Apple laptop board · OpenBoardData

820-01041 known-good readings

Known-good readings for the Apple laptop board 820-01041: 438 nets, including 57 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 57 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01041.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 57 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 32

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.315––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is the 1.8 V rail that comes up in the G3S (always-on) stage, judging from its name and its place in the boot sequence after P1V8G3S_EN. The archive gives one known-good reading: diode mode to ground 0.315, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; the archive has no known-good voltage for this rail. A diode reading far from 0.315 points to a short or a damaged load on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V8_G3S_WLANBT_VDDIO0.336––
AI: what PP1V8_G3S_WLANBT_VDDIO is and how to check it

PP1V8_G3S_WLANBT_VDDIO — reference note

  • This is the 1.8 V I/O supply for the WLAN/Bluetooth section, from the name; the G3S part means it belongs to the G3S (always-on) group, and the boot sequence lists it after PP1V8_G3S.
  • Known-good: diode 0.336 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check with power off: diode mode, black probe to ground, red on the rail. Then power up and measure the DC voltage.
  • A diode reading far from 0.336 suggests a short or leaky part on that rail; a missing voltage with a good diode reading points upstream to its enable or source.
PP3V0_G3H_RTC0.480––
AI: what PP3V0_G3H_RTC is and how to check it

PP3V0_G3H_RTC — from the name, a 3.0 V always-on rail (G3H) feeding the RTC domain. It appears early in the boot sequence, right after PBUS and before PP3V3_G3H, so it should be present whenever a valid PSU, battery or charger is connected.

  • Known-good: diode mode to ground 0.480 (archive value, a guide only; no condition recorded).
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power up and measure the DC voltage; the archive has no known-good voltage for this rail, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far below 0.480 suggests a short or a leaky part on the rail; far above suggests an open trace or missing connection. Confirm with a voltage check before replacing anything.
PP3V3_G3H_RTC–3.300–
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC is the always-on 3.3 V rail that feeds the RTC section; the G3H part of the name indicates it should be present whenever the board has valid power (from the name and the boot sequence). The archive lists a known-good voltage of 3.300 V; there is no known-good diode or resistance reading here. Check it unpowered in diode mode to ground, then apply power and measure the voltage. A far-off voltage points to the rail's source or a short on it, but that's a likely cause, not confirmed.

PP3V3_G3H_RTC_ISOL–3.300–
AI: what PP3V3_G3H_RTC_ISOL is and how to check it
  • What it is: an always-on 3.3 V rail in the G3H (always-on) startup stage, judging by its name. The "_ISOL" suffix suggests an isolated branch of the RTC/G3H supply, but that's from the name only, not confirmed by board data.
  • Known-good reading: 3.300 V, with no condition listed. There is no known-good diode or resistance value for this rail here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a missing or low voltage points to the supply feeding it or a short on the rail, but that's a likely cause, not a confirmed one. Compare diode readings against the related PP3V3_G3H_RTC rail to judge whether the isolation branch itself is at fault.
PP3V3_G3H_RTC_REG_R0.3673.300–
AI: what PP3V3_G3H_RTC_REG_R is and how to check it

PP3V3_G3H_RTC_REG_R — reference note

  • This is the regulated 3.3 V rail feeding the RTC/always-on (G3H) domain, from its name; it sits early in the startup sequence, right after PPVIN_G3H_P3V3G3HRTC_R and CHGR_EN_MVR_R, and is listed as 3V3 at L6961 pin 2.
  • Known-good readings from the archive: diode 0.367 to ground, and 3.300 V with power applied. These are community values and a guide only.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail (L6961 pin 2). Then power up and measure DC voltage there.
  • A diode reading well below 0.367 suggests a short or leaky load on the rail; a correct diode reading with missing 3.3 V points back up the chain to the charger/regulator input side (PPVIN_G3H_P3V3G3HRTC_R, CHGR_EN_MVR_R).
  • No known-good resistance reading is recorded for this rail.
PP3V3_G3H_RTC_X0.3973.300–
AI: what PP3V3_G3H_RTC_X is and how to check it

PP3V3_G3H_RTC_X — reference note

  • From its name, this is the 3.3 V always-on (G3H) rail feeding the RTC section; it sits early in the boot sequence, right after PBUS and before PP3V3_G3H.
  • Known-good readings from the archive: diode 0.397 to ground, and 3.300 V with power applied. These are community values and a guide only.
  • Check it with the board unpowered in diode mode, black probe on ground, red on the rail; then power up and measure the voltage.
  • A diode reading far from 0.397 suggests a short or a leaky load on the rail; no voltage where 3.300 V is expected points to the rail not being enabled or its source missing. There is no known-good resistance value here, so compare against a matching rail or a known-good board.
PP3V3_G3H_SOCPMU–3.300–
AI: what PP3V3_G3H_SOCPMU is and how to check it

PP3V3_G3H_SOCPMU — 820-01041 reference note

  • What it is: a 3.3 V always-on rail feeding the SOC/PMU side, read from the name: "G3H" is the always-on domain and "SOCPMU" points at the SOC power-management section. The boot sequence lists PP3V3_G3H early, right after PBUS and PP3V3_G3H_RTC, so it should be present as soon as valid power is applied, before the S5/S3/S0 rails.
  • Known-good reading: 3.300 V, from the readings archive (no condition recorded). There is no known-good diode or resistance value for this net here.
  • How to check it: with the board unpowered, diode mode from the rail to ground for a short check, then apply power and measure the voltage at the rail. Compare the diode reading against a known-good board or a matching always-on 3.3 V rail, since no reference value is listed.
  • If it's far off: a missing or low 3.3 V here usually points upstream, to the always-on supply that generates it or its enable, rather than to the SOC. Confirm the earlier always-on rails (PP3V3_G3H_RTC, PP3V3_G3H) are good before suspecting anything on this net.
PP3V3_G3H_SSD0_SNS–3.300–
AI: what PP3V3_G3H_SSD0_SNS is and how to check it

PP3V3_G3H_SSD0_SNS — reference note

  • From its name, this is a 3.3 V sense line for the SSD0 rail in the G3H (always-on) domain; the "_SNS" suffix suggests it feeds back a divider or sense input rather than being a load rail itself. That reading of the name is general, not from board data.
  • Known-good: 3.300 V, with no condition recorded. There is no known-good diode or resistance reading for this net here.
  • To check it: power off and unplug, then diode mode from the net to ground and compare with a matching sense net or a known-good board; then apply power and measure the voltage.
  • A voltage well off 3.300 V points to the source rail or its divider/sense path, not necessarily the rail itself. Confirm with the source rail before replacing anything.
PP3V3_G3H_T–3.300–
AI: what PP3V3_G3H_T is and how to check it

PP3V3_G3H_T — the "G3H" part of the name indicates an always-on rail, present from the moment valid power is applied, before the board is switched on. The only known-good figure here is 3.300 V (voltage, no condition noted); there is no known-good diode or resistance reading for this net.

  • With the board unpowered, measure diode mode from the net to ground and note the value; there is no known-good number to compare against, so compare with a matching always-on rail or a known-good board.
  • Apply power and check for 3.300 V. A far-low or missing voltage points to the source feeding this rail or a short on the net, not necessarily to a single bad part.
  • This rail is not listed in the boot sequence notes, so its exact place in the sequence is uncertain; treat it as an early always-on rail.
PP3V3_G3S0.3003.300–
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is the 3.3V rail enabled by P3V3G3S_EN in the boot sequence; the "G3S" suffix means it stays on in the G3 (standby) state, so it's present before the board fully wakes. From the readings archive, known-good values are diode 0.300 and voltage 3.300; no condition is recorded for either.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.300.
  • With power applied, measure the voltage and compare with 3.300.
  • A voltage far from 3.300 points to the enable (P3V3G3S_EN) or the rail's supply not coming up; a diode reading well below 0.300 suggests a short or leaky load on the rail. These are guides only, and a single reading doesn't confirm a bad part.
PP3V3_G3S_TPAD0.3003.300–
AI: what PP3V3_G3S_TPAD is and how to check it

PP3V3_G3S_TPAD is the 3.3 V trackpad rail in the G3S (always-on) domain; the G3S stage comes from the rail name, and the TPAD suffix indicates it feeds the trackpad. Known-good readings from the archive: diode 0.300 to ground and 3.300 V with power applied (guide only, no condition given). Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.300 suggests a short or leaky load on the rail; a voltage well off 3.300 V points to the rail not being enabled or being pulled down. No known-good resistance reading is available here.

PP3V3_G3S_WLAN0.3543.300–
AI: what PP3V3_G3S_WLAN is and how to check it

PP3V3_G3S_WLAN — 820-01041

  • What it is: a 3.3 V rail for the WLAN section, from the name. The "G3S" part means it belongs to the G3S (suspend-to-RAM) group, so it's expected to be present while the board is in G3S rather than only at full power. The boot sequence lists P3V3G3S_EN and PP3V3_G3S before the WLAN clock (PMU_CLK32K_WLANBT), which fits that ordering.
  • Known-good readings (community archive, a guide only): diode 0.354 to ground, and 3.300 V with power applied. No condition is recorded with them.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power the board and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.354 suggests a short or a leaky load on the rail; a correct diode reading with no voltage points back to the enable (P3V3G3S_EN) or the upstream PP3V3_G3S. There's no known-good resistance value for this rail in the data, so compare against a matching rail or a known-good board.
PP3V3_G3S_X0.354––
AI: what PP3V3_G3S_X is and how to check it

PP3V3_G3S_X — reference note

  • What it is: a 3.3 V rail in the G3S group, from the name; G3S rails come up after the G3H always-on rails in the boot sequence, and the "_X" suffix is not explained in the available data.
  • Known-good reading: diode 0.354 to ground (community value, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If it's far off: a low diode reading usually points to a shorted load or capacitor on the rail, an open one to a missing connection. Confirm with a second measurement before replacing anything.
PP3V3_G3SSW_SNS0.4933.300–
AI: what PP3V3_G3SSW_SNS is and how to check it
  • What it is: PP3V3_G3SSW_SNS is a 3.3 V always-on rail; the "G3" in its name marks it as an always-on stage, and "SNS" suggests a sense line for that rail (from the name, not from board data).
  • Known-good readings: diode 0.493 and 3.300 V, with no condition recorded.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading or a missing 3.3 V usually points to a short or a rail that isn't coming up. No known-good resistance reading exists here, so compare against a matching rail or a known-good board before replacing anything.
PP5V_G3S0.3905.000–
AI: what PP5V_G3S is and how to check it

PP5V_G3S — reference note (820-01041)

  • What it is: a 5 V rail in the G3S group. The "G3S" part of the name indicates an always-on/standby rail, and the boot sequence lists it as coming up after P5VG3S_EN and before PP3V3_G3S and PP1V8_G3S. That reading is from the name and the sequence, not from a schematic.
  • Known-good readings (community archive, guide only): diode 0.390 to ground, and 5.000 V with the board powered. No condition is recorded with these values.
  • How to check: with the board unpowered, measure diode mode from PP5V_G3S to ground and compare with 0.390. Then apply power and measure the rail voltage, expecting about 5.000 V.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; no or wrong voltage with a normal diode reading points back to its enable (P5VG3S_EN) or the regulator feeding it. There is no known-good resistance reading here, so compare against a matching rail or a known-good board.
PP5V_G3S_DFR_FILT0.3905.000–
AI: what PP5V_G3S_DFR_FILT is and how to check it

PP5V_G3S_DFR_FILT — reference note

  • What it is: a 5 V rail in the G3S group, which from the name is a "G3S" (suspend-to-RAM / trickle) supply; "FILT" suggests a filtered branch of it. The name alone doesn't confirm what it feeds.
  • Known-good readings (community archive, guide only): diode 0.390 in diode mode, and 5.000 V with power applied. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage.
  • If it's far off: a low diode reading or a missing 5 V usually points to a short or a rail that isn't being enabled, not to the filter itself. Confirm with a second measurement before suspecting a part.
PP5V_G3S_VCCIOVCC0.390––
AI: what PP5V_G3S_VCCIOVCC is and how to check it

PP5V_G3S_VCCIOVCC — reference note

  • What it is: a 5 V rail in the G3S (always-on) group, from the name; the VCCIOVCC suffix suggests it feeds I/O supply on this board. The boot sequence lists PP5V_G3S as coming up after P5VG3S_EN and before the 3V3/1V8 G3S rails.
  • Known-good reading: diode 0.390 (community archive, no condition given). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage on the rail.
  • If it's far off: a low diode reading or missing 5 V usually points to a short or a failed source/enable upstream, but one reading isn't proof — confirm with a second measurement before replacing anything.
PPBUS_G3H0.35412.520–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H — 820-01041 reference note

  • What it is: the main bus rail from the charger side, present in the always-on G3H stage (from the rail name). It is the rail that feeds the downstream G3H converters.
  • Known-good readings (community guide): diode 0.354 to ground, and 12.520 V with power applied. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from PPBUS_G3H to ground; then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; correct diode but no or low voltage points back to the charger/PPBUS source and its enable, not to the rail itself.
PPBUS_G3H_SPKRAMP_RIGHT0.46013.100–
AI: what PPBUS_G3H_SPKRAMP_RIGHT is and how to check it

PPBUS_G3H_SPKRAMP_RIGHT — reference note

  • What it is: from the name, the main PPBUS rail feeding the right speaker amplifier; the G3H part means it is an always-on rail, present whenever the board has valid power.
  • Known-good readings (community archive, guide only): diode 0.460 to ground, voltage 13.100 V. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points upstream, at the source feeding PPBUS. Confirm with a second measurement before replacing anything.
PPBUS_G3H_SSD00.46013.100–
AI: what PPBUS_G3H_SSD0 is and how to check it

PPBUS_G3H_SSD0 — reference note

  • What it is: from the name, the "G3H" part marks an always-on rail, and "SSD0" places it in the SSD power path. The board data doesn't name the parts on this net.
  • Known-good readings (community guide): diode 0.460 to ground, and 13.100 V with power applied. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the net to ground; then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a missing or low voltage points to the upstream supply or enable for the SSD rail. Confirm with a second measurement before replacing anything.
PPBUS_G3H_SSD0_SNS0.409––
AI: what PPBUS_G3H_SSD0_SNS is and how to check it
  • What it is: From the name, a G3H (always-on) sense line for the main battery/PPBUS rail feeding SSD0. The data doesn't say which parts sit on it.
  • Known-good: diode 0.409 in the archive. No known-good voltage or resistance here.
  • How to check: power off, diode mode from the net to ground; then power on and measure its voltage.
  • If far off: usually points to a short or open on that rail or its sense path, but that's a likely cause, not confirmed. Compare against a matching net on the other side of a pair or a known-good board.
PPBUS_G3H_SSD1_SNS0.42512.600–
AI: what PPBUS_G3H_SSD1_SNS is and how to check it

PPBUS_G3H_SSD1_SNS — reference note

  • What it is: the "G3H" part of the name marks it as an always-on rail in the G3H startup stage; "SSD1_SNS" suggests it is the SSD-side sense line for the main PPBUS rail (from the name, not confirmed by data).
  • Known-good readings: diode 0.425 and 12.600 V, with no condition recorded. These come from community contributions and are a guide only.
  • How to check: power off and unplug, then diode mode from the net to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading points to a short or leaky part on the rail; a missing or low voltage points upstream to the PPBUS source or its enable. No known-good resistance reading exists here, so compare against a matching net or a known-good board before condemning anything.
PPDCIN_G3H0.53820.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H — reference note

  • What it is: the main DC input rail from the USB-C charger, in the always-on G3H startup stage (from the name). On this board it appears at Q3100, Q3200, QB300 and QB400 pin 8.
  • Known-good readings (community guide): diode 0.538 to ground, and 20.000 V with a valid charger connected. No known-good resistance reading here.
  • How to check: power off and unplug the charger, then diode mode from PPDCIN_G3H to ground. Reconnect the charger and measure the voltage.
  • If it's far off: a wrong diode reading suggests a short or leaky part on the rail; missing or low voltage points back to the USB-C input and 5V-to-20V negotiation path rather than the rail itself. Confirm with a second measurement before replacing anything.
PPDCIN_G3H_CHGR–5.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side input rail of the G3H (always-on) domain, judged from its name; it is the DC input the charger section works from. The archive lists one known-good reading: 5.000 V, with no condition given, and no diode or resistance value for this net.

  • With the board unpowered, measure diode mode from the net to ground and compare with a matching net on another USB-C channel; there is no known-good diode reading here.
  • With power applied, check the voltage at the points listed for PPDCIN_G3H (QB300 pin 8, QB400 pin 8, Q3100 pin 8, Q3200 pin 8) and expect about 5 V at the 5 V stage, rising toward 20 V once the CD3215 negotiates.
  • A reading far from 5 V at the 5 V stage points at the input path or the CD3215 LDOs before it; a missing 20 V points at negotiation or the gate drive. These are likely causes, not confirmed ones.
PPVBAT_G3H_CHGR_R0.35413.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R — reference note

  • What it is: a G3H (always-on) battery/charger rail, judged from the name; the "CHGR" part suggests it sits on the charger side of the battery path. The exact parts on it aren't documented here.
  • Known-good readings (community archive, guide only): diode 0.354 to ground, and 13.100 V with power applied.
  • How to check: power off and unplug, then diode-mode from the rail to ground; then apply power and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing or low voltage points upstream to the charger/battery path rather than the rail itself. No known-good resistance reading is listed here, so compare against a matching rail or a known-good board.
PPVBAT_G3H_CHGR_REG0.35413.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG — the name marks it as a G3H rail, meaning always-on while external power is present, and CHGR suggests it comes from the charger section. It is not in the boot sequence list, so its exact place in the power-up order isn't documented here.

  • Known-good from the archive: diode 0.354 to ground, voltage 13.100 V.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power up and measure the voltage on the rail.
  • A diode reading well below 0.354 suggests a short or a leaky part on the rail; a voltage far from 13.1 V points at the charger side not coming up. These are guides only, and no known-good resistance reading exists here.
PPVBAT_G3H_CONN0.880––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN — the name suggests a battery/backup supply for the G3H (always-on) domain, brought in at a connector; that meaning is from the name only, not from board data.

  • Known-good: diode-to-ground 0.880 (community reading, a guide only). No known-good voltage or resistance reading here.
  • Check with the board unpowered and battery/charger disconnected: meter in diode mode, black probe on ground, red on the net.
  • Then apply power and measure the voltage on the same net.
  • A diode reading far below 0.880 usually points to a short or leaky part on that net; far above suggests an open path. Confirm with a voltage check before replacing anything.
PPVIN_G3H_P3V3G3H0.46013.100–
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H — reference note

  • From the name, this is the always-on (G3H) input rail feeding the P3V3G3H always-on 3.3 V supply; it sits in the early startup stage, before the S5/S3/S0 rails.
  • Known-good readings from the archive: diode 0.460 to ground, and 13.100 V with power applied. These are community values and only a guide.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and measure the voltage.
  • A diode far from 0.460 suggests a short or leaky part on the rail; a voltage far from 13.100 V suggests the rail isn't coming up or is loaded down. No known-good resistance reading is listed here.
PPVIN_G3H_P3V3G3HRTC–13.100–
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it

PPVIN_G3H_P3V3G3HRTC — from the name, this is the always-on (G3H) input rail feeding the 3V3 G3H RTC regulator. It appears in the 5V-to-20V sequence as "13V PPVIN_G3H_P3V3G3HRTC_R at C6964 pin 1", so it's the input to the RTC 3V3 regulator, not the 3V3 output itself.

  • Known-good: 13.100 V (archive value, no condition given). The sequence step lists 13V at C6964 pin 1; the rail's own output, PP3V3_G3H_RTC_REG_R, is listed as 3V3 at L6961 pin 2.
  • Check: board unpowered, diode mode from the rail to ground; then power with a valid USB-C supply and measure the voltage. No known-good diode reading here, so compare against a matching net on another port or a known-good board.
  • A voltage well below ~13 V with the charger negotiated suggests the input path or the regulator's feed is not coming up; a short or very low diode reading to ground points to a fault on that rail. These are guides, not confirmed faults — check the upstream 20V VBUS and the CD3215 LDOs before condemning anything.
PPVIN_G3H_P3V3G3HRTC_R0.40512.000–
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it

PPVIN_G3H_P3V3G3HRTC_R — reference note

  • From its name, this is the input feed for the always-on G3H rail that supplies the RTC 3V3 regulator (PP3V3_G3H_RTC). It sits early in the power sequence, before the RTC rail comes up.
  • Known-good readings from the archive: diode 0.405 to ground, and 12.000 V with power applied. The 5V-to-20V sequence lists about 13 V at C6964 pin 1 as a guide; the exact figure depends on the charger and board state.
  • To check it: power off and unplug, then diode mode from the rail to ground. Power up with a known-good USB-C supply and measure the voltage.
  • A diode reading far from 0.405 usually points to a short or a leaky part on that rail; a voltage well below the expected figure points back to the charger input path or the USB-C front end. No known-good resistance reading here, so compare against a matching rail on the other side of the pair.
PPVIN_G3H_P5VG3S0.46013.100–
AI: what PPVIN_G3H_P5VG3S is and how to check it

PPVIN_G3H_P5VG3S — reference note (820-01041)

  • From the name, this is the input feed for the 5V G3S rail (PP5V_G3S in the boot sequence), in the always-on G3H domain. It sits after the main 5V-to-20V handshake, so it should only be present once the charger has negotiated and the G3H rails are up.
  • Known-good readings from the archive: diode 0.460 to ground, and 13.100 V with power applied. No condition is recorded for either, so treat them as a guide.
  • To check it: power off and unplug, then diode mode from the net to ground and compare with 0.460. Then apply power and measure the voltage, expecting about 13.1 V.
  • A diode reading well below 0.460 suggests a short or leaky part on the rail; a much higher one suggests an open feed. A missing or low voltage points back to the charger/PD stage or the enable that creates it, not necessarily to this rail itself.

S5 and SUS: standby 2

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.3303.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 — the name indicates a 3.3 V rail in the S5 (standby) state, so it should be present while the board is in standby, before full power-on. In the boot sequence it appears after PMU_ONOFF_L, alongside PP1V8_S5 and PPVPCORE_S5.

  • Known-good readings here: diode 0.330 to ground, voltage 3.300 V. No condition is recorded, so treat these as a guide.
  • Check with the board unpowered (charger and battery disconnected) in diode mode, black probe to ground, red on the rail; then apply power and measure the voltage.
  • A voltage far off 3.3 V, or a diode reading well below 0.330, usually points to a short or a rail not being enabled — but one reading alone doesn't confirm a bad part.
PPVPCORE_S50.255––
AI: what PPVPCORE_S5 is and how to check it

PPVPCORE_S5 is a standby (S5) core rail; the S5/SUS naming comes from the rail name and places it in the standby stage of the boot sequence, where it appears after PP3V3_S5 and PP1V8_S5.

  • Known-good: diode reading of 0.255 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail; then power the board and measure the voltage at the same point.
  • A diode reading far below 0.255 suggests a short or a leaky part on the rail; far above it suggests an open path. Confirm with a second measurement before replacing anything.

S4 3

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP5V_S4_T_USBC0.5055.000–
AI: what PP5V_S4_T_USBC is and how to check it

PP5V_S4_T_USBC — the name marks it as a 5V rail in the S4 startup stage, on the "T" side (the CD3215 USB-C path), so it's a USB-C-related 5V rail. The name is the only description available; which parts sit on the net isn't known.

Known-good readings from the archive: diode 0.505 and voltage 5.000 (no condition recorded).

  • With the board unpowered, measure diode mode from the rail to ground; compare with 0.505.
  • With power applied, measure the voltage; expect about 5.000 V.
  • A diode reading far below 0.505 suggests a short or a leaky load on the rail; a voltage well off 5 V points to the rail not being enabled or its source not coming up. No known-good resistance reading exists here, so compare against a matching net or a known-good board.
PP5V_S4_X_USBC0.4655.000–
AI: what PP5V_S4_X_USBC is and how to check it

PP5V_S4_X_USBC — the name indicates a 5V rail tied to the S4 stage (from the name), on the USB-C side of the board.

  • Known-good readings (archive): diode 0.465 to ground, voltage 5.000. No condition is recorded, so treat these as a guide only.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power the board and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or heavy load on the rail; a missing 5V with a normal diode reading points upstream, toward the USB-C power path and the S4 enable sequence rather than the rail itself. No known-good resistance reading exists for this rail.
PPVIN_S4_TPAD_FUSE–13.100–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE — the name suggests a fused input feed for the trackpad, enabled in the S4 stage (from the name; no parts list is available for this net).

  • Known-good: 13.100 V, with no condition recorded. No known-good diode or resistance reading exists here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage at the same point.
  • A voltage far below 13.1 V points to the fuse or its upstream feed; a low diode reading to ground suggests a short on the rail. Compare with a matching net on the other side of the pair before condemning anything.

S3: memory 4

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S30.1501.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail that, from its name, belongs to the S3 (suspend-to-RAM) stage of the power sequence. The board data lists it in the boot sequence after PP1V8_S3 and PVDDQ_EN, just before PVDDQ_PGOOD and PP1V_S3, so it should come up in that S3 group.

  • Known-good readings from the archive: diode 0.150 to ground, voltage 1.200. No condition is recorded, so treat these as a guide only.
  • To check: power off and unplug, then diode mode from PP1V2_S3 to ground and compare with 0.150. Then apply power and measure the rail; it should sit near 1.200 V once the S3 stage is reached.
  • A diode reading far below 0.150 suggests a short or a leaky load on the rail; a voltage that never appears points to the S3 enable or upstream stage rather than the rail itself. No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PP1V2_S3_REG_R0.1501.200–
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R — 820-01041 reference note

  • This is the 1.2 V S3 (suspend-to-RAM) regulator rail; the "S3" stage comes from its name, and the boot sequence lists PP1V2_S3 in the S3 group after PP1V8_S3 and PVDDQ_EN.
  • Known-good readings from the archive: diode 0.150 to ground, voltage 1.200 V. These are community values and a guide only.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good resistance reading is recorded here.
  • A voltage well off 1.200 V, or a diode reading far from 0.150, usually points to the rail not being enabled or loaded down; confirm its enable and upstream S3 rails before suspecting a part.
PP1V8_S30.4201.800–
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail that comes up in the S3 (memory) stage of the boot sequence, judging from its name; it appears after PP1V8_S5 and before PP1V2_S3 and PP1V_S3 in the sequence.

  • Known-good readings for this rail: diode 0.420 to ground, and 1.800 V when powered. No condition is recorded with them, so treat them as a guide.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A diode reading well below 0.420 suggests a short or a leaky load on the rail; a voltage far from 1.800 V with a normal diode reading points to the rail not being enabled or its source not running.
  • No known-good resistance reading exists here, so compare against a matching rail on a known-good board if needed.
PP1V8_S3_MEM0.4201.800–
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM — reference note

  • This is a 1.8 V memory rail that comes up in the S3 stage; the "S3" and "MEM" parts are read from the rail name, not from a schematic.
  • Known-good readings from the archive: diode 0.420 to ground, and 1.800 V with the board powered in S3. These are community values and only a guide.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.420. Then apply power and confirm 1.800 V once the board reaches S3.
  • A diode reading far below 0.420 suggests a short or leaky part on the rail; far above it suggests an open path. A missing or low voltage points to the rail's enable or regulator, so trace back through the S3 sequence before replacing anything.
  • No resistance reading is known-good for this rail here.

S0: running 16

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V95_S0_CPUVCCIO_REG_R0.0440.950–
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it

PP0V95_S0_CPUVCCIO_REG_R — the name indicates a 0.95 V CPU VCCIO rail, in the S0 (running) state, fed by a regulator. This is from the rail name, not from a schematic.

  • Known-good from the archive: diode 0.044 to ground, voltage 0.950 V. Community readings, so a guide only; no condition is recorded.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage.
  • A voltage far from 0.950 V with power applied points at the regulator or its enable, not the rail itself; a diode reading well below 0.044 suggests a short on the rail. No known-good resistance reading here, so compare against a matching rail or a known-good board.
PP3V3_S0SW_LCD0.553––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD — from the name, a 3.3 V rail that is switched (SW) and comes up in the S0 running state, feeding the LCD. It is not in the boot sequence listed here, so its exact position in the sequence is unknown.

  • Known-good: diode 0.553 to ground (from the readings archive, a guide only). No known-good voltage reading here.
  • Check unpowered: diode mode from the rail to ground and compare with 0.553.
  • Check powered: DC volts on the rail once the board is in S0.
  • A diode reading far below 0.553 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with the voltage before replacing anything.
PP3V3_S0SW_TBT_X_SNS0.500––
AI: what PP3V3_S0SW_TBT_X_SNS is and how to check it
  • What it is: PP3V3_S0SW_TBT_X_SNS is a 3.3 V S0 (running) rail tied to the Thunderbolt side, judging from its name; the data doesn't list which parts sit on it.
  • Known-good: diode 0.500 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the net to ground; then power on and measure the voltage.
  • If far off: a low diode reading usually points to a shorted part on that rail, but one reading isn't proof — compare with a matching net or a known-good board before replacing anything.
PP3V3_TBT_T_S00.5203.300–
AI: what PP3V3_TBT_T_S0 is and how to check it

PP3V3_TBT_T_S0 — the name indicates a 3.3 V rail for the Thunderbolt ("TBT") section, in the S0 (running) state; that reading is from the name, not from a schematic.

  • Known-good from the readings archive: diode 0.520 to ground, voltage 3.300 V. No condition is recorded, so treat these as a guide.
  • To check: power off and unplug, then diode mode from the rail to ground. Power up and confirm about 3.3 V.
  • A diode reading far below 0.520 suggests a short or leaky load on the rail; far above it suggests an open feed. Confirm with the voltage under power before condemning anything.
  • No known-good resistance reading here; compare against a matching rail on a known-good board.
PP5V_S0_ALSCAM_F0.404––
AI: what PP5V_S0_ALSCAM_F is and how to check it
  • What it is: PP5V_S0_ALSCAM_F is a 5V rail that, from its name, belongs to the camera supply and is enabled at the S0 (running) stage. The board data doesn't say which parts sit on it.
  • Known-good reading: diode 0.404 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.404; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. Readings vary with board state, so treat 0.404 as a guide, not a pass/fail limit.
PP5V_S0SW_LCD0.573––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD — the name indicates a 5 V rail that is switched on in the S0 (running) state and feeds the LCD. This is from the name only; the parts on the net aren't known.

  • Known-good diode reading: 0.573 (diode mode to ground, board unpowered). No known-good voltage reading here.
  • Check: power off, black probe to ground, red to the rail, diode mode — compare with 0.573. Then power on and measure the voltage at the rail.
  • A diode reading far below 0.573 suggests a short or leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PPVCC_S0_CPU–1.500–
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU — the name indicates a CPU core supply rail active in the S0 (running) state; that reading is from the name, not from a schematic.

  • Known-good: 1.500 V, from the archive. No diode or resistance value is recorded for this rail, so there is no known-good reading of that kind here.
  • To check: power off and unplug, then diode mode from the rail to ground. With power applied, measure the voltage — it should come up only after the S0 rails in the boot sequence, around PP1V2_S0SW, PP1V05_S0SW and PVCCIO_S0_CPU.
  • A voltage far from 1.500 V, or a diode reading very different from a matching rail on a known-good board, usually points to a short or a failed regulator — but confirm with a second measurement before replacing anything.
PPVCCEDRAM_S0_CPU0.0501.000–
AI: what PPVCCEDRAM_S0_CPU is and how to check it

PPVCCEDRAM_S0_CPU — the name indicates a CPU-side eDRAM supply that comes up in the S0 (running) state; that reading is from the name, not from a schematic.

  • Known-good from the archive: diode 0.050 to ground, voltage 1.000 V. No condition is recorded, so treat these as a guide only.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.050 suggests a short or leak on that rail; a voltage far from 1.000 V with the board in S0 points to the rail not being enabled or loaded down.
  • No known-good resistance reading exists here, so compare against a matching rail on a known-good board if you need one.
PPVCCEDRAM_S0_REG_R0.0501.000–
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R is a regulated supply rail for the eDRAM, active in the S0 (running) state, as the name indicates. The archive lists it as diode 0.050 and voltage 1.000, with no condition noted, so treat those as a guide only.

  • With the board unpowered, measure diode mode from the rail to ground and compare against 0.050.
  • With power applied and the board in S0, check the rail voltage against 1.000.
  • A diode reading well below 0.050 suggests a short or a leaky load on the rail; a missing or low voltage with a normal diode reading points to the regulator or its enable.

No known-good resistance reading is recorded for this rail.

PPVCCGT_S0_CPU–1.500–
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU — reference note

  • This is the CPU graphics rail (GT), from the name; the S0 suffix means it belongs to the running state, so it should only come up late in the boot sequence, after the S0 rails.
  • Known-good: 1.500 V with the board running. There is no known-good diode or resistance reading for this net here, so compare against a matching rail on a known-good board.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A voltage far from 1.5 V, or a diode reading clearly different from a known-good board, usually points to the rail's supply or its enable, not the CPU itself; confirm with the enable and supply pins before replacing anything.
PPVCCIO_S0_CPU0.0440.950–
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU — reference note

  • What it is: an S0 (running-state) CPU I/O supply rail; the S0 stage comes from the rail name. In the boot sequence it is enabled by PVCCIO_EN and sits just before PVCCIO_PGOOD and ALL_SYS_PWRGD, so it should only appear once the board is out of S5/S3.
  • Known-good readings (community guide): diode 0.044 to ground, voltage 0.950 V. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then apply power and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail, while missing voltage with a normal diode reading points back to its enable (PVCCIO_EN) or the upstream S0 rails. Treat this as a likely direction, not a confirmed fault.
PPVCCSA_S0_CPU–1.150–
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU — reference note

  • This is the CPU system-agent supply rail; the S0 in the name indicates it belongs to the running (S0) state, and the VCCSA part is the usual Intel name for the system-agent voltage. That meaning comes from the name, not from a schematic.
  • Known-good: 1.150 V with the board powered and in S0. No diode-mode or resistance reading is recorded for this rail, so there is no known-good reading of that kind here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with a known-good board or a matching rail on the other side of a pair. Then apply power, let the board reach S0, and measure the voltage.
  • A voltage far from 1.150 V in S0 points to the rail not being enabled or its regulator not regulating; a near-short in diode mode suggests a fault on the rail or its load. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT0.85012.900–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the display backlight input rail. The name suggests it is an S0 (running-state) switched supply feeding the LCD backlight, and that reading is from the name, not from a schematic.

  • Known-good readings here: diode 0.850 to ground, and 12.900 V with the board running.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the same point.
  • A diode reading well below 0.850 suggests a short or a leaky load on the rail; a correct diode reading with no or low voltage points upstream, at whatever switches the rail on, rather than at the load.
  • No known-good resistance reading is recorded for this rail.
PPVIN_S0SW_LCDBKLT_F0.460––
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it

PPVIN_S0SW_LCDBKLT_F — reference note

  • This is the input feed for the LCD backlight circuit, in the S0 (running) power state; that reading comes from the rail's name, not from board data.
  • Known-good: diode mode to ground 0.460, with no condition recorded. No known-good voltage or resistance reading here.
  • Check it with the board unpowered: meter in diode mode, black lead on ground, red on the rail. Then power up and measure the voltage on the same point.
  • A diode reading far below 0.460 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with a second measurement before suspecting a part.
PPVIN_S0SW_LCDBKLT_R0.460––
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it
  • What it is: From its name, PPVIN_S0SW_LCDBKLT_R is the input supply to the LCD backlight circuit, switched in the S0 (running) state. "PP" is a power rail, "VIN" the input, "S0SW" a switch enabled at S0, and "LCDBKLT" the display backlight.
  • Known-good reading: Diode mode to ground, 0.460. No known-good voltage reading for this rail here.
  • How to check: Power off and unplug, then diode mode from the rail to ground. Then power on and measure the voltage on the rail, ideally at the backlight connector or a nearby test point.
  • What a far-off diode reading suggests: A much lower reading points to a short or leaky part on the rail; a much higher one to an open path. Confirm with a voltage check before replacing anything.
PPVOUT_S0_LCDBKLT1.15355.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT — backlight output rail (S0 = running state, from the name). This is the boost converter output that drives the display backlight LED string; it only comes up once the board is in S0.

  • Known-good readings in the archive: diode mode to ground 1.153, and 55.000 V with power applied. These are community figures and vary with board state, so treat them as a guide.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage.
  • A diode reading far below 1.153 suggests a short or leaky part on the rail; a much higher one suggests an open path. No known-good resistance reading exists here, so compare against a matching backlight rail on a known-good board.
  • The 55 V is a boosted rail, so treat it with care — it can bite.

Repair notes

CD3215 USB-C Power

Fundemental power off checks

(U3100) 0V6 DM USBC_XA_CC1 at C3113 pin 1 0V6 DM USBC_XA_CC2 at C3114 pin 1 (U3200) 0V6 DM USBC_XB_CC1 at C3213 pin 1 0V6 DM USBC_XB_CC2 at C3214 pin 1 (UB300) 0V6 DM USBC_TA_CC1 at CB313 pin 1 0V6 DM USBC_TA_CC2 at CB314 pin 1 (UB400) 0V6 DM USBC_TB_CC1 at CB413 pin 1 0V6 DM USBC_TB_CC2 at CB414 pin 1

Chip voltages

UB300 1. Check 5V on FB200 pin 1 2. Check 3V3 on CB308 pin 1 1V8 on CB305 pin 1 1V8 on CB306 pin 1 1V1 on CB304 pin 1 3. Check 26V on QB300 pin 1 and QB300 pin 4 4. Check PPDCIN_G3H on QB300 pin 8 UB400 1. Check 5V on FB201 pin 1 2. Check 3V3 on CB408 pin 1 1V8 on CB405 pin 1 1V8 on CB406 pin 1 1V1 on CB404 pin 1 3. Check 26V on QB400 pin 1 and QB400 pin 4 4. Check PPDCIN_G3H on QB400 pin 8 U3100 1. Check 5V on F3000 pin 1 2. Check 3V3 on C3108 pin 1 1V8 on C3105 pin 1 1V8 on C3106 pin 1 1V1 on C3104 pin 1 3. Check 26V on Q3100 pin 1 and Q3100 pin 4 4. Check PPDCIN_G3H on Q3100 pin 8 U3200 1. Check 5V on F3001 pin 1 2. Check 3V3 on C3208 pin 1 1V8 on C3205 pin 1 1V8 on C3206 pin 1 1V1 on C3204 pin 1 3. Check 26V on Q3200 pin 1 and Q3200 pin 4 4. Check PPDCIN_G3H on Q3200 pin 8

Power

Boot sequence

* Valid external PSU, bat or charger PBUS PP3V3_G3H_RTC PP3V3_G3H VIN_RTC > VIN_RTC_UPPER_THRESHOLD PP1V8_SLPS2R PMU_CLK32K_SOC PP1V8_AWAKE PP1V8_SLPS2R_PMUGPIO PP1V1_SLPS2R PP0V8_SLPS2R PP0V82_SLPDDR PP3V3_AWAKE PPVDDCPUSRAM_AWAKE PP0V9_SLPDDR PP1V1_SLPDDR_SOCFET_EN PP1V1_SLPDDR H9M_24MHz_CLK PP1V2_AWAKE PPVDDCPU_AWAKE PMU_SYS_ALIVE PMU_ACTIVE_READY PMU_COLD_RESET_L H9M LOAD SECURE ROM, SMC BATTERY TRAP PMU_PVDDMAIN_EN P3V3MAIN_PGOOD PP3V_G3H_RTC PMU_CLK32K_PCH PCH_RTC_RESET_L P5VG3S_EN PP5V_G3S P3V3G3S_EN PP3V3_G3S P1V8G3S_EN PP1V8_G3S P5VG3S_PGOOD PMU_CLK32K_WLANBT SSD 4LANDING: OCARINA I2C WRITE POWER_STATE_TARGET=ACTIVE TO ENABLE SSD POEWR SSD_PMU_RESET_L PPVCCQ_ANI_SSD0 PP0V9_SSD0 SSD0_VR_2V5_EN PP2V5_NAND_SSD0 SSD0_OCARINA_WP_L SSD0_OCARINA_PFN SSD0_PCARINA_RESET_L SSD 2LANDING: CALPE, CONFIGURE RAILS AND GPIOS TO ENABLE SSD POWER PPVCCQ_ANI_SSD0 PP0V9_SSD0 SSD0_PMIC_DISCHARGE_EN SSD0_VR_2V5_EN PP2V5_NAND_SSD0 SSD0_VR_P2V5_PGOOD SSD0_PMIC_RESET_L SSD BEGINS POWER BUTTON MONITORING PMU_ONOFF_L PP3V3_S5 PP1V8_S5 PPVPCORE_S5 PP1V_PRIM SMC_RSMRST_L PM_RSMRST_L SMC WAITS FOR eSPI_RESET# PIN PCH_PWRBTN_L PP1V8_S3 PVDDQ_EN PP1V2_S3 PVDDQ_PGOOD PP1V_S3 PCH DE-ASSERTS SLP_S3#, SLP_A#, SLP_LAN#, and SLP_WLAN# over eSPI PVCCPLLOC_EN PP1V2_S0SW PP1V_S0SW PVCCIO_EN PVCCIO PVCCIO_PGOOD ALL_SYS_PWRGD CPU_VR_READY PM_SYSRST_L PM_PCH_PWROK PM_PCH_SYS_PWROK DONE.

5V to 20V

1. 5V PP20V_USBC_XB_VBUS at F3001 pin 1 2. Check CD3215 LDOs C3208 pin 1 3V3 C3205 pin 1 1V8 (LDOD) C3206 pin 1 1V8 (LDOA) C3204 pin 1 1V1 3. UPC_XB_GATE1 11V UPC_XB_GATE2 7V6 4. 13V PPVIN_G3H_P3V3G3HRTC_R at C6964 pin 1 5. Check R7075 for value of ~4R7 5V CHGR_VDDA at C7075 pin 1 6. 3V3 CHGR_EN_MVR_R at R6968 pin 1 7. 3V3 PP3V3_G3H_RTC_REG_R at L6961 pin 2 8. 3V3 SMC_LID_LEFT at R4807 pin 2 3V3 SMC_LID_RIGHT at R4808 pin 2 3V3 IPD_LID_OPEN ( use TP ) ( A lot of sequence information missing for this area) 9. 20V PP20V_USBC_XB_VBUS at F3001 pin 1 10. UPC_XB_GATE1 26V 11. UPC_XB_GATE2 20V

5V to 20V

1. 5V PP20V_USBC_XB_VBUS at F3001 pin 1 2. Check CD3215 LDOs C3208 pin 1 3V3 C3205 pin 1 1V8 (LDOD) C3206 pin 1 1V8 (LDOA) C3204 pin 1 1V1 3. UPC_XB_GATE1 11V UPC_XB_GATE2 7V6 4. 13V PPVIN_G3H_P3V3G3HRTC_R at C6964 pin 1 5. Check R7075 for value of ~4R7 5V CHGR_VDDA at C7075 pin 1 6. 3V3 CHGR_EN_MVR_R at R6968 pin 1 7. 3V3 PP3V3_G3H_RTC_REG_R at L6961 pin 2 8. 3V3 SMC_LID_LEFT at R4807 pin 2 3V3 SMC_LID_RIGHT at R4808 pin 2 3V3 IPD_LID_OPEN ( use TP ) ( A lot of sequence information missing for this area) 9. 20V PP20V_USBC_XB_VBUS at F3001 pin 1 10. UPC_XB_GATE1 26V 11. UPC_XB_GATE2 20V

CPU

PMU_ONOFF_L PP3V3_S5 PP1V8_S5 PPVCCPRIMCORE_PRIM_REG SMC_RSMRST_L PM_RSMRST_L PM_PWRBTN_L PVDDQ_EN PP2V5_S3 PVDDQ_EN_R ( from P2V5_VPP_PGOOD ) PP1V2_S3 PVDDQ_PGOOD PP1V05_S3 PVCCPLLOC_EN CPU_C10_GATE_L PP1V2_S0SW PP1V05_S0SW PVCCIO_EN PVCCIOS0_EN_FILT_BUF PVCCIO_S0_CPU PVCCIO_PGOOD

Every net with a reading

NetDiodeVoltageResistance
BT_PWR_EN0.462––
BTUARTMUX_OE_L0.485––
BTUARTMUX_SEL_PCH0.4611.800–
CHGR_BGATE0.596––
CHGR_CSI_R_N0.53820.000–
CHGR_CSI_R_P0.53820.000–
CHGR_CSO_R_N0.35413.100–
CHGR_CSO_R_P0.35413.100–
CHGR_EN_MVR0.583––
CHGR_EN_MVR_R0.583––
CHGR_INT_L0.585––
CHGR_LX1–13.100–
CHGR_LX2–13.100–
CHGR_PHASE1–13.100–
CHGR_PHASE2–13.100–
CPUCORE_ISNS1_N–1.500–
CPUCORE_ISNS1_P–1.500–
CPUCORE_ISNS2_N–1.500–
CPUCORE_ISNS2_P–1.500–
CPUCORE_SW1–1.500–
CPUCORE_SW2–1.500–
CPUGT_ISNS1_N–1.500–
CPUGT_ISNS1_P–1.500–
CPUGT_ISNS2_N–1.500–
CPUGT_ISNS2_P–1.500–
CPUGT_ISNS3_N–1.500–
CPUGT_ISNS3_P–1.500–
CPUGT_SW2–1.500–
CPUGT_SW3–1.500–
CPUSA_ISNS_R_N–1.150–
CPUSA_ISNS_R_P–1.150–
CPUVR_SWSA–1.150–
DFR_DISP_VSYNCOL––
DFR_LID_OPEN_LOL––
DFR_TOUCH_CLK32K_RESET_L0.459––
DFR_TOUCH_INT_L0.459––
DFR_TOUCH_RESET_L0.454––
DP_INT_HPD0.715––
DP_XA_HPD0.566––
EDP_BKLT_EN0.498––
EDP_INT_AUX_N0.450––
EDP_INT_AUX_P0.450––
EDP_INT_ML_N<0>0.395––
EDP_INT_ML_N<1>0.395––
EDP_INT_ML_N<2>0.395––
EDP_INT_ML_N<3>0.395––
EDP_INT_ML_P<0>0.395––
EDP_INT_ML_P<1>0.395––
EDP_INT_ML_P<2>0.395––
EDP_INT_ML_P<3>0.395––
EDP_PANEL_PWR_BUF_EN0.723––
GND_P3V3G3HRTC_AGND0.000––
I2C_ALS_SCL0.450––
I2C_ALS_SDA0.450––
I2C_BKLT_SCL0.556––
I2C_BKLT_SDA0.550––
I2C_CAM_ISOL_SCL0.515––
I2C_CAM_ISOL_SDA0.515––
I2C_DFR_SCL_R0.459––
I2C_DFR_SDA_R0.459––
I2C_SPKRAMP_L_SCL0.366––
I2C_SPKRAMP_L_SDA0.365––
I2C_SSD1_SCLOL––
I2C_TBT_X_SCL0.561––
I2C_TBT_X_SDA0.561––
I2C_TBT_XA_INT_L0.663––
I2C_TBT_XB_INT_L0.660––
I2C_TCON_SCL0.619––
I2C_TCON_SDA0.617––
I2C_UPC_X_SCL20.456––
I2C_UPC_X_SDA20.457––
I2C_UPC_XA_DBG_CTL_SCL0.5003.300–
I2C_UPC_XA_DBG_CTL_SDA0.5083.300–
I2S_SPKRAMP_L_BCLK0.366––
I2S_SPKRAMP_L_D2R0.354––
I2S_SPKRAMP_L_D2R_R10.361––
I2S_SPKRAMP_L_D2R_R20.361––
I2S_SPKRAMP_L_LRCLK_R0.365––
I2S_SPKRAMP_L_R2D0.366––
ISNS_CPUDDR_N–1.200–
ISNS_CPUDDR_P–1.200–
ISNS_CPUVCCIO_NEG0.088––
ISNS_CPUVCCIO_POS0.088––
ISNS_HS_COMPUTING_N0.46012.520–
ISNS_HS_COMPUTING_OUT0.710––
ISNS_HS_COMPUTING_P0.46012.520–
ISNS_HS_OTHER3V3_N0.46013.100–
ISNS_HS_OTHER3V3_P0.46013.100–
ISNS_HS_OTHER5V_N0.46013.100–
ISNS_HS_OTHER5V_P0.46013.100–
ISNS_LCDBKLT_N0.460––
ISNS_LCDBKLT_P0.460––
ISNS_P3V3_G3W_SSD0_N0.406––
ISNS_P3V3_G3W_SSD0_P0.406––
ISNS_PPBUS_MAIN_SSD0_N0.408––
ISNS_PPBUS_MAIN_SSD0_P0.408––
ISNS_SSDNAND_N0.46013.100–
ISNS_SSDNAND_P0.46013.100–
ISNS_WLAN_NOL––
ISNS_WLAN_POL––
LCDBKLT_FET_DRV0.468––
LCDBKLT_FET_DRV_R0.475––
LCDBKLT_SW0.425––
MEM_A_TEN_R0.085––
MEMVTT_EN0.507––
MIPI_FTCAM_CLK_CONN_N0.518––
MIPI_FTCAM_CLK_CONN_P0.518––
MIPI_FTCAM_DATA_CONN_N<0>0.518––
MIPI_FTCAM_DATA_CONN_P<0>0.518––
P0V8SLPDDR_SW00.0301.800–
P0V8SLPDDR_SW10.0300.800–
P0V9_LX0_SSD00.2890.900–
P0V9_LX1_SSD00.2890.900–
P0V9SLPDDR_SW00.050––
P0V9SLPDDR_SW10.0500.900–
P1V1SLPS2R_SW00.3001.100–
P1V1SLPS2R_SW10.3001.100–
P1V2_PHASE0.1501.200–
P1V2_WLANBT_VLX0.2891.200–
P1V5_WLANBT_VLX0.3301.500–
P1V8_LX0_SSD00.345––
P1V8SLPS2R_SW00.4101.800–
P1VPRIM_SW00.1501.000–
P1VPRIM_SW1–1.000–
P2V5_SW1_TPS62180_SSD00.355––
P2V5_SW1_TPS62180_SSD1–2.500–
P2V5_SW2_TPS62180_SSD00.355––
P2V5_SW2_TPS62180_SSD1–2.500–
P2V7_SW1_TPS62180_SSD00.3402.700–
P2V7_SW2_TPS62180_SSD00.3402.700–
P3V3G3HRTC_FB1.266––
P3V3G3HRTC_FB_R0.374––
P3V3G3HRTC_PGOOD0.663––
P3V3G3HRTC_PHASE10.3673.300–
P3V3G3HRTC_PHASE20.3673.300–
P3V3G3HRTC_RA_R0.374––
P3V3G3HRTC_SS0.514––
P5VG3S_VSW–5.000–
P5VUSBC_T_LL–5.000–
P5VUSBC_T_NEG–5.000–
P5VUSBC_T_POS–5.000–
P5VUSBC_T_R–5.000–
P5VUSBC_X_BOOT_RC0.576––
P5VUSBC_X_DRVH0.902––
P5VUSBC_X_DRVH_R0.902––
P5VUSBC_X_DRVL0.444––
P5VUSBC_X_FSEL0.522––
P5VUSBC_X_LL0.4655.000–
P5VUSBC_X_NEG0.465––
P5VUSBC_X_OCSET0.518––
P5VUSBC_X_PGOOD0.518––
P5VUSBC_X_POS0.465––
P5VUSBC_X_R0.4655.000–
P5VUSBC_X_RTN_DIV0.516––
P5VUSBC_X_SENSE_DIV0.513––
P5VUSBC_X_SET00.522––
P5VUSBC_X_SET10.522––
P5VUSBC_X_SREF0.519––
P5VUSBC_X_VBST0.575––
P5VUSBC_X_VO0.517––
P5VUSBCT_LL0.193––
P5VUSBCT_R0.193––
PANEL_P3V3_EN0.547––
PBUS_S0_VSENSE_IN0.46013.100–
PCH_UART_BT_CTS_L0.693––
PCH_UART_BT_D2R0.7041.800–
PCH_UART_BT_R2D0.7031.800–
PCH_UART_BT_RTS_L0.695––
PHV_INT_XA_G3H0.615––
PM_RSMRST_L0.475––
PP0V9_SLPDDR0.0500.900–
PP0V9_SSD00.2890.900–
PP0V9_TBT_T_SVR0.9000.900–
PP0V9_TBT_X_SVR0.2550.900–
PP0V82_SLPDDR0.0301.800–
PP0V95_S0_CPUVCCIO_REG_R0.0440.950–
PP1V_PRIM0.1501.000–
PP1V1_SLPDDR0.363––
PP1V1_SLPS2R0.3001.100–
PP1V1_UPC_XA_LDO_BMC0.4851.100–
PP1V1_UPC_XB_LDO_BMC0.4851.100–
PP1V2_S30.1501.200–
PP1V2_S3_REG_R0.1501.200–
PP1V2_WLANBT0.290––
PP1V2_WLANBT_C0.2891.200–
PP1V5_WLANBT0.330––
PP1V5_WLANBT_C0.3301.500–
PP1V8_G3S0.315––
PP1V8_G3S_WLANBT_VDDIO0.336––
PP1V8_S30.4201.800–
PP1V8_S3_MEM0.4201.800–
PP1V8_SLPS2R0.4101.800–
PP1V8_SLPS2RSW_DFR0.528––
PP1V8_SSD00.346––
PP1V8_UPC_XA_LDOA0.5051.800–
PP1V8_UPC_XA_LDOD0.4701.800–
PP1V8_UPC_XB_LDOA0.5071.800–
PP1V8_UPC_XB_LDOD0.473––
PP2V5_NAND_SSD00.356––
PP2V5_NAND_SSD1–2.500–
PP2V7_NAND_SSD00.3402.700–
PP3V0_G3H_RTC0.480––
PP3V3_G3H_RTC–3.300–
PP3V3_G3H_RTC_ISOL–3.300–
PP3V3_G3H_RTC_REG_R0.3673.300–
PP3V3_G3H_RTC_X0.3973.300–
PP3V3_G3H_SOCPMU–3.300–
PP3V3_G3H_SSD0_SNS–3.300–
PP3V3_G3H_T–3.300–
PP3V3_G3S0.3003.300–
PP3V3_G3S_TPAD0.3003.300–
PP3V3_G3S_WLAN0.3543.300–
PP3V3_G3S_X0.354––
PP3V3_G3SSW_SNS0.4933.300–
PP3V3_S0SW_LCD0.553––
PP3V3_S0SW_TBT_X_SNS0.500––
PP3V3_S50.3303.300–
PP3V3_TBT_T_F0.5203.300–
PP3V3_TBT_T_S00.5203.300–
PP3V3_TBT_X_ANA0.516––
PP3V3_TBT_X_ANA_PCIE0.498––
PP3V3_TBT_X_F0.502––
PP3V3_TBT_X_LC0.560––
PP3V3_TBT_X_SX0.525––
PP3V3_UPC_TA_LDO–3.300–
PP3V3_UPC_TB_LDO–3.300–
PP3V3_UPC_XA_LDO0.4903.300–
PP3V3_UPC_XB_LDO0.4963.300–
PP5V_G3S0.3905.000–
PP5V_G3S_DFR_FILT0.3905.000–
PP5V_G3S_VCCIOVCC0.390––
PP5V_S0_ALSCAM_F0.404––
PP5V_S0SW_LCD0.573––
PP5V_S4_T_USBC0.5055.000–
PP5V_S4_X_USBC0.4655.000–
PP5V_USBC_X_VCC0.390––
PP20V_USBC_TA_VBUS0.17020.000–
PP20V_USBC_TA_VBUS_F0.17020.000–
PP20V_USBC_TB_VBUS0.17020.000–
PP20V_USBC_TB_VBUS_F0.17020.000–
PP20V_USBC_XA_VBUS0.17020.000–
PP20V_USBC_XA_VBUS_F0.17020.000–
PP20V_USBC_XB_VBUS0.17020.000–
PP20V_USBC_XB_VBUS_F0.17020.000–
PPBUS_G3H0.35412.520–
PPBUS_G3H_SPKRAMP_RIGHT0.46013.100–
PPBUS_G3H_SSD00.46013.100–
PPBUS_G3H_SSD0_SNS0.409––
PPBUS_G3H_SSD1_SNS0.42512.600–
PPBUS_HS_3V3G3H_T–12.600–
PPBUS_HS_CPU0.35512.520–
PPDCIN_G3H0.53820.000–
PPDCIN_G3H_CHGR–5.000–
PPVBAT_G3H_CHGR_R0.35413.100–
PPVBAT_G3H_CHGR_REG0.35413.100–
PPVBAT_G3H_CONN0.880––
PPVCC_CPU_PH1–1.500–
PPVCC_S0_CPU–1.500–
PPVCCEDRAM_S0_CPU0.0501.000–
PPVCCEDRAM_S0_REG_R0.0501.000–
PPVCCGT_CPU_PH1–1.500–
PPVCCGT_CPU_PH2–1.500–
PPVCCGT_CPU_PH3–1.500–
PPVCCGT_S0_CPU–1.500–
PPVCCIO_S0_CPU0.0440.950–
PPVCCPRIMCORE_PRIM_REG0.115––
PPVCCSA_CPU_R–1.150–
PPVCCSA_S0_CPU–1.150–
PPVDDCPU_AWAKE0.0100.625–
PPVDDCPUSRAM_AWAKE0.4900.800–
PPVIN_G3H_P3V3G3H0.46013.100–
PPVIN_G3H_P3V3G3HRTC–13.100–
PPVIN_G3H_P3V3G3HRTC_R0.40512.000–
PPVIN_G3H_P5VG3S0.46013.100–
PPVIN_RFLDO_WLANBT0.323––
PPVIN_RFLDO_WLANBT_C0.3231.800–
PPVIN_S0SW_LCDBKLT0.85012.900–
PPVIN_S0SW_LCDBKLT_F0.460––
PPVIN_S0SW_LCDBKLT_R0.460––
PPVIN_S4_TPAD_FUSE–13.100–
PPVIN_SW_LCDBKLT_SW0.85012.900–
PPVOUT_S0_LCDBKLT1.15355.000–
PPVPCORE_S50.255––
PVCCEDRAM_PHASE0.0501.000–
PVCCEDRAM_REFIN0.632––
PVCCEDRAMS0_CS_N0.0501.000–
PVCCEDRAMS0_CS_P0.0501.000–
PVCCIO_DRVH0.522––
PVCCIO_DRVH_R0.522––
PVCCIO_DRVL0.458––
PVCCIO_DRVL_R0.437––
PVCCIO_LL0.044––
PVCCIO_PGOOD0.533––
PVCCIO_PHASE0.0440.950–
PVCCIO_VBST0.633––
PVCCIOS0_AGND0.000––
PVCCIOS0_CS_N0.0440.950–
PVCCIOS0_CS_P0.0440.950–
PVCCIOS0_EN_FILT0.526––
PVCCIOS0_EN_FILT_BUF0.516––
PVCCIOS0_EN_R0.574––
PVCCIOS0_FB0.532––
PVCCIOS0_FSEL0.523––
PVCCIOS0_RTN0.539––
PVCCIOS0_SREF0.540––
PVCCIOS0_VO0.532––
PVCCOIOS0_OCSET0.532––
PVCCPCOREPRIM_SW0–1.000–
PVCCPCOREPRIM_SW10.2551.000–
PVCCPLLOC_EN0.492––
PVCCPRIMCORE_SW00.115––
PVCCPRIMCORE_SW10.118––
PVDDCPUAWAKE_SW00.0100.625–
PVDDCPUAWAKE_SW10.0100.625–
PVDDCPUAWAKE_SW20.0100.625–
PVDDCPUAWAKE_SW30.0100.625–
PVDDCPUSRAMAWAKE_SW00.4900.800–
PVDDQ_EN0.711––
PVIN_RFLDO_WLANBT_VLX0.3231.800–
SAVE_BAT_G0.757––
SAVE_BAT_S1.060––
SOC_DOCK_CONNECT0.446––
SPI_DFR_CLK0.465––
SPI_DFR_CS_L0.451––
SPI_DFR_MISO_R0.464––
SPI_DFR_MOSI0.465––
SPKRAMP_INT_L0.349––
SPKRAMP_LT_AREG0.563––
SPKRAMP_LT_BSTN0.755––
SPKRAMP_LT_BSTP0.754––
SPKRAMP_LT_DREG0.500––
SPKRAMP_LT_MODE0.000––
SPKRAMP_LT_OUTN0.450––
SPKRAMP_LT_OUTP0.454––
SPKRAMP_LW_AREG0.562––
SPKRAMP_LW_BSTN0.754––
SPKRAMP_LW_BSTP0.754––
SPKRAMP_LW_DREG0.500––
SPKRAMP_LW_MODE0.337––
SPKRAMP_LW_OUTN0.458––
SPKRAMP_LW_OUTP0.458––
SPKRAMP_RESET_L0.348––
SPKRCONN_LT_OUTN0.450––
SPKRCONN_LT_OUTP0.464––
SPKRCONN_LW_OUTN0.458––
SPKRCONN_LW_OUTP0.458––
SSD0_CLKREQ2_L0.442––
SSD0_S4E2_PCIE_RESREF0.723––
SSD0_S4E2_ZQ_L0.240––
SSD0_SWDIO_UART_D2R0.416––
SSD1_CLKREQ2_L0.475––
SSD1_PCIE_RESET_L0.469––
SSD1_S4E2_ZQ_COL––
SWD_SOC_SWCLK0.448––
SWD_SOC_SWDIO0.448––
TBT_POC_RESET0.698––
TBT_WAKE_3V3_L0.541––
TBT_X_CIO_PWR_EN0.541––
TBT_X_PCI_RESET_L0.545––
TBT_X_PLUG_EVENT_L0.553––
TBT_X_ROM_HOLD_L0.660––
TBT_X_ROM_WP_L0.564––
TBT_X_SPI_CLK0.540––
TBT_X_SPI_CLK_DBG0.581––
TBT_X_SPI_CS_L0.565––
TBT_X_SPI_MISO0.566––
TBT_X_SPI_MOSI0.569––
TBT_X_USB_PWR_EN0.541––
TBT_XA_LSRX0.754––
TBT_XA_LSTX0.786––
TP_DFR_TOUCH_PANEL_DETECTOL––
TP_DFR_TOUCH_ROM_WCOL––
TP_DFR_TOUCH_RSVDOL––
TP_Q3100_DRAIN0.580––
TP_UPC_XA_SWD_CLK0.719––
TP_UPC_XA_SWD_DATA0.719––
TP_USBC_XA_RESET_L0.747––
TP_WLAN_PMU_TEST0.754––
TSNS_T1_DX5_P0.659––
UART_BT_D2R0.4771.800–
UART_BT_D2R_CTS_L0.4791.800–
UART_BT_MUX_CTS_L0.624––
UART_BT_MUX_RTS_L0.626––
UART_BT_R2D0.476––
UART_BT_R2D_RTS_L0.475––
UART_WLAN_D2R0.481––
UART_WLAN_D2R_CTS_L0.480––
UPC_I2C_INT_L0.447––
UPC_X_5V_EN0.668––
UPC_X_5V_EN_R0.522––
UPC_XA_DBG10.543––
UPC_XA_DBG20.543––
UPC_XA_FAULT_L0.719––
UPC_XA_GATE10.635––
UPC_XA_GATE20.626––
UPC_XA_GPIO0OL––
UPC_XA_R_OSC0.508––
UPC_XA_SS0.504––
UPC_XA_UART_RX0.706––
UPC_XA_UART_TX0.7083.300–
USB_DBG_PCH_XA_F_N0.411––
USB_DBG_PCH_XA_F_P0.411––
USB_SOC_N0.682–645.000k
USB_SOC_P0.682–645.000k
USB_SOC_TYPEC_N0.682––
USB_SOC_TYPEC_P0.682––
USB_UPC_XA_N0.722––
USB_UPC_XA_P0.722––
USB3_EXTA_R2D_N0.696––
USB3_EXTA_R2D_P0.696––
USBC_X_RESET_L0.736––
USBC_XA_CC10.570––
USBC_XA_CC1_CONN0.750––
USBC_XA_CC20.576––
USBC_XA_CC2_CONN0.727––
USBC_XA_SBU1OL––
USBC_XA_SBU2OL––
USBC_XA_USB_DBG_BOT_N0.337––
USBC_XA_USB_DBG_BOT_P0.338––
USBC_XA_USB_DBG_TOP_N0.340––
USBC_XA_USB_DBG_TOP_P0.340––
USBC_XA_USB_TOP_N0.538––
USBC_XA_USB_TOP_P0.544––
VR0V9_IND_TBT_T0.9000.900–
VR0V9_IND_TBT_X0.2550.900–
WL_GPIO_130.659––
WLAN_AUDIO_SYNC0.336––
WLAN_CONTEXT_A0.467––
WLAN_CONTEXT_B0.471––
WLAN_JTAG_SEL0.744––
WLAN_JTAG_TCK0.471––
WLAN_PWR_EN0.463––
WLAN_SROM_STRAP0.746––
XDP_CPU_TRST_L0.262––
XDP_DBRESET_L0.785––
XDP_PCH_JTAGX0.045––
XDP_PCH_TDI0.210––
XDP_PCH_TMS0.210––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01041?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01041: diode 0.354, voltage 12.520. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01041?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01041: diode 0.330, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H_RTC read on the 820-01041?

OpenBoardData's known-good values for PP3V3_G3H_RTC on the 820-01041: voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01041 board?

Open your own 820-01041 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License