// guide
Known-good readings: how to measure a logic board and compare
A known-good reading is what a working board shows on the same net. Find your board number (820-xxxxx on Apple boards), look it up for free, then measure with the board unpowered in diode mode, one probe on ground and the other on the rail. Close to the known-good value is fine; near zero points to a short to ground; OL can mean an open path. Then check voltages stage by stage as the board powers up.

You probe a rail and the meter says 0.39. Good or bad? The number only means something next to what a working board shows on the same net. That’s a known-good reading.
Look up your board by number · Open your board file in the free viewer
The three readings
- Diode (diode mode), board unpowered: whether a rail is shorted, leaky or open. The fastest first check.
- Voltage, board powered: whether a rail actually comes up, and at the right level.
- Resistance to ground, board unpowered: a second check on a short. Varies more from meter to meter.
1. Find your board’s known-good values
Apple prints the board number on the logic board: 820- and a few digits, as in 820-00165. Look it up on the boards page. Each board’s page lists every power rail by startup stage with its known-good diode, voltage and resistance values, every other net with a reading, and the repair notes. The data comes from OpenBoardData, a community archive. New and changed boards are added every week.
2. Take diode readings first
- Disconnect the battery and the charger.
- Set the meter to diode mode.
- Red probe on ground (a screw hole or a shield), black probe on the rail. Touch the rail at a capacitor or a test point.
- Compare with the known-good value.
| You read | Likely meaning |
|---|---|
| Close to known-good | The rail is fine. Move on. |
| Near 0 | Shorted to ground, often a failed capacitor or chip on that rail. |
| Clearly lower, not 0 | A leaky part on the rail. |
| OL | Open path: a missing part, a lifted pad, or the probe isn’t on the rail. |
Probe direction matters: swapping the probes gives a different number. Measure one rail you trust first, and check your meter agrees with the known-good value before you trust the rest.
3. Then check voltages, stage by stage
Apple writes the power state into each rail’s name, so the names tell you the order a board comes up:
- G3H: always on, as soon as power is connected (
PPBUS_G3H,PP3V42_G3H) - S5 and SUS: standby (
PP3V3_S5) - S4 and S3: memory kept alive in sleep
- S0: only when the machine runs (
PP3V3_S0)
Work through them in that order. The first stage that’s missing is where to look: its enable signal or its regulator. More in Trace the power-up sequence on a MacBook board.
An example: 820-00165
Known-good values from OpenBoardData for four rails on the 820-00165:
| Rail | Stage | Diode | Voltage |
|---|---|---|---|
PPBUS_G3H |
G3H | 0.128 | 8.6 V |
PP3V42_G3H |
G3H | 0.320 | 3.4 V |
PP3V3_S5 |
S5 | 0.335 | 3.3 V |
PP3V3_S0 |
S0 | 0.390 | 3.3 V |
The same rail name can read differently on another board. PPBUS_G3H is 8.6 V here, as on other two-cell boards, and about 12.2 to 13.1 V on three-cell ones, where its diode reading is higher too. So a 0.13 can be perfectly normal. Always compare with your own board’s number. See PPBUS_G3H on 33 MacBook boards.
Why your reading can differ a little
- The meter. Diode readings vary slightly between meters.
- The board variant. Some readings are taken with a stated condition, such as a memory size or CPU. The board pages show it.
- The board’s state. With or without the trackpad, keyboard or SSD connected.
Treat the values as a guide, and the schematic as the final word.
Faster with the board file open
Open your boardview file in the free Board Viewer and name it with the board number, as in 820-00165.brd:
- Readings on the pins. Hover over a pin to see its known-good values, and type your meter’s reading to compare.
- Power AI. Draws the rails on the board, stage by stage.
- Ask AI. Click a part or net and ask about it. The answer uses the board’s readings and notes.
Nothing to install, and the file stays on your computer.
Add your own readings
Measured a working board? Share the values on OpenBoardData so the next person has them. They reach these pages with the next weekly update.
More
Frequently asked questions
What is a known-good reading?
The value a working board shows on a net: its diode-mode reading, its voltage when powered, or its resistance to ground. On its own a meter reading says little; next to the known-good value for the same board it shows where a faulty board differs.
Where do I find my board number?
On Apple boards it's printed on the logic board itself and starts with 820-, as in 820-00165 or 820-3115. Look it up on our boards page to see its known-good readings, power rails by startup stage and repair notes.
Which probe goes on ground for a diode-mode reading?
In Mac board repair the usual way is red probe on ground and black probe on the rail, with the board unpowered. Swapping the probes changes the number, so measure a known rail first and check you get a value close to the known-good one before you trust the rest.
What does OL mean in diode mode?
OL (over limit) means the meter sees no path it can measure. On a rail that should read a value, it can mean an open path: a missing or broken part, a lifted pad or a probe not touching the right spot. Check the probe first.
What does a reading near zero mean?
A diode or resistance reading near 0 on a rail that should read higher usually means the rail is shorted to ground, often by a failed capacitor or chip on that rail. Inject a low voltage, or use a thermal camera, to find the part that heats up.
Is this free, and is my board file uploaded?
Both the board pages and the Board Viewer are free. The viewer reads your boardview file in your own browser; the file is never uploaded.