Apple laptop board · OpenBoardData

820-4924 known-good readings

Known-good readings for the Apple laptop board 820-4924: 1,107 nets, including 100 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 99 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-4924.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 100 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 13

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.296––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on the 820-4924, based on its name (G3H = always on). The archive gives one known-good reading: diode mode to ground 0.296, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is available here. A diode reading far from 0.296 usually points to a short or a damaged component on the rail, but a small difference can be normal, so confirm with the voltage before replacing anything.

PP3V42_G3H_SMC_SPVSR0.32––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR — 820-4924 reference note

  • What it is: From its name, a 3.42 V always-on (G3H) rail feeding the SMC/SPVSR area. It's a startup-stage rail, so it should be present whenever the board has power.
  • Known-good reading: Diode mode to ground, 0.32 (community archive; no condition recorded). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the DC voltage on the net.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on the rail; a missing or low voltage with a normal diode reading points upstream at the rail's source. Confirm with a second measurement before replacing anything.
PPBUS_G3H0.130––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the "G3H" suffix in its name indicates it is always-on. The only known-good reading here is a diode value of 0.130 to ground, with no condition recorded; there is no known-good voltage reading for this rail.

  • Check with the board unpowered: diode mode, red probe on ground, black probe on PPBUS_G3H, and compare with 0.130.
  • Then apply power and measure the DC voltage on the rail.
  • A diode reading far from 0.130 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part.
PPBUS_G3H_R0.15––
AI: what PPBUS_G3H_R is and how to check it

PPBUS_G3H_R is the main battery-charging bus rail; the "G3H" in its name indicates it is always-on, present whenever the charger is connected. The archive lists one known-good reading: diode 0.15 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the charger connected. No known-good voltage reading is recorded here. A diode reading far below 0.15 suggests a short or leaky part on the rail; a much higher reading suggests an open path, but confirm with a second measurement before replacing anything.

PPDCIN_G3H0.650 DC%2bBoard%2bconnected1.965––
AI: what PPDCIN_G3H is and how to check it

PPDCIN_G3H is the always-on DC input rail (the G3H suffix is from the name), so it should be present whenever the charger or DC board is connected. Known-good readings in the archive: diode 0.650 with the DC board connected, and diode 1.965 in the other listed state; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage at the rail. A diode reading far from those values, or no voltage with the DC board connected, usually points to a problem on the input path or its supply rather than downstream rails; treat the readings as a guide, since they vary with board state.

PPDCIN_G3H_CHGR0.590––
AI: what PPDCIN_G3H_CHGR is and how to check it

PPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H suffix (from the name) marks it as an always-on startup rail, present whenever the charger is connected. The archive's only known-good figure is a diode reading of 0.590 to ground, with no condition recorded and no known-good voltage here. Check it unpowered in diode mode from the rail to ground, then with the charger connected measure the voltage on it. A diode reading far below 0.590 usually points to a short or leaky part on the rail; a much higher or open reading points to a broken path rather than a short. These are community readings and vary with board state, so treat them as a guide, and confirm against a matching rail or a known-good board before condemning anything.

PPDCIN_G3H_INRUSH0.590––
AI: what PPDCIN_G3H_INRUSH is and how to check it

PPDCIN_G3H_INRUSH is the inrush-limited DC input rail that feeds the G3H (always-on) section, judging from the name. The archive lists one known-good diode reading of 0.590 to ground; there's no known-good voltage reading here. Check it with the board unpowered in diode mode, red probe on the rail and black on ground, then confirm the voltage with the charger connected. A diode reading far from 0.590 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PPDCIN_G3H_ISOLOL––
AI: what PPDCIN_G3H_ISOL is and how to check it

PPDCIN_G3H_ISOL is the isolated DC-input rail that feeds the G3H (always-on) startup stage; the "ISOL" part of the name suggests it sits behind an isolation element from the main DC input. The only archived reading here is a diode value of OL to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from OL, or a voltage that doesn't come up, usually points to a short or an open in the input path rather than the rail itself — treat any single reading as a guide, not proof a part is bad.

PPVBAT_G3H_CHGR_R0.130––
AI: what PPVBAT_G3H_CHGR_R is and how to check it

PPVBAT_G3H_CHGR_R is the charger-side battery rail; the G3H in its name indicates it is always-on, and CHGR marks it as charger-related (both from the name). The archive lists one known-good diode reading of 0.130 to ground, with no condition recorded and no known-good voltage reading here. Check it unpowered in diode mode, red probe to ground, black to the rail, then confirm the voltage with power applied. A diode reading far from 0.130 usually points to a short or a leaky component on that rail, but one reading isn't proof a part is bad.

PPVBAT_G3H_CHGR_REG0.130––
AI: what PPVBAT_G3H_CHGR_REG is and how to check it

PPVBAT_G3H_CHGR_REG is a charger-side battery rail; from the name, G3H means it is always-on whenever the charger is connected. The only known-good reading here is diode mode 0.130 to ground, with no condition recorded and no known-good voltage or resistance value. Check it unpowered in diode mode to ground, then power the board from the charger and measure the voltage on the rail. A diode reading far from 0.130 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PPVBAT_G3H_CONNOL––
AI: what PPVBAT_G3H_CONN is and how to check it

PPVBAT_G3H_CONN is the battery connector side of the main battery rail; the G3H in the name indicates it is always-on, and that reading is from the name, not from a schematic. The only known-good entry here is a diode reading of OL to ground, so there is no known-good voltage or resistance value for this rail. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage at the connector. A diode reading far below OL to ground usually points to a short or a leaky path on that rail, but a single reading doesn't confirm a bad part.

PPVIN_G3H_P3V42G3H0.36––
AI: what PPVIN_G3H_P3V42G3H is and how to check it
  • What it is: From the name, PPVIN_G3H_P3V42G3H is the always-on (G3H) input feed for the P3V42G3H rail on the 820-4924. It should be present whenever the charger or battery supplies the board, before the main power rails come up.
  • Known-good reading: Diode mode to ground is 0.36, from the readings archive (community contribution, so treat it as a guide). No known-good voltage reading here.
  • How to check: Power off and unplug the charger, then measure diode mode from the net to ground and compare with 0.36. Then apply power and measure the voltage on the net.
  • What a far-off reading suggests: A much lower diode reading points to a short or leaky part on the net; a much higher one points to an open feed or a missing connection. Confirm with the voltage reading before replacing anything.
PPVRTC_G3H0.44––
AI: what PPVRTC_G3H is and how to check it
  • What it is: PPVRTC_G3H is the always-on rail for the RTC circuit, from the name: "G3H" means always on. It should be present whenever the board has standby power.
  • Known-good reading: diode 0.44 to ground (from the readings archive). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PPVRTC_G3H to ground; then apply power and measure the DC voltage on the rail.
  • What a far-off reading suggests: a diode value well below 0.44 usually points to a short or a leaky part on the rail; a value well above it can mean an open path. Confirm with the voltage measurement before replacing anything.

S5 and SUS: standby 14

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDC0.51––
AI: what PP1V2_S5_SMC_VDDC is and how to check it
  • What it is: From its name, PP1V2_S5_SMC_VDDC is a 1.2 V rail in the S5/SUS standby stage, feeding the SMC (system management controller) supply. The exact parts on it aren't known here.
  • Known-good reading: diode 0.51 (community archive, a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage, expecting about 1.2 V from the name.
  • If far off: a much lower diode reading suggests a short or a failing load on the rail; a correct diode reading with no voltage points upstream to the standby supply that should create it. Confirm with a second measurement before replacing anything.
PP1V05_SUS0.30––
AI: what PP1V05_SUS is and how to check it
  • PP1V05_SUS is a 1.05 V standby rail; the "SUS" part of the name indicates it is present in standby, before the board fully powers on.
  • Known-good reading from the archive: diode mode to ground 0.30 (board unpowered). No known-good voltage reading is recorded here.
  • To check it: power off, measure diode mode from the rail to ground and compare with 0.30; then power up and measure the DC voltage at the rail.
  • A diode reading far below 0.30 suggests a short or leaky load on the rail; far above it suggests an open path. A missing or wrong voltage with power applied points to the standby supply or its enable, not necessarily the rail itself.
PP3V3_S50.14––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply that should be present before the board fully powers on.

  • Known-good reading here: diode 0.14 to ground (community archive value, a guide only, no condition recorded).
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail.
  • Then power the board and measure the voltage on the rail; no known-good voltage reading is recorded here, so compare against a known-good board or the rail's expected 3.3 V.
  • A diode reading far from 0.14 usually points to a short or a leaky part on the rail; a correct diode reading with no voltage points upstream, at the standby supply that creates it.
PP3V3_S5_AVREF_SMC0.60––
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC — reference note

  • From its name, this is a 3.3 V standby (S5) rail that also carries an SMC analog reference (AVREF). The name suggests it should be present in standby, before the main rails come up.
  • Known-good reading in the archive: diode 0.60 in diode mode to ground, with no stated condition beyond that. No known-good voltage reading here.
  • To check it: power off and unplug, then diode mode from the rail to ground and compare with 0.60. Then power up in standby and measure the voltage; the name implies about 3.3 V, but that's general, not from this board's data.
  • A diode reading far below 0.60 usually points to a short or a leaky part on the rail; far above it suggests an open path. Confirm with a voltage measurement before replacing anything.
PP3V3_S5_SMC_VDDA0.32––
AI: what PP3V3_S5_SMC_VDDA is and how to check it

PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply; the S5 and SUS parts of the name indicate it comes up in the standby stage, before the board fully powers on (from the name). The archive lists one known-good reading: diode 0.32 in diode mode to ground, with no condition recorded. To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage; no known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.32 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part — verify with a second measurement before replacing anything.

PP3V3_S5RS3RS0_SYSCLKGEN0.14––
AI: what PP3V3_S5RS3RS0_SYSCLKGEN is and how to check it
  • What it is: From its name, a 3.3 V standby rail (S5/SUS) that also feeds the system clock generator (SYSCLKGEN). It should be present in standby, before the board fully powers on.
  • Known-good reading: diode 0.14 to ground, from the readings archive. That is the only known-good value recorded here; there is no known-good voltage or resistance for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.14. Then apply power and measure the voltage on the rail; it should sit near 3.3 V in standby.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a correct diode reading with no voltage points back toward the rail's source or its enable. Treat 0.14 as a guide only, since readings vary with board state, and confirm before replacing anything.
PP3V3_SUS3v34––
AI: what PP3V3_SUS is and how to check it

PP3V3_SUS is the 3.3 V standby rail, from its name: S5/SUS means it is present in standby before the main rails come up. The only known-good reading here is diode 3v34 in diode mode to ground with the board unpowered; no known-good voltage reading is recorded. Check it by measuring diode mode to ground with power off, then measure the voltage with power applied to confirm the rail comes up. A diode reading far from 3v34 usually points to a short or a faulty part on that rail, but a small difference can be normal, so compare with a matching net or a known-good board before replacing anything.

PP3V3_SUS_FET_R0.45––
AI: what PP3V3_SUS_FET_R is and how to check it

PP3V3_SUS_FET_R — reference note

  • From its name, this is a 3.3 V standby rail (SUS) that sits on the FET side of a switch or isolation point (FET_R), so it is present in standby, before the main rails come up.
  • Known-good from the readings archive: diode mode to ground 0.45. No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.45. Then power up and measure the voltage on the rail.
  • A diode reading far below 0.45 suggests a short or a leaky part on that rail; far above it suggests an open path. Confirm with the powered voltage before replacing anything.
PP5V_S50.45––
AI: what PP5V_S5 is and how to check it

PP5V_S5 — reference note

  • What it is: A 5 V rail in the S5 (standby) domain, from the name — it should be present in standby, before the board fully powers on.
  • Known-good reading: Diode mode to ground, board unpowered: 0.45. No known-good voltage reading here.
  • How to check: With power off, measure diode mode from PP5V_S5 to ground and compare with 0.45. Then apply power and measure the voltage on the rail.
  • If it's far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path. A missing or low voltage with a normal diode reading points upstream, to whatever feeds the rail. These are general guidelines, not confirmed causes.
PPBUS_S5_HS_COMPUTING0.13––
AI: what PPBUS_S5_HS_COMPUTING is and how to check it

PPBUS_S5_HS_COMPUTING is a standby-stage rail (S5/SUS, from the name), typically the main bus feeding the high-side computing section. The archive lists one known-good reading: diode 0.13, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure its voltage with power applied; no known-good voltage is recorded here. A diode reading far from 0.13 usually points to a short or leaky component on that rail, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PPBUS_S5_HS_OTHER3V30.13––
AI: what PPBUS_S5_HS_OTHER3V3 is and how to check it
  • What it is: From the name, PPBUS_S5_HS_OTHER3V3 is a PPBUS-derived 3.3 V high-side rail that comes up in the S5/SUS standby stage, before the main rails.
  • Known-good: The archive lists a diode reading of 0.13 to ground for this net. There is no known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with 0.13. Then apply power and measure the voltage on the net.
  • If it's far off: A diode reading well below 0.13 suggests a short or a leaky part on the rail; a much higher one can mean an open path. Treat 0.13 as a guide only, since readings vary with board state, and confirm before replacing anything.
PPBUS_S5_HS_OTHER5V0.13––
AI: what PPBUS_S5_HS_OTHER5V is and how to check it

PPBUS_S5_HS_OTHER5V (820-4924) — reference note

  • What it is: the name indicates a PPBUS-derived rail in the S5/SUS standby stage (from the name). "HS" usually means a high-side switch, so it is likely a switched branch of the main PPBUS supply, but that is general interpretation, not confirmed by board data.
  • Known-good reading: diode-to-ground 0.13 in the readings archive. No known-good voltage reading here.
  • How to check: power off and unplugged, measure diode mode from the rail to ground; then apply power and measure the DC voltage on the rail.
  • If it reads far from 0.13: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path or missing connection. Confirm with a voltage check before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP0.29––
AI: what PPVOUT_S5_PCH_DCPSUSBYP is and how to check it
  • What it is: From the name, PPVOUT_S5_PCH_DCPSUSBYP is a standby (S5/SUS) rail feeding the PCH's DC/DC bypass input. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.29 (community archive, guide only). No voltage or resistance reading is recorded here.
  • How to check: power off and unplug, then diode-mode from the rail to ground; then power up and measure the DC voltage on it.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a high or open reading points to a missing feed or broken trace. Confirm with the voltage before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP_R0.29––
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it
  • What it is: From the name, a standby (S5/SUS) rail — a PCH-side supply with a bypass/decoupling element. The exact parts on it aren't documented here.
  • Known-good: diode reading 0.29 to ground (community guide, condition not stated). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure its voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with a voltage check before replacing anything.

S4 15

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.41––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 power state, from its name — an "always-on-ish" stage rail that comes up during the S4 startup sequence. The only known-good reading here is a diode value of 0.41 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from PP3V3_S4 to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.41 usually points to a short or a leaky load on the rail, while a correct diode reading with no voltage points upstream to the S4 enable or the regulator feeding it. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP3V3_S4_FET_R0.45––
AI: what PP3V3_S4_FET_R is and how to check it

PP3V3_S4_FET_R is a 3.3 V rail at the S4 startup stage, judged from its name (S4 usually means a sleep/standby-state rail in Apple power sequencing — general, not from this board's data). The only known-good reading here is a diode value of 0.45 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. A reading far from 0.45 (near 0 or open) points to a short or a broken feed on that net.
  • Then power the board and measure the voltage on the rail; compare against a matching S4 rail or a known-good board, since no voltage value is recorded here.
  • A rail that's low or missing at S4 usually means the enable or upstream supply for that stage isn't coming up, but that's a likely cause, not a confirmed one.
PP3V3_S4_TBT0.41––
AI: what PP3V3_S4_TBT is and how to check it

PP3V3_S4_TBT is a 3.3 V rail in the S4 startup stage, judging from its name; the "TBT" suffix suggests it feeds Thunderbolt-related circuitry, though that part is general inference, not from board data. The only known-good reading here is diode mode to ground: 0.41, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far below 0.41 usually points to a short or a failing load on the rail; far above it can mean an open trace or missing part. No known-good voltage reading is available here, so compare against a known-good board of the same model.

PP3V3_S4_TBT_F0.42––
AI: what PP3V3_S4_TBT_F is and how to check it
  • What it is: PP3V3_S4_TBT_F is a 3.3 V rail, from its name, in the S4 startup stage and tied to the Thunderbolt section (TBT). The board data here is readings only, so which parts sit on it isn't known.
  • Known-good: diode reading 0.42 to ground, no condition given. No known-good voltage or resistance reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground; then power up and measure the DC voltage, expecting about 3.3 V from the name.
  • If far off: a much lower diode reading points to a short or leaky part on the rail; a correct diode reading with no voltage points upstream in the S4 enable or supply path. Compare against a matching S4 rail or a known-good board before condemning anything.
PP3V3_S4_TBTAPWR0.46––
AI: what PP3V3_S4_TBTAPWR is and how to check it
  • What it is: PP3V3_S4_TBTAPWR is a 3.3 V rail in the S4 power state, judging from its name — the "TBT" part suggests it feeds Thunderbolt-related circuitry, but that's inference from the name, not confirmed by board data.
  • Known-good reading: diode 0.46 to ground (community archive value, no condition recorded). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open feed. A missing voltage with a normal diode reading points upstream, to the S4 enable and supply.
PP3V3_S4_TBTBPWR0.46––
AI: what PP3V3_S4_TBTBPWR is and how to check it

PP3V3_S4_TBTBPWR is a 3.3 V rail, from its name: the S4 suffix puts it in the S4 startup stage, and "TBTBPWR" suggests it feeds Thunderbolt-related power. The archive lists one known-good reading for it: diode 0.46 in diode mode, with no condition recorded. No known-good voltage reading is listed here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.46 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S4SW_SNS0.57––
AI: what PP3V3_S4SW_SNS is and how to check it

PP3V3_S4SW_SNS (820-4924) — the name indicates a 3.3 V switched S4-state rail with a sense line; that reading is from the name, not from a schematic.

  • Known-good: diode 0.57 to ground, no condition recorded. No known-good voltage reading here.
  • Check unpowered in diode mode from the net to ground, then power the board and measure the voltage on the net.
  • A diode reading far below 0.57 suggests a short or a leaky part on the rail; far above it suggests an open path. Either way, confirm with a second measurement before suspecting a part.
PP3V3_S4SW_SNS_FET_R0.57––
AI: what PP3V3_S4SW_SNS_FET_R is and how to check it

PP3V3_S4SW_SNS_FET_R is a 3.3 V rail at the S4 stage, judging from its name. The archive lists a diode reading of 0.57 to ground; no voltage reading is recorded here.

  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Compare with 0.57 as a guide.
  • Then power the board and measure the voltage on the rail; there is no known-good voltage here, so compare against a matching rail or a known-good board.
  • A diode reading far from 0.57 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.
PP3V3RHV_S4_TBTAPWR0.56––
AI: what PP3V3RHV_S4_TBTAPWR is and how to check it

PP3V3RHV_S4_TBTAPWR — the name indicates a 3.3 V rail (PP3V3), "RHV" high-voltage variant, enabled at the S4 startup stage, feeding Thunderbolt adapter power (TBTAPWR). This is inferred from the name only; the parts on the net aren't documented here.

  • Known-good: diode-to-ground 0.56 (community reading, a guide only, no condition recorded). No known-good voltage reading here.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.56 suggests a short or leaky part on the rail; far above suggests an open trace or missing connection. Confirm with voltage before replacing anything.
PP3V3RHV_S4_TBTAPWR_F0.56––
AI: what PP3V3RHV_S4_TBTAPWR_F is and how to check it

PP3V3RHV_S4_TBTAPWR_F — from the name, a 3.3 V rail (PP3V3), high-voltage-tolerant variant (RHV), active in the S4 power state, feeding Thunderbolt/Thunderbolt adapter power (TBTAPWR). It's a supply rail, not a signal.

  • Known-good: diode 0.56 to ground (community reading, a guide only; board state affects it). No known-good voltage reading here.
  • Check: power off and unplugged, diode mode from the rail to ground; then power on and measure the DC voltage, expecting about 3.3 V.
  • A diode far below 0.56 suggests a short or leaky load on the rail; far above suggests an open path or missing part. Confirm with a second reading before condemning anything.
PP3V3RHV_S4_TBTBPWR0.56––
AI: what PP3V3RHV_S4_TBTBPWR is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) in the S4 startup stage, feeding Thunderbolt power (TBTBPWR). The "RHV" part isn't explained in the available data.
  • Known-good reading: diode 0.56 to ground, no condition recorded. No known-good voltage reading here.
  • How to check: Power off and unplug, then diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a much higher one to an open path. Confirm with voltage before replacing anything.
PP5V_S40.56––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging from its name. The only known-good reading here is a diode value of 0.56 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from PP5V_S4 to ground and compare with 0.56.
  • Then power the board and measure the voltage on PP5V_S4; no known-good voltage is recorded here, so compare with a known-good board or the matching rail on the other side of a pair.
  • A diode reading far below 0.56 usually points to a short or a leaky part on the rail; a reading far above it can mean an open connection. A single reading isn't proof a part is bad, so confirm with a second measurement before replacing anything.
PP5V_S4_TPAD_F0.56––
AI: what PP5V_S4_TPAD_F is and how to check it

PP5V_S4_TPAD_F is a 5 V rail feeding the trackpad, and the S4 in its name places it in the S4 startup stage (both from the name). The archive lists one known-good reading: diode 0.56, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage; the data has no known-good voltage here, so compare against a matching rail or a known-good board. A diode reading far from 0.56 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a bad part.

PPBUS_S4_X239OL––
AI: what PPBUS_S4_X239 is and how to check it

PPBUS_S4_X239 is a main power-bus rail in the S4 startup stage, judging from the name. The only known-good reading recorded is diode mode to ground: OL, meaning no conduction to ground on that net. Check it with the board unpowered in diode mode from the net to ground, then with power applied measure the DC voltage; no known-good voltage reading is recorded here. A diode reading well below OL suggests a short or low resistance to ground on that bus, but a single reading isn't proof of a bad part, so compare with a matching net or a known-good board before replacing anything.

PPVIN_S4_TPAD_FUSEOL––
AI: what PPVIN_S4_TPAD_FUSE is and how to check it
  • What it is: From its name, PPVIN_S4_TPAD_FUSE is a power-input rail feeding the trackpad section, in the S4 startup stage. "FUSE" suggests it sits after a fuse or fuse-like element, so it's a feed rail rather than a regulated output.
  • Known-good readings: The archive gives a diode reading of OL (open) to ground for this net. There is no known-good voltage or resistance value recorded here.
  • How to check it: With the board unpowered, measure diode mode from the net to ground and expect OL; then apply power and measure the DC voltage on the net. Compare against a matching rail on the other side of the trackpad pair, or a known-good board, since the archive has no voltage figure.
  • What a far-off reading suggests: A diode reading well below OL points to a short or low-impedance path on that rail, so trace what it feeds before replacing anything. A missing voltage with power applied points upstream, toward the fuse element or the source feeding it. These are likely causes, not confirmed ones.

S3: memory 17

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP0V6_S3_MEM_VREFCA_A0.35––
AI: what PP0V6_S3_MEM_VREFCA_A is and how to check it
  • What it is: From the name, PP0V6_S3_MEM_VREFCA_A is a 0.6 V memory reference rail that comes up in the S3 (memory) stage. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.35 to ground, from the readings archive. There's no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.35; then power up and measure the voltage, expecting roughly 0.6 V from the name.
  • If it's far off: a diode reading well below 0.35 suggests a short or a leaky part on the rail; an open or high reading suggests a broken trace or missing part. A voltage that's low or missing points to the rail not being enabled or its source failing. These are likely causes, not confirmed ones, so trace the rail before replacing anything.
PP0V6_S3_MEM_VREFDQ_A0.39––
AI: what PP0V6_S3_MEM_VREFDQ_A is and how to check it

PP0V6_S3_MEM_VREFDQ_A is a 0.6 V memory reference rail; the name points to a 0.6 V supply in the S3 (memory) startup stage, and the VREFDQ part suggests a DDR reference voltage.

  • Known-good reading: diode 0.39 to ground (community archive, condition not stated). No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.39 usually points to a short or a leaky part on the rail, but one reading isn't proof; compare with a matching rail or a known-good board before replacing anything.
PP0V6_S3_MEM_VREFDQ_B0.40––
AI: what PP0V6_S3_MEM_VREFDQ_B is and how to check it

PP0V6_S3_MEM_VREFDQ_B is a 0.6 V memory reference rail; the S3 in the name marks it as a memory-stage rail (from the name). The archive lists one known-good diode reading, 0.40, with no condition noted, and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode reading far from 0.40 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V2_S30.20––
AI: what PP1V2_S3 is and how to check it

PP1V2_S3 is a 1.2 V supply rail; the S3 suffix, from the name, places it in the memory stage of startup. The only known-good reading here is a diode value of 0.20 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading is available here, so compare against a known-good board or the matching rail. A diode reading far from 0.20 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V2_S3_CPUDDR0.13––
AI: what PP1V2_S3_CPUDDR is and how to check it

PP1V2_S3_CPUDDR is the 1.2 V CPU DDR supply that comes up at the S3 (memory) stage of startup, judging by the rail name. The archive lists a diode reading of 0.13 to ground, with no condition noted, and no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.13 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP1V8_S30.36––
AI: what PP1V8_S3 is and how to check it
  • What it is: PP1V8_S3 is a 1.8 V rail that, from its name, belongs to the S3 (memory) startup stage on the 820-4924.
  • Known-good reading: diode 0.36 in the readings archive (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V8_S3 to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail; a missing or wrong voltage points to the rail's supply or enable. Confirm with a second measurement before replacing anything.
PP1V8_S3_REG_R0.376––
AI: what PP1V8_S3_REG_R is and how to check it

PP1V8_S3_REG_R is a 1.8 V rail; the S3 in the name marks it as a memory-stage supply, and REG suggests it comes from a regulator. The archive lists one known-good diode reading of 0.376, with no condition noted, and no known-good voltage here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.376 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S30.51––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that comes up at the S3 (memory) stage of startup, judging by its name; it's a main always-needed supply after the early stages. The archive lists a known-good diode reading of 0.51 to ground on this rail, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.51 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S3_FET_R0.57––
AI: what PP3V3_S3_FET_R is and how to check it
  • What it is: PP3V3_S3_FET_R is a 3.3 V rail. The S3 in the name marks it as a memory-stage rail (from the name); the FET_R suffix suggests a switched feed, but that's general reading, not from board data.
  • Known-good: diode 0.57 to ground, from the readings archive. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PP3V3_S3RS0_CAMERA0.32––
AI: what PP3V3_S3RS0_CAMERA is and how to check it
  • What it is: PP3V3_S3RS0_CAMERA is a 3.3 V rail that, from its name, belongs to the S3 (memory) startup stage and feeds the camera section. The "RS0" suffix suggests a switched or gated version of the rail.
  • Known-good reading: diode 0.32 to ground. That is the only archived value for this rail; there is no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.32. Then apply power and measure the voltage at the rail.
  • If it's far off: a much lower diode reading points to a short or leaky part on the rail; a much higher one points to an open trace or missing part. A missing voltage with a normal diode reading points upstream, to the enable or supply for the switch. These are general guidelines, not confirmed causes for this board.
PP3V3_S3RS0_CAMERA_R0.32––
AI: what PP3V3_S3RS0_CAMERA_R is and how to check it

PP3V3_S3RS0_CAMERA_R — reference note

  • From its name, this is a 3.3 V rail that comes up at the S3 (memory) startup stage, feeding the camera circuit; the "RS0" and "R" suffixes are naming conventions, not values.
  • Known-good: diode-to-ground reading of 0.32 in the readings archive. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail, and compare to 0.32. Then power up and measure the voltage on the rail.
  • A diode reading far below 0.32 suggests a short or leaky load on the rail; far above suggests an open path. Confirm with a second measurement before replacing anything.
PP5V_S30.39––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is the 5 V rail that comes up at the S3 (memory) stage of startup, judging by its name; the archive has no part list for this board. Known-good: diode reading 0.39 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. No known-good voltage reading is recorded here, so compare against a matching 5 V rail or a known-good board. A diode reading far from 0.39 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S3_AUDIO_XW0.42––
AI: what PP5V_S3_AUDIO_XW is and how to check it

PP5V_S3_AUDIO_XW is a 5 V rail for audio that comes up at the S3 (memory) stage of power-on, judged from its name. The only known-good reading here is a diode value of 0.42; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.42 usually points to a short or a leaky part on that rail, while a correct diode reading with no voltage points upstream to the S3 enable or supply. These are community readings and a guide only, so compare against a matching rail or a known-good board before condemning anything.

PP5V_S3_LTUSB_A_ILIM0.52––
AI: what PP5V_S3_LTUSB_A_ILIM is and how to check it
  • What it is: From the name, PP5V_S3_LTUSB_A_ILIM is a 5 V rail that comes up at the S3 (memory) stage and serves the left USB-A port's current-limit circuit. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.52 to ground, from the readings archive. This is a community figure and a guide only; there is no known-good voltage or resistance value for this rail.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the DC voltage on the rail.
  • If it's far off: a diode reading well below 0.52 suggests a short or leaky part on that net; a much higher or open reading suggests a broken trace or missing connection. Confirm with a voltage check under power before replacing anything.
PP5V_S3RS0_ALSCAM_F0.42––
AI: what PP5V_S3RS0_ALSCAM_F is and how to check it

PP5V_S3RS0_ALSCAM_F — reference note

  • From its name, this is a 5 V rail (PP5V) that comes up in the S3 (memory/suspend-to-RAM) power state, and the ALSCAM_F suffix suggests it feeds the camera circuit. The name is the only source for that; the parts on the net aren't documented here.
  • Known-good reading in the archive: diode mode to ground 0.42. No known-good voltage or resistance reading is recorded for this rail.
  • To check it: power off and discharge, then measure diode mode from the rail to ground. With power applied, measure the voltage and confirm it appears only in S3, not in S0-only or off states.
  • A diode reading far below 0.42 usually points to a short or a failing load on the rail; far above it can mean an open trace or missing part. Treat 0.42 as a community guide, not a spec, and confirm against a matching rail or a known-good board before replacing anything.
PPDDR_S3_REG_R0.127––
AI: what PPDDR_S3_REG_R is and how to check it

PPDDR_S3_REG_R is a memory-rail enable/regulator signal in the S3 (memory) startup stage, judged from its name. The archive's only known-good reading is diode 0.127 to ground, with no condition recorded; no voltage or resistance value is listed. Check it unpowered in diode mode to ground, then measure its voltage with the board powered. A diode reading far from 0.127 usually points to a short or a damaged component on that net, but confirm with voltage and resistance before replacing anything.

PPVTTDDR_S30.53––
AI: what PPVTTDDR_S3 is and how to check it

PPVTTDDR_S3 is the memory termination rail, going by its name and its S3 (memory) startup stage. The only known-good reading here is a diode value of 0.53 to ground; no voltage or resistance reading is recorded for this rail. With the board unpowered, measure diode mode from PPVTTDDR_S3 to ground and compare with 0.53, then power up and check the rail voltage against the memory rail's expected level. A diode reading far from 0.53 usually points to a short or an open on that net rather than a confirmed bad part, so verify with a second measurement before replacing anything.

S0: running 41

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V6_S0_DDRVTT0.13––
AI: what PP0V6_S0_DDRVTT is and how to check it

PP0V6_S0_DDRVTT is the 0.6 V DDR termination rail; the name suggests 0.6 V and the S0 suffix marks it as a running-state rail (from the name, not from a schematic). The only known-good reading here is a diode value of 0.13 to ground, with no condition noted, so treat it as a guide. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, which should sit near 0.6 V. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.13 usually points to a short or leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V05_S00.19––
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail; the S0 suffix, from the name, means it belongs to the running (S0) state rather than standby. The only known-good reading here is a diode value of 0.19 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.19 usually points to a short or a leaky load on the rail, while a correct diode reading with no voltage points upstream to the regulator or its enable. These are guides only, and the archive doesn't say which parts sit on this net.

PP1V5_S00.31––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, so it should be present once the board is fully on. The archive lists a known-good diode reading of 0.31 to ground for this net, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the net; then power up and measure the voltage, expecting about 1.5 V. A diode reading far from 0.31 usually points to a short or a faulty part on that rail, but confirm with the voltage before replacing anything. No known-good voltage reading is recorded here, so compare against a known-good board if the voltage looks wrong.

PP1V5_S0_AUDIO_DIG0.36––
AI: what PP1V5_S0_AUDIO_DIG is and how to check it

PP1V5_S0_AUDIO_DIG is a 1.5 V digital audio rail; the "S0" in the name indicates it is up in the running state. The only known-good figure here is a diode reading of 0.36 to ground, with no condition noted, so treat it as a guide. Check it with the board unpowered in diode mode from the rail to ground, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far from 0.36 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP1V05_S0_PCH_VCC_ICC0.19––
AI: what PP1V05_S0_PCH_VCC_ICC is and how to check it

PP1V05_S0_PCH_VCC_ICC is a 1.05 V rail feeding the PCH; the S0 in the name indicates it belongs to the running (S0) power state, and the VCC_ICC suffix suggests a PCH core supply (from the name, not from board data).

  • Known-good: diode 0.19 in diode mode to ground, from the readings archive; treat it as a guide, since community readings vary with board state.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.19.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage reading is recorded here, so compare against a known-good board of the same model.
  • A diode reading far below 0.19 suggests a short or a failing load on the rail; far above it suggests an open path. Confirm with a second measurement before replacing anything.
PP1V05_S0_PCH_VCC_ICC_R0.19––
AI: what PP1V05_S0_PCH_VCC_ICC_R is and how to check it

PP1V05_S0_PCH_VCC_ICC_R is a 1.05 V rail, from its name, in the S0 (running) state, feeding the PCH VCC_ICC domain. The archive's only known-good reading is a diode value of 0.19 to ground; no voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.19 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP1V05_S0_PCH_VCCAPLL_OPI0.19––
AI: what PP1V05_S0_PCH_VCCAPLL_OPI is and how to check it

PP1V05_S0_PCH_VCCAPLL_OPI is a 1.05 V rail; from the name it supplies the PCH's VCCAPLL (analog PLL) section and is an S0 rail, so it should be present once the board is running. The only known-good reading here is a diode value of 0.19 to ground; there is no known-good voltage reading for this rail in the data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.19 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP1V05_S0_REG_R0.19––
AI: what PP1V05_S0_REG_R is and how to check it

PP1V05_S0_REG_R is a 1.05 V rail; the "S0" and "REG" parts of the name suggest it is a regulator output active in the running (S0) state, though that is from the name only. The archive lists one known-good reading: diode 0.19 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.19 usually points to a short or a failing load on the rail; a high or open reading points to a broken feed or an open component.

PP1V5_S0SW_AUDIO_HDA0.34––
AI: what PP1V5_S0SW_AUDIO_HDA is and how to check it

PP1V5_S0SW_AUDIO_HDA (820-4924) — reference note

  • From the name: a 1.5 V rail (PP1V5) for the audio/HDA section, switched (SW) and active in the S0 running state. That's from the name only, not from a schematic.
  • Known-good reading in the archive: diode mode to ground 0.34, with no condition recorded. No known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.34. Then power up and measure the DC voltage at the rail; expect about 1.5 V once the board is in S0.
  • A diode reading far below 0.34 suggests a short or a leaky load on the rail; far above suggests an open path. Either way, confirm with the powered voltage before suspecting a part, since one reading alone isn't proof.
PP1V05_S0SW_PCH_HSIO0.23––
AI: what PP1V05_S0SW_PCH_HSIO is and how to check it

PP1V05_S0SW_PCH_HSIO is a 1.05 V rail feeding the PCH high-speed I/O, from the name; the S0SW part suggests it is switched on in the running (S0) state. The archive's only known-good figure is a diode reading of 0.23 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and in S0. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.23 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V05_S0SW_PCH_VCCSATA3PLL0.24––
AI: what PP1V05_S0SW_PCH_VCCSATA3PLL is and how to check it
  • What it is: From the name, a 1.05 V rail (PP1V05) that is switched on in the S0 running state (S0SW) and feeds the PCH's SATA 3 PLL supply (PCH_VCCSATA3PLL). It is a small PCH-side rail, not a main power rail.
  • Known-good reading: Diode mode to ground, 0.24. No known-good voltage reading here, and no condition is recorded for the 0.24.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up, let the board reach S0, and measure the voltage at the rail.
  • If far from known-good: A diode reading well below 0.24 suggests a short or leaky load on the rail; well above it suggests an open path. Confirm with the voltage under power before condemning anything, since a single reading can mislead.
PP1V05_S0SW_PCH_VCCUSB3PLL0.23––
PP3V3_S00.32––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, as the name indicates. The archive lists a diode reading of 0.32 to ground for this rail; no voltage reading is recorded here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.32.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed here, so compare against a known-good board or the rail's expected 3.3 V.
  • A diode reading far from 0.32 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.
PP3V3_S0_AUDIO_ANALOG0.34––
AI: what PP3V3_S0_AUDIO_ANALOG is and how to check it
  • What it is: From the name, PP3V3_S0_AUDIO_ANALOG is a 3.3 V analog audio rail that is up in the S0 (running) state.
  • Known-good reading: diode 0.34 to ground, from the readings archive. This is a community guide, not a factory spec, and no known-good voltage reading is recorded here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.34 suggests a short or a leaky load on the rail; a missing or low voltage with a normal diode reading points to the supply or enable side rather than the load. Confirm with a second measurement before replacing anything.
PP3V3_S0_CPUTHMSNS_R0.37––
AI: what PP3V3_S0_CPUTHMSNS_R is and how to check it

PP3V3_S0_CPUTHMSNS_R — from the name, a 3.3 V rail that is present in the S0 (running) state, feeding the CPU thermal sensor circuit.

  • Known-good reading in the archive: diode mode to ground 0.37 (no condition recorded). No known-good voltage reading here.
  • To check: power off and unplug, then diode mode from the net to ground; then power up and measure the voltage on the net.
  • A diode reading far from 0.37 usually points to a short or a leaky part on that net, or an open feed; the voltage should sit near 3.3 V once the board is in S0.
  • These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.
PP3V3_S0_EDP_R0.566–79.10k Screen-side Unplugged
AI: what PP3V3_S0_EDP_R is and how to check it

PP3V3_S0_EDP_R is a 3.3 V rail for the embedded DisplayPort (eDP) circuit; the S0 in the name indicates it is active in the running state, and the _R suffix is from the name only.

  • Known-good readings from the archive: diode 0.566 to ground, and 79.10k resistance with the screen-side connector unplugged. These are community values and a guide, not a guarantee.
  • To check it, power the board off and measure diode mode from the rail to ground, then measure resistance with the screen side unplugged to match the 79.10k condition. Then apply power and measure the voltage on the rail.
  • No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A diode or resistance far below known-good usually points to a short or a leaky part on the rail; a voltage that is missing or low with power applied points to the supply or enable side. Confirm with a second measurement before replacing anything.
PP3V3_S0_EDP_SW0.68––
AI: what PP3V3_S0_EDP_SW is and how to check it

PP3V3_S0_EDP_SW is a 3.3 V rail switched to the embedded DisplayPort section; the S0 suffix means it belongs to the running state, from the name. The archive lists one known-good diode reading of 0.68 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then confirm the voltage with the board powered in S0. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.68 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0_FET0.35––
AI: what PP3V3_S0_FET is and how to check it
  • PP3V3_S0_FET is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "FET" suggests it is switched through a FET.
  • Known-good reading from the archive: diode mode to ground 0.35. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe to ground, black to the rail. Then apply power and measure the voltage.
  • A diode reading far from 0.35 usually points to a short or a faulty component on that rail, but one reading isn't proof — confirm with a voltage check before replacing anything.
PP3V3_S0_TBTTHMSNS_R0.37––
AI: what PP3V3_S0_TBTTHMSNS_R is and how to check it

PP3V3_S0_TBTTHMSNS_R is a 3.3 V rail, from its name: the "S0" part means it belongs to the running state, and "TBTTHMSNS" suggests a Thunderbolt thermal sensor feed. The archive lists one known-good reading, a diode value of 0.37 to ground; there is no known-good voltage here, so treat 0.37 as a guide only. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage on the same point. A diode reading far from 0.37 usually points to a short or a damaged component on that rail, but a single reading is not proof, so compare with a matching net or a known-good board before replacing anything.

PP3V3_S0SW_SSD0.52––
AI: what PP3V3_S0SW_SSD is and how to check it

PP3V3_S0SW_SSD is the switched 3.3 V rail feeding the SSD, from its name: a 3.3 V supply that switches on in the S0 (running) state.

  • Known-good: diode 0.52 in the readings archive. No known-good voltage reading here.
  • Check with the board unpowered: diode mode from the rail to ground, red probe on ground. Then power up and measure the voltage, comparing against the S0 state.
  • A diode reading far from 0.52 usually points to a short or a leaky part on the rail; confirm with a resistance check before replacing anything.
PP3V3_S0SW_SSD_FET0.52––
AI: what PP3V3_S0SW_SSD_FET is and how to check it

PP3V3_S0SW_SSD_FET is a 3.3 V rail switched through a FET to the SSD, judging from its name (S0 = running state, SW = switched). The archive lists one known-good diode reading of 0.52 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.52 usually points to a short or a failing part on the rail, while a missing voltage with a normal diode reading points upstream to the switch or its enable. These readings are community guides and vary with board state, so confirm against a matching rail or a known-good board before replacing anything.

PP3V3_S0SW_SSD_FLT0.52––
AI: what PP3V3_S0SW_SSD_FLT is and how to check it

PP3V3_S0SW_SSD_FLT is a switched 3.3 V rail, from its name: an S0 (running-state) supply, switched, feeding the SSD circuit, with FLT likely meaning a filtered or fault-related branch. The archive's only known-good reading is a diode value of 0.52 to ground; there is no known-good voltage or resistance reading here. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then power up and measure the voltage. A diode reading far from 0.52 usually points to a short or a leaky component on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S00.43––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is up in the S0 (running) state, judging by its name. The only known-good reading here is a diode value of 0.43 to ground; there is no known-good voltage or resistance reading for this rail.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.43.
  • Then power the board and measure the voltage on the rail; it should be about 5 V, though that figure is general and not from this board's data.
  • A diode reading far below 0.43 usually points to a short or a leaky part on the rail; a much higher one can mean an open path. Treat any single reading as a guide, not proof a part is bad.
PP5V_S0_AUDIO_AMP_L0.395––
AI: what PP5V_S0_AUDIO_AMP_L is and how to check it

PP5V_S0_AUDIO_AMP_L is the 5 V audio-amplifier rail that the name marks as S0, meaning it comes up in the running state. The archive gives one known-good diode reading to ground: 0.395 (board unpowered). No known-good voltage reading is recorded here.

  • Check it with the board off: diode mode, red probe on ground, black on the rail. A far lower reading suggests a short or a leaky part on the rail; a far higher one suggests an open trace or missing connection.
  • Then power up and measure the voltage on the rail; it should sit near 5 V when the board is in S0. A missing or sagging voltage points to the rail's supply or enable rather than the amp itself.
  • These readings are community guides and vary with board state, so confirm against a matching rail or a known-good board before replacing anything.
PP5V_S0_AUDIO_AMP_R0.41––
AI: what PP5V_S0_AUDIO_AMP_R is and how to check it

PP5V_S0_AUDIO_AMP_R is the audio amplifier supply rail on the 820-4924. From its name it is a 5 V rail enabled in the S0 (running) state, and the _R suffix usually marks a switched or gated version of it (general naming convention, not from this board's data).

  • Known-good reading in the archive: diode mode to ground 0.41 (no condition recorded).
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage in the S0 state.
  • No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.
  • A diode reading far below 0.41 usually suggests a shorted load on the rail; far above it suggests an open path. Confirm with the voltage before replacing anything.
PP5V_S0_BKLT_A0.46––
AI: what PP5V_S0_BKLT_A is and how to check it
  • PP5V_S0_BKLT_A is a 5 V rail for the display backlight, enabled in the S0 (running) state — that's from the name, not from board data.
  • Known-good: diode-to-ground reading of 0.46 (community archive, guide only). No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far from 0.46 usually points to a short or a leaky part on that rail; confirm with a resistance check before replacing anything.
PP5V_S0_BKLT_D0.51––
AI: what PP5V_S0_BKLT_D is and how to check it

PP5V_S0_BKLT_D is the backlight rail: the name indicates a 5 V supply (PP5V) that is present in the S0 running state and feeds the display backlight (BKLT). The only known-good reading here is a diode-mode value of 0.51 to ground; no known-good voltage reading is available for this rail.

  • Check it with the board unpowered: diode mode from the rail to ground, and compare with 0.51.
  • Then power the board and measure the voltage on the rail once the board is in S0.

A diode reading far from 0.51 usually points to a short or a leaky component on the rail, but one reading isn't proof a part is bad. If the diode value looks right but the voltage never comes up, the fault is more likely upstream in the backlight enable or power sequence than on the rail itself.

PP5V_S0_CPUVR_VDD0.42––
AI: what PP5V_S0_CPUVR_VDD is and how to check it

PP5V_S0_CPUVR_VDD is a 5 V rail that, from its name, feeds the CPU voltage-regulator supply and is expected up in the S0 (running) state. The only known-good figure here is a diode reading of 0.42 to ground; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.42 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP5V_S0_FET0.47––
AI: what PP5V_S0_FET is and how to check it

PP5V_S0_FET is a 5 V rail that, from its name, is switched through a FET and belongs to the S0 (running) state on the 820-4924. The only known-good reading here is a diode value of 0.47 to ground; no known-good voltage reading is recorded. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage in S0. A diode reading far below 0.47 suggests a short or leaky load on the rail; far above it suggests an open path. These are community readings and vary with board state, so treat them as a guide, not a confirmed fault.

PP5V_S0_KBDBKLT_SW0.49––
AI: what PP5V_S0_KBDBKLT_SW is and how to check it

PP5V_S0_KBDBKLT_SW is a 5 V rail that, from its name, switches the keyboard backlight and belongs to the S0 (running) state. The archive lists one known-good diode reading of 0.49 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the net to ground, then power up and measure the voltage at the net. A diode reading far from 0.49 usually points to a short or a leaky part on that switched rail, but one reading alone doesn't confirm a fault.

PPVCC_S0_CPU0.02––
AI: what PPVCC_S0_CPU is and how to check it

PPVCC_S0_CPU is the CPU core power rail, active in the S0 (running) state, as the name indicates. The only known-good reading here is a diode value of 0.02 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.02 usually points to a short or a failed component on the rail, but a single reading isn't proof — compare against a known-good board before replacing anything.

PPVCC_S0_CPU_PH10.01––
AI: what PPVCC_S0_CPU_PH1 is and how to check it

PPVCC_S0_CPU_PH1 is a CPU power rail; the S0 in its name means it's active in the running state, and PH1 suggests one phase of a multi-phase CPU supply. The archive lists a diode reading of 0.01 to ground, with no condition given, and no known-good voltage here. Check it unpowered in diode mode from the net to ground, then measure its voltage with the board powered. A diode reading far from 0.01 usually points to a short or a failed phase component, but confirm with more than one reading before replacing anything.

PPVCC_S0_CPU_PH20.01––
AI: what PPVCC_S0_CPU_PH2 is and how to check it

PPVCC_S0_CPU_PH2 is a CPU power rail phase — the "S0" in the name indicates it's active in the running state, and "PH2" suggests it's one phase of the CPU's multi-phase VCC supply (that reading is from the name, not the data).

  • Known-good: diode 0.01 to ground in the archive. No known-good voltage reading here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail.
  • A diode reading far above 0.01 usually points to an open or high-resistance path in that phase; a short to ground reads near zero.
  • This rail is low-voltage and high-current, so treat 0.01 as a guide only and compare against a known-good board or the matching phase.
PPVCOMP_S0_CPU0.13––
AI: what PPVCOMP_S0_CPU is and how to check it
  • What it is: PPVCOMP_S0_CPU is a CPU-related rail; the "S0" part of the name indicates it belongs to the running (S0) power state. The exact function isn't documented here, so treat that as from the name only.
  • Known-good reading: diode 0.13 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading is available here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.13; then power the board and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually suggests a short or leaky part on that rail, while a much higher one can mean an open connection. A single reading doesn't confirm a bad part, so compare with a matching net or a known-good board before replacing anything.
PPVIN_S0_CPUVR_VIN0.14––
AI: what PPVIN_S0_CPUVR_VIN is and how to check it
  • What it is: From its name, PPVIN_S0_CPUVR_VIN is the input supply to the CPU voltage regulator, live in the S0 (running) state. The data doesn't say which parts sit on it.
  • Known-good reading: diode 0.14 to ground, from the readings archive. This is a community guide, not a factory spec; no known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.14. Then power up and measure the voltage on the rail.
  • If far off: A much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT0.92––
AI: what PPVIN_S0SW_LCDBKLT is and how to check it

PPVIN_S0SW_LCDBKLT is the LCD backlight input rail; the S0SW part of the name indicates it is a switched supply present in the running (S0) state. The archive lists one known-good diode reading of 0.92 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on the rail with power applied and the display connected. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far from 0.92 usually points to a short or a leaky component on the rail, but a single reading is only a guide.

PPVIN_S0SW_LCDBKLT_F0.19––
AI: what PPVIN_S0SW_LCDBKLT_F is and how to check it
  • What it is: From the name, PPVIN_S0SW_LCDBKLT_F is the switched input supply to the LCD backlight circuit, active in the S0 (running) state. It's a rail, not a signal.
  • Known-good reading: Diode mode to ground is 0.19 (community archive, guide only). No known-good voltage reading here.
  • How to check: Power off and measure diode mode from the rail to ground, then power on and measure the voltage present.
  • If it's far off: A much lower diode reading usually points to a short or leaky component on the rail; a missing voltage with power on points upstream to the backlight enable/switch path. Confirm with a second measurement before replacing anything.
PPVIN_S0SW_LCDBKLT_R0.19––
AI: what PPVIN_S0SW_LCDBKLT_R is and how to check it

PPVIN_S0SW_LCDBKLT_R is the switched input feed to the LCD backlight circuit; the S0 in the name indicates it belongs to the running state, and the LCDBKLT part points to the backlight boost supply. The only known-good figure recorded here is a diode reading of 0.19 to ground, with no condition noted, and there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage present on it. A diode reading far from 0.19 usually points to a short or a leaky component on that feed, but a single reading is only a guide, so compare against a matching rail or a known-good board before condemning anything.

PPVOUT_S0_KBDBKLT0.63––
AI: what PPVOUT_S0_KBDBKLT is and how to check it

PPVOUT_S0_KBDBKLT is the keyboard backlight output rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "KBDBKLT" points to keyboard backlight.

  • Known-good reading: diode 0.63 to ground (from the readings archive; treat as a guide, since readings vary with board state).
  • No known-good voltage reading is recorded here.
  • Check it with the board unpowered in diode mode to ground, then measure the voltage with the board powered and the backlight active.
  • A diode reading far from 0.63 usually points to a short or a faulty component on that rail, but confirm with a voltage check before replacing anything.
PPVOUT_S0_LCDBKLT1.114––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the S0 in the name indicates it belongs to the running state. The readings archive lists a diode reading of 1.114 for this net, with no condition noted, and no known-good voltage reading here. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied and the display connected. A diode reading far from 1.114 usually points to a short or a faulty component on the rail, but a small difference can be normal, so confirm with the voltage measurement before replacing anything.

PPVOUT_S0_PCH_DCPRTC0.701.60–
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it

PPVOUT_S0_PCH_DCPRTC — reference note

  • From its name, this is a power output rail (PPVOUT) in the S0 running state, feeding the PCH's DCPRTC supply. The name is the only description available here; which parts sit on the net isn't known.
  • Known-good readings from the archive: diode mode to ground 0.70, voltage 1.60. These are community readings and a guide only; no condition is recorded and no other reading types are listed.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage on the rail.
  • A diode reading far below 0.70 usually points to a short or a leaky load on the rail; a voltage far from 1.60 with a normal diode reading points to the supply side. A small difference can be normal, so confirm before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
4V5_NR0.68––
4V5_REG_EN0.73––
4V5_REG_IN0.42––
5VS3_VFB1_RR0.45––
ADAPTER_SENSE0.595 DC+Board+connected0.605––
ALL_SYS_PWRGD0.43––
ALL_SYS_PWRGD_ROL––
AP_CLKREQ_L0.50––
AP_PCIE_WAKE_L0.52––
AP_RESET_L0.53––
AP_S0IX_WAKE_L0.49––
AP_S0IX_WAKE_SEL0.51––
AUD_CH_HS_GND0.02––
AUD_CONN_HP_LEFT1.75––
AUD_CONN_SLEEVE0.00––
AUD_CONN_SLEEVE_XW0.00––
AUD_CONN_TIPDET_11.80––
AUD_HP_PORT_L1.30––
AUD_HP_PORT_R1.34––
AUD_HP_PORT_REFCH0.02––
AUD_HP_PORT_REFUS0.02––
AUD_HS_MIC_N0.02––
AUD_HS_MIC_P0.02––
AUD_HSBIAS0.55––
AUD_HSBIAS_FILT0.78––
AUD_HSBIAS_IN0.52––
AUD_HSBIAS_REF0.49––
AUD_IPHS_SWITCH_EN0.61––
AUD_LO2_L_N0.70––
AUD_LO2_L_P0.70––
AUD_LO2_R_N0.70––
AUD_LO2_R_P0.70––
AUD_LO3_L_N0.69––
AUD_LO3_L_P0.69––
AUD_LO3_R_N0.69––
AUD_LO3_R_P0.69––
AUD_SPKRAMP_LIN_N0.70––
AUD_SPKRAMP_LIN_P0.70––
AUD_SPKRAMP_LSUBIN_N0.69––
AUD_SPKRAMP_LSUBIN_P0.69––
AUD_SPKRAMP_RIN_N0.68––
AUD_SPKRAMP_RIN_P0.68––
AUD_SPKRAMP_RSUBIN_N0.67––
AUD_SPKRAMP_RSUBIN_P0.67––
AUD_TIPDET_11.80––
AUD_TYPEDET0.79––
AUD_US_HS_GND0.02––
BKLT_EN_R0.62––
BKLT_ISET_KEYB0.72––
BKLT_KEYB10.71––
BKLT_KEYB20.71––
BKLT_PWM_KEYB0.60––
BKLT_SCL0.495––
BKLT_SD0.66––
BKLT_SDA0.495––
BKLT_SENSE_OUT0.77––
BMON_COMP_VREFOL––
BMON_IOUT0.00––
BMON_IOUT_DOL––
BMON_IOUT_ROL––
BT_PWRRST_L0.51––
CAM_DEBUG_RESET_L0.77––
CAM_GPIO30.77––
CAM_JTAG_SRST_L0.77––
CAM_PCIE_RESET_L0.47––
CAM_PCIE_WAKE_L0.52––
CAM_PWR_SEL0.82––
CAM_RAMCFG00.77––
CAM_RAMCFG10.77––
CAM_RAMCFG20.77––
CAM_SENSOR_WAKE_L0.81––
CAM_SENSOR_WAKE_L_CONN0.00––
CAM_TEST_MODE0.77––
CAM_TEST_OUT0.82––
CAM_UARTCTS0.77––
CAM_UARTRXD0.77––
CAM_XTAL_FREQ0.76––
CAM_XTAL_SEL0.77––
CAMERA_CLKREQ_L0.48––
CAMERA_PWR_EN0.64––
CAMERA_PWR_EN_PCH0.52––
CAMERA_PWR_EN_R0.61––
CAMERA_PWR_EN_RC0.75––
CHGR_ACIN0.500––
CHGR_AGATE0.610––
CHGR_AGATE_DIVOL––
CHGR_AMON0.700––
CHGR_BGATE0.645––
CHGR_BMON0.72––
CHGR_BOOT0.560––
CHGR_CELL0.650––
CHGR_CSI_N0.595––
CHGR_CSI_P0.590––
CHGR_CSI_R_N0.62––
CHGR_CSI_R_P0.62––
CHGR_CSO_N0.13––
CHGR_CSO_P0.13––
CHGR_CSO_R_N0.130––
CHGR_CSO_R_P0.130––
CHGR_DCIN0.60––
CHGR_DCIN_D_R0.570––
CHGR_ICOMP0.710––
CHGR_ICOMP_RC1.72––
CHGR_LGATE0.46––
CHGR_PHASE0.13––
CHGR_RST_L0.470––
CHGR_SGATE0.615––
CHGR_SGATE_DIVOL––
CHGR_UGATE0.58––
CHGR_VCOMP0.710––
CHGR_VCOMP_ROL––
CHGR_VFRQ0.460––
CHGR_VNEG0.500––
CHGR_VNEG_ROL––
CLK25M_CAM_CLKN0.81––
CLK25M_CAM_CLKP0.45––
CLK25M_CAM_XTALNOL––
CLK25M_CAM_XTALPOL––
CLK25M_CAM_XTALP_ROL––
CODEC_FLYN0.80––
CODEC_FLYP0.46––
CODEC_HS_MIC_N0.78––
CODEC_HS_MIC_P0.78––
CODEC_MICIN20.73––
CODEC_VCOM0.72––
CODEC_VREF_ADC0.79––
CPU_CATERR_L0.30––
CPU_CFG_RCOMP0.12––
CPU_CFG<0>0.35––
CPU_CFG<1>0.37––
CPU_CFG<2>0.31––
CPU_CFG<3>0.30––
CPU_CFG<4>0.34––
CPU_CFG<5>0.31––
CPU_CFG<6>0.31––
CPU_CFG<7>0.31––
CPU_CFG<8>0.37––
CPU_CFG<9>0.35––
CPU_CFG<10>0.31––
CPU_CFG<11>0.31––
CPU_CFG<12>0.31––
CPU_CFG<13>0.30––
CPU_CFG<14>0.31––
CPU_CFG<15>0.31––
CPU_CFG<16>0.30––
CPU_CFG<17>0.30––
CPU_CFG<18>0.31––
CPU_CFG<19>0.31––
CPU_MEMVTT_PWR_EN_LSVDDQ0.35––
CPU_OPI_RCOMP0.05––
CPU_PECI0.36––
CPU_PECI_R0.32––
CPU_PROCHOT_L0.20––
CPU_PROCHOT_R_L0.27––
CPU_PWRGD0.38––
CPU_RTN0.00––
CPU_SM_RCOMP<0>0.18––
CPU_SM_RCOMP<1>0.12––
CPU_SM_RCOMP<2>0.10––
CPU_THRMTRIP_3V30.74––
CPU_VCCSENSE_N0.00––
CPU_VCCSENSE_P0.00––
CPU_VCCSENSE_P_R0.00––
CPU_VCCSENSE_P_RC1.59––
CPU_VCCST_PWRGD0.68––
CPU_VIDALERT_L0.22––
CPU_VIDALERT_R_L0.35––
CPU_VIDSCLK0.19––
CPU_VIDSCLK_R0.29––
CPU_VIDSOUT0.20––
CPU_VIDSOUT_R0.29––
CPU_VR_EN0.29––
CPU_VR_READY0.57––
CPUHI_IOUT0.77––
CPUTHMSNS_ADDR_SEL0.00––
CPUTHMSNS_ALERT_L0.74––
CPUTHMSNS_D1_N0.75––
CPUTHMSNS_D1_P0.74––
CPUTHMSNS_D2_N0.74––
CPUTHMSNS_D2_P0.74––
CPUTHMSNS_DUR_SEL0.77––
CPUTHMSNS_TH_SEL0.76––
CPUTHMSNS_THM_L0.76––
CPUVR_BOOT10.61––
CPUVR_BOOT20.61––
CPUVR_COMP0.60––
CPUVR_COMP_RCOL––
CPUVR_DRSEL0.00––
CPUVR_FB0.59––
CPUVR_FB_RCOL––
CPUVR_FB20.62––
CPUVR_FCCM0.60––
CPUVR_IMON0.61––
CPUVR_ISEN10.62––
CPUVR_ISEN20.62––
CPUVR_ISNS_NOL––
CPUVR_ISNS_POL––
CPUVR_ISNS_R_POL––
CPUVR_ISNS1_N0.00––
CPUVR_ISNS1_P0.01––
CPUVR_ISNS2_N0.00––
CPUVR_ISNS2_P0.00––
CPUVR_ISUMN0.00––
CPUVR_ISUMN_R0.33––
CPUVR_ISUMN_RC0.86––
CPUVR_ISUMP0.48––
CPUVR_LGATE10.44––
CPUVR_LGATE20.43––
CPUVR_NTC0.62––
CPUVR_NTC_ROL––
CPUVR_PGOOD_R0.70––
CPUVR_PH1_SNUBOL––
CPUVR_PH2_SNUBOL––
CPUVR_PHASE10.00––
CPUVR_PHASE20.02––
CPUVR_PROG10.62––
CPUVR_PROG20.61––
CPUVR_PROG30.62––
CPUVR_PWM10.61––
CPUVR_PWM20.61––
CPUVR_SLOPE0.62––
CPUVR_UGATE10.63––
CPUVR_UGATE20.64––
CPUVSENSE_IN0.01––
CS4208_HDA_SDOUT0_R0.43––
CS4208_SPDIF_IN0.00––
CS4208_SPDIF_OUT0.71––
DCIN_ISOL_BLEEDER_NGATEOL––
DCIN_ISOL_BLEEDER_PSRCOL––
DCIN_ISOL_BLEEDER_ROL––
DCIN_ISOL_GATE0.78––
DCIN_ISOL_GATE_ROL––
DCIN_S5_VSENSEOL––
DCINVSENS_EN_L0.47––
DDRREG_1V8_VREF0.67––
DDRREG_DRVH0.63––
DDRREG_DRVL0.47––
DDRREG_EN0.57––
DDRREG_FB0.73––
DDRREG_LL0.127––
DDRREG_MODE0.56––
DDRREG_PGOOD0.51––
DDRREG_TRIP0.78––
DDRREG_VBST0.65––
DDRREG_VBST_RC0.65––
DDRREG_VDDQSNS0.18––
DDRREG_VDDQSNS_R0.17––
DDRREG_VTTSNS0.12––
DFET_CPO10.61––
DFET_CPO20.61––
DFET_OPENCH0.49––
DFET_OPENUS0.48––
DISP_MUX_EN0.52––
DISP_MUX_PRIORITYOL––
DISP_MUX_SEL_L0.50––
DMIC_CLK30.81––
DMIC_CLK3_R0.73––
DMIC_SDA20.00––
DMIC_SDA30.77––
DP_HDMI_TBT_DDC_CLK0.52––
DP_HDMI_TBT_DDC_DATA0.51––
DP_INT_AUX_NOL–1.00M Screen-side Unplugged
DP_INT_AUX_POL–1.00M Screen-side Unplugged
DP_INT_HPD0.79––
DP_INT_ML_N<0>OL––
DP_INT_ML_N<1>OL––
DP_INT_ML_N<2>OL––
DP_INT_ML_N<3>OL––
DP_INT_ML_P<0>OL––
DP_INT_ML_P<1>OL––
DP_INT_ML_P<2>OL––
DP_INT_ML_P<3>OL––
DP_TBTPA_DDC_CLK0.56––
DP_TBTPA_DDC_DATA0.57––
DP_TBTPA_HPD0.79––
DP_TBTPB_DDC_CLK0.56––
DP_TBTPB_DDC_DATA0.56––
DP_TBTSNK0_DDC_CLK0.57––
DP_TBTSNK0_HPD0.56––
DP_TBTSNK1_DDC_CLK0.60––
DP_TBTSNK1_DDC_DATA0.61––
DP_TBTSNK1_HPD0.50––
DP_TBTSRC_HPD0.56––
DPMUX_AUX_DDC_SEL0.89––
DPMUX_HPD_OUT0.63––
EDP_BKLT_PSR_EN0.55––
EDP_BKLT_PWM0.614–99.00k Screen-side Unplugged
EDP_PANEL_PWR0.65––
EDP_PANEL_PWR_OR_PSR_EN0.66––
EDP_PANEL_PWR_OR_PSR_EN_D10.92––
EDP_PANEL_PWR_OR_PSR_EN_D2OL––
EDP_TCON_PWR_EN_RC0.72––
ENET_MEDIA_SENSE0.50––
ENETSD_CLKREQ_L0.51––
FAN_RT_PWM0.89––
FAN_RT_TACHOL––
GND_BKLT_SGND0.02––
GND_CAM_PVSSD0.00––
GND_DDRREG_SGND0.06––
GPIO0_SPKR_SHUTDOWN0.54––
HDA_BIT_CLK0.47––
HDA_BIT_CLK_R0.41––
HDA_RST_L0.45––
HDA_RST_R_L0.41––
HDA_SDIN00.41––
HDA_SDOUT0.48––
HDA_SDOUT_R0.42––
HDA_SYNC0.47––
HDA_SYNC_R0.42––
HDD_PWR_EN0.66––
HDMI_HPD0.44––
HDMI_IG_CLK_C_N0.62––
HDMI_IG_CLK_C_P0.62––
HDMI_IG_DATA_C_N<0>0.70––
HDMI_IG_DATA_C_N<1>0.70––
HDMI_IG_DATA_C_N<2>0.70––
HDMI_IG_DATA_C_P<0>0.64––
HDMI_IG_DATA_C_P<1>0.64––
HDMI_IG_DATA_C_P<2>0.63––
HDMI_IG_DDC_CLK0.69––
HDMI_IG_DDC_DATA0.69––
HDMI_TBT_MUX_SEL_GPIO120.50––
HDMITBTMUX_FLAG_L0.43––
HDMITBTMUX_LATCH0.45––
HDMITBTMUX_SEL_TBT0.47––
HS_MIC_N2.06––
HS_MIC_P2.01––
HS_OTHER3V3_IOUTOL––
HS_OTHER5V_IOUTOL––
I2C_BKLT_SCL0.496–9.97M Screen-side Unplugged
I2C_BKLT_SDA0.495–9.89M Screen-side Unplugged
I2C_CAM_SCK0.76––
I2C_CAM_SDA0.76––
I2C_CAM_SMBDBG_CLK0.78––
I2C_CAM_SMBDBG_DAT0.78––
I2C_IOXP_SCL0.69––
I2C_IOXP_SDA0.66––
IOXP1_INT_L0.69––
IOXP1_RESET_L0.78––
IOXP2_INT_L0.63––
IOXP2_RESET_L0.75––
ISNS_1V05_S0_NOL––
ISNS_1V05_S0_POL––
ISNS_1V8_S3_POL––
ISNS_CAMERA_IOUTOL––
ISNS_CPUDDR_N0.00––
ISNS_CPUHIGAIN_N0.65––
ISNS_CPUHIGAIN_OUT0.73––
ISNS_CPUHIGAIN_OUT_R0.76––
ISNS_CPUHIGAIN_P0.37––
ISNS_CPUHIGAIN_R_N0.72––
ISNS_CPUHIGAIN_R_P0.39––
ISNS_DDR_IOUTOL––
ISNS_HS_COMPUTING_N0.18––
ISNS_HS_COMPUTING_P0.17––
ISNS_HS_OTHER3V3_NOL––
ISNS_HS_OTHER3V3_POL––
ISNS_HS_OTHER5V_NOL––
ISNS_HS_OTHER5V_POL––
ISNS_LCDBKLT_IOUTOL––
ISNS_LCDBKLT_N0.19––
ISNS_LCDBKLT_P0.19––
ISNS_LCDPANEL_IOUTOL––
ISNS_PP3V3S0_IOUTOL––
ISNS_PP3V3S0_NOL––
ISNS_PP3V3S0_POL––
ISNS_PP5VS0_IOUTOL––
ISNS_PP5VS0_NOL––
ISNS_PP5VS0_POL––
ISNS_S0_SSD_IOUT0.71––
ISNS_SSD_N0.52––
ISNS_SSD_P0.52––
ISNS_TBT_IVIN0.41––
ISNS_TBT_IVOUTOL––
ISNS_TBT_NOL––
ISNS_TBT_POL––
ISNS_X239_PEAK_FBKOL––
JTAG_ISP_TCK0.47––
JTAG_ISP_TDI0.48––
JTAG_ISP_TDO0.50––
JTAG_TBT_TDO0.51––
JTAG_TBT_TMS0.61––
JTAG_TBT_TMS_PCH0.49––
KBDLED_CATHODE10.66––
KBDLED_CATHODE20.65––
LCD_HPD_CONN0.764–101.50k Screen-side Unplugged
LCD_IRQ_L0.444–7.94M Screen-side Unplugged
LCD_PSR_EN0.52––
LCDBKLT_EN_LOL––
LCDBKLT_FB0.76––
LCDBKLT_FET_DRV0.63––
LCDBKLT_FET_DRV_R0.63––
LCDBKLT_SW0.48––
LCDBKLT_TB_XWR1.29––
LPC_AD_R<0>0.52––
LPC_AD_R<1>0.52––
LPC_AD_R<2>0.53––
LPC_AD_R<3>0.52––
LPC_AD<0>0.57––
LPC_AD<1>0.57––
LPC_AD<2>0.58––
LPC_AD<3>0.57––
LPC_CLK24M_SMC0.47––
LPC_CLK24M_SMC_R0.44––
LPC_FRAME_L0.57––
LPC_FRAME_R_L0.52––
LPC_PWRDWN_L0.68––
LPC_SERIRQ0.54––
LSUB_GAIN0.61––
LSUBIN_N0.59––
LSUBIN_P0.59––
MCP_DC_A4OL––
MCP_DC_AV1OL––
MCP_DC_AW1OL––
MCP_DC_AW63OL––
MCP_DC_AY60OL––
MCP_DC_B2OL––
MCP_EDP_RCOMP0.16––
MEM_B_DQ<37>0.27––
MEM_B_DQS_N<4>0.27––
MEM_B_DQS_P<4>0.27––
MEM_CAM_RESET_L0.44––
MEMVTT_PWR_EN0.52––
MIPI_CLK_CONN_N0.39––
MIPI_CLK_CONN_P0.39––
MIPI_CLK_N0.41––
MIPI_CLK_P0.41––
MIPI_DATA_CONN_N0.39––
MIPI_DATA_CONN_P0.39––
MIPI_DATA_N0.41––
MIPI_DATA_P0.41––
ODD_PWR_EN_L0.62––
P1V2_CAM_SRVLXC_PHASE0.29––
P1V05_DIV_VMONOL––
P1V5_DIV_VMONOL––
P1V05_EN_DOL––
P1V5_S0_FB0.77––
P1V5_S0_SW0.34––
P1V05_S0_VREF0.62––
P1V5CODEC_EN_DOL––
P1V05S0_AGND0.00––
P1V05S0_BOOT_RC0.61––
P1V05S0_DRVH0.60––
P1V05S0_DRVH_R0.63––
P1V05S0_DRVL0.43––
P1V05S0_EN0.45––
P1V5S0_EN0.75––
P1V05S0_FB0.68––
P1V05S0_IOUTOL––
P1V05S0_LL0.15––
P1V05S0_LL_SNUBOL––
P1V05S0_MODE0.52––
P1V05S0_PGOOD0.48––
P1V5S0_PGOOD0.53––
P1V05S0_TRIP0.74––
P1V05S0_VBST0.60––
P1V05S0_VDDQSNS0.16––
P1V05S0_VDDQSNS_R0.19––
P1V05S0_VTT0.56––
P1V05S0_VTTREF0.47––
P1V5S0SW_AUDIO_ENOL––
P1V05S3_EN0.49––
P1V05TBT_SW0.16––
P1V8S3_FB0.78––
P1V8S3_FB_R0.37––
P1V8S3_IOUTOL––
P1V8S3_PGOOD0.54––
P1V8S3_SW0.376––
P1V35_CAM_SRVLXD_PHASE0.26––
P3V3S0_EN0.70––
P3V3S0_EN_D0.73––
P3V3S0SW_SSD_FET_RAMP0.61––
P3V3S3_EN0.52––
P3V3S5_COMP20.73––
P3V3S5_COMP2_ROL––
P3V3S5_CSN20.14––
P3V3S5_CSP21.30––
P3V3S5_CSP2_R0.17––
P3V3S5_DRVH0.71––
P3V3S5_DRVL0.55––
P3V3S5_LL0.14––
P3V3S5_RF0.59––
P3V3S5_SNUBROL––
P3V3S5_TG0.71––
P3V3S5_VBST0.55––
P3V3S5_VFB20.58––
P3V3S5_VFB2_R0.17––
P3V3S5_VFB2_RR0.18––
P3V3SSD_VMON0.47––
P3V3SUS_EN0.60––
P3V42G3H_BOOST0.62––
P3V42G3H_FB0.71––
P3V42G3H_SHDN_L0.36––
P3V42G3H_SW0.31––
P5V_DIV_VMONOL––
P5V1_BIAS0.33––
P5V1_BOOST0.63––
P5V1_FB0.71––
P5V1_SW0.33––
P5V1_VIN0.60––
P5VP3V3_SKIPSEL0.48––
P5VP3V3_VREF20.48––
P5VP3V3_VREG30.56––
P5VS0_EN0.63––
P5VS0_EN_D0.75––
P5VS0_FET_RAMP0.69––
P5VS3_COMP10.73––
P5VS3_COMP1_ROL––
P5VS3_CSN10.39––
P5VS3_CSP11.30––
P5VS3_CSP1_R0.44––
P5VS3_DRVH0.94––
P5VS3_DRVL0.55––
P5VS3_EN0.45––
P5VS3_EN_DOL––
P5VS3_EN_RC0.53––
P5VS3_LL0.39––
P5VS3_PGOOD0.49––
P5VS3_SNUBROL––
P5VS3_TG0.95––
P5VS3_VBST0.62––
P5VS3_VFB10.58––
P5VS3_VFB1_R0.41––
P5VS3_VSW0.39––
P5VS4_EN0.55––
P5VS4_EN_D0.77––
P5VS5_FET_RAMP0.72––
PBUS_S0_VSENSEOL––
PBUS_S0_VSENSE_IN0.14––
PBUSVSENS_EN_L0.47––
PBUSVSENS_EN_L_DIVOL––
PCH_CLK24M_XTALIN0.78––
PCH_CLK24M_XTALOUT0.78––
PCH_CLK24M_XTALOUT_R0.78––
PCH_CLK32K_RTCX10.45––
PCH_DIFFCLK_BIASREF0.72––
PCH_DSWVRMEN0.79––
PCH_GSPI0_CLK0.50––
PCH_GSPI0_CS_L0.52––
PCH_GSPI0_MISO0.50––
PCH_GSPI0_MOSI0.54––
PCH_HSIO_PWR_EN0.51––
PCH_I2C0_SCL0.63––
PCH_I2C0_SDA0.62––
PCH_I2C1_SCL0.62––
PCH_INTRUDER_L0.79––
PCH_INTVRMEN0.79––
PCH_JTAGX0.05––
PCH_OPI_COMP0.05––
PCH_PCIE_RCOMP0.76––
PCH_PM_SLP_S0_L0.47––
PCH_SATA_RCOMP0.76––
PCH_SATALED_L0.62––
PCH_SMBALERT_L0.66––
PCH_SML1ALERT_L0.68––
PCH_SRTCRST_L0.79––
PCH_STRP_TOPBLK_SWP_L0.55––
PCH_SUSACK_L0.64––
PCH_SUSWARN_L0.65––
PCH_TBT_PCIE_RESET_L0.66––
PCH_TCO_TIMER_DISABLE0.54––
PCH_TD_IREF0.78––
PCH_TESTLOW_AK80.79––
PCH_TESTLOW_AL80.79––
PCH_TESTLOW_C340.78––
PCH_TESTLOW_C350.78––
PCH_UART1_TXD0.52––
PCH_USB_RBIAS0.02––
PCIE_AP_D2R_N0.38––
PCIE_AP_D2R_P0.38––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CAMERA_R2D_C_N0.38––
PCIE_CAMERA_R2D_C_P0.37––
PCIE_CLK100M_AP_CONN_N0.29––
PCIE_CLK100M_AP_CONN_P0.29––
PCIE_CLK100M_SSD_RC2_N0.30––
PCIE_CLK100M_SSD_RC2_P0.30––
PCIE_SSD_D2R_N<0>0.38––
PCIE_SSD_D2R_N<1>0.38––
PCIE_SSD_D2R_N<2>0.38––
PCIE_SSD_D2R_N<3>0.42––
PCIE_SSD_D2R_P<0>0.38––
PCIE_SSD_D2R_P<1>0.36––
PCIE_SSD_D2R_P<2>0.38––
PCIE_SSD_D2R_P<3>0.39––
PCIE_SSD_R2D_N<0>OL––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_N<2>OL––
PCIE_SSD_R2D_N<3>OL––
PCIE_SSD_R2D_P<0>OL––
PCIE_SSD_R2D_P<1>OL––
PCIE_SSD_R2D_P<2>OL––
PCIE_SSD_R2D_P<3>OL––
PCIE_TBT_D2R_N<0>0.38––
PCIE_TBT_D2R_P<0>0.39––
PCIE_WAKE_L0.55––
PD_CS4208_GPIO10.73––
PDCINVSENS_EN_L_DIVOL––
PLT_RESET_L0.53––
PLT_RST_BUF_L0.60––
PM_BATLOW_L0.51––
PM_CLK32K_SUSCLK_R0.615––
PM_CLKRUN_L0.57––
PM_PCH_PWROK0.66––
PM_PCH_SYS_PWROK0.74––
PM_PWRBTN_L0.57––
PM_RSMRST_L0.63––
PM_S0_PGOOD0.66––
PM_SLP_S0_L0.59––
PM_SLP_S3_BUF_L0.44––
PM_SLP_S3_L0.62––
PM_SLP_S3_R_L0.67––
PM_SLP_S4_BTMUX_L0.70––
PM_SLP_S4_L0.45––
PM_SLP_S5_L0.52––
PM_SLP_SUS_L0.60––
PM_THRMTRIP_L0.28––
PM_THRMTRIP_R_LOL––
PP0V6_S0_DDRVTT0.13––
PP0V6_S3_MEM_VREFCA_A0.35––
PP0V6_S3_MEM_VREFDQ_A0.39––
PP0V6_S3_MEM_VREFDQ_B0.40––
PP0V675_CAM_VREF0.57––
PP0V675_MEM_CAM_VREFCA0.46––
PP0V675_MEM_CAM_VREFDQ0.57––
PP1V2_CAM0.31––
PP1V2_CAM_PCIE_PVDD_FLT0.35––
PP1V2_CAM_PCIE_VDD_FLT0.35––
PP1V2_CAM_XTALPCIEVDD0.33––
PP1V2_S30.20––
PP1V2_S3_CPUDDR0.13––
PP1V2_S5_SMC_VDDC0.51––
PP1V05_S00.19––
PP1V5_S00.31––
PP1V5_S0_AUDIO_DIG0.36––
PP1V05_S0_PCH_VCC_ICC0.19––
PP1V05_S0_PCH_VCC_ICC_R0.19––
PP1V05_S0_PCH_VCCAPLL_OPI0.19––
PP1V05_S0_REG_R0.19––
PP1V5_S0SW_AUDIO_HDA0.34––
PP1V05_S0SW_PCH_HSIO0.23––
PP1V05_S0SW_PCH_VCCSATA3PLL0.24––
PP1V05_S0SW_PCH_VCCUSB3PLL0.23––
PP1V05_SUS0.30––
PP1V05_TBT0.17––
PP1V05_TBTCIO0.13––
PP1V05_TBTRDV0.14––
PP1V8_CAM0.50––
PP1V8_S30.36––
PP1V8_S3_REG_R0.376––
PP1V35_CAM0.27––
PP1V35_DDR_CLK0.26––
PP3V3_S00.32––
PP3V3_S0_AUDIO_ANALOG0.34––
PP3V3_S0_CPUTHMSNS_R0.37––
PP3V3_S0_EDP_R0.566–79.10k Screen-side Unplugged
PP3V3_S0_EDP_SW0.68––
PP3V3_S0_FET0.35––
PP3V3_S0_TBTTHMSNS_R0.37––
PP3V3_S0SW_SSD0.52––
PP3V3_S0SW_SSD_FET0.52––
PP3V3_S0SW_SSD_FLT0.52––
PP3V3_S30.51––
PP3V3_S3_FET_R0.57––
PP3V3_S3RS0_CAMERA0.32––
PP3V3_S3RS0_CAMERA_R0.32––
PP3V3_S40.41––
PP3V3_S4_FET_R0.45––
PP3V3_S4_TBT0.41––
PP3V3_S4_TBT_F0.42––
PP3V3_S4_TBTAPWR0.46––
PP3V3_S4_TBTBPWR0.46––
PP3V3_S4SW_SNS0.57––
PP3V3_S4SW_SNS_FET_R0.57––
PP3V3_S50.14––
PP3V3_S5_AVREF_SMC0.60––
PP3V3_S5_SMC_VDDA0.32––
PP3V3_S5RS3RS0_SYSCLKGEN0.14––
PP3V3_SUS3v34––
PP3V3_SUS_FET_R0.45––
PP3V3_TBTLC0.41––
PP3V3_TBTRDV0.55––
PP3V3RHV_S4_TBTAPWR0.56––
PP3V3RHV_S4_TBTAPWR_F0.56––
PP3V3RHV_S4_TBTBPWR0.56––
PP3V42_G3H0.296––
PP3V42_G3H_SMC_SPVSR0.32––
PP4V5_AUDIO_ANALOG0.41––
PP5V_S00.43––
PP5V_S0_AUDIO_AMP_L0.395––
PP5V_S0_AUDIO_AMP_R0.41––
PP5V_S0_BKLT_A0.46––
PP5V_S0_BKLT_D0.51––
PP5V_S0_CPUVR_VDD0.42––
PP5V_S0_FET0.47––
PP5V_S0_KBDBKLT_SW0.49––
PP5V_S30.39––
PP5V_S3_AUDIO_XW0.42––
PP5V_S3_LTUSB_A_ILIM0.52––
PP5V_S3RS0_ALSCAM_F0.42––
PP5V_S40.56––
PP5V_S4_TPAD_F0.56––
PP5V_S50.45––
PP5V1_CHGR_VDD0.32––
PP5V1_CHGR_VDDP0.32––
PP5VR3V3_SW_LCD0.530–7.19k Screen-side Unplugged
PP5VR3V3_SW_LCD_ISNS0.56––
PP5VR3V3_SW_LCD_UF0.56––
PP15V_TBT0.56––
PP18V5_DCIN_CONN_ROL––
PP18V5_DCIN_FUSE0.650 DC+Board+connected1.965––
PPBUS_G3H0.130––
PPBUS_G3H_R0.15––
PPBUS_S4_X239OL––
PPBUS_S5_HS_COMPUTING0.13––
PPBUS_S5_HS_OTHER3V30.13––
PPBUS_S5_HS_OTHER5V0.13––
PPDCIN_G3H0.650 DC%2bBoard%2bconnected1.965––
PPDCIN_G3H_CHGR0.590––
PPDCIN_G3H_INRUSH0.590––
PPDCIN_G3H_ISOLOL––
PPDDR_S3_REG_R0.127––
PPVBAT_G3H_CHGR_R0.130––
PPVBAT_G3H_CHGR_REG0.130––
PPVBAT_G3H_CONNOL––
PPVCC_S0_CPU0.02––
PPVCC_S0_CPU_PH10.01––
PPVCC_S0_CPU_PH20.01––
PPVCOMP_S0_CPU0.13––
PPVIN_G3H_P3V42G3H0.36––
PPVIN_S0_CPUVR_VIN0.14––
PPVIN_S0SW_LCDBKLT0.92––
PPVIN_S0SW_LCDBKLT_F0.19––
PPVIN_S0SW_LCDBKLT_R0.19––
PPVIN_S4_TPAD_FUSEOL––
PPVIN_SW_LCDBKLT_SW0.98––
PPVIN_SW_TBTBST0.47––
PPVOUT_S0_KBDBKLT0.63––
PPVOUT_S0_LCDBKLT1.114––
PPVOUT_S0_PCH_DCPRTC0.701.60–
PPVOUT_S5_PCH_DCPSUSBYP0.29––
PPVOUT_S5_PCH_DCPSUSBYP_R0.29––
PPVRTC_G3H0.44––
PPVTTDDR_S30.53––
PVIN_S4_TPAD_EN0.75––
PVIN_S4_TPAD_EN_L0.51––
PVIN_S4_TPAD_SSOL––
RSUB_GAIN0.59––
RSUBIN_N0.59––
RSUBIN_P0.60––
RTC_RESET_L0.79––
S0PGD_BJT_GND_R0.10––
S0PGD_COL––
S4_PWR_EN0.52––
S5_PWR_EN0.53––
S5_PWRGD0.58––
SD_PWR_EN0.53––
SD_RESET_L0.66––
SDCONN_STATE_CHANGE_RIO0.77––
SMBUS_PCH_CLK0.58––
SMBUS_PCH_DATA0.58––
SMBUS_SMC_0_S0_SCL0.690–321.00k Screen-side Unplugged
SMBUS_SMC_0_S0_SDA0.690–323.00k Screen-side Unplugged
SMBUS_SMC_1_S0_SCL0.55––
SMBUS_SMC_1_S0_SDA0.55––
SMBUS_SMC_2_S3_SCL0.71––
SMBUS_SMC_2_S3_SDA0.71––
SMBUS_SMC_3_SCL0.72––
SMBUS_SMC_3_SDA0.72––
SMBUS_SMC_5_G3_SCL0.490––
SMBUS_SMC_5_G3_SDA0.490––
SMC_ACTUATOR_DISABLE_L0.75––
SMC_ADAPTER_EN0.500––
SMC_BC_ACOK0.543.300–
SMC_BC_ACOK_VCC0.60––
SMC_BMON_COMP_ALERT_LOL––
SMC_BMON_DISCRETE_ISENSE0.74––
SMC_BMON_ISENSE0.73––
SMC_BOARDID0.74––
SMC_CAMERA_ISENSE0.74––
SMC_CLK32K0.620––
SMC_CPU_HI_ISENSE0.73––
SMC_CPU_IMON_ISENSE0.62––
SMC_CPU_ISENSE0.74––
SMC_CPU_VSENSE0.73––
SMC_CPUDDR_ISENSE0.74––
SMC_DCIN_ISENSE0.74––
SMC_DCIN_VSENSE0.73––
SMC_DDR_ISENSE0.74––
SMC_DDR1V8_ISENSE0.74––
SMC_DEBUGPRT_EN_L0.59––
SMC_DEBUGPRT_RX_L0.67––
SMC_DEBUGPRT_TX_L0.67––
SMC_DELAYED_PWRGD0.69––
SMC_DP_HPD_L0.74––
SMC_EXTAL0.77––
SMC_FAN_0_CTL0.75––
SMC_FAN_0_TACH0.75––
SMC_LCDBKLT_ISENSE0.74––
SMC_LCDPANEL_ISENSE0.74––
SMC_LID0.46––
SMC_LID_R0.45––
SMC_LRESET_L0.60––
SMC_MANUAL_RST_L0.67––
SMC_ONOFF_L0.590––
SMC_OOB1_D2R_CONN_L0.54––
SMC_OOB1_D2R_L0.68––
SMC_OOB1_R2D_CONN_L0.70––
SMC_OOB1_R2D_L0.50––
SMC_OTHER3V3_HI_ISENSE0.74––
SMC_OTHER5V_HI_ISENSE0.74––
SMC_PBUS_VSENSE0.73––
SMC_PCH_ISENSE0.74––
SMC_PCH_SUSACK_L0.64––
SMC_PCH_SUSWARN_L0.64––
SMC_PECI_L0.74––
SMC_PECI_L_R0.74––
SMC_PM_G2_EN0.53––
SMC_PME_S4_DARK_L0.63––
SMC_PME_S4_WAKE_L0.48––
SMC_PME_SDCONN0.63––
SMC_PP3V3S0_ISENSE0.74––
SMC_PP5VS0_ISENSE0.74––
SMC_PROCHOT0.74––
SMC_RESET_L0.51––
SMC_RX_L0.75––
SMC_S4_WAKESRC_EN0.74––
SMC_S5_PWRGD_VIN0.74––
SMC_SENSOR_ALERT_L0.73––
SMC_SENSOR_PWR_EN0.66––
SMC_SSD_ISENSE0.74––
SMC_SYS_KBDLED0.55––
SMC_TBT_ISENSE0.73––
SMC_TCK0.74––
SMC_TDI0.74––
SMC_TDO0.74––
SMC_THRMTRIP0.74––
SMC_TMS0.74––
SMC_TPAD_ISENSE0.74––
SMC_TPAD_RST_L0.47––
SMC_TPAD_VSENSE0.73––
SMC_TX_L0.74––
SMC_VCCIO_CPU_DIV20.73––
SMC_WAKE_L0.720––
SMC_WAKE_SCI_L0.51––
SMC_WIFI_PWR_EN0.68––
SMC_XTAL0.76––
SMC_XTAL_ROL––
SML_PCH_0_CLK0.65––
SML_PCH_0_DATA0.64––
SMS_INT_L0.74––
SPI_CLK0.56––
SPI_CS0_L0.56––
SPI_CS0_R_L0.57––
SPI_DESCRIPTOR_OVERRIDE1.30––
SPI_DESCRIPTOR_OVERRIDE_L0.74––
SPI_DESCRIPTOR_OVERRIDE_LS5V0.61––
SPI_IO2_R0.57––
SPI_IO3_R0.57––
SPI_MISO_R0.52––
SPI_MLB_CLK0.57––
SPI_MLB_CS_L0.62––
SPI_MLB_IO0_MOSI0.52––
SPI_MLB_IO1_MISO0.50––
SPI_MLB_IO2_WP_L0.52––
SPI_MLB_IO3_HOLD_L0.52––
SPI_MLBROM_CS_L0.65––
SPI_MOSI0.52––
SPKR_L_GAIN0.64––
SPKR_R_GAIN0.62––
SPKR_SHUTDOWN0.55––
SPKRAMP_LIN_N0.63––
SPKRAMP_LIN_P0.63––
SPKRAMP_RIN_N0.62––
SPKRAMP_RIN_P0.62––
SPKRCONN_L_ID0.73––
SPKRCONN_L_OUT_N0.52––
SPKRCONN_L_OUT_P0.52––
SPKRCONN_R_ID0.73––
SPKRCONN_R_OUT_N0.51––
SPKRCONN_R_OUT_P0.51––
SPKRCONN_SL_OUT_N0.62––
SPKRCONN_SL_OUT_P0.62––
SPKRCONN_SR_OUT_N0.61––
SPKRCONN_SR_OUT_P0.61––
SSD_BOOT0.61––
SSD_BOOT_R0.47––
SSD_CLKREQ_CONN_L0.56––
SSD_CLKREQ_CONN_R_L0.47––
SSD_CLKREQ_L0.56––
SSD_CLKREQ_R_L0.47––
SSD_PCIE_SEL_L0.00––
SSD_PWR_EN0.43––
SSD_RESET_CONN_L0.47––
SSD_SR_EN_L0.51––
SUS_PGOOD_CT0.63––
SYS_DETECT_L1.630––
SYS_ONEWIRE0.68––
SYS_PWROK_R0.67––
SYSCLK_CLK25M_CAMERA0.44––
SYSCLK_CLK25M_TBT0.43––
SYSCLK_CLK25M_TBT_R0.63––
SYSCLK_CLK25M_X10.44––
SYSCLK_CLK25M_X20.45––
SYSCLK_CLK25M_X2_R0.44––
TBT_A_CONFIG1_RC0.83––
TBT_A_HV_EN0.49––
TBT_B_CONFIG1_RC0.83––
TBT_B_CONFIG2_RC0.81––
TBT_B_DP_PWRDN0.80––
TBT_B_HV_EN0.48––
TBT_BATLOW_L0.80––
TBT_CIO_PLUG_EVENT_L0.52––
TBT_DDC_XBAR_EN0.49––
TBT_DDC_XBAR_EN_L0.81––
TBT_DFT_STRAP_10.56––
TBT_EN_CIO_PWR0.61––
TBT_GPIO70.62––
TBT_MONOBSN0.20––
TBT_MONOBSP0.20––
TBT_POC_RESET_L0.52––
TBT_PWR_EN0.53––
TBT_PWR_ON_POC_RST_L0.74––
TBT_PWR_REQ_L0.64––
TBT_RBIAS0.79––
TBT_ROM_SECURITY_XOR0.57––
TBT_SPI_CLK0.59––
TBT_SPI_CS_L0.64––
TBT_SPI_MISO0.66––
TBT_SPI_MOSI0.59––
TBT_TEST_EN0.11––
TBT_TEST_PWR_GOOD0.66––
TBT_TMU_CLK_OUT0.57––
TBTACONN_20_RC0.57––
TBTAPWRSW_ISET_S00.48––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.48––
TBTAPWRSW_ISET_S3_ROL––
TBTAPWRSW_ISET_V3P30.48––
TBTBCONN_20_RC0.58––
TBTBPWRSW_ISET_S00.48––
TBTBPWRSW_ISET_S0_ROL––
TBTBPWRSW_ISET_S30.48––
TBTBPWRSW_ISET_S3_ROL––
TBTBPWRSW_ISET_V3P30.48––
TBTBST_BOOST0.52––
TBTBST_EN_UVLO0.64––
TBTBST_FBXOL––
TBTBST_INTVCC0.58––
TBTBST_PWREN_DIV_LOL––
TBTBST_PWREN_L0.51––
TBTBST_RT0.67––
TBTBST_SHDN_DIV0.62––
TBTBST_SNS10.00––
TBTBST_SNS20.00––
TBTBST_SS0.67––
TBTBST_VC0.70––
TBTBST_VC_RCOL––
TBTBST_VSNS0.57––
TBTDP_AUXIO_EN0.77––
TBTPOCRST_CT0.74––
TBTPOCRST_MR_L0.55––
TBTPOCRST_SENSE1.41––
TBTROM_HOLD_L0.72––
TBTROM_WP_L0.72––
TBTTHMSNS_ALERT_LOL––
TBTTHMSNS_D1_N0.00––
TBTTHMSNS_D1_P0.72––
TBTTHMSNS_THM_LOL––
TP_CAM_JTAG_TRST_L0.77––
TP_CAM_LV_JTAG_TCK0.77––
TP_CAM_LV_JTAG_TDI0.77––
TP_CAM_LV_JTAG_TDO0.77––
TP_CAM_LV_JTAG_TMS0.77––
TP_CAM_LV_JTAG_TRSTN0.77––
TP_CAM_TEST_MODE00.76––
TP_CAM_TEST_MODE10.77––
TP_CAM_TEST_MODE20.77––
TP_CPU_RSVDN610.37––
TP_CS4208_HDA_SDOUT10.69––
TP_EDP_DISP_UTIL0.42––
TP_LPC_CLK24M_LPCPLUS0.50––
TP_MCP_RSVD_AU630.37––
TP_MCP_RSVD_AV630.37––
TP_MCP_RSVD_C620.37––
TP_MCP_RSVD_C630.37––
TP_MCP_RSVD_L600.36––
TPAD_ACTUATOR_EN_L0.84––
TPAD_ACTUATOR_EN_RC_L0.75––
TPAD_ACTUATOR_THRMTRIP_L0.74––
TPAD_SPI_CLK_R0.53––
TPAD_SPI_CS_CONN_L0.80––
TPAD_SPI_CS_L0.55––
TPAD_SPI_IF_EN0.52––
TPAD_SPI_IF_EN_CONN0.74––
TPAD_SPI_IF_EN_R0.68––
TPAD_SPI_IF_EN_R_C0.71––
TPAD_SPI_INT_GPIO28_L0.48––
TPAD_SPI_INT_GPIO46_L0.48––
TPAD_SPI_INT_L0.47––
TPAD_SPI_MISO_R0.50––
TPAD_SPI_MOSI_R0.54––
TPAD_USB_IF_EN0.62––
TPAD_VBUS_EN0.74––
TPAD_VBUS_EN_R0.68––
TPAD_VBUS_EN_R_C0.71––
USB_BT_CONN_N0.78––
USB_BT_CONN_P0.78––
USB_EXTB_N0.44––
USB_EXTB_P0.44––
USB_ILIM0.55––
USB_ILIM_LOL––
USB_PWR_EN0.49––
USB_TPAD_N0.43––
USB_TPAD_P0.43––
USB2_EXTA_MUXED_F_N0v65––
USB2_EXTA_MUXED_F_P0v65––
USB2_EXTA_MUXED_N0v65––
USB2_EXTA_MUXED_P0v65––
USB3_EXTB_D2R_N0.37––
USB3_EXTB_D2R_P0.38––
USB3_EXTB_R2D_C_N0.37––
USB3_EXTB_R2D_C_P0.36––
USB3RPCIE_SD_D2R_N0.37––
USB3RPCIE_SD_D2R_P0.38––
USB3RPCIE_SD_R2D_C_N0.36––
USB3RPCIE_SD_R2D_C_P0.36––
VHP_FILTN0.93––
VMON_3V3_DIVOL––
VMON_5V_DIVOL––
VMON_Q2_BASEOL––
VMON_Q3_BASEOL––
VMON_Q4_BASE1.33––
VOUT_X239_DIVOL––
VOUT_X239_XWOL––
VREF_DAC0.75––
WIFI_EVENT_L0.74––
WOL_EN0.64––
WS_CONTROL_KBD0.47––
WS_CONTROL_KEY0.45––
WS_KBD_ONOFF_LOL––
WS_KBD10.61––
WS_KBD20.60––
WS_KBD30.61––
WS_KBD40.61––
WS_KBD50.62––
WS_KBD60.61––
WS_KBD70.61––
WS_KBD80.61––
WS_KBD90.61––
WS_KBD100.54––
WS_KBD110.61––
WS_KBD120.60––
WS_KBD130.61––
WS_KBD140.61––
WS_KBD15_C0.54––
WS_KBD15_CAP0.60––
WS_KBD16_NUM0.60––
WS_KBD170.54––
WS_KBD180.53––
WS_KBD190.53––
WS_KBD200.60––
WS_KBD210.51––
WS_KBD220.52––
WS_KBD230.60––
WS_LEFT_OPTION_KBD0.47––
WS_LEFT_OPTION_KEY0.46––
WS_LEFT_SHIFT_KBD0.47––
WS_LEFT_SHIFT_KEY0.46––
XDP_BPM_L<0>0.30––
XDP_BPM_L<1>0.30––
XDP_BPM_L<2>0.32––
XDP_BPM_L<3>0.31––
XDP_BPM_L<4>0.36––
XDP_BPM_L<5>0.31––
XDP_BPM_L<7>0.38––
XDP_CPU_PRDY_L0.28––
XDP_CPU_PREQ_L0.28––
XDP_CPU_PRESENT_L1.28––
XDP_CPU_PWRBTN_L0.56––
XDP_CPU_TCK0.05––
XDP_CPU_TDI0.30––
XDP_CPU_TDO0.23––
XDP_CPU_TMS0.30––
XDP_CPU_VCCST_PWRGD1.68––
XDP_CPUPCH_TRST_L0.30––
XDP_CPURST_L1.53––
XDP_DBRESET_L0.63––
XDP_JTAG_CPU_ISOL_L0.69––
XDP_LPCPLUS_GPIO0.51––
XDP_MLB_RAMCFG00.51––
XDP_PCH_GPIO170.49––
XDP_PCH_GPIO760.54––
XDP_PCH_TCK0.39––
XDP_PCH_TDI0.35––
XDP_PCH_TDO0.30––
XDP_PCH_TMS0.35––
XDP_SSD_PCIE0_SEL_L0.45––
XDP_SSD_PCIE1_SEL_L0.44––
XDP_SSD_PCIE2_SEL_L0.47––
XDP_SSD_PCIE3_SEL_L0.45––
XDP_SYS_PWROK0.73––
XDP_TRST_L0.82––
XDP_USB_EXTA_OC_L0.50––
XDP_USB_EXTB_OC_L0.55––
XDP_USB_EXTD_OC_L0.54––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-4924?

OpenBoardData's known-good values for PPBUS_G3H on the 820-4924: diode 0.130. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-4924?

OpenBoardData's known-good values for PP3V42_G3H on the 820-4924: diode 0.296. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-4924?

OpenBoardData's known-good values for PP5V_S5 on the 820-4924: diode 0.45. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-4924 board?

Open your own 820-4924 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License