Apple laptop board · OpenBoardData
820-3330 known-good readings
Known-good readings for the Apple laptop board 820-3330: 197 nets, including 10 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 10 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-3330.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 10 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 1
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V42_G3H | 0.35 | – | – |
AI: what PP3V42_G3H is and how to check itPP3V42_G3H is the always-on 3.42 V rail, indicated by the G3H suffix in its name. The readings archive lists a known-good diode reading of 0.35 to ground for this net; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V42_G3H to ground and compare against 0.35. Then apply power and check the rail voltage. A diode reading far from 0.35 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. | |||
S5 and SUS: standby 3
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP5V_S5 | 0.45 | – | – |
AI: what PP5V_S5 is and how to check itPP5V_S5 is the 5 V standby rail; the S5/SUS part of the name says it belongs to the standby stage, before the board fully powers up. The only known-good reading here is a diode value of 0.45 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it unpowered in diode mode from PP5V_S5 to ground, then power the board and measure the voltage at the same point. A diode reading far below 0.45 suggests a short or a leaky load on the rail; a much higher one can mean an open path, though a single reading doesn't prove a part bad. No known-good voltage is listed, so compare against a matching rail on a known-good board rather than guessing a number. | |||
PP5V_S5_CUMULUS | OL | – | – |
AI: what PP5V_S5_CUMULUS is and how to check it
| |||
PPVIN_S5_HS_OTHER_ISNS | 0.44 | – | – |
AI: what PPVIN_S5_HS_OTHER_ISNS is and how to check it
| |||
S4 1
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S4 | 0.38 | – | – |
AI: what PP3V3_S4 is and how to check itPP3V3_S4 is a 3.3 V rail; the S4 suffix comes from its name and marks it as a startup-stage rail (S4) in the power sequence. The only archived reading is a diode value of 0.38 to ground; there is no known-good voltage or resistance reading here.
A diode reading far below 0.38 usually suggests a short or a leaky load on the rail; a much higher or open reading can mean a broken trace or missing feed. Treat 0.38 as a community guide only, since readings vary with board state. | |||
S3: memory 1
Stay on in sleep, keeping the memory alive.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP5V_S3 | 0.40 | – | – |
AI: what PP5V_S3 is and how to check itPP5V_S3 is the 5 V rail that comes up at the S3 (memory) stage of the power sequence, judged from its name. The only known-good figure here is a diode reading of 0.40 to ground; there is no known-good voltage reading for this rail.
A diode reading far below 0.40 suggests a short or a leaky load pulling the rail down; a much higher reading can mean an open trace or missing connection. A missing or low voltage with a normal diode reading points more to the rail not being enabled or its source not switching on. These are likely causes, not confirmed ones, so trace the enable and source before replacing anything. | |||
S0: running 4
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S0 | 0.29 | – | – |
AI: what PP3V3_S0 is and how to check itPP3V3_S0 is the 3.3 V rail that is up in the S0 (running) state, judging by its name. The archive lists one known-good diode reading for it: 0.29 to ground, board unpowered. Check it in diode mode with power off, then measure the voltage with the board powered and running; no known-good voltage reading here, so compare against a known-good board. A diode reading far from 0.29 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part. | |||
PP5V_S0 | 0.39 | – | – |
AI: what PP5V_S0 is and how to check itPP5V_S0 is the 5 V rail that is up in the S0 (running) state, judged from its name. The only known-good reading here is diode mode to ground: 0.39, with no condition recorded. Check it with the board unpowered in diode mode from PP5V_S0 to ground, then power up and measure the voltage in S0. No known-good voltage reading is available here. A diode reading far from 0.39 usually points to a short or a faulty part on the rail, but one reading alone doesn't confirm a fault. | |||
PP5V_S0_CPUIMVP_VCC | 0.40 | – | – |
AI: what PP5V_S0_CPUIMVP_VCC is and how to check itPP5V_S0_CPUIMVP_VCC is a 5 V rail that, from its name, runs in the S0 (fully on) state and feeds the CPU IMVP VCC supply. The archive lists one known-good reading: diode mode to ground 0.40, with no condition noted. Check it unpowered in diode mode from the rail to ground, then measure the voltage with the board powered in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.40 usually points to a short or a leaky part on the rail, but confirm with more than one reading before replacing anything. | |||
PPVOUT_S0_LCDBKLT | 0.59 | – | – |
AI: what PPVOUT_S0_LCDBKLT is and how to check itPPVOUT_S0_LCDBKLT is the LCD backlight output rail; the S0 in the name indicates it belongs to the running state. The only known-good reading here is a diode value of 0.59, with no condition recorded; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on it. A diode reading far from 0.59 usually points to a short or a leaky component on the rail, but one reading alone doesn't confirm a fault, so compare against a matching net or a known-good board before replacing anything. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
CHGR_ACIN | 0.53 | – | – |
CHGR_AGATE | 0.65 | – | – |
CHGR_AMON | 0.72 | – | – |
CHGR_BGATE | 0.66 | – | – |
CHGR_BMON | 0.72 | – | – |
CHGR_BOOT | 0.59 | – | – |
CHGR_CELL | 0.71 | – | – |
CHGR_CSI_N | 0.58 | – | – |
CHGR_CSI_P | 0.57 | – | – |
CHGR_CSO_N | 0.43 | – | – |
CHGR_CSO_P | 0.44 | – | – |
CHGR_ICOMP | 0.73 | – | – |
CHGR_LGATE | 0.46 | – | – |
CHGR_PHASE | 0.44 | – | – |
CHGR_RST_L | 0.49 | – | – |
CHGR_SGATE | 0.64 | – | – |
CHGR_UGATE | 0.90 | – | – |
CHGR_VCOMP | 0.72 | – | – |
CHGR_VFRQ | 0.53 | – | – |
CHGR_VNEG | 0.53 | – | – |
CPU_AXG_SENSE_R | 0.01 | – | – |
CPU_PROCHOT_L | 0.06 | – | – |
CPU_VCCSENSE_R | 0.01 | – | – |
CPU_VIDALERT_L | 0.07 | – | – |
CPU_VIDSCLK | 0.05 | – | – |
CPU_VIDSOUT | 0.06 | – | – |
CPUIMVP_AXG_PGOOD | 0.59 | – | – |
CPUIMVP_AXG_PWM2 | 0.56 | – | – |
CPUIMVP_BOOT1 | 0.60 | – | – |
CPUIMVP_BOOT1G | 0.60 | – | – |
CPUIMVP_BOOT2 | 0.60 | – | – |
CPUIMVP_FBA | 0.67 | – | – |
CPUIMVP_FBB | 0.67 | – | – |
CPUIMVP_IMAXA | 0.61 | – | – |
CPUIMVP_IMAXB | 0.58 | – | – |
CPUIMVP_ISUM | 0.09 | – | – |
CPUIMVP_ISUM_N | 0.00 | – | – |
CPUIMVP_ISUM1_P | 0.04 | – | – |
CPUIMVP_ISUM2_P | 0.04 | – | – |
CPUIMVP_ISUM3_P | 0.04 | – | – |
CPUIMVP_ISUMG_AVE_P | 0.09 | – | – |
CPUIMVP_ISUMG_N | 0.01 | – | – |
CPUIMVP_ISUMG1_P | 0.04 | – | – |
CPUIMVP_ISUMG2_P | 0.04 | – | – |
CPUIMVP_LGATE1 | 0.50 | – | – |
CPUIMVP_LGATE1G | 0.49 | – | – |
CPUIMVP_LGATE2 | 0.48 | – | – |
CPUIMVP_NTC | 0.59 | – | – |
CPUIMVP_NTCG | 0.68 | – | – |
CPUIMVP_PGOOD | 0.57 | – | – |
CPUIMVP_PHASE1 | 0.00 | – | – |
CPUIMVP_PHASE1G | 0.00 | – | – |
CPUIMVP_PHASE2 | 0.00 | – | – |
CPUIMVP_PWM3 | 0.56 | – | – |
CPUIMVP_SLEW | 0.68 | – | – |
CPUIMVP_TONA | 0.67 | – | – |
CPUIMVP_TONB | 0.67 | – | – |
CPUIMVP_UGATE1 | 0.68 | – | – |
CPUIMVP_UGATE1G | 0.68 | – | – |
CPUIMVP_UGATE2 | 0.68 | – | – |
CPUIMVP_VR_ON | 0.46 | – | – |
DP_EG_AUXCH_N | 0.63 | – | – |
DP_EG_AUXCH_P | 0.67 | – | – |
DP_EG_DDC_CLK | 0.67 | – | – |
DP_EG_DDC_DATA | 0.53 | – | – |
DP_EG_HPD | 0.52 | – | – |
DP_EXTA_AUXCH_C_N | 0.69 | – | – |
DP_EXTA_AUXCH_C_P | 0.69 | – | – |
DP_EXTA_DDC_CLK | 0.65 | – | – |
DP_EXTA_DDC_DATA | 0.65 | – | – |
DP_EXTA_HPD | 0.67 | – | – |
DP_IG_AUX_CH_N | 0.37 | – | – |
DP_IG_AUX_CH_P | 0.37 | – | – |
DP_IG_DDC_CLK | 0.55 | – | – |
DP_IG_DDC_DATA | 0.55 | – | – |
DP_IG_HPD | 0.70 | – | – |
DP_MUX_EN | 0.48 | – | – |
DP_MUX_SEL_EG | 0.43 | – | – |
GND_5V3V3_AGND | 0.00 | – | – |
GND_CHGR_AGND | 0.00 | – | – |
GND_CPUIMVP_SGND | 0.00 | – | – |
LED_RETURN_1 | 0.63 | – | – |
LED_RETURN_2 | 0.63 | – | – |
LED_RETURN_3 | 0.63 | – | – |
LED_RETURN_4 | 0.63 | – | – |
LED_RETURN_5 | 0.63 | – | – |
LED_RETURN_6 | 0.63 | – | – |
LVDS_CONN_A_CLK_F_N | 0.74 | – | – |
LVDS_CONN_A_CLK_F_P | 0.74 | – | – |
LVDS_CONN_A_DATA_N<0> | 0.74 | – | – |
LVDS_CONN_A_DATA_N<1> | 0.74 | – | – |
LVDS_CONN_A_DATA_N<2> | 0.74 | – | – |
LVDS_CONN_A_DATA_P<0> | 0.74 | – | – |
LVDS_CONN_A_DATA_P<1> | 0.74 | – | – |
LVDS_CONN_A_DATA_P<2> | 0.74 | – | – |
LVDS_CONN_B_CLK_F_N | 0.74 | – | – |
LVDS_CONN_B_CLK_F_P | 0.74 | – | – |
LVDS_CONN_B_DATA_N<0> | 0.74 | – | – |
LVDS_CONN_B_DATA_N<1> | 0.74 | – | – |
LVDS_CONN_B_DATA_N<2> | 0.74 | – | – |
LVDS_CONN_B_DATA_P<0> | 0.74 | – | – |
LVDS_CONN_B_DATA_P<1> | 0.74 | – | – |
LVDS_CONN_B_DATA_P<2> | 0.74 | – | – |
LVDS_DDC_CLK | 0.52 | – | – |
LVDS_DDC_DATA | 0.52 | – | – |
P3V3S5_COMP2 | 0.72 | – | – |
P3V3S5_CSN2 | 0.13 | – | – |
P3V3S5_CSP2 | 0.93 | – | – |
P3V3S5_DRVH | 0.67 | – | – |
P3V3S5_DRVL | 0.52 | – | – |
P3V3S5_EN | 0.52 | – | – |
P3V3S5_LL | 0.13 | – | – |
P3V3S5_RF | 0.57 | – | – |
P3V3S5_VBST | 0.56 | – | – |
P3V3S5_VFB2 | 0.56 | – | – |
P5VP3V3_SKIPSEL | 0.47 | – | – |
P5VP3V3_VREF2 | 0.47 | – | – |
P5VP3V3_VREG3 | 0.55 | – | – |
P5VS3_COMP1 | 0.72 | – | – |
P5VS3_CSN1 | 0.40 | – | – |
P5VS3_CSP1 | 1.40 | – | – |
P5VS3_DRVH | 0.93 | – | – |
P5VS3_DRVL | 0.53 | – | – |
P5VS3_LL | 0.40 | – | – |
P5VS3_PGOOD | 0.49 | – | – |
P5VS3_VBST | 0.62 | – | – |
P5VS3_VFB1 | 0.56 | – | – |
PICKB_L | 0.67 | – | – |
PM_SLP_S4_L | 0.48 | – | – |
PP3V3_S0 | 0.29 | – | – |
PP3V3_S4 | 0.38 | – | – |
PP3V3_SW_LCD | 0.59 | – | – |
PP3V42_G3H | 0.35 | – | – |
PP5V_S0 | 0.39 | – | – |
PP5V_S0_CPUIMVP_VCC | 0.40 | – | – |
PP5V_S3 | 0.40 | – | – |
PP5V_S5 | 0.45 | – | – |
PP5V_S5_CUMULUS | OL | – | – |
PP5V1_CHGR_VDD | 0.31 | – | – |
PP5V1_CHGR_VDDP | 0.31 | – | – |
PP18V5_Z2 | 0.57 | – | – |
PPCHGR_DCIN | 0.59 | – | – |
PPVIN_S5_HS_OTHER_ISNS | 0.44 | – | – |
PPVOUT_S0_LCDBKLT | 0.59 | – | – |
PSOC_F_CS_L | 0.70 | – | – |
PSOC_MISO | 0.70 | – | – |
PSOC_MOSI | 0.70 | – | – |
PSOC_SCLK | 0.70 | – | – |
S5_PWRGD | 0.56 | – | – |
SMBUS_SMC_2_S3_SCL | 0.70 | – | – |
SMBUS_SMC_2_S3_SDA | 0.58 | – | – |
SMBUS_SMC_5_G3_SCL | 0.52 | – | – |
SMBUS_SMC_5_G3_SDA | 0.52 | – | – |
SMC_BC_ACOK | 0.48 | – | – |
SMC_BIL_BUTTON_L | 0.74 | – | – |
SMC_LID_R | 0.82 | – | – |
SMC_PM_G2_EN | 0.52 | – | – |
UNCONNECTED_161 | OL | – | – |
UNCONNECTED_162 | OL | – | – |
UNCONNECTED_387 | OL | – | – |
WS_CONTROL_KBD | 0.46 | – | – |
WS_KBD_ONOFF_L | 1.48 | – | – |
WS_KBD1 | 0.70 | – | – |
WS_KBD2 | 0.70 | – | – |
WS_KBD3 | 0.70 | – | – |
WS_KBD4 | 0.70 | – | – |
WS_KBD5 | 0.70 | – | – |
WS_KBD6 | 0.70 | – | – |
WS_KBD7 | 0.70 | – | – |
WS_KBD8 | 0.70 | – | – |
WS_KBD9 | 0.70 | – | – |
WS_KBD10 | 0.70 | – | – |
WS_KBD11 | 0.70 | – | – |
WS_KBD12 | 0.70 | – | – |
WS_KBD13 | 0.70 | – | – |
WS_KBD14 | 0.70 | – | – |
WS_KBD15_CAP | 1.10 | – | – |
WS_KBD16_NUM | OL | – | – |
WS_KBD17 | 0.70 | – | – |
WS_KBD18 | 0.70 | – | – |
WS_KBD19 | 0.70 | – | – |
WS_KBD20 | 0.70 | – | – |
WS_KBD21 | 0.70 | – | – |
WS_KBD22 | 0.70 | – | – |
WS_KBD23 | 0.70 | – | – |
WS_LEFT_OPTION_KBD | 0.46 | – | – |
WS_LEFT_SHIFT_KBD | 0.46 | – | – |
Z2_BOOST_EN | 1.24 | – | – |
Z2_CLKIN | 0.70 | – | – |
Z2_CS_L | 0.70 | – | – |
Z2_DEBUG3 | 0.70 | – | – |
Z2_HOST_INTN | 0.70 | – | – |
Z2_KEY_ACT_L | 0.70 | – | – |
Z2_MISO | 0.70 | – | – |
Z2_MOSI | 0.70 | – | – |
Z2_RESET | 0.70 | – | – |
Z2_SCLK | 0.70 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PP3V42_G3H read on the 820-3330?
OpenBoardData's known-good values for PP3V42_G3H on the 820-3330: diode 0.35. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP5V_S5 read on the 820-3330?
OpenBoardData's known-good values for PP5V_S5 on the 820-3330: diode 0.45. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S0 read on the 820-3330?
OpenBoardData's known-good values for PP3V3_S0 on the 820-3330: diode 0.29. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-3330 board?
Open your own 820-3330 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License