Apple laptop board · OpenBoardData

820-01521 known-good readings

Known-good readings for the Apple laptop board 820-01521: 1,310 nets, including 79 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 77 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01521.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 79 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 33

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.3171.800–
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V always-on rail; the G3S suffix comes from its name and places it in the always-on startup group. Known-good readings for this board: diode 0.317 and voltage 1.800 (community archive, guide only). Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.317 suggests a short or a damaged load on the rail; a voltage well below 1.800 points to the rail not coming up or being pulled down. No known-good resistance reading is listed for this rail.

PP1V8_G3S_THMSNS_R0.333––
AI: what PP1V8_G3S_THMSNS_R is and how to check it
  • What it is: A 1.8 V rail, from the name: the "1V8" is the voltage, "G3S" is the always-on (G3H-family) startup stage, and "THMSNS" suggests a thermal-sense related supply (general reading of the name, not from board data).
  • Known-good reading: diode 0.333 to ground, from the community archive; treat it as a guide, since readings vary with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground, then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open connection. Confirm with a second measurement before replacing anything.
PP3V_G3H0.4713.000–
AI: what PP3V_G3H is and how to check it

PP3V_G3H is the always-on 3.3 V rail in the G3H startup stage, judged from its name (G3H = always on). Known-good readings here: diode 0.471 to ground and 3.000 V with power applied; these are community values and a guide only.

  • With the board unpowered, measure diode mode from PP3V_G3H to ground and compare with 0.471.
  • With power applied, measure the voltage and compare with 3.000 V.
  • A far-off diode reading usually points to a short or a damaged part on the rail; a missing or low voltage points to the rail not being enabled or its source failing. No known-good resistance reading exists for this rail.
PP3V3_G3H0.3823.300150.000
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H — 820-01521 reference note

  • What it is: a 3.3 V always-on rail. The "G3H" suffix, from the name, marks it as part of the always-on (G3) power domain, so it should be present whenever the board has input power, before the main rails come up.
  • Known-good readings (community, guide only): diode 0.382, voltage 3.300, resistance 150.000. No condition is recorded with these values.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage. The CD3215 sequence also lists it at L6900 pin 2 (3V3) and its enable PM_EN_P3V3_G3H at U6903 pin 10.
  • If far from known-good: a low or shorted diode reading points to a short on the rail; a correct diode reading with no voltage points upstream, to the rail's regulator or its enable. No known-good reading of other kinds is recorded here, so compare against a matching rail or a known-good board.
PP3V3_G3H_DEBUGLED_ROL––
AI: what PP3V3_G3H_DEBUGLED_R is and how to check it
  • What it is: A 3.3 V always-on rail in the G3H startup stage, judged from the name (G3H = always on; DEBUGLED suggests a debug LED feed). It is not the main PP3V3_G3H rail listed in the sequence checks.
  • Known-good readings: The archive lists diode mode to ground as OL on this net. No known-good voltage reading here.
  • How to check: Power off, then diode mode from the net to ground and compare with the OL figure. Then power up and measure the voltage; expect about 3.3 V from the name, but that is general, not a recorded value.
  • If far off: A short or very low diode reading points to a fault on that net or its load. A missing voltage with a normal diode reading points upstream, toward the always-on 3V3 source. Treat this as a likely cause, not a confirmed one.
PP3V3_G3H_DEBUGLED_RROL––
AI: what PP3V3_G3H_DEBUGLED_RR is and how to check it
  • What it is: PP3V3_G3H_DEBUGLED_RR is a 3.3 V always-on rail, judged from its name (PP3V3 = 3.3 V, G3H = always-on, DEBUGLED = debug LED). It is not the same net as PP3V3_G3H, which the notes list at L6900 pin 2.
  • Known-good readings: the only archived value is diode OL (open, no conduction to ground). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far from known-good: a short or low diode reading suggests a fault on the rail; a wrong voltage with a normal diode reading points upstream. This is general guidance, not confirmed for this board.
PP3V3_G3H_IPD_F0.3823.300–
AI: what PP3V3_G3H_IPD_F is and how to check it
  • What it is: PP3V3_G3H_IPD_F is a 3.3 V rail in the always-on G3H startup stage, judging by its name (G3H = always on). "IPD_F" likely marks a filtered branch, but that's general naming, not from the board data.
  • Known-good readings (community guide): diode 0.382 to ground, voltage 3.300 V. No known-good resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a low diode reading or missing 3.3 V usually points to a short or a rail that isn't being enabled, but one reading doesn't confirm a bad part. Check the upstream enable and source before replacing anything.
PP3V3_G3H_PMU_VDDMAIN0.382–389.600
AI: what PP3V3_G3H_PMU_VDDMAIN is and how to check it
  • What it is: From the name, PP3V3_G3H_PMU_VDDMAIN is a 3.3 V always-on rail feeding the PMU's main supply. G3H means "always on", so it should be present whenever the board has power.
  • Known-good readings (community guide): diode 0.382 and resistance 389.6 Ω. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground, then resistance. Then apply power and measure the voltage on the rail.
  • If far off: a diode or resistance far below known-good usually points to a short or a leaky part on the rail; a missing or low voltage with normal diode readings points upstream, toward the always-on supply that generates it. Confirm with a second measurement before replacing anything.
PP3V3_G3H_RTC0.4533.300–
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC — from the name, a 3.3 V always-on (G3H) rail feeding the RTC section. Known-good readings in the archive: diode 0.453 to ground, and 3.300 V with power applied. No known-good resistance reading here.

  • Check it unpowered in diode mode from the rail to ground; a far lower reading usually points to a short or a leaky part on the rail, a far higher one to an open feed.
  • Then power the board and measure the voltage; a missing or low 3.3 V points upstream to its source or enable, not to the RTC load.
  • These are community readings and vary with board state, so treat them as a guide and compare against a matching rail on a known-good board where possible.
PP3V3_G3H_RTC_R0.4533.3003.864R
AI: what PP3V3_G3H_RTC_R is and how to check it
  • What it is: From the name, a 3.3 V always-on rail (G3H) feeding the RTC circuit. It is an always-on rail, so it should be present whenever the board has power, not only after the main power-on sequence.
  • Known-good readings (community guide): diode 0.453, voltage 3.300, resistance 3.864R. These vary with board state.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the DC voltage.
  • If far off: a much lower diode or resistance reading usually points to a short or a leaky part on the rail; a missing 3.3 V with a normal diode reading points upstream, toward the rail's source. No known-good waveform or current draw is listed here.
PP3V3_G3S0.3363.300140.000
AI: what PP3V3_G3S is and how to check it
  • PP3V3_G3S is a 3.3 V always-on rail; the "G3S" part of the name indicates it is present in the always-on state (from the name, not from a schematic).
  • Known-good readings here: diode 0.336, voltage 3.300 V, resistance 140.000 (community values, a guide only; no condition recorded).
  • Check it unpowered in diode mode to ground first, then measure the voltage with the board powered.
  • A diode or resistance far below known-good usually points to a short or a leaky part on the rail; a voltage well off 3.3 V points to the rail not coming up or being loaded down. No known-good waveform or current draw is listed here.
PP3V3_G3S_G3H_RIO0.40––
AI: what PP3V3_G3S_G3H_RIO is and how to check it

PP3V3_G3S_G3H_RIO — reference note

  • From its name this is a 3.3 V rail in the G3H group, meaning it should be present whenever the board has power (always-on), not just after the main supply comes up. "RIO" is part of the net name; the data doesn't explain what it feeds.
  • Known-good reading here: diode mode 0.40 to ground, board unpowered. No known-good voltage reading is recorded for this rail.
  • To check it: power off and measure diode mode from the rail to ground, then power the board and measure the voltage at the same point. Compare the diode reading with 0.40.
  • A diode reading far below 0.40 suggests a short or a leaky load on the rail; far above it suggests an open path. A missing or wrong voltage with a normal diode reading points more toward the supply side of the rail than the load.
PP3V3_G3S_IPD_F0.3363.300–
AI: what PP3V3_G3S_IPD_F is and how to check it

PP3V3_G3S_IPD_F — reference note

  • What it is: a 3.3 V rail in the G3S (always-on) startup stage, judging from the name; the "IPD_F" suffix is not explained by the name alone.
  • Known-good readings (community archive, guide only): diode 0.336 and voltage 3.300. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a low diode reading or a collapsed voltage points to a short or heavy load on the rail, but one reading doesn't confirm a bad part — compare against a known-good board or a matching rail before replacing anything.
PP3V3_G3S_WLANBT0.336–140.000
AI: what PP3V3_G3S_WLANBT is and how to check it

PP3V3_G3S_WLANBT — 820-01521 reference note

  • What it is: a 3.3 V rail feeding the WLAN/Bluetooth section. The "G3S" in the name indicates it is an always-on (G3H-stage) supply, so it should be present whenever the board has power, not only after the main power sequence.
  • Known-good readings (community archive, guide only): diode 0.336 to ground, resistance 140.000. No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.336; then apply power and measure the rail voltage, expecting about 3.3 V.
  • If readings are far off: a much lower diode or resistance reading suggests a short or leaky load on the rail; an open or high reading suggests a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_G3SSW_SNS0.5443.300–
AI: what PP3V3_G3SSW_SNS is and how to check it

PP3V3_G3SSW_SNS is a 3.3 V always-on rail; the G3H part of the name indicates it belongs to the always-on startup stage (from the name).

  • Known-good readings from the archive: diode 0.544 and voltage 3.300. These are community values and vary with board state, so treat them as a guide.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and confirm about 3.300 V.
  • A voltage well below 3.300 V with power applied points to the rail not coming up or being loaded down; a diode reading far from 0.544 suggests a short or a faulty component on the rail. No known-good resistance reading is listed here.
  • Confirm with a second measurement before replacing anything; a likely cause is not a confirmed one.
PP5V_G3S0.4085.0000.420R
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V rail in the G3H (always-on) startup group, judging from the name. The archive lists known-good readings of diode 0.408, voltage 5.000 and resistance 0.420R; these are community values and a guide only.

  • With the board unpowered, measure diode mode from PP5V_G3S to ground and compare with 0.408.
  • Then apply power and check for 5.000 V, and confirm the rail is present at its expected startup point.
  • A diode reading far below known-good often suggests a short or a failing load on the rail; a missing 5 V with a normal diode reading points more to the supply or enable side. No known-good value of another kind is listed here.
PP5V_G3S_IPD_F0.4085.000–
AI: what PP5V_G3S_IPD_F is and how to check it
  • What it is: PP5V_G3S_IPD_F is a 5 V rail. From the name, G3S is a switchable (S-state) rail, not an always-on one, and IPD likely refers to an input power detection function. This is inferred from the name only; the parts on this net aren't listed in the archive.
  • Known-good readings (community guide): diode 0.408 to ground, and 5.000 V with power applied. No condition is recorded for either.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.408. Then power up and measure the voltage, expecting about 5.000 V.
  • If far off: a low diode reading suggests a short or leaky load on the rail; a correct diode reading with missing voltage points upstream, to the rail's enable or source. No known-good resistance reading exists here, so compare against a matching net or a known-good board before replacing anything.
PP5V_G3S_P1V1REG0.428––
AI: what PP5V_G3S_P1V1REG is and how to check it

PP5V_G3S_P1V1REG — reference note

  • From its name, this is a 5 V rail in the G3S (always-on) group, with a 1V1 regulator association; the name alone doesn't confirm which parts sit on it.
  • Known-good reading: diode 0.428 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check with power off: meter in diode mode, black probe on ground, red on the rail, and compare with 0.428. Then power up and measure the DC voltage on the rail.
  • A diode reading far below 0.428 usually points to a short or a leaky load on the rail; far above suggests an open path. One reading isn't proof, so confirm with a second point on the same rail before replacing anything.
PP5V_G3S_VCCIOPVCC0.411––
AI: what PP5V_G3S_VCCIOPVCC is and how to check it
  • What it is: PP5V_G3S_VCCIOPVCC is a 5V rail for the G3S (always-on) domain, from its name; the VCCIOPVCC part suggests it feeds an I/O or PVCC supply, but the exact loads aren't documented here.
  • Known-good reading: diode 0.411 to ground (community value, a guide only). No known-good voltage reading is listed for this rail.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP5V_G3S_VCCIOVCC0.411––
AI: what PP5V_G3S_VCCIOVCC is and how to check it

PP5V_G3S_VCCIOVCC — reference note

  • From the name, this is a 5 V rail in the G3S group (the G3H/G3S naming on this board marks the always-on startup region), feeding VCCIO/VCC supply. The name is the only description available here; which parts sit on the net isn't recorded.
  • Known-good reading: diode 0.411 in diode mode to ground, board unpowered. No known-good voltage reading is recorded for this rail.
  • To check it: power off and confirm no adapter or battery, then measure diode mode from the rail to ground and compare with 0.411. Then apply power and measure the DC voltage at the rail.
  • A diode reading far below 0.411 suggests a short or a leaky load on the rail; a much higher or open reading suggests a broken path or missing connection. One reading alone doesn't prove a part bad, so confirm with a second measurement before replacing anything.
PPBUS_G3H0.45512.540181.000
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H — the name indicates a G3H ("always on") main bus rail, from the rail name itself; it's the board's main power bus.

  • Known-good readings from the archive: diode 0.455, voltage 12.540 V, resistance 181.000 (community values, a guide only; no condition is recorded).
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.455. Then apply power and measure the voltage, expecting about 12.54 V.
  • A diode reading far below known-good usually points to a short or a leaky part on the rail; a voltage far off points to the rail not coming up or being loaded down.
  • No known-good reading of other kinds is recorded here, so compare against a matching rail on a known-good board where possible.
PPBUS_G3H_SSD00.45512.540181.000
PPBUS_G3H_TPAD0.45512.540–
AI: what PPBUS_G3H_TPAD is and how to check it

PPBUS_G3H_TPAD — reference note

  • From the name, this is the PPBUS main bus rail feeding the trackpad section; the G3H suffix means it is an always-on rail present whenever the board has power.
  • Known-good readings in the archive: diode 0.455 and voltage 12.540. These are community values and a guide only; no known-good resistance reading here.
  • To check: power off and unplug, then diode mode from PPBUS_G3H_TPAD to ground. With power applied, measure the DC voltage on the rail.
  • A diode reading far from 0.455 usually points to a short or a leaky part on the rail; a voltage well off 12.540 suggests the bus is not coming up or is loaded down. Confirm with a second reading before suspecting a part.
PPBUS_G3H_TPAD_FLT0.45512.540–
PPBUS_G3H_TPAD_FUSED0.45512.540–
AI: what PPBUS_G3H_TPAD_FUSED is and how to check it
  • PPBUS_G3H_TPAD_FUSED is the main bus rail feeding the trackpad section, fused off the main PPBUS rail. From the name, G3H means it's always-on whenever the board has power, not gated by the power-on sequence.
  • Known-good readings here: diode 0.455 to ground and 12.540 V with power applied. These are community figures and a guide only.
  • To check it: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage.
  • A diode far below 0.455 suggests a short or leaky part on the rail; a voltage well off 12.540 V points to the fuse, the source rail feeding it, or a load pulling it down. No known-good resistance reading is recorded for this rail.
PPDCIN_G3H0.55016.5004.700R
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H — 820-01521 reference note

  • What it is: the main DC-input rail from the USB-C input stage. The "G3H" suffix means always-on (from the name), so it should be present whenever a charger is connected, before the board is switched on.
  • Known-good readings (community guide): diode 0.550 to ground, voltage 16.500 V, resistance 4.700R. These vary with the board's state, so treat them as a guide, not a spec.
  • How to check: with the board unpowered, measure diode mode from PPDCIN_G3H to ground; then apply the charger and measure the voltage on the rail. The notes also list it at Q3100 pin 8 and Q3200 pin 8, so those are handy probe points.
  • If it's far off: a diode reading well below 0.550 suggests a short or leaky part on the rail; no voltage with a charger connected points back to the input stage (F3000/F3001, Q3100/Q3200 and the CD3215 units). No known-good current-limited supply reading here, so compare against a matching point on the other input path.
PPDCIN_G3H_CHGR_AMON0.55019.8004.700R
AI: what PPDCIN_G3H_CHGR_AMON is and how to check it

PPDCIN_G3H_CHGR_AMON is a DC-in rail from the charger section, and the G3H part of its name indicates it is always-on, present whenever power is connected. The archived readings for this net are diode 0.550, voltage 19.800 and resistance 4.700R; treat these as a guide only, since they come from community contributions and vary with board state. Check it unpowered in diode mode to ground first, then power the board and measure the voltage, comparing against those values. A reading far from known-good usually points to a short or open on that rail or its feed, but one reading alone doesn't confirm a bad part. No known-good current-limited or load-condition reading is recorded here, so compare against a matching net or a known-good board if the plain values look off.

PPVBAT_G3H_CHGR_R0.45513.100181.000
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — the name indicates a battery/charger rail in the G3H (always-on) domain, so it should be present whenever the charger is connected, before the board is switched on. That's from the name only; the archive doesn't list which parts sit on this net.

Known-good readings from the archive: diode 0.455, voltage 13.100, resistance 181.000 (no condition given; community readings, so treat as a guide).

  • Power off and unplug, then diode-mode from the rail to ground; compare with 0.455.
  • With the charger connected, measure the voltage; compare with 13.100.
  • A short or much lower diode/resistance reading points to a fault on the rail itself; a missing voltage with a normal diode reading points upstream, toward the charger input path.

No known-good value is recorded for any other condition, so a matching net or a known-good board is the only cross-check.

PPVBAT_G3H_CONN0.87313,050–
AI: what PPVBAT_G3H_CONN is and how to check it
  • What it is: From the name, PPVBAT_G3H_CONN is the battery-voltage rail at the battery connector, in the always-on (G3H) domain. It should be present whenever a battery or charger is attached.
  • Known-good readings (community, guide only): diode 0.873, voltage 13,050 (about 13 V). No known-good resistance reading here.
  • How to check: Power off and unplug, then diode mode from PPVBAT_G3H_CONN to ground. Then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading or a collapsed voltage usually points to a short or heavy load on the rail; a missing voltage points to the battery/charger path feeding it. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_FUSE0.87313,050–
AI: what PPVBAT_G3H_FUSE is and how to check it

PPVBAT_G3H_FUSE — 820-01521

  • From the name, this is the fused battery-voltage rail in the G3H (always-on) group: battery power reaching the always-on section, after a fuse. It is not a regulated rail, so its voltage tracks the battery/charger input.
  • Known-good readings from the archive: diode 0.873 and voltage 13,050 (about 13 V). These are community values and only a guide; the data gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode reading far below 0.873 suggests a short or leaky load on the rail; far above it suggests an open path, such as a blown fuse or a broken trace. A voltage well under 13 V points to a supply or fuse problem upstream.
  • No known-good resistance reading exists for this rail.
PPVIN_G3H_P3V3G3H0.45512.540181.000
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H — reference note

  • This is the input rail feeding the G3H (always-on) 3.3 V supply; the "G3H" in the name marks it as an always-on stage, and "P3V3G3H" points to the 3.3 V always-on rail it supplies (from the name, not from a schematic).
  • Known-good readings from the community archive: diode 0.455, voltage 12.540 V, resistance 181.000. These are guides only and vary with board state.
  • To check: power off and unplug, then diode-mode from the rail to ground; then apply power and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a short or a leaky part on the rail; a voltage far off points to the upstream supply or enable not coming up. No known-good current-limited or loaded reading is available here, so compare against a matching rail on a known-good board.
PPVIN_G3H_P3V3G3HRTC0.45512.540181.000
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC — the "G3H" in the name marks it as an always-on (G3H) rail, and "P3V3" suggests a 3.3 V rail, though the name alone doesn't confirm the exact function.

  • Known-good readings from the archive: diode 0.455, voltage 12.540, resistance 181.000. These are community readings and only a guide; no condition is recorded.
  • To check: power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • A diode reading far from 0.455 usually points to a short or a damaged component on that net; a voltage far from 12.540 suggests the rail isn't coming up or is being pulled down.
  • No known-good reading of another kind is recorded here, so compare against a matching net or a known-good board before condemning a part.
PPVIN_G3H_P5VG3S0.45512.540181.000
AI: what PPVIN_G3H_P5VG3S is and how to check it
  • What it is: From the name, PPVIN_G3H_P5VG3S is a G3H (always-on) input rail, likely the 5V G3S input side. The name is the only description available.
  • Known-good readings (community archive, guide only): diode 0.455, voltage 12.540 V, resistance 181.000. No condition is recorded for these.
  • How to check: Power off and check diode mode to ground, then resistance; apply power and check the voltage.
  • If far off: A shorted or leaky load on the rail is the usual suspect, but that isn't confirmed. No known-good reading of another kind is listed here.

S5 and SUS: standby 8

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_SUS_PCH_VCCAPLL0.071––
AI: what PP1V_SUS_PCH_VCCAPLL is and how to check it
  • What it is: From the name, a standby (SUS) 1V rail feeding the PCH's VCCAPLL supply. It belongs to the S5 standby stage. The parts on this net aren't known here.
  • Known-good: diode 0.071 to ground (community reading, a guide only). No known-good voltage or resistance reading here.
  • How to check: Power off and unplugged, diode mode from the rail to ground; then power applied, measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail; a missing voltage with a normal diode reading points upstream to the standby supply. Confirm with a second reading before replacing anything.
PP1V_SUS_PCH_VCCCLK30.132––
AI: what PP1V_SUS_PCH_VCCCLK3 is and how to check it
  • What it is: From the name, PP1V_SUS_PCH_VCCCLK3 is a 1 V standby (SUS) rail feeding the PCH clock section. The "SUS" part places it in the standby stage.
  • Known-good reading: diode 0.132 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a second point on the same net before suspecting a part.
PP1V_SUS_PCH_VCCCLK40.131––
AI: what PP1V_SUS_PCH_VCCCLK4 is and how to check it
  • What it is: From the name, a 1V standby (SUS) rail feeding the PCH clock domain (VCCCLK4). It sits in the S5/standby startup stage.
  • Known-good: diode reading 0.131 in the archive (community value, a guide only; board state varies). No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or leaky load on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP1V_SUS_PCH_VCCCLK50.131––
AI: what PP1V_SUS_PCH_VCCCLK5 is and how to check it
  • What it is: From the name, a 1 V standby (SUS/S5) rail feeding the PCH clock domain (VCCCLK5). The name is the only description available.
  • Known-good: diode 0.131 to ground. No known-good voltage reading here.
  • How to check: power off, diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open feed. Confirm with a second measurement before replacing anything.
PP1V_SUSSW_PCH_VCCAMPHYPLL0.131––
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL is and how to check it
  • What it is: From the name, a 1V standby (SUS/S5) rail feeding the PCH camera/analog PLL supply. It sits in the standby stage, so it should be present before the board fully powers on.
  • Known-good reading: diode 0.131 (community value, guide only; board state affects it). No known-good voltage or resistance reading here.
  • How to check: power off, measure diode mode from the rail to ground, then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open trace or missing part. Confirm with a second measurement before replacing anything.
PP1V8_S50.3481.800–
AI: what PP1V8_S5 is and how to check it

PP1V8_S5 is a 1.8 V rail; the S5 suffix (from the name) puts it in the standby stage, so it should be present before the board fully powers on.

  • Known-good readings from the archive: diode 0.348 to ground, voltage 1.800 V. These are community values and a guide only; the data gives no condition for them.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.348.
  • Then power up and measure the voltage at the rail; expect about 1.800 V.
  • A diode reading far below known-good often suggests a short or a leaky part on the rail; a voltage well off 1.800 V points to the rail not coming up or being loaded down. No known-good resistance reading is listed here.
PP3V3_S50.34––
AI: what PP3V3_S5 is and how to check it
  • PP3V3_S5 is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage rail (from the name).
  • Known-good: diode 0.34 to ground. No known-good voltage reading here.
  • Check with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading far from 0.34 suggests a short or a leaky load on the rail; confirm with a second measurement before replacing anything.
PP5V_S5_LDO0.4805.000–
AI: what PP5V_S5_LDO is and how to check it

PP5V_S5_LDO — reference note

  • From its name, this is a 5 V standby (S5/SUS) low-dropout rail, present in the standby stage before the board fully powers on.
  • Known-good readings for this board: diode 0.480 to ground and 5.000 V with power applied. These are community readings and only a guide; no known-good resistance value is listed here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage.
  • A diode reading far below 0.480 suggests a short or leaky load on the rail; a voltage well off 5.000 V with a normal diode reading points more to the LDO source or its enable. Confirm with a second measurement before replacing anything.

S3: memory 7

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V_S30.248––
AI: what PP1V_S3 is and how to check it

PP1V_S3 is the 1 V S3 rail; the "S3" in its name places it in the memory stage of startup (this is from the rail name, not from schematic data). The only known-good figure here is a diode reading of 0.248 to ground. With the board unpowered, measure in diode mode from PP1V_S3 to ground and compare; then apply power and check the voltage is present when the board reaches S3. No known-good voltage reading exists here. A diode value far from 0.248 usually points to a short or a damaged component on that rail, but one reading isn't proof, so confirm with a second measurement before replacing anything.

PP1V2_S30.2201.200220.000
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 — 1.2 V S3 rail (reference note)

  • The name indicates a 1.2 V rail that comes up in the S3 (memory) startup stage; that reading is from the name, not from a schematic.
  • Known-good readings for this net: diode 0.220, voltage 1.200, resistance 220.000. These come from community contributions and are a guide only; no condition is recorded.
  • Check it unpowered in diode mode to ground first, then measure the voltage with the board powered. No known-good reading of any other kind exists here.
  • A diode or resistance far below known-good usually suggests a short or a leaky part on the rail; far above can mean an open feed or a missing enable. Confirm with a second measurement before replacing anything.
PP1V8_S30.331.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix, from its name, places it in the memory startup stage. Known-good readings for this board: diode 0.33 and voltage 1.800 (community guide, no condition given).

  • Check it unpowered in diode mode from the rail to ground; expect about 0.33.
  • Then power the board and measure the rail voltage; expect about 1.800 V.
  • A diode reading far below 0.33 suggests a short or a failing load on the rail; a voltage well off 1.8 V points to the rail not coming up or being loaded down.

No known-good resistance reading is available here, so compare against a matching net or a known-good board if needed.

PP5V_S3_CPUVR_VCC0.4245.000–
AI: what PP5V_S3_CPUVR_VCC is and how to check it
  • PP5V_S3_CPUVR_VCC is a 5 V rail; from its name it belongs to the S3 (memory) startup stage and feeds the CPU VR (voltage regulator) area. The name is the only source for that, not a schematic.
  • Known-good readings from the archive: diode 0.424 and voltage 5.000. These are community values and vary with board state.
  • Check it with the board unpowered in diode mode, black probe to ground, red on the rail; then power up and measure the voltage.
  • A diode reading far from 0.424 suggests a short or a damaged part on that rail; a missing or low 5 V with power applied points to the rail not coming up, so trace its enable and source next.
  • No known-good resistance reading is recorded for this rail.
PPVREF_S3_MEM_VREFCA0.717––
AI: what PPVREF_S3_MEM_VREFCA is and how to check it
  • What it is: From the name, a memory reference voltage that comes up in the S3 (suspend-to-RAM) stage. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.717 to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the net to ground and compare with 0.717. Then power on and measure the voltage; compare it with a matching memory reference net or a known-good board, since no voltage value is recorded.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open connection. One reading alone doesn't confirm a bad part.
PPVREF_S3_MEM_VREFDQ_A0.759––
AI: what PPVREF_S3_MEM_VREFDQ_A is and how to check it

PPVREF_S3_MEM_VREFDQ_A — reference note

  • From its name, this is a memory reference voltage (VREFDQ) in the S3 (memory) startup stage. The name suggests a DDR reference level rather than a main power rail.
  • Known-good from the readings archive: diode 0.759 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode from the net to ground, then measure its DC voltage with power applied and compare against a known-good board of the same model.
  • A diode reading far below 0.759 usually points to a short or a leaky part on that net; a reading well above it can mean an open path. Neither confirms a bad part on its own.
PPVREF_S3_MEM_VREFDQ_B0.759––
AI: what PPVREF_S3_MEM_VREFDQ_B is and how to check it
  • What it is: From the name, a memory reference-voltage rail (VREFDQ) that comes up in the S3 stage; the exact parts on it aren't listed in the available data.
  • Known-good reading: diode 0.759 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.759; then power on and measure the rail voltage, comparing against a known-good board since no voltage value is recorded.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail, but one reading isn't proof — trace the rail and compare before replacing anything.

S0: running 31

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.121––
AI: what PP0V6_S0_DDRVTT is and how to check it
  • What it is: PP0V6_S0_DDRVTT is a 0.6 V DDR termination rail, going by its name; the S0 part means it's active in the running state. That's general naming, not from this board's data.
  • Known-good reading: diode 0.121 to ground, from the community archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or a failed load on the rail, but confirm with a second measurement before replacing anything.
PP0V95_S0_CPUVCCIO_REG_R0.0960.950128.000
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it

PP0V95_S0_CPUVCCIO_REG_R is a 0.95 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "CPUVCCIO" suggests it supplies the CPU's I/O voltage (that part is from the name, not from board data).

  • Known-good readings from the archive: diode 0.096, voltage 0.950 V, resistance 128.000. These are community values and only a guide.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a short or a leaky part on the rail; a voltage well off 0.950 V with power applied points to the rail not regulating or being loaded down.
  • No known-good waveform or current reading here. Confirm any suspect reading against a matching rail or a known-good board before replacing parts.
PP1V_S0SW0.275––
AI: what PP1V_S0SW is and how to check it

PP1V_S0SW is a 1 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "SW" suggests a switched rail (both from the name, not from board data).

  • Known-good reading in the archive: diode 0.275 to ground. No known-good voltage or resistance value is listed here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.275 usually points to a short or a damaged component on that rail; a missing or wrong voltage with a normal diode reading points more toward the rail not being enabled or its source not coming up.

These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP1V2_S0SW0.319––
AI: what PP1V2_S0SW is and how to check it
  • PP1V2_S0SW is a 1.2 V rail; the "S0" in the name indicates the running (S0) power state, and "SW" suggests a switched rail. This is from the name only.
  • Known-good: diode reading to ground 0.319 (board unpowered). No known-good voltage reading is recorded here.
  • Check it with the board off in diode mode, red probe on ground, black on the rail; then power up and measure the voltage, expecting about 1.2 V.
  • A diode reading far from 0.319 usually points to a short or a damaged part on that rail, but one reading alone isn't proof; compare with a matching rail on a known-good board before replacing anything.
PP1V8_S0_SPKRAMP_AVDD0.3501.800–
AI: what PP1V8_S0_SPKRAMP_AVDD is and how to check it
  • What it is: From the name, a 1.8 V supply for the speaker amplifier's analog supply (AVDD), active in the S0 running state.
  • Known-good readings (community guide): diode 0.350 to ground, voltage 1.800.
  • How to check: Power off, measure diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a low diode reading suggests a short on the rail; no voltage with a normal diode reading points upstream to its enable or source. No known-good resistance reading here.
  • Unsure: exact source and parts on this net aren't known, so treat the cause as likely, not confirmed.
PP3V3_S0SW_LCD0.488––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD — from the name, a 3.3 V rail switched on in the S0 (running) state, feeding the LCD. The only known-good figure here is a diode reading of 0.488 to ground; no known-good voltage is listed.

  • With the board unpowered, measure diode mode from PP3V3_S0SW_LCD to ground and compare with 0.488. A near-zero reading suggests a short on the rail; a much higher one suggests an open path.
  • Then power the board and measure the voltage on the rail, ideally with the display connected and the board awake. No known-good voltage is recorded here, so compare against a matching rail on a known-good board.
  • A voltage that never comes up points to the switch that enables this rail or its upstream supply, not necessarily the rail itself.
PP3V3_TBT_X_S00.5203.300–
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is a 3.3 V rail; the S0 in its name indicates it belongs to the running (S0) state, and TBT suggests it feeds the Thunderbolt side (from the name only). Known-good for this rail: diode 0.520 to ground and 3.300 V with the board powered, both community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading well below 0.520 suggests a short or a leaky load on the rail; a voltage far from 3.300 V with power applied points to the rail not being enabled or being pulled down. No known-good resistance reading is recorded here.

PP3V3R1V8R1V5_S0_PCH_VCCHDA0.357––
AI: what PP3V3R1V8R1V5_S0_PCH_VCCHDA is and how to check it
  • What it is: From the name, a 3.3 V/1.8 V/1.5 V supply for the PCH's HDA (audio) section, active in the S0 (running) state. The name alone doesn't say which of the three voltages this net actually carries.
  • Known-good reading: diode 0.357 in the archive. No known-good voltage or resistance reading here.
  • How to check: power off, then diode mode from the net to ground and compare with 0.357. Then power on into S0 and measure the voltage at the net.
  • If far off: a much lower diode reading usually points to a short or a failed load on the rail; a much higher one to an open path. Treat it as a guide, not a confirmed fault.
PP5V_S0_BKLT_A0.442––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the 5 V backlight rail that comes up in the S0 (running) state, judging by its name. The only known-good reading here is a diode value of 0.442 to ground; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from PP5V_S0_BKLT_A to ground and compare with 0.442.
  • Then power the board and check the voltage on the rail once the board is in S0.

A diode reading far below 0.442 suggests a short or a leaky load on the rail; a much higher or open reading points to a broken path feeding it. Treat these as guides, not confirmed faults, and confirm with a second measurement before replacing anything.

PP5V_S0_BKLT_D0.441––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the 5 V backlight rail that comes up in the S0 (running) state, judging from the name. The only known-good reading here is a diode value of 0.441 to ground; there is no known-good voltage or resistance reading for this rail.

  • With the board unpowered, measure diode mode from PP5V_S0_BKLT_D to ground and compare with 0.441; a much lower reading suggests a short on the rail, a much higher one an open path.
  • Then apply power and check the voltage, which should be near 5 V once the board is in S0.
  • A missing 5 V with a normal diode reading points upstream, to the backlight enable and the supply feeding the rail, rather than to the rail itself.
PP5V_S0_CPUCORE10.427––
AI: what PP5V_S0_CPUCORE1 is and how to check it
  • What it is: From the name, PP5V_S0_CPUCORE1 is a 5 V rail feeding CPU core 1, active in the S0 (running) state.
  • Known-good reading: diode 0.427 to ground, from the archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading suggests a short or leak on the rail; a much higher one suggests an open path. Confirm with a second measurement before replacing anything.
PP5V_S0_CPUCORE20.427––
AI: what PP5V_S0_CPUCORE2 is and how to check it
  • What it is: PP5V_S0_CPUCORE2 is a 5 V CPU-core rail. The S0 in the name (from the name) means it belongs to the running state, so it should only come up once the board is fully on.
  • Known-good reading: diode 0.427 to ground, from the community archive. Treat it as a guide; it varies with board state. There is no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.427. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a diode reading well below known-good suggests a short or a failing part on the rail; a much higher one can mean an open connection. A missing 5 V with a good diode reading points upstream, to the enable or the supply that feeds it.
PP5V_S0_CPUGT10.427––
AI: what PP5V_S0_CPUGT1 is and how to check it
  • What it is: PP5V_S0_CPUGT1 is a 5V rail. The PP prefix means a power rail, 5V is its nominal level, and the S0 suffix means it belongs to the running state — all from the name. The CPUGT1 part suggests it feeds CPU-related circuitry, but that is inference from the name, not board data.
  • Known-good reading: diode 0.427 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.427. Then apply power and measure the voltage; it should sit near 5V in the S0 state.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Treat these as guides only and confirm before replacing anything.
PP5V_S0_CPUGT20.427––
AI: what PP5V_S0_CPUGT2 is and how to check it
  • What it is: PP5V_S0_CPUGT2 is a 5 V rail in the S0 (running) state, judged from its name. The name suggests it feeds CPU graphics-related circuitry, but that's general inference, not from board data.
  • Known-good reading: diode 0.427 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far from known-good: a much lower diode reading usually points to a short or a failing load on the rail; a much higher one to an open path. Treat 0.427 as a guide only, since community readings vary with board state, and confirm before replacing anything.
PP5V_S0SW_LCD0.566––
AI: what PP5V_S0SW_LCD is and how to check it
  • What it is: PP5V_S0SW_LCD is a 5 V switched LCD rail; the name indicates "S0" (running state) and "SW" (switched), so it's expected to come up only once the board is in S0, not in standby.
  • Known-good reading: diode 0.566 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.566; then power up and measure the voltage, expecting about 5 V once the board is in S0.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points to the rail's enable or switch not coming on. These are likely causes, not confirmed ones.
PPVCC_S0_CPU0.0070.80014.500R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — the CPU core power rail, active in the S0 (running) state, judging from the name.

  • Known-good readings from the archive: diode 0.007, voltage 0.800 V, resistance 14.500R. These are community values and vary with board state; treat them as a guide.
  • Check it with the board unpowered in diode mode to ground first, then measure the voltage with power applied.
  • A diode or resistance far below 14.500R usually points to a short or a leaky load on the rail; a voltage well off 0.800 V suggests the rail isn't regulating. No known-good value of another kind is recorded here.
  • A likely cause isn't a confirmed one — verify with a second measurement before replacing anything.
PPVCCGT_S0_CPU0.0051.52010.700R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU — the name indicates a CPU graphics rail (VCCGT) that is up in the S0 (running) state; that reading is from the name, not from a schematic.

  • Known-good readings here: diode 0.005, voltage 1.520 V, resistance 10.700R. These are community values and only a guide; the data gives no condition for them.
  • Check it with the board unpowered (charger and battery off) in diode mode from the rail to ground, then apply power and measure the voltage on the rail.
  • A diode or resistance far below known-good usually points to a short or a heavy load on the rail; far above can mean an open feed or a missing enable. No known-good waveform or current draw is listed for this rail.
  • A likely cause is not a confirmed one — confirm with a second measurement before replacing anything.
PPVCCGT_S0_CPU_PH10.0051.52012.000R
AI: what PPVCCGT_S0_CPU_PH1 is and how to check it

PPVCCGT_S0_CPU_PH1 — the name indicates a CPU graphics rail (VCCGT) in the S0 running state; the PH1 suffix suggests a switching-node phase of that supply. From the name only, it's a CPU graphics power rail, not a general logic rail.

  • Known-good readings (community archive, guide only): diode 0.005, voltage 1.520, resistance 12.000R. No condition is recorded with them.
  • Check with the board unpowered: diode mode from the rail to ground, then resistance to ground; compare with the 0.005 and 12.000R above.
  • Then power the board and measure the voltage, comparing with 1.520.
  • A diode or resistance far below known-good usually points to a short or a failed part on that rail; a voltage far off points to the supply not coming up. No known-good waveform or current reading is available here.
PPVCCGT_S0_CPU_PH20.0051.52012.000R
AI: what PPVCCGT_S0_CPU_PH2 is and how to check it
  • What it is: From the name, PPVCCGT_S0_CPU_PH2 is a CPU graphics-rail phase (PH2) that is active in S0 (running) state. It's a power rail, not a signal.
  • Known-good readings (community guide): diode 0.005, voltage 1.520 V, resistance 12.000R. These come from the readings archive and vary with board state; there's no stated condition.
  • How to check: Power off and unplug, then diode-mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far from known-good: a diode or resistance much lower than 0.005 suggests a short or a failing phase component; a missing or wrong voltage with power applied points to the rail not coming up. Confirm with a second reading before replacing anything.
PPVCCIO_S0_CPU0.0961.000–
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU — reference note

  • From its name, this is the CPU's S0 (running-state) I/O supply rail; the S0 suffix indicates it is expected only once the board is in its running power state.
  • Known-good readings for this board: diode 0.096 to ground, voltage 1.000 V. These come from community contributions and are a guide only; the data gives no condition for them.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode reading far from 0.096 usually points to a short or a damaged component on the rail; a correct diode reading with no voltage points more to the rail not being enabled or its source not coming up. No known-good resistance reading is available for this rail.
PPVCCSA_S0_CPU0.0171.520–
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU — reference note

  • From the name: a CPU power rail (VCCSA, system-agent supply) that is up in the S0 running state.
  • Known-good readings here: diode 0.017 and voltage 1.520. These come from community contributions and are a guide, not a spec; the data gives no condition for them.
  • To check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage. No known-good resistance reading exists here.
  • A diode far above 0.017 suggests an open or missing connection on the rail; far below suggests a short to ground. Confirm with the voltage before suspecting a part.
PPVCCSA_S0_CPU_R0.0171.52039.200R
AI: what PPVCCSA_S0_CPU_R is and how to check it

PPVCCSA_S0_CPU_R — the name indicates a CPU supply rail active in the S0 (running) state; the "SA" suffix usually means system-agent power on Intel designs, but that is general naming, not from this board's data.

Known-good readings for this rail (community guide, condition not stated): diode 0.017, voltage 1.520 V, resistance 39.200R.

To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.017; then apply power and measure the voltage, expecting about 1.520 V in S0. No known-good reading exists here for any other state.

A diode or resistance far below known-good points to a short or a leaky load on the rail; a voltage far off with a normal diode reading points more to the supply side. These are likely causes only, not confirmed — recheck with the board in the same state as the known-good readings before replacing anything.

PPVCCSA_S0_CPUDDR0.037––
AI: what PPVCCSA_S0_CPUDDR is and how to check it
  • What it is: PPVCCSA_S0_CPUDDR is a CPU/DDR supply rail; the "S0" in the name marks it as a running-state rail (from the name, not from board data).
  • Known-good reading: diode 0.037 to ground, from the community archive. It's a guide only, and no known-good voltage reading exists here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the rail voltage.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail; a missing voltage with a normal diode reading points to the rail's enable or supply.
PPVCORE_S0_CPU_PH10.0071.52014.500R
AI: what PPVCORE_S0_CPU_PH1 is and how to check it

PPVCORE_S0_CPU_PH1 — the name indicates the CPU core power rail (VCORE) for the CPU, in the S0 (running) state, on phase 1 (PH1) of its switching supply. This is general reading of the name, not from board data.

Known-good readings from the archive: diode 0.007, voltage 1.520 V, resistance 14.500R. These are community values and only a guide; the data gives no condition for them.

To check: with the board unpowered, measure diode mode from the rail to ground, then resistance to ground; then power the board and measure the voltage. A diode or resistance far below known-good suggests a short or a leaky load on the rail; a voltage far off 1.520 V points at the supply or its enable, not necessarily the CPU. No known-good waveform or ripple value here, so compare against a matching phase or a known-good board.

PPVCORE_S0_CPU_PH20.0071.52014.500R
AI: what PPVCORE_S0_CPU_PH2 is and how to check it

PPVCORE_S0_CPU_PH2 is a CPU core power rail; the S0 in the name indicates the running (S0) state, and PH2 likely marks a phase of the CPU core supply. The archive lists diode 0.007, voltage 1.520 and resistance 14.500R as community readings, so treat them as a guide only, not a guaranteed known-good value.

  • Check it unpowered in diode mode to ground, then again with power applied for the voltage.
  • A reading far from these usually points to a short or a failed phase on the core supply, but one reading alone doesn't confirm a bad part.
  • No known-good reading here is tied to a specific board condition, so compare against a matching phase or a known-good board before replacing anything.
PPVIN_S0_CPUVR_VIN0.46312.540–
AI: what PPVIN_S0_CPUVR_VIN is and how to check it

PPVIN_S0_CPUVR_VIN — the name indicates the input supply (VIN) for the CPU voltage regulator (CPUVR), in the S0 (running) state. It is a power rail, not a signal.

Known-good readings from the archive: diode 0.463 to ground, voltage 12.540 with the board powered. These are community values and a guide only.

To check it: power off and unplug, then measure in diode mode from the rail to ground. Then apply power and measure the voltage on the rail.

A diode reading far from 0.463 usually points to a short or a leaky part on that rail; a voltage well off 12.540 with power applied points to a supply or enable problem upstream. No known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT0.86644.000530.000
AI: what PPVIN_S0SW_LCDBKLT is and how to check it
  • PPVIN_S0SW_LCDBKLT is the backlight input rail for the LCD; the "S0" in the name indicates it belongs to the running (S0) power state, and "LCDBKLT" points to the display backlight circuit. This is from the name only.
  • Known-good readings for this net: diode 0.866, voltage 44.000, resistance 530.000. These are community readings and only a guide; the data gives no condition for them.
  • To check it: power off and unplug, then measure diode mode from the net to ground; then apply power and measure the voltage on the rail.
  • A diode or resistance far below known-good usually suggests a short or leaky part on the rail; a voltage far off with a normal diode reading points more toward the backlight driver or its enable. No known-good comparison exists for other states, so a matching net or a known-good board is the fallback.
PPVIN_S0SW_LCDBKLT_F0.45513.100–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F — the name indicates the input supply for the LCD backlight switch, in the S0 (running) state. From the name, it's the backlight rail's feed, not the backlight output itself.

  • Known-good readings here: diode 0.455, voltage 13.100 (no condition recorded).
  • Check with the board unpowered: diode mode, red probe on the net, black to ground. Then power up and measure the voltage on the same net.
  • A diode reading far below 0.455 suggests a short or leaky part on the rail; a missing or low voltage with power applied points to the supply feeding it or the switch not being enabled. These are likely causes, not confirmed ones.
  • No known-good resistance reading is recorded for this rail.
PPVIN_S0SW_LCDBKLT_R0.45513.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R — backlight input rail (from the name: S0 = running state, LCDBKLT = LCD backlight).

  • Known-good readings from the archive: diode 0.455 to ground, voltage 13.100 V. These are community values and only a guide; the conditions they were taken under aren't recorded.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • No known-good resistance reading is recorded here. For a comparison, use a matching rail on the other side of a pair or a known-good board.
  • A diode reading far below 0.455 suggests a short or leaky load on the rail; a much higher one suggests an open path. A voltage well off 13.100 V points at the backlight supply or its enable, not the rail itself. Confirm with a second measurement before replacing anything.
PPVOUT_S0_LCDBKLT1.101––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the display backlight output rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "LCDBKLT" indicates it feeds the panel backlight.

  • Known-good reading in the archive: diode mode to ground 1.101, with no condition noted.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage on the rail.
  • No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board rather than a fixed number.
  • A diode reading far below 1.101 usually points to a short or a leaky component on the rail; a far higher or open reading points to a broken connection. Confirm with a voltage check before replacing anything.
PPVOUT_S0_LCDBKLT_F1.101––
AI: what PPVOUT_S0_LCDBKLT_F is and how to check it
  • What it is: From its name, PPVOUT_S0_LCDBKLT_F is the display backlight output rail, active in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 1.101 (community value, a guide only; board state affects it). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 1.101; then power up and measure the DC voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail, but one reading doesn't confirm a bad part — compare against a known-good board before replacing anything.

Repair notes

CD3215 Repeat checks for each unit, U3100,3200, UB300, 400

U3100

1. Check 5V on F3000 pin 1 2. Check 3V3 on C3108 pin 1 1V8 on C3105 pin 1 1V8 on C3106 pin 1 1V1 on C3104 pin 1 3. Check 26V on Q3100 pin 1 and Q3100 pin 4 4. Check PPDCIN_G3H on Q3100 pin 8

U3200

1. Check 5V on F3001 pin 1 2. Check 3V3 on C3208 pin 1 1V8 on C3205 pin 1 1V8 on C3206 pin 1 1V1 on C3204 pin 1 3. Check 26V on Q3200 pin 1 and Q3200 pin 4 4. Check PPDCIN_G3H on Q3200 pin 8

CD3215 Sequence II

4. Check U6903 pin 10 3V3 (or 5V0) PM_EN_P3V3_G3H L6900 pin 2 3V3 PP3V3_G3H C5013 pin 1 1V2 PP1V2_G3H_SMC_VDDC C5167 pin 1 3V0 PP3V0_G3H_AVREF_SMC R3042 pin 1 3V3 (clock) SMBUS_SMC_4_G3H_SCL R3041 pin 1 3V3 (data) SMBUS_SMC_4_G3H_SDA C7016 pin 1 5V0 TBA_AUX_DET R7090 pin 2 3V3 SMC_RST_L D6902 pin 3 8V6/20V U7000 pin 10 P_IN U7000 pin 5 MPM_PBUS If still not finding anything, try ... Check TBA_VDDA and TBA_VDDP Measure R7075 for 4R7 value Check for EN (high) on PM_EN_P3V3_G3H Check 3V3 on R5940 pin 2 Check for EN (low) on HPWR_EN_L Check for EN (low) on SMC_WAKE_L (M13, WAKE_L) Check L5001 continuity and 3V3 Check R6915 continuity and 3V3

Every net with a reading

NetDiodeVoltageResistance
ACCEL_INT10.463––
ACCEL_INT20.464––
ALL_SYS_PWRGD0.739––
ALL_SYS_PWRGD_R0.495––
AUD_PWR_EN0.761.800–
BKLT_EN_R0.531––
BKLT_SD0.00––
BKLT_SENSE_OUT0.728––
BOARD_REV00.480––
BOARD_REV10.484––
BOARD_REV20.474––
BOOT_CONFIG00.480––
BOOT_CONFIG10.483––
BOOT_CONFIG20.479––
BT_DEV_WAKE0.457––
BT_HOST_WAKE0.468––
BT_PWR_EN0.471––
BT_ROM_BOOT_L0.476––
BTROM_HOLD_L0.644––
BTROM_WP_L0.643––
BTUARTMUX_OE_L0.482––
BTUARTMUX_SEL_PCH0.454––
CHGR_AMON0.615––
CHGR_AUX_DET0.61––
CHGR_BGATE0.61––
CHGR_BMON0.62––
CHGR_BOOT10.57––
CHGR_BOOT1_RC0.587––
CHGR_BOOT20.57––
CHGR_BOOT2_RC0.582––
CHGR_COMP0.60––
CHGR_CSI_N0.550–4.700R
CHGR_CSI_P0.550–4.700R
CHGR_CSIR_N0.55–3.000R
CHGR_CSIR_P0.55–3.000R
CHGR_CSO_N0.45513.100181.000
CHGR_CSO_P0.45513.100181.000
CHGR_CSOR_N0.42–3.000R
CHGR_CSOR_P0.42–3.000R
CHGR_EN_MVR0.535.000–
CHGR_EN_MVR_R0.5425.000–
CHGR_GATE_Q10.70––
CHGR_GATE_Q20.453––
CHGR_GATE_Q30.456––
CHGR_GATE_Q40.67––
CHGR_HPWR_EN_L0.00––
CHGR_LX10.45––
CHGR_LX20.45––
CHGR_PHASE10.45412.550276.000R
CHGR_PHASE20.45412.550–
CHGR_RST_IN0.60––
CHGR_RST_IN_R0.677––
CHGR_VBAT0.62––
CODEC_INT_L0.46––
CODEC_RESET_L0.46––
CODEC_WAKE_L0.46––
CPU_CATERR_L0.262––
CPU_CFG_RCOMP0.052––
CPU_CFG<0>0.307––
CPU_CFG<1>0.308––
CPU_CFG<2>0.307––
CPU_CFG<3>0.307––
CPU_CFG<4>0.289––
CPU_CFG<5>0.308––
CPU_CFG<6>0.307––
CPU_CFG<7>0.307––
CPU_CFG<8>0.306––
CPU_CFG<9>0.305––
CPU_CFG<10>0.306––
CPU_CFG<11>0.307––
CPU_CFG<12>0.308––
CPU_CFG<13>0.306––
CPU_CFG<14>0.307––
CPU_CFG<15>0.306––
CPU_CFG<16>0.309––
CPU_CFG<17>0.310––
CPU_CFG<18>0.306––
CPU_CFG<19>0.309––
CPU_DIMM_VREFCA0.721––
CPU_DIMMA_VREFDQ0.764––
CPU_DIMMB_VREFDQ0.762––
CPU_OPI_RCOMP0.051––
CPU_PECI0.313––
CPU_PROCHOT_L0.350––
CPU_PROCHOT_R_L0.311––
CPU_SM_RCOMP<0>0.195––
CPU_SM_RCOMP<1>0.085––
CPU_SM_RCOMP<2>0.163––
CPU_VCCGTSENSE_N0.002––
CPU_VCCGTSENSE_P0.011––
CPU_VCCIOSENSE_N0.001––
CPU_VCCIOSENSE_P0.101––
CPU_VCCIOSENSE_R0.105––
CPU_VCCIOSENSE_XW0.001––
CPU_VCCSASENSE_N0.001––
CPU_VCCSASENSE_P0.038––
CPU_VCCSENSE_N0.002––
CPU_VCCSENSE_P0.012––
CPU_VCCST_PWRGD0.549––
CPU_VCCST_PWRGD_R0.562––
CPU_VIDALERT_L0.302––
CPU_VIDALERT_R_L0.520––
CPU_VIDSCLK0.257––
CPU_VIDSCLK_R0.260––
CPU_VIDSOUT0.257––
CPU_VIDSOUT_R0.258––
CPU_VR_EN0.496––
CPU_VR_PROCHOT_L0.514––
CPUCORE_BOOT10.597––
CPUCORE_BOOT1_RC0.016––
CPUCORE_BOOT20.590––
CPUCORE_BOOT2_RC0.015––
CPUCORE_COMP0.625––
CPUCORE_COMP_RCOL––
CPUCORE_FB0.602––
CPUCORE_FB_RC1.168––
CPUCORE_FCCM0.602––
CPUCORE_GL10.460––
CPUCORE_GL20.455––
CPUCORE_IMON0.624––
CPUCORE_ISEN10.624––
CPUCORE_ISEN20.470––
CPUCORE_ISNS1_N0.0071.52014.500R
CPUCORE_ISNS1_P0.0071.52014.500R
CPUCORE_ISNS2_N0.0071.520–
CPUCORE_ISNS2_P0.0071.520–
CPUCORE_ISUMN0.013––
CPUCORE_ISUMN_R0.318––
CPUCORE_ISUMN_RCOL––
CPUCORE_ISUMP0.485––
CPUCORE_NTC0.625––
CPUCORE_NTC_ROL––
CPUCORE_PHASE10.007–11.600R
CPUCORE_PHASE20.007–14.500R
CPUCORE_PWM10.428––
CPUCORE_PWM20.610––
CPUCORE_RTN0.002––
CPUCORE_SENSE_P_R0.013––
CPUCORE_SENSE_P_RCOL––
CPUGT_BOOT10.596––
CPUGT_BOOT1_RC0.012––
CPUGT_BOOT20.597––
CPUGT_BOOT2_RC0.012––
CPUGT_BP10.00––
CPUGT_COMP0.626––
CPUGT_COMP_RCOL––
CPUGT_FB0.600––
CPUGT_FB_RC1.162––
CPUGT_FCCM0.603––
CPUGT_GL10.460––
CPUGT_GL20.480––
CPUGT_IMON0.627––
CPUGT_ISEN10.628––
CPUGT_ISEN20.626––
CPUGT_ISNS1_N0.0051.52012.000R
CPUGT_ISNS1_P0.0051.52012.000R
CPUGT_ISNS2_N0.0051.52012.000R
CPUGT_ISNS2_P0.0051.52012.000R
CPUGT_ISUMN0.011––
CPUGT_ISUMN_R0.268––
CPUGT_ISUMN_RC1.020––
CPUGT_ISUMP0.486––
CPUGT_NTC0.628––
CPUGT_NTC_ROL––
CPUGT_PHASE10.0051.5209.500R
CPUGT_PHASE20.0051.5209.500R
CPUGT_PWM10.613––
CPUGT_PWM20.610––
CPUGT_RTN0.002––
CPUGT_SENSE_P_R0.011––
CPUGT_SENSE_P_RCOL––
CPUSA_BOOT0.596––
CPUSA_BOOT_R0.596––
CPUSA_COMP0.624––
CPUSA_COMP_RCOL––
CPUSA_FB0.596––
CPUSA_FB_RCOL––
CPUSA_FCCM0.612––
CPUSA_IMON0.624––
CPUSA_ISNS_N0.0171.520–
CPUSA_ISNS_P0.0171.520–
CPUSA_ISUMN0.033––
CPUSA_ISUMN_R0.434––
CPUSA_ISUMN_RC1.040––
CPUSA_ISUMP0.573––
CPUSA_LGATE0.413––
CPUSA_LGATE_R0.413––
CPUSA_PHASE0.041––
CPUSA_PWM0.611––
CPUSA_RTN0.001––
CPUSA_SENSE_P_R0.033––
CPUSA_SENSE_P_RCOL––
CPUSA_SNUBR0.030––
CPUSA_SW_LL0.017–39.200R
CPUSA_UGATE0.524––
CPUSA_UGATE_R0.597––
CPUVR_PGOOD0.574––
CPUVR_PROG10.613––
CPUVR_PROG20.614––
CPUVR_PROG30.593––
CPUVR_PROG40.623––
CPUVR_PROG50.623––
CPUVR_VIDSCLK0.304––
CPUVR_VIDSOUT0.262––
CPUVSENSE_IN0.018––
DBGMUX_SWD_SOC_CLK0.459––
DBGMUX_SWD_SOC_IO0.460––
DP_INT_AUXCH_C_N0.273––
DP_INT_AUXCH_C_P0.270––
DP_INT_HPD0.789––
DP_INT_ML_C_N<0>0.272––
DP_INT_ML_C_N<1>0.267––
DP_INT_ML_C_N<2>0.270––
DP_INT_ML_C_N<3>0.269––
DP_INT_ML_C_P<0>0.274––
DP_INT_ML_C_P<1>0.270––
DP_INT_ML_C_P<2>0.270––
DP_INT_ML_C_P<3>0.270––
DP_X_SNK0_ML_C_N<0>0.282––
DP_X_SNK0_ML_C_N<1>0.284––
DP_X_SNK0_ML_C_N<2>0.284––
DP_X_SNK0_ML_C_N<3>0.283––
DP_X_SNK0_ML_C_P<0>0.281––
DP_X_SNK0_ML_C_P<1>0.292––
DP_X_SNK0_ML_C_P<2>0.283––
DP_X_SNK0_ML_C_P<3>0.285––
DP_X_SNK0_ML_N<0>0.476––
DP_X_SNK0_ML_N<1>0.476––
DP_X_SNK0_ML_N<2>0.475––
DP_X_SNK0_ML_N<3>0.475––
DP_X_SNK0_ML_P<0>0.485––
DP_X_SNK0_ML_P<1>0.479––
DP_X_SNK0_ML_P<2>0.478––
DP_X_SNK0_ML_P<3>0.480––
DP_X_SNK1_HPD0.594––
EDP_BKLT_EN0.531––
EDP_BKLT_PWM0.780––
EDP_PANEL_PWR_BUF_EN0.610––
EDP_PANEL_PWR_DLY_EN0.622––
EDP_PANEL_PWR_EN0.555––
ENET_CLKREQ_L0.478––
ESPI_CLK60M0.470––
ESPI_CLK60M_R0.491––
ESPI_CS_L0.470––
ESPI_IO_R<0>0.470––
ESPI_IO_R<1>0.470––
ESPI_IO_R<2>0.470––
ESPI_IO_R<3>0.470––
ESPI_IO<0>0.492––
ESPI_IO<1>0.490––
ESPI_IO<2>0.490––
ESPI_IO<3>0.489––
FAN_LT_PWM0.80––
FAN_LT_TACHOL––
GND0.000––
GND_5V3V3_AGND0.000––
GND_BKLT_SGND0.000––
GND_SMC_AVSS0.001––
HDA_SDOUT0.000––
I2C_ALS_SCL0.449––
I2C_ALS_SCL_CONN0.486––
I2C_ALS_SDA0.450––
I2C_ALS_SDA_CONN0.487––
I2C_BKLT_SCL0.513––
I2C_BKLT_SCL_R0.551––
I2C_BKLT_SDA0.512––
I2C_BKLT_SDA_R0.512––
I2C_DISP_LS_EN0.498––
I2C_DISP_SCL0.449––
I2C_DISP_SDA0.449––
I2C_FTCAM_ISOL_SCL0.730––
I2C_FTCAM_ISOL_SDA0.728––
I2C_FTCAM_SCL0.453––
I2C_FTCAM_SCL_CONN0.764––
I2C_FTCAM_SDA0.453––
I2C_FTCAM_SDA_CONN0.762––
I2C_PMU_SCL_R0.392––
I2C_PMU_SDA_R0.486––
I2C_PWR_SCL0.45––
I2C_PWR_SDA0.47––
I2C_SEP_SCL0.473––
I2C_SEP_SDA0.473––
I2C_SNS_G3S_SCL0.461––
I2C_SNS_G3S_SDA0.461––
I2C_SNS1_S0_SCL0.469––
I2C_SNS1_S0_SDA0.471––
I2C_SPKRAMP_L_SCL0.392––
I2C_SPKRAMP_L_SDA0.392––
I2C_SPKRAMP_R_SCL0.46––
I2C_SPKRAMP_R_SDA0.46––
I2C_TBT_X_SCL0.60––
I2C_TBT_X_SDA0.61––
I2C_TBT_XA_INT_L0.72––
I2C_TBT_XB_INT_L0.73––
I2C_TCON_SCL0.521––
I2C_TCON_SCL_CONN0.560––
I2C_TCON_SCL_R0.496––
I2C_TCON_SDA0.520––
I2C_TCON_SDA_CONN0.560––
I2C_TCON_SDA_R0.496––
I2C_TPAD_3V3_SCL0.903.300–
I2C_TPAD_3V3_SCL_R0.9793.300–
I2C_TPAD_3V3_SDA0.903.300–
I2C_TPAD_3V3_SDA_R0.994––
I2C_TPAD_SDA_R0.494––
I2C_UPC_SCL0.49––
I2C_UPC_SDA0.49––
I2C_UPC_XA_DBG_CTL_SCL0.55––
I2C_UPC_XA_DBG_CTL_SDA0.56––
I2C_UPC_XB_DBG_CTL_SCL0.762––
I2C_UPC_XB_DBG_CTL_SDA0.762––
I2S_CODEC_BCLK0.48––
I2S_CODEC_BCLK_R0.480––
I2S_CODEC_D2R0.46––
I2S_CODEC_LRCLK0.46––
I2S_CODEC_R2D0.48––
I2S_CODEC_R2D_R0.477––
I2S_SPKRAMP_L_BCLK0.393––
I2S_SPKRAMP_L_BCLK_R0.412––
I2S_SPKRAMP_L_D2R0.41––
I2S_SPKRAMP_L_D2R_R0.400––
I2S_SPKRAMP_L_LRCLK0.411––
I2S_SPKRAMP_L_LRCLK_R0.392––
I2S_SPKRAMP_L_R2D0.393––
I2S_SPKRAMP_L_R2D_R0.410––
I2S_SPKRAMP_R_BCLK0.48––
I2S_SPKRAMP_R_BCLK_R0.476––
I2S_SPKRAMP_R_D2R0.000––
I2S_SPKRAMP_R_LRCLK0.480––
I2S_SPKRAMP_R_LRCLK_R0.48––
I2S_SPKRAMP_R_R2D0.47––
I2S_SPKRAMP_R_R2D_R0.475––
IPD_LID_OPEN0.69––
ISNS_3V3G3HMAIN_IOUTOL––
ISNS_3V3G3HMAIN_N0.45513,100181.000
ISNS_3V3G3HMAIN_P0.45513,100181.000
ISNS_3V3G3HRTC_N0.45512.540181.000
ISNS_3V3G3HRTC_P0.45512.540181.000
ISNS_5VG3S_IOUTOL––
ISNS_5VG3S_N0.45513.100181.000
ISNS_5VG3S_P0.45513.100181.000
ISNS_HS_COMPUTING_IOUT0.681––
ISNS_HS_COMPUTING_N0.45513.100–
ISNS_HS_COMPUTING_P0.45513.100–
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.45513.100–
ISNS_LCDBKLT_P0.45513.100–
ISNS_SSD0_IOUTOL––
ISNS_SSD0_N0.45512.540181.000
ISNS_SSD0_P0.45512.540181.000
ISNS_TPAD_N0.45512.540–
ISNS_TPAD_P0.45512.540–
ISNS_VDDMAIN_IOUTOL––
ISNS_VDDMAIN_N0.382–389.600
ISNS_VDDMAIN_P0.382–389.600
ISNS_WLANBT_IOUTOL––
ISNS_WLANBT_N0.336–140.000
ISNS_WLANBT_P0.336–140.000
ITP_PMODE0.510––
JTAG_ISP_TCK0.595––
JTAG_ISP_TDI0.597––
JTAG_ISP_TDO0.600––
JTAG_TBT_X_TMS0.598––
JTAG_WLAN_SEL0.728––
KBD_BKLT_PWM0.519––
LCD_PWR_SLEW0.612––
LCD_PWR_SLEW_3V30.637––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.723––
LCDBKLT_FET_DRV0.566––
LCDBKLT_FET_DRV_R0.560––
LCDBKLT_SW0.441––
LCDBKLT_TB_XWR1.181––
LDO_CORE0.374––
LDO_RTC0.367––
LID_CTRL_DMIC0.679––
LID_OPEN_LEFT0.460––
LID_OPEN_RIGHT0.460––
MCP_EDP_RCOMP0.149––
MEM_A_CAA<6>0.185––
MEM_A_CAB<9>0.185––
MEM_A_CS_L<0>0.194––
MEM_A_CS_L<1>0.193––
MEM_A_ODT<0>0.192––
MEM_A_ZQ_A0.245––
MEM_A_ZQ_B0.245––
MEM_A_ZQ1_AOL––
MEM_A_ZQ1_BOL––
MEM_B_ZQ_A0.246––
MEM_B_ZQ_B0.246––
MEM_B_ZQ1_AOL––
MEM_B_ZQ1_BOL––
MEM_VREFCA_A_RC0.026––
MEM_VREFDQ_A_RC0.026––
MEM_VREFDQ_B_RC0.025––
MEMVTT_EN0.540––
MESA_INT0.46––
MESA_PWR_EN0.46––
MIPI_FTCAM_CLK_CONN_N0.762––
MIPI_FTCAM_CLK_CONN_P0.762––
MIPI_FTCAM_CLK_F_N0.762––
MIPI_FTCAM_CLK_F_P0.762––
MIPI_FTCAM_CLK_ISOL_N0.757––
MIPI_FTCAM_CLK_ISOL_P0.758––
MIPI_FTCAM_CLK_N0.517––
MIPI_FTCAM_CLK_P0.510––
MIPI_FTCAM_DATA_CONN_N<0>0.750––
MIPI_FTCAM_DATA_CONN_P<0>0.732––
MIPI_FTCAM_DATA_F_N<0>0.750––
MIPI_FTCAM_DATA_F_P<0>0.732––
MIPI_FTCAM_DATA_ISOL_N<0>0.748––
MIPI_FTCAM_DATA_ISOL_P<0>0.730––
MIPI_FTCAM_DATA_N<0>0.512––
MIPI_FTCAM_DATA_P<0>0.514––
MLB_RAMCFG10.790––
MOD_BT_ROM_BOOT_L0.700––
NAND_DISCHARGE_EN0.759––
NAND_DISCHARGE_EN_RC0.450––
NAND_RESET_L0.44––
NANDVSENSE_IN0.360––
P0V8SLPDDR_FB0.041––
P0V8SLPDDR_FB_R0.048––
P0V8SLPDDR_SW00.0420.80043.800R
P0V8SLPDDR_SW10.0420.80042.600R
P0V9SLPDDR_FB0.067––
P0V9SLPDDR_FB_R0.049––
P0V9SLPDDR_SW00.0670.90066.000R
P0V9SLPDDR_SW10.0670.90066.000R
P0V9SSD_FB_N0.002––
P0V9SSD_FB_P0.435––
P0V9SSD_SW00.3970.900396.200
P1V1_SLPDDR_SOCFET_EN0.572––
P1V1REG_AGND0.001––
P1V1SLPDDR_RAMP0.616––
P1V1SLPS2R_FB0.267––
P1V1SLPS2R_SW00.271.1001.870R
P1V1SLPS2R_SW10.271.1001.870R
P1V2_DRVH0.704––
P1V2_DRVH_R0.707––
P1V2_DRVL0.459––
P1V2_DRVL_R0.454––
P1V2_PHASE0.2201.200220.000
P1V2_SNS0.229––
P1V2_SW0.220––
P1V2_VBST0.624––
P1V2REG_MODE0.536––
P1V2REG_TRIP0.742––
P1V2REG_VREF0.643––
P1V2S0SW_RAMP0.696––
P1V8G3S_EN0.560––
P1V8G3S_SS0.613––
P1V8SLPS2R_FB0.387––
P1V8SLPS2R_SW00.3851,800140.000
P1V8SSD_FB0.372––
P1V8SSD_SW00.3731.8002.615R
P1VPRIM_FB0.486––
P1VPRIM_FB_R0.222––
P1VPRIM_SW00.0751.00074.500R
P1VPRIM_SW10.0751.00074.500R
P2V7_SSD_DISCHARGE0.3552.500–
P2V7NAND_EN0.557––
P2V7NAND_PGOOD0.523––
P2V7SSD0_AVIN0.442––
P2V7SSD0_EN0.557––
P2V7SSD0_FB1.383––
P2V7SSD0_FB_TOP0.374––
P2V7SSD0_PHASE0.3762.700373.000
P2V7SSD0_SS0.744––
P2V7SSD0_VOS0.384––
P3V3_TBT_X_SX_EN0.560––
P3V3G3H_AVIN0.462––
P3V3G3H_COMP20.7382.000–
P3V3G3H_COMP2_ROL––
P3V3G3H_CS2_L_N0.390–150.000
P3V3G3H_CS2_L_P0.4063.300150.000
P3V3G3H_CSP21.263––
P3V3G3H_DRVH0.943––
P3V3G3H_DRVH_R0.980––
P3V3G3H_DRVL0.548––
P3V3G3H_DRVL_R0.549––
P3V3G3H_FB1.383––
P3V3G3H_FB_ROL––
P3V3G3H_FB_TOP0.466––
P3V3G3H_PGOOD0.0903.300–
P3V3G3H_PHASE0.4533.3003.864R
P3V3G3H_RF0.582––
P3V3G3H_SNUBROL––
P3V3G3H_SS0.741––
P3V3G3H_SW0.3903.300–
P3V3G3H_VBST0.562––
P3V3G3H_VBST_R0.627––
P3V3G3H_VFB20.5831.000–
P3V3G3H_VFB2_R0.3903.300–
P3V3G3H_VFB2_R20.4003.300–
P3V3G3H_VFB2_RROL––
P3V3G3H_VOS0.470––
P3V3G3H_VSW0.3823.300150.000
P3V3G3S_EN0.57––
P3V3G3S_SS0.613––
P3V3MAIN_PGOOD0.574––
P3V3SEN_SS0.612––
P5VG3S_COMP10.7392.000–
P5VG3S_COMP1_ROL––
P5VG3S_CS1_L_N0.4245.000–
P5VG3S_CS1_L_P0.4335.000–
P5VG3S_CSP11.260––
P5VG3S_DRVH0.976––
P5VG3S_DRVH_R-0.998––
P5VG3S_DRVL0.549––
P5VG3S_DRVL_R0.549––
P5VG3S_EN0.567––
P5VG3S_EN_DLY0.501––
P5VG3S_EN_R0.563––
P5VG3S_PGOOD0.577––
P5VG3S_SNUBROL––
P5VG3S_SW0.4205.000–
P5VG3S_VBST0.62010.100–
P5VG3S_VBST_R0.62710.100–
P5VG3S_VFB10.5771.000–
P5VG3S_VFB1_R0.4245.000–
P5VG3S_VFB1_R20.4335.000–
P5VG3S_VFB1_RROL––
P5VG3S_VSW0.4085.0000.420R
P5VP3V3_SKIPSEL0.479––
P5VP3V3_VREF20.4792.000–
P5VP3V3_VREG30.509––
P5VXX_EN0.584––
PANEL_P3V3_EN0.571––
PANEL_P3V3_EN_D0.725––
PANEL_P5V_EN0.565––
PANEL_P5V_EN_D0.936––
PBUS_DIVIDER0.697––
PBUS_DIVIDER_OUT0.655––
PBUS_DIVIDER_REF0.659––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.43613.100–
PBUSVSENS_EN_L0.48612.070–
PBUSVSENS_EN_L_DIVOL12.200–
PCH_BT_ROM_BOOT_L0.658––
PCH_CLK24M_XTALIN0.802––
PCH_CLK24M_XTALOUT_R0.800––
PCH_DDPB_CTRLDATA0.774––
PCH_DDPC_CTRLDATA0.772––
PCH_DIFFCLK_BIASREF0.780––
PCH_GPP_A0_PU0.790––
PCH_INTRUDER_L0.818––
PCH_OPI_COMP0.051––
PCH_PCIE_RCOMP_N0.382––
PCH_PWRBTN_L0.7333.300–
PCH_RTC_RESET_L0.754––
PCH_SOC_SYNC0.483––
PCH_STRP_NO_REBOOT0.774––
PCH_UART_BT_D2R0.674––
PCH_UART_BT_R2D0.666––
PCH_UART_DEBUG_D2R0.748––
PCH_UART_DEBUG_R2D0.748––
PCH_USB2_COMP0.115––
PCH_WLAN_AUDIO_SYNC0.756––
PCH_WLAN_CLKREQ_L0.770––
PCH_WLAN_CLKREQ_R_LOL––
PCH_WLAN_DEV_WAKE0.727––
PCH_WLAN_PERST_L0.590––
PCIE_CLK100M_PCH_WLAN_C_N0.563––
PCIE_CLK100M_PCH_WLAN_C_P0.591––
PCIE_CLK100M_PCH_WLAN_CC_N0.565––
PCIE_CLK100M_PCH_WLAN_CC_P0.594––
PCIE_CLK100M_PCH_WLAN_N0.408––
PCIE_CLK100M_PCH_WLAN_P0.398––
PCIE_PCH_WLAN_D2R_C_N0.422––
PCIE_PCH_WLAN_D2R_C_P0.421––
PCIE_PCH_WLAN_D2R_CC_N0.422––
PCIE_PCH_WLAN_D2R_CC_P0.421––
PCIE_PCH_WLAN_D2R_N0.428––
PCIE_PCH_WLAN_D2R_P0.427––
PCIE_PCH_WLAN_R2D_C_N0.401––
PCIE_PCH_WLAN_R2D_C_P0.401––
PCIE_PCH_WLAN_R2D_CC_N0.500––
PCIE_PCH_WLAN_R2D_CC_P0.495––
PCIE_PCH_WLAN_R2D_N0.500––
PCIE_PCH_WLAN_R2D_P0.495––
PCIE_SOC_D2R_C_N<0>0.322––
PCIE_SOC_D2R_C_N<1>0.323––
PCIE_SOC_D2R_C_N<2>0.324––
PCIE_SOC_D2R_C_N<3>0.325––
PCIE_SOC_D2R_C_P<0>0.322––
PCIE_SOC_D2R_C_P<1>0.325––
PCIE_SOC_D2R_C_P<2>0.325––
PCIE_SOC_D2R_C_P<3>0.324––
PCIE_SOC_D2R_N<0>0.427––
PCIE_SOC_D2R_N<1>0.427––
PCIE_SOC_D2R_N<2>0.425––
PCIE_SOC_D2R_N<3>0.420––
PCIE_SOC_D2R_P<0>0.425––
PCIE_SOC_D2R_P<1>0.420––
PCIE_SOC_D2R_P<2>0.430––
PCIE_SOC_D2R_P<3>0.420––
PCIE_SOC_R2D_C_N<0>0.394––
PCIE_SOC_R2D_C_N<1>0.396––
PCIE_SOC_R2D_C_N<2>0.392––
PCIE_SOC_R2D_C_N<3>0.394––
PCIE_SOC_R2D_C_P<0>0.396––
PCIE_SOC_R2D_C_P<1>0.395––
PCIE_SOC_R2D_C_P<2>0.390––
PCIE_SOC_R2D_C_P<3>0.392––
PCIE_SOC_R2D_N<0>0.396––
PCIE_SOC_R2D_N<1>0.400––
PCIE_SOC_R2D_N<2>0.398––
PCIE_SOC_R2D_N<3>0.398––
PCIE_SOC_R2D_P<0>0.396––
PCIE_SOC_R2D_P<1>0.400––
PCIE_SOC_R2D_P<2>0.396––
PCIE_SOC_R2D_P<3>0.395––
PCIE_SSD0_D2R_C_N<0>0.329––
PCIE_SSD0_D2R_C_N<1>0.361––
PCIE_SSD0_D2R_C_P<0>0.329––
PCIE_SSD0_D2R_C_P<1>0.360––
PCIE_SSD0_D2R_N<0>0.400––
PCIE_SSD0_D2R_N<1>0.399––
PCIE_SSD0_D2R_P<0>0.397––
PCIE_SSD0_D2R_P<1>0.397––
PCIE_SSD0_R2D_C_N<0>0.292––
PCIE_SSD0_R2D_C_P<0>0.328––
PCIE_SSD0_R2D_N<0>0.403––
PCIE_SSD0_R2D_P<0>0.404––
PCIE_WAKE_L0.792––
PD_DP_X_SRC_HPD0.600––
PD_HIO_PWR_EN0.788––
PD_P1V2_S3_EN0.551––
PD_TBT_X_GPIO_00.610––
PD_TBT_XA_LSRX0.767––
PD_TBT_XA_LSTX0.735––
PD_TBT_XB_LSRX0.777––
PD_TBT_XB_LSTX0.800––
PD_USB_UPC_XA_FN0.740––
PD_USB_UPC_XA_FP0.600––
PDM_DMIC_CLK00.48––
PDM_DMIC_CLK0_R0.470––
PDM_DMIC_CLK10.48––
PDM_DMIC_CLK1_R0.470––
PDM_DMIC_DATA00.473––
PDM_DMIC_DATA0_ISOL0.51––
PDM_DMIC_DATA0_R0.496––
PDM_DMIC_DATA10.473––
PDM_DMIC_DATA1_ISOL0.51––
PDM_DMIC_DATA1_R0.495––
PHV_INT_XA_G3H0.628––
PHV_INT_XB_G3H0.630––
PLT_RST_3V3_L0.593––
PLT_RST_L0.526––
PM_MEMVTT_EN0.360––
PM_PCH_PWROK0.518––
PM_PCH_SYS_PWROK0.548––
PM_RSMRST0.722––
PM_RSMRST_L0.585––
PM_RSMRST_RC_L0.504––
PM_SLP_S0_L0.461––
PM_SLP_S3_L0.490––
PM_SLP_S4_L0.786––
PM_SLP_S5_L0.786––
PM_SYSRST_L0.780––
PM_SYSRST_R_L0.586––
PMU_ACTIVE_READY0.458––
PMU_CLK32K_PCH0.800––
PMU_CLK32K_PCH_1V00.818––
PMU_CLK32K_PCH_R0.766––
PMU_CLK32K_SOC0.490––
PMU_CLK32K_SOC_R0.524––
PMU_CLK32K_WLANBT_R0.515––
PMU_COLD_RESET_L0.459––
PMU_CPU_VSENSE0.578––
PMU_DROOP_L0.486––
PMU_IREF0.756––
PMU_LCDBKLT_ISENSE0.582––
PMU_LDO3_OUT0.474––
PMU_NAND_VSENSE0.577––
PMU_ONOFF_L0.689––
PMU_PVDDMAIN_EN0.7633.300–
PMU_RSLOC_RST_L0.663.300–
PMU_SYS_ALIVE0.394––
PMU_VCCIO_VSENSE0.574––
PMU_VDD_HI0.651––
PMU_VDD_MAX0.554––
PMU_VDDMAIN_ISENSE0.586––
PMU_WLANBT_ISENSE0.585––
PMU_XTAL10.791––
PMU_XTAL1_R0.791––
PMU_XTAL20.791––
PP0V6_S0_DDRVTT0.121––
PP0V8_SLPS2R0.230––
PP0V9_SE_VMID0.338––
PP0V9_SLPDDR0.0670.90066.000R
PP0V9_SLPDDR_SOC_PCIEREFBUF0.055––
PP0V9_SSD0.4250.900396.200
PP0V9_TBT_X_PCIE0.315––
PP0V9_TBT_X_SVR0.3050.900–
PP0V82_SLPDDR0.0420.80042.600R
PP0V95_S0_CPUVCCIO_REG_R0.0960.950128.000
PP1V_PRIM0.0751.00074.500R
PP1V_S0SW0.275––
PP1V_S30.248––
PP1V_SUS_PCH_VCCAPLL0.071––
PP1V_SUS_PCH_VCCCLK30.132––
PP1V_SUS_PCH_VCCCLK40.131––
PP1V_SUS_PCH_VCCCLK50.131––
PP1V_SUSSW_PCH_VCCAMPHYPLL0.131––
PP1V1_SLPDDR0.333––
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.353––
PP1V1_SLPDDR_SOC_XTAL_F0.352––
PP1V1_SLPS2R0.2701.1001.870R
PP1V1_UPC_XA_LDO_BMC0.5091.100–
PP1V1_UPC_XB_LDO_BMC0.5111.100–
PP1V2_AWAKE0.522––
PP1V2_AWAKE_SOC_PCIEPLL_F0.518––
PP1V2_AWAKE_SOC_PCIEREFBUF_F0.518––
PP1V2_AWAKE_SOC_PLLCPU_F0.521––
PP1V2_AWAKE_SOC_PLLSOC_F0.521––
PP1V2_S0SW0.319––
PP1V2_S30.2201.200220.000
PP1V8_ACCEL_FILTOL––
PP1V8_AWAKE0.3491.800–
PP1V8_AWAKE_SOC_FMON_F0.447––
PP1V8_AWAKE_SOC_TSADC_RC0.400––
PP1V8_G3S0.3171.800–
PP1V8_G3S_THMSNS_R0.333––
PP1V8_S0_SPKRAMP_AVDD0.3501.800–
PP1V8_S30.331.800–
PP1V8_S50.3481.800–
PP1V8_SE_AVDD0.314––
PP1V8_SE_ESE0.357––
PP1V8_SLPS2R0.3851.800140.000
PP1V8_SLPS2R_PMUVDDGPIO0.734––
PP1V8_SLPS2R_SOC_LPADC_RC0.436––
PP1V8_SLPS2R_SOC_LPOSC_RC0.449––
PP1V8_SSD0.3731.8002.615R
PP1V8_UPC_XA_LDOA0.5191.800–
PP1V8_UPC_XA_LDOD0.4791.800–
PP1V8_UPC_XB_LDOA0.5201.800–
PP1V8_UPC_XB_LDOD0.4821.800–
PP1V25_SLPS2R_SMC_AVREF0.595––
PP2V7_NAND0.3572.500373.000
PP3V_G3H0.4713.000–
PP3V3_AWAKE0.637––
PP3V3_G3H0.3823.300150.000
PP3V3_G3H_DEBUGLED_ROL––
PP3V3_G3H_DEBUGLED_RROL––
PP3V3_G3H_IPD_F0.3823.300–
PP3V3_G3H_PMU_VDDMAIN0.382–389.600
PP3V3_G3H_RTC0.4533.300–
PP3V3_G3H_RTC_R0.4533.3003.864R
PP3V3_G3S0.3363.300140.000
PP3V3_G3S_G3H_RIO0.40––
PP3V3_G3S_IPD_F0.3363.300–
PP3V3_G3S_WLANBT0.336–140.000
PP3V3_G3SSW_SNS0.5443.300–
PP3V3_S0SW_LCD0.488––
PP3V3_S50.34––
PP3V3_TBT_X_ANA0.524––
PP3V3_TBT_X_ANA_PCIE0.502––
PP3V3_TBT_X_F0.5203.300–
PP3V3_TBT_X_LC0.558––
PP3V3_TBT_X_S00.5203.300–
PP3V3_TBT_X_SX0.530––
PP3V3_UPC_XA_LDO0.4993.300–
PP3V3_UPC_XB_LDO0.5023.300–
PP3V3R1V8R1V5_S0_PCH_VCCHDA0.357––
PP4V7_SE_TVDD0.341––
PP5V_G3S0.4085.0000.420R
PP5V_G3S_IPD_F0.4085.000–
PP5V_G3S_P1V1REG0.428––
PP5V_G3S_VCCIOPVCC0.411––
PP5V_G3S_VCCIOVCC0.411––
PP5V_MAIN_ALSCAM_F0.425––
PP5V_S0_BKLT_A0.442––
PP5V_S0_BKLT_D0.441––
PP5V_S0_CPUCORE10.427––
PP5V_S0_CPUCORE20.427––
PP5V_S0_CPUGT10.427––
PP5V_S0_CPUGT20.427––
PP5V_S0SW_LCD0.566––
PP5V_S3_CPUVR_VCC0.4245.000–
PP5V_S5_LDO0.4805.000–
PP20V_USBC_XA_VBUS0.1419.800–
PP20V_USBC_XA_VBUS_F0.14019.800–
PP20V_USBC_XB_VBUS0.1419.800–
PP20V_USBC_XB_VBUS_F0.14019.800–
PPBUS_G3H0.45512.540181.000
PPBUS_G3H_SSD00.45512.540181.000
PPBUS_G3H_TPAD0.45512.540–
PPBUS_G3H_TPAD_FLT0.45512.540–
PPBUS_G3H_TPAD_FUSED0.45512.540–
PPBUS_HS_CPU0.45512.540–
PPCHGR_VDDA0.44––
PPCHGR_VDDP0.43––
PPDCIN_G3H0.55016.5004.700R
PPDCIN_G3H_CHGR_AMON0.55019.8004.700R
PPVBAT_G3H_CHGR_R0.45513.100181.000
PPVBAT_G3H_CONN0.87313,050–
PPVBAT_G3H_FUSE0.87313,050–
PPVCC_PRIM_CORE0.096–95.700R
PPVCC_S0_CPU0.0070.80014.500R
PPVCCGT_S0_CPU0.0051.52010.700R
PPVCCGT_S0_CPU_PH10.0051.52012.000R
PPVCCGT_S0_CPU_PH20.0051.52012.000R
PPVCCIO_S0_CPU0.0961.000–
PPVCCSA_S0_CPU0.0171.520–
PPVCCSA_S0_CPU_R0.0171.52039.200R
PPVCCSA_S0_CPUDDR0.037––
PPVCORE_S0_CPU_PH10.0071.52014.500R
PPVCORE_S0_CPU_PH20.0071.52014.500R
PPVDDCPU_AWAKE0.0130.625–
PPVDDCPUSRAM_AWAKE0.3550.800358.400
PPVIN_G3H_P3V3G3H0.45512.540181.000
PPVIN_G3H_P3V3G3HRTC0.45512.540181.000
PPVIN_G3H_P5VG3S0.45512.540181.000
PPVIN_LDO_WLAN0.293––
PPVIN_S0_CPUVR_VIN0.46312.540–
PPVIN_S0SW_LCDBKLT0.86644.000530.000
PPVIN_S0SW_LCDBKLT_F0.45513.100–
PPVIN_S0SW_LCDBKLT_R0.45513.100–
PPVIN_SW_LCDBKLT_SW0.86644.000530.000
PPVOUT_S0_LCDBKLT1.101––
PPVOUT_S0_LCDBKLT_F1.101––
PPVREF_S3_MEM_VREFCA0.717––
PPVREF_S3_MEM_VREFDQ_A0.759––
PPVREF_S3_MEM_VREFDQ_B0.759––
PPVTT_VTTREF0.501––
PU_DEBUG_CLKREQ_L0.792––
PU_TBT_X_GPIO_10.611––
PU_U8510_40.700––
PU_U8510_120.705––
PVCCEDRAM_REFIN0.694––
PVCCIO_BOOT_RC0.554––
PVCCIO_DRVH0.528––
PVCCIO_DRVH_R0.577––
PVCCIO_DRVL0.439––
PVCCIO_DRVL_R0.460––
PVCCIO_EN0.754––
PVCCIO_LL0.103––
PVCCIO_LL_SNUBOL––
PVCCIO_PGOOD0.517––
PVCCIO_PHASE0.0960.950128.000
PVCCIO_VBST0.553––
PVCCIOS0_AGND0.000––
PVCCIOS0_CS_N0.096––
PVCCIOS0_CS_P0.096––
PVCCIOS0_EN0.770––
PVCCIOS0_EN_FILT0.756––
PVCCIOS0_EN_FILT_BUF0.550––
PVCCIOS0_EN_FILT_BUF_R0.550––
PVCCIOS0_EN_R0.800––
PVCCIOS0_FB0.492––
PVCCIOS0_FB_R0.135––
PVCCIOS0_FSEL0.521––
PVCCIOS0_RTN0.496––
PVCCIOS0_SREF0.519––
PVCCIOS0_VO0.509––
PVCCOIOS0_OCSET0.510––
PVCCPCOREPRIM_FB_N0.002––
PVCCPCOREPRIM_FB_P0.255––
PVCCPCOREPRIM_FB_R_N0.002––
PVCCPCOREPRIM_FB_R_P0.255––
PVCCPCOREPRIM_SW00.096–95.700R
PVCCPCOREPRIM_SW10.096–95.700R
PVCCPLLOC_EN0.566––
PVDDCPUAWAKE_FB0.012––
PVDDCPUAWAKE_FB_XW0.000––
PVDDCPUAWAKE_SW00.0130.625–
PVDDCPUAWAKE_SW10.0130.62512.000R
PVDDCPUAWAKE_SW20.0130.62512.000R
PVDDCPUAWAKE_SW30.0130.62512.000R
PVDDCPUSRAMAWAKE_FB0.353––
PVDDCPUSRAMAWAKE_SW00.3550.800358.400
PVDDQ_EN0.555––
PVDDQ_EN_R0.553––
PVDDQ_PGOOD0.574––
PVIN_LDO_WLAN_L0.293––
PVIN_LDO_WLAN_LC0.293––
PVTT_VTTSNS0.127––
PVTT_VTTSNS_R0.127––
RF_0_ANTOL––
RF_0_ANT_MATCH_T0.000––
RF_1_ANTOL––
RF_1_ANT_MATCH_T0.000––
RF_A_0_DIPLEXER0.000––
RF_A_0_MATCH0.000––
RF_A_1_DIPLEXER0.000––
RF_A_1_MATCH0.000––
RF_G_0_DIPLEXER0.000––
RF_G_0_MATCH0.000––
RF_G_1_DIPLEXER0.000––
RF_G_1_MATCH0.000––
RTD3_PWR_EN0.600––
SAF_SEL_S0.840––
SAVE_BAT_G0.762––
SAVE_BAT_S1.563––
SAVE_CC1A_BOL––
SAVE_CC1A_G0.800––
SAVE_CC1B_BOL––
SAVE_CC1B_G0.788––
SAVE_CC1B_ZOL––
SAVE_CC2A_BOL––
SAVE_CC2A_G0.799––
SAVE_CC2A_Z0.460––
SAVE_CC2B_BOL––
SAVE_CC2B_G0.790––
SE_CTLR_FW_DWLD0.480––
SE_DEV_WAKE0.480––
SE_PWR_EN0.729––
SENSOR_PWR_EN0.559––
SEP_CAM_DISABLE_L0.456––
SEP_CAM_DISABLE_OE_L0.752––
SEP_CAM_DISABLE_OUT_L0.684––
SEP_DISABLE_STROBE0.457––
SEP_DMIC_DISABLE_L0.458––
SMBUS_3V3_BATT_SCL0.6423.300–
SMBUS_3V3_BATT_SDA0.6423.300–
SMBUS_PCH_CLK0.770––
SMC_3V3G3HMAIN_ISENSE0.807––
SMC_5VG3S_ISENSE0.806––
SMC_BMON_ISENSE0.802––
SMC_CPU_HS_ISENSE0.798––
SMC_DCIN_ISENSE0.801––
SMC_DCIN_VSENSE0.798––
SMC_FAN_0_PWM0.475––
SMC_LID_LEFT0.691.500–
SMC_LID_RIGHT0.701.500–
SMC_PBUS_VSENSE0.805––
SMC_PCH_PWROK0.458––
SMC_PCH_SYS_PWROK0.448––
SMC_PECI_RX0.436––
SMC_PECI_TX0.466––
SMC_PECI_TX_R0.465––
SMC_PROCHOT_L0.463––
SMC_RSMRST_L0.459––
SMC_SYSRST_L0.452––
SOC_AWAKE_BLUEOL––
SOC_CLKREQ_L0.779––
SOC_CLKREQ_R_L0.473––
SOC_COLD_RESET_L0.462––
SOC_DDR0_RREFOL––
SOC_DDR0_ZQ0.390––
SOC_DDR1_RREF0.555––
SOC_DDR2_RREF0.538––
SOC_DDR3_RREF0.553––
SOC_DDR3_ZQ0.593––
SOC_DFU_AMBEROL––
SOC_DFU_STATUS0.480––
SOC_DOCK_CONNECT0.461––
SOC_FORCE_DFU0.459––
SOC_HOLD_RESET0.454––
SOC_JTAG_SEL0.470––
SOC_MIPI0C_REXT0.800––
SOC_MIPI1C_REXT0.800––
SOC_MIPID_REXT0.800––
SOC_PCIE_DN_REXT0.778––
SOC_PCIE_STG0_REXT0.778––
SOC_PCIE_STG1_REXT0.778––
SOC_PCIE_UP_REXT0.777––
SOC_SLPDDR_GREENOL––
SOC_SLPS2R_REDOL––
SOC_SOCHOT_L0.457––
SOC_TESTMODE0.4555.000–
SOC_USB_REXT0.200––
SOC_USB_VBUS0.671––
SOC_VDDCPU_SENSE0.012––
SOC_XTAL24M_IN0.800––
SOC_XTAL24M_OUT0.795––
SOC_XTAL24M_OUT_R0.795––
SPI_ACCEL_CS_L0.465––
SPI_AOP_SENSOR_CLK0.490––
SPI_AOP_SENSOR_CLK_R0.470––
SPI_AOP_SENSOR_MISO0.475––
SPI_AOP_SENSOR_MOSI0.492––
SPI_AOP_SENSOR_MOSI_R0.470––
SPI_BT_CLK0.674––
SPI_BT_CS_L0.667––
SPI_BT_MISO0.619––
SPI_BT_MOSI0.626––
SPI_IO3_D0.760––
SPI_MESA_CLK0.48––
SPI_MESA_CLK_R0.475––
SPI_MESA_MISO0.46––
SPI_MESA_MOSI0.48––
SPI_MESA_MOSI_R0.477––
SPI_PCHROM_R_IO<3>0.765––
SPI_SOCROM_CLK0.475––
SPI_SOCROM_CLK_R0.477––
SPI_SOCROM_CS_L0.461––
SPI_SOCROM_MISO0.474––
SPI_SOCROM_MOSI0.464––
SPI_SOCROM_MOSI_R0.474––
SPI_SOCROM_MUX_MISO_R0.459––
SPI_SOCROM_WP_L0.535––
SPI_TPAD_3V3_CLK0.471––
SPI_TPAD_3V3_CLK_R0.467––
SPI_TPAD_3V3_CS_L0.6213.300–
SPI_TPAD_3V3_MISO0.6243.300–
SPI_TPAD_3V3_MOSI0.6243.300–
SPI_TPAD_3V3_MOSI_R0.617––
SPI_TPAD_CLK0.495––
SPI_TPAD_CLK_R0.480––
SPI_TPAD_CS_L0.431––
SPI_TPAD_MISO0.432––
SPI_TPAD_MISO_R0.439––
SPI_TPAD_MOSI0.447––
SPI_TPAD_MOSI_R0.463––
SPKR_ID00.46––
SPKR_ID10.46––
SPKRAMP_INT_L0.39––
SPKRAMP_L_AREG0.578––
SPKRAMP_L_BSTN0.771––
SPKRAMP_L_BSTP0.771––
SPKRAMP_L_DREG0.5001.200–
SPKRAMP_L_MODE0.000––
SPKRAMP_L_OUTN0.491–0.292R
SPKRAMP_L_OUTP0.491–0.292R
SPKRAMP_L_SNSN0.491––
SPKRAMP_RESET_L0.39––
SPKRCONN_L_OUTN0.491–0.292R
SPKRCONN_L_OUTP0.491–0.292R
SPMI_CLK0.480––
SPMI_CLK_R0.470––
SPMI_DATA0.40––
SPMI_DATA_R0.407––
SPT_XDP_PCH_OBSDATA_C00.793––
SPT_XDP_PCH_OBSDATA_C10.793––
SPT_XDP_PCH_OBSDATA_C20.793––
SPT_XDP_PCH_OBSDATA_C30.793––
SPT_XDP_PCH_OBSDATA_D00.793––
SSD_BFH0.421––
SSD_PMU_RESET_L0.456––
SSD0_CLK24M0.455––
SSD0_CLK24M_010.442––
SSD0_CLK24M_230.409––
SSD0_CLK24M_R0.450––
SSD0_CLKREQ0_L0.441––
SSD0_CLKREQ1_L0.442––
SSD0_CLKREQ2_L0.439––
SSD0_CLKREQ3_L0.459––
SSD0_LPB_L0.437––
SSD0_OCARINA_PFN0.394––
SSD0_PCIE_RESET_L0.421––
SSD0_RESET_L0.441––
SSD0_S4E_BOOT20.454––
SSD0_S4E_JTAG_SEL0.438––
SSD0_S4E_JTAG_TRST_L0.438––
SSD0_S4E0_AVDD18_PLL0.373––
SSD0_S4E0_DROOP_L0.491––
SSD0_S4E0_JTAG_TDO0.456––
SSD0_S4E0_PCI_AVDD_H0.373––
SSD0_S4E0_PCIE_RESREF0.778––
SSD0_S4E0_SWD_UID00.570––
SSD0_S4E0_SWD_UID10.476––
SSD0_S4E0_VPP0.554––
SSD0_S4E0_ZQ_C0.101––
SSD0_S4E0_ZQ_L0.303––
SSD0_S4E1_AVDD18_PLL0.372––
SSD0_S4E1_DROOP_L0.500––
SSD0_S4E1_JTAG_TDO0.454––
SSD0_S4E1_PCI_AVDD_H0.371––
SSD0_S4E1_PCIE_RESREF0.780––
SSD0_S4E1_SWD_UID00.488––
SSD0_S4E1_SWD_UID1OL––
SSD0_S4E1_VPP0.555––
SSD0_S4E1_ZQ_C0.107––
SSD0_S4E1_ZQ_L0.302––
SSD0_S4E2_AVDD18_PLL0.371––
SSD0_S4E2_JTAG_TDO0.478––
SSD0_S4E2_PCI_AVDD_H0.371––
SSD0_S4E2_VPP0.553––
SSD0_S4E2_ZQ_C0.101––
SSD0_SWCLK_UART_R2D0.425––
SSD0_SWDIO_UART_D2R0.423––
SSD0_WP_L0.372––
SYS_DETECTOL––
SYS_DETECT_L0.491––
SYS_DETECT_LEDOL––
SYS_STATE_BLUEOL––
SYS_STATE_BLUE_ROL––
SYS_STATE_GREENOL––
SYS_STATE_GREEN_ROL––
SYS_STATE_REDOL––
SYS_STATE_RED_ROL––
TBT_POC_RESET0.724––
TBT_PWR_AND_SX_EN0.558––
TBT_PWR_EN0.747––
TBT_WAKE_3V3_L0.608––
TBT_X_CIO_PWR_EN0.588––
TBT_X_CLKREQ_L0.488––
TBT_X_CLKREQ_R_L0.550––
TBT_X_PCI_RESET_L0.597––
TBT_X_PCIE_BIAS0.782––
TBT_X_PLUG_EVENT_L0.597––
TBT_X_RBIAS0.770––
TBT_X_ROM_HOLD_L0.700––
TBT_X_ROM_WP_L0.600––
TBT_X_RSENSE0.000––
TBT_X_SPI_CLK0.571––
TBT_X_SPI_CLK_DBG0.66––
TBT_X_SPI_CS_L0.604––
TBT_X_SPI_MISO0.608––
TBT_X_SPI_MOSI0.611––
TBT_X_TEST_PWR_GOOD0.101––
TBT_X_THERM_D_N0.001––
TBT_X_THERM_D_P0.645––
TBT_X_TMU_CLK_IN0.599––
TBT_X_TMU_CLK_OUT0.599––
TBT_X_USB_PWR_EN0.591––
TBT_XA_USB2_RBIAS0.202––
TBT_XB_USB2_RBIAS0.202––
THMSNS_ADDR0.640––
THMSNS_CHGR_D6_N0.000––
THMSNS_CHGR_D6_P0.640––
THMSNS_CPU_D1_N0.000––
THMSNS_CPU_D1_P0.640––
THMSNS_DRAM_D2_N0.000––
THMSNS_DRAM_D2_P0.040––
THMSNS_NAND_D5_N0.000––
THMSNS_NAND_D5_P0.640––
THMSNS_PMIC_D4_N0.000––
THMSNS_PMIC_D4_P0.641––
THMSNS_SOC_D3_N0.000––
THMSNS_SOC_D3_P0.639––
THMSNS_WLAN_D7_N0.000––
THMSNS_WLAN_D7_P0.641––
TP_BT_GPIO40.710––
TP_FAN_OTP1OL––
TP_FAN_OTP2OL––
TP_I2C_CODEC_SCL0.457––
TP_I2C_CODEC_SDA0.457––
TP_JTAG_SOC_TDI0.461––
TP_JTAG_SOC_TDO0.462––
TP_JTAG_SOC_TRST_L0.472––
TP_JTAG_WLAN_TCK0.739––
TP_JTAG_WLAN_TMS0.739––
TP_JTAG_WLAN_TRST0.738––
TP_P3V3G3H_EN20.584––
TP_PCH_LAN_WAKE_L0.793––
TP_Q3100_DRAIN0.576––
TP_Q3200_DRAIN0.573––
TP_SMC_DEBUGPRT_RX0.464––
TP_SMC_DEBUGPRT_TX0.464––
TP_SMC_FIXTURE_MODE_L0.461––
TP_SOC_DEBUGPRT_RX0.458––
TP_SOC_DEBUGPRT_TX0.458––
TP_SOC_VDDSOC_SENSE0.039––
TP_SOC_VSSCPU_SENSE0.001––
TP_SOC_VSSSOC_SENSE0.000––
TP_SSD0_S4E0_ANI0_VREF0.603––
TP_SSD0_S4E0_ANI1_VREF0.605––
TP_SSD0_S4E0_JTAG_TDI0.486––
TP_SSD0_S4E0_UART_TX0.481––
TP_SSD0_S4E1_ANI0_VREF0.593––
TP_SSD0_S4E1_ANI1_VREF0.599––
TP_SSD0_S4E1_UART_TX0.482––
TP_SSD0_S4E2_ANI0_VREF0.605––
TP_SSD0_S4E2_ANI1_VREF0.591––
TP_SSD0_S4E2_UART_TX0.476––
TP_USB_EXTC_N0.745––
TP_USB_EXTC_P0.744––
TP_USB_TPAD_VBUS_ENABLEOL––
TP_USB_TPADNOL––
TP_USB_TPADPOL––
TP_USB3_EXTB_D2R_N0.426––
TP_USB3_EXTB_D2R_P0.426––
TP_USB3_EXTB_R2D_C_N0.395––
TP_USB3_EXTB_R2D_C_P0.395––
TP_USBC_PP20V_XAOL––
TP_USBC_PP20V_XBOL––
TP_XDP_PCH_TCK0.424––
TPAD_3V3_ACTUATOR_DISABLE_L0.9751.500–
TPAD_ACTUATOR_DISABLE_L0.464––
TPAD_KBD_3V3_WAKE_L0.863.300–
TPAD_KBD_WAKE_L0.475––
TPAD_SPI_3V3_EN0.5683.300–
TPAD_SPI_3V3_INT_L0.863.300–
TPAD_SPI_EN0.433––
TPAD_SPI_INT_L0.460––
UART_BT_D2R0.460––
UART_BT_D2R_CTS_L0.460––
UART_BT_MUX_CTS_L0.598––
UART_BT_MUX_D2R0.612––
UART_BT_MUX_R2D0.601––
UART_BT_MUX_RTS_L0.608––
UART_SE_D2R0.473––
UART_SE_D2R_CTS_L0.472––
UART_SE_R2D0.472––
UART_SE_R2D_RTS_L0.473––
UART_WLAN_D2R0.473––
UART_WLAN_D2R_CTS_L0.475––
UNCONNECTED_183OL––
UPC_I2C_INT_L0.46––
UPC_PMU_RESET0.721––
UPC_X_SPI_CLK0.564––
UPC_X_SPI_CS_L0.587––
UPC_X_SPI_MISO0.588––
UPC_X_SPI_MOSI0.590––
UPC_XA_5V_EN0.767––
UPC_XA_DBG10.575––
UPC_XA_DBG20.576––
UPC_XA_FAULT_L0.755––
UPC_XA_GATE20.635––
UPC_XA_R_OSC0.521––
UPC_XA_SS0.524––
UPC_XA_UART_RX0.77––
UPC_XA_UART_TX0.77––
UPC_XB_5V_EN0.767––
UPC_XB_DBG30.477––
UPC_XB_DBG40.478––
UPC_XB_FAULT_L0.755––
UPC_XB_GATE10.647––
UPC_XB_GATE20.637––
UPC_XB_GPIO10.760––
UPC_XB_R_OSC0.521––
UPC_XB_SPI_CLK0.585––
UPC_XB_SPI_CS_L0.618––
UPC_XB_SPI_MISO0.622––
UPC_XB_SPI_MOSI0.559––
UPC_XB_SS0.525––
USB_DBG_PCH_XA_F_N0.714––
USB_DBG_PCH_XA_F_P0.714––
USB_SOC_N0.705––
USB_SOC_P0.705––
USB_UPC_PCH_XA_N0.714––
USB_UPC_PCH_XA_P0.714––
USB_UPC_PCH_XB_N0.707––
USB_UPC_PCH_XB_P0.707––
USB_UPC_XB_F_N0.707––
USB_UPC_XB_F_P0.707––
USB3_EXTA_D2R_N0.424––
USB3_EXTA_D2R_P0.424––
USB3_EXTA_R2D_N0.730––
USB3_EXTA_R2D_P0.730––
USBC_X_RESET_L0.755––
USBC_XA_CC10.593––
USBC_XA_CC1_CONN0.67––
USBC_XA_CC20.598––
USBC_XA_CC2_CONN0.67––
USBC_XA_D2R_CR_N<1>OL––
USBC_XA_D2R_CR_N<2>OL––
USBC_XA_D2R_CR_P<1>OL––
USBC_XA_D2R_CR_P<2>OL––
USBC_XA_R2D_N<1>OL––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<1>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_SBU10.81––
USBC_XA_SBU20.85––
USBC_XA_USB_DBG_BOT_N0.36––
USBC_XA_USB_DBG_BOT_P0.35––
USBC_XA_USB_DBG_TOP_N0.35––
USBC_XA_USB_DBG_TOP_P0.36––
USBC_XA_USB_TOP_N0.568––
USBC_XA_USB_TOP_P0.570––
USBC_XB_CC10.592––
USBC_XB_CC1_CONN0.67––
USBC_XB_CC20.599––
USBC_XB_CC2_CONN0.68––
USBC_XB_D2R_CR_N<1>OL––
USBC_XB_D2R_CR_N<2>OL––
USBC_XB_D2R_CR_P<1>OL––
USBC_XB_D2R_CR_P<2>OL––
USBC_XB_R2D_N<1>OL––
USBC_XB_R2D_N<2>OL––
USBC_XB_R2D_P<1>OL––
USBC_XB_R2D_P<2>OL––
USBC_XB_SBU10.80––
USBC_XB_SBU20.80––
USBC_XB_USB_BOT_N0.92––
USBC_XB_USB_BOT_POL––
USBC_XB_USB_TOP_NOL––
USBC_XB_USB_TOP_POL––
UVP_DIS_L0.57––
VCCIOVSENSE_IN0.153––
VR0V9_IND_TBT_X0.3050.900–
WIFI_SROM_STRAP0.736––
WLAN_AUDIO_SYNC0.452––
WLAN_CONTEXT_A0.462––
WLAN_CONTEXT_B0.462––
WLAN_HOST_WAKE0.461––
WLAN_PWR_EN0.473––
WLAN_ROM_CLK0.524––
WLAN_ROM_CS0.490––
WLAN_ROM_MISO0.523––
WLAN_ROM_MOSI0.495––
WLAN_ROM_ORG0.712––
WLAN_THROTTLE0.451––
XDP_BPM_L<0>0.305––
XDP_BPM_L<1>0.307––
XDP_BPM_L<2>0.307––
XDP_BPM_L<3>0.308––
XDP_CPU_PRDY_L0.282––
XDP_CPU_PREQ_L0.304––
XDP_CPUPCH_TCK0.052––
XDP_CPUPCH_TDI0.297––
XDP_CPUPCH_TDO0.259––
XDP_CPUPCH_TMS0.298––
XDP_CPUPCH_TRST_L0.299––
XDP_PCH_OBSDATA_A00.793––
XDP_PCH_OBSDATA_A10.793––
XDP_PCH_OBSDATA_A20.793––
XDP_PCH_OBSDATA_A30.793––
XDP_PCH_OBSDATA_B00.792––
XDP_PCH_OBSDATA_B10.793––
XDP_PCH_OBSDATA_B20.793––
XDP_PCH_OBSDATA_D10.793––
XDP_PCH_OBSDATA_D20.793––
XDP_PCH_OBSDATA_D30.793––
XDP_PCH_OBSFN_C10.788––
XDP_PRESENT_L0.426––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01521?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01521: diode 0.455, voltage 12.540, resistance to ground 181.000. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-01521?

OpenBoardData's known-good values for PP3V3_G3H on the 820-01521: diode 0.382, voltage 3.300, resistance to ground 150.000. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01521?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01521: diode 0.34. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01521 board?

Open your own 820-01521 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License