Apple laptop board · OpenBoardData

820-01987 known-good readings

Known-good readings for the Apple laptop board 820-01987: 1,658 nets, including 109 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 109 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-01987.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 109 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 49

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V8_G3S0.308––
AI: what PP1V8_G3S is and how to check it

PP1V8_G3S is a 1.8 V rail; the "G3S" part of the name indicates it belongs to the always-on G3H group, so it should be present whenever the board has power. The archive lists one known-good diode reading of 0.308 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage at the rail. A diode value far from 0.308 suggests a short or leaky load on the rail, while a missing or low voltage with a normal diode reading points more toward the supply feeding it. These are guides only, so confirm against a matching rail or a known-good board before replacing anything.

PP1V8_G3S_REG0.306––
AI: what PP1V8_G3S_REG is and how to check it

PP1V8_G3S_REG is a 1.8 V rail; the G3S part of the name marks it as an always-on startup rail, so it should be present whenever the board has power. The only known-good reading here is a diode value of 0.306 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage on the rail. A diode reading far from 0.306 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.

PP1V8_G3S_WLANBT0.310––
AI: what PP1V8_G3S_WLANBT is and how to check it

PP1V8_G3S_WLANBT is the 1.8 V rail feeding the WLAN/Bluetooth section; the G3S part of the name indicates it is an always-on rail (that's from the name, not from a schematic). The only known-good reading here is a diode value of 0.310 to ground, with no condition recorded and no known-good voltage or resistance value. Check it with the board unpowered in diode mode, black probe on ground and red on the rail, then confirm the voltage with power applied. A diode reading far below 0.310 suggests a short or leaky load on the rail; far above it suggests an open path, but one reading alone doesn't confirm a bad part.

PP3V_G3H_RTC0.457––
AI: what PP3V_G3H_RTC is and how to check it

PP3V_G3H_RTC is an always-on 3V rail feeding the RTC section, based on its name (G3H usually means always-on). The archive lists a known-good diode reading of 0.457 to ground; no known-good voltage reading is recorded here.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.457.
  • Then power the board and measure the voltage on the rail; the archive has no known-good voltage, so compare against a known-good board or matching net.
  • A diode reading far from 0.457 suggests a short or leak on that rail, but one reading alone doesn't confirm a bad part.
PP3V3_G3H0.4203.3000.200R
AI: what PP3V3_G3H is and how to check it

PP3V3_G3H is an always-on 3.3 V rail; the "G3H" suffix means always-on (from the name). Known-good readings for this board: diode 0.420, voltage 3.300, resistance 0.200R — community values, so treat them as a guide.

  • Check diode mode to ground with the board unpowered, then measure the voltage with power applied.
  • A diode reading far from 0.420 usually points to a short or a faulty part on the rail; a missing 3.300 V with a normal diode reading points more to the supply side.
  • No known-good current-draw reading here, so compare against a matching rail or a known-good board.
PP3V3_G3H_BMU0.414––
AI: what PP3V3_G3H_BMU is and how to check it

PP3V3_G3H_BMU is a 3.3 V always-on rail, judging from its name: G3H means always on, and BMU likely refers to the battery management side. The archive lists one known-good diode reading of 0.414 to ground; there is no known-good voltage reading here.

  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.414.
  • Then power the board and measure the voltage on the rail; no known-good voltage is recorded, so compare against a known-good board or the rail's nominal 3.3 V.
  • A diode reading far below 0.414 usually points to a short or a leaky part on the rail; a reading far above can mean an open connection.
PP3V3_G3H_DFUMUXOL––
AI: what PP3V3_G3H_DFUMUX is and how to check it

PP3V3_G3H_DFUMUX is a 3.3 V always-on rail; the G3H part of the name indicates it is present whenever the board has power, and DFUMUX suggests it feeds a USB/DFU-related multiplexer (from the name, not from board data). The only archived reading is a diode value of OL to ground, which is a guide only and is not a known-good value; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from OL, or a voltage well off 3.3 V, usually points to a short or a failed source on that rail, but one reading alone doesn't confirm a bad part.

PP3V3_G3H_MESA_SW0.370––
AI: what PP3V3_G3H_MESA_SW is and how to check it

PP3V3_G3H_MESA_SW is a 3.3 V always-on rail (the G3H part of the name means always-on), likely a switched branch feeding the MESA section. The archive's only known-good reading is a diode value of 0.370 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage; no known-good voltage reading is available here. A diode reading far from 0.370, or a missing or low voltage, usually points to a short, an open feed, or a failed switch on that branch, but one reading alone doesn't confirm a bad part.

PP3V3_G3H_PMU_VDDMAIN0.415––
AI: what PP3V3_G3H_PMU_VDDMAIN is and how to check it

PP3V3_G3H_PMU_VDDMAIN is the 3.3 V always-on rail feeding the PMU's main supply; the G3H part of the name indicates it's up whenever the board has power, before the main power sequence starts (from the name, general convention). The archive lists a known-good diode reading of 0.415 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading here, so compare against a matching always-on rail or a known-good board. A diode reading far below 0.415 suggests a short or leaky load on the rail, while a much higher or open reading points to a broken trace or missing connection. Treat these as a guide only, since community readings vary with board state.

PP3V3_G3H_PMU_VINRTC_R0.370––
AI: what PP3V3_G3H_PMU_VINRTC_R is and how to check it

PP3V3_G3H_PMU_VINRTC_R is an always-on 3.3 V rail feeding the PMU and RTC input, judging by its name (G3H = always on). The only known-good figure here is a diode reading of 0.370 to ground, board unpowered; there is no known-good voltage reading for this rail. Check it with the board off in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.370 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3H_RSLOC0.371––
AI: what PP3V3_G3H_RSLOC is and how to check it
  • PP3V3_G3H_RSLOC is a 3.3 V rail; the "G3H" part of the name marks it as an always-on startup rail, and "RSLOC" is a local variant of it (this is from the name, not from board data).
  • Known-good: diode-to-ground 0.371 in diode mode. That's the only known-good value recorded here; there's no known-good voltage or resistance reading for this rail.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.371. Then power the board and measure the DC voltage at the rail — it should sit near 3.3 V whenever the board has power.
  • A diode reading far below 0.371 usually points to a short or a leaky part on the rail; far above it can mean an open trace or a missing connection. A missing 3.3 V with power applied points to the rail's source or its enable, not the load.
  • These are community readings and vary with board state, so treat them as a guide and confirm on a matching rail or a known-good board before replacing anything.
PP3V3_G3H_RTC0.371––
AI: what PP3V3_G3H_RTC is and how to check it

PP3V3_G3H_RTC is an always-on 3.3 V rail, judged from its name: G3H usually means it is present whenever power is connected, and RTC suggests it also feeds the real-time clock circuit. The archive lists one known-good diode reading of 0.371 to ground, with no condition recorded, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.371 usually points to a short or a leaky part on that rail, but a single reading is only a guide, so compare against a matching rail or a known-good board before condemning anything.

PP3V3_G3H_RTC_DFR0.369––
AI: what PP3V3_G3H_RTC_DFR is and how to check it

PP3V3_G3H_RTC_DFR is a 3.3 V always-on rail, judging from the name: "PP3V3" for the voltage, "G3H" for always-on, and "RTC" for the real-time clock domain. The archive gives one known-good diode reading of 0.369 to ground, with no condition noted; there is no known-good voltage reading here.

  • Check it unpowered in diode mode to ground, then check the voltage with power applied.
  • A diode reading far from 0.369 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.
  • With no known-good voltage listed, compare the powered voltage against what the rail name implies (about 3.3 V) and against a matching rail on a known-good board.
PP3V3_G3H_RTC_MESA0.369––
AI: what PP3V3_G3H_RTC_MESA is and how to check it

PP3V3_G3H_RTC_MESA is a 3.3 V always-on rail, judging from its name: G3H usually means it's present whenever power is connected, and RTC/MESA suggest it feeds the real-time clock and related logic. The archive lists one known-good diode reading of 0.369 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage. A diode reading far from 0.369 usually points to a short or a damaged part on that net, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3H_RTC_REG_R0.3723.300–
AI: what PP3V3_G3H_RTC_REG_R is and how to check it
  • What it is: PP3V3_G3H_RTC_REG_R is an always-on 3.3 V rail feeding the RTC/real-time clock area, judged from its name (G3H = always on, RTC = clock domain). It should be present whenever the board has power, before the main power sequence runs.
  • Known-good readings (community guide): diode 0.372 to ground, and 3.300 V with power applied.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode but missing 3.3 V points upstream to the rail's source or its enable. No known-good resistance reading is recorded here, so compare against a matching rail or a known-good board.
PP3V3_G3H_SSD00.4203.300–
AI: what PP3V3_G3H_SSD0 is and how to check it

PP3V3_G3H_SSD0 is the always-on 3.3 V rail feeding SSD0, based on its name (G3H = always on, SSD0 = first SSD supply). Known-good readings in the archive: diode 0.420 to ground and 3.300 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.420 suggests a short or leaky part on the rail; a missing or low voltage points to the supply that generates it or a load pulling it down. No known-good resistance value is recorded here, so compare against a matching rail or a known-good board.

PP3V3_G3HSW_DFR0.570––
AI: what PP3V3_G3HSW_DFR is and how to check it

PP3V3_G3HSW_DFR is a 3.3 V rail; the G3H in its name indicates it is always-on (from the name), and DFR likely marks a specific branch or device feed. The only known-good reading here is a diode value of 0.570 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.570 usually points to a short or a leaky load on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3S0.379––
AI: what PP3V3_G3S is and how to check it

PP3V3_G3S is a 3.3 V rail; the G3S suffix, from its name, marks it as an always-on startup-stage rail on this 820-01987. The only known-good reading here is a diode of 0.379 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.379 usually points to a short or a leaky part on the rail, but confirm with a voltage measurement before replacing anything.

PP3V3_G3S_KBD0.380––
AI: what PP3V3_G3S_KBD is and how to check it

PP3V3_G3S_KBD is a 3.3 V rail; the "G3S" part of the name marks it as an always-on startup-stage rail, and "KBD" suggests it feeds keyboard circuitry (from the name, not from board data).

  • Known-good: diode-to-ground 0.380. No known-good voltage reading here.
  • Check: board unpowered, diode mode, black probe to ground, red on the rail; then power up and measure the voltage.
  • A diode reading far from 0.380 usually points to a short or a leaky part on that rail, but one reading isn't proof — compare with a known-good board before replacing anything.
PP3V3_G3S_TPAD0.379––
AI: what PP3V3_G3S_TPAD is and how to check it
  • What it is: PP3V3_G3S_TPAD is a 3.3 V rail for the trackpad, from its name. The G3S in the name marks it as an always-on rail in the startup sequence, also from the name.
  • Known-good reading: diode 0.379 in the readings archive; no voltage or resistance value is recorded here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_G3S_TPAD to ground, then apply power and measure the rail voltage.
  • If it's far off: a diode reading well below 0.379 suggests a short or a leaky part on the rail; a much higher reading suggests an open path. Treat the archive value as a guide only, since readings vary with board state, and confirm before replacing anything.
PP3V3_G3S_WLANBT0.379––
AI: what PP3V3_G3S_WLANBT is and how to check it

PP3V3_G3S_WLANBT is the 3.3 V rail feeding the WLAN/Bluetooth section, and the G3S in its name indicates it is an always-on rail (from the name). The archive lists one known-good diode reading of 0.379 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.379. Then power the board and check the voltage at the rail. A diode reading far from 0.379 usually points to a short or a leaky part on that rail, but confirm with more than one reading before replacing anything.

PP5V_G3H_LDO0.491––
AI: what PP5V_G3H_LDO is and how to check it

PP5V_G3H_LDO is a 5 V always-on LDO rail; the G3H part of the name indicates it should be present whenever the board has power, not just after the main power-on sequence (this is from the name, not the board data).

  • Known-good: diode reading 0.491 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, measure diode mode from PP5V_G3H_LDO to ground; then power up and measure the DC voltage on the rail.
  • A diode reading far from 0.491 usually points to a short or a leaky component on that rail, but one reading isn't proof — compare with a known-good board or matching net before replacing anything.
PP5V_G3S0.4285.0000.100R
AI: what PP5V_G3S is and how to check it

PP5V_G3S is a 5 V rail; the "G3S" suffix is from its name and in Apple naming marks a rail that stays up in the always-on G3 state. Known-good readings in the archive: diode 0.428 to ground, 5.000 V with power applied, and 0.100R resistance. Check it with the board unpowered in diode mode from the rail to ground, then confirm the 5.000 V with power applied. A diode reading far from 0.428 usually points to a short or a leaky part on that rail, while a correct diode but missing 5 V points upstream at its supply or enable. No known-good current-load or ripple figure is recorded here.

PP5V_G3S_ALSCAM0.423––
AI: what PP5V_G3S_ALSCAM is and how to check it

PP5V_G3S_ALSCAM is a 5 V rail; the G3S part of the name indicates it is an always-on rail (from the name), and ALSCAM suggests it feeds the camera circuit (also from the name only).

  • Known-good reading in the archive: diode 0.423 to ground. No known-good voltage reading here.
  • Check with the board unpowered: multimeter in diode mode, black probe on ground, red on the rail, and compare with 0.423.
  • Then power the board and measure the voltage on the rail; it should sit near 5 V, but there is no archived voltage value to compare against.
  • A diode reading far below 0.423 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection. One reading alone doesn't confirm a bad part.
PP5V_G3S_CPUREG_MISC0.420––
AI: what PP5V_G3S_CPUREG_MISC is and how to check it

PP5V_G3S_CPUREG_MISC is a 5 V rail; the G3S part of the name indicates it belongs to the always-on startup group, and CPUREG_MISC suggests it feeds miscellaneous CPU regulator circuitry (that part is from the name, not from board data).

  • Known-good: diode reading 0.420 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • Check it with the board off: diode mode, black probe on ground, red on the rail, and compare with 0.420.
  • Then power the board and measure the voltage on the rail; since no known-good voltage is listed, compare against a matching rail or a known-good board.
  • A diode reading far below 0.420 usually points to a short or a leaky part on that rail; a much higher reading can mean an open trace or missing connection. One reading alone doesn't confirm a bad part.
PP5V_G3S_DFR_FILT0.428––
AI: what PP5V_G3S_DFR_FILT is and how to check it

PP5V_G3S_DFR_FILT is a 5 V rail; from its name, the G3S part marks it as an always-on (G3H) startup rail, and the FILT suffix suggests it is a filtered version of that supply. The archive lists one known-good diode reading of 0.428 to ground, with no condition recorded and no known-good voltage reading here.

  • Check it unpowered in diode mode from the net to ground, then measure the voltage with the board powered.
  • A diode reading far from 0.428 usually points to a short or a leaky part on the rail, but a single reading is only a guide and varies with board state.
  • With no known-good voltage listed, compare against the same rail on a known-good board rather than assuming a value.
PP5V_G3S_EDRAMPVCC0.426––
AI: what PP5V_G3S_EDRAMPVCC is and how to check it
  • What it is: PP5V_G3S_EDRAMPVCC is a 5 V rail; the G3S part of the name indicates it is always on (from the name). The EDRAMPVCC suffix suggests it feeds eDRAM power, but that is general interpretation, not from this board's data.
  • Known-good reading: diode 0.426 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. Confirm with the voltage measurement before replacing anything.
PP5V_G3S_EDRAMVCC0.426––
AI: what PP5V_G3S_EDRAMVCC is and how to check it
  • What it is: PP5V_G3S_EDRAMVCC is a 5 V rail; the G3S part of the name indicates it is always on (from the name), and EDRAMVCC suggests it feeds memory supply.
  • Known-good reading: diode 0.426 to ground, from the readings archive (community contribution, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground and compare with 0.426; then power up and measure the voltage, expecting about 5 V.
  • If far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. Confirm with a second measurement before replacing anything.
PP5V_G3S_FAN0.423––
AI: what PP5V_G3S_FAN is and how to check it

PP5V_G3S_FAN is a 5 V fan rail that is always on when the board has power, judged from its G3S/G3H naming (general naming convention, not from board data). The only known-good reading here is a diode reading of 0.423; no known-good voltage reading is recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.423 usually points to a short or a damaged component on that net, but confirm with a second measurement before replacing anything.

PP5V_G3S_KBD0.4265.000–
AI: what PP5V_G3S_KBD is and how to check it

PP5V_G3S_KBD is a 5 V always-on rail, judged from its name (G3S = always on, KBD = keyboard side); the parts on it aren't known here. Known-good readings in the archive: diode 0.426 to ground and 5.000 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.426 usually points to a short or a leaky part on that rail; a missing 5 V with a normal diode reading points upstream at its source or enable. No known-good resistance reading is listed here.

PP5V_G3S_TPAD0.423––
AI: what PP5V_G3S_TPAD is and how to check it

PP5V_G3S_TPAD is a 5 V rail for the trackpad, and the G3S in its name indicates it is an always-on (G3H) rail. The only known-good reading in the archive is a diode value of 0.423 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.423 usually points to a short or a leaky part on the rail, while a much higher reading can mean an open trace or a missing connection. A missing voltage with a normal diode reading suggests the rail is not being enabled or its source is not coming up.

PP5V_G3S_TPAD_CONN0.425––
AI: what PP5V_G3S_TPAD_CONN is and how to check it

PP5V_G3S_TPAD_CONN is the 5 V rail feeding the trackpad connector; the G3S part of the name indicates it is an always-on (G3H) rail, from the name. The only known-good reading here is a diode value of 0.425 to ground, with no condition listed; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the connector. A diode reading far below 0.425 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken trace or missing feed. This is a guide only, and the voltage expected here is not documented.

PP5V_G3S_VCCIOPVCC0.425––
AI: what PP5V_G3S_VCCIOPVCC is and how to check it

PP5V_G3S_VCCIOPVCC is a 5 V rail; the G3S part of the name indicates it is always on (from the name, not from a schematic). The archive lists one known-good reading: diode mode 0.425 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.425 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

PP5V_G3S_VCCIOVCC0.425––
AI: what PP5V_G3S_VCCIOVCC is and how to check it

PP5V_G3S_VCCIOVCC is a 5 V rail; the "G3S" part of the name indicates it belongs to the always-on (G3) group, so it should be present whenever the board has standby power. The archived reading for this net is a diode value of 0.425 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the net to ground, then apply power and measure the voltage at the net. A diode reading far from 0.425 usually points to a short or a damaged component on that rail, but one reading alone isn't proof, so compare against a matching net or a known-good board before replacing anything.

PPBUS_G3H0.33612.600–
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery-charging bus on this board; the "G3H" suffix, from the name, marks it as an always-on rail. Known-good readings in the archive: diode 0.336 to ground and 12.600 V with power applied. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.336 suggests a short or leaky part on the rail; a voltage far from 12.600 V points to the charging circuit not coming up. No known-good resistance reading is recorded here, so compare against a matching rail on a known-good board if needed.

PPBUS_G3H_SPKRAMP_LEFT0.33612.600–
AI: what PPBUS_G3H_SPKRAMP_LEFT is and how to check it
  • What it is: From the name, PPBUS_G3H_SPKRAMP_LEFT is the always-on PPBUS rail feeding the left speaker amplifier; "G3H" means it should be present whenever the board has power, not only after the main rails come up.
  • Known-good readings: diode 0.336 and voltage 12.600, from the readings archive (community-contributed, so treat as a guide; no condition is recorded).
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky load on that rail; a missing or low voltage with a normal diode reading points upstream at the supply that generates it. No known-good resistance reading is available here, so compare against a matching net or a known-good board.
PPBUS_G3H_SPKRAMP_RIGHT0.33812.600–
AI: what PPBUS_G3H_SPKRAMP_RIGHT is and how to check it

PPBUS_G3H_SPKRAMP_RIGHT is, from its name, the always-on G3H main bus rail feeding the right speaker amp on the 820-01987. The archive gives a known-good diode reading of 0.338 and a voltage of 12.600, with no condition noted, so treat these as a guide only. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.338 suggests a short or leaky load on the rail; a voltage well off 12.600 points to a supply or enable problem upstream. No known-good resistance reading is listed here, so compare against a matching rail or a known-good board.

PPBUS_G3H_SSD00.33612.600–
AI: what PPBUS_G3H_SSD0 is and how to check it

PPBUS_G3H_SSD0 is the main bus rail feeding the SSD section; the G3H part of the name indicates it is always-on (from the name). Known-good readings in the archive: diode 0.336 and voltage 12.600, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.336 suggests a short or leaky component on the rail; a voltage well off 12.600 points to a supply or load problem upstream. No known-good resistance reading is available here, so compare against a matching rail on a known-good board if needed.

PPDCIN_G3H0.56220.000–
AI: what PPDCIN_G3H is and how to check it
  • What it is: PPDCIN_G3H is the DC input rail; the "G3H" suffix indicates an always-on rail, from the name. It's the main power coming in from the charger.
  • Known-good readings: diode 0.562 and voltage 20.000 V, from the readings archive (community-contributed, so a guide only).
  • How to check: with the board unpowered, measure diode mode from PPDCIN_G3H to ground; then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading or missing voltage usually points to a short or a fault in the input path, but confirm with more measurements before replacing anything. No other known-good values are recorded for this rail.
PPDCIN_G3H_CHGR0.56220.000–
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H part of the name indicates it is always-on. Known-good readings here are diode 0.562 to ground and 20.000 V with power applied. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the charger connected. A diode reading far below 0.562 suggests a short or leaky part on the rail; a missing or low voltage points to the charger input path rather than the rail itself. No known-good resistance reading is listed for this rail.

PPDCIN_XA_G3H_F0.56220.000–
AI: what PPDCIN_XA_G3H_F is and how to check it
  • What it is: From its name, PPDCIN_XA_G3H_F is a DC-input rail in the G3H (always-on) domain — the main adapter/DC-in feed that should be present whenever power is connected.
  • Known-good readings (archive, guide only): diode 0.562 to ground, voltage 20.000. No condition is recorded with these values, and there is no known-good resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: A diode reading well below known-good suggests a short or leaky part on the rail; a correct diode reading with no or low voltage points upstream, toward the input path or adapter. These are general guidelines, not confirmed causes.
PPDCIN_XB_G3H_F0.56220.000–
AI: what PPDCIN_XB_G3H_F is and how to check it
  • What it is: From its name, PPDCIN_XB_G3H_F is the DC-in rail on the G3H (always-on) side of the input path — the voltage coming in from the charger before it's switched or regulated further.
  • Known-good readings: diode 0.562 and voltage 20.000 (from the readings archive; treat as a guide, since community readings vary with board state).
  • How to check: with the board unpowered, diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing or low voltage with power applied points to the input/charger path upstream. No known-good resistance reading is listed here, so compare against a matching net or a known-good board.
PPVBAT_G3H_CHGR_R0.33612.650–
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is a battery/charger-related rail; the G3H in its name indicates it is an always-on rail, and CHGR points to the charger side. The archive lists a known-good diode reading of 0.336 and a voltage of 12.650, with no condition noted. Check it unpowered in diode mode to ground, then measure the voltage with power applied. A diode reading far from 0.336 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault. No known-good resistance reading is available here.

PPVBAT_G3H_CHGR_REG0.33612.600–
AI: what PPVBAT_G3H_CHGR_REG is and how to check it
  • What it is: From its name, PPVBAT_G3H_CHGR_REG is the charger-side regulated battery rail that stays present in the always-on G3H state. The board data doesn't list which parts sit on it.
  • Known-good readings (guide only): diode 0.336 to ground, and 12.600 V with power applied. No known-good resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage.
  • If it's far off: A diode reading well below known-good often points to a shorted or leaky part on the rail; a missing or low voltage points to the charger circuit or its supply. Confirm with a second measurement before replacing anything.
PPVBAT_G3H_CONN1.570––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery-connector side of the always-on G3H rail, judged from its name; it is not a switched or main power rail. The only known-good reading in the archive is a diode value of 1.570 to ground, with no condition recorded. Check it unpowered in diode mode from the net to ground, then confirm the voltage with the board powered. No known-good voltage reading is recorded here, so compare against a matching battery-side net or a known-good board. A diode reading far below 1.570 usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a bad part.

PPVIN_G3H_P3V3G3H0.33612.600–
AI: what PPVIN_G3H_P3V3G3H is and how to check it

PPVIN_G3H_P3V3G3H — reference note

  • From the name, this is the G3H (always-on) input rail feeding the 3V3G3H supply; "PPVIN" suggests a main power input, and "P3V3G3H" the always-on 3.3 V rail it feeds. This is inferred from the name only.
  • Known-good readings from the archive: diode 0.336 to ground, voltage 12.600. These are community readings and only a guide; the data gives no condition for them.
  • Check it unpowered in diode mode to ground first, then with power applied measure the voltage.
  • A diode reading far below 0.336 usually points to a short or a leaky part on the rail; a voltage far from 12.600 points to a supply or enable problem upstream. No known-good resistance reading exists here, so compare against a matching net or a known-good board before condemning anything.
PPVIN_G3H_P3V3G3HRTC0.337––
AI: what PPVIN_G3H_P3V3G3HRTC is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V3G3HRTC is a G3H (always-on) input rail feeding the P3V3G3HRTC supply. This is inferred from the rail name, not from a board file.
  • Known-good reading: diode 0.337 to ground, from the readings archive. This is a community value and a guide only; there is no known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.337. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open connection. Confirm with a second measurement before replacing anything.
PPVIN_G3H_P3V3G3HRTC_R0.3373.300–
AI: what PPVIN_G3H_P3V3G3HRTC_R is and how to check it
  • What it is: From its name, PPVIN_G3H_P3V3G3HRTC_R is a 3.3 V rail in the G3H (always-on) domain, so it should be present whenever the board has power, before the main power-on sequence.
  • Known-good readings (community archive, guide only): diode 0.337 to ground, and 3.300 V with power applied. No known-good resistance reading here.
  • How to check: Power off and unplugged, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading or a collapsed voltage usually points to a short or a heavy load on the rail; a missing 3.3 V with a normal diode reading points more toward the supply feeding it. Confirm with a second measurement before replacing anything.
PPVIN_G3H_P5VG3S0.33812.600–
AI: what PPVIN_G3H_P5VG3S is and how to check it
  • What it is: From the name, PPVIN_G3H_P5VG3S is the input supply for the always-on G3H rail (the "G3H" part means always on). The P5VG3S suffix suggests it feeds the 5 V G3S side.
  • Known-good readings (community guide): diode 0.338 to ground, and 12.600 V with power applied.
  • How to check: Power off, then in diode mode measure from the rail to ground; that should read near 0.338. Then power up and measure the voltage, expecting about 12.600 V.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a correct diode reading but missing or low voltage points upstream, toward the supply feeding it. No known-good resistance reading is available here, so compare against a matching net or a known-good board.

S5 and SUS: standby 5

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V05_S5_PCH_VCCDSW0.514––
AI: what PP1V05_S5_PCH_VCCDSW is and how to check it

PP1V05_S5_PCH_VCCDSW is a 1.05 V standby rail feeding the PCH's VCCDSW domain, judged from the name (S5/SUS means it should be present in standby). The archive lists one known-good diode reading of 0.514 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.514 suggests a short or leaky part on the rail, but a single reading isn't proof — confirm with voltage and compare against a matching rail before replacing anything.

PP1V8_S50.314––
AI: what PP1V8_S5 is and how to check it

PP1V8_S5 is a 1.8 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, so it should be present before the board fully powers on. The only known-good figure here is a diode reading of 0.314 to ground, with no condition recorded. Check it with the board unpowered in diode mode from PP1V8_S5 to ground, then apply power and measure the voltage. No known-good voltage reading is recorded for this rail, so compare against a known-good board or matching rail. A diode reading far from 0.314 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP1V24_S5_PCH_VCCDPHY0.414––
AI: what PP1V24_S5_PCH_VCCDPHY is and how to check it

PP1V24_S5_PCH_VCCDPHY is a 1.24 V standby rail feeding the PCH's display PHY section; the S5 and VCCDPHY parts of the name say that, and it's general naming, not from board data. The archive lists one known-good diode reading of 0.414 to ground, with no condition recorded, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far below 0.414 usually points to a short or a leaky load on the rail; a voltage that's missing or low with a normal diode reading points upstream, at the rail's source or its enable. Treat the 0.414 as a guide only, since community readings vary with board state.

PP3V3_S50.379––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the board fully powers on. The only known-good reading in the archive is a diode value of 0.379 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from PP3V3_S5 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.379 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PPVPCORE_S50.2991.000–
AI: what PPVPCORE_S5 is and how to check it

PPVPCORE_S5 is a standby-stage rail on the 820-01987; the S5/SUS suffix in its name indicates standby. The archive lists a known-good diode reading of 0.299 and a voltage of 1.000, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.299 usually points to a short or a damaged component on that rail; no known-good resistance reading is recorded here.

S4 18

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP_SSD0_S4E0_VPP0.569––
AI: what PP_SSD0_S4E0_VPP is and how to check it

PP_SSD0_S4E0_VPP is an SSD-related rail; the "S4" in its name marks it as a sleep-state rail, and "VPP" usually means a programming/boost supply for the SSD (that part is general naming, not from this board's data). The only known-good reading here is a diode value of 0.569 to ground, with no stated condition. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.569 usually points to a short or an open on that rail, but one reading alone doesn't confirm a bad part.

PP_SSD0_S4E1_VPP0.602––
AI: what PP_SSD0_S4E1_VPP is and how to check it
  • What it is: From its name, PP_SSD0_S4E1_VPP is a power rail feeding the SSD's VPP supply, enabled in the S4 startup stage. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.602 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.602. Then apply power and measure the rail's voltage; the data has no known-good voltage to compare against, so use a known-good board or the rail's expected level.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. Confirm with a second measurement before replacing anything.
PP_SSD0_S4E2_VPP0.602––
AI: what PP_SSD0_S4E2_VPP is and how to check it
  • What it is: From its name, PP_SSD0_S4E2_VPP is a power rail (PP) for the SSD, in the S4 startup stage, and the VPP suffix usually means a higher programming/supply voltage for the SSD's flash. General naming, not confirmed by board data.
  • Known-good reading: diode 0.602 to ground, from the readings archive. This is a community guide and varies with board state; no known-good voltage reading here.
  • How to check: power off and unplugged, measure diode mode from the rail to ground and compare with 0.602. Then power on and measure the voltage on the rail.
  • If it's far off: a much lower diode reading or a short to ground usually points to a failed part on that rail or its load; a much higher or open reading points to a broken feed. Confirm with the voltage measurement before replacing anything.
PP_SSD0_S4E3_VPP0.603––
AI: what PP_SSD0_S4E3_VPP is and how to check it
  • What it is: PP_SSD0_S4E3_VPP is an SSD-related rail; the S4 in the name marks it as a stage-4 (S4) startup rail, and VPP suggests a programming/supply voltage for the SSD side. That reading is from the name only, not from a schematic.
  • Known-good: diode-to-ground 0.603 (community archive, guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power on and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or a leaky part on that rail; a much higher one to an open trace or missing part. Confirm with a second measurement before replacing anything.
PP0V9_SSD0_S4E0_VDD_PLL0.368––
AI: what PP0V9_SSD0_S4E0_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail (PP0V9) for the SSD's PLL supply (VDD_PLL), in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.368 in diode mode to ground, board unpowered. No known-good voltage or resistance reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.368. Then power on into S4 and measure the voltage; it should sit near 0.9 V, though that figure comes from the rail name, not the data.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Either way, confirm with a second measurement before replacing anything.
PP0V9_SSD0_S4E1_VDD_PLL0.366––
AI: what PP0V9_SSD0_S4E1_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail feeding the SSD's PLL (VDD_PLL) in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.366 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open feed. Confirm with voltage before replacing anything.
PP0V9_SSD0_S4E2_VDD_PLL0.380––
AI: what PP0V9_SSD0_S4E2_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail (PP0V9) feeding the SSD's PLL supply (VDD_PLL), in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good: diode reading 0.380 in the readings archive; no known-good voltage reading here.
  • How to check: Power off, then measure diode mode from the rail to ground. Then power up and measure the voltage at the rail.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a missing voltage points to the rail not being enabled or its source failing. Treat the 0.380 as a guide only, since readings vary with board state.
PP0V9_SSD0_S4E3_VDD_PLL0.380––
AI: what PP0V9_SSD0_S4E3_VDD_PLL is and how to check it
  • What it is: From its name, PP0V9_SSD0_S4E3_VDD_PLL is a 0.9 V rail feeding the SSD's PLL supply, active in the S4 stage. The board data has no part list, so which components sit on it isn't known.
  • Known-good reading: diode 0.380 to ground, from the community archive — a guide only, since readings vary with board state. No known-good voltage reading here.
  • How to check: power off, then diode mode from the rail to ground; then power on and measure the DC voltage, expecting about 0.9 V per the name.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; an open or high reading suggests a broken feed. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E0_AVDD18_PLL0.359––
AI: what PP1V8_SSD0_S4E0_AVDD18_PLL is and how to check it
  • What it is: From its name, PP1V8_SSD0_S4E0_AVDD18_PLL is a 1.8 V rail feeding the SSD's AVDD18 PLL supply, enabled in the S4 power state.
  • Known-good reading: diode 0.359 in the readings archive. That's a community guide, not a factory spec; no known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up into S4 and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing load on the rail, and a missing voltage points to the rail not being enabled or its source not coming up. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E0_PCI_AVDD_H0.359––
AI: what PP1V8_SSD0_S4E0_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail (PP1V8) for SSD0, in the S4 startup stage, feeding PCI AVDD. The name suggests an SSD/PCIe supply, but which parts sit on it isn't known here.
  • Known-good reading: diode 0.359 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.359. Then power up and measure the voltage; expect about 1.8 V, though that figure is general and not from this board's data.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; an open or high reading points to a missing feed. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E1_AVDD18_PLL0.359––
AI: what PP1V8_SSD0_S4E1_AVDD18_PLL is and how to check it
  • What it is: From the name, a 1.8 V rail (PP1V8) for the SSD0 section, in the S4 power state, feeding an AVDD18 PLL supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.359 to ground, from the readings archive (a community guide, not a guaranteed value). No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the rail to ground; then power on and measure the voltage, expecting about 1.8 V from the name.
  • If it reads far off: a much lower diode reading or a collapsed voltage usually points to a short or a failed load on the rail, but confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E1_PCI_AVDD_H0.359––
AI: what PP1V8_SSD0_S4E1_PCI_AVDD_H is and how to check it
  • What it is: From the name, a 1.8 V rail (PP1V8) for SSD0, in the S4 startup stage, feeding a PCIe AVDD supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.359 in diode mode to ground, board unpowered. That's the only known-good value here; there's no known-good voltage or resistance reading.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.359. Then apply power and measure the rail voltage; the data gives no expected voltage, so compare against a matching rail on a known-good board.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail, and a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP1V8_SSD0_S4E2_AVDD18_PLL0.363––
AI: what PP1V8_SSD0_S4E2_AVDD18_PLL is and how to check it
  • What it is: From the name, a 1.8 V rail for the SSD's PLL analog supply, active in the S4 power state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.363 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on into S4 and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail; a much higher one to an open path. Confirm with voltage before replacing anything.
PP1V8_SSD0_S4E2_PCI_AVDD_H0.363––
AI: what PP1V8_SSD0_S4E2_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail (PP1V8) feeding SSD0 and PCIe AVDD, in the S4 startup stage. That's from the name only; the parts on it aren't known here.
  • Known-good reading: diode 0.363 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode to ground on the rail; then power on and measure the voltage, expecting about 1.8 V.
  • If far off: a much lower diode reading usually points to a shorted load on the rail; a much higher one to an open trace or missing part. Confirm with a voltage check before replacing anything.
PP1V8_SSD0_S4E3_AVDD18_PLL0.360––
AI: what PP1V8_SSD0_S4E3_AVDD18_PLL is and how to check it
  • What it is: From its name, PP1V8_SSD0_S4E3_AVDD18_PLL is a 1.8 V rail feeding the SSD0 section, an AVDD18 supply and a PLL, in the S4 startup stage. It's a general reading of the name, not from board data.
  • Known-good reading: diode 0.360 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. A missing or wrong voltage with a normal diode reading points to the supply or enable side rather than the rail itself. These are guides from community readings, not confirmed faults.
PP1V8_SSD0_S4E3_PCI_AVDD_H0.363––
AI: what PP1V8_SSD0_S4E3_PCI_AVDD_H is and how to check it
  • What it is: From its name, a 1.8 V rail (PP1V8) feeding SSD0 and PCIe AVDD, in the S4 startup stage. The board data doesn't list which parts sit on it.
  • Known-good: Diode-to-ground reading of 0.363 in the readings archive (a community guide, not a spec). No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground, then power on and measure the voltage at the rail.
  • If far off: A much lower diode reading usually points to a short or a failed part on the rail; a missing voltage points to the rail not being enabled or its source not coming up. Confirm with a second reading before replacing anything.
PP3V3_S4SW_SNS0.541––
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS is a 3.3 V rail switched on at the S4 stage of startup, judged from the name; the data doesn't list which parts sit on it. The only known-good reading here is a diode value of 0.541 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.541 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP5V_S4SWOL––
AI: what PP5V_S4SW is and how to check it

PP5V_S4SW is a 5 V switch rail in the S4 startup stage, from its name; the S4 stage generally comes up after the always-on rails in the power sequence (general repair knowledge, not from this board's data).

  • Known-good reading here: diode mode to ground OL, with the board unpowered.
  • No known-good voltage reading is recorded for this rail.
  • To check it: power off, measure diode mode from PP5V_S4SW to ground, then power on and measure the voltage.
  • A diode reading far below OL usually points to a short or a leaky load on the rail; confirm with a second measurement before replacing anything.

S3: memory 9

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.378––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it

PP0V6_S3_MEM_VREFCA_A is a 0.6 V memory reference rail; the S3 in its name indicates it belongs to the memory stage of the power sequence (from the name, not from a schematic). The archive lists one known-good reading: diode 0.378 to ground, with no condition noted. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage, which should sit near 0.6 V. No known-good voltage reading is recorded here, so compare against a matching memory reference net or a known-good board. A diode reading far from 0.378 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PP0V6_S3_MEM_VREFDQ_A0.380––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A — reference note

  • From its name, this is the 0.6 V memory reference rail (VREFDQ) for the S3 memory stage; the "A" suffix marks one of a pair of similar rails.
  • Known-good from the readings archive: diode 0.380 to ground in diode mode. That is the only known-good value recorded here — no known-good voltage or resistance reading.
  • To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the DC voltage; the name suggests it should sit near 0.6 V, but that is general expectation, not a recorded value.
  • A diode reading far from 0.380 points to a short or a damaged part on the rail, or an open feed; a voltage far off 0.6 V points to the rail's source or its load. Confirm with a second measurement before replacing anything.
PP0V6_S3_MEM_VREFDQ_B0.378––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it
  • What it is: From its name, PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail (VREFDQ) that comes up at the S3 (memory) stage. The "_B" suffix usually marks a second or alternate version of the rail; that's general naming, not from this board's data.
  • Known-good reading: diode 0.378 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: Power off, discharge, then diode mode from the rail to ground and compare with 0.378. Then power on and measure the DC voltage, which should sit near 0.6 V by the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. One reading alone doesn't condemn a part, so confirm with the voltage measurement before replacing anything.
PP1V_S30.229––
AI: what PP1V_S3 is and how to check it
  • PP1V_S3 is a 1 V rail in the S3 (memory) startup stage, judged from the rail name; the archive doesn't list which parts sit on it.
  • Known-good: diode reading 0.229 to ground. No known-good voltage reading here.
  • Check with the board unpowered: multimeter in diode mode, black probe on ground, red on PP1V_S3. Then power up and measure the voltage.
  • A diode reading far from 0.229 usually points to a short or a leaky part on that rail; confirm with a voltage check before replacing anything.
PP1V2_S30.2241.200–
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V rail; the S3 suffix in its name points to the memory stage of the power sequence (general naming convention, not board data). Known-good readings here are diode 0.224 and voltage 1.200, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.224 suggests a short or leaky load on the rail; a voltage well off 1.200 points to the rail not coming up or being loaded down. No known-good resistance reading exists for this rail.

PP1V2_S3_CPUDDR0.219––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is a 1.2 V memory rail; the S3 part of the name suggests it comes up in the memory stage of startup, and the CPUDDR part that it feeds the CPU's DDR memory supply (from the name, not from a schematic).

  • Known-good reading in the archive: diode 0.219 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode, black probe on ground, red on the rail; then power the board and measure the voltage at the rail.
  • A diode reading far from 0.219 usually points to a short or a leaky part on that rail, but one reading alone isn't proof — compare against a matching rail or a known-good board before replacing anything.
PP1V2_S3_REG_R0.2241.200–
AI: what PP1V2_S3_REG_R is and how to check it

PP1V2_S3_REG_R is a 1.2 V rail; the S3 in its name marks it as a memory-stage supply, and REG suggests it comes from a regulator (both from the name only). The archive lists diode 0.224 and voltage 1.200, with no condition noted, so treat these as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.224 suggests a short or leaky load on the rail; a voltage well off 1.200 points to the regulator or its feedback. No known-good resistance reading is recorded here.

PP1V8_S30.466––
AI: what PP1V8_S3 is and how to check it

PP1V8_S3 is a 1.8 V rail; the S3 suffix, from its name, places it in the memory stage of startup. The only known-good reading here is a diode value of 0.466 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.466 usually points to a short or a leaky load on the rail, but one reading isn't proof a part is bad — compare against a matching rail or a known-good board before replacing anything.

PP1V8_S3_MEM0.466––
AI: what PP1V8_S3_MEM is and how to check it

PP1V8_S3_MEM is a 1.8 V memory rail that comes up in the S3 (suspend-to-RAM) power state, judging from its name. The only known-good figure here is a diode reading of 0.466 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S3. A diode value far below 0.466 suggests a short or a leaky load on the rail; a value far above can mean an open trace or missing connection. Treat the 0.466 as a guide only, since community readings vary with board state.

S0: running 28

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.137––
AI: what PP0V6_S0_DDRVTT is and how to check it
  • What it is: From the name, PP0V6_S0_DDRVTT is a 0.6 V rail (PP0V6) that runs in the S0 (running) state and is the DDR termination voltage (DDRVTT). It's a low-voltage rail, so treat it as a supply to check, not a main power rail.
  • Known-good reading: The archive lists a diode reading of 0.137 to ground for this net. No known-good voltage reading is recorded here, so compare the powered voltage against a known-good board or the rail's expected 0.6 V.
  • How to check: With the board unpowered, measure diode mode from PP0V6_S0_DDRVTT to ground and compare with 0.137. Then apply power, let the board reach S0, and measure the DC voltage on the rail.
  • What a bad reading suggests: A diode value far below 0.137 usually points to a short or a leaky part on the rail; a value far above can mean an open trace or missing component. A voltage that's absent or well off 0.6 V in S0 points to the rail's source or its enable, not necessarily the load. These are guides only, and a single reading doesn't confirm a bad part.
PP0V95_S0_CPUVCCIO_REG_R0.1240.950–
AI: what PP0V95_S0_CPUVCCIO_REG_R is and how to check it
  • What it is: From the name, a 0.95 V S0 (running-state) CPU VCCIO rail, regulator output side. It's a low-voltage rail, so treat it as a supply to check, not a main power input.
  • Known-good readings (community archive, guide only): diode 0.124 to ground and 0.950 V with the board running. No known-good resistance reading here.
  • How to check: Power off and unplugged, diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; correct diode but missing or wrong voltage points at the regulator's enable, feedback or supply. One reading isn't proof a part is bad — confirm with a second measurement before replacing anything.
PP1V_S0SW0.223––
AI: what PP1V_S0SW is and how to check it
  • PP1V_S0SW is a 1 V rail in the S0 (running) state, inferred from the name; the data doesn't say which parts sit on it.
  • Known-good: diode 0.223 to ground. No known-good voltage or resistance reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far from 0.223 usually points to a short or a leaky part on that rail; confirm with a second reading before replacing anything.
PP1V2_S0SW0.304––
AI: what PP1V2_S0SW is and how to check it

PP1V2_S0SW is a 1.2 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "SW" suggests a switched rail. The only known-good figure here is a diode reading of 0.304 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.304 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP1V8_S0_THMSNSA_R0.316––
AI: what PP1V8_S0_THMSNSA_R is and how to check it
  • What it is: From its name, PP1V8_S0_THMSNSA_R is a 1.8 V rail that runs in the S0 (running) state, likely a thermal-sensor related supply. The board data has no part or net membership for it.
  • Known-good reading: diode 0.316 (from the readings archive; a community guide, not a guaranteed value). No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.316. Then apply power and confirm the rail sits near 1.8 V in the S0 state.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open feed. Confirm with a voltage check before replacing anything.
PP1V8_S0_THMSNSB_R0.314––
AI: what PP1V8_S0_THMSNSB_R is and how to check it
  • What it is: From the name, a 1.8 V S0 (running-state) rail, likely a thermal-sensor related supply; the exact parts on it aren't known here.
  • Known-good reading: diode 0.314 in diode mode (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode to ground on PP1V8_S0_THMSNSB_R; then power on and measure its voltage.
  • If far off: a low diode or low voltage usually points to a shorted load or failed source on that rail, but confirm with a second measurement before replacing anything.
PP3V3_S0_TBT_X_ISNS_R0.527––
AI: what PP3V3_S0_TBT_X_ISNS_R is and how to check it
  • What it is: From the name, a 3.3 V S0 (running-state) rail associated with Thunderbolt current sensing (ISNS). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.527 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • If it's far off: a diode reading well below known-good usually points to a shorted or leaky part on the net; a high or open reading can mean a missing connection. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_LCD0.494––
AI: what PP3V3_S0SW_LCD is and how to check it

PP3V3_S0SW_LCD is the switched 3.3 V LCD rail; the S0 in the name indicates it belongs to the running state, and SW suggests it is switched on by the display section rather than always present. The only known-good figure here is a diode reading of 0.494 to ground, from the readings archive. Check it with the board unpowered in diode mode from the rail to ground, then confirm the voltage with power applied and the display enabled. No known-good voltage reading is recorded for this rail, so compare against a matching rail or a known-good board. A diode reading far from 0.494 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S0SW_LCD_R0.494––
AI: what PP3V3_S0SW_LCD_R is and how to check it

PP3V3_S0SW_LCD_R is a 3.3 V LCD-related rail; the S0 in the name indicates it belongs to the running (S0) power state, and SW suggests it is switched. The only known-good figure here is a diode reading of 0.494 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and the board in S0. A diode reading far from 0.494 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP3V3_TBT_X_S00.528––
AI: what PP3V3_TBT_X_S0 is and how to check it

PP3V3_TBT_X_S0 is the 3.3 V supply for the Thunderbolt section, in the S0 (running) state, judged from the rail name. The only known-good reading here is a diode value of 0.528 to ground, with the board unpowered. Check it in diode mode first, then measure the voltage with the board powered and running. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.528 suggests a short or leak on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S0_BKLT_A0.436––
AI: what PP5V_S0_BKLT_A is and how to check it

PP5V_S0_BKLT_A is the backlight 5 V rail, from its name: the S0 part means it belongs to the running state. The archive gives one known-good reading, diode 0.436, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far from 0.436 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PP5V_S0_BKLT_D0.433––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the backlight rail that runs in the S0 (fully on) state, judging by the name. The archive lists a known-good diode reading of 0.433 to ground, with no condition noted; there's no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.433 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP5V_S0SW_LCD0.572––
AI: what PP5V_S0SW_LCD is and how to check it

PP5V_S0SW_LCD is the switched 5 V LCD rail; from the name it is a 5 V supply gated on in the S0 (running) state. The only known-good reading here is diode mode 0.572 to ground, with no condition recorded; no known-good voltage reading is available. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and the display connected. A diode reading far below 0.572 suggests a short or leaky load on the rail; a missing or low voltage points to the switch or enable side rather than the rail itself.

PP5V_S0SW_LCD_R0.572––
AI: what PP5V_S0SW_LCD_R is and how to check it

PP5V_S0SW_LCD_R is a switched 5 V LCD rail; the S0 in the name indicates it belongs to the running state, and SW suggests it is switched on rather than always present. The only known-good figure here is a diode reading of 0.572 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.572 usually points to a short or a failing load on the rail, while a much higher one can mean an open path; confirm with a second measurement before suspecting any part.

PPVCC_S0_CPU0.0061.5005.200R
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail; the S0 in the name indicates the running state. Known-good readings in the archive: diode 0.006, voltage 1.500, resistance 5.200R (community values, a guide only). Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.006 usually points to a short or a failed component on the rail, but a single reading doesn't confirm a bad part. No known-good waveform or current reading here.

PPVCCEDRAM_S0_CPU0.0471.000–
AI: what PPVCCEDRAM_S0_CPU is and how to check it

PPVCCEDRAM_S0_CPU — reference note

  • This is the CPU-side EDRAM supply rail; the "S0" in the name marks it as a running-state rail (from the name, not from a schematic).
  • Known-good from the archive: diode 0.047 to ground and 1.000 V with the board powered. These are community readings and only a guide.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A diode reading far from 0.047 suggests a short or leaky load on the rail; a missing or wrong voltage with a normal diode reading points upstream at the rail's source or its enable. No known-good resistance reading exists for this rail.
PPVCCEDRAM_S0_REG_R0.0471.00047.500R
AI: what PPVCCEDRAM_S0_REG_R is and how to check it

PPVCCEDRAM_S0_REG_R is a running-state (S0, from the name) regulated supply for the eDRAM, likely a memory rail. Known-good readings here: diode 0.047, voltage 1.000, resistance 47.500R. Check it unpowered in diode mode to ground, then measure the voltage with the board powered. A reading far from these usually points to a short or a failed regulator on that rail, but one reading alone doesn't confirm a bad part.

PPVCCGT_S0_CPU0.0061.5005.100R
AI: what PPVCCGT_S0_CPU is and how to check it

PPVCCGT_S0_CPU — the name indicates a CPU graphics rail (VCCGT), in the S0 (running) power state. It is a low-voltage, high-current rail, so a low diode reading to ground is expected.

  • Known-good readings in the archive: diode 0.006, voltage 1.500, resistance 5.100R. These are community readings and vary with board state, so treat them as a guide only.
  • Check with the board unpowered: diode mode from the rail to ground, then resistance to ground. Then apply power and measure the voltage.
  • A reading far from known-good — much higher resistance or an open diode — usually points to a broken feed, a bad inductor or shunt, or a rail that isn't being enabled. A near-short with the voltage missing points the other way, toward a shorted load.
  • No known-good value exists here for current draw or ripple; compare against a matching rail or a known-good board.
PPVCCIO_S0_CPU0.1240.950–
AI: what PPVCCIO_S0_CPU is and how to check it
  • What it is: PPVCCIO_S0_CPU is a CPU I/O supply rail; the S0 in the name indicates it's up in the running state (from the name, not from board data).
  • Known-good readings (community archive, guide only): diode 0.124 to ground, and 0.950 V with power applied.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail, while missing or wrong voltage with a normal diode reading points to the supply not coming up. No known-good resistance reading is available here, so compare against a matching rail or a known-good board.
PPVCCSA_S0_CPU0.0231.15023.000R
AI: what PPVCCSA_S0_CPU is and how to check it

PPVCCSA_S0_CPU — reference note

  • What it is: From the name, this is the CPU's system-agent supply rail (VCCSA), enabled in the S0 running state. It is a low-voltage CPU rail, not a main power rail.
  • Known-good readings (community archive, guide only): diode 0.023, voltage 1.150 V, resistance 23.000R. These are the only known-good values recorded here; there is no separate condition noted.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage on the rail. Compare both against the figures above.
  • If far off: A diode or resistance reading well below known-good usually points to a short or a failing load on the rail; a correct diode reading with no or wrong voltage points back to the rail's supply circuit. A single reading is not proof of a bad part — confirm with a second measurement before replacing anything.
PPVIN_S0_CPUVR_VIN0.344––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it
  • What it is: From the name, PPVIN_S0_CPUVR_VIN is the input supply to the CPU voltage-regulator stage, active in the S0 (running) state. The data doesn't list which parts sit on it.
  • Known-good reading: diode 0.344 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then diode-mode from the rail to ground; then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open feed or missing source. Confirm with a voltage check before replacing anything.
PPVIN_S0SW_LCDBKLT0.899–0.573R
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT — 820-01987

  • From its name, this is the switched input supply for the LCD backlight, active in the S0 (running) state. It is the feed into the backlight boost circuit, not the boosted backlight output itself.
  • Known-good readings from the archive: diode 0.899 and resistance 0.573R. No known-good voltage reading is recorded here.
  • To check it, power the board off and measure diode mode to ground on the rail; then apply power and measure the voltage present in the S0 state.
  • A diode or resistance far below known-good usually points to a short or a leaky component on the rail; a voltage that is missing or low when the board should be running points upstream to the switch or its enable.
PPVIN_S0SW_LCDBKLT_F0.33612.600–
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT_F is the input supply for the LCD backlight switch, active in the S0 (running) state. The data doesn't list which parts sit on it.
  • Known-good readings: diode 0.336 and voltage 12.600, from the community archive, so treat them as a guide only.
  • How to check: With the board unpowered, diode mode from the rail to ground and compare with 0.336; then power up and measure the voltage, expecting around 12.6 V when the rail is up.
  • If far off: A diode reading well below known-good often points to a short or leaky part on the rail; no voltage where 12.6 V is expected points to the supply or enable side. No known-good resistance reading here, so compare against a matching net or a known-good board.
PPVIN_S0SW_LCDBKLT_R0.33612.600–
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the backlight input rail; the S0SW part of the name suggests it is switched in the running (S0) state, and LCDBKLT marks it as the display backlight supply (from the name).

  • Known-good readings in the archive: diode 0.336 to ground, and 12.600 V with power applied. These are community readings and only a guide.
  • Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage.
  • A diode reading well below 0.336 suggests a short or leaky load on the rail; a voltage far from 12.600 V with the board running points to the backlight supply or its switching not coming up.
  • No known-good resistance reading is recorded for this rail.
PPVOUT_S0_KBDLED0.634––
AI: what PPVOUT_S0_KBDLED is and how to check it

PPVOUT_S0_KBDLED is the keyboard backlight power rail; the S0 in the name indicates it belongs to the running state, and the KBDLED part points to the keyboard LEDs. The only known-good reading here is a diode value of 0.634, with no condition recorded and no known-good voltage or resistance value. Check it with the board unpowered in diode mode from the rail to ground, then measure its voltage with the board powered and running. A diode reading far from 0.634 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPVOUT_S0_KBDLED_R0.63540.000–
AI: what PPVOUT_S0_KBDLED_R is and how to check it
  • What it is: From its name, PPVOUT_S0_KBDLED_R is a switched power output (PPVOUT) for the keyboard backlight LED rail, active in the S0 (running) state. The "_R" suffix usually marks a related or secondary rail of the same output.
  • Known-good readings (community archive, a guide only): diode 0.635 to ground, voltage 40.000. No known-good resistance value is recorded here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • What a far-off reading suggests: A diode reading well below known-good often points to a short or leaky component on the rail; a missing or wrong voltage with power applied points to the supply or enable side. Treat these as likely causes, not confirmed, and compare against a matching rail before replacing anything.
PPVOUT_S0_LCDBKLT1.250––
AI: what PPVOUT_S0_LCDBKLT is and how to check it
  • What it is: From the name, PPVOUT_S0_LCDBKLT is the LCD backlight output rail, active in the S0 (running) state. It's the boost-converter output that drives the display backlight.
  • Known-good reading: diode 1.250 to ground, from the readings archive (community value, a guide only, not a confirmed spec). No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 1.250. Then apply power and measure the rail's voltage.
  • If it's far off: A diode reading well below known-good usually points to a short or leaky part on the rail; a much higher or open reading points to a broken trace or missing part. Confirm with a voltage check before replacing anything.
PPVOUT_S0_LCDBKLT_F1.25646.000–
AI: what PPVOUT_S0_LCDBKLT_F is and how to check it
  • What it is: From the name, PPVOUT_S0_LCDBKLT_F is the display backlight output rail, active in the S0 (running) state. It's a boosted supply, so it normally sits well above the main battery/input voltage.
  • Known-good readings (community guide): diode 1.256 to ground, voltage 46.000. No known-good resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • What a far-off reading suggests: A very low diode reading points to a short on the rail, often the backlight output stage or a shorted capacitor; a missing or low voltage with a normal diode reading points upstream to the backlight boost circuit or its enable. These are likely causes, not confirmed ones.

Every net with a reading

NetDiodeVoltageResistance
1V8_SWCH_EN0.760––
1V8_SWCH_SLEWOL––
50_ANT_C0OL––
50_ANT_C1OL––
ACT_GND0.000––
ADC2_REFCOMPOL––
ALL_SYS_PWRGD0.709––
ALL_SYS_PWRGD_R0.488––
AON_SLEEP1_RESET_L0.420––
AUD_CONN_HP_LEFT0.718––
AUD_CONN_HP_RIGHT0.718––
AUD_CONN_HP_SENSE_L1.362––
AUD_CONN_HP_SENSE_R1.359––
AUD_CONN_RING_SENSE0.644––
AUD_CONN_RING20.002–1.700R
AUD_CONN_RING2_XW0.632––
AUD_CONN_SLEEVE0.002–1.800R
AUD_CONN_SLEEVE_XW0.632––
AUD_CONN_TIP_SENSE1.475––
AUD_DMIC0_DATA_CONN0.550––
AUD_DMIC1_DATA_CONN0.549––
AUD_HP_PORT_CH_GND0.002––
AUD_HP_PORT_L0.718––
AUD_HP_PORT_R0.718––
AUD_HP_PORT_US_GND0.002––
AUD_HP_SENSE_L1.362––
AUD_HP_SENSE_R1.359––
AUD_HS_MIC_N0.632––
AUD_HS_MIC_P0.632––
AUD_RING_SENSE0.644––
AUD_TIP_SENSE1.475––
BKLT_EN_R0.559––
BKLT_ISET_KEYB0.680––
BKLT_KEYB10.662––
BKLT_KEYB20.657––
BKLT_PWM_KEYB_3V30.531––
BKLT_SCL0.555––
BKLT_SD0.603––
BKLT_SDA0.555––
BKLT_SENSE_OUT0.733––
BOARD_REV00.473––
BOARD_REV10.477––
BOARD_REV20.474––
BOOT_CONFIG00.478––
BOOT_CONFIG10.476––
BOOT_CONFIG20.477––
BT_AUDIO_SYNC0.632––
BT_GPIO_40.562––
BT_SFLASH_CS_L0.696––
BT_SFLASH_HOLD_L0.466––
BT_SFLASH_WP_L0.463––
BT_SPI2_CLK0.471––
BT_SPI2_CSN0.635––
BT_SPI2_MISO0.459––
BT_SPI2_MOSI0.460––
CAPSLOCK_LED_EN0.528––
CATERR_LED_AOL––
CATERR_LED_GOL––
CATERR_LED_KOL––
CHGR_AMON0.635––
CHGR_AUX_DET0.641––
CHGR_BGATE0.635––
CHGR_BMON0.635––
CHGR_BOOT10.589––
CHGR_BOOT1_RC0.595––
CHGR_BOOT20.585––
CHGR_BOOT2_RC0.585––
CHGR_COMP0.639––
CHGR_CSI_N0.557––
CHGR_CSI_P0.558––
CHGR_CSI_R_N0.562––
CHGR_CSI_R_P0.562––
CHGR_CSO_N0.339––
CHGR_CSO_P0.340––
CHGR_CSO_R_N0.33612.650–
CHGR_CSO_R_P0.33612.650–
CHGR_EN_MVR0.615––
CHGR_EN_MVR_R0.613––
CHGR_GATE_Q10.855––
CHGR_GATE_Q20.480––
CHGR_GATE_Q30.472––
CHGR_GATE_Q40.852––
CHGR_LX10.37712.6000.135R
CHGR_LX20.37712.6000.135R
CHGR_RST_IN0.632––
CHGR_RST_IN_R0.694––
CHGR_VBAT0.635––
CHGR_VDDA0.468––
CHGR_VDDP0.466––
CODEC_INT_L0.478––
CODEC_RESET_L0.475––
CODEC_WAKE_L0.471––
COMP_A_CPUGT0.634––
COMP_A_CPUGT_LOL––
COMP_B_CPUCORE0.635––
COMP_B_CPUCORE_LOL––
COMP_C_CPUSA0.635––
COMP_C_CPUSA_LOL––
CORE_ISUMN_R1.015––
CPU_C10_GATE_L0.482––
CPU_CATERR_L0.241––
CPU_CFG_RCOMP0.053–50.400R
CPU_CFG<3>0.290––
CPU_CFG<4>0.275––
CPU_CFG<5>0.291––
CPU_CFG<7>0.290––
CPU_CFG<10>0.290––
CPU_CFG<16>0.292––
CPU_DDDR0_ALERT_L0.001–0.600R
CPU_DDDR1_ALERT_L0.001–0.600R
CPU_DDR_RCOMP<0>0.197––
CPU_DDR_RCOMP<1>0.085–81.600R
CPU_DDR_RCOMP<2>0.164––
CPU_DIMM_VREFCA0.382––
CPU_DIMMA_VREFDQ0.390––
CPU_DIMMB_VREFDQ0.387––
CPU_DRAM_RESET_L0.600––
CPU_INPUT3VSEL0.827––
CPU_IST_TRIG0.340––
CPU_PECI0.286––
CPU_PECI_R0.297––
CPU_PROCHOT_L0.456––
CPU_PROCHOT_OUT_L0.481––
CPU_PROCHOT_R_L0.290––
CPU_SMC_THRMTRIP_L0.468––
CPU_VCCEOPIOSENSE_N0.004–1.200R
CPU_VCCEOPIOSENSE_P0.048–44.200R
CPU_VCCEOPIOSENSE_R0.058–56.700R
CPU_VCCEOPIOSENSE_XW0.004–2.600R
CPU_VCCGTSENSE_N0.002–1.500R
CPU_VCCGTSENSE_P0.007–5.800R
CPU_VCCIOSENSE_N0.000–1.600R
CPU_VCCIOSENSE_P0.117––
CPU_VCCIOSENSE_R0.192––
CPU_VCCIOSENSE_XW0.002–1.600R
CPU_VCCSASENSE_N0.005–2.900R
CPU_VCCSASENSE_P0.025–22.800R
CPU_VCCSENSE_N0.003–1.100R
CPU_VCCSENSE_P0.008–6.100R
CPU_VCCST_PWRGD0.515––
CPU_VCCST_PWRGD_R0.537––
CPU_VIDALERT_L0.286––
CPU_VIDALERT_R_L0.240––
CPU_VIDSCLK0.239––
CPU_VIDSCLK_R0.240––
CPU_VIDSOUT0.239––
CPU_VIDSOUT_R0.241––
CPU_VR_EN_R0.486––
CPU_VR_PROCHOT_L0.524––
CPU_VR_READY0.592––
CPU_ZVM_L0.379––
CPUCORE_BOOT10.605––
CPUCORE_BOOT20.604––
CPUCORE_BP10.605––
CPUCORE_BP20.604––
CPUCORE_FCCM0.612––
CPUCORE_ISEN10.635––
CPUCORE_ISEN20.635––
CPUCORE_ISNS1_N0.0061.5005.200R
CPUCORE_ISNS1_P0.0061.5005.200R
CPUCORE_ISNS2_N0.0061.5005.200R
CPUCORE_ISNS2_P0.0061.5005.200R
CPUCORE_ISUMN0.006–6.200R
CPUCORE_ISUMN_R0.486––
CPUCORE_ISUMP0.487––
CPUCORE_PHASE10.005–5.300R
CPUCORE_PHASE2––6.800R
CPUCORE_PSYS0.633––
CPUCORE_PWM10.617––
CPUCORE_PWM20.618––
CPUCORE_SW10.006–5.200R
CPUCORE_SW1_SNUBOL––
CPUCORE_SW20.0061.5005.200R
CPUCORE_SW2_SNUBOL––
CPUCORE1_DRVH0.636––
CPUCORE2_DRVH0.637––
CPUDDR_IOUTOL––
CPUGT_BOOT10.605––
CPUGT_BOOT20.607––
CPUGT_BP10.605––
CPUGT_BP20.607––
CPUGT_FCCM0.611––
CPUGT_ISEN10.635––
CPUGT_ISEN20.635––
CPUGT_ISNS1_N0.0061.5005.100R
CPUGT_ISNS1_P0.0061.5005.100R
CPUGT_ISNS2_N0.0061.5005.100R
CPUGT_ISNS2_P0.0061.5005.100R
CPUGT_ISUM_IOUTOL––
CPUGT_ISUMN0.006–5.900R
CPUGT_ISUMN_R0.486––
CPUGT_ISUMP0.486––
CPUGT_PHASE10.006–6.600R
CPUGT_PHASE20.006–6.600R
CPUGT_PWM10.619––
CPUGT_PWM20.619––
CPUGT_SW10.0061.5005.100R
CPUGT_SW1_SNUBOL––
CPUGT_SW20.006–5.100R
CPUGT_SW2_SNUBOL––
CPUGT1_DRVH0.634––
CPUGT1_GL00.462––
CPUGTVSENSE_IN0.005–5.300R
CPUHI_IOUT0.711––
CPUREGMISCP5V_IOUTOL––
CPUSA_BOOTSA0.603––
CPUSA_BPSA0.603––
CPUSA_DRVH0.001–1.300R
CPUSA_FCCM0.619––
CPUSA_GL00.490––
CPUSA_ISNS_N0.031–30.500R
CPUSA_ISNS_P0.031–30.600R
CPUSA_ISNS_R_N0.0231.15023.000R
CPUSA_ISNS_R_P0.0231.15023.000R
CPUSA_ISUMN0.022–21.700R
CPUSA_ISUMN_R0.493––
CPUSA_ISUMP0.584––
CPUSA_PHASESA0.020–20.100R
CPUSA_PWM0.615––
CPUSA_SW_SNUBOL––
CPUSAVSENSE_IN0.020–19.400R
CPUVCCIO_IOUTOL––
CPUVR_ISUM_IOUTOL––
CPUVR_SWSA0.0231.15023.000R
CPUVR_VIDALERT_L_R0.291––
CPUVR_VIDSCLK_R0.302––
CPUVR_VIDSOUT_R0.255––
CPUVSENSE_IN0.007–5.900R
CSI2_COMP0.101––
DBGLED_S0OL––
DBGLED_S0_DOL––
DBGLED_S0I3OL––
DBGLED_S0I3_DOL––
DBGLED_S3OL––
DBGLED_S3_DOL––
DBGLED_S4OL––
DBGLED_S4_DOL––
DDRREG_VTTSNS0.137––
DEBUG_JTAG_SOC_TDI0.472––
DEBUG_JTAG_SOC_TDO0.473––
DFR_DISP_INT0.476––
DFR_DISP_RESET_L0.478––
DFR_DISP_TE0.479––
DFR_DISP_VSYNCOL––
DFR_PWR_EN0.475––
DFR_PWR_EN_R0.557––
DFR_TOUCH_CLK32K_RESET_L0.478––
DFR_TOUCH_INT_L0.472––
DFR_TOUCH_LID_OPEN_LOL––
DFR_TOUCH_RESET_L0.475––
DFR3V3_IOUTOL––
DFUMUX_SELOL––
DP_INT_HPD0.530––
DP_INT_HPD_L0.468––
DP_INT_HPD_MASK0.456––
DP_XA_HPD0.586––
DP_XB_HPD0.590––
EADC2_AD0OL––
EADC2_KBBLT_ISENSEOL––
EADC2_LCDBKLT_ISENSEOL––
EADC2_MESA_ISENSEOL––
EADC2_P3V3_DFR_ISENSEOL––
EADC2_P3V3_KBD_ISENSEOL––
EADC2_P3V3_TPAD_ISENSEOL––
EADC2_P5V_LCD_ISENSEOL––
EADC2_P5V_TPAD_ISENSEOL––
EDP_AUXCH_N0.245––
EDP_AUXCH_P0.247––
EDP_BKLT_EN0.562––
EDP_BKLT_PWM0.818––
EDP_COMP0.139––
EDP_PANEL_PWR_BUF_EN0.716––
EDP_PANEL_PWR_DLY_EN0.708––
EDP_PANEL_PWR_EN0.568––
EEPROM_WC_L0.536––
EMMC_RCOMP0.203––
ENET_CLKREQ_L0.479––
ESPI_CLK60M0.465––
ESPI_CLK60M_DBG0.475––
ESPI_CLK60M_R0.483––
ESPI_CS_L0.462––
ESPI_CS_PCH_L0.474––
ESPI_DBG_CS_LOL––
ESPI_IO_DBG<0>OL––
ESPI_IO_DBG<1>OL––
ESPI_IO_DBG<2>OL––
ESPI_IO_DBG<3>OL––
ESPI_IO_PCH<0>0.490––
ESPI_IO_PCH<1>0.484––
ESPI_IO_PCH<2>0.501––
ESPI_IO_PCH<3>0.488––
ESPI_IO_R<0>0.462––
ESPI_IO_R<1>0.462––
ESPI_IO_R<2>0.462––
ESPI_IO_R<3>0.462––
ESPI_IO<0>0.480––
ESPI_IO<1>0.474––
ESPI_IO<2>0.474––
ESPI_IO<3>0.475––
ESPI_RESET_L0.460––
FAN_RT_PWM0.725––
FAN_RT_TACHOL––
FB_A_CPUGT0.613––
FB_A_GT_R1.616––
FB_A_GT_RC1.331––
FB_B_CORE_R1.621––
FB_B_CORE_RC1.338––
FB_B_CPUCORE0.618––
FB_C_CPUSA0.615––
FB_C_SA_ROL––
FB_C_SA_RCOL––
FB_CORE_R0.008–6.100R
FB_GT_R0.007–6.000R
FB_SA_R0.024––
GT_ISUMN_ROL––
HS_3V3RTC_IOUTOL––
HS_OTHER3V3_IOUTOL––
HS_OTHER5V_IOUTOL––
HW_ID10.552––
I2C_ALS_SCL0.468––
I2C_ALS_SCL_R0.469––
I2C_ALS_SDA0.468––
I2C_ALS_SDA_R0.469––
I2C_BKLT_SCL0.557––
I2C_BKLT_SDA0.557––
I2C_CODEC_SCL0.475––
I2C_CODEC_SDA0.475––
I2C_DFR_SCL0.474––
I2C_DFR_SCL_R0.488––
I2C_DFR_SDA0.474––
I2C_DFR_SDA_R0.488––
I2C_DISP_3V3_SCL0.503––
I2C_DISP_3V3_SDA0.502––
I2C_DISP_LS_EN0.505––
I2C_DISP_SCL0.454––
I2C_DISP_SDA0.452––
I2C_FTCAM_DSBL_SCL0.497––
I2C_FTCAM_DSBL_SDA0.497––
I2C_FTCAM_ISOL_SCL0.498––
I2C_FTCAM_ISOL_SDA0.498––
I2C_FTCAM_SCL0.445––
I2C_FTCAM_SCL_R0.443––
I2C_FTCAM_SDA0.443––
I2C_FTCAM_SDA_R0.443––
I2C_KBD_SCL0.711––
I2C_KBD_SDA0.496––
I2C_PWR_SCL0.469––
I2C_PWR_SCL_R10.470––
I2C_PWR_SCL_R20.470––
I2C_PWR_SDA0.467––
I2C_PWR_SDA_R10.470––
I2C_PWR_SDA_R20.469––
I2C_SENSE_5V_SCLOL––
I2C_SENSE_5V_SCL_R2OL––
I2C_SENSE_5V_SDAOL––
I2C_SENSE_5V_SDA_R2OL––
I2C_SENSE_SCL0.466––
I2C_SENSE_SCL_R10.488––
I2C_SENSE_SCL_R2OL––
I2C_SENSE_SDA0.466––
I2C_SENSE_SDA_R10.488––
I2C_SENSE_SDA_R2OL––
I2C_SEP_SCL0.472––
I2C_SEP_SDA0.470––
I2C_SNS0_S0_SCL0.465––
I2C_SNS0_S0_SDA0.465––
I2C_SPKRAMP_L_SCL0.386––
I2C_SPKRAMP_L_SDA0.386––
I2C_SPKRAMP_R_SCL0.391––
I2C_SPKRAMP_R_SDA0.391––
I2C_SSD_SCL0.467––
I2C_SSD_SDA0.467––
I2C_TBT_X_SCL0.531––
I2C_TBT_X_SDA0.531––
I2C_TBT_XA_INT_L0.588––
I2C_TBT_XB_INT_L0.586––
I2C_THMSNS_SCL0.464––
I2C_THMSNS_SCL_R00.464––
I2C_THMSNS_SCL_R10.466––
I2C_THMSNS_SCL_R20.465––
I2C_THMSNS_SDA0.463––
I2C_THMSNS_SDA_R00.463––
I2C_THMSNS_SDA_R10.465––
I2C_THMSNS_SDA_R20.464––
I2C_TPAD_3V3_SCL0.950––
I2C_TPAD_3V3_SCL_R0.919––
I2C_TPAD_3V3_SDA0.942––
I2C_TPAD_3V3_SDA_R0.912––
I2C_UPC_SCL0.467––
I2C_UPC_SDA0.466––
I2C_UPC_X_SCL20.465––
I2C_UPC_X_SDA20.465––
I2C_UPC_XA_DBG_CTL_SCL0.599––
I2C_UPC_XA_DBG_CTL_SDA0.587––
I2C_UPC_XB_DBG_CTL_SCL0.589––
I2C_UPC_XB_DBG_CTL_SDA0.588––
I2S_CODEC_BCLK0.481––
I2S_CODEC_D2R0.469––
I2S_CODEC_LRCLK_R0.482––
I2S_CODEC_R2D0.458––
I2S_SPKRAMP_L_BCLK0.387––
I2S_SPKRAMP_L_D2R0.376––
I2S_SPKRAMP_L_D2R_R10.387––
I2S_SPKRAMP_L_D2R_R20.387––
I2S_SPKRAMP_L_LRCLK_R0.387––
I2S_SPKRAMP_L_R2D0.389––
I2S_SPKRAMP_R_BCLK0.386––
I2S_SPKRAMP_R_BCLK_R0.378––
I2S_SPKRAMP_R_D2R0.470––
I2S_SPKRAMP_R_D2R_R10.388––
I2S_SPKRAMP_R_D2R_R20.388––
I2S_SPKRAMP_R_LRCLK0.406––
I2S_SPKRAMP_R_LRCLK_R0.384––
I2S_SPKRAMP_R_R2D0.386––
I2S_SPKRAMP_R_R2D_R0.406––
IMON_A_CPUGT0.635––
IMON_B_CPUCORE0.635––
IMON_C_CPUSA0.635––
IOXP_I2C_SCL0.690––
IOXP_I2C_SDA0.469––
IOXP1_INT_L0.646––
IOXP1_RESET_L0.748––
IOXP2_ADDR0.723––
IOXP2_INT_L0.654––
IPD_LID_OPEN0.710––
IPD_LID_OPEN_ROL––
ISNS_CALPE_IOUTOL––
ISNS_CALPE_NOL––
ISNS_CALPE_POL––
ISNS_CPUDDR_N0.224––
ISNS_CPUDDR_P0.224––
ISNS_CPUEDRAM_IOUTOL––
ISNS_CPUEDRAM_N0.054–53.000R
ISNS_CPUEDRAM_P0.054–53.000R
ISNS_CPUGT_NOL––
ISNS_CPUGT_POL––
ISNS_CPUGT_R_NOL––
ISNS_CPUGT_R_POL––
ISNS_CPUSA_IOUTOL––
ISNS_CPUVCCIO_N0.129––
ISNS_CPUVCCIO_P0.129––
ISNS_CPUVDDQ_NOL––
ISNS_CPUVDDQ_POL––
ISNS_CPUVR_NOL––
ISNS_CPUVR_POL––
ISNS_CPUVR_R_NOL––
ISNS_CPUVR_R_POL––
ISNS_DDR_IOUTOL––
ISNS_DFR3V3_NOL––
ISNS_DFR3V3_POL––
ISNS_HS_3V3RTC_NOL––
ISNS_HS_3V3RTC_POL––
ISNS_HS_CPU_N0.33612.600–
ISNS_HS_CPU_P0.33612.600–
ISNS_HS_OTHER3V3_N0.33612.600–
ISNS_HS_OTHER3V3_P0.33612.600–
ISNS_HS_OTHER5V_N0.338––
ISNS_HS_OTHER5V_P0.338––
ISNS_KBBLT_IOUTOL––
ISNS_KBBLT_NOL––
ISNS_KBBLT_POL––
ISNS_KBDP3V3_NOL––
ISNS_KBDP3V3_POL––
ISNS_LCDBKLT_N0.33612.600–
ISNS_LCDBKLT_P0.33612.600–
ISNS_LCDPANEL_NOL––
ISNS_LCDPANEL_POL––
ISNS_MESA_IOUTOL––
ISNS_MESA_NOL––
ISNS_MESA_POL––
ISNS_OCARINA_IOUTOL––
ISNS_OCARINA_NOL––
ISNS_OCARINA_POL––
ISNS_P1V8G3S_NOL––
ISNS_P1V8G3S_POL––
ISNS_P1V8LPDDR_NOL––
ISNS_P1V8LPDDR_POL––
ISNS_P5VCPUREGMISC_NOL––
ISNS_P5VCPUREGMISC_POL––
ISNS_PP5V_LCD_NOL––
ISNS_PP5V_LCD_POL––
ISNS_SPKRAMP_LEFT_NOL––
ISNS_SPKRAMP_LEFT_POL––
ISNS_SPKRAMP_RIGHT_NOL––
ISNS_SPKRAMP_RIGHT_POL––
ISNS_SSDNAND_NOL––
ISNS_SSDNAND_POL––
ISNS_TBTX_N0.000––
ISNS_TBTX_POL––
ISNS_TPADP3V3_NOL––
ISNS_TPADP3V3_POL––
ISNS_TPADP5V_NOL––
ISNS_TPADP5V_POL––
ISNS_WLAN_OPOL––
ISNS_WLANBTP1V8_NOL––
ISNS_WLANBTP1V8_POL––
ISNS_WLANBTP3V3_NOL––
ISNS_WLANBTP3V3_POL––
ISNS_WLANBTP3V3_R_NOL––
ISNS_WLANBTP3V3_R_POL––
ITP_PMODE0.381––
JTAG_ISP_TCK0.586––
JTAG_ISP_TDI0.583––
JTAG_ISP_TDO0.586––
JTAG_TBT_T_TMS0.802––
JTAG_TBT_X_TMS0.583––
KBD_CAP_CATHODE0.505––
KBD_CAPSLOCK_LED0.503––
KBD_CONTROL_KEY0.477––
KBD_CONTROL_L0.463––
KBD_DRIVE_Y00.537––
KBD_DRIVE_Y10.551––
KBD_DRIVE_Y20.545––
KBD_DRIVE_Y30.541––
KBD_DRIVE_Y40.544––
KBD_DRIVE_Y50.536––
KBD_DRIVE_Y60.510––
KBD_DRIVE_Y70.511––
KBD_ID_DETECT10.541––
KBD_ID10.791––
KBD_INT_L0.688––
KBD_LEFT_OPTION_KEY0.476––
KBD_LEFT_OPTION_L0.460––
KBD_RIGHT_SHIFT_KEY0.477––
KBD_RIGHT_SHIFT_L0.460––
KBD_SENSE_X00.574––
KBD_SENSE_X10.582––
KBD_SENSE_X20.577––
KBD_SENSE_X30.571––
KBD_SENSE_X40.590––
KBD_SENSE_X50.583––
KBD_SENSE_X60.523––
KBD_SENSE_X70.520––
KBD_SENSE_X80.522––
KBD_SENSE_X90.526––
KBD_SENSE_X100.573––
KBD_SENSE_X110.586––
KBD_SENSE_X120.583––
KBDBKLT_SW20.4265.000–
KBDP3V3_IOUTOL––
L83_FILT0.803––
L83_FLYC0.393––
L83_FLYN0.464––
L83_FLYP0.407––
L83_HSBIAS_FILT0.720––
L83_HSBIAS_FILT_REF0.639––
L83_SDOUT0.489––
L83_VCP_FILT_GND0.000––
L83_VCP_FILTN0.620––
L83_VCP_FILTP0.397––
LCD_PWR_SLEW0.721––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.731––
LCDBKLT_FET_DRV0.559––
LCDBKLT_FET_DRV_R0.569––
LCDBKLT_IOUTOL––
LCDBKLT_SW0.451––
LCDBKLT_TB_XWR1.240––
LCDP5V_IOUTOL––
LCDPANEL_IOUTOL––
LED_CTRL0.569––
LED_ISET0.581––
LID_OPEN_LEFT0.557––
LID_OPEN_RIGHT0.698––
LPDDRP1V8_IOUTOL––
MEM_VREFCA_RC0.026–25.400R
MEMVTT_EN0.533––
MEMVTT_EN_R0.533––
MESA_BOOST_EN0.529––
MESA_BOOST_EN_CONN0.548––
MESA_INT0.480––
MESA_INT_CONN0.479––
MESA_PWR_EN0.472––
MIPI_DFR_CLK_FILT_CONN_N0.529––
MIPI_DFR_CLK_FILT_CONN_P0.529––
MIPI_DFR_CLK_N0.529––
MIPI_DFR_CLK_P0.529––
MIPI_DFR_DATA_FILT_CONN_N0.528––
MIPI_DFR_DATA_FILT_CONN_P0.528––
MIPI_DFR_DATA_N0.528––
MIPI_DFR_DATA_P0.528––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_N0.498––
MIPI_FTCAM_CLK_ISOL_FILT_CONN_P0.503––
MIPI_FTCAM_CLK_ISOL_N0.497––
MIPI_FTCAM_CLK_ISOL_P0.502––
MIPI_FTCAM_CLK_N0.466––
MIPI_FTCAM_CLK_P0.468––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_N<0>0.502––
MIPI_FTCAM_DATA_ISOL_FILT_CONN_P<0>0.500––
MIPI_FTCAM_DATA_ISOL_N<0>0.498––
MIPI_FTCAM_DATA_ISOL_P<0>0.499––
MIPI_FTCAM_DATA_N<0>0.467––
MIPI_FTCAM_DATA_P<0>0.465––
MLB_RAMCFG00.763––
MLB_RAMCFG10.768––
MLB_RAMCFG20.765––
MLB_RAMCFG30.759––
MLB_RAMCFG40.760––
NFC_GPIO2_AO0.757––
NFC_GPIO3_AO0.759––
NFC_XTAL10.556––
NTC_A_CPUGT0.636––
NTC_A_CPUGT_RN0.001–0.700R
NTC_A_CPUGT_RPOL––
NTC_B_CPUCORE0.637––
NTC_B_CPUCORE_RN0.001–0.700R
NTC_B_CPUCORE_RPOL––
OCARINA_FORCE_EN0.582––
OCARINA_IREF0.752––
OCARINA_NAND_VCC_DET0.759––
OCARINA_PGOOD0.763––
OCARINA_POK20.000––
OCARINA_TCAL0.773––
OCARINA_TDEV10.772––
OCARINA_TDEV20.772––
OCARINA_VDD_LDO0.371––
OCARINA_VREF0.770––
OPC_RCOMP0.053–50.400R
OPCE_RCOMP0.051–50.700R
OUT123_EN0.309––
P0V8SLPDDR_FB0.036–30.600R
P0V8SLPDDR_FB_R0.034–0.310R
P0V8SLPDDR_SW00.0480.82032.400R
P0V8SLPDDR_SW10.0480.82032.400R
P0V9_TBT_X_SVR_AGND0.000––
P0V9SLPDDR_FB_R0.054–53.700R
P0V9SLPDDR_SW00.0550.900–
P0V9SLPDDR_SW10.0550.900–
P0V9SSD_FB_N0.002–0.600R
P0V9SSD_FB_P0.774––
P0V9SSD_FB_R_N0.001–1.300R
P0V9SSD_FB_R_P0.370––
P0V9SSD_SW00.3780.900–
P1V1_SLPDDR_SOCFET_EN0.570––
P1V1SLPS2R_SW00.2701.100–
P1V1SLPS2R_SW10.2701.100–
P1V2_BOOT_RC0.633––
P1V2_DRVH0.711––
P1V2_DRVH_R0.712––
P1V2_DRVL0.461––
P1V2_DRVL_R0.462––
P1V2_LL_SNUBOL––
P1V2_PHASE0.2241.200–
P1V2_SNS0.228––
P1V2_SNS_R0.223––
P1V2_SW0.223––
P1V2_VBST0.632––
P1V2REG_AGND0.000––
P1V2REG_MODE0.551––
P1V2REG_TRIP0.752––
P1V2REG_VREF0.646––
P1V2REG_VREF_ROL––
P1V2S0SW_FET_EN0.528––
P1V2S0SW_RAMP0.703––
P1V8_DFR_R0.703––
P1V8G3S_DSCHG_EN0.543––
P1V8G3S_DSCHG_EN_L0.572––
P1V8G3S_DSCHG_PATH0.316––
P1V8G3S_EN0.572––
P1V8G3S_SS0.708––
P1V8SLPS2R_SW00.3501.800–
P1VPRIM_FB0.195––
P1VPRIM_FB_R0.195––
P1VPRIM_SW00.1951.000–
P1VPRIM_SW10.1951.000–
P2V5_SSD_DISCHARGEOL––
P3V3G3H_COMP20.478––
P3V3G3H_COMP2_ROL––
P3V3G3H_CS2_L_N0.4203.300–
P3V3G3H_CS2_L_P0.4203.300–
P3V3G3H_CSP21.287––
P3V3G3H_DRVH0.981––
P3V3G3H_DRVH_R0.979––
P3V3G3H_DRVL0.559––
P3V3G3H_DRVL_R0.559––
P3V3G3H_RF0.593––
P3V3G3H_SNUBROL––
P3V3G3H_SW0.419––
P3V3G3H_VBST0.636––
P3V3G3H_VBST_R0.633––
P3V3G3H_VFB20.592––
P3V3G3H_VFB2_R0.419––
P3V3G3H_VFB2_R20.427––
P3V3G3H_VFB2_RROL––
P3V3G3H_VSW0.4203.3000.200R
P3V3G3HRTC_FB1.415––
P3V3G3HRTC_FB_R0.380––
P3V3G3HRTC_PGOOD0.696––
P3V3G3HRTC_PHASE10.3723.300–
P3V3G3HRTC_PHASE20.3723.300–
P3V3G3HRTC_RA_R0.380––
P3V3G3HRTC_SS0.539––
P3V3G3S_EN0.572––
P3V3G3S_SS0.708––
P3V3MAIN_PGOOD0.583––
P3V3TBT_X_RAMP0.502––
P5V_S4SW_SNS_FET_RAMPOL––
P5VG3S_COMP10.750––
P5VG3S_COMP1_ROL––
P5VG3S_CS1_L_N0.4285.000–
P5VG3S_CS1_L_P0.4285.000–
P5VG3S_CSP11.263––
P5VG3S_DRVH0.993––
P5VG3S_DRVH_R0.985––
P5VG3S_DRVL0.559––
P5VG3S_DRVL_R0.558––
P5VG3S_EN0.575––
P5VG3S_EN_DLY0.522––
P5VG3S_EN_R0.574––
P5VG3S_PGOOD0.585––
P5VG3S_SNUBROL––
P5VG3S_SW0.425––
P5VG3S_VBST0.633––
P5VG3S_VBST_R0.634––
P5VG3S_VFB10.587––
P5VG3S_VFB1_R0.426––
P5VG3S_VFB1_R20.434––
P5VG3S_VFB1_RROL––
P5VG3S_VSW0.4285.0000.100R
P5VP3V3_SKIPSEL0.489––
P5VP3V3_VREF20.488––
P5VP3V3_VREG30.517––
P5VXX_EN0.592––
PANEL_P3V3_EN0.574––
PANEL_P3V3_EN_D0.755––
PANEL_P5V_EN0.573––
PANEL_P5V_EN_D1.038––
PBUS_DIVIDER0.707––
PBUS_DIVIDER_OUT0.666––
PBUS_DIVIDER_REF0.673––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.336––
PBUSVSENS_EN_L0.486––
PBUSVSENS_EN_L_DIVOL––
PCH_BATLOW_L0.817––
PCH_BT_AUDIO_SYNC0.678––
PCH_BT_ROM_BOOT_L0.550––
PCH_CLK24M_XTALIN0.836––
PCH_CLK24M_XTALOUT0.833––
PCH_CLK24M_XTALOUT_R0.831––
PCH_CLKIN_XTAL0.003–0.700R
PCH_DDPB_CTRLDATA0.794––
PCH_DDPC_CTRLDATA0.794––
PCH_DIFFCLK_BIASREF0.063–60.600R
PCH_GPP_A60.819––
PCH_GPP_A70.818––
PCH_HSIO_PWR_EN0.815––
PCH_INTRUDER_L0.844––
PCH_JTAGX0.052–51.800R
PCH_LAN_WAKE_L0.816––
PCH_OPIRCOMP0.052–50.600R
PCH_PCIE_CLK100M_WLAN_N0.535––
PCH_PCIE_CLK100M_WLAN_P0.336––
PCH_PCIE_RCOMP_N0.314––
PCH_PCIE_RCOMP_P0.315––
PCH_PCIE_WLAN_D2R_C_N0.396––
PCH_PCIE_WLAN_D2R_C_P0.395––
PCH_PCIE_WLAN_D2R_N0.346––
PCH_PCIE_WLAN_D2R_P0.346––
PCH_PCIE_WLAN_R2D_C_N0.331––
PCH_PCIE_WLAN_R2D_C_P0.334––
PCH_PCIE_WLAN_R2D_N0.517––
PCH_PCIE_WLAN_R2D_P0.520––
PCH_PWRBTN_L0.762––
PCH_RTC_RESET_L0.768––
PCH_SOC_SYNC0.474––
PCH_STRP_CNV_DISABLE0.540––
PCH_STRP_ESPI0.800––
PCH_STRP_GPD70.817––
PCH_STRP_JTAGODTDIS0.810––
PCH_STRP_NO_REBOOT0.799––
PCH_STRP_SPIROM_SAF0.803––
PCH_STRP_XTAL_24MHZ0.801––
PCH_SWD_SOC_CLK0.554––
PCH_SWD_SOC_IO0.543––
PCH_UART_DEBUG_D2R0.697––
PCH_UART_DEBUG_R_D2R0.705––
PCH_UART_DEBUG_R_R2D0.701––
PCH_UART_DEBUG_R2D0.702––
PCH_UART2_CTS_L0.819––
PCH_USB2_COMP0.116––
PCH_USB2_VBUSSENSE0.781––
PCH_WLAN_AUDIO_SYNC0.682––
PCH_WLAN_CLKREQ_L0.818––
PCH_WLAN_CLKREQ_R_L0.559––
PCH_WLAN_DEV_WAKE0.826––
PCH_WLAN_PERST_L0.534––
PCIE_CLK100M_SSD0_01_N0.128––
PCIE_CLK100M_SSD0_01_P0.128––
PCIE_CLK100M_TBT_X_N0.330––
PCIE_CLK100M_TBT_X_P0.336––
PCIE_PME_L0.564––
PCIE_SSD0_D2R_N<0>0.407––
PCIE_SSD0_D2R_P<0>0.404––
PCIE_WAKE_L0.813––
PD_UPC_X_5V_EN0.641––
PD_UPC_XA_GPIO40.677––
PD_UPC_XB_GPIO10.682––
PD_UPC_XB_GPIO40.689––
PD_UPC_XB_GPIO90.709––
PD_UPC_XB_GPIO100.714––
PDM_DMIC_CLK00.492––
PDM_DMIC_CLK0_R0.471––
PDM_DMIC_CLK10.490––
PDM_DMIC_CLK1_R0.471––
PDM_DMIC_DATA0_UNSEC0.551––
PDM_DMIC_DATA10.459––
PDM_DMIC_DATA1_RR0.475––
PDM_DMIC_DATA1_UNSEC0.548––
PLT_RST_3V3_L0.594––
PLT_RST_L0.559––
PM_MEMVTT_EN0.380––
PM_OPC_ZVM_L0.528––
PM_PCH_PWROK0.485––
PM_PCH_SYS_PWROK0.518––
PM_RSMRST_L0.502––
PM_SLP_S0_3V3_L0.787––
PM_SLP_S0_L0.471––
PM_SLP_S3_L0.585––
PM_SLP_S4_L0.819––
PM_SLP_S5_L0.817––
PM_SLP_SUS_L0.812––
PM_SLP_TIEOFF0.718––
PM_SYSRST_L0.814––
PM_SYSRST_R_L0.521––
PM_THRMTRIP_L0.260––
PMIC_DISCHARGE_EN_RCOL––
PMU_ACTIVE_READY0.473––
PMU_CLK32K_PCH0.805––
PMU_CLK32K_PCH_1V00.862––
PMU_CLK32K_PCH_R0.773––
PMU_CLK32K_SOC0.474––
PMU_CLK32K_SOC_R0.506––
PMU_CLK32K_WLANBT0.458––
PMU_CLK32K_WLANBT_R0.491––
PMU_COLD_RESET_L0.468––
PMU_CPU_ISENSE0.591––
PMU_CPU_VSENSE0.583––
PMU_CPUDDR_ISENSE0.591––
PMU_CPUEDRAM_ISENSE0.589––
PMU_CPUGT_ISENSE0.588––
PMU_CPUGT_VSENSE0.582––
PMU_CPUSA_ISENSE0.591––
PMU_CPUSA_VSENSE0.584––
PMU_CPUVCCIO_ISENSE0.589––
PMU_DDR1V2_ISENSE0.589––
PMU_DROOP_L0.480––
PMU_FORCE_DFU0.769––
PMU_INT_L0.472––
PMU_IREF0.759––
PMU_LCDPANEL_ISENSE0.592––
PMU_LDO3_OUT_R0.597––
PMU_OCARINA_ISENSE0.592––
PMU_ONOFF_L0.581––
PMU_ONOFF_R_L0.578––
PMU_ONOFF_R_L_CONN0.576––
PMU_OTHER3V3_HI_ISENSE0.591––
PMU_OTHER5V_HI_ISENSE0.592––
PMU_P5V_CPUREGMISC_ISENSE0.589––
PMU_PVDDMAIN_EN0.774––
PMU_RSLOC_RST_L0.514––
PMU_SSDNAND_ISENSE0.591––
PMU_SYS_ALIVE0.418––
PMU_VDD_MAX0.558––
PP_KBDLED_CATHODE10.674––
PP_KBDLED_CATHODE1_ROL––
PP_KBDLED_CATHODE20.671––
PP_KBDLED_CATHODE2_ROL––
PP_SSD0_S4E0_VPP0.569––
PP_SSD0_S4E1_VPP0.602––
PP_SSD0_S4E2_VPP0.602––
PP_SSD0_S4E3_VPP0.603––
PP_VDD_SE_VDDC0.343––
PP_VDD_SE_VDDNV0.367––
PP_VDD_SE_VDDPLL0.365––
PP_VDD_SE_VHV0.323––
PP_VDD_SE_VREF0.698––
PP0V6_S0_DDRVTT0.137––
PP0V6_S3_MEM_VREFCA_A0.378––
PP0V6_S3_MEM_VREFDQ_A0.380––
PP0V6_S3_MEM_VREFDQ_B0.378––
PP0V8_SLPS2R0.220––
PP0V9_SLPDDR0.0550.90053.800R
PP0V9_SLPDDR_SOC_PCIEREFBUF0.062–61.900R
PP0V9_SSD00.3780.900–
PP0V9_SSD0_S4E0_VDD_PLL0.368––
PP0V9_SSD0_S4E1_VDD_PLL0.366––
PP0V9_SSD0_S4E2_VDD_PLL0.380––
PP0V9_SSD0_S4E3_VDD_PLL0.380––
PP0V9_TBT_X_LC0.340––
PP0V9_TBT_X_LVR0.274––
PP0V9_TBT_X_PCIE0.299––
PP0V9_TBT_X_SVR0.2820.900–
PP0V82_SLPDDR0.0480.82032.400R
PP0V95_S0_CPUVCCIO_REG_R0.1240.950–
PP1V_PRIM0.1951.000–
PP1V_S0SW0.223––
PP1V_S30.229––
PP1V1_SLPDDR0.347––
PP1V1_SLPDDR_SOC_VDDIOPLLDDR_F0.347––
PP1V1_SLPDDR_SOC_XTAL_F0.347––
PP1V1_SLPS2R0.2701.100–
PP1V2_AWAKE0.532––
PP1V2_AWAKE_SOC_PCIEPLL_F0.530––
PP1V2_AWAKE_SOC_PCIEREFBUF_F0.533––
PP1V2_AWAKE_SOC_PLLCPU_F0.528––
PP1V2_AWAKE_SOC_PLLSOC_F0.528––
PP1V2_S0SW0.304––
PP1V2_S30.2241.200–
PP1V2_S3_CPUDDR0.219––
PP1V2_S3_REG_R0.2241.200–
PP1V05_PRIM_PCH_VCCA19P2_XW0.192––
PP1V05_PRIM_PCH_VCCABCLK_XW0.192––
PP1V05_PRIM_PCH_VCCAPLL_AUD_F0.192––
PP1V05_PRIM_PCH_VCCASRC_XW0.191––
PP1V05_PRIM_PCH_VCCAXTAL_F0.190––
PP1V05_PRIM_PCH_VCCDUSB_XW0.192––
PP1V05_PRIMSW_PCH_VCCAMPHYPLL_F0.191––
PP1V05_S5_PCH_VCCDSW0.514––
PP1V5_UPC_XA_LDO_CORE0.520––
PP1V5_UPC_XB_LDO_CORE0.515––
PP1V8_ACCEL_FILTOL––
PP1V8_AWAKE0.403––
PP1V8_AWAKE_SOC_FMON_RC0.453––
PP1V8_AWAKE_SOC_TSADC_RC0.403––
PP1V8_CODEC_VCP0.305––
PP1V8_CODEC_VL0.306––
PP1V8_DFR0.548––
PP1V8_DIS0.673––
PP1V8_DMIC0.309––
PP1V8_G3S0.308––
PP1V8_G3S_REG0.306––
PP1V8_G3S_WLANBT0.310––
PP1V8_IO_SSD00.363––
PP1V8_IO_SSD0_R0.761––
PP1V8_IO_SSD0_R2OL––
PP1V8_MESA0.528––
PP1V8_MESA_FILT_CONN0.528––
PP1V8_PRIM_PCH_VCCHDA_F0.314––
PP1V8_S0_THMSNSA_R0.316––
PP1V8_S0_THMSNSB_R0.314––
PP1V8_S30.466––
PP1V8_S3_MEM0.466––
PP1V8_S50.314––
PP1V8_SLPS2R0.3501.800–
PP1V8_SLPS2R_PMUVDDGPIO0.740––
PP1V8_SLPS2R_SOC_LPADC_RC0.435––
PP1V8_SLPS2R_SOC_LPOSC_RC0.449––
PP1V8_SSD0_S4E0_AVDD18_PLL0.359––
PP1V8_SSD0_S4E0_PCI_AVDD_H0.359––
PP1V8_SSD0_S4E1_AVDD18_PLL0.359––
PP1V8_SSD0_S4E1_PCI_AVDD_H0.359––
PP1V8_SSD0_S4E2_AVDD18_PLL0.363––
PP1V8_SSD0_S4E2_PCI_AVDD_H0.363––
PP1V8_SSD0_S4E3_AVDD18_PLL0.360––
PP1V8_SSD0_S4E3_PCI_AVDD_H0.363––
PP1V24_S5_PCH_VCCDPHY0.414––
PP1V25_SLPS2R_SMC_AVREF0.690––
PP2V5_ADC2_VREFOL––
PP2V5_NAND_SSD00.4162.500–
PP2V5_SSD0_AGND0.000––
PP3V_G3H_RTC0.457––
PP3V0_MESA0.561––
PP3V0_MESA_FILT_CONN0.560––
PP3V3_AWAKE0.646––
PP3V3_CODEC_VP0.368––
PP3V3_G3H0.4203.3000.200R
PP3V3_G3H_BMU0.414––
PP3V3_G3H_DFUMUXOL––
PP3V3_G3H_MESA_SW0.370––
PP3V3_G3H_PMU_VDDMAIN0.415––
PP3V3_G3H_PMU_VINRTC_R0.370––
PP3V3_G3H_RSLOC0.371––
PP3V3_G3H_RTC0.371––
PP3V3_G3H_RTC_DFR0.369––
PP3V3_G3H_RTC_MESA0.369––
PP3V3_G3H_RTC_REG_R0.3723.300–
PP3V3_G3H_SSD00.4203.300–
PP3V3_G3HSW_DFR0.570––
PP3V3_G3S0.379––
PP3V3_G3S_KBD0.380––
PP3V3_G3S_TPAD0.379––
PP3V3_G3S_WLANBT0.379––
PP3V3_S0_TBT_X_ISNS_R0.527––
PP3V3_S0SW_LCD0.494––
PP3V3_S0SW_LCD_R0.494––
PP3V3_S4SW_SNS0.541––
PP3V3_S50.379––
PP3V3_TBT_X_ANA0.533––
PP3V3_TBT_X_ANA_PCIE0.511––
PP3V3_TBT_X_ANA_USB20.492––
PP3V3_TBT_X_LC0.565––
PP3V3_TBT_X_S00.528––
PP3V3_TBT_X_SX0.496––
PP3V3_TBT_X_SX_R0.502––
PP3V3_UPC_XA_LDO0.506––
PP3V3_UPC_XB_LDO0.495––
PP5V_COREVR_VCC0.423––
PP5V_EADC2_AVDDOL––
PP5V_EDRAM_V5IN0.423––
PP5V_G3H_LDO0.491––
PP5V_G3S0.4285.0000.100R
PP5V_G3S_ALSCAM0.423––
PP5V_G3S_CPUREG_MISC0.420––
PP5V_G3S_DFR_FILT0.428––
PP5V_G3S_EDRAMPVCC0.426––
PP5V_G3S_EDRAMVCC0.426––
PP5V_G3S_FAN0.423––
PP5V_G3S_KBD0.4265.000–
PP5V_G3S_TPAD0.423––
PP5V_G3S_TPAD_CONN0.425––
PP5V_G3S_VCCIOPVCC0.425––
PP5V_G3S_VCCIOVCC0.425––
PP5V_MAIN_VCCSA0.424––
PP5V_MAIN_VCORE10.425––
PP5V_MAIN_VCORE20.423––
PP5V_MAIN_VGT10.425––
PP5V_MAIN_VGT20.425––
PP5V_S0_BKLT_A0.436––
PP5V_S0_BKLT_D0.433––
PP5V_S0SW_LCD0.572––
PP5V_S0SW_LCD_R0.572––
PP5V_S4SWOL––
PP5V_WLAN_ISNS_DOL––
PP16V0_MESA0.654––
PP16V0_MESA_FILT_CONN0.655––
PP17V0_MOJAVE_LDOIN0.594––
PP20V_USBC_XA_VBUS0.136––
PP20V_USBC_XB_VBUS0.141––
PPBUS_G3H0.33612.600–
PPBUS_G3H_SPKRAMP_LEFT0.33612.600–
PPBUS_G3H_SPKRAMP_RIGHT0.33812.600–
PPBUS_G3H_SSD00.33612.600–
PPBUS_HS_CPU0.33612.600–
PPDCIN_G3H0.56220.000–
PPDCIN_G3H_CHGR0.56220.000–
PPDCIN_XA_G3H_F0.56220.000–
PPDCIN_XB_G3H_F0.56220.000–
PPDCPRTC_PCH0.672––
PPVBAT_G3H_CHGR_R0.33612.650–
PPVBAT_G3H_CHGR_REG0.33612.600–
PPVBAT_G3H_CONN1.570––
PPVCC_CPU_PH10.0061.5005.200R
PPVCC_CPU_PH20.0061.5005.200R
PPVCC_S0_CPU0.0061.5005.200R
PPVCC_SW1_TPS621800.4162.500–
PPVCC_SW2_TPS621800.4162.500–
PPVCCEDRAM_S0_CPU0.0471.000–
PPVCCEDRAM_S0_REG_R0.0471.00047.500R
PPVCCGT_CPU_PH10.0061.5005.100R
PPVCCGT_CPU_PH20.0061.5005.100R
PPVCCGT_S0_CPU0.0061.5005.100R
PPVCCIO_S0_CPU0.1240.950–
PPVCCQ_ANI_SSD00.3631.800–
PPVCCSA_CPU_R0.0231.15023.000R
PPVCCSA_S0_CPU0.0231.15023.000R
PPVDD_SE_VDDA0.335––
PPVDDCPU_AWAKE0.0120.6259.800R
PPVDDCPUSRAM_AWAKE0.3881.060–
PPVIN_G3H_P3V3G3H0.33612.600–
PPVIN_G3H_P3V3G3HRTC0.337––
PPVIN_G3H_P3V3G3HRTC_R0.3373.300–
PPVIN_G3H_P5VG3S0.33812.600–
PPVIN_S0_CPUVR_VIN0.344––
PPVIN_S0SW_LCDBKLT0.899–0.573R
PPVIN_S0SW_LCDBKLT_F0.33612.600–
PPVIN_S0SW_LCDBKLT_R0.33612.600–
PPVIN_SW_LCDBKLT_SW0.899–0.573R
PPVOUT_BKLT_FB20.634––
PPVOUT_S0_KBDLED0.634––
PPVOUT_S0_KBDLED_R0.63540.000–
PPVOUT_S0_LCDBKLT1.250––
PPVOUT_S0_LCDBKLT_F1.25646.000–
PPVPCORE_S50.2991.000–
PPVTT_VTTREF0.492––
PROC_POPIRCOMP0.053–50.200R
PROG1_CPUCOREVR0.630––
PROG2_CPUCOREVR0.628––
PROG3_CPUCOREVR0.632––
PROG4_CPUCOREVR0.633––
PROG5_CPUCOREVR0.634––
PVCC_FB_N0.001–1.400R
PVCC_FB_P0.300––
PVCCCGT_PH1_AGND0.001–0.600R
PVCCCGT_PH2_AGND0.000–0.700R
PVCCCORE_PH1_AGND0.001–0.600R
PVCCCORE_PH2_AGND0.001–0.600R
PVCCCSA_AGND0.000––
PVCCEDRAM_BOOT_RC0.572––
PVCCEDRAM_DRVH0.584––
PVCCEDRAM_DRVH_R0.589––
PVCCEDRAM_DRVL0.474––
PVCCEDRAM_DRVL_R0.476––
PVCCEDRAM_LL0.045––
PVCCEDRAM_LL_SNUBOL––
PVCCEDRAM_PHASE0.0471.00047.500R
PVCCEDRAM_REFIN0.699––
PVCCEDRAM_VBST0.570––
PVCCEDRAMS0_AGND0.000––
PVCCEDRAMS0_CS_N0.0471.000–
PVCCEDRAMS0_CS_P0.0471.000–
PVCCEDRAMS0_EN0.586––
PVCCEDRAMS0_EN_FILT0.478––
PVCCEDRAMS0_EN_FILT_BUF0.524––
PVCCEDRAMS0_EN_R0.490––
PVCCEDRAMS0_FB0.554––
PVCCEDRAMS0_FSEL0.573––
PVCCEDRAMS0_OCSET0.562––
PVCCEDRAMS0_RTN0.556––
PVCCEDRAMS0_SREF0.567––
PVCCEDRAMS0_VO0.561––
PVCCEOPIO_EDRAM_PGOOD0.564––
PVCCIO_BOOT_RC0.587––
PVCCIO_DRVH0.578––
PVCCIO_DRVH_R0.578––
PVCCIO_DRVL0.472––
PVCCIO_DRVL_R0.472––
PVCCIO_EN0.579––
PVCCIO_LL0.124––
PVCCIO_LL_SNUBOL––
PVCCIO_PGOOD0.567––
PVCCIO_PHASE0.1240.950–
PVCCIO_VBST0.585––
PVCCIOS0_AGND0.001–0.900R
PVCCIOS0_CS_N0.1240.950–
PVCCIOS0_CS_P0.1240.950–
PVCCIOS0_EN0.588––
PVCCIOS0_EN_FILT0.482––
PVCCIOS0_EN_FILT_BUF0.522––
PVCCIOS0_EN_R0.501––
PVCCIOS0_FB0.554––
PVCCIOS0_FSEL0.569––
PVCCIOS0_RTN0.553––
PVCCIOS0_SREF0.566––
PVCCIOS0_VO0.560––
PVCCOIOS0_OCSET0.560––
PVCCPLLOC_EN0.506––
PVCCQ_LX00.3631.800–
PVCCQ_SSD_FB_DIS0.361––
PVCCQSSD_FB0.766––
PVCCQSSD_FB_R0.362––
PVCCQSSD_SW00.3631.800–
PVDD_LX00.3780.900–
PVDD_LX10.3780.900–
PVDD_SSD_FB_DIS0.372––
PVDD_SSD_FB_R0.371––
PVDDCPUAWAKE_FB_R0.011–10.900R
PVDDCPUAWAKE_SW00.0120.6259.800R
PVDDCPUAWAKE_SW10.0120.6259.800R
PVDDCPUAWAKE_SW20.0120.6259.800R
PVDDCPUAWAKE_SW30.0120.6259.800R
PVDDCPUSRAMAWAKE_SW00.3881.060–
PVDDQ_EN0.568––
PVDDQ_EN_R0.564––
PVDDQ_PGOOD0.577––
PVPCORES5_FB_N0.002–1.500R
PVPCORES5_FB_P0.300––
PVPCORES5_SW00.2991.000–
PVPCORES5_SW10.2991.000–
PVTT_VTTSNS0.137––
PWR_SCL_R00.470––
PWR_SDA_R00.467––
RSLOC_RST_L0.490––
S4E2_DROOP_L0.535––
S4E3_DROOP_L0.492––
SA_ISUMN_R1.026––
SAVE_BAT_G0.775––
SAVE_BAT_S1.569––
SD_RCOMP0.202––
SE_CTLR_FW_DWLD0.471––
SE_DEV_WAKE0.466––
SE_HOST_WAKE0.467––
SE_HOST_WAKE_R0.466––
SE_PWR_EN0.765––
SE_RX_N0.521––
SE_RX_P0.520––
SENSOR_PWR_EN0.634––
SEP_CAM_DISABLE_DFF_L0.497––
SEP_CAM_DISABLE_L0.468––
SEP_DISABLE_STROBE0.470––
SEP_DMIC_DISABLE_L0.470––
SEP_DMIC_DISABLE_OUT_L0.503––
SEP_WP0.749––
SMBUS_3V3_BATT_SCL0.935––
SMBUS_3V3_BATT_SDA0.937––
SMBUS_5_OEOL––
SMBUS_PCH_CLK0.803––
SMBUS_PCH_DATA0.802––
SMC_BMON_ISENSE0.811––
SMC_CALPE_ISENSE0.813––
SMC_CPU_HS_ISENSE0.808––
SMC_DCIN_ISENSE0.812––
SMC_DCIN_VSENSE0.806––
SMC_DEBUGPRT_R_RX0.470––
SMC_DEBUGPRT_R_TX0.469––
SMC_DEBUGPRT_RX0.470––
SMC_DEBUGPRT_TX0.470––
SMC_FAN_0_PWM0.476––
SMC_FAN_0_TACH0.474––
SMC_LID_LEFT0.460––
SMC_LID_RIGHT0.460––
SMC_PBUS_VSENSE0.807––
SMC_PCH_PWROK0.444––
SMC_PCH_SYS_PWROK0.447––
SMC_PECI_RX0.450––
SMC_PECI_TX0.463––
SMC_PECI_TX_R0.463––
SMC_PP1V8_WLANBT_ISENSE0.813––
SMC_PP3V3_WLANBT_ISENSE0.813––
SMC_PROCHOT_L0.463––
SMC_RSMRST_L0.449––
SMC_SYSRST_L0.447––
SMCRST_TIEOFF0.721––
SML_PCH_0_CLK0.796––
SML_PCH_0_DATA0.798––
SML_PCH_1_CLK0.507––
SML_PCH_1_DATA0.819––
SOC_CLKREQ_L0.816––
SOC_CLKREQ_R_L0.468––
SOC_COLD_RESET_L0.475––
SOC_DDR0_RREF0.530––
SOC_DDR0_ZQ0.407––
SOC_DDR1_RREF0.526––
SOC_DDR2_RREF0.522––
SOC_DDR3_ZQ0.587––
SOC_DEBUGPRT_RX0.476––
SOC_DEBUGPRT_TX0.476––
SOC_DFU_STATUS0.477––
SOC_DOCK_CONNECT0.473––
SOC_FORCE_DFU0.479––
SOC_HOLD_RESET0.475––
SOC_JTAG_SEL0.469––
SOC_KBD_BKLT_PWM0.465––
SOC_KBD_BKLT_PWM_R0.466––
SOC_MIPI0C_REXT0.815––
SOC_MIPI1C_REXT0.397––
SOC_MIPID_REXT0.774––
SOC_PCIE_DN_REXT0.785––
SOC_PCIE_STG0_REXT0.790––
SOC_PCIE_STG1_REXT0.792––
SOC_PCIE_UP_REXT0.786––
SOC_PERST_L0.463––
SOC_SOCHOT_L0.476––
SOC_SWD_MUX_SEL_PCH0.550––
SOC_TESTMODE0.467––
SOC_USB_REXT0.204––
SOC_USB_VBUS0.401––
SOC_WDOG0.472––
SOC_XTAL24M_IN0.820––
SOC_XTAL24M_OUT0.807––
SOC_XTAL24M_OUT_R0.807––
SPARE_UPC_XA_DBG0_R0.706––
SPARE_UPC_XA_DBG1_R0.699––
SPARE_UPC_XA_DBG2_R0.701––
SPARE_UPC_XA_DBG3_R0.701––
SPARE_UPC_XA_USB3_RN0.733––
SPARE_UPC_XA_USB3_RP0.727––
SPARE_UPC_XB_USB2_RN0.729––
SPARE_UPC_XB_USB2_RP0.702––
SPARE_UPC_XB_USB3_RN0.729––
SPARE_UPC_XB_USB3_RP0.728––
SPI_ACCEL_CS_L0.470––
SPI_AOP_SENSOR_MISO0.471––
SPI_AOP_SENSOR_MISO_R0.490––
SPI_DFR_CLK0.491––
SPI_DFR_CS_L0.470––
SPI_DFR_MISO0.471––
SPI_DFR_MISO_R0.491––
SPI_DFR_MOSI0.492––
SPI_IO2_STRAP_L0.766––
SPI_MESA_CLK0.495––
SPI_MESA_CLK_CONN0.494––
SPI_MESA_MISO0.472––
SPI_MESA_MISO_CONN0.474––
SPI_MESA_MOSI0.494––
SPI_MESA_MOSI_CONN0.493––
SPI_PCHROM_IO<2>0.799––
SPI_PCHROM_IO<3>0.804––
SPI_PCHROM_MOSI0.814––
SPI_SOCROM_CLK0.490––
SPI_SOCROM_CLK_R0.473––
SPI_SOCROM_CS_L0.474––
SPI_SOCROM_MISO0.427––
SPI_SOCROM_MISO_R0.420––
SPI_SOCROM_MOSI0.430––
SPI_SOCROM_MOSI_R0.435––
SPI_SOCROM_WP_L0.614––
SPI_TPAD_3V3_CLK0.560––
SPI_TPAD_3V3_CLK_R0.550––
SPI_TPAD_3V3_CS_L0.662––
SPI_TPAD_3V3_MISO0.667––
SPI_TPAD_3V3_MOSI0.684––
SPI_TPAD_3V3_MOSI_R0.664––
SPI_TPAD_CLK0.492––
SPI_TPAD_CLK_R0.475––
SPI_TPAD_CS_L0.468––
SPI_TPAD_MISOOL––
SPI_TPAD_MISO_R0.494––
SPIROM_USE_MLB0.815––
SPKR_ID00.477––
SPKR_ID10.479––
SPKRAMP_FL_AREG0.583––
SPKRAMP_FL_BSTN0.778––
SPKRAMP_FL_BSTP0.778––
SPKRAMP_FL_DREG0.536––
SPKRAMP_FL_MODE0.408––
SPKRAMP_FL_SNSN0.485––
SPKRAMP_FL_SNSP0.485––
SPKRAMP_FR_BSTN0.776––
SPKRAMP_FR_BSTP0.777––
SPKRAMP_FR_MODE0.470––
SPKRAMP_FR_SNSN0.492––
SPKRAMP_FR_SNSP0.493––
SPKRAMP_RESET_L0.368––
SPKRAMP_RL_AREG0.587––
SPKRAMP_RL_BSTN0.778––
SPKRAMP_RL_BSTP0.778––
SPKRAMP_RL_DREG0.532––
SPKRAMP_RL_MODE0.000––
SPKRAMP_RL_SNSN0.493––
SPKRAMP_RL_SNSP0.506––
SPKRAMP_RR_AREG0.583––
SPKRAMP_RR_BSTP0.778––
SPKRAMP_RR_DREG0.535––
SPKRAMP_RR_MODE0.463––
SPKRAMP_RR_SNSN0.480––
SPKRAMP_RR_SNSP0.486––
SPKRAMP_RW_AREG0.585––
SPKRAMP_RW_DREG0.536––
SPKRAMPL_IOUTOL––
SPKRAMPR_IOUTOL––
SPKRCONN_FL_OUTN0.487––
SPKRCONN_FL_OUTP0.492––
SPKRCONN_FR_OUTN0.492––
SPKRCONN_FR_OUTP0.490––
SPKRCONN_RL_OUTN0.497––
SPKRCONN_RL_OUTP0.499––
SPKRCONN_RR_OUTN0.482––
SPKRCONN_RR_OUTP0.483––
SPMI_CLK0.490––
SPMI_CLK_R0.470––
SPMI_DATA0.400––
SPMI_DATA_R0.414––
SSD_BFH0.430––
SSD_PMU_RESET_L0.474––
SSD0_CLK24M0.435––
SSD0_CLK24M_010.436––
SSD0_CLK24M_230.447––
SSD0_CLK24M_R0.436––
SSD0_CLKREQ0_L0.455––
SSD0_CLKREQ1_L0.455––
SSD0_CLKREQ2_L0.468––
SSD0_CLKREQ3_L0.456––
SSD0_LPB_L0.438––
SSD0_OCARINA_LPB_L0.439––
SSD0_OCARINA_PFN_L0.442––
SSD0_OCARINA_RESET_L0.435––
SSD0_OCARINA_WP_L0.735––
SSD0_PCIE_RESET_L0.430––
SSD0_PMIC_DISCHARGE_EN0.768––
SSD0_PMIC_RESET_L0.768––
SSD0_PMIC_VR_P2V5_EN0.773––
SSD0_RESET_L0.435––
SSD0_S4E_BOOT20.439––
SSD0_S4E_JTAG_SEL0.441––
SSD0_S4E_JTAG_TRST_L0.438––
SSD0_S4E_UART_RX0.440––
SSD0_S4E_UART_TX0.483––
SSD0_S4E0_ANI0_VREF0.770––
SSD0_S4E0_ANI1_VREF0.770––
SSD0_S4E0_DROOP_L0.489––
SSD0_S4E0_JTAG_TDI0.488––
SSD0_S4E0_JTAG_TDO0.459––
SSD0_S4E0_PCIE_RESREF0.783––
SSD0_S4E0_SWD_UID00.481––
SSD0_S4E0_SWD_UID10.479––
SSD0_S4E0_UART_TX0.481––
SSD0_S4E0_ZQ_C0.101––
SSD0_S4E0_ZQ_L0.301––
SSD0_S4E1_ANI0_VREF0.781––
SSD0_S4E1_ANI1_VREF0.781––
SSD0_S4E1_DROOP_L0.486––
SSD0_S4E1_JTAG_TDO0.471––
SSD0_S4E1_PCIE_RESREF0.783––
SSD0_S4E1_SWD_UID00.481––
SSD0_S4E1_SWD_UID10.481––
SSD0_S4E1_UART_TX0.481––
SSD0_S4E1_ZQ_C0.101––
SSD0_S4E1_ZQ_L0.301––
SSD0_S4E2_ANI0_VREF0.790––
SSD0_S4E2_ANI1_VREF0.790––
SSD0_S4E2_JATG_TDO0.477––
SSD0_S4E2_PCIE_RESREF0.794––
SSD0_S4E2_SWD_UID00.513––
SSD0_S4E2_SWD_UID10.518––
SSD0_S4E2_UART_TX0.519––
SSD0_S4E2_ZQ_C0.101––
SSD0_S4E2_ZQ_L0.305––
SSD0_S4E3_ANI0_VREF0.785––
SSD0_S4E3_ANI1_VREF0.782––
SSD0_S4E3_JTAG_TDO0.488––
SSD0_S4E3_PCIE_RESREF0.786––
SSD0_S4E3_SWD_UID00.483––
SSD0_S4E3_SWD_UID10.485––
SSD0_S4E3_UART_TX0.484––
SSD0_S4E3_ZQ_C0.101––
SSD0_S4E3_ZQ_L0.301––
SSD0_STG01_ADDR0.582––
SSD0_SWCLK0.431––
SSD0_SWCLK_ROL––
SSD0_SWDIO0.430––
SSD0_VR_P2V5_EN0.647––
SSD0_VR_P2V5_PGOOD0.575––
SSD0_WP_L0.732––
SSDNAND_IOUTOL––
SWD_SOC_DEBUG_SWCLK0.505––
SWD_SOC_DEBUG_SWDIO0.498––
SWD_SOC_SWCLK0.471––
SWD_SOC_SWCLK_XB0.505––
SWD_SOC_SWDIO0.471––
SWD_SOC_SWDIO_XB0.506––
SYS_DETECTOL––
SYS_DETECT_L0.482––
TBT_POC_RESET0.313––
TBT_PWR_EN0.569––
TBT_T_PLUG_EVENT_L0.812––
TBT_WAKE_3V3_L0.582––
TBT_WAKE_L0.472––
TBT_X_BATLOW_L0.591––
TBT_X_CIO_PWR_EN0.541––
TBT_X_CLKREQ_L0.807––
TBT_X_CLKREQ_R_L0.588––
TBT_X_HDMI_DDC_DATA0.589––
TBT_X_PCI_RESET_L0.551––
TBT_X_PCIE_BIAS0.791––
TBT_X_PLUG_EVENT_L0.585––
TBT_X_PWR_EN_1V80.570––
TBT_X_RBIAS0.776––
TBT_X_ROM_HOLD_L0.708––
TBT_X_ROM_WP_L0.584––
TBT_X_RSENSE0.473––
TBT_X_RTD3_PWR_EN0.594––
TBT_X_SPI_ARK_CLKOL––
TBT_X_SPI_CLK0.563––
TBT_X_SPI_CS_L0.592––
TBT_X_SPI_DBG_CLKOL––
TBT_X_SPI_DBG_CS_LOL––
TBT_X_SPI_DBG_MISOOL––
TBT_X_SPI_DBG_MOSIOL––
TBT_X_SPI_MISO0.592––
TBT_X_SPI_MOSI0.594––
TBT_X_TEST_EN0.100––
TBT_X_TEST_PWR_GOOD0.101––
TBT_X_USB_PWR_EN0.544––
TBT_XA_USB2_MXCTL0.589––
TBT_XA_USB2_RBIAS0.202––
TBT_XB_USB2_RBIAS0.203––
TBTTHMSNS_D1_N0.000––
TBTTHMSNS_D1_P0.649––
TBTXP3V3_IOUTOL––
TEST_CPU_A350.291––
TEST_CPU_BJ340.309––
TEST_CPU_BJ360.309––
TEST_CPU_CN360.340––
TEST_CPU_D340.294––
TEST_CPU_F340.346––
TEST_CPU_F370.350––
TEST_NOA_N_100.821––
TEST_NOA_N_110.822––
THMSNSA_ADDR_SEL0.651––
THMSNSA_D2_N0.000––
THMSNSA_D2_P0.651––
THMSNSA_D3_N0.000––
THMSNSA_D3_P0.649––
THMSNSA_D4_N0.000––
THMSNSA_D4_P0.651––
THMSNSA_DN0.000––
THMSNSB_ADDR_SEL0.650––
THMSNSB_D1_N0.000––
THMSNSB_D1_P0.653––
THMSNSB_D2_N0.000–1.200R
THMSNSB_D2_P0.648––
THMSNSB_D3_N0.002–1.700R
THMSNSB_D3_P0.648––
THMSNSB_D4_N0.000––
THMSNSB_D4_P0.649––
THMSNSB_DN0.000––
TP_CPU_PWRGD0.338––
TP_DFR_TOUCH_GPIO2OL––
TP_DFR_TOUCH_PANEL_DETECTOL––
TP_DFR_TOUCH_ROM_WCOL––
TP_FAN_RT_OTP1OL––
TP_FAN_RT_OTP2OL––
TP_JTAG_SOC_TRST_L0.472––
TP_LCD_IRQ_LOL––
TP_P3V3G3H_EN20.593––
TP_SMC_FIXTURE_MODE_L0.470––
TP_SPI_PCHROM_CLK0.817––
TP_SPI_PCHROM_CS_L0.803––
TP_USB_FIXT2_N0.475––
TP_USB_FIXT2_P0.468––
TP_USBC_PP20V_XA0.000––
TP_USBC_PP20V_XB0.000––
TP_WLAN_JTAG_SEL0.554––
TP_WLAN_JTAG_TCK0.570––
TP_WLAN_JTAG_TDI0.561––
TP_WLAN_JTAG_TDO0.563––
TP_WLAN_JTAG_TRST_L0.562––
TPAD_3V3_ACTUATOR_DISABLE_L0.919––
TPAD_3V3_SPI_EN0.590––
TPAD_3V3_SPI_INT_L0.928––
TPAD_ACTUATOR_DISABLE_L0.470––
TPAD_KBD_WAKE_L0.470––
TPAD_SPI_EN0.467––
TPAD_SPI_INT_L0.472––
TPADP3V3_IOUTOL––
TPADP5V_IOUTOL––
TPS62180_FB1.530––
TPS62180_FB_R0.426––
UART_BT_LH_D2R0.468––
UART_BT_LH_R2D0.469––
UART_SE_D2R0.465––
UART_SE_D2R_CTS_L0.464––
UART_SE_R2D0.452––
UART_SE_R2D_RTS_L0.450––
UART_WLAN_D2R0.467––
UART_WLAN_D2R_CTS_L0.467––
UART_WLAN_R2D0.467––
UART_WLAN_R2D_RTS_L0.467––
UPC_I2C_INT_L0.466––
UPC_PMU_RESET0.640––
UPC_X_SPI_CS_L0.583––
UPC_XA_FAULT_L0.662––
UPC_XA_FAULT_L_R0.677––
UPC_XA_R_OSC0.471––
UPC_XA_RESET0.004–1.000R
UPC_XA_SER_DBGOL––
UPC_XA_SS0.582––
UPC_XA_SWD_CLK0.597––
UPC_XA_SWD_DATA0.706––
UPC_XA_UART_RX0.552––
UPC_XA_UART_TX0.552––
UPC_XA_VDDIO_CFG0.341––
UPC_XB_FAULT_L0.670––
UPC_XB_FAULT_L_R0.674––
UPC_XB_R_OSC0.465––
UPC_XB_RESET0.003–0.500R
UPC_XB_SER_DBG0.679––
UPC_XB_SPI_CLK0.577––
UPC_XB_SPI_CS_L0.606––
UPC_XB_SPI_MISO0.606––
UPC_XB_SPI_MOSI0.608––
UPC_XB_SWD_DATA0.712––
UPC_XB_VDDIO_CFG0.580––
USB_EXTA_N0.471––
USB_EXTA_P0.468––
USB_SOC_DEBUG_NOL––
USB_SOC_DEBUG_POL––
USB_SOC_N0.714––
USB_SOC_P0.715––
USB_SOC_TYPEC_N0.717––
USB_SOC_TYPEC_P0.715––
USB2_UPC_PCH_XA_F_N0.474––
USB2_UPC_PCH_XA_F_P0.474––
USB2_UPC_PCH_XA_N0.474––
USB2_UPC_PCH_XA_P0.474––
USB2_UPC_PCH_XB_F_N0.475––
USB2_UPC_PCH_XB_F_P0.475––
USB2_UPC_PCH_XB_N0.475––
USB2_UPC_PCH_XB_P0.475––
USB3_BSSB_D2R_N0.349––
USB3_BSSB_D2R_P0.348––
USB3_BSSB_D2R_R_N0.349––
USB3_BSSB_D2R_R_P0.348––
USB3_BSSB_R2D_C_N0.334––
USB3_BSSB_R2D_C_P0.335––
USB3_BSSB_R2D_N0.705––
USB3_BSSB_R2D_P0.703––
USBC_X_RESET_L0.661––
USBC_XA_CC10.590––
USBC_XA_CC20.579––
USBC_XA_D2R_CR_N<1>0.000––
USBC_XA_D2R_CR_N<2>0.000––
USBC_XA_D2R_CR_P<1>0.000––
USBC_XA_D2R_CR_P<2>0.000––
USBC_XA_R2D_N<1>0.000––
USBC_XA_R2D_N<2>0.000––
USBC_XA_R2D_P<1>0.000––
USBC_XA_R2D_P<2>0.000––
USBC_XA_SBU10.661––
USBC_XA_SBU20.655––
USBC_XA_USB_BOT_N0.759––
USBC_XA_USB_BOT_P0.762––
USBC_XA_USB_TOP_N0.762––
USBC_XA_USB_TOP_P0.762––
USBC_XB_CC10.582––
USBC_XB_CC20.582––
USBC_XB_D2R_CR_N<1>0.000––
USBC_XB_D2R_CR_N<2>0.000––
USBC_XB_D2R_CR_P<1>0.000––
USBC_XB_D2R_CR_P<2>0.000––
USBC_XB_R2D_N<1>0.000––
USBC_XB_R2D_N<2>0.000––
USBC_XB_R2D_P<1>0.000––
USBC_XB_R2D_P<2>0.000––
USBC_XB_SBU10.655––
USBC_XB_SBU20.655––
USBC_XB_USB_BOT_N0.757––
USBC_XB_USB_BOT_P0.756––
USBC_XB_USB_TOP_N0.740––
USBC_XB_USB_TOP_P0.760––
UVP_DIS_L0.567––
VR0V9_IND_TBT_X0.282––
WC_L0.740––
WLAN_AUDIO_SYNC0.470––
WLAN_OP_ENOL––
WLAN_OP_EN_LOL––
WLAN_PWR_EN0.764––
WLAN_SROM_CLK0.632––
WLAN_SROM_CS0.704––
WLAN_SROM_CS_R0.607––
WLAN_SROM_DIN0.565––
WLAN_SROM_DOUT0.636––
WLAN_SROM_ORG0.705––
WLAN_THROTTLE0.463––
WLANBTP1V8_IOUTOL––
WLANBTP3V3_IOUTOL––
WLBT_HOST_WAKE0.464––
XDP_BPM_L<0>0.291––
XDP_CPU_PRDY_L0.255––
XDP_CPU_PREQ_L0.269––
XDP_CPU_PWRBTN_L0.773––
XDP_CPU_TCK0.052–51.800R
XDP_CPU_TDI0.239––
XDP_CPU_TDO0.229––
XDP_CPU_TMS0.239––
XDP_CPU_TRST_L0.284––
XDP_DBRESET_L0.810––
XDP_DP_INT_HPD0.530––
XDP_PCH_OBSDATA_A00.819––
XDP_PCH_OBSDATA_A10.820––
XDP_PCH_OBSDATA_A20.821––
XDP_PCH_OBSDATA_A30.819––
XDP_PCH_OBSDATA_B00.819––
XDP_PCH_OBSDATA_D10.821––
XDP_PCH_OBSDATA_D20.819––
XDP_PCH_OBSDATA_D30.818––
XDP_PCH_OBSFN_C10.819––
XDP_PCH_TCK0.312––
XDP_PCH_TDI0.240––
XDP_PCH_TDO0.230––
XDP_PCH_TMS0.240––
XDP_PCH_TRST_L0.285––
XDP_PM_RSMRST_L1.509––
XDP_PRESENT_CPU1.291––
XDP_PRESENT_L0.473––
XDP_USB_EXTC_OC_L0.806––
XDP_USB_EXTD_OC_L0.807––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-01987?

OpenBoardData's known-good values for PPBUS_G3H on the 820-01987: diode 0.336, voltage 12.600. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3H read on the 820-01987?

OpenBoardData's known-good values for PP3V3_G3H on the 820-01987: diode 0.420, voltage 3.300, resistance to ground 0.200R. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-01987?

OpenBoardData's known-good values for PP3V3_S5 on the 820-01987: diode 0.379. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-01987 board?

Open your own 820-01987 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License