Apple laptop board · OpenBoardData

820-3462 known-good readings

Known-good readings for the Apple laptop board 820-3462: 361 nets, including 30 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 30 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3462.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 30 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 7

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.313.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is an always-on 3.42 V rail, judged from its name (G3H = always on); it should be present whenever the board has power. Community readings for this board give diode 0.31 to ground and 3.400 V with power applied, as a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A voltage far below 3.400 V or a diode reading well off 0.31 points to a fault on the rail or its load, but no known-good resistance reading exists here, so compare against a matching net or a known-good board before condemning anything.

PPBUS_G3H0.14012.800–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main bus rail that the G3H suffix marks as always-on, from the name. Known-good readings here are diode 0.140 and voltage 12.800, though the archive gives no condition for them, so treat them as a guide.

  • Check with the board unpowered: diode mode from PPBUS_G3H to ground, expecting around 0.140.
  • Then apply power and measure the voltage, expecting around 12.800.
  • A diode reading far below known-good usually points to a short or a leaky part on the rail; a voltage far off points to the supply or charging side not coming up. No known-good resistance reading exists for this rail.
PPBUS_G3H_R0.16––
AI: what PPBUS_G3H_R is and how to check it
  • What it is: PPBUS_G3H_R is the main bus rail; the "G3H" in the name indicates it is always-on, present whenever power is connected.
  • Known-good reading: diode 0.16 to ground, from the readings archive. No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from PPBUS_G3H_R to ground and compare with 0.16. Then apply power and measure the rail voltage; no known-good voltage is listed, so compare against a known-good board of the same model.
  • If far from 0.16: a much lower diode reading usually suggests a short or a leaky component on the rail; a much higher one suggests an open path. This is a guide only, not a confirmed diagnosis.
PPDCIN_G3H_ISOLOL––
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL — the name says this is the isolated DC input rail, part of the G3H always-on startup stage: the DC-in voltage after the isolation side of the input path, present whenever power is connected.

  • Known-good reading: diode mode to ground is OL (open) in the readings archive. That's the only known-good value recorded here; there's no known-good voltage or resistance for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and expect OL. Then apply power and measure the DC voltage on the rail.
  • If it reads far from OL to ground: a low or shorted diode reading points to a fault on that side of the isolation, not to the input itself. A voltage that's absent or well below the input with power applied suggests the input path isn't passing power through.

These archive readings are community contributions and vary with board state, so treat them as a guide rather than a spec.

PPVBAT_G3H_CHGR_REG0.140––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG — the name indicates a battery/charger-related rail that is always on (G3H), derived from the charger side (CHGR).

  • Known-good reading in the archive: diode mode to ground 0.140 (board unpowered). No known-good voltage reading here.
  • Check it with power off in diode mode from the net to ground, then with power applied measure the voltage on the net.
  • A diode reading far from 0.140 usually points to a short or a leaky part on that rail, but one reading isn't proof; compare with a matching net or a known-good board before replacing anything.
PPVIN_G3H_P3V42G3H0.38––
AI: what PPVIN_G3H_P3V42G3H is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V42G3H is the always-on G3H input feed that becomes the P3V42G3H rail — an early, always-present supply on this board.
  • Known-good reading: diode 0.38 (archive value, a guide; board state affects it). No known-good voltage or resistance reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the net — expect around 0.38. Then power up and measure the DC voltage on the net.
  • If it's far off: a much lower diode reading usually suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing connection. Confirm with the powered voltage before replacing anything.
PPVRTC_G3H–3.300–
AI: what PPVRTC_G3H is and how to check it

PPVRTC_G3H is the always-on RTC rail; the G3H suffix comes from its name and marks it as a rail that should be present whenever power is connected. The only known-good reading here is 3.300 V, with no condition recorded, and there is no known-good diode or resistance value for this rail. Check it unpowered in diode mode from PPVRTC_G3H to ground, then power the board and measure the voltage. A voltage well below 3.300 V points to a load or short on the rail or a missing source; with no known-good diode value, compare against a matching rail or a known-good board rather than judging on one reading.

S5 and SUS: standby 5

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.183.300–
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is a 3.3 V standby rail; the "S5" in the name marks it as a standby-stage supply (from the name, not from a board file).
  • Known-good readings: diode 0.18 and 3.300 V, from the readings archive; treat these as a guide since they vary with board state.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S5 to ground and compare with 0.18; then apply power and measure the voltage, expecting about 3.300 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail, while a missing or low voltage points to the standby supply not coming up. No known-good resistance reading is available here, so compare against a matching net or a known-good board before condemning anything.
PP3V3_SUS0.43––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V suspend (standby) rail; the S5/SUS naming indicates it's a standby rail, from the name.

  • Known-good: diode 0.43 to ground (no condition recorded). No known-good voltage reading here.
  • Check: power off, diode mode from PP3V3_SUS to ground; then power on and measure the voltage.
  • A diode reading far from 0.43 suggests a short or leak on that rail; confirm with a second measurement before replacing anything.
PP5V_S50.455.000–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the standby 5 V rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the board fully powers on. The readings archive gives a known-good diode value of 0.45 and a voltage of 5.000 for this net. To check it, power the board off and measure diode mode from PP5V_S5 to ground, then apply power and measure the voltage on the rail. A diode reading far from 0.45 usually points to a short or a leaky component on the rail, while a voltage well below 5.000 suggests the standby supply isn't coming up. No known-good resistance reading is listed here, so compare against a matching net or a known-good board if you need one.

PP5V_SUS–5.000–
AI: what PP5V_SUS is and how to check it
  • PP5V_SUS is the 5 V standby rail, from its name: S5/SUS means standby, present before the board fully powers on.
  • Known-good reading here: 5.000 V. No known-good diode or resistance reading is recorded for this rail.
  • To check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage.
  • A voltage far from 5.000 V points to the standby supply or its load, but one reading doesn't confirm a bad part. No parts or nets are listed for this rail, so trace it on the board itself.
PPVIN_S5_HS_OTHER_ISNS0.15––
AI: what PPVIN_S5_HS_OTHER_ISNS is and how to check it
  • What it is: From the name, PPVIN_S5_HS_OTHER_ISNS is a high-side input rail in the S5/SUS standby stage. "ISNS" suggests a current-sense-related node, but the exact circuit isn't documented here.
  • Known-good reading: diode 0.15 (from the readings archive, condition not stated). No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.15. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on that rail; a much higher one to an open path. Confirm with a second measurement before replacing anything.

S4 3

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.4215––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 startup stage; both the voltage and stage come from the rail's name, not from a schematic. The only known-good reading here is a diode value of 0.4215 to ground, with no condition recorded. Check it unpowered in diode mode from PP3V3_S4 to ground, then power the board and measure the voltage. A diode reading far below 0.4215 usually points to a short or a leaky load on the rail, while a far higher or open reading points to a broken connection; no known-good voltage reading exists here, so compare against a matching rail or a known-good board.

PP5V_S40.40––
AI: what PP5V_S4 is and how to check it
  • PP5V_S4 is a 5 V rail in the S4 startup stage, both from the name. It's an always-on-to-S4 power rail on this Apple 820-3462 logic board.
  • Known-good reading: diode 0.40 to ground (community archive, condition not stated). No known-good voltage reading here.
  • Check it unpowered in diode mode from PP5V_S4 to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.40 suggests a short or leaky part on the rail; no voltage when expected points to the rail not being enabled or its source failing. Confirm with a second measurement before replacing anything.
PP5V_S4_CUMULUS0.4517––
AI: what PP5V_S4_CUMULUS is and how to check it

PP5V_S4_CUMULUS is a 5 V rail that, from its name, belongs to the S4 startup stage and the CUMULUS section of this 820-3462 board. The only known-good reading here is a diode value of 0.4517 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board at S4. A diode reading far below 0.4517 usually points to a short or a leaky part on the rail, while a much higher or open reading suggests a broken connection; treat these as a guide and confirm before replacing anything.

S3: memory 6

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V5R1V35_S30.13––
AI: what PP1V5R1V35_S3 is and how to check it
  • What it is: PP1V5R1V35_S3 is a 1.5 V / 1.35 V rail; the S3 suffix marks it as a memory-stage rail, both from the name. Which parts sit on it isn't known here.
  • Known-good reading: diode 0.13 to ground, from the readings archive (community value, a guide only; no condition recorded). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.13; then power on and measure the rail voltage against its 1.5 V / 1.35 V name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Neither confirms a bad part on one reading, so trace the rail before replacing anything.
PP3V3_S30.33––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V supply for the S3 (memory) stage, judged from its name. The archive lists a known-good diode reading of 0.33 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S3 to ground and compare with 0.33, then power up and check the voltage. A diode value far below 0.33 suggests a short or leaky load on the rail; a far higher one can mean an open path. These are community readings and only a guide, so confirm against a matching net or a known-good board before replacing anything.

PP5V_S30.50––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is the 5 V rail that comes up at the S3 (memory) stage of startup, inferred from its name. The only known-good reading here is a diode value of 0.50; no voltage or resistance values are recorded for it.

  • With the board unpowered, measure diode mode from PP5V_S3 to ground and compare with 0.50.
  • Then power the board and check the rail sits near 5 V when the S3 stage is reached.
  • A diode reading far below 0.50 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken path. A missing voltage with a normal diode reading points upstream, at the rail's enable or source.
  • These are community readings and vary with board state, so treat 0.50 as a guide, not a guarantee.
PP5V_S3_ALSCAMERA_F0.50––
AI: what PP5V_S3_ALSCAMERA_F is and how to check it
  • What it is: PP5V_S3_ALSCAMERA_F is a 5 V rail that, from its name, belongs to the S3 (memory) startup stage and feeds the camera circuit. The parts on it aren't documented here.
  • Known-good reading: diode 0.50 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: with power off, measure diode mode from the rail to ground and compare with 0.50; then power up and measure the DC voltage, expecting about 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with voltage before replacing anything.
PP5V_S3_LTUSB_A_F0.46––
AI: what PP5V_S3_LTUSB_A_F is and how to check it
  • What it is: PP5V_S3_LTUSB_A_F is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state and feeds the LTUSB_A section. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.46 in diode mode to ground, board unpowered. No known-good voltage reading here, so compare against a matching rail or a known-good board.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage, expecting about 5 V.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage points to the rail's enable or supply upstream. These are likely causes, not confirmed.
PPVTTDDR_S30.34––
AI: what PPVTTDDR_S3 is and how to check it

PPVTTDDR_S3 is a memory-stage (S3) rail; the "VTTDDR" part of the name indicates it is the DDR termination rail, which is general naming convention rather than something confirmed by board data. The only known-good reading here is a diode value of 0.34 to ground, with no condition recorded. Check it by powering the board off and measuring diode mode from the rail to ground, then powering up and measuring the voltage on the rail. There is no known-good voltage reading here, so compare against a matching rail on a known-good board. A diode reading far from 0.34 usually points to a short or a leaky component on that rail, but a single reading is only a guide.

S0: running 9

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V75_S0_DDRVTT0.14––
AI: what PP0V75_S0_DDRVTT is and how to check it

PP0V75_S0_DDRVTT is a 0.75 V rail; the name suggests it is the DDR termination voltage (DDRVTT) and that it runs in the S0 (running) state. The archive lists one known-good reading: diode 0.14, with no condition noted, and no known-good voltage reading here.

  • Check it unpowered in diode mode from the rail to ground; compare with the 0.14 guide.
  • Then power the board and measure the voltage, expecting about 0.75 V from the name (general expectation, not a recorded value).
  • A diode reading far from 0.14 usually points to a short or a leaky part on the rail; a correct diode reading with wrong voltage points more to the rail's supply or enable circuit.

These are community readings and vary with board state, so treat them as a guide rather than a confirmed fault.

PP1V05_S00.01––
AI: what PP1V05_S0 is and how to check it
  • PP1V05_S0 is a 1.05 V rail that is up in the S0 (running) state, from its name. The archive has only one known-good reading for it: diode 0.01, with no condition noted.
  • To check it, power off and measure diode mode from the rail to ground; then power on and measure the voltage. No known-good voltage reading here.
  • A diode reading far from 0.01 usually points to a short or a leaky load on the rail, but confirm with a second measurement before replacing anything.
PP1V5_S00.36––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" suffix, from its name, marks it as a running-state supply. The only known-good reading here is a diode value of 0.36 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. No known-good voltage reading is listed for this rail. A diode reading far from 0.36 usually points to a short or a damaged load on the rail, but confirm with the voltage measurement before suspecting a part.

PP3V3_S00.35––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, as the name indicates. The archive lists a diode reading of 0.35 for it; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S0 to ground and compare with 0.35, then apply power and check the voltage. A diode reading far below 0.35 suggests a short or a failing load on the rail; a far higher or open reading suggests a broken path. The 0.35 is a community guide and varies with board state, so confirm against a known-good board before replacing anything.

PP3V3_S0_SSD_FLT0.35––
AI: what PP3V3_S0_SSD_FLT is and how to check it

PP3V3_S0_SSD_FLT is a 3.3 V rail, from its name: the S0 part means it belongs to the running state, and SSD_FLT suggests it feeds the SSD circuitry. The only known-good reading in the archive is a diode value of 0.35 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.35 usually points to a short or a leaky part on that rail, but one reading alone isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP5V_S00.41––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail active in S0, the running state, as its name indicates. The archive lists a diode reading of 0.41 to ground for this net; no voltage or resistance known-good value is recorded here. Check it unpowered in diode mode from PP5V_S0 to ground, then power the board and measure the voltage in the S0 state. A diode reading far below 0.41 usually points to a short or a leaky load on the rail, while a missing or low voltage with a normal diode reading points upstream to the regulator or its enable. These readings are community guides and vary with board state, so confirm against a matching net or a known-good board before replacing anything.

PP5V_S0_HDD_FLT0.40––
AI: what PP5V_S0_HDD_FLT is and how to check it

PP5V_S0_HDD_FLT — 820-3462

  • What it is: from the name, a 5 V rail (PP5V) that is present in the S0 running state and feeds the HDD circuit; the FLT suffix suggests a filtered or fault-related branch. Which parts sit on it isn't documented here.
  • Known-good reading: diode 0.40 in diode mode to ground, with the board unpowered. That is the only known-good value recorded; there is no known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the net to ground and compare with 0.40. Then power up and measure the DC voltage — it should be near 5 V in S0, though that figure is general, not from this board's data.
  • If it's far off: a much lower diode reading points to a short or a leaky part on the rail; a much higher or open reading points to a missing feed or a broken trace. A single reading doesn't condemn a part, so confirm with the voltage measurement before replacing anything.
PPBUS_S0_LCDBKLT_PWR_SW0.877––
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
  • What it is: From the name, PPBUS_S0_LCDBKLT_PWR_SW is the switched backlight power rail on the PPBUS supply, active in the S0 (running) state. The _SW suffix suggests it is switched rather than always on.
  • Known-good reading: Diode mode to ground reads 0.877 in the archive. No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.877. Then power the board and measure the voltage on the rail.
  • If it's far off: A much lower diode reading usually points to a short or a leaky component on the rail; a much higher one can mean an open path. Treat one reading as a guide only, not proof a part is bad.
PPVOUT_S0_LCDBKLT1.09––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT — 820-3462 reference note

  • What it is: from the name, the LCD backlight output rail, enabled in the S0 (running) state. It's the boosted supply feeding the display backlight, so it should only be present once the board is powered on and the backlight circuit is enabled.
  • Known-good reading: diode mode to ground 1.09, from the readings archive. This is a community value and a guide only; no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 1.09. Then power the board and measure the voltage on the rail with the display connected and the backlight on.
  • If it's far off: a much lower diode reading suggests a short or leaky path on the rail; a much higher one suggests an open. No voltage reading is confirmed here, so compare against a known-good board of the same model before condemning a part.

Every net with a reading

NetDiodeVoltageResistance
ADAPTER_SENSE0.62––
ALL_SYS_PWRGD0.47––
AP_CLKREQ_Q_L0.46––
AP_RESET_CONN_L0.46––
AUD_CONN_HP_LEFT0.82––
AUD_CONN_HP_RIGHT0.75––
AUD_CONN_MIC0.48––
AUD_CONN_MIC_XW0.36––
AUD_CONN_SLEEVE0.48––
AUD_CONN_SLEEVE_XW0.37––
AUD_CONN_TYPEDET0.00––
AUD_SPDIF_OUT_JACK0.72––
AUD_TIPDET_INV0.00––
CHGR_ACIN0.54––
CHGR_AGATE0.65––
CHGR_AMON0.72––
CHGR_BGATE0.67––
CHGR_BMON0.73––
CHGR_BOOT0.58––
CHGR_CELL0.71––
CHGR_CSI_N0.62––
CHGR_CSI_P0.61––
CHGR_CSO_N0.15––
CHGR_CSO_P0.15––
CHGR_DCIN0.60––
CHGR_ICOMP0.73––
CHGR_LGATE0.46––
CHGR_PHASE0.15––
CHGR_RST_L0.50––
CHGR_SGATE0.65––
CHGR_UGATE0.61––
CHGR_VCOMP0.73––
CHGR_VFRQ0.53––
CHGR_VNEG0.54––
CON_DMIC_CLK0.70––
CON_DMIC_PWR0.35––
CON_DMIC_SDA10.70––
CPU_PECI_R0.28––
CPU_PROCHOT_L0.06––
CPUIMVP_PHASE1––2.00R
CPUIMVP_PHASE1G––2.00R
CPUIMVP_PHASE2––1.70R
CPUIMVP_PHASE2G––2.00R
CPUVCCIOS0_LL––8.70R
DCIN_S5_VSENSEOL––
DCIN_VSENSE_EN0.74––
DCINVSENS_EN_L0.46––
DDRREG_1V8_VREF0.62––
DDRREG_DRVH0.63––
DDRREG_DRVL0.47––
DDRREG_EN0.56––
DDRREG_FB0.67––
DDRREG_LL0.13––
DDRREG_MODE0.54––
DDRREG_TRIP0.74––
DDRREG_VBST0.62––
DDRREG_VDDQSNS0.13––
DDRREG_VTTSNS0.14––
DP_INT_AUX_C_N0.27––
DP_INT_AUX_C_P0.27––
DP_INT_AUX_NOL––
DP_INT_AUX_POL––
DP_INT_ML_C_N<0>0.27––
DP_INT_ML_C_N<1>0.27––
DP_INT_ML_C_N<2>0.27––
DP_INT_ML_C_N<3>0.27––
DP_INT_ML_C_P<0>0.27––
DP_INT_ML_C_P<1>0.27––
DP_INT_ML_C_P<2>0.27––
DP_INT_ML_C_P<3>0.27––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
ENET_CLKREQ_L0.54––
ENET_RESET_L0.42––
FAN_RT_PWM1.16––
FAN_RT_TACHOL––
GND_5V3V3_AGND0.00––
GND_CHGR_AGND0.00––
GND_DDRREG_SGND0.00––
HDMI_HPD_L0.67––
HDMI_IG_CLK_C_N0.34––
HDMI_IG_CLK_C_P0.34––
HDMI_IG_DATA_C_N<0>0.34––
HDMI_IG_DATA_C_N<1>0.34––
HDMI_IG_DATA_C_N<2>0.34––
HDMI_IG_DATA_C_P<0>0.34––
HDMI_IG_DATA_C_P<1>0.34––
HDMI_IG_DATA_C_P<2>0.34––
HDMI_IG_DDC_CLK0.57––
HDMI_IG_DDC_DATA0.57––
KBDLED_CATHODE10.57––
KBDLED_CATHODE20.57––
LCD_HPD_CONNOL––
LED_RETURN_10.63––
LED_RETURN_20.63––
LED_RETURN_30.63––
LED_RETURN_40.63––
LED_RETURN_50.63––
LED_RETURN_60.63––
LPC_AD<0>0.56––
LPC_AD<1>0.56––
LPC_AD<2>0.56––
LPC_AD<3>0.56––
LPC_CLK33M_LPCPLUS0.63––
LPC_FRAME_L0.56––
LPC_PWRDWN_L0.57––
LPC_SERIRQ0.56––
LPCPLUS_GPIO0.58––
LPCPLUS_RESET_L0.58––
MEMVTT_EN0.52––
NCOL––
P3V3S5_COMP20.73––
P3V3S5_CSN20.14––
P3V3S5_CSP20.72––
P3V3S5_DRVH0.67––
P3V3S5_DRVL0.53––
P3V3S5_EN0.523.400–
P3V3S5_LL0.14––
P3V3S5_RF0.57––
P3V3S5_VBST0.56––
P3V3S5_VFB20.56––
P3V42G3H_BOOST0.62––
P3V42G3H_FB0.71––
P3V42G3H_SW0.31––
P5V3V3_S4_EN0.45––
P5VP3V3_SKIPSEL0.47––
P5VP3V3_VREF20.47––
P5VP3V3_VREG30.55––
P5VS4_COMP10.73––
P5VS4_CSN10.40––
P5VS4_CSP11.16––
P5VS4_DRVH0.93––
P5VS4_DRVL0.52––
P5VS4_LL0.40––
P5VS4_PGOOD0.56––
P5VS4_VBST0.57––
P5VS4_VFB10.56––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.15––
PBUSVSENS_EN_L0.47––
PBUSVSENS_EN_L_DIVOL––
PCIE_AP_D2R_PI_N0.36––
PCIE_AP_D2R_PI_P0.35––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_CONN_N0.37––
PCIE_CLK100M_AP_CONN_P0.37––
PCIE_CLK100M_ENET_N0.37––
PCIE_CLK100M_ENET_P0.37––
PCIE_ENET_D2R_N0.35––
PCIE_ENET_D2R_P0.36––
PCIE_ENET_R2D_C_N0.33––
PCIE_ENET_R2D_C_P0.33––
PCIE_WAKE_L0.61––
PDCINVSENS_EN_L_DIVOL––
PICKB_L0.6764––
PM_CLKRUN_L0.61––
PM_RSMRST_L0.62––
PM_SLP_S3_L0.49––
PM_SLP_S3_R_L0.46––
PM_SLP_S4_L0.50––
PM_THRMTRIP_L_R0.55––
PP_KBD_BOOST_VOUT0.54––
PP0V75_S0_DDRVTT0.14––
PP1V05_S00.01––
PP1V5_S00.36––
PP1V5R1V35_S30.13––
PP3V3_S00.35––
PP3V3_S0_SSD_FLT0.35––
PP3V3_S30.33––
PP3V3_S40.4215––
PP3V3_S50.183.300–
PP3V3_SUS0.43––
PP3V3_TPAD_CONN0.4223––
PP3V3_WLAN_F0.50––
PP3V42_G3H0.313.400–
PP5V_S00.41––
PP5V_S0_HDD_FLT0.40––
PP5V_S30.50––
PP5V_S3_ALSCAMERA_F0.50––
PP5V_S3_LTUSB_A_F0.46––
PP5V_S40.40––
PP5V_S4_CUMULUS0.4517––
PP5V_S50.455.000–
PP5V_SUS–5.000–
PP5V1_CHGR_VDD0.32––
PP5V1_CHGR_VDDP0.32––
PP5VR3V3_SW_LCD0.60––
PP5VR3V3_SW_LCD_UF0.60––
PP18V5_DCIN_CONN_ROL––
PPBUS_G3H0.14012.800–
PPBUS_G3H_R0.16––
PPBUS_S0_LCDBKLT_PWR_SW0.877––
PPBUS_SW_BKL0.877––
PPDCIN_G3H_ISOLOL––
PPVBAT_G3H_CHGR_REG0.140––
PPVIN_G3H_P3V42G3H0.38––
PPVIN_S5_HS_OTHER_ISNS0.15––
PPVOUT_S0_LCDBKLT1.09––
PPVRTC_G3H–3.300–
PPVTTDDR_S30.34––
PSOC_F_CS_L0.7015––
PSOC_MISO0.7013––
PSOC_MOSI0.7017––
PSOC_SCLK0.7021––
S0PGD_BJT_GND_R0.09––
S0PGD_C1.82––
S5_PWRGD0.56––
SD_PWR_EN0.67––
SDCONN_STATE_CHANGE_RIO0.53––
SMBUS_PCH_CLK0.46––
SMBUS_PCH_DATA0.47––
SMBUS_SMC_1_S0_SCL0.54––
SMBUS_SMC_1_S0_SDA0.54––
SMBUS_SMC_2_S3_SCL0.7016––
SMBUS_SMC_2_S3_SDA0.5963––
SMBUS_SMC_5_G3_SCL0.54––
SMBUS_SMC_5_G3_SDA0.53––
SMC_ADAPTER_EN–3.300–
SMC_BC_ACOK0.49––
SMC_BC_ACOK_VCC0.56––
SMC_KBDLED_PRESENT_L4.52––
SMC_OOB1_RX_L0.73––
SMC_OOB1_TX_L0.74––
SMC_PECI_L_R0.73––
SMC_PM_G2_EN0.523.400–
SMC_PROCHOT0.74––
SMC_RESET_L0.49––
SMC_ROMBOOT1.58––
SMC_RX_L0.74––
SMC_TCK0.74––
SMC_TDI0.74––
SMC_TDO0.74––
SMC_THRMTRIP0.74––
SMC_TMS0.74––
SMC_TPAD_RST_L0.46––
SMC_TX_L0.74––
SPI_ALT_CLK0.63––
SPI_ALT_CS_L0.64––
SPI_ALT_MISO0.54––
SPI_ALT_MOSI0.57––
SPI_MLB_CLK0.63––
SPI_MLB_CS_L0.63––
SPI_MLB_MISO0.53––
SPI_MLB_MOSI0.55––
SPI_WP_L0.69––
SPIROM_USE_MLB0.62––
SPKRCONN_L_ID0.70––
SPKRCONN_L_OUT_N0.52––
SPKRCONN_L_OUT_P0.52––
SPKRCONN_R_ID0.51––
SPKRCONN_R_OUT_N0.49––
SPKRCONN_R_OUT_P0.50––
SPKRCONN_SL_OUT_N0.62––
SPKRCONN_SL_OUT_P0.62––
SPKRCONN_SR_OUT_N0.62––
SPKRCONN_SR_OUT_P0.01––
SUS_PGOOD_CT0.63––
SYS_ONEWIRE0.67––
TBTBST_BOOST0.507––
TP_DDRREG_PGOOD0.57––
TP_SMC_MD1OL––
TP_SMC_TRST_LOL––
TP_XDPPCH_HOOK20.00––
TP_XDPPCH_HOOK30.00––
UNCONNECTED_1380.00––
UNCONNECTED_243OL––
UNCONNECTED_300OL––
UNCONNECTED_3040.69––
UNCONNECTED_3080.85––
UNCONNECTED_3090.78––
USB_BT_N0.70––
USB_BT_P0.70––
USB_CAMERA_CONN_N0.55––
USB_CAMERA_CONN_P0.55––
USB_EXTB_N0.51––
USB_EXTB_OC_L0.59––
USB_EXTB_P0.51––
USB_LT1_N0.55––
USB_LT1_P0.57––
USB3_EXTA_RX_F_N0.36––
USB3_EXTA_RX_F_P0.36––
USB3_EXTA_TX_C_NOL––
USB3_EXTA_TX_C_POL––
USB3_EXTB_RX_RC_N0.36––
USB3_EXTB_RX_RC_P0.36––
USB3_EXTB_TX_C_NOL––
USB3_EXTB_TX_C_POL––
VMON_Q2_BASE5.00––
VMON_Q3_BASE0.96––
VMON_Q4_BASE0.84––
WIFI_EVENT_L0.73––
WS_CONTROL_KBD0.4619––
WS_CONTROL_KEY0.46––
WS_KBD_ONOFF_L1.4906––
WS_KBD10.7040––
WS_KBD20.7042––
WS_KBD30.7043––
WS_KBD40.7044––
WS_KBD50.7042––
WS_KBD60.7046––
WS_KBD70.7041––
WS_KBD80.7044––
WS_KBD90.7046––
WS_KBD100.7047––
WS_KBD110.7051––
WS_KBD120.7046––
WS_KBD130.7053––
WS_KBD140.7049––
WS_KBD15_CAP0.8002––
WS_KBD16_NUM0.7039––
WS_KBD170.7039––
WS_KBD180.6989––
WS_KBD190.7043––
WS_KBD200.7052––
WS_KBD210.7058––
WS_KBD220.7052––
WS_KBD230.7065––
WS_LEFT_OPTION_KBDOL––
WS_LEFT_OPTION_KEY0.46––
WS_LEFT_SHIFT_KBD0.4628––
WS_LEFT_SHIFT_KEY0.46––
XDP_DA0_USB_EXTA_OC_L0.52––
XDP_DA1_USB_EXTB_OC_L0.62––
XDP_DA2_USB_EXTC_OC_L0.80––
XDP_DA3_USB_EXTD_OC_L0.67––
XDP_DB0_USB_EXTB_OC_EHCI_L0.00––
XDP_DB1_USB_EXTD_OC_EHCI_L0.62––
XDP_DB2_AP_PWR_EN0.00––
XDP_DB3_SDCONN_STATE_CHANGE0.79––
XDP_DBRESET_L0.60––
XDP_DC0_ISOLATE_CPU_MEM_L0.59––
XDP_DC1_MXM_GOOD0.58––
XDP_DC2_DP_AUXCH_ISOL0.00––
XDP_DC3_SATARDRVR_EN0.65––
XDP_DD0_DP_GPU_TBT_SEL0.99––
XDP_DD1_JTAG_ISP_TCK0.59––
XDP_DD2_AUD_IPHS_SWITCH_EN0.57––
XDP_DD3_ENET_LOW_PWR0.57––
XDP_FC0_MEM_VDD_SEL_1V5_L0.58––
XDP_FC10.00––
XDP_PCH_PWRBTN_L0.00––
XDP_PCH_S5_PWRGD1.31––
XDP_PCH_TCK0.07––
XDP_PCH_TDI0.00––
XDP_PCH_TDO0.00––
XDP_PCH_TMS0.00––
XDPPCH_PLTRST_L0.00––
Z2_CLKIN0.7090––
Z2_CS_L0.7017––
Z2_HOST_INTN0.7017––
Z2_KEY_ACT_L0.7004––
Z2_MISO0.7013––
Z2_MOSI0.7015––
Z2_SCLK0.7018––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3462?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3462: diode 0.140, voltage 12.800. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3462?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3462: diode 0.31, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3462?

OpenBoardData's known-good values for PP5V_S5 on the 820-3462: diode 0.45, voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3462 board?

Open your own 820-3462 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License