Apple laptop board · OpenBoardData

820-00239 known-good readings

Known-good readings for the Apple laptop board 820-00239: 1,355 nets, including 93 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 92 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00239.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 93 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 15

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V2_G3H_SMC_VDDC0.522––
AI: what PP1V2_G3H_SMC_VDDC is and how to check it

PP1V2_G3H_SMC_VDDC is the 1.2 V supply for the SMC's core (VDDC) in the always-on G3H domain — that reading comes from the rail name, not from board data. Known-good: diode 0.522 in diode mode, and about 1V2 at C5013 pin 1 once the 3V3 PP3V3_G3H rail is up (step 8 of the 5V-to-20V sequence). To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage at C5013 pin 1. A diode reading far from 0.522 suggests a short or leak on the rail; no voltage where 1V2 is expected points back to the upstream G3H rails or enable signals. These are community readings and a guide only, so confirm against a known-good board where possible.

PP3V0_G3H0.454––
AI: what PP3V0_G3H is and how to check it
  • What it is: PP3V0_G3H is a 3.0 V always-on rail; the G3H suffix (from the name) means it stays up whenever power is present, before the main power sequence.
  • Known-good reading: diode 0.454 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.454. Then apply power and measure the DC voltage; the name implies about 3.0 V, but that's from the name, not a recorded value.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream, to whatever generates or enables it. These are general guidelines, not confirmed for this board.
PP3V0_G3H_AVREF_SMC0.594––
AI: what PP3V0_G3H_AVREF_SMC is and how to check it

PP3V0_G3H_AVREF_SMC is a 3.0 V always-on rail (the G3H part of the name means always on), an SMC reference supply generated by U5165 and checked at C5166 pin 1. Its known-good reading here is diode 0.594 to ground; the archive has no known-good voltage value for it, so compare with a matching rail or a known-good board. With the board unpowered, measure diode mode from C5166 pin 1 to ground and compare with 0.594; then power up and check for about 3.0 V there. A diode reading far from 0.594 usually points to a short or a faulty part on that net, but one reading alone doesn't confirm a bad part.

PP3V3_G3H0.35––
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail from the G3H (always-on) startup stage, as the name indicates. The only known-good reading here is a diode value of 0.35 on PP3V3_G3H; no known-good voltage is listed for this rail.

  • With the board unpowered, measure diode mode from PP3V3_G3H to ground and compare with 0.35.
  • With power applied, check 3.3 V at L6900 pin 2 (PP3V3_G3H), and confirm 3.3 V EN at U6903 pin 10 (PM_EN_P3V3_G3H) first, since that enables the rail.

A diode reading far from 0.35 usually points to a short or a damaged component on the rail, but one reading isn't proof; a missing 3.3 V with EN present points more toward the regulator or its load. These community readings are a guide and vary with board state.

PP3V3_G3H_REG_R0.372––
AI: what PP3V3_G3H_REG_R is and how to check it
  • What it is: From the name, PP3V3_G3H_REG_R is a 3.3 V always-on (G3H) rail, a regulated derivative of PP3V3_G3H. The data doesn't list which parts sit on it.
  • Known-good: Diode reading to ground is 0.372 (community archive, a guide only). No known-good voltage reading here.
  • How to check: With the board unpowered, diode mode from the rail to ground and compare with 0.372. Then power up and measure the voltage; expect about 3.3 V, but that's general, not from this board's data.
  • If far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP3V3_G3H_SMC_VDDA0.363––
AI: what PP3V3_G3H_SMC_VDDA is and how to check it

PP3V3_G3H_SMC_VDDA — from the name, a 3.3 V always-on (G3H) analog supply (VDDA) for the SMC. It sits in the always-on startup stage, so it should be present as soon as the board has power.

  • Known-good here: diode mode to ground 0.363 (archive value, a guide only; it varies with board state). No known-good voltage reading for this net.
  • Check it unpowered in diode mode to ground, then with power applied measure the voltage — expect about 3.3 V from the name, but that's general, not a recorded value.
  • A diode reading far from 0.363 usually points to a short or a damaged part on the net; a missing voltage with a normal diode reading points upstream to the rail feeding it.
  • No known-good voltage here, so compare against a matching net or a known-good board of the same model.
PPBUS_G3H0.4450.435 LIFEBOAT%5fREMOVED13.100–
PPBUS_G3H_R0.460––
AI: what PPBUS_G3H_R is and how to check it
  • PPBUS_G3H_R is the main system bus rail; the G3H part means "always on" once the board is powered (from the name). It's generated late in the sequence by Q7030 and Q7040.
  • Known-good: diode 0.460 to ground. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, compare to 0.460. Then power up and measure the voltage; the sequence notes say PPBUS_G3H should reach about 20V once Q7030/Q7040 are driven.
  • A diode reading far from 0.460 usually points to a short or leaky part on the rail; a good diode but no voltage points back to the Q7030/Q7040 drive or the stages before them.
PPDCIN_G3H0.5420.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H (820-00239) — the "G3H" suffix, from the name, marks an always-on startup rail; PPDCIN is the DC input that feeds the early G3H stage.

  • Known-good readings in the archive: diode 0.54, voltage 20.000. No condition is recorded, and there is no known-good resistance value here.
  • Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the same point.
  • The notes also list it at Q3100, Q3200, QB300 and QB400 pin 8, so those are useful comparison points.
  • A diode reading far from 0.54 suggests a short or leaky part on the rail; a missing or low 20 V with a normal diode reading points upstream, toward the input path and the CD3215 stage.
PPDCIN_G3H_CHGR0.5420.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H part of the name marks it as an always-on startup rail (from the name). The archive lists a known-good diode reading of 0.54 and 20.000 V, with no condition noted, so treat both as a guide only.

  • With the board unpowered and the charger removed, measure diode mode from the rail to ground; a value far below 0.54 can suggest a short or a leaky part on the rail.
  • With power applied, measure the voltage; it should sit near 20 V when the charger is connected and the input path is working.
  • No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board if you need one.

A large deviation in either direction is a pointer to the input path, not a confirmed fault; check the upstream feed and the switching parts around the rail before replacing anything.

PPDCIN_G3H_CHGR_R0.570––
AI: what PPDCIN_G3H_CHGR_R is and how to check it
  • What it is: The name says it's a G3H (always-on) input rail feeding the charger section; the "_CHGR_R" suffix suggests a charger-side branch. Exact parts on the net aren't known here.
  • Known-good: diode reading 0.570 to ground is the only archived value; no known-good voltage is listed.
  • How to check: Power off and unplug, then diode mode from the rail to ground and compare with 0.570. Then apply power and measure the DC voltage on the rail.
  • If far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R0.44513.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — the name indicates a battery-voltage rail in the G3H (always-on) domain, fed from the charger side. It is not a switched rail, so it should be present whenever the charger is connected.

  • Known-good readings from the archive: diode 0.445 to ground, voltage 13.100. No condition is recorded with them, so treat them as a guide only.
  • To check: power off and unplug, then diode mode from the rail to ground and compare with 0.445. Then apply power and measure the voltage, comparing with 13.100.
  • A diode reading far below 0.445 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. Voltage well off 13.100 with a normal diode reading points upstream, toward the charger and battery-charging path.
  • No known-good resistance reading exists for this rail.
PPVBAT_G3H_CHGR_REG0.44513.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a battery-side rail; the G3H part of the name indicates it is always-on, and CHGR_REG suggests it is the charger's regulated battery feed. In the readings archive it shows a diode reading of 0.445 and 13.100 V, with no condition recorded, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.445 often points to a short or a leaky part on the rail; a voltage far from 13.100 V points to the charger or battery circuit not regulating. There is no known-good resistance reading for this rail here.

PPVBAT_G3H_CONN0.62––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is a battery-rail connection net; the G3H part of the name indicates it belongs to the always-on section of the power path (from the name, not from a board file). The only known-good reading here is a diode value of 0.62 to ground; no known-good voltage reading is recorded for this net.

  • With the board unpowered and the battery disconnected, measure diode mode from PPVBAT_G3H_CONN to ground and compare with 0.62.
  • Then apply power and measure the voltage on the net, comparing against a matching net on the other side of the battery connector pair or a known-good board, since no voltage value is listed.

A diode reading far below 0.62 usually suggests a short or a leaky part on the rail; far above it can mean an open connection. Treat these as a guide, not a confirmed fault, and check the connector and its joints before replacing anything.

PPVIN_G3H_P3V3G3HOL––
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H — 820-00239 reference note

  • What it is: from the name, a 3.3 V always-on (G3H) rail that feeds the G3H power input. The sequence notes list it as 3V3 at D6902 pin 3, reached after the CD3215 LDOs and the gate voltages come up.
  • Known-good: 3V3 at D6902 pin 3 (community reading, a guide only). The archive shows no known-good diode-mode value for this net — the OL logged here is the only entry, so treat it as unconfirmed rather than as a good reference.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with a matching always-on 3V3 rail or a known-good board. Then power up and measure the voltage at D6902 pin 3.
  • If it's far off: a missing 3V3 here usually points back to the upstream steps — the CD3215 LDOs, the gate voltages, or the enable at U6903 pin 10 — rather than to this rail itself. Confirm those before suspecting a part on this net.

S5 and SUS: standby 17

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_SUS_PCH_VCCCLK2_F0.1351.000–
AI: what PP1V_SUS_PCH_VCCCLK2_F is and how to check it

PP1V_SUS_PCH_VCCCLK2_F — from the name, a 1 V standby (SUS) rail feeding the PCH clock section. It sits at the S5/standby stage, so it should be present before the board fully powers on.

  • Known-good readings in the archive: diode 0.135 to ground, voltage 1.000 V. These are community values and only a guide.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail (or its test point). Then apply power and measure the voltage.
  • No known-good resistance reading here; compare against a matching net or a known-good board.
  • A voltage far off 1.000 V, or a diode reading well below 0.135, usually points to a short or a missing enable/supply on that rail. Confirm with a second measurement before replacing anything.
PP1V_SUS_PCH_VCCCLK4_F0.1351.000–
AI: what PP1V_SUS_PCH_VCCCLK4_F is and how to check it

PP1V_SUS_PCH_VCCCLK4_F — from the name, a 1 V standby (SUS) rail feeding the PCH clock domain (VCCCLK4). It sits in the S5/standby startup stage, so it should be present before the board fully powers on.

  • Known-good readings here: diode 0.135 to ground, voltage 1.000 V. These are community readings and only a guide, with no condition recorded.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.135. Then apply power and measure the voltage at the rail.
  • A diode reading far below known-good usually points to a short or a leaking part on the rail; a correct diode but no voltage points upstream, to the rail's enable or supply. No known-good resistance reading exists here, so compare against a matching net or a known-good board.
PP1V_SUS_PCH_VCCCLK5_F0.1351.000–
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it

PP1V_SUS_PCH_VCCCLK5_F — from the name, a 1 V standby (SUS) rail feeding the PCH clock section (VCCCLK5). The "S5/SUS" part of the name places it in the standby stage, so it should be present before the board fully powers on.

  • Known-good readings in the archive: diode 0.135 and voltage 1.000 V. No condition is recorded, so treat these as a guide only.
  • Check it with the board unpowered: diode mode, red probe on ground, black on the rail (or the cap/test point on it) and compare with 0.135. Then apply power and measure the voltage; expect about 1.000 V.
  • A diode reading far below 0.135 suggests a short or a leaky part on the rail; far above suggests an open path. A missing or wrong voltage points to the rail's source or its enable, not necessarily the load.
  • No known-good resistance reading exists for this rail, so compare against a matching net or a known-good board if you need one.
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.1351.000–
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL_F is and how to check it
  • What it is: From the name, PP1V_SUSSW_PCH_VCCAMPHYPLL_F is a 1 V rail feeding the PCH's VCCAMPHYPLL supply, in the S5/SUS standby domain. That reading is from the name only; the parts on the net aren't known here.
  • Known-good readings: diode 0.135 and voltage 1.000, with no condition recorded. These are community readings and only a guide.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a low diode reading or a missing 1 V usually points to a short or a rail that isn't being enabled, but one reading doesn't confirm a bad part. No known-good resistance reading here; compare against a matching net or a known-good board.
PP1V0_SUS0.1351.000–
AI: what PP1V0_SUS is and how to check it

PP1V0_SUS is a 1.0 V standby rail; the "SUS" and S5 stage come from the rail name, and it's present in standby before full power-on. The archive lists a known-good diode reading of 0.135 to ground and 1.000 V with power applied; treat these as a guide only, since community readings vary with board state.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.135.
  • Then power the board and measure the voltage, expecting about 1.000 V.
  • A diode reading far below 0.135 suggests a short or leaky load on the rail; far above it suggests an open path. Confirm with a second measurement before suspecting a part.
  • No known-good resistance value is listed for this rail.
PP1V0_SUSSW0.1351.000–
AI: what PP1V0_SUSSW is and how to check it

PP1V0_SUSSW — the name indicates a 1.0 V standby rail (SUS/S5), from the name only; the archive doesn't list which parts sit on it.

  • Known-good from the archive: diode 0.135 to ground (board unpowered) and 1.000 V with power applied. No condition is recorded, and there's no known-good resistance reading here.
  • Check it in diode mode to ground with the board off, then measure the voltage with power applied.
  • A diode reading far below 0.135 suggests a short or leaky load on the rail; a voltage well off 1.000 V points to the rail not coming up or being loaded down. Treat these as guides, not proof of a bad part.
PP1V8_SUS0.317––
AI: what PP1V8_SUS is and how to check it

PP1V8_SUS is a 1.8 V standby rail; the "SUS" and S5 tags come from the name and place it in the standby stage. The only known-good figure here is a diode reading of 0.317 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power up and measure the voltage. A diode reading far from 0.317 can point to a short or a damaged part on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V8_SUS_REG_R0.3101.800–
AI: what PP1V8_SUS_REG_R is and how to check it

PP1V8_SUS_REG_R is a 1.8 V standby rail; the "SUS" and "S5" in its name indicate it belongs to the always-on standby stage, though that's from the name, not from board data. The archive gives a known-good diode reading of 0.310 and a voltage of 1.800 for this net, with no condition noted.

  • With the board unpowered, measure diode mode from PP1V8_SUS_REG_R to ground; around 0.310 is the guide.
  • Then apply power and measure the rail itself; it should sit near 1.800 V.
  • No known-good resistance reading here, so compare against a matching rail or a known-good board if needed.

A diode reading far below 0.310 usually suggests a short or a leaky part on the rail, while a missing or low voltage with a normal diode reading points more to the regulator or its enable. These are likely causes, not confirmed ones, so check the enable and supply side of the regulator before replacing anything.

PP3V3_S50.3700.355 LIFEBOAT%5fREMOVED3.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the S5/SUS part of the name places it in the standby stage (from the name, not a schematic).

  • Known-good readings here: diode 0.370 to ground, and 0.355 in the LIFEBOAT_REMOVED condition; voltage 3.300.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A diode reading well below known-good usually points to a short or a leaky part on the rail; a missing 3.3 V with a normal diode reading points more to the rail not being enabled or its source not running.
  • No known-good resistance reading here, so compare against a matching rail or a known-good board.
PP3V3_S5_SSD0.34––
AI: what PP3V3_S5_SSD is and how to check it

PP3V3_S5_SSD is a 3.3 V standby rail feeding the SSD, judging by its name (S5/SUS = standby stage). The only known-good figure here is a diode reading of 0.34 to ground; there is no known-good voltage or resistance value recorded for this rail.

  • With the board unpowered, measure diode mode from PP3V3_S5_SSD to ground and compare with 0.34; a much lower reading suggests a short or leaky part on the rail, a much higher one an open path.
  • Then apply power and check the rail sits near 3.3 V, since standby rails should be up before the main supplies.
  • A voltage far off 3.3 V usually points to the standby regulator or its enable, not the SSD itself. These are community readings and only a guide, so confirm against a known-good board where possible.
PP3V3_S5_SSD_LB0.3720.443 LIFEBOAT%5fREMOVED––
AI: what PP3V3_S5_SSD_LB is and how to check it

PP3V3_S5_SSD_LB — from the name, a 3.3 V standby rail (S5/SUS) feeding the SSD; the exact loads aren't known from the readings archive.

  • Known-good diode readings to ground: 0.372, and 0.443 with the condition noted as LIFEBOAT_REMOVED. These are community readings and only a guide.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail (or the test point/pad carrying it). Then power up and measure the DC voltage on the same point.
  • No known-good voltage reading is recorded here for this rail, so compare against a matching rail on a known-good board rather than a fixed number.
  • A diode reading far below known-good often suggests a shorted load or capacitor on the rail; a much higher one can mean an open trace or missing part. Neither confirms a bad part on its own — recheck and compare before replacing anything.
PP3V3_S5_T1390.376––
AI: what PP3V3_S5_T139 is and how to check it
  • PP3V3_S5_T139 is a 3.3 V standby rail; the "S5" and "SUS" naming marks it as a standby-stage rail (from the name, general convention).
  • Known-good from the archive: diode 0.376 to ground. No known-good voltage reading is recorded here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.376 suggests a short or a leaky part on the rail; confirm with a second measurement before replacing anything.
PP3V3_S5_TBT_T_SW0.482––
AI: what PP3V3_S5_TBT_T_SW is and how to check it
  • What it is: PP3V3_S5_TBT_T_SW is a 3.3 V rail in the S5 standby domain, judging by its name (S5 = standby, TBT = Thunderbolt, SW = switched). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.482 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Power up and measure the rail voltage; compare against a matching Thunderbolt rail on the other side of the pair, since no voltage value is listed.
  • If far off: a diode reading well below 0.482 suggests a short or leaky part on the rail; well above suggests an open path. Confirm with voltage and resistance before replacing anything.
PP3V3_S5_TBT_X_SW0.48––
AI: what PP3V3_S5_TBT_X_SW is and how to check it

PP3V3_S5_TBT_X_SW is a 3.3 V standby rail for the Thunderbolt (TBT) section, judged from its name; the S5/SUS part puts it in the standby stage. The only known-good reading here is a diode value of 0.48 to ground; there is no known-good voltage reading for this rail in the data. With the board unpowered, measure diode mode from the rail to ground and compare with 0.48. Then power the board and check the voltage at the rail, comparing against a matching TBT rail on the other side of the pair or a known-good board. A diode reading far below 0.48 suggests a short or a failing part on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_SUS0.352––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS (820-00239) — From the name, this is the 3.3 V standby rail (SUS = suspend/standby), present in the S5 standby stage before the board fully powers on.

  • Known-good from the readings archive: diode 0.352 to ground. No known-good voltage reading is recorded here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the DC voltage on the same point.
  • A diode reading far from 0.352 usually points to a short or a leaky load on the rail, but one reading isn't proof — compare with a matching net or a known-good board before replacing anything.
PP5V_S50.45––
AI: what PP5V_S5 is and how to check it
  • PP5V_S5 is a 5 V rail; the "S5" in its name marks it as a standby-stage rail (from the name).
  • Known-good: diode reading 0.45 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.45 usually points to a short or a leaky part on that rail, but one reading isn't proof; compare with a known-good board before replacing anything.
PPVCCPRIMCORE_SUS_PCH0.1101.000–
AI: what PPVCCPRIMCORE_SUS_PCH is and how to check it

PPVCCPRIMCORE_SUS_PCH — the name indicates the primary core supply for the PCH in its suspend (SUS) state, so it belongs to the S5/standby stage rather than a full-on rail. Known-good readings in the archive: diode 0.110 and voltage 1.000 V. No known-good resistance value is recorded here.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.110; a much lower reading suggests a short or leaky load on the rail.
  • Then apply power and check the voltage against 1.000 V, ideally at the same standby state the reading was taken in.
  • A reading far from known-good points at the rail's supply or its load, but one reading alone doesn't confirm a bad part — verify at a second point on the same net before replacing anything.

S4 18

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V8_S40.430––
AI: what PP1V8_S4 is and how to check it
  • What it is: PP1V8_S4 is a 1.8 V rail that comes up at the S4 stage of startup, judging from its name. The board data doesn't say which parts it feeds.
  • Known-good reading: diode 0.430 to ground, from the community readings archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a low diode reading usually points to a short or a leaky load on the rail, but one reading doesn't confirm a bad part. Compare with a matching rail or a known-good board before replacing anything.
PP3V3_S40.370––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail that comes up at the S4 stage of the power sequence, judging by its name; the archive has no description of what it feeds. The only known-good figure recorded is a diode reading of 0.370 to ground, with no condition noted, and there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.370 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S4_BT0.370––
AI: what PP3V3_S4_BT is and how to check it

PP3V3_S4_BT is a 3.3 V rail that, judging by the name, comes up at the S4 stage of the power sequence (the "BT" suffix likely marks a Bluetooth-related branch, but that's from the name only, not confirmed here). The only known-good figure in the archive is a diode reading of 0.370 to ground; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from PP3V3_S4_BT to ground and compare with 0.370 — treat it as a guide, since readings vary with board state.
  • Then apply power and check the voltage on the rail; no known-good voltage is recorded here, so compare against a matching S4 rail or a known-good board.
  • A diode reading far below 0.370 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. Confirm with a second measurement before replacing anything.
PP3V3_S4_MESA0.369––
AI: what PP3V3_S4_MESA is and how to check it
  • PP3V3_S4_MESA is a 3.3 V rail; the "S4" in the name marks it as a startup-stage rail (from the name). "MESA" is likely a load/domain label, but that's general inference, not from the board data.
  • Known-good: diode reading 0.369 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail.
  • A diode reading far from 0.369 usually points to a short or a leaky part on that rail; confirm with a second reading before replacing anything.
PP3V3_S4_MESA_SW0.369––
AI: what PP3V3_S4_MESA_SW is and how to check it
  • What it is: PP3V3_S4_MESA_SW is a 3.3 V rail that switches on at the S4 stage of startup, both from the name. "MESA" is likely a load or domain label; the exact parts on it aren't known here.
  • Known-good reading: diode 0.369 to ground, from the community archive and a guide only. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure the voltage.
  • If it's far off: a low diode reading or missing voltage usually points to a shorted load or a rail that isn't being enabled — not proof of a bad part. Next, check the enable and the supply feeding it.
PP3V3_S4_SOC_PMU0.364––
AI: what PP3V3_S4_SOC_PMU is and how to check it
  • What it is: PP3V3_S4_SOC_PMU is a 3.3 V rail for the SoC's PMU, enabled at the S4 stage of power-up (both from the name). On this board the archive only records its diode reading, so there is no known-good voltage or resistance here.
  • Diode check: with the board unpowered, measure in diode mode from the rail to ground. The archived guide is 0.364; a much lower reading (near zero) suggests a short on the rail, while a clearly higher one can mean an open or missing connection.
  • Voltage check: power the board and measure the rail; it should come up when the board reaches S4. No known-good voltage is listed, so compare against a matching rail or a known-good board.
  • A single reading off the guide isn't proof of a bad part; check the rail's enable and upstream supply before replacing anything.
PP3V3_S4_TPAD0.33––
AI: what PP3V3_S4_TPAD is and how to check it

PP3V3_S4_TPAD is a 3.3 V rail that comes up at the S4 stage of the power sequence — that's from the rail's name, not from a schematic. The only known-good reading here is a diode value of 0.33, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; the archive has no known-good voltage for this rail, so compare against a matching rail or a known-good board. A diode reading far below 0.33 usually points to a short or a leaky part on the rail, but one reading isn't proof — lift or isolate parts before replacing anything.

PP3V3_S4_WLAN_SW0.340––
AI: what PP3V3_S4_WLAN_SW is and how to check it
  • What it is: PP3V3_S4_WLAN_SW is a 3.3 V rail for the WLAN section, enabled at the S4 stage — that reading comes from the name, not from board data.
  • Known-good reading: diode 0.340 to ground, from the community archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.340. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. A single reading isn't proof — confirm with the voltage check before replacing anything.
PP3V3_S4_WLAN_SW_R0.340––
AI: what PP3V3_S4_WLAN_SW_R is and how to check it

PP3V3_S4_WLAN_SW_R is a 3.3 V switched WLAN rail; the "S4" in its name places it in the S4 power stage, and "_SW" suggests it is gated on rather than always present (from the name only). The only known-good figure here is a diode reading of 0.340 to ground; there is no known-good voltage reading for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.340; a much lower reading suggests a short on the rail, a much higher one an open path.
  • Then power the board and check the voltage, but no known-good voltage is recorded here, so compare against a matching rail on a known-good board.
  • A rail far off known-good usually points to a shorted load or a missing enable, not confirmed until traced.
PP3V3_S4SW_SNSOL––
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail that switches on at the S4 stage of startup, judging by its name (the data doesn't describe its function beyond that). The only reading recorded here is a diode value of OL to ground, with no condition given, so treat it as a guide; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from the rail to ground and compare with the recorded OL.
  • Then apply power and measure the rail voltage, comparing against a known-good board of the same model if one is available.

A diode reading far below the recorded OL usually points to a short or a leaky part on that rail, but a single reading doesn't confirm a fault.

PP5V_S40.1200.422 LIFEBOAT%5fREMOVED5.000–
AI: what PP5V_S4 is and how to check it

PP5V_S4 — 820-00239 reference note

  • What it is: a 5 V rail in the S4 startup stage; the "S4" part comes from the rail name, and S4 is a later power state than the always-on G3H rails.
  • Known-good readings (community archive, guide only): diode 0.120 in circuit; diode 0.422 with the condition noted as LIFEBOAT_REMOVED; voltage 5.000.
  • How to check: with the board unpowered, diode mode from PP5V_S4 to ground and compare with 0.120 (or 0.422 with the lifeboat removed). Then apply power and confirm about 5.000 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; no voltage with a normal diode reading points upstream to the rail's enable or source. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.
PP5V_S4_P2V7NAND_LB0.4230.466 LIFEBOAT%5fREMOVED––
AI: what PP5V_S4_P2V7NAND_LB is and how to check it

PP5V_S4_P2V7NAND_LB — from the name, a 5 V rail in the S4 power stage, tied to the NAND supply (the "P2V7" part suggests a 2.7 V-related NAND rail). The archive lists two diode readings to ground: 0.423, and 0.466 with the condition LIFEBOAT_REMOVED. No voltage reading is recorded here.

  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with those two figures.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is recorded here, so compare against a matching rail on a known-good board.
  • A diode reading far below the known-good range usually points to a short or leaky part on that rail; a small difference can be normal, so don't condemn a part on one reading.
PP5V_S4_T_USBC0.1955.000–
AI: what PP5V_S4_T_USBC is and how to check it

PP5V_S4_T_USBC — the name indicates a 5V rail in the S4 startup stage, tied to the USB-C side (general reading of the name, not from board data).

  • Known-good readings in the archive: diode 0.195 to ground, voltage 5.000 V. No condition is recorded with them, so treat them as a guide only.
  • Check it with the board unpowered and discharged: meter in diode mode, black probe on ground, red on the rail. Then apply power and measure the voltage.
  • A diode reading far from 0.195 usually points to a short or a leaky part on that rail; a voltage well off 5.000 V with a normal diode reading points upstream, at whatever generates the rail.
  • No known-good resistance reading exists for this rail, so compare against a matching net on the other USB-C side if one is available.
PP5V_S4_TPAD_CONN0.41––
AI: what PP5V_S4_TPAD_CONN is and how to check it

PP5V_S4_TPAD_CONN is a 5 V rail feeding the trackpad connector, and the S4 in its name (from the name) puts it in the S4 startup stage, so it should come up later in the power sequence rather than at initial power-on.

  • Known-good from the readings archive: diode 0.41 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe to ground, black to the rail; then power the board and measure the voltage at the rail.
  • A diode reading far from 0.41 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a known-good board or matching net before replacing anything.
PP5V_S4_WLAN_ISNS_DOL––
AI: what PP5V_S4_WLAN_ISNS_D is and how to check it
  • PP5V_S4_WLAN_ISNS_D is, from its name, a 5 V rail feeding the WLAN section at the S4 stage, with the "ISNS" suffix suggesting a current-sense node rather than a plain supply. The name is the only description available here.
  • Known-good readings: diode mode to ground is listed as OL. No known-good voltage or resistance reading for this net is recorded here.
  • To check it: power off and unplug, then diode mode from the net to ground and compare with the OL figure. Then apply power and measure the DC voltage, comparing against a matching 5 V S4 rail or a known-good board, since no voltage value is listed.
  • A diode reading far from OL (a low reading) usually points to a short or a leaky part on that net; an open reading with no voltage present points more to a missing enable or upstream supply. Treat the OL figure as a community guide, not a guarantee.
PP5V_S4_X_USBC0.2105.000–
AI: what PP5V_S4_X_USBC is and how to check it

PP5V_S4_X_USBC — the name indicates a 5 V rail for the USB-C side of the X (secondary) CD3215 path, in the S4 power state (from the name; the archive has no part list for this net).

  • Known-good from the archive: diode 0.210 to ground, voltage 5.000 V. Treat these as a community guide, not a spec.
  • Check with the board unpowered and discharged: diode mode, red probe on ground, black on the rail. Then apply power and measure DC volts on the same net.
  • A diode reading well below 0.210 suggests a short or leaky load on the rail; a missing 5 V with a normal diode reading points upstream, toward the CD3215 unit and its LDOs and gate signals.
  • No known-good resistance reading is recorded for this rail.
PPBUS_S4_HS_TPAD0.445––
AI: what PPBUS_S4_HS_TPAD is and how to check it

PPBUS_S4_HS_TPAD — reference note

  • This is a PPBUS rail that switches in at the S4 stage, judging from the name (PPBUS = main bus after the charger/PPBUS_G3H stage; S4 = a later sleep/power state; TPAD = trackpad). The exact parts on it aren't documented here.
  • Known-good: diode reading to ground 0.445 (community archive, board state not stated). No known-good voltage or resistance reading here.
  • Check with the board unpowered and discharged: multimeter in diode mode, black probe on ground, red on the rail, and compare with 0.445. Then power up and measure the DC voltage at the rail.
  • A diode reading far below 0.445 suggests a short or leaky part on the rail; far above suggests an open path. One reading isn't proof a part is bad — confirm with a voltage check and compare against a matching rail on the other side.
PPVIN_S4_TPAD_FUSE0.445––
AI: what PPVIN_S4_TPAD_FUSE is and how to check it
  • What it is: From the name, a fused input rail feeding the trackpad section at the S4 startup stage. The data doesn't list which parts sit on it.
  • Known-good: diode reading to ground of 0.445 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from the net to ground. Then power up and measure the voltage on the fuse's far side.
  • If far off: a much lower diode reading usually points to a short on that rail; a much higher one to an open fuse or feed. Confirm with a second measurement before replacing anything.

S3: memory 9

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.692––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it
  • What it is: PP0V6_S3_MEM_VREFCA_A is a 0.6 V memory reference rail; the S3 stage and memory role come from the name, not from a schematic here.
  • Known-good reading: diode 0.692 to ground (community value, a guide only, board state unknown). No known-good voltage or resistance reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power on and measure the DC voltage, which should sit near 0.6 V by the name.
  • If it's far off: a low diode reading or a dragged-down voltage usually points to a short or a load on the rail, but that isn't confirmed. Compare with a matching memory reference rail on a known-good board before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.748––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it
  • What it is: PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail. The "0V6" and "S3" in the name indicate a 0.6 V rail in the S3 (memory) startup stage; that reading is from the name, not from a schematic.
  • Known-good reading: diode 0.748 to ground (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.748. Then power up and measure the DC voltage, which should sit near 0.6 V by the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode but missing voltage points upstream to the rail's enable or source. No known-good voltage or resistance value is available for this rail, so compare against a matching memory rail on a known-good board before replacing anything.
PP0V6_S3_MEM_VREFDQ_B0.748––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail; the "S3" and "MEM" parts come from the name, and it is a DDR reference for the data (DQ) lines rather than a main power rail. The only known-good figure here is a diode reading of 0.748 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. No known-good voltage reading is recorded here, so compare against a matching memory reference net or a known-good board. A diode reading far below 0.748 usually points to a short or leaky part on the rail, but one reading is not proof, so confirm before replacing anything.

PP1V0_S30.225––
AI: what PP1V0_S3 is and how to check it
  • PP1V0_S3 is a 1.0 V rail; the S3 suffix places it in the memory stage of startup, from the name. The name doesn't say which parts it feeds.
  • Known-good: diode 0.225 to ground. No known-good voltage reading is recorded for this rail.
  • Check it with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.225. Then power up and measure the DC voltage at the rail.
  • A diode reading far below 0.225 suggests a short or a leaky part on the rail; far above suggests an open path. A single reading isn't proof, so confirm with a second point on the same net or a known-good board before replacing anything.
PP1V2_S30.241.200–
AI: what PP1V2_S3 is and how to check it

Reference note for PP1V2_S3 on the 820-00239:

  • What it is: the "1V2" in the name indicates a 1.2 V rail, and "S3" places it in the memory stage of the startup sequence (this is from the name, not from board data).
  • Known-good readings (community archive, a guide only): diode 0.24 to ground, and 1.200 V with power applied. No known-good resistance reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a low diode reading or a missing/incorrect voltage usually points to a short or a rail that isn't being enabled. No confirmed cause is known here, so trace the enable and source before replacing anything.
PP1V2_S3_CPUDDR0.261––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is a 1.2 V memory rail; the "S3" and "CPUDDR" in its name indicate it belongs to the memory (DDR) supply that comes up in the S3 state. From the readings archive, its known-good diode reading to ground is 0.261, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and confirm about 1.2 V is present. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.261 usually points to a short or a faulty component on that rail, but one reading alone doesn't confirm a bad part.

PP1V2_S3_REG_R0.2551.200250.000
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R — the name indicates a 1.2 V regulator rail in the S3 (memory) startup stage; that reading is from the name, not from a schematic.

  • Known-good readings here: diode 0.255, voltage 1.200, resistance 250.000. These are community figures and only a guide.
  • Check with the board unpowered (battery and charger off): diode mode from the rail to ground, then resistance to ground. Power up and measure the voltage.
  • A voltage well off 1.200 V, or a diode/resistance far from 0.255/250, usually points to a short or a rail not being enabled — not proof of a bad part on one reading.
  • No known-good values of other kinds are listed for this rail.
PP1V8_S30.3741.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the "S3" suffix comes from its name and marks it as a memory (S3) stage rail on this board. Known-good readings here: diode 0.374 and voltage 1.800.

  • With the board unpowered, measure diode mode from the rail to ground; a value near 0.374 is the guide.
  • With power applied, measure the rail voltage; it should sit at about 1.800 V.
  • A diode reading far below 0.374 suggests a short or a leaky load on the rail; a voltage well off 1.800 V points to the rail not being enabled or its source failing.

No known-good resistance reading is recorded for this rail, so compare against a matching rail or a known-good board. These are community readings and vary with board state, so treat them as a guide, not a pass/fail limit.

PP1V8_S3_MEM0.3751.800–
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM is a 1.8 V memory rail; the S3 in its name (from the name) marks it as a memory-stage rail in the startup sequence. Known-good readings for this board: diode 0.375 and voltage 1.800, with no condition recorded, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well off 1.800 or a diode reading far from 0.375 points to a problem on that rail or its supply, but one reading alone doesn't confirm a bad part; there is no known-good resistance value here.

S0: running 34

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.091––
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the "S0" in the name marks it as a running-state rail, and the "DDRVTT" part is the termination voltage for the memory bus. The only known-good reading here is a diode value of 0.091 to ground; there is no known-good voltage or resistance reading for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.091. A much lower reading suggests a short or a leaky part on the rail; a much higher one can mean an open trace or missing part.
  • Then power the board into S0 and measure the voltage; expect roughly 0.6 V, but that figure comes from the rail name, not from measured data.
  • If the diode reading is far off, the usual suspects are a shorted decoupling capacitor or a failed termination regulator, but that is general guidance, not confirmed for this board.
PP1V0_S0SW0.223––
AI: what PP1V0_S0SW is and how to check it

PP1V0_S0SW is a 1.0 V supply rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "SW" suggests a switched rail. The only known-good reading here is a diode value of 0.223 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.223 usually points to a short or a leaky part on the rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V2_S0SW0.262––
AI: what PP1V2_S0SW is and how to check it
  • PP1V2_S0SW is a 1.2 V rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "SW" suggests a switched rail. This is from the name only.
  • Known-good reading in the archive: diode 0.262 to ground. No known-good voltage is listed for this rail.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.262 usually points to a short or a leaky part on the rail, but one reading isn't proof; compare with a matching rail or a known-good board before replacing anything.
PP1V8_S00.360––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail that, judging by the S0 suffix in its name, is a running-state supply (general naming convention, not from this board's data). The only known-good figure recorded here is a diode reading of 0.360 to ground; no known-good voltage reading is listed.

  • With the board unpowered, measure diode mode from PP1V8_S0 to ground and compare with 0.360.
  • Then power the board and measure the voltage on the rail; expect roughly 1.8 V if it is up, but no known-good voltage is recorded here to compare against.

A diode reading far below 0.360 usually suggests a short or a leaky load on the rail; far above it can mean an open path. A single off reading isn't proof of a bad part, so confirm with a second measurement before replacing anything.

PP1V8_S0_PCH_VCCHDA_F0.355––
AI: what PP1V8_S0_PCH_VCCHDA_F is and how to check it
  • What it is: A 1.8 V rail for the PCH's HDA (audio) supply, from the name; the S0 suffix means it belongs to the running state, so it should only be up once the board is fully on.
  • Known-good reading: diode 0.355 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off, discharge, then diode mode from the rail to ground and compare with 0.355. Then power on and measure the voltage; expect about 1.8 V once the board is in S0.
  • If it's far off: a much lower diode reading suggests a shorted load on the rail; a correct diode reading with no voltage points to the rail's enable or supply, not the rail itself. These are guides, not confirmed faults.
PP1V8_S0SW_DFR0.500––
AI: what PP1V8_S0SW_DFR is and how to check it
  • What it is: PP1V8_S0SW_DFR is a 1.8 V rail; the "S0" in the name marks it as a running-state (S0) supply, and "SW" suggests a switched rail (from the name only).
  • Known-good reading: diode 0.500 to ground, from the readings archive. No known-good voltage is listed for this rail.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.500; then power the board and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail, but one reading isn't proof — confirm before replacing anything.
PP3V3_S00.330––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is a 3.3 V rail that, judging by the S0 suffix in its name, is a run-state supply (general naming convention, not from this board's data). The only known-good figure recorded here is a diode reading of 0.330 to ground; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from PP3V3_S0 to ground and compare with 0.330; a much lower reading suggests a short or leaky load on the rail.
  • Then power the board and measure the rail voltage, expecting about 3.3 V once the board is in its running state.
  • A far-off diode reading or a missing voltage points to a shorted load or a rail that never comes up, but one reading alone doesn't confirm a bad part.
PP3V3_S0_CPUTHMSNS_TI_R0.320––
AI: what PP3V3_S0_CPUTHMSNS_TI_R is and how to check it
  • What it is: a 3.3 V S0 (running-state) rail, judging by the name: PP3V3 = 3.3 V, S0 = running stage, and CPUTHMSNS suggests a CPU thermal-sense feed. The exact parts on it aren't known here.
  • Known-good: diode-to-ground 0.320 in the archive. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure its voltage.
  • If far off: a low diode reading usually points to a shorted load on the rail, a high one to an open feed. Confirm with a second reading before replacing anything.
PP3V3_S0SW_DFR0.530––
AI: what PP3V3_S0SW_DFR is and how to check it

PP3V3_S0SW_DFR is a 3.3 V rail that is switched on in the S0 (running) state, judging from its name; the "DFR" suffix suggests it feeds a display-related circuit, but that is inference from the name only.

  • Known-good reading in the archive: diode mode to ground 0.530. No known-good voltage reading is recorded here.
  • Check it unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.530.
  • Then power the board and measure the voltage; the archive gives no expected value, so compare against a matching rail on a known-good board.
  • A diode reading far below 0.530 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection. One reading alone doesn't confirm a bad part.
PP3V3_S0SW_LCD0.56––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is a switched 3.3 V LCD rail; the "S0" in the name indicates it belongs to the running (S0) state, and "SW" suggests it is switched on by a control signal rather than always present. The only known-good figure in the readings archive is a diode reading of 0.56 to ground, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail, ideally with the display connected and the board in S0. A diode reading far below 0.56 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path; a missing voltage with a normal diode reading points more to the switch or its enable signal. Treat the 0.56 as a community guide only, and compare against a matching rail or a known-good board before condemning anything.

PP3V3_S0SW_LCD_R0.572––
AI: what PP3V3_S0SW_LCD_R is and how to check it
  • What it is: PP3V3_S0SW_LCD_R is a switched 3.3 V LCD rail. From the name, it's a 3.3 V rail (PP3V3), switched on in the S0 running state (S0SW), feeding the display (LCD). The "_R" suffix is likely a right-side variant, but that's inference from the name, not from the board data.
  • Known-good reading: diode 0.572 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.572. Then power on and measure the voltage; it should come up only once the board is in S0.
  • If far off: a much lower diode reading suggests a short on the rail; no voltage in S0 points to the switch or its enable, not necessarily the LCD. These are guides from community readings, not confirmed values.
PP3V3_TBT_T_S00.3093.300–
AI: what PP3V3_TBT_T_S0 is and how to check it

PP3V3_TBT_T_S0 is a 3.3 V rail; the name suggests it supplies the Thunderbolt section and, by the S0 suffix, is active in the running state (from the name, not from board data).

  • Known-good readings here: diode 0.309 to ground, voltage 3.300. These are community values and only a guide, since they vary with board state.
  • Check it with the board unpowered in diode mode, red probe on the rail and black on ground, then power up and measure the voltage.
  • No known-good resistance reading is listed for this rail.
  • A diode value far below 0.309 usually points to a short or a leaky part on the rail; a missing 3.3 V with a normal diode reading points upstream to the rail's supply or enable.
PP3V3_TBT_X_S00.310––
AI: what PP3V3_TBT_X_S0 is and how to check it
  • What it is: PP3V3_TBT_X_S0 is a 3.3 V rail for the Thunderbolt section, from the name; the S0 suffix means it belongs to the running (S0) state.
  • Known-good reading: diode 0.310 to ground, from the readings archive. No known-good voltage is listed here.
  • How to check: power off and unplug, then diode-mode from the rail to ground and compare with 0.310. Then power on and measure the voltage; it should sit near 3.3 V once the board is in S0.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail, while a missing voltage with a normal diode reading points upstream to its enable or supply. These are general guidelines, not confirmed causes for this board.
PP5V_S00.45––
AI: what PP5V_S0 is and how to check it

PP5V_S0 — from the name, a 5 V rail that comes up in the S0 (running) state. The archive lists one known-good reading: diode 0.45 (no condition given), and no known-good voltage here.

  • With the board unpowered, diode mode from PP5V_S0 to ground; compare with 0.45. A short or very low reading points to a load on the rail, not the rail itself.
  • Then apply power and measure the voltage in S0. No known-good voltage is recorded here, so compare against a matching rail or a known-good board.
  • A far-off diode reading or missing 5 V usually means the rail isn't being enabled or has a shorted load; confirm the enable and the source before replacing anything.
PP5V_S0_ALSCAM_F0.45––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "ALSCAM" suggests it feeds the camera circuit — that part is from the name, not confirmed circuit data. The only known-good reading recorded here is a diode value of 0.45 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.45 usually points to a short or a damaged component on that rail, but a single reading isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP5V_S0_BKLT_A0.4615.130–
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the 5 V backlight rail that runs in the S0 (running) state, judged from its name; it is not a standby rail. From the readings archive, the known-good guide values are diode 0.461 and voltage 5.130, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading well below 0.461 suggests a short or leaky load on the rail; a voltage far from 5.130 with the board in S0 points to the rail not being enabled or its source failing. No known-good resistance reading exists here, so compare against a matching net or a known-good board.

PP5V_S0_BKLT_D0.4625.000–
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D — the name suggests a 5 V backlight rail that comes up in the S0 (running) state; that reading is from the name, not from board data.

  • Known-good readings for this net: diode 0.462 to ground, and 5.000 V with the board powered in S0.
  • To check it: power off, measure diode mode from the net to ground, then apply power and measure the voltage in S0.
  • A diode reading well below 0.462 suggests a short or leaky load on the rail; a voltage far from 5.000 V points to the rail not being enabled or its source failing.
  • No known-good resistance reading exists here, so compare against a matching net or a known-good board.
PP5V_S0_FAN_CONN0.45––
AI: what PP5V_S0_FAN_CONN is and how to check it
  • What it is: From the name, PP5V_S0_FAN_CONN is a 5 V rail feeding the fan connector, enabled in the S0 (running) state.
  • Known-good reading: diode 0.45 to ground, from the readings archive; no known-good voltage value here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power on and measure the DC voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short on the rail or its load; no voltage in S0 points to the rail not being enabled or its source missing.
PP5V_S0_KBD0.45––
AI: what PP5V_S0_KBD is and how to check it

Reference note for PP5V_S0_KBD on the 820-00239:

  • What it is: the 5 V keyboard rail that comes up in S0 (running) state, judging by the name. It's a switched rail, so it should only be present once the board is fully on, not in standby.
  • Known-good reading: diode 0.45 to ground, from the readings archive. There is no known-good voltage value here, so compare against a matching 5 V S0 rail or a known-good board.
  • How to check: with the board unpowered, measure diode mode from PP5V_S0_KBD to ground and expect around 0.45. Then power up, let the board reach S0, and measure the voltage; it should sit near 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points to the rail's enable or its source supply, not the rail itself. These are guides from community readings and vary with board state, so confirm before replacing anything.
PP5V_S0_T1390.45––
AI: what PP5V_S0_T139 is and how to check it

PP5V_S0_T139 — 820-00239 reference note

  • What it is: a 5 V rail that is switched on in the S0 (running) state, judged from the name; the "T139" suffix is just a rail identifier. The archive has no part list for this net, so which components sit on it isn't recorded.
  • Known-good reading: diode 0.45 to ground, from the community archive. No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source not switching. Confirm with a second measurement before replacing anything.
PP5V_S0_VCCSA0.473––
AI: what PP5V_S0_VCCSA is and how to check it

PP5V_S0_VCCSA is a 5 V rail that, judging by its name, belongs to the S0 (running) power state and supplies VCCSA. The only known-good figure here is a diode reading of 0.473 to ground; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure in diode mode from the rail to ground and compare with 0.473. A much lower reading suggests a short or a leaky part on the rail; a much higher one can mean an open path.
  • Then apply power and measure the voltage, but there is no known-good voltage here, so compare against a matching rail or a known-good board.
  • A reading far from known-good points to a fault on that rail, but one reading alone doesn't confirm a bad part.
PP5V_S0_VCORE20.467––
AI: what PP5V_S0_VCORE2 is and how to check it
  • What it is: PP5V_S0_VCORE2 is a 5 V rail; the "S0" in the name indicates it belongs to the running (S0) state, and "VCORE2" suggests a CPU core supply group, but that's from the name only.
  • Known-good reading: diode 0.467 to ground, from the readings archive. No known-good voltage is recorded here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on that rail; a much higher one to an open path. Confirm with a second point on the same net before replacing anything.
PP5V_S0SW_LCD0.56––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD — reference note

  • What it is: a 5 V rail switched in the S0 (running) state that feeds the LCD section; the S0SW part suggests it is switched on only once the board is in S0, and this reading is from the name, not from a schematic.
  • Known-good reading: diode-to-ground 0.56 in the readings archive. No known-good voltage reading here, and no condition is recorded for the 0.56.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.56. Then apply power, bring the board to S0, and measure the voltage — it should sit near 5 V, but that value is general expectation, not from this board's data.
  • If it's far off: a much lower diode reading points to a short or a leaky part on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. Neither is confirmed until traced.
PPVCC_S0_CPU0.0131.500–
AI: what PPVCC_S0_CPU is and how to check it
  • PPVCC_S0_CPU is the CPU core power rail; the "S0" in the name marks it as a running-state rail (from the name, not from board data).
  • Known-good readings for this board: diode 0.013 and voltage 1.500. These are community values and only a guide; the data gives no condition for them.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A very low diode reading is normal for a CPU core rail, so compare against the known-good 0.013 rather than judging it alone.
  • A voltage far from 1.500 with the board in S0 points to the CPU rail not coming up; confirm the rail's enable and input supply first. No known-good resistance reading exists here.
PPVCCEDRAM_S0_REG_F0.291.050–
AI: what PPVCCEDRAM_S0_REG_F is and how to check it

PPVCCEDRAM_S0_REG_F is a supply rail; the S0 in its name (from the name) marks it as a running-state rail, and the VCCEDRAM part suggests it feeds the eDRAM, though that's general inference, not from this board's data. Known-good here: diode 0.29 and 1.050 V, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A reading far from known-good usually points to a short or a failed source on that rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board.

PPVCCEDRAM_S0_REG_R0.1961.050–
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R — the name indicates a switched S0 (running-state) supply rail, likely for eDRAM, with a regulator output. From the readings archive, the known-good values are diode 0.196 to ground and 1.050 V with the board powered in S0; these are community readings and a guide only.

  • Check it unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.196.
  • Then power the board into S0 and measure the voltage, expecting about 1.050 V.
  • No known-good resistance reading exists for this rail, so compare against a matching rail on a known-good board if needed.

A diode reading far from 0.196 or a missing or wrong voltage usually points to a short, an open feed, or the regulator not being enabled — not proof of a bad part on one reading.

PPVCCGT_S0_CPU0.0021.5003.500R
AI: what PPVCCGT_S0_CPU is and how to check it
  • What it is: From the name, PPVCCGT_S0_CPU is the CPU graphics (GT) core supply, active in the S0 (running) state. It is a CPU power rail, not a startup rail.
  • Known-good readings (community guide): diode 0.002, voltage 1.500, resistance 3.500R. The data gives no condition for these, and no separate known-good value beyond these three.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power on and measure the voltage on the rail.
  • If far from known-good: a diode or resistance far off the 0.002 / 3.500R guide points at a short or a damaged supply or CPU side, but one reading isn't proof; compare with a known-good board before condemning a part.
PPVCCIO_S0_CPU0.0900.95075.000R
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is a CPU I/O supply rail; the "S0" suffix means it belongs to the running (S0) state, which comes from the rail's name. In the archive its known-good readings are diode 0.090, voltage 0.950 V and resistance 75.000R, with no condition noted, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board in S0. A reading far from these usually points to a short or open on the rail or its source, not proof of a bad part on one number. No known-good value exists here beyond those three, so compare against a matching rail or a known-good board.

PPVCCSA_S0_CPU0.0101.500–
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is the CPU system-agent power rail; the "S0" in the name marks it as a running-state rail (from the name, not from a schematic). The archive lists a known-good diode reading of 0.010 and a voltage of 1.500, with no condition noted, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.010 suggests a short or a leaky load on the rail; a voltage well off 1.500 with power applied points to the rail not coming up or being pulled down. There is no known-good resistance reading here, so compare against a matching rail or a known-good board.

PPVIN_S0_CPUVR_VIN0.37––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN is the CPU VRM input rail; the S0 in the name marks it as a running-state rail, and CPUVR_VIN means it feeds the CPU voltage regulator's input. The only known-good figure here is a diode reading of 0.37 to ground, with no condition recorded; there is no known-good voltage or resistance value for this rail.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.37.
  • Then power the board and measure the rail voltage; expect it near the adapter/battery bus level once the board is in S0, though no exact figure is recorded here.
  • A diode reading far below 0.37 suggests a short or a leaky part on the rail; far above it suggests an open path. Treat either as a lead, not a verdict, and check the feeding components before replacing anything.
PPVIN_S0SW_LCDBKLT0.86713.100–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT — reference note

  • What it is: the backlight input rail for the LCD, from the name: an S0 (running-state) switched supply feeding the display backlight. It is a general reading of the name, not from a schematic.
  • Known-good readings (community archive, guide only): diode 0.867 to ground, voltage 13.100 V. No known-good resistance value here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.867; then apply power and measure the rail voltage, expecting about 13.1 V once the board is in S0.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; no voltage with power applied points to the backlight enable or supply upstream. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT_F0.44513.100–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F — reference note

  • What it is: from the name, the switched input feed for the LCD backlight supply, enabled in the S0 (running) state. It is a backlight rail, not a main power rail.
  • Known-good readings (community archive, guide only): diode 0.445 to ground, voltage 13.100. No known-good resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.445; then power up and measure the voltage, expecting around 13.1 V once the board is in S0.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream at the backlight enable/switch path rather than the rail itself. Treat that as a likely cause, not a confirmed one, and check the enable side before replacing anything.
PPVIN_S0SW_LCDBKLT_R0.44513.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail for the LCD, and the S0 in the name (from the name) means it belongs to the running state, so it should only come up once the board is fully on. Known-good readings here are diode 0.445 and voltage 13.100; treat these as a community guide, since they vary with board state. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.445 suggests a short or leaky load on the backlight side, while a missing or much lower voltage with the board running points to the backlight supply not being enabled or its source rail being absent. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PPVOUT_S0_LCDBKLT1.20055.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight boost output; the S0 in the name marks it as a running-state rail, and the name indicates it feeds the LCD backlight. Known-good readings in the archive are diode 1.200 and voltage 55.000, with no condition noted, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, keeping clear of the panel connector and any high-voltage backlight wiring. A diode reading far from 1.200 usually points to a short or a leaky component on the rail, while a voltage well below 55.000 with the board running suggests the boost circuit isn't switching or its enable is missing. There is no known-good resistance reading for this rail.

Repair notes

CD3215 Repeat checks for each unit, U3100,3200, UB300, 400

UB300

1. Check 5V on FB200 pin 1 2. Check 3V3 on CB308 pin 1 1V8 on CB305 pin 1 1V8 on CB306 pin 1 1V1 on CB304 pin 1 3. Check 26V on QB300 pin 1 and QB300 pin 4 4. Check PPDCIN_G3H on QB300 pin 8

UB400

1. Check 5V on FB201 pin 1 2. Check 3V3 on CB408 pin 1 1V8 on CB405 pin 1 1V8 on CB406 pin 1 1V1 on CB404 pin 1 3. Check 26V on QB400 pin 1 and QB400 pin 4 4. Check PPDCIN_G3H on QB400 pin 8

U3100

1. Check 5V on F3000 pin 1 2. Check 3V3 on C3108 pin 1 1V8 on C3105 pin 1 1V8 on C3106 pin 1 1V1 on C3104 pin 1 3. Check 26V on Q3100 pin 1 and Q3100 pin 4 4. Check PPDCIN_G3H on Q3100 pin 8

U3200

1. Check 5V on F3001 pin 1 2. Check 3V3 on C3208 pin 1 1V8 on C3205 pin 1 1V8 on C3206 pin 1 1V1 on C3204 pin 1 3. Check 26V on Q3200 pin 1 and Q3200 pin 4 4. Check PPDCIN_G3H on Q3200 pin 8

CD3215 Sequence II

4. Check U6903 pin 10 3V3 (or 5V0) PM_EN_P3V3_G3H L6900 pin 2 3V3 PP3V3_G3H C5013 pin 1 1V2 PP1V2_G3H_SMC_VDDC C5167 pin 1 3V0 PP3V0_G3H_AVREF_SMC R3042 pin 1 3V3 (clock) SMBUS_SMC_4_G3H_SCL R3041 pin 1 3V3 (data) SMBUS_SMC_4_G3H_SDA C7016 pin 1 5V0 TBA_AUX_DET R7090 pin 2 3V3 SMC_RST_L D6902 pin 3 8V6/20V U7000 pin 10 P_IN U7000 pin 5 MPM_PBUS If still not finding anything, try ... Check TBA_VDDA and TBA_VDDP Measure R7075 for 4R7 value Check for EN (high) on PM_EN_P3V3_G3H Check 3V3 on R5940 pin 2 Check for EN (low) on HPWR_EN_L Check for EN (low) on SMC_WAKE_L (M13, WAKE_L) Check L5001 continuity and 3V3 Check R6915 continuity and 3V3

Power Sequences

5V to 20V ( U3200 based )

1. 5V PP20V_USBC_XB_VBUS at F3001 pin 1 2. Check CD3215 LDOs C3208 pin 1 3V3 C3205 pin 1 1V8 (LDOD) C3206 pin 1 1V8 (LDOA) C3204 pin 1 1V1 3. UPC_XB_GATE1 11V UPC_XB_GATE2 7V6 4. 3V3 PPVIN_G3H_P3V3G3H at D6902 pin 3 5. Check R7075 for value of ~4R7 5V TBA_VDDA at C7075 pin 1 6. 3V3 PM_EN_P3V3_G3H at U6903 pin 10 7. 3V3 PP3V3_G3H at R6915 pin 1 3V3 PP3V3_G3H_SMC_ISNS at L5001 pin 1 3V3 SMC_WAKE_L at R5002 pin 2 3V3 HPWR_EN_L at R7009 pin 2 8. 1V2 PP1V2_G3H_SMC_VDDC at C5013 pin 1 (TP nearby) 3V3 SMC_4FINGERS_RST at U5256 pin 4 (TP nearby) ~3V0 SMBUS_SMC_5_G3_SCL at R5381 pin 2 ~3V0 SMBUS_SMC_5_G3_SDA at R5380 pin 2 9. 3V0 PP3V0_G3H_AVREF_SMC at C5166 pin 1 (TP nearby) Generated by U5165 3V3 SMC_LID at R5255 pin 2 3V3 SMC_LID_LEFT at R5256 pin 2 3V3 SMC_LID_RIGHT at R5261 pin 2 3V3 SMC_RST_L at R7090 pin 1 10. 0V6 DM SMBUS_SMC_4_G3H_SCL at R3042 pin 2 0V6 DM SMBUS_SMC_4_G3H_SDA at R3041 pin 2 11. 0V6 DM USBC_XB_CC1 at C3213 pin 1 0V6 DM USBC_XB_CC2 at C3214 pin 1 12. 20V PP20V_USBC_XB_VBUS at F3001 pin 1 13. UPC_XB_GATE1 26V 14. UPC_XB_GATE2 20V 15. ~5V0 TBA_AUX_DET at R7015 pin 2 16. 3V3 SMC_AUX_OK at Q5490 pin 2 17. Q7030 and Q7040 driven to generate PPBUS_G3H 18. 20V PPBUS_G3H should now be present

Every net with a reading

NetDiodeVoltageResistance
50_0_ANT0.000––
50_1_ANT0.000––
50_2_ANT0.000––
8409_SPKR_ID00.74––
ACT_GND0.00––
ALL_SYS_PWRGD0.45––
ALS_SCL_I2C_1V80.460––
ALS_SDA_I2C_1V80.460––
ALS_SOC_UART_D2R0.530––
ALS_SOC_UART_R2D0.530––
AMP_CODEC_RT_I2C_SCL0.490––
AMP_CODEC_RT_I2C_SDA0.500––
AMP_LT_I2C_SCL0.506––
AMP_LT_I2C_SDA0.519––
AMP_TR_LRCLK0.520––
AMP_TR_SCLK0.523––
AMP_TR_SDOUT0.359––
AMP_WR_LRCLK0.503––
AMP_WR_SCLK0.513––
AMP_WR_SDOUT0.339––
ANI01_VREF0.427––
ANI23_VREF0.427––
ANI45_VREF0.430––
ANI67_VREF0.429––
AP_CLKREQ_L0.570––
AP_PCIE_WAKE_L0.518––
AP_RESET_L0.790––
AUD_3V3_S00.330––
AUD_ASP1A_LRCLK0.521––
AUD_ASP1A_SCLK0.516––
AUD_ASP1A_SDOUT0.355––
AUD_ASP1B_LRCLK0.513––
AUD_ASP1B_SCLK0.508––
AUD_ASP1B_SDOUT0.345––
AUD_ASP2_LRCLK0.670––
AUD_ASP2_SCLK0.560––
AUD_ASP2_SDIN0.694––
AUD_ASP2_SDOUT0.560––
AUD_CONN_HP_LEFT0.64––
AUD_CONN_HP_RIGHT0.64––
AUD_CONN_HP_SENSE_L1.45––
AUD_CONN_HP_SENSE_R1.43––
AUD_CONN_RING20.01––
AUD_CONN_RING2_XW0.63––
AUD_CONN_SLEEVE0.01––
AUD_CONN_SLEEVE_XW0.63––
AUD_CONN_TIP_SENSE1.52––
AUD_HP_PORT_CH_GND0.010––
AUD_HP_PORT_L0.640––
AUD_HP_PORT_R0.640––
AUD_HP_PORT_US_GND0.010––
AUD_HP_SENSE_L1.450––
AUD_HP_SENSE_R1.450––
AUD_HS_MIC_N0.630––
AUD_HS_MIC_P0.630––
AUD_PWR_EN0.538––
BKLT_EN_R0.4620.014–
BKLT_PWM_KEYB0.5380.000–
BKLT_PWM_MLB2TCON0.78––
BKLT_PWM_TCON2MLB0.74––
BKLT_SCL0.5335.000–
BKLT_SD0.5936.500–
BKLT_SDA0.5335.000–
BKLT_SENSE_OUT0.7270.167–
BMON_IOUTOL––
BT_I2S_CLK0.525––
BT_I2S_CLK_1V80.525––
BT_I2S_D2R0.525––
BT_I2S_D2R_1V80.525––
BT_I2S_R2D_1V80.525––
BT_I2S_SYNC_1V80.520––
BT_ROM_BOOT_L0.520––
BT_SFLASH_CS_L0.700––
BT_SFLASH_HOLD_L0.732––
BT_SFLASH_WP_L0.729––
BT_SPI2_CLK0.724––
BT_SPI2_CLK_ROL––
BT_SPI2_CSN0.762––
BT_SPI2_CSN_ROL––
BT_SPI2_MISO0.612––
BT_SPI2_MISO_ROL––
BT_SPI2_MOSI0.630––
BT_SPI2_MOSI_ROL––
BT_SWDCLK0.760––
BT_SWDIO0.760––
BT_TIMESTAMP0.750––
BT_UART_CTS_R2D_L0.685––
BT_UART_D2R0.708––
BT_UART_R2D0.683––
BT_UART_RTS_D2R_L0.708––
BUF_EDP_PANEL_PWR_EN0.69––
BUF_SMC_RESET_L0.700––
CHGR_AMON0.61––
CHGR_BMON0.61––
CODEC_INT_L0.718––
CODEC_RESET_L0.724––
COMP_A_CPUGT0.62––
COMP_B_CPUCORE0.62––
COMP_C_CPUSA0.62––
CORE2_5G_CTL2_WLAN_JTAG_TDO0.596––
CPU_CATERR_L0.233––
CPU_CFG<0>0.290––
CPU_CFG<1>0.290––
CPU_CFG<2>0.290––
CPU_CFG<3>0.281––
CPU_CFG<4>0.270––
CPU_CFG<5>0.287––
CPU_CFG<6>0.290––
CPU_CFG<7>0.290––
CPU_CFG<8>0.284––
CPU_CFG<9>0.285––
CPU_CFG<10>0.285––
CPU_CFG<11>0.287––
CPU_CFG<12>0.290––
CPU_CFG<13>0.285––
CPU_CFG<14>0.290––
CPU_CFG<15>0.290––
CPU_CFG<16>0.290––
CPU_CFG<17>0.290––
CPU_CFG<18>0.290––
CPU_CFG<19>0.286––
CPU_DIMM_VREFCA0.696––
CPU_PECI0.345––
CPU_PECI_R0.316––
CPU_PROCHOT_L0.485––
CPU_PROCHOT_L_R0.51––
CPU_VCCST_PWRGD0.452––
CPU_VR_EN_R0.45––
CPUCORE_BOOT10.607––
CPUCORE_BOOT20.607––
CPUCORE_BP10.604––
CPUCORE_BP20.604––
CPUCORE_FCCM0.60––
CPUCORE_ISEN10.62––
CPUCORE_ISEN20.62––
CPUCORE_ISNS1_N–1.500–
CPUCORE_ISNS1_P–1.500–
CPUCORE_ISNS2_N–1.500–
CPUCORE_ISNS2_P–1.500–
CPUCORE_ISUMN_R0.24––
CPUCORE_ISUMP0.43––
CPUCORE_PHASE10.009––
CPUCORE_PSYS0.62––
CPUCORE_PWM10.60––
CPUCORE_PWM20.60––
CPUCORE_SW10.0061.5005.700R
CPUCORE_SW20.006–5.700R
CPUCORE_SW2_SNUBOL––
CPUCORE1_DRVHOL––
CPUCORE1_GL00.460––
CPUCORE2_DRVH0.456––
CPUCORE2_GL00.622––
CPUGT_BOOT10.610––
CPUGT_BOOT30.610––
CPUGT_FCCM0.59––
CPUGT_ISEN10.62––
CPUGT_ISEN20.62––
CPUGT_ISEN30.62––
CPUGT_ISNS1_N–1.500–
CPUGT_ISNS1_P–1.500–
CPUGT_ISNS2_N–1.500–
CPUGT_ISNS2_P–1.500–
CPUGT_ISNS3_N–1.500–
CPUGT_ISNS3_P–1.500–
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN_R0.29––
CPUGT_ISUMP0.29––
CPUGT_PHASE10.010––
CPUGT_PHASE30.010––
CPUGT_PWM10.60––
CPUGT_PWM20.60––
CPUGT_PWM30.60––
CPUGT_SW10.0031.5002.800R
CPUGT_SW20.0032.5002.800R
CPUGT_SW30.0031.5002.800R
CPUGT1_DRVHOL––
CPUGT3_DRVHOL––
CPUGT3_GL00.460––
CPUHI_COMP_FBOL––
CPUHI_COMP_VREFOL––
CPUHI_IOUT0.685––
CPUSA_BOOTSA0.622––
CPUSA_BPSA0.616––
CPUSA_DRVHOL––
CPUSA_FCCM0.60––
CPUSA_GL00.450––
CPUSA_ISNS_N0.0101.500–
CPUSA_ISNS_P0.0101.500–
CPUSA_ISUMN_R0.37––
CPUSA_ISUMP0.56––
CPUSA_PHASESA0.020––
CPUSA_PWM0.60––
CPUSA_SW_SNUBOL––
CPUTHMSNS_ADDR_SEL0.645––
CPUTHMSNS_ALERT_L0.592––
CPUTHMSNS_D1_N0.666––
CPUTHMSNS_D1_P0.666––
CPUTHMSNS_D2_N0.666––
CPUTHMSNS_D2_P0.666––
CPUTHMSNS_D3_N0.666––
CPUTHMSNS_D3_P0.666––
CPUTHMSNS_FILTER0.450––
CPUTHMSNS_THM_L0.553––
CPUVR_ISUM_IOUTOL––
CPUVR_PGOOD0.50––
CPUVR_SWSA0.0101.0489.300R
CPUVR_VIDALERT_L_R0.28––
CPUVR_VIDSCLK_R0.28––
CPUVR_VIDSOUT_R0.25––
DBGLED_S0OL––
DBGLED_S4OL––
DBGLED_S5OL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.486––
DDI1_MUX_EN0.700––
DEBUGUART_SEL_SOC0.690––
DFR_CLKIN_RESET_L0.47––
DFR_DISP_INT0.440––
DFR_DISP_PWR_EN0.510––
DFR_DISP_RESET_L0.470––
DFR_DISP_RST_L0.470––
DFR_DISP_SMC_RST_L0.533––
DFR_DISP_TE0.440––
DFR_DISP_VSYNC0.440––
DFR_TOUCH_GPIO20.46––
DFR_TOUCH_INT_L0.47––
DFR_TOUCH_LID0.49––
DFR_TOUCH_PANEL_DETECT0.46––
DFR_TOUCH_RESET_L0.47––
DFR_TOUCH_ROM_I2C_SCL0.46––
DFR_TOUCH_ROM_I2C_SDA0.46––
DFR_TOUCH_ROM_WC0.46––
DFR_TOUCH_SPI_CLK_R0.47––
DFR_TOUCH_SPI_CS_L0.47––
DFR_TOUCH_SPI_MISO_R0.47––
DFR_TOUCH_SPI_MOSI_R0.47––
DFRDRV_I2C_SCL0.440––
DFRDRV_I2C_SDA0.440––
DFU_SPI_STATUS0.475––
DMIC1_CLK0.77––
DMIC1_DATA0.74––
DMIC2_CLK0.77––
DMIC2_DATA0.74––
DP_DDI1_ML_C_N<0>0.219––
DP_DDI1_ML_C_P<0>0.219––
DP_DDI2_ML_C_N<0>0.222––
DP_DDI2_ML_C_P<0>0.228––
DP_DDPB_HPD0.590––
DP_INT_HPD0.78––
DP_T_SNK_RBIAS0.790––
DP_T_SNK0_DDC_CLK0.610––
DP_T_SNK0_HPD0.559––
DP_T_SNK1_DDC_CLK0.610––
DP_T_SNK1_DDC_DATA0.606––
DP_T_SNK1_HPD0.547––
DP_T_SRC_RBIAS0.804––
DP_TA_AUXCH_N0.820––
DP_TA_AUXCH_P0.816––
DP_TA_HPD0.600––
DP_TB_AUXCH_N0.816––
DP_TB_AUXCH_P0.816––
DP_TB_HPD0.603––
DP_X_SNK0_HPD0.55––
DP_X_SNK1_HPD0.54––
DP_XA_HPD0.60––
DP_XB_AUXCH_P0.820––
DP_XB_HPD0.596––
EDP_BKLT_EN–3.350–
EDP_INT_AUX_N0.24––
EDP_INT_AUX_P0.24––
EDP_INT_ML_N<0>0.24––
EDP_INT_ML_N<1>0.24––
EDP_INT_ML_N<2>0.24––
EDP_INT_ML_N<3>0.24––
EDP_INT_ML_P<0>0.24––
EDP_INT_ML_P<1>0.24––
EDP_INT_ML_P<2>0.25––
EDP_INT_ML_P<3>0.24––
EDP_PANEL_PWR_EN0.566––
ESD_GNDOL––
FAN_LT_PWM0.94––
FAN_LT_TACHOL––
FAN_RT_PWM0.940––
FAN_RT_TACHOL––
FB_A_CPUGT0.60––
FB_B_CPUCORE0.58––
FB_C_CPUSA0.59––
GND_5V3V3_AGND0.00––
GND_FAN0.01––
HALL_SENSOR_LEFT0.487––
HALL_SENSOR_RIGHT0.517––
HDA_SDIN00.722––
HPWR_EN_L0.61––
HS_MIC_N0.733––
HS_OTHER3V3_IOUTOL––
HS_OTHER5V_IOUTOL––
I2C_ALS_SCL0.54––
I2C_ALS_SCL_R0.500––
I2C_ALS_SDA0.54––
I2C_ALS_SDA_R0.500––
I2C_BKLT_SCL0.53––
I2C_BKLT_SDA0.53––
I2C_CAM_SCL0.46––
I2C_CAM_SDA0.46––
I2C_TBT_T_SCL0.58––
I2C_TBT_T_SDA0.58––
I2C_TBT_TA_INT_L0.58––
I2C_TBT_TB_INT_L0.58––
I2C_TBT_X_SCL0.60––
I2C_TBT_X_SDA0.60––
I2C_TBT_XA_INT_L0.59––
I2C_TBT_XB_INT_L0.59––
I2C_UPC_T_SCL20.68––
I2C_UPC_T_SDA20.68––
I2C_UPC_TA_DBG_CTL_SCL0.776––
I2C_UPC_TA_DBG_CTL_SDA0.770––
I2C_UPC_TB_DBG_CTL_SCL0.777––
I2C_UPC_TB_DBG_CTL_SDA0.777––
I2C_UPC_X_SCL20.68––
I2C_UPC_X_SDA20.68––
I2C_UPC_XA_DBG_CTL_SCL0.76––
I2C_UPC_XA_DBG_CTL_SDA0.76––
IMON_A_CPUGT0.62––
IMON_B_CPUCORE0.62––
IMON_C_CPUSA0.62––
ISNS_1V0_N–1.000–
ISNS_1V0_P–1.000–
ISNS_1V8_SUS_NOL––
ISNS_1V8_SUS_POL––
ISNS_BT_NOL––
ISNS_BT_POL––
ISNS_CAMERA_NOL––
ISNS_CAMERA_POL––
ISNS_CPUDDR_N–1.200–
ISNS_CPUDDR_P–1.200–
ISNS_CPUEDRAM_IOUTOL––
ISNS_CPUEDRAM_N–1.050–
ISNS_CPUEDRAM_P–1.050–
ISNS_CPUHIGAIN_N0.455––
ISNS_CPUHIGAIN_P0.455––
ISNS_CPUSA_IOUTOL––
ISNS_HS_COMPUTING_N0.445––
ISNS_HS_COMPUTING_P0.445––
ISNS_HS_OTHER5V_NOL––
ISNS_HS_OTHER5V_POL––
ISNS_KBBLT_IOUTOL––
ISNS_LCDBKLT_N0.44513.100–
ISNS_LCDBKLT_P0.44513.100–
ISNS_LPDDR_IOUTOL––
ISNS_LPDDR_N–1.800–
ISNS_LPDDR_P–1.800–
ISNS_PCHCORE_IOUTOL––
ISNS_PCHPRIMCORE_N–1.000–
ISNS_PCHPRIMCORE_P–1.000–
ISNS_PICCOLO_IOUTOL––
ISNS_PP3V3S0_NOL––
ISNS_PP3V3S0_POL––
ISNS_PP3V3S4_WLAN_NOL––
ISNS_PP3V3S4_WLAN_POL––
ISNS_PP3V3S4_WLAN_R_NOL––
ISNS_PP3V3S4_WLAN_R_POL––
ISNS_SSDNAND_IOUTOL––
ISNS_SSDNAND_N0.3372.700–
ISNS_SSDNAND_P–2.700–
ISNS_T151_IOUTOL––
ISNS_T151_NOL––
ISNS_T151_POL––
ISNS_TBT_NOL––
ISNS_TBT_POL––
ISNS_TBT_T_IOUTOL––
ISNS_TPAD_NOL––
ISNS_TPAD_POL––
ISNS_WLAN_OPOL––
ISNS_X239_INT_IOL––
ISNS_X239_INT_NIOL––
ISNS_X239_IOUTOL––
ISNS_X239_IOUT_BUFOL––
ISNS_X239_IOUT_INTOL––
ITP_PMODE0.483––
JTAG_ISP_TDO0.552––
JTAG_TBT_T_TMS0.615––
JTAG_TBT_X_TMS0.597––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_I2C_SCLOL––
KBD_I2C_SDAOL––
KBD_INT_LOL––
L83_FILT0.813––
L83_FLYC0.414––
L83_FLYN0.520––
L83_HSBIAS_FILT0.722––
L83_LDO_EN0.525––
L83_SDOUT0.669––
L83_SDOUT_R0.667––
L83_VCP0.394––
L83_VCP_FILTN0.640––
L83_VCP_FILTP0.406––
L83_VL0.394––
L83_VP0.315––
LCD_IRQ_L0.78––
LCD_PWR_SLEW_3V30.627––
LCDBKLT_EN_LOL9.400–
LCDBKLT_FB0.72337.000–
LCDBKLT_FET_DRV0.4941.000–
LCDBKLT_FET_DRV_R0.5021.000–
LCDBKLT_SW0.4360.011–
LCDBKLT_TB_XWR1.20043.000–
LPC_CLK24M_SMC0.752––
LPC_PWRDWN_L0.746––
LPSR_EN_LB_L0.5400.545 LIFEBOAT%5fREMOVED––
MENU_KEY_L0.73––
MESA_BOOST_EN0.530––
MESA_BOOST_EN_CONN1.06––
MESA_I2C_SCL0.48––
MESA_I2C_SDA0.48––
MESA_PWR_EN0.486––
MESA_SNSR_INT_CONN1.05––
MESA_SPI_CLK_CONN0.53––
MESA_SPI_MISO0.500––
MESA_SPI_MISO_CONN0.48––
MESA_SPI_MOSI_CONN0.48––
MIPI_CLK_CONN_N0.54––
MIPI_CLK_CONN_P0.53––
MIPI_DATA_CONN_N0.55––
MIPI_DATA_CONN_P0.55––
MIPID_CLK_CONN_N0.480––
MIPID_CLK_CONN_P0.480––
MIPID_CLK_N0.480––
MIPID_CLK_P0.480––
MIPID_DATA_CONN_N0.480––
MIPID_DATA_CONN_P0.480––
MIPID_DATA_N0.480––
MIPID_DATA_P0.480––
MLB_BOARD_ID00.800––
MLB_BOARD_ID10.800––
MLB_BOARD_ID20.799––
MLB_BOARD_ID40.800––
MLB_RAMCFG00.800––
MLB_RAMCFG10.740––
MLB_RAMCFG30.758––
MLB_RAMCFG40.758––
NAND_WP_L0.495––
NAND_ZQ_U91000.305––
NTC_A_CPUGT0.62––
NTC_B_CPUCORE0.62––
NTC_B_CPUCORE_ROL––
P0V9_FIXED_SW0.2900.900–
P0V9_REG_SW00.2280.900–
P0V9_REG_SW10.2280.900–
P0V9_TBT_T_SVR_AGND0.000––
P1V0PCH_DRVL0.485––
P1V0PCH_PGOOD0.457––
P1V0PCH_PHASE0.090–89.000R
P1V0PCH_REG_R0.1001.00089.000R
P1V0PCH_SW_SNUBOL––
P1V0S0_IOUTOL––
P1V0S0SW_RAMP0.623––
P1V2_DRVH_R0.797––
P1V2_DRVL0.485––
P1V2_DRVL_R0.480––
P1V2_HOT_SW0.3001.200–
P1V2_PHASE0.2551.200250.000
P1V2_SW0.258––
P1V2_SW_SNUBOL––
P1V8_COLD_SW00.2901.800–
P1V8_COLD_SW10.2901.800–
P1V8_HOT_SW0.49––
P1V8S0_RAMP0.628––
P1V8S3_EN0.510––
P1V8SUS_PGOOD0.473––
P1V8SUS_SW0.3101.800–
P1VEDRAM_DRVH_R0.720––
P1VEDRAM_DRVL_R0.494––
P1VOPC_SNS0.30––
P1VS0SW_EN_RC0.577––
P1VS4_DRVH0.670––
P1VS4_DRVL0.488––
P1VS4_PHASE0.1201.000119.00R
P1VS4_SW0.124––
P1VS4_SW_SNUBOL––
P1VSUS_PGOOD0.480––
P2V7NAND_AGND0.002––
P2V7NAND_DRVH0.800––
P2V7NAND_DRVH_R0.800––
P2V7NAND_DRVL0.456––
P2V7NAND_EN0.519––
P2V7NAND_FSEL0.550––
P2V7NAND_LL0.333––
P2V7NAND_OCSET0.546––
P2V7NAND_PGOOD0.47––
P2V7NAND_PGOOD_R0.510––
P2V7NAND_R0.3252.700322.000
P2V7NAND_RTN_DIV0.545––
P2V7NAND_SENSE_DIV0.544––
P2V7NAND_SET00.552––
P2V7NAND_SET10.549––
P2V7NAND_SREF0.548––
P2V7NAND_SW0.3252.700322.000
P2V7NAND_VBST0.610––
P2V7NAND_VO0.545––
P3V3_TBT_T_SX_EN0.580––
P3V3_TBT_T_SX_EN_R0.590––
P3V3_TBT_X_SX_EN0.627––
P3V3G3H_AGND0.00––
P3V3G3H_BIAS0.55––
P3V3G3H_FB0.58––
P3V3G3H_FB_R0.380––
P3V3G3H_FB_RC1.449––
P3V3G3H_LX0.35––
P3V3G3H_VBST0.60––
P3V3S0_RAMP0.627––
P3V3S0SW_RAMP0.711––
P3V3S4_EN_R0.520––
P3V3S4_RAMP0.610––
P3V3S5_COMP20.73––
P3V3S5_CSN20.373.300–
P3V3S5_CSP21.20––
P3V3S5_CSP2_R0.3723.300–
P3V3S5_DRVH0.91––
P3V3S5_DRVL0.55––
P3V3S5_DRVL_R0.557––
P3V3S5_EN0.46––
P3V3S5_RF0.56––
P3V3S5_SW0.37––
P3V3S5_TG0.930––
P3V3S5_VBST0.62––
P3V3S5_VFB20.550.990–
P3V3S5_VFB2_R0.380––
P3V3S5_VFB2_RR0.767––
P3V3S5_VSW0.3703.300–
P5VP3V3_SKIPSEL0.47––
P5VP3V3_VREF20.47––
P5VP3V3_VREG30.54––
P5VS0_EN0.467––
P5VS4_COMP10.73––
P5VS4_COMP1_ROL––
P5VS4_CSN10.415.000–
P5VS4_CSP10.90––
P5VS4_CSP1_R–5.000–
P5VS4_DRVH0.96––
P5VS4_DRVL0.55––
P5VS4_EN0.50––
P5VS4_EN_RDOL––
P5VS4_FET_RAMP0.630––
P5VS4_PGOOD0.45––
P5VS4_SW0.41––
P5VS4_TG0.980––
P5VS4_VBST0.62––
P5VS4_VFB10.56––
P5VS4_VSW0.4245.000–
P5VS5_EN0.46––
P5VUSBC_T_AGND0.012––
P5VUSBC_T_DRVH0.645––
P5VUSBC_T_DRVH_R0.627––
P5VUSBC_T_DRVL0.439––
P5VUSBC_T_FSEL0.531––
P5VUSBC_T_LL0.1905.000186.000
P5VUSBC_T_NEG0.1955.000–
P5VUSBC_T_OCSET0.540––
P5VUSBC_T_POS0.1955.000–
P5VUSBC_T_R0.1955.000186.000
P5VUSBC_T_RTN_DIV0.529––
P5VUSBC_T_RTN_DIV_R0.002––
P5VUSBC_T_SENSE_DIV0.537––
P5VUSBC_T_SENSE_DIV_R0.187––
P5VUSBC_T_SET_ROL––
P5VUSBC_T_SET00.548––
P5VUSBC_T_SET10.533––
P5VUSBC_T_SREF0.548––
P5VUSBC_T_VBST0.433––
P5VUSBC_T_VO0.540––
P5VUSBC_X_DRVL0.460––
P5VUSBC_X_LL0.204–203.000
P5VUSBC_X_NEG0.210––
P5VUSBC_X_PGOOD0.544––
P5VUSBC_X_POS0.210––
P5VUSBC_X_R0.210–203.000
P16V0_AGND0.000––
PANEL_FET_EN_DLY0.700––
PANEL_P3V3_EN0.576––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.45013.100–
PBUSVSENS_EN_L0.418––
PBUSVSENS_EN_L_DIVOL––
PCH_ALS_TO_SOC_UART_TXD0.470––
PCH_BT_UART_CTS_L0.706––
PCH_BT_UART_D2R0.695––
PCH_BT_UART_R2D0.720––
PCH_HSIO_PWR_EN0.803––
PCH_JTAGX0.055––
PCH_SOC_FORCE_DFU0.468––
PCH_SOC_WDOG0.579––
PCH_SRTCRST_L0.817––
PCH_SSD_SOC_UART_D2R0.656––
PCH_SSD_SOC_UART_R2D0.666––
PCH_STRP_TOPBLK_SWP_L0.788––
PCH_SWD_IO0.670––
PCH_SWD_MUX_SEL0.580––
PCH_TO_SOC_UART_TXD0.470––
PCH_USB2_COMP0.126––
PCIE_CLK100M_AP_N0.348––
PCIE_CLK100M_AP_P0.348––
PCIE_CLK100M_SSD_LB_N0.3500.423 LIFEBOAT%5fREMOVED––
PCIE_CLK100M_SSD_LB_P0.3480.423 LIFEBOAT%5fREMOVED––
PCIE_CLK100M_SSD_N0.312 LIFEBOAT%5fREMOVED––
PCIE_CLK100M_SSD_P0.315 LIFEBOAT%5fREMOVED––
PCIE_CLK100M_TBT_T_N0.362––
PCIE_CLK100M_TBT_T_P0.362––
PCIE_CLK100M_TBT_X_N0.351––
PCIE_CLK100M_TBT_X_P0.348––
PCIE_SSD_D2R_LB_N<0>OL LIFEBOAT%5fREMOVED––
PCIE_SSD_D2R_LB_P<0>OL LIFEBOAT%5fREMOVED––
PCIE_SSD_D2R_N<0>0.4030.368 LIFEBOAT%5fREMOVED––
PCIE_SSD_D2R_P<0>0.4020.366 LIFEBOAT%5fREMOVED––
PCIE_SSD_R2D_C_N<0>0.333 LIFEBOAT%5fREMOVED––
PCIE_SSD_R2D_C_P<0>0.333 LIFEBOAT%5fREMOVED––
PCIE_SSD_R2D_LB_C_N<0>OL LIFEBOAT%5fREMOVED––
PCIE_SSD_R2D_LB_C_P<0>OL LIFEBOAT%5fREMOVED––
PCIE_TBT_T_D2R_N<0>0.400––
PCIE_TBT_T_D2R_P<0>0.400––
PCIE_TBT_X_D2R_N<0>0.395––
PCIE_TBT_X_D2R_P<0>0.399––
PD_L0.46––
PD_SOC_UART_CTS_L0.800––
PDCINVSENS_EN_L_DIVOL––
PICCOLO_IREFOL––
PICCOLO_IUVDOL––
PICCOLO_NOR_CS_L0.34––
PICCOLO_PGOOD1.84––
PICCOLO_PID01.84––
PICCOLO_PID11.70––
PICCOLO_POK2OL––
PICCOLO_VDD_RTCOL––
PICCOLO_VEN10.49––
PICCOLO_VPP_OTP1.70––
PICCOLO_VPUMPOL––
PICCOLO_VREFOL––
PICCOLO_WP_L0.50––
PLT_RST_L0.668––
PM_BATLOW_L0.557––
PM_DSW_PWRGD0.755––
PM_EN_P3V3_G3H0.59––
PM_PCH_PWROK0.466––
PM_PCH_SYS_PWROK0.549––
PM_PWRBTN_L0.728––
PM_RSMRST_L0.481––
PM_SLP_S0_L0.480––
PM_SLP_S3_L0.470––
PM_SLP_S4_L0.488––
PM_SLP_S5_L0.514––
PM_SLP_SUS_L0.476––
PM_SYSRST_L0.739––
PM_THRMTRIP_L0.266––
PMIC_VINVR50.46413.100–
PMU_TO_SOC_AWAKE_PWRGD0.450––
PMU_VREF0.555––
PP_STOCKHOLM_TVDD0.365––
PP_STOCKHOLM_VMID0.563––
PP0V6_S0_DDRVTT0.091––
PP0V6_S3_MEM_VREFCA_A0.692––
PP0V6_S3_MEM_VREFDQ_A0.748––
PP0V6_S3_MEM_VREFDQ_B0.748––
PP0V6_SLEEP1_BUCK00.3480.600–
PP0V6_SLEEP2_LDO00.376––
PP0V8_SLEEP1_SW10.152––
PP0V8_SLEEP2_BUCK10.2370.800–
PP0V9_PLL_C_DVDD030.241––
PP0V9_PLL_DVDD470.243––
PP0V9_PLL_DVDD8110.250––
PP0V9_SSD_FIXED0.2900.900–
PP0V9_SSD_REG0.2280.900–
PP0V9_TBT_T_CIO0.386––
PP0V9_TBT_T_DP0.316––
PP0V9_TBT_T_LVR0.268––
PP0V9_TBT_T_PCIE0.307––
PP0V9_TBT_T_SVR0.2500.900–
PP0V9_TBT_X_CIO0.41––
PP0V9_TBT_X_DP0.000––
PP0V9_TBT_X_LVR0.260––
PP0V9_TBT_X_PCIE0.283––
PP0V9_TBT_X_SVR0.2340.900–
PP0V9_TBT_X_USB0.485––
PP1V_PCH_REG_R0.1201.000119.000
PP1V_SUS_PCH_VCCCLK2_F0.1351.000–
PP1V_SUS_PCH_VCCCLK4_F0.1351.000–
PP1V_SUS_PCH_VCCCLK5_F0.1351.000–
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.1351.000–
PP1V0_S0SW0.223––
PP1V0_S30.225––
PP1V0_SUS0.1351.000–
PP1V0_SUSSW0.1351.000–
PP1V1_SLEEP1_PLL_DDR_FILT0.410––
PP1V1_SLEEP1_SW20.410––
PP1V1_SLEEP1_XTAL_FILT0.400––
PP1V1_SLEEP3_BUCK20.2951.100–
PP1V1_UPC_TB_LDO_BMC0.528––
PP1V1_UPC_XA_LDO_BMC0.50––
PP1V1_UPC_XB_LDO_BMC0.511.10–
PP1V2_G3H_SMC_VDDC0.522––
PP1V2_S0SW0.262––
PP1V2_S30.241.200–
PP1V2_S3_CPUDDR0.261––
PP1V2_S3_REG_R0.2551.200250.000
PP1V2_SSD_COLD0.24––
PP1V2_SSD_HOT0.3001.200–
PP1V8_ALWAYS_LDO90.394––
PP1V8_AUDIO0.393––
PP1V8_AWAKE_SW3C0.34––
PP1V8_MESA0.540––
PP1V8_MESA_CONN0.53––
PP1V8_PLL_AVDD8110.325––
PP1V8_S00.360––
PP1V8_S0_PCH_VCCHDA_F0.355––
PP1V8_S0SW_DFR0.500––
PP1V8_S30.3741.800–
PP1V8_S3_MEM0.3751.800–
PP1V8_S40.430––
PP1V8_SLEEP2_SW3A0.44––
PP1V8_SLEEP3_BUCK30.401.800–
PP1V8_SSD_COLD0.2901.800–
PP1V8_SSD_HOT0.490––
PP1V8_SUS0.317––
PP1V8_SUS_REG_R0.3101.800–
PP1V8_UPC_TA_LDOA0.530––
PP1V8_UPC_TA_LDOD0.492––
PP1V8_UPC_TB_LDOA0.533––
PP1V8_UPC_TB_LDOD0.497––
PP1V8_UPC_XA_LDOA0.51––
PP1V8_UPC_XA_LDOD0.48––
PP1V8_UPC_XB_LDOA0.51––
PP1V8_UPC_XB_LDOD0.481.80–
PP1V25_PMICVREF0.493––
PP2V5_ADC2_VREFOL––
PP2V7_NAND_PVCC0.446––
PP2V7_NAND_VCC0.450––
PP2V9_SYSCLK0.465––
PP3V0_AWAKE_LDO70.553––
PP3V0_G3H0.454––
PP3V0_G3H_AVREF_SMC0.594––
PP3V0_MESA0.566––
PP3V0_MESA_CONN0.56––
PP3V3_2V7_NAND_VCC0.342.700–
PP3V3_G3H0.35––
PP3V3_G3H_REG_R0.372––
PP3V3_G3H_SMC_VDDA0.363––
PP3V3_PMICLDO0.426––
PP3V3_S00.330––
PP3V3_S0_CPUTHMSNS_TI_R0.320––
PP3V3_S0SW_DFR0.530––
PP3V3_S0SW_LCD0.56––
PP3V3_S0SW_LCD_R0.572––
PP3V3_S40.370––
PP3V3_S4_BT0.370––
PP3V3_S4_MESA0.369––
PP3V3_S4_MESA_SW0.369––
PP3V3_S4_SOC_PMU0.364––
PP3V3_S4_TPAD0.33––
PP3V3_S4_WLAN_SW0.340––
PP3V3_S4_WLAN_SW_R0.340––
PP3V3_S4SW_SNSOL––
PP3V3_S50.3700.355 LIFEBOAT%5fREMOVED3.300–
PP3V3_S5_SSD0.34––
PP3V3_S5_SSD_LB0.3720.443 LIFEBOAT%5fREMOVED––
PP3V3_S5_T1390.376––
PP3V3_S5_TBT_T_SW0.482––
PP3V3_S5_TBT_X_SW0.48––
PP3V3_SUS0.352––
PP3V3_TBT_T_ANA_PCIE0.522––
PP3V3_TBT_T_ANA_USB20.492––
PP3V3_TBT_T_F0.3093.300–
PP3V3_TBT_T_LC0.536––
PP3V3_TBT_T_S00.3093.300–
PP3V3_TBT_X_ANA_PCIE0.508––
PP3V3_TBT_X_ANA_USB20.479––
PP3V3_TBT_X_F0.310––
PP3V3_TBT_X_LC0.53––
PP3V3_TBT_X_S00.310––
PP3V3_UPC_TA_LDO0.5263.300–
PP3V3_UPC_TB_LDO0.516––
PP3V3_UPC_XA_LDO0.50––
PP3V3_UPC_XB_LDO0.503.30–
PP5V_COREVR_VCC0.41––
PP5V_PMICLDO0.467––
PP5V_S00.45––
PP5V_S0_ALSCAM_F0.45––
PP5V_S0_BKLT_A0.4615.130–
PP5V_S0_BKLT_D0.4625.000–
PP5V_S0_FAN_CONN0.45––
PP5V_S0_KBD0.45––
PP5V_S0_T1390.45––
PP5V_S0_VCCSA0.473––
PP5V_S0_VCORE20.467––
PP5V_S0SW_LCD0.56––
PP5V_S40.1200.422 LIFEBOAT%5fREMOVED5.000–
PP5V_S4_P2V7NAND_LB0.4230.466 LIFEBOAT%5fREMOVED––
PP5V_S4_T_USBC0.1955.000–
PP5V_S4_TPAD_CONN0.41––
PP5V_S4_WLAN_ISNS_DOL––
PP5V_S4_X_USBC0.2105.000–
PP5V_S50.45––
PP5V_USBC_T_PVCC0.417––
PP5V_USBC_T_VCC0.417––
PP16V0_MESA0.666––
PP16V0_MESA_CONN0.65––
PP17V0_MOJAVE_LDOIN0.605––
PP20V_USBC_TA_VBUS0.15320.000–
PP20V_USBC_TA_VBUS_CONN0.16720.000–
PP20V_USBC_TA_VBUS_F0.15320.000–
PP20V_USBC_TB_VBUS0.15020.000–
PP20V_USBC_TB_VBUS_CONN0.16020.000–
PP20V_USBC_TB_VBUS_F0.15020.000–
PP20V_USBC_XA_VBUS0.1420.000–
PP20V_USBC_XA_VBUS_CONN0.15520.000–
PP20V_USBC_XA_VBUS_F–20.000–
PP20V_USBC_XB_VBUS0.150––
PP20V_USBC_XB_VBUS_CONN0.020––
PP20V_USBC_XB_VBUS_F0.15––
PPBUS_G3H0.4450.435 LIFEBOAT%5fREMOVED13.100–
PPBUS_G3H_R0.460––
PPBUS_HS_CPU0.445––
PPBUS_HS_OTH3V30.42––
PPBUS_HS_OTH5V0.445––
PPBUS_PMIC0.457––
PPBUS_S4_HS_TPAD0.445––
PPDCIN_G3H0.5420.000–
PPDCIN_G3H_CHGR0.5420.000–
PPDCIN_G3H_CHGR_R0.570––
PPDCPRTC_PCH0.700––
PPSVDD_STOCKHOLM0.343––
PPVBAT_G3H_CHGR_R0.44513.100–
PPVBAT_G3H_CHGR_REG0.44513.100–
PPVBAT_G3H_CONN0.62––
PPVCC_CPU_PH10.0061.5005.700R
PPVCC_CPU_PH20.0061.5005.700R
PPVCC_S0_CPU0.0131.500–
PPVCCEDRAM_PHASE0.1961.050–
PPVCCEDRAM_S0_REG_F0.291.050–
PPVCCEDRAM_S0_REG_R0.1961.050–
PPVCCGT_CPU_PH10.0031.5002.800R
PPVCCGT_CPU_PH20.0031.5002.800R
PPVCCGT_CPU_PH30.0031.5002.800R
PPVCCGT_S0_CPU0.0021.5003.500R
PPVCCIO_S0_CPU0.0900.95075.000R
PPVCCPRIMCORE_SUS_PCH0.1101.000–
PPVCCSA_CPU_R0.0101.0509.300R
PPVCCSA_S0_CPU0.0101.500–
PPVDD_STOCKHOLM0.303––
PPVIN_2V7NAND_LB0.430.869 LIFEBOAT%5fREMOVED2.700–
PPVIN_G3H_P3V3G3HOL––
PPVIN_S0_CPUVR_VIN0.37––
PPVIN_S0SW_LCDBKLT0.86713.100–
PPVIN_S0SW_LCDBKLT_F0.44513.100–
PPVIN_S0SW_LCDBKLT_R0.44513.100–
PPVIN_S4_TPAD_FUSE0.445––
PPVIN_SW_LCDBKLT_SW0.86713.000–
PPVOUT_S0_LCDBKLT1.20055.000–
PROG1_CPUCOREVR0.61––
PROG2_CPUCOREVR0.61––
PROG3_CPUCOREVR0.59––
PROG4_CPUCOREVR0.61––
PROG5_CPUCOREVR0.62––
PVCCCORE_PH1_AGND0.001––
PVCCCORE_PH2_AGND0.002––
PVCCCSA_AGND0.006––
PVCCEDRAM_AGND0.00––
PVCCEDRAM_DRVH0.60––
PVCCEDRAM_DRVL0.43––
PVCCEDRAM_LL0.29––
PVCCEDRAM_MODE0.52––
PVCCEDRAM_REFIN0.67––
PVCCEDRAM_S3_EN0.49––
PVCCEDRAM_TRIP0.73––
PVCCEDRAM_VBST0.61––
PVCCEDRAM_VREF0.62––
PVCCEDRAM_VTT0.60––
PVCCEDRAM_VTTREF0.48––
PVCCIO_DRVH0.625––
PVCCIO_DRVL0.480––
PVCCIO_PGOOD0.483––
PVCCIO_PHASE0.0760.95075.000R
PVCCIO_SW0.079––
RIO_SPKRAMP_BSTP_10.602––
RIO_SPKRAMP_BSTP_20.600––
RIO_TBTTHMSNS_D1_N0.003––
RIO_TBTTHMSNS_D1_P0.620––
RTC_RESET_L0.822––
RTN_A_CPUGT0.00––
RTN_B_CPUCORE0.00––
RTN_C_CPUSA0.00––
S2R_ACK_L0.476––
S3X_COLD_BOOT_L0.39––
S3X_DDR_PHY_DATA_VREF0.600––
S3X_DEBUG_UART_D2R0.39––
S3X_DEBUG_UART_R2D0.39––
S3X_EXT_SE_24MHZ_CLK_IN0.007––
S3X_HOLD_RESET0.437––
S3X_I2C_SCL0.428––
S3X_I2C_SDA0.428––
S3X_JTAG_SEL0.440––
S3X_JTAG_TCK0.445––
S3X_JTAG_TDI0.444––
S3X_JTAG_TDO0.442––
S3X_JTAG_TMS0.444––
S3X_JTAG_TRST_L0.445––
S3X_PCIE_CLKREQ_L0.39––
S3X_PERST_L0.39––
S3X_PFN0.39––
S3X_PMIC_CTRL00.39––
S3X_PMIC_CTRL10.39––
S3X_PMIC_EXT_CLK_DIS0.39––
S3X_PMIC_LOW_PWR0.39––
S3X_RESET_L0.39––
S3X_RET_EN_L0.62––
S3X_RET_LPSR_CLEAR0.39––
S3X_SMC_OOB_UART_D2R0.38––
S3X_SMC_OOB_UART_R2D0.39––
S5_PWRGD0.48––
SEP_I2C_SCL0.476––
SEP_I2C_SDA0.474––
SEP_ROM_WC0.753––
SMBUS_PCH_CLK0.778––
SMBUS_PCH_DATA0.768––
SMBUS_SMC_0_S0_SCL0.71––
SMBUS_SMC_0_S0_SDA0.71––
SMBUS_SMC_1_S0_SCL0.615––
SMBUS_SMC_1_S0_SDA0.607––
SMBUS_SMC_3_SCL0.56––
SMBUS_SMC_3_SDA0.55––
SMBUS_SMC_4_G3H_SCL0.700––
SMBUS_SMC_4_G3H_SDA0.680––
SMBUS_SMC_5_G3_SCL0.42––
SMBUS_SMC_5_G3_SDA0.42––
SMC_4FINGERS_RST0.60––
SMC_ACTUATOR_DISABLE_L0.74––
SMC_AUX_OK0.60––
SMC_BT_PWR_EN0.711––
SMC_CHGR_INT_L0.60––
SMC_CPUDDR_ISENSE0.753––
SMC_CPUEDRAM_ISENSE0.758––
SMC_CPUGT_IMON_ISENSE0.735––
SMC_CPUGT_ISENSE0.757––
SMC_CPUHI_COMP_ALERT_LOL––
SMC_DDR1V2_ISENSE0.748––
SMC_DEBUGPRT_RX_L0.737––
SMC_DEBUGPRT_TX_L0.737––
SMC_DEV_SUPPLY_L0.765––
SMC_FAN_0_CTL0.760––
SMC_FAN_0_TACH0.762––
SMC_FAN_1_CTL0.750––
SMC_FAN_1_TACH0.759––
SMC_LIDOL––
SMC_LID_R0.726––
SMC_LSOC_RST_L0.739––
SMC_ONOFF_L0.740––
SMC_OOB_UART_D2R_R0.71––
SMC_OOB1_D2R_L0.622––
SMC_OOB1_R2D_L0.544––
SMC_PCHPRIMCORE_ISENSE0.755––
SMC_PECI_L0.738––
SMC_PM_G2_EN0.555––
SMC_PME_S4_DARK_L0.550––
SMC_PME_S4_WAKE_L0.74––
SMC_PROCHOT_L0.540––
SMC_RESET_L0.727––
SMC_RST_L0.60––
SMC_SENSOR_PWR_EN0.746––
SMC_SOCPMU_RESET0.555––
SMC_TCK0.756––
SMC_TDI0.755––
SMC_TDO0.755––
SMC_THRMTRIP_L0.340––
SMC_TMS0.755––
SMC_USBC_INT_L0.68––
SMC_VIBE_L0.74––
SMC_WIFI_PWR_EN0.500––
SML_PCH_0_CLK0.766––
SML_PCH_0_DATA0.800––
SOC_ALS_LS_EN0.510––
SOC_DBG_UART_D2R0.545––
SOC_DBG_UART_R2D0.540––
SOC_FORCE_DFU0.473––
SOC_JTAG_SEL0.46––
SOC_PMU_BUCK0_LX0.3480.600–
SOC_PMU_BUCK1_FB0.152––
SOC_PMU_BUCK1_LX0.2370.800–
SOC_PMU_BUCK2_LX0.2951.100–
SOC_PMU_BUCK3_LX0.4001.800–
SOC_PMU_CLK_32K0.430––
SOC_ROM_SPI_CLK_R0.440––
SOC_ROM_SPI_CS_L0.480––
SOC_ROM_SPI_MISO_R0.410––
SOC_ROM_SPI_MOSI_R0.470––
SOC_ROM_SPI_RST_L0.613––
SOC_ROM_SPI_WP_L0.558––
SOC_S2R_ACK_L0.794––
SOC_SWCLK0.47––
SOC_SWCLK_DBG0.500––
SOC_SWD_CLK0.660––
SOC_SWD_LS_EN0.510––
SOC_SWDIO0.47––
SOC_SWDIO_DBG0.500––
SOC_TO_PCH_ALS_UART_TXD0.470––
SOC_TO_PCH_UART_TXD0.470––
SOC_TO_STOCKHOLM_EN0.480––
SOC_UART_LS_EN0.560––
SOC_XB_DBG1_1V80.510––
SOC_XB_DBG2_1V80.507––
SOC_XTAL_24M_I0.815––
SOC_XTAL_24M_O_R0.800––
SPI_ALT_CLK0.610––
SPI_ALT_CS_L0.712––
SPI_ALT_IO0_MOSI0.740––
SPI_ALT_IO1_MISO0.750––
SPI_ALT_IO2_WP_L0.613––
SPI_ALT_IO3_HOLD_L0.746––
SPI_CLK0.613––
SPI_CS0_L0.720––
SPI_IO2_R0.610––
SPI_IO3_R0.745––
SPI_MISO_R0.746––
SPI_MLB_CLK0.590––
SPI_MLB_CS_L0.704––
SPI_MLB_IO0_MOSI0.726––
SPI_MLB_IO1_MISO0.723––
SPI_MLB_IO2_WP_L0.589––
SPI_MLB_IO3_HOLD_L0.731––
SPI_MLBROM_CS_L0.650––
SPI_MOSI0.744––
SPIROM_USE_MLB0.719––
SPKRAMP_5V_WR0.548––
SPKRAMP_BSTP_10.600––
SPKRAMP_BSTP_20.600––
SPKRAMP_BSTP_30.600––
SPKRAMP_BSTP_40.600––
SPKRAMP_TL_OUT_N0.570––
SPKRAMP_TL_OUT_P0.570––
SPKRAMP_TR_OUT_N0.580––
SPKRAMP_TR_OUT_P0.580––
SPKRAMP_WL_OUT_N0.570––
SPKRAMP_WL_OUT_P0.570––
SPKRAMP_WR_OUT_N0.580––
SPKRAMP_WR_OUT_P0.580––
SPKRCONN_TL_OUT_N0.57––
SPKRCONN_TL_OUT_P0.57––
SPKRCONN_TR_OUT_N0.58––
SPKRCONN_TR_OUT_P0.58––
SPKRCONN_WL_OUT_N0.57––
SPKRCONN_WL_OUT_P0.57––
SPKRCONN_WR_OUT_N0.58––
SPKRCONN_WR_OUT_P0.58––
SPROM_CLK0.667––
SPROM_CS0.687––
SPROM_DIN0.652––
SPROM_DOUT0.689––
SSD_BOOT_L0.4400.773 LIFEBOAT%5fREMOVED––
SSD_BOOT_LB_L0.4400.418 LIFEBOAT%5fREMOVED––
SSD_CLKREQ_L0.5561.577 LIFEBOAT%5fREMOVED––
SSD_DBG_UART_D2R0.630––
SSD_DBG_UART_D2R_R0.66––
SSD_DBG_UART_R2D0.550––
SSD_DBG_UART_R2D_R0.680––
SSD_PCIE_CLKREQ_LB_L0.5550.547 LIFEBOAT%5fREMOVED––
SSD_PWR_EN_L0.7940.621 LIFEBOAT%5fREMOVED––
SSD_PWR_EN_LB_L0.795OL LIFEBOAT%5fREMOVED––
SSD_PWR_REQ0.500––
SSD_RESET_L0.5600.774 LIFEBOAT%5fREMOVED––
SSD_RESET_LB_L0.5580.546 LIFEBOAT%5fREMOVED––
SSD_SR_EN_L0.5300.558 LIFEBOAT%5fREMOVED––
STORAGE_EN0.560OL LIFEBOAT%5fREMOVED––
STORAGE_LB_EN0.5600.548 LIFEBOAT%5fREMOVED––
SW1_EXT_ON0.550––
SYS_DETECT_LOL––
SYSCLK_CLK32K_WIFIBT0.470––
TBA_AUX_DET0.61––
TBA_BGATE0.62––
TBA_BOOT10.57––
TBA_BOOT1_RC0.57––
TBA_BOOT20.57––
TBA_BOOT2_RC0.57––
TBA_COMP0.61––
TBA_CSI_N0.5420.0002.900R
TBA_CSI_P0.5420.0002.900R
TBA_CSI_R_N0.5420.000–
TBA_CSI_R_P0.5420.000–
TBA_CSO_N0.4313.1003.100R
TBA_CSO_P0.4313.1003.100R
TBA_CSO_R_N0.44513.100–
TBA_CSO_R_P0.44513.100–
TBA_GATE_Q10.79––
TBA_GATE_Q20.98––
TBA_GATE_Q30.99––
TBA_GATE_Q40.80––
TBA_LX10.350––
TBA_LX20.350––
TBA_MPM_DET0.60––
TBA_PHASE10.35013,100–
TBA_PHASE20.35013,100–
TBA_VDDA0.45––
TBA_VDDP0.44––
TBT_POC_RESET0.68––
TBT_T_CIO_PLUG_EVENT_L0.604––
TBT_T_CIO_PWR_EN0.57––
TBT_T_CLKREQ_L0.600––
TBT_T_FORCE_PWR0.606––
TBT_T_PCI_RESET_L0.602––
TBT_T_ROM_HOLD_L0.711––
TBT_T_ROM_WP_L0.596––
TBT_T_SPI_CLK0.572––
TBT_T_SPI_CLK_DBG0.64––
TBT_T_SPI_CS_L0.600––
TBT_T_SPI_MISO0.610––
TBT_T_SPI_MOSI0.609––
TBT_T_TEST_PWR_GOOD0.110––
TBT_T_TMU_CLK_IN0.550––
TBT_T_USB_PWR_EN0.57––
TBT_TA_LSRX0.604––
TBT_TA_LSTX0.604––
TBT_TB_LSRX0.605––
TBT_TB_LSTX0.607––
TBT_X_CIO_PLUG_EVENT_L0.61––
TBT_X_PCI_RESET_L0.60––
TBT_X_ROM_HOLD_L0.710––
TBT_X_ROM_WP_L0.585––
TBT_X_SPI_CLK0.566––
TBT_X_SPI_CLK_DBG0.65––
TBT_X_SPI_CS_L0.594––
TBT_X_SPI_MISO0.596––
TBT_X_SPI_MOSI0.600––
TBT_X_TMU_CLK_IN0.550––
TBT_X_USB_PWR_EN0.587––
TBT_XA_LSRX0.591––
TBT_XA_LSTX0.592––
TBT_XB_LSRX0.600––
TBT_XB_LSTX0.600––
TBTTHMSNS_ALERT_L0.575––
TBTTHMSNS_ALERT_T_L0.562––
TBTTHMSNS_D1_N0.000––
TBTTHMSNS_D1_P0.630––
TBTTHMSNS_THM_T_L0.572––
TBTTPOCRST_CT0.757––
TBTTPOCRST_SNS1.400––
TBTXPOCRST_SNSOL––
TP_CPU_PWRGD0.417––
TP_DPMUX_SAK_60.709––
TP_DPMUX_SAK_130.711––
TP_ISNS_PP3V3G3H_SMCNOL––
TP_ISNS_PP3V3G3H_SMCPOL––
TP_Q3100_DRAIN0.59––
TP_Q3200_DRAIN0.60––
TP_SMC_DEV_SUPPLY_L0.762––
TP_SOC_CLKOUT0.47––
TP_SOC_JTAG_TDI0.47––
TP_SOC_JTAG_TDO0.471––
TP_SOC_JTAG_TRST_L0.47––
TP_SOC_TST_CKOUT0.471––
TP_UPC_TA_SWD_CLK0.751––
TP_UPC_TA_SWD_DATA0.751––
TP_UPC_TB_SWD_CLK0.755––
TP_UPC_TB_SWD_DATA0.757––
TP_UPC_XA_SWD_CLK0.744––
TP_UPC_XA_SWD_DATA0.744––
TP_UPC_XB_SWD_CLK0.75––
TP_UPC_XB_SWD_DATA0.74––
TP_USB_TESTERN0.610––
TP_USB_TESTERP0.628––
TP_USB3_03_D2RN0.390––
TP_USB3_03_D2RP0.400––
TP_USB3_03_R2DN0.360––
TP_USB3_03_R2DP0.360––
TP_USBC_PP20V_TAOL––
TP_USBC_PP20V_TBOL––
TP_USBC_PP20V_XBOL––
TPAD_SPI_CLK_R0.81––
TPAD_SPI_CS_CONN_R_L0.94––
TPAD_SPI_CS_L0.778––
TPAD_SPI_IF_EN0.745––
TPAD_SPI_IF_EN_CONN0.68––
TPAD_SPI_INT_CONN_L0.67––
TPAD_SPI_INT_L0.620––
TPAD_SPI_MISO_R0.81––
TPAD_SPI_MOSI_R0.81––
UNCONNECTED_2OL––
UNCONNECTED_3OL––
UNCONNECTED_101OL––
UNCONNECTED_507OL––
UNCONNECTED_5910.59––
UPC_T_5V_EN0.529––
UPC_TA_DBG10.755––
UPC_TA_DBG30.778––
UPC_TA_DBG40.778––
UPC_TA_GATE10.661––
UPC_TA_GATE20.652––
UPC_TA_SSOL––
UPC_TA_UART_RX0.75––
UPC_TA_UART_TX0.76––
UPC_TB_DBG30.788––
UPC_TB_DBG40.780––
UPC_TB_GATE10.662––
UPC_TB_GATE20.652––
UPC_TB_R_OSC0.500––
UPC_TB_SS0.535––
UPC_X_5V_EN0.54––
UPC_XA_GATE10.64––
UPC_XA_GATE20.63––
UPC_XA_SS0.530––
UPC_XA_UART_RX0.75––
UPC_XA_UART_TX0.75––
UPC_XB_DBG_UART_RX0.780––
UPC_XB_DBG_UART_TX0.780––
UPC_XB_GATE10.65––
UPC_XB_GATE20.65––
UPC_XB_R_OSC0.540––
UPC_XB_SS0.550––
USB_CAMERA_DFR_N0.622––
USB_CAMERA_DFR_P0.622––
USB_UPC_PCH_TA_N0.624––
USB_UPC_PCH_TA_P0.624––
USB_UPC_PCH_TB_N0.625––
USB_UPC_PCH_TB_P0.625––
USB_UPC_PCH_XA_N0.62––
USB_UPC_PCH_XA_P0.62––
USB_UPC_PCH_XB_N0.730––
USB_UPC_PCH_XB_P0.730––
USB_UPC_TA_F_N0.624––
USB_UPC_TA_F_P0.624––
USB_UPC_TB_F_N0.625––
USB_UPC_TB_F_P0.625––
USB_UPC_XA_F_N0.62––
USB_UPC_XA_F_P0.620––
USB_UPC_XB_F_N0.730––
USB_UPC_XB_F_P0.730––
USB3_EXTA_D2R_N0.44––
USB3_EXTA_D2R_P0.44––
USB3_EXTA_R2D_C_N0.382––
USB3_EXTA_R2D_C_P0.387––
USB3_EXTA_R2D_N0.777––
USB3_EXTA_R2D_P0.777––
USBC_T_RESET_L0.737––
USBC_T_RESET_L_R0.549––
USBC_TA_CC10.624––
USBC_TA_CC20.623––
USBC_TA_D2R_N<1>0.350––
USBC_TA_D2R_N<2>0.360––
USBC_TA_D2R_P<1>0.350––
USBC_TA_D2R_P<2>0.654––
USBC_TA_R2D_N<1>OL––
USBC_TA_R2D_N<2>OL––
USBC_TA_R2D_P<1>OL––
USBC_TA_R2D_P<2>OL––
USBC_TA_SBU10.920––
USBC_TA_SBU20.855––
USBC_TA_USB_BOT_NOL––
USBC_TA_USB_BOT_POL––
USBC_TA_USB_TOP_NOL––
USBC_TA_USB_TOP_P0.912––
USBC_TB_CC10.620––
USBC_TB_CC20.622––
USBC_TB_D2R_N<1>0.350––
USBC_TB_D2R_N<2>0.350––
USBC_TB_D2R_P<1>0.350––
USBC_TB_D2R_P<2>0.350––
USBC_TB_R2D_N<1>OL––
USBC_TB_R2D_N<2>OL––
USBC_TB_R2D_P<1>OL––
USBC_TB_SBU10.847––
USBC_TB_SBU20.838––
USBC_TB_USB_BOT_NOL––
USBC_TB_USB_BOT_P0.900––
USBC_TB_USB_TOP_NOL––
USBC_TB_USB_TOP_P0.930––
USBC_X_RESET_L0.72––
USBC_XA_CC10.60––
USBC_XA_CC20.611––
USBC_XA_D2R_N<2>0.358––
USBC_XA_D2R_P<1>0.355––
USBC_XA_D2R_P<2>0.358––
USBC_XA_R2D_N<1>OL––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<1>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_SBU10.860––
USBC_XA_SBU20.850––
USBC_XA_USB_DBG_BOT_N0.960––
USBC_XA_USB_DBG_BOT_P0.960––
USBC_XA_USB_DBG_TOP_NOL––
USBC_XA_USB_DBG_TOP_POL––
USBC_XB_CC10.610––
USBC_XB_CC20.628––
USBC_XB_D2R_N<1>0.351––
USBC_XB_D2R_N<2>0.350––
USBC_XB_D2R_P<1>0.351––
USBC_XB_D2R_P<2>0.350––
USBC_XB_R2D_N<1>OL––
USBC_XB_R2D_N<2>OL––
USBC_XB_R2D_P<1>OL––
USBC_XB_R2D_P<2>OL––
USBC_XB_SBU1OL––
USBC_XB_SBU20.850––
USBC_XB_USB_BOT_NOL––
USBC_XB_USB_BOT_POL––
USBC_XB_USB_TOP_NOL––
USBC_XB_USB_TOP_POL––
VR_P0V9_FIXED_FB0.24––
VR_P0V9_REG_FB0.12––
VR_P1V2_HOT_FB0.29––
VR_P1V8_COLD_FB0.27––
VR_P1V8_HOT_FB0.49––
VR0V9_IND_TBT_T0.2500.900–
VR0V9_IND_TBT_X0.2340.900–
WIFI_SROM_ORG0.700––
WIFI_SW_CAP0.700––
WLAN_JTAG_SEL0.588––
WLAN_JTAG_TCK0.570––
WLAN_JTAG_TDI0.587––
WLAN_JTAG_TMS0.598––
WLAN_JTAG_TRST_L0.566––
WLAN_UART_RX0.580––
WLAN_UART_TX0.580––
XDP_BPM_L<0>0.288––
XDP_CPU_PRDY_L0.254––
XDP_CPU_PREQ_L0.279––
XDP_CPU_PWRBTN_L0.735––
XDP_CPU_TCK0.055––
XDP_CPU_TDI0.237––
XDP_CPU_TDO0.217––
XDP_CPU_TMS0.235––
XDP_CPU_TRST_L0.280––
XDP_DBRESET_L0.735––
XDP_JTAG_ISP_TCK0.590––
XDP_JTAG_ISP_TDI0.580––
XDP_PCH_OBSDATA_A20.800––
XDP_PCH_OBSDATA_A30.792––
XDP_PCH_OBSDATA_B00.800––
XDP_PCH_OBSDATA_C00.802––
XDP_PCH_OBSDATA_C10.792––
XDP_PCH_OBSDATA_C20.800––
XDP_PCH_OBSDATA_C30.792––
XDP_PCH_OBSDATA_D00.800––
XDP_PCH_OBSDATA_D10.800––
XDP_PCH_OBSDATA_D20.803––
XDP_PCH_OBSDATA_D30.800––
XDP_PCH_OBSFN_C10.794––
XDP_PCH_TCK0.405––
XDP_PCH_TDI0.242––
XDP_PCH_TDO0.224––
XDP_PCH_TMS0.240––
XDP_PCH_TRST_L0.293––
XDP_PRESENT_L0.515––
XDP_USB_EXTA_OC_L0.760––
XDP_USB_EXTB_OC_L0.758––
XDP_USB_EXTC_OC_L0.760––
XDP_USB_EXTD_OC_L0.761––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00239?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00239: diode 0.445, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00239?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00239: diode 0.35. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00239?

OpenBoardData's known-good values for PP5V_S5 on the 820-00239: diode 0.45. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00239 board?

Open your own 820-00239 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License