Apple laptop board · OpenBoardData
820-3539 known-good readings
Known-good readings for the Apple laptop board 820-3539: 120 nets, including 17 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 17 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-3539.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 17 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
S4 2
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S4 | 0.362 | – | – |
AI: what PP3V3_S4 is and how to check itPP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging by its name; the board data doesn't list which parts sit on it. The only known-good reading here is a diode value of 0.362 to ground, with no condition given, and there is no known-good voltage reading. Check it unpowered in diode mode from PP3V3_S4 to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.362 suggests a short or leaky part on the rail, but a small difference can be normal, so compare with a matching net or a known-good board before replacing anything. | |||
PP5V_S4 | 0.495 | – | – |
AI: what PP5V_S4 is and how to check it
| |||
S3: memory 3
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S3_SD_DVDD12 | 0.280 | – | – |
AI: what PP1V2_S3_SD_DVDD12 is and how to check it
| |||
PP5V_S3_RTUSB_B_F | 0.494 | – | – |
AI: what PP5V_S3_RTUSB_B_F is and how to check it
| |||
PP5V_S3_RTUSB_B_ILIM | 0.494 | – | – |
AI: what PP5V_S3_RTUSB_B_ILIM is and how to check itPP5V_S3_RTUSB_B_ILIM is a 5 V rail that, from its name, belongs to the S3 (memory) startup stage and appears to be a current-limit reference for a USB path (the "ILIM" part is from the name, not confirmed by data). The only known-good reading here is a diode value of 0.494; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on it. A diode reading far from 0.494 usually points to a short or a leaky component on that net, but a single reading isn't proof a part is bad. | |||
S0: running 12
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP1V2_S0_SD_AVDD12 | 0.280 | – | – |
AI: what PP1V2_S0_SD_AVDD12 is and how to check itPP1V2_S0_SD_AVDD12 is a 1.2 V rail; the S0 in the name indicates it belongs to the running state, and AVDD12 suggests an analog 1.2 V supply, though that part is inference from the name rather than board data.
| |||
PP1V2_S0_SD_VUHS1 | 0.425 | – | – |
AI: what PP1V2_S0_SD_VUHS1 is and how to check itPP1V2_S0_SD_VUHS1 — from the name, a 1.2 V rail (PP1V2) that is on in the S0 running state and feeds the SD card interface's VUHS1 supply. The only known-good figure in the readings archive is a diode reading of 0.425 to ground; there is no known-good voltage reading here.
| |||
PP1V5_S0 | 0.254 | – | – |
AI: what PP1V5_S0 is and how to check itPP1V5_S0 is a 1.5 V rail; the S0 suffix, from its name, marks it as a running-state supply. The archive lists one known-good diode reading of 0.254 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.254 usually points to a short or a leaky load on the rail, but a single reading isn't proof a part is bad. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. | |||
PP1V05_S0_LDO | OL | – | – |
AI: what PP1V05_S0_LDO is and how to check it
| |||
PP1V5_S0_P1V05_LDO | OL | – | – |
AI: what PP1V5_S0_P1V05_LDO is and how to check itPP1V5_S0_P1V05_LDO is a 1.5 V rail that is active in S0 (running), judged from its name; the P1V05_LDO part suggests it also feeds a 1.05 V LDO input. The only archived reading is a diode-mode value of OL to ground, with no condition recorded and no known-good voltage here. Check it unpowered in diode mode from the rail to ground, then with power applied measure the voltage at the rail. A diode reading far from OL, or a voltage well off 1.5 V, usually points to a short or a failed source, but one reading alone doesn't confirm a bad part. | |||
PP3V3_S0 | 0.428 | – | – |
AI: what PP3V3_S0 is and how to check itPP3V3_S0 is a 3.3 V supply rail; the "S0" suffix, from its name, marks it as a running-state rail (active once the board is in its normal on state). The only known-good reading here is a diode value of 0.428 to ground, with no condition recorded; there is no known-good voltage reading in this data.
A diode reading far below 0.428 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken connection. Treat these as guides, not confirmed faults, and confirm with a voltage measurement before replacing anything. | |||
PP3V3_S0_P1V05_LDO_BIAS | OL | – | – |
AI: what PP3V3_S0_P1V05_LDO_BIAS is and how to check itPP3V3_S0_P1V05_LDO_BIAS is a 3.3 V rail that, from its name, is tied to an S0 (running) state and to a 1.05 V LDO bias supply. The only known-good reading in the archive is a diode reading of OL to ground, so treat that as a guide rather than a fixed value. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on it with power applied and the board in S0. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far from OL (a low value) usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a bad part. | |||
PP3V3_S0_SD_AVDD33 | 0.408 | – | – |
AI: what PP3V3_S0_SD_AVDD33 is and how to check it
| |||
PP3V3_S0_SD_CONN | 0.413 | – | – |
AI: what PP3V3_S0_SD_CONN is and how to check itPP3V3_S0_SD_CONN is a 3.3 V rail, from its name: the S0 state means it's present while the board is running, and SD_CONN suggests it feeds the SD card connector. The only known-good reading here is a diode value of 0.413 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.413 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything. | |||
PP3V3_S0SW_SD | 0.408 | – | – |
AI: what PP3V3_S0SW_SD is and how to check itPP3V3_S0SW_SD is a 3.3 V rail that is switched and enabled in the S0 (running) state, judging from its name. It appears to feed SD card power, again from the name only.
| |||
PP5V_HDMI_DDC_S0 | 0.536 | – | – |
AI: what PP5V_HDMI_DDC_S0 is and how to check itPP5V_HDMI_DDC_S0 is a 5 V HDMI DDC rail, and the S0 suffix indicates it is present in the running state (from the name). The archive lists one known-good reading: diode 0.536 to ground, with no condition noted. Check it unpowered in diode mode from the net to ground, then measure the voltage with the board running. No known-good voltage reading here, so compare against a matching HDMI DDC rail or a known-good board. A diode reading far below 0.536 usually points to a short or leaky part on the rail; far above it suggests an open path, but confirm with the voltage before replacing anything. | |||
PP5V_HDMI_DDC_S0_F | 0.534 | – | – |
AI: what PP5V_HDMI_DDC_S0_F is and how to check it
| |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
DPMUX_ROM_WC_L | 0.601 | – | – |
ENABLE_HDMI_DDC_S0 | OL | – | – |
ENABLE_HDMI_DDC_S0_R | OL | – | – |
EQ_I2C_ADDR0 | 0.487 | – | – |
GND | 0.001 | – | – |
HDMI_3V3_PWR_EN | 0.534 | – | – |
HDMI_CLK_LS_N | 0.667 | – | – |
HDMI_CLK_LS_P | 0.648 | – | – |
HDMI_DATA_C_N<0> | OL | – | – |
HDMI_DATA_C_P<0> | OL | – | – |
HDMI_DDC_CLK_5V | 0.577 | – | – |
HDMI_DDC_CLK_CONN | 0.590 | – | – |
HDMI_DDC_CLK_F | 0.592 | – | – |
HDMI_DDC_DATA_5V | 0.577 | – | – |
HDMI_DDC_DATA_CONN | 0.591 | – | – |
HDMI_DDC_DATA_F | 0.591 | – | – |
HDMI_DDC_LS_CLK | 0.497 | – | – |
HDMI_DDC_LS_CLK_R | 0.497 | – | – |
HDMI_DDC_LS_DATA | 0.498 | – | – |
HDMI_DDC_LS_DATA_R | 0.497 | – | – |
HDMI_HPD | 0.485 | – | – |
HDMI_HPD_CONN | 0.649 | – | – |
HDMI_HPD_F | 0.650 | – | – |
HDMI_HPD_R | 0.483 | – | – |
HDMI_HPD_SINK | 0.494 | – | – |
HDMI_HPD_SNK_R | 0.494 | – | – |
HDMI_OC_L | 0.537 | – | – |
I2C_HDMIRDRV_SCL_CONN | 0.490 | – | – |
I2C_HDMIRDRV_SDA_CONN | 0.489 | – | – |
LS_CFG_I2C_ADDR1 | 0.001 | – | – |
LS_I2C_CTL_EN | 0.548 | – | – |
LS_ISET | 0.549 | – | – |
LS_PWR_DWN_L | 0.498 | – | – |
P1V05S0_LDO_FB | OL | – | – |
P1V5S0_LDO_PGOOD | OL | – | – |
P1V05S0_LDO_SS | OL | – | – |
P3V3_SD_FET_RAMP | 0.702 | – | – |
PCIE_AP_R2D_N | OL | – | – |
PCIE_AP_R2D_P | OL | – | – |
PCIE_CLK100M_AP_N | OL | – | – |
PM_SLP_S3_L | 0.534 | – | – |
PM_SLP_S4_L | 0.490 | – | – |
PP1V2_S0_SD_AVDD12 | 0.280 | – | – |
PP1V2_S0_SD_VUHS1 | 0.425 | – | – |
PP1V2_S3_SD_DVDD12 | 0.280 | – | – |
PP1V5_HDMI_VDDRX | 0.251 | – | – |
PP1V5_HDMI_VDDTA | 0.253 | – | – |
PP1V5_HDMI_VDDTX | 0.251 | – | – |
PP1V5_S0 | 0.254 | – | – |
PP1V05_S0_LDO | OL | – | – |
PP1V5_S0_P1V05_LDO | OL | – | – |
PP1V5R1V05_HDMI_VDD | 0.252 | – | – |
PP3V3_HDMI_VDD33 | 0.429 | – | – |
PP3V3_S0 | 0.428 | – | – |
PP3V3_S0_P1V05_LDO_BIAS | OL | – | – |
PP3V3_S0_SD_AVDD33 | 0.408 | – | – |
PP3V3_S0_SD_CONN | 0.413 | – | – |
PP3V3_S0SW_SD | 0.408 | – | – |
PP3V3_S4 | 0.362 | – | – |
PP5V_HDMI_DDC_CONN | 0.536 | – | – |
PP5V_HDMI_DDC_FUSE | 0.536 | – | – |
PP5V_HDMI_DDC_S0 | 0.536 | – | – |
PP5V_HDMI_DDC_S0_F | 0.534 | – | – |
PP5V_S3_RTUSB_B_F | 0.494 | – | – |
PP5V_S3_RTUSB_B_ILIM | 0.494 | – | – |
PP5V_S4 | 0.495 | – | – |
PREQ | 0.548 | – | – |
REXT_LS | 0.482 | – | – |
SD_DETECT_L | 0.458 | – | – |
SD_PWR_EN | 0.573 | – | – |
SD_RESET_L | OL | – | – |
SD_RESET_R_L | 0.697 | – | – |
SD_RTERM | 0.665 | – | – |
SD_SPI_CLK | 0.710 | – | – |
SD_SPI_CS_L | 0.713 | – | – |
SD_SPI_HOLD_L | OL | – | – |
SD_SPI_MISO | 0.711 | – | – |
SD_SPI_MOSI | 0.710 | – | – |
SD_SPI_WP_L | OL | – | – |
SDCLK_CLK25M_X2 | 0.582 | – | – |
SDCONN_CLK | 0.463 | – | – |
SDCONN_CLK_R | 0.496 | – | – |
SDCONN_CLK_R_L | 0.496 | – | – |
SDCONN_CMD | 0.463 | – | – |
SDCONN_CMD_R | 0.496 | – | – |
SDCONN_DATA<0> | 0.465 | – | – |
SDCONN_DATA<1> | 0.463 | – | – |
SDCONN_DATA<2> | 0.464 | – | – |
SDCONN_DATA<3> | 0.464 | – | – |
SDCONN_DETECT_L | 0.464 | – | – |
SDCONN_DETECT_L_R | 0.464 | – | – |
SDCONN_R_DATA<0> | 0.496 | – | – |
SDCONN_R_DATA<1> | 0.496 | – | – |
SDCONN_R_DATA<2> | 0.497 | – | – |
SDCONN_R_DATA<3> | 0.497 | – | – |
SDCONN_R_DATA<6> | OL | – | – |
SDCONN_R_DATA<7> | 0.001 | – | – |
SDCONN_WP | 0.701 | – | – |
SDSCLK_CLK25M_X1 | 0.518 | – | – |
TPS2553_EN | 0.534 | – | – |
TPS2553_ILIM | 0.556 | – | – |
TPS2553_ILIM_R | OL | – | – |
USB_EXTB_F_N | OL | – | – |
USB_EXTB_F_P | OL | – | – |
USB_EXTB_N | OL | – | – |
USB_EXTB_OC_L | 0.519 | – | – |
USB_EXTB_P | OL | – | – |
USB_ILIM | 0.524 | – | – |
USB_ILIM_R | OL | – | – |
USB_PWR_EN | 0.490 | – | – |
USB_SD_DM | 0.722 | – | – |
USB_SD_DP | 0.721 | – | – |
USB3_EXTB_R2D_C_N | OL | – | – |
USB3_EXTB_R2D_C_P | OL | – | – |
USB3_EXTB_R2D_N | OL | – | – |
USB3_EXTB_R2D_P | OL | – | – |
USB3_SD_D2R_N | OL | – | – |
USB3_SD_D2R_P | OL | – | – |
USB3_SD_R2D_C_N | OL | – | – |
USB3_SD_R2D_C_P | OL | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PP5V_S4 read on the 820-3539?
OpenBoardData's known-good values for PP5V_S4 on the 820-3539: diode 0.495. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S0 read on the 820-3539?
OpenBoardData's known-good values for PP3V3_S0 on the 820-3539: diode 0.428. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-3539 board?
Open your own 820-3539 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License