Apple laptop board · OpenBoardData
820-01814 known-good readings
Known-good readings for the Apple laptop board 820-01814: 2,149 nets, including 94 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 83 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-01814.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 94 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 39
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_G3S | 0.330 | 1.800 | – |
AI: what PP1V8_G3S is and how to check itPP1V8_G3S is a 1.8 V rail; the "G3S" part of the name indicates it belongs to the always-on G3 group, so it should be present whenever the board has standby power. Known-good readings from the archive are diode 0.330 and voltage 1.800. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.330 suggests a short or leaky load on the rail; a voltage well off 1.800 points to a supply or loading fault. No known-good resistance reading is available for this rail. | |||
PP1V8_G3S_WLANBT_VDDIO | 0.331 | – | – |
AI: what PP1V8_G3S_WLANBT_VDDIO is and how to check itPP1V8_G3S_WLANBT_VDDIO is a 1.8 V always-on rail feeding the WLAN/Bluetooth I/O supply, judged from its name (G3S = always on). The archive lists one known-good diode reading of 0.331 to ground; there's no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.331 suggests a short or leaky part on that net, but one reading alone doesn't confirm a bad part. | |||
PP3V0_G3H_RTC | 0.517 | – | – |
AI: what PP3V0_G3H_RTC is and how to check itPP3V0_G3H_RTC is the 3.0 V always-on rail that feeds the RTC circuit, judged from its name (G3H = always on, RTC = real-time clock). The archive lists one known-good diode reading for this net: 0.517, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the net. No known-good voltage reading is listed here, so compare against a matching always-on rail or a known-good board. A diode reading far from 0.517 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part. | |||
PP3V3_G3H_DFR | 0.432 | 3,300 | – |
AI: what PP3V3_G3H_DFR is and how to check itPP3V3_G3H_DFR is an always-on 3.3 V rail, judged from the G3H part of its name; "DFR" likely marks a variant or sub-rail, but that isn't confirmed here. The archived readings give a diode value of 0.432 and a voltage of 3,300 (3.3 V), with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well below 3.3 V or a diode reading far from 0.432 points to a fault on that rail or its load, but one reading alone doesn't confirm a bad part; no known-good resistance reading is available for this rail. | |||
PP3V3_G3H_MESA_SW | 0.423 | – | – |
AI: what PP3V3_G3H_MESA_SW is and how to check itPP3V3_G3H_MESA_SW is a 3.3 V always-on rail, going by the G3H part of its name; "MESA" and "SW" suggest it feeds the MESA section through a switch, but that's inference from the name, not from board data. The only known-good reading here is a diode value of 0.423 to ground, with no condition recorded and no known-good voltage listed. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the net. A diode reading far from 0.423 usually points to a short or a leaky part on the rail, while a correct diode reading with no voltage points upstream at the rail's source or its enable. | |||
PP3V3_G3H_PMU_VINRTC_R | 0.429 | – | – |
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check itPP3V3_G3H_PMU_VINRTC_R is an always-on 3.3 V rail feeding the PMU's RTC input, judged from the name (G3H = always on, VINRTC = RTC supply). The only known-good reading here is a diode value of 0.429 to ground; no known-good voltage reading is recorded for this rail.
A diode reading far below 0.429 usually points to a short or a leaky part on the rail; a much higher or open reading suggests a broken trace or missing connection. Confirm with a second measurement before replacing anything. | |||
PP3V3_G3H_RTC_REG_R | 0.429 | 3,300 | 0.010R |
AI: what PP3V3_G3H_RTC_REG_R is and how to check itPP3V3_G3H_RTC_REG_R is a 3.3 V always-on rail, judging from its name (G3H = always on, RTC = real-time clock, REG = regulator output). The archive lists a known-good diode reading of 0.429 to ground and 3,300 (3.3 V) with power applied; the 0.010R resistance figure is also listed but its condition isn't stated, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.429 suggests a short or leaky load on the rail; a correct diode reading with missing 3.3 V points back toward the regulator feeding it. No known-good resistance reading with a stated condition is available here, so compare against a matching rail or a known-good board. | |||
PP3V3_G3H_RTC_X | 0.41 | – | – |
AI: what PP3V3_G3H_RTC_X is and how to check itPP3V3_G3H_RTC_X is the always-on 3.3 V rail that keeps the RTC (real-time clock) powered, judged from its name: G3H usually means always-on, and RTC is the clock domain. The archive lists one known-good reading: diode 0.41, with no condition noted. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far from 0.41 can point to a short or a damaged component on the rail, but one reading alone isn't proof. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. | |||
PP3V3_G3H_SOCPMU | 0.427 | – | – |
AI: what PP3V3_G3H_SOCPMU is and how to check it
| |||
PP3V3_G3H_SSD0_SNS | 0.425 | 3,300 | – |
AI: what PP3V3_G3H_SSD0_SNS is and how to check itPP3V3_G3H_SSD0_SNS is a 3.3 V always-on rail feeding SSD0 sensing, judging by the name (G3H = always on, SNS = sense). Known-good readings from the archive: diode 0.425 to ground and 3,300 mV with power applied. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied. A diode reading far from 0.425 suggests a short or leaky part on the rail; a voltage well below 3,300 mV points to the rail not coming up or being loaded down. No known-good resistance reading is available here, so compare against a matching net or a known-good board. | |||
PP3V3_G3H_SSD1_SNS | OL | – | – |
AI: what PP3V3_G3H_SSD1_SNS is and how to check itPP3V3_G3H_SSD1_SNS is a 3.3 V always-on rail feeding SSD1 sense circuitry; the G3H part of the name indicates it should be present whenever the board has power, and SSD1_SNS marks it as a sense line for the first SSD. The only archived reading is a diode value of OL, with no condition recorded, so there is no known-good voltage or resistance here to compare against. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the same point. A diode reading far from OL, or a voltage that is missing or well off 3.3 V, usually points to a short or a failed source on that rail, but one reading alone doesn't confirm a bad part; compare with the matching SSD sense rail on the other side if the board has one. | |||
PP3V3_G3H_T | 0.427 | 3,300 | 425.200 |
AI: what PP3V3_G3H_T is and how to check itPP3V3_G3H_T is the always-on 3.3 V rail; the G3H part of the name indicates it's present whenever power is connected, before the board is switched on. Archived readings for this rail are diode 0.427, voltage 3,300 (3.3 V) and resistance 425.200; these are community values and vary with board state, so treat them as a guide only.
A single off reading isn't proof a part is bad; confirm with a second measurement before replacing anything. | |||
PP3V3_G3HSW_DFR | 0.56 | – | – |
AI: what PP3V3_G3HSW_DFR is and how to check itPP3V3_G3HSW_DFR is a 3.3 V rail; the G3H part of the name indicates it is always on (from the name, not from a schematic).
| |||
PP3V3_G3S_AUD_F | 0.337 | – | – |
AI: what PP3V3_G3S_AUD_F is and how to check it
| |||
PP3V3_G3S_T | 0.339 | – | – |
AI: what PP3V3_G3S_T is and how to check itPP3V3_G3S_T is a 3.3 V rail; the G3S in its name marks it as an always-on startup-stage supply (from the name). The only known-good reading here is a diode value of 0.339 to ground, with no condition noted; there is no known-good voltage reading in this data.
| |||
PP3V3_G3S_WLAN | 0.353 | – | – |
AI: what PP3V3_G3S_WLAN is and how to check itPP3V3_G3S_WLAN is a 3.3 V rail for the WLAN section, and the G3S in its name indicates it is an always-on rail (from the name). The archive lists one known-good diode reading of 0.353 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.353 usually points to a short or leaky component on that rail, but a single reading doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything. | |||
PP3V3_G3S_X | 0.352 | – | – |
AI: what PP3V3_G3S_X is and how to check itPP3V3_G3S_X is a 3.3 V always-on rail, judged from its name (G3S/G3H-style naming usually means it comes up with the first power stage). The only known-good reading here is a diode value of 0.352 to ground; there is no known-good voltage or resistance reading for it.
| |||
PP3V3_G3SSW_SNS | 0.517 | – | – |
AI: what PP3V3_G3SSW_SNS is and how to check itPP3V3_G3SSW_SNS is a 3.3 V always-on rail, judging from its name (PP = power rail, 3V3 = 3.3 V, G3 = always-on group, SNS = sense). The archive lists one known-good diode reading for it: 0.517, with no condition noted, so treat it as a guide. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. No known-good voltage reading is recorded here, so compare against a matching always-on rail or a known-good board. A diode reading far from 0.517 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. | |||
PP5V_G3S | 0.408 | 5,000 | – |
AI: what PP5V_G3S is and how to check itPP5V_G3S is a 5 V rail; the "G3S" suffix marks it as an always-on (G3H) startup rail, which comes from the rail's name. The archive lists a known-good diode reading of 0.408 and a voltage of 5,000 (5 V), with no condition noted, so treat these as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.408 suggests a short or a leaky load on the rail; a voltage well off 5 V points to the supply side or an overload. No known-good resistance reading exists for this rail. | |||
PP5V_G3S_BKLT_A | 0.409 | – | – |
AI: what PP5V_G3S_BKLT_A is and how to check itPP5V_G3S_BKLT_A is a 5 V backlight rail; the G3S in the name marks it as an always-on (G3H) supply, and BKLT points to the display backlight. The only known-good reading here is a diode value of 0.409 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the DC voltage with power applied. No known-good voltage reading exists here, so compare against a matching backlight rail or a known-good board. A diode reading far below 0.409 usually suggests a short or leaky part on the rail, but one reading alone doesn't confirm a fault. | |||
PP5V_G3S_BKLT_D | 0.410 | – | – |
AI: what PP5V_G3S_BKLT_D is and how to check itPP5V_G3S_BKLT_D is a 5 V backlight-related rail; the G3S part of the name indicates it is always on (from the name, not from a schematic). The only known-good reading here is a diode value of 0.410 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.410 usually points to a short or a leaky component on that rail, but one reading alone isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
PP5V_G3S_DFR_FILT | 0.39 | – | – |
AI: what PP5V_G3S_DFR_FILT is and how to check itPP5V_G3S_DFR_FILT is a 5 V rail; the G3S part of the name indicates it is an always-on (G3H) startup rail, and "FILT" suggests it is a filtered version of that supply. The only known-good reading here is a diode value of 0.39 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the net to ground, then power the board and measure the DC voltage on the same net. A diode reading far below 0.39 usually points to a short or a leaky part on the rail, while a much higher reading can mean an open connection; a missing or low voltage with power applied points upstream toward the source of the 5 V supply. Treat the 0.39 as a guide only, since community readings vary with board state. | |||
PP5V_G3S_FAN_CONN | 0.39 | – | – |
AI: what PP5V_G3S_FAN_CONN is and how to check itPP5V_G3S_FAN_CONN is the fan connector's 5 V rail; the G3S in the name indicates it is an always-on rail (from the name, not from a schematic). The only known-good reading here is a diode value of 0.39 to ground; no known-good voltage reading is recorded. With the board unpowered, measure diode mode from the rail to ground and compare with 0.39; a much lower reading suggests a short or a leaky part on the rail, while a much higher one can mean an open trace or a missing connection. Then apply power and check the voltage at the connector, though without a known-good voltage you can only compare it with the rail's nominal 5 V and with a matching rail on a known-good board. A reading far from 0.39 is a guide to where to look next, not proof that a part is bad. | |||
PP5V_G3S_GFXIMVP_VDD | 0.409 | – | – |
AI: what PP5V_G3S_GFXIMVP_VDD is and how to check itPP5V_G3S_GFXIMVP_VDD — reference note
| |||
PP5V_G3S_GFXIMVP_VDDP | 0.408 | – | – |
AI: what PP5V_G3S_GFXIMVP_VDDP is and how to check it
| |||
PP5V_G3S_ISNS_D | OL | – | – |
AI: what PP5V_G3S_ISNS_D is and how to check itPP5V_G3S_ISNS_D is a 5 V always-on rail (G3S, from the name) with an ISNS current-sense suffix, so it's likely a sense line tied to that supply rather than a heavy load rail — that part is general interpretation, not from board data.
| |||
PP5V_G3S_TPAD_CONN | 0.39 | – | – |
AI: what PP5V_G3S_TPAD_CONN is and how to check itPP5V_G3S_TPAD_CONN is a 5 V rail feeding the trackpad connector, judged from the name; the G3S suffix indicates it is an always-on (G3H) rail. The only known-good reading in the archive is a diode value of 0.39 to ground, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the connector. A diode reading far below 0.39 suggests a short or leaky load on the rail, while a much higher one suggests an open trace or missing connection; confirm with a voltage check before replacing anything. | |||
PP5V_G3S_VCCIOVCC | 0.411 | – | – |
AI: what PP5V_G3S_VCCIOVCC is and how to check it
| |||
PPBUS_G3H | 0.434 | 12,600 | – |
PPBUS_G3H_R_IP0R | OL | – | – |
AI: what PPBUS_G3H_R_IP0R is and how to check itPPBUS_G3H_R_IP0R is the main battery-charging bus rail; the G3H part of the name indicates it is always-on, present whenever the charger is connected. The only archived reading here is a diode value of OL to ground, with no condition recorded and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then with the charger connected measure the voltage on it. A diode reading far below OL suggests a short or a leaky part on the rail, but with no second known-good value, compare against a matching rail on a known-good board before condemning anything. | |||
PPBUS_G3H_SSD0_SNS | 0.433 | 12,600 | – |
PPBUS_G3H_SSD1_SNS | OL | 12,600 | – |
PPDCIN_G3H | 0.540 | 20,000 | – |
AI: what PPDCIN_G3H is and how to check itPPDCIN_G3H is the always-on G3H input rail, as its name indicates — on this board it's the DC-in feed present whenever power is connected. The archive lists a known-good diode reading of 0.540 and a voltage of 20,000 (presumably mV, so about 20 V); treat these as a guide only, since community readings vary with board state. Check it unpowered in diode mode from the rail to ground, then apply power and measure the voltage on the rail. A diode reading far below 0.540 suggests a short or leaky load on the rail; a voltage well under 20 V points to a problem upstream in the DC-in path. No known-good resistance reading is available for this rail. | |||
PPDCIN_G3H_CHGR | 0.54 | 20,000 | – |
AI: what PPDCIN_G3H_CHGR is and how to check it
| |||
PPVBAT_G3H_CHGR_R | 0.434 | 12,600 | – |
AI: what PPVBAT_G3H_CHGR_R is and how to check itPPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name indicates an always-on rail, and CHGR points to the charger circuit (both from the name). Known-good readings here are a diode value of 0.434 and a voltage of 12,600 (units as recorded in the archive), so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good resistance reading exists here, so compare against a matching net or a known-good board. A diode value far below known-good usually points to a short or leaky part on the rail; confirm with voltage and resistance before replacing anything. | |||
PPVBAT_G3H_CHGR_REG | 0.434 | 12,600 | – |
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
| |||
PPVBAT_G3H_CONN | 1.40 | – | – |
AI: what PPVBAT_G3H_CONN is and how to check itPPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judging by the name (G3H = always on, CONN = connector). The only known-good figure here is a diode reading of 1.40 to ground; there is no known-good voltage or resistance reading for this rail.
A diode reading far from 1.40 usually points to a short or an open on that net rather than a fault elsewhere, but one reading alone doesn't confirm a bad part. These figures are community-contributed guides and vary with board state. | |||
PPVIN_G3H_P3V3G3HRTC_R | 0.436 | 3,300 | – |
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it
| |||
PPVIN_G3H_TPAD_FUSE | 0.434 | 12.600 | – |
AI: what PPVIN_G3H_TPAD_FUSE is and how to check itPPVIN_G3H_TPAD_FUSE is a trackpad power-input rail, and the G3H part of the name indicates it is always on. The archive lists a diode reading of 0.434 and a voltage of 12.600, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.434 usually points to a short or a leaky part on the rail, while a missing or low voltage with power applied points to an open fuse or an upstream supply fault; no known-good resistance reading exists here. | |||
S5 and SUS: standby 9
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_S5 | 0.35 | – | – |
AI: what PP1V8_S5 is and how to check itPP1V8_S5 is a 1.8 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the board fully powers on. The only known-good reading here is a diode value of 0.35 to ground, with no condition recorded; there is no known-good voltage reading in this data.
These are guides only, and a single reading doesn't confirm a bad part. | |||
PP1V8_S5_CPUTHMSNS_R | 0.377 | – | – |
AI: what PP1V8_S5_CPUTHMSNS_R is and how to check it
| |||
PP1V8_S5_GPIOX_R | 0.367 | – | – |
AI: what PP1V8_S5_GPIOX_R is and how to check itPP1V8_S5_GPIOX_R is a 1.8 V standby rail, judged from the name: "1V8" is the voltage and "S5" places it in the standby stage. The archive has one known-good diode reading for it, 0.367 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.367 suggests a short or a leaky part on that net, but a single reading isn't proof, so compare with a matching net or a known-good board before replacing anything. | |||
PP1V8_S5_GPUTHMSNS_R | OL | – | – |
AI: what PP1V8_S5_GPUTHMSNS_R is and how to check itPP1V8_S5_GPUTHMSNS_R is a 1.8 V standby rail, judged from its name (S5/SUS standby, likely a GPU thermal sensor supply). The only archived reading is a diode value of OL to ground, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in standby. An OL diode reading can be normal on a high-impedance sensor line, so compare against a matching rail or a known-good board before suspecting a fault. A voltage far from 1.8 V would point to the standby supply or an excessive load on the rail. | |||
PP1V8_S5_TBTTHMSNS_T_R | 0.414 | – | – |
AI: what PP1V8_S5_TBTTHMSNS_T_R is and how to check it
| |||
PP1V8_S5_TBTTHMSNS_X_R | 0.416 | – | – |
AI: what PP1V8_S5_TBTTHMSNS_X_R is and how to check it
| |||
PP3V3_S5 | 0.327 | – | – |
AI: what PP3V3_S5 is and how to check itPP3V3_S5 is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply, present before the board fully powers on. The archive lists one known-good diode reading of 0.327 to ground, with no condition noted. With the board unpowered, measure diode mode from PP3V3_S5 to ground and compare; then apply power and check the rail sits near 3.3 V. A diode reading far from 0.327 usually points to a short or a damaged component on that rail, but one reading isn't proof, so confirm before replacing anything. No known-good voltage reading is recorded here. | |||
PP3V3_S5_GPIOX_R | 0.328 | – | – |
AI: what PP3V3_S5_GPIOX_R is and how to check itPP3V3_S5_GPIOX_R is a 3.3 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, and the GPIOX suffix suggests it feeds a GPIO-related supply. The only known-good reading in the archive is a diode value of 0.328 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage reading is available here. A diode reading far from 0.328 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything. | |||
PP5V_S5_LDO | 0.481 | – | – |
AI: what PP5V_S5_LDO is and how to check itPP5V_S5_LDO is a 5V standby rail; the S5 and LDO in the name indicate it is a low-dropout supply in the standby domain (from the name). The archive lists one known-good diode reading of 0.481 to ground, with no condition noted and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.481, or a voltage that is missing or wrong, usually points to a fault on that rail or its load rather than proving a particular part is bad. | |||
S4 3
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V8_SSD1_S4E2_AVDD18_PLL | OL | – | – |
AI: what PP1V8_SSD1_S4E2_AVDD18_PLL is and how to check it
| |||
PP5V_S4_T_USBC | 0.215 | 5,000 | – |
AI: what PP5V_S4_T_USBC is and how to check it
| |||
PP5V_S4_X_USBC | 0.244 | 5,000 | 0.000R |
AI: what PP5V_S4_X_USBC is and how to check itPP5V_S4_X_USBC is a 5 V rail for the USB-C side, and its S4 name marks it as a startup-stage rail (both from the name). The archive lists a diode reading of 0.244 and a voltage of 5,000 for it; the resistance entry is 0.000R, which looks like a placeholder rather than a real known-good value, so treat resistance as having no known-good reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, comparing against those figures as a guide only. A voltage well below 5 V points to the rail not being enabled or its source failing; a diode reading far from 0.244 suggests a short or leak on the rail, but one reading alone doesn't confirm a bad part. | |||
S3: memory 6
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S3 | 0.163 | 1,200 | – |
AI: what PP1V2_S3 is and how to check itPP1V2_S3 is a 1.2 V rail; the S3 suffix, from its name, places it in the memory stage of startup. Known-good readings for this board: diode 0.163 to ground and 1,200 (1.2 V) with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.163 usually points to a short or a leaky load on the rail rather than the supply itself; a voltage well off 1.2 V points to the rail not coming up or being loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board. | |||
PP1V2_S3_CPUDDR | 0.161 | – | – |
AI: what PP1V2_S3_CPUDDR is and how to check itPP1V2_S3_CPUDDR is a 1.2 V rail feeding the CPU's DDR memory, judged from its name (S3 = memory stage). The archive lists a diode reading of 0.161 to ground for this net; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the rail. A diode value far from 0.161, or a voltage that is missing or well off 1.2 V, usually points to a short, an open feed, or a fault in the rail's supply — but one reading alone doesn't confirm a bad part, so compare against a known-good board where possible. | |||
PP1V2_S3_REG_R | 0,163 | 1,200 | 160.500 |
PP1V05_S3 | 0.214 | – | – |
AI: what PP1V05_S3 is and how to check itPP1V05_S3 is a 1.05 V supply rail in the S3 (memory) startup stage, judged from its name; the board data has no parts list for it. Known-good: diode 0.214 to ground (community reading, a guide only, no condition given). Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.214 usually points to a short or a leaky load on the rail, but confirm with a voltage check before replacing anything. | |||
PP2V5_S3 | 0.360 | 2,500 | – |
AI: what PP2V5_S3 is and how to check itPP2V5_S3 is a 2.5 V rail; the S3 suffix in its name places it in the memory stage of startup. Known-good readings here are diode 0.360 to ground and 2,500 mV with power applied. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A reading far from known-good usually points to a short or a rail that isn't coming up, but one reading alone doesn't confirm a bad part; no known-good resistance value is listed for this rail. | |||
PPVIN_S3_DDR2V5_RC | 0.442 | – | – |
AI: what PPVIN_S3_DDR2V5_RC is and how to check it
| |||
S0: running 37
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP0V6_S0_DDRVTT | 0.126 | – | – |
AI: what PP0V6_S0_DDRVTT is and how to check itPP0V6_S0_DDRVTT is a 0.6 V DDR termination rail; the 0V6 and DDRVTT come from the name, and S0 means it's present in the running state. The only known-good reading here is diode 0.126 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, comparing against a matching net or a known-good board since no voltage value is listed. A diode reading far from 0.126 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part. | |||
PP0V95_S0_CPUVCCIO_REG_R | 0.076 | – | 75.600R |
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check itPP0V95_S0_CPUVCCIO_REG_R — reference note
| |||
PP1V2_S0SW | 0.324 | – | – |
AI: what PP1V2_S0SW is and how to check itPP1V2_S0SW is a 1.2 V rail; the S0 in its name indicates it belongs to the running (S0) state, and SW suggests it is a switched rail. The archive lists one known-good diode reading of 0.324 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.324 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything. | |||
PP1V05_S0SW | 0.216 | – | – |
AI: what PP1V05_S0SW is and how to check itPP1V05_S0SW is a 1.05 V rail that, from its name, is a switched S0 (running-state) supply. The only known-good figure here is a diode reading of 0.216 to ground; there is no known-good voltage reading for this rail.
| |||
PP1V5R1V35_S0_GPU_IC | 0.053 | 1,350 | 52.600R |
AI: what PP1V5R1V35_S0_GPU_IC is and how to check itPP1V5R1V35_S0_GPU_IC — reference note
| |||
PP1V5R1V35_S0_GPU_MEM | 0.053 | 1,350 | 52.800R |
AI: what PP1V5R1V35_S0_GPU_MEM is and how to check itPP1V5R1V35_S0_GPU_MEM — 820-01814
| |||
PP1V8_S0_GPU | 0.277 | – | 280.000R |
AI: what PP1V8_S0_GPU is and how to check it
| |||
PP1V8_S0_GPU_LC_IC | 0.277 | – | – |
AI: what PP1V8_S0_GPU_LC_IC is and how to check itPP1V8_S0_GPU_LC_IC is a 1.8 V supply rail for the GPU, and the S0 in its name indicates it belongs to the running (S0) power state. The only known-good reading here is a diode value of 0.277 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.277 usually points to a short or a damaged component on that rail, but a small difference can be normal, so compare against a matching rail before condemning anything. | |||
PP1V8_S0_PCH_VCCHDA_F | 0.350 | – | – |
AI: what PP1V8_S0_PCH_VCCHDA_F is and how to check itPP1V8_S0_PCH_VCCHDA_F is a 1.8 V rail; from its name it feeds the PCH's HDA (high-definition audio) supply and is active in the S0 running state. The only known-good reading here is a diode value of 0.350 to ground, with no condition stated; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far from 0.350 usually points to a short or a leaky part on that rail, but one reading alone doesn't prove a part bad, so compare against a matching rail or a known-good board before replacing anything. | |||
PP3V3_S0_GPU | 0.453 | – | – |
AI: what PP3V3_S0_GPU is and how to check itPP3V3_S0_GPU is a 3.3 V rail for the GPU that is up in the S0 (running) state, judging from its name. The archive lists a known-good diode reading of 0.453 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far from 0.453 suggests a short or a damaged part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board. | |||
PP3V3_S0SW_LCD | 0.490 | – | – |
AI: what PP3V3_S0SW_LCD is and how to check itPP3V3_S0SW_LCD is a switched 3.3 V LCD rail; the S0 in the name indicates it belongs to the running state, and SW suggests it is switched on rather than always present (both from the name). The only known-good figure here is a diode reading of 0.490 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.490 usually points to a short or a faulty component on the rail, but confirm with a voltage measurement before replacing anything. | |||
PP3V3_S0SW_LCD_R | 0.553 | – | – |
AI: what PP3V3_S0SW_LCD_R is and how to check itPP3V3_S0SW_LCD_R is a 3.3 V LCD-related rail that is switched and, from its name, active in the S0 running state. The only known-good reading here is a diode value of 0.553 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.553 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PP3V3_S0SW_TBT_T | 0.535 | – | – |
AI: what PP3V3_S0SW_TBT_T is and how to check itPP3V3_S0SW_TBT_T is a 3.3 V rail that is switched on in the S0 (running) state, judging by its name; the TBT suffix points to the Thunderbolt side of the board. The only known-good figure here is a diode reading of 0.535 to ground, with no condition noted, so treat it as a guide. Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare. Then apply power and measure the voltage, which should sit near 3.3 V once the board is in S0. There is no known-good voltage reading for this rail in the data. A diode reading far below 0.535 suggests a short or a leaky part on the rail; far above it suggests an open connection. Confirm with voltage and resistance before replacing anything. | |||
PP3V3_S0SW_TBT_T_SNS | 0.535 | 3,300 | – |
AI: what PP3V3_S0SW_TBT_T_SNS is and how to check it
| |||
PP3V3_S0SW_TBT_X | 0.535 | – | – |
AI: what PP3V3_S0SW_TBT_X is and how to check itPP3V3_S0SW_TBT_X is a switched 3.3 V rail for the Thunderbolt section, in the S0 (running) state, judging from its name. The archive lists one known-good diode reading of 0.535 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.535 suggests a short or a leaky part on the rail; a much higher or open reading points to a broken connection. This is a guide only, and one reading doesn't confirm a bad part. | |||
PP3V3_S0SW_TBT_X_SNS | 0.537 | 3,300 | – |
AI: what PP3V3_S0SW_TBT_X_SNS is and how to check it
| |||
PP5V_S0_ALSCAM_F | 0.386 | – | – |
AI: what PP5V_S0_ALSCAM_F is and how to check itPP5V_S0_ALSCAM_F is a 5 V rail that, from its name, belongs to the camera supply and is active in the S0 (running) state. The only known-good reading here is a diode value of 0.386 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.386 usually points to a short or a leaky part on that rail, but a single reading doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything. | |||
PP5V_S0_GPUFET | 0.567 | – | – |
AI: what PP5V_S0_GPUFET is and how to check it
| |||
PP5V_S0_PCCAMP | OL | – | – |
AI: what PP5V_S0_PCCAMP is and how to check itPP5V_S0_PCCAMP is a 5 V rail for the camera section, and the S0 in its name indicates it belongs to the running (S0) state. The only archived reading is a diode value of OL to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP5V_S0_PCCAMP to ground and compare with that OL figure, then apply power and check the voltage. A diode reading far below OL usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault. | |||
PP5V_S0GPU_P1V35_GPU | 0.408 | – | – |
AI: what PP5V_S0GPU_P1V35_GPU is and how to check it
| |||
PP5V_S0SW_LCD | 0.566 | – | – |
AI: what PP5V_S0SW_LCD is and how to check itPP5V_S0SW_LCD is a 5 V LCD-related rail; from its name it is an S0 (running-state) switched supply for the display section. The only known-good reading here is a diode value of 0.566 to ground, with the board unpowered. Check it in diode mode from the rail to ground with power off, then measure the voltage with the board powered and the display active. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.566 usually points to a short or leaky part on the rail; a much higher or open reading points to a broken connection — confirm with more measurements before replacing anything. | |||
PPVCC_S0_CPU | 0.002 | 1,500 | 2,100R |
AI: what PPVCC_S0_CPU is and how to check itPPVCC_S0_CPU — 820-01814 reference note
| |||
PPVCCGT_S0_CPU | 0.006 | 1,500 | 5,600R |
AI: what PPVCCGT_S0_CPU is and how to check it
| |||
PPVCCIO_S0_CPU | 0.076 | – | – |
AI: what PPVCCIO_S0_CPU is and how to check itPPVCCIO_S0_CPU is the CPU's S0 (running-state) I/O supply rail; the S0 and CPU parts come from the rail name, and it's a low-voltage rail. The only known-good figure in the readings archive is a diode reading of 0.076 to ground, with no condition recorded. Check it with the board unpowered in diode mode, probe to ground, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare the powered voltage against a matching rail or a known-good board. A diode reading far from 0.076 usually points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault. | |||
PPVCCSA_S0_CPU | 0.022 | 1,150 | 22,200R |
PPVCORE_S0_GFX_PH1 | 0.002 | – | 2.100R |
AI: what PPVCORE_S0_GFX_PH1 is and how to check itPPVCORE_S0_GFX_PH1 is a graphics core power rail; the S0 in the name indicates it is a running-state rail, and PH1 suggests one phase of a multiphase supply (both from the name, general convention).
| |||
PPVCORE_S0_GFX_PH2 | 0.002 | 1,100 | 2.100R |
PPVCORE_S0_GFX_PH3 | 0.002 | 1,100 | 2.100R |
AI: what PPVCORE_S0_GFX_PH3 is and how to check itPPVCORE_S0_GFX_PH3 — reference note
| |||
PPVCORE_S0_GPU | 0,002 | 1,100 | 2.100R |
PPVDDCI_S0_GPU | 0.035 | 0,900 | 34.400R |
PPVIN_S0_CPUVR_VIN | 0.438 | – | – |
AI: what PPVIN_S0_CPUVR_VIN is and how to check itPPVIN_S0_CPUVR_VIN is the CPU VRM input rail, from its name: the supply feeding the CPU voltage regulator, active in the S0 (running) state. The archive lists one known-good reading: diode 0.438, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.438 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part. | |||
PPVIN_S0_GFXIMVP_VIN | 0.433 | – | – |
AI: what PPVIN_S0_GFXIMVP_VIN is and how to check it
| |||
PPVIN_S0GPU_1V8_RC | 0.443 | – | – |
AI: what PPVIN_S0GPU_1V8_RC is and how to check it
| |||
PPVIN_S0SW_LCDBKLT | 0.870 | 12,600 | 0.549R |
PPVIN_S0SW_LCDBKLT_FET | 0.434 | 12,600 | – |
PPVIN_S0SW_LCDBKLT_R | 0.434 | 12,600 | – |
PPVOUT_S0_LCDBKLT | 1.142 | 59,000 | – |
AI: what PPVOUT_S0_LCDBKLT is and how to check itPPVOUT_S0_LCDBKLT is the LCD backlight output rail; the S0 in the name indicates it belongs to the running (S0) power state, and the VOUT/BKLT parts indicate a backlight converter output. In the readings archive the only known-good values are a diode reading of 1.142 and a voltage of 59,000 (units as recorded; treat both as a guide, since community readings vary with board state). Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far below 1.142 usually points to a short or leaky load on the backlight output, while a voltage far from the recorded value points to the backlight supply or its feedback/enable path rather than the rail itself. There is no known-good resistance reading for this rail, so compare against a matching net or a known-good board. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
5VG3S_VFB1_RR | 0.609 | – | – |
50_0_ANT | 0.001 | – | – |
50_1_ANT | 0.001 | – | – |
50_2_ANT | 0.001 | – | – |
ACT_GND | 0.00 | – | – |
ADC1_REFCOMP | OL | – | – |
ADC2_REFCOMP | OL | – | – |
AGND_P1V8GPU | 0.000 | – | – |
AGND_P2V5S3 | 0.000 | – | – |
ALL_SYS_PWRGD | 0.519 | – | – |
ALL_SYS_PWRGD_R | 0.461 | – | – |
AON_SLEEP1_RESET_L | 0.435 | – | – |
AP_PCIE_WAKE_L | 0.533 | – | – |
AUD_CONN_HP_LEFT | 0.57 | – | – |
AUD_CONN_HP_RIGHT | 0.57 | – | – |
AUD_CONN_HP_SENSE_L | 1.12 | – | – |
AUD_CONN_HP_SENSE_R | 1.12 | – | – |
AUD_CONN_RING_SENSE | 2.29 | – | – |
AUD_CONN_RING2 | 0.00 | – | – |
AUD_CONN_RING2_XW | 0.61 | – | – |
AUD_CONN_SLEEVE | 0.00 | – | – |
AUD_CONN_SLEEVE_XW | 0.61 | – | – |
AUD_CONN_TIP_SENSE | OL | – | – |
AUD_DMIC0_CLK_CONN | 0.518 | – | – |
AUD_DMIC0_DATA_CONN | 0.52 | – | – |
AUD_DMIC1_CLK_CONN | 0.47 | – | – |
AUD_DMIC1_DATA_CONN | 0.52 | – | – |
AUD_HP_PORT_CH_GND | 0.000 | – | – |
AUD_HP_PORT_L | 0.703 | – | – |
AUD_HP_PORT_R | 0.703 | – | – |
AUD_HS_MIC_N | 0.628 | – | – |
AUD_HS_MIC_P | 0.628 | – | – |
AUD_PWR_EN | 0.776 | – | – |
AUD_RING_SENSE | 0.642 | – | – |
AUD_TIP_SENSE | 1.484 | – | – |
BKLT_EN_R | 0.526 | – | – |
BKLT_PWM_KEYB | 0.542 | – | – |
BKLT_SCL | 0.537 | – | – |
BKLT_SD | 0.587 | – | – |
BKLT_SDA | 0.536 | – | – |
BKLT_SENSE_OUT | 0.737 | – | – |
BT_GPIO_3 | 0.758 | – | – |
BT_GPIO_4 | 0.730 | – | – |
BT_HOST_WAKE | 0.488 | – | – |
BT_PWR_EN | 0.490 | – | – |
BT_ROM_BOOT_HPN_L | 0.586 | – | – |
BT_ROM_BOOT_L | 0.480 | – | – |
BT_SFLASH_CS_L | 0.702 | – | – |
BT_SFLASH_HOLD_L | 0.711 | – | – |
BT_SFLASH_WP_L | 0.710 | – | – |
BT_SPI2_CLK | 0.686 | – | – |
BT_SPI2_CLK_R | 0.639 | – | – |
BT_SPI2_CSN_R | 0.599 | – | – |
BT_SPI2_MISO | 0.689 | – | – |
BT_SPI2_MISO_R | OL | – | – |
BT_SPI2_MOSI | 0.685 | – | – |
BT_SPI2_MOSI_R | OL | – | – |
BTUARTMUX_OE_L | 0.487 | – | – |
BTUARTMUX_SEL_PCH | 0.477 | – | – |
CHGR_AUX_DET | 0.635 | – | – |
CHGR_BGATE | 0.636 | – | – |
CHGR_BMON | 0.629 | – | – |
CHGR_BOOT1 | 0.58 | – | – |
CHGR_BOOT1_RC | 0.597 | – | – |
CHGR_BOOT2 | 0.57 | – | – |
CHGR_BOOT2_RC | 0.596 | – | – |
CHGR_COMP | 0.61 | – | – |
CHGR_CSI_N | 0.54 | 20,000 | – |
CHGR_CSI_P | 0.54 | 20,000 | – |
CHGR_CSI_R_N | 0.540 | 20,000 | – |
CHGR_CSI_R_P | 0.540 | 20,000 | – |
CHGR_CSO_BMON_R_N | OL | – | – |
CHGR_CSO_BMON_R_P | OL | – | – |
CHGR_CSO_BMON_VREG | OL | – | – |
CHGR_CSO_N | 0.409 | 12,600 | – |
CHGR_CSO_P | 0.409 | 12,600 | – |
CHGR_CSO_R_N | 0.409 | 12,600 | – |
CHGR_CSO_R_P | 0.409 | 12,600 | – |
CHGR_EN_MVR | 0.612 | – | – |
CHGR_EN_MVR_R | 0.59 | – | – |
CHGR_GATE_Q1 | 0.944 | – | – |
CHGR_GATE_Q2 | 0.470 | – | – |
CHGR_GATE_Q3 | 0.471 | – | – |
CHGR_GATE_Q4 | 0.720 | – | – |
CHGR_INT_L | 0.614 | – | – |
CHGR_LX1 | 0.47 | – | – |
CHGR_LX2 | 0.47 | – | – |
CHGR_PHASE1 | 0.466 | 12,600 | 223.800 |
CHGR_PHASE2 | 0.466 | 12,600 | 223.800 |
CHGR_RST_IN | 0.61 | – | – |
CHGR_RST_IN_R | OL | – | – |
CHGR_VBAT | 0.62 | – | – |
CHGR_VDDA | 0.44 | – | – |
CHGR_VDDP | 0.44 | – | – |
CODEC_INT_L | 0.493 | – | – |
CODEC_RESET_L | 0.495 | – | – |
CODEC_WAKE_L | 0.493 | – | – |
COMP_A_CPUCORE | 0.625 | – | – |
COMP_A_CPUCORE_L | OL | – | – |
COMP_B_CPUGT | 0.624 | – | – |
COMP_B_CPUGT_L | 0.630 | – | – |
COMP_C_CPUSA | 0.624 | – | – |
COMP_C_CPUSA_L | 1.967 | – | – |
CORE_ISUMN_R | 1.007 | – | – |
CPU_C10_GATE_L | 0.512 | – | – |
CPU_CATERR_L | 0.228 | – | – |
CPU_CFG_RCOMP | 0.051 | – | 50.100R |
CPU_CFG<0> | 0.284 | – | – |
CPU_CFG<1> | 0.284 | – | – |
CPU_CFG<2> | 0.284 | – | – |
CPU_CFG<3> | 0.284 | – | – |
CPU_CFG<4> | 0.269 | – | – |
CPU_CFG<5> | 0.268 | – | – |
CPU_CFG<6> | 0.270 | – | – |
CPU_CFG<7> | 0.285 | – | – |
CPU_CFG<8> | 0.282 | – | – |
CPU_CFG<9> | 0.283 | – | – |
CPU_CFG<10> | 0.283 | – | – |
CPU_CFG<11> | 0.285 | – | – |
CPU_CFG<12> | 0.284 | – | – |
CPU_CFG<13> | 0.285 | – | – |
CPU_CFG<14> | 0.284 | – | – |
CPU_CFG<15> | 0.285 | – | – |
CPU_CFG<16> | 0.287 | – | – |
CPU_CFG<17> | 0.287 | – | – |
CPU_CFG<18> | 0.286 | – | – |
CPU_CFG<19> | 0.286 | – | – |
CPU_DC_B2_C1 | OL | – | – |
CPU_DC_B38_C38 | OL | – | – |
CPU_DC_BR1_BR2 | 0.341 | – | – |
CPU_DC_BR2_BR1 | OL | – | – |
CPU_DC_C1_B2 | OL | – | – |
CPU_DC_C38_B38 | OL | – | – |
CPU_EDP_RCOMP | 0.095 | – | – |
CPU_IST_TRIG | 0.335 | – | – |
CPU_PCH_PM_DOWN | 0.300 | – | – |
CPU_PCH_PM_DOWN_R | 0.283 | – | – |
CPU_PCH_TRIGGER_R | 0.280 | – | – |
CPU_PECI | 0.403 | – | – |
CPU_PROCHOT_L | 0.473 | – | – |
CPU_PROCHOT_OUT_L | 0.489 | – | – |
CPU_PROCHOT_R_L | 0.277 | – | – |
CPU_PWRGD | 0.366 | – | – |
CPU_RESET_L | 0.370 | – | – |
CPU_RSVD_AA14 | 0.007 | – | 7.200R |
CPU_RSVD_AE29 | 0.007 | – | 6.400R |
CPU_RSVD_N29 | 0.007 | – | 6.400R |
CPU_RSVD_R14 | 0.007 | – | 7.000R |
CPU_SMC_THRMTRIP_L | 0.487 | – | – |
CPU_VCCGTSENSE_N | 0.003 | – | 2.800R |
CPU_VCCGTSENSE_P | 0.008 | – | 7.700R |
CPU_VCCIOSENSE_N | 0.000 | – | – |
CPU_VCCIOSENSE_P | 0.087 | – | – |
CPU_VCCIOSENSENEG_R | 0.006 | – | – |
CPU_VCCIOSENSEPOS_R | 0.156 | – | – |
CPU_VCCSASENSE_N | 0.004 | – | 3.300R |
CPU_VCCSASENSE_P | 0.026 | – | 25.500R |
CPU_VCCSENSE_N | 0.004 | – | 3.300R |
CPU_VCCSENSE_P | 0.005 | – | 4.700R |
CPU_VCCST_PWRGD | 0.535 | – | – |
CPU_VIDALERT_L | 0.272 | – | – |
CPU_VIDALERT_R_L | 0.493 | – | – |
CPU_VIDSCLK | 0.226 | – | – |
CPU_VIDSCLK_R | 0.226 | – | – |
CPU_VIDSOUT | 0.225 | – | 0.000R |
CPU_VIDSOUT_R | 0.226 | – | – |
CPU_VR_EN_R | 0.559 | – | – |
CPUCORE_BOOT1 | 0.609 | – | – |
CPUCORE_BOOT2 | 0.610 | – | – |
CPUCORE_BOOT3 | 0.607 | – | – |
CPUCORE_BP1 | 0.610 | – | – |
CPUCORE_BP2 | 0.607 | – | – |
CPUCORE_BP3 | 0.607 | – | – |
CPUCORE_FCCM | 0.598 | – | – |
CPUCORE_ISEN1 | 0.625 | – | – |
CPUCORE_ISEN2 | 0.626 | – | – |
CPUCORE_ISEN3 | 0.626 | – | – |
CPUCORE_ISNS1_N | 0.002 | 1,500 | 2.100R |
CPUCORE_ISNS1_P | 0,002 | 1,500 | 2.100R |
CPUCORE_ISNS2_N | 0.002 | 1,500 | 2,100R |
CPUCORE_ISNS2_P | 0.002 | 1,500 | 2,100R |
CPUCORE_ISNS3_N | 0.002 | 1,500 | 2,100R |
CPUCORE_ISNS3_P | 0.002 | 1,500 | 2,100R |
CPUCORE_ISUMN | 0.003 | – | 2.800R |
CPUCORE_ISUMN_R | 0.471 | – | – |
CPUCORE_ISUMP | 0.382 | – | – |
CPUCORE_PHASE1 | 0.000 | – | – |
CPUCORE_PHASE2 | 0.000 | – | – |
CPUCORE_PHASE3 | 0.000 | – | – |
CPUCORE_PROCHOT_R_L | 0.525 | – | – |
CPUCORE_PSYS | 0.623 | – | – |
CPUCORE_PWM1 | 0.611 | – | – |
CPUCORE_PWM2 | 0.611 | – | – |
CPUCORE_PWM3 | 0.611 | – | – |
CPUCORE_SW1 | 0.002 | 1,500 | 2.100R |
CPUCORE_SW1_SNUB | OL | – | – |
CPUCORE_SW2 | 0.002 | 1,500 | 2.100R |
CPUCORE_SW2_SNUB | OL | – | – |
CPUCORE_SW3 | 0.002 | 1,500 | 2.100R |
CPUCORE_SW3_SNUB | OL | – | – |
CPUCORE_VIDALERT_R_L | 0.284 | – | – |
CPUCORE_VIDSCLK_R | 0.290 | – | – |
CPUCORE_VIDSOUT_R | 0.245 | – | – |
CPUGT_BOOT1 | 0.610 | – | – |
CPUGT_BOOT2 | 0.609 | – | – |
CPUGT_BP1 | 0.610 | – | – |
CPUGT_BP2 | 0.609 | – | – |
CPUGT_FCCM | 0.605 | – | – |
CPUGT_ISEN1 | 0.626 | – | – |
CPUGT_ISEN2 | 0.627 | – | – |
CPUGT_ISNS_N | OL | – | – |
CPUGT_ISNS_P | OL | – | – |
CPUGT_ISNS_R_N | OL | – | – |
CPUGT_ISNS_R_P | OL | – | – |
CPUGT_ISNS1_N | 0.006 | 1,500 | 5,600R |
CPUGT_ISNS1_P | 0.006 | 1,500 | 5,600R |
CPUGT_ISNS2_N | 0.006 | 1,500 | 5,600R |
CPUGT_ISNS2_P | 0.006 | 1,500 | 5,600R |
CPUGT_ISUM_IOUT | OL | – | – |
CPUGT_ISUMN | 0.007 | – | 6.400R |
CPUGT_ISUMN_R | 0.384 | – | – |
CPUGT_ISUMP | 0.503 | – | – |
CPUGT_PHASE1 | 0.000 | – | – |
CPUGT_PHASE2 | 0.000 | – | – |
CPUGT_PWM1 | 0.611 | – | – |
CPUGT_PWM2 | 0.611 | – | – |
CPUGT_SW1 | 0.006 | 1,500 | 5.600R |
CPUGT_SW1_SNUB | OL | – | – |
CPUGT_SW2 | 0.006 | 1,500 | 5,600R |
CPUGT_SW2_SNUB | OL | – | – |
CPUSA_BOOTSA | 0.408 | – | – |
CPUSA_BPSA | 0.620 | – | – |
CPUSA_FCCM | 0.540 | – | – |
CPUSA_ISNS_N | 0.022 | 1,150 | 22,200R |
CPUSA_ISNS_P | 0.022 | 1,150 | 22,200R |
CPUSA_ISUMN | 0.025 | – | 24.500R |
CPUSA_ISUMN_R | 0.503 | – | – |
CPUSA_ISUMP | 0.577 | – | – |
CPUSA_PHASESA | 0.023 | – | – |
CPUSA_PWM | 0.625 | – | – |
CPUSA_SW_SNUB | OL | – | – |
CPUSAVSENSE_IN | 0.025 | – | 23.200R |
CPUTHMSNS_ADD | 0.639 | – | – |
CPUVR_ISNS_N | OL | – | – |
CPUVR_ISNS_P | OL | – | – |
CPUVR_ISNS_R_N | OL | – | – |
CPUVR_ISNS_R_P | OL | – | – |
CPUVR_ISUM_IOUT | OL | – | – |
CPUVR_PGOOD | 0.571 | – | – |
CPUVR_SWSA | 0.022 | 1,150 | 22.200R |
CPUVSENSE_IN | 0.000 | – | – |
DBGLED_C10 | OL | – | – |
DBGLED_GPU | OL | – | – |
DBGLED_GPU_D | OL | – | – |
DBGLED_S0I3 | OL | – | – |
DBGLED_S0I3_D | OL | – | – |
DBGLED_S5 | OL | – | – |
DDR2V5_IOUT | OL | – | – |
DDRREG_VTTSNS | 0.126 | – | – |
DEBUG_CLKREQ_L | 0.825 | – | – |
DEBUG_JTAG_SOC_TDI | 0.495 | – | – |
DEBUG_JTAG_SOC_TDO | 0.493 | – | – |
DFR_DISP_INT | 0.46 | – | – |
DFR_DISP_RESET_L | 0.46 | – | – |
DFR_DISP_TE | 0.46 | – | – |
DFR_DISP_VSYNC | OL | – | – |
DFR_LID_OPEN_L | OL | – | – |
DFR_PWR_EN | 0.45 | – | – |
DFR_PWR_EN_R | 0.552 | – | – |
DFR_TOUCH_CLK32K_RESET_L | 0.46 | – | – |
DFR_TOUCH_INT_L | 0.45 | – | – |
DFR_TOUCH_RESET_L | 0.46 | – | – |
DISP_GCON_INT_L | 0.493 | – | – |
DISP_GCON_RESET_L | 0.680 | – | – |
DISP_GCON_RESET_L_R | 0.679 | – | – |
DP_INT_EG_HPD | 0.427 | – | – |
DP_INT_EG_HPD_R | 0.730 | – | – |
DP_INT_HPD | 0.700 | – | – |
DP_INT_HPD_R | 0.607 | – | – |
DP_INT_IG_HPD | 0.611 | – | – |
DP_INT_IG_HPD_R | 0.731 | – | – |
DP_T_SNK0_HPD | 0.590 | – | – |
DP_T_SNK0_HPD_EG | 0.412 | – | – |
DP_T_SNK1_HPD | 0.590 | – | – |
DP_T_SNK1_HPD_EG | 0.412 | – | – |
DP_TA_HPD | 0.595 | – | – |
DP_TB_HPD | 0.596 | – | – |
DP_X_SNK0_HPD | 0.555 | – | – |
DP_X_SNK0_HPD_EG | 0.414 | – | – |
DP_X_SNK1_HPD | 0.589 | – | – |
DP_X_SNK1_HPD_EG | 0.413 | – | – |
DP_XA_HPD | 0.595 | – | – |
DP_XB_HPD | 0.597 | – | – |
EADC1_CPUGT_ISENSE | OL | – | – |
EADC1_CPUGT_VSENSE | OL | – | – |
EADC1_CPUSA_ISENSE | OL | – | – |
EADC1_CPUSA_VSENSE | OL | – | – |
EADC1_LCDBKLT_ISENSE | OL | – | – |
EADC1_LCDPANEL_ISENSE | OL | – | – |
EADC1_TBT_X_ISENSE | OL | – | – |
EADC1_VCCIO_ISENSE | OL | – | – |
EADC2_DDR2V5_ISENSE | OL | – | – |
EADC2_GPU_1V8_ISENSE | OL | – | – |
EADC2_GPU_FBIC_ISENSE | OL | – | – |
EADC2_GPU_VDDCI_VSENSE | OL | – | – |
EADC2_PCH_1V0_ISENSE | OL | – | – |
EADC2_PP3V3S5_T139_ISENSE | OL | – | – |
EADC2_TBT_T_ISENSE | OL | – | – |
EDP_BKLT_EN | 0.526 | – | – |
EDP_INT_AUX_N | 0.400 | – | – |
EDP_INT_AUX_P | 0.400 | – | – |
EDP_INT_ML_N<0> | 0.390 | – | – |
EDP_INT_ML_N<1> | 0.390 | – | – |
EDP_INT_ML_N<2> | 0.390 | – | – |
EDP_INT_ML_N<3> | 0.390 | – | – |
EDP_INT_ML_P<0> | 0.390 | – | – |
EDP_INT_ML_P<1> | 0.390 | – | – |
EDP_INT_ML_P<2> | 0.390 | – | – |
EDP_INT_ML_P<3> | 0.390 | – | – |
EDP_MUXSEL_OVR | 0.612 | – | – |
EDP_PANEL_PWR_BUF_EN | 0.700 | – | – |
EDP_PANEL_PWR_DLY_EN | 0.709 | – | – |
EDP_PANEL_PWR_EN | 0.541 | – | – |
EG_BKLT_EN | 0.413 | – | – |
EG_LCD_PWR_EN | 0.411 | – | – |
EG_RESET_L_BUFF | 0.514 | – | – |
EG_VR0_EN | 0.523 | – | – |
EG_VR0_PGOOD | 0.513 | – | – |
EG_VR1_EN | 0.618 | – | – |
EG_VR2_EN | 0.620 | – | – |
EG_VR3_EN | 0.574 | – | – |
EG_VR4_EN | 0.537 | – | – |
ESPI_CLK60M | 0.488 | – | – |
ESPI_CLK60M_DBG | OL | – | – |
ESPI_CLK60M_PCH | 0.490 | – | – |
ESPI_CLK60M_PCH_R | 0.507 | – | – |
ESPI_IO_PCH<0> | 0.532 | – | – |
ESPI_IO_PCH<1> | 0.533 | – | – |
ESPI_IO_PCH<2> | 0.535 | – | – |
ESPI_IO_PCH<3> | 0.539 | – | – |
ESPI_IO<0> | 0.511 | – | – |
ESPI_IO<1> | 0.520 | – | – |
ESPI_IO<2> | 0.513 | – | – |
ESPI_IO<3> | 0.513 | – | – |
ESPI_RESET_L | 0.491 | – | – |
FAN_LT_PWM | 0.77 | – | – |
FAN_LT_TACH | OL | 1.800 | – |
FAN_RT_PWM | 0.82 | – | – |
FAN_RT_TACH | OL | 1.800 | – |
FB_A_CALR | 0.463 | – | – |
FB_A_CORE_R | 1.625 | – | – |
FB_A_CPUCORE | 0.615 | – | – |
FB_A_CPUCORE_RC | 1.184 | – | – |
FB_A_MVREFD | 0.608 | – | – |
FB_A_RESET_L | 0.471 | – | – |
FB_A0_CLK_N | 0.116 | – | – |
FB_A0_CLK_P | 0.116 | – | – |
FB_A0_MF | 0.121 | – | – |
FB_A0_SEN | 0.121 | – | – |
FB_A0_VREFC | 0.311 | – | – |
FB_A0_VREFD | 0.582 | – | – |
FB_A0_ZQ | 0.121 | – | – |
FB_A0_ZQ1 | OL | – | – |
FB_A1_MF | 0.121 | – | – |
FB_A1_SEN | 0.120 | – | – |
FB_A1_VREFC | 0.313 | – | – |
FB_A1_VREFD | 0.590 | – | – |
FB_A1_ZQ | 0.121 | – | – |
FB_A1_ZQ1 | OL | – | – |
FB_B_CALR | 0.460 | – | – |
FB_B_CPUGT | 0.597 | – | – |
FB_B_CPUGT_RC | 1.169 | – | – |
FB_B_GT_R | OL | – | – |
FB_B_MVREFD | 0.688 | – | – |
FB_B_RESET_L | 0.471 | – | – |
FB_B_RESET_PIN_L | 0.432 | – | – |
FB_B_RESET_R_L | 0.440 | – | – |
FB_B0_CLK_N | 0.115 | – | – |
FB_B0_CLK_P | 0.115 | – | – |
FB_B0_MF | 0.121 | – | – |
FB_B0_SEN | 0.121 | – | – |
FB_B0_VREFC | 0.312 | – | – |
FB_B0_VREFD | 0.587 | – | – |
FB_B0_ZQ | 0.121 | – | – |
FB_B0_ZQ1 | OL | – | – |
FB_B1_CLK_N | 0.116 | – | – |
FB_B1_CLK_P | 0.116 | – | – |
FB_B1_MF | 0.121 | – | – |
FB_B1_SEN | 0.121 | – | – |
FB_B1_VREFC | 0.311 | – | – |
FB_B1_VREFD | 0.588 | – | – |
FB_B1_ZQ | 0.121 | – | – |
FB_B1_ZQ1 | OL | – | – |
FB_C_CPUSA | 0.606 | – | – |
FB_C_CPUSA_RC | 1.074 | – | – |
FB_C_SA_R | 1.616 | – | – |
FB_CORE_R | – | – | 4.700R |
FB_GT_R | 0.008 | – | 7.800R |
FB_SA_R | 0.025 | – | 25.000R |
FB_SW_LEG | 0.363 | – | – |
FBVDD_ALTVO | 0.558 | – | – |
GFX_SELF_THROTTLE | 0.406 | – | – |
GFX_SELF_THROTTLE_1V8 | 0.473 | – | – |
GFX_THROTTLE_1V8_L | 0.490 | – | – |
GFX_THROTTLE_1V8_R_L | 0.706 | – | – |
GFX_THROTTLE_L | 0.413 | – | – |
GFXIMVP_BOOT | 0.609 | – | – |
GFXIMVP_BOOT_R | 0.609 | – | – |
GFXIMVP_BOOT1 | 0.483 | – | – |
GFXIMVP_BOOT1_R | 0.483 | – | – |
GFXIMVP_BOOT2 | 0.483 | – | – |
GFXIMVP_BOOT2_R | 0.483 | – | – |
GFXIMVP_FCCM | 0.407 | – | – |
GFXIMVP_ISEN1 | 0.622 | – | – |
GFXIMVP_ISEN2 | 0.622 | – | – |
GFXIMVP_ISEN3 | 0.622 | – | – |
GFXIMVP_ISNS_N | OL | – | – |
GFXIMVP_ISNS_P | OL | – | – |
GFXIMVP_ISNS_R_N | OL | – | – |
GFXIMVP_ISNS_R_P | OL | – | – |
GFXIMVP_ISNS1_N | 0.002 | – | – |
GFXIMVP_ISNS1_P | 0.002 | – | – |
GFXIMVP_ISNS2_N | 0.002 | 1,100 | 2.100R |
GFXIMVP_ISNS2_P | 0.002 | 1,100 | 2.100R |
GFXIMVP_ISNS3_N | 0,002 | 1,100 | 2.100R |
GFXIMVP_ISNS3_P | 0,002 | 1,100 | 2.100R |
GFXIMVP_ISUMN | 0.000 | – | – |
GFXIMVP_ISUMN_R | 0.512 | – | – |
GFXIMVP_ISUMP | 0.337 | – | – |
GFXIMVP_ISUMP_C | OL | – | – |
GFXIMVP_LGATE1 | 0.471 | – | – |
GFXIMVP_LGATE3 | 0.431 | – | – |
GFXIMVP_PHASE1 | 0.002 | 1,100 | 2.100R |
GFXIMVP_PHASE2 | 0.002 | – | 2.100R |
GFXIMVP_PHASE3 | 0.002 | 1,100 | 2.100R |
GFXIMVP_Q1S1 | 0.000 | – | – |
GFXIMVP_Q1S2 | 0.000 | – | – |
GFXIMVP_Q1S3 | 0.000 | – | – |
GMUX_IOEXP_ADDR_SEL | 0.000 | – | – |
GND_5V3V3_AGND | 0.000 | – | – |
GND_AUDIO_CODEC | 0.000 | – | – |
GND_BKLT_SGND | 0.000 | – | – |
GND_CALPE_AVSS | 0.000 | – | – |
GND_FAN | 0.00 | – | – |
GND_P3V3G3HRTC_AGND | 0.00 | – | – |
GND_SMC_AVSS | 0.000 | – | – |
GPU_AUD_PORT_CONN<1> | 0.460 | – | – |
GPU_AUD_PORT_CONN<2> | 0.460 | – | – |
GPU_AUD<0> | 0.407 | – | – |
GPU_AUD<1> | 0.430 | – | – |
GPU_AUX_ZVSS | 0.152 | – | – |
GPU_BIF_GEN3_EN_A | 0.430 | – | – |
GPU_BP_0 | 0.513 | – | – |
GPU_BP_1 | 0.510 | – | – |
GPU_BRD_CFG<1> | 0.462 | – | – |
GPU_CLK_IN | 0.747 | – | – |
GPU_CLK_IN_R | 0.726 | – | – |
GPU_CLK_YA740_OE | 0.620 | – | – |
GPU_CLKREQ_EN | 0.481 | – | – |
GPU_CLKREQ_L | 0.461 | – | – |
GPU_CLKREQ_L_R | 0.496 | – | – |
GPU_DBG_8 | 0.469 | – | – |
GPU_DBG_9 | 0.468 | – | – |
GPU_DBG_10 | 0.470 | – | – |
GPU_DBG_11 | 0.470 | – | – |
GPU_DIECRACKMON | 0.001 | – | 0.300R |
GPU_FB_SNS_COMMON_NEG | 0.001 | – | 0.500R |
GPU_GFX_OVERTEMP | 0.415 | – | – |
GPU_GFX_OVERTEMP_R | 0.554 | – | – |
GPU_GPIO_SVC_R | 0.485 | – | – |
GPU_GPIO_SVD_R | 0.494 | – | – |
GPU_JTAG_TCK | 0.415 | – | – |
GPU_JTAG_TDI | 0.414 | – | – |
GPU_JTAG_TDO | 0.417 | – | – |
GPU_JTAG_TMS | 0.413 | – | – |
GPU_JTAG_TRST_L | 0.416 | – | – |
GPU_MPLS_PS_0 | 0.470 | – | – |
GPU_MPLS_PS_1 | 0.469 | – | – |
GPU_MPLS_PS_2 | 0.468 | – | – |
GPU_MPLS_PS_3 | 0.470 | – | – |
GPU_PCIE_ZVSS | 0.203 | – | – |
GPU_PLLCHARZ_H | 0.318 | – | – |
GPU_PLLCHARZ_RC_H | OL | – | – |
GPU_PLLCHARZ_RC_L | OL | – | – |
GPU_RESET_L | 0.708 | – | – |
GPU_RESET_L_R | 0.684 | – | – |
GPU_RESET_R_L | 0.708 | – | – |
GPU_ROM_CONFIG<1> | 0.414 | – | – |
GPU_ROM_CONFIG<2> | 0.408 | – | – |
GPU_ROM_CS_L | OL | – | – |
GPU_ROM_CS_L_R | 0.407 | – | – |
GPU_ROM_SCLK | OL | – | – |
GPU_ROM_SCLK_R | 0.413 | – | – |
GPU_ROM_SI | OL | – | – |
GPU_ROM_SI_R | 0.407 | – | – |
GPU_ROM_SO | 0.430 | – | – |
GPU_ROM_SO_R | OL | – | – |
GPU_ROM_WP_L | OL | – | – |
GPU_SMB_CLK | 0.493 | – | – |
GPU_SMB_DAT | 0.491 | – | – |
GPU_SMBUS_ADDR<0> | 0.512 | – | – |
GPU_SMBUS_ADDR<1> | 0.460 | – | – |
GPU_TDIODE_N | 0.657 | – | – |
GPU_TDIODE_P | 0.843 | – | – |
GPU_TEST_EN | 0.814 | – | – |
GPU_TEST_PG | 0.797 | – | – |
GPU_TEST_PG_BACON | 0.816 | – | – |
GPU_TX_HALF_SWING | 0.409 | – | – |
GPU_VCORE_IOUT_REF | OL | – | – |
GPU_VCORE_IOUT_REF_R | OL | – | – |
GPU_VGA_DIS | 0.411 | – | – |
GPU_VRAM_STRAP | 0.414 | – | – |
GPUCOREVSENSE_IN | 0.000 | – | – |
GPUFB_AGND | 0.000 | – | – |
GPUFB_BOOT_RC | 0.574 | – | – |
GPUFB_CS_N | 0.053 | 1,350 | 52.000R |
GPUFB_CS_P | 0.053 | 1,350 | 52.000R |
GPUFB_DRVH | 0.557 | – | – |
GPUFB_DRVH_R | 0.550 | – | – |
GPUFB_FSEL | 0.559 | – | – |
GPUFB_GPU_OCSET_R | 0.053 | – | 54.500R |
GPUFB_GPU_VO_R | 0.053 | – | 52.200R |
GPUFB_LL | 0.055 | 1,350 | 54.400R |
GPUFB_OCSET | 0.556 | – | – |
GPUFB_PGOOD | 0.481 | – | – |
GPUFB_RTN_DIV | 0.541 | – | – |
GPUFB_SENSE_DIV | 0.540 | – | – |
GPUFB_SET_R | 0.559 | – | – |
GPUFB_SET0 | 0.559 | – | – |
GPUFB_SET1 | 0.559 | – | – |
GPUFB_SREF | 0.556 | – | – |
GPUFB_VBST | 0.577 | – | – |
GPUFB_VO | 0.553 | – | – |
GPUVCORE_COMP | 0.609 | – | – |
GPUVCORE_COMP_C | OL | – | – |
GPUVCORE_EN | 0.575 | – | – |
GPUVCORE_FB | 0.572 | – | – |
GPUVCORE_FB_R | OL | – | – |
GPUVCORE_FB2 | 0.622 | – | – |
GPUVCORE_NTC | 0.636 | – | – |
GPUVCORE_PGOOD | 0.558 | – | – |
GPUVCORE_SENSE_N | 0.000 | – | – |
GPUVCORE_SENSE_P | 0.000 | – | – |
GPUVCORE_SVC | 0.518 | – | – |
GPUVCORE_SVC_R | 0.501 | – | – |
GPUVCORE_SVD | 0.523 | – | – |
GPUVCORE_SVD_R | 0.512 | – | – |
GPUVCORE_SVT | 0.502 | – | – |
GPUVCORE_SVT_R | 0.501 | – | – |
GPUVCORE_VR_HOT_L | 0.430 | – | – |
GPUVDDC_PCC_ALERT_L | 0.432 | – | – |
GPUVDDC_PCC_ALERT_R_L | OL | – | – |
GPUVR_ISUM_IOUT | OL | – | – |
GPUVR_ISUM_IOUT_R | OL | – | – |
GT_ISUMN_R | 1.013 | – | – |
HRN_BT_DEV_WAKE | 0.489 | – | – |
HS_3V3_X_IOUT | 0.698 | – | – |
HS_MIC_N | 0.628 | – | – |
HS_MIC_P | 0.630 | – | – |
HS_OTHER5V_IOUT | 0.695 | – | – |
HS_P3V3_G3W_SSD0_OUT | 0.698 | – | – |
HS_P3V3_G3W_SSD1_OUT | OL | – | – |
HS_PBUS_MAIN_SSD0_OUT | 0.687 | – | – |
HS_PBUS_MAIN_SSD1_OUT | OL | – | – |
I2C_ALS_SCL | 0.470 | – | – |
I2C_ALS_SDA | 0.470 | – | – |
I2C_BATT_SDA_R | 0.492 | – | – |
I2C_BKLT_SCL | 0.530 | – | – |
I2C_BKLT_SDA | 0.530 | – | – |
I2C_CAM_ISOL_SCL | 0.480 | – | – |
I2C_CAM_ISOL_SDA | 0.480 | – | – |
I2C_CODEC_SCL | 0.478 | – | – |
I2C_CODEC_SDA | 0.479 | – | – |
I2C_DFR_SCL | 0.479 | – | – |
I2C_DFR_SCL_R | 0.47 | – | – |
I2C_DFR_SDA | 0.478 | – | – |
I2C_DFR_SDA_R | 0.47 | – | – |
I2C_DISP_SCL | 0.489 | – | – |
I2C_DISP_SDA | 0.488 | – | – |
I2C_FTCAM_SCL | 0.455 | – | – |
I2C_FTCAM_SDA | 0.455 | – | – |
I2C_KBD_SCL | OL | – | – |
I2C_KBD_SDA | OL | – | – |
I2C_PWR_SCL | 0.45 | – | – |
I2C_PWR_SDA | 0.45 | – | – |
I2C_SEP_SCL | 0.483 | – | – |
I2C_SEP_SDA | 0.480 | – | – |
I2C_SNS_G3S_SCL | 0.484 | – | – |
I2C_SNS_G3S_SDA | 0.488 | – | – |
I2C_SNS0_S0_5V_SCL | OL | – | – |
I2C_SNS0_S0_5V_SDA | OL | – | – |
I2C_SNS0_S0_SCL | 0.489 | – | – |
I2C_SNS0_S0_SDA | 0.489 | – | – |
I2C_SNS1_S0_SCL | 0.484 | – | – |
I2C_SNS1_S0_SDA | 0.484 | – | – |
I2C_SPKRAMP_L_SCL | 0.386 | – | – |
I2C_SPKRAMP_L_SDA | 0.386 | – | – |
I2C_SPKRAMP_R_SCL | 0.388 | – | – |
I2C_SPKRAMP_R_SDA | 0.388 | – | – |
I2C_SSD_SCL | 0.484 | – | – |
I2C_SSD_SDA | 0.485 | – | – |
I2C_SSD0_SCL | 0.508 | – | – |
I2C_SSD0_SDA | 0.509 | – | – |
I2C_SSD1_SCL | OL | – | – |
I2C_SSD1_SDA | OL | – | – |
I2C_TBT_T_SCL | 0.59 | – | – |
I2C_TBT_T_SDA | 0.59 | – | – |
I2C_TBT_TA_INT_L | 0.70 | – | – |
I2C_TBT_TB_INT_L | 0.69 | – | – |
I2C_TBT_X_SCL | 0.60 | – | – |
I2C_TBT_X_SDA | 0.60 | – | – |
I2C_TBT_XA_INT_L | 0.69 | – | – |
I2C_TBT_XB_INT_L | 0.70 | – | – |
I2C_TCON_SCL | 0.500 | – | – |
I2C_TCON_SDA | 0.500 | – | – |
I2C_TPAD_SDA_R | 0.47 | – | – |
I2C_TPAD3V3_SCL | 0.89 | – | – |
I2C_TPAD3V3_SCL_R | 0.87 | – | – |
I2C_TPAD3V3_SDA | 0.933 | – | – |
I2C_TPAD3V3_SDA_R | 0.87 | – | – |
I2C_UPC_SCL | 0.485 | – | – |
I2C_UPC_SDA | 0.488 | – | – |
I2C_UPC_T_SCL2 | 0.48 | – | – |
I2C_UPC_T_SDA2 | 0.48 | – | – |
I2C_UPC_TA_DBG_CTL_SCL | 0.777 | – | – |
I2C_UPC_TA_DBG_CTL_SDA | 0.776 | – | – |
I2C_UPC_TB_DBG_CTL_SCL | 0.776 | – | – |
I2C_UPC_TB_DBG_CTL_SDA | 0.775 | – | – |
I2C_UPC_X_SCL2 | 0.48 | – | – |
I2C_UPC_X_SDA2 | 0.48 | – | – |
I2C_UPC_XA_DBG_CTL_SCL | 0.53 | – | – |
I2C_UPC_XA_DBG_CTL_SDA | 0.55 | – | – |
I2C_UPC_XB_DBG_CTL_SCL | 0.76 | – | – |
I2C_UPC_XB_DBG_CTL_SDA | 0.76 | – | – |
I2S_CODEC_BCLK | 0.477 | – | – |
I2S_CODEC_D2R | 0.473 | – | – |
I2S_CODEC_LRCLK_R | 0.494 | – | – |
I2S_CODEC_R2D | 0.465 | – | – |
I2S_SPKRAMP_L_BCLK | 0.388 | – | – |
I2S_SPKRAMP_L_D2R | 0.378 | – | – |
I2S_SPKRAMP_L_D2R_R1 | 0.385 | – | – |
I2S_SPKRAMP_L_D2R_R2 | 0.386 | – | – |
I2S_SPKRAMP_L_LRCLK_R | 0.386 | – | – |
I2S_SPKRAMP_L_R2D | 0.387 | – | – |
I2S_SPKRAMP_R_BCLK | 0.387 | – | – |
I2S_SPKRAMP_R_D2R_R1 | 0.388 | – | – |
I2S_SPKRAMP_R_D2R_R2 | 0.387 | – | – |
I2S_SPKRAMP_R_LRCLK_R | 0.386 | – | – |
I2S_SPKRAMP_R_R2D | 0.387 | – | – |
IAPC_OPA_OUT | OL | – | – |
IMON_A_CPUCORE | 0.626 | – | – |
IMON_B_CPUGT | 0.623 | – | – |
IMON_C_CPUSA | 0.626 | – | – |
IPD_LID_OPEN | 0.70 | – | – |
IPD_LID_OPEN_R | OL | – | – |
ISNS_1V0_N | OL | – | – |
ISNS_1V0_P | OL | – | – |
ISNS_2V5_S3_N | 0.360 | – | – |
ISNS_2V5_S3_P | 0.360 | – | – |
ISNS_CALPE_IOUT | 0.693 | – | – |
ISNS_CALPE_N | 0.426 | – | – |
ISNS_CALPE_P | 0.426 | – | – |
ISNS_CPUDDR_IOUT | OL | – | – |
ISNS_CPUDDR_N | 0.163 | 1,200 | – |
ISNS_CPUDDR_P | 0.163 | 1,200 | – |
ISNS_CPUSA_IOUT | OL | – | – |
ISNS_CPUVCCIO_NEG | 0.085 | – | 83.500R |
ISNS_CPUVCCIO_POS | 0.085 | – | 83.700R |
ISNS_CPUVDDQ_N | OL | – | – |
ISNS_CPUVDDQ_P | OL | – | – |
ISNS_DDR_IOUT | 0.718 | – | – |
ISNS_GPU_HS_N | 0.400 | 12,600 | – |
ISNS_GPU_HS_P | 0.431 | 12,600 | – |
ISNS_GPU1V8_IOUT | OL | – | – |
ISNS_GPU1V8_N | OL | – | – |
ISNS_GPU1V8_P | OL | – | – |
ISNS_GPUFB_IOUT | OL | – | – |
ISNS_GPUFBIC_IOUT | OL | – | – |
ISNS_GPUFBIC_N | OL | – | – |
ISNS_GPUFBIC_P | OL | – | – |
ISNS_GPUVDDCI_IOUT | OL | – | – |
ISNS_HS_3V3_T_N | 0.434 | 12,600 | – |
ISNS_HS_3V3_T_OUT | 0.717 | – | – |
ISNS_HS_3V3_T_P | 0.434 | 12,600 | – |
ISNS_HS_3V3_X_N | 0.434 | – | – |
ISNS_HS_3V3_X_P | 0.436 | – | – |
ISNS_HS_COMPUTING_N | 0.434 | 12,600 | – |
ISNS_HS_COMPUTING_OUT | 0.717 | – | – |
ISNS_HS_COMPUTING_P | 0.434 | 12,600 | – |
ISNS_HS_OTHER5V_N | 0.434 | – | – |
ISNS_HS_OTHER5V_P | 0.434 | – | – |
ISNS_LCDBKLT_IOUT | OL | – | – |
ISNS_LCDBKLT_N | 0.434 | 12,600 | – |
ISNS_LCDBKLT_P | 0.434 | 12,600 | – |
ISNS_LCDPANEL_IOUT | OL | – | – |
ISNS_LCDPANEL_N | OL | – | – |
ISNS_LCDPANEL_P | OL | – | – |
ISNS_P3V3_G3W_SSD0_N | 0.428 | – | – |
ISNS_P3V3_G3W_SSD0_P | 0.428 | – | – |
ISNS_P3V3_G3W_SSD1_N | OL | – | – |
ISNS_P3V3_G3W_SSD1_P | OL | – | – |
ISNS_P3V3S_WLAN_IOUT | OL | – | – |
ISNS_PP3V3S0_IOUT | OL | – | – |
ISNS_PPBUS_MAIN_SSD0_N | 0.434 | 12,600 | – |
ISNS_PPBUS_MAIN_SSD0_P | 0.432 | 12,600 | – |
ISNS_PPBUS_MAIN_SSD1_N | OL | – | – |
ISNS_PPBUS_MAIN_SSD1_P | OL | – | – |
ISNS_T139_N | OL | – | – |
ISNS_T139_P | OL | – | – |
ISNS_TBT_T_IOUT | OL | – | – |
ISNS_TBT_T_N | OL | – | – |
ISNS_TBT_T_P | OL | – | – |
ISNS_TBT_X_IOUT | OL | – | – |
ISNS_TBT_X_N | OL | – | – |
ISNS_TBT_X_P | OL | – | – |
ISNS_VCCIO_IOUT | OL | – | – |
ISNS_WL1V8_IOUT | OL | – | – |
ISNS_WL1V8_N | OL | – | – |
ISNS_WL1V8_P | OL | – | – |
ISNS_WLAN_N | OL | – | – |
ISNS_WLAN_P | OL | – | – |
ISNS_WLAN_R_N | OL | – | – |
ISNS_WLAN_R_P | OL | – | – |
JTAG_ISP_TCK | 0.564 | – | – |
JTAG_ISP_TDI | 0.563 | – | – |
JTAG_TBT_T_TMS | 0.603 | – | – |
JTAG_TBT_X_TMS | 0.600 | – | – |
KBD_BLC_GSLAT | OL | – | – |
KBD_BLC_GSSCK | OL | – | – |
KBD_BLC_GSSIN | OL | – | – |
KBD_BLC_GSSOUT | OL | – | – |
KBD_BLC_XBLANK | OL | – | – |
KBD_INT_L | OL | – | – |
L83_FILT | 0.800 | – | – |
L83_FLYC | 0.390 | – | – |
L83_FLYN | 0.493 | – | – |
L83_FLYP | 0.402 | – | – |
L83_HSBIAS_FILT | 0.719 | – | – |
L83_HSBIAS_FILT_REF | 0.640 | – | – |
L83_LDO_EN | 0.783 | – | – |
L83_SDOUT | 0.488 | – | – |
L83_VCP_FILT_GND | 0.000 | – | 0.300R |
L83_VCP_FILTN | 0.633 | – | – |
L83_VCP_FILTP | 0.394 | – | – |
LCD_MUX_EN | 0.800 | – | – |
LCD_PWR_SLEW | 0.617 | – | – |
LCD_PWR_SLEW_3V3 | 0.723 | – | – |
LCDBKLT_EN_L | OL | – | – |
LCDBKLT_FB | 0.732 | – | – |
LCDBKLT_FET_DRV | 0.496 | – | – |
LCDBKLT_FET_DRV_R | 0.509 | – | – |
LCDBKLT_SW | 0.430 | – | – |
LCDBKLT_TB_XWR | 1.228 | – | – |
LDO_CORE | 0.380 | – | – |
LDO_RTC | 0.378 | – | – |
LID_CTRL_DMIC | 0.706 | – | – |
LID_OPEN_LEFT | 0.476 | – | – |
LID_OPEN_RIGHT | 0.476 | – | – |
MEM_A_TEN_R | 0.101 | – | – |
MEM_B_TEN_R | 0.100 | – | – |
MEM_RESET_L | 0.383 | – | – |
MEMVTT_EN | 0.549 | – | – |
MEMVTT_EN_R | 0.548 | – | – |
MESA_BOOST_EN | 0.553 | – | – |
MESA_BOOST_EN_CONN | 1.10 | – | – |
MESA_INT | 0.480 | – | – |
MESA_INT_CONN | 1.03 | – | – |
MESA_PWR_EN | 0.474 | – | – |
MIPI_DFR_CLK_CONN_FILT_N | 0.52 | – | – |
MIPI_DFR_CLK_CONN_FILT_P | 0.52 | – | – |
MIPI_DFR_CLK_N | 0.553 | – | – |
MIPI_DFR_CLK_P | 0.557 | – | – |
MIPI_DFR_DATA_CONN_FILT_N | 0.53 | – | – |
MIPI_DFR_DATA_CONN_FILT_P | 0.53 | – | – |
MIPI_DFR_DATA_N | 0.554 | – | – |
MIPI_DFR_DATA_P | 0.550 | – | – |
MIPI_FTCAM_CLK_CONN_N | 0.480 | – | – |
MIPI_FTCAM_CLK_CONN_P | 0.480 | – | – |
MIPI_FTCAM_CLK_ISOL_N | 0.522 | – | – |
MIPI_FTCAM_CLK_ISOL_P | 0.522 | – | – |
MIPI_FTCAM_DATA_CONN_N<0> | 0.490 | – | – |
MIPI_FTCAM_DATA_CONN_P<0> | 0.490 | – | – |
MIPI_FTCAM_DATA_ISOL_N<0> | 0.524 | – | – |
MIPI_FTCAM_DATA_ISOL_P<0> | 0.521 | – | – |
MLB_RAMCFG0 | 0.766 | – | – |
MLB_RAMCFG1 | 0.768 | – | – |
MLB_RAMCFG2 | 0.617 | – | – |
MLB_RAMCFG3 | 0.563 | – | – |
MLB_RAMCFG4 | 0.545 | – | – |
MLBSNS_I2CLS_EN | OL | – | – |
NTC_A_CPUCORE | 0.627 | – | – |
NTC_A_CPUCORE_R | OL | – | – |
NTC_A_CPUCORE_XW | 0.000 | – | – |
NTC_B_CPUCORE_XW | OL | – | – |
NTC_B_CPUGT | 0.626 | – | – |
NTC_B_CPUGT_R | 2.835 | – | – |
P0V8SLPDDR_FB | 0.064 | – | 62.400R |
P0V8SLPDDR_FB_R | 0.064 | – | 63.000R |
P0V8SLPDDR_SW0 | 0.043 | 0,800 | 62.000R |
P0V8SLPDDR_SW1 | 0.045 | 0,800 | 62,000R |
P0V9_LX0_SSD0 | 0.328 | 0,900 | 398,000 |
P0V9_LX0_SSD1 | OL | 0,900 | – |
P0V9_LX1_SSD0 | 0.328 | 0,900 | 398.000 |
P0V9_LX1_SSD1 | OL | 0,900 | – |
P0V9_TBT_T_SVR_AGND | 0.000 | – | 0.300R |
P0V9_TBT_X_SVR_AGND | 0.000 | – | – |
P0V9SLPDDR_FB | 0.074 | – | 72.800R |
P0V9SLPDDR_SW0 | 0.076 | 0,900 | 76.500R |
P0V9SLPDDR_SW1 | 0.076 | 0,900 | 74.300R |
P1V1_SLPDDR_SOCFET_EN | 0.568 | – | – |
P1V1_SLPDDR_SOCFET_EN_R | OL | – | – |
P1V1S0SW_FET_EN | 0.557 | – | – |
P1V1S0SW_RAMP | 0.695 | – | – |
P1V1SLPDDR_RAMP | 0.715 | – | – |
P1V1SLPS2R_FB | 0.365 | – | – |
P1V1SLPS2R_SW0 | 0.366 | 1,100 | 0.001R |
P1V1SLPS2R_SW1 | 0.366 | 1,100 | 0.001R |
P1V2_BOOT_RC | 0.632 | – | – |
P1V2_DRVH | 0.700 | – | – |
P1V2_DRVH_R | 0.702 | – | – |
P1V2_DRVL | 0.490 | – | – |
P1V2_DRVL_R | 0.482 | – | – |
P1V2_LL_SNUB | OL | – | – |
P1V2_PHASE | 0.199 | 1,200 | 160.500 |
P1V2_SNS | 0.173 | – | – |
P1V2_SNS_R | 0.164 | – | – |
P1V2_SW | 0.160 | – | – |
P1V2_VBST | 0.630 | – | – |
P1V2_WLANBT_VLX | 0.315 | – | – |
P1V2REG_AGND | 0.000 | – | – |
P1V2REG_MODE | 0.555 | – | – |
P1V2REG_TRIP | 0.753 | – | – |
P1V2REG_VREF | 0.658 | – | – |
P1V2REG_VREF_R | OL | – | – |
P1V5_WLANBT_VLX | 0.340 | – | – |
P1V5R1V35_GPU_FB_SNS_N | 0.000 | – | – |
P1V5R1V35_GPU_FB_SNS_P | 0.056 | – | 55.200R |
P1V8_G3S_EN_R | OL | – | – |
P1V8_LX0_SSD0 | 0.371 | 1,800 | 0.090R |
P1V8_LX0_SSD1 | OL | 1,800 | – |
P1V8G3S_EN | 0.573 | – | – |
P1V8G3S_SS | 0.723 | – | – |
P1V8GPU_EN | 0.621 | – | – |
P1V8GPU_PGOOD | 0.520 | – | – |
P1V8S5_VALID | 0.718 | – | – |
P1V8SLPS2R_FB | 0.409 | – | – |
P1V8SLPS2R_SW0 | 0.411 | 1,800 | 172.000 |
P1V35FB_EN | 0.537 | – | – |
P2V5_SSD0_AGND | 0.000 | – | – |
P2V5_SSD1_AGND | OL | – | – |
P2V5_SW1_TPS62180_SSD0 | 0.376 | 2,500 | 137,000 |
P2V5_SW1_TPS62180_SSD1 | OL | 2.500 | – |
P2V5_SW2_TPS62180_SSD0 | 0.376 | 2,500 | 137,000 |
P2V5_SW2_TPS62180_SSD1 | OL | – | – |
P2V5_VPP_PGOOD | 0.500 | – | – |
P2V5S3_FSW | 0.360 | – | – |
P2V5S3_REG | 0.360 | 2,500 | – |
P3V3_G3H_RTC_DEBUG_LED_R | OL | – | – |
P3V3_S0GPU_PGOOD | 0.718 | – | – |
P3V3_TBT_T_SX_R | 0.574 | – | – |
P3V3_TBT_X_SX_R | 0.572 | – | – |
P3V3G3H_COMP2 | 0.745 | – | – |
P3V3G3H_CSN2 | 0.420 | – | – |
P3V3G3H_CSP2 | 1.288 | – | – |
P3V3G3H_CSP2_R | 0.420 | – | – |
P3V3G3H_DRVH | 0.996 | – | – |
P3V3G3H_DRVL | 0.563 | – | – |
P3V3G3H_EN | 0.583 | – | – |
P3V3G3H_RF | 0.583 | – | – |
P3V3G3H_SNUBR | OL | – | – |
P3V3G3H_SW | 0.427 | – | – |
P3V3G3H_TG | 0.997 | – | – |
P3V3G3H_VBST | 0.636 | – | – |
P3V3G3H_VBST_R | 0.637 | – | – |
P3V3G3H_VFB2 | 0.585 | – | – |
P3V3G3H_VFB2_R | 0.420 | – | – |
P3V3G3H_VFB2_RR | 1.380 | – | – |
P3V3G3H_VSW | 0.427 | 3,300 | 425.200 |
P3V3G3HRTC_FB | 1.38 | – | – |
P3V3G3HRTC_FB_R | 0.440 | – | – |
P3V3G3HRTC_PGOOD | 0.68 | – | – |
P3V3G3HRTC_PHASE1 | 0.429 | 3,300 | – |
P3V3G3HRTC_PHASE2 | 0.429 | 3,300 | 0.010R |
P3V3G3HRTC_RA_R | 0.440 | – | – |
P3V3G3HRTC_SS | 0.53 | – | – |
P3V3G3S_EN | 0.541 | – | – |
P3V3G3ST_SS | 0.724 | – | – |
P3V3G3SX_SS | 0.723 | – | – |
P3V3GPU_EN | 0.523 | – | – |
P3V3GPU_RAMP | 0.718 | – | – |
P3V3MAIN_PGOOD | 0.578 | – | – |
P3V3S5_COMP2_R | OL | – | – |
P3V3TBTT_RAMP | 0.624 | – | – |
P3V3TBTX_RAMP | 0.723 | – | – |
P5_S0GPU_PGOOD | 0.718 | – | – |
P5GPU_RAMP | 0.619 | – | – |
P5V_3V3G3H_EN | 0.585 | – | – |
P5VG3S_COMP1 | 0.751 | – | – |
P5VG3S_CSN1 | 0.409 | 5,000 | – |
P5VG3S_CSP1 | 0.994 | – | – |
P5VG3S_CSP1_R | 0.409 | 5,000 | – |
P5VG3S_DRVH | 0.980 | – | – |
P5VG3S_DRVL | 0.563 | – | – |
P5VG3S_EN | 0.583 | – | – |
P5VG3S_EN_R | 0.583 | – | – |
P5VG3S_PGOOD | 0.578 | – | – |
P5VG3S_SNUBR | OL | – | – |
P5VG3S_SW | 0.409 | – | – |
P5VG3S_TG | 0.977 | – | – |
P5VG3S_VBST | 0.636 | – | – |
P5VG3S_VBST_R | 0.637 | – | – |
P5VG3S_VFB1 | 0.578 | – | – |
P5VG3S_VFB1_R | 0.406 | – | – |
P5VG3S_VSW | 0.408 | 5,000 | – |
P5VP3V3_SKIPSEL | 0.477 | – | – |
P5VP3V3_VREF2 | 0.480 | – | – |
P5VP3V3_VREG3 | 0.511 | – | – |
P5VS4_COMP1_R | OL | – | – |
P5VUSBC_X_AGND | 0.000 | – | – |
P5VUSBC_X_BOOT_RC | 0.616 | – | – |
P5VUSBC_X_DRVH | 0.716 | – | – |
P5VUSBC_X_DRVH_R | 0.715 | – | – |
P5VUSBC_X_FSEL | 0.558 | – | – |
P5VUSBC_X_LL | 0.244 | 5,000 | 500.000R |
P5VUSBC_X_NEG | 0.244 | – | – |
P5VUSBC_X_OCSET | 0.551 | – | – |
P5VUSBC_X_PGOOD | 0.553 | – | – |
P5VUSBC_X_POS | 0.244 | – | – |
P5VUSBC_X_R | 0.244 | 5,000 | 0.000R |
P5VUSBC_X_RTN_DIV | 0.555 | – | – |
P5VUSBC_X_RTN_DIV_XW | 0.000 | – | – |
P5VUSBC_X_SENSE_DIV | 0.550 | – | – |
P5VUSBC_X_SENSE_DIV_XW | 0.244 | – | – |
P5VUSBC_X_SET_R | OL | – | – |
P5VUSBC_X_SET0 | 0.558 | – | – |
P5VUSBC_X_SET1 | 0.556 | – | – |
P5VUSBC_X_SREF | 0.556 | – | – |
P5VUSBC_X_VBST | 0.611 | – | – |
P5VUSBC_X_VO | 0.552 | – | – |
P5VUSBCT_AGND | 0.000 | – | – |
P5VUSBCT_BOOT_RC | 0.612 | – | – |
P5VUSBCT_DRVH | 0.685 | – | – |
P5VUSBCT_DRVH_R | 0.668 | – | – |
P5VUSBCT_FSEL | 0.554 | – | – |
P5VUSBCT_LL | 0.215 | 5,000 | 213.700R |
P5VUSBCT_N | 0.215 | – | – |
P5VUSBCT_OCSET | 0.548 | – | – |
P5VUSBCT_P | 0.215 | – | – |
P5VUSBCT_R | 0.215 | 5,000 | 213.700R |
P5VUSBCT_RTN_DIV | 0.551 | – | – |
P5VUSBCT_RTN_DIV_R | 0.000 | – | – |
P5VUSBCT_SENSE_DIV | 0.547 | – | – |
P5VUSBCT_SENSE_DIV_R | 0.216 | – | – |
P5VUSBCT_SET_R | OL | – | – |
P5VUSBCT_SET0 | 0.550 | – | – |
P5VUSBCT_SET1 | 0.552 | – | – |
P5VUSBCT_SREF | 0.551 | – | – |
P5VUSBCT_VBST | 0.610 | – | – |
P5VUSBCT_VO | 0.547 | – | – |
PANEL_P3V3_EN | 0.572 | – | – |
PANEL_P3V3_EN_D | 0.764 | – | – |
PANEL_P5V_EN | 0.569 | – | – |
PANEL_P5V_EN_D | 1.043 | – | – |
PBUS_DIVIDER | 0.708 | – | – |
PBUS_DIVIDER_REF | 0.670 | – | – |
PBUS_S0_VSENSE | OL | – | – |
PBUS_S0_VSENSE_IN | 0.437 | – | – |
PBUSVSENS_EN_L | 0.505 | – | – |
PBUSVSENS_EN_L_DIV | OL | – | – |
PCC_B | OL | – | – |
PCC_CEXT | OL | – | – |
PCC_CLR_L | OL | – | – |
PCC_EVENT | 0.493 | – | – |
PCC_EVENT_3V3 | OL | – | – |
PCC_EVENT_R | OL | – | – |
PCH_1V0_IOUT | OL | – | – |
PCH_BATLOW_L | 0.811 | – | – |
PCH_BT_DEV_WAKE | 0.635 | – | – |
PCH_BT_ROM_BOOT_L | 0.575 | – | – |
PCH_CLK24M_XTALIN | 0.837 | – | – |
PCH_CLK24M_XTALOUT | 0.833 | – | – |
PCH_CLK24M_XTALOUT_R | 0.834 | – | – |
PCH_CLK32K_RTCX1 | 0.862 | – | – |
PCH_CLKIN_XTAL | 0.832 | – | – |
PCH_CPU_TRIGGER | 0.433 | – | – |
PCH_CPU_TRIGGER_R | 0.406 | – | – |
PCH_DISPA_SDI | 0.336 | – | – |
PCH_DRAM_RESET_L | 0.384 | – | – |
PCH_ESPI_ALERT0_L | 0.820 | – | – |
PCH_GPP_A0_PU | 0.820 | – | – |
PCH_GPPJ_RCOMP_1P8 | 0.202 | – | – |
PCH_GPU_CLKREQ_L | 0.813 | – | – |
PCH_INTRUDER_L | 0.843 | – | – |
PCH_ITP_PMODE | 0.405 | – | – |
PCH_PCIE_CLK100M_WLAN_N | 0.351 | – | – |
PCH_PCIE_CLK100M_WLAN_P | 0.350 | – | – |
PCH_PCIE_RCOMPN | 0.325 | – | – |
PCH_PCIE_RCOMPP | 0.326 | – | – |
PCH_PECI | 0.397 | – | – |
PCH_PM_THRMTRIP_L_R | 0.364 | – | – |
PCH_PMTHRMTRIP_L | 0.525 | – | – |
PCH_PMTHRMTRIP_L_R | 0.539 | – | – |
PCH_PROCPWRGD | 0.361 | – | – |
PCH_RTC_RESET_L | 0.771 | – | – |
PCH_SOC_SYNC | 0.477 | – | – |
PCH_STRP_BSSB_SEL_GPIO | 0.365 | – | – |
PCH_STRP_CNV_L | 0.620 | – | – |
PCH_STRP_ESPI | 0.811 | – | – |
PCH_STRP_GPD7 | 0.817 | – | – |
PCH_STRP_NO_REBOOT | 0.806 | – | – |
PCH_STRP_VCCPSPI_1V8 | 0.550 | – | – |
PCH_STRP_XTAL_24MHZ | 0.608 | – | – |
PCH_SWD_SOC_CLK | 0.635 | – | – |
PCH_SWD_SOC_IO | 0.635 | – | – |
PCH_UART_BT_CTS_L | 0.710 | – | – |
PCH_UART_BT_D2R | 0.711 | – | – |
PCH_UART_BT_R2D | 0.715 | – | – |
PCH_UART_BT_RTS_L | 0.714 | – | – |
PCH_UART_DEBUG_D2R | 0.773 | – | – |
PCH_UART_DEBUG_R2D | 0.773 | – | – |
PCH_WLAN_CLKREQ_L | 0.812 | – | – |
PCH_WLAN_CLKREQ_R_L | 0.535 | – | – |
PCH_WLAN_DEV_WAKE | 0.747 | – | – |
PCH_WLAN_PERST_L | 0.829 | – | – |
PCIE_CLK100M_DEBUG_N | 0.348 | – | – |
PCIE_CLK100M_DEBUG_P | 0.350 | – | – |
PCIE_CLK100M_LIFEBOAT_N | 0.125 | – | – |
PCIE_CLK100M_LIFEBOAT_P | 0.125 | – | – |
PCIE_CLK100M_SOC_N | 0.325 | – | – |
PCIE_CLK100M_SOC_P | 0.327 | – | – |
PCIE_LIFEBOAT_CLKREQ_L | 0.482 | – | – |
PCIE_LIFEBOAT_D2R_N | 0.407 | – | – |
PCIE_LIFEBOAT_D2R_P | 0.406 | – | – |
PCIE_LIFEBOAT_R2D_C_N | 0.338 | – | – |
PCIE_LIFEBOAT_R2D_C_P | 0.339 | – | – |
PCIE_LIFEBOAT_RESET_L | 0.482 | – | – |
PCIE_WAKE_L | 0.814 | – | – |
PDM_DMIC_CLK0 | 0.518 | – | – |
PDM_DMIC_CLK1 | 0.514 | – | – |
PDM_DMIC_DATA0 | 0.491 | – | – |
PDM_DMIC_DATA0_RR | 0.525 | – | – |
PDM_DMIC_DATA0_UNSEC | 0.718 | – | – |
PDM_DMIC_DATA1_RR | 0.525 | – | – |
PDM_DMIC_DATA1_UNSEC | 0.717 | – | – |
PEG_GPU_D2R_C_N<0> | 0.314 | – | – |
PEG_GPU_D2R_C_N<1> | 0.313 | – | – |
PEG_GPU_D2R_C_N<2> | 0.313 | – | – |
PEG_GPU_D2R_C_N<3> | 0.315 | – | – |
PEG_GPU_D2R_C_N<4> | 0.314 | – | – |
PEG_GPU_D2R_C_N<5> | 0.314 | – | – |
PEG_GPU_D2R_C_N<6> | 0.314 | – | – |
PEG_GPU_D2R_C_N<7> | 0.315 | – | – |
PEG_GPU_D2R_C_P<0> | 0.314 | – | – |
PEG_GPU_D2R_C_P<1> | 0.312 | – | – |
PEG_GPU_D2R_C_P<2> | 0.312 | – | – |
PEG_GPU_D2R_C_P<3> | 0.315 | – | – |
PEG_GPU_D2R_C_P<4> | 0.312 | – | – |
PEG_GPU_D2R_C_P<5> | 0.313 | – | – |
PEG_GPU_D2R_C_P<6> | 0.314 | – | – |
PEG_GPU_D2R_C_P<7> | 0.314 | – | – |
PEG_GPU_D2R_N<0> | 0.292 | – | – |
PEG_GPU_D2R_N<1> | 0.292 | – | – |
PEG_GPU_D2R_N<2> | 0.292 | – | – |
PEG_GPU_D2R_N<3> | 0.292 | – | – |
PEG_GPU_D2R_N<4> | 0.292 | – | – |
PEG_GPU_D2R_N<5> | 0.292 | – | – |
PEG_GPU_D2R_N<6> | 0.292 | – | – |
PEG_GPU_D2R_N<7> | 0.293 | – | – |
PEG_GPU_D2R_P<0> | 0.295 | – | – |
PEG_GPU_D2R_P<1> | 0.294 | – | – |
PEG_GPU_D2R_P<2> | 0.294 | – | – |
PEG_GPU_D2R_P<3> | 0.295 | – | – |
PEG_GPU_D2R_P<4> | 0.292 | – | – |
PEG_GPU_D2R_P<5> | 0.295 | – | – |
PEG_GPU_D2R_P<6> | 0.296 | – | – |
PEG_GPU_D2R_P<7> | 0.295 | – | – |
PEG_GPU_R2D_C_N<0> | 0.239 | – | – |
PEG_GPU_R2D_C_N<1> | 0.237 | – | – |
PEG_GPU_R2D_C_N<2> | 0.239 | – | – |
PEG_GPU_R2D_C_N<3> | 0.238 | – | – |
PEG_GPU_R2D_C_N<4> | 0.239 | – | – |
PEG_GPU_R2D_C_N<5> | 0.240 | – | – |
PEG_GPU_R2D_C_N<6> | 0.240 | – | – |
PEG_GPU_R2D_C_N<7> | 0.239 | – | – |
PEG_GPU_R2D_C_P<0> | 0.238 | – | – |
PEG_GPU_R2D_C_P<1> | 0.236 | – | – |
PEG_GPU_R2D_C_P<2> | 0.238 | – | – |
PEG_GPU_R2D_C_P<3> | 0.238 | – | – |
PEG_GPU_R2D_C_P<4> | 0.239 | – | – |
PEG_GPU_R2D_C_P<5> | 0.239 | – | – |
PEG_GPU_R2D_C_P<6> | 0.240 | – | – |
PEG_GPU_R2D_C_P<7> | 0.240 | – | – |
PEG_GPU_R2D_N<0> | 0.393 | – | – |
PEG_GPU_R2D_N<1> | 0.393 | – | – |
PEG_GPU_R2D_N<2> | 0.392 | – | – |
PEG_GPU_R2D_N<3> | 0.393 | – | – |
PEG_GPU_R2D_N<4> | 0.393 | – | – |
PEG_GPU_R2D_N<5> | 0.392 | – | – |
PEG_GPU_R2D_N<6> | 0.392 | – | – |
PEG_GPU_R2D_N<7> | 0.393 | – | – |
PEG_GPU_R2D_P<0> | 0.393 | – | – |
PEG_GPU_R2D_P<1> | 0.393 | – | – |
PEG_GPU_R2D_P<2> | 0.391 | – | – |
PEG_GPU_R2D_P<3> | 0.392 | – | – |
PEG_GPU_R2D_P<4> | 0.393 | – | – |
PEG_GPU_R2D_P<5> | 0.392 | – | – |
PEG_GPU_R2D_P<6> | 0.392 | – | – |
PEG_GPU_R2D_P<7> | 0.393 | – | – |
PHV_INT_TA_G3H | 0.645 | – | – |
PHV_INT_TB_G3H | 0.644 | – | – |
PHV_INT_XA_G3H | 0.643 | – | – |
PHV_INT_XB_G3H | 0.62 | – | – |
PLT_RST_L | 0.625 | – | – |
PLT3V3_RST_L | 0.514 | – | – |
PM_ALL_GPU_PGOOD | 0.480 | – | – |
PM_MEMVTT_EN | 0.376 | – | – |
PM_PCH_PWROK | 0.491 | – | – |
PM_PCH_SYS_PWROK | 0.538 | – | – |
PM_PWRBTN_L | 0.765 | – | – |
PM_RSMRST_L | 0.514 | – | – |
PM_SLP_S0_L | OL | – | – |
PM_SLP_S0_R_L | OL | – | – |
PM_SLP_S3_L | 0.560 | – | – |
PM_SLP_S4_L | 0.815 | – | – |
PM_SLP_S5_L | 0.815 | – | – |
PM_SLP_TIEOFF | 0.717 | – | – |
PM_SYNC | 0.434 | – | – |
PM_SYSRST_L | 0.813 | – | – |
PM_SYSRST_R_L | 0.538 | – | – |
PM_THRMTRIP_L | 0.251 | – | – |
PMU_3V3_T_HI_ISENSE | 0.582 | – | – |
PMU_3V3_X_HI_ISENSE | 0.582 | – | – |
PMU_ACTIVE_READY | 0.479 | – | – |
PMU_ACTIVE_READY_R | OL | – | – |
PMU_CLK32K_PCH | 0.809 | – | – |
PMU_CLK32K_PCH_R | 0.776 | – | – |
PMU_CLK32K_SOC | 0.495 | – | – |
PMU_CLK32K_SOC_R | 0.529 | – | – |
PMU_CLK32K_WLANBT | 0.490 | – | – |
PMU_COLD_RESET_L | 0.490 | – | – |
PMU_CPU_ISENSE | 0.587 | – | – |
PMU_CPU_VSENSE | 0.581 | – | – |
PMU_CPUDDR_ISENSE | 0.586 | – | – |
PMU_DDR1V2_ISENSE | 0.581 | – | – |
PMU_DROOP_L | 0.485 | – | – |
PMU_FORCE_DFU | 0.771 | – | – |
PMU_GPU_CORE_ISENSE | 0.584 | – | – |
PMU_GPU_CORE_VSENSE | 0.580 | – | – |
PMU_GPU_FB_ISENSE | 0.585 | – | – |
PMU_IREF | 0.758 | – | – |
PMU_LDO3_OUT | 0.596 | – | – |
PMU_ONOFF_L | 0.699 | – | – |
PMU_ONOFF_R_L | 0.69 | – | – |
PMU_OTHER5V_HI_ISENSE | 0.584 | – | – |
PMU_P1V8_WLAN_ISENSE | 0.586 | – | – |
PMU_P3V3_G3W_SSD0_ISENSE | 0.582 | – | – |
PMU_P3V3_G3W_SSD1_ISENSE | 0.584 | – | – |
PMU_PBUS_BMON_DIS_ISENSE | 0.585 | – | – |
PMU_PBUS_MAIN_SSD0_ISENSE | 0.584 | – | – |
PMU_PBUS_MAIN_SSD1_ISENSE | 0.583 | – | – |
PMU_PVDDMAIN_EN | 0.773 | – | – |
PMU_RSLOC_RST_L | 0.70 | – | – |
PMU_RSLOC_RST_R_L | 0.70 | – | – |
PMU_SYS_ALIVE | 0.436 | – | – |
PMU_VDD_HI | 0.662 | – | – |
PMU_VDD_MAX | 0.553 | – | – |
PMU_VPUMP | 0.583 | – | – |
PMU_VREF | 0.642 | – | – |
PMU_XTAL1_R | 0.800 | – | – |
PMU_XTAL2 | 0.800 | – | – |
PP0V6_S0_DDRVTT | 0.126 | – | – |
PP0V8_SLPS2R | 0.229 | – | – |
PP0V9_SE_VMID | 0.596 | – | – |
PP0V9_SLPDDR | 0.076 | 0,900 | 74.300R |
PP0V9_SLPDDR_SOC_PCIEREFBUF | 0.084 | – | 82.600R |
PP0V9_SSD0 | 0.328 | 0,900 | 398,000 |
PP0V9_SSD0_FB_DIS | 0.405 | – | – |
PP0V9_SSD1 | OL | 0,900 | – |
PP0V9_SSD1_FB_DIS | OL | – | – |
PP0V9_TBT_T_LC | 0.353 | – | – |
PP0V9_TBT_T_LVR | 0.485 | – | – |
PP0V9_TBT_T_PCIE | 0.316 | – | – |
PP0V9_TBT_T_SVR | 0.314 | 0,900 | – |
PP0V9_TBT_X_LVR | 0.486 | – | – |
PP0V9_TBT_X_PCIE | 0.315 | – | – |
PP0V9_TBT_X_SVR | 0.314 | 0,900 | 300.000R |
PP0V82_SLPDDR | 0.045 | 0,800 | 62.000R |
PP0V95_S0_CPUVCCIO_REG_R | 0.076 | – | 75.600R |
PP1V_PRIM_PCH_VCCAMPHYPLL_F | 0.148 | – | – |
PP1V1_SLPDDR | 0.355 | – | – |
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F | 0.385 | – | – |
PP1V1_SLPDDR_SOC_XTAL_F | 0.385 | – | – |
PP1V1_SLPS2R | 0.380 | 1,100 | 0.001R |
PP1V1_UPC_TA_LDO_BMC | 0.521 | – | – |
PP1V1_UPC_TB_LDO_BMC | 0.521 | – | – |
PP1V1_UPC_XA_LDO_BMC | 0.521 | – | – |
PP1V1_UPC_XB_LDO_BMC | 0.51 | – | – |
PP1V2_AWAKE | 0.530 | – | – |
PP1V2_AWAKE_SOC_PCIEPLL_F | 0.535 | – | – |
PP1V2_AWAKE_SOC_PCIEREFBUF_F | 0.533 | – | – |
PP1V2_AWAKE_SOC_PLLCPU_F | 0.533 | – | – |
PP1V2_AWAKE_SOC_PLLSOC_F | 0.533 | – | – |
PP1V2_S0SW | 0.324 | – | – |
PP1V2_S3 | 0.163 | 1,200 | – |
PP1V2_S3_CPUDDR | 0.161 | – | – |
PP1V2_S3_REG_R | 0,163 | 1,200 | 160.500 |
PP1V2_WLANBT | 0.316 | – | – |
PP1V2_WLANBT_C | 0.315 | – | – |
PP1V05_PRIM | 0.148 | 1,050 | – |
PP1V05_PRIM_PCH_VCCAPLL_F | 0.148 | – | – |
PP1V05_PRIM_PCH_VCCAXTAL_F | 0.148 | – | – |
PP1V05_S0SW | 0.216 | – | – |
PP1V05_S3 | 0.214 | – | – |
PP1V5_WLANBT | 0.339 | – | – |
PP1V5_WLANBT_C | 0.340 | – | – |
PP1V5R1V35_GPU_REG_R | – | 1,350 | 54.400R |
PP1V5R1V35_S0_GPU_IC | 0.053 | 1,350 | 52.600R |
PP1V5R1V35_S0_GPU_MEM | 0.053 | 1,350 | 52.800R |
PP1V8_ACCEL_FILT | OL | – | – |
PP1V8_AUDIO | 0.328 | – | – |
PP1V8_AWAKE | -0.362 | – | – |
PP1V8_AWAKE_SOC_FMON_RC | 0.415 | – | – |
PP1V8_AWAKE_SOC_TSADC_RC | 0.365 | – | – |
PP1V8_DMIC | 0.32 | – | – |
PP1V8_G3S | 0.330 | 1.800 | – |
PP1V8_G3S_WLANBT_VDDIO | 0.331 | – | – |
PP1V8_GPU | 0.277 | – | – |
PP1V8_GPU_TSVDD | 0.277 | – | – |
PP1V8_L83_VCP | 0.329 | – | – |
PP1V8_L83_VCP_R | 0.328 | – | – |
PP1V8_L83_VL | 0.331 | – | – |
PP1V8_L83_VL_R | 0.328 | – | – |
PP1V8_MESA | 0.523 | – | – |
PP1V8_MESA_CONN | 0.52 | – | – |
PP1V8_S0_GPU | 0.277 | – | 280.000R |
PP1V8_S0_GPU_LC_IC | 0.277 | – | – |
PP1V8_S0_PCH_VCCHDA_F | 0.350 | – | – |
PP1V8_S5 | 0.35 | – | – |
PP1V8_S5_CPUTHMSNS_R | 0.377 | – | – |
PP1V8_S5_GPIOX_R | 0.367 | – | – |
PP1V8_S5_GPUTHMSNS_R | OL | – | – |
PP1V8_S5_TBTTHMSNS_T_R | 0.414 | – | – |
PP1V8_S5_TBTTHMSNS_X_R | 0.416 | – | – |
PP1V8_SE_AVDD | 0.317 | – | – |
PP1V8_SE_ESE | 0.360 | – | – |
PP1V8_SLPS2R | 0.411 | 1,800 | 172.000 |
PP1V8_SLPS2R_PMUVDDGPIO | 0.744 | – | – |
PP1V8_SLPS2R_SOC_LPADC_RC | 0.447 | – | – |
PP1V8_SLPS2R_SOC_LPOSC_RC | 0.462 | – | – |
PP1V8_SLPS2RSW_DFR | 0.53 | 1,800 | – |
PP1V8_SSD0 | 0.371 | 1,800 | 0.090R |
PP1V8_SSD0_FB_DIS | 0.378 | – | – |
PP1V8_SSD1 | OL | 1,800 | – |
PP1V8_SSD1_FB_DIS | OL | – | – |
PP1V8_SSD1_S4E2_AVDD18_PLL | OL | – | – |
PP1V8_UPC_TA_LDOA | 0.528 | – | – |
PP1V8_UPC_TA_LDOD | 0.491 | – | – |
PP1V8_UPC_TB_LDOA | 0.527 | – | – |
PP1V8_UPC_TB_LDOD | 0.492 | – | – |
PP1V8_UPC_XA_LDOA | 0.529 | – | – |
PP1V8_UPC_XA_LDOD | 0.491 | – | – |
PP1V8_UPC_XB_LDOA | 0.52 | – | – |
PP1V8_UPC_XB_LDOD | 0.48 | – | – |
PP1V8_VDD_XTAL | 0.279 | – | – |
PP2V5_ADC1_VREF | OL | – | – |
PP2V5_ADC2_VREF | OL | – | – |
PP2V5_NAND_SSD0 | 0.376 | 2,500 | 137,000 |
PP2V5_NAND_SSD1 | OL | 2,500 | – |
PP2V5_S3 | 0.360 | 2,500 | – |
PP3V0_G3H_RTC | 0.517 | – | – |
PP3V0_MESA | 0.561 | – | – |
PP3V0_MESA_CONN | 0.559 | – | – |
PP3V3_G3H_DFR | 0.432 | 3,300 | – |
PP3V3_G3H_MESA_SW | 0.423 | – | – |
PP3V3_G3H_PMU_VINRTC_R | 0.429 | – | – |
PP3V3_G3H_RTC_REG_R | 0.429 | 3,300 | 0.010R |
PP3V3_G3H_RTC_X | 0.41 | – | – |
PP3V3_G3H_SOCPMU | 0.427 | – | – |
PP3V3_G3H_SSD0_SNS | 0.425 | 3,300 | – |
PP3V3_G3H_SSD1_SNS | OL | – | – |
PP3V3_G3H_T | 0.427 | 3,300 | 425.200 |
PP3V3_G3HSW_DFR | 0.56 | – | – |
PP3V3_G3S_AUD_F | 0.337 | – | – |
PP3V3_G3S_T | 0.339 | – | – |
PP3V3_G3S_WLAN | 0.353 | – | – |
PP3V3_G3S_X | 0.352 | – | – |
PP3V3_G3SSW_SNS | 0.517 | – | – |
PP3V3_L83_VP | 0.339 | – | – |
PP3V3_S0_GPU | 0.453 | – | – |
PP3V3_S0SW_LCD | 0.490 | – | – |
PP3V3_S0SW_LCD_R | 0.553 | – | – |
PP3V3_S0SW_TBT_T | 0.535 | – | – |
PP3V3_S0SW_TBT_T_SNS | 0.535 | 3,300 | – |
PP3V3_S0SW_TBT_X | 0.535 | – | – |
PP3V3_S0SW_TBT_X_SNS | 0.537 | 3,300 | – |
PP3V3_S5 | 0.327 | – | – |
PP3V3_S5_GPIOX_R | 0.328 | – | – |
PP3V3_TBT_T_ANA_PCIE | 0.520 | – | – |
PP3V3_TBT_T_ANA_USB2 | 0.496 | – | – |
PP3V3_TBT_T_F | 0.535 | 3,300 | – |
PP3V3_TBT_T_LC | 0.577 | – | – |
PP3V3_TBT_T_SX | 0.538 | – | – |
PP3V3_TBT_X_ANA | 0.537 | – | – |
PP3V3_TBT_X_ANA_PCIE | 0.51 | – | – |
PP3V3_TBT_X_F | 0.537 | 3,300 | – |
PP3V3_TBT_X_LC | 0.56 | – | – |
PP3V3_TBT_X_SX | 0.538 | – | – |
PP3V3_UPC_TA_LDO | 0.514 | – | – |
PP3V3_UPC_TB_LDO | 0.514 | – | – |
PP3V3_UPC_XA_LDO | 0.517 | – | – |
PP3V3_UPC_XB_LDO | 0.50 | – | – |
PP3V3_VREF_PCC | OL | – | – |
PP4V7_SE_TVDD | 0.352 | – | – |
PP5V_COREVR_VCC | 0.401 | – | – |
PP5V_EADC1_AVDD | OL | – | – |
PP5V_EADC2_AVDD | OL | – | – |
PP5V_EDRAM_V5IN | 0.410 | – | – |
PP5V_G3S | 0.408 | 5,000 | – |
PP5V_G3S_BKLT_A | 0.409 | – | – |
PP5V_G3S_BKLT_D | 0.410 | – | – |
PP5V_G3S_DFR_FILT | 0.39 | – | – |
PP5V_G3S_FAN_CONN | 0.39 | – | – |
PP5V_G3S_GFXIMVP_VDD | 0.409 | – | – |
PP5V_G3S_GFXIMVP_VDDP | 0.408 | – | – |
PP5V_G3S_ISNS_D | OL | – | – |
PP5V_G3S_TPAD_CONN | 0.39 | – | – |
PP5V_G3S_VCCIOVCC | 0.411 | – | – |
PP5V_S0_ALSCAM_F | 0.386 | – | – |
PP5V_S0_GPUFET | 0.567 | – | – |
PP5V_S0_PCCAMP | OL | – | – |
PP5V_S0GPU_P1V35_GPU | 0.408 | – | – |
PP5V_S0SW_LCD | 0.566 | – | – |
PP5V_S4_T_USBC | 0.215 | 5,000 | – |
PP5V_S4_X_USBC | 0.244 | 5,000 | 0.000R |
PP5V_S5_LDO | 0.481 | – | – |
PP5V_USBC_X_VCC | 0.412 | – | – |
PP5V_USBCT_VCC | 0.412 | – | – |
PP5V_VREF_PCC | OL | – | – |
PP16V0_MESA | 0.655 | – | – |
PP16V0_MESA_CONN | 0.64 | – | – |
PP17V0_MOJAVE_LDOIN | 0.596 | – | – |
PP20V_USBC_TA_VBUS | 0.188 | 20,000 | – |
PP20V_USBC_TA_VBUS_F | 0.188 | 20,000 | – |
PP20V_USBC_TB_VBUS | 0.187 | 20,000 | – |
PP20V_USBC_TB_VBUS_F | 0.185 | 20,000 | – |
PP20V_USBC_XA_VBUS | 0.187 | 20,000 | – |
PP20V_USBC_XA_VBUS_F | 0.188 | 20,000 | – |
PP20V_USBC_XB_VBUS | 0.190 | 20,000 | – |
PP20V_USBC_XB_VBUS_F | 0.190 | 20,000 | – |
PPBUS_G3H | 0.434 | 12,600 | – |
PPBUS_G3H_R_IP0R | OL | – | – |
PPBUS_G3H_SSD0_SNS | 0.433 | 12,600 | – |
PPBUS_G3H_SSD1_SNS | OL | 12,600 | – |
PPBUS_HS_3V3G3H_T | 0.434 | 12,600 | – |
PPBUS_HS_3V3G3HRTC_X | 0.436 | – | – |
PPBUS_HS_CPU | 0.434 | 12,600 | – |
PPBUS_HS_GPU | 0.429 | 12,600 | – |
PPBUS_HS_OTH5V | 0.434 | – | – |
PPDCIN_G3H | 0.540 | 20,000 | – |
PPDCIN_G3H_CHGR | 0.54 | 20,000 | – |
PPVBAT_G3H_CHGR_R | 0.434 | 12,600 | – |
PPVBAT_G3H_CHGR_REG | 0.434 | 12,600 | – |
PPVBAT_G3H_CONN | 1.40 | – | – |
PPVCC_CPU_PH1 | 0.002 | 1,500 | 2.100R |
PPVCC_CPU_PH2 | 0.002 | 1,500 | 2.100R |
PPVCC_CPU_PH3 | 0.002 | 1,500 | 2,100R |
PPVCC_S0_CPU | 0.002 | 1,500 | 2,100R |
PPVCCGT_CPU_PH1 | 0.006 | 1,500 | 5,600R |
PPVCCGT_CPU_PH2 | 0.006 | 1,500 | 5,600R |
PPVCCGT_S0_CPU | 0.006 | 1,500 | 5,600R |
PPVCCIO_S0_CPU | 0.076 | – | – |
PPVCCPRIM_FETIN | 0.129 | – | – |
PPVCCPRIMCORE_PRIM_REG | 0.073 | 1,050 | 143.000 |
PPVCCSA_CPU_R | 0.022 | 1,150 | 22,200R |
PPVCCSA_S0_CPU | 0.022 | 1,150 | 22,200R |
PPVCCSPI_PRIM_PCH | 0.325 | – | – |
PPVCORE_S0_GFX_PH1 | 0.002 | – | 2.100R |
PPVCORE_S0_GFX_PH2 | 0.002 | 1,100 | 2.100R |
PPVCORE_S0_GFX_PH3 | 0.002 | 1,100 | 2.100R |
PPVCORE_S0_GPU | 0,002 | 1,100 | 2.100R |
PPVDDCI_S0_GPU | 0.035 | 0,900 | 34.400R |
PPVDDCPU_AWAKE | 0.019 | 0,625 | 19.000R |
PPVDDCPUSRAM_AWAKE | 0.416 | 1,000 | 411.000 |
PPVIN_G3H_P3V3G3HRTC_R | 0.436 | 3,300 | – |
PPVIN_G3H_TPAD_FUSE | 0.434 | 12.600 | – |
PPVIN_RFLDO_WLANBT | 0.000 | – | – |
PPVIN_RFLDO_WLANBT_C | 0.347 | – | – |
PPVIN_S0_CPUVR_VIN | 0.438 | – | – |
PPVIN_S0_GFXIMVP_VIN | 0.433 | – | – |
PPVIN_S0GPU_1V8_RC | 0.443 | – | – |
PPVIN_S0SW_LCDBKLT | 0.870 | 12,600 | 0.549R |
PPVIN_S0SW_LCDBKLT_FET | 0.434 | 12,600 | – |
PPVIN_S0SW_LCDBKLT_R | 0.434 | 12,600 | – |
PPVIN_S3_DDR2V5_RC | 0.442 | – | – |
PPVIN_SW_LCDBKLT_SW | 0.870 | 12,600 | 0.549R |
PPVOUT_S0_LCDBKLT | 1.142 | 59,000 | – |
PPVTT_VTTREF | 0.507 | – | – |
PROG1_CPUCOREVR | 0.620 | – | – |
PROG2_CPUCOREVR | 0.616 | – | – |
PROG3_CPUCOREVR | 0.598 | – | – |
PROG4_CPUCOREVR | 0.624 | – | – |
PROG5_CPUCOREVR | 0.624 | – | – |
PVCCCGT_PH1_AGND | 0.000 | – | – |
PVCCCGT_PH1_VCC | 0.412 | – | – |
PVCCCGT_PH2_AGND | 0.000 | – | – |
PVCCCGT_PH2_VCC | 0.410 | – | – |
PVCCCORE_PH1_AGND | 0.000 | – | – |
PVCCCORE_PH1_VCC | 0.411 | – | – |
PVCCCORE_PH2_AGND | 0.000 | – | – |
PVCCCORE_PH2_VCC | 0.410 | – | – |
PVCCCORE_PH3_AGND | 0.000 | – | – |
PVCCCORE_PH3_VCC | 0.410 | – | – |
PVCCCSA_AGND | 0.000 | – | – |
PVCCCSA_VCIN | 0.408 | – | – |
PVCCEDRAM_REFIN | 0.707 | – | – |
PVCCIO_BOOT_RC | 0.579 | – | – |
PVCCIO_DRVH | 0.554 | – | – |
PVCCIO_DRVH_R | 0.554 | – | – |
PVCCIO_DRVL | 0.458 | – | – |
PVCCIO_DRVL_R | 0.460 | – | – |
PVCCIO_EN | 0.762 | – | – |
PVCCIO_LL | 0.079 | – | – |
PVCCIO_LL_SNUB | OL | – | – |
PVCCIO_PGOOD | 0.550 | – | – |
PVCCIO_PHASE | 0.076 | – | 60.000R |
PVCCIO_VBST | 0.576 | – | – |
PVCCIOS0_AGND | 0.000 | – | – |
PVCCIOS0_CS_N | 0.076 | – | – |
PVCCIOS0_CS_P | 0.076 | – | – |
PVCCIOS0_EN | 0.782 | – | – |
PVCCIOS0_EN_FILT | 0.752 | – | – |
PVCCIOS0_EN_FILT_BUF | 0.552 | – | – |
PVCCIOS0_EN_R | 0.800 | – | – |
PVCCIOS0_FB | 0.538 | – | – |
PVCCIOS0_FSEL | 0.555 | – | – |
PVCCIOS0_RTN | 0.542 | – | – |
PVCCIOS0_SREF | 0.552 | – | – |
PVCCIOS0_VO | 0.547 | – | – |
PVCCOIOS0_OCSET | 0.548 | – | – |
PVCCPLLOC_EN | 0.533 | – | – |
PVCCPRIMCORE_FB | 0.130 | – | – |
PVCCPRIMCORE_FB_R | 0.131 | – | – |
PVCCPRIMCORE_SW0 | 0.073 | 1,050 | 143.000 |
PVCCPRIMCORE_SW1 | 0.073 | 1,050 | 143.000 |
PVCORE_GPU_FB_SNS_N | 0.000 | – | – |
PVCORE_GPU_FB_SNS_P | 0.000 | – | – |
PVDDCI_GPU_FB_SNS_N | 0.000 | – | – |
PVDDCI_GPU_FB_SNS_P | 0.036 | – | 35.020R |
PVDDCI_PGOOD | 0.555 | – | – |
PVDDCPUAWAKE_FB | 0.011 | – | 16.700R |
PVDDCPUAWAKE_FB_R | 0.018 | – | 17.000R |
PVDDCPUAWAKE_SW0 | 0.019 | 0,625 | 19,000R |
PVDDCPUAWAKE_SW1 | 0.019 | 0,625 | 19,000R |
PVDDCPUAWAKE_SW2 | 0.019 | 0,625 | 19,000R |
PVDDCPUAWAKE_SW3 | 0.019 | 0,625 | 19.000R |
PVDDCPUSRAMAWAKE_SW0 | 0.416 | 1,000 | 411.000 |
PVDDQ_EN | 0.739 | – | – |
PVDDQ_EN_LED | OL | – | – |
PVDDQ_EN_R | 0.503 | – | – |
PVDDQ_PGOOD | 0.504 | – | – |
PVIN_RFLDO_WLANBT_VLX | 0.347 | – | – |
PVPP_EN_R | 0.738 | – | – |
PVTT_VTTSNS | 0.126 | – | – |
REG_BOOT_GPU_VDDCI | 0.508 | – | – |
REG_BOOT_GPU_VDDCI_RC | 0.510 | – | – |
REG_FB_P1V8GPU | 1.415 | – | – |
REG_FB_P2V5S3 | 1.414 | – | – |
REG_GPU_VDDCI_COMP | 0.607 | – | – |
REG_GPU_VDDCI_FB | 0.503 | – | – |
REG_GPU_VDDCI_FB_R | OL | – | – |
REG_GPU_VDDCI_FB2_R | OL | – | – |
REG_GPU_VDDCI_FCCM | 0.624 | – | – |
REG_GPU_VDDCI_IMON | 0.635 | – | – |
REG_GPU_VDDCI_ISEN1 | 0.632 | – | – |
REG_GPU_VDDCI_ISUMN | 0.502 | – | – |
REG_GPU_VDDCI_ISUMP | 0.583 | – | – |
REG_GPU_VDDCI_VSEN | 0.037 | – | 35.800R |
REG_GPU_VDDCI_VSUMN | 0.035 | 0,900 | – |
REG_GPU_VDDCI_VSUMN_R | 0.037 | – | 358.000R |
REG_GPU_VDDCI_VSUMP | 0.035 | 0,900 | – |
REG_LGATE_GPU_VDDCI | 0.469 | – | – |
REG_PHASE_1V8GPU | 0.277 | – | 280.000R |
REG_PHASE_2V5S3 | 0.360 | 2,500 | 500.000R |
REG_PHASE_GPU_VDDCI | 0.036 | – | – |
REG_SNUBBER_GPU_VDDCI | OL | – | – |
REG_SSTR_P1V8GPU | 0.755 | – | – |
REG_SSTR_P2V5S3 | 0.755 | – | – |
REG_UGATE_GPU_VDDCI | 0.522 | – | – |
REG_UGATE_GPU_VDDCI_R | 0.522 | – | – |
REG_VOS_P1V8GPU | 0.280 | – | – |
REG_VOS_P2V5S3 | 0.368 | – | – |
RTN_A_CPUCORE | 0.000 | – | – |
RTN_B_CPUGT | 0.000 | – | – |
RTN_C_CPUSA | 0.000 | – | – |
SA_ISUMN_R | 1.027 | – | – |
SAVE_BAT_G | 0.775 | – | – |
SAVE_BAT_S | 1.568 | – | – |
SAVE_XA_CC1_G | 0.801 | – | – |
SAVE_XA_CC2_G | 0.802 | – | – |
SAVE_XA_CC2_Z | OL | – | – |
SAVE_XB_CC1_B | OL | – | – |
SAVE_XB_CC1_G | 0.863 | – | – |
SAVE_XB_CC1_Z | OL | – | – |
SAVE_XB_CC2_B | OL | – | – |
SAVE_XB_CC2_G | 0.838 | – | – |
SAVE_XB_CC2_Z | OL | – | – |
SE_CTLR_FW_DWLD | 0.478 | – | – |
SE_DEV_WAKE | 0.481 | – | – |
SE_PWR_EN | 0.740 | – | – |
SENSOR_PWR_EN | 0.718 | – | – |
SEP_CAM_DISABLE_DFF_L | 0.514 | – | – |
SEP_CAM_DISABLE_DFF_R_L | 0.511 | – | – |
SEP_CAM_DISABLE_L | 0.479 | – | – |
SEP_DISABLE_STROBE | 0.483 | – | – |
SEP_DMIC_DISABLE_L | 0.481 | – | – |
SEP_DMIC_DISABLE_Q_L | 0.669 | – | – |
SMBUS_3V3_BATT_SCL | 0.94 | – | – |
SMBUS_3V3_BATT_SDA | 0.96 | – | – |
SMBUS_PCH_CLK | 0.822 | – | – |
SMBUS_PCH_DATA | 0.822 | – | – |
SMC_BMON_ISENSE | 0.809 | – | – |
SMC_DCIN_VSENSE | 0.809 | – | – |
SMC_DEBUGPRT_RX | 0.492 | – | – |
SMC_DEBUGPRT_TX | 0.491 | – | – |
SMC_FAN_0_PWM | 0.45 | – | – |
SMC_FAN_0_TACH | 0.45 | 1.800 | – |
SMC_FAN_1_PWM | 0.492 | – | – |
SMC_FAN_1_TACH | 0.45 | 1.800 | – |
SMC_FIXTURE_MODE_L | 0.492 | – | – |
SMC_GPU_THRMTRIP | 0.488 | – | – |
SMC_LID_LEFT | 0.657 | – | – |
SMC_LID_RIGHT | 0.646 | – | – |
SMC_P3V3_CAPLE_ISENSE | 0.809 | – | – |
SMC_PBUS_VSENSE | 0.809 | – | – |
SMC_PCH_PWROK | 0.469 | – | – |
SMC_PCH_SYS_PWROK | 0.465 | – | – |
SMC_PECI_RX | 0.463 | – | – |
SMC_PECI_TX | 0.474 | – | – |
SMC_PECI_TX_R | 0.457 | – | – |
SMC_PROCHOT_L | 0.471 | – | – |
SMC_RSMRST_L | 0.459 | – | – |
SMC_SYSRST_L | 0.466 | – | – |
SMCRST_TIEOFF | 0.721 | – | – |
SOC_AMBER_DFU | OL | – | – |
SOC_AMBER_R | OL | – | – |
SOC_BLUE_AWAKE | 0.451 | – | – |
SOC_BLUE_R | OL | – | – |
SOC_CLKREQ_L | 0.812 | – | – |
SOC_COLD_RESET_L | 0.430 | – | – |
SOC_DEBUGPRT_RX | 0.482 | – | – |
SOC_DEBUGPRT_TX | 0.483 | – | – |
SOC_DFU_STATUS | 0.480 | – | – |
SOC_DOCK_CONNECT | 0.490 | – | – |
SOC_FORCE_DFU | 0.480 | – | – |
SOC_GPU_THRMTRIP | 0.686 | – | – |
SOC_GREEN_DDR | OL | – | – |
SOC_GREEN_R | OL | – | – |
SOC_HOLD_RESET | 0.471 | – | – |
SOC_JTAG_SEL | 0.492 | – | – |
SOC_PERST_L | 0.493 | – | – |
SOC_PM_THRMTRIP_L | 0.772 | – | – |
SOC_PM_THRMTRIP_L_R | 0.689 | – | – |
SOC_RED_R | OL | – | – |
SOC_RED_SLPS2R | OL | – | – |
SOC_SOCHOT_L | 0.483 | – | – |
SOC_SWD_MUX_SEL_PCH | 0.622 | – | – |
SOC_TESTMODE | 0.482 | – | – |
SOC_USB_VBUS | 0.683 | – | – |
SOC_VDDCPU_SENSE | 0.019 | – | 18.700R |
SOC_WDOG | 0.494 | – | – |
SPI_ACCEL_CS_L | 0.496 | – | – |
SPI_AOP_SENSOR_CLK | 0.515 | – | – |
SPI_AOP_SENSOR_MISO | 0.493 | – | – |
SPI_AOP_SENSOR_MISO_R | 0.515 | – | – |
SPI_AOP_SENSOR_MOSI | 0.515 | – | – |
SPI_DFR_CLK | 0.48 | – | – |
SPI_DFR_CS_L | 0.46 | – | – |
SPI_DFR_MISO | 0.493 | – | – |
SPI_DFR_MISO_R | 0.47 | – | – |
SPI_DFR_MOSI | 0.47 | – | – |
SPI_IO<2> | 0.799 | – | – |
SPI_IO<3> | 0.802 | – | – |
SPI_IO2_STRAP_L | 0.740 | – | – |
SPI_MESA_CLK_CONN | 0.52 | – | – |
SPI_MESA_MISO | 0.484 | – | – |
SPI_MESA_MISO_CONN | 0.45 | – | – |
SPI_MESA_MOSI_CONN | 0.47 | – | – |
SPI_MOSI_R | 0.807 | – | – |
SPI_MOSI_R_CONN | 1.108 | – | – |
SPI_SOCROM_CLK | 0.496 | – | – |
SPI_SOCROM_CS_L | 0.486 | – | – |
SPI_SOCROM_MISO_R | 0.391 | – | – |
SPI_SOCROM_MOSI | 0.486 | – | – |
SPI_SOCROM_WP_L | OL | – | – |
SPI_TPAD_CS_L | 0.451 | – | – |
SPI_TPAD_MISO | 0.447 | – | – |
SPI_TPAD_MISO_R | 0.440 | – | – |
SPI_TPAD3V3_CLK | 0.68 | – | – |
SPI_TPAD3V3_CLK_R | 0.458 | – | – |
SPI_TPAD3V3_CS_L | 0.66 | – | – |
SPI_TPAD3V3_MISO | 0.66 | – | – |
SPI_TPAD3V3_MOSI | 0.68 | – | – |
SPI_TPAD3V3_MOSI_R | 0.486 | – | – |
SPIROM_USE_MLB | 0.828 | – | – |
SPKR_ID0 | 0.485 | – | – |
SPKRAMP_INT_L | 0.370 | – | – |
SPKRAMP_LT_AREG | 0.588 | – | – |
SPKRAMP_LT_BSTN | 0.779 | – | – |
SPKRAMP_LT_BSTP | 0.779 | – | – |
SPKRAMP_LT_DREG | 0.530 | – | – |
SPKRAMP_LT_MODE | 0.000 | – | – |
SPKRAMP_LT_OUTN | 0.533 | – | – |
SPKRAMP_LT_OUTP | 0.533 | – | – |
SPKRAMP_LW_AREG | 0.587 | – | – |
SPKRAMP_LW_BSTN | 0.779 | – | – |
SPKRAMP_LW_BSTP | 0.779 | – | – |
SPKRAMP_LW_DREG | 0.527 | – | – |
SPKRAMP_LW_MODE | 0.405 | – | – |
SPKRAMP_LW_OUTN | 0.533 | – | – |
SPKRAMP_LW_OUTP | 0.533 | – | – |
SPKRAMP_RESET_L | 0.368 | – | – |
SPKRAMP_RT_DREG | 0.532 | – | – |
SPKRAMP_RT_MODE | 0.460 | – | – |
SPKRAMP_RT_OUTN | 0.525 | – | – |
SPKRAMP_RT_OUTP | 0.520 | – | – |
SPKRAMP_RW_AREG | 0.592 | – | – |
SPKRAMP_RW_BSTN | 0.779 | – | – |
SPKRAMP_RW_BSTP | 0.779 | – | – |
SPKRAMP_RW_DREG | 0.531 | – | – |
SPKRAMP_RW_MODE | 0.466 | – | – |
SPKRAMP_RW_OUTN | 0.520 | – | – |
SPKRAMP_RW_OUTP | 0.520 | – | – |
SPKRCONN_LT_OUTN | 0.533 | – | – |
SPKRCONN_LT_OUTP | 0.533 | – | – |
SPKRCONN_LW_OUTN | 0.533 | – | – |
SPKRCONN_LW_OUTP | 0.533 | – | – |
SPKRCONN_RT_OUTN | 0.525 | – | – |
SPKRCONN_RT_OUTP | 0.517 | – | – |
SPKRCONN_RW_OUTN | 0.520 | – | – |
SPKRCONN_RW_OUTP | 0.520 | – | – |
SPROM_CLK | 0.508 | – | – |
SPROM_CS | 0.504 | – | – |
SPROM_DIN | 0.512 | – | – |
SPROM_DOUT | 0.512 | – | – |
SSD_BFH | 0.430 | – | – |
SSD_PMU_RESET_L | 0.473 | – | – |
SSD0_CLKREQ0_L | 0.461 | – | – |
SSD0_CLKREQ1_L | 0.453 | – | – |
SSD0_CLKREQ2_L | 0.452 | – | – |
SSD0_CLKREQ3_L | 0.463 | – | – |
SSD0_OCARINA_FORCE_EN | 0.584 | – | – |
SSD0_OCARINA_NAND_VCC_DET | 0.763 | – | – |
SSD0_OCARINA_PGOOD | 0.764 | – | – |
SSD0_OCARINA_POK2 | 0.000 | – | – |
SSD0_OCARINA_RESET_L | 0.438 | – | – |
SSD0_OCARINA_TCAL | 0.776 | – | – |
SSD0_OCARINA_VDD_LDO | 0.368 | – | – |
SSD0_OCARINA_VREF | 0.772 | – | – |
SSD0_OCARINA_WP_L | 0.522 | – | – |
SSD0_PCIE_RESET_L | 0.428 | – | – |
SSD0_S4E_JTAG_SEL | 0.439 | – | – |
SSD0_S4E_JTAG_TRST_L | 0.440 | – | – |
SSD0_S4E0_DROOP_L | 0.505 | – | – |
SSD0_S4E0_JTAG_TDI | 0.499 | – | – |
SSD0_S4E0_JTAG_TDO | 0.466 | – | – |
SSD0_S4E0_PCIE_RESREF | 0.786 | – | – |
SSD0_S4E0_UART_TX | 0.496 | – | – |
SSD0_S4E0_VPP | 0.550 | – | – |
SSD0_S4E0_ZQ_C | 0.101 | – | – |
SSD0_S4E0_ZQ_L | 0.303 | – | – |
SSD0_S4E1_DROOP_L | 0.489 | – | – |
SSD0_S4E1_JTAG_TDO | 0.460 | – | – |
SSD0_S4E1_PCIE_RESREF | 0.789 | – | – |
SSD0_S4E1_UART_TX | 0.479 | – | – |
SSD0_S4E1_VPP | 0.553 | – | – |
SSD0_S4E1_ZQ_C | 0.101 | – | – |
SSD0_S4E1_ZQ_L | 0.303 | – | – |
SSD0_S4E2_DROOP_L | 0.483 | – | – |
SSD0_S4E2_JTAG_TDO | 0.468 | – | – |
SSD0_S4E2_PCIE_RESREF | 0.787 | – | – |
SSD0_S4E2_UART_TX | 0.479 | – | – |
SSD0_S4E2_VPP | 0.552 | – | – |
SSD0_S4E2_ZQ_C | 0.102 | – | – |
SSD0_S4E2_ZQ_L | 0.304 | – | – |
SSD0_S4E3_DROOP_L | 0.509 | – | – |
SSD0_S4E3_JTAG_TDO | 0.504 | – | – |
SSD0_S4E3_PCIE_RESREF | 0.786 | – | – |
SSD0_S4E3_UART_TX | 0.505 | – | – |
SSD0_S4E3_VPP | 0.550 | – | – |
SSD0_S4E3_ZQ_C | 0.102 | – | – |
SSD0_S4E3_ZQ_L | 0.305 | – | – |
SSD0_STG01_ADDR | 0.582 | – | – |
SSD0_SWCLK_UART_R2D | 0.437 | – | – |
SSD0_SWDIO_UART_D2R | 0.433 | – | – |
SSD0_TPS62180_FB | 1.411 | – | – |
SSD0_TPS62180_FB_R | 0.376 | – | – |
SSD0_TPS62180_SS | 0.540 | – | – |
SSD0_VR_P2V5_EN | 0.650 | – | – |
SSD0_VR_P2V5_EN_R | 0.651 | – | – |
SSD0_VR_P2V5_PGOOD | 0.575 | – | – |
SSD1_CLK24M | OL | – | – |
SSD1_CLKREQ0_L | OL | – | – |
SSD1_CLKREQ1_L | 0.491 | – | – |
SSD1_CLKREQ2_L | 0.490 | – | – |
SSD1_CLKREQ3_L | OL | – | – |
SSD1_OCARINA_FORCE_EN | OL | – | – |
SSD1_OCARINA_IREF | OL | – | – |
SSD1_OCARINA_NAND_VCC_DET | OL | – | – |
SSD1_OCARINA_PGOOD | OL | – | – |
SSD1_OCARINA_POK2 | OL | – | – |
SSD1_OCARINA_RESET_L | OL | – | – |
SSD1_OCARINA_TCAL | OL | – | – |
SSD1_OCARINA_VDD_LDO | OL | – | – |
SSD1_OCARINA_VREF | OL | – | – |
SSD1_OCARINA_WP_L | OL | – | – |
SSD1_PCIE_RESET_L | 0.476 | – | – |
SSD1_S4E_JTAG_SEL | OL | – | – |
SSD1_S4E_JTAG_TRST_L | OL | – | – |
SSD1_S4E0_JTAG_TDI | OL | – | – |
SSD1_S4E0_JTAG_TDO | OL | – | – |
SSD1_S4E0_PCIE_RESREF | OL | – | – |
SSD1_S4E0_UART_TX | OL | – | – |
SSD1_S4E0_VPP | OL | – | – |
SSD1_S4E0_ZQ_C | OL | – | – |
SSD1_S4E0_ZQ_L | OL | – | – |
SSD1_S4E1_JTAG_TDO | OL | – | – |
SSD1_S4E1_PCIE_RESREF | OL | – | – |
SSD1_S4E1_UART_TX | OL | – | – |
SSD1_S4E1_VPP | OL | – | – |
SSD1_S4E1_ZQ_C | OL | – | – |
SSD1_S4E1_ZQ_L | OL | – | – |
SSD1_S4E2_JTAG_TDO | OL | – | – |
SSD1_S4E2_PCIE_RESREF | OL | – | – |
SSD1_S4E2_UART_TX | OL | – | – |
SSD1_S4E2_VPP | OL | – | – |
SSD1_S4E2_ZQ_C | OL | – | – |
SSD1_S4E2_ZQ_L | OL | – | – |
SSD1_S4E3_JTAG_TDO | OL | – | – |
SSD1_S4E3_PCIE_RESREF | OL | – | – |
SSD1_S4E3_UART_TX | OL | – | – |
SSD1_S4E3_VPP | OL | – | – |
SSD1_S4E3_ZQ_C | OL | – | – |
SSD1_S4E3_ZQ_L | OL | – | – |
SSD1_TPS62180_FB | OL | – | – |
SSD1_TPS62180_SS | OL | – | – |
SSD1_VR_P2V5_EN | OL | – | – |
SSD1_VR_P2V5_EN_R | OL | – | – |
SSD1_VR_P2V5_PGOOD | OL | – | – |
SSTATE_BLUE | OL | – | – |
SSTATE_BLUE_R | OL | – | – |
SSTATE_GREEN | OL | – | – |
SSTATE_GREEN_R | OL | – | – |
SSTATE_RED | OL | – | – |
SSTATE_RED_R | OL | – | – |
SWD_SOC_SWCLK | 0.489 | – | – |
SWD_SOC_SWDIO | 0.490 | – | – |
SYS_DETECT | OL | – | – |
SYS_DETECT_L | 0.55 | – | – |
TBT_POC_RESET | 0.66 | – | – |
TBT_PWR_EN | 0.745 | – | – |
TBT_PWR_EN_U8295 | 0.574 | – | – |
TBT_PWR_EN_U8297 | 0.575 | – | – |
TBT_T_BATLOW_L | 0.600 | – | – |
TBT_T_CIO_PWR_EN | 0.57 | – | – |
TBT_T_CLKREQ_L | 0.810 | – | – |
TBT_T_CLKREQ_R_L | 0.601 | – | – |
TBT_T_HDMI_DDC_CLK | 0.601 | – | – |
TBT_T_HDMI_DDC_DATA | 0.601 | – | – |
TBT_T_PCI_RESET_L | 0.595 | – | – |
TBT_T_RBIAS | 0.781 | – | – |
TBT_T_ROM_HOLD_L | 0.708 | – | – |
TBT_T_ROM_WP_L | 0.592 | – | – |
TBT_T_RSENSE | 0.000 | – | – |
TBT_T_RTD3_PWR_EN | 0.599 | – | – |
TBT_T_SPI_CLK | 0.570 | – | – |
TBT_T_SPI_CLK_DBG | 0.64 | – | – |
TBT_T_SPI_CS_L | 0.601 | – | – |
TBT_T_SPI_MISO | 0.602 | – | – |
TBT_T_SPI_MOSI | 0.606 | – | – |
TBT_T_TEST_EN | 0.100 | – | – |
TBT_T_TEST_PWR_GOOD | 0.101 | – | – |
TBT_T_TMU_CLK_IN | 0.603 | – | – |
TBT_T_USB_PWR_EN | 0.57 | – | – |
TBT_T_XTAL25M_IN | 0.840 | – | – |
TBT_T_XTAL25M_OUT | 0.792 | – | – |
TBT_TA_LSRX | 0.774 | – | – |
TBT_TA_USB2_MXCTL | 0.601 | – | – |
TBT_TA_USB2_RBIAS | 0.210 | – | – |
TBT_TB_USB2_MXCTL | 0.598 | – | – |
TBT_TB_USB2_RBIAS | 0.202 | – | – |
TBT_WAKE_3V3_L | 0.57 | – | – |
TBT_X_CIO_PWR_EN | 0.58 | – | – |
TBT_X_HDMI_DDC_CLK | 0.601 | – | – |
TBT_X_HDMI_DDC_DATA | 0.600 | – | – |
TBT_X_PCI_RESET_L | 0.59 | – | – |
TBT_X_PCIE_BIAS | 0.792 | – | – |
TBT_X_PLUG_EVENT_L | 0.59 | – | – |
TBT_X_RBIAS | 0.782 | – | – |
TBT_X_ROM_HOLD_L | 0.708 | – | – |
TBT_X_ROM_WP_L | 0.591 | – | – |
TBT_X_RSENSE | 0.001 | – | 0.600R |
TBT_X_RTD3_PWR_EN | 0.598 | – | – |
TBT_X_SPI_CLK | 0.567 | – | – |
TBT_X_SPI_CLK_DBG | 0.65 | – | – |
TBT_X_SPI_CS_L | 0.599 | – | – |
TBT_X_SPI_MISO | 0.602 | – | – |
TBT_X_SPI_MOSI | 0.604 | – | – |
TBT_X_TEST_EN | 0.100 | – | – |
TBT_X_TEST_PWR_GOOD | 0.100 | – | – |
TBT_X_TMU_CLK_IN | 0.601 | – | – |
TBT_X_TMU_CLK_OUT | 0.600 | – | – |
TBT_X_USB_PWR_EN | 0.58 | – | – |
TBT_X_XTAL25M_IN | 0.838 | – | – |
TBT_X_XTAL25M_OUT | 0.790 | – | – |
TBT_XA_LSRX | 0.537 | – | – |
TBT_XA_LSTX | 0.815 | – | – |
TBT_XB_LSRX | 0.788 | – | – |
TBT_XB_LSTX | 0.80 | – | – |
TBTTHMSNS_T_D1_N | 0.000 | – | – |
TBTTHMSNS_T_D1_P | 0.653 | – | – |
TBTTHMSNS_X_D1_N | 0.000 | – | – |
TBTTHMSNS_X_D1_P | 0.652 | – | – |
TP_BKLT_BOOST_EN | 0.618 | – | – |
TP_BKLT_FAULT_L | 0.614 | – | – |
TP_BMON_IOUT | OL | – | – |
TP_BT_JTAG_STRAP | 0.728 | – | – |
TP_CHGR_EN_VR1 | 0.61 | – | – |
TP_CHGR_SMC_RST_L | 0.60 | – | – |
TP_CPU_RSVD_TP_BT2 | 0.340 | – | – |
TP_CPU_RSVD_TP_D1 | 0.243 | – | – |
TP_CPU_RSVD_TP75 | 0.335 | – | – |
TP_CPU_RSVD_TP76 | 0.242 | – | – |
TP_DFR_TOUCH_PANEL_DETECT | OL | – | – |
TP_DFR_TOUCH_ROM_WC | OL | – | – |
TP_DFR_TOUCH_RSVD | OL | – | – |
TP_GPUVCORE_IMON | 0.635 | – | – |
TP_HDA_RST | 0.823 | – | – |
TP_HDA_SDI1 | 0.823 | – | – |
TP_HDA_SDO | 0.823 | – | – |
TP_JTAG_SOC_TRST_L | 0.494 | – | – |
TP_PCH_SLP_SUS_L | 0.817 | – | – |
TP_PCH_STRP_BOOT_SPI_L | 0.828 | – | – |
TP_PCH_STRP_TLSCONF | 0.829 | – | – |
TP_PCH_STRP_TOPBLK_SWP_L | 0.829 | – | – |
TP_PCH_TP1_F22 | 0.787 | – | – |
TP_PCH_TP3_B24 | 0.838 | – | – |
TP_Q3100_DRAIN | 0.59 | – | – |
TP_Q3200_DRAIN | 0.675 | – | – |
TP_SSD0_S4E0_ANI0_VREF | 0.591 | – | – |
TP_SSD0_S4E0_ANI1_VREF | 0.591 | – | – |
TP_SSD0_S4E1_ANI0_VREF | 0.592 | – | – |
TP_SSD0_S4E1_ANI1_VREF | 0.592 | – | – |
TP_SSD0_S4E2_ANI0_VREF | 0.591 | – | – |
TP_SSD0_S4E2_ANI1_VREF | 0.592 | – | – |
TP_SSD0_S4E3_ANI0_VREF | 0.591 | – | – |
TP_SSD0_S4E3_ANI1_VREF | 0.591 | – | – |
TP_SSD1_S4E0_ANI0_VREF | OL | – | – |
TP_SSD1_S4E0_ANI1_VREF | OL | – | – |
TP_SSD1_S4E1_ANI0_VREF | OL | – | – |
TP_SSD1_S4E1_ANI1_VREF | OL | – | – |
TP_SSD1_S4E2_ANI0_VREF | OL | – | – |
TP_SSD1_S4E2_ANI1_VREF | OL | – | – |
TP_SSD1_S4E3_ANI0_VREF | OL | – | – |
TP_SSD1_S4E3_ANI1_VREF | OL | – | – |
TP_UPC_TA_SWD_CLK | 0.748 | – | – |
TP_UPC_TA_SWD_DATA | 0.747 | – | – |
TP_UPC_TB_SWD_CLK | 0.748 | – | – |
TP_UPC_TB_SWD_DATA | 0.749 | – | – |
TP_UPC_XA_SWD_CLK | 0.751 | – | – |
TP_UPC_XA_SWD_DATA | 0.751 | – | – |
TP_UPC_XB_SWD_CLK | 0.73 | – | – |
TP_UPC_XB_SWD_DATA | 0.73 | – | – |
TP_USBC_PP20V_TA | OL | – | – |
TP_USBC_PP20V_TB | OL | – | – |
TP_USBC_PP20V_XA | OL | – | – |
TP_USBC_PP20V_XB | OL | – | – |
TP_USBC_TB_RESET_L | 0.778 | – | – |
TP_USBC_XA_RESET_L | 0.780 | – | – |
TP_WLAN_PMU_TEST | 0.000 | – | – |
TPAD_ACTUATOR_DISABLE_L | 0.495 | – | – |
TPAD_KBD_WAKE_L | 0.45 | – | – |
TPAD_SPI_EN | 0.481 | – | – |
TPAD_SPI_INT_L | 0.45 | – | – |
TPAD3V3_ACTUATOR_DISABLE_L | 0.84 | – | – |
TPAD3V3_SPI_EN | 0.66 | – | – |
TPAD3V3_SPI_INT_L | 0.85 | – | – |
TSNS_T1_DN | 0.000 | – | – |
TSNS_T1_DX1_N | 0.000 | – | – |
TSNS_T1_DX1_P | 0.639 | – | – |
TSNS_T1_DX2_N | 0.000 | – | – |
TSNS_T1_DX2_P | 0.640 | – | – |
TSNS_T1_DX3_N | 0.000 | – | – |
TSNS_T1_DX3_P | 0.642 | – | – |
TSNS_T1_DX4_P | 0.640 | – | – |
TSNS_T1_DX5_N | 0.000 | – | – |
TSNS_T1_DX5_P | 0.641 | – | – |
TSNS_T1_DX6_N | 0.000 | – | 1.300R |
TSNS_T1_DX6_P | 0.643 | – | – |
TSNS_T1_DX7_P | 0.640 | – | – |
U4800_PIN4 | 0.707 | – | – |
UART_BT_D2R | 0.476 | – | – |
UART_BT_D2R_CTS_L | 0.477 | – | – |
UART_BT_LH_D2R | 0.000 | – | – |
UART_BT_MUX_CTS_L | 0.641 | – | – |
UART_BT_MUX_D2R | 0.647 | – | – |
UART_BT_MUX_R2D | 0.645 | – | – |
UART_BT_MUX_RTS_L | 0.645 | – | – |
UART_BT_R2D | 0.477 | – | – |
UART_BT_R2D_RTS_L | 0.474 | – | – |
UART_SE_D2R | 0.484 | – | – |
UART_SE_D2R_CTS_L | 0.483 | – | – |
UART_SE_R2D | 0.485 | – | – |
UART_SE_R2D_RTS_L | 0.485 | – | – |
UART_WLAN_D2R | 0.486 | – | – |
UART_WLAN_D2R_CTS_L | 0.485 | – | – |
UART_WLAN_R2D | 0.485 | – | – |
UART_WLAN_R2D_RTS_L | 0.483 | – | – |
UNCONNECTED_14 | OL | – | – |
UNCONNECTED_15 | OL | – | – |
UNCONNECTED_188 | OL | – | – |
UNCONNECTED_189 | OL | – | – |
UNCONNECTED_190 | OL | – | – |
UPC_I2C_INT_L | 0.45 | – | – |
UPC_PMU_RESET | 0.716 | – | – |
UPC_T_5V_EN | 0.704 | – | – |
UPC_T_5V_EN_R | 0.554 | – | – |
UPC_T_SPI_CLK | 0.594 | – | – |
UPC_T_SPI_CS_L | 0.591 | – | – |
UPC_T_SPI_MISO | 0.593 | – | – |
UPC_T_SPI_MOSI | 0.568 | – | – |
UPC_TA_DBG3 | 0.778 | – | – |
UPC_TA_DBG4 | 0.778 | – | – |
UPC_TA_FAULT_L | 0.762 | – | – |
UPC_TA_GATE1 | 0.659 | – | – |
UPC_TA_GATE2 | 0.659 | – | – |
UPC_TA_GPIO0 | 0.774 | – | – |
UPC_TA_GPIO1 | 0.772 | – | – |
UPC_TA_R_OSC | 0.539 | – | – |
UPC_TA_SPI_CLK | 0.584 | – | – |
UPC_TA_SPI_CS_L | 0.617 | – | – |
UPC_TA_SPI_MISO | 0.619 | – | – |
UPC_TA_SPI_MOSI | 0.621 | – | – |
UPC_TA_SS | 0.533 | – | – |
UPC_TA_UART_RX | 0.74 | – | – |
UPC_TA_UART_TX | 0.75 | – | – |
UPC_TB_DBG3 | 0.778 | – | – |
UPC_TB_DBG4 | 0.778 | – | – |
UPC_TB_FAULT_L | 0.762 | – | – |
UPC_TB_GATE1 | 0.659 | – | – |
UPC_TB_GATE2 | 0.651 | – | – |
UPC_TB_GPIO0 | 0.775 | – | – |
UPC_TB_GPIO1 | 0.773 | – | – |
UPC_TB_GPIO7 | 0.775 | – | – |
UPC_TB_R_OSC | 0.536 | – | – |
UPC_TB_SS | 0.533 | – | – |
UPC_X_5V_EN | 0.705 | – | – |
UPC_X_5V_EN_R | 0.558 | – | – |
UPC_X_SPI_CS_L | 0.591 | – | – |
UPC_XA_DBG1 | 0.573 | – | – |
UPC_XA_FAULT_L | 0.755 | – | – |
UPC_XA_GATE1 | 0.64 | – | – |
UPC_XA_GATE2 | 0.63 | – | – |
UPC_XA_GPIO0 | 0.777 | – | – |
UPC_XA_R_OSC | 0.787 | – | – |
UPC_XA_SS | 0.530 | – | – |
UPC_XA_UART_RX | 0.75 | – | – |
UPC_XA_UART_TX | 0.74 | – | – |
UPC_XB_DBG3 | 0.494 | – | – |
UPC_XB_DBG4 | 0.495 | – | – |
UPC_XB_FAULT_L | 0.74 | – | – |
UPC_XB_GATE2 | 0.654 | – | – |
UPC_XB_GPIO0 | 0.76 | – | – |
UPC_XB_GPIO1 | 0.76 | – | – |
UPC_XB_R_OSC | 0.53 | – | – |
UPC_XB_SPI_CLK | 0.58 | – | – |
UPC_XB_SPI_CS_L | 0.61 | – | – |
UPC_XB_SPI_MISO | 0.61 | – | – |
UPC_XB_SPI_MOSI | 0.61 | – | – |
UPC_XB_SS | 0.53 | – | – |
USB_DBG_PCH_XA_F_N | 0.520 | – | – |
USB_DBG_PCH_XA_F_P | 0.520 | – | – |
USB_SOC_N | 0.727 | – | – |
USB_SOC_P | 0.727 | – | – |
USB_SOC_TYPEC_N | 0.722 | – | – |
USB_SOC_TYPEC_P | 0.722 | – | – |
USB_UPC_TA_F_N | 0.522 | – | – |
USB_UPC_TA_F_P | 0.517 | – | – |
USB_UPC_TB_F_N | 0.511 | – | – |
USB_UPC_TB_F_P | 0.515 | – | – |
USB_UPC_XA_N | 0.755 | – | – |
USB_UPC_XA_P | 0.755 | – | – |
USB_UPC_XB_F_P | 0.44 | – | – |
USB2_UPC_TA_N | 0.522 | – | – |
USB2_UPC_TA_P | 0.517 | – | – |
USB2_UPC_TB_N | 0.511 | – | – |
USB2_UPC_TB_P | 0.515 | – | – |
USB2_UPC_XA_N | 0.520 | – | – |
USB2_UPC_XA_P | 0.520 | – | – |
USB2_UPC_XB_P | 0.44 | – | – |
USB3_EXTA_D2R_N | 0.360 | – | – |
USB3_EXTA_D2R_P | 0.358 | – | – |
USB3_EXTA_R2D_C_N | 0.341 | – | – |
USB3_EXTA_R2D_C_P | 0.343 | – | – |
USB3_EXTA_R2D_N | 0.738 | – | – |
USB3_EXTA_R2D_P | 0.739 | – | – |
USB3_TEST_D2R_N | 0.361 | – | – |
USB3_TEST_D2R_P | 0.361 | – | – |
USB3_TEST_R2D_N | 0.342 | – | – |
USB3_TEST_R2D_P | 0.343 | – | – |
USB3_TEST2_D2R_N | 0.363 | – | – |
USB3_TEST2_D2R_P | 0.361 | – | – |
USB3_TEST2_R2D_N | 0.340 | – | – |
USB3_TEST2_R2D_P | 0.340 | – | – |
USBC_HPD_DET | 0.604 | – | – |
USBC_T_RESET_L | 0.765 | – | – |
USBC_TA_CC1 | 0.611 | – | – |
USBC_TA_CC1_CONN | 0.812 | – | – |
USBC_TA_CC2 | 0.615 | – | – |
USBC_TA_CC2_CONN | 0.779 | – | – |
USBC_TA_D2R_CR_N<1> | OL | – | – |
USBC_TA_D2R_CR_N<2> | OL | – | – |
USBC_TA_D2R_CR_P<1> | OL | – | – |
USBC_TA_D2R_CR_P<2> | OL | – | – |
USBC_TA_R2D_N<1> | OL | – | – |
USBC_TA_R2D_N<2> | OL | – | – |
USBC_TA_R2D_P<1> | OL | – | – |
USBC_TA_R2D_P<2> | OL | – | – |
USBC_TA_SBU1 | 0.876 | – | – |
USBC_TA_SBU2 | OL | – | – |
USBC_TA_USB_BOT_N | OL | – | – |
USBC_TA_USB_BOT_P | OL | – | – |
USBC_TA_USB_TOP_N | 0.973 | – | – |
USBC_TA_USB_TOP_P | 0.910 | – | – |
USBC_TB_CC1 | 0.612 | – | – |
USBC_TB_CC1_CONN | 0.734 | – | – |
USBC_TB_CC2 | 0.616 | – | – |
USBC_TB_CC2_CONN | 0.821 | – | – |
USBC_TB_D2R_CR_N<1> | OL | – | – |
USBC_TB_D2R_CR_N<2> | OL | – | – |
USBC_TB_D2R_CR_P<1> | OL | – | – |
USBC_TB_D2R_CR_P<2> | OL | – | – |
USBC_TB_R2D_N<1> | OL | – | – |
USBC_TB_R2D_N<2> | OL | – | – |
USBC_TB_R2D_P<1> | OL | – | – |
USBC_TB_SBU1 | 0.887 | – | – |
USBC_TB_SBU2 | 0.847 | – | – |
USBC_TB_USB_BOT_N | OL | – | – |
USBC_TB_USB_BOT_P | OL | – | – |
USBC_TB_USB_TOP_N | 0.961 | – | – |
USBC_TB_USB_TOP_P | 0.959 | – | – |
USBC_X_RESET_L | 0.770 | – | – |
USBC_XA_CC1 | 0.614 | – | – |
USBC_XA_CC1_CONN | 0.943 | – | – |
USBC_XA_CC2 | 0.617 | – | – |
USBC_XA_CC2_CONN | 0.946 | – | – |
USBC_XA_D2R_CR_N<1> | OL | – | – |
USBC_XA_D2R_CR_N<2> | OL | – | – |
USBC_XA_D2R_CR_P<1> | OL | – | – |
USBC_XA_D2R_CR_P<2> | OL | – | – |
USBC_XA_R2D_N<1> | OL | – | – |
USBC_XA_R2D_N<2> | OL | – | – |
USBC_XA_R2D_P<1> | OL | – | – |
USBC_XA_R2D_P<2> | OL | – | – |
USBC_XA_SBU1 | 0.856 | – | – |
USBC_XA_SBU2 | 0.856 | – | – |
USBC_XA_USB_DBG_BOT_N | 0.316 | – | – |
USBC_XA_USB_DBG_BOT_P | 0.316 | – | – |
USBC_XA_USB_DBG_TOP_N | 0.315 | – | – |
USBC_XA_USB_DBG_TOP_P | 0.316 | – | – |
USBC_XB_CC1 | 0.59 | – | – |
USBC_XB_CC1_CONN | 0.971 | – | – |
USBC_XB_CC2 | 0.59 | – | – |
USBC_XB_CC2_CONN | 0.933 | – | – |
USBC_XB_D2R_CR_N<1> | OL | – | – |
USBC_XB_D2R_CR_N<2> | OL | – | – |
USBC_XB_D2R_CR_P<1> | OL | – | – |
USBC_XB_D2R_CR_P<2> | OL | – | – |
USBC_XB_R2D_N<1> | OL | – | – |
USBC_XB_R2D_N<2> | OL | – | – |
USBC_XB_R2D_P<1> | OL | – | – |
USBC_XB_R2D_P<2> | OL | – | – |
USBC_XB_SBU1 | 0.859 | – | – |
USBC_XB_SBU2 | 0.861 | – | – |
USBC_XB_USB_BOT_N | OL | – | – |
USBC_XB_USB_BOT_P | OL | – | – |
USBC_XB_USB_TOP_N | 0.975 | – | – |
USBC_XB_USB_TOP_P | 0.978 | – | – |
UVP_DIS_L | 0.560 | – | – |
VDDCIS0_CS_N | 0.033 | – | 31.900R |
VDDCIS0_CS_P | 0.032 | – | 31.600R |
VR_PHASE_GPU_VDDCI | 0.035 | 0,900 | 34.400R |
VR0V9_IND_TBT_T | 0.314 | 0,900 | 330.000R |
VR0V9_IND_TBT_X | 0.314 | 0,900 | – |
VRVDDCI_R | 0.035 | 0,900 | 34.400R |
WIFI_SROM_ORG | 0.707 | – | – |
WL_GPIO_13 | 0.655 | – | – |
WLAN_AUDIO_SYNC | 0.480 | – | – |
WLAN_AUDIO_SYNC_LS3V3 | 0.638 | – | – |
WLAN_CONTEXT_A | 0.490 | – | – |
WLAN_CONTEXT_B | 0.491 | – | – |
WLAN_HOST_WAKE | 0.489 | – | – |
WLAN_JTAG_SEL | 0.744 | – | – |
WLAN_JTAG_TCK | 0.490 | – | – |
WLAN_JTAG_TDI | 0.482 | – | – |
WLAN_JTAG_TDO | 0.478 | – | – |
WLAN_JTAG_TMS | 0.490 | – | – |
WLAN_JTAG_TRST_L | 0.756 | – | – |
WLAN_PWR_EN | 0.490 | – | – |
WLAN_SROM_STRAP | 0.744 | – | – |
XDP_BPM_L<0> | 0.283 | – | – |
XDP_BPM_L<1> | 0.281 | – | – |
XDP_BPM_L<2> | 0.281 | – | – |
XDP_BPM_L<3> | 0.283 | – | – |
XDP_CPU_PRDY_L | 0.254 | – | – |
XDP_CPU_PREQ_L | 0.273 | – | – |
XDP_CPU_PWRBTN_L | 0.778 | – | – |
XDP_CPU_TCK | 0.052 | – | 50.600R |
XDP_CPU_TDI | 0.235 | – | – |
XDP_CPU_TDO | 0.220 | – | – |
XDP_CPU_TMS | 0.235 | – | – |
XDP_CPU_TRST_L | 0.282 | – | – |
XDP_DBRESET_L | 0.814 | – | – |
XDP_JTAG_ISP_TCK | 0.564 | – | – |
XDP_JTAG_ISP_TDI | 0.563 | – | – |
XDP_JTAG_ISP_TDO | 0.566 | – | – |
XDP_PCH_JTAGX | 0.053 | – | 52.600R |
XDP_PCH_OBSDATA_A0 | 0.825 | – | – |
XDP_PCH_OBSDATA_A1 | 0.824 | – | – |
XDP_PCH_OBSDATA_A2 | 0.823 | – | – |
XDP_PCH_OBSDATA_A3 | 0.825 | – | – |
XDP_PCH_OBSDATA_B0 | 0.825 | – | – |
XDP_PCH_OBSDATA_B1 | 0.825 | – | – |
XDP_PCH_OBSDATA_B2 | 0.824 | – | – |
XDP_PCH_OBSDATA_B3 | 0.824 | – | – |
XDP_PCH_OBSDATA_D0 | 0.824 | – | – |
XDP_PCH_OBSDATA_D1 | 0.824 | – | – |
XDP_PCH_OBSFN_C0 | 0.824 | – | – |
XDP_PCH_TCK | 0.339 | – | – |
XDP_PCH_TDI | 0.236 | – | – |
XDP_PCH_TDO | 0.224 | – | – |
XDP_PCH_TMS | 0.236 | – | – |
XDP_PCH_TRST_L | 0.281 | – | – |
XDP_PM_RSMRST_L | 1.524 | – | – |
XDP_PRESENT_CPU | 1.771 | – | – |
XDP_PRESENT_L | 0.476 | – | – |
XDP_USB_EXTA_OC_L | 0.762 | – | – |
XDP_USB_EXTB_OC_L | 0.762 | – | – |
XDP_USB_EXTC_OC_L | 0.762 | – | – |
XDP_USB_EXTD_OC_L | 0.763 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PPBUS_G3H read on the 820-01814?
OpenBoardData's known-good values for PPBUS_G3H on the 820-01814: diode 0.434, voltage 12,600. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S5 read on the 820-01814?
OpenBoardData's known-good values for PP3V3_S5 on the 820-01814: diode 0.327. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP1V8_G3S read on the 820-01814?
OpenBoardData's known-good values for PP1V8_G3S on the 820-01814: diode 0.330, voltage 1.800. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-01814 board?
Open your own 820-01814 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License