Apple laptop board · OpenBoardData

820-3547 known-good readings

Known-good readings for the Apple laptop board 820-3547: 128 nets, including 14 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 14 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3547.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 14 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

S4 2

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.400––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is the 3.3 V rail enabled at the S4 stage of the power sequence, judging from its name. The archive lists a known-good diode reading of 0.400 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S4 to ground and compare with 0.400. Then apply power and check for 3.3 V at the rail. A diode reading far from 0.400 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP5V_S40.498––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail from the S4 startup stage, both from its name. The only known-good reading here is a diode value of 0.498 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from PP5V_S4 to ground, then measure the voltage with power applied. A diode reading far from 0.498 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

S3: memory 3

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S3_SD_DVDD120.300––
AI: what PP1V2_S3_SD_DVDD12 is and how to check it

PP1V2_S3_SD_DVDD12 is a 1.2 V rail; the S3 in its name marks it as a memory-stage supply, and DVDD12 suggests a 1.2 V digital core supply (this is from the name, not from board data). The only known-good figure here is a diode reading of 0.300 to ground, with no condition noted, and there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage at the rail. A diode reading far from 0.300 usually points to a short or a leaky load on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S3_RTUSB_B_F0.490––
AI: what PP5V_S3_RTUSB_B_F is and how to check it

PP5V_S3_RTUSB_B_F is a 5 V rail enabled in the S3 (memory/suspend-to-RAM) stage, judged from its name; the RTUSB_B_F suffix suggests it feeds USB-B circuitry, though that's inference, not board data. Known-good: diode 0.490 in diode mode to ground, with no condition recorded. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S3. No known-good voltage reading here, so compare against a known-good board or the matching rail on the other channel. A diode reading far from 0.490 usually points to a short or leaky part on that rail, but one reading isn't proof — confirm before replacing anything.

PP5V_S3_RTUSB_B_ILIM0.490––
AI: what PP5V_S3_RTUSB_B_ILIM is and how to check it
  • What it is: From its name, PP5V_S3_RTUSB_B_ILIM is a 5 V S3 (memory/suspend-to-RAM) rail tied to a USB current-limit (ILIM) function. The board data doesn't say which parts sit on it.
  • Known-good reading: diode 0.490 to ground. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the rail voltage.
  • If far off: a diode reading well below 0.490 usually points to a short or leaky part on the rail; a high or open reading points to a broken connection. Confirm with a second measurement before replacing anything.

S0: running 9

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V2_S0_SD_AVDD120.295––
AI: what PP1V2_S0_SD_AVDD12 is and how to check it

PP1V2_S0_SD_AVDD12 is a 1.2 V rail; the S0 in the name (from the name) marks it as a running-state supply, and AVDD12 suggests an analog 1.2 V supply, likely in the SD area. The only known-good figure here is a diode reading of 0.295 to ground, with no condition recorded. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with the board powered and running. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from 0.295 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PP1V2_S0_SD_VUHS10.420––
AI: what PP1V2_S0_SD_VUHS1 is and how to check it
  • What it is: From the name, PP1V2_S0_SD_VUHS1 is a 1.2 V rail (PP1V2) that is on in the S0 running state and feeds the SD card interface's UHS-I signalling (SD_VUHS1). The exact parts on it aren't known here.
  • Known-good reading: diode 0.420 to ground, from the readings archive. This is a community guide and varies with board state; no known-good voltage reading is available here.
  • How to check: Power off, then measure diode mode from the rail to ground and compare with 0.420. Then power on and measure the voltage, expecting about 1.2 V when the board is running.
  • If it's far off: a much lower diode reading suggests a short or a failed part on the rail; a missing voltage with a normal diode reading points to the rail not being enabled or its supply not coming up. Confirm with a second measurement before replacing anything.
PP1V05_S0_LDOOL––
AI: what PP1V05_S0_LDO is and how to check it

PP1V05_S0_LDO is a 1.05 V rail, and the S0 in its name marks it as a running-state rail. The only archived reading here is a diode-mode value of OL to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in its running state. An OL diode reading can be normal on some rails, so compare against a matching rail or a known-good board before judging it; a voltage far off 1.05 V usually points to the rail not coming up or being loaded down, but that is a likely cause, not a confirmed one.

PP1V5_S0_P1V05_LDOOL––
AI: what PP1V5_S0_P1V05_LDO is and how to check it

PP1V5_S0_P1V05_LDO is a 1.5 V rail that is active in the S0 (running) state, judged from its name; the "P1V05_LDO" part suggests it is derived from a 1.05 V LDO supply, though that is general reading of the name, not board data. The only archived reading for this net is a diode value of OL, with no condition recorded. To check it, power the board off and measure diode mode from the net to ground, then measure the voltage on the net with the board powered in S0. A diode reading far from OL (a low value) usually points to a short or a leaky part on the rail, but with no known-good voltage reading here, compare against a matching rail or a known-good board before condemning anything.

PP3V3_S0_P1V05_LDO_BIASOL––
AI: what PP3V3_S0_P1V05_LDO_BIAS is and how to check it
  • What it is: From the name, PP3V3_S0_P1V05_LDO_BIAS is a 3.3 V rail that is on in the S0 (running) state and feeds the bias input of a 1.05 V LDO. That's inferred from the name only; the parts on the net aren't known here.
  • Known-good reading: the archive gives diode OL to ground. No known-good voltage reading is recorded for this rail.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with that OL; then power up and measure the voltage in S0.
  • If it's far off: a low diode reading or a sagging voltage usually points to a short or a heavy load on the rail, but a single reading doesn't confirm a bad part.
PP3V3_S0_SD_AVDD330.404––
AI: what PP3V3_S0_SD_AVDD33 is and how to check it

PP3V3_S0_SD_AVDD33 is a 3.3 V rail (from the name), and the S0 in the name marks it as a running-state rail, so it should be present once the board is fully on. The archive lists one known-good diode reading of 0.404 to ground; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage, expecting about 3.3 V. A diode reading far from 0.404 suggests a short or leaky part on the rail, but one reading isn't proof; compare with a matching rail or a known-good board before replacing anything.

PP3V3_S0_SD_CONN0.415––
AI: what PP3V3_S0_SD_CONN is and how to check it

PP3V3_S0_SD_CONN is a 3.3 V rail that, from its name, supplies the SD connector and is active in the S0 (running) state. The only known-good reading here is a diode value of 0.415 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.415.
  • Then power the board and measure the voltage on the rail; it should be near 3.3 V once the board is in S0.

A diode reading far below 0.415 usually points to a short or a leaky part on the rail, while a much higher reading can mean an open connection. These are general guidelines, not confirmed values for this board.

PP3V3_S0SW_SD0.412––
AI: what PP3V3_S0SW_SD is and how to check it

PP3V3_S0SW_SD is a 3.3 V rail, from its name: a switched (SW) supply active in the S0 running state, likely feeding the SD card circuit. The only known-good figure here is a diode reading of 0.412 to ground, with the board unpowered; there is no known-good voltage reading for this rail. Check it in diode mode to ground first, then power the board and measure the voltage at the rail. A diode reading far from 0.412 usually points to a short or a leaky part on the rail, but confirm with a voltage measurement before replacing anything.

PP5V_HDMI_DDC_S00.541––
AI: what PP5V_HDMI_DDC_S0 is and how to check it

PP5V_HDMI_DDC_S0 is the 5 V HDMI DDC rail, and the S0 suffix means it is present in the running state (both from the name). The archive lists one known-good diode reading of 0.541 to ground; there is no known-good voltage reading here. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and running. A diode reading far from 0.541 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

Every net with a reading

NetDiodeVoltageResistance
EQ_I2C_ADDR00.484––
HDMI_3V3_PWR_EN0.535––
HDMI_CLK_C_LS_NOL––
HDMI_CLK_C_LS_POL––
HDMI_CLK_CONN_N0.460––
HDMI_CLK_CONN_P0.460––
HDMI_CLK_LS_N0.670––
HDMI_CLK_LS_P0.642––
HDMI_CLK_N0.458––
HDMI_CLK_P0.458––
HDMI_DATA_C_N<0>OL––
HDMI_DATA_C_P<0>OL––
HDMI_DATA_CONN_N<0>0.457––
HDMI_DATA_CONN_N<1>0.457––
HDMI_DATA_CONN_N<2>0.458––
HDMI_DATA_CONN_P<0>0.457––
HDMI_DATA_CONN_P<1>0.457––
HDMI_DATA_CONN_P<2>0.458––
HDMI_DATA_LS_N<0>0.670––
HDMI_DATA_LS_N<1>0.670––
HDMI_DATA_LS_N<2>0.670––
HDMI_DATA_LS_P<0>0.645––
HDMI_DATA_LS_P<1>0.640––
HDMI_DATA_LS_P<2>0.641––
HDMI_DATA_N<0>0.455––
HDMI_DATA_N<1>0.455––
HDMI_DATA_N<2>0.456––
HDMI_DATA_P<0>0.456––
HDMI_DATA_P<1>0.455––
HDMI_DATA_P<2>0.456––
HDMI_DDC_CLK_5V0.577––
HDMI_DDC_CLK_CONN0.600––
HDMI_DDC_CLK_F0.593––
HDMI_DDC_DATA_5V0.576––
HDMI_DDC_DATA_CONN0.600––
HDMI_DDC_LS_CLK0.461––
HDMI_DDC_LS_DATA0.459––
HDMI_HPD_CONN0.664––
HDMI_HPD_F0.654––
HDMI_HPD_LS0.480––
HDMI_HPD_R0.480––
HDMI_HPD_SINK0.491––
HDMI_HPD_SNK_R0.490––
HDMI_MIDOL––
HDMI_OC_L0.537––
I2C_HDMIRDRV_SCL_CONN0.482––
I2C_HDMIRDRV_SDA_CONN0.482––
LS_CFG_I2C_ADDR10.537––
LS_I2C_CTL_EN0.546––
LS_ISET0.543––
LS_PWR_DWN_L0.490––
P1V05S0_LDO_PGOODOL––
PM_SLP_S3_L0.529––
PM_SLP_S4_L0.493––
PP1V2_S0_SD_AVDD120.295––
PP1V2_S0_SD_VUHS10.420––
PP1V2_S3_SD_DVDD120.300––
PP1V5_HDMI_VDDRX0.252––
PP1V5_HDMI_VDDTA0.248––
PP1V5_HDMI_VDDTX0.251––
PP1V05_S0_LDOOL––
PP1V5_S0_P1V05_LDOOL––
PP1V5R1V05_HDMI_VDD0.258––
PP3V3_HDMI0.432––
PP3V3_HDMI_VDD33_FLTR0.432––
PP3V3_S0_P1V05_LDO_BIASOL––
PP3V3_S0_SD_AVDD330.404––
PP3V3_S0_SD_CONN0.415––
PP3V3_S0SW_SD0.412––
PP3V3_S40.400––
PP5V_HDMI_DDC_CONN0.541––
PP5V_HDMI_DDC_FUSE0.535––
PP5V_HDMI_DDC_S00.541––
PP5V_S3_RTUSB_B_F0.490––
PP5V_S3_RTUSB_B_ILIM0.490––
PP5V_S40.498––
PREQ0.540––
REXT_LS0.477––
SD_DETECT_L0.463––
SD_PWR_EN0.572––
SD_RESET_L0.688––
SD_RTERM0.669––
SD_SPI_CLK0.580––
SD_SPI_CS_L0.718––
SD_SPI_MISO0.717––
SD_SPI_MOSI0.718––
SD_SPI_WP_LOL––
SDCLK_CLK25M_X20.585––
SDCLK_CLK25M_X2_R0.584––
SDCONN_CLK0.465––
SDCONN_CLK_FLT0.498––
SDCONN_CLK_R0.497––
SDCONN_CLK_R_L0.493––
SDCONN_CMD0.460––
SDCONN_CMD_R0.492––
SDCONN_DATA<0>0.464––
SDCONN_DATA<1>0.463––
SDCONN_DATA<2>0.498––
SDCONN_DATA<3>0.464––
SDCONN_DATA<4>OL––
SDCONN_DATA<5>OL––
SDCONN_DATA<6>OL––
SDCONN_DATA<7>OL––
SDCONN_DETECT_L0.472––
SDCONN_DETECT_L_R0.474––
SDCONN_R_DATA<0>0.497––
SDCONN_R_DATA<2>0.498––
SDCONN_R_DATA<3>0.498––
SDCONN_STATE_CHANGE0.436––
SDCONN_WP0.708––
SDSCLK_CLK25M_X10.520––
TP_HDMI_CEC_CONNOL––
TPS2553_EN0.529––
TPS2553_ILIM0.560––
USB_EXTB_F_NOL––
USB_EXTB_F_POL––
USB_EXTB_NOL––
USB_EXTB_OC_L0.523––
USB_EXTB_POL––
USB_ILIM0.521––
USB_MIDOL––
USB_PWR_EN0.488––
USB_SD_DM0.729––
USB_SD_DP0.729––
USB3_SD_D2R_C_N0.352––
USB3_SD_D2R_C_P0.362––
USB3_SD_R2D_C_N0.364––
USB3_SD_R2D_C_P0.365––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP5V_S4 read on the 820-3547?

OpenBoardData's known-good values for PP5V_S4 on the 820-3547: diode 0.498. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3547 board?

Open your own 820-3547 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License