Apple laptop board · OpenBoardData

820-00840 known-good readings

Known-good readings for the Apple laptop board 820-00840: 1,288 nets, including 84 power rails sorted by startup stage, with repair notes, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 84 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-00840.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 84 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 20

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V3_G3H0.363.300–
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is the always-on 3.3 V rail from the G3H group (from its name), and the power sequence places it after PM_EN_P3V3_G3H from U7000 to U6990 pin 10, feeding U5000 as PP3V3_S5_SMC, U3100 at C3100 pin 1, and U1900 pins 1 and 11. Community readings here are diode 0.36 and voltage 3.300; treat these as a guide only. With the board unpowered, measure diode mode from the rail to ground, then power up and measure the voltage. A voltage well below 3.3 V points to the enable or upstream supply; a diode reading far from 0.36 suggests a short or open on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_G3H_UPC_XA0.353.300–
AI: what PP3V3_G3H_UPC_XA is and how to check it

PP3V3_G3H_UPC_XA is a 3.3 V always-on rail feeding the USB-C (UPC) side of the CD3215 area; the G3H part of the name means always-on, and UPC_XA is from the name. Known-good readings from the archive: diode 0.35 and voltage 3.300. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage well off 3.3 V or a diode reading far from 0.35 usually points to a short or a missing enable upstream, not proof of a bad part on its own. No known-good resistance reading is recorded for this rail.

PP3V3_G3H_UPC_XB0.363.300–
AI: what PP3V3_G3H_UPC_XB is and how to check it

PP3V3_G3H_UPC_XB is a 3.3 V always-on rail, from the name: G3H means always on, and UPC_XB points to the USB-C side B circuitry. Known-good readings here are diode 0.36 and voltage 3.300; these are community figures and a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.36 suggests a short or leaky part on the rail; no known-good resistance reading exists here, so compare against the matching UPC_XA rail or a known-good board.

PP3V3_G3H_VR0.353.300–
AI: what PP3V3_G3H_VR is and how to check it

PP3V3_G3H_VR is the always-on 3.3 V rail in the G3H startup stage, judged from its name; it feeds the early logic that must be up before the board can sequence on. Known-good readings in the archive are diode 0.35 and voltage 3.300, with no condition noted, so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far below 3.3 V points to the rail not being enabled or being loaded down, while a diode reading well under 0.35 suggests a short on the rail; no known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PPBUS_G3H0.45013.100–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the "G3H" suffix means it's always-on, from the name. Known-good readings in the archive: diode 0.450 and voltage 13.100 (no condition recorded). Check it with the board unpowered and battery disconnected in diode mode from PPBUS_G3H to ground, then power up and measure the voltage. A diode reading well below 0.450 suggests a short or leaky load on the rail; a voltage far from 13.1 V points to the charger side not regulating, but no known-good resistance reading exists here, so compare against a matching rail or a known-good board before condemning a part.

PPBUS_G3H_CPU0.46013.100–
AI: what PPBUS_G3H_CPU is and how to check it

PPBUS_G3H_CPU is the main bus rail feeding the CPU section; the G3H part of the name means "always on", so it should be present whenever the board has power. The archive lists a known-good diode reading of 0.460 and a voltage of 13.100, with no condition noted, so treat these as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.460 usually points to a short or a leaky part on the rail; a voltage well off 13.100 suggests the bus isn't being generated or is loaded down. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PPBUS_G3H_P3V3S50.45013.100–
AI: what PPBUS_G3H_P3V3S5 is and how to check it

PPBUS_G3H_P3V3S5 is a main power rail; the "G3H" part of the name indicates it is always-on, and the "P3V3S5" part suggests it also feeds the 3.3V S5 domain (this is from the name, not the board data).

  • Known-good readings from the archive: diode 0.450, voltage 13.100. These are community values and only a guide.
  • To check: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage.
  • A diode reading far below 0.450 suggests a short or a leaky load on the rail; a voltage well off 13.1V points to the supply feeding it or a heavy load pulling it down.
  • No known-good resistance reading exists here, so compare against a matching rail or a known-good board.
PPBUS_G3H_P5VS40.4513.100–
AI: what PPBUS_G3H_P5VS4 is and how to check it

PPBUS_G3H_P5VS4 is the main system bus rail that feeds the P5VS4 (5V S4) stage; the "G3H" part of the name indicates it is always-on, and the "P5VS4" part ties it to the S4 turn-on phase. From the readings archive, the known-good guide values are a diode reading of 0.45 and a voltage of 13.100. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.45 suggests a short or leaky load on the rail, while a missing or low voltage points to the upstream supply or enable not coming up; there is no known-good resistance reading for this rail here.

PPBUS_G3H_R0.37––
AI: what PPBUS_G3H_R is and how to check it
  • What it is: PPBUS_G3H_R is the main battery/charger bus rail; the "G3H" part of the name indicates it is always-on (from the name), and "_R" typically marks a secondary or related branch of that bus (general naming, not from this board's data).
  • Known-good reading: the archive lists a diode reading of 0.37 for PPBUS_G3H_R. No known-good voltage or resistance reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from PPBUS_G3H_R to ground and compare with 0.37; then apply power and measure the rail's voltage. The archive has no expected voltage for this rail, so compare against a known-good board or the matching bus net.
  • If far off: a much lower diode reading usually points to a short or a leaky component on the rail; a much higher one can mean an open path. Confirm with a second measurement before replacing anything.
PPBUS_G3H_SPKRL0.45013.100–
AI: what PPBUS_G3H_SPKRL is and how to check it

PPBUS_G3H_SPKRL is a main power-bus rail; the G3H part of the name means always-on, and the SPKRL suffix suggests a speaker-related branch (that part is from the name, not confirmed by data). Known-good readings here are diode 0.450 and 13.100 V, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.450 suggests a short or leaky load on the rail; a voltage well off 13.100 V points to the bus supply or its enable, but that's a likely cause, not confirmed. No known-good resistance reading exists for this rail.

PPBUS_G3H_SSD0.46––
AI: what PPBUS_G3H_SSD is and how to check it

PPBUS_G3H_SSD is the main bus rail feeding the SSD section; the G3H part of the name means it is always-on whenever the board has power. The only known-good figure here is a diode reading of 0.46 to ground, with no condition noted; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage on the rail. A diode reading far below 0.46 usually points to a short or a leaky part on that rail, while a much higher one can mean an open connection; treat these as guides, not proof of a bad part.

PPBUS_G3H_TPAD0.45013.100–
AI: what PPBUS_G3H_TPAD is and how to check it

PPBUS_G3H_TPAD is a G3H (always-on) rail, judging from its name, and the "TPAD" suffix suggests it feeds the trackpad side of the board. Known-good readings here are diode 0.450 and 13.100 V, with no condition recorded, so treat them as a guide from community contributions. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading well below 0.450 suggests a short or leaky load on the rail; a voltage far from 13.100 V points to the source or its enable, not the trackpad. No known-good resistance reading exists for this rail.

PPDCIN_G3H0.5620.000–
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the main DC input rail in the always-on G3H state, judging from its name; the power sequence lists it at 5V early on and at 20V at Q3100 pin 8 once USB-C negotiation completes. Known-good readings here are diode 0.56 and voltage 20.000, with no condition recorded. With the board unpowered, measure diode mode from PPDCIN_G3H to ground and compare with 0.56; then apply power and check the voltage, expecting about 20V once the 20V path is up. A diode reading far below 0.56 suggests a short or leaky load on the rail, while a missing 20V with a good diode reading points upstream to the USB-C input and negotiation stages rather than the rail itself. These are community readings and a guide only, not a confirmed diagnosis.

PPDCIN_G3H_CHGR0.5620.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side input rail of the G3H (always-on) domain, judged from its name; it is the main DC input the charger section works from. In the readings archive it shows a diode reading of 0.56 and a voltage of 20.000, which are community values and only a guide. Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure the voltage on the rail. A voltage far below 20 V points to the input path or charger section not passing power, while a diode reading far from 0.56 can suggest a short or a damaged component on the rail; there is no known-good resistance reading here, so compare against a matching rail or a known-good board.

PPDCIN_G3H_CHGR_R0.56––
AI: what PPDCIN_G3H_CHGR_R is and how to check it

PPDCIN_G3H_CHGR_R — the name indicates the charger-side DC input rail in the G3H (always-on) domain, i.e. the main adapter input feeding the charger circuit. It appears in the power sequence as PPDCIN_G3H, expected at 5V early and 20V once the CD3215 negotiates.

  • Known-good: diode-to-ground 0.56 (community reading, a guide only; board state affects it). No known-good voltage reading is listed here.
  • Check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail. Then apply power and measure the voltage.
  • A diode reading far below 0.56 usually suggests a short or leaky part on the rail; far above suggests an open path. Confirm with a second measurement before suspecting a part.
PPDCIN_G3H_VSNS_IN0.56––
AI: what PPDCIN_G3H_VSNS_IN is and how to check it

PPDCIN_G3H_VSNS_IN is a sense input on the PPDCIN_G3H rail; the G3H part of the name indicates an always-on startup rail, and VSNS_IN indicates a sense line.

  • Known-good: diode 0.56 (community reading, guide only; no condition recorded). No known-good voltage or resistance reading here.
  • Check: power off and unplug, then diode mode from PPDCIN_G3H_VSNS_IN to ground. Then apply power and measure the voltage on it, comparing with PPDCIN_G3H itself, which the sequence expects at 5V early and 20V later.
  • A diode reading far below 0.56 usually points to a short or leaky component on that net; far above it suggests an open trace or missing connection. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CHGR_R0.45013.100–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is a charger-side battery rail; the "G3H" in its name marks it as an always-on rail, and "CHGR" points to the charging circuit. The archive's known-good guide is a diode reading of 0.450 to ground and 13.100 V with power applied; no known-good resistance reading is recorded here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.450, then power up and check the voltage against 13.100 V. A diode value far below known-good usually suggests a short or leaky part on the rail, while a missing or low voltage points to the charger not delivering it; treat these as likely causes, not confirmed ones.

PPVBAT_G3H_CHGR_REG0.45013.100–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a charger-side battery rail; the "G3H" part of the name indicates it is always-on, and "CHGR_REG" points to the charger circuit. The archive lists a known-good diode reading of 0.450 and a voltage of 13.100; treat these as a guide, since community readings vary with board state. Check it with the board unpowered and the battery disconnected: diode mode, red probe to ground, black probe on the rail, and compare with 0.450. Then apply power and measure the voltage, expecting about 13.1 V. A diode reading far below known-good usually suggests a short or leaky part on the rail; a missing or low voltage points to the charger not regulating or an open path feeding it. No known-good resistance reading is recorded for this rail.

PPVBAT_G3H_CONN0.6313.100–
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is a battery/always-on rail; the G3H part of the name indicates it stays present in the always-on state, and CONN suggests it runs to the battery connector. Known-good from the archive: diode 0.63 in diode mode and 13.100 V with power applied (community readings, a guide only). Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode reading far below 0.63 suggests a short or leaky part on the rail; a voltage well off 13.100 V points to a supply or charging-path problem rather than the rail itself. No known-good resistance reading is recorded here.

PPVIN_G3H_P3V3G3H0.55––
AI: what PPVIN_G3H_P3V3G3H is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V3G3H is the input supply for the always-on 3V3 G3H rail (G3H = always on). It feeds PP3V3_G3H, which the power sequence shows going to U5000, U3100 and U1900.
  • Known-good reading: diode 0.55 to ground (community value, a guide only; board state varies). No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the DC voltage on it.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a high or open reading suggests a broken feed. Confirm with voltage under power before replacing anything.

S5 and SUS: standby 21

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V_S5_PCH_DCPDSW0.34––
AI: what PP1V_S5_PCH_DCPDSW is and how to check it
  • What it is: From the name, a 1V rail in the S5 (standby) domain feeding the PCH's DCPD switch. The board data gives no further detail on its function.
  • Known-good: diode reading 0.34 to ground (community figure, a guide only). No known-good voltage is listed here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a low diode reading or missing voltage usually points to a short or a rail that isn't being enabled, but one reading doesn't confirm a bad part. Compare against a matching rail on the other side of the pair before replacing anything.
PP1V_S5G0.1001.000–
AI: what PP1V_S5G is and how to check it

PP1V_S5G — the name indicates a 1 V rail in the S5 (standby) domain, so it should be present in standby before the board fully turns on. The archive lists a known-good diode reading of 0.100 and a voltage of 1.000 V; treat these as a guide, since community readings vary with board state. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. In the published sequence it is generated at step 32 and fed to U0500 VCCPRIM_1P0, so it depends on the earlier standby steps being in place. A diode reading far from 0.100 usually points to a short or leak on the rail; a missing or low voltage with a normal diode reading points upstream to its regulator and enables. No known-good resistance reading is available here.

PP1V_S5G_PCHCLK0.11––
AI: what PP1V_S5G_PCHCLK is and how to check it
  • What it is: From the name, PP1V_S5G_PCHCLK is a 1 V rail in the S5 (standby) group that clocks the PCH. The power sequence lists PP1V_S5G as generated at step 32 and fed to U0500 VCCPRIM_1P0, but it doesn't name PP1V_S5G_PCHCLK itself.
  • Known-good: diode 0.11 (community reading, a guide only). No known-good voltage reading here.
  • How to check: power off, then diode mode from the rail to ground; then power on and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a second measurement before replacing anything.
PP1V_S5G_REG0.0441.00045.00R
AI: what PP1V_S5G_REG is and how to check it

PP1V_S5G_REG is a 1 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, and the sequence shows PP1V_S5G being generated and fed to U0500 VCCPRIM_1P0. The archive lists diode 0.044, voltage 1.000 V and resistance 45.00R, with no stated condition, so treat them as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from these usually points to a short or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part; no known-good value of another kind is listed here.

PP1V_S5GTD0.1101.000–
AI: what PP1V_S5GTD is and how to check it

PP1V_S5GTD is a 1 V standby rail; the "S5" and "SUS" in the name point to the suspend/standby stage of the power sequence, and "TD" is not explained in the available data. Known-good readings here are diode 0.110 and voltage 1.000, with no condition recorded, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; a far-off diode reading usually suggests a short or a damaged component on that rail, while a correct diode reading with missing voltage points back to its enable or source. No known-good resistance reading exists for this rail.

PP1V_SUS_PCH_VCCCLK2_F0.1001.000–
AI: what PP1V_SUS_PCH_VCCCLK2_F is and how to check it

PP1V_SUS_PCH_VCCCLK2_F is a 1V standby rail feeding the PCH clock section; the "SUS" in the name points to the suspend/standby domain, and this is inferred from the name only. Known-good readings in the archive: diode 0.100 and voltage 1.000. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far below 0.100 suggests a short or leaky load on the rail; a missing or low voltage with a normal diode reading points upstream at the rail's enable or source. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.

PP1V_SUS_PCH_VCCCLK4_F0.1001.000–
AI: what PP1V_SUS_PCH_VCCCLK4_F is and how to check it

PP1V_SUS_PCH_VCCCLK4_F is a 1V standby rail feeding the PCH clock section, judging from its name (SUS = suspend/standby). The archive lists a known-good diode reading of 0.100 to ground and 1.000 V with power applied; treat these as a guide, since community readings vary with board state.

  • Check it unpowered in diode mode from the rail to ground; a value far below 0.100 suggests a short or a leaky part on the rail.
  • Then power the board and measure the voltage; it should sit near 1.000 V once the standby rail is up.
  • No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board if you need one.
  • A voltage well off 1.000 V with a normal diode reading points more toward the rail's supply or enable than a short.
PP1V_SUS_PCH_VCCCLK5_F0.1001.000–
AI: what PP1V_SUS_PCH_VCCCLK5_F is and how to check it

PP1V_SUS_PCH_VCCCLK5_F — reference note

  • From the name, this is a 1 V standby (SUS/S5) rail feeding the PCH clock section (VCCCLK5). The "F" suffix is not explained by the name alone.
  • Known-good from the readings archive: diode 0.100 to ground, voltage 1.000 V. These are community guide values and vary with board state.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.100 suggests a short or a leaky load on the rail; a voltage well off 1.000 V points to the rail not being enabled or being pulled down. No known-good resistance reading here, so compare against a matching rail or a known-good board.
  • It sits in the standby stage, so it should be present before the board is turned on.
PP1V_SUSRS0SW_PCHCLK0.04–46.69R
AI: what PP1V_SUSRS0SW_PCHCLK is and how to check it

PP1V_SUSRS0SW_PCHCLK is a 1 V standby rail for the PCH clock, judging by its name (PP1V = 1 V, SUS = suspend/standby, PCHCLK = PCH clock). It belongs to the S5/SUS standby startup stage.

  • Known-good from the archive: diode 0.04 and resistance 46.69R to ground, board unpowered. No known-good voltage reading here.
  • Check it with the board off in diode mode to ground, then power up and measure the voltage; compare the diode reading with the archive value.
  • A diode or resistance far below 46.69R suggests a short or leaky part on the rail; a far higher reading suggests an open trace or missing feed. One reading alone doesn't prove a part bad.
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.1101.000–
AI: what PP1V_SUSSW_PCH_VCCAMPHYPLL_F is and how to check it

PP1V_SUSSW_PCH_VCCAMPHYPLL_F is a 1V standby rail feeding the PCH's VCCAMPHYPLL domain; the S5/SUS part of the name places it in the standby stage, before the main power-on sequence. Known-good readings here are diode 0.110 and voltage 1.000, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.110 usually points to a short or a leaky load on the rail; a voltage far from 1.000 with a normal diode reading points upstream at the regulator or its enable. These are community readings and only a guide, and no known-good resistance value is recorded for this rail.

PP1V2_S5_SMC_VDDC0.52––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC is a 1.2 V rail in the S5 standby domain, judging by its name (S5/SUS = standby), feeding the SMC's VDDC supply. The only known-good reading here is a diode value of 0.52 to ground; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.52.
  • Then apply power and check the voltage is present at 1.2 V.

A diode reading far from 0.52 usually points to a short or a damaged part on the rail, but a small difference can be normal, so confirm with the voltage measurement before replacing anything.

PP1V8_S5G0.3321.800–
AI: what PP1V8_S5G is and how to check it

PP1V8_S5G is a 1.8 V standby rail; the S5 and SUS in the name indicate standby, so it should be present before the board fully turns on. In the sequence it comes from L7930 pin 2 and also enables U8205, which then makes PP3V3_S5G.

  • Known-good readings: diode 0.332 to ground, and 1.800 V with power applied. These are community figures and a guide only.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail (or L7930 pin 2). Then power up and measure the voltage.
  • A diode reading far from 0.332 usually points to a short or a leaky part on the rail; a missing or low voltage points back to the enable path (PM_SLP_SUS_L at R1458 pin 1) or to L7930 and its supply.
  • No known-good resistance reading is recorded for this rail.
PP1V8_SUS_PCH_VCC1P8OL––
AI: what PP1V8_SUS_PCH_VCC1P8 is and how to check it

PP1V8_SUS_PCH_VCC1P8 is a 1.8 V standby rail feeding the PCH, judging by its name (PP1V8 = 1.8 V, SUS = suspend/standby). The only archived reading is diode mode to ground: OL (open, no conduction to ground). That is a community guide, not a confirmed spec.

  • Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage; it should sit near 1.8 V when standby is present.
  • No known-good voltage reading exists here for this rail, so compare against a matching 1.8 V rail or a known-good board.
  • A diode reading far below OL suggests a short or leaky load on the rail; OL alone doesn't prove the rail is good, so confirm with the voltage measurement.
PP3V0_S5_AVREF_SMC0.60––
AI: what PP3V0_S5_AVREF_SMC is and how to check it
  • What it is: From the name, a 3.0 V S5 standby rail feeding the SMC's analog reference (AVREF). The S5/SUS stage means it belongs to standby, before the board fully turns on.
  • Known-good reading: diode 0.60 to ground. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail. Compare the voltage against a matching net or a known-good board, since no value is listed.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open path. Confirm with a second measurement before replacing anything.
PP3V3_S50.3803.300–
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is the 3.3 V standby rail; the S5 suffix comes from its name and places it in the S5/SUS standby stage of the power sequence. Known-good readings here are diode 0.380 and 3.300 V, community-contributed so treat them as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far off 3.300 V usually points to the rail not being enabled or its source not running; a diode reading far from 0.380 suggests a short or a damaged load, but one reading alone doesn't confirm a bad part. No known-good resistance value is listed for this rail.

PP3V3_S5_S0R0.390––
AI: what PP3V3_S5_S0R is and how to check it

PP3V3_S5_S0R is a 3.3 V rail; the S5/SUS part of the name places it in the standby stage, and the S0R suffix suggests it stays up into run power (from the name only). The only known-good figure here is a diode reading of 0.390 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far below 0.390 suggests a short or a leaky part on the rail; a value far above it can mean an open trace or missing part. Treat the 0.390 as a community guide, not a guaranteed value.

PP3V3_S5_SSD_SNS0.3803.300–
AI: what PP3V3_S5_SSD_SNS is and how to check it

PP3V3_S5_SSD_SNS — the name indicates a 3.3 V sense line on the S5 standby rail (S5/SUS = standby, from the name). It is not in the power sequence notes, so its exact role isn't documented here.

  • Known-good (community archive, guide only): diode 0.380 to ground, voltage 3.300 V.
  • Check with the board unpowered: diode mode, red probe on ground, black on the net.
  • Then power up and measure the voltage on the net.
  • A diode reading far below 0.380 suggests a short or leaky part on the rail; a missing 3.3 V with a normal diode reading points upstream to the S5 source. No known-good resistance reading here.
PP3V3_S5_TBT_X_SW0.46––
AI: what PP3V3_S5_TBT_X_SW is and how to check it

PP3V3_S5_TBT_X_SW is a 3.3 V standby rail for the Thunderbolt (TBT) side, judging from its name; the S5 part places it in the standby stage of the power sequence. The only known-good reading here is a diode value of 0.46 to ground (no condition recorded), and there is no known-good voltage reading for this rail. With the board unpowered, measure diode mode from the rail to ground and compare with 0.46; then power up and check the voltage, which should sit near 3.3 V once standby is up. A diode reading far below 0.46 usually points to a short or a leaky part on the rail, while a missing voltage with a normal diode reading points more to the rail's enable or supply upstream. These are guides from community readings, not confirmed values.

PP3V3_S5G0.343.300–
AI: what PP3V3_S5G is and how to check it

PP3V3_S5G is a 3.3 V standby rail; the S5 and SUS naming indicates standby, and in the power sequence it appears at step 28, coming out of U8205 pin 13 after PP1V8_S5G is present. Known-good readings in the archive are diode 0.34 and 3.300 V, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.34 suggests a short or leaky load on the rail; a missing 3.3 V points back to U8205 and its enable, PP1V8_S5G. These are community readings, so treat them as a guide, and there is no known-good resistance value here.

PP5V_S50.435.000–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5V standby rail (S5/SUS = standby, from the name). It comes up at step 22 of the power sequence, after PM_EN_P5VS5 and PM_EN_PVXS5 from U7890 pin 4. Known-good readings here: diode 0.43 to ground and 5.000 V with power applied; no known-good resistance reading is listed. With the board off, measure diode mode from PP5V_S5 to ground, then power up and check the 5 V. A diode reading far from 0.43 or a missing 5 V usually points to a short or a fault in the enable/regulator side, but that's a likely cause, not confirmed.

PPVCCPCH_S5G0.1501.00085.000R
AI: what PPVCCPCH_S5G is and how to check it

PPVCCPCH_S5G is a standby (S5/SUS) rail feeding the PCH, as its name suggests; it is generated at step 30 of the power sequence, after PP3V3_S5G and the PGA loop to ENVR5 on U7800. Known-good readings here are diode 0.150, voltage 1.000 and resistance 85.000R, though the archive gives no condition for them, so treat them as a guide. Check it with the board unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from known-good usually points to a short or a rail that isn't being enabled, but one reading alone doesn't confirm a bad part.

S4 5

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.47––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail that comes up in the S4 stage of the power sequence (from its name), after PM_SLP_S4_L enables PM_EN_P3V3S4. The only known-good reading here is a diode value of 0.47; no known-good voltage is listed. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage while it should be enabled. A diode reading far from 0.47 usually points to a short or leak on the rail, but one reading isn't proof — confirm with a second measurement before replacing anything.

PP3V3_S4_WLS0.47––
AI: what PP3V3_S4_WLS is and how to check it
  • What it is: PP3V3_S4_WLS is a 3.3 V rail that comes up at the S4 stage of the power sequence, per its name. The "WLS" suffix usually suggests a wireless (Wi-Fi/Bluetooth) supply, but that is general naming, not confirmed by this board's data.
  • Known-good reading: diode 0.47 to ground, from the readings archive. No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.47. Then apply power and confirm the rail reaches about 3.3 V once the S4 stage is enabled (after PM_SLP_S4_L in the sequence).
  • If it's far off: a much lower diode reading points to a short or a failing load on the rail; a correct diode reading but no voltage points upstream, to the enable or regulator feeding it. Treat the 0.47 as a guide only, since community readings vary with board state.
PP5V_S40.4205.000–
AI: what PP5V_S4 is and how to check it

PP5V_S4 is the 5V rail that comes up in the S4 startup stage, judged from its name and the sequence note that it appears once PM_SLP_S4_L is generated. The archive lists a known-good diode reading of 0.420 and 5.000 V with power applied; treat these as a community guide, not a guaranteed value. With the board unpowered, measure diode mode from PP5V_S4 to ground and compare with 0.420. Then power up and check for 5 V, ideally after PM_SLP_S4_L is present. A diode reading far below 0.420 suggests a short or leaky load on the rail; a missing 5 V with a normal diode reading points upstream to the enable and S4 sequence rather than the rail itself.

PP5V_S4_TPAD_CONN0.44––
AI: what PP5V_S4_TPAD_CONN is and how to check it

PP5V_S4_TPAD_CONN is a 5V rail for the trackpad connector, enabled in the S4 stage of the power sequence (from its name). The only known-good reading here is diode mode 0.44; no known-good voltage or resistance is listed.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.44.
  • Then apply power and check for 5V, after PM_SLP_S4_L has been generated and PP5V_S4 is present.
  • A diode reading far below 0.44 suggests a short or leaky part on the rail; a far higher or open reading suggests a broken connection. Confirm with a second measurement before replacing anything.
PPVIN_S4_TPAD_FUSE0.45013.100–
AI: what PPVIN_S4_TPAD_FUSE is and how to check it

PPVIN_S4_TPAD_FUSE is a trackpad input rail in the S4 startup stage, judging from its name (S4 = the S4 power state). Known-good readings from the archive: diode 0.450 to ground and 13.100 V with power applied; no condition is recorded, so treat these as a guide only. Check it unpowered in diode mode from the fuse to ground, then power the board and measure the voltage on it. A diode reading far below 0.450 suggests a short or leaky load on the rail; a much higher one suggests an open path. No known-good resistance reading is available here, so compare against a matching rail or a known-good board if you need one.

S3: memory 5

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFDQ_A0.76––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail; the "S3" in its name places it in the memory stage of the power sequence. The only known-good figure here is a diode reading of 0.76 to ground, with no condition noted; there is no known-good voltage or resistance reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.76 usually points to a short or a damaged part on that net, but one reading isn't proof, so confirm with a voltage measurement before replacing anything.

PP1V_S30.230.997–
AI: what PP1V_S3 is and how to check it

PP1V_S3 is the 1V rail for the S3 (memory) state, as the name indicates; in the startup sequence it appears after PM_EN_P1VS3 reaches U8230 pin 2 (ON), alongside PP5V_S4, PP3V3_S4 and PP1V2_S3.

  • Known-good from the archive: diode 0.23 and voltage 0.997. These are community readings and only a guide.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power up and measure the voltage at the rail.
  • No known-good resistance reading here; compare against a matching rail or a known-good board.
  • A voltage far from about 1V points at the enable or the rail's regulator; a diode reading far from 0.23 suggests a short or open on the rail, but confirm with more than one reading before replacing anything.
PP1V2_S30.1971.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail that comes up in the S3 (memory) stage, judging from its name. The archive lists diode 0.197 and voltage 1.200 as known-good readings, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far from 1.2 V or a diode reading well off 0.197 points to a problem on that rail or its source, but one reading alone doesn't confirm a bad part. No known-good resistance reading here.

PP1V2_S3_REG0.2001.200–
AI: what PP1V2_S3_REG is and how to check it

PP1V2_S3_REG is a 1.2 V rail in the S3 (memory) startup stage, judged from its name; the board data doesn't name the parts on it. Known-good readings here are diode 0.200 and voltage 1.200, community-contributed and a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.200 suggests a short or leaky load on the rail; a voltage well off 1.200 points to the rail not being enabled or its regulator failing. There is no known-good resistance reading here, so compare against a matching rail or a known-good board.

PP1V8_S30.28––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail enabled at the S3 stage, which the name places in the memory power group; the sequence notes show it generated from U8200 pin 8 at 1V8 after PM_EN_P1V8S3 arrives at U8200 pin 5. The only known-good reading here is a diode value of 0.28 to ground; there is no known-good voltage reading in this data.

  • With the board unpowered, diode mode from PP1V8_S3 to ground should read about 0.28; a much lower value suggests a short on the rail.
  • With power applied, check for 1.8 V at U8200 pin 8 once PM_EN_P1V8S3 is present at pin 5.
  • A missing 1.8 V with the enable present points at U8200 or its feedback/inductor path; a low diode reading points at a shorted load. These are likely causes, not confirmed ones, so confirm with a second measurement before replacing anything.

S0: running 33

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V_OPC_S00.151.055–
AI: what PP1V_OPC_S0 is and how to check it

PP1V_OPC_S0 is a 1.0 V S0 rail; the name indicates it is a 1 V supply that comes up in the S0 (running) state, and the sequence notes place it at U7700 pin 2 (VLDOIN), generated once PP1V8_S3 is present. Known-good readings here are diode 0.15 and voltage 1.055. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.15 suggests a short or a faulty component on the rail; a voltage far from 1.055 with a normal diode reading points upstream, to its enable or source rail. No known-good resistance reading is listed for this rail.

PP1V_S0G0.21––
AI: what PP1V_S0G is and how to check it

PP1V_S0G is a 1 V rail in the S0 (running) state, judged from its name; the sequence lists it as generated once PP1V8_S3 is up, in the step that also produces PP1V2_S0G and PP1V_OPC_S0. The only known-good reading here is diode 0.21 to ground, with no condition recorded; there is no known-good voltage value in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.21 usually points to a short or a leaky part on the rail, but a single reading isn't proof, so compare with the matching rail on the other side of the pair before replacing anything.

PP1V_S0SW_PCHCLKOL––
AI: what PP1V_S0SW_PCHCLK is and how to check it
  • What it is: From the name, PP1V_S0SW_PCHCLK is a 1 V rail for the PCH clock in the S0 (running) state. The board data doesn't name the parts or loads on this net.
  • Known-good readings: The archive lists diode mode to ground as OL. No voltage or resistance known-good value is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with the OL guide. Then power up and measure the voltage, ideally once the board is in S0.
  • If it's far off: A short or much lower diode reading points to a fault on the rail or its load; a missing voltage with a normal diode reading points upstream, to its enable or source. Treat OL as a guide only, since community readings vary with board state.
PP1V2_S0G0.201.200–
AI: what PP1V2_S0G is and how to check it

PP1V2_S0G is a 1.2 V rail in the S0 (running) state, judged from its name; the sequence lists it as generated around step 39, after PP1V8_S3 comes up. Known-good readings here: diode 0.20 to ground and 1.200 V with the board powered in S0. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.20 suggests a short or leaky load on the rail; a correct diode reading with missing or low voltage points upstream at its enable or source regulator. No known-good resistance reading is recorded for this rail.

PP1V8_S00.34––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail in the S0 (running) state, judging by its name; it appears in the power sequence at step 41, after PM_PCH_SYS_PWROK, PM_EN_P1V8S0 and PPVCCIO_S0G, and is listed as present at 1V8.

  • Known-good from the archive: diode-to-ground reading of 0.34 in diode mode. No known-good voltage or resistance value is recorded here.
  • Check it unpowered first: board off and unplugged, meter in diode mode, black probe on ground, red on the PP1V8_S0 test point or a component on that net.
  • Then apply power and measure the DC voltage on the same point; it should come up only in the S0 state, so the board needs to reach step 41 of the sequence.
  • A diode reading far below 0.34 usually points to a short or a leaky part on the rail; far above it can mean an open trace or a missing connection. Confirm with a second measurement before replacing anything.
PP3V3_S00.3603.300–
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail that comes up in the S0 (running) state, judging by the "S0" suffix in its name. The archived reading for it is diode 0.360 and voltage 3.300; treat these as a guide, since community readings vary with board state.

  • Check it unpowered in diode mode from the rail to ground; a value far below 0.360 suggests a short or a leaky load on the rail.
  • Then power the board and confirm 3.300 V. The sequence notes place PP3V3_S0 at step 40, after PM_PCH_SYS_PWROK, so a missing 3.3 V usually points back to that enable chain rather than the rail itself.
  • No known-good resistance reading exists here for this rail.
PP3V3_S0_CPUTHMSNS_R0.40––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it
  • What it is: PP3V3_S0_CPUTHMSNS_R is a 3.3 V S0 (running-state) rail, judging by its name: a CPU thermal-sense supply that is present once the board is in S0.
  • Known-good reading: diode 0.40 to ground, from the readings archive. That's a community guide, not a factory spec, and no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.40; then power up and confirm roughly 3.3 V once the board reaches S0.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail, while no voltage in S0 points to the rail's enable or source not coming up. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_LCD0.512––
AI: what PP3V3_S0SW_LCD is and how to check it
  • What it is: PP3V3_S0SW_LCD is a 3.3 V switched LCD rail. The "S0" in the name marks it as a running-state rail, and "SW" suggests it is switched on by a control signal rather than always on (general reading of the name, not from board data).
  • Known-good reading: diode 0.512 to ground, from the community archive; treat it as a guide, since readings vary with board state. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.512. Then apply power, bring the board to S0, and measure the rail voltage; no known-good voltage is listed.
  • If far off: a much lower diode reading points to a short or leaky load on the rail, and a missing voltage points to the switch or its enable. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_LCD_R0.56––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is a switched 3.3 V LCD rail; the S0 in the name indicates it belongs to the running (S0) state, and the SW/LCD part suggests it is switched on for the display. The only known-good reading here is a diode value of 0.56 to ground; there is no known-good voltage reading for this rail in the data.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.56 (a community figure, so a guide only).
  • Then apply power and check the rail sits near 3.3 V once the board is in S0.

A diode reading far below 0.56 usually points to a short or a leaky part on the rail; a reading far above it can mean an open path. Confirm with the voltage measurement before suspecting any part, since a single reading can be misleading.

PP3V3_S0SW_LCD_R10.56––
AI: what PP3V3_S0SW_LCD_R1 is and how to check it
  • What it is: PP3V3_S0SW_LCD_R1 is a 3.3 V LCD-related rail, from the name: "S0" means it belongs to the running (S0) state and "SW" suggests a switched rail, so it's likely gated on only when the display section is enabled. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0.56 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V when the board is in S0 and the display is enabled.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a correct diode reading with no voltage points to the rail not being enabled or its source missing. Confirm with a second measurement before replacing anything.
PP3V3_TBT_X_S00.363.300–
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is the 3.3 V S0 (running-state) rail for the Thunderbolt X side, inferred from its name; the board data doesn't list which parts it feeds. Known-good readings in the archive: diode 0.36 to ground and 3.300 V with the board running. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A far-off diode reading usually points to a short or a damaged part on the rail; no known-good resistance reading is recorded here, so compare against a matching net or a known-good board.

PP5V_S00.45––
AI: what PP5V_S0 is and how to check it
  • What it is: PP5V_S0 is a 5 V rail in the S0 (running) state, inferred from the name; the power sequence lists it as the last step, "PP5V_S0 present (5V0)".
  • Known-good reading: diode 0.45 to ground (community value, a guide only; it varies with board state). No known-good voltage reading is recorded here.
  • How to check: with the board unpowered, diode mode from PP5V_S0 to ground; then power up and measure the voltage, expecting about 5 V.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a correct diode reading with no 5 V points upstream to its enable and the S0 sequence steps before it.
PP5V_S0_ALSCAM_F0.417––
AI: what PP5V_S0_ALSCAM_F is and how to check it

PP5V_S0_ALSCAM_F is a 5 V S0 (running-state) rail, most likely feeding the camera circuit — that's from the name, not from board data. The only known-good reading here is a diode value of 0.417 to ground; no known-good voltage or resistance is recorded.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. A reading far from 0.417 usually points to a short or a leaky part on that rail.
  • Then power the board and measure the voltage; it should come up only in S0, after the S3/S0 rails are up (general sequence knowledge, not from this board's data).
  • If the diode value is well off, suspect a shorted load on the rail before replacing anything.
PP5V_S0_BKLT_A0.417––
AI: what PP5V_S0_BKLT_A is and how to check it
  • What it is: PP5V_S0_BKLT_A is a 5 V backlight rail in the S0 (running) state, from its name. It isn't named in the power sequence notes, so its exact origin isn't documented here.
  • Known-good reading: diode 0.417 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.417 suggests a short or leaky load on the rail; a missing voltage with a normal diode reading points upstream, to the enable or source feeding it. Treat these as a guide, not a confirmed fault.
PP5V_S0_BKLT_D0.419––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the 5V backlight rail that comes up in the S0 (running) state, judging from its name. The archive lists one known-good reading: diode mode to ground 0.419, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure the voltage, which should be about 5V once the board is in S0. No known-good voltage reading is recorded here. A diode reading far below 0.419 usually points to a short or a leaky load on the rail, while a much higher one suggests an open path; confirm with a second measurement before replacing anything.

PP5V_S0_P1VOPC0.45––
AI: what PP5V_S0_P1VOPC is and how to check it
  • What it is: The name indicates a 5 V rail (PP5V) in the S0 running state, feeding the P1VOPC supply. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0.45 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then apply power and measure the DC voltage; it should come up at the S0 stage, after PP5V_S0 in the sequence.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a much higher one suggests an open feed. Confirm with the voltage before replacing anything.
PP5V_S0SW_LCD0.512––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is a switched 5 V LCD rail; the "S0" part of the name marks it as a running-state rail, and "SW" suggests it is switched on rather than always present (this is from the name, not the data). The only known-good reading here is diode 0.512 in diode mode, with no condition recorded; there is no known-good voltage reading for this rail. To check it, power the board off and measure diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.512 can point to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PPVCCCPU_S0G0.0051.8005.800R
AI: what PPVCCCPU_S0G is and how to check it

PPVCCCPU_S0G is the CPU core power rail; the "S0" suffix means it is a running-state rail (from the name). The archive lists diode 0.005, voltage 1.800 and resistance 5.800R, but no condition is recorded, so treat these as a guide only.

  • With the board unpowered, measure diode mode from PPVCCCPU_S0G to ground; a very low reading like the listed 0.005 is normal for a CPU core rail because of its low impedance.
  • Then apply power and check the voltage, which should come up near 1.800 as the board reaches S0.
  • No known-good value of a kind beyond these is available here.

A voltage far from known-good points to the CPU power stage not enabling or a short on the rail, but that is a likely cause, not a confirmed one.

PPVCCCPU_S0G_PH10.0051.8005.800R
AI: what PPVCCCPU_S0G_PH1 is and how to check it

PPVCCCPU_S0G_PH1 is a CPU core power rail: the "S0" state in its name means it is up when the board is running, and "PH1" suggests a phase output of the CPU VRM (that part is from the name, not the data). The archive lists a known-good diode reading of 0.005, voltage 1.800 and resistance 5.800R; treat these as a guide, since they come from community readings and vary with board state.

  • Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage.
  • A diode reading far from 0.005 to ground usually points to a short or a failed phase component; a voltage well off 1.800 with the board in S0 points to the VRM or its enable not coming up.
  • No known-good value is listed for conditions other than those above, so compare against a matching rail or a known-good board.
PPVCCCPU_S0G_PH20.0051.8005.800R
AI: what PPVCCCPU_S0G_PH2 is and how to check it

PPVCCCPU_S0G_PH2 is a CPU core power rail; the S0 in the name indicates it's a running-state rail, and PH2 suggests a second phase of the CPU VCC supply (from the name, not confirmed by parts data). Known-good readings here: diode 0.005, voltage 1.800, resistance 5.800R — community values, so treat them as a guide. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode reading far from 0.005 or a missing 1.8 V usually points to a short or a dead phase, but confirm with a second measurement before replacing anything.

PPVCCGT_S0G0.0041.8002.480R
AI: what PPVCCGT_S0G is and how to check it

PPVCCGT_S0G — the name indicates the graphics core (GT) supply rail, active in the S0 (running) state. Known-good readings from the archive: diode 0.004 to ground, 1.800 V with power applied, and 2.480R resistance. Note the very low diode value is normal for a heavy CPU/GPU core rail, so it is not a short by itself.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power up and measure the voltage at the rail.
  • A voltage far from 1.800 V, or a diode reading clearly different from 0.004, usually points to the rail not being enabled or to a fault on the rail; compare against a known-good board before condemning anything.

No known-good reading of other kinds is listed here.

PPVCCGT_S0G_PH10.0041.8002.48R
AI: what PPVCCGT_S0G_PH1 is and how to check it

PPVCCGT_S0G_PH1 is a power rail; from its name it is a graphics/GT core supply in the S0 (running) state, and "PH1" suggests a switching phase node. The archive lists known-good readings of diode 0.004, voltage 1.800 and resistance 2.48R, but no condition is recorded, so treat them as a guide only. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode or resistance far from 0.004 / 2.48R usually points to a short or a failed phase component, but one reading alone doesn't confirm a bad part; compare with the matching phase on a known-good board.

PPVCCGT_S0G_PH20.0041.8002.480R
AI: what PPVCCGT_S0G_PH2 is and how to check it
  • What it is: From the name, PPVCCGT_S0G_PH2 is a CPU graphics core supply rail (VCCGT), in the S0 running state, phase 2 of a multiphase regulator. "PH2" suggests it's one phase output, so it may only be present under graphics load.
  • Known-good readings (community archive, guide only): diode 0.004, voltage 1.800, resistance 2.480R. No condition is recorded for these.
  • How to check: Power off and unplug, then diode-mode from the rail to ground. Then power on and measure the voltage.
  • If far off: a diode near 0.004 to ground is normal for a low-voltage CPU rail, so a much higher diode or missing voltage points to the phase's regulator or its enable, not the CPU. These are likely causes, not confirmed ones.
PPVCCGT_S0G_PH30.0041.8002.480R
AI: what PPVCCGT_S0G_PH3 is and how to check it

PPVCCGT_S0G_PH3 — reference note

  • The name marks this as a graphics core (GT) supply rail in the S0 running state; the PH3 suffix suggests a switching phase output. That reading is from the name, not from a schematic.
  • Known-good readings from the archive: diode 0.004 to ground, voltage 1.800 V, resistance 2.480R. These are community figures and vary with board state, so treat them as a guide only.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • A diode or resistance far above known-good usually points to an open or missing connection feeding the rail; a voltage far off 1.800 V points to the rail not regulating. No known-good waveform or current reading exists here, so compare against a matching phase or a known-good board before condemning anything.
PPVCCIO_S0G0.050.950–
AI: what PPVCCIO_S0G is and how to check it
  • What it is: PPVCCIO_S0G is the S0-state VCCIO rail (the "S0" and "VCCIO" parts come from the name), so it belongs to the running stage of the power sequence. The notes place it at step 41, after PM_PCH_SYS_PWROK and PM_EN_PVCCIO, feeding PP1V8_S0.
  • Known-good readings: diode 0.05 and 0.950 V, from the community archive with no stated condition — treat them as a guide only.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage. No known-good resistance reading here.
  • If far off: a much higher diode reading or missing voltage points to the rail not being enabled or its regulator not switching; a near-zero diode reading suggests a short on the rail. Confirm with the enable signal before replacing anything.
PPVCCOPC_S0G0.07––
AI: what PPVCCOPC_S0G is and how to check it
  • PPVCCOPC_S0G is a power rail; the S0 suffix indicates the running state (from the name), and "VCC" rails are supply voltages. The archive lists one known-good reading: diode 0.07.
  • To check it, power the board off and measure diode mode from the rail to ground, then measure its voltage with power applied.
  • No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A diode reading far from 0.07 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.
PPVCCSA_S0G0.0081.5009.600R
AI: what PPVCCSA_S0G is and how to check it

PPVCCSA_S0G is a running-state (S0) supply rail; the "VCCSA" part of the name usually means the CPU's system-agent supply, but that is general naming, not from this board's data. Known-good readings here: diode 0.008, voltage 1.500 V, resistance 9.600R — community values, a guide only, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A voltage far from 1.500 V or a diode/resistance far from these points to a short or a missing enable on that rail, but one reading alone doesn't confirm a bad part. No known-good value of another kind is listed here.

PPVCCSA_S0G_R0.0081.5009.600R
AI: what PPVCCSA_S0G_R is and how to check it

PPVCCSA_S0G_R — the S0 in the name marks it as a running-state (S0) rail, and VCCSA by convention is the CPU's system-agent supply (that part is general naming, not from this board's data). The archive lists diode 0.008, voltage 1.500 V and resistance 9.600R for it, with no stated condition, so treat these as a guide.

  • Check with the board unpowered: diode mode from the rail to ground, then resistance to ground.
  • Then power up and measure the voltage on the rail.
  • A diode or resistance far below the listed values usually points to a short or a leaky load on the rail; a voltage well off 1.500 V points to the rail not being enabled or its regulator failing.
  • No known-good comparison exists here beyond these three figures, and one reading alone doesn't condemn a part.
PPVIN_S0SW_LCDBKLT0.810.86012.900–
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the backlight input rail for the LCD, from its name: an S0 (running) switched supply feeding the display backlight. Known-good readings in the archive are diode 0.81 and 0.860 to ground, and 12.900 V with the board running; treat these as a guide, not a spec. Check it unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below the known-good values suggests a short or leaky load on the rail; no known-good resistance reading is recorded here.

PPVIN_S0SW_LCDBKLT_F0.45013.100–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it
  • What it is: the LCD backlight input rail, in the S0 (running) state — inferred from the name PPVIN_S0SW_LCDBKLT_F, not from a schematic.
  • Known-good readings (community guide): diode 0.450 to ground, and 13.100 V with the board powered and running.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage. No known-good resistance reading here.
  • Far from known-good: a much lower diode reading usually points to a short or leaky part on the rail; a missing or low voltage with a normal diode reading points upstream, to the backlight supply or its enable. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT_R0.320.45013.100–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it
  • What it is: from the name, the input rail feeding the LCD backlight switch in the S0 (running) state. The data doesn't name the parts on this net.
  • Known-good readings (community archive, guide only): diode 0.32 and 0.450 to ground, and 13.100 V with the board running. No known-good resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the voltage.
  • If it's far off: a low diode reading or missing voltage usually points to a short or a dead feed on that rail, but one reading alone doesn't confirm a bad part. Compare with the matching net on the other side of the pair before replacing anything.
PPVOUT_S0_LCDBKLT1.1401.15055.000–
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT — the "S0" in the name indicates it belongs to the running (S0) power state; "LCDBKLT" indicates it is the LCD backlight rail, so it is the boost output that drives the display backlight, not a logic supply.

  • Known-good readings from the archive: diode mode to ground 1.140 and 1.150, and 55.000 V with power applied. These are community readings and only a guide; no condition is recorded for them.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage, ideally at the backlight connector or a test point on the rail.
  • A diode reading well below the known-good pair suggests a short or a leaky part on the rail; a voltage far from 55 V with the display on suggests the backlight boost circuit is not running or is being shut down. No known-good resistance reading exists for this rail.
  • Treat a single reading as a hint, not proof, and confirm with a second measurement before replacing anything.
PPVTT_S00.150.599–
AI: what PPVTT_S0 is and how to check it
  • What it is: PPVTT_S0 is a rail whose "S0" suffix marks it as a running-state rail (from the name); the "VTT" part usually means a termination rail in general electronics, though this board's data doesn't spell out its source or loads.
  • Known-good readings (community guide): diode 0.15 to ground, and 0.599 V with the board powered in S0. No known-good resistance value here.
  • How to check: power off and unplug, then diode mode from the rail to ground; after that, power up into S0 and measure the voltage.
  • If it's far off: a much lower diode reading can suggest a shorted load or part on the rail, while a missing or wrong voltage points to the rail not being enabled or its source failing. Confirm with a second measurement before replacing anything.

Repair notes

Power Sequences

Turning on

1) F3000 5V VBUS 2) UPC_XA_GATE2 and UPC_XA_GATE1 7~10V 3) PPDCIN_G3H 5V 4) R7075 pin 1 (VDDA) to R7075 pin 2 (VDDP) and ensure R7075 is 4R7 5) PM_EN_P3V3_G3H signal from U7000 to U6990 pin 10 6) PP3V3_G3H present to; -> U5000 as PP3V3_S5_SMC for SMC -> U3100 at C3100 pin 1 for CD3215 -> U1900 pin 1 and U1900 pin 11 for Clock generator 7) Check around CD3215 for LDO voltages -> PP3V3_UPC_XA_LDO -> PP1V8_UPC_XA_LDOA -> PP1V1_UPC_XA_LDO_BMC -> SYSCLK_CLK32K_PCH RTC 32kHz -> SMC_CLK12M_EN 12MHz Enable from U1900 8) SYSCLK_CLK12M_SMC 12Mhz clock to SMC from RTC 9) BUF_SMC_RESET_L Check for high 10) 11) Communications between U7000 and U5000 12) USBC_XA_CC1 to U3100 13) PP20V_USBC_XA_VBUS 20V at F3000 pin 1 14) PPDCIN_G3H 20V at Q3100 pin 8 14.1) R7061 pin 1 AUX_DET ~15V 15) CHGR_ACOK / SMC_BC_ACOK output at R5187 pin 1 16) I2C comms between U5000 and U7000 17) Q7030 turned on to let 20V pass through L7030 to Q7040 18) F7000 pin 1 20V, also present on D6905 pin 1 via R6905 pin 1 19) SMC_PM_G2_EN enabled on R7829 pin 1 out of SMC to U7800 pin 49 20) PMIC_EN_P3V3S5 asserted from U7800 to U7890 pin 2 to emit; 21) => PM_EN_P5VS5 at U7890 pin 4 => PM_EN_PVXS5 at U7890 pin 4 22) PP5V_S5 at 5V 23) PP3V3_S5 at 3V3 in to U8205 pin 1 24) PM_PGOOD_P3V3S5 out of U7650 pin 20 assert high 25) PM_DSW_PWRGD out of U5000 pin 158 to Q9902 pin 5 assert high 26) PM_SLP_SUS_L out of CPU to PM_EN_P1V8 at R1458 pin 1 (TP nearby) 27) PP1V8_S5G present at 1V8 on L7930 pin 2 ( also turns on U8205 ) 28) PP3V3_S5G present at 3V3 out of U8205 pin 13 29) PGA loops to ENVR5 on U7800 30) PPVCCPCH_S5G generated 31) PGVR5 loops to ENVR1 on U7800 32) PP1V_S5G generated and fed in to U0500 VCCPRIM_1P0 33) PM_RSMRST_L out of U7800 in to U5000] TURNING ON Phase 34) SMC_ONOFF_L received 35) PM_PWRBTN_L sent to U0500 / CPU 36) PM_SLP_S5_L generated by U0500 to U5000 / U7800:ENC 37) PM_SLP_S4_L generated by U0500 to U5000 / U7800:ENB => P5VS4_EN sent to U7650 pin 4 (EN1) => PM_EN_P3V3S4 sent to U8210 pin 3 (EN1) => PM_EN_P1VS3 sent to U8230 pin 2 (ON) 38) PM_EN_P1V8S3 sent to U8200 pin 5 (ON) => PP5V_S4 present (5V) => PP3V3_S4 present (3V3) => PP1V2_S3 present (1V2) => PP1V_S3 present (1V0) => PM_SLP_S3_L present to U7700 pin 16 (as P1V0PC_EN (S5)) 39) PP1V8_S3 generated from U8200 pin 8 at 1V8 => PP1V2_S0G present (1V2) => PP1V_S0G present (1V0) => PM_GOOD_P4VS4 from U7650 pin 5 (PGOOD1) => PP1V_OPC_S0 from and used at U7700 pin 2 (VLDOIN) => PM_PGOOD_PVDDQ from U7800 in to U7896 pin 2 => PM_EN_P3V3S0 from U7850 pin 4 40) PM_PCH_SYS_PWROK present => PM_EN_PVCCIO present => PM_EN_P1V8S0 present => PP3V3_S0 present (3V3) 41) PPVCCIO_S0G present => PP1V8_S0 present (1V8) => PM_PGOOD_CPUVCC present 42) PP5V_S0 present (5V0)

Every net with a reading

NetDiodeVoltageResistance
8409_ASP1_LRCLK_R0.52––
8409_ASP1_SCLK_R0.52––
8409_ASP1_SDOUT_R0.36––
8409_ASP2_LRCLK_R0.67––
8409_ASP2_SCLK_R0.53––
8409_ASP2_SDOUT_R0.53––
8409_DMIC1_CLK_R0.75––
8409_DMIC1_DATA0.75––
8409_HDA_SDIN0_R0.50––
8409_I2C_SCL0.49––
8409_I2C_SDA0.51––
8409_SPKR_ID00.76––
8409_SPKR_ID10.74––
AC_SHIELD_SSDOL––
ACT_THERM_TRIP_L0.74––
ADDR_FL0.38––
ADDR_FR0.37––
ADDR_RR0.35––
AGND_P3V3G3H0.00––
AGND_U75100.02––
AGND_U75200.02––
AGND_U75300.01––
ALERT_L0.175––
ALL_SYS_PWRGD0.48––
AMP_FL_LRCLK0.533––
AMP_FL_SCLK0.357––
AMP_FL_SDOUT0.355––
AMP_FR_LRCLK0.51––
AMP_FR_SCLK0.54––
AMP_FR_SDOUT0.34––
AMP_RL_LRCLK0.52––
AMP_RL_SCLK0.558––
AMP_RL_SDOUT0.352––
AMP_RR_LRCLK0.51––
AMP_RR_SCLK0.54––
AMP_RR_SDOUT0.34––
AP_CLKREQ_L0.52––
AP_DEV_WAKE0.550.000–
AP_PCIE_WAKE_L0.523.300–
AP_RESET_L0.603.300–
AP_S0IX_WAKE_L0.65––
AP_S0IX_WAKE_SEL0.66––
ARKANOID_P5OL––
ARKANOID_P7OL––
AUD_3V3_S00.36––
AUD_ASP1A_LRCLK0.52––
AUD_ASP1A_SCLK0.53––
AUD_ASP1A_SDOUT0.355––
AUD_ASP1B_LRCLK0.51––
AUD_ASP1B_SCLK0.52––
AUD_ASP1B_SDOUT0.34––
AUD_ASP2_LRCLK0.64––
AUD_ASP2_SCLK0.53––
AUD_ASP2_SDIN0.66––
AUD_ASP2_SDOUT0.52––
AUD_CONN_HP_LEFT0.68––
AUD_CONN_HP_RIGHT0.70––
AUD_CONN_HP_SENSE_L1.300––
AUD_CONN_HP_SENSE_R1.31––
AUD_CONN_RING20.01––
AUD_CONN_RING2_XW0.64––
AUD_CONN_SLEEVE0.01––
AUD_CONN_SLEEVE_XW0.64––
AUD_CONN_TIP_SENSEOL––
AUD_HP_PORT_CH_GND0.01––
AUD_HP_PORT_L0.66––
AUD_HP_PORT_R0.70––
AUD_HP_PORT_US_GND0.00––
AUD_HP_SENSE_L1.300––
AUD_HP_SENSE_R1.32––
AUD_I2C_SCL0.50––
AUD_I2C_SDA0.51––
AUD_PWR_EN0.52––
AUD_RING_SENSE0.00––
AUD_TIP_SENSE1.47––
BANJO_DRVHVR10.64––
BANJO_DRVHVR1_R0.63––
BANJO_DRVHVR30.56––
BANJO_DRVHVR3_R0.60––
BANJO_DRVHVR40.74––
BANJO_DRVHVR4_R0.74––
BANJO_DRVHVR50.62––
BANJO_DRVHVR5_R0.61––
BANJO_DRVLVR10.48––
BANJO_DRVLVR1_R0.48––
BANJO_DRVLVR30.48––
BANJO_DRVLVR40.48––
BANJO_DRVLVR4_R0.48––
BANJO_DRVLVR50.48––
BANJO_DRVLVR5_R0.48––
BANJO_ENVR10.45––
BANJO_ENVR20.45––
BANJO_ENVR30.45––
BANJO_ENVR40.46––
BANJO_ENVR50.44––
BANJO_FBLDO10.16––
BANJO_FBLDO1_R0.15––
BANJO_FBVR1_N0.00––
BANJO_FBVR1_P0.12––
BANJO_FBVR1P0.11––
BANJO_FBVR2_P0.36––
BANJO_FBVR2R_N0.08––
BANJO_FBVR2R_P0.36––
BANJO_FBVR3RP0.08––
BANJO_FBVR4_N0.01––
BANJO_FBVR4_P0.22––
BANJO_FBVR4P0.20––
BANJO_FBVR5_N0.00––
BANJO_FBVR5_P0.90––
BANJO_FBVR5P0.08––
BANJO_ILIMVR10.47––
BANJO_ILIMVR3LS0.46––
BANJO_ILIMVR40.47––
BANJO_ILIMVR5LS0.46––
BANJO_PGNDVR10.00––
BANJO_PGNDVR30.01––
BANJO_PGNDVR40.00––
BANJO_PGNDVR50.00––
BANJO_SWVR10.0441.00045.000R
BANJO_SWVR1_SNUBOL––
BANJO_SWVR1R0.11––
BANJO_SWVR20.3321.800–
BANJO_SWVR30.0500.950–
BANJO_SWVR40.201.200–
BANJO_SWVR4_SNUBOL––
BANJO_SWVR4R0.20––
BANJO_SWVR50.1501.00085.000R
BANJO_SWVR5_SNUBOL––
BANJO_SWVR5R0.01––
BANJO_VINLDO1S0.15––
BKLT_EN_R0.477––
BKLT_PWM_KEYB0.471––
BKLT_SCL0.469––
BKLT_SD0.52––
BKLT_SDA0.469––
BKLT_SENSE_OUT0.669––
BT_DEV_WAKE0.79––
BT_GPIO40.78––
BT_LOW_PWR_L–3.300–
BT_PWRRST_L0.78––
BT_SPI_CLK0.72––
BT_SPI_CS_L0.70––
BT_SPI_MISO0.63––
BT_SPI_MOSI0.65––
BT_TIMESTAMP0.78––
BT_UART_CTS_L0.46––
BT_UART_D2R0.43––
BT_UART_R2D0.46––
BT_UART_RTS_L0.43––
BTROM_HOLD_L0.73––
BTROM_WP_L0.73––
BUF_EDP_PANEL_PWR_EN0.54––
BUF_SMC_RESET_L0.69––
CAM_DEBUG_RESET_L0.77––
CAM_PWR_SEL0.82––
CAM_SENSOR_WAKE_L0.82––
CAM_TEST_MODE0.76––
CAM_TEST_OUT0.83––
CAM_UARTCTS0.77––
CAM_UARTRXD0.77––
CAM_XTAL_FREQ0.77––
CAM_XTAL_SEL0.77––
CAMERA_CLKREQ_L0.61––
CAMERA_PWR_EN0.56––
CAMERA_PWR_EN_PCH0.56––
CAMERA_RESET_L0.52––
CATERR_LEDOL––
CATERR_LED_LOL––
CHGR_AMON0.61––
CHGR_BMON0.61––
CLK25M_CAM_CLKN0.80––
CODEC_INT_L0.70––
CODEC_RESET_L0.71––
CODEC_WAKE_L0.72––
CPU_CATERR_L0.24––
CPU_CFG_RCOMP0.05––
CPU_CFG<0>0.26––
CPU_CFG<1>0.29––
CPU_CFG<2>0.29––
CPU_CFG<3>0.29––
CPU_CFG<4>0.28––
CPU_CFG<5>0.30––
CPU_CFG<7>0.30––
CPU_CFG<8>0.29––
CPU_CFG<9>0.29––
CPU_CFG<10>0.29––
CPU_CFG<11>0.29––
CPU_CFG<12>0.29––
CPU_CFG<13>0.29––
CPU_CFG<15>0.29––
CPU_CFG<16>0.29––
CPU_CFG<17>0.29––
CPU_CFG<18>0.29––
CPU_CFG<19>0.29––
CPU_DIMM_VREFCA0.72––
CPU_DIMMA_VREFDQ0.76––
CPU_DIMMB_VREFDQ0.32––
CPU_PECI0.30––
CPU_PECI_R0.27––
CPU_PROCHOT_L0.48––
CPU_RSVD_AK130.34––
CPU_VCCGTSENSE_P0.00––
CPU_VCCIOSENSE_N0.01––
CPU_VCCIOSENSE_P0.01––
CPU_VCCSASENSE_N0.00––
CPU_VCCSASENSE_P0.01––
CPU_VCCSENSE_N0.01––
CPU_VCCSENSE_P0.01––
CPU_VCCST_PWRGD0.42––
CPU_VCCST_PWRGD_R0.46––
CPU_VIDSCLK_R0.23––
CPU_VIDSOUT0.23––
CPU_ZVM_L0.37––
CPUHI_IOUT0.69––
CPUTHMSNS_ADDR_SEL0.08––
CPUTHMSNS_ALERT_L0.61––
CPUTHMSNS_D1_N0.64––
CPUTHMSNS_D1_P0.64––
CPUTHMSNS_D2_N0.64––
CPUTHMSNS_D2_P0.64––
CPUTHMSNS_FILT0.44––
CPUTHMSNS_GPIO0.54––
CPUVR_COMP0.558––
CPUVR_COMP_ROL––
CPUVR_FB0.460––
CPUVR_FB_R_10.16––
CPUVR_FB_R_21.60––
CPUVR_FB_R_30.10––
CPUVR_FCCM0.545––
CPUVR_IMON0.557––
CPUVR_ISEN10.558––
CPUVR_ISEN20.558––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS_R_NOL––
CPUVR_ISNS_R_POL––
CPUVR_ISNS1_N0.0051.8005.800R
CPUVR_ISNS1_P0.0051.8005.800R
CPUVR_ISNS2_N0.0051.8005.800R
CPUVR_ISNS2_P0.0051.8005.800R
CPUVR_ISUM_IOUTOL––
CPUVR_ISUM_N0.01––
CPUVR_ISUM_P0.178––
CPUVR_ISUMN_R0.093––
CPUVR_NTC0.558––
CPUVR_NTC_LOL––
CPUVR_PHASE20.00––
CPUVR_PWM10.548––
CPUVR_PWM20.549––
CPUVR_RTN0.000––
CPUVR_SW10.0051.8005.80R
CPUVR_SW20.0051.8005.800R
CPUVR_VCC0.4––
CPUVR_VIN0.4––
CPUVSENSE_IN0.01––
CS8409_VA_PLL0.60––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.49––
DIAG_LED_ENABLE_LOL––
DIV_PPBUS_G3HOL––
DIV_PPDCINOL––
DMIC1_CLK0.78––
DMIC1_DATA0.75––
DP_INT_HPD0.47––
DP_X_SNK_RBIAS0.78––
DP_X_SNK0_AUXCH_C_N0.27––
DP_X_SNK0_AUXCH_C_P0.27––
DP_X_SNK0_AUXCH_N0.38––
DP_X_SNK0_AUXCH_P0.39––
DP_X_SNK0_DDC_CLK0.58––
DP_X_SNK0_HPD0.56––
DP_X_SNK1_AUXCH_C_N0.27––
DP_X_SNK1_AUXCH_C_P0.27––
DP_X_SNK1_AUXCH_N0.38––
DP_X_SNK1_AUXCH_P0.39––
DP_X_SNK1_DDC_CLK0.58––
DP_X_SNK1_HPD0.56––
DP_XA_AUXCH_C_N0.40––
DP_XA_AUXCH_C_P0.40––
DP_XA_AUXCH_N0.80––
DP_XA_AUXCH_P0.80––
DP_XA_HPD0.59––
DP_XB_AUXCH_C_N0.38––
DP_XB_AUXCH_C_P0.39––
DP_XB_AUXCH_N0.81––
DP_XB_AUXCH_P0.81––
DP_XB_HPD0.57––
EDP_AUXCH_C_N0.200––
EDP_AUXCH_C_P0.200––
EDP_BKLT_EN0.54––
EDP_BKLT_PWM0.710.71––
EDP_COMP0.08––
EDP_INT_AUX_NOL––
EDP_INT_AUX_POL––
EDP_INT_ML_N<0>OL––
EDP_INT_ML_N<1>OL––
EDP_INT_ML_N<2>OL––
EDP_INT_ML_N<3>OL––
EDP_INT_ML_P<0>OL––
EDP_INT_ML_P<1>OL––
EDP_INT_ML_P<2>OL––
EDP_INT_ML_P<3>OL––
EDP_PANEL_PWR_EN0.55––
FAN_LT_PWM0.85––
FAN_LT_TACHOL––
GND0.000––
GND_5V3V3_AGND0.00––
GND_BKLT_SGND0.000––
GND_CAM_PVSSD0.00––
GTVR_BOOT10.61––
GTVR_BOOT20.62––
GTVR_BOOT30.61––
GTVR_BP10.62––
GTVR_BP20.62––
GTVR_BP30.61––
GTVR_COMP0.558––
GTVR_COMP_LOL––
GTVR_FB0.515––
GTVR_FB_L_21.16––
GTVR_FB_L_30.01––
GTVR_FCCM0.541––
GTVR_IMON0.558––
GTVR_ISEN10.558––
GTVR_ISEN20.558––
GTVR_ISEN30.558––
GTVR_ISNS_NOL––
GTVR_ISNS_POL––
GTVR_ISNS_R_NOL––
GTVR_ISNS_R_POL––
GTVR_ISNS1_N0.0041.8002.480R
GTVR_ISNS1_P0.0041.8002.480R
GTVR_ISNS2_N0.0041.8002.480R
GTVR_ISNS2_P0.0041.8002.480R
GTVR_ISNS3_N0.0041.8002.480R
GTVR_ISNS3_P0.0041.8002.480R
GTVR_ISUM_IOUTOL––
GTVR_ISUM_N0.00––
GTVR_ISUM_P0.121––
GTVR_ISUMN_R0.120––
GTVR_NTC0.559––
GTVR_NTC_ROL––
GTVR_PHASE10.02––
GTVR_PHASE20.02––
GTVR_PHASE30.01––
GTVR_PWM10.546––
GTVR_PWM20.547––
GTVR_PWM30.548––
GTVR_RTN0.000––
GTVR_SW10.004–2.48R
GTVR_SW20.004–2.48R
GTVR_SW30.0041.8002.48R
GTVSENSE_IN0.00––
HALL_SENSOR_LEFT0.46––
HALL_SENSOR_RIGHTOL––
HDA_BIT_CLK0.60––
HDA_BIT_CLK_R0.56––
HDA_RST_L0.60––
HDA_RST_R_L0.56––
HDA_SDIN00.50––
HDA_SDOUT0.60––
HDA_SYNC0.60––
HS_MIC_N0.733––
HS_MIC_P0.733––
I2C_ALS_SCL_CONN0.468––
I2C_ALS_SDA_CONN0.45––
I2C_BKLT_SCL0.48––
I2C_BKLT_SDA0.48––
I2C_CAM_SCL0.75––
I2C_CAM_SCL_CONN0.67––
I2C_CAM_SDA0.75––
I2C_CAM_SDA_CONN0.67––
I2C_CAM_SMBDBG_CLK0.78––
I2C_CAM_SMBDBG_DAT0.78––
I2C_TBT_X_SCL0.47––
I2C_TBT_X_SDA0.52––
I2C_TBT_XA_INT_L0.54––
I2C_TCON_SCL_CONN0.63––
I2C_TCON_SDA_CONN0.65––
I2C_UPC_XA_DBG_CTL_SCL0.53––
I2C_UPC_XA_DBG_CTL_SDA0.58––
I2C_UPC_XB_DBG_CTL_SCL0.76––
I2C_UPC_XB_DBG_CTL_SDA0.77––
ISNS_1V2S3_IOUTOL––
ISNS_1V2S3_NOL––
ISNS_1V2S3_POL––
ISNS_1VS5G_IOUTOL––
ISNS_1VS5G_NOL––
ISNS_1VS5G_POL––
ISNS_3V3LCD_IOUTOL––
ISNS_3V3S5_IOUTOL––
ISNS_3V3S5_NOL––
ISNS_3V3S5_POL––
ISNS_3V3SSD_IOUT0.67––
ISNS_3V3SSD_N0.3803.300–
ISNS_3V3SSD_P0.383.300–
ISNS_3V3WLS_IOUTOL––
ISNS_3V3WLS_NOL––
ISNS_3V3WLS_POL––
ISNS_5VS4_IOUTOL––
ISNS_5VS4_NOL––
ISNS_5VS4_POL––
ISNS_HS_COMPUTING_N0.46013.100–
ISNS_HS_COMPUTING_P0.46013.100–
ISNS_HS_COMPUTING_R_N0.37––
ISNS_HS_COMPUTING_R_P0.37––
ISNS_HS_SSD_N0.46––
ISNS_HS_SSD_P0.46––
ISNS_HS_TBT_N0.363.300–
ISNS_HS_TBT_P0.363.300–
ISNS_HS_TPAD_NOL––
ISNS_HS_TPAD_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.400.45013.100–
ISNS_LCDBKLT_P0.400.45013.100–
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_SSD_IOUT0.72––
ISNS_TBT_IOUTOL––
ISNS_TPAD_IOUTOL––
ISUMN_B_L_11.02––
ISUMN_C_L_11.02––
ITP_PMODE0.46––
JTAG_ISP_TDO0.53––
JTAG_TBT_TCK0.54––
JTAG_TBT_TDI0.54––
JTAG_TBT_X_TMS0.58––
JTAG_WLAN_SEL0.78––
JTAG_WLAN_TDI0.78––
KBD_BLC_GSLATOL––
KBD_BLC_GSSCKOL––
KBD_BLC_GSSINOL––
KBD_BLC_GSSOUTOL––
KBD_BLC_XBLANKOL––
KBD_I2C_SCLOL––
KBD_I2C_SDAOL––
KBD_INT_LOL––
L83_1V80.40––
L83_ASP_SDOUT_R0.64––
L83_FILTP0.804––
L83_FLYC0.40––
L83_FLYN0.58––
L83_FLYP0.43––
L83_GNDCP0.01––
L83_HSBIAS_FILT0.71––
L83_HSBIAS_FILT_REF0.62––
L83_LDO_EN0.520––
L83_VCP0.40––
L83_VCP_FILTN0.76––
L83_VCP_FILTP0.41––
L83_VL0.40––
L83_VP0.36––
LCD_IRQ_L0.47––
LCD_PWR_SLEW0.71––
LCD_PWR_SLEW_3V30.61––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.674––
LCDBKLT_FET_DRV0.436––
LCDBKLT_SW0.403––
LED_BKLTOL––
LED_BKLT_ROL––
LED_CATERROL––
LED_CATERR_ROL––
LED_DCIN0.01––
LED_DCIN_ROL––
LED_DS5OL––
LED_DS5_ROL––
LED_G3HOL––
LED_G3H_ROL––
LED_PBUSOL––
LED_PBUS_ROL––
LED_PLTRSTOL––
LED_PLTRST_ROL––
LED_PROCHOTOL––
LED_PROCHOT_ROL––
LED_S0IOL––
LED_S0I_ROL––
LED_S3OL––
LED_S3_ROL––
LED_S4OL––
LED_S4_ROL––
LED_S5OL––
LED_S5_ROL––
LID_OPENOL––
LID_OPEN_R0.70––
LPC_AD_R<0>0.56––
LPC_AD_R<1>0.56––
LPC_AD_R<2>0.55––
LPC_AD_R<3>0.56––
LPC_AD<0>0.60––
LPC_AD<2>0.59––
LPC_CLK24M_SMC0.58––
LPC_CLK24M_SMC_R0.56––
LPC_CLKRUN_L0.61––
LPC_FRAME_L0.59––
LPC_SERIRQ0.54––
MEM_CAM_ODT0.79––
MEM_CAM_ZQ_DDR0.24––
MEM_CAM_ZQ_S20.24––
MIPI_CLK_CONN_N0.368––
MIPI_CLK_CONN_P0.366––
MIPI_CLK_N0.40––
MIPI_CLK_P0.41––
MIPI_DATA_CONN_N0.36––
MIPI_DATA_CONN_P0.36––
MIPI_DATA_N0.40––
MIPI_DATA_P0.77––
MLB_BOARD_ID00.79––
MLB_BOARD_ID10.79––
MLB_BOARD_ID20.72––
MLB_BOARD_ID30.78––
MLB_BOARD_ID40.56––
MLB_RAMCFG00.79––
MLB_RAMCFG10.72––
MLB_RAMCFG20.51––
MLB_RAMCFG30.51––
MLB_RAMCFG40.51––
OPC_RCOMP0.05––
OPCE_RCOMP0.05––
P0V9_TBT_X_SVR_AGND0.00––
P1V2_CAM_SRVLXC_PHASE0.300-1.200–
P1V8S0SW_CT20.75––
P1V8S3SW_CT10.76––
P1V35_CAM_SRVLXD_PHASE0.2701.350–
P1VOPC_AGND0.00––
P1VOPC_DRVH0.67––
P1VOPC_DRVH_R0.64––
P1VOPC_DRVL0.44––
P1VOPC_DRVL_R0.46––
P1VOPC_EN0.44––
P1VOPC_ENS30.50––
P1VOPC_MODE0.53––
P1VOPC_PGND0.00––
P1VOPC_REFIN0.68––
P1VOPC_SNS0.16––
P1VOPC_SW0.15––
P1VOPC_TRIP0.74––
P1VOPC_VBST0.61––
P1VOPC_VREF0.63––
P1VOPC_VSW0.1501.055–
P1VOPC_VTT0.60––
P1VOPC_VTTREF0.50––
P1VS5GFUSE_RAMP0.72––
P3V3_TBT_X_SX_EN0.60––
P3V3_TBT_X_SX_EN_R0.61––
P3V3S0SW_CT20.754––
P3V3S4SW_CT10.764––
P3V3S5_COMP20.73––
P3V3S5_COMP2_ROL––
P3V3S5_CS2_L_N0.3803.300–
P3V3S5_CS2_L_P0.383.300–
P3V3S5_CSP21.33––
P3V3S5_DRVH0.93––
P3V3S5_DRVH_R0.91––
P3V3S5_DRVL0.56––
P3V3S5_DRVL_R0.54––
P3V3S5_EN0.47––
P3V3S5_RF0.57––
P3V3S5_SNUBROL––
P3V3S5_SW0.37––
P3V3S5_VBST0.62––
P3V3S5_VBST_R0.63––
P3V3S5_VFB20.56––
P3V3S5_VFB2_R0.37––
P3V3S5_VFB2_R20.39––
P3V3S5_VFB2_RROL––
P3V3S5_VSW0.3803.300–
P3V3S5GSW_CT10.75––
P5VP3V3_SKIPSEL0.47––
P5VP3V3_VREF20.47––
P5VP3V3_VREG30.54––
P5VS0SW_CT20.764––
P5VS4_COMP10.73––
P5VS4_COMP1_ROL––
P5VS4_CS1_L_N0.425.000–
P5VS4_CS1_L_P0.4205.000–
P5VS4_CSP11.35––
P5VS4_DRVHOL––
P5VS4_DRVH_R0.97––
P5VS4_DRVL_R0.54––
P5VS4_EN0.47––
P5VS4_SW0.42––
P5VS4_VBST0.62––
P5VS4_VBST_R0.58––
P5VS4_VFB10.56––
P5VS4_VFB1_R0.44––
P5VS4_VFB1_R20.45––
P5VS4_VFB1_RROL––
P5VS4_VSW0.4205.000–
P5VXX_EN0.47––
PANEL_P3V3_EN0.56––
PANEL_P3V3_EN_D0.71––
PANEL_P3V3_EN_DLY0.550––
PANEL_P5V_EN0.510––
PANEL_P5V_EN_D0.650––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.450––
PBUSVSENS_EN_L0.48––
PBUSVSENS_EN_L_DIVOL––
PCH_BT_UART_CTS_L0.48––
PCH_BT_UART_D2R0.48––
PCH_BT_UART_R2D0.42––
PCH_BT_UART_RTS_L0.43––
PCH_DDPB_CTRLDATA0.78––
PCH_DDPC_CTRLDATA0.78––
PCH_DIFFCLK_BIASREF0.78––
PCH_HSIO_PWR_EN0.56––
PCH_INTRUDER_L0.82––
PCH_JTAGX0.56––
PCH_OPIRCOMP0.06––
PCH_PCIE_RCOMP_N0.36––
PCH_PCIE_RCOMP_P0.36––
PCH_SRTCRST_L0.81––
PCH_STRP_TOPBLK_SWP_L0.77––
PCH_SUSACK_L0.48––
PCH_SUSWARN_L0.73––
PCH_USB2_COMP0.12––
PCH_USB2_VBUSSENSE0.77––
PCIE_CLK100M_AP_N0.35––
PCIE_CLK100M_AP_P0.35––
PCIE_CLK100M_SSD_C_N0.36––
PCIE_CLK100M_SSD_C_P0.36––
PCIE_CLK100M_TBT_X_N0.35––
PCIE_CLK100M_TBT_X_P0.35––
PCIE_SSD_R2D_N<0>OL––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_N<2>OL––
PCIE_SSD_R2D_N<3>OL––
PCIE_SSD_R2D_P<0>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_SSD_R2D_P<2>OL––
PCIE_SSD_R2D_P<3>OL––
PCIE_WAKE_L0.57––
PD_PPVIOE_SSDCLK0.00––
PD_SMC_CBC_ON0.60––
PD_SOC_UART_CTS_L0.56––
PD_TBA_AGATE0.62––
PD_TBA_MPM_DET0.61––
PD_TBA_SGATE0.62––
PD_UPC_XA_GPIO50.77––
PD_UPC_XA_GPIO60.77––
PD_UPC_XB_GPIO50.77––
PD_UPC_XB_GPIO60.76––
PD_VSNS_CPU_VCCGTX_TN0.00––
PDCINVSENS_EN_L_DIVOL––
PLT_RST_L0.393.300–
PLTRST_LED_LOL––
PM_CLK32K_SUSCLK_R0.56––
PM_DSW_PWRGD0.75––
PM_EN_CPUVCC_R0.423––
PM_EN_P1V8S00.54––
PM_EN_P1V8S0_RC0.813.320–
PM_EN_P1V8S30.47––
PM_EN_P1VS0G0.50––
PM_EN_P1VS30.46––
PM_EN_P3V3_G3H0.605.000–
PM_EN_P3V3_G3H_R0.605.000–
PM_EN_P3V3S00.66––
PM_EN_P3V3S0_RC0.81––
PM_EN_P3V3S40.47––
PM_EN_P3V3S5G0.47––
PM_EN_P5VS40.47––
PM_EN_PVCCIO0.45––
PM_EN_PVXS50.47––
PM_EN_S0_SW0.46––
PM_MEMVTT_EN0.37––
PM_OPC_ZVM_L0.54––
PM_PCH_PWROK0.42––
PM_PCH_PWROK_BUF0.71––
PM_PCH_SYS_PWROK0.453.200–
PM_PGOOD_CPUVCC0.464––
PM_PGOOD_EDRAM_R0.47––
PM_PGOOD_P1V80.47––
PM_PGOOD_P3V3S5G0.44––
PM_PGOOD_P5VS40.48––
PM_PGOOD_PVCCPCH0.45––
PM_PGOOD_PVDDQ0.44––
PM_PWRBTN_L0.583.300–
PM_RSMRST_L0.47––
PM_SLP_S0_L0.463.300–
PM_SLP_S0_OD_L0.50––
PM_SLP_S0S3_L0.50––
PM_SLP_S3_L0.453.300–
PM_SLP_S4_L0.473.300–
PM_SLP_S5_L–3.300–
PM_SLP_SUS_L0.473.300–
PM_SYSRST_L0.72––
PM_THRMTRIP_L0.29––
PMIC_ALLSYSPGD0.45––
PMIC_EN_P3V3S50.47––
PMIC_EN3V3SW0.52––
PMIC_EN5VSW0.47––
PMIC_ENA0.46––
PMIC_ENH0.515––
PMIC_ENLVA0.46––
PMIC_INT_L0.46––
PMIC_PCH_PWROK0.42––
PMIC_PGB0.47––
PMIC_PGD0.47––
PMIC_PGE0.47––
PMIC_PGH0.46––
PMIC_RSMRST_L0.45––
PMIC_SHUTDOWN_L0.46––
PMIC_SLVADDR0.47––
PMIC_SYSPWROK0.44––
PMIC_VCCST_PGD0.45––
PMIC_VDCSNS0.72––
PMIC_VSA0.34––
PMIC_VSB0.27––
PMIC_VSC0.42––
PMIC_VSD0.48––
PMIC_VSE0.36––
PMIC_VSF0.34––
PMIC_VSG0.48––
PMIC_VTT_CTRL0.37––
PP0V6_S3_MEM_VREFDQ_A0.76––
PP0V9_TBT_X_CIO0.37––
PP0V9_TBT_X_DP0.30––
PP0V9_TBT_X_LVR0.27––
PP0V9_TBT_X_PCIE0.30––
PP0V9_TBT_X_SVR0.2600.900–
PP0V9_TBT_X_USB0.37––
PP0V675_CAM_VREF0.59––
PP0V675_MEM_CAM_VREFCA0.54––
PP0V675_MEM_CAM_VREFDQ0.59––
PP1V_OPC_S00.151.055–
PP1V_S0G0.21––
PP1V_S0SW_PCHCLKOL––
PP1V_S30.230.997–
PP1V_S5_PCH_DCPDSW0.34––
PP1V_S5G0.1001.000–
PP1V_S5G_PCHCLK0.11––
PP1V_S5G_REG0.0441.00045.00R
PP1V_S5GTD0.1101.000–
PP1V_SUS_PCH_VCCCLK2_F0.1001.000–
PP1V_SUS_PCH_VCCCLK4_F0.1001.000–
PP1V_SUS_PCH_VCCCLK5_F0.1001.000–
PP1V_SUSRS0SW_PCHCLK0.04–46.69R
PP1V_SUSSW_PCH_VCCAMPHYPLL_F0.1101.000–
PP1V1_UPC_XA_LDO_BMC0.51––
PP1V1_UPC_XB_LDO_BMC0.51––
PP1V2_CAM0.301.200–
PP1V2_CAM_PCIE_PVDD_FLT0.35––
PP1V2_CAM_PCIE_VDD_FLT0.35––
PP1V2_CAM_XTALPCIEVDD0.35––
PP1V2_S0G0.201.200–
PP1V2_S30.1971.200–
PP1V2_S3_REG0.2001.200–
PP1V2_S5_SMC_VDDC0.52––
PP1V8_CAM0.50––
PP1V8_S00.34––
PP1V8_S30.28––
PP1V8_S5G0.3321.800–
PP1V8_SUS_PCH_VCC1P8OL––
PP1V8_UPC_XA_LDOA0.52––
PP1V8_UPC_XA_LDOD0.481.800–
PP1V8_UPC_XB_LDOA0.52––
PP1V8_UPC_XB_LDOD0.481.800–
PP1V25_VREF0.46––
PP1V35_CAM0.2701.350–
PP1V35_DDR_CLK0.30––
PP2V9_SYSCLK0.46––
PP3V0_S5_AVREF_SMC0.60––
PP3V1_RTC0.443.000–
PP3V3_G3H0.363.300–
PP3V3_G3H_UPC_XA0.353.300–
PP3V3_G3H_UPC_XB0.363.300–
PP3V3_G3H_VR0.353.300–
PP3V3_LDO3V0.40––
PP3V3_S00.3603.300–
PP3V3_S0_CPUTHMSNS_R0.40––
PP3V3_S0SW_LCD0.512––
PP3V3_S0SW_LCD_R0.56––
PP3V3_S0SW_LCD_R10.56––
PP3V3_S40.47––
PP3V3_S4_WLS0.47––
PP3V3_S50.3803.300–
PP3V3_S5_S0R0.390––
PP3V3_S5_SSD_SNS0.3803.300–
PP3V3_S5_TBT_X_SW0.46––
PP3V3_S5G0.343.300–
PP3V3_SSD_FLT0.383.300–
PP3V3_TBT_X_ANA_PCIE0.50––
PP3V3_TBT_X_ANA_USB20.47––
PP3V3_TBT_X_F0.363.300–
PP3V3_TBT_X_LC0.52––
PP3V3_TBT_X_S00.363.300–
PP3V3_UPC_XA_LDO0.503.300–
PP3V3_UPC_XB_LDO0.503.300–
PP5V_LDO5V0.44––
PP5V_S00.45––
PP5V_S0_ALSCAM_F0.417––
PP5V_S0_BKLT_A0.417––
PP5V_S0_BKLT_D0.419––
PP5V_S0_P1VOPC0.45––
PP5V_S0SW_LCD0.512––
PP5V_S40.4205.000–
PP5V_S4_TPAD_CONN0.44––
PP5V_S50.435.000–
PP5VR7V_VPROGOTP0.44––
PP20V_USBC_XA_VBUS0.1420.000–
PP20V_USBC_XA_VBUS_CONN0.1520.000–
PP20V_USBC_XA_VBUS_F0.1420.000–
PP20V_USBC_XB_VBUS0.1420.000–
PP20V_USBC_XB_VBUS_CONN0.1520.000–
PP20V_USBC_XB_VBUS_F0.14020.000–
PPBUS_G3H0.45013.100–
PPBUS_G3H_CPU0.46013.100–
PPBUS_G3H_P3V3S50.45013.100–
PPBUS_G3H_P5VS40.4513.100–
PPBUS_G3H_R0.37––
PPBUS_G3H_SPKRL0.45013.100–
PPBUS_G3H_SSD0.46––
PPBUS_G3H_TPAD0.45013.100–
PPBUS_PMIC0.44––
PPBUS_SSD_FLT0.44––
PPDCIN_G3H0.5620.000–
PPDCIN_G3H_CHGR0.5620.000–
PPDCIN_G3H_CHGR_R0.56––
PPDCIN_G3H_VSNS_IN0.56––
PPDCPRTC_PCH0.69––
PPVBAT_G3H_CHGR_R0.45013.100–
PPVBAT_G3H_CHGR_REG0.45013.100–
PPVBAT_G3H_CONN0.6313.100–
PPVCCCPU_S0G0.0051.8005.800R
PPVCCCPU_S0G_PH10.0051.8005.800R
PPVCCCPU_S0G_PH20.0051.8005.800R
PPVCCGT_S0G0.0041.8002.480R
PPVCCGT_S0G_PH10.0041.8002.48R
PPVCCGT_S0G_PH20.0041.8002.480R
PPVCCGT_S0G_PH30.0041.8002.480R
PPVCCIO_S0G0.050.950–
PPVCCOPC_S0G0.07––
PPVCCPCH_S5G0.1501.00085.000R
PPVCCSA_S0G0.0081.5009.600R
PPVCCSA_S0G_R0.0081.5009.600R
PPVIN_G3H_P3V3G3H0.55––
PPVIN_S0SW_LCDBKLT0.810.86012.900–
PPVIN_S0SW_LCDBKLT_F0.45013.100–
PPVIN_S0SW_LCDBKLT_R0.320.45013.100–
PPVIN_S4_TPAD_FUSE0.45013.100–
PPVIN_SW_LCDBKLT_SW0.81012.900–
PPVIOE_CAMCLK0.35––
PPVOUT_S0_LCDBKLT1.1401.15055.000–
PPVTT_S00.150.599–
PROCHOT_LEDOL––
PROCHOT_LED_LOL––
PROG10.552––
PROG20.552––
PROG30.487––
PROG40.557––
PROG50.557––
PSYS0.551––
PU_PCH_RCIN_L0.58––
PU_SOC_UART_D2R0.56––
PU_SSD_UART_D2R0.56––
PU_SSD_UART_R2D0.56––
PU_TBT_T_PLUG_EVENT_L0.78––
RF_0_ANTOL––
RF_1_ANTOL––
RTC_RESET_L0.82––
S5_PWRGD0.48––
SAVE_CC1A_BOL––
SAVE_CC1A_G0.80––
SAVE_CC1A_ZOL––
SAVE_CC1B_BOL––
SAVE_CC1B_G0.79––
SAVE_CC1B_ZOL––
SAVE_CC2A_BOL––
SAVE_CC2A_G0.81––
SAVE_CC2A_ZOL––
SAVE_CC2B_BOL––
SAVE_CC2B_G0.78––
SAVE_CC2B_ZOL––
SAVR_BOOT0.60––
SAVR_COMP0.559––
SAVR_COMP_LOL––
SAVR_FB0.5––
SAVR_FB_L_11.17––
SAVR_FB_L_2OL––
SAVR_FB_L_30.01––
SAVR_FCCM0.547––
SAVR_IMON0.558––
SAVR_ISNS_IOUTOL––
SAVR_ISNS_NOL––
SAVR_ISNS_POL––
SAVR_ISNSR_N0.0081.5009.600R
SAVR_ISNSR_P0.0081.5009.600R
SAVR_ISUM_N0.01––
SAVR_ISUM_P0.336––
SAVR_ISUMN_R0.153––
SAVR_PHASE0.00––
SAVR_PWM0.547––
SAVR_RTN0.00–2.30r
SAVR_SW0.0081.5009.600R
SCLK0.182––
SDA0.169––
SMB_PMIC_SCL0.41––
SMB_PMIC_SDA0.42––
SMBUS_PCH_CLK0.76––
SMBUS_PCH_DATA0.76––
SMBUS_SMC_0_S0_SCL0.73––
SMBUS_SMC_0_S0_SDA0.73––
SMBUS_SMC_1_S0_SCL0.60––
SMBUS_SMC_1_S0_SDA0.59––
SMBUS_SMC_3_S0_SCL0.73––
SMBUS_SMC_3_S0_SDA0.73––
SMBUS_SMC_4_G3_SCL0.70––
SMBUS_SMC_4_G3_SDA0.70––
SMBUS_SMC_5_G3H_SCL0.42––
SMBUS_SMC_5_G3H_SDA0.42––
SMC_1V2S3_ISENSE0.74––
SMC_1VS5G_ISENSE0.76––
SMC_3V3LCD_ISENSE0.74––
SMC_3V3S5_ISENSE0.74––
SMC_3V3SSD_ISENSE0.74––
SMC_3V3WLS_ISENSE0.74––
SMC_5VS4_ISENSE0.75––
SMC_AUX_OK0.60––
SMC_BC_ACOK0.613.400–
SMC_BMON_ISENSE0.74––
SMC_BT_PWR_EN0.483.300–
SMC_CHGR_INT_L0.603.300–
SMC_CLK12M_EN0.45––
SMC_CLK32K0.58––
SMC_CPU_HI_ISENSE0.73––
SMC_CPU_IMON_ISENSE0.74––
SMC_CPU_ISENSE0.74––
SMC_CPU_VSENSE0.73––
SMC_DCIN_ISENSE0.74––
SMC_DCIN_VSENSE0.74––
SMC_DEBUGPRT_RX_L0.71––
SMC_DEBUGPRT_TX_L0.71––
SMC_DELAYED_PWRGD0.74––
SMC_DEV_SUPPLY_L1.56––
SMC_DEV_SUPPLY_R_L0.74––
SMC_DP_HPD_L0.74––
SMC_FAN_0_CTL0.75––
SMC_FAN_0_TACH0.75––
SMC_GT_ISENSE0.74––
SMC_GT_VSENSE0.73––
SMC_LCDBKLT_ISENSE0.74––
SMC_LID_LEFT0.52––
SMC_LID_LEFT_R0.52––
SMC_LID_RIGHT0.49––
SMC_LRESET_L0.41––
SMC_LSOC_RST0.63––
SMC_MPM_OK0.61––
SMC_ONOFF_L0.743.300–
SMC_ONOFF_R_LOL––
SMC_OOB1_D2R_L0.76––
SMC_OOB1_R2D_L0.76––
SMC_PBUS_VSENSE0.73––
SMC_PCH_SUSACK_L0.73––
SMC_PCH_SUSWARN_L0.73––
SMC_PECI_L0.73––
SMC_PM_G2_EN0.51––
SMC_PME_S4_DARK_L0.42––
SMC_PME_S4_WAKE_L0.74––
SMC_PMIC_INT_L0.46––
SMC_PROCHOT0.74––
SMC_PROCHOT_L0.52––
SMC_RESET_L0.623.400–
SMC_RESET_R_L0.603.400–
SMC_RST_BTN_LOL––
SMC_RST_BTN_R_LOL––
SMC_RST_IN0.61––
SMC_RUNTIME_SCI_L0.60––
SMC_RX_L0.74––
SMC_SA_IMON_ISENSE0.74––
SMC_SA_ISENSE0.74––
SMC_SENSOR_ALERT_L0.70––
SMC_SENSOR_PWR_EN0.74––
SMC_TCK0.58––
SMC_TCON_BKLT_PWM0.75––
SMC_TDI0.74––
SMC_TDO0.74––
SMC_THRMTRIP0.74––
SMC_THRMTRIP_L0.38––
SMC_TMS0.58––
SMC_TOPBLK_SWP_L0.71––
SMC_TPAD_ISENSE0.74––
SMC_TX_L0.74––
SMC_USBC_INT_L0.68––
SMC_VCCIO_CPU_DIV20.74––
SMC_VIBE_L0.74––
SMC_WAKE_L0.74––
SMC_WIFI_EVENT_L0.640.000–
SMC_WIFI_PWR_EN0.453.300–
SML_PCH_0_CLK0.79––
SML_PCH_0_DATA0.78––
SPI_ALT_CLK0.61––
SPI_ALT_CS_L0.61––
SPI_ALT_IO<2>0.54––
SPI_ALT_IO<3>0.54––
SPI_ALT_MISO0.54––
SPI_ALT_MOSI0.55––
SPI_CLK_R0.57––
SPI_CS0_R_L0.69––
SPI_DESCRIPTOR_OVERRIDE1.56––
SPI_DESCRIPTOR_OVERRIDE_L0.74––
SPI_IO<2>0.72––
SPI_IO<3>0.73––
SPI_IO2_STRAP_LOL––
SPI_MISO0.73––
SPI_MLB_CLK0.57––
SPI_MLB_CS_L0.68––
SPI_MLB_IO<2>0.70––
SPI_MLB_IO<3>0.72––
SPI_MLB_MISO0.71––
SPI_MLB_MOSI0.71––
SPI_MLBROM_CS_L0.64––
SPI_MOSI_R0.73––
SPIROM_USE_MLB0.70––
SPKRAMP_5V_10.56––
SPKRAMP_5V_20.55––
SPKRAMP_5V_30.55––
SPKRAMP_5V_40.55––
SPKRAMP_BSTN_20.612––
SPKRAMP_BSTN_30.59––
SPKRAMP_BSTN_40.59––
SPKRAMP_BSTP_10.59––
SPKRAMP_BSTP_20.606––
SPKRAMP_BSTP_30.59––
SPKRAMP_BSTP_40.604––
SPKRAMP_FL_OUT_N0.530––
SPKRAMP_FL_OUT_P0.53––
SPKRAMP_FR_OUT_N0.590––
SPKRAMP_FR_OUT_P0.530––
SPKRAMP_RL_OUT_N0.530––
SPKRAMP_RL_OUT_P0.530––
SPKRAMP_RR_OUT_N0.590––
SPKRAMP_RR_OUT_P0.530––
SPKRCONN_FL_OUT_N0.530––
SPKRCONN_FL_OUT_P0.530––
SPKRCONN_FR_OUT_N0.590––
SPKRCONN_FR_OUT_P0.530––
SPKRCONN_RL_OUT_N0.530––
SPKRCONN_RL_OUT_P0.530––
SPKRCONN_RR_OUT_N0.590––
SPKRCONN_RR_OUT_P0.530––
SSD_BOOT_CONN_L0.78––
SSD_BOOT_L0.78––
SSD_CLKREQ_L1.52––
SSD_ENOL––
SSD_JTAG_TCK0.77––
SSD_JTAG_TMS0.77––
SSD_PWR_EN_CONN_L0.63––
SSD_PWR_EN_L0.63––
SSD_PWR_REQ0.53––
SSD_RESET_L0.78––
SSD_SR_EN_L0.56––
SWOPC_CNFG0.58––
SYS_DETECT_LOL––
SYSCLK_CLK12M_SMC0.45––
SYSCLK_CLK24M_CAMERA0.45––
SYSCLK_CLK24M_PCH0.43––
SYSCLK_CLK24M_X10.45––
SYSCLK_CLK24M_X20.46––
SYSCLK_CLK24M_X2_R0.46––
SYSCLK_CLK32K_BT_AP0.490.000–
SYSCLK_CLK32K_BT_AP_R0.450.000–
SYSCLK_CLK32K_PCH0.47––
SYSRST_R_LOL––
TBA_AUX_DET0.61––
TBA_BGATE0.62––
TBA_BOOT10.58––
TBA_BOOT1_RC0.59––
TBA_BOOT20.58––
TBA_BOOT2_RC0.58––
TBA_COMP0.61––
TBA_CSI_N0.56020.000–
TBA_CSI_P0.56020.000–
TBA_CSIR_N0.56–2.600R
TBA_CSIR_P0.56–2.600R
TBA_CSO_N0.45013.100–
TBA_CSO_P0.45013.100–
TBA_CSOR_N0.3713.1002.400R
TBA_CSOR_P0.3713.1002.400R
TBA_GATE_Q10.86––
TBA_GATE_Q20.46––
TBA_GATE_Q40.83––
TBA_HPWR_EN_L0.613.300–
TBA_LX10.41––
TBA_LX20.41––
TBA_PHASE10.42013.100–
TBA_PHASE20.42013.100–
TBA_VDDA0.44––
TBA_VDDP0.44––
TBT_POC_RESET0.72––
TBT_X_CIO_PLUG_EVENT_L0.58––
TBT_X_CIO_PWR_EN0.55––
TBT_X_CLKREQ_L0.59––
TBT_X_PCI_RESET_L0.57––
TBT_X_PCIE_BIAS0.78––
TBT_X_RBIAS0.78––
TBT_X_ROM_HOLD_L0.71––
TBT_X_ROM_WP_L0.60––
TBT_X_RSENSE0.00––
TBT_X_SPI_CLK0.57––
TBT_X_SPI_CLK_DBG0.67––
TBT_X_SPI_CS_L0.59––
TBT_X_SPI_MISO0.59––
TBT_X_SPI_MOSI0.60––
TBT_X_TEST_EN0.10––
TBT_X_THERM_D_N0.00––
TBT_X_THERM_D_POL––
TBT_X_USB_PWR_EN0.54––
TBT_XA_USB2_RBIAS0.42––
TBT_XB_USB2_RBIAS0.42––
TBTXPOCRST_CT0.73––
TBTXPOCRST_SNS1.38––
TCON_BKLT_PWM0.7––
TP_CAM_JTAG_TCK0.77––
TP_CAM_JTAG_TDI0.77––
TP_CAM_JTAG_TDO0.77––
TP_CAM_JTAG_TMS0.77––
TP_CAM_JTAG_TRST_L0.77––
TP_CAM_LV_JTAG_TCK0.77––
TP_CAM_LV_JTAG_TDI0.77––
TP_CAM_LV_JTAG_TDO0.77––
TP_CAM_LV_JTAG_TMS0.77––
TP_CAM_LV_JTAG_TRSTN0.77––
TP_CAM_PCIE_WAKE_L0.52––
TP_CAM_RAMCFG00.77––
TP_CAM_RAMCFG10.77––
TP_CAM_RAMCFG20.77––
TP_CAM_TEST_MODE00.77––
TP_CAM_TEST_MODE10.77––
TP_CAM_TEST_MODE20.77––
TP_CAM_UARTRTS0.77––
TP_CAM_UARTTXD0.77––
TP_CPU_PWRGD0.42––
TP_CPUVR_GH2OL––
TP_CPUVR_GL10.43––
TP_CPUVR_GL20.44––
TP_GTVR_GH1OL––
TP_GTVR_GH2OL––
TP_GTVR_GH3OL––
TP_GTVR_GL10.45––
TP_GTVR_GL20.45––
TP_GTVR_GL30.44––
TP_ISNS_3V3S0NOL––
TP_ISNS_3V3S0POL––
TP_ISNS_SKPRLN0.45013.100–
TP_ISNS_SKPRLP0.4513.100–
TP_JTAG_WLAN_TCK0.79––
TP_JTAG_WLAN_TDO0.75––
TP_JTAG_WLAN_TMS0.79––
TP_JTAG_WLAN_TRST0.79––
TP_PCH_SLP_A_L0.56––
TP_SAVR_GHOL––
TP_SAVR_GL0.45––
TP_SPKR_ID10.56––
TP_UPC_XA_DBG_UART_RX0.77––
TP_UPC_XA_DBG_UART_TX0.77––
TP_UPC_XB_DBG_UART_RX0.77––
TP_UPC_XB_DBG_UART_TX0.77––
TP_USBC_XA_RESET_L0.78––
TP_WLAN_UART_R2D0.75––
TPAD_SPI_CLK0.53––
TPAD_SPI_CS_CONN_L0.71––
TPAD_SPI_CS_L0.52––
TPAD_SPI_IF_EN0.56––
TPAD_SPI_INT_L0.56––
TPAD_SPI_MISO0.60––
TPAD_SPI_MOSI0.63––
TPAD_VIBE_L0.75––
TSNS_1_A0OL––
TSNS_1_A1OL––
TSNS_1_NOL––
TSNS_1_POL––
TSNS_2_A0OL––
TSNS_2_A1OL––
TSNS_3_N0.64––
TSNS_3_P0.64––
TSP_UPC_XB_SWD_CLK0.74––
UPC_XA_BUSPOWERZ0.00––
UPC_XA_DBG30.76––
UPC_XA_DBG40.77––
UPC_XA_FAULT_L0.75––
UPC_XA_GATE10.65––
UPC_XA_GATE20.64––
UPC_XA_I2C_ADDR0.00––
UPC_XA_R_OSC0.52––
UPC_XA_SS0.53––
UPC_XA_UART_RX0.74––
UPC_XA_UART_TX0.75––
UPC_XB_BUSPOWERZ0.00––
UPC_XB_FAULT_L0.75––
UPC_XB_GATE10.65––
UPC_XB_GATE20.64––
UPC_XB_R_OSC0.52––
UPC_XB_SPI_CLK0.57––
UPC_XB_SPI_CS_L0.59––
UPC_XB_SPI_MISO0.59––
UPC_XB_SPI_MOSI0.60––
UPC_XB_SS0.52––
USB_TESTER_N0.56––
USB_TESTER_P0.56––
USB_UPC_PCH_XA_N0.57––
USB_UPC_PCH_XA_P0.57––
USB_UPC_PCH_XB_N0.55––
USB_UPC_PCH_XB_P0.55––
USB_UPC_XA_F_N0.56––
USB_UPC_XA_F_P0.57––
USB_UPC_XB_F_N0.60––
USB_UPC_XB_F_P0.60––
USB3_EXTA_R2D_N0.58––
USB3_EXTA_R2D_P0.58––
USBC_X_RESET_L0.50––
USBC_X_RESET_L_R0.53––
USBC_XA_CC10.60––
USBC_XA_CC1_CONN0.71––
USBC_XA_CC20.60––
USBC_XA_CC2_CONN0.725––
USBC_XA_D2R_CONN_N<1>0.35––
USBC_XA_D2R_CONN_P<1>0.35––
USBC_XA_R2D_N<2>OL––
USBC_XA_R2D_P<2>OL––
USBC_XA_RPD_G10.59––
USBC_XA_RPD_G20.60––
USBC_XA_SBU10.88––
USBC_XA_SBU20.83––
USBC_XB_CC10.59––
USBC_XB_CC1_CONN0.72––
USBC_XB_CC20.59––
USBC_XB_CC2_CONN0.71––
USBC_XB_D2R_CONN_N<1>0.35––
USBC_XB_D2R_CONN_P<1>0.35––
USBC_XB_R2D_N<2>OL––
USBC_XB_R2D_P<2>OL––
USBC_XB_RPD_G10.59––
USBC_XB_RPD_G20.59––
USBC_XB_SBU1OL––
USBC_XB_SBU2OL––
V3V3G3H_BIAS0.55––
V3V3G3H_BOOST0.60––
V3V3G3H_BST_R0.60––
V3V3G3H_FB0.59––
V3V3G3H_FB_R0.36––
V3V3G3H_FB_R21.21––
V3V3G3H_FB_XW0.35––
V3V3G3H_SW0.353.300–
VCINP_P5V_U74700.46––
VCINP_P5V_U75100.47––
VCINP_P5V_U75200.47––
VCINP_P5V_U75300.47––
VR_HOT_L0.278––
VR0V9_IND_TBT_X0.2600.900–
WA_P0V9TBTXLVR_Q1.26––
WLAN_ROM_CLK0.70––
WLAN_ROM_CS0.70––
WLAN_ROM_MISO0.68––
WLAN_ROM_MOSI0.70––
WLAN_ROM_ORG0.72––
XDP_CPU_PRDY_L0.28––
XDP_CPU_PREQ_L0.28––
XDP_CPU_PWRBTN_L0.59––
XDP_CPU_TCK0.05––
XDP_CPU_TDI0.25––
XDP_CPU_TDO0.22––
XDP_CPU_TMS0.25––
XDP_CPU_TRST_L0.29––
XDP_DBRESET_L0.72––
XDP_JTAG_ISP_TCK0.55––
XDP_JTAG_ISP_TDI0.54––
XDP_PCH_OBSDATA_A20.79––
XDP_PCH_OBSDATA_A30.79––
XDP_PCH_OBSDATA_B00.79––
XDP_PCH_OBSDATA_C10.79––
XDP_PCH_OBSDATA_C30.79––
XDP_PCH_OBSDATA_D00.80––
XDP_PCH_OBSDATA_D10.79––
XDP_PCH_OBSDATA_D20.79––
XDP_PCH_OBSDATA_D30.79––
XDP_PCH_OBSFN_C10.79––
XDP_PCH_TCK0.47––
XDP_PCH_TDI0.26––
XDP_PCH_TDO0.23––
XDP_PCH_TMS0.26––
XDP_PCH_TRST_L0.29––
XDP_PM_RSMRST_L1.293.300–
XDP_PRESENT_CPU1.29––
XDP_PRESENT_LOL––
XDP_USB_EXTA_OC_L0.75––
XDP_USB_EXTB_OC_L0.766––
XDP_USB_EXTC_OC_L0.79––
XDP_USB_EXTD_OC_L0.79––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-00840?

OpenBoardData's known-good values for PPBUS_G3H on the 820-00840: diode 0.450, voltage 13.100. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-00840?

OpenBoardData's known-good values for PP3V3_G3H on the 820-00840: diode 0.36, voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-00840?

OpenBoardData's known-good values for PP5V_S5 on the 820-00840: diode 0.43, voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-00840 board?

Open your own 820-00840 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License