Apple laptop board · OpenBoardData

820-3435 known-good readings

Known-good readings for the Apple laptop board 820-3435: 66 nets, including 25 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 25 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3435.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 25 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 9

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.3143.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on the 820-3435, a startup-stage supply that should be present whenever power is connected (from its name: G3H = always on).

  • Known-good readings (community archive, guide only): diode 0.314, voltage 3.400.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A voltage far below 3.4 V points to a fault on the rail or its source; a diode reading far from 0.314 suggests a short or open on the net.
  • No known-good resistance reading is available for this rail.
PPBUS_G3H0.1488.540–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the "G3H" suffix indicates it is always-on (from the name). Known-good readings for this board: diode 0.148 and voltage 8.540. Check it with the board unpowered in diode mode from PPBUS_G3H to ground, then power up and measure the voltage. A diode reading far from 0.148 suggests a short or leaky component on the rail; a voltage far from 8.540 points to a charging or power-supply fault. No known-good resistance reading here; compare against a matching rail or a known-good board.

PPBUS_G3H_R0.1558.540–
AI: what PPBUS_G3H_R is and how to check it
  • What it is: PPBUS_G3H_R is the main "always on" bus rail; the G3H part of the name indicates it is present whenever power is connected, before the board fully starts.
  • Known-good readings (guide, from community data): diode 0.155 to ground, and 8.540 V with power applied.
  • How to check: with the board unpowered, measure diode mode from PPBUS_G3H_R to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or heavy load on the rail, but one reading alone doesn't confirm a bad part. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board.
PPDCIN_G3H0.70914.400–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on G3H input rail on the 820-3435; the "G3H" in the name indicates it is present whenever the adapter is connected, before the board is switched on. The archive lists a known-good diode reading of 0.709 to ground and a voltage of 14.400, both as community guides rather than confirmed values.

To check it, power the board off and measure diode mode from PPDCIN_G3H to ground, then apply power and measure the voltage on the rail. A diode reading far below 0.709 suggests a short or leaky component pulling the rail down, while a voltage well under 14.400 with a good adapter points to a break or high resistance in the input path. No known-good resistance reading is available for this rail, so compare against a matching net or a known-good board if needed.

PPDCIN_G3H_CHGR0.58314.360–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H part of the name indicates it is always-on, present whenever the charger is connected. The archive lists a known-good diode reading of 0.583 and a voltage of 14.360, with no condition noted, so treat these as a guide only. With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail. A diode reading far below 0.583 usually points to a short or a leaky part on the rail, while a voltage well under 14.360 with a good charger suggests the input path is not passing power. No known-good resistance reading is available for this rail.

PPDCIN_G3H_INRUSH0.58314.250–
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is the main DC input rail on the 820-3435; the G3H part of the name indicates it's an always-on rail, present whenever the adapter is connected. The archived readings for it are diode 0.583 and voltage 14.250, which are community figures and a guide only, not a guaranteed value.

To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage on the rail. No known-good resistance reading exists here, so compare against a matching net or a known-good board if you need one.

A diode reading far below 0.583 usually suggests a short or a leaky part on the rail; a voltage well under 14.250 with the adapter connected points to a problem upstream in the input path. These are likely causes, not confirmed ones, so trace the input side before replacing anything.

PPDCIN_G3H_ISOL–14.820–
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is the isolated DC input rail; the G3H part of the name indicates it is always on, from the name. The archive lists one known-good voltage of 14.820 V, with no condition recorded, and no known-good diode or resistance reading for this rail. With the board unpowered, check diode mode from the rail to ground, then apply power and measure the voltage. A voltage far below 14.820 V usually points to a problem upstream in the input path, such as the adapter, input fuse or isolation components, rather than to a fault on the rail itself.

PPVBAT_G3H_CHGR_REG–8.600–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is the charger-side battery rail; "G3H" in the name marks it as an always-on rail, and "CHGR" points to the charger circuit. The only known-good value here is 8.600 V, with no condition recorded, and there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 8.600 V suggests the charger side or its supply is not coming up, but that is a likely cause, not a confirmed one; compare against a matching rail on a known-good board before replacing anything.

PPVIN_G3H_P3V42G3H0.39914.510–
AI: what PPVIN_G3H_P3V42G3H is and how to check it

PPVIN_G3H_P3V42G3H — reference note

  • This is the always-on input rail feeding the P3V42G3H supply, from the name: "PPVIN" is the main adapter input and "G3H" means always on. It should be present whenever the adapter is connected.
  • Known-good readings here: diode 0.399 to ground, and 14.510 V with power applied. These come from community contributions and are a guide only.
  • To check it: power off and unplug the adapter, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.399 suggests a short or leaky load on the rail; a voltage far from 14.510 V with a good adapter points to a problem upstream in the input path. No known-good resistance reading here, so compare against a matching net or a known-good board.

S5 and SUS: standby 4

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S5–3.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the S5/SUS part of the name marks it as a standby rail, which is from the name rather than from a schematic. The archive lists one known-good value, 3.300 V, with no condition attached, and no known-good diode or resistance reading for this net. With the board unpowered, check diode mode from PP3V3_S5 to ground and compare against a matching standby rail or a known-good board. Then power up and confirm about 3.300 V. A voltage far below that suggests the standby supply isn't coming up or the rail is loaded down, but a single reading doesn't confirm a bad part, so check the supply side before replacing anything.

PP3V3_S5_REG_R–3.300–
AI: what PP3V3_S5_REG_R is and how to check it
  • What it is: From its name, PP3V3_S5_REG_R is a 3.3 V regulated rail in the S5/SUS standby stage, so it should be present before the board fully powers on.
  • Known-good reading: 3.300 V is listed for this rail; no diode or resistance value is recorded here, so there is no known-good reading of that kind.
  • How to check: With the board unpowered, measure diode mode from the rail to ground, then apply power and measure the voltage at the rail.
  • If it's off: A voltage far from 3.300 V usually points to the rail's regulator or its enable/feedback path, or to a heavy load pulling it down. Compare the diode reading against a matching standby rail or a known-good board before suspecting a part.
PPBUS_S5_HS_COMPUTING_ISNS–8.540–
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check it
  • What it is: From the name, PPBUS_S5_HS_COMPUTING_ISNS is a PPBUS rail segment at the S5 standby stage, with "ISNS" indicating a current-sense line. The board data doesn't list which parts sit on it.
  • Known-good reading: 8.540 V, with no condition recorded. There is no known-good diode or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground; then apply power and measure the voltage, comparing it with 8.540 V.
  • If it's far off: A voltage well away from 8.540 V usually points to a problem in the PPBUS supply or a load pulling the rail down, but that's a likely cause, not a confirmed one. A diode reading far from a matching net on a known-good board is the better clue, since no known-good diode value exists here.
PPBUS_S5_HS_OTHER_ISNS–8.600–
AI: what PPBUS_S5_HS_OTHER_ISNS is and how to check it

PPBUS_S5_HS_OTHER_ISNS is a standby-stage power rail; the S5/SUS part of the name indicates it is present in standby, and PPBUS is the main bus fed by the charger/DC-in section (general naming, not from this board's data). The only known-good reading here is 8.600 V, with no condition recorded. No known-good diode or resistance reading is available for this rail. With the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage. A voltage far from 8.600 V points to a problem in the bus supply or a load pulling it down, but one reading alone doesn't confirm a bad part.

S4 1

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP5V_S4RS30.4305.000–
AI: what PP5V_S4RS3 is and how to check it

PP5V_S4RS3 is a 5 V rail in the S4 startup stage, as the name indicates. Known-good readings from the archive: diode 0.430 to ground and 5.000 V when present. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode reading far from 0.430 suggests a short or leak on the rail; no known-good resistance reading is recorded here.

S3: memory 2

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S3–1.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V supply rail; the S3 suffix indicates the memory stage of the power sequence (from the name). The archive lists a known-good voltage of 1.200 V; there is no known-good diode or resistance reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 1.200 V, or a diode reading very different from a matching rail, usually points to a short, a missing enable, or a faulty regulator, but that is a likely cause, not a confirmed one.

PPDDR_S3_REG_R–1.200–
AI: what PPDDR_S3_REG_R is and how to check it

PPDDR_S3_REG_R is a memory-stage (S3) rail, judged from its name; the data gives no part list for it. Its only known-good reading here is 1.200 V, with no condition recorded, and there is no known-good diode or resistance value. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. A voltage far from 1.200 V points to the rail not coming up or being loaded down, but that is a likely cause, not a confirmed one.

S0: running 9

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S0_REG_R–1.058–
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R — reference note

  • From its name, this is a 1.05 V rail (PP1V05) that is switched on in the S0 running state and is a regulated supply (REG). The "_R" suffix usually marks a remote or secondary sense point of that rail; that part is general convention, not from this board's data.
  • The only archived reading is 1.058 V, with no stated condition. No known-good diode or resistance reading exists here for this net.
  • To check it: power off and check diode mode to ground on the rail, then power up and measure the voltage. Compare the diode reading with a matching rail on the other side of a pair, or with a known-good board, since no reference value is recorded.
  • A voltage far from about 1.05 V, or a diode reading very different from a comparable rail, usually points to a short, an open feed, or the regulator not being enabled — a likely cause, not a confirmed one.
PP3V3_S00.690––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, inferred from the rail name. The archive lists a known-good diode reading of 0.690 to ground for this rail; no known-good voltage reading is recorded here.

  • Check it unpowered: diode mode, black probe on ground, red on PP3V3_S0, and compare with 0.690.
  • Then power the board and measure the voltage on the rail; the archive has no known-good voltage, so compare against a known-good board or the rail's nominal 3.3 V.
  • A diode reading far below 0.690 usually points to a short or a leaky part on the rail; a reading far above it can mean an open connection. One reading alone doesn't confirm a bad part.
PP3V3_S0SW_SSD0.530––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is a 3.3 V rail switched on in the S0 (running) state, feeding the SSD; the S0 and SSD parts come from the name. The archive lists one known-good diode reading of 0.530 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.530 suggests a short or leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S0SW_SSD_FLT0.553––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it
  • What it is: From the name, PP3V3_S0SW_SSD_FLT is a 3.3 V rail that is switched (SW) and feeds the SSD, active in the S0 (running) state. "FLT" suggests a filtered or fault-related variant; the exact function isn't in the data.
  • Known-good reading: Diode mode to ground is 0.553. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground, then power up and measure the voltage. Compare the diode reading with 0.553.
  • If it's far off: A much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open path. Treat 0.553 as a guide only, since readings vary with board state.
PP5V_S0–5.000–
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, as the name indicates. The archive lists a known-good voltage of 5.000 V for this rail; there is no known-good diode or resistance reading here.

  • Check it unpowered in diode mode from PP5V_S0 to ground, then power the board and measure the voltage.
  • A voltage far from 5.000 V in S0 points to the rail not coming up or being loaded down; a low diode reading to ground suggests a short on the rail.
  • Without a known-good diode value, compare against a matching 5 V rail or a known-good board of the same model.
PPVCC_S0_CPU–1.800–
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the "S0" in the name indicates it is up in the running state. The archive lists one known-good voltage of 1.800 V, with no condition noted and no diode or resistance reading for this net. Check it unpowered in diode mode to ground first, then power the board and measure the voltage at the rail. A voltage far from 1.800 V, or a short to ground in diode mode, usually points to a fault on the rail or its supply rather than the CPU itself; with no known-good diode value here, compare against a matching rail on a known-good board.

PPVCC_S0_CPU_PH1–1.800–
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 is a CPU power rail; the S0 in its name indicates it belongs to the running (S0) state, and PH1 suggests one phase of a multi-phase CPU supply. The archive lists one known-good voltage of 1.800 V, with no condition noted and no diode or resistance reading, so there is no known-good diode value here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 1.800 V points to the CPU supply not coming up or being loaded down, but that is a likely area, not a confirmed fault; compare diode readings against a matching rail or a known-good board before replacing anything.

PPVCC_S0_CPU_PH2–1.800–
AI: what PPVCC_S0_CPU_PH2 is and how to check it
  • What it is: From the name, PPVCC_S0_CPU_PH2 is a CPU power rail (VCC) active in the S0 running state, phase 2 of a multiphase CPU supply. It's a high-current rail, so treat it with care.
  • Known-good reading: The archive lists 1.800 V for this rail. No diode or resistance value is recorded here, so there's no known-good reading of that kind to compare against.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with a matching phase or a known-good board. Then apply power and measure the voltage, expecting about 1.800 V once the board is in S0.
  • If it's far off: A very low diode reading suggests a short on the rail; no voltage at all points to the supply not being enabled or a failed phase. Confirm with a second measurement before replacing anything.
PPVMEMIO_S0_CPU–1.200–
AI: what PPVMEMIO_S0_CPU is and how to check it

PPVMEMIO_S0_CPU is a memory I/O rail for the CPU; the S0 in the name indicates it belongs to the running (S0) power state, and this is inferred from the name rather than from board data. The only known-good reading recorded here is 1.200 V, with no condition noted; there is no known-good diode or resistance value for this rail.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A voltage far from 1.200 V, or a diode reading very different from a matching rail on the other side of a pair or a known-good board, points to a fault on that rail or its load rather than confirming a bad part.
  • No known-good diode or resistance reading is available here, so compare against a known-good board.

Every net with a reading

NetDiodeVoltageResistance
CHGR_CSI_R_N0.58314.200–
CHGR_CSI_R_P0.58314.200–
CHGR_PHASE–8.670–
CPUVR_PHASE1–1.800–
CPUVR_PHASE2–1.800–
DCIN_ISOL_GATE0.7716.700–
DCIN_ISOL_GATE_R2.8166.700–
I2C_ALS_1V8_SCL0.601––
JP600_PIN_320.601––
P1V05S0_LL–1.072–
P3V3_S5_REG_L–3.300–
P3V3SSD_VMON0.484––
P3V42G3H_BOOST–7.160–
P3V42G3H_FB–1.300–
P3V42G3H_SHDN_L–14.510–
P3V42G3H_SW0.3143.400–
P5V_S4RS3_REG_L–5.000–
PDDR_S3_REG_L–1.200–
PP1V2_S3–1.200–
PP1V05_S0_REG_R–1.058–
PP3V3_S00.690––
PP3V3_S0SW_SSD0.530––
PP3V3_S0SW_SSD_FLT0.553––
PP3V3_S5–3.300–
PP3V3_S5_REG_R–3.300–
PP3V42_G3H0.3143.400–
PP5V_S0–5.000–
PP5V_S4RS30.4305.000–
PP5V1_CHGR_VDD–5.000–
PP5V1_CHGR_VDDP–5.000–
PP18V5_DCIN_ISOL_R–14.770–
PPBUS_G3H0.1488.540–
PPBUS_G3H_R0.1558.540–
PPBUS_S5_HS_COMPUTING_ISNS–8.540–
PPBUS_S5_HS_OTHER_ISNS–8.600–
PPDCIN_G3H0.70914.400–
PPDCIN_G3H_CHGR0.58314.360–
PPDCIN_G3H_INRUSH0.58314.250–
PPDCIN_G3H_ISOL–14.820–
PPDDR_S3_REG_R–1.200–
PPVBAT_G3H_CHGR_REG–8.600–
PPVCC_S0_CPU–1.800–
PPVCC_S0_CPU_PH1–1.800–
PPVCC_S0_CPU_PH2–1.800–
PPVIN_G3H_P3V42G3H0.39914.510–
PPVMEMIO_S0_CPU–1.200–
S0PGD_C–0.130–
SMC_FAN_0_TACH0.736––
SMC_MANUAL_RST_L–2.700–
SMC_OOB1_D2R_CONN_LOL––
SMC_OOB1_D2R_L0.670––
SMC_OOB1_R2D_CONN_LOL––
SMC_OOB1_R2D_L0.645––
SSD_CLKREQ_CONN_L0.435––
SSD_CLKREQ_L0.460––
SSD_PWR_EN0.360––
SSD_RESET_CONN_L0.433––
SSD_RESET_L0.453––
UNCONNECTED_123OL14.270–
UNCONNECTED_124OL14.270–
UNCONNECTED_125OL14.270–
UNCONNECTED_126OL14.270–
VMON_3V3_DIV–0.720–
VMON_5V_DIV–0.670–
VMON_Q2_BASE–0.635–
VMON_Q3_BASE–0.656–

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-3435?

OpenBoardData's known-good values for PPBUS_G3H on the 820-3435: diode 0.148, voltage 8.540. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-3435?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3435: diode 0.314, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-3435?

OpenBoardData's known-good values for PP3V3_S5 on the 820-3435: voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3435 board?

Open your own 820-3435 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License