Apple desktop board · OpenBoardData
820-3588 known-good readings
Known-good readings for the Apple desktop board 820-3588: 1,569 nets, including 75 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 75 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-3588.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 75 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 10
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_G3H_SMC_VDDC | 0.513 | – | – |
AI: what PP1V2_G3H_SMC_VDDC is and how to check itPP1V2_G3H_SMC_VDDC is a 1.2 V rail feeding the SMC's VDDC supply; the G3H part of the name indicates it is an always-on rail (from the name). The archive lists a diode reading of 0.513 for this net, with no condition noted, so treat it as a guide. Check it with the board unpowered in diode mode from the net to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.513 usually points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault. | |||
PP3V3_G3 | 0.573 | – | – |
AI: what PP3V3_G3 is and how to check itPP3V3_G3 is a 3.3 V rail; the G3H suffix in its name marks it as an always-on rail, present whenever the board has power. The archive lists one known-good diode reading of 0.573 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode value far from 0.573 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything. | |||
PP3V3_G3H_AVREF_SMC | 0.609 | – | – |
AI: what PP3V3_G3H_AVREF_SMC is and how to check itPP3V3_G3H_AVREF_SMC is a 3.3 V always-on rail; the G3H part of the name indicates it is present whenever the charger is connected, and AVREF_SMC suggests it is a reference for the SMC. The archive lists one known-good diode reading of 0.609 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the net. A diode reading far from 0.609 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part, so compare with a matching always-on rail or a known-good board before replacing anything. | |||
PP3V3_G3H_BT_FET | 0.530 | – | – |
AI: what PP3V3_G3H_BT_FET is and how to check itPP3V3_G3H_BT_FET is an always-on 3.3 V rail, judged from its name: "G3H" means always on, and "BT_FET" suggests it feeds a Bluetooth-related FET switch. The archive lists one known-good diode reading of 0.530 to ground, with no condition recorded.
| |||
PP3V3_G3H_BT_FLT | 0.530 | – | – |
AI: what PP3V3_G3H_BT_FLT is and how to check itPP3V3_G3H_BT_FLT (820-3588) — reference note
| |||
PP3V3_G3H_SMC_VDDA | 0.321 | – | – |
AI: what PP3V3_G3H_SMC_VDDA is and how to check itPP3V3_G3H_SMC_VDDA is a 3.3 V always-on rail feeding the SMC's analog supply; the G3H part of the name indicates it should be present whenever the board has power, and the SMC_VDDA part marks it as the SMC analog supply (from the name). The archive lists one known-good reading: diode 0.321 to ground, with no condition given, so treat it as a guide. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then measure the voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.321 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault. | |||
PP3V42_G3H | 0.321 | – | – |
AI: what PP3V42_G3H is and how to check itPP3V42_G3H is the always-on 3.42 V rail, indicated by the G3H suffix in its name; it should be present whenever the board has power. The archive lists one known-good reading: diode 0.321 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode reading far from 0.321 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything. | |||
PP3V42_G3H_SMC_SPVSR | 0.378 | – | – |
AI: what PP3V42_G3H_SMC_SPVSR is and how to check itPP3V42_G3H_SMC_SPVSR is the always-on 3.42 V rail feeding the SMC side, judging by the G3H and SMC parts of its name (from the name, not from board data). The archive lists one known-good diode reading of 0.378 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.378 usually points to a short or a leaky part on the rail, while a much higher one can mean an open path; treat the single reading as a guide and compare with a matching net or a known-good board before condemning anything. | |||
PP12V_G3H | 0.567 | – | – |
AI: what PP12V_G3H is and how to check itPP12V_G3H is a 12 V rail that, judging by the G3H suffix in its name, is always-on whenever power is connected. The archive lists one known-good diode reading of 0.567 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is recorded here. A diode value far below 0.567 usually suggests a short or leaky load on the rail, while a much higher or open reading points to a broken path — but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
PPVBATT_G3_RTC | OL | – | – |
AI: what PPVBATT_G3_RTC is and how to check itPPVBATT_G3_RTC is the always-on G3H rail that keeps the RTC powered, based on its name. The only archived reading is a diode value of OL, with no condition recorded and no known-good voltage or resistance here. With the board unpowered, measure diode mode from the rail to ground and compare against that OL; then apply power and check the voltage on the rail. A diode reading far from OL usually points to a short or a leaky part on that net, but OL alone doesn't confirm the rail is healthy. | |||
S5 and SUS: standby 6
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S5 | 0.141 | – | – |
AI: what PP3V3_S5 is and how to check itPP3V3_S5 is the 3.3 V standby rail; the "S5" in its name marks it as a standby-stage supply. The only known-good reading here is a diode value of 0.141 to ground, with no condition noted; there is no known-good voltage reading for this rail in the data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.141 usually points to a short or a leaky load on the rail, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything. | |||
PP3V3_S5_XDP_R | 0.105 | – | – |
AI: what PP3V3_S5_XDP_R is and how to check itPP3V3_S5_XDP_R is a 3.3 V standby rail; the "S5" and "SUS" in its name mark it as a standby-stage supply, and the "XDP" suffix suggests it feeds a debug or connector-related load (that part is from the name, not confirmed by board data).
| |||
PP5V_S5 | 0.458 | – | – |
AI: what PP5V_S5 is and how to check itPP5V_S5 is a 5 V standby rail; the "S5" and "SUS" in its name indicate it belongs to the standby stage. The only known-good reading here is a diode value of 0.458 to ground, with no condition noted. Check it with the board unpowered in diode mode from PP5V_S5 to ground, then power up and measure the voltage on the rail. No known-good voltage reading is available for this rail. A diode reading far below 0.458 usually points to a short or leaky part on the rail, while a much higher or open reading suggests a broken connection; confirm with a voltage check before replacing anything. | |||
PP12V_S5 | 0.537 | – | – |
AI: what PP12V_S5 is and how to check itPP12V_S5 is a 12 V standby rail; the "S5" and "SUS" parts of the name indicate it belongs to the standby stage, and "12V" is its nominal voltage (all from the name). The archive lists one known-good reading: diode 0.537, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the DC voltage on the rail. No known-good voltage reading exists here, so compare against a matching rail elsewhere or a known-good board. A diode reading far from 0.537 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PPVOUT_S5_PCH_DCPSUSBYP | 0.383 | – | – |
AI: what PPVOUT_S5_PCH_DCPSUSBYP is and how to check it
| |||
PPVOUT_S5_PCH_DCPSUSBYP_R | 0.382 | – | – |
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it
| |||
S4 21
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S4_CAMERA | 0.327 | – | – |
AI: what PP1V2_S4_CAMERA is and how to check itPP1V2_S4_CAMERA is a 1.2 V rail in the S4 startup stage, judging by its name; it likely feeds camera circuitry, though that's general inference, not board data. The only known-good reading here is a diode value of 0.327 to ground, with no condition noted and no known-good voltage on record. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.327 usually points to a short or leaky part on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything. | |||
PP1V2_S4_CAMFILT | 0.342 | – | – |
AI: what PP1V2_S4_CAMFILT is and how to check itPP1V2_S4_CAMFILT is a 1.2 V rail in the S4 power state, judging from its name; the "CAMFILT" part suggests it feeds camera-related filtering, though that's from the name only. The archive lists one known-good diode reading of 0.342 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in S4. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode value far from 0.342 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a fault. | |||
PP1V2_S4_F_R | 0.327 | – | – |
AI: what PP1V2_S4_F_R is and how to check itPP1V2_S4_F_R is a 1.2 V rail; the "S4" in the name places it in the S4 startup stage, and the "_F_R" suffix suggests a filtered rail feeding the right side of a paired circuit. The only known-good reading here is a diode value of 0.327 to ground, with no condition recorded; no known-good voltage is listed for this rail. Check it with the board unpowered: meter in diode mode, black probe on ground, red on the rail, and compare with 0.327. Then power up and measure the DC voltage, expecting about 1.2 V from the name (general expectation, not a recorded value). A diode reading far below 0.327 usually points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection or missing component. | |||
PP1V8_S4_CAMERA | 0.438 | – | – |
AI: what PP1V8_S4_CAMERA is and how to check itPP1V8_S4_CAMERA is a 1.8 V rail for the camera section, in the S4 power state, judging by the name. The only known-good reading here is a diode of 0.438 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode, red probe on ground, black on the rail, then confirm the voltage with power applied. A diode reading far below 0.438 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault, so compare with a matching net or a known-good board before replacing anything. | |||
PP1V8_S4_CAMERA_F | 0.439 | – | – |
AI: what PP1V8_S4_CAMERA_F is and how to check itPP1V8_S4_CAMERA_F is a 1.8 V camera rail; the "S4" in the name indicates it belongs to the S4 startup stage (from the name, not confirmed by a schematic). The only known-good reading here is a diode value of 0.439 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is available for this rail. A diode reading far from 0.439 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part. | |||
PP3V3_S4 | 0.330 | – | – |
AI: what PP3V3_S4 is and how to check itPP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging by its name. The archive lists one known-good diode reading of 0.330 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.330 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part. | |||
PP3V3_S4_ALS_F | 0.330 | – | – |
AI: what PP3V3_S4_ALS_F is and how to check itPP3V3_S4_ALS_F is a 3.3 V rail that switches on at the S4 stage of power sequencing, judging by its name; the ALS suffix suggests it feeds the ambient light sensor circuit (general interpretation, not confirmed by board data). The only known-good reading here is a diode value of 0.330 to ground, taken with the board unpowered; no known-good voltage reading exists for this rail. Check it by measuring diode mode from the rail to ground with power off, then measure the voltage with the board powered and in S4 or later. A diode reading far from 0.330 usually points to a short or a leaky component on that rail, but confirm with a voltage measurement before replacing anything. | |||
PP3V3_S4_AP | 0.330 | – | – |
AI: what PP3V3_S4_AP is and how to check itPP3V3_S4_AP is a 3.3 V rail in the S4 startup stage, both from its name; it's a supply that comes up during S4 power sequencing. The only known-good reading here is a diode value of 0.330 to ground, with no condition given and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.330 suggests a short or a leaky load on the rail; a far higher or open reading suggests a broken path. Without voltage data, compare against a known-good board of the same model. | |||
PP3V3_S4_AP_FET | 0.502 | – | – |
AI: what PP3V3_S4_AP_FET is and how to check itPP3V3_S4_AP_FET is a 3.3 V rail in the S4 startup stage, both from its name; the FET suffix suggests it's switched through a transistor, though that's general reading, not from board data. The only known-good reading here is a diode value of 0.502 to ground, with no condition recorded. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage; no known-good voltage reading is listed here. A diode reading far below 0.502 suggests a short or leaky load on the rail, and a far higher one an open path, but a single reading doesn't confirm a bad part. | |||
PP3V3_S4_AP_FLT | 0.502 | – | – |
AI: what PP3V3_S4_AP_FLT is and how to check itPP3V3_S4_AP_FLT is a 3.3 V rail, judging from its name, and the S4 in the name puts it at the S4 startup stage. The only known-good reading here is a diode value of 0.502; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.502 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything. | |||
PP3V3_S4_CAMFILT | 0.330 | – | – |
AI: what PP3V3_S4_CAMFILT is and how to check itPP3V3_S4_CAMFILT is a 3.3 V rail in the S4 power stage, judging by its name (S4 is a later startup stage, and CAMFILT suggests it feeds camera filtering). The only known-good reading here is a diode value of 0.330 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.330 usually points to a short or a leaky part on that net, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything. | |||
PP5V_S4 | 0.156 | – | – |
AI: what PP5V_S4 is and how to check itPP5V_S4 is a 5 V rail in the S4 startup stage, both from its name. The only known-good reading here is a diode value of 0.156 to ground, with no condition recorded. Check it unpowered in diode mode from PP5V_S4 to ground, then measure the voltage with the board powered. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.156 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part. | |||
PP5V_S4_CAMERA_F | 0.160 | – | – |
AI: what PP5V_S4_CAMERA_F is and how to check itPP5V_S4_CAMERA_F is a 5 V rail for the camera circuit, enabled at the S4 power stage — both from the name. The only known-good reading here is diode mode to ground: 0.160, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below 0.160 usually points to a short or a leaky part on the rail, while a much higher one can mean an open trace or missing part. Treat it as a guide, not a confirmed fault, and trace the rail before replacing anything. | |||
PP5V_S4_EXTA_F | 0.540 | – | – |
AI: what PP5V_S4_EXTA_F is and how to check itPP5V_S4_EXTA_F is a 5 V rail that comes up at the S4 startup stage, both from its name; the "EXTA" part suggests it feeds external or accessory circuitry, but that's general reading, not from board data. The only known-good reading here is a diode value of 0.540 to ground, with no condition recorded. Check it with the board unpowered in diode mode, red probe on ground, then measure the voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.540 usually points to a short or a leaky part on that rail, but one reading doesn't confirm a fault. | |||
PP5V_S4_EXTA_ILIM | 0.540 | – | – |
AI: what PP5V_S4_EXTA_ILIM is and how to check itPP5V_S4_EXTA_ILIM is a 5 V rail in the S4 startup stage, judging from its name; the "ILIM" part suggests it sets a current limit for external circuitry, though that's general interpretation, not from board data. The only known-good reading here is a diode value of 0.540 to ground, with no condition noted and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied and compare against a matching rail or a known-good board. A diode reading far from 0.540 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault. | |||
PP5V_S4_EXTB_F | 0.538 | – | – |
AI: what PP5V_S4_EXTB_F is and how to check itPP5V_S4_EXTB_F is a 5 V rail that, from its name, belongs to the S4 startup stage and feeds an external-bus section of the board. The only known-good figure here is a diode reading of 0.538 to ground; there is no known-good voltage reading for it.
| |||
PP5V_S4_EXTB_ILIM | 0.538 | – | – |
AI: what PP5V_S4_EXTB_ILIM is and how to check itPP5V_S4_EXTB_ILIM is a 5 V rail that comes up at the S4 startup stage, judging by its name; the ILIM suffix suggests it feeds a current-limited external branch, though that part is general inference, not from the board data. The only known-good reading here is a diode value of 0.538 to ground, with no condition recorded. Check it with the board unpowered in diode mode, probe to ground, then confirm the voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.538 usually points to a short or leaky part on that rail; a far higher or open reading points to a broken connection. | |||
PP5V_S4_EXTC_F | 0.538 | – | – |
AI: what PP5V_S4_EXTC_F is and how to check itPP5V_S4_EXTC_F is a 5 V rail in the S4 startup stage, judging from its name; the board data doesn't say which parts sit on it. The only known-good reading here is a diode value of 0.538, with no condition given, and there is no known-good voltage reading in the data. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A diode reading far from 0.538 usually points to a short or a leaky load on the rail, but one reading isn't proof a part is bad. | |||
PP5V_S4_EXTC_ILIM | 0.538 | – | – |
AI: what PP5V_S4_EXTC_ILIM is and how to check itPP5V_S4_EXTC_ILIM is a 5 V rail in the S4 startup stage, judging by its name; the "ILIM" suffix suggests a current-limit reference or sense point, though that's general interpretation, not from this board's data. The only known-good reading here is a diode value of 0.538, with no condition recorded and no known-good voltage or resistance reading. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.538 usually points to a short or a damaged component on that net, but one reading isn't proof — confirm with a second measurement before replacing anything. | |||
PP5V_S4_EXTD_F | 0.536 | – | – |
AI: what PP5V_S4_EXTD_F is and how to check itPP5V_S4_EXTD_F is a 5 V rail that, from its name, belongs to the S4 startup stage and feeds an external display-related load. The only known-good reading here is a diode value of 0.536 to ground; no known-good voltage reading is recorded.
| |||
PP5V_S4_EXTD_ILIM | 0.536 | – | – |
AI: what PP5V_S4_EXTD_ILIM is and how to check itPP5V_S4_EXTD_ILIM is a 5 V rail that belongs to the S4 startup stage, judging from its name; the "ILIM" part suggests it feeds a current-limit reference. The archive lists one known-good diode reading of 0.536 to ground, with no condition recorded, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.536 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
S3: memory 7
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S3_VREFMRGN | 0.330 | – | – |
AI: what PP3V3_S3_VREFMRGN is and how to check itPP3V3_S3_VREFMRGN is a 3.3 V S3 (memory-stage) reference/margin rail, judged from the name; the board data doesn't list the parts on it. The only known-good reading here is diode 0.330 to ground, with no condition given, and there's no known-good voltage reading for this rail. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the same point. A diode reading far from 0.330 usually points to a short or a leaky part on that net, but a small difference can be normal, so confirm with a voltage check before replacing anything. | |||
PPVDDQ_S3 | 0.327 | – | – |
AI: what PPVDDQ_S3 is and how to check itPPVDDQ_S3 is a memory-stage rail (S3, from its name), likely the DDR VDDQ supply on this 820-3588. The archive lists one known-good diode reading of 0.327 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from PPVDDQ_S3 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.327 usually points to a short or a leaky part on that rail, but a single reading isn't proof of a bad part. | |||
PPVDDQ_S3_DDR | 0.327 | 1.300 | – |
AI: what PPVDDQ_S3_DDR is and how to check it
| |||
PPVREF_S3_MEM_VREFCA_A | 0.552 | – | – |
AI: what PPVREF_S3_MEM_VREFCA_A is and how to check it
| |||
PPVREF_S3_MEM_VREFCA_B | 0.553 | – | – |
AI: what PPVREF_S3_MEM_VREFCA_B is and how to check itPPVREF_S3_MEM_VREFCA_B — reference note
| |||
PPVREF_S3_MEM_VREFDQ_A | 0.553 | – | – |
AI: what PPVREF_S3_MEM_VREFDQ_A is and how to check itPPVREF_S3_MEM_VREFDQ_A is a memory reference voltage, active in the S3 state, judging by its name. The archive lists one known-good diode reading: 0.553, with no condition noted, so treat it as a guide only. With the board unpowered, measure diode mode from the net to ground and compare with 0.553; then apply power and check the voltage, though no known-good voltage reading exists here. A diode value far below 0.553 suggests a short or leaky part on the net, while far above it suggests an open path; either way, confirm with a second measurement before replacing anything. | |||
PPVREF_S3_MEM_VREFDQ_B | 0.559 | – | – |
AI: what PPVREF_S3_MEM_VREFDQ_B is and how to check itPPVREF_S3_MEM_VREFDQ_B is a memory reference voltage on the 820-3588, active in the S3 (memory) startup stage — both from the name. The archive's only known-good reading is a diode value of 0.559 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the net. A diode reading far from 0.559 usually points to a short or a damaged part on that net, but confirm with the voltage before replacing anything. | |||
S0: running 31
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V05_S0 | 0.079 | – | 79.100R |
AI: what PP1V05_S0 is and how to check itPP1V05_S0 is the 1.05 V rail that stays on in the S0 running state, judged from its name; the archive has no board file, so the parts it feeds aren't known. Known-good readings for this rail are a diode drop of 0.079 and 79.100R to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. A reading far from known-good usually points to a short or a failed load on the rail, but one reading alone doesn't confirm a bad part; there's no known-good voltage here, so compare against a matching rail or a known-good board. | |||
PP1V5_S0 | 0.362 | – | – |
AI: what PP1V5_S0 is and how to check itPP1V5_S0 is a 1.5 V rail; the S0 suffix in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.362 to ground, with no condition noted; no known-good voltage is recorded.
| |||
PP1V05_S0_PCH_VCC_CLK_F | 0.083 | – | – |
AI: what PP1V05_S0_PCH_VCC_CLK_F is and how to check it
| |||
PP1V05_S0_PCH_VCC_CLK_R | 0.083 | – | – |
AI: what PP1V05_S0_PCH_VCC_CLK_R is and how to check itPP1V05_S0_PCH_VCC_CLK_R is a 1.05 V rail; from the name it feeds the PCH clock section and is active in S0 (running). The archive lists one known-good diode reading of 0.083 to ground, with no condition noted and no voltage reading recorded.
| |||
PP3V3_S0 | 0.346 | – | – |
AI: what PP3V3_S0 is and how to check itPP3V3_S0 is the 3.3 V rail for the S0 (running) state, from its name; it should be present once the board is fully on. The archive has one known-good reading for this rail: diode 0.346 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from PP3V3_S0 to ground, then power the board and measure the voltage. A diode reading far from 0.346 usually points to a short or a leaky part on the rail, but a small difference can be normal, so compare with a matching rail or a known-good board before condemning anything. | |||
PP3V3_S0_BKLT_VDDIO_R | 0.345 | – | – |
AI: what PP3V3_S0_BKLT_VDDIO_R is and how to check it
| |||
PP3V3_S0_SSD | 0.462 | – | – |
AI: what PP3V3_S0_SSD is and how to check itPP3V3_S0_SSD is a 3.3 V rail that, from its name, is the SSD supply and is active in S0 (running). The archive lists one known-good diode reading of 0.462 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode value far from 0.462 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board. | |||
PP3V3_S0_SSD_FLT | 0.462 | – | – |
AI: what PP3V3_S0_SSD_FLT is and how to check itPP3V3_S0_SSD_FLT is a 3.3 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "SSD_FLT" suggests it feeds the SSD section. The archive lists a known-good diode reading of 0.462 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then confirm the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.462 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad component. | |||
PP3V3_S0_SW_SD_PWR | 0.559 | – | – |
AI: what PP3V3_S0_SW_SD_PWR is and how to check it
| |||
PP5V_S0 | 0.412 | – | – |
AI: what PP5V_S0 is and how to check itPP5V_S0 is the 5 V rail that is up in the S0 (running) state, as the name indicates. The only known-good reading in the archive is a diode value of 0.412 to ground, with no condition recorded; there is no known-good voltage reading here.
A diode reading far below 0.412 usually points to a short or a leaky part on the rail, while a much higher or open reading can mean a broken connection. Since no voltage value is recorded, compare against a known-good board of the same model. | |||
PP5V_S0_BKLT_R | 0.410 | – | – |
AI: what PP5V_S0_BKLT_R is and how to check itPP5V_S0_BKLT_R is a 5 V rail, and from its name it belongs to the S0 (running) state and feeds the backlight circuit. The archive lists one known-good diode reading of 0.410 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and confirm the voltage appears in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.410 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PP5V_S0_HDD | 0.591 | – | – |
AI: what PP5V_S0_HDD is and how to check itPP5V_S0_HDD is a 5 V rail that, from its name, is switched on in the S0 (running) state and feeds the drive (HDD) circuit. The archive lists one known-good diode reading of 0.591 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage in the S0 state. A diode reading far from 0.591 usually points to a short or a leaky part on that rail, but confirm with a voltage check and compare against a matching rail before replacing anything. | |||
PP12V_S0 | 0.464 | – | – |
AI: what PP12V_S0 is and how to check it
| |||
PP12V_S0_BKLT_FILT | 0.457 | – | – |
AI: what PP12V_S0_BKLT_FILT is and how to check it
| |||
PP12V_S0_BKLT_PWR | 0.168 | – | – |
AI: what PP12V_S0_BKLT_PWR is and how to check itPP12V_S0_BKLT_PWR is the backlight power rail, from its name: the S0 suffix means it's present in the running state. The only known-good reading here is a diode value of 0.168 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure its voltage with the board powered in the running state. No known-good voltage reading is available for this rail, so compare against a matching backlight rail on a known-good board. A diode reading far below 0.168 usually points to a short or leaky component on the rail; a far higher or open reading points to a broken feed or missing connection. | |||
PP12V_S0_BKLT_PWR_R | 0.167 | – | – |
AI: what PP12V_S0_BKLT_PWR_R is and how to check it
| |||
PP12V_S0_CPUVCC_FLT | 0.464 | – | – |
AI: what PP12V_S0_CPUVCC_FLT is and how to check it
| |||
PP12V_S0_FAN_0_FILT | 0.464 | – | – |
AI: what PP12V_S0_FAN_0_FILT is and how to check itPP12V_S0_FAN_0_FILT is a 12 V fan rail that is active in the S0 (running) state, judging from the name. The archive lists one known-good diode reading of 0.464 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far below 0.464 suggests a short or leaky load on the rail, while a much higher one can point to an open path; confirm with a voltage check before replacing anything. | |||
PPCPUVCC_S0_CPU | 0.011 | – | 10.900R |
AI: what PPCPUVCC_S0_CPU is and how to check it
| |||
PPCPUVCC_S0_SENSE_1 | 0.011 | – | 10.900R |
AI: what PPCPUVCC_S0_SENSE_1 is and how to check it
| |||
PPCPUVCC_S0_SENSE_2 | 0.011 | – | 10.900R |
AI: what PPCPUVCC_S0_SENSE_2 is and how to check it
| |||
PPCPUVCC_S0_SENSE_3 | 0.011 | – | 10.900R |
AI: what PPCPUVCC_S0_SENSE_3 is and how to check it
| |||
PPDDRVTT_S0 | 0.561 | – | – |
AI: what PPDDRVTT_S0 is and how to check it
| |||
PPHDD_S0 | 0.591 | – | – |
AI: what PPHDD_S0 is and how to check itPPHDD_S0 is a switched S0 (running-state) power rail for the HDD, inferred from its name; the archive has no schematic, so the parts on it aren't known. The only known-good reading is diode 0.591 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far below 0.591 suggests a short or leaky load on the rail; far above it suggests an open path. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. | |||
PPSSD_S0 | 0.462 | – | – |
AI: what PPSSD_S0 is and how to check itPPSSD_S0 is a power rail for the SSD supply, judged from its name; the "S0" suffix indicates it is active in the running (S0) state. The only known-good reading here is a diode value of 0.462 to ground, with no condition noted and no voltage reading recorded. Check it with the board unpowered in diode mode from PPSSD_S0 to ground, then power up and measure the voltage on the rail. A diode reading far below 0.462 usually suggests a short or a leaky load on the rail; a far higher or open reading points to a broken connection or missing supply. No known-good voltage is available for this rail, so compare against a matching rail or a known-good board. | |||
PPVCCIO_S0_CPU | 0.010 | – | 10.000R |
AI: what PPVCCIO_S0_CPU is and how to check it
| |||
PPVCOMP_S0_CPU | 0.020 | – | 20.000R |
AI: what PPVCOMP_S0_CPU is and how to check it
| |||
PPVDDQ_S0 | 0.162 | – | – |
AI: what PPVDDQ_S0 is and how to check itPPVDDQ_S0 is a DDR memory supply rail, judged from its name; the S0 suffix indicates it is active in the running state. The only archived reading is a diode value of 0.162 to ground, with no condition recorded. No known-good voltage reading exists here, so check the rail's voltage with power applied and compare it against what the memory spec expects rather than a stored figure. For the diode check, power the board off and measure from the rail to ground in diode mode. A reading far from 0.162 usually points to a short or a leaky component on that rail, but a single reading is only a guide, so confirm with the voltage measurement before replacing anything. | |||
PPVDDQ_S0_CPU | 0.162 | – | – |
AI: what PPVDDQ_S0_CPU is and how to check itPPVDDQ_S0_CPU is a CPU supply rail; the S0 in the name indicates it is active in the running state, and VDDQ usually means a memory I/O or DDR termination-style rail (general naming, not from this board's data). The archive lists one known-good reading: diode 0.162, with no condition recorded, and no known-good voltage or resistance here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.162, or a voltage that is missing or wrong once the board should be in S0, usually points to a short, an open feed, or the rail's regulator not coming up, but one reading alone doesn't confirm a bad part. | |||
PPVOUT_S0_PCH_DCPRTC | 0.716 | – | – |
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it
| |||
PPVOUT_S0_PCH_DCPSST | 0.470 | – | – |
AI: what PPVOUT_S0_PCH_DCPSST is and how to check itPPVOUT_S0_PCH_DCPSST is a power rail; the S0 in its name indicates it belongs to the running (S0) state, and the PCH/DCPSST naming suggests it feeds the chipset side of the board (that part is from the name, not from board data). The only known-good reading recorded is a diode reading of 0.470 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then confirm the voltage with power applied. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.470 usually points to a short or leaky load on the rail, while a much higher or open reading suggests a broken connection; treat that as a guide, not a confirmed fault. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
4V5_NR | 0.657 | – | – |
4V5_REG_EN | 0.346 | – | – |
4V5_REG_IN | 0.412 | – | – |
ACDC_BURST | 0.601 | – | – |
ACDC_BURST_EN_L | 0.749 | – | – |
AGND_CPU | 0.000 | – | – |
AGND_P1V05S0 | 0.000 | – | – |
AGND_VDDQS3 | 0.000 | – | – |
ALL_SYS_PWRGD | 0.502 | – | – |
AP_CLKREQ_L | 0.442 | – | – |
AP_CLKREQ_Q_L | 0.460 | – | – |
AP_EVENT_L | 0.750 | – | – |
AP_PWR_EN | 0.438 | – | – |
AP_RESET_CONN_L | 0.461 | – | – |
AP_RESET_L | 0.422 | – | – |
AP_WAKE_L | 1.790 | – | – |
AUD_CODEC_MICBIAS | 0.567 | – | – |
AUD_DMIC_CLK | 0.730 | – | – |
AUD_DMIC_CLK_CONN | 0.733 | – | – |
AUD_DMIC_SDA1 | 0.710 | – | – |
AUD_DMIC_SDA1_CONN | 0.711 | – | – |
AUD_GPIO_2 | 0.610 | – | – |
AUD_GPIO_3 | 0.569 | – | – |
AUD_HP_PORT_REF | OL | – | – |
AUD_HS_MIC_N | OL | – | – |
AUD_HS_MIC_P | 1.544 | – | – |
AUD_HS_MIC_RC_N | OL | – | – |
AUD_HS_MIC_RC_P | OL | – | – |
AUD_I2C_INT_L | 0.525 | – | – |
AUD_IP_PERIPHERAL_DET | 0.574 | – | – |
AUD_IP_PERPH_DET_DB | 0.575 | – | – |
AUD_IP_PERPH_DET_R | OL | – | – |
AUD_IPHS_SWITCH_EN | 0.504 | – | – |
AUD_IPHS_SWITCH_EN_PCH | 0.514 | – | – |
AUD_J1_DET_RC | OL | – | – |
AUD_J1_GND_ANALOG | 0.000 | – | – |
AUD_J1_HP_OUTL | OL | – | – |
AUD_J1_HP_OUTR | 1.325 | – | – |
AUD_J1_HP_PORT_REF | OL | – | – |
AUD_J1_MIC_BIAS | 0.554 | – | – |
AUD_J1_MIC_N | OL | – | – |
AUD_J1_MIC_P | 1.544 | – | – |
AUD_J1_PP3V3_S0 | 0.330 | – | – |
AUD_J1_TIPDET1_R | OL | – | – |
AUD_J1_TIPDET2_R | OL | – | – |
AUD_J1_TYPEDET_R | OL | – | – |
AUD_LAMP_AVDD | 0.525 | – | – |
AUD_LAMP_BOOTLN | 0.581 | – | – |
AUD_LAMP_BOOTLP | 0.584 | – | – |
AUD_LAMP_BOOTRN | 0.582 | – | – |
AUD_LAMP_BOOTRP | 0.584 | – | – |
AUD_LAMP_EDGE | 0.525 | – | – |
AUD_LAMP_GAIN | 0.610 | – | – |
AUD_LAMP_LIN_N | 0.615 | – | – |
AUD_LAMP_LIN_P | 0.613 | – | – |
AUD_LAMP_LINC_N | 0.721 | – | – |
AUD_LAMP_LINC_P | 0.714 | – | – |
AUD_LAMP_MONO | 0.000 | – | – |
AUD_LAMP_OUTNL | 0.557 | – | – |
AUD_LAMP_OUTNR | 0.556 | – | – |
AUD_LAMP_OUTPL | 0.557 | – | – |
AUD_LAMP_OUTPR | 0.557 | – | – |
AUD_LAMP_RIN_N | 0.613 | – | – |
AUD_LAMP_RIN_P | 0.614 | – | – |
AUD_LAMP_RINC_N | 0.719 | – | – |
AUD_LAMP_RINC_P | 0.713 | – | – |
AUD_LI_COM | 0.735 | – | – |
AUD_LI_P_L | 0.740 | – | – |
AUD_LI_P_R | 0.741 | – | – |
AUD_LI_TIPDET | 0.385 | – | – |
AUD_LO1_L_C_N | OL | – | – |
AUD_LO1_L_C_P | OL | – | – |
AUD_LO1_L_N | 0.713 | – | – |
AUD_LO1_L_P | 0.719 | – | – |
AUD_LO1_R_C_N | OL | – | – |
AUD_LO1_R_C_P | OL | – | – |
AUD_LO1_R_N | 0.713 | – | – |
AUD_LO1_R_P | 0.717 | – | – |
AUD_LO2_L_N | 0.714 | – | – |
AUD_LO2_L_P | 0.721 | – | – |
AUD_LO2_R_N | 0.717 | – | – |
AUD_LO2_R_P | 0.718 | – | – |
AUD_MIC_INL_N | 0.740 | – | – |
AUD_MIC_INL_P | 0.739 | – | – |
AUD_MIC_INN_R | 0.740 | – | – |
AUD_MIC_INP_R | 0.740 | – | – |
AUD_OUTJACK_INSERT | 0.621 | – | – |
AUD_OUTJACK_INSERT_L | 0.623 | – | – |
AUD_PORTA_DET_L | 0.614 | – | – |
AUD_PORTB_DET_L | 1.183 | – | – |
AUD_PORTC_DET_L | 0.620 | – | – |
AUD_PORTD_DET_L | 1.106 | – | – |
AUD_RAMP_AVDD | 0.528 | – | – |
AUD_RAMP_BOOTLN | 0.584 | – | – |
AUD_RAMP_BOOTLP | 0.586 | – | – |
AUD_RAMP_BOOTRN | 0.584 | – | – |
AUD_RAMP_BOOTRP | 0.586 | – | – |
AUD_RAMP_EDGE | 0.528 | – | – |
AUD_RAMP_GAIN | 0.612 | – | – |
AUD_RAMP_LIN_N | 0.618 | – | – |
AUD_RAMP_LIN_P | 0.618 | – | – |
AUD_RAMP_LINC_N | 0.713 | – | – |
AUD_RAMP_LINC_P | 0.717 | – | – |
AUD_RAMP_MONO | 0.000 | – | – |
AUD_RAMP_OUTNL | 0.558 | – | – |
AUD_RAMP_OUTNR | 0.558 | – | – |
AUD_RAMP_OUTPL | 0.558 | – | – |
AUD_RAMP_OUTPR | 0.558 | – | – |
AUD_RAMP_RIN_N | 0.614 | – | – |
AUD_RAMP_RIN_P | 0.615 | – | – |
AUD_RAMP_RINC_N | 0.718 | – | – |
AUD_RAMP_RINC_P | 0.717 | – | – |
AUD_SDI_R | 0.443 | – | – |
AUD_SENSE_A | 0.754 | – | – |
AUD_SPDIF_CHIP | 0.708 | – | – |
AUD_SPDIF_OUT | 0.729 | – | – |
AUD_SPKR_LTWT_OUT_N | 0.557 | – | – |
AUD_SPKR_LTWT_OUT_P | 0.557 | – | – |
AUD_SPKR_LWFR_OUT_N | 0.558 | – | – |
AUD_SPKR_LWFR_OUT_P | 0.557 | – | – |
AUD_SPKR_RTWT_OUT_N | 0.556 | – | – |
AUD_SPKR_RTWT_OUT_P | 0.557 | – | – |
AUD_SPKR_RWFR_OUT_N | 0.558 | – | – |
AUD_SPKR_RWFR_OUT_P | 0.558 | – | – |
AUD_SPKR_VENDOR_ID_L | OL | – | – |
AUD_SPKR_VENDOR_ID_R | OL | – | – |
AUD_SPKRAMP_MAC_SHDN_L | 0.563 | – | – |
AUD_SPKRAMP_WIN_SHDN_L | 0.570 | – | – |
AUD_TIPDET_INV | OL | – | – |
AUD_TIPDET1_R | OL | – | – |
AUD_TIPDET2_R | OL | – | – |
AUD_TYPEDET_OD | OL | – | – |
AUD_TYPEDET_OD_INV | 0.459 | – | – |
AUD_TYPEDET_R | OL | – | – |
BKLT_BOOST | 0.412 | – | – |
BKLT_BOOST_1 | 0.412 | – | – |
BKLT_BOOST_2 | 0.412 | – | – |
BKLT_EN | 0.560 | – | – |
BKLT_EN_DIV | 0.719 | – | – |
BKLT_EN_L | OL | – | – |
BKLT_FB | 0.704 | – | – |
BKLT_FB_R | 0.410 | – | – |
BKLT_FB_XW | 0.410 | – | – |
BKLT_FLT | 0.564 | – | – |
BKLT_FLT_RC | OL | – | – |
BKLT_GATE | 0.488 | – | – |
BKLT_GATE_R | 0.488 | – | – |
BKLT_ISEN1 | 0.655 | – | – |
BKLT_ISEN1_R | 1.164 | – | – |
BKLT_ISEN2 | 0.655 | – | – |
BKLT_ISEN2_R | 1.164 | – | – |
BKLT_ISEN3 | 0.656 | – | – |
BKLT_ISEN3_R | 1.151 | – | – |
BKLT_ISEN4 | 0.653 | – | – |
BKLT_ISEN4_R | 1.146 | – | – |
BKLT_ISEN5 | 0.653 | – | – |
BKLT_ISEN5_R | 1.132 | – | – |
BKLT_ISEN6 | 0.654 | – | – |
BKLT_ISEN6_R | 1.123 | – | – |
BKLT_ISET | 0.562 | – | – |
BKLT_PHASE | 0.167 | – | – |
BKLT_SCL | 0.488 | – | – |
BKLT_SDA | 0.502 | – | – |
BKLT_SHUTDOWN | 0.726 | – | – |
BKLT_SNUBBER | OL | – | – |
BKLT_SW_N | 0.000 | – | – |
BKLT_SW_P | 0.000 | – | – |
BKLT_SW_R | 0.000 | – | – |
BKLT_VSYNC | 0.566 | – | – |
BKLT_VSYNC_R | 0.566 | – | – |
BT_PWR_EN | 0.459 | – | – |
BT_PWR_RST | OL | – | – |
BT_PWR_RST_L | 0.691 | – | – |
BT_RESET_MASK_L | 0.449 | – | – |
BURSTMODE_EN | OL | – | – |
BURSTMODE_EN_L | 1.030 | – | – |
BURSTMODE_EN_R_L | 1.995 | – | – |
CAM_AGND | 0.000 | – | – |
CAM_EXT_BOOT | 0.535 | – | – |
CAM_EXT_BOOT_L | 0.686 | – | – |
CAM_P1V2_RST_HOLDOFF | 1.337 | – | – |
CAM_P1V2_RST_HOLDOFF_L | 1.224 | – | – |
CAM_PLLGND | 0.000 | – | – |
CAM_PROC_RESET_L | 0.533 | – | – |
CAM_RX | 0.537 | – | – |
CAM_SF_CLK | 0.501 | – | – |
CAM_SF_CLK_R | 0.538 | – | – |
CAM_SF_CS_L | 0.544 | – | – |
CAM_SF_DIN | 0.524 | – | – |
CAM_SF_DIN_R | 0.538 | – | – |
CAM_SF_DOUT | 0.526 | – | – |
CAM_SF_DOUT_R | 0.545 | – | – |
CAM_SF_HOLD_L | 0.728 | – | – |
CAM_SF_WP_L | 0.544 | – | – |
CAM_TEST | 0.049 | – | 47.200R |
CAM_TX | 0.542 | – | – |
CAM_USB_VRES | 0.819 | – | – |
CAM_XTAL_IN | 0.492 | – | – |
CAM_XTAL_OUT | 0.560 | – | – |
CAM_XTAL_OUT_R | 0.607 | – | – |
CORE_VOLTAGES_ON | 0.593 | – | – |
CORE_VOLTAGES_ON_R | 1.333 | – | – |
CPU_CATERR_L | 0.219 | – | – |
CPU_CFG_RCOMP | 0.052 | – | 51.500R |
CPU_CFG<1> | 0.227 | – | – |
CPU_CFG<2> | 0.224 | – | – |
CPU_CFG<3> | 0.225 | – | – |
CPU_CFG<4> | 0.222 | – | – |
CPU_CFG<9> | 0.221 | – | – |
CPU_CFG<10> | 0.225 | – | – |
CPU_CFG<16> | 0.227 | – | – |
CPU_CFG<17> | 0.226 | – | – |
CPU_CFG<19> | 0.227 | – | – |
CPU_CLK135M_DPLLREF_N | 0.280 | – | – |
CPU_CLK135M_DPLLSS_P | 0.281 | – | – |
CPU_DC_A51 | OL | – | – |
CPU_DC_BC1 | OL | – | – |
CPU_DC_BC54 | OL | – | – |
CPU_DC_BF4 | OL | – | – |
CPU_DC_BF51 | OL | – | – |
CPU_DC_D1 | OL | – | – |
CPU_DC_D54 | OL | – | – |
CPU_DIMM_VREFCA | 0.712 | – | – |
CPU_DIMMB_VREFDQ | 0.752 | – | – |
CPU_EDP_RCOMP | 0.045 | – | 44.200R |
CPU_MEM_RESET_L | 0.306 | – | – |
CPU_MEM_VREFCA_A_ISOL | 0.554 | – | – |
CPU_MEM_VREFCA_B_ISOL | 0.553 | – | – |
CPU_MEM_VREFDQ_A_ISOL | 0.555 | – | – |
CPU_MEM_VREFDQ_B_ISOL | 0.560 | – | – |
CPU_PECI | 0.376 | – | – |
CPU_PECI_R | 0.331 | – | – |
CPU_PEG_RCOMP | 0.045 | – | 44.000R |
CPU_PROCHOT_L | 0.073 | – | 72.800R |
CPU_PROCHOT_R_L | 0.119 | – | – |
CPU_PWR_DEBUG | 0.227 | – | – |
CPU_PWRGD | 0.380 | – | – |
CPU_RESET_L | 0.390 | – | – |
CPU_SKTOCC | 0.716 | – | – |
CPU_SKTOCC_L_ALIAS | OL | – | – |
CPU_SM_RCOMP<0> | 0.101 | – | – |
CPU_SM_RCOMP<1> | 0.076 | – | 75.200R |
CPU_SM_RCOMP<2> | 0.101 | – | – |
CPU_TESTLO_F20 | 0.052 | – | 51.300R |
CPU_TESTLO_F21 | 0.051 | – | – |
CPU_TT_OC_L | OL | – | – |
CPU_VCCSENSE_N | 0.002 | – | 1.600R |
CPU_VCCSENSE_P | 0.011 | – | 11.300R |
CPU_VCCSENSE_R_N | 0.000 | – | – |
CPU_VCCSENSE_R_P | 0.012 | – | – |
CPU_VIDALERT_L | 0.085 | – | 85.000R |
CPU_VIDALERT_R_L | 0.128 | – | – |
CPU_VIDSCLK | 0.064 | – | 64.000R |
CPU_VIDSCLK_R | 0.064 | – | 64.500R |
CPU_VIDSOUT | 0.065 | – | 64.600R |
CPU_VIDSOUT_R | 0.065 | – | – |
CPUVCC_COMP_RC | OL | – | – |
CPUVCC_DVC_RC | 2.300 | – | – |
CPUVCC_FB_R_1 | OL | – | – |
CPUVCC_FB_R_2 | 0.035 | – | 33.800R |
CPUVCC_FB_RC | 0.286 | – | – |
CPUVCC_FB_RC_2 | OL | – | – |
CPUVCC_IMON_R | 1.004 | – | – |
CPUVCC_PSICOMP_RC | 1.377 | – | – |
CS4206_DMIC_SCL | 0.708 | – | – |
CS4206_FLYC | 0.437 | – | – |
CS4206_FLYN | 1.205 | – | – |
CS4206_FLYP | 0.629 | – | – |
CS4206_FN | 0.100 | – | – |
CS4206_FP | 0.459 | – | – |
CS4206_HPREF | 0.000 | – | – |
CS4206_VCOM | 0.620 | – | – |
DEBUG_RESET_L | 0.587 | – | – |
DGND_BKLT | 0.000 | – | – |
DMI_CLK100M_CPU_N | 0.284 | – | – |
DMI_N2S_N<0> | 0.251 | – | – |
DMI_N2S_N<3> | 0.250 | – | – |
DMI_S2N_N<0> | 0.258 | – | – |
DP_A_AUXCH_DDC_N | 0.701 | – | – |
DP_A_AUXCH_DDC_P | 0.692 | – | – |
DP_A_LSX_ML_N<1> | 0.712 | – | – |
DP_A_LSX_ML_P<1> | 0.722 | – | – |
DP_AUXIO_EN | 0.505 | – | – |
DP_B_AUXCH_DDC_N | 0.702 | – | – |
DP_B_AUXCH_DDC_P | 0.689 | – | – |
DP_B_LSX_ML_N<1> | 0.711 | – | – |
DP_B_LSX_ML_P<1> | 0.723 | – | – |
DP_IG_A_HPD_L | 0.410 | – | – |
DP_INT_AUX_C_N | 0.733 | – | – |
DP_INT_AUX_C_P | 0.344 | – | – |
DP_INT_AUX_N | 0.379 | – | – |
DP_INT_AUX_P | 0.380 | – | – |
DP_INT_DDC_CLK | 0.649 | – | – |
DP_INT_DDC_DATA | 0.642 | – | – |
DP_INT_HPD | 0.630 | – | – |
DP_INT_SPDIF_AUDIO | 0.767 | – | – |
DP_INTPNL_AUX_N | 0.731 | – | – |
DP_INTPNL_AUX_P | 0.728 | – | – |
DP_INTPNL_ML_C_N<0> | 0.458 | – | – |
DP_INTPNL_ML_C_N<1> | 0.457 | – | – |
DP_INTPNL_ML_C_P<0> | 0.457 | – | – |
DP_INTPNL_ML_C_P<1> | 0.457 | – | – |
DP_INTPNL_ML_N<0> | OL | – | – |
DP_INTPNL_ML_N<1> | OL | – | – |
DP_INTPNL_ML_P<0> | OL | – | – |
DP_INTPNL_ML_P<1> | OL | – | – |
DP_TBT_SEL | 0.385 | – | – |
DP_TBTPA_AUXCH_C_N | 0.576 | – | – |
DP_TBTPA_AUXCH_C_P | 0.623 | – | – |
DP_TBTPA_AUXCH_N | 0.736 | – | – |
DP_TBTPA_AUXCH_P | 0.730 | – | – |
DP_TBTPA_DDC_CLK | 0.554 | – | – |
DP_TBTPA_HPD | 0.570 | – | – |
DP_TBTPA_ML_C_N<1> | 0.318 | – | – |
DP_TBTPA_ML_C_N<3> | 0.164 | – | – |
DP_TBTPA_ML_C_P<1> | 0.319 | – | – |
DP_TBTPA_ML_C_P<3> | 0.315 | – | – |
DP_TBTPA_ML_N<1> | 0.683 | – | – |
DP_TBTPA_ML_N<3> | OL | – | – |
DP_TBTPA_ML_P<1> | 0.696 | – | – |
DP_TBTPA_ML_P<3> | OL | – | – |
DP_TBTPB_AUXCH_C_N | 0.564 | – | – |
DP_TBTPB_AUXCH_C_P | 0.606 | – | – |
DP_TBTPB_AUXCH_N | 0.739 | – | – |
DP_TBTPB_AUXCH_P | 0.728 | – | – |
DP_TBTPB_DDC_CLK | 0.555 | – | – |
DP_TBTPB_DDC_DATA | 0.557 | – | – |
DP_TBTPB_HPD | 0.569 | – | – |
DP_TBTPB_ML_C_N<1> | 0.318 | – | – |
DP_TBTPB_ML_C_N<3> | 0.320 | – | – |
DP_TBTPB_ML_C_P<1> | 0.318 | – | – |
DP_TBTPB_ML_C_P<3> | 0.277 | – | – |
DP_TBTPB_ML_N<1> | 0.683 | – | – |
DP_TBTPB_ML_N<3> | OL | – | – |
DP_TBTPB_ML_P<1> | OL | – | – |
DP_TBTPB_ML_P<3> | OL | – | – |
DP_TBTSNK0_AUXCH_C_N | 0.380 | – | – |
DP_TBTSNK0_AUXCH_C_P | 0.380 | – | – |
DP_TBTSNK0_AUXCH_N | 0.572 | – | – |
DP_TBTSNK0_AUXCH_P | 0.629 | – | – |
DP_TBTSNK0_DDC_CLK | 0.568 | – | – |
DP_TBTSNK0_DDC_DATA | 0.570 | – | – |
DP_TBTSNK0_HPD | 0.561 | – | – |
DP_TBTSNK0_ML_C_N<0> | 0.258 | – | – |
DP_TBTSNK0_ML_C_N<1> | 0.258 | – | – |
DP_TBTSNK0_ML_C_N<2> | 0.259 | – | – |
DP_TBTSNK0_ML_C_N<3> | 0.260 | – | – |
DP_TBTSNK0_ML_C_P<0> | 0.259 | – | – |
DP_TBTSNK0_ML_C_P<1> | 0.258 | – | – |
DP_TBTSNK0_ML_C_P<2> | 0.260 | – | – |
DP_TBTSNK0_ML_C_P<3> | 0.262 | – | – |
DP_TBTSNK0_ML_N<0> | 0.581 | – | – |
DP_TBTSNK0_ML_N<1> | 0.581 | – | – |
DP_TBTSNK0_ML_N<2> | 0.581 | – | – |
DP_TBTSNK0_ML_N<3> | 0.581 | – | – |
DP_TBTSNK0_ML_P<0> | 0.581 | – | – |
DP_TBTSNK0_ML_P<1> | 0.581 | – | – |
DP_TBTSNK0_ML_P<2> | 0.581 | – | – |
DP_TBTSNK0_ML_P<3> | 0.581 | – | – |
DP_TBTSNK1_AUXCH_C_N | 0.383 | – | – |
DP_TBTSNK1_AUXCH_C_P | 0.384 | – | – |
DP_TBTSNK1_AUXCH_N | 0.576 | – | – |
DP_TBTSNK1_AUXCH_P | 0.642 | – | – |
DP_TBTSNK1_HPD | 0.567 | – | – |
DP_TBTSNK1_ML_C_N<0> | 0.260 | – | – |
DP_TBTSNK1_ML_C_N<1> | 0.262 | – | – |
DP_TBTSNK1_ML_C_N<2> | 0.260 | – | – |
DP_TBTSNK1_ML_C_N<3> | 0.262 | – | – |
DP_TBTSNK1_ML_C_P<0> | 0.260 | – | – |
DP_TBTSNK1_ML_C_P<1> | 0.261 | – | – |
DP_TBTSNK1_ML_C_P<2> | 0.261 | – | – |
DP_TBTSNK1_ML_C_P<3> | 0.258 | – | – |
DP_TBTSNK1_ML_N<0> | 0.581 | – | – |
DP_TBTSNK1_ML_N<1> | 0.581 | – | – |
DP_TBTSNK1_ML_N<2> | 0.582 | – | – |
DP_TBTSNK1_ML_N<3> | 0.580 | – | – |
DP_TBTSNK1_ML_P<0> | 0.581 | – | – |
DP_TBTSNK1_ML_P<1> | 0.581 | – | – |
DP_TBTSNK1_ML_P<2> | 0.581 | – | – |
DP_TBTSNK1_ML_P<3> | 0.582 | – | – |
DP_TBTSRC_AUX_C_N | 0.735 | – | – |
DP_TBTSRC_AUX_C_P | 0.712 | – | – |
DP_TBTSRC_AUXCH_N | 0.567 | – | – |
DP_TBTSRC_AUXCH_P | 0.636 | – | – |
DP_TBTSRC_HPD | 0.569 | – | – |
DP_TBTSRC_ML_C_N<0> | 0.449 | – | – |
DP_TBTSRC_ML_C_N<1> | 0.499 | – | – |
DP_TBTSRC_ML_C_P<0> | 0.498 | – | – |
DP_TBTSRC_ML_C_P<1> | 0.497 | – | – |
DP_TBTSRC_ML_N<0> | 0.319 | – | – |
DP_TBTSRC_ML_N<1> | 0.319 | – | – |
DP_TBTSRC_ML_P<0> | 0.316 | – | – |
DP_TBTSRC_ML_P<1> | 0.319 | – | – |
DPMUX_UC_IRQ | 0.624 | – | – |
ENET_ACT | OL | – | – |
ENET_ASF_GPIO | 0.749 | – | – |
ENET_CLKREQ_L | 0.514 | – | – |
ENET_CR_DATA<0> | 0.514 | – | – |
ENET_CR_DATA<1> | 0.515 | – | – |
ENET_CR_DATA<2> | 0.516 | – | – |
ENET_CR_DATA<3> | 0.535 | – | – |
ENET_CR_DATA<4> | 0.668 | – | – |
ENET_CR_DATA<5> | 0.663 | – | – |
ENET_CR_DATA<6> | 0.668 | – | – |
ENET_CR_DATA<7> | 0.668 | – | – |
ENET_CR_PWREN | 0.529 | – | – |
ENET_CS_L | 0.693 | – | – |
ENET_LOW_PWR | 0.458 | – | – |
ENET_LOW_PWR_PCH | 0.620 | – | – |
ENET_MEDIA_SENSE | 0.415 | – | – |
ENET_MISO | 0.592 | – | – |
ENET_MOSI | 0.627 | – | – |
ENET_RDAC | 0.577 | – | – |
ENET_RESET_L | 0.457 | – | – |
ENET_SCLK | 0.631 | – | – |
ENET_SD_CLK | 0.514 | – | – |
ENET_SD_CMD | 0.516 | – | – |
ENET_SD_DETECT_L | 0.461 | – | – |
ENET_SD_RESET_L | 0.423 | – | – |
ENET_SR_DISABLE | 0.556 | – | – |
ENET_SR_LX | 0.283 | – | – |
ENET_TRAFFICLED_L | 0.662 | – | – |
ENET_VMAIN_PRSNT | 0.596 | – | – |
ENET_WAKE_L | 0.575 | – | – |
ENET_XTALVDDH | 0.360 | – | – |
ENETCONN_MCT_BS | OL | – | – |
ENETCONN_MCT0 | OL | – | – |
ENETCONN_MCT1 | OL | – | – |
ENETCONN_MCT2 | OL | – | – |
ENETCONN_MCT3 | OL | – | – |
ENETCONN_MDI_N<0> | 0.360 | – | – |
ENETCONN_MDI_N<1> | 0.361 | – | – |
ENETCONN_MDI_N<3> | 0.361 | – | – |
ENETCONN_MDI_P<1> | 0.361 | – | – |
ENETCONN_MDI_P<2> | 0.361 | – | – |
ENETCONN_MDI_P<3> | 0.361 | – | – |
ENETCONN_MDI_T_N<0> | OL | – | – |
ENETCONN_MDI_T_N<1> | OL | – | – |
ENETCONN_MDI_T_N<2> | OL | – | – |
ENETCONN_MDI_T_N<3> | OL | – | – |
ENETCONN_MDI_T_P<0> | OL | – | – |
ENETCONN_MDI_T_P<1> | OL | – | – |
ENETCONN_MDI_T_P<2> | OL | – | – |
ENETCONN_MDI_T_P<3> | OL | – | – |
ENETCONN_TCT | 0.361 | – | – |
FAN_0_PWM_FET | 1.212 | – | – |
FAN_0_PWM_FILT | 1.212 | – | – |
FAN_0_TACH_FET | OL | – | – |
FAN_0_TACH_FILT | OL | – | – |
FDI_CSYNC | 0.357 | – | – |
FDI_INT | 0.356 | – | – |
FET_EN_P12V_S5 | 0.681 | – | – |
FET_EN_P12V_S5_R | OL | – | – |
FET_RAMP_P3V3_S0 | 0.732 | – | – |
FET_RAMP_P3V3_S4 | 0.732 | – | – |
FW_PME_L | 0.694 | – | – |
G3_POWERON_L | 0.754 | – | – |
GND | 0.000 | – | – |
GND_AUDIO_CODEC | 0.000 | – | – |
GPU_GOOD | 0.462 | – | – |
GPU_PRESENT_DRAIN | 0.592 | – | – |
GPU_PRESENT_R | 1.356 | – | – |
HDA_BIT_CLK | 0.466 | – | – |
HDA_BIT_CLK_R | 0.431 | – | – |
HDA_RST_L | 0.463 | – | – |
HDA_RST_R_L | 0.426 | – | – |
HDA_SDIN0 | 0.421 | – | – |
HDA_SDOUT | 0.466 | – | – |
HDA_SDOUT_R | 0.426 | – | – |
HDA_SYNC | 0.466 | – | – |
HDA_SYNC_R | 0.432 | – | – |
HDD_OOB_1V00_REF | 0.702 | – | – |
HDD_OOB1_D2R_F_L | 0.635 | – | – |
HDD_OOB1_D2R_L | 0.637 | – | – |
HDD_OOB1_D2R_R_L | 0.703 | – | – |
HDD_PWR_EN | 0.529 | – | – |
HS_HDET | 1.971 | – | – |
HS_MIC_BIAS | 0.554 | – | – |
HS_RX_BP | 0.572 | – | – |
HS_SW_DET | 0.547 | – | – |
I2C_CAMSENSOR_SCL | 0.535 | – | – |
I2C_CAMSENSOR_SDA | 0.535 | – | – |
I2C_TBTRTR_SCL | 0.679 | – | – |
I2C_TBTRTR_SDA | 0.681 | – | – |
ICT_JTAG_EN | 1.006 | – | – |
ISNS_CPUVCC | 0.747 | – | – |
ISNS_CPUVCC_FB | 0.681 | – | – |
ISNS_CPUVCC_FB_R | 0.662 | – | – |
ISNS_HDDS0 | 0.000 | – | – |
ISNS_HDDS0_R | OL | – | – |
ISNS_P3V3S4_AP | OL | – | – |
ISNS_P3V3S4_AP_R | OL | – | – |
ISNS_P12VG3H | 0.744 | – | – |
ISNS_P12VG3H_R | 0.709 | – | – |
ISNS_PVDDQS0 | 0.745 | – | – |
ISNS_PVDDQS0_R | 0.710 | – | – |
ISNS_SSDS0 | 0.746 | – | – |
ISNS_SSDS0_R | 0.669 | – | – |
ISNS_VDDQS3_DDR | 0.746 | – | – |
ISNS_VDDQS3_DDR_R | 0.709 | – | – |
ISOLATE_CPU_MEM_L | 0.546 | – | – |
ISOLATE_MEM_5V | 0.600 | – | – |
ITS_PLUGGED_IN | 1.151 | – | – |
JTAG_ISP_TCK | 0.495 | – | – |
JTAG_ISP_TDI | 0.495 | – | – |
JTAG_ISP_TDO | 0.495 | – | – |
JTAG_TBT_TCK | 0.566 | – | – |
JTAG_TBT_TDI | 0.656 | – | – |
JTAG_TBT_TDO | 0.658 | – | – |
JTAG_TBT_TMS | 0.654 | – | – |
JTAG_TBT_TMS_PCH | 0.488 | – | – |
LCD_SHOULD_ON_R | 1.329 | – | – |
LDO_DDRVTTS0_SNS | 0.561 | – | – |
LED_RETURN_1 | 1.164 | – | – |
LED_RETURN_2 | 1.164 | – | – |
LED_RETURN_3 | 1.151 | – | – |
LED_RETURN_4 | 1.146 | – | – |
LED_RETURN_5 | 1.132 | – | – |
LED_RETURN_6 | 1.123 | – | – |
LPC_AD_R<0> | 0.525 | – | – |
LPC_AD_R<1> | 0.521 | – | – |
LPC_AD_R<2> | 0.522 | – | – |
LPC_AD_R<3> | 0.523 | – | – |
LPC_AD<0> | 0.555 | – | – |
LPC_AD<1> | 0.551 | – | – |
LPC_AD<2> | 0.552 | – | – |
LPC_AD<3> | 0.551 | – | – |
LPC_CLK33M_LPCPLUS | 0.600 | – | – |
LPC_CLK33M_LPCPLUS_R | 0.568 | – | – |
LPC_CLK33M_SMC | 0.592 | – | – |
LPC_CLK33M_SMC_R | 0.565 | – | – |
LPC_FRAME_L | 0.551 | – | – |
LPC_FRAME_R_L | 0.520 | – | – |
LPC_PWRDWN_L | 0.642 | – | – |
LPC_SERIRQ | 0.617 | – | – |
LPCPLUS_GPIO | 0.789 | – | – |
LVDS_BKLT_PWM_RC | 0.561 | – | – |
MAX9119_NEG | 0.699 | – | – |
MAX9119_OUT | 0.704 | – | – |
MAX9119_POS | 0.703 | – | – |
MAX97220_C1N | 0.861 | – | – |
MAX97220_C1P | 0.550 | – | – |
MAX97220_INL_N | OL | – | – |
MAX97220_INL_P | OL | – | – |
MAX97220_INR_N | OL | – | – |
MAX97220_INR_P | OL | – | – |
MAX97220_OUTL | OL | – | – |
MAX97220_OUTL_ZOBEL | 0.034 | – | 34.400R |
MAX97220_OUTR | 1.325 | – | – |
MAX97220_OUTR_ZOBEL | 0.034 | – | 34.300R |
MAX97220_PVSS | 1.450 | – | – |
MAX97220_SHDN_L | 0.611 | – | – |
MEM_A_A<1> | 0.196 | – | – |
MEM_A_A<3> | 0.200 | – | – |
MEM_A_A<7> | 0.194 | – | – |
MEM_A_A<8> | OL | – | – |
MEM_A_A<9> | 0.200 | – | – |
MEM_A_A<10> | 0.193 | – | – |
MEM_A_A<12> | 0.198 | – | – |
MEM_A_A<13> | 0.199 | – | – |
MEM_A_A<15> | 0.198 | – | – |
MEM_A_BA<2> | 0.199 | – | – |
MEM_A_CAS_L | 0.203 | – | – |
MEM_A_CKE<0> | 0.200 | – | – |
MEM_A_CLK_N<1> | 0.232 | – | – |
MEM_A_CLK_P<0> | 0.231 | – | – |
MEM_A_CS_L<0> | 0.190 | – | – |
MEM_A_CS_L<1> | 0.191 | – | – |
MEM_A_DQ<0> | 0.239 | – | – |
MEM_A_DQ<2> | 0.241 | – | – |
MEM_A_DQ<3> | 0.242 | – | – |
MEM_A_DQ<4> | 0.241 | – | – |
MEM_A_DQ<5> | 0.244 | – | – |
MEM_A_DQ<8> | 0.243 | – | – |
MEM_A_DQ<9> | 0.239 | – | – |
MEM_A_DQ<10> | 0.241 | – | – |
MEM_A_DQ<11> | 0.241 | – | – |
MEM_A_DQ<12> | 0.244 | – | – |
MEM_A_DQ<13> | 0.241 | – | – |
MEM_A_DQ<14> | 0.236 | – | – |
MEM_A_DQ<15> | 0.245 | – | – |
MEM_A_DQ<16> | 0.234 | – | – |
MEM_A_DQ<17> | 0.238 | – | – |
MEM_A_DQ<18> | 0.244 | – | – |
MEM_A_DQ<19> | 0.239 | – | – |
MEM_A_DQ<20> | 0.238 | – | – |
MEM_A_DQ<21> | 0.239 | – | – |
MEM_A_DQ<23> | 0.241 | – | – |
MEM_A_DQ<24> | 0.234 | – | – |
MEM_A_DQ<26> | 0.238 | – | – |
MEM_A_DQ<27> | 0.238 | – | – |
MEM_A_DQ<28> | 0.237 | – | – |
MEM_A_DQ<29> | 0.238 | – | – |
MEM_A_DQ<30> | 0.240 | – | – |
MEM_A_DQ<33> | 0.229 | – | – |
MEM_A_DQ<34> | 0.229 | – | – |
MEM_A_DQ<36> | 0.230 | – | – |
MEM_A_DQ<37> | 0.232 | – | – |
MEM_A_DQ<38> | 0.231 | – | – |
MEM_A_DQ<39> | 0.234 | – | – |
MEM_A_DQ<41> | 0.228 | – | – |
MEM_A_DQ<42> | 0.232 | – | – |
MEM_A_DQ<43> | 0.229 | – | – |
MEM_A_DQ<44> | 0.231 | – | – |
MEM_A_DQ<45> | 0.230 | – | – |
MEM_A_DQ<46> | 0.229 | – | – |
MEM_A_DQ<47> | 0.230 | – | – |
MEM_A_DQ<48> | 0.227 | – | – |
MEM_A_DQ<49> | 0.230 | – | – |
MEM_A_DQ<50> | 0.229 | – | – |
MEM_A_DQ<51> | 0.231 | – | – |
MEM_A_DQ<52> | 0.228 | – | – |
MEM_A_DQ<53> | 0.231 | – | – |
MEM_A_DQ<54> | 0.228 | – | – |
MEM_A_DQ<55> | 0.232 | – | – |
MEM_A_DQ<56> | 0.228 | – | – |
MEM_A_DQ<58> | 0.227 | – | – |
MEM_A_DQ<60> | 0.228 | – | – |
MEM_A_DQ<61> | 0.231 | – | – |
MEM_A_DQ<62> | 0.231 | – | – |
MEM_A_DQ<63> | 0.230 | – | – |
MEM_A_DQS_N<0> | 0.240 | – | – |
MEM_A_DQS_N<1> | 0.241 | – | – |
MEM_A_DQS_N<3> | 0.239 | – | – |
MEM_A_DQS_N<4> | 0.231 | – | – |
MEM_A_DQS_P<1> | 0.241 | – | – |
MEM_A_DQS_P<2> | 0.237 | – | – |
MEM_A_DQS_P<3> | 0.238 | – | – |
MEM_A_DQS_P<5> | 0.236 | – | – |
MEM_A_DQS_P<6> | 0.227 | – | – |
MEM_A_DQS_P<7> | 0.228 | – | – |
MEM_A_SA<0> | OL | – | – |
MEM_A_SA<1> | OL | – | – |
MEM_A_WE_L | OL | – | – |
MEM_B_A<0> | 0.192 | – | – |
MEM_B_A<1> | 0.193 | – | – |
MEM_B_A<2> | 0.194 | – | – |
MEM_B_A<3> | 0.193 | – | – |
MEM_B_A<4> | 0.197 | – | – |
MEM_B_A<5> | 0.193 | – | – |
MEM_B_A<6> | 0.194 | – | – |
MEM_B_A<7> | 0.195 | – | – |
MEM_B_A<9> | 0.195 | – | – |
MEM_B_A<10> | 0.193 | – | – |
MEM_B_A<11> | 0.197 | – | – |
MEM_B_A<12> | 0.197 | – | – |
MEM_B_A<13> | 0.193 | – | – |
MEM_B_A<14> | 0.196 | – | – |
MEM_B_A<15> | 0.197 | – | – |
MEM_B_BA<0> | 0.191 | – | – |
MEM_B_BA<1> | 0.193 | – | – |
MEM_B_CAS_L | 0.193 | – | – |
MEM_B_CKE<0> | 0.194 | – | – |
MEM_B_CKE<1> | 0.197 | – | – |
MEM_B_CLK_N<1> | 0.235 | – | – |
MEM_B_CLK_P<0> | 0.230 | – | – |
MEM_B_CS_L<0> | 0.191 | – | – |
MEM_B_CS_L<1> | 0.193 | – | – |
MEM_B_DQ<1> | 0.236 | – | – |
MEM_B_DQ<2> | 0.238 | – | – |
MEM_B_DQ<3> | 0.239 | – | – |
MEM_B_DQ<4> | 0.239 | – | – |
MEM_B_DQ<5> | 0.241 | – | – |
MEM_B_DQ<6> | 0.238 | – | – |
MEM_B_DQ<10> | 0.238 | – | – |
MEM_B_DQ<11> | 0.237 | – | – |
MEM_B_DQ<12> | 0.236 | – | – |
MEM_B_DQ<13> | 0.238 | – | – |
MEM_B_DQ<14> | 0.239 | – | – |
MEM_B_DQ<15> | 0.239 | – | – |
MEM_B_DQ<17> | 0.234 | – | – |
MEM_B_DQ<18> | 0.237 | – | – |
MEM_B_DQ<19> | 0.237 | – | – |
MEM_B_DQ<20> | 0.235 | – | – |
MEM_B_DQ<21> | 0.236 | – | – |
MEM_B_DQ<22> | 0.235 | – | – |
MEM_B_DQ<23> | 0.236 | – | – |
MEM_B_DQ<24> | 0.236 | – | – |
MEM_B_DQ<25> | 0.237 | – | – |
MEM_B_DQ<26> | 0.238 | – | – |
MEM_B_DQ<27> | 0.238 | – | – |
MEM_B_DQ<28> | 0.240 | – | – |
MEM_B_DQ<29> | 0.236 | – | – |
MEM_B_DQ<30> | 0.236 | – | – |
MEM_B_DQ<31> | 0.239 | – | – |
MEM_B_DQ<32> | 0.226 | – | – |
MEM_B_DQ<33> | 0.227 | – | – |
MEM_B_DQ<34> | 0.228 | – | – |
MEM_B_DQ<37> | 0.230 | – | – |
MEM_B_DQ<39> | 0.230 | – | – |
MEM_B_DQ<40> | 0.238 | – | – |
MEM_B_DQ<41> | 0.229 | – | – |
MEM_B_DQ<42> | 0.231 | – | – |
MEM_B_DQ<43> | 0.229 | – | – |
MEM_B_DQ<44> | 0.231 | – | – |
MEM_B_DQ<45> | 0.230 | – | – |
MEM_B_DQ<46> | 0.227 | – | – |
MEM_B_DQ<47> | 0.228 | – | – |
MEM_B_DQ<49> | 0.227 | – | – |
MEM_B_DQ<50> | 0.226 | – | – |
MEM_B_DQ<51> | 0.230 | – | – |
MEM_B_DQ<52> | 0.229 | – | – |
MEM_B_DQ<53> | 0.227 | – | – |
MEM_B_DQ<54> | 0.229 | – | – |
MEM_B_DQ<55> | 0.227 | – | – |
MEM_B_DQ<56> | 0.225 | – | – |
MEM_B_DQ<57> | 0.226 | – | – |
MEM_B_DQ<58> | 0.227 | – | – |
MEM_B_DQ<60> | 0.227 | – | – |
MEM_B_DQ<61> | 0.233 | – | – |
MEM_B_DQ<62> | 0.227 | – | – |
MEM_B_DQ<63> | 0.232 | – | – |
MEM_B_DQS_N<1> | 0.238 | – | – |
MEM_B_DQS_N<3> | 0.239 | – | – |
MEM_B_DQS_N<4> | 0.229 | – | – |
MEM_B_DQS_N<5> | 0.229 | – | – |
MEM_B_DQS_N<6> | 0.227 | – | – |
MEM_B_DQS_P<0> | 0.236 | – | – |
MEM_B_DQS_P<1> | 0.237 | – | – |
MEM_B_DQS_P<3> | 0.239 | – | – |
MEM_B_DQS_P<5> | 0.231 | – | – |
MEM_B_DQS_P<7> | 0.228 | – | – |
MEM_B_ODT<1> | 0.188 | – | – |
MEM_B_RAS_L | 0.192 | – | – |
MEM_B_SA<0> | OL | – | – |
MEM_B_SA<1> | OL | – | – |
MEM_EVENT_L | 0.750 | – | – |
MEM_RESET_L | 0.771 | – | – |
MEM_VDD_SEL_1V5_L | 0.514 | – | – |
MEM_VREFCA_A_RC | 0.026 | – | 25.700R |
MEM_VREFCA_B_RC | 0.028 | – | 25.300R |
MEM_VREFDQ_A_RC | 0.026 | – | 25.400R |
MEM_VREFDQ_B_RC | 0.029 | – | 25.300R |
MEMRESET_ISOL_LS5V_L | 0.618 | – | – |
MIPI_RESISTOR | 0.796 | – | – |
MUTE_CONTROL | OL | – | – |
MUTE_SWITCH | OL | – | – |
NC | OL | – | – |
P1V2_S4_EN | 0.780 | – | – |
P1V5_S0_FET_GATE | 0.682 | – | – |
P1V8_S4_EN | 0.780 | – | – |
P3V3_S0_OOB | OL | – | – |
P3V3_S0_SSD_FET_RAMP | 0.645 | – | – |
P3V3AP_VMON | 0.463 | – | – |
P3V3ENET_SS | OL | – | – |
P3V42G3H_FB | 0.720 | – | – |
P3V42G3H_SHDN_L | 0.718 | – | – |
P3V42G3H_SW | 0.321 | – | – |
P5V_S0_FET_RAMP | 0.646 | – | – |
P5V_S0_HDD_FET_RAMP | 0.734 | – | – |
P12V_S0_FET_GATE | 0.687 | – | – |
P12V_S0_FET_GATE_R | 0.686 | – | – |
PCA9557D_RESET_L | 0.585 | – | – |
PCH_A20GATE | 0.540 | – | – |
PCH_CAM_EXT_BOOT_L | 0.518 | – | – |
PCH_CAM_EXT_BOOT_R_L | 0.554 | – | – |
PCH_CAM_RESET | 0.520 | – | – |
PCH_CAM_RESET_R | 0.554 | – | – |
PCH_CLK14P3M_REFCLK | 0.416 | – | – |
PCH_CLK32K_RTCX1 | 0.811 | – | – |
PCH_CLK32K_RTCX2 | 0.809 | – | – |
PCH_CLK32K_RTCX2_R | 0.808 | – | – |
PCH_CLK33M_PCIIN | 0.600 | – | – |
PCH_CLK33M_PCIOUT | 0.568 | – | – |
PCH_CLK96M_DOTN | 0.795 | – | – |
PCH_CLK96M_DOTP | 0.794 | – | – |
PCH_CLK100M_SATAN | 0.794 | – | – |
PCH_CLK100M_SATAP | 0.794 | – | – |
PCH_CLKIN_GNDN | 0.795 | – | – |
PCH_CLKIN_GNDP | 0.794 | – | – |
PCH_CLKRQ3_L_GPIO25 | 0.509 | – | – |
PCH_CLKRQ5_L_GPIO44 | 0.570 | – | – |
PCH_CLKRQ7_L_GPIO46 | 0.563 | – | – |
PCH_DIFFCLK_BIASREF | 0.745 | – | – |
PCH_DMI_RCOMP | 0.781 | – | – |
PCH_DSWVRMEN | 0.796 | – | – |
PCH_FDI_RCOMP | 0.783 | – | – |
PCH_GPIO10 | 0.508 | – | – |
PCH_GPIO16 | 0.540 | – | – |
PCH_GPIO31 | 0.630 | – | – |
PCH_GPIO36 | 0.515 | – | – |
PCH_GPIO41 | 0.508 | – | – |
PCH_GPIO42 | 0.506 | – | – |
PCH_GPIO49 | 0.551 | – | – |
PCH_GPIO70 | 0.684 | – | – |
PCH_GPIO71 | 0.673 | – | – |
PCH_GPIO72 | 0.527 | – | – |
PCH_INTRUDER_L | 0.797 | – | – |
PCH_INTVRMEN_L | 0.799 | – | – |
PCH_PCIE_RCOMP | 0.782 | – | – |
PCH_PECI | 0.587 | – | – |
PCH_PEGCLKRQA_L_GPIO47 | 0.567 | – | – |
PCH_PEGCLKRQB_L_GPIO56 | 0.570 | – | – |
PCH_RCIN_L | 0.798 | – | – |
PCH_RI_L | 0.627 | – | – |
PCH_SATALED_L | 0.695 | – | – |
PCH_SMBALERT_L | 0.628 | – | – |
PCH_SML0ALERT_L | 0.626 | – | – |
PCH_SML1ALERT_L | 0.630 | – | – |
PCH_SPKR | 0.552 | – | – |
PCH_SRTCRST_L | 0.795 | – | – |
PCH_STRP_TOPBLK_SWP_L | 0.463 | – | – |
PCH_SUSACK_L | 0.548 | – | – |
PCH_SUSWARN_L | 0.426 | – | – |
PCH_TD_IREF | 0.793 | – | – |
PCH_USB_RBIAS | 0.025 | – | 23.000R |
PCI_INTA_L | 0.673 | – | – |
PCI_INTB_L | 0.686 | – | – |
PCI_INTC_L | 0.685 | – | – |
PCI_INTD_L | 0.702 | – | – |
PCIE_AP_D2R_N | 0.372 | – | – |
PCIE_AP_D2R_P | 0.376 | – | – |
PCIE_AP_R2D_C_P | 0.388 | – | – |
PCIE_AP_R2D_N | OL | – | – |
PCIE_AP_R2D_P | OL | – | – |
PCIE_CLK100M_AP_N | 0.282 | – | – |
PCIE_CLK100M_AP_P | 0.282 | – | – |
PCIE_CLK100M_ENET_P | 0.281 | – | – |
PCIE_CLK100M_PCHN | 0.793 | – | – |
PCIE_CLK100M_PCHP | 0.794 | – | – |
PCIE_CLK100M_SSD_N | 0.279 | – | – |
PCIE_CLK100M_TBT_P | 0.280 | – | – |
PCIE_ENET_D2R_C_N | 0.520 | – | – |
PCIE_ENET_D2R_C_P | 0.519 | – | – |
PCIE_ENET_D2R_N | 0.370 | – | – |
PCIE_ENET_D2R_P | 0.390 | – | – |
PCIE_ENET_R2D_C_P | 0.390 | – | – |
PCIE_ENET_R2D_N | 0.505 | – | – |
PCIE_ENET_R2D_P | 0.502 | – | – |
PCIE_TBT_D2R_C_N<0> | 0.312 | – | – |
PCIE_TBT_D2R_C_N<1> | 0.313 | – | – |
PCIE_TBT_D2R_C_N<2> | 0.313 | – | – |
PCIE_TBT_D2R_C_N<3> | 0.312 | – | – |
PCIE_TBT_D2R_C_P<0> | 0.314 | – | – |
PCIE_TBT_D2R_C_P<2> | 0.312 | – | – |
PCIE_TBT_D2R_C_P<3> | 0.312 | – | – |
PCIE_TBT_D2R_N<0> | 0.370 | – | – |
PCIE_TBT_D2R_N<1> | 0.371 | – | – |
PCIE_TBT_D2R_N<2> | 0.372 | – | – |
PCIE_TBT_D2R_N<3> | 0.376 | – | – |
PCIE_TBT_D2R_P<0> | 0.371 | – | – |
PCIE_TBT_D2R_P<2> | 0.372 | – | – |
PCIE_TBT_D2R_P<3> | 0.378 | – | – |
PCIE_TBT_R2D_C_N<0> | 0.388 | – | – |
PCIE_TBT_R2D_C_N<1> | 0.388 | – | – |
PCIE_TBT_R2D_C_N<2> | 0.388 | – | – |
PCIE_TBT_R2D_C_N<3> | 0.389 | – | – |
PCIE_TBT_R2D_C_P<0> | 0.386 | – | – |
PCIE_TBT_R2D_C_P<1> | 0.384 | – | – |
PCIE_TBT_R2D_C_P<2> | 0.388 | – | – |
PCIE_TBT_R2D_C_P<3> | 0.391 | – | – |
PCIE_TBT_R2D_N<0> | 0.379 | – | – |
PCIE_TBT_R2D_N<1> | 0.382 | – | – |
PCIE_TBT_R2D_N<2> | 0.387 | – | – |
PCIE_TBT_R2D_N<3> | 0.383 | – | – |
PCIE_TBT_R2D_P<0> | 0.382 | – | – |
PCIE_TBT_R2D_P<1> | 0.382 | – | – |
PCIE_TBT_R2D_P<2> | 0.382 | – | – |
PCIE_TBT_R2D_P<3> | 0.381 | – | – |
PCIE_WAKE_L | 0.513 | – | – |
PEG_CLKREQ_L | 0.554 | – | – |
PGND_BKLT | 0.000 | – | – |
PLT_RESET_L | 0.553 | – | – |
PLT_RST_BUF_L | 0.417 | – | – |
PM_CLK32K_SUSCLK_R | 0.660 | – | – |
PM_CLKRUN_L | 0.534 | – | – |
PM_DSW_PWRGD | 0.700 | – | – |
PM_EN_ENET_L | 0.574 | – | – |
PM_EN_FET_P1V35_S0 | 0.651 | – | – |
PM_EN_FET_P3V3_S0 | 0.561 | – | – |
PM_EN_FET_P3V3_S4 | 0.525 | – | – |
PM_EN_FET_P5V_S0 | 0.452 | – | – |
PM_EN_FET_P12V_S0 | 0.582 | – | – |
PM_EN_FET_REG_P1V5_S0 | 0.629 | – | – |
PM_EN_REG_CPUVCC_S0 | 0.530 | – | – |
PM_EN_REG_P1V05_S0 | 0.543 | – | – |
PM_EN_REG_P1V05_S0_R | 0.543 | – | – |
PM_EN_REG_P3V3_S5 | 0.521 | – | – |
PM_EN_REG_P5V_S4 | 0.510 | – | – |
PM_EN_REG_VDDQ_S3 | 0.502 | – | – |
PM_EN_S0_R | 0.493 | – | – |
PM_EN_S4 | 0.506 | – | – |
PM_EN_USB_PWR | 0.460 | – | – |
PM_MEM_PWRGD | 0.512 | – | – |
PM_PCH_PWROK | 0.501 | – | – |
PM_PCH_SYS_PWROK | 0.733 | – | – |
PM_PCH_SYS_PWROK_R | 0.537 | – | – |
PM_PGOOD_FET_P1V35_S0 | 0.655 | – | – |
PM_PGOOD_FET_P3V3_S0 | 0.652 | – | – |
PM_PGOOD_FET_P5V_S0 | 0.558 | – | – |
PM_PGOOD_FET_P12V_S0 | 0.548 | – | – |
PM_PGOOD_FET_REG_P1V5_S0 | 0.617 | – | – |
PM_PGOOD_REG_CPUVCC_S0 | 0.638 | – | – |
PM_PGOOD_REG_GPU_P1V35_S0 | 0.653 | – | – |
PM_PGOOD_REG_P1V05_S0 | 0.530 | – | – |
PM_PGOOD_REG_P3V3_S5 | 0.554 | – | – |
PM_PGOOD_REG_P5V_S4 | 0.462 | – | – |
PM_PGOOD_REG_VDDQ_S3 | 0.571 | – | – |
PM_PWRBTN_L | 0.605 | – | – |
PM_RSMRST_PCH_L | 0.535 | – | – |
PM_RSMRST_PCH_L_R | 0.535 | – | – |
PM_SLP_S3_BUF_L | 0.562 | – | – |
PM_SLP_S3_L | 0.440 | – | – |
PM_SLP_S4_L | 0.637 | – | – |
PM_SLP_S5_L | 0.642 | – | – |
PM_SLP_SUS_L | 0.460 | – | – |
PM_SYSRST_L | 0.636 | – | – |
PM_THRMTRIP_L | 0.222 | – | – |
PM_THRMTRIP_L_R | 0.545 | – | – |
PP1V2_ENET_INTREG | 0.283 | – | – |
PP1V2_ENET_PHY_AVDDL | 0.283 | – | – |
PP1V2_ENET_PHY_GPHYPLL | 0.288 | – | – |
PP1V2_ENET_PHY_PCIEPLL | 0.284 | – | – |
PP1V2_G3H_SMC_VDDC | 0.513 | – | – |
PP1V2_S4_CAMERA | 0.327 | – | – |
PP1V2_S4_CAMFILT | 0.342 | – | – |
PP1V2_S4_F_R | 0.327 | – | – |
PP1V05_S0 | 0.079 | – | 79.100R |
PP1V5_S0 | 0.362 | – | – |
PP1V05_S0_PCH_VCC_CLK_F | 0.083 | – | – |
PP1V05_S0_PCH_VCC_CLK_R | 0.083 | – | – |
PP1V05_TBTCIO | 0.138 | – | – |
PP1V05_TBTLC | 0.117 | – | – |
PP1V8_S4_CAMERA | 0.438 | – | – |
PP1V8_S4_CAMERA_F | 0.439 | – | – |
PP3V3_DMIC_CONN | 0.346 | – | – |
PP3V3_ENET | 0.358 | – | 0.002R |
PP3V3_ENET_PHY_AVDDH | 0.358 | – | – |
PP3V3_ENET_PHY_BIASVDDH | 0.284 | – | 0.002R |
PP3V3_G3 | 0.573 | – | – |
PP3V3_G3H_AVREF_SMC | 0.609 | – | – |
PP3V3_G3H_BT_FET | 0.530 | – | – |
PP3V3_G3H_BT_FLT | 0.530 | – | – |
PP3V3_G3H_SMC_VDDA | 0.321 | – | – |
PP3V3_S0 | 0.346 | – | – |
PP3V3_S0_BKLT_VDDIO_R | 0.345 | – | – |
PP3V3_S0_SSD | 0.462 | – | – |
PP3V3_S0_SSD_FLT | 0.462 | – | – |
PP3V3_S0_SW_SD_PWR | 0.559 | – | – |
PP3V3_S3_VREFMRGN | 0.330 | – | – |
PP3V3_S4 | 0.330 | – | – |
PP3V3_S4_ALS_F | 0.330 | – | – |
PP3V3_S4_AP | 0.330 | – | – |
PP3V3_S4_AP_FET | 0.502 | – | – |
PP3V3_S4_AP_FLT | 0.502 | – | – |
PP3V3_S4_CAMFILT | 0.330 | – | – |
PP3V3_S5 | 0.141 | – | – |
PP3V3_S5_XDP_R | 0.105 | – | – |
PP3V3_TBTLC | 0.416 | – | – |
PP3V3R1V8_ENET_LR_OUT | 0.540 | – | – |
PP3V3RHV_SW_TBTAPWR | 0.560 | – | – |
PP3V3RHV_SW_TBTBPWR | 0.559 | – | – |
PP3V42_G3H | 0.321 | – | – |
PP3V42_G3H_SMC_SPVSR | 0.378 | – | – |
PP4V5_AUDIO_ANALOG | 0.492 | – | – |
PP5V_AUDIO_HPAMP | 0.412 | – | – |
PP5V_S0 | 0.412 | – | – |
PP5V_S0_BKLT_R | 0.410 | – | – |
PP5V_S0_HDD | 0.591 | – | – |
PP5V_S4 | 0.156 | – | – |
PP5V_S4_CAMERA_F | 0.160 | – | – |
PP5V_S4_EXTA_F | 0.540 | – | – |
PP5V_S4_EXTA_ILIM | 0.540 | – | – |
PP5V_S4_EXTB_F | 0.538 | – | – |
PP5V_S4_EXTB_ILIM | 0.538 | – | – |
PP5V_S4_EXTC_F | 0.538 | – | – |
PP5V_S4_EXTC_ILIM | 0.538 | – | – |
PP5V_S4_EXTD_F | 0.536 | – | – |
PP5V_S4_EXTD_ILIM | 0.536 | – | – |
PP5V_S5 | 0.458 | – | – |
PP12V_ACDC | 0.567 | – | – |
PP12V_BKLT_FUSED | 0.458 | – | – |
PP12V_BKLT_SNS | 0.458 | – | – |
PP12V_G3H | 0.567 | – | – |
PP12V_LCD | 0.461 | – | – |
PP12V_LCD_F | 0.461 | – | – |
PP12V_S0 | 0.464 | – | – |
PP12V_S0_BKLT_FILT | 0.457 | – | – |
PP12V_S0_BKLT_PWR | 0.168 | – | – |
PP12V_S0_BKLT_PWR_R | 0.167 | – | – |
PP12V_S0_CPUVCC_FLT | 0.464 | – | – |
PP12V_S0_FAN_0_FILT | 0.464 | – | – |
PP12V_S5 | 0.537 | – | – |
PPCPUVCC_S0_CPU | 0.011 | – | 10.900R |
PPCPUVCC_S0_SENSE_1 | 0.011 | – | 10.900R |
PPCPUVCC_S0_SENSE_2 | 0.011 | – | 10.900R |
PPCPUVCC_S0_SENSE_3 | 0.011 | – | 10.900R |
PPDDRVTT_S0 | 0.561 | – | – |
PPHDD_S0 | 0.591 | – | – |
PPHV_SW_TBTAPWR | 0.560 | – | – |
PPHV_SW_TBTBPWR | 0.559 | – | – |
PPSSD_S0 | 0.462 | – | – |
PPVBATT_G3_RTC | OL | – | – |
PPVCCIO_S0_CPU | 0.010 | – | 10.000R |
PPVCOMP_S0_CPU | 0.020 | – | 20.000R |
PPVDDQ_S0 | 0.162 | – | – |
PPVDDQ_S0_CPU | 0.162 | – | – |
PPVDDQ_S3 | 0.327 | – | – |
PPVDDQ_S3_DDR | 0.327 | 1.300 | – |
PPVOUT_S0_PCH_DCPRTC | 0.716 | – | – |
PPVOUT_S0_PCH_DCPSST | 0.470 | – | – |
PPVOUT_S5_PCH_DCPSUSBYP | 0.383 | – | – |
PPVOUT_S5_PCH_DCPSUSBYP_R | 0.382 | – | – |
PPVREF_S3_MEM_VREFCA_A | 0.552 | – | – |
PPVREF_S3_MEM_VREFCA_B | 0.553 | – | – |
PPVREF_S3_MEM_VREFDQ_A | 0.553 | – | – |
PPVREF_S3_MEM_VREFDQ_B | 0.559 | – | – |
PU_U8500 | 0.716 | – | – |
PWR_BTN_R | 0.848 | – | – |
Q6170_N_G | OL | – | – |
Q6170_N_S | OL | – | – |
Q6170_P_G | OL | – | – |
Q6170_P_S | OL | – | – |
Q6171_N_G | OL | – | – |
Q6171_N_S | OL | – | – |
Q6171_P_G | OL | – | – |
Q6171_P_S | OL | – | – |
REG_BOOT_CPUVCC_1 | 0.603 | – | – |
REG_BOOT_CPUVCC_1_RC | 0.603 | – | – |
REG_BOOT_CPUVCC_2 | 0.606 | – | – |
REG_BOOT_CPUVCC_2_RC | 0.606 | – | – |
REG_BOOT_CPUVCC_3 | 0.603 | – | – |
REG_BOOT_CPUVCC_3_RC | 0.602 | – | – |
REG_BOOT_P1V05S0 | 0.574 | – | – |
REG_BOOT_P1V05S0_RC | 0.574 | – | – |
REG_BOOT_P3V3S5 | 0.599 | – | – |
REG_BOOT_P3V3S5_RC | 0.599 | – | – |
REG_BOOT_P5VS4 | 0.603 | – | – |
REG_BOOT_P5VS4_RC | 0.603 | – | – |
REG_BOOT_VDDQS3 | 0.612 | – | – |
REG_BOOT_VDDQS3_RC | 0.612 | – | – |
REG_CPUVCC_COMP | 0.625 | – | – |
REG_CPUVCC_DVC | 0.620 | – | – |
REG_CPUVCC_FB | 0.569 | – | – |
REG_CPUVCC_FDVID | 0.622 | – | – |
REG_CPUVCC_HFCOMP | 0.605 | – | – |
REG_CPUVCC_IMON | 0.612 | – | – |
REG_CPUVCC_IMON_R | 0.674 | – | – |
REG_CPUVCC_IMX | 0.610 | – | – |
REG_CPUVCC_MEMVRSEL | 0.000 | – | – |
REG_CPUVCC_NPSI | 0.618 | – | – |
REG_CPUVCC_PSICOMP | 0.582 | – | – |
REG_CPUVCC_RGND | 0.013 | – | 12.500R |
REG_CPUVCC_RSET | 0.620 | – | – |
REG_CPUVCC_TM | 0.598 | – | – |
REG_CPUVCC_TMX | 0.619 | – | – |
REG_CPUVCC_VIN | 0.661 | – | – |
REG_CPUVCC_VRHOT_L | 0.072 | – | 70.700R |
REG_CPUVCC_VSEN | 0.024 | – | 23.400R |
REG_ISENVCC_1_N | 0.011 | – | 10.900R |
REG_ISENVCC_1_NR | 0.568 | – | – |
REG_ISENVCC_1_P | 0.011 | – | 10.900R |
REG_ISENVCC_2_N | – | – | 10.900R |
REG_ISENVCC_2_NR | 0.569 | – | – |
REG_ISENVCC_2_P | – | – | 10.900R |
REG_ISENVCC_3_N | – | – | 10.900R |
REG_ISENVCC_3_NR | 0.569 | – | – |
REG_ISENVCC_3_P | – | – | 10.900R |
REG_LGATE_P1V05S0 | 0.449 | – | – |
REG_LGATE_P3V3S5 | 0.047 | – | – |
REG_LGATE_P5VS4 | 0.473 | – | – |
REG_LGATE_VDDQS3 | 0.434 | – | – |
REG_P1V5S0_ADJ | 0.588 | – | – |
REG_P1V05S0_FB | 0.522 | – | – |
REG_P1V05S0_FB_R | 0.082 | – | 81.200R |
REG_P1V05S0_FSEL | 0.548 | – | – |
REG_P1V5S0_ISET | 0.617 | – | – |
REG_P1V05S0_OCSET | 0.546 | – | – |
REG_P1V05S0_RTN | 0.527 | – | – |
REG_P1V05S0_RTN_R | 0.000 | – | – |
REG_P1V05S0_SREF | 0.545 | – | – |
REG_P1V5S0_SS | 0.639 | – | – |
REG_P3V3S5_FB | 0.539 | – | – |
REG_P3V3S5_FSET | 0.543 | – | – |
REG_P3V3S5_ISEN | 0.544 | – | – |
REG_P3V3S5_OCSET | 0.545 | – | – |
REG_P3V3S5_VOUT | 0.143 | – | – |
REG_P3V3S5_VOUT_R | 1.124 | – | – |
REG_P5VS4_FB | OL | – | – |
REG_P5VS4_FSET | 0.544 | – | – |
REG_P5VS4_ISEN | 0.543 | – | – |
REG_P5VS4_OCSET | 0.543 | – | – |
REG_P5VS4_VOUT | 0.158 | – | – |
REG_P5VS4_VOUT_R | 1.142 | – | – |
REG_PHASE_CPUVCC_1 | 0.010 | – | – |
REG_PHASE_CPUVCC_2 | 0.011 | – | – |
REG_PHASE_CPUVCC_3 | 0.011 | – | – |
REG_PHASE_CPUVCC1 | 0.011 | – | 10.900R |
REG_PHASE_CPUVCC2 | 0.011 | – | 10.900R |
REG_PHASE_CPUVCC3 | 0.011 | – | 10.900R |
REG_PHASE_P1V05S0_L | 0.080 | – | 79.100R |
REG_PHASE_P3V3S5 | 0.141 | – | – |
REG_PHASE_P5VS4 | 0.156 | – | – |
REG_PHASE_VDDQS3 | 0.326 | – | – |
REG_PHASE_VDDQS3_L | 0.327 | – | – |
REG_PVCC_U7400 | 0.415 | – | – |
REG_PWM_CPUVCC_1 | 0.528 | – | – |
REG_PWM_CPUVCC_1_R | 0.528 | – | – |
REG_PWM_CPUVCC_2 | 0.530 | – | – |
REG_PWM_CPUVCC_2_R | 0.531 | – | – |
REG_PWM_CPUVCC_3 | 0.529 | – | – |
REG_PWM_CPUVCC_3_R | 0.534 | – | – |
REG_PWM_CPUVCC_4_R | 0.415 | – | – |
REG_SNUBBER_CPUVCC_1 | OL | – | – |
REG_SNUBBER_CPUVCC_2 | OL | – | – |
REG_SNUBBER_CPUVCC_3 | OL | – | – |
REG_SNUBBER_P1V05S0 | OL | – | – |
REG_SNUBBER_P3V3S5 | OL | – | – |
REG_SNUBBER_P5VS4 | OL | – | – |
REG_SNUBBER_VDDQS3 | OL | – | – |
REG_THWN_2 | 0.650 | – | – |
REG_THWN_3 | 0.648 | – | – |
REG_U7600_FCCM | 0.544 | – | – |
REG_U7600_FCCM_R | OL | – | – |
REG_UGATE_P1V05S0 | 0.578 | – | – |
REG_UGATE_P1V05S0_R | 0.579 | – | – |
REG_UGATE_P3V3S5 | 0.537 | – | – |
REG_UGATE_P5VS4 | 0.585 | – | – |
REG_UGATE_VDDQS3 | 0.783 | – | – |
REG_UGATE_VDDQS3_R | 0.783 | – | – |
REG_V5IN_U7300 | 0.160 | – | – |
REG_VCC_U7000 | 0.414 | – | – |
REG_VCC_U7400 | 0.422 | – | – |
REG_VCC1_U7600 | 0.516 | – | – |
REG_VCC2_U7600 | 0.459 | – | – |
REG_VDDQS3_MODE | 0.485 | – | – |
REG_VDDQS3_REFIN | 0.697 | – | – |
REG_VDDQS3_TRIP | 0.750 | – | – |
REG_VDDQS3_VDDQSNS | 0.326 | – | – |
REG_VDDQS3_VREF | 0.643 | – | – |
REG_VDDQS3_VTTREF | 0.502 | – | – |
REG_VIN_U7600 | 0.539 | – | – |
REG_ZCDEN | 0.483 | – | – |
RTC_RESET_L | 0.769 | – | – |
RTC_RESET_L_R | 0.616 | – | – |
SATA_HDD_D2R_C_N | OL | – | – |
SATA_HDD_D2R_C_P | OL | – | – |
SATA_HDD_D2R_N | 0.371 | – | – |
SATA_HDD_D2R_P | 0.374 | – | – |
SATA_HDD_R2D_C_N | 0.389 | – | – |
SATA_HDD_R2D_C_P | 0.388 | – | – |
SATA_HDD_R2D_N | OL | – | – |
SATA_HDD_R2D_P | OL | – | – |
SATA_PWR_L | 0.614 | – | – |
SATALED_R_L | OL | – | – |
SATARDRVR_EN | 0.537 | – | – |
SD_DETECT_LVL | 0.462 | – | – |
SDCONN_CLK | 0.545 | – | – |
SDCONN_CLK_R | 0.547 | – | – |
SDCONN_CMD | 0.548 | – | – |
SDCONN_DATA<0> | 0.549 | – | – |
SDCONN_DATA<1> | 0.546 | – | – |
SDCONN_DATA<2> | 0.548 | – | – |
SDCONN_DATA<3> | 0.547 | – | – |
SDCONN_DATA<4> | 0.699 | – | – |
SDCONN_DATA<5> | 0.695 | – | – |
SDCONN_DATA<6> | 0.702 | – | – |
SDCONN_DATA<7> | 0.702 | – | – |
SDCONN_DETECT_L | 0.464 | – | – |
SDCONN_ILIM | 0.572 | – | – |
SDCONN_ILIM_R | OL | – | – |
SDCONN_OC_L | 0.516 | – | – |
SDCONN_STATE_CHANGE | 0.435 | – | – |
SDCONN_WP | 0.657 | – | – |
SLG_ENET_RESET_R_L | 0.457 | – | – |
SMB_0_S0_CLK | 0.591 | – | – |
SMB_0_S0_DATA | 0.597 | – | – |
SMB_1_S0_CLK | 0.638 | – | – |
SMB_1_S0_DATA | 0.623 | – | – |
SMB_2_S4_CLK | 0.748 | – | – |
SMB_2_S4_DATA | 0.747 | – | – |
SMB_3_CLK | 0.745 | – | – |
SMB_3_DATA | 0.745 | – | – |
SMB_ALS_F_SCL | 0.748 | – | – |
SMB_ALS_F_SDA | 0.749 | – | – |
SMB_DP_TCON_SCL | 2.334 | – | – |
SMB_DP_TCON_SDA | 2.357 | – | – |
SMB_ENET_SCL | 0.713 | – | – |
SMB_ENET_SDA | 0.713 | – | – |
SMBUS_PCH_CLK | 0.488 | – | – |
SMBUS_PCH_DATA | 0.499 | – | – |
SMC_ACDC_ID | 0.746 | – | – |
SMC_ASSERT_RTCRST | 0.746 | – | – |
SMC_CLK32K | 0.675 | – | – |
SMC_CPU_CATERR_L | 0.219 | – | – |
SMC_DEBUGPRT_EN_L | 0.578 | – | – |
SMC_DEBUGPRT_RX_L | 0.679 | – | – |
SMC_DEBUGPRT_TX_L | 0.679 | – | – |
SMC_DELAYED_PWRGD | 0.703 | – | – |
SMC_EXTAL | 0.786 | – | – |
SMC_FAN_0_CTL | 0.750 | – | – |
SMC_FAN_0_TACH | 0.751 | – | – |
SMC_G3_WAKESRC_EN | 0.750 | – | – |
SMC_LRESET_L | 0.584 | – | – |
SMC_MANUAL_RST_L | 0.679 | – | – |
SMC_ONOFF_L | 0.749 | – | – |
SMC_OOB1_D2R_L | 0.662 | – | – |
SMC_OOB1_R2D_L | 0.749 | – | – |
SMC_OOB1_R2D_R_L | 1.277 | – | – |
SMC_OOB2_D2R_L | 0.751 | – | – |
SMC_OOB2_R2D_L | 0.751 | – | – |
SMC_PECI_L | 0.748 | – | – |
SMC_PECI_L_R | 0.748 | – | – |
SMC_PM_G2_EN | 0.577 | – | – |
SMC_PM_PCH_SYS_PWROK | 0.732 | – | – |
SMC_PME_S4_WAKE_L | 0.611 | – | – |
SMC_PROCHOT | 0.749 | – | – |
SMC_RESET_L | 0.586 | – | – |
SMC_RESET_R_L | 0.593 | – | – |
SMC_ROMBOOT | 1.734 | – | – |
SMC_RUNTIME_SCI_L | 0.644 | – | – |
SMC_RX_L | 0.748 | – | – |
SMC_SYS_LED | 0.749 | – | – |
SMC_TCK | 0.748 | – | – |
SMC_TDI | 0.750 | – | – |
SMC_TDO | 0.748 | – | – |
SMC_THRMTRIP | 0.746 | – | – |
SMC_TMS | 0.747 | – | – |
SMC_TOPBLK_SWP_L | 0.712 | – | – |
SMC_TX_L | 0.746 | – | – |
SMC_VCCIO_CPU_DIV2 | 0.740 | – | – |
SMC_WAKE_L | 0.754 | – | – |
SMC_WAKE_SCI_L | 0.517 | – | – |
SMC_XTAL | 0.772 | – | – |
SMC_XTAL_R | 0.773 | – | – |
SMIA_CLK_N | 0.472 | – | – |
SMIA_CLK_P | 0.473 | – | – |
SMIA_DATA_N | 0.474 | – | – |
SMIA_DATA_P | 0.472 | – | – |
SML_PCH_0_CLK | 0.609 | – | – |
SML_PCH_0_DATA | 0.611 | – | – |
SNS_ACDC_N | 0.756 | – | – |
SNS_ACDC_P | 0.757 | – | – |
SNS_HDD_N | 0.591 | – | – |
SNS_HDD_P | 0.591 | – | – |
SNS_P3V3S4_AP_N | 0.330 | – | – |
SNS_P3V3S4_AP_P | 0.330 | – | – |
SNS_P12VG3H_N | 0.567 | – | – |
SNS_P12VG3H_P | 0.567 | – | – |
SNS_PVDDQS0_N | 0.162 | – | – |
SNS_PVDDQS0_P | 0.162 | – | – |
SNS_SSD_N | 0.462 | – | – |
SNS_SSD_P | 0.462 | – | – |
SNS_T1_1_N | 0.776 | – | – |
SNS_T1_1_P | 0.780 | – | – |
SNS_T1_2_N | 0.757 | – | – |
SNS_T1_2_P | 0.756 | – | – |
SNS_T2_1_N | 0.659 | – | – |
SNS_T2_2_N | 0.659 | – | – |
SNS_T2_2_P | 0.663 | – | – |
SNS_T2_3_N | 0.659 | – | – |
SNS_T2_3_P | 0.663 | – | – |
SNS_T2_DXN | 0.659 | – | – |
SNS_VCC_XW_N | 0.000 | – | – |
SNS_VCC_XW_P | 0.010 | – | – |
SNS_VDDQS3_DDR_N | 0.327 | – | – |
SNS_VDDQS3_DDR_P | 0.327 | – | – |
SNS1_ALERT_L | 0.749 | – | – |
SPARE_GATE | OL | – | – |
SPI_ALT_CLK | 0.613 | – | – |
SPI_ALT_CS_L | 0.582 | – | – |
SPI_ALT_MISO | 0.518 | – | – |
SPI_ALT_MOSI | 0.583 | – | – |
SPI_CLK | 0.569 | – | – |
SPI_CLK_R | 0.555 | – | – |
SPI_CS0_L | 0.537 | – | – |
SPI_CS0_R_L | 0.524 | – | – |
SPI_DESCRIPTOR_OVERRIDE_L | 0.749 | – | – |
SPI_DESCRIPTOR_OVERRIDE_R | 0.753 | – | – |
SPI_MISO | 0.492 | – | – |
SPI_MLB_CLK | 0.608 | – | – |
SPI_MLB_CS_L | 0.579 | – | – |
SPI_MLB_MISO | 0.504 | – | – |
SPI_MLB_MOSI | 0.548 | – | – |
SPI_MOSI | 0.538 | – | – |
SPI_MOSI_R | 0.532 | – | – |
SPI_SMC_CS_L | 0.592 | – | – |
SPI_SMC_MISO | 0.526 | – | – |
SPI_SMC_MOSI | 0.593 | – | – |
SPI_WP_L | 0.704 | – | – |
SPIROM_USE_MLB | 0.618 | – | – |
SPKR_MATCH_DRV | 0.740 | – | – |
SPKR_MATCH_DRV_R | 0.740 | – | – |
SSD_CLKREQ_L | 0.510 | – | – |
SSD_D2R_N<0> | 0.372 | – | – |
SSD_D2R_N<1> | 0.370 | – | – |
SSD_D2R_P<0> | 0.374 | – | – |
SSD_D2R_P<1> | 0.373 | – | – |
SSD_EN | 0.463 | – | – |
SSD_R2D_C_N<0> | OL | – | – |
SSD_R2D_C_N<1> | OL | – | – |
SSD_R2D_C_P<0> | OL | – | – |
SSD_R2D_C_P<1> | OL | – | – |
SSD_R2D_N<0> | 0.389 | – | – |
SSD_R2D_N<1> | 0.388 | – | – |
SSD_R2D_P<0> | 0.385 | – | – |
SSD_R2D_P<1> | 0.385 | – | – |
SSD_RESET_L | 0.587 | – | – |
SYSCLK_CLK25M_ENET | 0.478 | – | – |
SYSCLK_CLK25M_ENET_R | 0.447 | – | – |
SYSCLK_CLK25M_SB | 0.431 | – | – |
SYSCLK_CLK25M_SB_R | 0.560 | – | – |
SYSCLK_CLK25M_TBT | 0.433 | – | – |
SYSCLK_CLK25M_TBT_R | 0.669 | – | – |
SYSCLK_CLK25M_X1 | 0.442 | – | – |
SYSCLK_CLK25M_X2 | 0.445 | – | – |
SYSCLK_CLK25M_X2_R | 0.444 | – | – |
TBT_A_BIAS | 0.769 | – | – |
TBT_A_CIO_SEL | 0.569 | – | – |
TBT_A_CONFIG1_RC | 0.840 | – | – |
TBT_A_CONFIG2_RC | 0.569 | – | – |
TBT_A_D2R_C_N<0> | 1.566 | – | – |
TBT_A_D2R_C_N<1> | OL | – | – |
TBT_A_D2R_C_P<0> | 1.825 | – | – |
TBT_A_D2R_C_P<1> | OL | – | – |
TBT_A_D2R_N<0> | 0.388 | – | – |
TBT_A_D2R_N<1> | 0.387 | – | – |
TBT_A_D2R_P<0> | 0.388 | – | – |
TBT_A_D2R_P<1> | 0.388 | – | – |
TBT_A_D2R1_AUXDDC_N | 0.701 | – | – |
TBT_A_D2R1_AUXDDC_P | 0.692 | – | – |
TBT_A_DP_PWRDN | 0.616 | – | – |
TBT_A_HPD | 0.840 | – | – |
TBT_A_HV_EN | 0.474 | – | – |
TBT_A_LSRX | 0.575 | – | – |
TBT_A_LSRX_UNBUF | 0.686 | – | – |
TBT_A_LSTX | 0.588 | – | – |
TBT_A_R2D_C_N<0> | 0.222 | – | – |
TBT_A_R2D_C_N<1> | 0.215 | – | – |
TBT_A_R2D_C_P<0> | 0.223 | – | – |
TBT_A_R2D_C_P<1> | 0.175 | – | – |
TBT_A_R2D_N<0> | OL | – | – |
TBT_A_R2D_N<1> | OL | – | – |
TBT_A_R2D_P<0> | OL | – | – |
TBT_A_R2D_P<1> | OL | – | – |
TBT_B_BIAS | 0.769 | – | – |
TBT_B_CONFIG1_BUF | 0.570 | – | – |
TBT_B_CONFIG1_RC | 0.841 | – | – |
TBT_B_CONFIG2_RC | 0.569 | – | – |
TBT_B_D2R_C_N<0> | 1.563 | – | – |
TBT_B_D2R_C_N<1> | OL | – | – |
TBT_B_D2R_C_P<0> | 1.827 | – | – |
TBT_B_D2R_C_P<1> | OL | – | – |
TBT_B_D2R_N<0> | 0.388 | – | – |
TBT_B_D2R_N<1> | 0.389 | – | – |
TBT_B_D2R_P<0> | 0.388 | – | – |
TBT_B_D2R_P<1> | 0.389 | – | – |
TBT_B_D2R1_AUXDDC_N | 0.702 | – | – |
TBT_B_D2R1_AUXDDC_P | 0.689 | – | – |
TBT_B_DP_PWRDN | 0.616 | – | – |
TBT_B_HPD | 0.840 | – | – |
TBT_B_HV_EN | 0.475 | – | – |
TBT_B_LSRX | 0.568 | – | – |
TBT_B_LSRX_UNBUF | 0.683 | – | – |
TBT_B_R2D_C_N<0> | 0.222 | – | – |
TBT_B_R2D_C_N<1> | 0.223 | – | – |
TBT_B_R2D_C_P<0> | 0.223 | – | – |
TBT_B_R2D_C_P<1> | 0.223 | – | – |
TBT_B_R2D_N<0> | OL | – | – |
TBT_B_R2D_N<1> | OL | – | – |
TBT_B_R2D_P<0> | OL | – | – |
TBT_B_R2D_P<1> | OL | – | – |
TBT_CIO_PLUG_EVENT | 0.563 | – | – |
TBT_CIO_PLUG_EVENT_BUF | 0.676 | – | – |
TBT_CIO_PLUG_EVENT_ISOL | 0.500 | – | – |
TBT_CLKREQ_ISOL_L | 0.460 | – | – |
TBT_CLKREQ_L | 0.432 | – | – |
TBT_DDC_XBAR_EN_L | 0.496 | – | – |
TBT_EN_CIO_PWR | 0.380 | – | – |
TBT_EN_CIO_PWR_L | 0.543 | – | – |
TBT_EN_LC_ISOL | 0.457 | – | – |
TBT_EN_LC_PWR | 0.567 | – | – |
TBT_EN_LC_RC1V05 | 0.458 | – | – |
TBT_GO2SX_BIDIR | 0.508 | – | – |
TBT_GPIO_9 | 0.506 | – | – |
TBT_GPIO_14 | 0.559 | – | – |
TBT_MONOBSN | 0.174 | – | – |
TBT_MONOBSP | 0.180 | – | – |
TBT_PCIE_RESET_L | 0.457 | – | – |
TBT_PLT_RST_L | 0.422 | – | – |
TBT_PWR_EN_PCH | 0.550 | – | – |
TBT_PWR_ON_POC_RST_L | 0.575 | – | – |
TBT_RBIAS | 0.792 | – | – |
TBT_RSENSE | 0.000 | – | – |
TBT_SPI_CLK | 0.575 | – | – |
TBT_SPI_CS_L | 0.671 | – | – |
TBT_SPI_MISO | 0.645 | – | – |
TBT_SW_RESET_L | 0.620 | – | – |
TBT_TEST_EN | 0.000 | – | 0.900R |
TBT_TEST_PWR_GOOD | 0.000 | – | – |
TBT_TMU_CLK_IN | 0.651 | – | – |
TBT_TMU_CLK_OUT | 0.556 | – | – |
TBTACONN_1_C | OL | – | – |
TBTACONN_7_C | OL | – | – |
TBTACONN_20_RC | 0.570 | – | – |
TBTAPWRSW_ISET_S0 | 0.483 | – | – |
TBTAPWRSW_ISET_S0_R | OL | – | – |
TBTAPWRSW_ISET_S3 | 0.484 | – | – |
TBTAPWRSW_ISET_S3_R | OL | – | – |
TBTAPWRSW_ISET_V3P3 | 0.454 | – | – |
TBTBCONN_1_C | OL | – | – |
TBTBCONN_7_C | OL | – | – |
TBTBCONN_20_RC | 0.571 | – | – |
TBTBPWRSW_ISET_S0 | 0.483 | – | – |
TBTBPWRSW_ISET_S0_R | OL | – | – |
TBTBPWRSW_ISET_S3 | 0.483 | – | – |
TBTBPWRSW_ISET_S3_R | OL | – | – |
TBTBPWRSW_ISET_V3P3 | 0.485 | – | – |
TBTPOCRST_CT | 0.643 | – | – |
TBTPOCRST_MR_L | 0.634 | – | – |
TBTROM_HOLD_L | 0.738 | – | – |
TBTROM_WP_L | 0.733 | – | – |
TMP006_DRDY | OL | – | – |
TP_CLINK_CLK | 0.539 | – | – |
TP_CLINK_DATA | 0.549 | – | – |
TP_CLINK_RESET_L | 0.602 | – | – |
TP_CPU_FC_VCCST | OL | – | – |
TP_CPU_FC_VCCST_PWRGD | OL | – | – |
TP_CPU_IVR_ERROR | 0.220 | – | – |
TP_CPU_RSVD_TP1 | 0.260 | – | – |
TP_CPU_RSVD_TP2 | 0.260 | – | – |
TP_CPU_RSVD_TP3 | 0.253 | – | – |
TP_CPU_RSVD_TP17 | 0.494 | – | – |
TP_CPU_RSVD_TP25 | 0.255 | – | – |
TP_CPU_RSVD_TP26 | 0.261 | – | – |
TP_CPU_RSVD_TP78 | 0.225 | – | – |
TP_DMIC_SDA2 | 0.710 | – | – |
TP_PCH_SLP_WLAN_L | 0.472 | – | – |
TP_PCH_STRP_ESI_L | 0.661 | – | – |
TP_PCI_PME_L | 0.518 | – | – |
TP_PM_SLP_A_L | 0.663 | – | – |
USB_BT_MUX_N | 0.786 | – | – |
USB_BT_MUX_P | 0.785 | – | – |
USB_BT_N | 0.454 | – | – |
USB_BT_P | 0.460 | – | – |
USB_BT_WAKEN | 0.788 | – | – |
USB_EXTA_0_N | 0.443 | – | – |
USB_EXTA_0_P | 0.442 | – | – |
USB_EXTA_OC_L | 0.475 | – | – |
USB_EXTB_8_N | 0.446 | – | – |
USB_EXTB_8_P | 0.441 | – | – |
USB_EXTB_OC_L | 0.470 | – | – |
USB_EXTC_1_N | 0.442 | – | – |
USB_EXTC_1_P | 0.440 | – | – |
USB_EXTC_OC_L | 0.473 | – | – |
USB_EXTD_9_N | 0.441 | – | – |
USB_EXTD_9_P | 0.443 | – | – |
USB_EXTD_OC_L | 0.471 | – | – |
USB_ILIM1 | 0.531 | – | – |
USB_ILIM1_R | OL | – | – |
USB_ILIM2 | 0.528 | – | – |
USB_ILIM2_R | OL | – | – |
USB2_EXTA_MUXED_N | 0.659 | – | – |
USB2_EXTA_MUXED_P | 0.657 | – | – |
USB2_EXTA_N | 0.663 | – | – |
USB2_EXTA_P | 0.661 | – | – |
USB2_EXTB_N | 0.449 | – | – |
USB2_EXTB_P | 0.445 | – | – |
USB2_EXTC_N | 0.446 | – | – |
USB2_EXTC_P | 0.443 | – | – |
USB2_EXTD_N | 0.445 | – | – |
USB2_EXTD_P | 0.446 | – | – |
USB3_EXTA_RX_F_N | 0.372 | – | – |
USB3_EXTA_RX_F_P | 0.372 | – | – |
USB3_EXTA_RX_N | 0.372 | – | – |
USB3_EXTA_RX_P | 0.372 | – | – |
USB3_EXTA_TX_C_N | OL | – | – |
USB3_EXTA_TX_C_P | OL | – | – |
USB3_EXTA_TX_F_N | OL | – | – |
USB3_EXTA_TX_F_P | OL | – | – |
USB3_EXTB_RX_F_N | 0.389 | – | – |
USB3_EXTB_RX_F_P | 0.389 | – | – |
USB3_EXTB_RX_N | 0.389 | – | – |
USB3_EXTB_RX_P | 0.389 | – | – |
USB3_EXTB_TX_C_N | OL | – | – |
USB3_EXTB_TX_C_P | OL | – | – |
USB3_EXTB_TX_F_N | OL | – | – |
USB3_EXTB_TX_F_P | OL | – | – |
USB3_EXTC_RX_F_N | 0.375 | – | – |
USB3_EXTC_RX_F_P | 0.375 | – | – |
USB3_EXTC_RX_N | 0.375 | – | – |
USB3_EXTC_RX_P | 0.375 | – | – |
USB3_EXTC_TX_C_N | OL | – | – |
USB3_EXTC_TX_C_P | OL | – | – |
USB3_EXTC_TX_F_N | OL | – | – |
USB3_EXTC_TX_F_P | OL | – | – |
USB3_EXTC_TX_N | 0.393 | – | – |
USB3_EXTD_RX_F_N | 0.371 | – | – |
USB3_EXTD_RX_F_P | 0.371 | – | – |
USB3_EXTD_RX_N | 0.371 | – | – |
USB3_EXTD_RX_P | 0.371 | – | – |
USB3_EXTD_TX_C_N | OL | – | – |
USB3_EXTD_TX_C_P | OL | – | – |
USB3_EXTD_TX_F_N | OL | – | – |
USB3_EXTD_TX_F_P | OL | – | – |
USB3_EXTD_TX_P | 0.386 | – | – |
VBIAS_DAC | 0.745 | – | – |
VIDEO_ON | 0.807 | – | – |
VIDEO_ON_L | 0.779 | – | – |
VIDEO_ON_L_DLY | 0.800 | – | – |
VREFMRGN_CA_A_EN | OL | – | – |
VREFMRGN_CA_A_EN_RC | OL | – | – |
VREFMRGN_CA_A_RDIV | OL | – | – |
VREFMRGN_CA_AB | OL | – | – |
VREFMRGN_CA_B_EN | OL | – | – |
VREFMRGN_CA_B_EN_RC | OL | – | – |
VREFMRGN_CA_B_RDIV | OL | – | – |
VREFMRGN_DQ_A | OL | – | – |
VREFMRGN_DQ_A_EN | OL | – | – |
VREFMRGN_DQ_A_EN_RC | OL | – | – |
VREFMRGN_DQ_A_RDIV | OL | – | – |
VREFMRGN_DQ_B | OL | – | – |
VREFMRGN_DQ_B_EN | OL | – | – |
VREFMRGN_DQ_B_EN_RC | OL | – | – |
VREFMRGN_DQ_B_RDIV | OL | – | – |
VREFMRGN_FRAMEBUF_BUF | OL | – | – |
VREFMRGN_FRAMEBUF_EN | OL | – | – |
VREFMRGN_MEMVREG_BUF | OL | – | – |
VSNS_CPUVCC | 0.743 | – | – |
VSNS_HDDS0 | 0.000 | – | – |
VSNS_P1V05S0_PCH | 0.740 | – | – |
VSNS_P12VG3H | 0.741 | – | – |
VSNS_PVDDQS0 | 0.741 | – | – |
VTTCLAMP_EN | 0.603 | – | – |
VTTCLAMP_L | 0.564 | – | – |
WOL_EN | 0.589 | – | – |
XDP_BPM_L<2> | 0.226 | – | – |
XDP_BPM_L<3> | 0.225 | – | – |
XDP_BPM_L<4> | 0.224 | – | – |
XDP_BPM_L<5> | 0.222 | – | – |
XDP_BPM_L<6> | 0.222 | – | – |
XDP_BPM_L<7> | 0.225 | – | – |
XDP_CPU_PCH_TCK | 0.735 | – | – |
XDP_CPU_PCH_TMS | 0.716 | – | – |
XDP_CPU_PRESENT_L | 1.210 | – | – |
XDP_CPU_PWRBTN_L | 0.608 | – | – |
XDP_CPU_PWRGD | 1.377 | – | – |
XDP_CPU_TCK | 0.052 | – | 52.500R |
XDP_CPU_TDI | 0.214 | – | – |
XDP_CPU_TDO | 0.130 | – | – |
XDP_CPU_TDO_PCH_TDI | 0.889 | – | – |
XDP_CPU_TMS | 0.212 | – | – |
XDP_CPU_TRST_L | 0.052 | – | 51.200R |
XDP_CPURST_L | 1.390 | – | – |
XDP_DA0_USB_EXTA_OC_L | 0.474 | – | – |
XDP_DA1_USB_EXTC_OC_L | 0.475 | – | – |
XDP_DA2_PCH_GPIO41 | 0.507 | – | – |
XDP_DA3_PCH_GPIO42 | 0.505 | – | – |
XDP_DB0_USB_EXTB_OC_L | 0.469 | – | – |
XDP_DB1_USB_EXTD_OC_L | 0.471 | – | – |
XDP_DB2_PCH_GPIO10 | 0.508 | – | – |
XDP_DB3_SDCONN_STATE_CHANGE_L | 0.434 | – | – |
XDP_DBRESET_L | 0.636 | – | – |
XDP_DC0_DP_AUXCH_ISOL_L | 0.505 | – | – |
XDP_DC1_SATARDRVR_EN | 0.537 | – | – |
XDP_DC2_PCH_GPIO36 | 0.515 | – | – |
XDP_DC3_JTAG_ISP_TCK | 0.494 | – | – |
XDP_DD0_PCH_GPIO16 | 0.541 | – | – |
XDP_DD1_PCH_GPIO49 | 0.551 | – | – |
XDP_DD2_ENET_CLKREQ_L | 0.515 | – | – |
XDP_DD3_AP_CLKREQ_L | 0.442 | – | – |
XDP_FC0_HDD_PWR_EN | 0.528 | – | – |
XDP_PCH_S5_PWRGD | 1.534 | – | – |
XDP_PCH_TCK | 0.053 | – | – |
XDP_PCH_TDI | 0.080 | – | 79.500R |
XDP_PCH_TDO | 0.080 | – | 79.500R |
XDP_PCH_TMS | 0.080 | – | 79.500R |
XDP_PM_PCH_PWROK | 1.503 | – | – |
XDP_VR_READY | 0.953 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PP3V42_G3H read on the 820-3588?
OpenBoardData's known-good values for PP3V42_G3H on the 820-3588: diode 0.321. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP5V_S5 read on the 820-3588?
OpenBoardData's known-good values for PP5V_S5 on the 820-3588: diode 0.458. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S5 read on the 820-3588?
OpenBoardData's known-good values for PP3V3_S5 on the 820-3588: diode 0.141. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-3588 board?
Open your own 820-3588 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License