Apple desktop board · OpenBoardData

820-3482 known-good readings

Known-good readings for the Apple desktop board 820-3482: 1,902 nets, including 77 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 77 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3482.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 77 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 9

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V2_G3H_SMC_VDDC0.520––
AI: what PP1V2_G3H_SMC_VDDC is and how to check it

PP1V2_G3H_SMC_VDDC is a 1.2 V rail feeding the SMC, and the G3H in its name indicates it is always-on. The archive lists a known-good diode reading of 0.520 to ground; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.520 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_G30.573––
AI: what PP3V3_G3 is and how to check it
  • What it is: PP3V3_G3 is a 3.3 V always-on rail; the "G3" in the name marks it as an always-on (G3H) startup rail, and the 3V3 indicates its nominal 3.3 V level. This is from the name only.
  • Known-good reading: diode 0.573 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_G3 to ground and compare with 0.573; then apply power and measure the rail voltage, expecting about 3.3 V.
  • If it's far off: a diode reading well below known-good often suggests a short or leaky part on the rail, while a missing or low voltage with a normal diode reading points more toward the supply feeding it. These are general guidelines, not confirmed causes.
PP3V3_G3H_AVREF_SMC0.610––
AI: what PP3V3_G3H_AVREF_SMC is and how to check it

PP3V3_G3H_AVREF_SMC is a 3.3 V rail on the 820-3482. From its name it's an always-on (G3H) reference supply for the SMC, and it's an AVREF-type reference, so it's likely a quiet analog reference rather than a heavy load rail.

  • Known-good: diode-to-ground 0.610 in the readings archive. That's a community guide, not a spec, and no known-good voltage reading is recorded here.
  • Check it unpowered in diode mode to ground, then power the board and measure the voltage at the rail.
  • A diode reading far below 0.610 usually points to a short or a leaky part on the rail; a reading far above it can mean an open path or a missing connection. Confirm with a second measurement before replacing anything.
PP3V3_G3H_BT_FLT0.515––
AI: what PP3V3_G3H_BT_FLT is and how to check it

PP3V3_G3H_BT_FLT is a 3.3 V rail; the G3H part of the name indicates it is always on, and the BT_FLT part suggests it feeds Bluetooth circuitry. The only known-good reading here is a diode value of 0.515 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.515 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_G3H_SMC_VDDA0.329––
AI: what PP3V3_G3H_SMC_VDDA is and how to check it

PP3V3_G3H_SMC_VDDA is a 3.3 V always-on rail feeding the SMC's analog supply; the G3H part of the name indicates it is always on, and SMC_VDDA indicates the SMC analog supply (from the name).

  • Known-good: diode reading 0.329 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • A diode reading far from 0.329 usually points to a short or a leaky part on that rail; a missing or low voltage with a normal diode reading points more toward the supply that generates it. These are general guidelines, not confirmed for this board.
PP3V42_G3H0.329––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, indicated by the "G3H" in its name. The archive lists one known-good diode reading of 0.329 to ground; no known-good voltage reading is recorded here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.329.
  • Then power the board and measure the voltage on the rail; it should sit near 3.42 V, though that figure comes from the rail name, not from a recorded reading.
  • A diode reading far from 0.329 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.
PP3V42_G3H_SMC_SPVSR0.375––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is a 3.42 V always-on rail feeding the SMC's SPVSR input, judging from the name (G3H = always on). The archive lists one known-good diode reading of 0.375 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from the net to ground and compare with 0.375, then power up and check the voltage. A diode reading far from 0.375 usually points to a short or a damaged part on that net, but one reading alone doesn't confirm a fault.

PP12V_G3H0.568––
AI: what PP12V_G3H is and how to check it

PP12V_G3H is a 12 V rail; the "G3H" suffix indicates it is always-on, from the name. The archive lists a diode reading of 0.568 to ground for this net; no known-good voltage reading is available here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.568.
  • Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.568 usually suggests a short or a leaky load on the rail; a much higher reading can mean an open trace or missing connection. One reading alone doesn't confirm a bad part, so compare with a matching net or a known-good board before replacing anything.
PPVBATT_G3_RTC_ROL––
AI: what PPVBATT_G3_RTC_R is and how to check it

PPVBATT_G3_RTC_R — the name indicates a battery-backed, always-on rail (G3H) feeding the RTC circuit. The only known-good reading here is a diode value of OL to ground; this is a guide from community readings, and there is no known-good voltage or resistance value for this rail.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. An OL reading matches the known-good value; a low reading suggests a short or a leaky part on the rail.
  • Then check it powered: measure the voltage with the board on and compare it with what the RTC circuit expects. No known-good voltage is listed here, so compare against a matching net or a known-good board.
  • A reading far from OL in diode mode usually points to a shorted or leaky component on that rail, but one reading alone doesn't confirm a bad part.

S5 and SUS: standby 6

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.145––
AI: what PP3V3_S5 is and how to check it
  • What it is: PP3V3_S5 is the 3.3 V standby rail; the "S5" in the name marks it as a standby-stage supply that should be present before the board fully powers on (from the name, not from board data).
  • Known-good reading: diode 0.145 to ground, from the readings archive. This is a community-contributed guide and can vary with board state.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S5 to ground; then apply power and measure the voltage on the rail. No known-good voltage reading is available here.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a much higher one suggests an open path. Confirm with a second measurement before suspecting any part.
PP3V3_S5_XDP_R0.107––
AI: what PP3V3_S5_XDP_R is and how to check it

PP3V3_S5_XDP_R is a 3.3 V standby rail; the "S5" in its name marks it as a standby-stage rail, and "XDP" suggests it feeds a debug or data-port related circuit (that part is general inference, not from board data). The only known-good reading here is a diode value of 0.107 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.107 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.

PP5V_S50.457––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is a 5 V standby rail; the S5/SUS part of the name indicates it belongs to the standby stage, before the main rails come up. The only known-good reading here is a diode value of 0.457 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from PP5V_S5 to ground, then power up and measure the voltage at the rail. A diode reading far from 0.457 suggests a short or leaky load on the rail; a missing or low voltage with a normal diode reading points more toward the standby supply or its enable. These are guides from community readings, not confirmed limits, so compare against a matching net or a known-good board before condemning a part.

PP12V_S50.541––
AI: what PP12V_S5 is and how to check it

PP12V_S5 is a 12 V rail in the S5 standby stage, judged from its name; the archive has no parts list for it. The only known-good reading here is diode mode 0.541 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is recorded. A diode reading far from 0.541 usually points to a short or leak on that rail, but one reading isn't proof, so confirm before replacing anything.

PPVOUT_S5_PCH_DCPSUSBYP0.419––
AI: what PPVOUT_S5_PCH_DCPSUSBYP is and how to check it
  • What it is: From its name, PPVOUT_S5_PCH_DCPSUSBYP is a PCH power rail active in S5 standby (the S5 and SUS parts of the name). The DCPSUSBYP suffix suggests a bypass or decoupling point on that supply; the exact parts on it aren't known here.
  • Known-good reading: diode 0.419 to ground, from the readings archive. This is a community guide, not a factory spec, and no voltage reading is listed.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open trace or missing part. Confirm with a second measurement before replacing anything.
PPVOUT_S5_PCH_DCPSUSBYP_R0.414––
AI: what PPVOUT_S5_PCH_DCPSUSBYP_R is and how to check it
  • What it is: From the name, PPVOUT_S5_PCH_DCPSUSBYP_R is a standby (S5/SUS) output rail feeding the PCH's DC/DC bypass. The exact parts on it aren't known here.
  • Known-good reading: diode 0.414 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a diode reading well below known-good usually points to a shorted load or capacitor on that rail; a high or open reading points to a broken feed. Confirm with voltage before replacing anything.

S4 19

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V2_S4_CAMERA0.337––
AI: what PP1V2_S4_CAMERA is and how to check it

PP1V2_S4_CAMERA is a 1.2 V rail, judging by its name, and the S4 in the name marks it as a startup-stage rail. The only known-good figure here is a diode reading of 0.337 to ground; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then power up and measure the voltage. A diode reading far from 0.337 usually points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PP1V2_S4_CAMFILT0.348––
AI: what PP1V2_S4_CAMFILT is and how to check it

PP1V2_S4_CAMFILT is a 1.2 V rail in the S4 power state, judging by its name; the CAMFILT part suggests it feeds camera filtering, but that's inference from the name, not board data. The only known-good reading here is a diode of 0.348 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode far below 0.348 suggests a short or leaky load on the rail, while a far higher or open reading points to a broken connection; a missing voltage with a normal diode points upstream to the S4 enable and supply. These are community readings and a guide only, so compare against a matching rail or a known-good board before condemning a part.

PP1V2_S4_F_R0.337––
AI: what PP1V2_S4_F_R is and how to check it

PP1V2_S4_F_R is a 1.2 V rail in the S4 startup stage, judging from its name; the "F_R" suffix likely marks a filtered rail, but that part is general interpretation, not board data.

  • Known-good: diode reading 0.337 to ground (community archive, no condition noted). No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • A diode reading far below 0.337 suggests a short or a leaky load on the rail; far above it can mean an open path. Confirm with a second reading before suspecting a part.
PP1V8_S4_CAMERA0.433––
AI: what PP1V8_S4_CAMERA is and how to check it

PP1V8_S4_CAMERA is a 1.8 V rail, judged from its name, and the S4 in the name marks it as a later startup stage. The only known-good figure here is a diode reading of 0.433 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then measure the voltage with power applied. A diode reading far from 0.433 usually points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault, so compare with a matching rail before replacing anything.

PP1V8_S4_CAMERA_F0.433––
AI: what PP1V8_S4_CAMERA_F is and how to check it
  • What it is: PP1V8_S4_CAMERA_F is a 1.8 V rail feeding camera circuitry, judged from the name; the S4 suffix places it in the S4 startup stage. No board file is available, so the parts on this net aren't known.
  • Known-good reading: diode 0.433 to ground, from the readings archive. This is a community value and a guide only; there is no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP1V8_S4_CAMERA_F to ground and compare with 0.433. Then apply power and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail; a much higher one to an open path. A voltage that's missing or wrong with a normal diode reading suggests the rail isn't being enabled or supplied, so check its source next.
PP3V3_S40.332––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail; the "S4" in its name marks it as a later startup-stage rail, not an always-on one. The archive lists one known-good diode reading for it: 0.332 to ground, with no condition noted, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.332 usually points to a short or a leaky part on that rail, but one reading isn't proof. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board.

PP3V3_S4_ALS_F0.332––
AI: what PP3V3_S4_ALS_F is and how to check it
  • What it is: A 3.3 V rail in the S4 power state, from its name; the "ALS" suffix suggests it feeds an ambient light sensor circuit (general interpretation, not from board data).
  • Known-good reading: diode 0.332 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP3V3_S4_ALS_F to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode reading usually points to a short or a failed part on the rail, while a missing voltage with a normal diode reading points upstream to the S4 enable or supply. Readings vary with board state, so treat them as a guide.
PP3V3_S4_AP_FLT0.501––
AI: what PP3V3_S4_AP_FLT is and how to check it

PP3V3_S4_AP_FLT is a 3.3 V rail in the S4 startup stage, from its name; the "FLT" suffix suggests a filtered or fault-related branch, though that part is inference, not board data.

  • Known-good: diode 0.501 to ground, from the readings archive. No known-good voltage reading here.
  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.501.
  • Then power the board and measure the voltage; expect about 3.3 V, but that's general expectation, not a recorded value.

A diode reading far below 0.501 usually points to a short or a leaky part on the rail; far above it suggests an open trace or missing connection. One reading alone doesn't confirm a bad part, so recheck and compare against a matching rail before replacing anything.

PP3V3_S4_CAMFILT0.332––
AI: what PP3V3_S4_CAMFILT is and how to check it

PP3V3_S4_CAMFILT — reference note

  • What it is: a 3.3 V rail at the S4 power state, from its name; the "CAMFILT" suffix suggests it feeds camera circuitry through a filter (general reading of the name, not from board data).
  • Known-good: diode-to-ground 0.332 in the readings archive. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground and compare with 0.332; then power up and measure the voltage at the rail. Community readings vary with board state, so treat them as a guide.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP5V_S40.158––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging by its name; the archive has no board file, so the parts on it aren't known. The only known-good reading here is a diode value of 0.158 to ground. Check it with the board unpowered in diode mode from PP5V_S4 to ground, then power up and measure the voltage on the rail. No known-good voltage reading is recorded here, so compare against a matching S4 rail or a known-good board. A diode reading far from 0.158 usually points to a short or leaky part on the rail, but one reading alone doesn't confirm a fault.

PP5V_S4_CAMERA_F0.156––
AI: what PP5V_S4_CAMERA_F is and how to check it

PP5V_S4_CAMERA_F is a 5 V rail feeding the camera circuit, enabled at the S4 startup stage — both from the name. The archive lists one known-good reading: diode mode to ground 0.156, with no condition noted. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage is present when the board reaches S4. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far below 0.156 usually points to a short or leaky part on the rail; far above suggests an open path — treat either as a lead to trace, not a confirmed fault.

PP5V_S4_EXTA_F0.526––
AI: what PP5V_S4_EXTA_F is and how to check it

PP5V_S4_EXTA_F is a 5 V rail in the S4 startup stage, judging by its name; the archive has no board file, so which parts sit on it isn't known. The only known-good reading is diode 0.526 to ground, with no condition recorded; there is no known-good voltage or resistance value here.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied.
  • A diode reading far from 0.526 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part; compare against a matching rail on a known-good board where possible.
PP5V_S4_EXTA_ILIM0.526––
AI: what PP5V_S4_EXTA_ILIM is and how to check it

PP5V_S4_EXTA_ILIM is a 5 V rail at the S4 startup stage, judging by its name; the "ILIM" suffix usually marks a current-limit reference or sense node (general interpretation, not from board data). The only known-good reading here is a diode value of 0.526 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the net to ground, then power up and measure the voltage. A diode reading far from 0.526 usually points to a short or a leaky component on the rail, but a single reading doesn't confirm a bad part.

PP5V_S4_EXTB_F0.525––
AI: what PP5V_S4_EXTB_F is and how to check it

PP5V_S4_EXTB_F — reference note

  • What it is: a 5 V rail in the S4 startup stage, judging from the name (PP = power rail, 5V = 5 volts, S4 = the S4 power state, EXTB = external/backlight-related). The exact loads on it aren't known for this board.
  • Known-good reading: diode-to-ground 0.525 in the readings archive, no condition recorded. There is no known-good voltage reading here.
  • How to check: power off and unplugged, meter in diode mode, black probe on ground, red on the rail — expect around 0.525. Then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open trace or missing part. A missing voltage with a normal diode reading points upstream, to the S4 enable or the regulator feeding it. These are general guidelines, not confirmed causes for this board.
PP5V_S4_EXTB_ILIM0.525––
AI: what PP5V_S4_EXTB_ILIM is and how to check it
  • What it is: From its name, PP5V_S4_EXTB_ILIM is a 5 V rail that comes up at the S4 startup stage, with "ILIM" suggesting a current-limit reference or sense point. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.525 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.525; then power up and measure the voltage, comparing with a matching rail or a known-good board since no voltage value is listed.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on that rail; a much higher one to an open trace or missing connection. Confirm with a second measurement before replacing anything.
PP5V_S4_EXTC_F0.525––
AI: what PP5V_S4_EXTC_F is and how to check it

PP5V_S4_EXTC_F is a 5 V rail in the S4 startup stage, judging by its name (S4 = a later power state, EXTC = external/connector-related). The only known-good reading here is a diode value of 0.525 to ground; no known-good voltage reading is recorded.

  • Check it with the board unpowered: multimeter in diode mode, black probe on ground, red on the rail.
  • Then apply power and measure the DC voltage on the rail.

A diode reading far below 0.525 usually points to a short or a leaky part on that rail; a much higher or open reading suggests a broken path or missing component. A missing or low voltage with a good diode reading points upstream, to whatever enables S4. These are general guidelines, not confirmed causes for this board.

PP5V_S4_EXTC_ILIM0.525––
AI: what PP5V_S4_EXTC_ILIM is and how to check it

PP5V_S4_EXTC_ILIM (820-3482) — reference note

  • From its name, this is a 5 V rail that appears in the S4 startup stage, with "ILIM" suggesting a current-limit reference or sense node rather than a heavy load rail. The board data has no description beyond the name, so treat that as general interpretation.
  • Known-good reading in the archive: diode 0.525 to ground. That is a community guide, not a factory value; no known-good voltage or resistance reading is recorded here.
  • To check it: power off and unplug, then measure diode mode from the net to ground and compare with 0.525. Then apply power and measure the voltage, comparing against a matching S4 rail or a known-good board.
  • A diode reading far below 0.525 usually points to a short or a leaky part on the net; far above it can mean an open trace or missing component. Confirm with a second measurement before replacing anything.
PP5V_S4_EXTD_F0.523––
AI: what PP5V_S4_EXTD_F is and how to check it

PP5V_S4_EXTD_F is a 5 V rail in the S4 startup stage, judging by its name (S4 is a later stage in the usual Apple power sequence, general knowledge, not from this board's data). The only known-good reading here is a diode value of 0.523 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.523 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S4_EXTD_ILIM0.523––
AI: what PP5V_S4_EXTD_ILIM is and how to check it

PP5V_S4_EXTD_ILIM is a 5 V rail in the S4 startup stage, judging by its name; the "ILIM" suffix usually marks a current-limit reference or sense point (general naming convention, not from this board's data). The only known-good reading here is a diode value of 0.523 to ground, with no condition stated, and there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.523 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything.

S3: memory 7

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP3V3_S3_VREFMRGN0.341––
AI: what PP3V3_S3_VREFMRGN is and how to check it
  • What it is: PP3V3_S3_VREFMRGN is a 3.3 V S3 (memory-stage) rail, judged from its name; the "VREFMRGN" suffix suggests a reference/margin-related supply, but that's inference, not board data.
  • Known-good: diode reading to ground is 0.341 (community archive, no condition given). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open path. Confirm with voltage before replacing anything.
PPVDDQ_S30.321–318.000
AI: what PPVDDQ_S3 is and how to check it

PPVDDQ_S3 is a memory rail; the S3 suffix in its name indicates the memory startup stage. Known-good readings in the archive are diode 0.321 and resistance 318.000, with no condition noted, so treat them as a guide. Check it unpowered in diode mode to ground, then measure the voltage with the board powered. A diode reading far from 0.321 usually points to a short or leaky part on that rail, but one reading alone doesn't confirm a bad part. No known-good voltage reading is listed here, so compare against a matching rail or a known-good board.

PPVDDQ_S3_DDR––318.000
AI: what PPVDDQ_S3_DDR is and how to check it

PPVDDQ_S3_DDR is the DDR memory supply rail that comes up in the S3 (memory) stage, judged from its name. The only known-good reading here is 318.000 in resistance mode; there is no known-good diode or voltage reading for this rail. Check it unpowered in diode mode to ground first, then measure the voltage with the board powered in that state. A resistance far from 318.000 usually points to a short or a leaky part on the rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PPVREF_S3_MEM_VREFCA_A0.583––
AI: what PPVREF_S3_MEM_VREFCA_A is and how to check it

PPVREF_S3_MEM_VREFCA_A is a memory reference voltage in the S3 (suspend-to-RAM) power state, judged from its name; it is not a main rail. The archive lists one known-good reading: diode 0.583 in diode mode to ground with the board unpowered. Check it that way first, then measure the voltage with power applied — there is no known-good voltage reading for this net, so compare against a matching reference net or a known-good board. A diode reading far from 0.583 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PPVREF_S3_MEM_VREFCA_B0.583––
AI: what PPVREF_S3_MEM_VREFCA_B is and how to check it
  • What it is: From the name, a memory reference voltage in the S3 (suspend-to-RAM) power domain. The board data doesn't list which parts sit on this net.
  • Known-good reading: diode 0.583 in the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from PPVREF_S3_MEM_VREFCA_B to ground; then power up and measure the voltage on the net.
  • If it's far off: a much lower diode reading usually points to a short or leaky part on the net, but that isn't confirmed until traced. Compare against a matching reference net or a known-good board before replacing anything.
PPVREF_S3_MEM_VREFDQ_A0.582––
AI: what PPVREF_S3_MEM_VREFDQ_A is and how to check it
  • What it is: A memory reference voltage, from the name: an S3-state DDR VREFDQ rail on the 820-3482.
  • Known-good reading: diode 0.582 to ground, no condition listed. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure its DC voltage.
  • Far from 0.582 in diode mode usually points to a short or a leaky part on that net, but one reading isn't proof.
PPVREF_S3_MEM_VREFDQ_B0.586––
AI: what PPVREF_S3_MEM_VREFDQ_B is and how to check it

PPVREF_S3_MEM_VREFDQ_B is a memory reference voltage that comes up in the S3 (suspend-to-RAM) stage; that much is from the name, not from a schematic. The only known-good figure here is a diode reading of 0.586 to ground, with no condition noted, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the net to ground, then power the board and measure the DC voltage. A diode reading far below 0.586 usually suggests a short or a leaky part on the net, while a much higher one can mean an open path; treat the figure as a guide and compare against a matching net or a known-good board before condemning anything.

S0: running 36

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.079–78.500R
AI: what PP1V05_S0 is and how to check it
  • What it is: PP1V05_S0 is a 1.05 V rail that is up in the S0 (running) state, judged from the name; the board data has no part list, so which components sit on it isn't known.
  • Known-good readings (community guide): diode 0.079 to ground, resistance 78.500R. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode and resistance from the rail to ground; then power up and measure the voltage on the rail.
  • If far off: a much lower diode or resistance reading usually points to a short or a leaking part on the rail, but one reading isn't proof — compare against a matching rail or a known-good board before replacing anything.
PP1V5_S00.142–140.800
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V supply rail; the "S0" suffix indicates it belongs to the running (S0) power state, from the name. The archived readings for this rail are a diode value of 0.142 and a resistance of 140.800 — treat these as a community guide, not a guaranteed good value. To check it, power the board off and measure diode mode from PP1V5_S0 to ground, then apply power and measure the voltage on the rail. A diode reading far below 0.142 suggests a short or leaky load on the rail; a voltage well off 1.5 V points to a supply or enable problem. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PP1V5_S0_PCH0.142–140.800
AI: what PP1V5_S0_PCH is and how to check it
  • What it is: PP1V5_S0_PCH is a 1.5 V rail for the PCH, from its name; the S0 suffix means it's up in the running state.
  • Known-good readings: diode 0.142 and resistance 140.8 Ω, from the readings archive. These are community values and a guide only; no known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground, then resistance to ground; then power up and measure the voltage.
  • If it's far off: a much lower diode or resistance reading usually points to a short or a leaky part on the rail, but one reading doesn't confirm a bad part. Compare with a matching rail or a known-good board before replacing anything.
PP1V05_S0_PCH_VCC_CLK_F0.079––
AI: what PP1V05_S0_PCH_VCC_CLK_F is and how to check it
  • What it is: PP1V05_S0_PCH_VCC_CLK_F is a 1.05 V supply rail for the PCH clock section, from its name; the S0 suffix means it's up in the running state.
  • Known-good reading: diode 0.079 to ground, from the readings archive. This is a community value and only a guide; there's no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.079. Then power up and measure the voltage, which should be about 1.05 V by the rail's name, though no measured voltage is recorded.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a high or open reading suggests a broken feed. Either way, confirm with the voltage measurement before replacing anything.
PP3V3_S00.358––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V rail for the S0 (running) state, as the name indicates. The archive lists a diode reading of 0.358 to ground for this rail; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S0 to ground and compare with 0.358. Then power the board and check the voltage, comparing against a known-good board since no voltage value is listed. A diode reading far below 0.358 usually suggests a short or leaky load on the rail; a far higher reading can mean an open connection. These are general guidelines, not confirmed values for this board.

PP3V3_S0_BKLT_VDDIO_R0.359––
AI: what PP3V3_S0_BKLT_VDDIO_R is and how to check it
  • What it is: A 3.3 V rail (PP3V3) that is on in the S0 running state, and by its name it feeds backlight-related VDDIO. The name is the only source for that; the parts it powers aren't known here.
  • Known-good reading: diode 0.359 in the readings archive. That's a community guide, not a factory spec, and it varies with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.359; then apply power and measure the rail voltage. No known-good voltage reading is listed here, so compare against a matching rail on a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, while an open or high reading points to a broken feed. Confirm with a second measurement before replacing anything.
PP3V3_S0_SSD0.453––
AI: what PP3V3_S0_SSD is and how to check it

PP3V3_S0_SSD is a 3.3 V supply rail; the S0 in the name indicates it belongs to the running (S0) power state, and SSD suggests it feeds the SSD section. The archive lists one known-good diode reading, 0.453, with no condition noted, and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.453 usually points to a short or a leaky part on that rail, but a single reading isn't proof of a bad part.

PP3V3_S0_SSD_FLT0.453––
AI: what PP3V3_S0_SSD_FLT is and how to check it
  • What it is: PP3V3_S0_SSD_FLT is a 3.3 V rail, from its name: the "S0" state means it is up when the board is running, and "SSD" suggests it feeds the SSD side of the circuit. "FLT" usually means a filtered or fault-related branch, but that is general naming, not confirmed by this board's data.
  • Known-good reading: diode 0.453 to ground in diode mode, with no condition recorded. There is no known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail, but one reading isn't proof. Compare with a matching net or a known-good board before replacing anything.
PP3V3_S0_SW_SD_PWR0.564––
AI: what PP3V3_S0_SW_SD_PWR is and how to check it
  • What it is: From its name, PP3V3_S0_SW_SD_PWR is a 3.3 V switched power rail for SD card power, active in the S0 (running) state. The "SW" suggests it is switched on by a control signal rather than always on.
  • Known-good reading: Diode mode to ground is 0.564, from the readings archive. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.564. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below known-good usually points to a short or leaky part on the rail; a much higher or open reading points to a broken connection. A missing voltage with a good diode reading suggests the switch or its enable signal isn't turning the rail on. These are likely causes, not confirmed ones.
PP5V_S00.410––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is the 5 V rail that is present in the S0 (running) state, based on its name. The archived reading for this net is a diode value of 0.410; no voltage or resistance known-good reading is recorded here.

  • Check it with the board unpowered: diode mode, black probe on ground, red on PP5V_S0, and compare with 0.410.
  • Then power the board and measure the DC voltage on the same net.
  • A diode reading far below 0.410 suggests a short or a leaky load on the rail; a far higher or open reading suggests a broken path. A single reading doesn't confirm a bad part, so compare against a matching rail or a known-good board before replacing anything.
PP5V_S0_BKLT_R0.408––
AI: what PP5V_S0_BKLT_R is and how to check it

PP5V_S0_BKLT_R is a 5 V backlight rail enabled in the S0 (running) state, judging from its name. The only known-good figure here is a diode reading of 0.408 to ground, with no condition noted; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground and compare with 0.408.
  • Then power the board and measure the voltage on the rail; it should come up near 5 V once the board is in S0, though that figure is general, not from this board's data.
  • A diode reading far below 0.408 suggests a short or a leaky part on the rail; a much higher or open reading suggests a broken trace or missing connection. Treat either as a lead to trace, not a confirmed fault.
PP5V_S0_GFXIMVP_VDD0.409––
AI: what PP5V_S0_GFXIMVP_VDD is and how to check it

PP5V_S0_GFXIMVP_VDD (820-3482) — reference note

  • From its name, this is a 5 V rail (PP5V) that is present in the S0 running state and feeds the graphics IMVP VDD supply. The S0 tag means it should only come up once the board is fully powered on, not in standby.
  • Known-good reading in the archive: diode 0.409 to ground. There is no known-good voltage reading here, and no condition is recorded for the diode value.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.409. Then apply power and measure the voltage on the rail; it should sit near 5 V once the board is in S0.
  • A diode reading far below 0.409 suggests a short or a leaky load on the rail; far above suggests an open path. Either way, confirm with the voltage measurement before suspecting a part, since a single reading can mislead.
PP5V_S0_HDD0.600––
AI: what PP5V_S0_HDD is and how to check it

PP5V_S0_HDD is a 5 V rail that, from its name, is switched on in the S0 (running) state and feeds the hard drive circuit. The archive lists a diode reading of 0.600 to ground for this net; no known-good voltage reading is recorded here.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.600.
  • Then power the board and measure the voltage in S0; expect about 5 V, though that figure is general, not from this board's data.
  • A diode reading far below 0.600 suggests a short or leaky load on the rail; far above it suggests an open path. Confirm with a second measurement before replacing anything.
PP12V_S00.459––
AI: what PP12V_S0 is and how to check it
  • PP12V_S0 is a 12 V rail that is up in the S0 (running) state, judging from its name; the board data doesn't list which parts sit on it.
  • Known-good: diode reading 0.459 to ground. No known-good voltage is listed here.
  • Check with the board unpowered: meter in diode mode, black probe on ground, red on the rail. Then power up and measure the voltage.
  • A diode reading far below 0.459 usually points to a short or a leaky part on that rail; far above it can mean an open connection. One reading alone doesn't confirm a bad part, so compare with the voltage under power before replacing anything.
PP12V_S0_BKLT_FILT0.459––
AI: what PP12V_S0_BKLT_FILT is and how to check it
  • What it is: From the name, PP12V_S0_BKLT_FILT is a 12 V backlight supply rail that is filtered and active in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.459 to ground, from the readings archive; treat it as a guide, since community readings vary with board state.
  • How to check: power off and check diode mode from the rail to ground, then apply power and measure the DC voltage. No known-good voltage reading is available here.
  • What a far-off reading suggests: a much lower diode reading can point to a shorted load or capacitor on the rail; a much higher one to an open trace or missing part. Confirm with a second measurement before replacing anything.
PP12V_S0_BKLT_PWR0.169––
AI: what PP12V_S0_BKLT_PWR is and how to check it

PP12V_S0_BKLT_PWR is the backlight power rail, a 12 V supply that is switched on in the S0 (running) state — both from the name. The only known-good reading in the archive is a diode value of 0.169 to ground; no known-good voltage reading is recorded here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far below 0.169 usually points to a short or a leaky load on the rail, while a much higher one can mean an open path; either way, confirm with the voltage before suspecting a part.

PP12V_S0_BKLT_PWR_R0.167––
AI: what PP12V_S0_BKLT_PWR_R is and how to check it
  • What it is: From its name, PP12V_S0_BKLT_PWR_R is a 12 V backlight power rail that is present in the S0 (running) state. The "_R" suffix usually marks a secondary or related branch of the same rail; that's general naming convention, not from this board's data.
  • Known-good reading: diode 0.167 to ground, from the readings archive. This is a community value and a guide only; no known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.167. Then power up and confirm the voltage appears when the board reaches S0.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; a much higher one suggests an open feed. Neither confirms a bad part on one reading, so trace the feed and compare against a known-good board before replacing anything.
PP12V_S0_CPUVCC_FLT0.463––
AI: what PP12V_S0_CPUVCC_FLT is and how to check it

PP12V_S0_CPUVCC_FLT is a 12 V rail tied to CPU VCC, and the S0 in its name indicates it belongs to the running (S0) power state. The only known-good figure here is a diode reading of 0.463 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered: diode mode, black probe to ground, red to the rail, and compare with 0.463.
  • Then power the board and measure the voltage; no known-good voltage is listed, so compare against a known-good board or the same rail on a matching board.
  • A diode reading far below 0.463 usually suggests a short or a leaky part on the rail; far above it can mean an open connection. Treat these as guides, not proof a part is bad.
PP12V_S0_FAN_0_FILT0.459––
AI: what PP12V_S0_FAN_0_FILT is and how to check it
  • What it is: From its name, PP12V_S0_FAN_0_FILT is a 12 V rail feeding the fan circuit, filtered, and active in the S0 (running) state. Which parts sit on it isn't known from the available data.
  • Known-good reading: diode 0.459 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a missing or low voltage with power applied points to the supply or enable side. Confirm with a second measurement before replacing anything.
PP12V_S0_FBVDDQ0.463––
AI: what PP12V_S0_FBVDDQ is and how to check it

PP12V_S0_FBVDDQ is a 12 V rail that, from its name, runs in the S0 (fully on) state and feeds the FBVDDQ supply. The only known-good reading here is a diode reading of 0.463 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and in S0.
  • A diode reading far below 0.463 usually points to a short or a leaky load on the rail; a much higher reading can mean an open trace or missing connection.
  • Readings vary with board state, so treat 0.463 as a guide and compare against a matching rail or a known-good board before condemning a part.
PP12V_S0_GPUCORE0.461––
AI: what PP12V_S0_GPUCORE is and how to check it

PP12V_S0_GPUCORE is a 12 V rail for the GPU core, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.461 to ground, with no condition noted; no known-good voltage reading is available. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.461 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PPCPUVCC_S0_CPU0.018–17.900R
AI: what PPCPUVCC_S0_CPU is and how to check it

PPCPUVCC_S0_CPU is a CPU power rail; the S0 in its name indicates it belongs to the running (S0) state, and PPCPUVCC points to the CPU core supply.

  • Known-good from the archive: diode 0.018 and resistance 17.900R. These are community readings and a guide only; no voltage reading is recorded here.
  • Check it unpowered in diode mode to ground first, then measure the voltage on the rail with the board powered and in S0.
  • A diode or resistance far below 17.900R suggests a short or a failing load on the rail; a value far above it suggests an open trace or missing part. Confirm with a second measurement before replacing anything.
PPCPUVCC_S0_SENSE_1––17.900R
AI: what PPCPUVCC_S0_SENSE_1 is and how to check it
  • What it is: PPCPUVCC_S0_SENSE_1 is a CPU core voltage sense line, judged from its name; the S0 suffix indicates the running state. The parts on this net aren't known here.
  • Known-good reading: 17.900R resistance, from the readings archive. There is no known-good diode or voltage value for this net here.
  • How to check: With the board unpowered, measure resistance or diode mode from the net to ground and compare with 17.900R; then power up and measure the voltage on the net.
  • If far off: A much lower resistance or a short to ground usually points to a fault on that sense line or its load, but one reading doesn't confirm a bad part. Compare with a matching sense net on the other side of the pair before replacing anything.
PPCPUVCC_S0_SENSE_2––17.900R
AI: what PPCPUVCC_S0_SENSE_2 is and how to check it
  • What it is: From the name, PPCPUVCC_S0_SENSE_2 is a CPU core supply (VCC) sense line that is active in the S0 running state. The board data gives no part or net connections for it.
  • Known-good reading: 17.900R resistance, with no condition stated. This is a community guide value, not a factory spec. No known-good diode or voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground, then measure resistance and compare with 17.900R. Then apply power and measure the voltage on the net.
  • What a far-off reading means: A resistance far from 17.900R, or a short to ground, usually points to a fault on the sense path or the rail it monitors. A single reading doesn't confirm a bad part, so check the related rail and the sense resistor before replacing anything.
PPCPUVCC_S0_SENSE_30.018–17.900R
AI: what PPCPUVCC_S0_SENSE_3 is and how to check it

PPCPUVCC_S0_SENSE_3 — reference note

  • What it is: from the name, a CPU core voltage (VCC) sense line active in the S0 (running) state. It is a sense/feedback node, not a power rail to load down.
  • Known-good readings (community archive, guide only): diode 0.018 and resistance 17.900R. No known-good voltage reading here.
  • How to check: power off and unplugged, diode mode from the net to ground, then resistance to ground; compare with the two values above. Then power the board into S0 and measure the voltage on the net.
  • What a far-off reading suggests: a much higher diode or resistance reading points to an open trace or missing connection to the sense point; a near-zero reading points to a short to ground. A small difference can be normal, so confirm with a second measurement before suspecting a part.
PPDDRVTT_S00.544––
AI: what PPDDRVTT_S0 is and how to check it
  • What it is: PPDDRVTT_S0 is a DDR termination-voltage rail; the "VTT" and "S0" (running state) come from the name. It's a mid-rail reference for the memory, not a main supply.
  • Known-good reading: diode 0.544 to ground, from the readings archive. That's a guide only, since readings vary with board state. No known-good voltage is recorded here.
  • How to check: power off, measure diode mode from PPDDRVTT_S0 to ground and compare with 0.544. Then power on and measure the DC voltage; general repair practice expects roughly half the DDR supply, but that's not from this board's data.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; an open or high reading suggests a broken trace or missing source. Confirm with voltage under power before replacing anything.
PPHDD_S00.600––
AI: what PPHDD_S0 is and how to check it
  • What it is: PPHDD_S0 is the hard-drive power rail, active in the S0 (running) state, judged from the rail name only. Which parts sit on it isn't known here.
  • Known-good reading: diode 0.600 to ground, with no stated condition beyond that. No known-good voltage reading is available here.
  • How to check: power off and unplug, then measure diode mode from PPHDD_S0 to ground. Then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below known-good usually points to a short or a failing part on the rail; a much higher one can mean an open path. Treat this as a guide and confirm with a second measurement before replacing anything.
PPSSD_S00.453––
AI: what PPSSD_S0 is and how to check it

PPSSD_S0 is the SSD power rail, active in the S0 (running) state, judged from the rail name. The archive lists one known-good reading: diode 0.453 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure its voltage with the board running. There is no known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far from 0.453 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

PPVCCIO_S0_CPU0.022–21.400R
AI: what PPVCCIO_S0_CPU is and how to check it

PPVCCIO_S0_CPU is the CPU's I/O supply rail; the S0 in its name means it is up in the running state. The archive lists a diode reading of 0.022 and a resistance of 21.400R, with no condition noted, so treat these as a guide only. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the rail voltage. A diode reading far below 0.022 suggests a short or a leaky load on the rail, but one reading doesn't confirm a bad part, so re-check before replacing anything. No known-good voltage reading is listed here.

PPVCOMP_S0_CPU0.044––
AI: what PPVCOMP_S0_CPU is and how to check it
  • What it is: From its name, PPVCOMP_S0_CPU is a CPU-related compensation rail in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.044 to ground, from the readings archive (community value, a guide only). No known-good voltage reading is available here.
  • How to check: Power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage on the net.
  • If it's far off: a much higher or open diode reading usually points to a broken trace or missing part on the net; a short to ground points to a failed component on that rail. Confirm with a voltage check under power before replacing anything.
PPVCORE_S0_GFX_PH10.036–33.900R
AI: what PPVCORE_S0_GFX_PH1 is and how to check it

PPVCORE_S0_GFX_PH1 is a graphics core power rail; the S0 in the name indicates it is a running-state rail, and PH1 suggests a phase node of a multi-phase supply (both from the name). Archived readings for this board give a diode reading of 0.036 and 33.900R resistance to ground; treat these as a guide, since they come from community contributions and vary with board state. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and running. A reading far from these values usually points to a short or a failed phase component, but a small difference can be normal, so confirm with a second measurement before replacing anything. No known-good voltage reading is listed here.

PPVCORE_S0_GFX_PH20.036–33.900R
AI: what PPVCORE_S0_GFX_PH2 is and how to check it

PPVCORE_S0_GFX_PH2 — reference note

  • From the name: a processor core power rail (VCORE) for the graphics section (GFX), phase 2 (PH2), active in the S0 running state. It's a switching-regulator output, so it's a low-voltage, high-current rail.
  • Known-good readings from the archive: diode 0.036 and resistance 33.900R. These are community values and a guide only; no known-good powered voltage is recorded here.
  • Check it with the board unpowered: diode mode from the rail to ground, then resistance to ground, and compare with those values. Then power the board and measure the rail voltage.
  • A diode or resistance far below known-good usually points to a short or a failing load on the rail; a voltage that never comes up points to the regulator or its enable/sequence. Confirm with a second measurement before replacing anything.
PPVCORE_S0_GPU0.036–33.900R
AI: what PPVCORE_S0_GPU is and how to check it
  • What it is: PPVCORE_S0_GPU is the GPU core power rail; the "S0" in the name indicates it is up in the running state (from the name). This is general naming, not from board data.
  • Known-good readings: diode 0.036 and resistance 33.900R, from community contributions, so treat them as a guide only. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode to ground on the rail; then apply power and measure the rail voltage.
  • If far off: a much lower diode or resistance reading usually points to a short or a failing part on the rail, but one reading alone doesn't confirm a bad part. Compare against a matching rail or a known-good board before replacing anything.
PPVDDQ_S0_GPU0.088––
AI: what PPVDDQ_S0_GPU is and how to check it

PPVDDQ_S0_GPU is a running-state (S0, from the name) supply rail, likely the GPU's VDDQ memory-interface voltage — that's general inference from the name, not from board data. The only known-good reading here is diode mode 0.088 to ground; there is no known-good voltage or resistance value for this rail. Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S0. A diode reading far from 0.088 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part — compare against a matching rail or a known-good board before replacing anything.

PPVIN_S0_GFXIMVP_R0.469––
AI: what PPVIN_S0_GFXIMVP_R is and how to check it

PPVIN_S0_GFXIMVP_R is a supply rail for the graphics IMVP regulator, from its name; the S0 suffix indicates it is present in the running state. The archive lists one known-good diode reading of 0.469 to ground, with no condition noted and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far below 0.469 usually points to a short or a leaky part on the rail; a far higher or open reading points to a broken feed or a missing connection. These are community readings and a guide only, so compare against a matching rail on a known-good board before condemning anything.

PPVOUT_S0_PCH_DCPRTC0.724––
AI: what PPVOUT_S0_PCH_DCPRTC is and how to check it
  • What it is: From its name, PPVOUT_S0_PCH_DCPRTC is a power rail (PP = power rail) that is up in S0, the running state, and feeds the PCH's DCPRTC domain. The board data has no part list, so which components sit on it isn't known.
  • Known-good reading: diode 0.724 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage on the rail.
  • If it's far off: a diode reading well below 0.724 usually suggests a short or leaky load on the rail; a much higher or open reading can mean a broken trace or missing feed. Confirm with the voltage measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
4V5_NR0.662––
4V5_REG_EN0.358––
4V5_REG_IN0.410––
ACDC_BURST0.601––
ACDC_BURST_EN_L0.761––
AGND_CPU0.000––
AGND_GPUVDDQ0.000––
AGND_P1V05S00.000––
AGND_VDDQS30.000––
ALL_SYS_PWRGD0.501––
AP_CLKREQ_L0.462––
AP_CLKREQ_Q_L0.464––
AP_EVENT_L0.753––
AP_RESET_CONN_L0.467––
AP_RESET_L0.432––
AP_WAKE_L1.923––
AUD_CODEC_MICBIAS0.551––
AUD_DMIC_CLK0.730––
AUD_DMIC_CLK_CONN0.736––
AUD_DMIC_SDA10.712––
AUD_DMIC_SDA1_CONN0.712––
AUD_GPIO_20.622––
AUD_GPIO_30.556––
AUD_HP_PORT_REFOL––
AUD_HS_MIC_NOL––
AUD_HS_MIC_P1.559––
AUD_HS_MIC_RC_NOL––
AUD_HS_MIC_RC_POL––
AUD_I2C_INT_L0.562––
AUD_IP_PERIPHERAL_DET0.586––
AUD_IP_PERPH_DET_DB0.589––
AUD_IP_PERPH_DET_ROL––
AUD_IPHS_SWITCH_EN0.522––
AUD_IPHS_SWITCH_EN_PCH0.527––
AUD_J1_DET_RCOL––
AUD_J1_GND_ANALOG0.000––
AUD_J1_HP_OUTLOL––
AUD_J1_HP_OUTROL––
AUD_J1_HP_PORT_REFOL––
AUD_J1_MIC_BIAS0.572––
AUD_J1_MIC_NOL––
AUD_J1_MIC_P1.559––
AUD_J1_PP3V3_S00.332––
AUD_J1_TIPDET1_ROL––
AUD_J1_TIPDET2_ROL––
AUD_J1_TYPEDET_ROL––
AUD_LAMP_AVDD0.525––
AUD_LAMP_BOOTLN0.584––
AUD_LAMP_BOOTLP0.585––
AUD_LAMP_BOOTRN0.584––
AUD_LAMP_BOOTRP0.586––
AUD_LAMP_EDGE0.525––
AUD_LAMP_GAIN0.595––
AUD_LAMP_LIN_N0.600––
AUD_LAMP_LIN_P0.600––
AUD_LAMP_LINC_N0.730––
AUD_LAMP_LINC_P0.725––
AUD_LAMP_MONO0.000––
AUD_LAMP_OUTNL0.553––
AUD_LAMP_OUTNR0.554––
AUD_LAMP_OUTPL0.553––
AUD_LAMP_OUTPR0.555––
AUD_LAMP_RIN_N0.595––
AUD_LAMP_RIN_P0.594––
AUD_LAMP_RINC_N0.725––
AUD_LAMP_RINC_P0.724––
AUD_LI_COM0.740––
AUD_LI_P_L0.745––
AUD_LI_P_R0.746––
AUD_LI_TIPDET0.389––
AUD_LO1_L_C_NOL––
AUD_LO1_L_C_POL––
AUD_LO1_L_N0.724––
AUD_LO1_L_P0.725––
AUD_LO1_R_C_NOL––
AUD_LO1_R_C_POL––
AUD_LO1_R_N0.723––
AUD_LO1_R_P0.726––
AUD_LO2_L_N0.725––
AUD_LO2_L_P0.730––
AUD_LO2_R_N0.726––
AUD_LO2_R_P0.728––
AUD_MIC_INL_N0.745––
AUD_MIC_INL_P0.745––
AUD_MIC_INN_R0.745––
AUD_MIC_INP_R0.745––
AUD_OUTJACK_INSERT0.618––
AUD_OUTJACK_INSERT_L0.620––
AUD_PORTA_DET_L0.609––
AUD_PORTB_DET_L1.169––
AUD_PORTC_DET_L0.612––
AUD_PORTD_DET_L1.099––
AUD_RAMP_AVDD0.526––
AUD_RAMP_BOOTLN0.585––
AUD_RAMP_BOOTLP0.588––
AUD_RAMP_BOOTRN0.585––
AUD_RAMP_BOOTRP0.587––
AUD_RAMP_EDGE0.526––
AUD_RAMP_GAIN0.591––
AUD_RAMP_LIN_N0.593––
AUD_RAMP_LIN_P0.599––
AUD_RAMP_LINC_N0.723––
AUD_RAMP_LINC_P0.726––
AUD_RAMP_MONO0.000––
AUD_RAMP_OUTNL0.558––
AUD_RAMP_OUTNR0.557––
AUD_RAMP_OUTPL0.558––
AUD_RAMP_OUTPR0.558––
AUD_RAMP_RIN_N0.591––
AUD_RAMP_RIN_P0.591––
AUD_RAMP_RINC_N0.728––
AUD_RAMP_RINC_P0.726––
AUD_SDI_R0.481––
AUD_SENSE_A0.765––
AUD_SPDIF_CHIP0.707––
AUD_SPDIF_OUT0.730––
AUD_SPKR_LTWT_OUT_N0.566––
AUD_SPKR_LTWT_OUT_P0.565––
AUD_SPKR_LWFR_OUT_N0.565––
AUD_SPKR_LWFR_OUT_P0.564––
AUD_SPKR_RTWT_OUT_N0.558––
AUD_SPKR_RTWT_OUT_P0.559––
AUD_SPKR_RWFR_OUT_N0.558––
AUD_SPKR_RWFR_OUT_P0.557––
AUD_SPKR_VENDOR_ID_LOL––
AUD_SPKR_VENDOR_ID_ROL––
AUD_SPKRAMP_MAC_SHDN_L0.551––
AUD_SPKRAMP_WIN_SHDN_L0.556––
AUD_TIPDET_INVOL––
AUD_TIPDET1_ROL––
AUD_TIPDET2_ROL––
AUD_TYPEDET_ODOL––
AUD_TYPEDET_OD_INV0.465––
AUD_TYPEDET_ROL––
BKLT_BOOST0.416––
BKLT_BOOST_10.141––
BKLT_BOOST_20.414––
BKLT_EN0.569––
BKLT_EN_DIV0.721––
BKLT_EN_LOL––
BKLT_FB0.706––
BKLT_FB_R0.414––
BKLT_FB_XW0.414––
BKLT_FLT0.574––
BKLT_FLT_RCOL––
BKLT_GATE0.499––
BKLT_GATE_R0.498––
BKLT_ISEN10.655––
BKLT_ISEN1_R1.120––
BKLT_ISEN20.656––
BKLT_ISEN2_R1.109––
BKLT_ISEN30.656––
BKLT_ISEN3_R1.100––
BKLT_ISEN40.653––
BKLT_ISEN4_R1.122––
BKLT_ISEN50.653––
BKLT_ISEN5_R1.104––
BKLT_ISEN60.653––
BKLT_ISEN6_R1.129––
BKLT_ISET0.571––
BKLT_PHASE0.169––
BKLT_SCL0.509––
BKLT_SDA0.519––
BKLT_SHUTDOWN0.722––
BKLT_SNUBBEROL––
BKLT_SW_N0.000––
BKLT_SW_P0.000––
BKLT_SW_R0.000––
BKLT_VSYNC0.574––
BKLT_VSYNC_R0.574––
BT_PWR_EN0.447––
BT_PWR_RSTOL––
BT_PWR_RST_L0.733––
BT_RESET_MASK_L0.456––
BURSTMODE_ENOL––
BURSTMODE_EN_L0.994––
BURSTMODE_EN_R_L1.959––
CAM_AGND0.000––
CAM_EXT_BOOT0.529––
CAM_P1V2_RST_HOLDOFF1.352––
CAM_P1V2_RST_HOLDOFF_L1.373––
CAM_PLLGND0.000––
CAM_PROC_RESET0.682––
CAM_PROC_RESET_L0.529––
CAM_RX0.527––
CAM_SF_CLK0.490––
CAM_SF_CLK_R0.000––
CAM_SF_CS_L0.492––
CAM_SF_DIN0.519––
CAM_SF_DIN_R0.538––
CAM_SF_DOUT0.583––
CAM_SF_DOUT_R0.536––
CAM_SF_HOLD_L0.722––
CAM_SF_WP_L0.535––
CAM_TEST0.048––
CAM_TX0.532––
CAM_USB_VRES0.815––
CAM_XTAL_IN0.484––
CAM_XTAL_OUT0.548––
CAM_XTAL_OUT_R0.596––
CORE_VOLTAGES_ON0.594––
CORE_VOLTAGES_ON_R1.332––
CPU_CATERR_L0.261––
CPU_CFG_RCOMP0.051––
CPU_CFG<0>0.260––
CPU_CFG<1>0.265––
CPU_CFG<2>0.248––
CPU_CFG<3>0.259––
CPU_CFG<4>0.264––
CPU_CFG<5>0.259––
CPU_CFG<6>0.263––
CPU_CFG<7>0.259––
CPU_CFG<9>0.261––
CPU_CFG<17>0.257––
CPU_CFG<19>0.259––
CPU_CLK135M_DPLLREF_N0.292––
CPU_CLK135M_DPLLREF_P0.295––
CPU_CLK135M_DPLLSS_N0.297––
CPU_CLK135M_DPLLSS_P0.299––
CPU_DIMM_VREFCA0.770––
CPU_DIMMA_VREFDQ0.771––
CPU_EDP_RCOMP0.068––
CPU_MEM_RESET_L0.352––
CPU_MEM_VREFCA_A_ISOL0.585––
CPU_MEM_VREFCA_B_ISOL0.584––
CPU_MEM_VREFDQ_A_ISOL0.585––
CPU_MEM_VREFDQ_B_ISOL0.586––
CPU_PECI0.371––
CPU_PECI_R0.333––
CPU_PEG_RCOMP0.069––
CPU_PROCHOT_L0.077–75.400R
CPU_PROCHOT_R_L0.127––
CPU_PWR_DEBUG0.229––
CPU_PWRGD0.381––
CPU_RESET_L0.383––
CPU_SKTOCC0.612––
CPU_SKTOCC_LOL––
CPU_SM_RCOMP<0>0.101––
CPU_SM_RCOMP<1>0.076––
CPU_SM_RCOMP<2>0.101––
CPU_THRMTRIP_3V30.732––
CPU_THRMTRIP_LOL––
CPU_TT_OC_LOL––
CPU_VCCSENSE_N0.005–2.600R
CPU_VCCSENSE_P––19.500R
CPU_VCCSENSE_R_N0.000––
CPU_VCCSENSE_R_P0.019–19.500R
CPU_VIDALERT_L0.098––
CPU_VIDALERT_R_L0.594––
CPU_VIDSCLK0.078–77.400R
CPU_VIDSCLK_R0.565––
CPU_VIDSOUT0.078–77.400R
CPU_VIDSOUT_R0.080––
CPUVCC_COMP_RCOL––
CPUVCC_DVC_RC2.308––
CPUVCC_FB_R_10.366––
CPUVCC_FB_R_20.040–39.400R
CPUVCC_FB_RC0.290––
CPUVCC_FB_RC_2OL––
CPUVCC_IMON_R1.011––
CPUVCC_PSICOMP_RC1.380––
CS4206_DMIC_SCL0.707––
CS4206_FLYC0.443––
CS4206_FLYN1.187––
CS4206_FLYP0.627––
CS4206_FN1.570––
CS4206_FP0.467––
CS4206_HPREF0.000––
CS4206_VCOM0.637––
CS4206_VREF_ADC0.761––
DEBUG_RESET_L0.593––
DGND_BKLT0.000––
DMI_CLK100M_CPU_N0.292––
DMI_CLK100M_CPU_P0.294––
DMI_N2S_N<0>0.292––
DMI_N2S_N<1>0.293––
DMI_N2S_N<3>0.291––
DMI_S2N_N<0>0.301––
DMI_S2N_N<3>0.389––
DMI_S2N_P<0>0.386––
DMI_S2N_P<1>0.392––
DMI_S2N_P<3>0.301––
DP_A_AUXCH_DDC_N0.701––
DP_A_AUXCH_DDC_P0.704––
DP_A_LSX_ML_N<1>0.720––
DP_A_LSX_ML_P<1>0.735––
DP_AUXIO_EN0.542––
DP_B_AUXCH_DDC_N0.705––
DP_B_AUXCH_DDC_P0.700––
DP_B_LSX_ML_N<1>0.720––
DP_B_LSX_ML_P<1>0.736––
DP_INT_EG_AUX_C_N0.740––
DP_INT_EG_AUX_C_P0.742––
DP_INT_EG_AUX_N0.805––
DP_INT_EG_AUX_P0.806––
DP_INT_EG_HPD0.535––
DP_INT_EG_ML_N<0>0.419––
DP_INT_EG_ML_N<1>0.417––
DP_INT_EG_ML_P<0>0.420––
DP_INT_EG_ML_P<1>0.417––
DP_INT_SPDIF_AUDIO0.775––
DP_INTPNL_AUX_N0.745––
DP_INTPNL_AUX_P0.732––
DP_INTPNL_HPD0.545––
DP_INTPNL_ML_C_N<0>0.472––
DP_INTPNL_ML_C_N<1>0.472––
DP_INTPNL_ML_C_P<0>0.472––
DP_INTPNL_ML_C_P<1>0.472––
DP_INTPNL_ML_N<0>OL––
DP_INTPNL_ML_N<1>OL––
DP_INTPNL_ML_P<0>OL––
DP_INTPNL_ML_P<1>OL––
DP_TBT_SEL0.388––
DP_TBTPA_AUXCH_C_P0.594––
DP_TBTPA_AUXCH_N0.736––
DP_TBTPA_AUXCH_P0.735––
DP_TBTPA_DDC_DATA0.523––
DP_TBTPA_HPD0.562––
DP_TBTPA_ML_C_N<1>0.323––
DP_TBTPA_ML_C_N<3>0.322––
DP_TBTPA_ML_C_P<1>0.323––
DP_TBTPA_ML_C_P<3>0.322––
DP_TBTPA_ML_N<1>0.679––
DP_TBTPA_ML_N<3>OL––
DP_TBTPA_ML_P<1>0.695––
DP_TBTPA_ML_P<3>OL––
DP_TBTPB_AUXCH_C_N0.515––
DP_TBTPB_AUXCH_C_P0.622––
DP_TBTPB_DDC_DATA0.517––
DP_TBTPB_HPD0.557––
DP_TBTPB_ML_C_N<1>0.322––
DP_TBTPB_ML_C_N<3>0.324––
DP_TBTPB_ML_C_P<1>0.321––
DP_TBTPB_ML_C_P<3>0.323––
DP_TBTPB_ML_N<1>0.681––
DP_TBTPB_ML_N<3>OL––
DP_TBTPB_ML_P<1>0.701––
DP_TBTPB_ML_P<3>OL––
DP_TBTSNK0_AUXCH_C_N0.800––
DP_TBTSNK0_AUXCH_C_P0.800––
DP_TBTSNK0_AUXCH_N0.543––
DP_TBTSNK0_AUXCH_P0.555––
DP_TBTSNK0_DDC_CLK0.536––
DP_TBTSNK0_DDC_DATA0.533––
DP_TBTSNK0_HPD0.522––
DP_TBTSNK0_ML_C_N<0>0.436––
DP_TBTSNK0_ML_C_N<1>0.440––
DP_TBTSNK0_ML_C_N<2>0.436––
DP_TBTSNK0_ML_C_N<3>0.439––
DP_TBTSNK0_ML_C_P<0>0.437––
DP_TBTSNK0_ML_C_P<1>0.441––
DP_TBTSNK0_ML_C_P<2>0.436––
DP_TBTSNK0_ML_C_P<3>0.440––
DP_TBTSNK0_ML_N<0>0.585––
DP_TBTSNK0_ML_N<1>0.580––
DP_TBTSNK0_ML_N<2>0.580––
DP_TBTSNK0_ML_N<3>0.580––
DP_TBTSNK0_ML_P<0>0.580––
DP_TBTSNK0_ML_P<1>0.580––
DP_TBTSNK0_ML_P<2>0.580––
DP_TBTSNK0_ML_P<3>0.580––
DP_TBTSNK1_AUXCH_C_N0.800––
DP_TBTSNK1_AUXCH_C_P0.800––
DP_TBTSNK1_AUXCH_N0.566––
DP_TBTSNK1_AUXCH_P0.625––
DP_TBTSNK1_DDC_CLK0.538––
DP_TBTSNK1_DDC_DATA0.533––
DP_TBTSNK1_HPD0.521––
DP_TBTSNK1_ML_C_N<0>0.436––
DP_TBTSNK1_ML_C_N<1>0.437––
DP_TBTSNK1_ML_C_N<2>0.435––
DP_TBTSNK1_ML_C_N<3>0.434––
DP_TBTSNK1_ML_C_P<0>0.435––
DP_TBTSNK1_ML_C_P<1>0.437––
DP_TBTSNK1_ML_C_P<2>0.433––
DP_TBTSNK1_ML_C_P<3>0.434––
DP_TBTSNK1_ML_N<0>0.580––
DP_TBTSNK1_ML_N<1>0.580––
DP_TBTSNK1_ML_N<2>0.580––
DP_TBTSNK1_ML_N<3>0.580––
DP_TBTSNK1_ML_P<0>0.580––
DP_TBTSNK1_ML_P<1>0.580––
DP_TBTSNK1_ML_P<2>0.580––
DP_TBTSNK1_ML_P<3>0.580––
DP_TBTSRC_AUX_C_N0.735––
DP_TBTSRC_AUX_C_P0.735––
DP_TBTSRC_AUXCH_N0.560––
DP_TBTSRC_AUXCH_P0.605––
DP_TBTSRC_HPD0.536––
DP_TBTSRC_ML_C_N<0>0.502––
DP_TBTSRC_ML_C_N<1>0.501––
DP_TBTSRC_ML_C_P<0>0.501––
DP_TBTSRC_ML_C_P<1>0.502––
DP_TBTSRC_ML_N<0>0.324––
DP_TBTSRC_ML_N<1>0.324––
DP_TBTSRC_ML_P<0>0.323––
DP_TBTSRC_ML_P<1>0.322––
DPMUX_UC_IRQ0.737––
ENET_ACTOL––
ENET_ASF_GPIO0.747––
ENET_CLKREQ_L0.818––
ENET_CR_DATA<0>0.554––
ENET_CR_DATA<1>0.552––
ENET_CR_DATA<2>0.556––
ENET_CR_DATA<3>0.557––
ENET_CR_DATA<4>0.765––
ENET_CR_DATA<5>0.765––
ENET_CR_DATA<6>0.764––
ENET_CR_DATA<7>0.764––
ENET_CR_PWREN0.541––
ENET_CS_L0.709––
ENET_LOW_PWR_PCH0.660––
ENET_MEDIA_SENSE0.450––
ENET_MISO0.708––
ENET_MOSI0.733––
ENET_RESET_L0.460––
ENET_SCLK0.733––
ENET_SD_CLK0.559––
ENET_SD_CMD0.550––
ENET_SD_DETECT_L0.461––
ENET_SD_RESET_L0.427––
ENET_SR_DISABLE0.573––
ENET_SR_LX0.297––
ENET_TRAFFICLED_L0.760––
ENET_VMAIN_PRSNT0.632––
ENET_WAKE_L0.585––
ENET_XTALVDDH0.366––
ENETCONN_MCT_BSOL––
ENETCONN_MCT0OL––
ENETCONN_MCT1OL––
ENETCONN_MCT2OL––
ENETCONN_MCT3OL––
ENETCONN_MDI_N<0>0.384––
ENETCONN_MDI_N<1>0.385––
ENETCONN_MDI_N<2>0.385––
ENETCONN_MDI_N<3>0.386––
ENETCONN_MDI_P<0>0.384––
ENETCONN_MDI_P<1>0.385––
ENETCONN_MDI_P<2>0.384––
ENETCONN_MDI_P<3>0.385––
ENETCONN_MDI_T_N<0>OL––
ENETCONN_MDI_T_N<1>OL––
ENETCONN_MDI_T_N<2>OL––
ENETCONN_MDI_T_N<3>OL––
ENETCONN_MDI_T_P<0>OL––
ENETCONN_MDI_T_P<1>OL––
ENETCONN_MDI_T_P<2>OL––
ENETCONN_MDI_T_P<3>OL––
ENETCONN_TCT0.384––
FAN_0_PWM_FET1.230––
FAN_0_PWM_FILT1.231––
FAN_0_TACH_FETOL––
FAN_0_TACH_FILTOL––
FB_A0_A<2>0.413––
FB_A0_A<6>0.408––
FB_A0_ABI_L0.407––
FB_A0_CAS_L0.407––
FB_A0_CKE_L0.406––
FB_A0_CLK_N0.510––
FB_A0_CS_L0.409––
FB_A0_DBI_L<0>0.380––
FB_A0_DBI_L<1>0.379––
FB_A0_DQ<2>0.385––
FB_A0_DQ<3>0.379––
FB_A0_DQ<7>0.384––
FB_A0_DQ<8>0.385––
FB_A0_DQ<9>0.384––
FB_A0_DQ<11>0.385––
FB_A0_DQ<12>0.380––
FB_A0_DQ<13>0.379––
FB_A0_DQ<16>0.379––
FB_A0_DQ<19>0.381––
FB_A0_DQ<22>0.381––
FB_A0_DQ<23>0.380––
FB_A0_DQ<24>0.380––
FB_A0_DQ<26>0.379––
FB_A0_DQ<29>0.380––
FB_A0_DQ<31>0.378––
FB_A0_EDC<0>0.390––
FB_A0_EDC<1>0.385––
FB_A0_EDC<3>0.380––
FB_A0_MF0.122––
FB_A0_RAS_L0.408––
FB_A0_SEN0.121––
FB_A0_VREFC0.320––
FB_A0_VREFD0.330––
FB_A0_WCLK_N<0>0.574––
FB_A0_WCLK_P<0>0.592––
FB_A0_WCLK_P<1>0.566––
FB_A0_WE_L0.407––
FB_A1_A<0>0.414––
FB_A1_A<6>0.411––
FB_A1_ABI_L0.412––
FB_A1_CAS_L0.407––
FB_A1_CLK_N0.506––
FB_A1_CLK_P0.506––
FB_A1_CS_L0.411––
FB_A1_DBI_L<2>0.377––
FB_A1_DQ<2>0.382––
FB_A1_DQ<4>0.383––
FB_A1_DQ<5>0.383––
FB_A1_DQ<6>0.382––
FB_A1_DQ<7>0.382––
FB_A1_DQ<8>0.381––
FB_A1_DQ<11>0.377––
FB_A1_DQ<12>0.382––
FB_A1_DQ<13>0.380––
FB_A1_DQ<14>0.382––
FB_A1_DQ<15>0.381––
FB_A1_DQ<16>0.383––
FB_A1_DQ<19>0.381––
FB_A1_DQ<21>0.382––
FB_A1_DQ<22>0.380––
FB_A1_DQ<23>0.377––
FB_A1_DQ<24>0.380––
FB_A1_DQ<25>0.377––
FB_A1_DQ<26>0.377––
FB_A1_DQ<30>0.381––
FB_A1_DQ<31>0.382––
FB_A1_EDC<0>0.383––
FB_A1_EDC<1>0.382––
FB_A1_EDC<2>0.382––
FB_A1_EDC<3>0.382––
FB_A1_MF0.646––
FB_A1_RAS_L0.413––
FB_A1_SEN0.123––
FB_A1_VREFC0.323––
FB_A1_VREFD0.333––
FB_A1_WCLK_N<0>0.572––
FB_A1_WCLK_N<1>0.573––
FB_A1_WCLK_P<0>0.574––
FB_A1_WE_L0.411––
FB_A1_ZQ0.123––
FB_B0_A<2>0.417––
FB_B0_A<3>0.431––
FB_B0_A<6>0.415––
FB_B0_A<8>0.415––
FB_B0_CKE_L0.417––
FB_B0_CLK_P0.514––
FB_B0_CS_L0.418––
FB_B0_DBI_L<0>0.389––
FB_B0_DBI_L<1>0.389––
FB_B0_DQ<0>0.387––
FB_B0_DQ<2>0.388––
FB_B0_DQ<7>0.388––
FB_B0_DQ<9>0.388––
FB_B0_DQ<12>0.388––
FB_B0_DQ<15>0.391––
FB_B0_DQ<18>0.388––
FB_B0_DQ<20>0.387––
FB_B0_DQ<21>0.389––
FB_B0_DQ<22>0.388––
FB_B0_DQ<26>0.389––
FB_B0_DQ<27>0.391––
FB_B0_DQ<30>0.388––
FB_B0_DQ<31>0.388––
FB_B0_EDC<0>0.390––
FB_B0_EDC<1>0.391––
FB_B0_EDC<2>0.390––
FB_B0_EDC<3>0.391––
FB_B0_SEN0.123––
FB_B0_VREFC0.321––
FB_B0_VREFD0.335––
FB_B0_WCLK_N<0>0.586––
FB_B0_WCLK_N<1>0.587––
FB_B0_WCLK_P<0>0.590––
FB_B0_WCLK_P<1>0.581––
FB_B1_A<0>0.420––
FB_B1_A<2>0.416––
FB_B1_A<3>0.413––
FB_B1_A<6>0.416––
FB_B1_A<8>0.417––
FB_B1_CAS_L0.413––
FB_B1_CS_L0.414––
FB_B1_DBI_L<2>0.384––
FB_B1_DQ<3>0.384––
FB_B1_DQ<5>0.384––
FB_B1_DQ<6>0.384––
FB_B1_DQ<7>0.385––
FB_B1_DQ<9>0.386––
FB_B1_DQ<10>0.385––
FB_B1_DQ<11>0.385––
FB_B1_DQ<12>0.385––
FB_B1_DQ<15>0.385––
FB_B1_DQ<16>0.384––
FB_B1_DQ<19>0.384––
FB_B1_DQ<22>0.385––
FB_B1_DQ<24>0.385––
FB_B1_DQ<26>0.386––
FB_B1_DQ<27>0.385––
FB_B1_DQ<28>0.385––
FB_B1_DQ<31>0.385––
FB_B1_EDC<0>0.386––
FB_B1_EDC<1>0.385––
FB_B1_MF0.640––
FB_B1_RAS_L0.418––
FB_B1_RESET_L0.415––
FB_B1_SEN0.123––
FB_B1_VREFC0.319––
FB_B1_VREFD0.332––
FB_B1_WCLK_N<0>0.576––
FB_B1_WCLK_P<0>0.575––
FB_B1_WCLK_P<1>0.571––
FB_B1_WE_L0.413––
FB_CLAMP0.540––
FB_CLAMP_TOGGLE_REQ_L0.557––
FB_SW_LEG0.213––
FB_VREF0.670––
FBA1_CK_MID0.510––
FBB1_CK_MID0.507––
FBVDD_ALTVO0.517––
FDI_INT0.426––
FET_EN_P12V_S50.679––
FET_EN_P12V_S5_ROL––
FET_RAMP_P3V3_S00.738––
FET_RAMP_P3V3_S40.739––
FW_PME_L0.757––
FW_PWR_EN_PCH0.540––
G3_POWERON_L0.754––
GFXIMVP_VID<0>0.513––
GFXIMVP_VID<1>0.512––
GFXIMVP_VID<2>0.509––
GFXIMVP_VID<3>0.514––
GFXIMVP_VID<4>0.542––
GFXIMVP_VID<5>0.543––
GFXIMVP_VID<6>0.544––
GFXIMVP6_IMON0.542––
GFXIMVP6_IMON_R0.680––
GND0.000––
GND_AUDIO_HPAMP0.000––
GPU_ALT_VREF0.710––
GPU_BUFRSTN0.776––
GPU_FBA_DEBUG00.420––
GPU_FBB_DEBUG10.416––
GPU_GOOD0.552––
GPU_IFPA_IOVDD0.565––
GPU_IFPAB_PLLVDD0.310––
GPU_IFPB_IOVDD0.579––
GPU_IFPC_IOVDD0.281––
GPU_IFPX_PLLVDD0.577––
GPU_JTAG_TCK0.785––
GPU_JTAG_TDI0.785––
GPU_JTAG_TDO0.784––
GPU_JTAG_TMS0.787––
GPU_JTAG_TRST_L0.842––
GPU_MLS_STRAP00.775––
GPU_MLS_STRAP20.781––
GPU_MLS_STRAP30.776––
GPU_MLS_STRAP40.782––
GPU_OSC_27M_XTALIN0.837––
GPU_OSC_27M_XTALOUT0.818––
GPU_PEX_TERMP0.829––
GPU_PRESENT_DRAIN0.593––
GPU_PRESENT_R1.350––
GPU_RESET_L0.459––
GPU_RESET_R_L0.459––
GPU_ROM_SCLK0.780––
GPU_ROM_SI0.783––
GPU_ROM_SO0.780––
GPU_SMB_CLK0.623––
GPU_SMB_DAT0.623––
GPU_SSC_SMB_CLK0.711––
GPU_SSC_SMB_DAT0.720––
GPU_TESTMODE0.842––
GPU_VCORE_VID00.512––
GPU_VCORE_VID10.511––
GPU_VCORE_VID20.509––
GPU_VCORE_VID30.514––
GPU_VCORE_VID40.542––
GPU_VCORE_VID50.542––
GPU_XTAL_SSIN0.776––
HDA_BIT_CLK0.511––
HDA_BIT_CLK_R0.478––
HDA_RST_L0.496––
HDA_RST_R_L0.466––
HDA_SDIN00.460––
HDA_SDOUT0.502––
HDA_SDOUT_R0.467––
HDA_SYNC0.497––
HDA_SYNC_R0.463––
HDD_OOB_1V00_REF0.708––
HDD_OOB1_D2R_L0.627––
HDD_PWR_EN0.536––
HS_HDET2.018––
HS_MIC_BIAS0.572––
HS_RX_BP0.611––
HS_SW_DET0.563––
I2C_CAMSENSOR_SCL0.524––
I2C_CAMSENSOR_SDA0.524––
I2C_TBTRTR_SCL0.670––
I2C_TBTRTR_SDA0.670––
ICT_JTAG_EN0.994––
IFPD_RSET0.805––
ISNS_CPUVCC0.743––
ISNS_CPUVCC_FB0.684––
ISNS_CPUVCC_FB_R0.675––
ISNS_GPUCORE_ALT0.732––
ISNS_GPUCORE_FB0.691––
ISNS_GPUCORE_R0.676––
ISNS_HDDS00.000––
ISNS_HDDS0_ROL––
ISNS_P1V5S00.743––
ISNS_P1V5S0_R0.716––
ISNS_P12VG3H0.743––
ISNS_P12VG3H_R0.709––
ISNS_P12VS0_FBVDDQ0.749––
ISNS_P12VS0_GPUCORE0.745––
ISNS_P12VS0_GPUCORE_R0.712––
ISNS_SSDS00.747––
ISNS_SSDS0_R0.671––
ISNS_VDDQS3_DDR0.743––
ISNS_VDDQS3_DDR_R0.715––
ISOLATE_CPU_MEM_L0.565––
ISOLATE_MEM_5V0.587––
ITS_PLUGGED_IN1.140––
JTAG_ISP_TCK0.527––
JTAG_ISP_TDI0.555––
JTAG_ISP_TDO0.550––
JTAG_TBT_TCK0.566––
JTAG_TBT_TDI0.645––
JTAG_TBT_TDO0.644––
JTAG_TBT_TMS0.645––
JTAG_TBT_TMS_PCH0.537––
LCD_SHOULD_ON_R1.136––
LDO_DDRVTTS0_SNS0.544––
LED_RETURN_11.121––
LED_RETURN_21.090––
LED_RETURN_31.100––
LED_RETURN_41.125––
LED_RETURN_51.106––
LED_RETURN_61.132––
LGND_BKLT0.000––
LPC_AD_R<0>0.558––
LPC_AD_R<1>0.557––
LPC_AD_R<2>0.560––
LPC_AD_R<3>0.563––
LPC_AD<0>0.596––
LPC_AD<1>0.593––
LPC_AD<2>0.595––
LPC_AD<3>0.595––
LPC_CLK33M_LPCPLUS0.654––
LPC_CLK33M_LPCPLUS_R0.621––
LPC_CLK33M_SMC0.643––
LPC_CLK33M_SMC_R0.614––
LPC_FRAME_L0.588––
LPC_FRAME_R_L0.558––
LPC_PWRDWN_L0.663––
LPC_SERIRQ0.697––
LVDS_BKLT_PWM_RC0.569––
MAX9119_POS0.698––
MAX97220_C1N0.902––
MAX97220_C1P0.674––
MAX97220_INL_NOL––
MAX97220_INL_POL––
MAX97220_INR_NOL––
MAX97220_INR_POL––
MAX97220_OUTLOL––
MAX97220_OUTL_ZOBEL0.036––
MAX97220_OUTROL––
MAX97220_OUTR_ZOBEL0.037––
MAX97220_PVSS1.249––
MAX97220_SHDN_L0.622––
MEM_A_A<1>0.242––
MEM_A_A<6>0.242––
MEM_A_A<7>0.240––
MEM_A_A<8>0.249––
MEM_A_A<9>0.240––
MEM_A_A<15>0.243––
MEM_A_CAS_L0.250––
MEM_A_CLK_N<1>0.283––
MEM_A_CLK_P<0>0.287––
MEM_A_CS_L<1>0.246––
MEM_A_DQ<1>0.285––
MEM_A_DQ<2>0.278––
MEM_A_DQ<3>0.280––
MEM_A_DQ<4>0.281––
MEM_A_DQ<7>0.277––
MEM_A_DQ<9>0.280––
MEM_A_DQ<13>0.281––
MEM_A_DQ<14>0.282––
MEM_A_DQ<15>0.277––
MEM_A_DQ<16>0.278––
MEM_A_DQ<17>0.277––
MEM_A_DQ<18>0.280––
MEM_A_DQ<21>0.281––
MEM_A_DQ<22>0.280––
MEM_A_DQ<23>0.282––
MEM_A_DQ<24>0.283––
MEM_A_DQ<26>0.287––
MEM_A_DQ<29>0.285––
MEM_A_DQ<31>0.280––
MEM_A_DQ<32>0.291––
MEM_A_DQ<34>0.290––
MEM_A_DQ<39>0.290––
MEM_A_DQ<42>0.289––
MEM_A_DQ<45>0.291––
MEM_A_DQ<46>0.288––
MEM_A_DQ<48>0.290––
MEM_A_DQ<50>0.292––
MEM_A_DQ<51>0.290––
MEM_A_DQ<52>0.289––
MEM_A_DQ<53>0.289––
MEM_A_DQ<55>0.289––
MEM_A_DQ<57>0.289––
MEM_A_DQ<58>0.285––
MEM_A_DQ<61>0.287––
MEM_A_DQ<62>0.287––
MEM_A_DQ<63>0.289––
MEM_A_DQS_N<0>0.280––
MEM_A_DQS_N<4>0.290––
MEM_A_DQS_P<1>0.280––
MEM_A_DQS_P<2>0.282––
MEM_A_DQS_P<3>0.281––
MEM_A_DQS_P<5>0.291––
MEM_A_DQS_P<7>0.289––
MEM_A_SA<0>OL––
MEM_A_SA<1>OL––
MEM_B_A<2>0.244––
MEM_B_A<3>0.243––
MEM_B_A<4>0.242––
MEM_B_A<10>0.241––
MEM_B_A<11>0.240––
MEM_B_A<12>0.240––
MEM_B_A<13>0.242––
MEM_B_BA<0>0.242––
MEM_B_BA<1>0.243––
MEM_B_BA<2>0.240––
MEM_B_CKE<0>0.238––
MEM_B_CKE<1>0.239––
MEM_B_CLK_N<1>0.287––
MEM_B_CS_L<1>0.245––
MEM_B_DQ<1>0.278––
MEM_B_DQ<2>0.278––
MEM_B_DQ<4>0.279––
MEM_B_DQ<6>0.276––
MEM_B_DQ<7>0.279––
MEM_B_DQ<9>0.278––
MEM_B_DQ<11>0.280––
MEM_B_DQ<12>0.279––
MEM_B_DQ<14>0.274––
MEM_B_DQ<18>0.277––
MEM_B_DQ<21>0.277––
MEM_B_DQ<23>0.578––
MEM_B_DQ<24>0.280––
MEM_B_DQ<26>0.279––
MEM_B_DQ<27>0.280––
MEM_B_DQ<29>0.280––
MEM_B_DQ<30>0.280––
MEM_B_DQ<33>0.290––
MEM_B_DQ<34>0.286––
MEM_B_DQ<39>0.284––
MEM_B_DQ<41>0.291––
MEM_B_DQ<42>0.290––
MEM_B_DQ<43>0.289––
MEM_B_DQ<44>0.286––
MEM_B_DQ<47>0.285––
MEM_B_DQ<49>0.289––
MEM_B_DQ<50>0.288––
MEM_B_DQ<51>0.287––
MEM_B_DQ<52>0.285––
MEM_B_DQ<54>0.284––
MEM_B_DQ<56>0.286––
MEM_B_DQ<58>0.289––
MEM_B_DQ<61>0.285––
MEM_B_DQ<62>0.283––
MEM_B_DQS_N<4>0.292––
MEM_B_DQS_N<5>0.285––
MEM_B_DQS_N<6>0.289––
MEM_B_DQS_P<0>0.277––
MEM_B_DQS_P<1>0.280––
MEM_B_DQS_P<2>0.277––
MEM_B_DQS_P<3>0.280––
MEM_B_DQS_P<7>0.282––
MEM_B_ODT<1>0.246––
MEM_B_RAS_L0.243––
MEM_B_SA<0>OL––
MEM_B_SA<1>OL––
MEM_RESET_L0.818––
MEM_VDD_SEL_1V5_L0.555––
MEM_VREFCA_A_RC0.026––
MEM_VREFCA_B_RC0.026––
MEMRESET_ISOL_LS5V_L0.596––
MIPI_RESISTOR0.791––
MULTI_STRAP_REF0.834––
MUTE_CONTROLOL––
NCOL––
P1V2_S4_EN0.782––
P1V5_S0_FET_GATE0.683––
P1V8_S4_EN0.782––
P3V3_S0_OOBOL––
P3V3_S0_SSD_FET_RAMP0.657––
P3V3ENET_SSOL––
P3V42G3H_FB0.720––
P3V42G3H_SHDN_L0.719––
P3V42G3H_SW0.328––
P5V_S0_FET_RAMP0.660––
P5V_S0_HDD_FET_RAMP0.734––
P12V_S0_FET_GATE0.383––
P12V_S0_FET_GATE_R0.683––
PCA9557D_RESET_L0.592––
PCH_A20GATE0.613––
PCH_CAM_EXT_BOOT_L0.550––
PCH_CAM_EXT_BOOT_R_L0.581––
PCH_CAM_RESET0.549––
PCH_CAM_RESET_R0.579––
PCH_CLK32K_RTCX10.475––
PCH_CLK32K_RTCX20.816––
PCH_CLK32K_RTCX2_R0.806––
PCH_CLK33M_PCIIN0.668––
PCH_CLK33M_PCIOUT0.627––
PCH_CLK96M_DOTN0.790––
PCH_CLK96M_DOTP0.790––
PCH_CLK100M_SATAN0.799––
PCH_CLK100M_SATAP0.799––
PCH_CLKIN_GNDN0.790––
PCH_CLKIN_GNDP0.791––
PCH_CLKRQ3_L_GPIO250.545––
PCH_CLKRQ5_L_GPIO440.600––
PCH_CLKRQ7_L_GPIO460.606––
PCH_DMI_RCOMP0.746––
PCH_DSWVRMEN0.797––
PCH_FDI_RCOMP0.744––
PCH_GPIO100.539––
PCH_GPIO160.581––
PCH_GPIO310.681––
PCH_GPIO320.600––
PCH_GPIO360.549––
PCH_GPIO410.542––
PCH_GPIO420.542––
PCH_GPIO490.594––
PCH_GPIO720.555––
PCH_INTRUDER_L0.800––
PCH_INTVRMEN_L0.801––
PCH_PCIE_RCOMP0.787––
PCH_PECI0.588––
PCH_PROCPWRGD0.386––
PCH_RCIN_L0.824––
PCH_SATA_RCOMP0.756––
PCH_SATALED_L0.750––
PCH_SMBALERT_L0.666––
PCH_SML0ALERT_L0.668––
PCH_SML1ALERT_L0.666––
PCH_SPKR0.611––
PCH_SRTCRST_L0.798––
PCH_STRP_TOPBLK_SWP_L0.495––
PCH_SUSACK_L0.558––
PCH_SUSWARN_L0.558––
PCH_TD_IREF0.791––
PCH_USB_RBIAS0.025––
PCI_INTA_L0.745––
PCI_INTB_L0.737––
PCI_INTC_L0.744––
PCI_INTD_L0.748––
PCIE_AP_D2R_N0.383––
PCIE_AP_D2R_P0.385––
PCIE_AP_R2D_C_N0.386––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_N0.292––
PCIE_CLK100M_AP_P0.291––
PCIE_CLK100M_ENET_N0.293––
PCIE_CLK100M_ENET_P0.293––
PCIE_CLK100M_PCHN0.790––
PCIE_CLK100M_PCHP0.791––
PCIE_CLK100M_SSD_N0.288––
PCIE_CLK100M_SSD_P0.294––
PCIE_ENET_D2R_C_N0.515––
PCIE_ENET_D2R_C_P0.516––
PCIE_ENET_D2R_N0.386––
PCIE_ENET_D2R_P0.386––
PCIE_ENET_R2D_C_N0.390––
PCIE_ENET_R2D_C_P0.390––
PCIE_ENET_R2D_N0.500––
PCIE_ENET_R2D_P0.500––
PCIE_TBT_D2R_N<0>0.379––
PCIE_TBT_D2R_N<1>0.382––
PCIE_TBT_D2R_N<2>0.379––
PCIE_TBT_D2R_P<0>0.385––
PCIE_TBT_D2R_P<1>0.388––
PCIE_TBT_D2R_P<2>0.382––
PCIE_TBT_D2R_P<3>0.380––
PCIE_TBT_R2D_C_N<0>0.389––
PCIE_TBT_R2D_C_N<1>0.386––
PCIE_TBT_R2D_C_N<2>0.387––
PCIE_TBT_R2D_C_N<3>0.384––
PCIE_TBT_R2D_C_P<0>0.387––
PCIE_TBT_R2D_C_P<1>0.387––
PCIE_TBT_R2D_C_P<2>0.387––
PCIE_TBT_R2D_C_P<3>0.391––
PCIE_TBT_R2D_N<0>0.395––
PCIE_TBT_R2D_N<1>0.395––
PCIE_TBT_R2D_N<2>0.395––
PCIE_TBT_R2D_N<3>0.394––
PCIE_TBT_R2D_P<0>0.394––
PCIE_TBT_R2D_P<1>0.395––
PCIE_TBT_R2D_P<2>0.392––
PCIE_TBT_R2D_P<3>0.391––
PCIE_WAKE_L0.516––
PEG_CLK100M_N0.293––
PEG_CLK100M_P0.296––
PEG_CLKREQ_L0.576––
PEG_D2R_C_N<0>0.365––
PEG_D2R_C_N<1>0.358––
PEG_D2R_C_N<2>0.366––
PEG_D2R_C_N<3>0.358––
PEG_D2R_C_N<4>0.367––
PEG_D2R_C_N<5>0.360––
PEG_D2R_C_N<6>0.363––
PEG_D2R_C_N<7>0.358––
PEG_D2R_C_N<8>0.367––
PEG_D2R_C_N<9>0.359––
PEG_D2R_C_N<10>0.359––
PEG_D2R_C_N<11>0.357––
PEG_D2R_C_N<12>0.358––
PEG_D2R_C_N<13>0.357––
PEG_D2R_C_N<14>0.358––
PEG_D2R_C_N<15>0.356––
PEG_D2R_C_P<0>0.366––
PEG_D2R_C_P<1>0.359––
PEG_D2R_C_P<2>0.366––
PEG_D2R_C_P<3>0.358––
PEG_D2R_C_P<4>0.368––
PEG_D2R_C_P<5>0.360––
PEG_D2R_C_P<6>0.365––
PEG_D2R_C_P<7>0.359––
PEG_D2R_C_P<8>0.370––
PEG_D2R_C_P<9>0.359––
PEG_D2R_C_P<10>0.359––
PEG_D2R_C_P<11>0.358––
PEG_D2R_C_P<12>0.358––
PEG_D2R_C_P<13>0.357––
PEG_D2R_C_P<14>0.359––
PEG_D2R_C_P<15>0.357––
PEG_D2R_N<0>OL––
PEG_D2R_N<1>0.317––
PEG_D2R_N<2>OL––
PEG_D2R_N<3>0.316––
PEG_D2R_N<4>OL––
PEG_D2R_N<5>0.315––
PEG_D2R_N<6>OL––
PEG_D2R_N<7>0.313––
PEG_D2R_N<8>OL––
PEG_D2R_N<9>0.314––
PEG_D2R_N<10>0.314––
PEG_D2R_N<11>0.314––
PEG_D2R_N<12>0.313––
PEG_D2R_N<13>0.311––
PEG_D2R_N<14>0.311––
PEG_D2R_N<15>0.311––
PEG_D2R_P<0>OL––
PEG_D2R_P<1>0.316––
PEG_D2R_P<2>OL––
PEG_D2R_P<3>0.315––
PEG_D2R_P<4>OL––
PEG_D2R_P<5>0.315––
PEG_D2R_P<6>OL––
PEG_D2R_P<7>0.313––
PEG_D2R_P<8>OL––
PEG_D2R_P<9>0.314––
PEG_D2R_P<10>0.314––
PEG_D2R_P<11>0.314––
PEG_D2R_P<12>0.312––
PEG_D2R_P<13>0.312––
PEG_D2R_P<14>0.130––
PEG_D2R_P<15>0.311––
PEG_R2D_C_N<0>OL––
PEG_R2D_C_N<1>OL––
PEG_R2D_C_N<2>OL––
PEG_R2D_C_N<3>OL––
PEG_R2D_C_N<4>OL––
PEG_R2D_C_N<5>OL––
PEG_R2D_C_N<6>OL––
PEG_R2D_C_N<7>OL––
PEG_R2D_C_N<8>OL––
PEG_R2D_C_N<9>OL––
PEG_R2D_C_N<10>OL––
PEG_R2D_C_N<11>OL––
PEG_R2D_C_N<12>OL––
PEG_R2D_C_N<13>OL––
PEG_R2D_C_N<14>OL––
PEG_R2D_C_N<15>OL––
PEG_R2D_C_P<0>OL––
PEG_R2D_C_P<1>OL––
PEG_R2D_C_P<2>OL––
PEG_R2D_C_P<3>OL––
PEG_R2D_C_P<4>OL––
PEG_R2D_C_P<5>OL––
PEG_R2D_C_P<6>OL––
PEG_R2D_C_P<7>OL––
PEG_R2D_C_P<8>OL––
PEG_R2D_C_P<9>OL––
PEG_R2D_C_P<10>OL––
PEG_R2D_C_P<11>OL––
PEG_R2D_C_P<12>OL––
PEG_R2D_C_P<13>OL––
PEG_R2D_C_P<14>OL––
PEG_R2D_C_P<15>OL––
PEG_R2D_N<0>0.394––
PEG_R2D_N<1>0.394––
PEG_R2D_N<2>0.393––
PEG_R2D_N<3>0.394––
PEG_R2D_N<4>0.395––
PEG_R2D_N<5>0.395––
PEG_R2D_N<6>0.393––
PEG_R2D_N<7>0.394––
PEG_R2D_N<8>0.394––
PEG_R2D_N<9>0.394––
PEG_R2D_N<10>0.393––
PEG_R2D_N<11>0.395––
PEG_R2D_N<12>0.395––
PEG_R2D_N<13>0.394––
PEG_R2D_N<14>0.396––
PEG_R2D_N<15>0.397––
PEG_R2D_P<0>0.396––
PEG_R2D_P<1>0.395––
PEG_R2D_P<2>0.394––
PEG_R2D_P<3>0.393––
PEG_R2D_P<4>0.394––
PEG_R2D_P<5>0.394––
PEG_R2D_P<6>0.392––
PEG_R2D_P<7>0.394––
PEG_R2D_P<8>0.394––
PEG_R2D_P<9>0.395––
PEG_R2D_P<10>0.395––
PEG_R2D_P<11>0.393––
PEG_R2D_P<12>0.393––
PEG_R2D_P<13>0.394––
PEG_R2D_P<14>0.394––
PEG_R2D_P<15>0.393––
PGND_BKLT0.000––
PLT_RESET_L0.556––
PLT_RST_BUF_L0.423––
PM_CLK32K_SUSCLK_R0.697––
PM_CLKRUN_L0.761––
PM_DSW_PWRGD0.701––
PM_EN_ENET_L0.578––
PM_EN_FET_P3V3_S00.565––
PM_EN_FET_P3V3_S40.502––
PM_EN_FET_P5V_S00.448––
PM_EN_FET_P12V_S00.582––
PM_EN_FET_REG_P1V5_S00.546––
PM_EN_LDO_DDRVTT_S00.542––
PM_EN_REG_CPUVCC_S00.540––
PM_EN_REG_GPU_VDDQ_S00.517––
PM_EN_REG_GPUCORE_S00.541––
PM_EN_REG_P1V05_S00.553––
PM_EN_REG_P1V05_S0_R0.554––
PM_EN_REG_P3V3_S50.518––
PM_EN_REG_P5V_S40.508––
PM_EN_REG_VDDQ_S30.504––
PM_EN_S0_R0.492––
PM_EN_S40.505––
PM_EN_USB_PWR0.447––
PM_MEM_PWRGD0.513––
PM_PCH_PWROK0.501––
PM_PCH_SYS_PWROK0.739––
PM_PCH_SYS_PWROK_R0.542––
PM_PGOOD_FET_P3V3_S00.544––
PM_PGOOD_FET_P5V_S00.564––
PM_PGOOD_FET_P12V_S00.548––
PM_PGOOD_FET_REG_P1V5_S00.656––
PM_PGOOD_REG_CPUVCC_S00.633––
PM_PGOOD_REG_GPU_P1V35_S00.547––
PM_PGOOD_REG_GPU_VDDQ_S00.546––
PM_PGOOD_REG_P1V05_S00.536––
PM_PGOOD_REG_P3V3_S50.536––
PM_PGOOD_REG_P5V_S40.449––
PM_PGOOD_REG_VDDQ_S30.572––
PM_PGOOD_SLP_S3_P1V05_S00.692––
PM_PWRBTN_L0.642––
PM_RSMRST_PCH_L0.536––
PM_RSMRST_PCH_L_R0.536––
PM_SLP_S3_BUF_L0.566––
PM_SLP_S3_L0.532––
PM_SLP_S4_L0.657––
PM_SLP_S5_L0.654––
PM_SLP_SUS_L0.667––
PM_SYNC0.390––
PM_SYSRST_L0.672––
PM_THRMTRIP_L0.136––
PM_THRMTRIP_L_R0.524––
PP1V2_ENET_INTREG0.297––
PP1V2_ENET_PHY_AVDDL0.297––
PP1V2_ENET_PHY_GPHYPLL0.297––
PP1V2_ENET_PHY_PCIEPLL0.297––
PP1V2_G3H_SMC_VDDC0.520––
PP1V2_S4_CAMERA0.337––
PP1V2_S4_CAMFILT0.348––
PP1V2_S4_F_R0.337––
PP1V05_GPU_FB_DLL_AVDD0.089––
PP1V05_GPU_FB_PLL_AVDD0.090––
PP1V05_GPU_IFPD_IOVDD0.090––
PP1V05_GPU_IFPEF_IOVDD0.090––
PP1V05_GPU_PLLVDD0.090––
PP1V05_GPU_SP_PLLVDD0.089––
PP1V05_S00.079–78.500R
PP1V5_S00.142–140.800
PP1V5_S0_PCH0.142–140.800
PP1V05_S0_PCH_VCC_CLK_F0.079––
PP1V05_TBTCIO0.176––
PP1V05_TBTLC0.138––
PP1V8_S4_CAMERA0.433––
PP1V8_S4_CAMERA_F0.433––
PP3V3_DMIC_CONN0.358––
PP3V3_ENET0.366––
PP3V3_ENET_PHY_AVDDH0.366––
PP3V3_ENET_PHY_BIASVDDH0.366––
PP3V3_G30.573––
PP3V3_G3H_AVREF_SMC0.610––
PP3V3_G3H_BT_FLT0.515––
PP3V3_G3H_SMC_VDDA0.329––
PP3V3_GPU_IFPX_PLLVDD0.364––
PP3V3_S00.358––
PP3V3_S0_BKLT_VDDIO_R0.359––
PP3V3_S0_SSD0.453––
PP3V3_S0_SSD_FLT0.453––
PP3V3_S0_SW_SD_PWR0.564––
PP3V3_S3_VREFMRGN0.341––
PP3V3_S40.332––
PP3V3_S4_ALS_F0.332––
PP3V3_S4_AP_FLT0.501––
PP3V3_S4_CAMFILT0.332––
PP3V3_S50.145––
PP3V3_S5_XDP_R0.107––
PP3V3_TBTLC0.415––
PP3V3R1V8_ENET_LR_OUT0.550––
PP3V3RHV_SW_TBTAPWR0.562––
PP3V3RHV_SW_TBTBPWR0.565––
PP3V42_G3H0.329––
PP3V42_G3H_SMC_SPVSR0.375––
PP4V5_AUDIO_ANALOG0.503––
PP5V_AUDIO_HPAMP0.410––
PP5V_S00.410––
PP5V_S0_BKLT_R0.408––
PP5V_S0_GFXIMVP_VDD0.409––
PP5V_S0_HDD0.600––
PP5V_S40.158––
PP5V_S4_CAMERA_F0.156––
PP5V_S4_EXTA_F0.526––
PP5V_S4_EXTA_ILIM0.526––
PP5V_S4_EXTB_F0.525––
PP5V_S4_EXTB_ILIM0.525––
PP5V_S4_EXTC_F0.525––
PP5V_S4_EXTC_ILIM0.525––
PP5V_S4_EXTD_F0.523––
PP5V_S4_EXTD_ILIM0.523––
PP5V_S50.457––
PP12V_ACDC0.568––
PP12V_BKLT_FUSED0.459––
PP12V_BKLT_SNS0.459––
PP12V_G3H0.568––
PP12V_LCD0.464––
PP12V_LCD_F0.465––
PP12V_S00.459––
PP12V_S0_BKLT_FILT0.459––
PP12V_S0_BKLT_PWR0.169––
PP12V_S0_BKLT_PWR_R0.167––
PP12V_S0_CPUVCC_FLT0.463––
PP12V_S0_FAN_0_FILT0.459––
PP12V_S0_FBVDDQ0.463––
PP12V_S0_GPUCORE0.461––
PP12V_S50.541––
PPCPUVCC_S0_CPU0.018–17.900R
PPCPUVCC_S0_SENSE_1––17.900R
PPCPUVCC_S0_SENSE_2––17.900R
PPCPUVCC_S0_SENSE_30.018–17.900R
PPDDRVTT_S00.544––
PPHDD_S00.600––
PPHV_SW_TBTAPWR0.562––
PPHV_SW_TBTBPWR0.565––
PPSSD_S00.453––
PPVBATT_G3_RTC_ROL––
PPVCCIO_S0_CPU0.022–21.400R
PPVCOMP_S0_CPU0.044––
PPVCORE_S0_GFX_PH10.036–33.900R
PPVCORE_S0_GFX_PH20.036–33.900R
PPVCORE_S0_GPU0.036–33.900R
PPVDDQ_S0_GPU0.088––
PPVDDQ_S30.321–318.000
PPVDDQ_S3_DDR––318.000
PPVIN_S0_GFXIMVP_R0.469––
PPVOUT_S0_PCH_DCPRTC0.724––
PPVOUT_S5_PCH_DCPSUSBYP0.419––
PPVOUT_S5_PCH_DCPSUSBYP_R0.414––
PPVREF_S3_MEM_VREFCA_A0.583––
PPVREF_S3_MEM_VREFCA_B0.583––
PPVREF_S3_MEM_VREFDQ_A0.582––
PPVREF_S3_MEM_VREFDQ_B0.586––
PU_U85000.715––
PWR_BTN_R0.850––
Q6170_P_GOL––
Q6170_P_SOL––
REG_BOOT_CPUVCC_10.606––
REG_BOOT_CPUVCC_1_RC0.606––
REG_BOOT_CPUVCC_20.608––
REG_BOOT_CPUVCC_2_RC0.608––
REG_BOOT_CPUVCC_30.607––
REG_BOOT_CPUVCC_3_RC0.607––
REG_BOOT_GPUCORE_10.548––
REG_BOOT_GPUCORE_1_RC0.548––
REG_BOOT_GPUCORE_20.549––
REG_BOOT_GPUCORE_2_RC0.549––
REG_BOOT_GPUVDDQ0.581––
REG_BOOT_GPUVDDQ_RC0.582––
REG_BOOT_P1V05S00.578––
REG_BOOT_P1V05S0_RC0.578––
REG_BOOT_P3V3S50.596––
REG_BOOT_P3V3S5_RC0.596––
REG_BOOT_P5VS40.600––
REG_BOOT_P5VS4_RC0.600––
REG_BOOT_VDDQS30.616––
REG_BOOT_VDDQS3_RC0.616––
REG_CPUVCC_COMP0.632––
REG_CPUVCC_DVC0.631––
REG_CPUVCC_FB0.572––
REG_CPUVCC_FDVID0.632––
REG_CPUVCC_HFCOMP0.608––
REG_CPUVCC_IMON0.621––
REG_CPUVCC_IMON_R0.677––
REG_CPUVCC_IMX0.621––
REG_CPUVCC_MEMVRSEL0.000––
REG_CPUVCC_NPSI0.629––
REG_CPUVCC_PSICOMP0.589––
REG_CPUVCC_RGND0.013–12.900R
REG_CPUVCC_RSET0.628––
REG_CPUVCC_TM0.606––
REG_CPUVCC_TMX0.629––
REG_CPUVCC_VIN0.661––
REG_CPUVCC_VRHOT_L0.074–73.200R
REG_CPUVCC_VSEN0.031–30.000R
REG_GPUCORE_COMP0.544––
REG_GPUCORE_COMP_R0.544––
REG_GPUCORE_DPSLP_EN0.547––
REG_GPUCORE_FB0.337––
REG_GPUCORE_FB_GND_ROL––
REG_GPUCORE_FB_SNS_R0.387––
REG_GPUCORE_FB20.544––
REG_GPUCORE_ISNS1_N0.036–33.900R
REG_GPUCORE_ISNS1_P0.036–33.900R
REG_GPUCORE_ISNS2_N0.036–33.900R
REG_GPUCORE_ISNS2_P0.036–33.900R
REG_GPUCORE_ISUMN0.034––
REG_GPUCORE_ISUMN_R0.396––
REG_GPUCORE_ISUMP0.460––
REG_GPUCORE_ISUMP_COL––
REG_GPUCORE_NTC0.543––
REG_GPUCORE_PSI_R_L0.512––
REG_GPUCORE_RBIAS0.546––
REG_GPUCORE_VR_TT_L0.500––
REG_GPUCORE_VW0.544––
REG_GPUVDDQ_FB0.535––
REG_GPUVDDQ_FSEL0.000––
REG_GPUVDDQ_OCSET0.551––
REG_GPUVDDQ_RTN0.540––
REG_GPUVDDQ_SET00.552––
REG_GPUVDDQ_SET10.549––
REG_GPUVDDQ_SET1_R0.549––
REG_GPUVDDQ_SREF0.548––
REG_GPUVDDQ_VO0.550––
REG_ISEN_GPUCORE_10.539––
REG_ISEN_GPUCORE_20.540––
REG_ISENVCC_1_N––17.900R
REG_ISENVCC_1_NR0.581––
REG_ISENVCC_1_P––17.900R
REG_ISENVCC_2_N––17.900R
REG_ISENVCC_2_NR0.580––
REG_ISENVCC_2_P––17.900R
REG_ISENVCC_3_N0.018–17.900R
REG_ISENVCC_3_NR0.581––
REG_ISENVCC_3_P0.018–17.900R
REG_LGATE_CPUVCC_10.444––
REG_LGATE_CPUVCC_20.440––
REG_LGATE_CPUVCC_30.444––
REG_LGATE_GPUCORE_10.469––
REG_LGATE_GPUCORE_20.446––
REG_LGATE_GPUVDDQ0.458––
REG_LGATE_P1V05S00.465––
REG_LGATE_P3V3S50.466––
REG_LGATE_P5VS40.468––
REG_P1V05S0_FB0.528––
REG_P1V05S0_FSEL0.553––
REG_P1V05S0_OCSET0.548––
REG_P1V05S0_RTN0.530––
REG_P1V05S0_SREF0.550––
REG_P1V05S0_VO0.547––
REG_P3V3S5_FB0.532––
REG_P3V3S5_FSET0.537––
REG_P3V3S5_ISEN0.538––
REG_P3V3S5_OCSET0.537––
REG_P3V3S5_VOUT0.140––
REG_P3V3S5_VOUT_R1.122––
REG_P5VS4_FB0.535––
REG_P5VS4_FSET0.537––
REG_P5VS4_ISEN0.543––
REG_P5VS4_OCSET0.536––
REG_P5VS4_VOUT0.154––
REG_P5VS4_VOUT_R1.134––
REG_PHASE_CPUVCC_1––17.900R
REG_PHASE_CPUVCC_2––17.900R
REG_PHASE_CPUVCC_3––17.900R
REG_PHASE_GPUCORE_10.036––
REG_PHASE_GPUCORE_20.036––
REG_PHASE_GPUVDDQ0.088–87.000R
REG_PHASE_P1V05S00.078–77.400R
REG_PHASE_P1V05S0_L0.079––
REG_PHASE_P3V3S50.145––
REG_PHASE_P5VS40.158––
REG_PHASE_VDDQS30.320––
REG_PHASE_VDDQS3_L0.321––
REG_PVCC_U74000.410––
REG_PVCC_U77500.412––
REG_PWM_CPUVCC_10.533––
REG_PWM_CPUVCC_1_R0.534––
REG_PWM_CPUVCC_20.533––
REG_PWM_CPUVCC_2_R0.532––
REG_PWM_CPUVCC_30.532––
REG_PWM_CPUVCC_3_R0.532––
REG_PWM_CPUVCC_4_R0.409––
REG_SNUBBER_CPUVCC_1OL––
REG_SNUBBER_CPUVCC_2OL––
REG_SNUBBER_CPUVCC_3OL––
REG_SNUBBER_GPUCORE_1OL––
REG_SNUBBER_GPUCORE_2OL––
REG_SNUBBER_P1V05S0OL––
REG_SNUBBER_P3V3S5OL––
REG_SNUBBER_P5VS4OL––
REG_SNUBBER_VDDQS3OL––
REG_TD_10.409––
REG_TD_20.409––
REG_TD_30.412––
REG_U7600_FCCM0.544––
REG_U7600_FCCM_ROL––
REG_UGATE_CPUVCC_10.635––
REG_UGATE_CPUVCC_20.631––
REG_UGATE_CPUVCC_30.632––
REG_UGATE_GPUCORE_10.502––
REG_UGATE_GPUCORE_20.504––
REG_UGATE_P1V05S00.605––
REG_UGATE_P1V05S0_R0.605––
REG_UGATE_P3V3S50.593––
REG_UGATE_P5VS40.597––
REG_UGATE_VDDQS30.780––
REG_UGATE_VDDQS3_R0.604––
REG_V5IN_U73000.159––
REG_VCC_U70000.410––
REG_VCC_U74000.418––
REG_VCC_U77500.419––
REG_VCC1_U76000.511––
REG_VCC2_U76000.458––
REG_VDDQS3_MODE0.488––
REG_VDDQS3_REFIN0.688––
REG_VDDQS3_TRIP0.751––
REG_VDDQS3_VDDQSNS0.318––
REG_VDDQS3_VREF0.631––
REG_VDDQS3_VTTREF0.493––
REG_VIN_U76000.538––
RTC_RESET_L0.774––
RTC_RESET_L_R0.625––
SATA_HDD_D2R_C_NOL––
SATA_HDD_D2R_C_POL––
SATA_HDD_D2R_N0.384––
SATA_HDD_D2R_P0.386––
SATA_HDD_R2D_C_N0.392––
SATA_HDD_R2D_C_P0.393––
SATA_HDD_R2D_NOL––
SATA_HDD_R2D_POL––
SATA_PWR_L0.609––
SATALED_R_LOL––
SATARDRVR_EN0.602––
SD_DETECT_LVL0.470––
SDCONN_CLK0.590––
SDCONN_CLK_R0.590––
SDCONN_CMD0.584––
SDCONN_DATA<0>0.588––
SDCONN_DATA<1>0.583––
SDCONN_DATA<2>0.588––
SDCONN_DATA<3>0.583––
SDCONN_DATA<4>0.797––
SDCONN_DATA<5>0.796––
SDCONN_DATA<6>0.797––
SDCONN_DATA<7>0.799––
SDCONN_DETECT_L0.471––
SDCONN_ILIM_ROL––
SDCONN_OC_L0.532––
SDCONN_STATE_CHANGE0.460––
SDCONN_WP0.784––
SLG_ENET_RESET_R_L0.460––
SMB_0_S0_CLK0.611––
SMB_0_S0_DATA0.614––
SMB_1_S0_CLK0.646––
SMB_1_S0_DATA0.636––
SMB_2_S4_CLK0.748––
SMB_2_S4_DATA0.747––
SMB_3_CLK0.758––
SMB_3_DATA0.757––
SMB_ALS_F_SCL0.747––
SMB_ALS_F_SDA0.747––
SMB_DP_TCON_SCL2.348––
SMB_DP_TCON_SDA2.365––
SMB_ENET_SCL0.738––
SMB_ENET_SDA0.732––
SMBUS_PCH_CLK0.506––
SMBUS_PCH_DATA0.518––
SMC_ACDC_ID0.750––
SMC_ASSERT_RTCRST0.760––
SMC_CLK32K0.710––
SMC_CPU_CATERR_L0.259––
SMC_DEBUGPRT_EN_L0.572––
SMC_DEBUGPRT_RX_L0.676––
SMC_DEBUGPRT_TX_L0.686––
SMC_DELAYED_PWRGD0.642––
SMC_EXTAL0.780––
SMC_FAN_0_CTL0.748––
SMC_FAN_0_TACH0.751––
SMC_G3_WAKESRC_EN0.750––
SMC_GFX_OVERTEMP0.694––
SMC_GFX_OVERTEMP_L0.718––
SMC_GFX_OVERTEMP_Q0.659––
SMC_GFX_THROTTLE_L0.699––
SMC_LRESET_L0.593––
SMC_MANUAL_RST_L0.680––
SMC_ONOFF_L0.752––
SMC_OOB1_D2R_L0.676––
SMC_OOB1_R2D_L0.751––
SMC_OOB1_R2D_R_L1.279––
SMC_OOB2_D2R_L0.751––
SMC_OOB2_R2D_L0.751––
SMC_PECI_L0.753––
SMC_PECI_L_R0.753––
SMC_PM_G2_EN0.580––
SMC_PM_PCH_SYS_PWROK0.744––
SMC_PME_S4_WAKE_L0.618––
SMC_PROCHOT0.756––
SMC_RESET_L0.592––
SMC_RESET_R_L0.599––
SMC_ROMBOOT1.740––
SMC_RUNTIME_SCI_L0.699––
SMC_RX_L0.756––
SMC_TCK0.747––
SMC_TDI0.747––
SMC_TDO0.747––
SMC_THRMTRIP0.753––
SMC_TMS0.757––
SMC_TOPBLK_SWP_L0.745––
SMC_VCCIO_CPU_DIV20.728––
SMC_WAKE_SCI_L0.556––
SMC_XTAL0.766––
SMC_XTAL_R0.770––
SMIA_CLK_P0.660––
SMIA_DATA_N0.468––
SML_PCH_0_CLK0.645––
SML_PCH_0_DATA0.652––
SNS_ACDC_N0.757––
SNS_ACDC_P0.754––
SNS_GPU_CORE_N0.000––
SNS_GPU_CORE_P0.035––
SNS_GPU_PEX_IOVDD_N0.000––
SNS_GPU_PEX_IOVDD_P0.079–77.900R
SNS_GPUVDDQ_N0.000––
SNS_GPUVDDQ_P0.090–89.000R
SNS_HDD_N0.600––
SNS_HDD_P0.600––
SNS_P1V5S0_N0.142–140.800
SNS_P1V5S0_P0.142–140.800
SNS_P12VG3H_N0.568––
SNS_P12VG3H_P0.568––
SNS_P12VS0_FBVDDQ_N0.463––
SNS_P12VS0_FBVDDQ_P0.463––
SNS_P12VS0_GPUCORE_N0.461––
SNS_P12VS0_GPUCORE_P0.461––
SNS_SSD_N0.453––
SNS_SSD_P0.453––
SNS_T1_1_N0.779––
SNS_T1_1_P0.786––
SNS_T1_2_N0.757––
SNS_T1_2_P0.756––
SNS_T2_1_N0.671––
SNS_T2_2_N0.671––
SNS_T2_2_P0.673––
SNS_T2_3_N0.671––
SNS_T2_DXN0.671––
SNS_VCC_XW_N0.000–1.000R
SNS_VCC_XW_P0.018––
SNS_VDDQS3_DDR_N––318.000
SNS_VDDQS3_DDR_P––318.000
SNS1_ALERT_L0.753––
SPI_ALT_CLK0.613––
SPI_ALT_CS_L0.624––
SPI_ALT_MISO0.533––
SPI_ALT_MOSI0.581––
SPI_CLK0.570––
SPI_CLK_R0.553––
SPI_CS0_L0.582––
SPI_CS0_R_L0.564––
SPI_DESCRIPTOR_OVERRIDE_L0.751––
SPI_DESCRIPTOR_OVERRIDE_R0.789––
SPI_MISO0.508––
SPI_MLB_CLK0.608––
SPI_MLB_CS_L0.612––
SPI_MLB_MISO0.517––
SPI_MLB_MOSI0.541––
SPI_MOSI0.538––
SPI_MOSI_R0.532––
SPI_SMC_CLK0.624––
SPI_SMC_MISO0.546––
SPI_SMC_MOSI0.586––
SPI_WP_L0.704––
SPIROM_USE_MLB0.638––
SPKR_MATCH_DRV0.741––
SPKR_MATCH_DRV_R0.740––
SSD_CLKREQ_L0.537––
SSD_D2R_N<0>0.390––
SSD_D2R_N<1>0.387––
SSD_D2R_P<0>0.385––
SSD_D2R_P<1>0.390––
SSD_EN0.453––
SSD_R2D_C_N<0>OL––
SSD_R2D_C_N<1>OL––
SSD_R2D_C_P<0>OL––
SSD_R2D_C_P<1>OL––
SSD_R2D_N<0>0.385––
SSD_R2D_N<1>0.385––
SSD_R2D_P<0>0.389––
SSD_R2D_P<1>0.386––
SSD_RESET_L0.596––
SYSCLK_CLK25M_ENET0.488––
SYSCLK_CLK25M_ENET_R0.456––
SYSCLK_CLK25M_SB0.434––
SYSCLK_CLK25M_SB_R0.564––
SYSCLK_CLK25M_TBT0.440––
SYSCLK_CLK25M_TBT_R0.669––
SYSCLK_CLK25M_X10.451––
SYSCLK_CLK25M_X20.454––
SYSCLK_CLK25M_X2_R0.453––
TBT_A_BIAS0.770––
TBT_A_CIO_SEL0.563––
TBT_A_CONFIG1_RC0.839––
TBT_A_CONFIG2_RC0.558––
TBT_A_D2R_C_N<0>1.556––
TBT_A_D2R_C_N<1>OL––
TBT_A_D2R_C_P<0>1.818––
TBT_A_D2R_C_P<1>OL––
TBT_A_D2R_N<0>0.398––
TBT_A_D2R_N<1>0.398––
TBT_A_D2R_P<0>0.398––
TBT_A_D2R_P<1>0.398––
TBT_A_D2R1_AUXDDC_N0.701––
TBT_A_D2R1_AUXDDC_P0.704––
TBT_A_DP_PWRDN0.606––
TBT_A_HPD0.841––
TBT_A_HV_EN0.473––
TBT_A_LSRX0.558––
TBT_A_LSRX_UNBUF0.681––
TBT_A_LSTX0.583––
TBT_A_R2D_C_N<0>0.228––
TBT_A_R2D_C_N<1>0.228––
TBT_A_R2D_C_P<0>0.229––
TBT_A_R2D_C_P<1>0.228––
TBT_A_R2D_N<0>OL––
TBT_A_R2D_N<1>OL––
TBT_A_R2D_P<0>OL––
TBT_A_R2D_P<1>OL––
TBT_B_BIAS0.771––
TBT_B_CONFIG1_BUF0.557––
TBT_B_CONFIG1_RC0.841––
TBT_B_CONFIG2_RC0.557––
TBT_B_D2R_C_N<0>OL––
TBT_B_D2R_C_N<1>OL––
TBT_B_D2R_C_P<0>OL––
TBT_B_D2R_C_P<1>OL––
TBT_B_D2R_N<0>0.398––
TBT_B_D2R_N<1>0.398––
TBT_B_D2R_P<0>0.399––
TBT_B_D2R_P<1>0.398––
TBT_B_D2R1_AUXDDC_N0.705––
TBT_B_D2R1_AUXDDC_P0.700––
TBT_B_DP_PWRDN0.611––
TBT_B_HPD0.842––
TBT_B_HV_EN0.474––
TBT_B_LSRX0.552––
TBT_B_R2D_C_N<0>0.228––
TBT_B_R2D_C_N<1>0.270––
TBT_B_R2D_C_P<0>0.229––
TBT_B_R2D_C_P<1>0.229––
TBT_B_R2D_N<0>OL––
TBT_B_R2D_N<1>OL––
TBT_B_R2D_P<0>OL––
TBT_B_R2D_P<1>OL––
TBT_CIO_PLUG_EVENT0.558––
TBT_CIO_PLUG_EVENT_BUF0.683––
TBT_CIO_PLUG_EVENT_ISOL0.533––
TBT_CLKREQ_ISOL_L0.464––
TBT_CLKREQ_L0.447––
TBT_DDC_XBAR_EN_L0.495––
TBT_EN_CIO_PWR0.490––
TBT_EN_CIO_PWR_L0.547––
TBT_EN_LC_ISOL0.471––
TBT_EN_LC_PWR0.557––
TBT_EN_LC_RC1V050.466––
TBT_EN_LC_RC3V30.698––
TBT_GO2SX_BIDIR0.511––
TBT_GPIO_90.421––
TBT_GPIO_140.560––
TBT_MONOBSN0.207––
TBT_MONOBSP0.208––
TBT_PCIE_RESET_L0.463––
TBT_PLT_RST_L0.431––
TBT_PWR_EN0.559––
TBT_PWR_EN_PCH0.606––
TBT_PWR_ON_POC_RST_L0.568––
TBT_RBIAS0.800––
TBT_RSENSE0.004––
TBT_SPI_CLK0.562––
TBT_SPI_CS_L0.665––
TBT_SPI_MISO0.640––
TBT_SW_RESET_L0.658––
TBT_TEST_EN0.004––
TBT_TEST_PWR_GOOD0.003––
TBT_TMU_CLK_IN0.652––
TBT_TMU_CLK_OUT0.560––
TBTACONN_1_COL––
TBTACONN_7_COL––
TBTACONN_20_RC0.574––
TBTAPWRSW_ISET_S00.479––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.479––
TBTAPWRSW_ISET_S3_ROL––
TBTAPWRSW_ISET_V3P30.481––
TBTBCONN_1_COL––
TBTBCONN_7_COL––
TBTBCONN_20_RC0.577––
TBTBPWRSW_ISET_S00.450––
TBTBPWRSW_ISET_S0_ROL––
TBTBPWRSW_ISET_S30.479––
TBTBPWRSW_ISET_S3_ROL––
TBTBPWRSW_ISET_V3P30.482––
TBTPOCRST_CT0.642––
TBTPOCRST_MR_L0.668––
TBTROM_HOLD_L0.745––
TBTROM_WP_L0.743––
TMP006_DRDYOL––
TP_AUD_LAMP_THERM0.618––
TP_CPU_CFG<12>0.264––
TP_CPU_CFG<13>0.262––
TP_CPU_RSVD_TP15OL––
TP_DMIC_SDA20.708––
TP_PCH_SLP_LAN_L0.693––
TP_PCH_SLP_WLAN_L0.688––
TP_PCH_STRP_BBS10.751––
TP_PCH_STRP_ESI_L0.749––
TP_PCI_PME_L0.547––
TP_PM_SLP_A_L0.692––
TP_SMC_MD1OL––
TP_TBT_MONDC00.370––
TP_TBT_MONDC10.371––
TP_TBT_XTAL25OUT0.292––
TP_XDP_PCH_TRST_LOL––
UNCONNECTED_146OL––
UNCONNECTED_147OL––
USB_BT_MUX_N0.788––
USB_BT_MUX_P0.788––
USB_BT_N0.470––
USB_BT_P0.476––
USB_CAMERA_P0.476––
USB_EXTA_0_N0.486––
USB_EXTA_0_P0.484––
USB_EXTA_OC_L0.478––
USB_EXTB_8_N0.484––
USB_EXTB_8_P0.479––
USB_EXTB_OC_L0.490––
USB_EXTC_1_N0.479––
USB_EXTC_1_P0.479––
USB_EXTC_OC_L0.480––
USB_EXTD_9_N0.481––
USB_EXTD_9_P0.481––
USB_EXTD_OC_L0.478––
USB_ILIM10.521––
USB_ILIM1_ROL––
USB2_EXTA_MUXED_N0.651––
USB2_EXTA_MUXED_P0.658––
USB2_EXTA_N0.654––
USB2_EXTA_P0.661––
USB2_EXTB_N0.482––
USB2_EXTB_P0.483––
USB2_EXTC_N0.482––
USB2_EXTC_P0.482––
USB2_EXTD_N0.484––
USB2_EXTD_P0.485––
USB3_EXTA_RX_F_N0.390––
USB3_EXTA_RX_F_P0.390––
USB3_EXTA_RX_N0.390––
USB3_EXTA_RX_P0.390––
USB3_EXTA_TX_C_NOL––
USB3_EXTA_TX_C_POL––
USB3_EXTA_TX_F_NOL––
USB3_EXTA_TX_F_POL––
USB3_EXTB_RX_F_N0.390––
USB3_EXTB_RX_F_P0.390––
USB3_EXTB_RX_N0.390––
USB3_EXTB_RX_P0.390––
USB3_EXTB_TX_C_NOL––
USB3_EXTB_TX_C_POL––
USB3_EXTB_TX_F_NOL––
USB3_EXTB_TX_F_POL––
USB3_EXTC_RX_F_N0.390––
USB3_EXTC_RX_F_P0.390––
USB3_EXTC_RX_N0.390––
USB3_EXTC_RX_P0.390––
USB3_EXTC_TX_C_NOL––
USB3_EXTC_TX_C_POL––
USB3_EXTC_TX_F_NOL––
USB3_EXTC_TX_F_POL––
USB3_EXTC_TX_N0.390––
USB3_EXTD_RX_F_N0.390––
USB3_EXTD_RX_F_P0.390––
USB3_EXTD_RX_N0.390––
USB3_EXTD_RX_P0.390––
USB3_EXTD_TX_C_NOL––
USB3_EXTD_TX_C_POL––
USB3_EXTD_TX_F_NOL––
USB3_EXTD_TX_F_POL––
USB3_EXTD_TX_N0.392––
USB3_EXTD_TX_P0.390––
VBIAS_DAC0.751––
VIDEO_ON0.808––
VIDEO_ON_L0.782––
VIDEO_ON_L_DLY0.807––
VREFMRGN_CA_A_EN_RCOL––
VREFMRGN_CA_A_RDIVOL––
VREFMRGN_CA_ABOL––
VREFMRGN_CA_B_ENOL––
VREFMRGN_CA_B_EN_RCOL––
VREFMRGN_CA_B_RDIVOL––
VREFMRGN_DQ_A_EN_RCOL––
VREFMRGN_DQ_A_RDIVOL––
VREFMRGN_DQ_BOL––
VREFMRGN_DQ_B_ENOL––
VREFMRGN_DQ_B_EN_RCOL––
VREFMRGN_DQ_B_RDIVOL––
VREFMRGN_FRAMEBUF_BUFOL––
VREFMRGN_MEMVREG_BUFOL––
VSNS_CPUVCC0.739––
VSNS_GPUCORE_ALT0.749––
VSNS_HDDS00.600––
VSNS_P1V5S00.750––
VSNS_P1V05S0_PCH0.749––
VSNS_P3V3S50.748––
VSNS_P12VG3H0.742––
VSNS_P12VS0_FBVDDQ0.741––
VSNS_P12VS0_GPUCORE0.746––
VSNS_VDDQS3_DDR0.746––
VTTCLAMP_EN0.596––
VTTCLAMP_L0.544––
WOL_EN0.590––
XDP_BPM_L<0>0.258––
XDP_BPM_L<1>0.259––
XDP_BPM_L<3>OL––
XDP_BPM_L<5>0.263––
XDP_BPM_L<6>0.263––
XDP_BPM_L<7>0.265––
XDP_CPU_PCH_TCK0.897––
XDP_CPU_PCH_TMS0.905––
XDP_CPU_PREQ_L0.257––
XDP_CPU_PRESENT_L1.256––
XDP_CPU_PWRBTN_L0.640––
XDP_CPU_PWRGD1.406––
XDP_CPU_TCK0.052–51.300R
XDP_CPU_TDI0.273––
XDP_CPU_TDO0.128––
XDP_CPU_TDO_PCH_TDI0.875––
XDP_CPU_TMS0.269––
XDP_CPU_TRST_L0.054––
XDP_CPURST_L1.383––
XDP_DA0_USB_EXTA_OC_L0.486––
XDP_DA1_USB_EXTC_OC_L0.490––
XDP_DA2_PCH_GPIO410.540––
XDP_DA3_PCH_GPIO420.542––
XDP_DB0_USB_EXTB_OC_L0.488––
XDP_DB1_USB_EXTD_OC_L0.480––
XDP_DB2_PCH_GPIO100.539––
XDP_DB3_SDCONN_STATE_CHANGE_L0.451––
XDP_DBRESET_L0.676––
XDP_DC0_DP_AUXCH_ISOL_L0.540––
XDP_DC1_SATARDRVR_EN0.598––
XDP_DC2_PCH_GPIO360.549––
XDP_DC3_JTAG_ISP_TCK0.525––
XDP_DD0_PCH_GPIO160.581––
XDP_DD1_PCH_GPIO490.594––
XDP_DD2_ENET_CLKREQ_L0.550––
XDP_DD3_AP_CLKREQ_L0.464––
XDP_FC0_HDD_PWR_EN0.535––
XDP_FC1_GPU_GOOD0.554––
XDP_PCH_PWRBTN_L0.432––
XDP_PCH_S5_PWRGD1.547––
XDP_PCH_TCK0.055––
XDP_PCH_TDI0.081––
XDP_PCH_TDO0.083––
XDP_PCH_TMS0.082––
XDP_VR_READY0.955––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP3V42_G3H read on the 820-3482?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3482: diode 0.329. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3482?

OpenBoardData's known-good values for PP5V_S5 on the 820-3482: diode 0.457. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-3482?

OpenBoardData's known-good values for PP3V3_S5 on the 820-3482: diode 0.145. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3482 board?

Open your own 820-3482 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License