Apple laptop board · OpenBoardData

820-2850 known-good readings

Known-good readings for the Apple laptop board 820-2850: 221 nets, including 21 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 21 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-2850.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 21 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 2

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.39––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, indicated by the G3H suffix in its name. The archive lists a known-good diode reading of 0.39 to ground for this net; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from PP3V42_G3H to ground, then measure the voltage with power applied. A diode reading far from 0.39 usually points to a short or a faulty component on the rail, but confirm with more measurements before replacing anything.

PPBUS_G3H0.47––
AI: what PPBUS_G3H is and how to check it

PPBUS_G3H is the main battery/charger bus rail; the "G3H" suffix, from the name, marks it as an always-on rail. The archive lists one known-good reading: diode mode 0.47. Check it with the board unpowered, black probe on ground and red on the rail, then measure its voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.47 usually points to a short or a leaky part on the rail, but one reading isn't proof — confirm before replacing anything.

S5 and SUS: standby 1

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.14––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply. The archive lists a diode reading of 0.14 to ground for this net (no condition recorded), and there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.14 usually points to a short or a leaky load on the rail, but confirm with a second measurement before condemning anything.

S3: memory 11

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V5_S30.45––
AI: what PP1V5_S3 is and how to check it

PP1V5_S3 is a 1.5 V rail in the S3 (memory) startup stage, judging from its name. The only known-good reading here is a diode value of 0.45; no known-good voltage is listed. Check it with the board unpowered in diode mode from PP1V5_S3 to ground, then power up and measure the voltage. A diode reading far from 0.45 usually points to a short or leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_S30.37––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that, from its name, belongs to the S3 (memory) startup stage on this 820-2850. The only known-good reading here is a diode value of 0.37 to ground; there is no known-good voltage reading in this data.

  • Check it with the board unpowered: diode mode, red probe on ground, black probe on the PP3V3_S3 test point or a known PP3V3_S3 node.
  • Then power the board and measure the voltage on the same point.

A diode reading far from 0.37 usually points to a short or a leaky part on that rail, but a small difference can be normal, so compare against a matching net or a known-good board before condemning anything. With no known-good voltage listed, judge the powered reading against what a 3.3 V rail should show and against the rest of the S3 sequence.

PP3V3_S3_BT_F0.37––
AI: what PP3V3_S3_BT_F is and how to check it

PP3V3_S3_BT_F is a 3.3 V rail; the S3 in its name marks it as a memory-stage rail, and BT_F suggests it feeds the Bluetooth section (both from the name, not from board data). The only known-good reading here is a diode value of 0.37 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.37 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part; compare against a matching rail or a known-good board before replacing anything.

PP5V_S30.42––
AI: what PP5V_S3 is and how to check it

PP5V_S3 is a 5 V rail; the S3 suffix comes from its name and marks it as a memory (S3) startup-stage rail. The only known-good reading here is diode mode 0.42 to ground, with no condition recorded. Check it with the board unpowered in diode mode from PP5V_S3 to ground, then measure its voltage with power applied and the board brought out of standby. No known-good voltage reading is recorded for this rail, so compare against a matching 5 V rail or a known-good board. A diode reading far below 0.42 suggests a short or leaky load on the rail; a much higher one suggests an open path, but confirm with the voltage measurement before replacing anything.

PP5V_S3_ALSCAMERA_F0.41––
AI: what PP5V_S3_ALSCAMERA_F is and how to check it
  • What it is: From its name, PP5V_S3_ALSCAMERA_F is a 5 V rail that comes up at the S3 (memory/suspend-to-RAM) stage and feeds the camera circuit. That's inferred from the name only; the parts on the net aren't documented here.
  • Known-good reading: diode 0.41 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.41; then power up and measure the voltage, which should be about 5 V once the board reaches S3.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a correct diode reading with no voltage points upstream, to the rail's enable or supply. Confirm with a second measurement before replacing anything.
PP5V_S3_DDRREG_V5FILT0.42––
AI: what PP5V_S3_DDRREG_V5FILT is and how to check it

PP5V_S3_DDRREG_V5FILT is a 5 V memory rail: the "5V" and "S3" (memory) parts come from the name, and "DDRREG" suggests it feeds DDR memory regulation (general interpretation, not from board data). The only known-good reading here is a diode value of 0.42 to ground; no known-good voltage reading is recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and the board at S3. A diode reading far below 0.42 usually points to a short or a low-impedance load on the rail, but one reading isn't proof a part is bad, so compare against a matching net or a known-good board before replacing anything.

PP5V_S3_IR_R0.43––
AI: what PP5V_S3_IR_R is and how to check it

PP5V_S3_IR_R is a 5 V rail that, from its name, belongs to the S3 (memory/suspend) power state; the "IR_R" suffix is not explained by the available data. The only known-good reading is a diode value of 0.43 to ground, with no condition recorded; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and compare against a matching rail or a known-good board. A diode reading far from 0.43 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S3_RTUSB_A_F0.51––
AI: what PP5V_S3_RTUSB_A_F is and how to check it

PP5V_S3_RTUSB_A_F is a 5 V rail that, from its name, is switched in the S3 (memory/suspend) power state and feeds the right-side USB-A port. The only known-good reading here is a diode value of 0.51 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.51 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S3_RTUSB_B_F0.56––
AI: what PP5V_S3_RTUSB_B_F is and how to check it

PP5V_S3_RTUSB_B_F is a 5 V rail; the S3 in the name indicates it belongs to the memory (S3) power state, and RTUSB_B suggests it feeds a USB path. The only known-good reading here is a diode value of 0.56 to ground, with no condition recorded; no known-good voltage reading is available.

To check it, power the board off and measure diode mode from the rail to ground, then apply power and measure the voltage. A diode reading far below 0.56 usually points to a short or a leaky load on the rail; a much higher or open reading points to a broken path. Treat the 0.56 as a guide only, since readings vary with board state.

PP18V5_S30.71––
AI: what PP18V5_S3 is and how to check it

PP18V5_S3 is a switched 18.5 V rail; the S3 suffix indicates the memory power state (from the name). The archive lists one known-good diode reading of 0.71 to ground, with no condition given. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in S3. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.71 usually points to a short or leaky part on the rail; confirm with voltage and resistance before replacing anything.

PPVTTDDR_S30.52––
AI: what PPVTTDDR_S3 is and how to check it

PPVTTDDR_S3 is a memory-related rail, judged from its name: the S3 stage and DDR termination (VTT) suggest it feeds the memory's termination supply. The archive lists one known-good diode reading, 0.52, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.52 usually points to a short or a damaged part on that rail, but a single reading doesn't confirm a fault, so compare with a matching net or a known-good board before replacing anything.

S0: running 7

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP0V75_S0_DDRVTT0.51––
AI: what PP0V75_S0_DDRVTT is and how to check it

PP0V75_S0_DDRVTT is the 0.75 V DDR termination rail; the name indicates 0.75 V and the S0 state (running), and that reading is from the name rather than a schematic. The archive lists a known-good diode reading of 0.51 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage, which should sit near 0.75 V. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.51 usually points to a short or a faulty part on the rail, but confirm with the voltage and further checks before replacing anything.

PP1V8R1V55_S0GPU_ISNS_R0.090––
AI: what PP1V8R1V55_S0GPU_ISNS_R is and how to check it
  • What it is: From the name, PP1V8R1V55_S0GPU_ISNS_R is a GPU-related sense (ISNS) rail on the 820-2850, with S0 meaning the running state. The name suggests it tracks GPU supply current or voltage; the exact circuit isn't in the available data.
  • Known-good reading: diode 0.090 to ground (community archive, guide only). No known-good voltage or resistance reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much higher or open diode reading usually points to a broken trace or missing connection; a short to ground points to a failed part on that net. Confirm with a second measurement before replacing anything.
PP3V3_S00.29––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, as the name indicates. The only known-good reading here is a diode value of 0.29; no known-good voltage is recorded.

  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.29.
  • Then power the board and measure the voltage on the rail.
  • A diode reading far from 0.29 usually points to a short or a damaged component on that rail; a missing or low voltage under power points to the supply or enable side.

These readings are community guides and vary with board state, so treat a small difference as normal before suspecting a part.

PP5V_S00.41––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is up in the S0 (running) state, judged from its name; the data doesn't list which parts sit on it. The only known-good reading here is diode 0.41 to ground, with no condition noted, and there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from PP5V_S0 to ground, then power up and measure the voltage. A diode reading far from 0.41 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PP5V_S0_HDD_FLT0.41––
AI: what PP5V_S0_HDD_FLT is and how to check it

PP5V_S0_HDD_FLT is a 5 V rail that, from its name, is switched in the S0 (running) state and feeds the HDD circuit, with "FLT" suggesting a filtered or fault-related branch. The archive lists a known-good diode reading of 0.41 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage in S0. A diode reading far from 0.41 usually points to a short or leaky component on that rail, but one reading isn't proof, so confirm before replacing anything.

PPVCORE_S0_CPU0.08 2.5GHz i5–102.15R 2.5GHz i5
AI: what PPVCORE_S0_CPU is and how to check it

PPVCORE_S0_CPU — reference note

  • What it is: the CPU core power rail. The S0 in the name indicates the running state, and VCORE indicates the CPU core supply; this is from the name only.
  • Known-good readings: diode 0.08 and resistance 102.15R, both recorded on a 2.5GHz i5. These come from community contributions and are a guide, not a guarantee.
  • How to check: with the board unpowered, measure diode mode from the rail to ground, then measure resistance to ground. Then power the board and measure the voltage on the rail.
  • No known-good voltage is recorded for this rail, so compare against a known-good board or the expected core voltage for the CPU.
  • If a reading is far off: a diode or resistance far below the known-good value usually points to a short or a failing component on the rail, but one reading alone doesn't confirm a bad part. Recheck before replacing anything.
PPVOUT_S0_LCDBKLT0.63––
AI: what PPVOUT_S0_LCDBKLT is and how to check it

PPVOUT_S0_LCDBKLT is the LCD backlight output rail; the S0 in the name indicates it belongs to the running state, and the LCDBKLT part marks it as the backlight boost output. The only known-good reading here is a diode value of 0.63 to ground, with no condition recorded; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the DC voltage on it. A diode reading far below 0.63 usually points to a short or leaky component on the rail, while a far higher or open reading points to a broken connection; confirm with a voltage check under power before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
AP_CLKREQ_Q_L1.40––
AP_RESET_CONN_L0.59––
CHGR_ACIN0.54––
CHGR_AGATE0.66––
CHGR_AMON0.73––
CHGR_BGATE0.68––
CHGR_BMON0.74––
CHGR_BOOT0.59––
CHGR_CELL0.72––
CHGR_CSI_N0.64––
CHGR_CSI_P0.63––
CHGR_CSO_N0.48––
CHGR_CSO_P0.47––
CHGR_DCIN0.63––
CHGR_ICOMP0.73––
CHGR_LGATE0.47––
CHGR_PHASE0.47––
CHGR_RST_L0.51––
CHGR_SGATE0.65––
CHGR_UGATE0.93––
CHGR_VCOMP0.73––
CHGR_VFRQ0.53––
CHGR_VNEG0.54––
CONN_USB2_BT_N0.67––
CONN_USB2_BT_P0.67––
CPUIMVP_PHASE10.08 2.5GHz i5–102.15R 2.5GHz i5
CPUIMVP_PHASE2––94.77R 2.5GHz i5
CPUTHMSNS_ALERT_L0.00––
DDRREG_CS0.52––
DDRREG_CSGND0.00––
DDRREG_DRVH0.88––
DDRREG_DRVL0.44––
DDRREG_EN0.52––
DDRREG_FB0.52––
DDRREG_FB_XW0.44––
DDRREG_LL0.44––
DDRREG_PGOOD0.51––
DDRREG_VBST0.62––
DDRREG_VTTSNS0.50––
FAN_RT_PWM1.12––
FAN_RT_TACHOL––
FB_1V8_S0_LL0.090––
GFX_DPRSLPVR0.28––
GFX_VID<0>0.28––
GFX_VID<1>0.28––
GFX_VID<2>0.28––
GFX_VID<3>0.28––
GFX_VID<4>0.28––
GFX_VID<5>0.28––
GFX_VID<6>0.28––
GFX_VR_EN0.27––
GFX_VSENSE_N0.01––
GFX_VSENSE_P0.12––
GFXIMVP_CS_N0.13––
GFXIMVP_CS_P0.13––
GFXIMVP_DROOP0.72––
GFXIMVP_IMON0.72––
GFXIMVP_IMONC0.65––
GFXIMVP_ISLEW0.73––
GFXIMVP_LGATE0.39––
GFXIMVP_PGOOD0.65––
GFXIMVP_PHASE0.12––
GFXIMVP_THERM0.73––
GFXIMVP_TONSEL0.71––
GFXIMVP_UGATE0.63––
GFXIMVP_V5FILT0.41––
GFXIMVP_VBST0.59––
GFXIMVP_VREF0.64––
GFXIMVP_VREF_R0.64––
GFXIMVP6_RBIAS0.00––
GND_CHGR_AGND0.01––
GND_DDRREG_SGND0.00––
GND_GFXIMVP_AGND0.01––
IR_RX_OUT0.79––
KBDLED_ANODE0.62––
LED_RETURN_10.64––
LED_RETURN_20.64––
LED_RETURN_30.64––
LED_RETURN_40.64––
LED_RETURN_50.64––
LED_RETURN_60.64––
LVDS_CONN_A_CLK_F_N0.75––
LVDS_CONN_A_CLK_F_P0.75––
LVDS_CONN_A_DATA_N<0>0.74––
LVDS_CONN_A_DATA_N<1>0.74––
LVDS_CONN_A_DATA_N<2>0.74––
LVDS_CONN_A_DATA_P<0>0.74––
LVDS_CONN_A_DATA_P<1>0.75––
LVDS_CONN_A_DATA_P<2>0.74––
LVDS_CONN_B_CLK_F_N0.74––
LVDS_CONN_B_CLK_F_P0.75––
LVDS_CONN_B_DATA_N<0>0.74––
LVDS_CONN_B_DATA_N<1>0.74––
LVDS_CONN_B_DATA_N<2>0.74––
LVDS_CONN_B_DATA_P<0>0.74––
LVDS_CONN_B_DATA_P<1>0.75––
LVDS_CONN_B_DATA_P<2>0.75––
LVDS_DDC_CLK0.48––
LVDS_DDC_DATA0.48––
MEMVTT_EN0.59––
PCIE_AP_D2R_N0.40––
PCIE_AP_D2R_P0.40––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_CONN_N0.38––
PCIE_CLK100M_AP_CONN_P0.38––
PCIE_WAKE_L0.59––
PICKB_L0.68––
PP0V75_S0_DDRVTT0.51––
PP1V5_S30.45––
PP1V8R1V55_S0GPU_ISNS_R0.090––
PP3V3_S00.29––
PP3V3_S30.37––
PP3V3_S3_BT_F0.37––
PP3V3_S50.14––
PP3V3_SW_LCD0.59––
PP3V3_WLANOL––
PP3V42_G3H0.39––
PP5V_S00.41––
PP5V_S0_HDD_FLT0.41––
PP5V_S30.42––
PP5V_S3_ALSCAMERA_F0.41––
PP5V_S3_DDRREG_V5FILT0.42––
PP5V_S3_IR_R0.43––
PP5V_S3_RTUSB_A_F0.51––
PP5V_S3_RTUSB_B_F0.56––
PP5V_SW_ODDOL––
PP5V1_CHGR_VDD0.47––
PP5V1_CHGR_VDDP0.47––
PP18V5_S30.71––
PPBUS_G3H0.47––
PPVCORE_S0_CPU0.08 2.5GHz i5–102.15R 2.5GHz i5
PPVOUT_S0_LCDBKLT0.63––
PPVTTDDR_S30.52––
PSOC_F_CS_L0.70––
PSOC_MISO0.70––
PSOC_MOSI0.70––
PSOC_SCLK0.70––
SATA_HDD_D2R_C_NOL––
SATA_HDD_D2R_C_POL––
SATA_HDD_R2D_NOL––
SATA_HDD_R2D_POL––
SATA_ODD_D2R_UF_NOL––
SATA_ODD_D2R_UF_POL––
SATA_ODD_R2D_NOL––
SATA_ODD_R2D_POL––
SMBUS_SMC_A_S3_SCL0.57––
SMBUS_SMC_A_S3_SDA0.57––
SMBUS_SMC_BSA_SCL0.52––
SMBUS_SMC_BSA_SDA0.52––
SMC_BC_ACOK0.51––
SMC_BIL_BUTTON_L0.71––
SMC_KDBLED_PRESENT_L4.61––
SMC_LID_R0.80––
SMC_ODD_DETECT0.71––
SPI_MLB_CLK0.60––
SPI_MLB_CS_L0.59––
SPI_MLB_MISO0.51––
SPI_MLB_MOSI0.60––
SPI_WP_L0.70––
SPIROM_USE_MLB0.58––
SPKRCONN_R_OUT_N0.48––
SPKRCONN_R_OUT_P0.48––
SPKRCONN_S_OUT_N0.47––
SPKRCONN_S_OUT_P0.47––
SYS_LED_ANODE_ROL––
UNCONNECTED_180.53––
UNCONNECTED_190.50––
UNCONNECTED_45OL––
UNCONNECTED_46OL––
UNCONNECTED_47OL––
UNCONNECTED_48OL––
UNCONNECTED_49OL––
UNCONNECTED_215OL––
UNCONNECTED_216OL––
UNCONNECTED_220OL––
UNCONNECTED_276OL––
UNCONNECTED_277OL––
USB_CAMERA_CONN_N0.66––
USB_CAMERA_CONN_P0.66––
USB_LT2_N0.65––
USB_LT2_P0.66––
USB2_LT1_N0.56––
USB2_LT1_P0.58––
WS_CONTROL_KBDOL––
WS_KBD_ONOFF_L1.53––
WS_KBD10.71––
WS_KBD20.71––
WS_KBD30.71––
WS_KBD40.71––
WS_KBD50.71––
WS_KBD60.71––
WS_KBD70.71––
WS_KBD80.71––
WS_KBD90.71––
WS_KBD100.71––
WS_KBD110.71––
WS_KBD120.71––
WS_KBD130.71––
WS_KBD140.71––
WS_KBD15_CAP1.10––
WS_KBD16_NUMOL––
WS_KBD170.71––
WS_KBD180.70––
WS_KBD190.71––
WS_KBD200.71––
WS_KBD210.71––
WS_KBD220.71––
WS_KBD230.71––
WS_LEFT_OPTION_KBDOL––
WS_LEFT_SHIFT_KBD0.58––
Z2_BOOST_EN1.23––
Z2_CLKIN0.71––
Z2_CS_L0.70––
Z2_DEBUG30.70––
Z2_HOST_INTN0.70––
Z2_KEY_ACT_L0.70––
Z2_MISO0.70––
Z2_MOSI0.70––
Z2_RESET0.71––
Z2_SCLK0.71––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PPBUS_G3H read on the 820-2850?

OpenBoardData's known-good values for PPBUS_G3H on the 820-2850: diode 0.47. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V42_G3H read on the 820-2850?

OpenBoardData's known-good values for PP3V42_G3H on the 820-2850: diode 0.39. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-2850?

OpenBoardData's known-good values for PP3V3_S5 on the 820-2850: diode 0.14. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-2850 board?

Open your own 820-2850 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License