Apple laptop board · OpenBoardData

820-3476 known-good readings

Known-good readings for the Apple laptop board 820-3476: 453 nets, including 65 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 65 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3476.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 65 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 7

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.3103.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H — the "G3H" suffix means always-on, from the name, so this is the 3.42 V rail that should be present whenever power is connected, before the board is switched on. Known-good readings in the archive: diode 0.310 to ground and 3.400 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far below 3.4 V points to the rail's supply or a load pulling it down; a diode reading far from 0.310 suggests a short or an open on that net. No known-good resistance reading here, so compare against a matching net or a known-good board.

PP3V42_G3H_SMC_SPVSR0.313.400–
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR — a 3.42 V always-on G3H rail (the "always on" stage comes from the G3H part of the name); the SMC/SPVSR suffix suggests it feeds the SMC's power-sense input, though that's from the name, not board data.

  • Known-good (community archive, guide only): diode 0.31 to ground, voltage 3.400 V.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then apply power and measure the voltage.
  • A diode reading far below 0.31 suggests a short or leaky load on the rail; a voltage well under 3.400 V points to a weak source or excessive loading. No known-good resistance reading is recorded here.
PPBUS_G3H0.16112.500–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main always-on bus rail in the G3H (always-on) startup stage, judging from its name. The archive lists a known-good diode reading of 0.161 and a voltage of 12.500; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.161 usually points to a short or a leaky part on the rail; a missing or low voltage points upstream, toward the adapter/DC-in side rather than the rail itself. No known-good resistance reading is recorded here.

PPDCIN_G3H0.68816.720–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main DC-input rail from the adapter, and the G3H suffix (from the name) marks it as an always-on startup rail. In the readings archive it shows diode 0.688 and voltage 16.720; treat these as a community guide, not a factory spec. Check it with the board unpowered in diode mode from the rail to ground, then with the adapter connected measure the voltage. A diode reading far from 0.688 usually points to a short or a damaged component on that rail, while a missing or low voltage points back toward the adapter input, the input sensing or the isolation circuit. No known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

PPDCIN_G3H_ISOLOL16.720–
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL — the name indicates the isolated DC-input rail in the G3H (always-on) startup stage, i.e. the adapter/DC-in feed before it is switched further into the board. It is listed in the S5 power-rail group.

  • Known-good readings from the archive: diode mode to ground OL, voltage 16.720 V. These are community readings and a guide only; no known-good resistance value is recorded here.
  • Check it with the board unpowered and the adapter removed: meter in diode mode, black probe on ground, red on the rail. Then apply power and measure the DC voltage on the rail.
  • A voltage far below the known-good figure points at the DC-in feed or its input path rather than a downstream rail; an unexpected diode reading (not OL) suggests something on the rail is shorted to ground. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_REG0.16112.500–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From the name, PPVBAT_G3H_CHGR_REG is a G3H always-on rail tied to the charger circuit, likely the battery/charger-regulated supply. The exact parts on it aren't documented here.
  • Known-good readings (community archive, guide only): diode 0.161 to ground, voltage 12.500. No condition is recorded, and there's no known-good resistance value.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; wrong voltage with a normal diode reading points upstream to the charger circuit. These are likely causes, not confirmed ones.
PPVRTC_G3H0.4533.300–
AI: what PPVRTC_G3H is and how to check it
  • What it is: PPVRTC_G3H is the always-on RTC rail; the G3H suffix means always-on, from the name. It's listed as a startup-stage rail and appears in the S5 group at C1910 pin 1.
  • Known-good readings (community guide): diode 0.453 and voltage 3.300. No known-good resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage.
  • If far off: a low diode reading or missing 3.3 V points to a short or a rail not coming up, which can hold off PM_SLP_S4_L. Confirm with a second reading before replacing anything.

S5 and SUS: standby 12

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC–1.200–
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: PP1V2_S5_SMC_VDDC is a 1.2 V rail in the S5 standby domain, judging by its name (S5 = standby, SMC = system management controller supply). The archive gives its nominal voltage as 1.200 V.
  • Known-good readings: only the 1.200 V nominal is listed; there is no known-good diode or resistance value for this rail here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then apply power and measure the voltage at the rail.
  • If it's off: a voltage well below 1.2 V with standby present usually points to the rail's supply or an excessive load on it, but that's a likely cause, not a confirmed one. Compare the diode reading against a matching rail on a known-good board before replacing anything.
PP1V05_SUS0.4251.050–
AI: what PP1V05_SUS is and how to check it

PP1V05_SUS is a 1.05 V standby rail; the SUS/S5 naming (from the name) places it in the standby stage, and the notes list it under S0 as needing PP3V3_S5 → PP3V3_SUS_FET_R. Known-good readings here: diode 0.425 and voltage 1.050, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.425 suggests a short or leaky load on the rail; a voltage far from 1.050 points back at its source or the PP3V3_SUS_FET_R feed. No known-good resistance reading exists for this rail.

PP3V3_S50.1503.300–
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is the 3.3 V standby rail, from its name (S5 = standby, SUS). It appears in the S5 startup list and in the checks for a missing PM_SLP_S4_L.
  • Known-good readings (guide, from community data): diode 0.150 to ground; voltage 3.300. No known-good resistance reading here.
  • How to check: with the board unpowered, diode mode from PP3V3_S5 to ground; then apply power and measure the voltage.
  • If far off: a low diode reading or missing 3.3 V usually points to a short or a failed source feeding the rail, not proof of a bad part. Confirm with a second reading before replacing anything.
PP3V3_S5_AVREF_SMC0.593.200–
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC is a 3.3 V standby rail (S5/SUS stage, from its name) that feeds the SMC's analog reference. Known-good readings in the archive: diode 0.59 to ground, and 3.200 V with power applied.

  • Check it unpowered in diode mode from the rail to ground; a much lower reading than 0.59 suggests a short or leaky part on the rail.
  • Then power the board and measure the voltage; it should sit near 3.200 V once standby is up.
  • A voltage well off 3.200 V with a normal diode reading points upstream, at the standby supply feeding it, rather than at the rail itself.

No known-good resistance reading is recorded for this rail, so compare against a matching standby rail or a known-good board. These are community readings and vary with board state, so treat them as a guide, not a confirmed diagnosis.

PP3V3_S5_SMC_VDDA0.305––
AI: what PP3V3_S5_SMC_VDDA is and how to check it
  • What it is: From the name, a 3.3 V standby (S5) rail feeding the SMC's analog supply (VDDA). It sits in the S5/SUS standby stage.
  • Known-good reading: diode 0.305 (community archive, guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from PP3V3_S5_SMC_VDDA to ground; then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or leaky load on the rail; an open/high reading points to a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_S5RS3RS0_SYSCLKGEN0.1403.300–
AI: what PP3V3_S5RS3RS0_SYSCLKGEN is and how to check it
  • What it is: From the name, PP3V3_S5RS3RS0_SYSCLKGEN is a 3.3 V rail that stays up across S5, S3 and S0 (standby through full run) and feeds the system clock generator. That's general reading of the name, not from board data.
  • Known-good readings (archive, guide only): diode 0.140 to ground, voltage 3.300.
  • How to check: Power off and unplug, then diode mode from the rail to ground. Then power up and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; no voltage at power-on points to the rail's source or its enable, not the clock chip. No known-good resistance reading here; compare against a matching rail or a known-good board.
PP3V3_SUS0.4253.300–
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail, from the "SUS" in its name; it sits at the S5/SUS standby stage and stays up before the board fully powers on. Known-good readings here are diode 0.425 and voltage 3.300, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.425 usually points to a short or leaky load on the rail, while a missing 3.300 V with a normal diode reading points upstream at its source or enable. No known-good resistance reading is listed for this rail.

PP5V_S50.4795.000–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail, a startup-stage rail from its name (S5/SUS = standby). Known-good readings here are diode 0.479 and voltage 5.000; treat these as a community guide, since readings vary with board state.

  • With the board unpowered, measure diode mode from PP5V_S5 to ground; around 0.479 is the reference.
  • With power applied, measure the rail voltage; about 5.000 V is expected.
  • A far-off diode reading usually points to a short or a failed component on the rail; a missing or low voltage points upstream in the standby supply. No known-good resistance value is listed here.
PPBUS_S5_HS_COMPUTING0.16212.500–
AI: what PPBUS_S5_HS_COMPUTING is and how to check it

PPBUS_S5_HS_COMPUTING — reference note

  • What it is: a high-side (HS) switched PPBUS rail that comes up in the S5/SUS standby stage, judging from the name; it's the computing-side PPBUS branch rather than the always-on PPBUS_G3H.
  • Known-good readings (community archive, guide only): diode 0.162 to ground, voltage 12.500. No condition is recorded, and there's no known-good resistance value here.
  • How to check: power off and unplug, then diode-mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; no voltage at all points to the switching source or its enable not coming up. Confirm with a second measurement before replacing anything.
PPBUS_S5_HS_OTHER3V30.16212.500–
AI: what PPBUS_S5_HS_OTHER3V3 is and how to check it
  • What it is: A standby-stage rail (S5/SUS, from the name) on the high-side PPBUS feed; the "OTHER3V3" suffix suggests a 3.3 V branch, but that's from the name only.
  • Known-good readings (community guide): diode 0.162 to ground, voltage 12.500. No known-good resistance value here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure its voltage.
  • Far from known-good: a much lower diode reading usually points to a short or leaky part on the rail; wrong voltage points upstream to the PPBUS feed or its switching. Confirm with a second reading before replacing anything.
PPBUS_S5_HS_OTHER5V0.16212.500–
AI: what PPBUS_S5_HS_OTHER5V is and how to check it
  • What it is: From the name, PPBUS_S5_HS_OTHER5V is a PPBUS high-side rail in the S5 (standby) state, feeding "other" 5V loads. The S5/SUS naming places it in the standby stage.
  • Known-good readings (community archive, a guide only): diode 0.162 to ground, and 12.500 V with power applied. No known-good resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If far off: A diode reading well below 0.162 suggests a short or leaky load on the rail; a missing or low voltage points to the rail not being enabled or its source not switching. Confirm with a second measurement before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP0.2781.075–
AI: what PPVOUT_S5_PCH_DCPSUSBYP is and how to check it
  • What it is: From the name, a standby-stage (S5/SUS) rail feeding the PCH's DCPSUS bypass input. The exact parts on it aren't documented here.
  • Known-good readings (community guide): diode 0.278 to ground, voltage 1.075. No known-good resistance value here.
  • How to check: Power off and unplug, then diode-mode from the rail to ground. Then power up and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a wrong voltage points to its source or enable. Confirm with a second measurement before replacing anything.

S4 7

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.4243.300–
AI: what PP3V3_S4 is and how to check it
  • What it is: PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging by its name; S4 rails come up after the S5 always-on rails and before S3/S0.
  • Known-good readings (community archive, a guide only): diode 0.424 to ground, voltage 3.300.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S4 to ground; then apply power and measure the voltage. No known-good resistance reading is recorded here.
  • If it's far off: a low or shorted diode reading points to a short on the rail; a correct diode reading with no or low voltage points upstream, such as its enable, switch or source rail. Confirm with a second measurement before replacing anything.
PP3V3_S4_TBT0.4243.300–
AI: what PP3V3_S4_TBT is and how to check it

PP3V3_S4_TBT is a 3.3 V rail that comes up at the S4 startup stage, judging by its name (the TBT suffix suggests it feeds Thunderbolt circuitry, though that's general naming, not from this board's data). The archive lists a known-good diode reading of 0.424 and a voltage of 3.300; no condition is recorded for either.

  • With the board unpowered, measure diode mode from PP3V3_S4_TBT to ground and compare with 0.424.
  • Then power the board and confirm about 3.300 V at the rail.

A diode reading far below known-good often points to a short or a failing part on the rail; a missing or low voltage with a normal diode reading points more toward the rail not being enabled or its source not coming up. These are guides from community readings, not confirmed values for every board state.

PP3V3_S4_TBTAPWR0.490––
AI: what PP3V3_S4_TBTAPWR is and how to check it
  • What it is: A 3.3 V S4-stage rail feeding Thunderbolt/Thunderbolt adapter power, judging from the name (S4 = a later startup stage). It isn't described further in the available data.
  • Known-good: diode reading to ground is 0.490 (community reading, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure its voltage.
  • If far off: a much lower diode reading suggests a short on the rail; no voltage at S4 points back to the S4 enable/sequence (e.g. PM_SLP_S4_L and the S4 rails listed). Confirm with a second reading before replacing anything.
PP3V3_S4_TBTBPWR0.384––
AI: what PP3V3_S4_TBTBPWR is and how to check it
  • What it is: a 3.3 V rail in the S4 startup stage, judging by the name (S4 = S4 state, TBTB = Thunderbolt-related, PWR = power). The board data doesn't list which parts sit on it.
  • Known-good: diode reading to ground 0.384 in the readings archive; this is a community guide, not a factory spec. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.384. Then apply power and measure the voltage; it should come up when the board reaches S4.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing voltage with a normal diode reading points more to the rail's enable or supply upstream. No confirmed cause without further measurement.
PP3V3_S4SW_SNS0.4993.300–
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail in the S4 startup stage, judging from its name (S4 = a sleep-state power rail, SW = switched). The archive lists a known-good diode reading of 0.499 and a voltage of 3.300; no condition is recorded with either.

  • With the board unpowered, measure diode mode from the rail to ground; around 0.499 is the guide.
  • With power applied, the rail should sit near 3.300 V once the board reaches S4.
  • A diode reading far below 0.499 usually points to a short or a leaky part on the rail; a missing or low voltage points to the rail not being enabled or its source failing.

These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP5V_S40.4005.100–
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, which is what the name indicates. The archive lists diode 0.400 and voltage 5.100 as known-good readings, with no condition noted, so treat them as a guide only.

  • With the board unpowered, measure diode mode from PP5V_S4 to ground; a far lower reading suggests a short or a leaky part on the rail.
  • Then apply power and measure the voltage; it should sit near 5.1 V once the board reaches S4.
  • A missing or low voltage points upstream to the S4 enable and the S5 rails feeding it, not necessarily to the rail itself.

No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP5V_S4_CUMULUS0.57––
AI: what PP5V_S4_CUMULUS is and how to check it
  • What it is: a 5 V rail that comes up at the S4 startup stage, judged from the name (S4). The data doesn't say which parts sit on it.
  • Known-good: diode 0.57 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage.
  • If far from 0.57: usually a short or a leaky part on the rail, but one reading isn't proof. Compare with a matching rail or a known-good board before replacing anything.

S3: memory 8

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V35_S30.1241.350–
AI: what PP1V35_S3 is and how to check it

PP1V35_S3 is a 1.35 V rail in the S3 (memory) startup stage, judged from its name. The archive gives a known-good diode reading of 0.124 to ground and a voltage of 1.350; no known-good resistance reading here.

  • With the board unpowered, measure diode mode from PP1V35_S3 to ground and compare with 0.124.
  • With power applied, measure the voltage and expect about 1.350 V once the rail is up.
  • A diode reading far below 0.124 suggests a short or leaky load on the rail; far above it suggests an open path. A voltage well off 1.350 V points to the rail not being enabled or its source failing.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PP1V35_S3_CPUDDR0.1241.350–
AI: what PP1V35_S3_CPUDDR is and how to check it

PP1V35_S3_CPUDDR is the 1.35 V memory rail that comes up at the S3 stage, judging by its name (S3 = memory stage; the CPUDDR suffix points to the CPU's DDR supply). Known-good readings for this board are diode 0.124 and voltage 1.350; treat these as a community guide, not a guaranteed value.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.124.
  • With power applied, measure the rail voltage and expect about 1.350 V once the board has reached S3.
  • No known-good resistance reading is recorded here.

A diode reading far below 0.124 usually suggests a short or a leaky load on the rail; a voltage well off 1.350 V at S3 points to the rail's regulator or its enable. Confirm with a second measurement before replacing anything.

PP3V3_S30.5003.300–
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that comes up at the S3 stage, which by its name is the memory stage of startup. The archive lists a known-good diode reading of 0.500 and a voltage of 3.300; treat these as a guide, since readings vary with board state and no condition is recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.500 usually points to a short or a failing load on the rail, while a voltage well under 3.300 suggests the rail isn't being enabled or is being pulled down. No known-good resistance reading is recorded here.

PP3V3_S3RS0_CAMERA0.359––
AI: what PP3V3_S3RS0_CAMERA is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA is a 3.3 V camera rail. The "S3" part of the name puts it in the memory/S3 startup stage, and "CAMERA" says it feeds the camera circuit — both from the name only.
  • Known-good reading: diode 0.359 to ground, from the community archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.359; then power up and measure the rail voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream, to the rail's enable or supply. A small difference can be normal, so confirm before replacing anything.
PP5V_S3_LTUSB_A_ILIM0.51––
AI: what PP5V_S3_LTUSB_A_ILIM is and how to check it
  • What it is: From the name, a 5 V S3 (memory-stage) rail that sets the current limit for a Lightning/USB-A port. The board data lists no parts on it.
  • Known-good: diode 0.51 (community reading, a guide only). No known-good voltage or resistance here.
  • Check: board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • Far off 0.51 in diode mode usually points to a short or a leaky part on that net, but one reading isn't proof.
PP5V_S3RS0_ALSCAM_F0.436––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it
  • What it is: From its name, PP5V_S3RS0_ALSCAM_F is a 5 V rail for the ALS/camera circuit, gated by the S3 (memory) and S0 power states. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.436 to ground (community value, a guide only). No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.436. Then apply power and measure the voltage in S3/S0.
  • If far off: a much lower diode reading suggests a shorted load on the rail; a missing voltage with a good diode reading points upstream to the enabling signal or supply. Neither is confirmed until traced.
PPDDR_S3_REG_R0.110––
AI: what PPDDR_S3_REG_R is and how to check it

PPDDR_S3_REG_R is a memory-rail net in the S3 (suspend-to-RAM) startup stage, judged from its name; the data doesn't list which parts sit on it. Its only known-good reading here is a diode value of 0.110 to ground, with no condition noted, and there is no known-good voltage reading for this net. Check it unpowered in diode mode from the net to ground, then measure its voltage with the board powered and compare against a matching net or a known-good board. A diode reading far from 0.110 usually points to a short or a leaky part on that rail; treat that as a guide, not a confirmed fault.

PPVTTDDR_S30.4960.600–
AI: what PPVTTDDR_S3 is and how to check it
  • What it is: From the name, PPVTTDDR_S3 is the DDR memory termination rail, active in the S3 (memory) startup stage. It's a low-voltage rail, not a main supply.
  • Known-good readings (community archive, guide only): diode 0.496 to ground, voltage 0.600. No known-good resistance value here.
  • How to check: Power off and unplug, then diode-mode from the rail to ground. Then power up and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; no voltage with power applied points to the rail's source or its enable. Confirm with a second measurement before replacing anything.

S0: running 31

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V675_S0_DDRVTT0.1200.600–
AI: what PP0V675_S0_DDRVTT is and how to check it

PP0V675_S0_DDRVTT is a 0.675 V DDR termination rail that runs in the S0 (running) state, judging from its name. The archive lists a known-good diode reading of 0.120 and a voltage of 0.600; treat these as a guide, since readings vary with board state and no condition is recorded.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running.
  • A diode reading far below 0.120 usually points to a short or a leaky part on the rail; a voltage far from 0.600 with power applied points to the rail not coming up or being loaded down.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board if needed.
PP1V05_S00.1251.050–
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V running-state rail, judged from its name: S0 means the board is fully on. The archive lists a known-good diode reading of 0.125 and a voltage of 1.050; treat these as a guide only, since readings vary with board state. With the board unpowered, measure diode mode from PP1V05_S0 to ground and compare with 0.125. Then power up and confirm about 1.050 V. A large deviation in diode mode usually points to a short or an open on that net, but one reading alone doesn't confirm a bad part; no known-good resistance value is recorded here.

PP1V5_S00.3431.050–
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail in the S0 (running) stage, judging from its name. The archive lists a known-good diode reading of 0.343 to ground and a voltage of 1.050 V; the voltage condition isn't recorded, and no known-good resistance value is listed here.

  • With the board unpowered, measure diode mode from PP1V5_S0 to ground and compare with 0.343.
  • With power applied, measure the rail voltage and compare with 1.050 V.

A diode reading far below 0.343 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken path. A voltage well off 1.050 V points to the rail's supply or its enable, not the load. These are guides from community readings, not confirmed limits.

PP1V5_S0_AUDIO_DIG0.379––
AI: what PP1V5_S0_AUDIO_DIG is and how to check it
  • What it is: A 1.5 V digital audio rail that runs in the S0 (board fully on) state, judged from the name. It isn't listed among the S0 rails in the community notes, so its role is inferred from the name only.
  • Known-good reading: diode 0.379 to ground, from the readings archive. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.379; then power up and measure the DC voltage, expecting about 1.5 V.
  • If it's far off: a much lower diode reading suggests a shorted load on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. Treat the 0.379 as a guide only, since readings vary with board state.
PP1V05_S0_PCH_VCC_ICC0.126––
AI: what PP1V05_S0_PCH_VCC_ICC is and how to check it
  • What it is: A 1.05 V S0 (running-stage) rail feeding the PCH's VCC_ICC supply, judging from the name; the exact loads on it aren't documented here.
  • Known-good: diode reading to ground of 0.126 (community guide, board state not stated). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, which should sit near 1.05 V.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a missing voltage points to the rail's regulator or its enable. Confirm with a second reading before replacing anything.
PP1V05_S0_PCH_VCC_ICC_R0.126––
AI: what PP1V05_S0_PCH_VCC_ICC_R is and how to check it
  • What it is: From the name, a 1.05 V S0 (running-state) rail feeding the PCH's VCC_ICC domain. It appears in the S0 group of rails.
  • Known-good reading: diode 0.126 to ground (community archive value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the DC voltage, which should be about 1.05 V.
  • If far off: a much lower diode reading suggests a short on the rail; no voltage at S0 points to the rail's enable or source, not the PCH itself. Confirm with a second reading before replacing anything.
PP1V05_S0_PCH_VCCACLKPLL0.126––
AI: what PP1V05_S0_PCH_VCCACLKPLL is and how to check it

PP1V05_S0_PCH_VCCACLKPLL — from the name, a 1.05 V rail feeding the PCH's ACLK PLL; the S0 suffix places it in the running stage, so it should only be up once the board is fully on.

  • Known-good: diode 0.126 (community reading, a guide only). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.126 usually points to a short or a damaged load on the rail; a missing voltage with a normal diode reading points upstream, to the rail's enable or supply.
  • No voltage reference is available, so compare against a known-good board if you can.
PP1V05_S0_PCH_VCCAPLL_OPI0.126––
AI: what PP1V05_S0_PCH_VCCAPLL_OPI is and how to check it
  • What it is: From the name, a 1.05 V S0 (running-stage) rail feeding the PCH's VCCAPLL OPI supply. It's listed under S0 rails, so it should come up only once the board is in the running state.
  • Known-good: The archive gives a diode reading of 0.126 to ground. There is no known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.126. Then apply power and measure the voltage; expect about 1.05 V once the board is in S0.
  • If it's far off: A diode reading well below 0.126 suggests a short on the rail; a missing voltage with a normal diode reading points to the rail's supply or enable, not the load. Readings vary with board state, so treat 0.126 as a guide, not a pass/fail limit.
PP1V05_S0_REG_R0.130––
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R — a 1.05 V S0 (running-state) regulated rail; the S0 stage comes from the name.

  • Known-good: diode-to-ground 0.130 (community reading, a guide only; no condition recorded). No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe to ground, red to the rail. Then power up and measure the voltage.
  • A diode reading far from 0.130 usually points to a short or a leaky load on the rail rather than the regulator itself; confirm with a second reading before replacing anything.
PP1V5_S0SW_AUDIO_HDA0.342––
AI: what PP1V5_S0SW_AUDIO_HDA is and how to check it
  • What it is: A 1.5 V switched audio/HDA rail. The S0 in the name indicates it belongs to the running (S0) state, and SW indicates it is switched on by a control signal rather than always present. This is from the rail name, not from board data.
  • Known-good reading: diode 0.342 to ground, from the readings archive. No known-good voltage reading is listed here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.342. Then power the board and confirm the rail comes up only in S0, alongside PP1V5_S0.
  • If it's far off: a much lower diode reading suggests a short or a failing load on the rail; a missing voltage with a normal diode reading points to the switch or its enable. These are general guidelines, not confirmed causes.
PP1V05_S0SW_PCH_HSIO0.2111.050–
AI: what PP1V05_S0SW_PCH_HSIO is and how to check it

PP1V05_S0SW_PCH_HSIO is a 1.05 V S0 (running) rail feeding the PCH's high-speed I/O, as the name suggests. The archive lists a known-good diode reading of 0.211 and a voltage of 1.050; treat these as a guide, since readings vary with board state. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode value far from 0.211 suggests a short or leaky part on the rail; a voltage well off 1.050 with the board in S0 points to the rail not coming up or being loaded down. No known-good resistance reading is listed here.

PP1V05_S0SW_PCH_VCCSATA3PLL0.208––
AI: what PP1V05_S0SW_PCH_VCCSATA3PLL is and how to check it
  • What it is: From its name, a 1.05 V S0 (running-state) rail feeding the PCH's SATA 3 PLL supply. It appears in the S0 group of rails.
  • Known-good reading: diode 0.208 to ground. That is the only known-good value recorded here; no known-good voltage is listed.
  • How to check: with the board powered off, measure diode mode from the rail to ground and compare with 0.208. Then power up and measure the voltage; it should sit near 1.05 V by the name, but that figure is general, not from this board's data.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no voltage points upstream, to the rail's regulator or its enable. Confirm with a second measurement before replacing anything.
PP1V05_S0SW_PCH_VCCUSB3PLL0.2091.050–
AI: what PP1V05_S0SW_PCH_VCCUSB3PLL is and how to check it

PP1V05_S0SW_PCH_VCCUSB3PLL — reference note

  • This is a 1.05 V rail feeding the PCH's USB 3.0 PLL section; the "S0" in the name marks it as a running-state rail, and "SW" suggests it is switched on by a control signal rather than always present.
  • Known-good readings from the archive: diode 0.209 to ground, and 1.050 V with the board powered in S0. These are community figures and a guide only.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.209. Then apply power, let the board reach S0, and measure the voltage — expect about 1.050 V.
  • A diode reading far below 0.209 suggests a short or a leaky load on the rail; a correct diode reading with no voltage points instead to the rail not being enabled or its source missing. No known-good resistance reading is available for this rail.
PP3V3_S00.3593.300–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that comes up at the S0 (running) stage, judging from its name. Known-good readings in the archive: diode 0.359 to ground and 3.300 V with the board powered. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.359 suggests a short or leaky load on the rail; correct voltage but no boot points elsewhere in the sequence. No known-good resistance reading is recorded here.

PP3V3_S0_AUDIO_ANALOG0.343––
AI: what PP3V3_S0_AUDIO_ANALOG is and how to check it
  • What it is: From its name, a 3.3 V analog audio rail that comes up in the S0 (running) state. The data doesn't list which parts sit on it.
  • Known-good: diode 0.343 to ground. No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from the rail to ground and compare with 0.343. Then power on and measure the DC voltage; it should be near 3.3 V.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a correct diode reading with no voltage points back to the rail's source or enable. Treat this as a guide, not a confirmed fault.
PP3V3_S0_FET0.3593.000–
AI: what PP3V3_S0_FET is and how to check it

PP3V3_S0_FET is a 3.3 V rail in the S0 (running) power state, judging by its name. The archive gives a known-good diode reading of 0.359 and a voltage of 3.000 V; these are community readings and only a guide.

  • With the board unpowered, measure diode mode from PP3V3_S0_FET to ground and compare with 0.359.
  • With power applied, measure the rail voltage and compare with 3.000 V.
  • A reading far from these usually points to a short or a rail that isn't coming up, but one reading doesn't confirm a bad part. No known-good resistance value is listed here.
PP3V3_S0SW_SSD0.5693.300–
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD — reference note

  • This is a 3.3 V rail that switches on in the S0 (running) state, based on the name: the "S0" means running state and "SSD" means it feeds the SSD. The "SW" suggests it is a switched rail, generally meaning a FET gates it from a parent rail.
  • Known-good readings from the archive: diode 0.569 to ground, voltage 3.300. These are community values and a guide only, since they vary with board state.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage, expecting about 3.3 V once the board is in S0.
  • A diode reading far from 0.569 usually points to a short or a leaky part on the rail; a correct diode reading with no voltage points to the switch or its enable, not the load. No known-good resistance reading is available here.
PP3V3_S0SW_SSD_FET0.5693.300–
AI: what PP3V3_S0SW_SSD_FET is and how to check it

PP3V3_S0SW_SSD_FET — an S0 (running-state) 3.3 V rail switched through a FET, feeding the SSD; the S0 stage and FET switching are from the name.

  • Known-good readings (community archive, guide only): diode 0.569 to ground, voltage 3.300 V.
  • Check with the board unpowered: diode mode, red probe to ground, black to the rail. Then power up and measure the voltage.
  • A voltage well below 3.3 V in S0 points to the switch FET or its enable not turning on; a diode reading far from 0.569 suggests a short or open on the rail. No known-good resistance reading here — compare against a matching rail or a known-good board.
  • A likely cause isn't a confirmed one; check the enable side of the FET before replacing anything.
PP3V3_S0SW_SSD_FLT0.5693.300–
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a switched 3.3 V rail for the SSD, active in the S0 (running) state, judging from its name. Known-good readings here are diode 0.569 and voltage 3.300; no condition is recorded, so treat them as a guide.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.569.
  • With power applied and the board in S0, measure the voltage; it should sit near 3.300 V.
  • A far-off diode reading usually points to a short or a damaged component on the rail; a missing or low voltage points to the rail not being enabled or its source failing. No known-good resistance reading is available for this rail.
PP5V_S00.4375.099–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is a 5 V rail that comes up in the S0 (running) state, judged from its name. The archive lists a known-good diode reading of 0.437 to ground and a running voltage of 5.099 V; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.437 usually points to a short or a failing load on the rail; a voltage well off 5.099 V with the board in S0 points to the rail's supply or enable. No known-good resistance reading is listed here.

PP5V_S0_BKLT_A0.40––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A — from the name, a 5 V backlight rail that comes up in the S0 (running) state.

  • Known-good: diode 0.40 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage.
  • A diode reading far from 0.40 usually points to a short or a leaky part on that rail; a missing or low voltage with a normal diode reading points upstream, such as the enable or the source rail feeding it.
  • The backlight notes for this board suggest checking the backlight output voltage and the enable on U7701 pin 3, but they don't give a known-good figure for this rail.
PP5V_S0_BKLT_D0.40––
AI: what PP5V_S0_BKLT_D is and how to check it
  • What it is: A 5 V backlight rail in the S0 (running) state, judged from the name; it feeds the display backlight section. The archive lists it under backlight diagnostics, not in the main S0 rail list.
  • Known-good: diode reading to ground 0.40 (board unpowered, diode mode). No known-good voltage reading here.
  • How to check: power off, measure diode mode from PP5V_S0_BKLT_D to ground and compare with 0.40. Then power on and measure the voltage; the backlight notes say below 1 V usually points to a bad fuse or MOSFET, and 8.4 V is the expected backlight output level to look for.
  • If far off: a short or open in the rail's feed, fuse or switching MOSFET is the usual suspect, but that's general guidance, not confirmed for this board.
PP5V_S0_CPUVR_VDD0.405.095–
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD is a 5 V supply for the CPU voltage-regulator section, enabled in the S0 (running) state — that's from the rail's name. The archive lists a known-good diode reading of 0.40 and a voltage of 5.095 V; these are community readings and only a guide, and there's no known-good resistance value here.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.40.
  • With power applied in S0, measure the voltage and compare with 5.095 V.

A diode reading far below 0.40 usually points to a short or a failing part on the rail; a voltage well off 5.095 V points to the supply or its enable not coming up. Confirm with a second measurement before replacing anything.

PP5V_S0_FET0.4375.000–
AI: what PP5V_S0_FET is and how to check it
  • What it is: PP5V_S0_FET is a 5 V rail in the S0 (running) stage, judging from its name; the FET suffix suggests it's the switched output of a 5 V load switch or pass FET feeding S0 circuitry. The archive doesn't list which parts sit on it.
  • Known-good readings (community guide): diode 0.437 to ground, voltage 5.000 V with the board running. No known-good resistance value here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a low diode reading or missing 5 V usually points to a shorted load or a failed switch/FET or its enable, but that's a likely cause, not confirmed. Compare against a matching rail or a known-good board before replacing anything.
PP5V_S0_KBDBKLT_SW0.40––
AI: what PP5V_S0_KBDBKLT_SW is and how to check it

PP5V_S0_KBDBKLT_SW is a switched 5 V keyboard-backlight rail; the S0 in the name marks it as a running-state rail, and KBDBKLT_SW indicates it is the switched feed to the keyboard backlight. The only known-good figure here is a diode reading of 0.40, with no condition recorded; no known-good voltage is listed. With the board unpowered, measure diode mode from the rail to ground and compare with 0.40, then power up and check the voltage appears only in S0. A diode reading far below 0.40 suggests a short or leaky load on the rail, while a missing voltage in S0 points back to its enable or switch circuit; treat the 0.40 as a guide only.

PPVCC_S0_CPU0.0571.800–
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail, active in the S0 (running) state — that's from the rail's name. The archive lists a known-good diode reading of 0.057 to ground and a voltage of 1.800; these are community readings and only a guide, and no condition is recorded for them. Check it unpowered in diode mode to ground first, then power the board and measure the voltage. A diode reading far from 0.057 can suggest a short or a damaged CPU/rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything.

PPVCC_S0_CPU_PH10.057––
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 — the name indicates a CPU core power phase (PH1) rail, active in the S0 (running) state. It's the switching node/output of one CPU VRM phase, so treat it as a high-current rail.

  • Known-good from the archive: diode mode to ground 0.057 (board unpowered). No known-good voltage reading is recorded here.
  • Check it with power off: diode mode, red probe to ground, black to the rail, and compare against 0.057.
  • Then power on and measure DC volts on the rail; compare with a matching phase or a known-good board, since no voltage value is listed.
  • A diode reading far below known-good usually points to a shorted load or FET on that phase; far above can mean an open connection. Confirm with a second measurement before replacing anything.
PPVCC_S0_CPU_PH20.057––
AI: what PPVCC_S0_CPU_PH2 is and how to check it
  • What it is: From its name, PPVCC_S0_CPU_PH2 is a CPU core power rail (VCC CPU, phase 2) active in the S0 running state. It's one phase of the CPU VRM output.
  • Known-good reading: The archive lists a diode value of 0.057 for this net. No known-good voltage reading is recorded here.
  • How to check: With the board unpowered, measure diode mode from PPVCC_S0_CPU_PH2 to ground. Then power up and measure the voltage on the rail.
  • If far from known-good: A diode reading well off 0.057 points to a short or open around the CPU VRM phase or the CPU itself, but one reading isn't proof. Compare with the other CPU phases and a known-good board before replacing anything.
PPVIN_S0_CPUVR_VIN0.1512.580–
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN — the name indicates the CPU voltage-regulator input rail, active in the S0 (running) state.

  • Known-good readings from the archive: diode 0.15 to ground, voltage 12.580 with the board running.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A diode reading far from 0.15 suggests a short or a damaged component on that rail; a voltage far from 12.580 points to a supply or enable problem upstream.
  • No known-good resistance value is recorded for this rail.
PPVIN_S0SW_LCDBKLT0.87––
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the switched backlight input rail; the S0 in the name indicates it belongs to the running state, and the name suggests it feeds the LCD backlight boost circuit. The only known-good reading in the archive is a diode value of 0.87 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on it. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.87 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PPVIN_S0SW_LCDBKLT_R0.14––
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail: the "S0" in the name marks it as a running-state supply, and "LCDBKLT" points to the display backlight circuit. The only known-good figure here is a diode reading of 0.14 to ground, with no condition recorded; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.14 usually points to a short or a leaky part on the rail, but a single reading isn't proof of a bad part.

Repair notes

Backlight

Diagnosing

Check your voltage on backlight output. If below 1V probably a bad fuse or MOSFET. If 8.4V check EN signal on U7701 pin 3, if present, check BKL_PWM, if > 1V then replace U7701

Power Rails

S5

PPBUS_G3H PPBUS_S5_HS_COMPUTING_ISNS PPBUS_S5_HS_OTHER_ISNS PPDCIN_G3H_ISOL PP3V42_G3H PPVRTC_G3H C1910 pin 1 PP5V_S5 PP3V3_S5

S4/S3

PP5V_S4RS3 PP3V3_S4SW_SNS PP3V3_S4 PP3V3_S3 PP1V8_S3 PP1V2_S3

S0

PP1V05_SUS ( needs PP3V3_S5 -> PP3V3_SUS_FET_R ) PP5V_S0 PP3V3_S0 PP3V3_S0SW_SSD PP1V5_S0 PP0V6_S0_DDRVTT PP1V05_S0 PP1V05_S0SW_PCH_HSIO PPVCC_S0_CPU PPHV_S0SW_LCDBKLT

Missing PM_SLP_S4_L

Missing PM_SLP_S4_L can sometimes be diagnosed by going through and ensuring all the following signals are present; PPVRTC_G3H RTC_RESET_L PCH_SRTCRST_L PCH_INTVRMEN PCH_DSWVRMEN PCH_CLK32K_RTCX1 PP3V3_S5 PM_DSW_PWRGD PP3V3_SUS PM_BATLOW_L PM_RSMRST_L PM_PWRBTN_L

Every net with a reading

NetDiodeVoltageResistance
4V5_NR0.680––
4V5_REG_EN0.746––
4V5_REG_IN0.431––
ADAPTER_SENSE0.5973.3–
ALL_SYS_PWRGD0.4303.4–
AP_PCIE_WAKE_L0.522––
AP_S0IX_WAKE_L0.479––
AP_S0IX_WAKE_SEL0.495––
AUD_CH_HS_GND0.001––
AUD_CONN_HP_LEFT1.088––
AUD_CONN_TIPDET_20.923––
AUD_CONN_TYPEDET0.778––
AUD_HP_PORT_L1.108––
AUD_HP_PORT_R1.520––
AUD_HP_PORT_REFCH0.002––
AUD_HP_PORT_REFUS0.002––
AUD_HSBIAS0.558––
AUD_HSBIAS_FILT0.767––
AUD_HSBIAS_IN0.500––
AUD_HSBIAS_REF0.492––
AUD_LO2_L_N0.694––
AUD_LO2_L_P0.695––
AUD_LO2_R_N0.694––
AUD_LO2_R_P0.696––
AUD_LO3_L_N0.679––
AUD_LO3_L_P0.680––
AUD_LO3_R_N0.678––
AUD_LO3_R_P0.680––
AUD_SPKRAMP_LIN_N0.694––
AUD_SPKRAMP_LIN_P0.696––
AUD_SPKRAMP_LSUBIN_N0.679––
AUD_SPKRAMP_LSUBIN_P0.680––
AUD_SPKRAMP_RIN_N0.695––
AUD_SPKRAMP_RIN_P0.696––
AUD_SPKRAMP_RSUBIN_N0.679––
AUD_SPKRAMP_RSUBIN_P0.680––
AUD_TIPDET_1OL––
AUD_TIPDET_21.081––
AUD_TYPEDET0.777––
AUD_US_HS_GND0.001––
BKLT_EN_R0.53––
BKLT_ISET_KEYB0.67––
BKLT_KEYB10.64––
BKLT_KEYB20.64––
BKLT_PWM_KEYB0.53––
BKLT_SCL0.53––
BKLT_SD0.57––
BKLT_SDA0.53––
BKLT_SENSE_OUT0.73––
CAM_SENSOR_WAKE_L_CONN0.00––
CHGR_ACIN0.5523.9–
CHGR_AGATE0.63––
CHGR_AGATE_DIVOL––
CHGR_AMON0.70––
CHGR_BGATE0.642––
CHGR_BMON0.71––
CHGR_BOOT0.554––
CHGR_CELL0.69––
CHGR_CSI_N0.567––
CHGR_CSI_P0.561––
CHGR_CSO_N0.137––
CHGR_CSO_P0.139––
CHGR_DCIN0.6116.23–
CHGR_DCIN_D_R0.60216.480–
CHGR_ICOMP0.720–
CHGR_LGATE.447––
CHGR_PHASE0.135––
CHGR_RST_L0.49––
CHGR_SGATE0.617––
CHGR_UGATE0.57––
CHGR_VCOMP0.71––
CHGR_VFRQ0.470–
CHGR_VNEG0.52––
CODEC_FLYNOL––
CODEC_FLYP0.447––
CODEC_HS_MIC_N0.769––
CODEC_HS_MIC_P0.769––
CODEC_MICIN20.718––
CODEC_VCOM0.713––
CODEC_VREF_ADC0.776––
CPU_PROCHOT_L0.200.056–
CPU_RTN0.000.000–
CPU_VCCST_PWRGD0.740––
CPU_VIDALERT_L0.211.057–
CPU_VIDSCLK0.191.031–
CPU_VIDSOUT0.201.049–
CPU_VR_EN0.321.064–
CPU_VR_READY0.531.058–
CPUVR_BOOT10.606.201–
CPUVR_BOOT20.5946.198–
CPUVR_COMP0.571.397–
CPUVR_DRSEL0.000.000–
CPUVR_FB0.541.737–
CPUVR_FB20.551.744–
CPUVR_FCCM0.575.062–
CPUVR_IMON0.570.057–
CPUVR_ISEN10.58––
CPUVR_ISEN20.58––
CPUVR_ISUMN_R0.361.746–
CPUVR_ISUMP0.481.746–
CPUVR_LGATE10.434.252–
CPUVR_LGATE20.4294.269–
CPUVR_NTC0.582.169–
CPUVR_PGOOD_R0.70––
CPUVR_PHASE10.0571.739–
CPUVR_PHASE20.0571.740–
CPUVR_PROG10.580.000–
CPUVR_PROG20.570.000–
CPUVR_PROG30.580.000–
CPUVR_PWM10.570.785–
CPUVR_PWM20.570.779–
CPUVR_SLOPE0.580.290–
CPUVR_UGATE10.6202.293–
CPUVR_UGATE20.6192.280–
CS4208_HDA_SDOUT0_R0.467––
CS4208_SPDIF_IN0.001––
CS4208_SPDIF_OUT0.703––
DCINVSENS_EN_L0.470––
DDRREG_1V8_VREF0.63––
DDRREG_DRVH0.57––
DDRREG_DRVL0.43––
DDRREG_EN0.53––
DDRREG_FB0.68––
DDRREG_LL0.11––
DDRREG_MODE0.52––
DDRREG_PGOOD0.49––
DDRREG_TRIP0.74––
DDRREG_VBST0.60––
DDRREG_VDDQSNS0.12––
DDRREG_VTTSNS0.16––
DFET_OPENCH0.477––
DFET_OPENUS0.477––
DMIC_CLK30.834––
DMIC_CLK3_R0.748––
DMIC_SDA20.001––
DMIC_SDA30.784––
DP_A_LSX_ML_N<1>0.769––
DP_A_LSX_ML_P<1>0.763––
DP_B_LSX_ML_N<1>0.762––
DP_B_LSX_ML_P<1>0.759––
DP_TBTPA_AUXCH_N0.815––
DP_TBTPA_AUXCH_P0.815––
DP_TBTPA_DDC_CLK0.581––
DP_TBTPA_DDC_DATA0.583––
DP_TBTPA_HPD0.796––
DP_TBTPA_ML_N<1>0.776––
DP_TBTPA_ML_P<1>0.776––
DP_TBTPB_AUXCH_N0.763––
DP_TBTPB_AUXCH_P0.764––
DP_TBTPB_DDC_CLK0.574––
DP_TBTPB_DDC_DATA0.574––
DP_TBTPB_HPD0.779––
DP_TBTPB_ML_N<1>0.775––
DP_TBTPB_ML_P<1>0.773––
EDP_BKLT_EN0.68––
EDP_BKLT_PSR_EN0.53––
EDP_PANEL_PWR0.68––
EDP_PANEL_PWR_OR_PSR_EN0.67––
FAN_RT_PWM0.90––
FAN_RT_TACHOL––
GND_AUDIO_CODEC0.000––
GPIO0_SPKR_SHUTDOWN0.534––
HDA_BIT_CLK0.501––
HDA_RST_L0.500––
HDA_SDIN00.441––
HDA_SYNC0.501––
I2C_CAM_SCK0.76––
I2C_CAM_SDA0.76––
ISNS_1V05_S0_N0.130––
ISNS_1V05_S0_P0.130––
ISNS_LCDBKLT_N0.14––
ISNS_LCDBKLT_P0.14––
ISNS_S0_SSD_IOUT0.710––
ISNS_SSD_N0.569––
ISNS_SSD_P0.569––
ISNS_TBT_NOL––
ISNS_TBT_POL––
LCD_PSR_EN0.58––
LCDBKLT_EN_L0.00––
LCDBKLT_FB0.72––
LCDBKLT_FET_DRV0.49––
LCDBKLT_SW0.42––
LPC_AD<0>0.56––
LPC_AD<1>0.56––
LPC_AD<2>0.56––
LPC_AD<3>0.56––
LPC_CLK24M_LPCPLUS0.49––
LPC_FRAME_L0.56––
LPC_PWRDWN_L0.660––
LPC_SERIRQ0.56––
LPCPLUS_RESET_L0.57––
MEMVTT_PWR_EN0.53––
MIPI_CLK_CONN_N0.40––
MIPI_CLK_CONN_P0.40––
MIPI_DATA_CONN_N0.40––
MIPI_DATA_CONN_P0.40––
P1V2_CAM_SRVLXC_PHASE0.338––
P1V5_S0_FB0.77––
P1V5_S0_SW0.3431.050–
P1V05_S0_VREF0.62––
P1V05S0_DRVH0.59––
P1V05S0_DRVH_R0.59––
P1V05S0_DRVL0.46––
P1V05S0_EN0.43––
P1V5S0_EN0.73––
P1V05S0_FB0.68––
P1V05S0_LL0.13––
P1V05S0_MODE0.52––
P1V05S0_PGOOD0.48––
P1V5S0_PGOOD0.55––
P1V05S0_TRIP0.74––
P1V05S0_VBST0.60––
P1V05S0_VDDQSNS0.14––
P1V05S0_VTT0.55––
P1V05S0_VTTREF0.48––
P1V5S0SW_AUDIO_ENOL––
P1V05S3_EN0.49––
P1V35_CAM_SRVLXD_PHASE0.281––
P3V3S0_EN_D0.568––
P3V3S0SW_SSD_FET_RAMP0.635––
P3V3S5_COMP20.73––
P3V3S5_CSN20.143.300–
P3V3S5_CSP21.293.300–
P3V3S5_CSP2_R–3.300–
P3V3S5_DRVH0.673.300–
P3V3S5_DRVL0.52––
P3V3S5_LL0.143.300–
P3V3S5_RF0.58––
P3V3S5_TG–3.300–
P3V3S5_VBST0.558.250–
P3V3S5_VFB20.57––
P3V3SUS_EN0.6143.300–
P5VP3V3_SKIPSEL0.48––
P5VP3V3_VREF20.48––
P5VP3V3_VREG30.563.200–
P5VS4_COMP10.73––
P5VS4_CSN10.40––
P5VS4_CSP11.30––
P5VS4_DRVH0.94––
P5VS4_DRVL0.52––
P5VS4_LL0.40––
P5VS4_VBST0.62––
P5VS4_VFB10.58––
P5VS4_VSW0.400––
P5VS4RS3_EN0.49––
P5VS4RS3_PGOOD0.49––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.1412.490–
PBUSVSENS_EN_L0.4912.260–
PBUSVSENS_EN_L_DIVOL12.380–
PCH_CLK32K_RTCX10.46––
PCH_DSWVRMEN–3.200–
PCIE_AP_R2D_C_N0.390––
PCIE_AP_R2D_C_P0.387––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_WAKE_L0.512––
PD_CS4208_GPIO10.750––
PICKB_L0.69––
PLT_RESET_L0.551––
PLT_RST_BUF_L0.560––
PM_CLKRUN_L0.59––
PM_PWRBTN_L0.5653.400–
PM_RSMRST_LOL3.200–
PM_S0_PGOOD0.66––
PM_SLP_S3_BUF_L0.43––
PM_SLP_S3_L0.6543.300–
PM_SLP_S3_R_L0.67––
PM_SLP_S4_L0.5013.300–
PM_SLP_S5_L0.4523.300–
PM_SLP_SUS_L0.6163.300–
PP0V675_S0_DDRVTT0.1200.600–
PP1V2_CAM0.338––
PP1V2_CAM_PCIE_PVDD_FLT0.356––
PP1V2_CAM_PCIE_VDD_FLT0.356––
PP1V2_CAM_XTALPCIEVDD0.356––
PP1V2_S5_SMC_VDDC–1.200–
PP1V05_S00.1251.050–
PP1V5_S00.3431.050–
PP1V5_S0_AUDIO_DIG0.379––
PP1V05_S0_PCH_VCC_ICC0.126––
PP1V05_S0_PCH_VCC_ICC_R0.126––
PP1V05_S0_PCH_VCCACLKPLL0.126––
PP1V05_S0_PCH_VCCAPLL_OPI0.126––
PP1V05_S0_REG_R0.130––
PP1V5_S0SW_AUDIO_HDA0.342––
PP1V05_S0SW_PCH_HSIO0.2111.050–
PP1V05_S0SW_PCH_VCCSATA3PLL0.208––
PP1V05_S0SW_PCH_VCCUSB3PLL0.2091.050–
PP1V05_SUS0.4251.050–
PP1V8_CAM0.504––
PP1V35_CAM0.280––
PP1V35_DDR_CLK0.280––
PP1V35_S30.1241.350–
PP1V35_S3_CPUDDR0.1241.350–
PP3V3_S00.3593.300–
PP3V3_S0_AUDIO_ANALOG0.343––
PP3V3_S0_FET0.3593.000–
PP3V3_S0SW_SSD0.5693.300–
PP3V3_S0SW_SSD_FET0.5693.300–
PP3V3_S0SW_SSD_FLT0.5693.300–
PP3V3_S30.5003.300–
PP3V3_S3RS0_CAMERA0.359––
PP3V3_S40.4243.300–
PP3V3_S4_TBT0.4243.300–
PP3V3_S4_TBTAPWR0.490––
PP3V3_S4_TBTBPWR0.384––
PP3V3_S4SW_SNS0.4993.300–
PP3V3_S50.1503.300–
PP3V3_S5_AVREF_SMC0.593.200–
PP3V3_S5_SMC_VDDA0.305––
PP3V3_S5RS3RS0_SYSCLKGEN0.1403.300–
PP3V3_SUS0.4253.300–
PP3V3_TBTLC0.4163.300–
PP3V3_TPAD_CONN0.43––
PP3V42_G3H0.3103.400–
PP3V42_G3H_SMC_SPVSR0.313.400–
PP4V5_AUDIO_ANALOG0.435––
PP5V_S00.4375.099–
PP5V_S0_BKLT_A0.40––
PP5V_S0_BKLT_D0.40––
PP5V_S0_CPUVR_VDD0.405.095–
PP5V_S0_FET0.4375.000–
PP5V_S0_KBDBKLT_SW0.40––
PP5V_S3_LTUSB_A_ILIM0.51––
PP5V_S3RS0_ALSCAM_F0.436––
PP5V_S40.4005.100–
PP5V_S4_CUMULUS0.57––
PP5V_S50.4795.000–
PP5V1_CHGR_VDD0.313––
PP5V1_CHGR_VDDP0.31––
PP5VR3V3_SW_LCD0.52––
PP5VR3V3_SW_LCD_UF0.52––
PP15V_TBT0.566––
PPBUS_G3H0.16112.500–
PPBUS_S5_HS_COMPUTING0.16212.500–
PPBUS_S5_HS_OTHER3V30.16212.500–
PPBUS_S5_HS_OTHER5V0.16212.500–
PPDCIN_G3H0.68816.720–
PPDCIN_G3H_ISOLOL16.720–
PPDDR_S3_REG_R0.110––
PPVBAT_G3H_CHGR_REG0.16112.500–
PPVCC_S0_CPU0.0571.800–
PPVCC_S0_CPU_PH10.057––
PPVCC_S0_CPU_PH20.057––
PPVIN_S0_CPUVR_VIN0.1512.580–
PPVIN_S0SW_LCDBKLT0.87––
PPVIN_S0SW_LCDBKLT_R0.14––
PPVIN_SW_LCDBKLT_SW0.870––
PPVIN_SW_TBTBST0.525––
PPVOUT_BKLT_FB20.60––
PPVOUT_S5_PCH_DCPSUSBYP0.2781.075–
PPVRTC_G3H0.4533.300–
PPVTTDDR_S30.4960.600–
PSOC_F_CS_L0.72––
PSOC_MISO0.72––
PSOC_MOSI0.72––
PSOC_SCLK0.72––
S5_PWR_EN0.533.400–
S5_PWRGD0.573.300–
SMBUS_SMC_1_S0_SCL0.58––
SMBUS_SMC_1_S0_SDA0.58––
SMBUS_SMC_2_S3_SCL0.75––
SMBUS_SMC_2_S3_SDA0.75––
SMBUS_SMC_5_G3_SCL0.513.300–
SMBUS_SMC_5_G3_SDA0.513.300–
SMC_ADAPTER_EN0.6103.300–
SMC_BC_ACOK0.523.300–
SMC_DELAYED_PWRGD0.69––
SMC_MANUAL_RST_L0.662.700–
SMC_ONOFF_L0.653.400–
SMC_PM_G2_EN0.5543.400–
SMC_PROCHOT0.74––
SMC_RESET_L0.5103.300–
SMC_ROMBOOT1.40––
SMC_RX_L0.74––
SMC_S4_WAKESRC_EN0.744––
SMC_SENSOR_PWR_EN0.67––
SMC_TCK0.74––
SMC_TDI0.74––
SMC_TDO0.74––
SMC_TMS0.74––
SMC_TPAD_RST_L0.46––
SMC_TX_L0.74––
SMS_INT_L–3.400–
SPDIF_OUT_JACK0.687––
SPI_ALT_CLK0.58––
SPI_ALT_CS_L0.56––
SPI_ALT_MISO0.50––
SPI_ALT_MOSI0.51––
SPI_DESCRIPTOR_OVERRIDE_L0.745––
SPI_MLB_CLK0.5803.300–
SPI_MLB_CS_L0.563.300–
SPI_MLB_MISO0.503.300–
SPI_MLB_MOSI0.5103.300–
SPIROM_HOLD_L0.4903.200–
SPIROM_USE_MLB0.49––
SPIROM_WP_L0.643.300–
SPKR_SHUTDOWN0.533––
SPKRCONN_L_ID0.751––
SPKRCONN_R_ID0.73––
SPKRCONN_R_OUT_N0.50––
SPKRCONN_R_OUT_P0.50––
SPKRCONN_SR_OUT_N0.62––
SPKRCONN_SR_OUT_P0.62––
SSD_PWR_EN0.148––
SUS_PGOOD_CT0.63––
SYS_PWROK_R0.68––
SYSCLK_CLK25M_CAMERA0.45––
SYSCLK_CLK25M_TBT0.44––
SYSCLK_CLK25M_X10.45––
SYSCLK_CLK25M_X2_R0.45––
TBT_A_CIO_SEL0.796––
TBT_A_CONFIG1_BUF0.797––
TBT_A_CONFIG1_RC0.838––
TBT_A_D2R_C_N<1>0.777––
TBT_A_D2R_C_P<1>0.777––
TBT_A_D2R1_AUXDDC_N0.760––
TBT_A_D2R1_AUXDDC_P0.760––
TBT_A_DP_PWRDN0.795––
TBT_A_HPD0.818––
TBT_A_LSRX0.784––
TBT_A_LSTX0.773––
TBT_B_CIO_SEL0.801––
TBT_B_CONFIG1_BUF0.780––
TBT_B_CONFIG1_RC0.845––
TBT_B_D2R_C_N<1>0.773––
TBT_B_D2R_C_P<1>0.773––
TBT_B_D2R1_AUXDDC_N0.760––
TBT_B_D2R1_AUXDDC_P0.760––
TBT_B_DP_PWRDN0.803––
TBT_B_HPD0.845––
TBT_B_LSRX0.791––
TBT_B_LSTX0.767––
TBTBST_EN_UVLO0.615––
TBTDP_AUXIO_EN0.780––
TP_SUS_PGOOD_MR_L0.69––
UNCONNECTED_500.45––
UNCONNECTED_99OL––
USB_ILIM0.54––
USB_PWR_EN0.49––
VHP_FILTN0.907––
VREF_DAC0.740––
XDP_CPU_PWRBTN_L0.5653.400–
XDP_LPCPLUS_GPIO0.54––
XDP_USB_EXTA_OC_L0.49––
Z2_CLKIN0.73––
Z2_CS_L0.72––
Z2_HOST_INTN0.72––
Z2_KEY_ACT_L0.72––
Z2_MISO0.72––
Z2_MOSI0.72––
Z2_SCLK0.72––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3476?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3476: diode 0.161, voltage 12.500. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3476?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3476: diode 0.310, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3476?

OpenBoardData's known-good values for PP5V_S5 on the 820-3476: diode 0.479, voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3476 board?

Open your own 820-3476 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License