Apple laptop board · OpenBoardData
820-3115 known-good readings
Known-good readings for the Apple laptop board 820-3115: 363 nets, including 62 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 62 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-3115.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 62 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 10
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V42_G3H | 0.35 | 3.400 | – |
AI: what PP3V42_G3H is and how to check itPP3V42_G3H is the always-on 3.42 V rail on the 820-3115, indicated by the G3H suffix in its name. Known-good readings from the archive are a diode value of 0.35 and 3.400 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.35 suggests a short or leaky load on the rail; a missing or low voltage points to the rail's source or an overload. No known-good resistance reading exists for this rail. | |||
PPBUS_G3H | 0.450 | 12.490 | – |
AI: what PPBUS_G3H is and how to check itPPBUS_G3H is the main bus rail on this 820-3115, and the "G3H" suffix indicates it's an always-on rail (from the name). The archive lists a known-good diode reading of 0.450 and a voltage of 12.490, with no condition noted, so treat these as a guide only.
No known-good resistance reading exists here, so compare against a matching rail on a known-good board if needed. | |||
PPDCIN_G3H | 2.865 | 16.350 | – |
AI: what PPDCIN_G3H is and how to check itPPDCIN_G3H is the always-on G3H input rail, judging from its name: it's the DC input that should be present whenever the adapter is connected. Known-good readings from the archive are a diode value of 2.865 and 16.350 V with power applied; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the adapter connected. A diode reading far below 2.865 suggests a short or leaky part on the rail; no voltage where 16.350 V is expected points back toward the adapter, input path or a protection circuit. No known-good resistance reading is recorded for this rail. | |||
PPDCIN_G3H_CHGR | 0.640 | 16.420 | – |
AI: what PPDCIN_G3H_CHGR is and how to check itPPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in its name indicates it is always-on, present whenever the charger is connected. In the readings archive its known-good values are a diode reading of 0.640 to ground and 16.420 V with power applied — treat these as a guide, since they come from community contributions and vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.640 usually points to a short or a leaky component on the rail; a voltage well below 16.420 V suggests the input path from the charger is not passing power properly. No known-good resistance reading is available for this rail. | |||
PPDCIN_G3H_INRUSH | – | 16.420 | – |
AI: what PPDCIN_G3H_INRUSH is and how to check itPPDCIN_G3H_INRUSH is the always-on input rail from the adapter, judging by the G3H part of its name (general naming convention, not confirmed for this board). The archive lists one known-good voltage of 16.420 V; there is no known-good diode or resistance reading for this net here.
| |||
PPVBAT_G3H_CHGR_R | 0.450 | – | – |
AI: what PPVBAT_G3H_CHGR_R is and how to check itPPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name marks it as an always-on rail, and CHGR ties it to the charging circuit (from the name). The archive lists one known-good diode reading of 0.450 to ground, with no condition noted. Check it with the board unpowered and battery disconnected, in diode mode from the rail to ground, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.450 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PPVBAT_G3H_CHGR_REG | 0.450 | 12.500 | – |
AI: what PPVBAT_G3H_CHGR_REG is and how to check itPPVBAT_G3H_CHGR_REG — reference note
| |||
PPVBAT_G3H_CONN | OL | – | – |
AI: what PPVBAT_G3H_CONN is and how to check itPPVBAT_G3H_CONN is the battery connector side of the always-on G3H rail, judging by its name; the "G3H" suffix usually marks a supply that should be present whenever the battery or adapter feeds the board (general naming convention, not from this board's data). The only known-good reading recorded here is a diode value of OL to ground, with no condition noted, so treat it as a guide. Check it with the board unpowered in diode mode from the net to ground, then measure its voltage with power applied. No known-good voltage reading exists here, so compare against a matching net or a known-good board. A diode reading far from OL to ground usually points to a short or a low-resistance path on that net, but confirm with a second measurement before suspecting any part. | |||
PPVIN_G3H_P3V42G3H | 0.570 | 15.950 | – |
AI: what PPVIN_G3H_P3V42G3H is and how to check itPPVIN_G3H_P3V42G3H is an always-on input rail feeding the P3V42G3H supply, judging by the G3H "always on" naming. The archive lists a known-good diode reading of 0.570 and a voltage of 15.950, with no condition noted, so treat these as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.570 suggests a short or leaky load on the rail; a voltage well off 15.950 points to a problem upstream in the input path. No known-good resistance reading is listed here. | |||
PPVRTC_G3H | 0.444 | 3.300 | – |
AI: what PPVRTC_G3H is and how to check it
| |||
S5 and SUS: standby 10
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S5_SMC_VDDC | – | 1.200 | – |
AI: what PP1V2_S5_SMC_VDDC is and how to check it
| |||
PP1V05_SUS | 0.48 | – | – |
AI: what PP1V05_SUS is and how to check it
| |||
PP3V3_S5 | 0.49 | 3.300 | – |
AI: what PP3V3_S5 is and how to check itPP3V3_S5 is the 3.3 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage (from the name, not from a schematic). Known-good readings in the archive: diode 0.49 to ground and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.49 usually points to a short or a leaky part on that rail; a voltage far from 3.300 V points to the standby supply not coming up. No known-good resistance reading is recorded for this rail. | |||
PP3V3_S5_AVREF_SMC | – | 3.200 | – |
AI: what PP3V3_S5_AVREF_SMC is and how to check itPP3V3_S5_AVREF_SMC is a 3.3 V standby rail; the S5 and SUS parts of the name indicate it belongs to the standby stage, and AVREF_SMC suggests it is a reference supply for the SMC. The archive lists a known-good voltage of 3.200 V, with no condition noted. Check it unpowered in diode mode to ground first, then power the board and measure the voltage; no known-good diode or resistance reading is recorded here, so compare against a matching 3.3 V standby rail or a known-good board. A voltage well below 3.200 V points to a problem upstream on the standby supply or a heavy load on the rail, but that is a likely cause, not a confirmed one. | |||
PP3V3_SUS | 0.34 | 3.300 | – |
AI: what PP3V3_SUS is and how to check itPP3V3_SUS is the 3.3 V standby rail; the SUS in the name indicates it is present in standby, before the board fully powers on. The archive lists a known-good diode reading of 0.34 to ground and 3.300 V with power applied; these are community readings and only a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.34 suggests a short or leak on the rail, while a missing or low 3.300 V points to the standby supply or its enable; no known-good resistance value is listed here. | |||
PP5V_S5 | 0.52 | 5.00 | – |
AI: what PP5V_S5 is and how to check itPP5V_S5 is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage (from the name). The archive lists a known-good diode reading of 0.52 to ground and 5.00 V with power applied; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from PP5V_S5 to ground, then power up and measure the voltage. A diode value far below 0.52 suggests a short or leaky load on the rail; a missing or low 5.00 V points to the standby supply or its enable, not necessarily the rail itself. No known-good resistance reading is available here. | |||
PP5V_S5_P18V5S5_VIN | – | 5.000 | – |
AI: what PP5V_S5_P18V5S5_VIN is and how to check it
| |||
PP5V_SUS | – | 5.000 | – |
AI: what PP5V_SUS is and how to check itPP5V_SUS is the 5 V suspend (standby) rail; the "SUS" and S5 in its name indicate it belongs to the standby stage, before the main rails come up. The archive lists one known-good reading: 5.000 V, with no condition noted, so treat it as a guide only. To check it, power the board off and measure diode mode from PP5V_SUS to ground, then apply power and measure the voltage on the rail. There is no known-good diode reading here, so compare against a matching net or a known-good board. A voltage far from 5.000 V usually points to a problem in the standby supply or a heavy load pulling the rail down, but that's a likely cause, not a confirmed one. | |||
PPBUS_S5_HS_COMPUTING_ISNS | 0.050 | 12.490 | 0.000R |
AI: what PPBUS_S5_HS_COMPUTING_ISNS is and how to check itPPBUS_S5_HS_COMPUTING_ISNS is a current-sense line on the main battery/charger bus (PPBUS), in the S5 standby state, judging from its name. Archived readings for this rail are diode 0.050, voltage 12.490 V and resistance 0.000R; treat these as a guide only, since they come from community contributions and vary with board state. Check it unpowered in diode mode to ground, then measure the voltage with power applied. A reading far from these usually points to a short or open on the bus or its sense path, but one reading alone doesn't confirm a bad part; no known-good value of another kind is listed here. | |||
PPBUS_S5_HS_OTHER_ISNS | 0.45 | 12.490 | – |
AI: what PPBUS_S5_HS_OTHER_ISNS is and how to check itPPBUS_S5_HS_OTHER_ISNS (820-3115) — reference note
| |||
S4 1
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S4 | – | 3.300 | – |
AI: what PP3V3_S4 is and how to check itPP3V3_S4 is a 3.3 V rail in the S4 startup stage, as the name indicates. The only known-good reading here is 3.300 V; no diode or resistance value is recorded for this rail.
| |||
S3: memory 9
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V5_S3 | 0.127 | 1.500 | 126.000 |
AI: what PP1V5_S3 is and how to check itPP1V5_S3 is a 1.5 V rail; the "S3" in its name indicates it belongs to the memory (S3) power state, and that meaning comes from the rail name, not from board data. Known-good readings in the archive: diode 0.127, voltage 1.500 V, resistance 126.000 (no condition noted). Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode or resistance far below known-good usually points to a short or a failing load on the rail; far above can mean an open path. No known-good current draw is listed here, and these are community readings, so treat them as a guide. | |||
PP1V5_S3_DDR | 0.127 | 1.500 | 126.000 |
AI: what PP1V5_S3_DDR is and how to check itPP1V5_S3_DDR is a 1.5 V memory rail; the "S3" and "DDR" parts of the name indicate it belongs to the memory power state, though that's from the name rather than a board file.
| |||
PP1V5_S3RS0 | 0.100 | – | 100.000R |
AI: what PP1V5_S3RS0 is and how to check itPP1V5_S3RS0 is a 1.5 V rail in the S3 (memory) startup stage, judging from its name; the board data doesn't list which parts sit on it. Known-good readings here are diode 0.100 and resistance 100.000R, community values that vary with board state. Check it unpowered in diode mode to ground, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode reading far from 0.100 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault. | |||
PP3V3_S3 | – | 3.300 | – |
AI: what PP3V3_S3 is and how to check itPP3V3_S3 is the 3.3 V rail that, from its S3 suffix, belongs to the memory (S3) power state on this 820-3115. The readings archive lists a known-good voltage of 3.300 V for it; there is no known-good diode or resistance value here.
| |||
PP3V3_S3RS4_BT_F | 0.395 | 3.300 | – |
AI: what PP3V3_S3RS4_BT_F is and how to check it
| |||
PP5V_S3 | 0.43 | 5.000 | – |
AI: what PP5V_S3 is and how to check itPP5V_S3 is the 5 V rail that, from its name, belongs to the S3 (memory) startup stage. Known-good readings here are a diode value of 0.43 and 5.000 V; no condition is recorded for either, so treat them as a guide only.
| |||
PP5V_S3_IR_R | 0.42 | – | – |
AI: what PP5V_S3_IR_R is and how to check itPP5V_S3_IR_R is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state; the IR_R suffix isn't explained by the name alone. The only known-good reading here is a diode value of 0.42 on this net, with no condition recorded; there is no known-good voltage or resistance reading for it. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.42 usually points to a short or a leaky load on the rail, while a much higher reading can mean an open path; confirm with a voltage check before suspecting any part. | |||
PP5V_S3_USB_A_F | 0.518 | – | – |
AI: what PP5V_S3_USB_A_F is and how to check itPP5V_S3_USB_A_F is a 5 V rail for USB-A power that, from its name, comes up in the S3 (memory/suspend) stage. The only known-good reading here is a diode value of 0.518 to ground; no voltage reading is listed. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.518 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken path. Voltage behaviour is not documented here, so compare against a known-good board of the same model. | |||
PPVTTDDR_S3 | 0.49 | – | – |
AI: what PPVTTDDR_S3 is and how to check itPPVTTDDR_S3 is a memory-stage (S3) rail; the DDR/VTT part of the name suggests it's the termination voltage for the DDR memory, though that's from the name rather than confirmed circuit data. The only known-good reading here is a diode value of 0.49 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.49 usually points to a short or a leaky component on the rail, but one reading isn't proof a part is bad, so compare against a matching rail or a known-good board before replacing anything. | |||
S0: running 32
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP0V75_S0_DDRVTT | 0.45 | – | – |
AI: what PP0V75_S0_DDRVTT is and how to check itPP0V75_S0_DDRVTT is a 0.75 V rail; the "S0" in the name indicates it is active in the running state, and "DDRVTT" indicates it is the DDR termination rail. The only known-good reading here is a diode value of 0.45 to ground, with no condition recorded; no known-good voltage reading is available. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.45 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part; compare with a matching rail or a known-good board before replacing anything. | |||
PP1V05_S0 | 0.013 | 1.054 | 0.000R |
AI: what PP1V05_S0 is and how to check itPP1V05_S0 is the 1.05 V rail that stays on in the S0 running state, judged from its name; the board data doesn't identify which parts sit on it. Known-good readings here are diode 0.013, voltage 1.054 and resistance 0.000R, all community values and only a guide. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.013 suggests a short or leak on the rail; a missing or wrong voltage points to the supply that makes it or its enable. No known-good value exists for other conditions, so compare against a matching rail or a known-good board. | |||
PP1V5_S0 | 0.29 | – | – |
AI: what PP1V5_S0 is and how to check itPP1V5_S0 is a 1.5 V rail; the S0 suffix, from its name, means it belongs to the running (S0) power state, so it should be present once the board is fully on. The only known-good reading here is a diode value of 0.29 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.29 suggests a short or a leaky load on the rail; far above it suggests an open path. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. | |||
PP1V05_S0_PCH | 0.012 | – | 12.500R |
AI: what PP1V05_S0_PCH is and how to check itPP1V05_S0_PCH is a 1.05 V rail for the PCH, from its name, and the S0 suffix indicates it belongs to the running state. The archive lists a known-good diode reading of 0.012 and a resistance of 12.500R for this net; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied. A reading far from these values usually points to a short or a faulty load on the rail, but no known-good voltage reading exists here, so compare against a matching rail or a known-good board before condemning a part. | |||
PP1V05_S0_PCH_VCCADPLL | 0.15 | – | – |
AI: what PP1V05_S0_PCH_VCCADPLL is and how to check itPP1V05_S0_PCH_VCCADPLL is a 1.05 V rail feeding the PCH's VCCADPLL supply; the S0 suffix from its name means it belongs to the running (S0) state, so it should come up once the board is powered on. The only known-good reading in the archive is a diode value of 0.15 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.15 usually points to a short or a leaky part on that rail, but a single reading isn't proof a part is bad; no known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. | |||
PP1V05_S0_PCH_VCCCLKDMI_R | 0.012 | – | 12.500R |
AI: what PP1V05_S0_PCH_VCCCLKDMI_R is and how to check it
| |||
PP1V8_S0 | 0.120 | – | – |
AI: what PP1V8_S0 is and how to check itPP1V8_S0 is a 1.8 V rail; the S0 suffix, from its name, marks it as a running-state supply. The archive's only known-good figure is a diode reading of 0.120 to ground, with no condition recorded and no known-good voltage here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.120 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PP1V8_S0_CPU_VCCPLL_R | 0.110 | – | 110.000R |
AI: what PP1V8_S0_CPU_VCCPLL_R is and how to check itPP1V8_S0_CPU_VCCPLL_R is a 1.8 V rail feeding the CPU's PLL supply; the "S0" in the name indicates it belongs to the running (S0) state, and that reading is from the name, not from a schematic. Known-good from the archive: diode 0.110 and resistance 110.000R, with no condition noted. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode or resistance far from those values usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. No known-good voltage reading is available here. | |||
PP1V8_S0_PCH_VCCTX_LVDS_F | 0.120 | – | – |
AI: what PP1V8_S0_PCH_VCCTX_LVDS_F is and how to check itPP1V8_S0_PCH_VCCTX_LVDS_F is a 1.8 V rail; from its name it supplies the PCH's LVDS transmit side and is up in the S0 (running) state. The archive lists a diode reading of 0.120 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far from 0.120 suggests a short or leaky part on the rail, but a single reading isn't proof — compare against a matching net or a known-good board before replacing anything. | |||
PP3V3_S0 | 0.339 | – | – |
AI: what PP3V3_S0 is and how to check itPP3V3_S0 is the 3.3 V rail for the S0 (running) state, judging by its name: it should be up once the board is fully powered on. The archive lists one known-good diode reading of 0.339 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.339 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board. | |||
PP3V3_S0_CPUTHMSNS_R | 0.39 | – | – |
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check itPP3V3_S0_CPUTHMSNS_R is a 3.3 V rail, from its name: the PP3V3 prefix is the supply, S0 means the running state, and CPUTHMSNS_R suggests a CPU thermal-sense return. The archive lists one known-good diode reading of 0.39 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the net, then measure the voltage with power applied in the running state. A diode reading far from 0.39 usually points to a short or a damaged part on that net, but a single reading isn't proof, so compare with a matching sense net or a known-good board before replacing anything. | |||
PP3V3_S0_LCD_F | 0.34 | – | – |
AI: what PP3V3_S0_LCD_F is and how to check itPP3V3_S0_LCD_F is a 3.3 V LCD rail that is on in the S0 (running) state, judging from its name. The only known-good reading here is a diode value of 0.34 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.34 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken connection. Confirm with a voltage measurement before suspecting any part. | |||
PP3V3_S0_PCH_VCC3_3_CLK_F | 0.350 | – | – |
AI: what PP3V3_S0_PCH_VCC3_3_CLK_F is and how to check itPP3V3_S0_PCH_VCC3_3_CLK_F is a 3.3 V rail feeding the PCH clock section, from its name; the S0 suffix means it belongs to the running state. The archive lists one known-good diode reading of 0.350 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode to ground, then power the board and measure the voltage. A diode reading far from 0.350 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PP3V3_S0_PCH_VCC3_3_CLK_R | 0.350 | – | – |
AI: what PP3V3_S0_PCH_VCC3_3_CLK_R is and how to check itPP3V3_S0_PCH_VCC3_3_CLK_R is a 3.3 V rail, from its name: the S0 (running) state supply for the PCH's 3.3 V clock circuit. The only known-good reading here is a diode value of 0.350 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far from 0.350 usually points to a short or a damaged component on that rail, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything. | |||
PP5V_S0 | 0.37 | 5.000 | – |
AI: what PP5V_S0 is and how to check itPP5V_S0 is the 5 V rail that is present in the S0 (running) state, judging by its name. Known-good readings for this rail: diode 0.37 to ground and 5.000 V with power applied.
No known-good resistance reading is available for this rail. | |||
PP5V_S0_CPUIMVP_VCC | 0.38 | 5.000 | – |
AI: what PP5V_S0_CPUIMVP_VCC is and how to check itPP5V_S0_CPUIMVP_VCC is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds the CPU IMVP supply. Known-good readings in the archive: diode 0.38 to ground and 5.000 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far below 0.38 suggests a short or leaky load on the rail; a voltage well off 5.000 V points to the supply or its enable. No known-good resistance reading is listed here. | |||
PP5V_S0_CPUVCCIOS0_VCC | 0.38 | – | – |
AI: what PP5V_S0_CPUVCCIOS0_VCC is and how to check itPP5V_S0_CPUVCCIOS0_VCC is a 5 V rail that, from its name, supplies CPU VCCIO in the S0 (running) state. The only known-good figure here is a diode reading of 0.38 to ground, with no condition noted; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.38 usually points to a short or a damaged component on the rail, but a single reading isn't proof — confirm with a voltage check before replacing anything. | |||
PP5V_S0_HDD | – | 5.000 | – |
AI: what PP5V_S0_HDD is and how to check itPP5V_S0_HDD is the 5 V rail feeding the hard drive, and the S0 in its name marks it as a running-state rail (from the name). The archive lists one known-good voltage of 5.000 V, with no condition recorded; there is no known-good diode or resistance reading for this net.
| |||
PP5V_S0_HDD_FLT | 0.37 | 5.000 | – |
AI: what PP5V_S0_HDD_FLT is and how to check itPP5V_S0_HDD_FLT — the name indicates a 5 V rail (PP5V) that is present in the S0 running state and feeds the hard drive circuit (HDD), with FLT likely meaning a filtered or fault-sense line. That reading is from the name, not from a schematic. Known-good readings in the archive: diode 0.37 to ground and voltage 5.000 in the S0 running state. These are community readings and only a guide. To check it: power off and unplug, then measure diode mode from the rail to ground; power up into S0 and measure the voltage. A voltage well below 5 V in S0 points to a missing or loaded rail upstream, and a diode reading far from 0.37 suggests a short or an open on that net — but one reading alone doesn't confirm a bad part. No known-good resistance reading is recorded for this rail. | |||
PP5V_S0_VCCSAS0_VCC | 0.37 | – | – |
AI: what PP5V_S0_VCCSAS0_VCC is and how to check itPP5V_S0_VCCSAS0_VCC is a 5 V supply rail that, from its name, runs in the S0 (fully on) state and feeds the SAS/SATA section of the chipset. The archive lists one known-good diode reading of 0.37 to ground; there is no known-good voltage reading here, so treat 0.37 as a guide only. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power up and measure the voltage at the rail. A diode reading far from 0.37 suggests a short or leaky part on that net, while a correct diode reading with no 5 V present points upstream to the rail's source or its enable. | |||
PPBUS_S0_LCDBKLT_FUSED | 0.450 | – | – |
AI: what PPBUS_S0_LCDBKLT_FUSED is and how to check itPPBUS_S0_LCDBKLT_FUSED is the fused backlight boost rail for the LCD, from its name: PPBUS is the main adapter/battery bus, S0 means it's present in the running state, and LCDBKLT is the display backlight. The archive lists one known-good diode reading of 0.450 to ground, with no condition noted; there is no known-good voltage reading here.
| |||
PPCPUVCCIO_S0_REG_R | 0.013 | 1.000 | – |
AI: what PPCPUVCCIO_S0_REG_R is and how to check itPPCPUVCCIO_S0_REG_R is a CPU I/O supply rail; the S0 in its name indicates it belongs to the running state, and REG suggests a regulated rail. The archived readings give diode 0.013 and voltage 1.000, with no condition noted, so treat them as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode value far below 0.013 suggests a short or a leaky part on the rail; no known-good resistance reading is recorded here, so compare against a matching rail or a known-good board. | |||
PPVCCSA_S0_CPU | 0.053 | 0.800 | 52.000R |
AI: what PPVCCSA_S0_CPU is and how to check it
| |||
PPVCCSA_S0_REG_R | 0.053 | 0.807 | 52.000R |
AI: what PPVCCSA_S0_REG_R is and how to check itPPVCCSA_S0_REG_R is a running-state (S0, from the name) regulated supply rail, most likely feeding the CPU/system-agent domain — that part is general, not from this board's data. Known-good readings here: diode 0.053, voltage 0.807 V, resistance 52.000R. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered in S0. A diode reading far from 0.053 or a resistance far from 52.000R usually points to a short or a leaky load on the rail; a missing or wrong voltage points to the regulator or its enable. These are community readings and only a guide, and no known-good current draw is recorded here. | |||
PPVCORE_S0_AXG | 0.012 | – | – |
AI: what PPVCORE_S0_AXG is and how to check itPPVCORE_S0_AXG is the CPU core power rail; the "S0" in its name indicates it is active in the running state. The only archived reading is a diode value of 0.012 to ground, with no condition noted, so treat it as a guide rather than a firm spec. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.012 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. | |||
PPVCORE_S0_AXG_R | 0.012 | – | – |
AI: what PPVCORE_S0_AXG_R is and how to check itPPVCORE_S0_AXG_R is a core power rail; the "S0" in its name indicates it is a running-state rail, and "VCORE" points to processor core supply (from the name, not from a schematic). The archive lists one known-good reading: diode 0.012 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then measure its voltage with the board powered. A diode reading far from 0.012 usually points to a short or a leaky load on the rail, but a single reading doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything. | |||
PPVCORE_S0_AXG2_L | 0.012 | – | – |
AI: what PPVCORE_S0_AXG2_L is and how to check itPPVCORE_S0_AXG2_L is the CPU core power rail; the name indicates it's a running-state (S0) rail. The archive lists one known-good diode reading of 0.012 to ground, taken with the board unpowered; there is no known-good voltage reading here. Check it in diode mode to ground with power off, then measure the voltage with the board powered and running. A diode reading far from 0.012 usually points to a short or a leaky part on the rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
PPVCORE_S0_CPU | 0.010 | 1.100 | 9.600R |
AI: what PPVCORE_S0_CPU is and how to check itPPVCORE_S0_CPU is the CPU core power rail; the "S0" in its name indicates it is active in the running state. The archive lists known-good readings of diode 0.010, voltage 1.100 and resistance 9.600R, with no condition noted, so treat them as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.010 usually points to a short or a leaky part on the rail, but a small difference can be normal, so confirm with the voltage and resistance before replacing anything. No known-good value of any other kind is listed here. | |||
PPVCORE_S0_CPU_PH1 | 0.010 | 1.100 | – |
AI: what PPVCORE_S0_CPU_PH1 is and how to check itPPVCORE_S0_CPU_PH1 is the CPU core power rail (the S0 in the name indicates running state; PH1 likely a phase node). Known-good readings from the archive: diode 0.010 and voltage 1.100. Check it unpowered in diode mode to ground, then measure voltage with the board running. A reading far from known-good usually points to a short or open on that rail, but a single reading isn't proof — compare against a known-good board. No resistance reading is available here. | |||
PPVCORE_S0_CPU_PH1_L | 0.010 | 1.100 | – |
AI: what PPVCORE_S0_CPU_PH1_L is and how to check itPPVCORE_S0_CPU_PH1_L is the CPU core power rail; the S0 in its name indicates the running state, and PH1 suggests a switching-phase node. The archive lists a known-good diode reading of 0.010 to ground and a voltage of 1.100, both guides only, with no condition noted. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode value far above 0.010 usually points to an open or high-resistance path rather than a short; a voltage far from 1.100 points to the core regulator or its feedback. No known-good resistance reading is available here, so compare against a matching rail or a known-good board. | |||
PPVCORE_S0_CPU_PH2 | 0.010 | 1.100 | 9.600R |
AI: what PPVCORE_S0_CPU_PH2 is and how to check itPPVCORE_S0_CPU_PH2 is the CPU core power rail (VCORE) in its running state, judging by the name: S0 means running and PH2 is a phase of the CPU buck converter. The archive lists diode 0.010, voltage 1.100 and resistance 9.600R as known-good readings, but no condition is recorded, so treat them as a guide only. Check it with the board unpowered in diode mode to ground, then measure the voltage with the board powered and running. A diode reading far from 0.010, or a resistance far from 9.600R, usually points to a short or a failed phase on that rail, but one reading alone doesn't confirm a bad part. | |||
PPVCORE_S0_CPU_PH2_L | 0.010 | 1.100 | – |
AI: what PPVCORE_S0_CPU_PH2_L is and how to check itPPVCORE_S0_CPU_PH2_L is the CPU core power rail (VCORE) for the CPU's phase 2 switching node; the S0 in the name indicates it belongs to the running state. From the readings archive, the known-good guide values are a diode reading of 0.010 to ground and 1.100 V with the board powered in S0. To check it, power off and measure diode mode from the rail to ground, then power up and measure the voltage. A diode reading far above 0.010 suggests an open or high-resistance path rather than a short, while a voltage well off 1.100 V under load points to a problem in the core supply or its feedback. No known-good resistance reading is available here, so compare against a matching rail or a known-good board. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
5V3V3_REG_EN | 0.72 | 3.40 | – |
ADAPTER_SENSE | 0.612 | 2.900 | – |
ALL_SYS_PWRGD | 0.49 | – | – |
AP_CLKREQ_Q_L | 0.479 | – | – |
AP_RESET_CONN_L | 0.482 | – | – |
AP_TEMP_SMB_SCL_R | 0.755 | – | – |
AUD_CONNJ1_RING | 0.648 | – | – |
AUD_CONNJ1_TIP | 0.689 | – | – |
AUD_CONNJ1_TIPDET | 0.733 | – | – |
AUD_CONNJ1_USGND | 0.000 | – | – |
AUD_CONNJ1_USGND_DET | OL | – | – |
AUD_CONNJ1_USMIC | 0.000 | – | – |
AUD_SPDIF_OUT | 0.662 | – | – |
BTMUX_SEL | 0.515 | 3.300 | – |
CHGR_ACIN | 0.54 | 3.910 | – |
CHGR_AGATE | 0.65 | 0.000 | – |
CHGR_AMON | 0.72 | 0.350 | – |
CHGR_BGATE | 0.67 | 5.170 | – |
CHGR_BMON | 0.73 | 0.060 | – |
CHGR_BOOT | 0.59 | 17.360 | – |
CHGR_CELL | 0.71 | 3.480 | – |
CHGR_CSI_N | 0.64 | 16.510 | – |
CHGR_CSI_P | 0.63 | 16.530 | – |
CHGR_CSI_R_N | – | 16.410 | – |
CHGR_CSI_R_P | – | 16.430 | – |
CHGR_CSO_N | 0.45 | 12.590 | – |
CHGR_CSO_P | 0.45 | 12.590 | – |
CHGR_CSO_R_N | 0.450 | – | – |
CHGR_CSO_R_P | 0.450 | – | – |
CHGR_ICOMP | 0.73 | 2.110 | – |
CHGR_LGATE | 0.46 | 0.940 | – |
CHGR_PHASE | 0.45 | 12.550 | – |
CHGR_RST_L | 0.50 | 3.440 | – |
CHGR_SGATE | 0.656 | 0.020 | – |
CHGR_UGATE | 0.92 | 16.060 | – |
CHGR_VCOMP | 0.72 | 1.860 | – |
CHGR_VFRQ | 0.53 | 0.000 | – |
CHGR_VNEG | 0.54 | 2.090 | – |
CPU_AXG_SENSE_R | 0.01 | – | – |
CPU_PROCHOT_L | 0.07 | – | – |
CPU_VCCSA_VID<0> | 0.37 | – | – |
CPU_VCCSA_VID<1> | 0.36 | – | – |
CPU_VCCSASENSE_DIV | 0.50 | – | – |
CPU_VCCSENSE_R | 0.01 | – | – |
CPU_VIDALERT_L | 0.08 | – | – |
CPU_VIDSCLK | 0.06 | – | – |
CPU_VIDSOUT | 0.07 | – | – |
CPUIMVP_AXG_PGOOD | 0.62 | – | – |
CPUIMVP_AXG_PWM2 | 0.62 | – | – |
CPUIMVP_BOOT1 | 0.60 | – | – |
CPUIMVP_BOOT1G | 0.60 | 4.800 | – |
CPUIMVP_BOOT1G_RC | – | 4.800 | – |
CPUIMVP_BOOT2 | 0.60 | – | – |
CPUIMVP_FBA | 0.67 | – | – |
CPUIMVP_FBB | 0.67 | – | – |
CPUIMVP_IMAXA | 0.64 | – | – |
CPUIMVP_IMAXB | 0.61 | – | – |
CPUIMVP_ISNS1_N | 0.010 | – | – |
CPUIMVP_ISNS1_P | 0.010 | – | – |
CPUIMVP_ISNS1G_N | 0.012 | – | – |
CPUIMVP_ISNS1G_P | 0.012 | – | 11.500R |
CPUIMVP_ISNS2_N | 0.010 | – | 9.600R |
CPUIMVP_ISNS2_P | 0.010 | – | 9.600R |
CPUIMVP_ISNS2G_N | 0.012 | – | – |
CPUIMVP_ISNS2G_P | 0.012 | – | – |
CPUIMVP_ISUM | 0.10 | – | – |
CPUIMVP_ISUM_N | 0.00 | – | – |
CPUIMVP_ISUM1_P | 0.04 | – | – |
CPUIMVP_ISUM2_P | 0.05 | – | – |
CPUIMVP_ISUMG_AVE_P | 0.10 | – | – |
CPUIMVP_ISUMG_N | 0.01 | – | – |
CPUIMVP_ISUMG1_P | 0.05 | – | – |
CPUIMVP_ISUMG2_P | 0.38 | 5.000 | – |
CPUIMVP_LGATE1 | 0.56 | – | – |
CPUIMVP_LGATE1G | 0.56 | – | – |
CPUIMVP_LGATE2 | 0.52 | – | – |
CPUIMVP_NTC | 0.61 | – | – |
CPUIMVP_NTCG | 0.68 | – | – |
CPUIMVP_PGOOD | 0.60 | – | – |
CPUIMVP_PHASE1 | 0.00 | – | – |
CPUIMVP_PHASE1G | 0.00 | – | – |
CPUIMVP_PHASE2 | 0.00 | – | – |
CPUIMVP_SLEW | 0.69 | – | – |
CPUIMVP_TONA | 0.67 | – | – |
CPUIMVP_TONB | 0.67 | – | – |
CPUIMVP_UGATE1 | 0.68 | – | – |
CPUIMVP_UGATE1G | 0.68 | – | – |
CPUIMVP_UGATE2 | 0.68 | – | – |
CPUIMVP_VR_ON | 0.49 | – | – |
CPUIMVP_VSWG | 0.012 | – | – |
CPUIMVP_VSWG2 | 0.012 | – | – |
CPUTHMSNS_ALERT_L | 0.74 | – | – |
CPUTHMSNS_THM_L | 0.75 | – | – |
CPUVCCIOS0_AGND | 0.00 | – | – |
CPUVCCIOS0_CS_N | 0.013 | – | – |
CPUVCCIOS0_CS_P | 0.013 | – | – |
CPUVCCIOS0_DRVH | 0.55 | – | – |
CPUVCCIOS0_DRVL | 0.44 | – | – |
CPUVCCIOS0_EN | 0.52 | – | – |
CPUVCCIOS0_FB | 0.51 | – | – |
CPUVCCIOS0_FSEL | 0.00 | – | – |
CPUVCCIOS0_LL | 0.013 | 1.000 | 12.500R |
CPUVCCIOS0_OCSET | 0.52 | – | – |
CPUVCCIOS0_PGOOD | 0.50 | – | – |
CPUVCCIOS0_RTN | 0.51 | – | – |
CPUVCCIOS0_SREF | 0.53 | – | – |
CPUVCCIOS0_VBST | 0.53 | – | – |
CPUVCCIOS0_VO | 0.52 | – | – |
DDRREG_1V8_VREF | 0.64 | – | – |
DDRREG_DRVH | 0.62 | – | – |
DDRREG_DRVL | 0.45 | – | – |
DDRREG_EN | 0.47 | – | – |
DDRREG_FB | 0.69 | – | – |
DDRREG_LL | 0.127 | 1.500 | 126.000 |
DDRREG_MODE | 0.53 | – | – |
DDRREG_TRIP | 0.74 | – | – |
DDRREG_VBST | 0.61 | – | – |
DDRREG_VDDQSNS | 0.14 | – | – |
DDRREG_VTTSNS | 0.46 | – | – |
FW_5KPD_DET_RC | OL | – | – |
FW_PWR_EN | 0.45 | – | – |
FW_PWR_EN_L | 0.43 | – | – |
FWPORT_PWREN_L_DIV | – | 7.470 | – |
GND | – | 0.002 | – |
GND_CPUIMVP_SGND | 0.00 | – | – |
IR_RX_OUT | 0.71 | – | – |
ISNS_1V5_S3_DDR_N | 0.127 | 1.500 | 126.000 |
ISNS_1V5_S3_DDR_P | 0.127 | 1.500 | 126.000 |
KBDLED_SW | – | 5.000 | – |
LCD_IG_PWR_EN | 0.58 | – | – |
LED_RETURN_1 | 0.63 | – | – |
LED_RETURN_2 | 0.63 | – | – |
LED_RETURN_3 | 0.63 | – | – |
LED_RETURN_4 | 0.63 | – | – |
LED_RETURN_5 | 0.63 | – | – |
LED_RETURN_6 | 0.63 | – | – |
LPC_CLK33M_LPCPLUS | – | 1.600 | – |
LVDS_CONN_A_CLK_F_N | 0.66 | – | – |
LVDS_CONN_A_CLK_F_P | 0.66 | – | – |
LVDS_DDC_CLK | 0.62 | – | – |
LVDS_DDC_DATA | 0.62 | – | – |
LVDS_IG_A_DATA_N<0> | 0.65 | – | – |
LVDS_IG_A_DATA_N<1> | 0.65 | – | – |
LVDS_IG_A_DATA_N<2> | 0.65 | – | – |
LVDS_IG_A_DATA_P<0> | 0.65 | – | – |
LVDS_IG_A_DATA_P<1> | 0.65 | – | – |
LVDS_IG_A_DATA_P<2> | 0.65 | – | – |
MEMVTT_EN | 0.45 | – | – |
P1V5CPU_EN | – | 3.100 | – |
P1V8S0_SW | 0.120 | – | – |
P3V3S5_DRVH | 0.64 | 3.90 | – |
P3V3S5_DRVL | 0.45 | – | – |
P3V3S5_ENTRIP | 0.45 | 0.70 | – |
P3V3S5_LL | 0.13 | 3.30 | – |
P3V3S5_VBST | 0.59 | 7.70 | – |
P3V3S5_VFB | 0.72 | 2.00 | – |
P3V3S5_VO2 | 0.13 | 3.30 | – |
P3V42G3H_FB | 0.558 | 3.400 | – |
P3V42G3H_REF3 | 0.878 | 3.200 | – |
P3V42G3H_SW | 0.350 | 3.500 | – |
P3V42G3H_TON | – | 15.000 | – |
P5V3V3_PGOOD | 0.59 | 3.30 | – |
P5V3V3_REG_EN | – | 3.400 | – |
P5VP3V3_REG3 | 0.64 | 3.30 | – |
P5VP3V3_VREF | 0.68 | 2.00 | – |
P5VS3_DRVH | 0.87 | 5.50 | – |
P5VS3_DRVL | 0.45 | 0.60 | – |
P5VS3_EN_L | – | 3.400 | – |
P5VS3_ENTRIP | 0.44 | 1.10 | – |
P5VS3_LL | 0.43 | 5.00 | – |
P5VS3_VBST | 0.61 | 9.90 | – |
P5VS3_VFB | 0.72 | 2.00 | – |
P5VS3_VO1 | 0.43 | 5.00 | – |
P18V5_DCIN_CONN_R | 2.900 | 16.220 | – |
PBUS_G3H_R | 0.467 | 12.490 | – |
PCH_DSWVRMEN | – | 3.300 | – |
PCH_INTVRMEN_L | – | 3.300 | – |
PCH_SRTCRST_L | – | 3.300 | – |
PCIE_AP_D2R_PI_N | 0.381 | – | – |
PCIE_AP_D2R_PI_P | 0.380 | – | – |
PCIE_AP_R2D_N | OL | – | – |
PCIE_AP_R2D_P | OL | – | – |
PCIE_CLK100M_AP_CONN_N | 0.400 | – | – |
PCIE_CLK100M_AP_CONN_P | 0.400 | – | – |
PCIE_WAKE_L | 0.580 | 3.300 | – |
PLT_RESET_L | 0.42 | – | – |
PLT_RST_BUF_L | 0.00 | – | – |
PM_DSW_PWRGD | – | 3.300 | – |
PM_PWRBTN_L | – | 3.400 | – |
PM_S0_PGOOD | 0.60 | – | – |
PM_SLP_S4_L | 3.300 | – | – |
PP0V75_S0_DDRVTT | 0.45 | – | – |
PP1V2_S5_SMC_VDDC | – | 1.200 | – |
PP1V05_S0 | 0.013 | 1.054 | 0.000R |
PP1V5_S0 | 0.29 | – | – |
PP1V05_S0_PCH | 0.012 | – | 12.500R |
PP1V05_S0_PCH_VCCADPLL | 0.15 | – | – |
PP1V05_S0_PCH_VCCCLKDMI_R | 0.012 | – | 12.500R |
PP1V5_S3 | 0.127 | 1.500 | 126.000 |
PP1V5_S3_DDR | 0.127 | 1.500 | 126.000 |
PP1V5_S3RS0 | 0.100 | – | 100.000R |
PP1V05_SUS | 0.48 | – | – |
PP1V8_S0 | 0.120 | – | – |
PP1V8_S0_CPU_VCCPLL_R | 0.110 | – | 110.000R |
PP1V8_S0_PCH_VCCTX_LVDS_F | 0.120 | – | – |
PP3V3_LCDVDD_SW | 0.60 | – | – |
PP3V3_LCDVDD_SW_F | 0.60 | – | – |
PP3V3_S0 | 0.339 | – | – |
PP3V3_S0_CPUTHMSNS_R | 0.39 | – | – |
PP3V3_S0_LCD_F | 0.34 | – | – |
PP3V3_S0_PCH_VCC3_3_CLK_F | 0.350 | – | – |
PP3V3_S0_PCH_VCC3_3_CLK_R | 0.350 | – | – |
PP3V3_S3 | – | 3.300 | – |
PP3V3_S3RS4_BT_F | 0.395 | 3.300 | – |
PP3V3_S4 | – | 3.300 | – |
PP3V3_S5 | 0.49 | 3.300 | – |
PP3V3_S5_AVREF_SMC | – | 3.200 | – |
PP3V3_SUS | 0.34 | 3.300 | – |
PP3V3_WLAN | 2.710 | – | – |
PP3V42_G3H | 0.35 | 3.400 | – |
PP5V_S0 | 0.37 | 5.000 | – |
PP5V_S0_CPUIMVP_VCC | 0.38 | 5.000 | – |
PP5V_S0_CPUVCCIOS0_VCC | 0.38 | – | – |
PP5V_S0_HDD | – | 5.000 | – |
PP5V_S0_HDD_FLT | 0.37 | 5.000 | – |
PP5V_S0_VCCSAS0_VCC | 0.37 | – | – |
PP5V_S3 | 0.43 | 5.000 | – |
PP5V_S3_IR_R | 0.42 | – | – |
PP5V_S3_USB_A_F | 0.518 | – | – |
PP5V_S5 | 0.52 | 5.00 | – |
PP5V_S5_P18V5S5_VIN | – | 5.000 | – |
PP5V_SUS | – | 5.000 | – |
PP5V1_CHGR_VDD | 0.46 | 5.060 | – |
PP5V1_CHGR_VDDP | 0.46 | 5.030 | – |
PP15V_T29 | 0.530 | – | – |
PP18V5_DCIN_FUSE | 2.865 | 16.350 | – |
PPBUS_FW_FWPWRSW_D | – | 12.490 | – |
PPBUS_FW_FWPWRSW_F | – | 12.490 | – |
PPBUS_G3H | 0.450 | 12.490 | – |
PPBUS_S0_LCDBKLT_FUSED | 0.450 | – | – |
PPBUS_S5_HS_COMPUTING_ISNS | 0.050 | 12.490 | 0.000R |
PPBUS_S5_HS_OTHER_ISNS | 0.45 | 12.490 | – |
PPBUS_SW_BKL | 0.430 | – | – |
PPBUS_SW_LCDBKLT_PWR_SW | 0.430 | – | – |
PPCHGR_DCIN | 0.62 | 16.000 | – |
PPCPUVCCIO_S0_REG_R | 0.013 | 1.000 | – |
PPDCIN_G3H | 2.865 | 16.350 | – |
PPDCIN_G3H_CHGR | 0.640 | 16.420 | – |
PPDCIN_G3H_INRUSH | – | 16.420 | – |
PPVBAT_G3H_CHGR_R | 0.450 | – | – |
PPVBAT_G3H_CHGR_REG | 0.450 | 12.500 | – |
PPVBAT_G3H_CONN | OL | – | – |
PPVCCSA_S0_CPU | 0.053 | 0.800 | 52.000R |
PPVCCSA_S0_REG_R | 0.053 | 0.807 | 52.000R |
PPVCORE_S0_AXG | 0.012 | – | – |
PPVCORE_S0_AXG_R | 0.012 | – | – |
PPVCORE_S0_AXG2_L | 0.012 | – | – |
PPVCORE_S0_CPU | 0.010 | 1.100 | 9.600R |
PPVCORE_S0_CPU_PH1 | 0.010 | 1.100 | – |
PPVCORE_S0_CPU_PH1_L | 0.010 | 1.100 | – |
PPVCORE_S0_CPU_PH2 | 0.010 | 1.100 | 9.600R |
PPVCORE_S0_CPU_PH2_L | 0.010 | 1.100 | – |
PPVIN_G3H_P3V42G3H | 0.570 | 15.950 | – |
PPVIN_SW_T29BST | 0.450 | – | – |
PPVOUT_SW_LCDBKLT | 0.59 | – | – |
PPVOUT_SW_LCDBKLT_FB | 0.590 | – | – |
PPVRTC_G3H | 0.444 | 3.300 | – |
PPVTTDDR_S3 | 0.49 | – | – |
PSOC_MISO | – | 1.100 | – |
PVCCSA_EN | 0.53 | – | – |
PVCCSA_PGOOD | 0.50 | – | – |
RTC_RESET_L | – | 3.300 | – |
SATA_HDD_D2R_C_N | OL | – | – |
SATA_HDD_D2R_C_P | OL | – | – |
SATA_HDD_D2R_N | 0.29 | – | – |
SATA_HDD_D2R_P | 0.30 | – | – |
SATA_HDD_D2R_RDRIN_N | 0.02 | – | – |
SATA_HDD_D2R_RDRIN_P | 0.02 | – | – |
SATA_HDD_D2R_RDROUT_N | 0.33 | – | – |
SATA_HDD_D2R_RDROUT_P | 0.33 | – | – |
SATA_HDD_R2D_C_N | 0.27 | – | – |
SATA_HDD_R2D_C_P | 0.27 | – | – |
SATA_HDD_R2D_N | OL | – | – |
SATA_HDD_R2D_P | OL | – | – |
SATA_HDD_R2D_RDRIN_N | 0.02 | – | – |
SATA_HDD_R2D_RDRIN_P | 0.02 | – | – |
SATA_HDD_R2D_RDROUT_N | 0.33 | – | – |
SATA_HDD_R2D_RDROUT_P | 0.33 | – | – |
SATARDRVR_EN | 0.43 | – | – |
SATARDRVR_I2C_ADDR0 | 0.44 | – | – |
SATARDRVR_I2C_ADDR1 | 0.46 | – | – |
SATARDRVR_I2C_EN_L | 0.00 | – | – |
SATARDRVR_REXT | 0.59 | – | – |
SATARDRVR_TEST | 0.44 | – | – |
SMBUS_PCH_CLK | 0.40 | – | – |
SMBUS_PCH_DATA | 0.40 | – | – |
SMBUS_SMC_1_S0_SCL | 0.56 | – | – |
SMBUS_SMC_1_S0_SDA | 0.56 | – | – |
SMBUS_SMC_5_G3_SCL | 0.53 | 3.480 | – |
SMBUS_SMC_5_G3_SDA | 0.53 | 3.480 | – |
SMC_BATLOW_L | – | 3.200 | – |
SMC_BC_ACOK | 0.50 | 3.300 | – |
SMC_BC_ACOK_VCC | 0.530 | – | – |
SMC_BIL_BUTTON_L | 0.74 | – | – |
SMC_DELAYED_PWRGD | 0.64 | – | – |
SMC_LID | – | 3.400 | – |
SMC_LID_R | 0.84 | – | – |
SMC_LRESET_L | – | 3.300 | – |
SMC_MANUAL_RST_L | – | 2.800 | – |
SMC_ONOFF_L | – | 3.400 | – |
SMC_PM_G2_EN | – | 3.400 | – |
SMC_RESET_L | 0.492 | 3.400 | – |
SMC_SSD_OOBD2R_R_L | 0.54 | – | – |
SMC_TPAD_RST_L | – | 3.400 | – |
SPI_MLB_CLK | 0.65 | – | – |
SPI_MLB_CS_L | 0.63 | – | – |
SPI_MLB_MISO | 0.51 | – | – |
SPI_MLB_MOSI | 0.52 | – | – |
SPI_WP_L | 0.64 | – | – |
SPIROM_USE_MLB | 0.53 | – | – |
SSD_OOB1V0REF | 0.65 | – | – |
SSD_OOBD2R_L | 1.31 | – | – |
SSD_OOBD2R_R_L | 0.65 | – | – |
SSD_OOBR2D_L | 0.84 | – | – |
SYS_DETECT_L | 2.600 | – | – |
SYS_LED_ANODE_R | OL | – | – |
SYS_LED_ILIM | – | 5.000 | – |
SYS_PWROK_R | 0.49 | – | – |
SYSCLK_CLK25M_X2_R | 0.450 | – | – |
T29BST_BOOST | 0.450 | – | – |
THMSNS_D1_N | 0.76 | – | – |
THMSNS_D1_P | 0.77 | – | – |
THMSNS_D2_N | 0.75 | – | – |
THMSNS_D2_P | 0.75 | – | – |
TP_DDRREG_PGOOD | 0.57 | – | – |
UNCONNECTED_126 | 0.62 | – | – |
UNCONNECTED_144 | OL | – | – |
USB_BT_CONN_N | 0.710 | – | – |
USB_BT_CONN_P | 0.714 | – | – |
USB_BT_N | 0.703 | – | – |
USB_BT_P | 0.705 | – | – |
USB_BT_WAKEN | 0.712 | – | – |
USB_BT_WAKEP | 0.717 | – | – |
USB_EXTA_MUXED_F_N | 0.572 | – | – |
USB_EXTA_MUXED_F_P | 0.573 | – | – |
USB3_EXTA_RX_F_N | 0.347 | – | – |
USB3_EXTA_RX_F_P | 0.354 | – | – |
USB3_EXTA_TX_F_N | 0.755 | – | – |
USB3_EXTA_TX_F_P | 0.755 | – | – |
VCCSAS0_CS_N | 0.053 | – | 52.000R |
VCCSAS0_CS_P | 0.053 | – | 52.000R |
VCCSAS0_DRVH | 0.57 | – | – |
VCCSAS0_DRVL | 0.44 | – | – |
VCCSAS0_FSEL | 0.00 | – | – |
VCCSAS0_LL | 0.050 | 0.819 | 52.000R |
VCCSAS0_OCSET | 0.50 | – | – |
VCCSAS0_RTN_DIV | 0.51 | – | – |
VCCSAS0_SET0 | 0.53 | – | – |
VCCSAS0_SET1 | 0.53 | – | – |
VCCSAS0_SREF | 0.53 | – | – |
VCCSAS0_VBST | 0.53 | – | – |
VCCSAS0_VO | 0.50 | – | – |
WIFI_EVENT_L_R | 0.761 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PPBUS_G3H read on the 820-3115?
OpenBoardData's known-good values for PPBUS_G3H on the 820-3115: diode 0.450, voltage 12.490. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V42_G3H read on the 820-3115?
OpenBoardData's known-good values for PP3V42_G3H on the 820-3115: diode 0.35, voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP5V_S5 read on the 820-3115?
OpenBoardData's known-good values for PP5V_S5 on the 820-3115: diode 0.52, voltage 5.00. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-3115 board?
Open your own 820-3115 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License