Apple laptop board · OpenBoardData

820-4668 known-good readings

Known-good readings for the Apple laptop board 820-4668: 26 nets, including 8 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 8 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-4668.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 8 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 6

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V3_G3–3.300–
AI: what PP3V3_G3 is and how to check it

PP3V3_G3 is the 3.3 V always-on rail; the G3H stage comes from its name, meaning it should be present whenever the board has power. The only known-good figure here is 3.300 V; there is no known-good diode or resistance reading for this net. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A voltage far from 3.300 V usually points to a fault in the rail's source or a short on the rail, but that is a likely cause, not a confirmed one.

PP3V3_G3H_AVREF_SMC–3.280–
AI: what PP3V3_G3H_AVREF_SMC is and how to check it

PP3V3_G3H_AVREF_SMC — reference note

  • From its name, this is a 3.3 V always-on rail (G3H) feeding the SMC's AVREF reference input. The name is the only source for that; no board file is available to confirm which parts sit on it.
  • Known-good reading in the archive: 3.280 V. That is a community value and a guide only; no known-good diode or resistance reading exists for this net.
  • To check it: power off, then diode mode from the net to ground for a short-circuit check. Power on and measure the voltage, ideally at the SMC-side end of the rail.
  • A voltage far below 3.280 V points to a loaded or shorted rail, or a missing always-on supply upstream. A near-zero diode reading suggests a short; confirm before replacing anything.
PP3V42_G3H–3.400–
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, indicated by the "G3H" suffix in its name; it's the standby supply that should be present whenever the charger is connected. The archive lists one known-good reading for this rail: 3.400 V, with no condition noted. Check it unpowered in diode mode from the rail to ground for a short, then with power applied measure the voltage at the rail. No known-good diode reading exists here, so compare against a matching always-on rail or a known-good board. A voltage far below 3.400 V usually points to a problem upstream in the always-on supply or a heavy load on the rail, but that's a likely cause, not a confirmed one.

PP3V42_G3H_REG_R–3.400–
AI: what PP3V42_G3H_REG_R is and how to check it

PP3V42_G3H_REG_R is the always-on 3.42 V rail; the G3H in the name indicates it should be present whenever the board has power, before the main supplies come up. The only known-good figure here is 3.400 V, with no stated condition and no diode or resistance reading, so there is no known-good diode value on this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage well below 3.400 V points to a fault on the rail or its source, but a small difference can be normal, so compare with a matching net or a known-good board before condemning anything.

PP3V42_G3H_SMC_SPVSR–3.400–
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is the always-on 3.42 V rail feeding the SMC/SPVSR area; the "G3H" in the name indicates it should be present whenever the board has power.

  • Known-good voltage: 3.400 V (from the readings archive; a community guide, not a factory spec).
  • No known-good diode or resistance reading is recorded here.
  • Check it unpowered in diode mode from the rail to ground, then apply power and measure the voltage.

A voltage well below 3.4 V points to a load or short pulling the rail down, or a fault in whatever generates it; a diode reading far from a comparable rail on a known-good board suggests a shorted load.

PP12V_G3H–12.150–
AI: what PP12V_G3H is and how to check it

PP12V_G3H is a 12 V rail; the G3H suffix indicates it is always-on (from the name). The archive lists one known-good voltage for this rail: 12.150 V. No known-good diode or resistance reading is recorded here, so compare diode mode to ground against a matching net or a known-good board. Check it with the board unpowered in diode mode to ground, then power up and measure the voltage. A voltage far from 12.150 V points to a problem upstream on that rail rather than proof of a bad part; confirm with a second measurement before replacing anything.

S5 and SUS: standby 2

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP5V_S5–4.900–
AI: what PP5V_S5 is and how to check it

PP5V_S5 is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage. The only known-good reading here is 4.900 V, with no condition recorded, so treat it as a guide. Check it unpowered in diode mode from PP5V_S5 to ground, then power the board and measure the voltage. There is no known-good diode reading for this rail, so compare against a matching standby rail or a known-good board. A voltage far below 4.900 V usually points to the rail being loaded down or not being enabled, but that is a likely cause, not a confirmed one.

PP12V_S5–12.150–
AI: what PP12V_S5 is and how to check it
  • PP12V_S5 is a 12 V standby rail; the "S5" in its name marks it as a standby-stage supply (from the name).
  • Known-good reading in the archive: 12.150 V with power applied. No known-good diode or resistance reading here.
  • To check: with the board unpowered, measure diode mode from PP12V_S5 to ground; then power up and measure the voltage.
  • A voltage far from 12.150 V points to a problem in that standby supply or its load; without a known-good diode value, compare against a matching net or a known-good board before condemning anything.

Every net with a reading

NetDiodeVoltageResistance
BKLT_GATE0.00––
CPUVR_PH1_SNUB0.00––
CPUVR_PHASE1_K0.00––
FET_EN_P12V_S5–23.050–
P3V42G3H_BOOST–7.130–
P3V42G3H_FB–1.200–
P3V42G3H_SHDN_L–2.900–
P3V42G3H_SHDN_R_L–2.900–
P3V42G3H_SW–3.400–
PP3V3_G3–3.300–
PP3V3_G3H_AVREF_SMC–3.280–
PP3V42_G3H–3.400–
PP3V42_G3H_REG_R–3.400–
PP3V42_G3H_SMC_SPVSR–3.400–
PP5V_S5–4.900–
PP5VR3V3_SW_LCD_UF0.00––
PP12V_ACDC–12.150–
PP12V_G3H–12.150–
PP12V_S5–12.150–
PWR_BTN_R–3.400–
REG_BOOT_P5VS4–4.600–
REG_BOOT_P5VS4_RC–4.600–
REG_VIN_U7600–12.090–
SMC_MANUAL_RST_L–2.800–
SMC_PM_G2_EN–3.400–
SMC_RESET_L–3.300–

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP3V42_G3H read on the 820-4668?

OpenBoardData's known-good values for PP3V42_G3H on the 820-4668: voltage 3.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-4668?

OpenBoardData's known-good values for PP5V_S5 on the 820-4668: voltage 4.900. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_G3 read on the 820-4668?

OpenBoardData's known-good values for PP3V3_G3 on the 820-4668: voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-4668 board?

Open your own 820-4668 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License