_IN0.007–8.100R
CSI2_COMP0.101––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S0I3OL––
DBGLED_S0I3_DOL––
DBGLED_S3OL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DDI1_MUX_EN0.687––
DDI1_MUX_SEL_INV0.646––
DDI2_MUX_EN0.696––
DDRREG_VTTSNS0.153––
DEBUG_JTAG_SOC_TDI0.465––
DEBUG_JTAG_SOC_TDO0.464––
DFR_DISP_INT0.49––
DFR_DISP_RESET_L0.49––
DFR_DISP_TE0.49––
DFR_DISP_VSYNCOL––
DFR_PWR_EN0.467––
DFR_PWR_EN_R0.551––
DFR_TOUCH_CLK32K_RESET_L0.50––
DFR_TOUCH_INT_L0.50––
DFR_TOUCH_LID_OPEN_LOL––
DFR_TOUCH_RESET_L0.48––
DFUMUX_SELOL––
DP_DDI1_ML_C_N<0>0.277––
DP_DDI1_ML_C_P<0>0.275––
DP_DDPB_HPD0.605––
DP_DDPC_HPD0.650––
DP_INT_HPDOL––
DP_T_SNK0_AUXCH_C_N0.494––
DP_T_SNK0_AUXCH_C_P0.671––
DP_T_SNK0_AUXCH_N0.420––
DP_T_SNK0_AUXCH_P0.440––
DP_T_SNK0_HPD0.582––
DP_T_SNK1_AUXCH_C_N0.495––
DP_T_SNK1_AUXCH_C_P0.670––
DP_T_SNK1_AUXCH_N0.415––
DP_T_SNK1_AUXCH_P0.440––
DP_T_SNK1_HPD0.545––
DP_TA_HPD0.568––
DP_TB_HPD0.54––
DP_X_SNK0_AUXCH_C_N0.495––
DP_X_SNK0_AUXCH_C_P0.502––
DP_X_SNK0_AUXCH_N0.430––
DP_X_SNK0_AUXCH_P0.466––
DP_X_SNK0_HPD0.575––
DP_X_SNK1_AUXCH_C_N0.492––
DP_X_SNK1_AUXCH_C_P0.495––
DP_X_SNK1_AUXCH_N0.429––
DP_X_SNK1_AUXCH_P0.455––
DP_X_SNK1_HPD0.578––
DP_XA_HPD0.614––
DP_XB_HPD0.55––
EADC1_LCDBKLT_ISENSEOL––
EADC1_P3V3RTC_HI_ISENSEOL––
EADC1_PP3V3_KBD_ISENSEOL––
EADC1_PP3V3S0_DFR_ISENSEOL––
EADC1_PP5V_TPAD_ISENSEOL––
EADC1_SPKRAMPL_ISENSEOL––
EADC1_TBT_ISENSEOL––
EADC1_TBT_T_ISENSEOL––
EADC2_AD0OL––
EADC2_BMON_DISCRETE_ISENSEOL––
EADC2_CAMERA_ISENSEOL––
EADC2_DDR1V8_ISENSEOL––
EADC2_KBBLT_ISENSEOL––
EADC2_MESA_ISENSEOL––
EADC2_PP3V3_TPAD_ISENSEOL––
EADC2_PP5V_LCD_ISENSEOL––
EADC2_SPKRAMPR_ISENSEOL––
EDP_BKLT_EN0.563––
EDP_COMP0.151––
EDP_INT_AUX_N0.271––
EDP_INT_AUX_P0.274––
EDP_INT_ML_N<0>0.274––
EDP_INT_ML_N<1>0.274––
EDP_INT_ML_N<2>0.276––
EDP_INT_ML_N<3>0.273––
EDP_INT_ML_P<0>0.274––
EDP_INT_ML_P<1>0.275––
EDP_INT_ML_P<2>0.275––
EDP_INT_ML_P<3>0.273––
EDP_PANEL_PWR_BUF_EN0.617––
EDP_PANEL_PWR_DLY_EN0.612––
EDP_PANEL_PWR_EN0.560––
EMMC_RCOMP0.203––
ENET_CLKREQ_L0.463––
ESD_GND0.000––
ESPI_CLK60M0.460––
ESPI_CLK60M_DBG0.504––
ESPI_CLK60M_R0.475––
ESPI_CS_L0.457––
ESPI_IO_PCH<0>0.485––
ESPI_IO_PCH<1>0.490––
ESPI_IO_PCH<2>0.495––
ESPI_IO_PCH<3>0.483––
ESPI_IO_R<0>0.458––
ESPI_IO_R<1>0.458––
ESPI_IO_R<2>0.457––
ESPI_IO_R<3>0.456––
ESPI_IO<0>0.473––
ESPI_IO<1>0.476––
ESPI_IO<2>0.473––
ESPI_IO<3>0.471––
FAN_LT_PWM0.839––
FAN_LT_TACHOL––
FAN_RT_PWM0.841––
FAN_RT_TACHOL––
FB_A_CPUGT0.605––
FB_A_GT_R1.609––
FB_A_GT_RC1.610––
FB_B_CORE_R1.610––
FB_B_CORE_RC1.327––
FB_B_CPUCORE0.55––
FB_C_CPUSA0.603––
FB_C_SA_RC1.167––
FB_CORE_R0.007–6.200R
FB_GT_R0.007–5.800R
FB_SA_R0.026–24.900R
GT_ISUMN_R1.017––
HS_3V3RTC_IOUTOL––
HS_MIC_N0.632––
HS_MIC_P0.633––
HS_OTHER3V3_IOUT0.718––
HS_OTHER5V_IOUT0.720––
I2C_ALS_SCL0.459––
I2C_ALS_SDA0.457––
I2C_BATT_SCL_R0.471––
I2C_BATT_SDA_R0.468––
I2C_BKLT_SCL0.555––
I2C_BKLT_SDA0.556––
I2C_CODEC_SCL0.458––
I2C_CODEC_SDA0.457––
I2C_DFR_SCL0.467––
I2C_DFR_SCL_R0.50––
I2C_DFR_SDA0.466––
I2C_DFR_SDA_R0.50––
I2C_DISP_LS_EN0.716––
I2C_DISP_SCL0.458––
I2C_DISP_SDA0.457––
I2C_FTCAM_ISOL_SCL0.631––
I2C_FTCAM_ISOL_SDA0.652––
I2C_FTCAM_SCL0.455––
I2C_FTCAM_SDA0.454––
I2C_KBD_SCLOL––
I2C_KBD_SDAOL––
I2C_PWR_SCL0.464––
I2C_PWR_SDA0.461––
I2C_SEP_SCL0.44––
I2C_SEP_SDA0.44––
I2C_SNS_G3S_SCL0.464––
I2C_SNS_G3S_SDA0.465––
I2C_SNS0_S0_SCL0.458––
I2C_SNS0_S0_SDA0.458––
I2C_SNS1_S0_SCL0.460––
I2C_SNS1_S0_SDA0.465––
I2C_SPKRAMP_L_SCL0.388––
I2C_SPKRAMP_L_SDA0.387––
I2C_SPKRAMP_R_SCL0.386––
I2C_SPKRAMP_R_SDA0.385––
I2C_SSD_SCL0.463––
I2C_SSD_SDA0.463––
I2C_TBT_T_SCL0.540––
I2C_TBT_T_SDA0.540––
I2C_TBT_TA_INT_L0.689––
I2C_TBT_TB_INT_L0.681––
I2C_TBT_X_SCL0.54––
I2C_TBT_X_SDA0.54––
I2C_TBT_XA_INT_L0.707––
I2C_TBT_XB_INT_L0.719––
I2C_TCON_SCL0.613––
I2C_TCON_SDA0.613––
I2C_TPAD_3V3_SCL1.000––
I2C_TPAD_3V3_SCL_R0.976––
I2C_TPAD_3V3_SDA1.027––
I2C_TPAD_3V3_SDA_R0.996––
I2C_TPAD_SDA_R0.496––
I2C_UPC_SCL0.466––
I2C_UPC_SDA0.463––
I2C_UPC_T_SCL20.505––
I2C_UPC_T_SDA20.500––
I2C_UPC_TA_DBG_CTL_SCL0.738––
I2C_UPC_TA_DBG_CTL_SDA0.742––
I2C_UPC_TB_DBG_CTL_SCL0.74––
I2C_UPC_TB_DBG_CTL_SDA0.74––
I2C_UPC_X_SCL20.506––
I2C_UPC_X_SDA20.499––
I2C_UPC_XA_DBG_CTL_SCL0.545––
I2C_UPC_XA_DBG_CTL_SDA0.631––
I2C_UPC_XB_DBG_CTL_SCL0.74––
I2C_UPC_XB_DBG_CTL_SDA0.74––
I2S_CODEC_BCLK0.465––
I2S_CODEC_BCLK_R0.455––
I2S_CODEC_D2R0.462––
I2S_CODEC_LRCLK0.458––
I2S_CODEC_LRCLK_R0.470––
I2S_CODEC_R2D0.450––
I2S_CODEC_R2D_R0.446––
I2S_SPKRAMP_L_BCLK0.388––
I2S_SPKRAMP_L_BCLK_R0.405––
I2S_SPKRAMP_L_D2R0.379––
I2S_SPKRAMP_L_D2R_R10.389––
I2S_SPKRAMP_L_D2R_R20.387––
I2S_SPKRAMP_L_LRCLK0.405––
I2S_SPKRAMP_L_LRCLK_R0.387––
I2S_SPKRAMP_L_R2D0.388––
I2S_SPKRAMP_L_R2D_R0.405––
I2S_SPKRAMP_R_BCLK0.391––
I2S_SPKRAMP_R_BCLK_R0.404––
I2S_SPKRAMP_R_D2R0.465––
I2S_SPKRAMP_R_D2R_R10.388––
I2S_SPKRAMP_R_D2R_R20.387––
I2S_SPKRAMP_R_LRCLK0.403––
I2S_SPKRAMP_R_LRCLK_R0.386––
I2S_SPKRAMP_R_R2D0.390––
I2S_SPKRAMP_R_R2D_R0.404––
IMON_A_CPUGT0.625––
IMON_B_CPUCORE0.58––
IMON_C_CPUSA0.626––
IPD_LID_OPEN0.721––
IPD_LID_OPEN_ROL––
ISNS_ALSCAM_IOUTOL––
ISNS_ALSCAM_NOL––
ISNS_ALSCAM_POL––
ISNS_CALPE_IOUTOL––
ISNS_CALPE_NOL––
ISNS_CALPE_POL––
ISNS_CPUDDR_IOUTOL––
ISNS_CPUDDR_N0.2161.200–
ISNS_CPUDDR_P0.2161.200–
ISNS_CPUEDRAM_IOUTOL––
ISNS_CPUEDRAM_N0.055–47.500R
ISNS_CPUEDRAM_P0.056–49.200R
ISNS_CPUREG_IOUTOL––
ISNS_CPUREG_NOL––
ISNS_CPUREG_POL––
ISNS_CPUSA_IOUTOL––
ISNS_CPUVCCIO_N0.140––
ISNS_CPUVCCIO_P0.140––
ISNS_CPUVDDQ_NOL––
ISNS_CPUVDDQ_POL––
ISNS_DDR_IOUT0.716––
ISNS_HS_3V3RTC_NOL––
ISNS_HS_3V3RTC_POL––
ISNS_HS_COMPUTING_N0.46013.100–
ISNS_HS_COMPUTING_P0.46013.100–
ISNS_HS_OTHER3V3_N0.46013.100–
ISNS_HS_OTHER3V3_P0.46013.100–
ISNS_HS_OTHER5V_N0.46013.100–
ISNS_HS_OTHER5V_P0.46013.100–
ISNS_KBBLT_IOUTOL––
ISNS_KBBLT_NOL––
ISNS_KBBLT_POL––
ISNS_LCDBKLT_N0.460––
ISNS_LCDBKLT_P0.460––
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_LPDDR_NOL––
ISNS_LPDDR_POL––
ISNS_MESA_IOUTOL––
ISNS_MESA_NOL––
ISNS_MESA_POL––
ISNS_OCARINA_N0.398––
ISNS_OCARINA_P0.398––
ISNS_PP1V8_WLANBT_IOUTOL––
ISNS_PP1V8_WLANBT_NOL––
ISNS_PP1V8_WLANBT_POL––
ISNS_PP3V3_KBD_IOUTOL––
ISNS_PP3V3_KBD_NOL––
ISNS_PP3V3_KBD_POL––
ISNS_PP3V3_TPAD_IOUTOL––
ISNS_PP3V3_TPAD_NOL––
ISNS_PP3V3_TPAD_POL––
ISNS_PP3V3S0_IOUTOL––
ISNS_PP3V3S0_NOL––
ISNS_PP3V3S0_POL––
ISNS_PP3V3S4_WLAN_IOUTOL––
ISNS_PP3V3S4_WLAN_NOL––
ISNS_PP3V3S4_WLAN_POL––
ISNS_PP3V3S4_WLAN_R_NOL––
ISNS_PP3V3S4_WLAN_R_POL––
ISNS_PP5V_LCD_IOUTOL––
ISNS_PP5V_TPAD_IOUTOL––
ISNS_PP5V_TPAD_NOL––
ISNS_PP5V_TPAD_POL––
ISNS_SPKRAMP_LEFT_NOL––
ISNS_SPKRAMP_LEFT_POL––
ISNS_SPKRAMP_RIGHT_NOL––
ISNS_SPKRAMP_RIGHT_POL––
ISNS_SPKRAMPL_IOUTOL––
ISNS_SPKRAMPR_IOUTOL––
ISNS_SSDNAND_N0.46013.100–
ISNS_SSDNAND_P0.46013.100–
ISNS_TBT_IOUTOL––
ISNS_TBT_NOL––
ISNS_TBT_POL––
ISNS_TBT_T_IOUTOL––
ISNS_TBT_T_NOL––
ISNS_TBT_T_POL––
ISNS_WLAN_OPOL––
ITP_PMODE0.382––
JTAG_ISP_TCK0.581––
JTAG_ISP_TDI0.581––
JTAG_ISP_TDO0.580––
JTAG_TBT_T_TMS0.605––
JTAG_TBT_X_TMS0.609––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_INT_LOL––
L83_FILT0.800––
L83_FLYC0.393––
L83_FLYN0.749––
L83_FLYP0.406––
L83_HSBIAS_FILT0.720––
L83_HSBIAS_FILT_REF0.641––
L83_SDOUT0.487––
L83_VCP_FILT_GND0.000––
L83_VCP_FILTN0.762––
L83_VCP_FILTP0.395––
LCD_PWR_SLEW0.645––
LCD_PWR_SLEW_3V30.716––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.734––
LCDBKLT_FET_DRV0.543––
LCDBKLT_FET_DRV_R0.584––
LCDBKLT_SW0.452––
LCDBKLT_TB_XWR1.180––
LDO_RTC0.377––
LID_OPEN_LEFT0.457––
LID_OPEN_RIGHT0.460––
MEM_A_ZQ<0>0.245––
MEM_A_ZQ<1>0.245––
MEM_A_ZQ<2>0.246––
MEM_A_ZQ<3>0.245––
MEM_B_ZQ<0>0.246––
MEM_B_ZQ<1>0.245––
MEM_B_ZQ<2>0.245––
MEM_B_ZQ<3>0.245––
MEM_VREFCA_RC0.026–25.300R
MEM_VREFDQ_B_RC0.027–25.600R
MEMVTT_EN0.534––
MEMVTT_EN_R0.534––
MESA_BOOST_EN0.559––
MESA_BOOST_EN_CONNOL––
MESA_INT0.469––
MESA_INT_CONNOL––
MESA_PWR_EN0.459––
MIPI_DFR_CLK_FILT_CONN_N0.777––
MIPI_DFR_CLK_FILT_CONN_P0.774––
MIPI_DFR_CLK_N0.775––
MIPI_DFR_CLK_P0.772––
MIPI_DFR_DATA_FILT_CONN_N0.776––
MIPI_DFR_DATA_FILT_CONN_P0.769––
MIPI_DFR_DATA_N0.774––
MIPI_DFR_DATA_P0.766––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_N0.770––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_P0.770––
MIPI_FTCAM_CLK_ISOL_N0.767––
MIPI_FTCAM_CLK_ISOL_P0.767––
MIPI_FTCAM_CLK_N0.532––
MIPI_FTCAM_CLK_P0.550––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_N<0>0.764––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_P<0>0.719––
MIPI_FTCAM_DATA_ISOL_N<0>0.761––
MIPI_FTCAM_DATA_ISOL_P<0>0.718––
MIPI_FTCAM_DATA_N<0>0.521––
MIPI_FTCAM_DATA_P<0>0.538––
MLB_RAMCFG00.748––
MLB_RAMCFG10.725––
MLB_RAMCFG20.764––
MLB_RAMCFG30.766––
MLB_RAMCFG40.766––
NTC_A_CPUGT0.627––
NTC_A_CPUGT_RN0.000––
NTC_A_CPUGT_RPOL––
NTC_B_CPUCORE0.58––
NTC_B_CPUCORE_RN0.002––
NTC_B_CPUCORE_RPOL––
OPC_RCOMP0.052–50.000R
OPCE_RCOMP0.052–50.100R
P0V8SLPDDR_FB0.239––
P0V8SLPDDR_FB_R0.241––
P0V8SLPDDR_SW00.1400.800–
P0V8SLPDDR_SW10.1400.800–
P0V9_LX0_SSD00.3330.900–
P0V9_LX1_SSD00.3330.900–
P0V9_TBT_T_SVR_AGND0.000–0.300R
P0V9_TBT_X_SVR_AGND0.000––
P0V9SLPDDR_SW00.1060.900–
P0V9SLPDDR_SW10.1060.90085.100R
P1V1_SLPDDR_SOCFET_EN0.5711.800–
P1V1_SLPDDR_SOCFET_EN_ROL––
P1V1SLPDDR_RAMP0.616––
P1V1SLPS2R_FB0.376––
P1V1SLPS2R_SW00.3851.100–
P1V1SLPS2R_SW10.3851.100–
P1V2_BOOT_RC0.636––
P1V2_DRVH0.712––
P1V2_DRVH_R0.713––
P1V2_DRVL0.461––
P1V2_DRVL_R0.463––
P1V2_LL_SNUBOL––
P1V2_PHASE0.2161.200–
P1V2_SNS0.229––
P1V2_SNS_R0.218––
P1V2_SW0.224––
P1V2_VBST0.634––
P1V2_WLANBT_VLX0.2991.200–
P1V2REG_AGND0.002–0.400R
P1V2REG_MODE0.542––
P1V2REG_TRIP0.754––
P1V2REG_VREF0.647––
P1V2REG_VREF_ROL––
P1V2S0SW_FET_EN0.561––
P1V5_WLANBT_VLX0.3241.500–
P1V8_DFR_ROL––
P1V8_G3S_EN_ROL––
P1V8_LX0_SSD00.3611.800–
P1V8G3S_EN0.566––
P1V8G3S_SS0.630––
P1V8SLPS2R_SW00.4101.800–
P1VPRIM_FB0.175––
P1VPRIM_FB_R0.175––
P1VPRIM_SW00.2011.000–
P1VPRIM_SW10.2011.000–
P2V7_SW1_TPS62180_SSD00.3402.700–
P2V7_SW2_TPS62180_SSD00.3402.700–
P3V3_G3H_RTC_DEBUG_LED_ROL––
P3V3_TBT_T_SX_R0.570––
P3V3_TBT_X_SX_R0.577––
P3V3G3H_COMP20.68––
P3V3G3H_COMP2_ROL––
P3V3G3H_CSN20.41––
P3V3G3H_CSP21.290––
P3V3G3H_CSP2_R0.440––
P3V3G3H_DRVH0.91––
P3V3G3H_DRVL0.54––
P3V3G3H_DRVL_R0.558––
P3V3G3H_EN_R0.52––
P3V3G3H_RF0.52––
P3V3G3H_SNUBROL––
P3V3G3H_SW0.41––
P3V3G3H_TG1.020––
P3V3G3H_VBST0.55––
P3V3G3H_VBST_R0.636––
P3V3G3H_VFB20.52––
P3V3G3H_VFB2_R0.440––
P3V3G3H_VFB2_RR1.366––
P3V3G3H_VSW0.4303.300–
P3V3G3HRTC_FB1.427––
P3V3G3HRTC_FB_R0.414––
P3V3G3HRTC_PGOOD0.702––
P3V3G3HRTC_PHASE10.3993.300–
P3V3G3HRTC_PHASE20.3993.300–
P3V3G3HRTC_RA_R0.413––
P3V3G3HRTC_SS0.549––
P3V3G3S_EN0.572––
P3V3G3S_SS0.718––
P3V3MAIN_PGOOD0.52––
P3V3TBT_T_RAMP0.716––
P5V_P3V3G3H_LDO_EN0.52––
P5V_S4SW_SNS_FET_RAMPOL––
P5VG3S_COMP10.68––
P5VG3S_COMP1_ROL––
P5VG3S_CSN10.40––
P5VG3S_CSP11.007––
P5VG3S_CSP1_R0.432––
P5VG3S_DRVH0.91––
P5VG3S_DRVL0.54––
P5VG3S_EN0.594––
P5VG3S_EN_R0.52––
P5VG3S_PGOOD0.52––
P5VG3S_SNUBROL––
P5VG3S_SW0.40––
P5VG3S_VBST0.56––
P5VG3S_VBST_R0.637––
P5VG3S_VFB10.51––
P5VG3S_VFB1_R0.432––
P5VG3S_VFB1_RR0.631––
P5VG3S_VSW0.4335.000–
P5VP3V3_SKIPSEL0.45––
P5VP3V3_VREF20.45––
P5VP3V3_VREG30.47––
P5VUSBC_T_AGND0.000––
P5VUSBC_T_BOOT_RC0.612––
P5VUSBC_T_DRVH0.988––
P5VUSBC_T_DRVH_R0.988––
P5VUSBC_T_FSEL0.559––
P5VUSBC_T_LL0.5055.000–
P5VUSBC_T_NEG0.5055.000–
P5VUSBC_T_OCSET0.558––
P5VUSBC_T_POS0.5055.000–
P5VUSBC_T_R0.5055.000–
P5VUSBC_T_RTN_DIV0.550––
P5VUSBC_T_RTN_DIV_R––0.500R
P5VUSBC_T_SENSE_DIV0.552––
P5VUSBC_T_SENSE_DIV_R0.508––
P5VUSBC_T_SET_ROL––
P5VUSBC_T_SET00.559––
P5VUSBC_T_SET10.558––
P5VUSBC_T_SREF0.558––
P5VUSBC_T_VBST0.609––
P5VUSBC_T_VO0.557––
P5VUSBC_X_AGND0.000––
P5VUSBC_X_BOOT_RC0.609––
P5VUSBC_X_DRVH0.992––
P5VUSBC_X_FSEL0.561––
P5VUSBC_X_LL0.5035.000–
P5VUSBC_X_NEG0.503––
P5VUSBC_X_OCSET0.561––
P5VUSBC_X_PGOOD0.561––
P5VUSBC_X_POS0.503––
P5VUSBC_X_R0.5035.000–
P5VUSBC_X_RTN_DIV0.556––
P5VUSBC_X_RTN_DIV_XW0.002–0.500R
P5VUSBC_X_SENSE_DIV0.554––
P5VUSBC_X_SET_ROL––
P5VUSBC_X_SET00.561––
P5VUSBC_X_SET10.560––
P5VUSBC_X_SREF0.558––
P5VUSBC_X_VBST0.611––
P5VUSBC_X_VO0.558––
PANEL_P3V3_EN0.568––
PANEL_P3V3_EN_D0.735––
PANEL_P5V_EN0.570––
PANEL_P5V_EN_D1.020––
PBUS_DIVIDER0.708––
PBUS_DIVIDER_OUT0.670––
PBUS_DIVIDER_REF0.677––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.46013.100–
PBUSVSENS_EN_L0.497––
PBUSVSENS_EN_L_DIVOL––
PCH_BATLOW_L0.822––
PCH_CLK24M_XTALIN0.840––
PCH_CLK24M_XTALOUT0.836––
PCH_CLK24M_XTALOUT_R0.837––
PCH_CLKIN_XTAL0.003–0.400R
PCH_DDPB_CTRLDATA0.798––
PCH_DDPC_CTRLDATA0.799––
PCH_DIFFCLK_BIASREF0.062–60.400R
PCH_GPP_A0_PU0.822––
PCH_HSIO_PWR_EN0.818––
PCH_INTRUDER_L0.848––
PCH_JTAGX0.059–59.700R
PCH_LAN_WAKE_L0.824––
PCH_OPIRCOMP0.052–50.100R
PCH_PCIE_CLK100M_WLAN_N0.333––
PCH_PCIE_CLK100M_WLAN_P0.333––
PCH_PCIE_RCOMP_N0.313––
PCH_PCIE_RCOMP_P0.314––
PCH_PWRBTN_L0.769––
PCH_RTC_RESET_L0.7693.000–
PCH_SOC_SYNC0.460––
PCH_STRP_CNV_DISABLE0.542––
PCH_STRP_ESPI0.807––
PCH_STRP_GPD70.821––
PCH_STRP_JTAGODTDIS0.811––
PCH_STRP_NO_REBOOT0.806––
PCH_STRP_SPIROM_SAF0.807––
PCH_STRP_XTAL_24MHZ0.806––
PCH_SWD_SOC_CLK0.583––
PCH_SWD_SOC_IO0.565––
PCH_UART_BT_CTS_L0.702––
PCH_UART_BT_D2R0.705––
PCH_UART_BT_R2D0.705––
PCH_UART_BT_RTS_L0.700––
PCH_UART_DEBUG_D2R0.772––
PCH_UART_DEBUG_R2D0.773––
PCH_UART2_CTS_L0.822––
PCH_USB2_COMP0.115––
PCH_USB2_VBUSSENSE0.782––
PCH_WLAN_CLKREQ_L0.816––
PCH_WLAN_PERST_L0.828––
PCIE_CLK100M_SOC_N0.312––
PCIE_CLK100M_SOC_P0.312––
PCIE_CLK100M_SSD0_01_N0.121––
PCIE_CLK100M_SSD0_01_P0.120––
PCIE_CLK100M_SSD0_23_N0.120––
PCIE_CLK100M_SSD0_23_P0.120––
PCIE_CLK100M_TBT_T_N0.332––
PCIE_CLK100M_TBT_T_P0.334––
PCIE_CLK100M_TBT_X_N0.335––
PCIE_CLK100M_TBT_X_P0.337––
PCIE_SSD0_D2R_N<0>0.382––
PCIE_SSD0_D2R_P<0>0.379––
PCIE_TBT_T_D2R_N<0>0.341––
PCIE_TBT_T_D2R_P<0>0.340––
PCIE_TBT_X_D2R_N<0>0.339––
PCIE_TBT_X_D2R_P<0>0.336––
PCIE_WAKE_L0.819––
PDM_DMIC_CLK00.493––
PDM_DMIC_CLK0_R0.465––
PDM_DMIC_CLK10.494––
PDM_DMIC_CLK1_R0.464––
PDM_DMIC_DATA00.455––
PDM_DMIC_DATA0_RR0.470––
PDM_DMIC_DATA0_UNSEC0.538––
PDM_DMIC_DATA10.457––
PDM_DMIC_DATA1_RR0.477––
PDM_DMIC_DATA1_UNSEC0.541––
PHV_INT_TA_G3H0.461––
PHV_INT_TB_G3H0.61––
PHV_INT_XA_G3H0.612––
PHV_INT_XB_G3H0.61––
PLT_RST_3V3_L0.693––
PLT_RST_L0.667––
PM_MEMVTT_EN0.391––
PM_OPC_ZVM_L0.588––
PM_PCH_PWROK0.510––
PM_PCH_SYS_PWROK0.583––
PM_RSMRST_L0.484––
PM_SLP_S0_3V3_L0.721––
PM_SLP_S0_L0.470––
PM_SLP_S0_R_LOL––
PM_SLP_S3_L0.579––
PM_SLP_S4_L0.820––
PM_SLP_S5_L0.821––
PM_SLP_SUS_L0.819––
PM_SLP_TIEOFF0.697––
PM_SYSRST_L0.820––
PM_SYSRST_R_L0.586––
PM_THRMTRIP_L0.278––
PMU_ACTIVE_READY0.4701.800–
PMU_ACTIVE_READY_ROL––
PMU_CLK32K_PCH0.812––
PMU_CLK32K_PCH_1V00.865––
PMU_CLK32K_PCH_R0.778––
PMU_CLK32K_SOC0.470––
PMU_CLK32K_SOC_R0.501––
PMU_COLD_RESET_L0.4591.800–
PMU_CPU_ISENSE0.592––
PMU_CPU_VSENSE0.591––
PMU_CPUDDR_ISENSE0.592––
PMU_CPUEDRAM_ISENSE0.594––
PMU_CPUGT_ISENSE0.591––
PMU_CPUGT_VSENSE0.592––
PMU_CPUP5VREG_ISENSE0.593––
PMU_CPUSA_ISENSE0.593––
PMU_CPUSA_VSENSE0.591––
PMU_CPUVCCIO_ISENSE0.593––
PMU_DDR1V2_ISENSE0.587––
PMU_DROOP_L0.466––
PMU_FORCE_DFU0.772––
PMU_IREF0.763––
PMU_LCDPANEL_ISENSE0.593––
PMU_OCARINA_ISENSE0.589––
PMU_ONOFF_L0.6993.300–
PMU_ONOFF_R_L_CONN0.703––
PMU_OTHER3V3_HI_ISENSE0.589––
PMU_OTHER5V_HI_ISENSE0.590––
PMU_PVDDMAIN_EN0.776––
PMU_RSLOC_RST_L0.703––
PMU_SSDNAND_ISENSE0.588––
PMU_SYS_ALIVE0.4091.800–
PMU_VDD_HI0.665––
PMU_VREF–1.100–
PMU_XTAL10.801––
PMU_XTAL1_R0.802––
PMU_XTAL20.801––
PP0V6_S0_DDRVTT0.151––
PP0V6_S3_MEM_VREFCA_A0.380––
PP0V6_S3_MEM_VREFDQ_A0.381––
PP0V6_S3_MEM_VREFDQ_B0.379––
PP0V8_SLPS2R0.1910.792–
PP0V9_SLPDDR0.1060.90085.100R
PP0V9_SLPDDR_SOC_PCIEREFBUF0.089–87.100R
PP0V9_SSD00.3330.900–
PP0V9_SSD0_FB_DIS0.325––
PP0V9_TBT_T_LC0.365––
PP0V9_TBT_T_LVR0.487––
PP0V9_TBT_T_PCIE0.327––
PP0V9_TBT_T_SVR0.3220.900–
PP0V9_TBT_X_LC0.376––
PP0V9_TBT_X_LVR0.493––
PP0V9_TBT_X_PCIE0.340––
PP0V9_TBT_X_SVR0.3530.900–
PP0V82_SLPDDR0.1400.800–
PP0V95_S0_CPUVCCIO_REG_R0.0800.950123.700R
PP1V_PRIM0.2011.000–
PP1V_S0SW0.229––
PP1V_S30.238––
PP1V1_SLPDDR0.3561.100–
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.357––
PP1V1_SLPDDR_SOC_XTAL_F0.356––
PP1V1_SLPS2R0.3851.100–
PP1V1_UPC_TA_LDO_BMC0.503––
PP1V1_UPC_TB_LDO_BMC0.481.100–
PP1V1_UPC_XA_LDO_BMC0.510––
PP1V1_UPC_XB_LDO_BMC0.48––
PP1V2_AWAKE0.5361.200–
PP1V2_AWAKE_SOC_PCIEPLL_F0.5351.200–
PP1V2_AWAKE_SOC_PCIEREFBUF_F0.536––
PP1V2_AWAKE_SOC_PLLCPU_F0.536––
PP1V2_AWAKE_SOC_PLLSOC_F0.536––
PP1V2_S0SW0.240––
PP1V2_S30.2161.200–
PP1V2_S3_CPUDDR0.218––
PP1V2_S3_REG_R0.2161.200–
PP1V2_WLANBT0.299––
PP1V2_WLANBT_C0.2991.200–
PP1V05_PRIM_PCH_VCCAPLL_AUD_F0.173––
PP1V05_PRIM_PCH_VCCAXTAL_F0.170––
PP1V05_PRIMSW_PCH_VCCAMPHYPLL_F0.172––
PP1V05_S5_PCH_VCCDSW0.490––
PP1V5_WLANBT0.320––
PP1V5_WLANBT_C0.3241.500–
PP1V8_ACCEL_FILT0.337––
PP1V8_AWAKE0.331.800–
PP1V8_AWAKE_SOC_FMON_RC0.399––
PP1V8_AWAKE_SOC_TSADC_RC0.345––
PP1V8_CODEC0.332––
PP1V8_CODEC_VCP0.332––
PP1V8_CODEC_VCP_SEL0.335––
PP1V8_CODEC_VL0.331––
PP1V8_CODEC_VL_SEL0.335––
PP1V8_DFR0.53––
PP1V8_DMIC0.338––
PP1V8_G3S0.3301.800–
PP1V8_G3S_WLANBT_VDDIO0.336––
PP1V8_MESA0.519––
PP1V8_MESA_FILT_CONN0.518––
PP1V8_PRIM_PCH_VCCHDA_F0.324––
PP1V8_S0_CPUTHMSNS_TI_R0.322––
PP1V8_S0_TBTTHMSNS_R0.325––
PP1V8_S0_TBTTHMSNS_T_R0.321––
PP1V8_S30.4201.800–
PP1V8_S3_MEM0.4201.800–
PP1V8_S50.327––
PP1V8_SE_AVDD0.325––
PP1V8_SE_ESE0.367––
PP1V8_SLPS2R0.4101.800–
PP1V8_SLPS2R_PMUVDDGPIO–1.800–
PP1V8_SLPS2R_SOC_LPADC_RC0.429––
PP1V8_SLPS2R_SOC_LPOSC_RC0.448––
PP1V8_SSD00.3611.800–
PP1V8_SSD0_FB_DIS0.362––
PP1V8_UPC_TA_LDOA0.515––
PP1V8_UPC_TA_LDOD0.475––
PP1V8_UPC_TB_LDOA0.49––
PP1V8_UPC_TB_LDOD0.461.800–
PP1V8_UPC_XA_LDOA0.519––
PP1V8_UPC_XA_LDOD0.4820.470 TEST HAS––
PP1V8_UPC_XB_LDOA0.5271.800–
PP1V8_UPC_XB_LDOD0.561.800–
PP1V24_S5_PCH_VCCDPHY0.429––
PP1V25_SLPS2R_SMC_AVREF0.592––
PP2V5_ADC1_VREFOL––
PP2V5_ADC2_VREFOL––
PP2V7_NAND_SSD00.3402.700–
PP3V_G3H_RTC0.4473.000–
PP3V0_MESA0.551––
PP3V0_MESA_FILT_CONN-0.547––
PP3V3_AWAKE0.6503.300–
PP3V3_CODEC_LDO_IN0.397––
PP3V3_CODEC_VP0.398––
PP3V3_G3H0.4303.300–
PP3V3_G3H_DFR0.439––
PP3V3_G3H_DFUMUXOL––
PP3V3_G3H_MESA_SW0.403––
PP3V3_G3H_PMU_VDDMAIN0.4363.300–
PP3V3_G3H_PMU_VINRTC_R0.4023.300–
PP3V3_G3H_RTC0.3273.300–
PP3V3_G3H_RTC_ISOL0.383.300–
PP3V3_G3H_RTC_MESA0.4033.300–
PP3V3_G3H_RTC_REG_R0.3993.300–
PP3V3_G3H_SSD00.3983.300–
PP3V3_G3HSW_DFR0.55––
PP3V3_G3S0.3003.300–
PP3V3_G3S_KBD0.297––
PP3V3_G3S_TPAD0.3003.300–
PP3V3_G3S_WLANBT0.300––
PP3V3_S0_TBT_T_ISNS_R0.530––
PP3V3_S0_TBT_X_ISNS_R0.542––
PP3V3_S0SW_LCD0.548––
PP3V3_S0SW_LCD_R0.548––
PP3V3_S4SW_SNS0.515––
PP3V3_S50.300––
PP3V3_TBT_T_ANA0.519––
PP3V3_TBT_T_ANA_PCIE0.500––
PP3V3_TBT_T_ANA_USB20.507––
PP3V3_TBT_T_F0.5203.300–
PP3V3_TBT_T_LC0.556––
PP3V3_TBT_T_S00.5203.300–
PP3V3_TBT_T_SX0.510––
PP3V3_TBT_X_ANA0.544––
PP3V3_TBT_X_ANA_PCIE0.521––
PP3V3_TBT_X_ANA_USB20.523––
PP3V3_TBT_X_F0.543––
PP3V3_TBT_X_LC0.577––
PP3V3_TBT_X_S00.543––
PP3V3_TBT_X_SX0.546––
PP3V3_UPC_TA_LDO0.4893.300–
PP3V3_UPC_TB_LDO0.493.300–
PP3V3_UPC_XA_LDO0.4903.300–
PP3V3_UPC_XB_LDO0.49––
PP4V7_SE_TVDD0.363––
PP5V_COREVR_VCC0.431––
PP5V_EADC1_AVDDOL––
PP5V_EADC2_AVDDOL––
PP5V_EDRAM_V5IN0.428––
PP5V_G3S0.4335.000–
PP5V_G3S_ALSCAM0.431––
PP5V_G3S_ALSCAM_F0.431––
PP5V_G3S_CPUREG0.430––
PP5V_G3S_DFR_FILT0.41––
PP5V_G3S_EDRAMPVCC0.434––
PP5V_G3S_EDRAMVCC0.434––
PP5V_G3S_FAN_CONN0.428––
PP5V_G3S_KBD0.427––
PP5V_G3S_TPAD0.428––
PP5V_G3S_TPAD_CONN0.428––
PP5V_G3S_VCCIOPVCC0.431––
PP5V_G3S_VCCIOVCC0.432––
PP5V_MAIN_VCCSA0.432––
PP5V_MAIN_VCORE10.433––
PP5V_MAIN_VCORE20.433––
PP5V_MAIN_VGT10.431––
PP5V_MAIN_VGT20.430––
PP5V_MAIN_VGT30.432––
PP5V_S0_BKLT_A0.433––
PP5V_S0_BKLT_D0.433––
PP5V_S0SW_LCD0.570––
PP5V_S0SW_LCD_ISNS_R0.570––
PP5V_S4_T_USBC0.5055.000–
PP5V_S4_WLAN_ISNS_DOL––
PP5V_S4_X_USBC0.503––
PP5V_S4SWOL––
PP5V_S4SW_ISNSOL––
PP5V_S5_LDO0.45––
PP5V_USBC_T_PVCC0.430––
PP5V_USBC_T_VCC0.430––
PP5V_USBC_X_PVCC0.435––
PP5V_USBC_X_VCC0.435––
PP16V0_MESA0.654––
PP16V0_MESA_FILT_CONN0.651––
PP17V0_MOJAVE_LDOIN0.593––
PP20V_USBC_TA_VBUS0.17020.000–
PP20V_USBC_TA_VBUS_F0.17020.000–
PP20V_USBC_TB_VBUS0.17020.000–
PP20V_USBC_TB_VBUS_F0.17020.000–
PP20V_USBC_XA_VBUS0.1720.000–
PP20V_USBC_XA_VBUS_F0.17020.000–
PP20V_USBC_XB_VBUS0.17020.000–
PP20V_USBC_XB_VBUS_F0.17020.000–
PPBUS_G3H0.46012.220–
PPBUS_G3H_SPKRAMP_LEFT0.46912.500–
PPBUS_G3H_SPKRAMP_RIGHT0.46013.100–
PPBUS_G3H_SSD00.46013.100–
PPBUS_HS_CPU0.46013.100–
PPDCIN_G3H0.55820.000–
PPDCIN_G3H_CHGR0.558––
PPDCPRTC_PCH0.680––
PPVBAT_G3H_CHGR_R0.46013.100–
PPVBAT_G3H_CHGR_REG0.46012.220–
PPVBAT_G3H_CONN1.566––
PPVCC_CPU_PH10.0051.5004.400R
PPVCC_CPU_PH20.0051.5004.400R
PPVCC_S0_CPU0.0051.5004.400R
PPVCCEDRAM_S0_CPU0.0501.00037.100R
PPVCCEDRAM_S0_REG_R0.0501.00034.300R
PPVCCGT_CPU_PH10.0051.5004.600R
PPVCCGT_CPU_PH20.0051.5004.600R
PPVCCGT_CPU_PH30.0051.5004.600R
PPVCCGT_S0_CPU0.0051.5004.600R
PPVCCIO_S0_CPU0.1270.950123.700
PPVCCSA_CPU_R0.0241.15022.100R
PPVCCSA_S0_CPU0.0241.15022.100R
PPVDDCPU_AWAKE0.0400.62526.500R
PPVDDCPUSRAM_AWAKE0.4980.800–
PPVIN_G3H_P3V3G3H0.46013.100–
PPVIN_G3H_P3V3G3HRTC0.46013.100–
PPVIN_G3H_P3V3G3HRTC_R0.46212.000–
PPVIN_G3H_P5VG3S0.46013.100–
PPVIN_RFLDO_WLANBT0.328––
PPVIN_RFLDO_WLANBT_C0.3301.800–
PPVIN_S0_CPUVR_VIN0.473––
PPVIN_S0SW_LCDBKLT0.82712.900–
PPVIN_S0SW_LCDBKLT_F0.460––
PPVIN_S0SW_LCDBKLT_R0.460––
PPVIN_S4_TPAD_FUSE0.46713.100–
PPVIN_SW_LCDBKLT_SW0.82712.900–
PPVOUT_S0_LCDBKLT1.18355.000–
PPVPCORE_S50.3151.000–
PPVTT_VTTREF0.497––
PROC_POPIRCOMP0.052–50.000R
PROG1_CPUCOREVR0.619––
PROG2_CPUCOREVR0.617––
PROG3_CPUCOREVR0.624––
PROG4_CPUCOREVR0.626––
PROG5_CPUCOREVR0.625––
PVCC_FB_N0.000–0.800R
PVCC_FB_P0.277––
PVCCCGT_PH1_AGND0.002–2.400R
PVCCCGT_PH2_AGND0.002–3.100R
PVCCCGT_PH3_AGND0.003–2.700R
PVCCCORE_PH1_AGND0.003––
PVCCCORE_PH2_AGND0.000–0.500R
PVCCCSA_AGND0.003––
PVCCEDRAM_BOOT_RC0.575––
PVCCEDRAM_DRVH0.608––
PVCCEDRAM_DRVH_R0.609––
PVCCEDRAM_DRVL0.471––
PVCCEDRAM_DRVL_R0.473––
PVCCEDRAM_LL0.041––
PVCCEDRAM_LL_SNUBOL––
PVCCEDRAM_PHASE0.0501.00034.300R
PVCCEDRAM_REFIN0.701––
PVCCEDRAM_VBST0.571––
PVCCEDRAMS0_AGND0.002–2.100R
PVCCEDRAMS0_CS_N0.0501.00041.500R
PVCCEDRAMS0_CS_P0.0501.00041.600R
PVCCEDRAMS0_EN0.778––
PVCCEDRAMS0_EN_FILT0.495––
PVCCEDRAMS0_EN_FILT_BUF0.530––
PVCCEDRAMS0_EN_R0.516––
PVCCEDRAMS0_FB0.552––
PVCCEDRAMS0_FSEL0.567––
PVCCEDRAMS0_OCSET0.559––
PVCCEDRAMS0_RTN0.555––
PVCCEDRAMS0_SREF0.564––
PVCCEDRAMS0_VO0.560––
PVCCEOPIO_EDRAM_PGOOD0.521––
PVCCIO_BOOT_RC0.591––
PVCCIO_DRVH0.583––
PVCCIO_DRVH_R0.583––
PVCCIO_DRVL0.472––
PVCCIO_DRVL_R0.473––
PVCCIO_EN0.762––
PVCCIO_LL0.131––
PVCCIO_LL_SNUBOL––
PVCCIO_PGOOD0.563––
PVCCIO_PHASE0.0800.950123.700R
PVCCIO_VBST0.590––
PVCCIOS0_AGND0.001––
PVCCIOS0_CS_N0.1270.950123.700
PVCCIOS0_CS_P0.1270.950123.700
PVCCIOS0_EN0.777––
PVCCIOS0_EN_FILT0.498––
PVCCIOS0_EN_FILT_BUF0.535––
PVCCIOS0_EN_R0.517––
PVCCIOS0_FB0.556––
PVCCIOS0_FSEL0.570––
PVCCIOS0_RTN0.554––
PVCCIOS0_SREF0.566––
PVCCIOS0_VO0.563––
PVCCOIOS0_OCSET0.563––
PVCCPCOREPRIM_FB_N0.001–1.000R
PVCCPCOREPRIM_FB_P0.275––
PVCCPCOREPRIM_SW00.3151.000–
PVCCPCOREPRIM_SW10.3151.000–
PVCCPLLOC_EN0.764––
PVDDCPUAWAKE_FB0.025–25.100R
PVDDCPUAWAKE_FB_R0.026–25.100R
PVDDCPUAWAKE_SW00.0400.62526.500R
PVDDCPUAWAKE_SW10.0400.62526.500R
PVDDCPUAWAKE_SW20.0400.62526.500R
PVDDCPUAWAKE_SW30.0400.62526.500R
PVDDCPUSRAMAWAKE_FB0.482––
PVDDCPUSRAMAWAKE_SW00.4980.800–
PVDDQ_EN0.559––
PVDDQ_EN_LEDOL––
PVDDQ_EN_R0.558––
PVDDQ_PGOOD0.568––
PVIN_RFLDO_WLANBT_VLX0.3301.800–
PVTT_VTTSNS0.153––
RIO_TBTTHMSNS_D1_N0.002–0.700R
RIO_TBTTHMSNS_D1_P0.662––
RTN_B_CPUCORE0.00––
SA_ISUMN_R1.030––
SAVE_BAT_G0.775––
SAVE_BAT_S1.567––
SAVE_TA_CC1_BOL––
SAVE_TA_CC1_G0.796––
SAVE_TA_CC1_ZOL––
SAVE_TA_CC2_BOL––
SAVE_TA_CC2_G0.794––
SAVE_TA_CC2_ZOL––
SAVE_TB_CC1_BOL––
SAVE_TB_CC1_G0.818––
SAVE_TB_CC1_ZOL––
SAVE_TB_CC2_BOL––
SAVE_TB_CC2_G0.818––
SAVE_TB_CC2_ZOL––
SAVE_XA_CC1_B2.400––
SAVE_XA_CC1_G0.829––
SAVE_XA_CC1_ZOL––
SAVE_XA_CC2_B2.400––
SAVE_XA_CC2_G0.834––
SAVE_XA_CC2_ZOL––
SAVE_XB_CC1_BOL––
SAVE_XB_CC1_G0.839––
SAVE_XB_CC1_ZOL––
SAVE_XB_CC2_BOL––
SAVE_XB_CC2_G0.843––
SAVE_XB_CC2_ZOL––
SD_RCOMP0.202––
SE_CTLR_FW_DWLD0.461––
SE_DEV_WAKE0.461––
SE_PWR_EN0.742––
SENSOR_PWR_EN0.722––
SEP_CAM_DISABLE_DFF_L0.712––
SEP_CAM_DISABLE_L0.461––
SEP_DISABLE_STROBE0.461––
SEP_DMIC_DISABLE_L0.461––
SEP_DMIC_DISABLE_OUT_L0.491––
SEP_SEL0.711––
SEP_WP0.71––
SMBUS_2_OEOL––
SMBUS_3V3_BATT_SCL1.006––
SMBUS_3V3_BATT_SDA1.000––
SMBUS_PCH_CLK0.802––
SMBUS_PCH_DATA0.793––
SMC_BMON_ISENSE0.814––
SMC_CALPE_ISENSE0.815––
SMC_CPU_HS_ISENSE0.812––
SMC_DCIN_ISENSE0.812––
SMC_DCIN_VSENSE0.809––
SMC_DEBUGPRT_RX0.478––
SMC_DEBUGPRT_TX0.476––
SMC_FAN_0_PWM0.468––
SMC_FAN_0_TACH0.467––
SMC_FAN_1_PWM0.467––
SMC_LID_LEFT0.640––
SMC_LID_RIGHT0.649––
SMC_PBUS_VSENSE0.809––
SMC_PCH_PWROK0.449––
SMC_PCH_SYS_PWROK0.448––
SMC_PECI_RX0.462––
SMC_PECI_TX0.458––
SMC_PECI_TX_R0.458––
SMC_PP1V8_WLANBT_ISENSE0.816––
SMC_PP3V3_WLANBT_ISENSE0.815––
SMC_PROCHOT_L0.453––
SMC_RSMRST_L0.446––
SMC_SYSRST_L0.448––
SMCRST_TIEOFF0.703––
SML_PCH_0_CLK0.804––
SML_PCH_0_DATA0.800––
SOC_AMBER_ROL––
SOC_BLUE_AWAKEOL––
SOC_BLUE_ROL––
SOC_CLKREQ_L0.813––
SOC_CLKREQ_R_L0.462––
SOC_COLD_RESET_L0.463––
SOC_DDR0_RREF0.540––
SOC_DDR0_ZQ0.483––
SOC_DDR1_RREF0.533––
SOC_DDR2_RREF0.530––
SOC_DDR3_RREF0.532––
SOC_DDR3_ZQ0.602––
SOC_DFU_STATUS0.469––
SOC_DOCK_CONNECT0.473––
SOC_FORCE_DFU0.469––
SOC_GREEN_DDROL––
SOC_GREEN_ROL––
SOC_HOLD_RESET0.460––
SOC_JTAG_SEL0.458––
SOC_MIPI0C_REXT0.816––
SOC_MIPI1C_REXT0.816––
SOC_MIPID_REXT0.816––
SOC_PCIE_DN_REXT0.785––
SOC_PCIE_STG0_REXT0.785––
SOC_PCIE_STG1_REXT0.785––
SOC_PCIE_UP_REXT0.786––
SOC_PERST_L0.463––
SOC_RED_ROL––
SOC_RED_SLPS2ROL––
SOC_SOCHOT_L0.460––
SOC_SWD_MUX_SEL_PCH0.584––
SOC_TESTMODE0.461––
SOC_USB_REXT0.201––
SOC_USB_VBUS0.685––
SOC_VDDCPU_SENSE0.034–31.300R
SOC_WDOG0.495––
SOC_XTAL24M_IN0.818––
SOC_XTAL24M_OUT0.806––
SOC_XTAL24M_OUT_R0.806––
SPI_ACCEL_CS_L0.470––
SPI_AOP_SENSOR_CLK0.489––
SPI_AOP_SENSOR_CLK_R0.464––
SPI_AOP_SENSOR_MISO0.473––
SPI_AOP_SENSOR_MISO_R0.492––
SPI_AOP_SENSOR_MOSI0.493––
SPI_AOP_SENSOR_MOSI_R0.466––
SPI_DFR_CLK0.51––
SPI_DFR_CLK_R0.463––
SPI_DFR_CS_L0.50––
SPI_DFR_MISO0.474––
SPI_DFR_MISO_R0.51––
SPI_DFR_MOSI0.51––
SPI_DFR_MOSI_R0.463––
SPI_IO2_STRAP_L0.594––
SPI_MESA_CLK0.483––
SPI_MESA_CLK_CONN0.540––
SPI_MESA_CLK_R0.463––
SPI_MESA_MISO0.468––
SPI_MESA_MISO_CONN0.466––
SPI_MESA_MOSI0.483––
SPI_MESA_MOSI_CONN0.487––
SPI_MESA_MOSI_R0.463––
SPI_PCHROM_IO<2>0.802––
SPI_PCHROM_IO<3>0.813––
SPI_PCHROM_MOSI0.820––
SPI_SOCROM_CLK0.479––
SPI_SOCROM_CS_L0.4651.800–
SPI_SOCROM_MISO0.4331.800–
SPI_SOCROM_MISO_R0.4301.800–
SPI_SOCROM_MOSI0.421––
SPI_SOCROM_MOSI_R0.429––
SPI_SOCROM_WP_L0.6141.800–
SPI_TPAD_3V3_CLK0.471––
SPI_TPAD_3V3_CLK_R0.451––
SPI_TPAD_3V3_CS_L0.458––
SPI_TPAD_3V3_MISO0.448––
SPI_TPAD_3V3_MOSI0.479––
SPI_TPAD_3V3_MOSI_R0.462––
SPI_TPAD_CLK0.428––
SPI_TPAD_CLK_R0.428––
SPI_TPAD_CS_L0.434––
SPI_TPAD_MISO0.429––
SPI_TPAD_MISO_R0.426––
SPI_TPAD_MOSI0.440––
SPI_TPAD_MOSI_R0.442––
SPIROM_USE_MLB0.822––
SPKR_ID00.467––
SPKR_ID10.462––
SPKRAMP_INT_L0.372––
SPKRAMP_LT_AREG0.585––
SPKRAMP_LT_BSTN0.778––
SPKRAMP_LT_BSTP0.777––
SPKRAMP_LT_DREG0.537––
SPKRAMP_LT_MODE0.003–1.000R
SPKRAMP_LT_OUTN0.498––
SPKRAMP_LT_OUTP0.498––
SPKRAMP_LW_AREG0.584––
SPKRAMP_LW_BSTN0.778––
SPKRAMP_LW_BSTP0.777––
SPKRAMP_LW_DREG0.538––
SPKRAMP_LW_MODE0.414––
SPKRAMP_LW_OUTN0.498––
SPKRAMP_LW_OUTP0.497––
SPKRAMP_RESET_L0.375––
SPKRAMP_RT_AREG0.585––
SPKRAMP_RT_BSTN0.777––
SPKRAMP_RT_BSTP0.777––
SPKRAMP_RT_DREG0.541––
SPKRAMP_RT_MODE0.463––
SPKRAMP_RT_OUTN0.491––
SPKRAMP_RT_OUTP0.492––
SPKRAMP_RT_SNSN0.491––
SPKRAMP_RT_SNSP0.492––
SPKRAMP_RW_AREG0.583––
SPKRAMP_RW_BSTN0.777––
SPKRAMP_RW_BSTP0.776––
SPKRAMP_RW_DREG0.541––
SPKRAMP_RW_MODE0.467––
SPKRAMP_RW_OUTN0.492––
SPKRAMP_RW_OUTP0.494––
SPKRCONN_LT_OUTN0.498––
SPKRCONN_LT_OUTP0.498––
SPKRCONN_LW_OUTN0.498––
SPKRCONN_LW_OUTP0.497––
SPKRCONN_RT_OUTN0.491––
SPKRCONN_RT_OUTP0.492––
SPKRCONN_RW_OUTN0.492––
SPKRCONN_RW_OUTP0.494––
SPMI_CLK0.484––
SPMI_CLK_R0.465––
SPMI_DATA0.436––
SPMI_DATA_R0.433––
SPROM_CS0.495––
SPROM_CS_R0.579––
SSD_BFH0.425––
SSD_PMU_RESET_L0.463––
SSD0_CLK24M0.442––
SSD0_CLK24M_010.449––
SSD0_CLK24M_230.447––
SSD0_CLK24M_R0.443––
SSD0_CLKREQ0_L0.440––
SSD0_CLKREQ1_L0.447––
SSD0_CLKREQ2_L0.439––
SSD0_CLKREQ3_L0.452––
SSD0_OCARINA_FORCE_EN0.580––
SSD0_OCARINA_IREF0.756––
SSD0_OCARINA_LPB_L0.437––
SSD0_OCARINA_PFN0.438––
SSD0_OCARINA_PGOOD0.766––
SSD0_OCARINA_POK20.000––
SSD0_OCARINA_RESET_L0.437––
SSD0_OCARINA_TCAL0.777––
SSD0_OCARINA_TDEV10.777––
SSD0_OCARINA_TDEV20.773––
SSD0_OCARINA_VDD_LDO0.373––
SSD0_OCARINA_VREF0.768––
SSD0_OCARINA_WP_L0.533––
SSD0_PCIE_RESET_L0.423––
SSD0_S4E_BOOT20.441––
SSD0_S4E_JTAG_SEL0.437––
SSD0_S4E_JTAG_TRST_L0.437––
SSD0_S4E_UART_TX0.485––
SSD0_S4E0_AVDD18_PLL0.369––
SSD0_S4E0_DROOP_L0.494––
SSD0_S4E0_JTAG_TDI0.487––
SSD0_S4E0_JTAG_TDO0.467––
SSD0_S4E0_PCI_AVDD_H0.369––
SSD0_S4E0_PCIE_RESREF0.789––
SSD0_S4E0_SWD_UID00.496––
SSD0_S4E0_SWD_UID10.484––
SSD0_S4E0_UART_TX0.485––
SSD0_S4E0_VPP0.570––
SSD0_S4E0_ZQ_C0.102––
SSD0_S4E0_ZQ_L0.304––
SSD0_S4E1_AVDD18_PLL0.366––
SSD0_S4E1_DROOP_L0.506––
SSD0_S4E1_JTAG_TDO0.459––
SSD0_S4E1_PCI_AVDD_H0.366––
SSD0_S4E1_PCIE_RESREF0.785––
SSD0_S4E1_SWD_UID00.494––
SSD0_S4E1_SWD_UID10.495––
SSD0_S4E1_UART_TX0.495––
SSD0_S4E1_VPP0.566––
SSD0_S4E1_ZQ_C0.102––
SSD0_S4E1_ZQ_L0.303––
SSD0_S4E2_AVDD18_PLL0.369––
SSD0_S4E2_DROOP_L0.480––
SSD0_S4E2_JTAG_TDO0.464––
SSD0_S4E2_PCI_AVDD_H0.369––
SSD0_S4E2_PCIE_RESREF0.789––
SSD0_S4E2_SWD_UID00.474––
SSD0_S4E2_SWD_UID10.475––
SSD0_S4E2_UART_TX0.475––
SSD0_S4E2_VPP0.570––
SSD0_S4E2_ZQ_C0.102––
SSD0_S4E2_ZQ_L0.303––
SSD0_S4E3_AVDD18_PLL0.367––
SSD0_S4E3_DROOP_L0.523––
SSD0_S4E3_JTAG_TDO0.519––
SSD0_S4E3_PCI_AVDD_H0.367––
SSD0_S4E3_PCIE_RESREF0.789––
SSD0_S4E3_SWD_UID00.516––
SSD0_S4E3_SWD_UID10.515––
SSD0_S4E3_UART_TX0.513––
SSD0_S4E3_VPP0.568––
SSD0_S4E3_ZQ_C0.102––
SSD0_S4E3_ZQ_L0.304––
SSD0_STG01_ADDR0.584––
SSD0_SWCLK0.427––
SSD0_SWDIO0.423––
SSD0_TPS62180_FB1.427––
SSD0_TPS62180_FB_R0.409––
SSD0_TPS62180_SS0.550––
SSD0_VR_P2V7_EN0.653––
SSD0_VR_P2V7_EN_R0.654––
SSD0_VR_P2V7_PGOOD0.574––
SSTATE_BLUEOL––
SSTATE_BLUE_ROL––
SSTATE_GREENOL––
SSTATE_GREEN_ROL––
SSTATE_REDOL––
SSTATE_RED_ROL––
SWD_DEBUG_SWCLK0.498––
SWD_DEBUG_SWDIO0.497––
SWD_SOC_SWCLK0.467––
SWD_SOC_SWDIO0.462––
SYS_DETECTOL––
SYS_DETECT_L0.589––
TBT_POC_RESET0.575––
TBT_PWR_EN0.750––
TBT_T_BATLOW_L0.615––
TBT_T_CIO_PWR_EN0.501––
TBT_T_CLKREQ_L0.808––
TBT_T_DPMUX_SEL0.552––
TBT_T_DPMUX_SEL_R0.669––
TBT_T_PCI_RESET_L0.498––
TBT_T_PCIE_BIAS0.790––
TBT_T_PLUG_EVENT_L0.547––
TBT_T_PWR_EN0.569––
TBT_T_RBIAS0.783––
TBT_T_ROM_HOLD_L0.711––
TBT_T_ROM_WP_L0.607––
TBT_T_RSENSE0.030–0.400R
TBT_T_SPI_CLK0.582––
TBT_T_SPI_CLK_DBG0.608––
TBT_T_SPI_CS_L0.614––
TBT_T_SPI_MISO0.617––
TBT_T_SPI_MOSI0.619––
TBT_T_TMU_CLK_IN0.617––
TBT_T_TMU_CLK_OUT0.618––
TBT_T_USB_PWR_EN0.496––
TBT_TA_LSRX0.752––
TBT_TA_LSTXOL––
TBT_TA_USB2_MXCTL0.615––
TBT_TA_USB2_RBIAS0.203––
TBT_TB_LSRX0.786––
TBT_TB_LSTX0.814––
TBT_TB_USB2_RBIAS0.202––
TBT_WAKE_3V3_L0.527––
TBT_WAKE_L0.466––
TBT_X_CIO_PWR_EN0.569––
TBT_X_CLKREQ_L0.808––
TBT_X_DPMUX_SEL0.552––
TBT_X_DPMUX_SEL_R0.619––
TBT_X_PCI_RESET_L0.583––
TBT_X_PCIE_BIAS0.795––
TBT_X_PLUG_EVENT_L0.618––
TBT_X_PWR_EN0.570––
TBT_X_RBIAS0.784––
TBT_X_ROM_HOLD_L0.712––
TBT_X_ROM_WP_L0.609––
TBT_X_SPI_CLK0.579––
TBT_X_SPI_CLK_DBG0.680––
TBT_X_SPI_CS_L0.614––
TBT_X_SPI_MISO0.618––
TBT_X_SPI_MOSI0.621––
TBT_X_USB_PWR_EN0.567––
TBT_XA_LSRX0.778––
TBT_XA_LSTX0.815––
TBT_XA_USB2_MXCTL0.623––
TBT_XA_USB2_RBIAS0.203––
TBT_XB_LSRX0.72––
TBT_XB_LSTX0.78––
TBT_XB_USB2_RBIAS0.204––
TBTTHMSNS_D1_N0.000––
TBTTHMSNS_D1_P0.658––
TEST_CPU_A350.306––
TEST_CPU_BJ340.328––
TEST_CPU_BJ360.328––
TEST_CPU_CN360.354––
TEST_CPU_D340.306––
TEST_CPU_F340.361––
TEST_CPU_F370.362––
TEST_ISNS_EADCNOL––
TEST_ISNS_EADCPOL––
TEST_NOA_N_100.824––
TEST_NOA_N_110.825––
TEST_SOC_AMUXOUT0.818––
TEST_SOC_TST_CLKOUT0.463––
TP_CPU_PWRGD0.342––
TP_DFR_TOUCH_GPIO2OL––
TP_DFR_TOUCH_PANEL_DETECTOL––
TP_DFR_TOUCH_ROM_WCOL––
TP_JTAG_SOC_TRST_L0.462––
TP_LCD_IRQ_LOL––
TP_Q3100_DRAIN0.633––
TP_Q3200_DRAIN0.641––
TP_QB300_DRAIN0.324––
TP_QB400_DRAIN0.625––
TP_SMC_FIXTURE_MODE_L0.4671.800–
TP_SOC_DEBUGPRT_RX0.462––
TP_SOC_DEBUGPRT_TX0.461––
TP_SPI_PCHROM_CLK0.824––
TP_SPI_PCHROM_CS_L0.808––
TP_SSD0_OCARINA_NAND_VCC_DET0.760––
TP_SSD0_S4E0_ANI0_VREF0.608––
TP_SSD0_S4E0_ANI1_VREF0.607––
TP_SSD0_S4E1_ANI0_VREF0.607––
TP_SSD0_S4E1_ANI1_VREF0.608––
TP_SSD0_S4E2_ANI0_VREF0.605––
TP_SSD0_S4E2_ANI1_VREF0.605––
TP_SSD0_S4E3_ANI0_VREF0.607––
TP_SSD0_S4E3_ANI1_VREF0.609––
TP_UPC_TB_GPIO00.772––
TP_UPC_TB_GPIO10.771––
TP_UPC_TB_SWD_CLK0.752––
TP_UPC_TB_SWD_DATA0.746––
TP_USB_FIXT1_N0.482––
TP_USB_FIXT1_P0.484––
TP_USB_FIXT2_N0.486––
TP_USB_FIXT2_P0.484––
TP_USB3_EXTC_D2R_N0.344––
TP_USB3_EXTC_D2R_P0.342––
TP_USB3_EXTC_R2D_C_N0.328––
TP_USB3_EXTC_R2D_C_P0.330––
TP_USBC_PP20V_TAOL––
TP_USBC_PP20V_TBOL––
TP_USBC_PP20V_XAOL––
TP_USBC_PP20V_XBOL––
TPAD_3V3_ACTUATOR_DISABLE_L0.981––
TPAD_3V3_SPI_EN0.636––
TPAD_3V3_SPI_INT_L0.992––
TPAD_ACTUATOR_DISABLE_L0.464––
TPAD_KBD_WAKE_L0.468––
TPAD_SPI_EN0.466––
TPAD_SPI_INT_L0.463––
UART_BT_D2R0.463––
UART_BT_D2R_CTS_L0.462––
UART_SE_D2R0.463––
UART_SE_D2R_CTS_L0.462––
UART_SE_R2D0.464––
UART_SE_R2D_RTS_L0.464––
UART_WLAN_D2R0.467––
UART_WLAN_D2R_CTS_L0.467––
UPC_I2C_INT_L0.482––
UPC_PMU_RESET0.524––
UPC_T_5V_EN0.530––
UPC_T_5V_EN_R0.528––
UPC_T_SPI_CLK0.583––
UPC_T_SPI_CS_L0.605––
UPC_T_SPI_MISO0.607––
UPC_T_SPI_MOSI0.610––
UPC_TA_DBG30.746––
UPC_TA_DBG4OL––
UPC_TA_GATE10.630––
UPC_TA_GATE20.622––
UPC_TA_GPIO00.744––
UPC_TA_GPIO10.742––
UPC_TA_R_OSC0.524––
UPC_TA_SPI_CLK0.560––
UPC_TA_SPI_CS_L0.582––
UPC_TA_SPI_MISO0.578––
UPC_TA_SPI_MOSI0.587––
UPC_TA_SS0.500––
UPC_TA_UART_RX0.722––
UPC_TA_UART_TX0.700––
UPC_TB_DBG10.74––
UPC_TB_DBG20.74––
UPC_TB_DBG30.74––
UPC_TB_DBG40.74––
UPC_TB_R_OSC0.49––
UPC_TB_SS0.49––
UPC_X_5V_EN0.556––
UPC_X_5V_EN_R0.538––
UPC_X_SPI_CLK0.585––
UPC_X_SPI_CS_L0.610––
UPC_X_SPI_MISO0.608––
UPC_X_SPI_MOSI0.612––
UPC_XA_DBG10.576––
UPC_XA_DBG20.577––
UPC_XA_GATE10.663––
UPC_XA_GATE20.622––
UPC_XA_GPIO00.747––
UPC_XA_R_OSC0.536––
UPC_XA_SS0.528––
UPC_XA_UART_RX0.760––
UPC_XA_UART_TX0.70––
UPC_XB_DBG30.530––
UPC_XB_DBG40.529––
UPC_XB_GPIO00.776––
UPC_XB_GPIO10.73––
UPC_XB_R_OSC0.49––
UPC_XB_SPI_CLK0.595––
UPC_XB_SPI_CS_L0.631––
UPC_XB_SPI_MISO0.631––
UPC_XB_SPI_MOSI0.636––
UPC_XB_SS0.49––
USB_DBG_XA_F_N0.488––
USB_DBG_XA_F_P0.492––
USB_SOC_N0.727––
USB_SOC_P0.750––
USB_SOC_TYPEC_N0.722––
USB_SOC_TYPEC_P0.721––
USB_UPC_TA_F_N0.413––
USB_UPC_TA_F_P0.414––
USB_UPC_TB_F_N0.41––
USB_UPC_TB_F_P0.41––
USB_UPC_XA_N0.756––
USB_UPC_XA_P0.756––
USB_UPC_XB_F_N0.41––
USB_UPC_XB_F_P0.41––
USB2_UPC_XA_N0.485––
USB2_UPC_XA_P0.489––
USB3_EXTA_D2R_N0.346––
USB3_EXTA_D2R_P0.343––
USB3_EXTA_R2D_C_N0.334––
USB3_EXTA_R2D_C_P0.355––
USB3_EXTA_R2D_N0.739––
USB3_EXTA_R2D_P0.741––
USBC_T_RESET_L0.725––
USBC_TA_AUXLSX10.681––
USBC_TA_AUXLSX20.685––
USBC_TA_CC10.582––
USBC_TA_CC1_CONN0.74––
USBC_TA_CC20.580––
USBC_TA_CC2_CONN0.76––
USBC_TA_SBU1OL––
USBC_TA_SBU2OL––
USBC_TA_USB_BOT_NOL––
USBC_TA_USB_BOT_POL––
USBC_TA_USB_TOP_NOL––
USBC_TA_USB_TOP_POL––
USBC_TB_AUXLSX10.704––
USBC_TB_AUXLSX20.707––
USBC_TB_CC10.58––
USBC_TB_CC1_CONN0.76––
USBC_TB_CC20.58––
USBC_TB_CC2_CONN0.77––
USBC_TB_SBU10.890––
USBC_TB_SBU20.885––
USBC_TB_USB_BOT_NOL––
USBC_TB_USB_BOT_POL––
USBC_TB_USB_TOP_N0.960––
USBC_TB_USB_TOP_P0.903––
USBC_XA_AUXLSX10.708––
USBC_XA_AUXLSX20.710––
USBC_XA_CC10.597––
USBC_XA_CC1_CONN0.939––
USBC_XA_CC20.599––
USBC_XA_CC2_CONN0.927––
USBC_XA_SBU10.824––
USBC_XA_SBU20.866––
USBC_XA_USB_DBG_BOT_N0.315––
USBC_XA_USB_DBG_BOT_P0.315––
USBC_XA_USB_DBG_TOP_N0.316––
USBC_XA_USB_DBG_TOP_P0.317––
USBC_XA_USB_TOP_N0.003–0.344R
USBC_XA_USB_TOP_P0.579––
USBC_XB_AUXLSX10.708––
USBC_XB_AUXLSX20.710––
USBC_XB_CC10.57––
USBC_XB_CC1_CONN0.947––
USBC_XB_CC20.58––
USBC_XB_CC2_CONN0.950––
USBC_XB_SBU10.842––
USBC_XB_SBU2OL––
USBC_XB_USB_BOT_N0.954––
USBC_XB_USB_BOT_P0.953––
USBC_XB_USB_TOP_N0.951––
USBC_XB_USB_TOP_POL––
UVP_DIS_L0.570––
VR0V9_IND_TBT_T0.3220.900–
VR0V9_IND_TBT_X0.3530.900–
WIFI_SROM_ORGOL––
WLAN_AUDIO_SYNC0.694––
WLAN_CONTEXT_A0.461––
WLAN_CONTEXT_B0.462––
WLAN_JTAG_SEL0.739––
WLAN_JTAG_TCK0.471––
WLAN_JTAG_TDI0.466––
WLAN_JTAG_TDO0.754––
WLAN_JTAG_TMS0.468––
WLAN_JTAG_TRST_L0.754––
WLAN_OP_ENOL––
WLAN_OP_EN_LOL––
WLAN_PWR_EN0.484––
WLAN_SROM_STRAP0.739––
XDP_BPM_L<0>0.308––
XDP_CPU_PWRBTN_L0.783––
XDP_CPU_TCK0.058–54.800R
XDP_CPU_TDI0.251––
XDP_CPU_TDO0.239––
XDP_CPU_TMS0.252––
XDP_CPU_TRST_L0.297––
XDP_DBRESET_L0.819––
XDP_DP_INT_HPD0.591––
XDP_PCH_OBSDATA_A00.824––
XDP_PCH_OBSDATA_A10.824––
XDP_PCH_OBSDATA_A20.823––
XDP_PCH_OBSDATA_A30.824––
XDP_PCH_OBSDATA_B00.826––
XDP_PCH_OBSDATA_D10.823––
XDP_PCH_OBSDATA_D20.824––
XDP_PCH_OBSDATA_D30.824––
XDP_PCH_OBSFN_C10.824––
XDP_PCH_TCK0.317––
XDP_PCH_TDI0.256––
XDP_PCH_TDO0.241––
XDP_PCH_TMS0.254––
XDP_PCH_TRST_L0.299––
XDP_PM_RSMRST_L1.499––
XDP_PRESENT_CPU1.311––
XDP_PRESENT_L0.459––
XDP_USB_EXTA_OC_L0.760––
XDP_USB_EXTB_OC_L0.763––
XDP_USB_EXTD_OC_L0.763––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00850?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00850: diode 0.460, voltage 12.220. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00850?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00850: diode 0.430, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-00850?

OpenBoardData's known-good values for PP3V3_S5 on the 820-00850: diode 0.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00850 board?

Open your own 820-00850 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License