Apple laptop board · OpenBoardData

820-2936 known-good readings

Known-good readings for the Apple laptop board 820-2936: 125 nets, including 33 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 32 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-2936.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 33 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 8

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.3383.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, indicated by the "G3H" suffix in its name (general naming convention, not from this board's data). Known-good readings from the archive: diode 0.338 to ground and 3.400 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode far from 0.338 suggests a short or leaky part on the rail; a voltage well below 3.400 V points to the rail not coming up or being loaded down. No known-good resistance reading is available here, so compare against a matching net or a known-good board.

PPBUS_G3H0.434––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the G3H suffix indicates it is always-on (from the name). The archive lists a known-good diode reading of 0.434 to ground for this rail; no known-good voltage reading is recorded here. Check it unpowered in diode mode from PPBUS_G3H to ground, then measure its voltage with power applied. A diode reading far below 0.434 usually points to a short or leaky part on the rail; far above can mean an open connection. These are community readings and only a guide, so compare against a matching rail or known-good board before condemning anything.

PPDCIN_G3H0.64516.730–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on DC input rail, as its G3H suffix indicates (from the name). Known-good readings in the archive: diode 0.645 to ground, and 16.730 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the charger connected. A diode reading far from 0.645 usually points to a short or leaky part on the rail, and a missing or low voltage points to the input path or charger side. No known-good resistance reading here, so compare against a matching net or a known-good board.

PPDCIN_G3H_CHGR0.604––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in its name marks it as an always-on rail, present whenever the charger is connected. The only known-good reading here is diode mode to ground: 0.604, with the board unpowered. Check it by measuring diode mode from the rail to ground with power off, then measure the DC voltage with the charger connected. No known-good voltage reading is recorded here, so compare against a known-good board or the charger's rated input. A diode reading far below 0.604 usually points to a short or leaky part on the rail; a much higher or open reading points to a broken connection feeding it. These are general guidelines, not confirmed causes.

PPDCIN_G3H_INRUSH_FETOL––
AI: what PPDCIN_G3H_INRUSH_FET is and how to check it

PPDCIN_G3H_INRUSH_FET — from the name, this is the inrush FET node on the PPDCIN (DC input) side of the G3H always-on rail: the point where the adapter input feeds through the inrush FET. It's present before the board is switched on.

  • Known-good reading (archive): diode mode to ground reads OL (open). Treat this as a guide only; it varies with board state.
  • How to check: power off and unplug the adapter, then measure diode mode from PPDCIN_G3H_INRUSH_FET to ground. Then apply power and measure the DC voltage on the same point.
  • No known-good voltage is recorded here for this net, so compare against a matching net or a known-good board rather than a fixed number.
  • A diode reading far from OL (a low value to ground) usually points to a short or leaky part on that node; a voltage that's missing with the adapter connected points upstream toward the input path. Neither confirms a bad part on one reading — check the next node before replacing anything.
PPVBAT_G3H_CHGR_R0.431––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is a battery-related rail; the G3H in its name indicates it is always on, and CHGR suggests it belongs to the charger section — both from the name only. The archive lists one known-good reading: diode 0.431 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.431 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.

PPVBAT_G3H_CHGR_REG0.431––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From its name, PPVBAT_G3H_CHGR_REG is a charger-side regulated rail tied to the battery supply, in the G3H always-on group. It's present whenever the charger is connected, before the main power sequence.
  • Known-good reading: Diode mode to ground, board unpowered, 0.431 (community archive value, a guide only). No known-good voltage reading here.
  • How to check: Power off and measure diode to ground on the rail, then apply power and measure the voltage. Compare the diode reading with 0.431.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. One reading alone doesn't confirm a bad part, so check the voltage next before replacing anything.
PPVBAT_G3H_CONNOL Con BateriaOL11.100 Con Bateria11.100–
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judged from its name; the "G3H" suffix indicates it is present whenever the battery is connected. The archive lists diode OL (Con Bateria) and voltage 11.100 V (Con Bateria), so those are the only known-good readings here. Check it unpowered in diode mode from the net to ground, then measure the voltage with the battery connected. A voltage far below 11.100 V points to a battery-side supply or connection problem rather than a short, since OL in diode mode is normal for this rail. No known-good resistance reading is recorded for this net.

S5 and SUS: standby 6

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.125––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply. The archive lists one known-good reading: diode 0.125 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching standby rail or a known-good board. A diode reading far from 0.125 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_SUS0.400––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail, judged from its name (SUS = suspend/standby), so it should be present whenever the board has standby power. The archive lists one known-good reading: diode mode to ground of 0.400, with no condition noted. Check it with the board unpowered in diode mode from PP3V3_SUS to ground, then measure the voltage with power applied. No known-good voltage reading is listed here. A diode value far below 0.400 usually points to a short or a leaky load on the rail; a value far above it can mean an open trace or missing connection, but one reading alone doesn't confirm a bad part.

PP5V_S50.496––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail (S5/SUS, from the name), present whenever the board has standby power. The archive lists one known-good diode reading for it: 0.496 to ground, board unpowered. Check it in diode mode with power off, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode reading far from 0.496 usually points to a short or leak on that rail, but confirm with a voltage check before replacing anything.

PP18V5_S5_R0.536––
AI: what PP18V5_S5_R is and how to check it
  • What it is: PP18V5_S5_R is a standby-stage rail (the "S5" in the name), so it should be present whenever the board has standby power, before full power-on.
  • Known-good reading: diode mode to ground, board unpowered, 0.536. That's the only known-good value recorded for this rail; there's no known-good voltage here.
  • How to check: power off, measure diode to ground on the rail and compare with 0.536, then power up and measure the voltage on it.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher or open reading points to a missing connection or a part not feeding the rail. Confirm with a second measurement before replacing anything.
PPBUS_S5_HS_COMPUTING_ISNS0.43412.800–
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it

PPBUS_S5_HS_COMPUTING_ISNS is a current-sense line on the main PPBUS rail, in the S5 standby domain (from its name). Known-good readings are a diode drop of 0.434 to ground and 12.800 V with power applied; treat these as a community guide, not a guaranteed value.

  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered.
  • A diode reading far from 0.434 suggests a short or leaky part on that net; a voltage far from 12.800 V points to a fault on the PPBUS rail or its sensing path.
  • No known-good resistance reading exists for this net, so compare against a matching net or a known-good board.
PPBUS_S5_HS_OTHER_ISNS0.431––
AI: what PPBUS_S5_HS_OTHER_ISNS is and how to check it
  • What it is: From its name, PPBUS_S5_HS_OTHER_ISNS is a PPBUS main power rail segment in the S5 standby state, with "ISNS" indicating a current-sense connection. The board data doesn't list which parts sit on it.
  • Known-good reading: Diode mode to ground is 0.431 (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the DC voltage on the rail.
  • If it's far off: A much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open connection. Confirm with voltage under power before replacing anything.

S4 1

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.126––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail enabled at the S4 stage of the power sequence, which is a general reading of the name rather than something from this board's data. The archive lists one known-good reading for it: diode mode to ground 0.126, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is listed here. A diode reading far from 0.126 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

S3: memory 4

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V5_S30.062––
AI: what PP1V5_S3 is and how to check it

PP1V5_S3 is a 1.5 V rail; the S3 suffix, from its name, places it in the memory/startup stage. The archive lists one known-good diode reading of 0.062 to ground, with no condition noted. Check it unpowered in diode mode to ground, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.062 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part.

PP1V5_S3RS00.060––
AI: what PP1V5_S3RS0 is and how to check it

PP1V5_S3RS0 is a 1.5 V S3 (memory) rail, judged from its name; the archive lists a diode reading of 0.060 to ground. Check it unpowered in diode mode, red probe on ground and black on the rail, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far from 0.060 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S30.319––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that, from its S3 suffix, belongs to the memory stage of the power sequence. The archive lists one known-good reading: diode 0.319 in diode mode to ground, with no condition noted.

  • Check it with the board unpowered: diode mode, red probe on ground, black probe on the PP3V3_S3 test point or a component on that net.
  • Then power the board and measure the DC voltage on the same point; the archive has no known-good voltage for this rail, so compare against a known-good board or the rail's nominal 3.3 V.
  • A diode reading far below 0.319 usually points to a short or a leaky part on the rail; far above it suggests an open path or a missing connection. One reading alone doesn't confirm a bad part, so recheck and compare before replacing anything.
PP5V_S30.410––

S0: running 14

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.011––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail that is active in the S0 (running) state, judged from its name. The only known-good reading here is a diode value of 0.011 to ground; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.011 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part.

PP1V8_S0_CPU_VCCPLL_R0.126––
AI: what PP1V8_S0_CPU_VCCPLL_R is and how to check it

PP1V8_S0_CPU_VCCPLL_R is a 1.8 V rail feeding the CPU's PLL supply, judged from its name; the S0 suffix suggests it comes up in the running state. The archive lists one known-good diode reading of 0.126 to ground, with no condition noted and no known-good voltage reading here.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.126.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is recorded, so compare against a known-good board of the same model.
  • A diode reading far below 0.126 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. Confirm with voltage before replacing anything.
PP3V3_S00.321––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judging by its name; it is not a standby rail. The archive lists one known-good diode reading for it: 0.321 to ground, taken with the board unpowered. Check it in diode mode from the rail to ground with power off, then measure the voltage with the board powered and running; the archive has no known-good voltage for this rail, so compare against a known-good board or the same rail on a matching circuit. A diode reading far below 0.321 usually points to a short or a leaky part on the rail, while a much higher reading can mean an open trace or a missing connection. Confirm with a voltage measurement before replacing anything, since one reading alone doesn't prove a part is bad.

PP5V_S00.3885.000–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, based on its name. The archive lists a known-good diode reading of 0.388 to ground and 5.000 V with the board powered in S0; these are community readings and only a guide.

  • Check with the board unpowered: diode mode, red probe on ground, black on the PP5V_S0 test point or a component on that net.
  • Then power up into S0 and measure the voltage at the same point.

A diode reading far below 0.388 usually points to a short or a leaky part on the rail; a voltage well under 5.000 V in S0 points to the rail not coming up or being loaded down. No known-good resistance reading is listed for this rail.

PP5V_S0_PCH_V5REF0.365––
AI: what PP5V_S0_PCH_V5REF is and how to check it

PP5V_S0_PCH_V5REF is a 5 V rail that, from its name, runs in the S0 (running) state and feeds the PCH's 5 V reference. The archive lists one known-good diode reading of 0.365; there is no known-good voltage reading for this rail, so compare voltage against a matching rail or a known-good board. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.365 usually points to a short or a faulty component on that net, but one reading alone doesn't confirm a bad part.

PPBUS_S0_LCDBKLT_FUSED0.431––
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check it

PPBUS_S0_LCDBKLT_FUSED is the fused backlight power rail for the LCD, going by its name: PPBUS is the main bus supply, LCDBKLT is the display backlight, and the S0 suffix means it's live in the running state. The only known-good reading recorded is a diode value of 0.431 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on it. A diode reading far below 0.431 usually points to a short or leaky load on the rail, while a much higher or open reading suggests a broken path such as a blown fuse or open trace.

PPVCCSA_S0_CPU0.026––
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU is a CPU supply rail; the "S0" in the name indicates it is active in the running (S0) state, and "VCCSA" is generally the system-agent supply. The archive lists one known-good reading: diode 0.026 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.026 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part.

PPVCORE_S0_AXG0.0071.050–
AI: what PPVCORE_S0_AXG is and how to check it

PPVCORE_S0_AXG is the CPU core power rail; the "S0" in the name indicates it's active in the running state, and "VCORE" points to the processor core supply (from the name). The archive lists a known-good diode reading of 0.007 to ground and a voltage of 1.050, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode value far above 0.007 suggests an open or missing connection on the rail; a voltage well off 1.050 points to the core regulator or its enable not coming up. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.

PPVCORE_S0_AXG_R0.0071.050–
AI: what PPVCORE_S0_AXG_R is and how to check it

PPVCORE_S0_AXG_R is the CPU core rail; the S0 in its name indicates it is a running-state rail, and the AXG suffix is Apple's naming. From the readings archive, the known-good values are diode 0.007 and voltage 1.050 (no condition recorded), so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.007 usually points to a short or a leaky component on the rail; a voltage far from 1.050 points to a problem upstream in the rail's supply. No known-good resistance reading is available for this rail.

PPVCORE_S0_CPU0.0061.250–
AI: what PPVCORE_S0_CPU is and how to check it

PPVCORE_S0_CPU is the CPU core power rail; the S0 in its name indicates it is active in the running state. From the readings archive, the known-good guide values are a diode reading of 0.006 to ground and 1.250 V with power applied. Check it by measuring diode mode from the rail to ground with the board unpowered, then measure the voltage with the board powered. A voltage far from 1.250 V points to a problem in that rail's supply or loading, but a single reading isn't proof a part is bad; no known-good resistance value is recorded for this rail.

PPVCORE_S0_CPU_PH10.0061.250–
AI: what PPVCORE_S0_CPU_PH1 is and how to check it

PPVCORE_S0_CPU_PH1 is the CPU core power rail (VCORE) in the running (S0) state, judged from its name; the PH1 suffix suggests a switching phase node. The archive lists diode 0.006 and voltage 1.250 for it, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.006 usually points to a short or a leaky component on that rail, while a voltage well off 1.250 points to the core regulator or its feedback not coming up. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PPVCORE_S0_CPU_PH1_L0.0061.250–
AI: what PPVCORE_S0_CPU_PH1_L is and how to check it

PPVCORE_S0_CPU_PH1_L is the CPU core power rail (VCORE) in the S0 running state, judging by its name; the PH1 suffix usually marks a switching-node phase of the CPU buck converter (general interpretation, not from board data).

  • Known-good readings here: diode 0.006 to ground and 1.250 V with power applied. These are community readings and only a guide.
  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running.
  • A diode reading far above 0.006 suggests an open or high-resistance path rather than a short; a voltage far from 1.250 V under load points to the CPU buck converter or its feedback, not the rail itself.
  • No known-good resistance reading is recorded for this rail.
PPVCORE_S0_CPU_PH20.0061.250–
AI: what PPVCORE_S0_CPU_PH2 is and how to check it

PPVCORE_S0_CPU_PH2 is a CPU core power rail; the "S0" in its name indicates it belongs to the running (S0) state, and "PH2" suggests a phase of the CPU buck converter (from the name, not confirmed by board data).

  • Known-good readings from the archive: diode 0.006 to ground, voltage 1.250. These are community values and a guide only.
  • Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board in S0.
  • No known-good resistance reading here; compare against a matching phase or a known-good board of the same model.
  • A diode reading far from 0.006 usually points to a short or a faulty component on the rail; a missing or wrong voltage points to the converter or its enable. Neither is confirmed until traced.
PPVCORE_S0_CPU_PH2_L0.0061.250–
AI: what PPVCORE_S0_CPU_PH2_L is and how to check it

PPVCORE_S0_CPU_PH2_L is a CPU core power rail; the S0 in the name indicates the running state. The archived readings give a diode value of 0.006 to ground and 1.250 V with power applied, as a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board running. A voltage far from 1.250 V points to the core supply not coming up or being loaded down, but no known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning anything.

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD–3.300–
BKL_EN0.535––
CHGR_ACIN0.5423.900–
CHGR_AGATE0.645––
CHGR_AGATE_DIVOL––
CHGR_AMON0.719––
CHGR_BGATE0.67112.470–
CHGR_BMON0.725––
CHGR_BOOT0.594––
CHGR_CELL0.7173.400–
CHGR_CSI_N0.654––
CHGR_CSI_P0.633––
CHGR_CSO_N0.49812.460–
CHGR_CSO_P0.45512.490–
CHGR_CSO_R_N0.431––
CHGR_CSO_R_P0.431––
CHGR_DCIN0.62016.430–
CHGR_DCIN_D_R0.607––
CHGR_ICOMP0.7232.100–
CHGR_LGATE0.4662.500–
CHGR_PHASE0.461––
CHGR_RST_L0.5173.400–
CHGR_SGATE0.658––
CHGR_UGATE0.916––
CHGR_VCOMP0.7241.800–
CHGR_VFRQ0.539––
CHGR_VNEG0.541––
CPUIMVP_ISNS1_N0.0061.250–
CPUIMVP_ISNS1_P0.0061.250–
CPUIMVP_ISNS1G_N0.0071.050–
CPUIMVP_ISNS1G_P0.0071.050–
CPUIMVP_ISNS2_N0.0061.250–
CPUIMVP_ISNS2_P0.0061.250–
CPUIMVP_LGATE1G0.466––
CPUIMVP_PHASE10.006––
CPUIMVP_PHASE1G0.007––
CPUIMVP_UGATE10.674––
CPUIMVP_UGATE1G_R0.676––
CPUIMVP_UGATE2_R0.676––
CPUIMVP_VR_ON0.4513.300–
CPUIMVP_VSWG0.0071.050–
FAN_RT_PWM0.960––
FAN_RT_TACHOL––
ISNS_HS_COMPUTING_N0.434––
ISNS_HS_COMPUTING_P0.434––
ISNS_HS_OTHER_N0.431––
ISNS_HS_OTHER_P0.431––
P3V3SUS_SS1.796––
P3V42G3H_SW0.338––
P5V_S0_CPUIMVP_VDD0.3915.000–
P5VS3_LL0.410––
PP1V05_S00.011––
PP1V5_S30.062––
PP1V5_S3RS00.060––
PP1V8_S0_CPU_VCCPLL_R0.126––
PP3V3_S00.321––
PP3V3_S30.319––
PP3V3_S40.126––
PP3V3_S50.125––
PP3V3_SUS0.400––
PP3V42_G3H0.3383.400–
PP5V_S00.3885.000–
PP5V_S0_PCH_V5REF0.365––
PP5V_S30.410––
PP5V_S50.496––
PP5V1_CHGR_VDD0.4625.000–
PP5V1_CHGR_VDDP0.4645.000–
PP15V_T290.530––
PP18V5_DCIN_FUSE0.645––
PP18V5_S5_R0.536––
PPBUS_G3H0.434––
PPBUS_S0_LCDBKLT_FUSED0.431––
PPBUS_S5_HS_COMPUTING_ISNS0.43412.800–
PPBUS_S5_HS_OTHER_ISNS0.431––
PPBUS_SW_BKL0.406––
PPBUS_SW_LCDBKLT_PWR0.406––
PPBUS_SW_LCDBKLT_PWR_SW0.406––
PPDCIN_G3H0.64516.730–
PPDCIN_G3H_CHGR0.604––
PPDCIN_G3H_INRUSH_FETOL––
PPVBAT_G3H_CHGR_R0.431––
PPVBAT_G3H_CHGR_REG0.431––
PPVBAT_G3H_CONNOL Con BateriaOL11.100 Con Bateria11.100–
PPVCCSA_S0_CPU0.026––
PPVCORE_S0_AXG0.0071.050–
PPVCORE_S0_AXG_R0.0071.050–
PPVCORE_S0_CPU0.0061.250–
PPVCORE_S0_CPU_PH10.0061.250–
PPVCORE_S0_CPU_PH1_L0.0061.250–
PPVCORE_S0_CPU_PH20.0061.250–
PPVCORE_S0_CPU_PH2_L0.0061.250–
PPVOUT_SW_LCDBKLT0.558––
PPVOUT_SW_LCDBKLT_FB0.558––
SMBUS_SMC_BSA_SCL0.4763.400 Con Bateria3.400–
SMBUS_SMC_BSA_SDA0.4763.400 Con Bateria3.400–
SMC_BC_ACOK0.5083.400–
SMC_RESET_L–3.400–
SYS_DETECT_L0.679 Con Bateria1.6280.032 Con Bateria0.032–
WS_CONTROL_KBD0,465––
WS_KBD_ONOFF_L1,178––
WS_KBD10,686––
WS_KBD20,687––
WS_KBD30,686––
WS_KBD40,687––
WS_KBD50,685––
WS_KBD60,687––
WS_KBD70,687––
WS_KBD80,684––
WS_KBD90,688––
WS_KBD100,685––
WS_KBD110,687––
WS_KBD120,683––
WS_KBD130,688––
WS_KBD140,684––
WS_KBD15_CAP0,991––
WS_KBD16_NUMOL––
WS_KBD170,688––
WS_KBD180,686––
WS_KBD190,689––
WS_KBD200,678––
WS_KBD210,685––
WS_KBD220,682––
WS_KBD230,690––
WS_LEFT_OPTION_KBD0,429––
WS_LEFT_SHIFT_KBD0,411––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-2936?

OpenBoardData's known-good values for PPBUS_G3H on the 820-2936: diode 0.434. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-2936?

OpenBoardData's known-good values for PP3V42_G3H on the 820-2936: diode 0.338, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-2936?

OpenBoardData's known-good values for PP5V_S5 on the 820-2936: diode 0.496. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-2936 board?

Open your own 820-2936 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License