Apple laptop board · OpenBoardData
820-3642 known-good readings
Known-good readings for the Apple laptop board 820-3642: 20 nets, including 1 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 1 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-3642.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 1 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
S0: running 1
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PPVOUT_S0_LCDBKLT | 1.0774 | – | – |
AI: what PPVOUT_S0_LCDBKLT is and how to check itPPVOUT_S0_LCDBKLT is the LCD backlight output rail; the "S0" in the name indicates it belongs to the running (S0) power state. The only known-good reading here is a diode value of 1.0774 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and the display connected. A diode reading far from 1.0774 usually points to a short or a faulty component on the backlight output, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
DP_INT_AUX_N | OL | – | – |
DP_INT_AUX_P | OL | – | – |
DP_INT_ML_N<0> | OL | – | – |
DP_INT_ML_N<1> | OL | – | – |
DP_INT_ML_N<2> | OL | – | – |
DP_INT_ML_N<3> | OL | – | – |
DP_INT_ML_P<0> | OL | – | – |
DP_INT_ML_P<1> | OL | – | – |
DP_INT_ML_P<2> | OL | – | – |
DP_INT_ML_P<3> | OL | – | – |
LCD_HPD_CONN | OL | – | – |
LED_RETURN_1 | 0.6291 | – | – |
LED_RETURN_2 | 0.6284 | – | – |
LED_RETURN_3 | 0.6290 | – | – |
LED_RETURN_4 | 0.6278 | – | – |
LED_RETURN_5 | 0.6294 | – | – |
LED_RETURN_6 | 0.6132 | – | – |
PP5VR3V3_SW_LCD | 0.6050 | – | – |
PPVOUT_S0_LCDBKLT | 1.0774 | – | – |
UNCONNECTED_243 | OL | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
How do I see these readings on my 820-3642 board?
Open your own 820-3642 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License