Apple desktop board · OpenBoardData

820-3299 known-good readings

Known-good readings for the Apple desktop board 820-3299: 966 nets, including 93 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 92 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3299.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 93 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 14

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP1V2_G3H_SMC_VDDC0.528––
AI: what PP1V2_G3H_SMC_VDDC is and how to check it

PP1V2_G3H_SMC_VDDC is a 1.2 V rail; the G3H part of the name indicates it is always on, and SMC_VDDC suggests it supplies the SMC. The archive lists a known-good diode reading of 0.528 to ground, with no condition noted; there is no known-good voltage reading here.

  • With the board unpowered, measure diode mode from the rail to ground and compare with 0.528.
  • With power applied, measure the voltage; expect about 1.2 V from the name, but that is general, not a recorded value.

A diode reading far below 0.528 usually points to a short or a failing part on the rail; a far higher or open reading suggests a broken connection. Confirm with a second measurement before replacing anything.

PP3V3_G30.568––
AI: what PP3V3_G3 is and how to check it

PP3V3_G3 is a 3.3 V rail; the G3H tag in its name marks it as an always-on rail, present whenever the board has power. The archive lists a known-good diode reading of 0.568 to ground, with no condition noted, and no known-good voltage reading. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.568 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP3V3_G3H_AVREF_SMC0.603––
AI: what PP3V3_G3H_AVREF_SMC is and how to check it

PP3V3_G3H_AVREF_SMC is a 3.3 V rail; the G3H part of the name indicates it is always-on, and AVREF_SMC suggests it is a reference supply for the SMC. The only known-good figure here is a diode reading of 0.603 to ground, with no condition recorded; no known-good voltage reading is available.

  • Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage on the net.
  • A diode reading far from 0.603 usually points to a short or a leaky part on that net, but one reading alone doesn't confirm a bad part.
  • With no known-good voltage listed, compare against a matching always-on 3.3 V rail or a known-good board of the same model.
PP3V3_G3H_BT_FET0.507––
AI: what PP3V3_G3H_BT_FET is and how to check it
  • What it is: From the name, PP3V3_G3H_BT_FET is a 3.3 V always-on rail (G3H) associated with the Bluetooth FET. It's a name-based reading only; the parts on this net aren't documented here.
  • Known-good reading: diode 0.507 to ground, from the community archive. That's a guide, not a spec, and it varies with board state.
  • How to check: power off and unplug, then measure diode mode from the net to ground. Then apply power and measure the voltage, expecting about 3.3 V.
  • If it's far off: a diode reading well below known-good often suggests a shorted load on the rail; a missing or low voltage with a normal diode reading points more toward the supply side. No known-good voltage reading exists here, so compare against a matching always-on 3.3 V rail or a known-good board.
PP3V3_G3H_BT_FLT0.507––
AI: what PP3V3_G3H_BT_FLT is and how to check it

PP3V3_G3H_BT_FLT — the name indicates a 3.3 V rail in the always-on (G3H) startup stage, with "BT" and "FLT" suggesting a Bluetooth-related filtered branch. That reading is from the name, not from a schematic.

  • Known-good: diode 0.507 to ground (archive value, no condition recorded). No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power up and measure the voltage at the rail.
  • Far from 0.507: a much lower diode reading usually points to a short or leaky part on the rail; a much higher one to an open trace or missing feed. Confirm with a voltage check before replacing anything.
PP3V3_G3H_SMC_USBMUX_R0.318––
AI: what PP3V3_G3H_SMC_USBMUX_R is and how to check it
  • What it is: PP3V3_G3H_SMC_USBMUX_R is a 3.3 V always-on rail, from its name (G3H = always on). The SMC and USBMUX parts of the name suggest it feeds the SMC and USB multiplexer area, but the parts on it aren't known here.
  • Known-good reading: diode 0.318 to ground, from the readings archive (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a correct diode reading with no voltage points back toward the rail's source. Confirm with a second measurement before replacing anything.
PP3V3_G3H_SMC_VDDA0.326––
AI: what PP3V3_G3H_SMC_VDDA is and how to check it

PP3V3_G3H_SMC_VDDA is a 3.3 V always-on rail feeding the SMC's analog supply; the G3H part of the name indicates it should be present whenever the board has power, and the SMC_VDDA part is from the name. The only known-good reading here is a diode value of 0.326 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode, red probe on ground and black on the rail, then apply power and measure the voltage. A diode reading far from 0.326 suggests a short or a damaged component on the rail, but a small difference can be normal, so compare against a matching rail before condemning anything.

PP3V42_G3H0.326––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail on this board; the "G3H" in the name indicates it is always present when power is connected. The readings archive lists a known-good diode reading of 0.326 to ground, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. No known-good voltage reading is listed here, so compare against a matching rail on a known-good board. A diode reading far from 0.326 usually points to a short or a damaged component on that rail, but one reading alone doesn't confirm a fault.

PP3V42_G3H_SMC_SPVSR0.371––
AI: what PP3V42_G3H_SMC_SPVSR is and how to check it

PP3V42_G3H_SMC_SPVSR is the always-on 3.42 V rail feeding the SMC's SPVSR section, based on the G3H and SMC parts of its name. The only known-good reading here is a diode value of 0.371 to ground, with no condition listed; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the net to ground, then power the board and measure the DC voltage on the same net. A diode reading far below 0.371 suggests a short or leaky part on the rail; a reading far above it can mean an open trace or missing connection. This is a guide only, so confirm against a matching net or a known-good board before replacing anything.

PP12V_G3H0.568––
AI: what PP12V_G3H is and how to check it
  • What it is: PP12V_G3H is a 12 V rail; the G3H suffix means "always on" (from the name), so it should be present whenever the board has power.
  • Known-good reading: diode 0.568 to ground (community archive, condition not stated). No known-good voltage reading here.
  • How to check: power off, measure diode mode from PP12V_G3H to ground; then power up and measure the voltage at the rail.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; no voltage with a normal diode reading points upstream to the supply that creates it. Treat these as likely causes, not confirmed.
PP12V_G3H_P3V420.570––
AI: what PP12V_G3H_P3V42 is and how to check it

PP12V_G3H_P3V42 — reference note

  • From its name, this is a 12 V rail that is always on (G3H) and is tied to the P3V42 startup supply. The name alone doesn't confirm the exact circuit arrangement.
  • Known-good from the readings archive: diode mode to ground 0.570. That is the only known-good value recorded here; there is no known-good voltage or resistance reading for this rail.
  • Check it with the board unpowered: diode mode, black probe on ground, red on the rail. Then power the board and measure the DC voltage at the rail.
  • A diode reading far below 0.570 usually points to a short or a leaky part on that rail; a reading well above it can mean an open trace or missing connection. Confirm with a second measurement before replacing anything.
PPVBATT_G3_RTCOL––
AI: what PPVBATT_G3_RTC is and how to check it
  • What it is: From the name, PPVBATT_G3_RTC is the always-on (G3H) rail that keeps the RTC running, likely from the backup battery. No board file is available, so the parts on it aren't known.
  • Known-good readings: The archive lists diode OL for PPVBATT_G3_RTC. No known-good voltage or resistance reading is available here.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with the OL reading. Then apply power and measure the rail's voltage.
  • What a far-off reading suggests: A diode reading well below OL can mean a low-resistance path or a shorted part on the rail, but one reading doesn't confirm a bad part. Check the backup battery and its path first, since this rail is usually fed from it.
PPVBATT_G3_RTC_ROL––
AI: what PPVBATT_G3_RTC_R is and how to check it

PPVBATT_G3_RTC_R is the always-on RTC backup rail, judged from its name (G3H = always on); it typically keeps the real-time clock alive from the backup battery. The only known-good reading recorded here is a diode value of OL to ground, with the board unpowered. Check it the same way: power off, diode mode from the rail to ground, then measure its voltage with power applied. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode reading far below OL usually suggests a short or leaky part on that rail, but one reading isn't proof.

PPVOUT_G3_PCH_DCPRTC0.630––
AI: what PPVOUT_G3_PCH_DCPRTC is and how to check it

PPVOUT_G3_PCH_DCPRTC is an always-on G3H rail (from its name), likely a PCH-related supply on this 820-3299. The archive lists a known-good diode reading of 0.630 to ground, with no condition noted; there is no known-good voltage reading here. Check it unpowered in diode mode, red probe on ground, black on the rail, then measure the voltage with power applied and compare against a matching rail or a known-good board. A diode reading far below 0.630 usually points to a short or leaky load on the rail, while a much higher one can mean an open path; confirm with a second reading before condemning anything.

S5 and SUS: standby 5

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP3V3_S50.150––
AI: what PP3V3_S5 is and how to check it

PP3V3_S5 is a 3.3 V standby rail; the S5/SUS suffix, from its name, places it in the standby stage that should be present before the board fully powers on. The only known-good reading here is a diode value of 0.150 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then apply power and measure the voltage. No known-good voltage reading is available here, so compare against a matching standby rail or a known-good board. A diode reading far from 0.150 usually points to a short or leak on that rail, but one reading alone doesn't confirm a bad part.

PP3V3_S5_XDP_R0.101––
AI: what PP3V3_S5_XDP_R is and how to check it

PP3V3_S5_XDP_R is a 3.3 V standby rail; the S5/SUS part of the name marks it as a standby rail (that reading is from the name, not the board data). The archive lists one known-good diode reading of 0.101 to ground, with no condition noted, and no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. A diode reading far from 0.101 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S50.400––
AI: what PP5V_S5 is and how to check it

PP5V_S5 is the 5 V standby rail (S5/SUS, from the name) on the 820-3299. The only known-good reading here is a diode value of 0.400 to ground; no known-good voltage reading is available.

  • With the board unpowered, measure diode mode from PP5V_S5 to ground and compare with 0.400.
  • With power applied, measure the rail voltage; the expected level isn't in this data, so compare against a known-good board or the rail's nominal 5 V.
  • A diode reading far below 0.400 usually points to a short or leaky load on the rail; far above can mean an open path.
PP5V_S5_PCH_V5REFSUS0.392––
AI: what PP5V_S5_PCH_V5REFSUS is and how to check it

PP5V_S5_PCH_V5REFSUS — from the name, this is a 5 V standby rail (S5, SUS) feeding the PCH's 5 V reference supply. It sits in the standby stage, so it should be present before the board fully powers on.

  • Known-good: diode 0.392 to ground, board unpowered. No known-good voltage reading here.
  • Check: power off, measure diode mode from the rail to ground; then power up and measure the DC voltage at the rail.
  • A diode reading far from 0.392 usually points to a short or a leaky load on the rail; a missing or low voltage with a good diode reading points upstream at the rail's source or enable.
PP12V_S50.527––
AI: what PP12V_S5 is and how to check it
  • What it is: PP12V_S5 is a 12 V standby rail; the "S5" part of the name indicates it belongs to the standby stage, so it should be present before the board fully powers on. This is from the name only.
  • Known-good reading: diode 0.527 to ground, from the readings archive (community-contributed, so a guide, not a spec). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from PP12V_S5 to ground and compare with 0.527. Then apply power and measure the DC voltage on the rail; there's no archived voltage value to compare against, so use a known-good board or the rail's expected 12 V as a general guide.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail, and no or wrong voltage with power applied points to the supply or enable side feeding it. Confirm with a second measurement before replacing anything.

S4 26

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP1V2_S4_CAMERA0.379––
AI: what PP1V2_S4_CAMERA is and how to check it

PP1V2_S4_CAMERA (820-3299) — reference note

  • From the name, this is a 1.2 V rail in the S4 (startup) power stage, feeding the camera section. That meaning is inferred from the rail name, not from board data.
  • Known-good reading in the archive: diode mode to ground 0.379, with no condition recorded. No known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground. Power up and measure the voltage at the rail.
  • A diode reading far from 0.379 usually points to a short or a leaky load on the rail; a missing or low voltage with a normal diode reading points more toward the supply or enable side. Treat both as leads, not confirmed faults.
PP1V2_S4_ENET_PHY_AVDDL0.296––
AI: what PP1V2_S4_ENET_PHY_AVDDL is and how to check it
  • What it is: PP1V2_S4_ENET_PHY_AVDDL is a 1.2 V supply rail for the Ethernet PHY's analog low-voltage domain, judged from the name; the S4 tag places it in the S4 power state.
  • Known-good reading: diode 0.296 in the archive, with no condition recorded. No known-good voltage or resistance reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.296; then power up and measure the rail voltage, expecting about 1.2 V from the name.
  • If it's far off: a much lower diode reading suggests a short or leaky load on the rail, while an open or high reading points to a missing feed or enable. Treat these as likely causes, not confirmed ones, and check the feed and enable before replacing anything.
PP1V2_S4_ENET_PHY_GPHYPLL0.296––
AI: what PP1V2_S4_ENET_PHY_GPHYPLL is and how to check it
  • What it is: From the name, a 1.2 V rail (PP1V2) in the S4 power state, feeding the Ethernet PHY's GPHY PLL. That's an interpretation of the name, not from board data.
  • Known-good reading: diode 0.296 in the readings archive. No known-good voltage or resistance is recorded here.
  • How to check: With the board unpowered, diode mode from the rail to ground; then power up and measure the rail voltage.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open trace or missing part. The archive gives no voltage reference, so compare against a known-good board.
PP1V2_S4_ENET_PHY_PCIEPLL0.296––
AI: what PP1V2_S4_ENET_PHY_PCIEPLL is and how to check it
  • What it is: From the name, a 1.2 V rail (PP1V2) in the S4 power state, feeding the Ethernet PHY and PCIe PLL. The board data only names the net; it doesn't list which parts sit on it.
  • Known-good reading: diode 0.296 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground and compare with 0.296. Then power on and measure the rail voltage; the data has no expected value for that, so compare against a known-good board or the rail's nominal 1.2 V.
  • If far off: a much lower diode reading usually points to a short or leaky part on the rail; an open or high reading points to a missing supply or broken trace. Confirm with the voltage measurement before replacing anything.
PP1V8_S4_CAMERA0.438––
AI: what PP1V8_S4_CAMERA is and how to check it

PP1V8_S4_CAMERA is a 1.8 V rail in the S4 startup stage, judging from its name; the archive lists one known-good diode reading of 0.438 to ground. To check it, power the board off and measure diode mode from the rail to ground, then power up and measure its voltage. No known-good voltage reading is recorded here, so compare against a matching 1.8 V rail or a known-good board. A diode reading far from 0.438 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PP1V8_S4_CAMERA_F0.438––
AI: what PP1V8_S4_CAMERA_F is and how to check it

PP1V8_S4_CAMERA_F is a 1.8 V camera rail; the "S4" in its name marks it as a later startup stage, and that reading is from the name, not from board data. The archive lists a known-good diode reading of 0.438 to ground, with no condition noted and no known-good voltage reading here. With the board unpowered, measure diode mode from the rail to ground and compare; then power up and check the voltage. A diode reading far from 0.438 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad part.

PP3V3_S40.340––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 power stage, judged from its name; the archive gives no part list for it. The only known-good reading here is diode mode to ground, 0.340, with no condition recorded; there is no known-good voltage reading here. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.340 usually points to a short or a leaky load on the rail, but one reading isn't proof — compare against a matching rail or a known-good board before replacing anything.

PP3V3_S4_ALS_F0.340––
AI: what PP3V3_S4_ALS_F is and how to check it

PP3V3_S4_ALS_F is a 3.3 V rail in the S4 power state, and the ALS suffix suggests it feeds the ambient light sensor — that part is from the name, not from board data. The archive lists one known-good reading: diode 0.340, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on it. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.340 usually points to a short or a leaky load on the rail; a far higher one can mean an open path — either is a lead to trace, not a confirmed fault.

PP3V3_S4_AP0.340––
AI: what PP3V3_S4_AP is and how to check it

PP3V3_S4_AP is a 3.3 V rail that comes up at the S4 startup stage, judging from its name. The archive lists one known-good diode reading, 0.340, with no condition noted, and no known-good voltage reading here. With the board unpowered, measure diode mode from PP3V3_S4_AP to ground and compare with 0.340; then power up and check the voltage. A diode reading far from 0.340 usually points to a short or a damaged part on the rail, but one reading alone doesn't confirm a fault.

PP3V3_S4_AP_FET0.508––
AI: what PP3V3_S4_AP_FET is and how to check it

PP3V3_S4_AP_FET is a 3.3 V rail that comes up at the S4 stage of startup, judging by its name; the "FET" suffix suggests it is switched through a FET. The only known-good reading here is a diode value of 0.508 to ground, with no condition recorded, and there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far from 0.508 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare against a matching rail or a known-good board.

PP3V3_S4_AP_FLT0.508––
AI: what PP3V3_S4_AP_FLT is and how to check it

PP3V3_S4_AP_FLT is a 3.3 V rail from its name, in the S4 startup stage, likely a filtered ("FLT") supply for the AP section — that's from the name only, not confirmed by board data. The only known-good reading here is a diode value of 0.508 to ground; no known-good voltage reading is available. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.508 suggests a short or leaky load on the rail; a far higher or open reading suggests a broken path — treat both as a guide and confirm before replacing anything.

PP3V3_S4_CAMFILT0.343––
AI: what PP3V3_S4_CAMFILT is and how to check it

PP3V3_S4_CAMFILT (820-3299) — reference note

  • From the name: a 3.3 V rail in the S4 power state, filtered for the camera circuit. "S4" is a sleep/startup stage, so it should come up after the main rails and before full S0.
  • Known-good: diode-to-ground reading of 0.343 in the archive. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then apply power and measure the voltage on the rail.
  • A diode reading far below 0.343 usually points to a short or a leaky part on the rail; far above it can mean an open trace or missing connection. Confirm with voltage under power before replacing anything.
PP3V3_S4_ENET0.365––
AI: what PP3V3_S4_ENET is and how to check it

PP3V3_S4_ENET is an S4-stage 3.3 V rail; the "ENET" suffix suggests it feeds Ethernet-related circuitry, though that's from the name only and not confirmed by board data. The only known-good reading here is a diode value of 0.365 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage reading is available for this rail. A diode reading far from 0.365 usually points to a short or a damaged component on the rail, but confirm with a voltage check before replacing anything.

PP3V3_S4_ENET_FET_AVDDH0.365––
AI: what PP3V3_S4_ENET_FET_AVDDH is and how to check it
  • What it is: From the name, a 3.3 V rail (PP3V3) in the S4 power state, feeding the Ethernet PHY analog high-side supply (ENET_FET_AVDDH). The exact parts on it aren't documented here.
  • Known-good reading: diode 0.365 in the archive, no condition recorded. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a missing voltage points upstream to the S4 enable or the FET feeding it. Treat this as a guide, not a confirmed fault.
PP3V3_S4_ENET_FET_BIASVDDH0.365––
AI: what PP3V3_S4_ENET_FET_BIASVDDH is and how to check it
  • What it is: From the name, a 3.3 V rail in the S4 power state, tied to the Ethernet (ENET) FET bias supply (BIASVDDH). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.365 to ground, from the readings archive. That's a community guide, not a guaranteed value; no known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the net to ground and compare with 0.365. Then power up and measure the DC voltage; no known-good voltage is recorded, so compare against a matching rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a shorted part or a damaged FET on that net; a much higher one to an open trace or missing part. Confirm with a second measurement before replacing anything.
PP3V3_S4_ENET_FET_XTALVDDH0.365––
AI: what PP3V3_S4_ENET_FET_XTALVDDH is and how to check it
  • What it is: From the name, a 3.3 V rail in the S4 startup stage, feeding the Ethernet section and the crystal/oscillator supply (XTALVDDH) through a FET. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.365 in the archive, no stated condition; treat it as a guide only. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a missing voltage points to the enable or the FET feeding it.
PP5V_S40.157––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judging from its name. The only known-good reading here is a diode value of 0.157 to ground; there is no known-good voltage reading for this rail.

  • Check it unpowered in diode mode from PP5V_S4 to ground and compare with 0.157.
  • Then power the board and measure the voltage on PP5V_S4; the expected level is about 5 V from the name, not from a recorded reading.

A diode reading far from 0.157 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a bad part. If the rail is missing with power applied, trace back through the S4 enable and the supply feeding it.

PP5V_S4_CAMERA_F0.157––
AI: what PP5V_S4_CAMERA_F is and how to check it

PP5V_S4_CAMERA_F is a 5 V rail for the camera circuit, enabled at the S4 stage of startup — that reading comes from the rail's name, not from a schematic. The only known-good figure here is a diode reading of 0.157 to ground, with the board unpowered. Check it in diode mode from the rail to ground first, then measure the voltage on the rail with power applied; no known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.157 usually points to a short or a leaky component on that rail, but one reading alone doesn't confirm a bad part.

PP5V_S4_EXTA0.526––
AI: what PP5V_S4_EXTA is and how to check it

PP5V_S4_EXTA is a 5 V rail in the S4 startup stage, judged from its name; the parts it feeds aren't known here. The only known-good reading is a diode value of 0.526 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far below 0.526 usually points to a short or a leaky load on the rail, while a far higher one can mean an open path; confirm with a second measurement before replacing anything.

PP5V_S4_EXTA_F0.526––
AI: what PP5V_S4_EXTA_F is and how to check it

PP5V_S4_EXTA_F is a 5 V rail in the S4 startup stage, judging from its name (the S4 suffix and the 5V prefix); the exact loads on it aren't documented here.

  • Known-good: diode reading 0.526 to ground, from the readings archive. No known-good voltage reading here.
  • Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail.
  • A diode reading far below 0.526 usually points to a shorted or leaky load on the rail; a much higher one can mean an open path. Confirm with a second measurement before replacing anything.
PP5V_S4_EXTB0.527––
AI: what PP5V_S4_EXTB is and how to check it

PP5V_S4_EXTB is a 5 V rail that, from its name, belongs to the S4 startup stage and likely feeds external-bus circuitry. The only known-good reading here is a diode value of 0.527; there is no known-good voltage reading in this data.

  • Check with the board unpowered: diode mode, red probe on ground, black on the rail, and compare with 0.527.
  • Then power the board and measure the DC voltage on the rail.
  • A diode reading far below 0.527 suggests a short or a leaky load on the rail; far above it can mean an open path. Treat one reading as a guide only, and confirm before replacing anything.
PP5V_S4_EXTB_F0.526––
AI: what PP5V_S4_EXTB_F is and how to check it

PP5V_S4_EXTB_F is a 5 V rail in the S4 startup stage, judging from its name (general naming convention, not from board data). The archive lists a diode reading of 0.526 to ground for this net; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from the rail to ground and compare against 0.526. Then power up and check the voltage at the rail. A diode reading far below 0.526 usually points to a short or a leaky load on the rail, while a much higher reading can mean an open trace or missing connection; confirm with a voltage check before replacing anything.

PP5V_S4_EXTC0.529––
AI: what PP5V_S4_EXTC is and how to check it
  • What it is: PP5V_S4_EXTC is a 5 V rail in the S4 startup stage, both from its name. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.529 to ground, no condition recorded. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then power up and measure the DC voltage. Compare against 0.529.
  • If it's far off: a much lower diode reading usually suggests a short or leaky part on the rail; a much higher one an open path. Treat it as a guide and confirm before replacing anything.
PP5V_S4_EXTC_F0.529––
AI: what PP5V_S4_EXTC_F is and how to check it

PP5V_S4_EXTC_F — reference note

  • What it is: a 5 V rail in the S4 startup stage, from the rail name (S4 = a later power state in the usual Apple sequence; EXTC likely an external/connector-related branch). The parts on this net aren't documented here.
  • Known-good reading: diode 0.529 to ground, from the community archive; treat it as a guide, not a spec.
  • How to check: power off and unplug, then diode mode from the rail to ground. Then power up and measure the DC voltage — no known-good voltage is recorded here, so compare against a matching rail on the other side of a pair or a known-good board.
  • If it's far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; an open or high reading points to a missing feed or broken trace. Confirm with a voltage measurement before replacing anything.
PP5V_S4_EXTD0.528––
AI: what PP5V_S4_EXTD is and how to check it

PP5V_S4_EXTD is a 5 V rail in the S4 startup stage, judging by its name; the "EXTD" suffix suggests it feeds external or extended circuitry, though that's general interpretation, not from board data.

  • Known-good: diode reading 0.528 to ground (condition not stated in the data). No known-good voltage reading here.
  • Check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • A diode reading far below 0.528 usually points to a short or leaky load on the rail; a far higher or open reading points to a broken path or missing part. Confirm with a second measurement before replacing anything.
PP5V_S4_EXTD_F0.528––
AI: what PP5V_S4_EXTD_F is and how to check it

PP5V_S4_EXTD_F is a 5 V rail in the S4 startup stage, from its name; the "EXTD" part suggests it's an externally derived or extended 5 V, but that's general reading, not from the data. The only known-good reading here is a diode value of 0.528 to ground, with no condition noted; there is no known-good voltage reading for this rail. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage. A diode reading far from 0.528 usually points to a short or leaky component on the rail, but one reading doesn't confirm a bad part; compare with a matching rail or a known-good board before replacing anything.

S3: memory 2

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PPVDDQ_S30.335––
AI: what PPVDDQ_S3 is and how to check it
  • What it is: PPVDDQ_S3 is the S3-state DDR memory rail; the S3 and VDDQ parts of the name indicate a memory supply (from the name, not from board data).
  • Known-good reading: diode 0.335 to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power up and measure the rail voltage.
  • If far off: a low diode reading usually points to a shorted load or capacitor on the rail; a high or open reading points to a missing supply or broken trace. Confirm with a second measurement before replacing anything.
PPVDDQ_S3_DDR0.343––
AI: what PPVDDQ_S3_DDR is and how to check it
  • What it is: PPVDDQ_S3_DDR is the DDR memory rail that comes up at the S3 stage — that reading is from the name, not from a schematic. It's the supply for the board's DDR memory.
  • Known-good reading: diode 0.343 to ground, from the community archive. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.343. Then power up and measure the rail voltage; since no known-good voltage is listed, compare against a matching rail or a known-good board.
  • If it's far off: a much lower diode reading usually points to a short or a failing part on the rail, while an open or high reading points to a broken feed. Treat 0.343 as a guide only, since readings vary with board state.

S0: running 46

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V05_S00.045–44.000R
AI: what PP1V05_S0 is and how to check it
  • What it is: PP1V05_S0 is a 1.05 V rail that runs in the S0 (running) state, from its name. It's a low-voltage supply, typically a core or memory-type rail (general).
  • Known-good readings (community guide): diode 0.045 and resistance 44.000R. No known-good voltage reading here.
  • How to check: with the board unpowered, diode mode from the rail to ground; then power up and measure the voltage.
  • If far off: a much lower diode/resistance suggests a short or leaky load on the rail; a much higher one suggests an open feed. Confirm with a voltage check before replacing anything.
PP1V5_S00.130––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the S0 suffix, from its name, marks it as a running-state supply rather than a standby one. The only known-good reading here is diode mode to ground: 0.130, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then with power applied confirm about 1.5 V. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.130 usually points to a short or a leaky load on the rail, but one reading doesn't confirm a bad part.

PP1V05_S0_CPU0.011––
AI: what PP1V05_S0_CPU is and how to check it

PP1V05_S0_CPU is a 1.05 V supply rail for the CPU, and the S0 in its name marks it as a running-state rail (both from the name).

  • Known-good: diode 0.011 to ground. No known-good voltage reading here.
  • Check with the board unpowered: diode mode, red probe on ground, black on the rail. Then power up and measure the voltage on the rail.
  • A diode reading far from 0.011 usually points to a short or a leaky load on the rail, not proof of a bad part; compare against a matching rail or a known-good board before replacing anything.
PP1V5_S0_CPU_MEM0.130–128.000R
AI: what PP1V5_S0_CPU_MEM is and how to check it

PP1V5_S0_CPU_MEM is a 1.5 V rail feeding CPU memory, judged from its name; the S0 suffix indicates it belongs to the running (S0) power state. Known-good readings in the archive are a diode reading of 0.130 and 128.000R to ground, with the board unpowered. Check it in diode mode to ground first, then measure the voltage with the board powered and running. A diode or resistance reading far from these usually points to a short or a damaged load on the rail, but a single reading isn't proof a part is bad. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board.

PP1V05_S0_PCH0.045––
AI: what PP1V05_S0_PCH is and how to check it

PP1V05_S0_PCH is a 1.05 V rail, from its name: the S0 (running) supply for the PCH. The archive lists one known-good reading: diode 0.045 to ground (board unpowered, no condition noted). No known-good voltage reading here.

  • Check: power off, measure diode mode from the rail to ground; then power on and measure the voltage at the rail.
  • A diode reading far above 0.045 usually points to an open feed (inductor, fuse or trace) rather than a short; far below suggests a shorted load on the rail.
  • No known-good voltage is recorded, so compare against a matching rail on a known-good board.
PP1V8_S00.211––
AI: what PP1V8_S0 is and how to check it

PP1V8_S0 is a 1.8 V rail that is on in the S0 (running) state, judging by its name. The only known-good figure here is a diode reading of 0.211 to ground; no known-good voltage reading is recorded.

  • With the board unpowered, measure diode mode from PP1V8_S0 to ground and compare with 0.211.
  • Then power the board and confirm roughly 1.8 V is present once it reaches S0.

A diode reading far below 0.211 suggests a short or a leaky load on the rail; far above it suggests an open path. A missing or low voltage with a normal diode reading points more toward the rail's supply or enable than the rail itself. These are general guidelines, not confirmed causes for this board.

PP3V3_S00.289––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is a 3.3 V rail; the S0 suffix, from its name, marks it as a running-state supply (general naming convention, not board-specific data). The only known-good reading here is a diode value of 0.289, with no condition recorded and no voltage reading in the data.

  • Check it unpowered in diode mode from PP3V3_S0 to ground; compare with 0.289 as a guide.
  • Then power the board and measure the voltage on the rail; no known-good voltage is listed here, so compare against a known-good board or the rail's nominal 3.3 V.
  • A diode reading far below 0.289 suggests a short or a leaky load on the rail; far above suggests an open path. Neither confirms a bad part on its own, so trace the rail's branches before replacing anything.
PP3V3_S0_BLC_R0.289––
AI: what PP3V3_S0_BLC_R is and how to check it

PP3V3_S0_BLC_R is a 3.3 V rail; the name suggests S0 (running state) and a backlight-related supply, though that's from the name only. The archive gives one known-good reading: diode 0.289 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. No known-good voltage reading exists here, so compare against a matching rail or a known-good board. A diode reading far from 0.289 usually points to a short or a leaky part on that rail, but confirm with a voltage measurement before replacing anything.

PP3V3_S0_SSD0.289––
AI: what PP3V3_S0_SSD is and how to check it

PP3V3_S0_SSD is a 3.3 V rail for the SSD section, and the S0 in its name indicates it belongs to the running (S0) power state. The only known-good figure here is a diode reading of 0.289 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.289 usually points to a short or a damaged component on that rail, but a single reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S0_SSD_FLT0.289––
AI: what PP3V3_S0_SSD_FLT is and how to check it

PP3V3_S0_SSD_FLT — from the name, a 3.3 V rail (PP3V3) that is up in the S0 running state, associated with the SSD and likely a fault or filter node (FLT). The archive lists one known-good diode reading of 0.289 to ground; there is no known-good voltage reading here.

  • Check with power off: diode mode from the rail to ground, red probe on ground. Compare with 0.289; a much lower reading suggests a short or leaky part on the rail, a much higher one an open path.
  • Check with power on: measure the voltage at the rail in the S0 state. No known-good voltage is recorded, so compare against a matching rail on a known-good board.
  • A reading far from known-good points to a fault on that net, but one reading alone doesn't confirm a bad part — trace it before replacing anything.
PP3V3_S0_SW_SD_PWR0.558––
AI: what PP3V3_S0_SW_SD_PWR is and how to check it

PP3V3_S0_SW_SD_PWR — reference note

  • From the name, this is a 3.3 V rail (PP3V3) that is switched (SW) and feeds SD card power (SD_PWR), active in the S0 running state.
  • Known-good reading in the archive: diode 0.558 to ground, board unpowered. No known-good voltage reading here.
  • To check: power off, measure diode mode from the rail to ground and compare with 0.558; then power on and measure the voltage at the rail, which should sit near 3.3 V when the board is in S0.
  • A diode reading far below 0.558 suggests a short or leaky load on the rail; far above suggests an open path. A missing voltage with a normal diode reading points to the switch or its enable, not the load. These are guides only, not confirmed faults.
PP5V_S00.363––
AI: what PP5V_S0 is and how to check it
  • What it is: PP5V_S0 is the 5 V rail that is present in the S0 (running) state, from its name. It's a main logic-board supply, not a standby rail.
  • Known-good reading: diode 0.363 to ground, from the readings archive. This is a guide only; the archive gives no voltage value for this rail, so there's no known-good voltage here.
  • How to check: with the board unpowered, measure diode mode from PP5V_S0 to ground and compare with 0.363. Then power up and measure the voltage on the rail.
  • What a far-off reading suggests: a diode reading well below known-good points to a short or a leaky part on the rail; a much higher or open reading points to a broken connection or a missing source. Confirm with the voltage measurement before replacing anything.
PP5V_S0_BLC_R0.366––
AI: what PP5V_S0_BLC_R is and how to check it

PP5V_S0_BLC_R is a 5 V rail, from its name: the S0 state means it's present while the board is running, and BLC points to the backlight circuit. The only known-good reading here is a diode reading of 0.366 to ground; no known-good voltage reading is recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.366 usually suggests a short or a leaky load on the rail, but one reading isn't proof, so compare with a matching rail or a known-good board before replacing anything.

PP5V_S0_GPU_VCORE_VCC0.361––
AI: what PP5V_S0_GPU_VCORE_VCC is and how to check it

PP5V_S0_GPU_VCORE_VCC — reference note

  • From its name, this is a 5 V rail (PP5V) that is switched on in the S0 running state and feeds the GPU core supply area (GPU_VCORE_VCC). The name is the only source for that; no schematic data is available for this board.
  • Known-good reading in the archive: diode mode to ground 0.361, no condition recorded. There is no known-good voltage reading here.
  • To check it: power off and unplug, then measure diode mode from the rail to ground and compare with 0.361. Then power the board into S0 and measure the DC voltage at the rail.
  • A diode reading far below 0.361 usually points to a short or a failing load on the rail; far above it can mean an open path or a missing part. Confirm with the voltage measurement before replacing anything, since a single reading can mislead.
PP5V_S0_HDD0.363––
AI: what PP5V_S0_HDD is and how to check it

PP5V_S0_HDD is a 5 V rail that, from its name, is switched on in the S0 (running) state and feeds the drive. The archive lists one known-good reading: diode mode to ground 0.363, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading here, so compare against a matching 5 V S0 rail or a known-good board. A diode reading far below 0.363 usually points to a short or leaky part on the rail; far above it suggests an open path.

PP5V_S0_HDD_FET0.600––
AI: what PP5V_S0_HDD_FET is and how to check it

PP5V_S0_HDD_FET is a 5 V rail that, from its name, feeds the HDD section and is switched by a FET; the S0 part means it belongs to the running state. The only known-good reading here is a diode value of 0.600 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage; no known-good voltage reading is recorded for this rail. A diode reading far below 0.600 usually points to a short or a leaky part on that rail, while a much higher one can mean an open path. Treat the 0.600 as a guide only, since readings vary with board state.

PP5V_S0_PCH_V5REF0.366––
AI: what PP5V_S0_PCH_V5REF is and how to check it
  • What it is: From its name, PP5V_S0_PCH_V5REF is a 5 V rail that is present in the S0 (running) state and feeds the PCH's V5REF reference. The board data only has the net name and its startup stage, not the parts on it.
  • Known-good reading: diode 0.366 to ground, from the community archive (no condition recorded). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the net to ground and compare with 0.366. Then power up and measure the voltage; it should sit near 5 V in S0, though that's general expectation, not a recorded value.
  • If far off: a much lower diode reading usually suggests a short or leaky part on the rail; a much higher one can mean an open trace or missing part. Confirm with a second measurement before replacing anything.
PP12V_S00.444––
AI: what PP12V_S0 is and how to check it

PP12V_S0 — a 12 V rail that is on in the S0 (running) state, from its name.

  • Known-good: diode-to-ground reading 0.444 (community value, a guide; no condition recorded). No known-good voltage is recorded here.
  • Check with the board unpowered: diode mode, black probe on ground, red on the rail. Then power up and measure the rail voltage.
  • A diode reading far below 0.444 suggests a short or a leaky part on the rail; far above suggests an open path. Confirm with voltage before replacing anything.
PP12V_S0_BLC0.545––
AI: what PP12V_S0_BLC is and how to check it
  • What it is: From the name, PP12V_S0_BLC is a 12 V rail that is present in the S0 (running) state, and "BLC" suggests it feeds the backlight circuit. That is inferred from the name only; the parts on the net aren't known.
  • Known-good reading: diode 0.545 to ground, with no condition recorded. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the DC voltage.
  • If far from known-good: a much lower diode reading usually points to a short or leaky part on the rail; a correct diode reading with no voltage points upstream, to the rail's source or its enable.
PP12V_S0_BLC_F0.545––
AI: what PP12V_S0_BLC_F is and how to check it

PP12V_S0_BLC_F is a 12 V backlight rail that is present in the running (S0) state, judging from its name. The only known-good reading here is a diode value of 0.545 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far below 0.545 suggests a short or leaky load on the rail, while a much higher or open reading points to a broken connection; confirm with a second measurement before replacing anything.

PP12V_S0_BLC_VIN20.510––
AI: what PP12V_S0_BLC_VIN2 is and how to check it

PP12V_S0_BLC_VIN2 is a 12 V backlight supply rail, going by its name (12V, BLC for backlight, S0 for the running state). The archive lists one known-good diode reading of 0.510 to ground, with no condition recorded.

  • Check it unpowered in diode mode, red lead on ground, black on the rail, and compare with 0.510.
  • Then power the board and measure the DC voltage; no known-good voltage is recorded here, so compare against a matching backlight rail on a known-good board.
  • A diode reading far below 0.510 suggests a short or leaky part on the rail; far above suggests an open path. Neither confirms a bad part on its own, so check the voltage next.
PP12V_S0_BLC_VINP0.527––
AI: what PP12V_S0_BLC_VINP is and how to check it
  • What it is: From its name, PP12V_S0_BLC_VINP is a 12 V backlight-related rail that is present in the S0 (running) state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.527 to ground, from the readings archive. That's a community guide, not a factory spec, and it varies with board state. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on that rail; a much higher one to an open path. Confirm with a second measurement before replacing anything.
PP12V_S0_CPU_P1V050.444––
AI: what PP12V_S0_CPU_P1V05 is and how to check it
  • What it is: From its name, PP12V_S0_CPU_P1V05 is a CPU-related power rail active in the S0 (running) state. The "12V" and "1V05" in the name suggest a 12 V feed and a 1.05 V CPU level, but the exact role isn't confirmed by the available data.
  • Known-good reading: Diode mode to ground, 0.444. That is the only known-good value recorded here; there is no known-good voltage reading for this rail.
  • How to check: With the board unpowered, measure diode mode from the rail to ground and compare with 0.444. Then apply power and measure the rail voltage, comparing against a matching rail on a known-good board since no voltage value is listed.
  • If far off: A diode reading well below 0.444 can suggest a short or a failing component on the rail; a much higher reading can suggest an open connection. Confirm with a voltage measurement before replacing anything.
PP12V_S0_CPUCORE_FLT0.444––
AI: what PP12V_S0_CPUCORE_FLT is and how to check it

PP12V_S0_CPUCORE_FLT — reference note

  • What it is: from the name, a 12 V rail (PP12V) that is on in the S0 running state and feeds the CPU core section (CPUCORE), with FLT likely meaning a filtered or fault-related variant. The name is the only description available; the parts on this net aren't documented.
  • Known-good reading: diode-to-ground 0.444 in the archive, with no condition recorded. No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.444; then power up and measure the rail voltage, comparing against a known-good board since no voltage value is recorded.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. Treat a small difference as normal and confirm with a second measurement before replacing anything.
PP12V_S0_FAN_0_FILT0.444––
AI: what PP12V_S0_FAN_0_FILT is and how to check it

PP12V_S0_FAN_0_FILT is a 12 V fan rail; the "S0" in the name indicates it belongs to the running (S0) power state, and "FILT" suggests it is a filtered feed to the fan circuit.

  • Known-good reading: diode 0.444 to ground, board unpowered. No known-good voltage reading here.
  • Check it with the board off: diode mode, black probe on ground, red on the rail. Then power up and measure the DC voltage on the rail.
  • A diode reading far from 0.444 usually points to a short or a leaky part on that rail; a missing or low voltage under power points to the supply or enable side, not necessarily the fan itself.
PP12V_S0_FBVDDQ0.444––
AI: what PP12V_S0_FBVDDQ is and how to check it
  • What it is: From its name, PP12V_S0_FBVDDQ is a 12 V rail that is up in the S0 (running) state; the FBVDDQ part of the name suggests it feeds a memory-related supply. The archive has no board file, so which parts sit on this net isn't known.
  • Known-good reading: diode 0.444 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: with power off, measure diode mode from the rail to ground and compare with 0.444; then power up and measure the voltage, expecting about 12 V from the name.
  • If it's far off: a much lower diode reading usually points to a short or a failing load on the rail, while a missing voltage with a normal diode reading points upstream to the rail's source or its enable. These are general guidelines, not confirmed causes.
PP12V_S0_GPUCORE_FLT0.444––
AI: what PP12V_S0_GPUCORE_FLT is and how to check it
  • What it is: From the name, a 12 V rail (PP12V) that is on in the S0 running state and feeds the GPU core area; the FLT suffix suggests a filtered or fault-related branch. The exact parts on it aren't known here.
  • Known-good reading: diode 0.444 to ground, from the community archive — a guide only, since readings vary with board state.
  • How to check: power off and unplug, then measure diode mode from the rail to ground. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on that rail; no known-good voltage reading is recorded here, so compare against a matching rail or a known-good board before replacing anything.
PP12V_S0_HDD0.444––
AI: what PP12V_S0_HDD is and how to check it

PP12V_S0_HDD is a 12 V rail that, from its name, is switched on in the S0 (running) state and feeds the hard drive. The archive's known-good reading for it is a diode value of 0.444, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then with power applied measure its voltage; no known-good voltage reading is recorded here. A diode reading far below 0.444 usually points to a short or leaky load on the rail, while a much higher or open reading points to a broken path feeding it. Treat the 0.444 as a guide only, since readings vary with board state.

PP12V_S0_HDD_FET0.670––
AI: what PP12V_S0_HDD_FET is and how to check it

PP12V_S0_HDD_FET is a 12 V rail switched by a FET for the hard drive, and the S0 in its name indicates it's active in the running state. The only known-good figure here is a diode reading of 0.670 to ground, with no condition recorded; there is no known-good voltage reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage. A diode reading far below 0.670 usually points to a short or a leaky part on that rail, while a much higher or open reading suggests a broken connection; confirm with a voltage check before replacing anything.

PP12V_S0_P1V050.444––
AI: what PP12V_S0_P1V05 is and how to check it
  • What it is: From the name, PP12V_S0_P1V05 is a 12 V rail that is present in the S0 (running) state; the P1V05 suffix suggests a 1.05 V point it feeds or is derived from, but the exact topology isn't in the data.
  • Known-good reading: diode 0.444 to ground, from the readings archive (a community value, so treat it as a guide).
  • How to check: power off and check diode mode from the rail to ground, then power on and measure the DC voltage.
  • No known-good voltage reading here, so compare against a matching rail on a known-good board.
  • A diode reading far from 0.444 usually points to a short or leaky part on that rail; confirm with voltage and resistance before replacing anything.
PP12V_S0_VCCSA0.444––
AI: what PP12V_S0_VCCSA is and how to check it

PP12V_S0_VCCSA is a 12 V rail that, from its name, belongs to the S0 "running" power state. The only known-good figure here is a diode reading of 0.444 to ground; no known-good voltage reading is recorded. With the board unpowered, measure diode mode from the rail to ground and compare with 0.444, then power up and check the voltage. A diode reading far below 0.444 usually points to a short or a leaky part on the rail; a far higher or open reading can mean a broken connection. This is a guide only, since readings vary with board state, and a likely cause is not a confirmed one.

PPCPUAXG_S0_SENSE0.002––
AI: what PPCPUAXG_S0_SENSE is and how to check it

PPCPUAXG_S0_SENSE (820-3299)

  • What it is: From the name, a CPU-AXG sense line in the S0 (running) state. The archive doesn't list which parts sit on it, so treat that as name-based only.
  • Known-good reading: diode 0.002 to ground, with no condition recorded. That is a very low value, so confirm it on a known-good board before judging a part.
  • How to check: power off and unplug, then diode-mode from the net to ground; then power up and measure the voltage on it. No known-good voltage reading here.
  • If it's far off: a much higher diode reading usually points to an open trace or missing part; a short to ground on a sense line often means a failed component on that net. Confirm with a second measurement before replacing anything.
PPCPUCORE_S0_SENSE_10.002–1.100R
AI: what PPCPUCORE_S0_SENSE_1 is and how to check it

PPCPUCORE_S0_SENSE_1 — from the name, a CPU core sense line in the S0 (running) state. The archive gives a diode reading of 0.002 and a resistance of 1.100R; no known-good voltage reading is listed.

  • Check with the board unpowered: diode mode from the net to ground, then resistance to ground, and compare with those two values.
  • With power applied, measure the voltage on the net; there is no known-good voltage here, so compare against a matching sense net or a known-good board.
  • A diode or resistance far below the known-good figure usually points to a short or a leaky part on that net; a far higher one suggests an open trace or missing part. These are guides only, and a likely cause is not a confirmed one.
PPCPUCORE_S0_SENSE_20.002––
AI: what PPCPUCORE_S0_SENSE_2 is and how to check it
  • What it is: A CPU core sense line, active in the S0 (running) state, judging by the name. The board data has no parts list, so which components sit on it isn't known.
  • Known-good reading: diode 0.002 (community value, a guide only). No known-good voltage or resistance reading here.
  • How to check: With the board unpowered, diode mode from the net to ground; then power up and measure the voltage on it.
  • If far from known-good: a much higher diode reading usually points to an open trace or missing connection; near-zero in both directions can mean a short to ground. Confirm with a second measurement before replacing anything.
PPCPUCORE_S0_SENSE_30.002––
AI: what PPCPUCORE_S0_SENSE_3 is and how to check it
  • What it is: From its name, PPCPUCORE_S0_SENSE_3 is a CPU core sense line in the S0 (running) state. The board data doesn't show which parts sit on it.
  • Known-good reading: Diode 0.002 to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the net to ground; then power up and measure its voltage.
  • If far off: A very low or shorted diode reading usually points to a short on that line or its load; confirm with a second measurement before replacing anything.
PPCPUCORE_S0_SENSE_40.002––
AI: what PPCPUCORE_S0_SENSE_4 is and how to check it

PPCPUCORE_S0_SENSE_4 is a CPU core sense line; the S0 in the name indicates the running state, and "sense" suggests it feeds back core voltage or current to the power controller (that part is general, not from board data). The only known-good reading here is a diode value of 0.002, with no condition recorded; there is no known-good voltage or resistance reading. Check it with the board unpowered in diode mode from the net to ground, then measure its voltage with power applied and compare against a known-good board. A diode reading far from 0.002 usually points to a short or a damaged component on that net, but one reading alone doesn't confirm a fault.

PPDDRVTT_S00.564––
AI: what PPDDRVTT_S0 is and how to check it
  • What it is: From the name, PPDDRVTT_S0 is a DDR termination-voltage rail (VTT) that is present in the S0 running state. It is a rail, not a signal.
  • Known-good reading: diode 0.564 to ground, from the readings archive. This is a community value and a guide only; there is no known-good voltage reading here.
  • How to check: power off and unplug, then measure diode mode from PPDDRVTT_S0 to ground and compare with 0.564. Then power up and measure the DC voltage on the rail.
  • If it's far off: a much lower diode reading usually points to a short or a leaky part on the rail; a much higher one to an open path or a missing connection. A single reading doesn't prove a part bad, so confirm with a second measurement before replacing anything.
PPFBVDDQ_S0_GPU0.063–62.400R
AI: what PPFBVDDQ_S0_GPU is and how to check it

PPFBVDDQ_S0_GPU — reference note

  • What it is: From the name, this is a GPU-related power rail (PP = power rail, FBVDDQ = memory/IO supply, GPU = graphics) that is up in the S0 running state. The archive doesn't say which parts sit on it.
  • Known-good readings (community, guide only): diode 0.063 and resistance 62.400R. No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground; then apply power and measure the rail voltage. Compare the diode reading with the archive value.
  • If far off: a much lower diode or resistance reading usually points to a shorted load or decoupling cap on the rail; a much higher one to an open feed or missing enable. Confirm with a second measurement before replacing anything.
PPGPUCORE_S0_SENSE_10.016––
AI: what PPGPUCORE_S0_SENSE_1 is and how to check it

PPGPUCORE_S0_SENSE_1 is a GPU core sense line, judged from its name; the S0 suffix indicates it is active in the running state. The only known-good figure here is a diode reading of 0.016 to ground, with no condition recorded and no known-good voltage reading. Check it unpowered in diode mode from the net to ground, then measure its voltage with the board powered in S0. A diode value far from 0.016 usually points to a short or a damaged sense path rather than a normal variation, but one reading alone doesn't confirm a bad part.

PPGPUCORE_S0_SENSE_20.016––
AI: what PPGPUCORE_S0_SENSE_2 is and how to check it
  • What it is: From the name, a GPU core sense line that is active in the S0 (running) state. The archive doesn't say which parts sit on the net.
  • Known-good reading: diode 0.016 to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the net to ground, then power up and measure the voltage on it.
  • If it's far off: a much higher diode reading suggests an open trace or missing connection; much lower suggests a short. Confirm with a second measurement before replacing anything.
PPGPUCORE_S0_SENSE_30.016–16.200R
AI: what PPGPUCORE_S0_SENSE_3 is and how to check it
  • What it is: The name suggests a GPU core sense line that is active in the S0 (running) state. That reading is from the name, not from a schematic.
  • Known-good readings: diode 0.016 and resistance 16.200R. These are community readings and only a guide.
  • How to check: With the board unpowered, measure diode mode from the net to ground, then measure resistance to ground. Then apply power and measure the voltage on the net.
  • If it's far off: A much higher diode or resistance reading usually points to an open trace or a missing connection. A much lower reading usually points to a short to ground. There is no known-good voltage reading for this net here, so compare against a matching net or a known-good board.
PPGPUCORE_S0_SENSE_40.016––
PPVAXG_S00.002–1.600R
AI: what PPVAXG_S0 is and how to check it
  • What it is: PPVAXG_S0 is a power rail; the S0 suffix means "running" state, from the name. The name suggests an AXG-related supply, but which parts sit on it isn't known here.
  • Known-good readings: diode 0.002 and resistance 1.600R, from community readings and a guide only. No known-good voltage is listed.
  • How to check: with the board unpowered, diode mode from the rail to ground, then resistance to ground; then power up and measure the rail voltage.
  • If far from known-good: a much higher diode or resistance reading usually points to an open feed or a missing part; a short to ground points to a failed component on the rail. Confirm with the voltage before replacing anything.
PPVCCSA_S00.007–6.600R
AI: what PPVCCSA_S0 is and how to check it

PPVCCSA_S0 — the suffix S0 means this rail is up in the running state (from the name); VCCSA is the system-agent supply, general knowledge, not from this board's data.

  • Known-good readings: diode 0.007 and resistance 6.600R. These are community archive values and only a guide; the data gives no voltage reading for this rail.
  • Check it: power off and unplug, then diode mode from the rail to ground. Next, with power applied, measure the voltage on the rail.
  • If a reading is far off: 0.007 diode and 6.6R are very low, so a much higher diode or resistance reading points to an open trace or missing feed, while a near-zero reading points to a short on the rail. Confirm with a second measurement before replacing anything.
PPVCORE_S0_CPU0.002–1.100R
AI: what PPVCORE_S0_CPU is and how to check it

PPVCORE_S0_CPU is the CPU core power rail; the S0 in the name indicates it is active in the running state. The archived readings for this rail are a diode reading of 0.002 and a resistance of 1.100R, which are community values and only a guide. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage on the rail with power applied. A reading far from these values usually points to a short or a failed component on the rail, but a single reading does not confirm a bad part. No known-good voltage reading is available here, so compare against a known-good board or a matching rail.

PPVCORE_S0_GPU0.016–16.200R
AI: what PPVCORE_S0_GPU is and how to check it

PPVCORE_S0_GPU — reference note

  • What it is: from the name, the GPU core power rail (VCORE) that is up in the S0 running state. The board data here is readings only, so the parts on this net aren't known.
  • Known-good readings: diode 0.016 and resistance 16.200R, both to ground with the board unpowered. These are community readings and a guide only; no known-good voltage is listed here.
  • How to check: power off and measure diode mode to ground, then resistance to ground, then power on and measure the rail voltage.
  • If far from known-good: a much lower diode or resistance reading usually points to a short or a failed component on the rail; a missing voltage with normal diode readings points more toward the rail not being enabled or its supply failing. Confirm with a second measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
4V5_REG_EN0.288––
4V5_REG_IN0.358––
9V_COMP_REF0.684––
12V_COMP_REF0.674––
ACDC_BURST_EN_L0.753––
AGND_BLC0.000––
AGND_FBVDDQ0.000––
AGND_VCCSAS00.001––
AP_CLKREQ_L0.570––
AP_CLKREQ_L_ISO0.480––
AP_CLKREQ_Q_L0.479––
AP_EVENT_L0.759––
AP_PWR_EN0.571––
AP_PWR_EN_ISO0.470––
AP_PWR_EN_R0.568––
AP_RESET_CONN_L0.480––
AP_WAKE_L1.817––
AUD_CODEC_MICBIAS0.553––
AUD_DMIC_CLK0.736––
AUD_DMIC_CLK_CONN0.744––
AUD_DMIC_SDA10.714––
AUD_DMIC_SDA1_CONN0.722––
AUD_GPIO_20.608––
AUD_GPIO_30.557––
AUD_HP_PORT_REFOL––
AUD_HS_MIC_NOL––
AUD_HS_MIC_P1.564––
AUD_HS_MIC_RC_NOL––
AUD_HS_MIC_RC_POL––
AUD_I2C_INT_L0.525––
AUD_IP_PERPH_DET_DB0.551––
AUD_IP_PERPH_DET_ROL––
AUD_IPHS_SWITCH_EN0.550––
AUD_IPHS_SWITCH_EN_PCH0.547––
AUD_IPHS_SWITCH_EN_PCH_R0.548––
AUD_J1_DET_RCOL––
AUD_J1_GND_ANALOG0.000––
AUD_J1_HP_OUTLOL––
AUD_J1_HP_OUTROL––
AUD_J1_HP_PORT_REFOL––
AUD_J1_MIC_BIAS0.571––
AUD_J1_MIC_NOL––
AUD_J1_MIC_P1.564––
AUD_J1_PP3V3_S00.339––
AUD_J1_TIPDET1_ROL––
AUD_J1_TIPDET2_ROL––
AUD_J1_TYPEDET_ROL––
AUD_LAMP_LINC_N0.715––
AUD_LAMP_LINC_P0.719––
AUD_LAMP_RINC_N0.721––
AUD_LAMP_RINC_P0.720––
AUD_LI_TIPDET0.550––
AUD_LO1_L_C_NOL––
AUD_LO1_L_C_POL––
AUD_LO1_L_N0.715––
AUD_LO1_L_P0.719––
AUD_LO1_R_C_NOL––
AUD_LO1_R_C_POL––
AUD_LO1_R_N0.717––
AUD_LO1_R_P0.716––
AUD_LO2_L_N0.720––
AUD_LO2_L_P0.721––
AUD_LO2_R_N0.716––
AUD_LO2_R_P0.720––
AUD_MIC_INL_N0.759––
AUD_MIC_INL_P0.759––
AUD_OUTJACK_INSERT0.615––
AUD_OUTJACK_INSERT_L0.590––
AUD_PORTA_DET_L0.605––
AUD_PORTB_DET_L1.156––
AUD_PORTC_DET_L0.603––
AUD_PORTD_DET_L1.114––
AUD_RAMP_AVDD0.550––
AUD_RAMP_BOOTLN0.597––
AUD_RAMP_BOOTRN0.595––
AUD_RAMP_BOOTRP0.597––
AUD_RAMP_GAIN0.613––
AUD_RAMP_LIN_N0.612––
AUD_RAMP_LIN_P0.612––
AUD_RAMP_LINC_N0.723––
AUD_RAMP_LINC_P0.723––
AUD_RAMP_OUTNL0.572––
AUD_RAMP_OUTNR0.566––
AUD_RAMP_OUTPL0.571––
AUD_RAMP_OUTPR0.569––
AUD_RAMP_RINC_N0.720––
AUD_RAMP_RINC_P0.716––
AUD_SDI_R0.481––
AUD_SENSE_A0.760––
AUD_SPDIF_CHIP0.710––
AUD_SPDIF_OUT0.737––
AUD_SPKR_RTWT_OUT_N0.569––
AUD_SPKR_RTWT_OUT_P0.571––
AUD_SPKR_RWFR_OUT_N0.569––
AUD_SPKR_RWFR_OUT_P0.566––
AUD_SPKR_VENDOR_ID_LOL––
AUD_SPKR_VENDOR_ID_ROL––
AUD_SPKRAMP_MAC_SHDN_L0.553––
AUD_SPKRAMP_WIN_SHDN_L0.557––
AUD_TIPDET_INVOL––
AUD_TIPDET1_ROL––
AUD_TIPDET2_ROL––
AUD_TYPEDET_ODOL––
AUD_TYPEDET_ROL––
BCOMP1OL––
BCOMP3OL––
BLC_BL0.608––
BLC_BL_GATE0.750––
BLC_BST0.749––
BLC_BST_R0.721––
BLC_BYPASS_GATE1.100––
BLC_DIM_MCU0.633––
BLC_EN_R0.671––
BLC_ENA0.658––
BLC_EXT_BOOT0.698––
BLC_GND_10.000––
BLC_GND_20.002––
BLC_GND_30.002––
BLC_GOOD0.684––
BLC_LED_N_10.547––
BLC_LED_N_20.555––
BLC_LED_N_30.551––
BLC_LED_P_10.778––
BLC_LED_P_20.778––
BLC_LED_P_30.780––
BLC_MCU_AOUT_R0.615––
BLC_MCU_B_SDA_CONNOL––
BLC_MCU_BV0.539––
BLC_MCU_BV_D0.737––
BLC_MCU_BV_R0.742––
BLC_MCU_PWM50.672––
BLC_MCU_PWM5_R0.675––
BLC_MCU_RESET_L0.597––
BLC_MCU_RESET_R_L0.597––
BLC_MCU_RTCK0.682––
BLC_MCU_RXD00.675––
BLC_MCU_TCK0.677––
BLC_MCU_TDI0.676––
BLC_MCU_TMS0.693––
BLC_MCU_TRST0.678––
BLC_MCU_TXD00.674––
BLC_MCU_UVLO0.683––
BLC_MCU_XTAL_IN0.635––
BLC_MCU_XTAL_OUT0.634––
BLC_MCU_XTAL_OUT_R0.636––
BLC_ON2.180––
BLC_ON_DRAIN1.235––
BLC_P_ON0.615––
BLC_P_ON_BYPASS0.708––
BLC_P_ON_D_R2.119––
BLC_P_ON_DRAIN0.558––
BLC_P_ON_GATE0.759––
BLC_P_ON_R0.700––
BLC_P3V3_REF0.289––
BLC_P3V3A0.289––
BLC_P3V3S0.293––
BLC_PWM_10.545––
BLC_PWM_1_R0.671––
BLC_PWM_20.560––
BLC_PWM_2_R0.674––
BLC_PWM_30.606––
BLC_PWM_3_R0.670––
BLC_SNUB_1OL––
BLC_SNUB_2OL––
BLC_SNUB_3OL––
BLC_UVLO0.743––
BLC_VIN_SNS0.733––
BLC_VIN20.490––
BLC_VIN2_GATEOL––
BLC_VIN2_SRC0.621––
BLC_VINP_GATEOL––
BLC_VOUT10.776––
BLC_VOUT20.773––
BLC_VOUT30.778––
BLC_VSYNC1.613––
BOOST_BPOL––
BOOST_BYPASS0.999––
BOOST_BYPASS_GATEOL––
BOOST_COMPOL––
BOOST_EN_GATE0.702––
BOOST_EN_L0.606––
BOOST_FBOL––
BOOST_FET_DRAIN0.527––
BOOST_GDRVOL––
BOOST_GDRV_ROL––
BOOST_ISNSOL––
BOOST_ISNS_ROL––
BOOST_RCOL––
BOOST_SSOL––
BOOST_VDDOL––
BT_PWR_ENOL––
BT_PWR_RST_L_QOL––
BURSTMODE_ENOL––
BURSTMODE_EN_L1.000––
CAM_AGND0.000––
CAM_EXT_BOOT0.535––
CAM_P1V2_RST_HOLDOFF1.379––
CAM_P1V2_RST_HOLDOFF_L1.380––
CAM_PROC_RESET_L0.535––
CAM_SF_CLK_R0.555––
CAM_SF_CS_L0.558––
CAM_SF_WP_L0.556––
CAM_XTAL_IN0.488––
CAM_XTAL_OUT_R0.604––
CPU_PROCHOT_L0.065––
CPU_RESET_L0.091––
CPU_THRMTRIP_3V30.748––
CPU_THRMTRIP_L0.320––
CPU_THRMTRIP_R_LOL––
CS4206_DMIC_SCL0.709––
CS4206_FLYC0.433––
CS4206_FLYP0.631––
CS4206_FN1.936––
CS4206_FP0.450––
CS4206_HPREF0.024––
CS4206_VCOM0.609––
CS4206_VREF_ADC0.766––
DP_INT_SPDIF_AUDIO0.766––
DP_INTPNL_AUX_N0.741––
DP_INTPNL_HPD0.550––
DP_INTPNL_ML_C_N<0>0.466––
DP_INTPNL_ML_C_N<1>0.476––
DP_INTPNL_ML_C_N<2>0.464––
DP_INTPNL_ML_C_N<3>0.465––
DP_INTPNL_ML_C_P<0>0.465––
DP_INTPNL_ML_C_P<1>0.476––
DP_INTPNL_ML_C_P<2>0.463––
DP_INTPNL_ML_C_P<3>0.462––
DP_INTPNL_ML_N<0>OL––
DP_INTPNL_ML_N<1>OL––
DP_INTPNL_ML_N<2>OL––
DP_INTPNL_ML_N<3>OL––
DP_INTPNL_ML_P<0>OL––
DP_INTPNL_ML_P<1>OL––
DP_INTPNL_ML_P<2>OL––
DP_INTPNL_ML_P<3>OL––
DP_TBT_SEL0.550––
DP_TBTPA_AUXCH_N0.737––
DP_TBTPA_AUXCH_P0.699––
DP_TBTPA_ML_N<1>0.690––
DP_TBTPA_ML_P<1>0.705––
DP_TBTPB_DDC_DATA0.561––
DP_TBTSNK0_AUXCH_C_N0.651––
DP_TBTSNK1_AUXCH_C_P0.652––
DP_TBTSNK1_DDC_CLK0.531––
DP_TBTSRC_AUXCH_N0.560––
ENET_ACT0.765––
ENET_CLKREQ_L0.567––
ENET_CLKREQ_L_Q0.763––
ENET_CS_L0.714––
ENET_MISO0.624––
ENET_MOSI0.735––
ENET_PWR_EN_L_ROL––
ENET_RESET_L0.472––
ENET_SCLK0.732––
ENET_SR_DISABLE0.573––
ENET_SR_LX0.297––
ENET_TRAFFICLED_L0.765––
ENET_VMAIN_PRSNT0.598––
ENET_WAKE_L0.582––
ENETCONN_MCT0OL––
ENETCONN_MCT1OL––
ENETCONN_MCT2OL––
ENETCONN_MCT3OL––
ENETCONN_MDI_N<0>0.377––
ENETCONN_MDI_N<1>0.378––
ENETCONN_MDI_N<2>0.377––
ENETCONN_MDI_N<3>0.378––
ENETCONN_MDI_P<0>0.377––
ENETCONN_MDI_P<1>0.378––
ENETCONN_MDI_P<2>0.377––
ENETCONN_MDI_P<3>0.378––
ENETCONN_MDI_T_N<0>OL––
ENETCONN_MDI_T_N<1>OL––
ENETCONN_MDI_T_N<2>OL––
ENETCONN_MDI_T_N<3>OL––
ENETCONN_MDI_T_P<0>OL––
ENETCONN_MDI_T_P<1>OL––
ENETCONN_MDI_T_P<2>OL––
ENETCONN_MDI_T_P<3>OL––
ENETCONN_TCT0.378––
FAN_0_PWM_FET1.111––
FAN_0_PWM_FILT1.111––
FAN_0_TACH_FETOL––
FAN_0_TACH_FILTOL––
FET_HDD_SLGSW0.536––
FLAG_V0.662––
FLAG_V_L0.559––
GND_AUDIO_CODEC0.001––
GND_AUDIO_HPAMP0.000––
GPU_GOOD0.565––
GPU_PSI_L0.544––
HDA_BIT_CLK0.503––
HDA_BIT_CLK_R0.469––
HDA_RST_L0.494––
HDA_SDIN00.461––
HDA_SDOUT0.497––
HDA_SYNC_R0.435––
HDD_12V_S0_GATE0.682––
HDD_OOB_1V00_REF0.710––
HDD_PWR_EN0.514––
HDD_PWR_EN_L0.611––
HDD_PWR_EN_R0.511––
HDD5V_RAMP_CAP0.649––
HPOUT_JFET_GOL––
HS_HDET1.996––
HS_MIC_BIAS0.571––
HS_RX_BP0.594––
HS_SW_DET0.563––
I2C_CAMSENSOR_SCL0.530––
I2C_CAMSENSOR_SDA0.531––
I2C_TCON_MAS_SCL0.636––
I2C_TCON_MAS_SDA0.638––
IS1_BLC0.540––
IS1_BLC_F0.554––
IS2_BLC0.553––
IS2_BLC_F0.553––
IS3_BLC0.553––
IS3_BLC_F0.552––
ISNS_CPUAXG_FB0.702––
ISNS_CPUCORE_FB0.700––
ISNS_GPUCORE_FB0.695––
ISNS_GPUCORE_N0.677––
ISNS_GPUCORE_P0.683––
ISNS_P1V05S0_PCH_R0.726––
ISNS_P3V3S4_AP_ROL––
ISNS_P5VS0_HDD_R0.363––
ISNS_P12VG3H_R0.722––
ISNS_P12VS0_CPU_VCCSA_R0.714––
ISNS_P12VS0_FBVDDQ_R0.719––
ISNS_P12VS0_HDD_R0.717––
ISNSA_P1V5S0_CPU_MEM_N0.130––
ISNSA_P1V5S0_CPU_MEM_P0.130––
ISNSA_P1V05S0_PCH_N0.045––
ISNSA_P1V05S0_PCH_P0.045––
ISNSA_P3V3S0_SSD_N0.289––
ISNSA_P3V3S0_SSD_P0.289––
ISNSA_P3V3S4_AP_N0.340––
ISNSA_P3V3S4_AP_P0.340––
ISNSA_P5VS0_HDD_N0.363––
ISNSA_P5VS0_HDD_P0.363––
ISNSA_P12VG3H_N0.568––
ISNSA_P12VG3H_P0.568––
ISNSA_P12VS0_CPU_P1V05_N0.444––
ISNSA_P12VS0_CPU_P1V05_P0.444––
ISNSA_P12VS0_CPU_VCCSA_N0.444––
ISNSA_P12VS0_CPU_VCCSA_P0.444––
ISNSA_P12VS0_FBVDDQ_N0.444––
ISNSA_P12VS0_FBVDDQ_P0.444––
ISNSA_P12VS0_HDD_N0.444––
ISNSA_P12VS0_HDD_P0.444––
ISNSA_P12VS0_P1V05_N0.444––
ISNSA_P12VS0_P1V05_P0.444––
ISNSA_PVDDQS3_DDR_N0.343––
ISNSA_PVDDQS3_DDR_P0.343––
JTAG_TBT_TCK_R0.548––
JTAG_TBT_TDO_ISOL0.660––
LED_DRIVER_COMP10.691––
LED_DRIVER_COMP20.694––
LED_DRIVER_COMP30.687––
LED_DRIVER_CS10.220––
LED_DRIVER_CS20.220––
LED_DRIVER_CS30.220––
LED_DRIVER_EN0.740––
LED_DRIVER_EN_LOL––
LED_DRIVER_EN_L_R0.556––
LED_DRIVER_FDBK_R_10.003––
LED_DRIVER_FDBK_R_20.003––
LED_DRIVER_FDBK_R_30.003––
LED_DRIVER_FDBK10.692––
LED_DRIVER_FDBK20.691––
LED_DRIVER_FDBK30.692––
LED_DRIVER_FLT10.701––
LED_DRIVER_FLT20.701––
LED_DRIVER_FLT30.701––
LED_DRIVER_GATE10.645––
LED_DRIVER_GATE1_R0.655––
LED_DRIVER_GATE20.646––
LED_DRIVER_GATE2_R0.646––
LED_DRIVER_GATE30.645––
LED_DRIVER_GATE3_R0.645––
LED_DRIVER_OVP10.696––
LED_DRIVER_OVP1_OUT0.697––
LED_DRIVER_OVP20.692––
LED_DRIVER_OVP2_OUT0.691––
LED_DRIVER_OVP2P0.652––
LED_DRIVER_OVP30.695––
LED_DRIVER_OVP3_OUT0.695––
LED_DRIVER_REF10.623––
LED_DRIVER_REF20.623––
LED_DRIVER_REF30.617––
LED_DRVR_CLK0.731––
LED_DRVR_CS_C10.221––
LED_DRVR_CS_C20.221––
LED_DRVR_CS_C30.221––
LED_DRVR_CS_RC_10.002––
LED_DRVR_CS_RC_20.002––
LED_DRVR_CS_RC_30.002––
LED_DRVR_DRAIN_10.527––
LED_DRVR_DRAIN_20.527––
LED_DRVR_DRAIN_30.527––
LED_FLT_R_10.726––
LED_FLT_R_20.722––
LED_FLT_R_30.720––
LFRAME_L0.555––
LPC_AD<1>0.590––
LPC_CLK33M_LPCPLUS0.610––
LPC_FRAME_L0.584––
LPC_R_AD<3>0.555––
LPCPLUS_GPIO0.586––
MAX9119_NEG0.705––
MAX9119_OUT0.710––
MAX9119_POS0.703––
MAX97220_BIAS2.035––
MAX97220_C1N0.871––
MAX97220_C1P0.538––
MAX97220_OUTLOL––
MAX97220_OUTL_ZOBEL0.035–35.000R
MAX97220_OUTROL––
MAX97220_OUTR_ZOBEL0.035–0.350R
MAX97220_PVSS1.477––
MAX97220_SHDN_L0.608––
MOJO_RX_L0.740––
MOJO_TX_L0.738––
OCA_FET_DRAIN0.614––
OVP_OREF0.680––
OVP_OUT1_R0.746––
OVP_OUT20.742––
OVP_OUT2_R0.742––
OVP_OUT30.742––
OVP_OUT3_R0.742––
P1V05_AGND0.000––
P3V3AP_VMON0.478––
P3V42G3H_BOOST0.630––
P3V42G3H_FB0.726––
P3V42G3H_SHDN_L0.730––
P3V42G3H_SW0.326––
PCH_BLC_EXT_BOOT0.588––
PCH_CAM_EXT_BOOT_L0.578––
PCH_CAM_EXT_BOOT_R_L0.612––
PCH_CAM_RESET_R0.618––
PCH_CLK100M_SATAN0.762––
PCH_CLK100M_SATAP0.769––
PCH_DSWVRMEN0.763––
PCH_GPIO320.579––
PCH_RCIN_L0.755––
PCH_SMBALERT_L0.596––
PCIE_AP_D2R_N0.377––
PCIE_AP_D2R_P0.375––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_N0.391––
PCIE_CLK100M_AP_P0.391––
PCIE_CLKREQ5_GPIO44_L0.556––
PCIE_ENET_D2R_C_N0.485––
PCIE_ENET_D2R_C_P0.486––
PCIE_ENET_D2R_N0.390––
PCIE_ENET_D2R_P0.383––
PCIE_WAKE_L0.524––
PGOOD_12V_S0_G10.676––
PM_CLKRUN_LOL––
PM_DSW_PWRGD0.711––
PM_EN_FET_P3V3_S40.458––
PM_EN_FET_P12V_S00.598––
PM_EN_FET_P12V_S0_R0.560––
PM_EN_REG_CPUCORE_S00.535––
PM_EN_REG_GPUCORE_S0_R0.653––
PM_EN_REG_P1V05_S00.509––
PM_EN_REG_P3V3_S50.528––
PM_PCH_APWROK0.694––
PM_PCH_PWROK_APWROK0.695––
PM_PCH_SYS_PWROK0.628––
PM_PGOOD_REG_FBVDDQ_S00.540––
PM_PGOOD_REG_GPUCORE_S00.527––
PM_PGOOD_REG_P3V3_S50.551––
PM_PGOOD_REG_P5V_S40.453––
PM_PGOOD_REG_VCCSA_S00.535––
PM_RSMRST_PCH_L0.544––
PM_RSMRST_PCH_L_R0.546––
PM_SLP_S5_L0.590––
PM_SYSRST_L0.586––
PM_THRMTRIP_L0.062––
PP1V2_ENET_INTREG0.296––
PP1V2_G3H_SMC_VDDC0.528––
PP1V2_S4_CAMERA0.379––
PP1V2_S4_ENET_PHY_AVDDL0.296––
PP1V2_S4_ENET_PHY_GPHYPLL0.296––
PP1V2_S4_ENET_PHY_PCIEPLL0.296––
PP1V05_S00.045–44.000R
PP1V5_S00.130––
PP1V05_S0_CPU0.011––
PP1V5_S0_CPU_MEM0.130–128.000R
PP1V05_S0_PCH0.045––
PP1V05_TBTCIO0.166––
PP1V05_TBTLC0.130––
PP1V8_S00.211––
PP1V8_S4_CAMERA0.438––
PP1V8_S4_CAMERA_F0.438––
PP3V3_DMIC_CONN0.289––
PP3V3_G30.568––
PP3V3_G3H_AVREF_SMC0.603––
PP3V3_G3H_BT_FET0.507––
PP3V3_G3H_BT_FLT0.507––
PP3V3_G3H_SMC_USBMUX_R0.318––
PP3V3_G3H_SMC_VDDA0.326––
PP3V3_GPU_IFPX_PLLVDD0.289––
PP3V3_S00.289––
PP3V3_S0_BLC_R0.289––
PP3V3_S0_SSD0.289––
PP3V3_S0_SSD_FLT0.289––
PP3V3_S0_SW_SD_PWR0.558––
PP3V3_S40.340––
PP3V3_S4_ALS_F0.340––
PP3V3_S4_AP0.340––
PP3V3_S4_AP_FET0.508––
PP3V3_S4_AP_FLT0.508––
PP3V3_S4_CAMFILT0.343––
PP3V3_S4_ENET0.365––
PP3V3_S4_ENET_FET_AVDDH0.365––
PP3V3_S4_ENET_FET_BIASVDDH0.365––
PP3V3_S4_ENET_FET_XTALVDDH0.365––
PP3V3_S50.150––
PP3V3_S5_XDP_R0.101––
PP3V3_TBTLC0.417––
PP3V3R1V8_ENET_LR_OUT_REG0.560––
PP3V3RHV_SW_TBTAPWR0.569––
PP3V3RHV_SW_TBTBPWR0.569––
PP3V42_G3H0.326––
PP3V42_G3H_SMC_SPVSR0.371––
PP4V5_AUDIO_ANALOG0.500––
PP5V_AUDIO_HPAMP0.358––
PP5V_S00.363––
PP5V_S0_BLC_R0.366––
PP5V_S0_GPU_VCORE_VCC0.361––
PP5V_S0_HDD0.363––
PP5V_S0_HDD_FET0.600––
PP5V_S0_PCH_V5REF0.366––
PP5V_S40.157––
PP5V_S4_CAMERA_F0.157––
PP5V_S4_EXTA0.526––
PP5V_S4_EXTA_F0.526––
PP5V_S4_EXTB0.527––
PP5V_S4_EXTB_F0.526––
PP5V_S4_EXTC0.529––
PP5V_S4_EXTC_F0.529––
PP5V_S4_EXTD0.528––
PP5V_S4_EXTD_F0.528––
PP5V_S50.400––
PP5V_S5_PCH_V5REFSUS0.392––
PP8V_BLC0.676––
PP12V_ACDC0.568––
PP12V_G3H0.568––
PP12V_G3H_P3V420.570––
PP12V_LCD0.444––
PP12V_LCD_EXT0.444––
PP12V_S00.444––
PP12V_S0_BLC0.545––
PP12V_S0_BLC_F0.545––
PP12V_S0_BLC_VIN20.510––
PP12V_S0_BLC_VINP0.527––
PP12V_S0_CPU_P1V050.444––
PP12V_S0_CPUCORE_FLT0.444––
PP12V_S0_FAN_0_FILT0.444––
PP12V_S0_FBVDDQ0.444––
PP12V_S0_GPUCORE_FLT0.444––
PP12V_S0_HDD0.444––
PP12V_S0_HDD_FET0.670––
PP12V_S0_P1V050.444––
PP12V_S0_VCCSA0.444––
PP12V_S50.527––
PPCPUAXG_S0_SENSE0.002––
PPCPUCORE_S0_SENSE_10.002–1.100R
PPCPUCORE_S0_SENSE_20.002––
PPCPUCORE_S0_SENSE_30.002––
PPCPUCORE_S0_SENSE_40.002––
PPDDRVTT_S00.564––
PPFBVDDQ_S0_GPU0.063–62.400R
PPGPUCORE_S0_SENSE_10.016––
PPGPUCORE_S0_SENSE_20.016––
PPGPUCORE_S0_SENSE_30.016–16.200R
PPGPUCORE_S0_SENSE_40.016––
PPHV_SW_TBTAPWR0.569––
PPHV_SW_TBTBPWR0.569––
PPVAXG_S00.002–1.600R
PPVBATT_G3_RTCOL––
PPVBATT_G3_RTC_ROL––
PPVCCSA_S00.007–6.600R
PPVCORE_S0_CPU0.002–1.100R
PPVCORE_S0_GPU0.016–16.200R
PPVDDQ_S30.335––
PPVDDQ_S3_DDR0.343––
PPVOUT_G3_PCH_DCPRTC0.630––
PRE_REG_OUT0.527––
PRE_REG_OUT_ROL––
Q6170_N_GOL––
Q6170_N_SOL––
Q6170_P_GOL––
Q6170_P_SOL––
Q6171_N_GOL––
Q6171_N_SOL––
Q6171_P_GOL––
Q6171_P_SOL––
REG_BOOT_FBVDDQ0.567––
REG_BOOT_FBVDDQ_RC0.567––
REG_BOOT_GPUCORE_10.590––
REG_BOOT_GPUCORE_40.517––
REG_BOOT_GPUCORE_4_RC0.517––
REG_BOOT_P3V3S50.608––
REG_BOOT_P3V3S5_RC0.608––
REG_BOOT_P5VS40.610––
REG_BOOT_P5VS4_RC0.610––
REG_BOOT_VCCSAS00.536––
REG_BOOT_VCCSAS0_RC0.537––
REG_CPU_PHASE_P1V05S00.011––
REG_FBVDDQ_FB0.529––
REG_FBVDDQ_FSEL0.544––
REG_FBVDDQ_OCSET0.535––
REG_FBVDDQ_RTN0.532––
REG_FBVDDQ_SET00.544––
REG_FBVDDQ_SET1_R0.542––
REG_FBVDDQ_SREF0.541––
REG_FBVDDQ_VO0.534––
REG_GPUCORE_VID20.503––
REG_GPUCORE_VID40.621––
REG_GPUCORE_VID60.635––
REG_ISEN_GCORE_1_N0.016––
REG_ISEN_GCORE_1_P0.016––
REG_ISEN_GCORE_2_N0.016––
REG_ISEN_GCORE_2_P0.016––
REG_ISEN_GCORE_3_N0.016–16.200R
REG_ISEN_GCORE_3_P0.016–16.200R
REG_ISEN_GCORE_4_N0.016––
REG_ISEN_GCORE_4_P0.016––
REG_ISENAXG_N0.002––
REG_ISENAXG_P0.002––
REG_ISENCORE_1_N0.002–1.100R
REG_ISENCORE_1_P0.002–1.100R
REG_ISENCORE_2_N0.002––
REG_ISENCORE_2_P0.002––
REG_ISENCORE_3_N0.002––
REG_ISENCORE_3_P0.002––
REG_ISENCORE_4_N0.002––
REG_ISENCORE_4_P0.002––
REG_LGATE_FBVDDQ0.451––
REG_LGATE_P1V05S00.447––
REG_LGATE_P3V3S50.464––
REG_LGATE_P5VS40.459––
REG_LGATE_VCCSAS00.447––
REG_LGATE_VDDQS30.466––
REG_LVCC_UB5300.447––
REG_LVCC_UB6500.456––
REG_P3V3S5_FB0.550––
REG_P3V3S5_FSET0.556––
REG_P3V3S5_ISEN0.551––
REG_P3V3S5_OCSET0.555––
REG_P3V3S5_VOUT0.146––
REG_P3V3S5_VOUT_R1.131––
REG_P5VS4_FB0.550––
REG_P5VS4_FSET0.556––
REG_P5VS4_ISEN0.551––
REG_P5VS4_OCSET0.553––
REG_P5VS4_VOUT0.157––
REG_P5VS4_VOUT_R1.140––
REG_PHASE_CPUAXG0.002––
REG_PHASE_CPUCORE_20.002––
REG_PHASE_CPUCORE_30.002––
REG_PHASE_CPUCORE_40.002––
REG_PHASE_FBVDDQ0.063––
REG_PHASE_GPUCORE_10.016––
REG_PHASE_GPUCORE_20.016––
REG_PHASE_GPUCORE_30.016––
REG_PHASE_GPUCORE_40.016––
REG_PHASE_P1V05S00.038––
REG_PHASE_P1V05S0_L0.045––
REG_PHASE_P1V8S00.211––
REG_PHASE_P3V3S50.151––
REG_PHASE_P5VS40.157––
REG_PHASE_VCCSAS00.007––
REG_PHASE_VDDQS30.342––
REG_PHASE_VDDQS3_L0.343––
REG_PVCC_U75000.361––
REG_PVCC_UB7500.362––
REG_PWM_GPUCORE_10.677––
REG_PWM_GPUCORE_30.681––
REG_SNUBBER_FBVDDQOL––
REG_SNUBBER_GPUCORE_4OL––
REG_SNUBBER_P3V3S5OL––
REG_SNUBBER_P5VS4OL––
REG_SNUBBER_VDDQS3OL––
REG_U7600_FCCM0.560––
REG_U7600_FCCM_ROL––
REG_UGATE_FBVDDQ0.535––
REG_UGATE_GPUCORE_40.621––
REG_UGATE_P1V05S00.532––
REG_UGATE_P5VS40.599––
REG_UGATE_VCCSAS00.570––
REG_UGATE_VDDQS30.830––
REG_VCC_U75000.367––
REG_VCC_UB7500.370––
REG_VCC1_U76000.521––
REG_VCC2_U76000.408––
REG_VCCSAS0_FB0.512––
REG_VCCSAS0_FSEL0.002––
REG_VDDQS3_REFIN0.700––
REG_VDDQS3_VDDQSNS0.332––
REG_VDDQS3_VREF0.648––
REG_VIN_U76000.528––
RTC_RESET_L0.750––
RTC_RESET_L_R0.616––
SATA_HDD_D2R_C_NOL––
SATA_HDD_D2R_C_POL––
SATA_HDD_R2D_C_N0.350––
SATA_HDD_R2D_C_P0.350––
SATA_HDD_R2D_NOL––
SATA_HDD_R2D_POL––
SATA_SSD_D2R_N0.381––
SATA_SSD_D2R_P0.378––
SATA_SSD_R2D_N0.347––
SATA_SSD_R2D_P0.348––
SATALED_R_LOL––
SDCONN_CLK0.582––
SDCONN_CLK_R0.582––
SDCONN_CMD_R0.576––
SDCONN_DATA_R<0>0.576––
SDCONN_DATA_R<1>0.576––
SDCONN_DATA_R<2>0.577––
SDCONN_DATA_R<3>0.582––
SDCONN_DATA_R<4>0.788––
SDCONN_DATA_R<5>0.787––
SDCONN_DATA_R<6>0.788––
SDCONN_DATA_R<7>0.788––
SDCONN_DATA<0>0.577––
SDCONN_DATA<1>0.576––
SDCONN_DATA<4>0.790––
SDCONN_DATA<5>0.795––
SDCONN_DATA<6>0.789––
SDCONN_DATA<7>0.788––
SDCONN_DETECT0.475––
SDCONN_STATE_CHANGE0.464––
SDCONN_WP0.757––
SLG_ENET_RESET_L0.433––
SMB_ALS_F_SCL0.777––
SMB_ALS_F_SDA0.755––
SMB_ENET_SDA0.735––
SMB_PCH_BLC_SDA0.511––
SMB_TCON_BLC_SCL0.636––
SMB_TCON_BLC_SDA0.633––
SMBUS_PCH_CLK0.504––
SMBUS_PCH_CLK_ROL––
SMBUS_PCH_DATA0.512––
SMBUS_SMC_1_S0_SCL0.720––
SMBUS_SMC_1_S0_SDA0.721––
SMBUS_SMC_2_S4_SCL0.755––
SMBUS_SMC_2_S4_SDA0.750––
SMBUS_SMC_3_SCL0.753––
SMBUS_SMC_3_SDA0.753––
SMC_ASSERT_RTCRST0.757––
SMC_BLC_FAULT0.761––
SMC_CPU_PECI0.331––
SMC_DELAYED_PWRGD0.686––
SMC_EXTAL0.780––
SMC_FAN_0_CTL0.760––
SMC_FAN_0_TACH0.763––
SMC_GFX_OVERTEMP0.756––
SMC_GFX_THROTTLE_L0.544––
SMC_MANUAL_RST_L0.674––
SMC_OOB1_RX_CN0.608––
SMC_OOB1_RX_FILT0.608––
SMC_OOB1_RX_L0.664––
SMC_OOB1_RX_R0.711––
SMC_OOB2_RX_L0.753––
SMC_OOB2_TX_L0.753––
SMC_PECI_L0.744––
SMC_PECI_L_R0.745––
SMC_PM_G2_EN0.582––
SMC_PME_S4_WAKE_L0.596––
SMC_PROCHOT0.753––
SMC_RESET_L0.552––
SMC_ROMBOOT1.738––
SMC_RX_L0.763––
SMC_S4_WAKESRC_EN0.760––
SMC_S5_PWRGD_VIN0.750––
SMC_TCK0.758––
SMC_TDI0.760––
SMC_TDO0.760––
SMC_THRMTRIP0.757––
SMC_TMS0.758––
SMC_TX_L0.761––
SMC_WAKE_SCI_L0.562––
SMC_XTAL0.768––
SMC_XTAL_R0.800––
SMCISNS_GPUCORE0.746––
SMCISNS_P1V5S0_CPU_MEM0.756––
SMCISNS_P1V05S0_PCH0.747––
SMCISNS_P3V3S0_SSD0.759––
SMCISNS_P12VG3H0.750––
SMCISNS_P12VS0_CPU_VCCSA0.758––
SMCISNS_P12VS0_P1V050.756––
SMCISNS_PVDDQS3_DDR0.758––
SMCVSNS_CPUCORE0.751––
SMCVSNS_P3V3S00.745––
SMCVSNS_P5VS0_HDD0.751––
SMCVSNS_P12VG3H0.740––
SMIA_CLK_N0.481––
SMIA_CLK_P0.487––
SMIA_DATA_N0.470––
SMIA_DATA_P0.475––
SML_PCH_0_CLK0.584––
SML_PCH_0_DATA0.588––
SNS_FBVDDQ_XW_N0.001––
SNS_FBVDDQ_XW_P0.064––
SNS_VCCSAS0_XW_P0.008––
SPI_ALT_CLK0.621––
SPI_ALT_CS_L0.612––
SPI_ALT_MISO0.544––
SPI_ALT_MOSI0.593––
SPI_CLK_R0.555––
SPI_CS0_L0.563––
SPI_DESCRIPTOR_OVERRIDE_L0.758––
SPI_DESCRIPTOR_OVERRIDE_R0.796––
SPI_MISO0.520––
SPI_MLB_CLK0.618––
SPI_MLB_CS_L0.602––
SPI_MLB_MISO0.527––
SPI_MLB_MOSI0.538––
SPI_MOSI_R0.525––
SPI_SMC_CLK0.626––
SPI_SMC_MISO0.547––
SPI_SMC_MOSI0.548––
SPI_WP_L0.644––
SPKR_MATCH_DRV0.743––
SPKR_MATCH_DRV_R0.743––
STRCLK_R10.670––
SYS_PWROK_R0.552––
TBT_A_HPD0.843––
TBT_A_LSRX_UNBUF0.692––
TBT_A_LSTX0.580––
TBT_B_CIO_SEL0.571––
TBT_B_HPD0.844––
TBT_B_LSTX0.586––
TBT_CLKREQ_L0.473––
TBT_DDC_XBAR_EN_L0.534––
TBT_EN_LC_ISOL0.466––
TBT_EN_LC_PWR0.560––
TBT_EN_LC_RC1V050.466––
TBT_MONOBSN0.194––
TBT_PCH_CLKREQ_L0.559––
TBT_PWR_ON_POC_RST_L0.556––
TBT_RBIAS0.799––
TBT_SPI_CLK0.575––
TBT_SPI_CS_L0.672––
TBT_TEST_PWR_GOOD0.004––
TBTACONN_20_RC0.580––
TBTAPWRSW_ISET_S00.476––
TBTAPWRSW_ISET_S0_ROL––
TBTAPWRSW_ISET_S30.476––
TBTAPWRSW_ISET_S3_ROL––
TBTAPWRSW_ISET_V3P30.477––
TBTBCONN_20_RC0.581––
TBTBPWRSW_ISET_S00.477––
TBTBPWRSW_ISET_S0_ROL––
TBTBPWRSW_ISET_S30.476––
TBTBPWRSW_ISET_S3_ROL––
TBTBPWRSW_ISET_V3P30.479––
TBTROM_WP_L0.739––
TP_PCH_GPIO6_TACH20.682––
TP_PCH_STRP_ESI_L0.555––
TP_SMC_MD1OL––
TP_SMC_TRST_LOL––
TP_TBT_MONDC00.370––
TP_TBT_MONDC10.669––
TP_TBT_THERM_DP0.736––
TP_TBT_XTAL25OUT0.284––
TSNS_2_2_P0.769––
TSNS_2_3_N0.765––
TSNS_2_3_P0.775––
TSNS_2_6_N0.778––
U9800_PIN200.001––
U9800_SC0.740––
USB_ACT_DET0.795––
USB_BT_MUX_P0.793––
USB_BT_N0.734––
USB_DEBUGPRT_EN_L0.744––
USB_EXTA_OC_L0.485––
USB_EXTAB_ILIM0.520––
USB_EXTAB_ILIM_ROL––
USB_EXTB_OC_L0.484––
USB_EXTB_SEL_XHCI0.603––
USB_EXTC_OC_L0.487––
USB_EXTD_SEL_XHCI0.605––
USB_HUB_XTAL10.787––
USB_HUB_XTAL2_R0.744––
USB_PCH_3_P0.539––
USB_PCH_10_N0.545––
USB2_EXTA_MUXED_F_N0.791––
USB2_EXTA_MUXED_F_P0.791––
USB2_EXTA_MUXED_N0.791––
USB2_EXTA_MUXED_P0.791––
USB2_EXTB_MUXED_F_N0.606––
USB2_EXTB_MUXED_F_P0.596––
USB2_EXTB_MUXED_N0.606––
USB2_EXTB_MUXED_P0.596––
USB2_EXTC_F_N0.558––
USB2_EXTC_F_P0.558––
USB2_EXTD_MUXED_F_N0.606––
USB2_EXTD_MUXED_F_P0.598––
USB3_EXTA_RX_N0.379––
USB3_EXTA_RX_P0.378––
USB3_EXTA_TX_C_NOL––
USB3_EXTA_TX_C_POL––
USB3_EXTA_TX_F_NOL––
USB3_EXTA_TX_F_POL––
USB3_EXTB_RX_N0.378––
USB3_EXTB_RX_P0.375––
USB3_EXTB_TX_C_NOL––
USB3_EXTB_TX_C_POL––
USB3_EXTB_TX_F_NOL––
USB3_EXTB_TX_F_POL––
USB3_EXTB_TX_N0.355––
USB3_EXTC_RX_N0.382––
USB3_EXTC_RX_P0.376––
USB3_EXTC_TX_C_NOL––
USB3_EXTC_TX_C_POL––
USB3_EXTC_TX_F_NOL––
USB3_EXTC_TX_F_POL––
USB3_EXTC_TX_P0.355––
USB3_EXTD_RX_N0.373––
USB3_EXTD_RX_P0.377––
USB3_EXTD_TX_C_NOL––
USB3_EXTD_TX_C_POL––
USB3_EXTD_TX_F_NOL––
USB3_EXTD_TX_F_POL––
USB3_EXTD_TX_P0.355––
UVP_IN_10.745––
UVP_IN_1_REF0.748––
UVP_IN_20.747––
UVP_IN_30.737––
UVP_IN_40.742––
UVP_REF0.706––
VBIAS_DAC0.747––
VIDEO_ON0.814––
VR_GPU_COMP_RCOL––
VR_GPU_IMON_R0.732––
VR_GPU_ISNS2_R_N0.710––
VR_GPU_ISNS3_RR_20.014––
VR_GPU_PWM1_R0.678––
VR_GPU_PWM2_R0.675––
VR_GPU_PWM3_R0.680––
VR_GPU_VSEN0.015––
XDP_CPU_PLTRST_L1.562––
XDP_DA0_USB_EXTA_OC_L0.523––
XDP_DA1_USB_EXTB_OC_L0.517––
XDP_DA2_USB_EXTC_OC_L0.530––
XDP_DA3_USB_EXTD_OC_L0.518––
XDP_DB0_USB_EXTB_OC_EHCI_L0.588––
XDP_DB1_USB_EXTD_OC_EHCI_L0.588––
XDP_DB2_AP_PWR_EN0.596––
XDP_DB3_SDCONN_STATE_CHANGE0.491––
XDP_DC3_SATARDRVR_EN0.586––
XDP_DD0_DP_TBT_SEL0.580––
XDP_DD2_AUD_IPHS_SWITCH_EN_PCH0.580––
XDP_PCH_PWRBTN_L0.595––
XDP_PCH_PWRGD1.155––
XDP_PCH_TCK0.052––
XDP_PCH_TDO0.079––
XDP_PIN030.556––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP3V42_G3H read on the 820-3299?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3299: diode 0.326. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP5V_S5 read on the 820-3299?

OpenBoardData's known-good values for PP5V_S5 on the 820-3299: diode 0.400. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S5 read on the 820-3299?

OpenBoardData's known-good values for PP3V3_S5 on the 820-3299: diode 0.150. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3299 board?

Open your own 820-3299 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License