Apple desktop board · OpenBoardData

820-3478 known-good readings

Known-good readings for the Apple desktop board 820-3478: 389 nets, including 54 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 52 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3478.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 54 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 5

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V2_G3H_SMC_VDDC0.514––
AI: what PP1V2_G3H_SMC_VDDC is and how to check it

PP1V2_G3H_SMC_VDDC is a 1.2 V rail feeding the SMC's VDDC supply; the G3H part of the name indicates it is always on (from the name). The only known-good reading in the archive is a diode value of 0.514 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied; no known-good voltage reading is available here. A diode reading far from 0.514 usually points to a short or a leaky part on the rail, but a single reading is only a guide, so confirm with a voltage check before replacing anything.

PP3V42_G3H0.316––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, per its name (G3H = always on); it should be present whenever the board has power. The archive lists one known-good reading: diode 0.316 to ground, board unpowered. Check it in diode mode with power off, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.316 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP12V_G3H0.557––
AI: what PP12V_G3H is and how to check it

PP12V_G3H is a 12 V rail that, judging by the "G3H" in its name, is an always-on rail present whenever the board has power. The only known-good reading here is a diode value of 0.557 to ground with the board unpowered; no known-good voltage reading is recorded. Check it by measuring diode mode from PP12V_G3H to ground with power off, then measure the voltage on the rail with power applied. A diode reading far below 0.557 suggests a short or a leaky load on the rail; a much higher reading can mean an open trace or missing connection. These are guides only, and a small difference can be normal.

PP12V_G3H_P3V420.557––
AI: what PP12V_G3H_P3V42 is and how to check it
  • What it is: From its name, PP12V_G3H_P3V42 is a 12 V rail in the G3H (always-on) startup group on the 820-3478. The P3V42 suffix suggests it's tied to the 3.42 V always-on rail, but that's general reading of the name, not from board data.
  • Known-good: The archive lists a diode reading of 0.557 to ground for this net. No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with 0.557. Then apply power and measure the voltage; no known-good voltage is available, so compare against the same rail on a known-good board.
  • If far off: A diode reading well below 0.557 suggests a short or leaky part on the rail; well above suggests an open. Confirm with a second measurement before replacing anything.
PPVBATT_G3_RTCOL––
AI: what PPVBATT_G3_RTC is and how to check it

PPVBATT_G3_RTC — the name suggests a battery-backed, always-on rail (G3H) feeding the RTC circuit. It is likely the small coin-cell or backup supply that keeps the real-time clock alive when the main battery is out.

  • Known-good readings: the archive lists diode mode to ground as OL (open). No known-good voltage is listed here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground; OL matches the archive. Then apply power and measure the voltage on the rail.
  • If it reads far from OL in diode mode (a low reading), that usually points to a short or a leaky part on the rail, not to the rail itself. A missing voltage with power applied points to the backup source or its path.

These are community readings and only a guide; the board's state affects them.

S5 and SUS: standby 3

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.146––
AI: what PP3V3_S5 is and how to check it
  • PP3V3_S5 is a 3.3 V standby rail; the "S5" in its name places it in the standby stage, so it should be present whenever the board has standby power.
  • Known-good reading here: diode mode to ground 0.146 (board unpowered). No known-good voltage reading is recorded for this rail.
  • To check it: with power off, measure diode mode from the rail to ground and compare with 0.146; then apply power and measure the DC voltage on the rail.
  • A diode reading far below 0.146 usually points to a short or a failing load on the rail; a reading far above can mean an open path. Confirm with a voltage measurement before replacing anything, since one reading alone isn't proof.
PP5V_S50.396––
AI: what PP5V_S5 is and how to check it
  • PP5V_S5 is a 5 V standby rail; the "S5" in its name marks it as a standby-stage supply (general naming convention, not from board data).
  • Known-good reading: diode 0.396 to ground, board unpowered. No known-good voltage reading here.
  • Check it with the board off in diode mode from PP5V_S5 to ground, then power up and measure the voltage on the rail.
  • A diode reading far from 0.396 usually points to a short or a leaky part on that rail; confirm with a voltage check before replacing anything.
PP12V_S50.524––
AI: what PP12V_S5 is and how to check it
  • What it is: PP12V_S5 is a 12 V rail in the S5 standby stage, from its name. It's present while the board is in standby, before full power-on.
  • Known-good reading: diode 0.524 to ground, from the readings archive. This is a community guide, not a factory spec, and no voltage reading is listed for this rail.
  • How to check: power off and unplug, then measure diode mode from PP12V_S5 to ground. Then apply power and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or a leaky part on the rail; an open or high reading suggests a broken trace or missing feed. A wrong voltage with a normal diode reading points more to the source or enable side.
  • Unsure: which parts sit on this net isn't known here, so trace the rail on the board before replacing anything.

S4 15

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V8_S4_CAMERA0.434––
AI: what PP1V8_S4_CAMERA is and how to check it

PP1V8_S4_CAMERA is a 1.8 V rail, judged from its name, and the S4 tag suggests it comes up in the S4 startup stage (general naming convention, not confirmed by board data). The only known-good reading here is a diode value of 0.434 to ground; no known-good voltage reading is listed. With the board unpowered, measure diode mode from the rail to ground and compare against 0.434. Then apply power and check the voltage, comparing to 1.8 V as the name implies. A diode reading far below 0.434 usually points to a short or a failing part on the rail; a far higher or open reading points to a broken connection.

PP1V8_S4_CAMERA_F0.435––
AI: what PP1V8_S4_CAMERA_F is and how to check it

PP1V8_S4_CAMERA_F — reference note

  • From its name, this is a 1.8 V rail (PP1V8) in the S4 power state, feeding the camera section (CAMERA_F). The S4 tag is from the name only; it doesn't confirm the exact power sequence.
  • Known-good reading: diode 0.435 in diode mode to ground, board unpowered. No known-good voltage reading here, so compare the powered voltage against the rail's nominal 1.8 V and a known-good board.
  • To check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • A diode reading far below 0.435 usually points to a short or leaky load on the rail; far above it can mean an open trace or missing connection. A voltage well off 1.8 V with a normal diode reading points more toward the supply side. These are general guides, not confirmed causes.
PP3V3_S40.338––
AI: what PP3V3_S4 is and how to check it
  • What it is: PP3V3_S4 is a 3.3 V rail in the S4 startup stage, from its name. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.338 to ground, from the readings archive. No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from PP3V3_S4 to ground. Then apply power and measure the voltage.
  • If it's far off: a much lower diode reading suggests a short or a failing part on the rail; a missing voltage points to the rail not being enabled or its source not switching. These are guides, not confirmed faults.
PP3V3_S4_ALS_F0.338––
AI: what PP3V3_S4_ALS_F is and how to check it

PP3V3_S4_ALS_F is a 3.3 V rail in the S4 power stage, from its name; the "ALS" suffix suggests it feeds an ambient light sensor, though that's general inference, not from board data. The only known-good reading here is a diode value of 0.338 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.338 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP3V3_S4_CAMFILT0.338––
AI: what PP3V3_S4_CAMFILT is and how to check it
  • What it is: A 3.3 V rail at the S4 startup stage, judging by the name (PP = power rail, 3V3 = 3.3 V, S4 = sleep-state 4 stage, CAMFILT = camera filter). The exact parts on it aren't documented here.
  • Known-good reading: diode 0.338 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.338. Then power on and measure the rail voltage; S4 rails normally come up in the later part of the power sequence, so check the earlier rails are present first (general guidance).
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing connection. A single reading isn't proof a part is bad, so compare against a matching net or a known-good board before replacing anything.
PP5V_S40.155––
AI: what PP5V_S4 is and how to check it
  • What it is: PP5V_S4 is a 5 V rail in the S4 startup stage, judged from its name; the board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.155 to ground (community archive, guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from PP5V_S4 to ground, then power on and measure the voltage.
  • If far off: a much lower diode reading suggests a short or leaky load on the rail; a much higher one suggests an open path. Confirm with voltage before replacing anything.
PP5V_S4_CAMERA_F0.154––
AI: what PP5V_S4_CAMERA_F is and how to check it
  • What it is: PP5V_S4_CAMERA_F is a 5 V rail for the camera circuit, enabled in the S4 power state — that reading is from the rail's name, not from board data.
  • Known-good reading: diode 0.154 in the readings archive. That's a community value and a guide only; there's no known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.154. Then apply power, bring the board into S4, and measure the voltage — it should sit near 5 V.
  • If it's far off: a much lower diode reading suggests a short or a leaky load on the rail; a correct diode reading with no voltage points upstream, at the rail's enable or supply. Which parts sit on this net isn't known here, so trace it on the board before replacing anything.
PP5V_S4_EXTA_F0.526––
AI: what PP5V_S4_EXTA_F is and how to check it

PP5V_S4_EXTA_F — a 5 V rail in the S4 startup stage, both from the name. The archive lists one known-good reading: diode mode to ground 0.526, with no condition noted.

  • Check it unpowered: diode mode, black probe on ground, red on the rail. Compare with 0.526.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed here.
  • A diode reading far below 0.526 suggests a short or a leaky part on the rail; far above can mean an open path. One reading alone doesn't condemn a part, so confirm with a second measurement before replacing anything.
PP5V_S4_EXTA_ILIM0.526––
AI: what PP5V_S4_EXTA_ILIM is and how to check it

PP5V_S4_EXTA_ILIM is a 5 V rail in the S4 startup stage, judging from its name; the "ILIM" suffix suggests it feeds a current-limit reference or sense point rather than a heavy load. The only known-good reading here is a diode value of 0.526 to ground, with no condition noted, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.526 usually points to a short or a leaky part on that net, while a much higher reading can mean an open trace or missing connection; treat the 0.526 as a guide only, since community readings vary with board state.

PP5V_S4_EXTB_F0.526––
AI: what PP5V_S4_EXTB_F is and how to check it

PP5V_S4_EXTB_F is a 5 V rail; the "S4" in its name marks it as a later startup stage, and "EXTB" suggests it feeds an external device or connector (that part is from the name, not confirmed here). The archived reading is diode 0.526 to ground, with no condition recorded, so treat it as a guide only. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and the rail enabled. No known-good voltage reading is recorded here, so compare against a matching rail on a known-good board. A diode reading far from 0.526 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S4_EXTB_ILIM0.526––
AI: what PP5V_S4_EXTB_ILIM is and how to check it

PP5V_S4_EXTB_ILIM is a 5 V rail in the S4 startup stage, judging from its name; the ILIM suffix suggests it feeds a current-limit reference or sense point rather than a heavy load. The only known-good reading in the archive is a diode value of 0.526 to ground, with no condition recorded, and there is no known-good voltage reading here. Check it unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with the board powered. A diode reading far below 0.526 usually points to a short or a leaky part on that net, while a much higher reading can mean an open trace or missing connection; confirm with the powered voltage before suspecting any part.

PP5V_S4_EXTC_F0.528––
PP5V_S4_EXTC_ILIM0.528––
AI: what PP5V_S4_EXTC_ILIM is and how to check it

PP5V_S4_EXTC_ILIM is a 5 V rail in the S4 startup stage, judging from its name; the "ILIM" part suggests it feeds a current-limit reference, though that's general interpretation, not from this board's data. The only known-good reading here is a diode value of 0.528 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered. No known-good voltage reading exists here, so compare against a matching rail on a known-good board. A diode reading far from 0.528 usually points to a short or leaky component on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S4_EXTD_F0.527––
AI: what PP5V_S4_EXTD_F is and how to check it

PP5V_S4_EXTD_F is a 5 V rail in the S4 startup stage, judging from its name; the "EXTD" part suggests it's an external or extended 5 V feed, but the exact circuit isn't documented here. The only known-good reading is a diode value of 0.527 to ground, with no condition listed and no voltage reading recorded. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied. A diode reading far from 0.527 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP5V_S4_EXTD_ILIM0.527––
AI: what PP5V_S4_EXTD_ILIM is and how to check it
  • What it is: From its name, PP5V_S4_EXTD_ILIM is a 5 V rail that comes up at the S4 startup stage, with "ILIM" suggesting a current-limit reference or sense point. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.527 to ground, from the community archive (no condition given). No known-good voltage reading here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.527. Then power up and measure the DC voltage at the rail.
  • If far off: A diode reading well below 0.527 usually points to a short or leaky part on the rail; well above it can mean an open path. Confirm with the voltage measurement before replacing anything.

S3: memory 2

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PPVDDQ_S30.327––
AI: what PPVDDQ_S3 is and how to check it
  • What it is: PPVDDQ_S3 is a memory-rail supply, judged from its name: "PP" is a power rail, "VDDQ" is the DDR I/O supply, and "S3" is the memory startup stage. The parts on this net aren't known.
  • Known-good reading: diode 0.327 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PPVDDQ_S3 to ground; then apply power and measure the rail voltage.
  • If far off: a much lower diode reading usually points to a short or a bad part on the rail; a much higher one to an open or missing connection. Confirm with a second measurement before replacing anything.
PPVDDQ_S3_DDR0.327––
AI: what PPVDDQ_S3_DDR is and how to check it

PPVDDQ_S3_DDR is a memory-stage (S3) DDR supply rail; that reading comes from the name, not from a board file. The only known-good figure here is a diode reading of 0.327 to ground, with no condition recorded; there is no known-good voltage or resistance reading for this rail. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered and compare against a known-good board. A diode reading far from 0.327 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

S0: running 29

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.037–36.400R
AI: what PP1V05_S0 is and how to check it

PP1V05_S0 is a 1.05 V rail that, from its name, belongs to the S0 (running) power state. Community readings for it are diode 0.037 and resistance 36.400R; treat these as a guide only, since they vary with board state.

  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered.
  • A reading far from known-good on the diode or resistance check usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.
  • No known-good voltage reading is recorded here, so compare against a known-good board or a matching rail.
PP1V5_S00.121––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the S0 suffix, from its name, marks it as a running-state supply rather than a standby rail. The only known-good figure here is a diode reading of 0.121 to ground, with no condition noted and no known-good voltage reading. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode value far from 0.121 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP1V5_S0_PCH0.121––
AI: what PP1V5_S0_PCH is and how to check it

PP1V5_S0_PCH is a 1.5 V rail; the "S0" in its name marks it as a running-state supply, and "PCH" points to the chipset. In the readings archive its only known-good figure is a diode reading of 0.121 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode value far below 0.121 usually suggests a short or a failing load on the rail; a small difference can be normal, so confirm with the voltage before replacing anything.

PP3V3_S00.290––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is a 3.3 V rail that, judging by its name, is up in the S0 (running) state. The archive lists one known-good diode reading of 0.290 to ground; no known-good voltage is listed here.

  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage.
  • A diode reading far below 0.290 suggests a short or a leaky load on the rail; a much higher one can mean an open path.
  • No known-good voltage is recorded, so compare the powered voltage against the rail's nominal 3.3 V and a known-good board.

These readings are community guides and vary with board state, so treat one reading as a hint, not proof a part is bad.

PP3V3_S0_SW_SD_PWR0.558––
AI: what PP3V3_S0_SW_SD_PWR is and how to check it

PP3V3_S0_SW_SD_PWR (820-3478) — reference note

  • From its name, this is a 3.3 V rail that is switched (SW) and feeds SD power; the S0 suffix places it in the running state, so it should come up once the board is fully on, not during early standby.
  • Known-good reading: diode 0.558 in diode mode to ground, board unpowered. This is a community value and a guide only; the archive has no known-good voltage for this rail.
  • To check it: power off, measure diode mode from the rail to ground and compare with 0.558, then power the board and measure the voltage at the rail.
  • A diode reading far below 0.558 suggests a short or a leaky load on the rail; far above it suggests an open path or a missing connection. Confirm with the powered voltage before suspecting any part, since one reading alone doesn't prove a fault.
PP5V_S00.353––
AI: what PP5V_S0 is and how to check it

PP5V_S0 is a 5 V rail that is present in the S0 (running) state, based on its name. The archive lists a known-good diode reading of 0.353 to ground for this net; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from PP5V_S0 to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.353 usually points to a short or a faulty component on the rail, but one reading alone doesn't confirm a bad part, so compare against a matching net or a known-good board before replacing anything.

PP5V_S0_BLC_R0.355––
AI: what PP5V_S0_BLC_R is and how to check it

PP5V_S0_BLC_R is a 5 V rail that, from its name, belongs to the backlight circuit and is active in the S0 (running) state. The only known-good figure here is a diode reading of 0.355 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.355.
  • Then power the board and measure the DC voltage on the rail; no known-good voltage is listed, so judge it against the 5 V in the name and a matching rail on a known-good board.
  • A diode reading far below 0.355 usually points to a short or a leaky part on the rail; far above it can mean an open path. These are guides only, not confirmed faults.
PP5V_S0_HDD0.597––
AI: what PP5V_S0_HDD is and how to check it

PP5V_S0_HDD is a 5 V rail that, from its name, is switched on in the S0 (running) state and feeds the hard drive circuit. The only known-good reading here is a diode value of 0.597 to ground; there is no known-good voltage reading for this rail in the data.

  • Check it unpowered: diode mode, black probe on ground, red on the rail, and compare with 0.597.
  • Then power the board and measure the DC voltage on the rail; it should be about 5 V, which is general expectation from the rail name, not a recorded value.
  • A diode reading far below 0.597 suggests a short or leaky part on the rail; far above it suggests an open path. Either way, confirm with a second measurement before replacing anything.
PP12V_S00.434––
AI: what PP12V_S0 is and how to check it
  • PP12V_S0 is a 12 V rail; the "S0" in the name indicates it belongs to the running (S0) state, so it should be present once the board is powered on.
  • Known-good reading from the archive: diode 0.434 to ground. No known-good voltage reading here.
  • Check it unpowered in diode mode from PP12V_S0 to ground, then power the board and measure the voltage.
  • A diode reading far from 0.434 usually points to a short or a leaky part on that rail; confirm with a resistance check before replacing anything.
PP12V_S0_BLC0.499––
AI: what PP12V_S0_BLC is and how to check it
  • What it is: From its name, PP12V_S0_BLC is a 12 V rail that is on in the S0 (running) state, and the BLC suffix usually points to backlight circuitry. That's general naming, not confirmed from board data.
  • Known-good reading: diode 0.499 to ground, with no condition listed. No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the DC voltage on the rail.
  • If it's far off: a diode reading well below known-good often suggests a shorted load on the rail; a much higher or open reading can mean a broken trace or missing connection. Confirm with the voltage reading before replacing anything.
PP12V_S0_BLC_F0.499––
AI: what PP12V_S0_BLC_F is and how to check it

PP12V_S0_BLC_F — the name suggests a 12 V rail for backlight (BLC) that is present in the S0 running state. That meaning is from the name only; the parts on the net aren't known here.

  • Known-good: diode 0.499 to ground, board unpowered. No known-good voltage reading is available here.
  • Check: power off, diode mode, red probe to ground and black to the rail (or the reverse, matching how the 0.499 was taken). Then power up and measure the DC voltage at the rail.
  • A diode reading far below 0.499 usually points to a short or a leaky load on the rail; a much higher one can mean an open path. Confirm with a second measurement before suspecting a part.
PP12V_S0_BLC_VIN20.497––
AI: what PP12V_S0_BLC_VIN2 is and how to check it

PP12V_S0_BLC_VIN2 is a backlight-related input rail; the "BLC" and "VIN" parts of the name suggest backlight converter input, and the S0 suffix means it's present in the running state (from the name, not from board data). The only known-good reading here is a diode value of 0.497 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied. A diode reading far below 0.497 usually points to a short or leaky component on that rail, while a much higher or open reading suggests a broken connection; a single off reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP12V_S0_BLC_VINP0.507––
AI: what PP12V_S0_BLC_VINP is and how to check it

PP12V_S0_BLC_VINP is a 12 V backlight-related rail; the S0 in its name indicates it belongs to the running state, and the BLC/VINP parts suggest it feeds the backlight boost input. The only known-good reading here is a diode value of 0.507 to ground, with no condition noted and no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.507 usually points to a short or a damaged component on that net, but one reading alone isn't proof, so compare against a matching net or a known-good board before replacing anything.

PP12V_S0_CPUVCC_FLT0.435––
AI: what PP12V_S0_CPUVCC_FLT is and how to check it
  • What it is: From its name, PP12V_S0_CPUVCC_FLT is a 12 V rail in the S0 (running) power state, tied to CPU VCC and flagged as a fault line. The archive doesn't list which parts sit on it.
  • Known-good reading: diode 0.435 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open feed or a missing part. Confirm with a voltage check before replacing anything.
PP12V_S0_FAN_0_FILT0.434––
AI: what PP12V_S0_FAN_0_FILT is and how to check it

PP12V_S0_FAN_0_FILT is a 12 V fan rail that is switched on in the S0 (running) state, judged from its name. The only known-good reading here is a diode value of 0.434 to ground, with no stated condition; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.434 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part.

PP12V_S0_FBVDDQ0.435––
AI: what PP12V_S0_FBVDDQ is and how to check it

PP12V_S0_FBVDDQ is a 12 V rail that, from its name, belongs to the S0 (running) power state and feeds FBVDDQ, a memory-related supply. The only known-good figure here is a diode reading of 0.435 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far below 0.435 usually points to a shorted load or capacitor on the rail, while a far higher or open reading suggests a broken trace or missing connection; confirm with a second measurement before replacing anything.

PP12V_S0_GPUCORE0.434––
AI: what PP12V_S0_GPUCORE is and how to check it

PP12V_S0_GPUCORE is a 12 V rail feeding the GPU core supply, and the S0 in its name indicates it belongs to the running (S0) state. The only known-good reading here is a diode value of 0.434 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.434 usually points to a short or a leaky component on the rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP12V_S0_GPUCORE_FLT0.434–0.000R
AI: what PP12V_S0_GPUCORE_FLT is and how to check it

PP12V_S0_GPUCORE_FLT is a 12 V rail for the GPU core supply, and the S0 in its name indicates it belongs to the running (S0) state. The archive lists a known-good diode reading of 0.434 to ground and a resistance of 0.000R; treat these as a guide, since community readings vary with board state. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.434, or a resistance that stays near 0.000R, usually points to a short or a failed component on that rail rather than the rail itself. No known-good voltage reading is available here, so compare against a matching rail or a known-good board.

PP12V_S0_HDD0.434––
AI: what PP12V_S0_HDD is and how to check it
  • What it is: PP12V_S0_HDD is a 12 V rail feeding the hard drive, from its name; the S0 suffix means it's up in the running state.
  • Known-good reading: diode 0.434 to ground, from the readings archive (a community guide, not a spec).
  • How to check: power off and unplug, then diode mode from PP12V_S0_HDD to ground; then power up and measure the voltage on the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail; no voltage at S0 points to the rail's supply or enable. No known-good voltage reading is listed here, so compare against a known-good board.
PPCPUVCC_S0_CPU0.001–1.100R
AI: what PPCPUVCC_S0_CPU is and how to check it

PPCPUVCC_S0_CPU is the CPU core supply rail that is active in the S0 (running) state, as the name suggests. The archive gives a known-good diode reading of 0.001 to ground and a resistance of 1.100R; both are very low, which is normal for a CPU core rail. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in S0. A reading far above these values usually points to an open or missing connection rather than a short; no known-good voltage reading is recorded here, so compare against a known-good board of the same model.

PPDDRVTT_S00.573––
AI: what PPDDRVTT_S0 is and how to check it

PPDDRVTT_S0 is a DDR termination rail; the "VTT" in the name (from the name) is the memory termination voltage, and the S0 suffix marks it as a running-state rail. The archive lists one known-good diode reading, 0.573, with no condition noted, and no known-good voltage here. Check it unpowered in diode mode from the net to ground, then measure the voltage with the board powered and running. A diode reading far from 0.573 usually points to a short or a damaged part on that net, but one reading isn't proof — confirm with the voltage and compare against a known-good board before replacing anything.

PPFBVDDQ_S0_GPU0.062–62.100R
AI: what PPFBVDDQ_S0_GPU is and how to check it

PPFBVDDQ_S0_GPU is a GPU-related power rail; the S0 in its name indicates it belongs to the running (S0) state, and the FBVDDQ part suggests a memory/IO supply for the GPU (that reading is from the name, not the data).

  • Known-good from the archive: diode 0.062 to ground, resistance 62.100R. No known-good voltage reading is recorded here.
  • Check it unpowered in diode mode to ground, then measure the voltage with the board powered and in S0.
  • A diode or resistance far below 62.100R/0.062 usually points to a short or a failing load on the rail; confirm with a second reading before replacing anything.
PPGPUCORE_S0_SENSE_10.012––
AI: what PPGPUCORE_S0_SENSE_1 is and how to check it

PPGPUCORE_S0_SENSE_1 is a sense line for the GPU core supply in the running (S0) state, judging by its name. The only known-good reading here is diode 0.012 to ground, with no stated condition. Check it unpowered in diode mode to ground, then confirm the voltage with the board powered. A reading far from 0.012 usually points to a short or open on that sense net rather than the rail itself; no known-good voltage reading exists here, so compare against a matching sense net or a known-good board.

PPGPUCORE_S0_SENSE_20.012––
AI: what PPGPUCORE_S0_SENSE_2 is and how to check it
  • What it is: From its name, PPGPUCORE_S0_SENSE_2 is a sense line tied to the GPU core supply, active in the S0 (running) state. The board data doesn't say which parts sit on it.
  • Known-good reading: diode 0.012, with no condition recorded. That is a very low diode reading, so treat it as a low-resistance sense node rather than a normal power rail. No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, measure diode mode from the net to ground and compare with 0.012. Then apply power and measure the voltage on the net.
  • If it's far off: a much higher diode reading usually points to an open trace or a missing connection on the sense line, not necessarily a bad supply. Confirm with a second measurement before replacing anything.
PPGPUCORE_S0_SENSE_30.012–11.600R
AI: what PPGPUCORE_S0_SENSE_3 is and how to check it
  • What it is: From the name, PPGPUCORE_S0_SENSE_3 is a sense line tied to the GPU core supply, active in S0 (running) state. Which parts sit on it isn't known here.
  • Known-good readings: diode 0.012 and resistance 11.600R, from the community archive — treat as a guide, and note both are very low.
  • How to check: Power off, measure diode mode to ground on the net, then resistance; with power applied, measure the voltage on it.
  • If far from known-good: a much higher diode or resistance reading usually points to an open trace or missing connection rather than a shorted part; no known-good voltage reading is available here, so compare against a matching sense net or a known-good board.
PPGPUCORE_S0_SENSE_40.012–11.600R
AI: what PPGPUCORE_S0_SENSE_4 is and how to check it

PPGPUCORE_S0_SENSE_4 is a GPU core sense line on the 820-3478; the S0 in its name indicates the running state, and "SENSE" suggests it carries a feedback or monitoring signal rather than a power rail. Known-good readings from the archive are diode 0.012 and resistance 11.600R, both taken with the board unpowered. Check it by measuring diode mode to ground with power off, then confirm the voltage with the board powered. A reading far from these low values usually points to a short or a damaged component on that net, but no known-good powered voltage is recorded here, so compare against a matching sense net or a known-good board.

PPHDD12_S00.434––
PPSSD_S00.290––
AI: what PPSSD_S0 is and how to check it

PPSSD_S0 is the SSD power rail, and the S0 in its name indicates it is active in the running state. The only known-good reading recorded here is a diode value of 0.290; no known-good voltage reading is available.

  • Check it unpowered: diode mode, black probe to ground, red probe on PPSSD_S0, and compare with 0.290.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed, so compare against a known-good board or the rail's expected level.
  • A diode reading far from 0.290 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a bad part.
PPVCORE_S0_GPU0.012––
AI: what PPVCORE_S0_GPU is and how to check it
  • What it is: PPVCORE_S0_GPU is the GPU core power rail. The "S0" in the name means it's present in the running state, and "VCORE" points to a processor core supply. That reading is from the name, not from a schematic.
  • Known-good reading: diode 0.012 to ground, from the community archive. Treat it as a guide only, since readings vary with board state.
  • How to check: power off and measure diode mode from the rail to ground, then power up and measure the voltage. No known-good voltage is recorded for this rail.
  • If it's far off: a much higher diode reading often means an open trace or missing feed; near zero suggests a short. Confirm with a second measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
9V_COMP_REF0.677––
12V_COMP_REF0.667––
AGND_BLC0.000––
AUD_GPIO_30.555––
AUD_HP_PORT_REFOL––
AUD_I2C_INT_L0.524––
AUD_IPHS_SWITCH_EN0.540––
AUD_IPHS_SWITCH_EN_PCH0.640––
AUD_LAMP_BOOTLN0.584––
AUD_LAMP_BOOTLP0.587––
AUD_LAMP_BOOTRN0.584––
AUD_LAMP_BOOTRP0.587––
AUD_LAMP_LINC_N0.712––
AUD_LAMP_LINC_P0.717––
AUD_LAMP_OUTNL0.546––
AUD_LAMP_OUTNR0.545––
AUD_LAMP_OUTPL0.546––
AUD_LAMP_OUTPR0.545––
AUD_LAMP_RINC_N0.656––
AUD_LAMP_RINC_P0.714––
AUD_LO1_L_C_NOL––
AUD_LO1_L_C_POL––
AUD_LO1_L_N0.712––
AUD_LO1_L_P0.717––
AUD_LO1_R_C_NOL––
AUD_LO1_R_C_POL––
AUD_LO1_R_N0.715––
AUD_LO1_R_P0.713––
AUD_LO2_L_N0.714––
AUD_LO2_L_P0.656––
AUD_LO2_R_N0.714––
AUD_LO2_R_P0.715––
AUD_PORTD_DET_L1.109––
AUD_RAMP_LINC_N0.715––
AUD_RAMP_LINC_P0.713––
AUD_RAMP_OUTNL0.560––
AUD_RAMP_OUTNR0.559––
AUD_RAMP_OUTPL0.562––
AUD_RAMP_OUTPR0.562––
AUD_RAMP_RINC_N0.715––
AUD_RAMP_RINC_P0.714––
AUD_SPKR_LTWT_OUT_N0.546––
AUD_SPKR_LTWT_OUT_P0.545––
AUD_SPKR_LWFR_OUT_N0.546––
AUD_SPKR_LWFR_OUT_P0.545––
AUD_SPKR_RTWT_OUT_N0.560––
AUD_SPKR_RTWT_OUT_P0.562––
AUD_SPKR_RWFR_OUT_N0.562––
AUD_SPKR_RWFR_OUT_P0.559––
AUD_SPKR_VENDOR_ID_ROL––
AUD_SPKRAMP_WIN_SHDN_L0.555––
BLC_BL_GATE0.741––
BLC_BST0.739––
BLC_BYPASS_GATE0.746––
BLC_EN0.779––
BLC_ENA10.694––
BLC_GND_10.000––
BLC_GND_20.000––
BLC_GND_30.000––
BLC_LED_N_10.542––
BLC_LED_N_20.544––
BLC_LED_N_30.544––
BLC_LED_P_10.759––
BLC_LED_P_20.759––
BLC_LED_P_30.761––
BLC_MCU_BV0.532––
BLC_MCU_BV_D0.734––
BLC_MCU_BV_R0.739––
BLC_MCU_RXD00.667––
BLC_MCU_TXD00.672––
BLC_ON1.680––
BLC_ON_DRAIN0.551––
BLC_ON_R0.697––
BLC_P_ON0.600––
BLC_P_ON_BYPASS0.697––
BLC_P_ON_D1.308––
BLC_P_ON_D_R2.106––
BLC_P_ON_DRAIN0.556––
BLC_P_ON_GATE0.746––
BLC_P_ON_R0.698––
BLC_P3V3_REF0.605––
BLC_P3V3S0.287––
BLC_PWM_10.540––
BLC_PWM_20.561––
BLC_PWM_30.580––
BLC_SNUB_1OL––
BLC_SNUB_2OL––
BLC_SNUB_3OL––
BLC_UVLO0.734––
BLC_VIN2_GATEOL––
BLC_VIN2_SRC0.614––
BLC_VINP_GATEOL––
BLC_VOUT10.759––
BLC_VOUT20.759––
BLC_VOUT30.760––
BOOST_BYPASS0.606––
BOOST_FET_DRAINOL––
BOOST_GDRV_ROL––
BOOST_ISNS_ROL––
BURSTMODE_EN_R_L1.964––
CAM_P1V2_RST_HOLDOFF1.376––
CAM_P1V2_RST_HOLDOFF_L1.356––
CAM_PROC_RESET_L0.530––
CORE_VOLTAGES_ON0.591––
CORE_VOLTAGES_ON_R1.341––
CPU_PROCHOT_L0.065–63.900R
CS4206_FN1.934––
CS4206_FP0.449––
CS4206_VCOM0.606––
DP_TBTSNK0_HPD0.513––
DP_TBTSNK1_ML_C_N<3>0.388––
ENET_ACTOL––
ENET_CS_L0.708––
ENET_MISO0.620––
ENET_MOSI0.733––
ENET_SCLK0.731––
ENET_SR_LX0.290––
ENET_TRAFFICLED_L0.753––
ENET_VMAIN_PRSNT0.596––
ENETCONN_MCT_BSOL––
ENETCONN_MCT0OL––
ENETCONN_MCT1OL––
ENETCONN_MCT2OL––
ENETCONN_MCT3OL––
ENETCONN_MDI_N<0>0.375––
ENETCONN_MDI_N<1>0.375––
ENETCONN_MDI_N<2>0.374––
ENETCONN_MDI_N<3>0.374––
ENETCONN_MDI_P<0>0.374––
ENETCONN_MDI_P<1>0.374––
ENETCONN_MDI_P<2>0.374––
ENETCONN_MDI_P<3>0.374––
ENETCONN_MDI_T_N<0>OL––
ENETCONN_MDI_T_N<1>OL––
ENETCONN_MDI_T_N<2>OL––
ENETCONN_MDI_T_N<3>OL––
ENETCONN_MDI_T_P<0>OL––
ENETCONN_MDI_T_P<1>OL––
ENETCONN_MDI_T_P<2>OL––
ENETCONN_MDI_T_P<3>OL––
ENETCONN_TCT0.374––
FAN_0_PWM_FET1.102––
FAN_0_PWM_FILT1.102––
FAN_0_TACH_FETOL––
FAN_0_TACH_FILTOL––
FET_EN_P12V_S0_R0.676––
FET_EN_P12V_S5_R0.678––
FET_HDD_SLGSW0.529––
FET_VCC_U84800.600––
FLAG_V_L0.553––
GND0.000––
GPU_PRESENT_DRAIN0.589––
GPU_PRESENT_R1.289––
HDD_12V_S0_GATE0.676––
HDD_OOB_1V00_REF0.704––
HDD_PWR_EN0.288––
HDD_PWR_EN_L0.603––
HDD_PWR_EN_R0.507––
HDD5V_RAMP_CAP0.646––
HS_HDET1.995––
HS_RX_BP0.594––
I2C_TBTRTR_SDA0.416––
IS1_BLC0.544––
IS1_BLC_F0.546––
IS2_BLC0.544––
IS2_BLC_F0.544––
IS3_BLC0.543––
IS3_BLC_F0.544––
ISNS_P12VS0_HDD_R0.710––
ITS_PLUGGED_IN1.146––
LCD_BKL_ON_DLY0.747––
LCD_SHOULD_ON_R1.297––
LED_DRIVER_FDBK_R_10.003––
LED_DRIVER_FDBK_R_20.002––
LED_DRIVER_FDBK_R_30.002––
LED_DRIVER_FDBK10.682––
LED_DRIVER_FLT10.689––
LED_DRIVER_FLT20.690––
LED_DRIVER_FLT30.692––
LED_DRIVER_GATE10.638––
LED_DRIVER_GATE1_R0.638––
LED_DRIVER_GATE20.637––
LED_DRIVER_GATE2_R0.637––
LED_DRIVER_GATE30.639––
LED_DRIVER_GATE3_R0.639––
LED_DRIVER_OVP10.687––
LED_DRIVER_OVP20.688––
LED_DRIVER_OVP30.688––
LED_DRVR_CS_RC_10.000––
LED_DRVR_CS_RC_20.000––
LED_DRVR_CS_RC_30.000––
LED_DRVR_DRAIN_10.508––
LED_DRVR_DRAIN_20.508––
LED_DRVR_DRAIN_30.508––
LED_FLT_R_10.689––
LED_FLT_R_20.712––
LED_FLT_R_30.712––
MAX97220_BIAS2.070––
MAX97220_C1N0.870––
MAX97220_C1P0.538––
MAX97220_INL_NOL––
MAX97220_INL_POL––
MAX97220_INR_NOL––
MAX97220_INR_POL––
MAX97220_OUTL1.350––
MAX97220_OUTR1.362––
MAX97220_PVSS1.465––
OVP_OREF0.675––
OVP_OUT10.742––
OVP_OUT1_R0.742––
OVP_OUT20.739––
OVP_OUT2_R0.739––
OVP_OUT30.740––
OVP_OUT3_R0.741––
P3V3ENET_SSOL––
P3V42G3H_SW0.316––
PCH_CLK32K_RTCX10.762––
PCH_CLK32K_RTCX2_R0.755––
PCIE_WAKE_L0.514––
PGOOD_12V_S0_G10.668––
PGOOD_12V_S0_G20.611––
PGOOD_P12V_S0_R0.605––
PLT_RST_BUF_L0.699––
PM_EN_ENET_L0.578––
PM_EN_FET_P12V_S00.591––
PM_EN_FET_P12V_S0_R0.558––
PM_EN_REG_P3V3_S50.527––
PM_PCH_PWROK0.546––
PM_PGOOD_FET_P12V_S00.608––
PP1V2_ENET_INTREG0.290––
PP1V2_ENET_PHY_PCIEPLL0.290––
PP1V2_G3H_SMC_VDDC0.514––
PP1V05_S00.037–36.400R
PP1V5_S00.121––
PP1V5_S0_PCH0.121––
PP1V05_TBTCIO0.157––
PP1V05_TBTLC0.132––
PP1V8_S4_CAMERA0.434––
PP1V8_S4_CAMERA_F0.435––
PP3V3_DMIC_CONN0.287––
PP3V3_ENET0.359––
PP3V3_ENET_PHY_AVDDH0.359––
PP3V3_S00.290––
PP3V3_S0_SW_SD_PWR0.558––
PP3V3_S40.338––
PP3V3_S4_ALS_F0.338––
PP3V3_S4_CAMFILT0.338––
PP3V3_S50.146––
PP3V3_TBTLC0.418––
PP3V3RHV_SW_TBTAPWR0.565––
PP3V3RHV_SW_TBTBPWR0.565––
PP3V42_G3H0.316––
PP4V5_AUDIO_ANALOG0.498––
PP5V_AUDIO_HPAMP0.359––
PP5V_S00.353––
PP5V_S0_BLC_R0.355––
PP5V_S0_HDD0.597––
PP5V_S40.155––
PP5V_S4_CAMERA_F0.154––
PP5V_S4_EXTA_F0.526––
PP5V_S4_EXTA_ILIM0.526––
PP5V_S4_EXTB_F0.526––
PP5V_S4_EXTB_ILIM0.526––
PP5V_S4_EXTC_F0.528––
PP5V_S4_EXTC_ILIM0.528––
PP5V_S4_EXTD_F0.527––
PP5V_S4_EXTD_ILIM0.527––
PP5V_S50.396––
PP8V_BLC0.666––
PP12V_ACDC0.557––
PP12V_G3H0.557––
PP12V_G3H_P3V420.557––
PP12V_LCD0.434––
PP12V_S00.434––
PP12V_S0_BLC0.499––
PP12V_S0_BLC_F0.499––
PP12V_S0_BLC_VIN20.497––
PP12V_S0_BLC_VINP0.507––
PP12V_S0_CPUVCC_FLT0.435––
PP12V_S0_FAN_0_FILT0.434––
PP12V_S0_FBVDDQ0.435––
PP12V_S0_GPUCORE0.434––
PP12V_S0_GPUCORE_FLT0.434–0.000R
PP12V_S0_HDD0.434––
PP12V_S50.524––
PPCPUVCC_S0_CPU0.001–1.100R
PPDDRVTT_S00.573––
PPFBVDDQ_S0_GPU0.062–62.100R
PPGPUCORE_S0_SENSE_10.012––
PPGPUCORE_S0_SENSE_20.012––
PPGPUCORE_S0_SENSE_30.012–11.600R
PPGPUCORE_S0_SENSE_40.012–11.600R
PPHDD12_S00.434––
PPHV_SW_TBTAPWR0.565––
PPHV_SW_TBTBPWR0.565––
PPSSD_S00.290––
PPVBATT_G3_RTCOL––
PPVCORE_S0_GPU0.012––
PPVDDQ_S30.327––
PPVDDQ_S3_DDR0.327––
PRE_REG_OUT0.508––
PWR_BTN_R1.738––
REG_BOOT_FBVDDQ0.565––
REG_BOOT_FBVDDQ_RC0.565––
REG_LGATE_P5VS40.457––
REG_PHASE_FBVDDQ0.062––
REG_PHASE_GPUCORE_10.012–11.600R
REG_PHASE_GPUCORE_20.012–11.600R
REG_PHASE_GPUCORE_30.012––
REG_PHASE_GPUCORE_40.012––
REG_PHASE_P1V05S0_L0.037––
REG_PHASE_P3V3S50.146––
REG_PHASE_P5VS40.155––
REG_PHASE_VDDQS3_L0.327––
REG_PVCC_U77500.355––
REG_UGATE_P5VS40.595––
REG_VCC_U70000.560––
REG_VCC_U77500.363––
REG_VIN_U76000.254––
SATA_HDD_D2R_C_NOL––
SATA_HDD_D2R_C_POL––
SATA_HDD_R2D_C_N0.345––
SATA_HDD_R2D_C_P0.347––
SATA_HDD_R2D_NOL––
SATA_HDD_R2D_POL––
SMC_ACDC_ID_R1.600––
SMC_EXTAL0.777––
SMC_FAN_0_CTL0.752––
SMC_ONOFF_L0.755––
SMC_OOB1_D2R_L0.657––
SMC_OOB1_D2R_R0.704––
SMC_OOB1_RX_CN0.604––
SMC_OOB1_RX_FILT0.602––
SMC_XTAL_R0.766––
SNS_ACDC_N0.757––
SNS_ACDC_P0.757––
SNS_P1V5S0_N0.121––
SNS_P1V5S0_P0.121––
SNS_P12VG3H_N0.557––
SNS_P12VG3H_P0.557––
SNS_P12VS0_GPUCORE_N0.434––
SNS_P12VS0_GPUCORE_P0.434––
SNS_P12VS0_HDD_N0.434––
SNS_P12VS0_HDD_P0.434––
SNS_SSD_N0.290––
SNS_SSD_P0.290––
SPI_MLB_CLK0.612––
SPI_MLB_CS_L0.599––
SPI_MLB_MISO0.516––
SPI_MLB_MOSI0.527––
SPI_WP_L0.640––
SPIROM_USE_MLB0.527––
TBT_CLKREQ_ISOL_L0.468––
TBT_DDC_XBAR_EN_L0.524––
TBT_EN_LC_ISOL0.466––
TBT_EN_LC_PWR0.558––
TBT_EN_LC_RC1V050.466––
TBT_MONOBSN0.185––
TBT_MONOBSP0.184––
TBT_SPI_CS_L0.670––
TBT_SPI_MISO0.617––
TBT_TEST_EN0.000––
TBT_TEST_PWR_GOOD0.001––
TBT_TMU_CLK_OUT0.559––
TBTPOCRST_CT0.639––
TBTPOCRST_MR_L0.612––
TBTROM_HOLD_L0.738––
TBTROM_WP_L0.738––
TSNS_2_1_N0.771––
TSNS_2_1_P0.777––
TSNS_2_2_N0.773––
TSNS_2_2_P0.763––
TSNS_2_3_N0.762––
TSNS_2_3_P0.772––
UNCONNECTED_1OL––
UNCONNECTED_2OL––
UNCONNECTED_4130.744––
USB_ILIM1_ROL––
USB_ILIM2_ROL––
UVP_IN_10.736––
UVP_IN_1_REF0.739––
UVP_IN_20.738––
UVP_IN_30.734––
UVP_IN_40.739––
UVP_REF0.696––
VIDEO_ON0.810––
VIDEO_ON_J17_L0.751––
VIDEO_ON_L0.757––
VIDEO_ON_L_DLY0.794––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP3V42_G3H read on the 820-3478?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3478: diode 0.316. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3478?

OpenBoardData's known-good values for PP5V_S5 on the 820-3478: diode 0.396. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-3478?

OpenBoardData's known-good values for PP3V3_S5 on the 820-3478: diode 0.146. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3478 board?

Open your own 820-3478 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License