Apple laptop board · OpenBoardData

820-3209 known-good readings

Known-good readings for the Apple laptop board 820-3209: 148 nets, including 8 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 8 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3209.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 8 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

G3H: always on 2

Should be there as soon as a charger or battery is connected.

NetDiodeVoltageResistance
PP3V42_G3H0.29––
AI: what PP3V42_G3H is and how to check it

PP3V42_G3H is the always-on 3.42 V rail, judged from its name (G3H = always on); it should be present whenever the board has power. The only known-good reading here is a diode value of 0.29 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage on the rail. No known-good voltage reading is available here, so compare against a matching rail or a known-good board. A diode reading far from 0.29 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault.

PPDCIN_G3H_OR_PBUS1.030––
AI: what PPDCIN_G3H_OR_PBUS is and how to check it
  • What it is: From the name, PPDCIN_G3H_OR_PBUS is the main DC input rail, fed either from the charger (PPDCIN) or from the USB power bus (PBUS). The G3H suffix means it is always-on whenever power is connected, before the machine starts.
  • Known-good reading: Diode mode to ground is 1.030 (community value, a guide only). No known-good voltage reading is recorded here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the DC voltage on the rail.
  • If it's far off: A diode reading well below known-good usually points to a short or a leaky part on the rail; a much higher or open reading suggests a broken feed path. Confirm with the voltage measurement before replacing anything.

S5 and SUS: standby 3

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP1V2_S5_SMC_VDDCOL––
AI: what PP1V2_S5_SMC_VDDC is and how to check it

PP1V2_S5_SMC_VDDC is a 1.2 V rail for the SMC, in the S5 standby stage — both from the name. The only archived reading is a diode value of OL to ground, with no condition or voltage recorded, so there is no known-good voltage or resistance here. Check it unpowered in diode mode from the rail to ground, then measure the voltage with power applied and compare against a matching rail or a known-good board. A far-off diode reading usually points to a short or an open in that rail's path, but one reading doesn't confirm a bad part.

PP3V3_S5_AVREF_SMC0.54––
AI: what PP3V3_S5_AVREF_SMC is and how to check it

PP3V3_S5_AVREF_SMC is a 3.3 V standby rail feeding the SMC's analog reference, judging by the name (S5 = standby, AVREF = analog reference). The only known-good reading here is a diode value of 0.54 to ground; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the net to ground, then power the board and measure the voltage at the net. A diode reading far below 0.54 usually points to a short or leaky part on the rail; a reading well above it suggests an open path. Confirm with a voltage measurement before replacing anything, since a single reading can mislead.

PP3V3_S5_SMC_VDDA0.29––
AI: what PP3V3_S5_SMC_VDDA is and how to check it
  • What it is: PP3V3_S5_SMC_VDDA is a 3.3 V standby rail feeding the SMC's analog supply, judging from the name (PP = power rail, 3V3 = 3.3 V, S5 = standby stage, SMC_VDDA = SMC analog supply). That's from the name, not from board data.
  • Known-good reading: diode 0.29 in the archive. This is a community figure and a guide only; it varies with board state.
  • How to check: with the board unpowered, measure diode mode from the rail to ground; then apply power and measure the voltage, which should sit near 3.3 V.
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board before condemning anything.

S3: memory 1

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP3V3_S3–3.300–
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is a 3.3 V rail; the S3 suffix, from its name, places it in the memory stage of the power sequence. The archive lists one known-good voltage of 3.300 V for this rail, with no condition recorded, and no known-good diode or resistance reading. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A voltage far from 3.300 V points to the rail not coming up or being loaded down, but with no known-good diode value here, compare the diode reading against a matching rail or a known-good board before suspecting a part.

S0: running 2

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP3V3_S0_SSD_FLT0.299––
AI: what PP3V3_S0_SSD_FLT is and how to check it

PP3V3_S0_SSD_FLT is a 3.3 V rail, from its name: the S0 suffix means it belongs to the running state, and SSD_FLT suggests it feeds the SSD circuitry. The only known-good reading here is a diode value of 0.299 to ground; there is no known-good voltage reading in this data. Check it with the board unpowered in diode mode from the rail to ground, then power up and measure the voltage on the rail. A diode reading far from 0.299 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault, so compare with a matching rail or a known-good board.

PPVCCSA_S0_REG_R0.00––
AI: what PPVCCSA_S0_REG_R is and how to check it
  • What it is: From the name, PPVCCSA_S0_REG_R is a regulated supply rail (REG) for VCCSA, active in the S0 running state. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.00 to ground, with no condition given. That's the only value recorded here; there's no known-good voltage or resistance reading for this rail.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then power the board and measure the voltage on the rail.
  • What a far-off reading suggests: A diode reading well above 0.00 where the rail should be a near-short usually points to an open trace or missing connection rather than a shorted part. Confirm with the voltage measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
ALL_SYS_PWRGD0.42––
AP_CLKREQ_L_R–3.300–
AP_CLKREQ_Q_L–3.300–
AP_PWR_EN–3.300–
AP_RESET_CONN_L–3.300–
AP_RESET_L–3.300–
CPU_CATERR_L0.31––
CPU_PECI_R0.12––
CPU_PROCHOT_L0.03––
CPU_THRMTRIP_3V31.06––
CPUVSENSE_IN0.00––
DOCK_PWR20–20.000 Normal–
DP_TBTSNK1_HPD0.00––
G3_POWERON_L1.81––
GND_SMC_AVSS0.00––
KBDLED_ANODE0.587––
KBDLED_FBOL––
LPC_AD<0>0.48––
LPC_AD<1>0.48––
LPC_AD<2>0.48––
LPC_AD<3>0.48––
LPC_CLK33M_SMC0.51––
LPC_FRAME_L0.49––
LPC_PWRDWN_L0.50––
LPC_SERIRQ0.53––
MEM_EVENT_LOL––
N8905060–3.300 Normal–
PCIE_CLK100M_SSD_N0.365––
PCIE_CLK100M_SSD_P0.365––
PCIE_SSD_D2R_N<1>0.287––
PCIE_SSD_D2R_P<1>0.285––
PCIE_SSD_R2D_N<1>OL––
PCIE_SSD_R2D_P<1>OL––
PM_CLKRUN_L0.54––
PM_DSW_PWRGD0.71––
PM_PCH_SYS_PWROK0.70––
PM_PWRBTN_L0.52––
PM_SLP_S3_L0.45––
PM_SLP_S4_L0.45––
PM_SLP_S5_L0.50––
PM_SYSRST_L0.54––
PP1V2_S5_SMC_VDDCOL––
PP3V3_S0_SSD_FLT0.299––
PP3V3_S3–3.300–
PP3V3_S5_AVREF_SMC0.54––
PP3V3_S5_SMC_VDDA0.29––
PP3V3_TPAD_CONNOL––
PP3V3_WLAN_F–3.300–
PP3V3_WLAN_R–3.300–
PP3V42_G3H0.29––
PP5V_TPAD_FILT0.430––
PPDCIN_G3H_OR_PBUS1.030––
PPVCCSA_S0_REG_R0.00––
S5_PWRGD0.41––
SATA_PCIE_SEL0.740––
SATA_SSD_D2R_N0.739––
SATA_SSD_D2R_P0.739––
SATA_SSD_R2D_N0.740––
SATA_SSD_R2D_P0.740––
SMBUS_SMC_0_S0_SCL1.30––
SMBUS_SMC_0_S0_SDA1.30––
SMBUS_SMC_1_S0_SCL0.49––
SMBUS_SMC_1_S0_SDA0.49––
SMBUS_SMC_2_S3_SCL0.65––
SMBUS_SMC_2_S3_SDA0.65––
SMBUS_SMC_3_SCL0.58––
SMBUS_SMC_3_SDA0.57––
SMBUS_SMC_5_G3_SCL0.47––
SMBUS_SMC_5_G3_SDA0.47––
SMC_1V5S3_ISENSE1.50––
SMC_3V3S0_ISENSEOL––
SMC_ADAPTER_EN0.49––
SMC_ADC23OL––
SMC_BATLOW_L0.75––
SMC_BC_ACOK0.49––
SMC_BIL_BUTTON_L1.81––
SMC_BMON_ISENSEOL––
SMC_CLK32K0.51––
SMC_CPU_ISENSE1.44––
SMC_CPU_SA_ISENSEOL––
SMC_CPU_VSENSE1.10––
SMC_CPUVCCIO_ISENSEOL––
SMC_DCIN_ISENSEOL––
SMC_DCIN_VSENSE1.24––
SMC_DEBUGPRT_EN_L0.50––
SMC_DEBUGPRT_RX_L0.52––
SMC_DEBUGPRT_TX_L0.54––
SMC_DELAYED_PWRGD0.64––
SMC_EXTALOL––
SMC_FAN_0_CTLOL––
SMC_FAN_0_TACHOL––
SMC_GFX_ISENSE1.44––
SMC_GFX_VSENSE1.10––
SMC_HDD_ISENSEOL––
SMC_HS_COMPUTING_ISENSE1.50––
SMC_LCDBKLT_ISENSEOL––
SMC_LID0.439––
SMC_LRESET_L0.39––
SMC_ODD_DETECTOL––
SMC_ONOFF_L0.608––
SMC_OOB1_RX_L0.704––
SMC_OOB1_TX_L0.704––
SMC_OTHER_HI_ISENSEOL––
SMC_PBUS_VSENSE1.23––
SMC_PECI_LOL––
SMC_PM_G2_EN0.41––
SMC_PME_S4_DARK_L0.38––
SMC_PME_S4_WAKE_L0.58––
SMC_PROCHOTOL––
SMC_RESET_L0.44––
SMC_RUNTIME_SCI_L0.53––
SMC_RX_LOL––
SMC_S4_WAKESRC_EN0.67––
SMC_S5_PWRGD_VINOL––
SMC_SYS_KBDLED0.62––
SMC_TCK1.81––
SMC_TDI1.82––
SMC_TDO1.80––
SMC_THRMTRIP1.69––
SMC_TMS1.81––
SMC_TPAD_RST_L0.617––
SMC_TX_L1.81––
SMC_VCCIO_CPU_DIV2OL––
SMC_VCCSA_VSENSE1.10––
SMC_WAKE_LOL––
SMC_WAKE_SCI_L0.52––
SMC_WLAN_ISENSEOL––
SMC_XTALOL––
SMS_INT_L1.80––
SPI_DESCRIPTOR_OVERRIDE_LOL––
SPI_SMC_CLK0.51––
SPI_SMC_CS_L0.50––
SPI_SMC_MISO0.47––
SPI_SMC_MOSI0.47––
SSD_CLKREQ_L0.500––
SSD_RESET_L0.600––
SYS_ONEWIREOL––
UNCONNECTED_269OL––
USB_BT_WAKE_N0.00––
USB_SMC_NOL––
USB_SMC_POL––
USB_TPAD_N0.668––
USB_TPAD_P0.673––
VCC3M–3.300 Normal–
VCC5M–5.000 Normal–
VINT20–20.000 Normal–
VL5–5.000 Normal–
WIFI_EVENT_L0.68––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP3V42_G3H read on the 820-3209?

OpenBoardData's known-good values for PP3V42_G3H on the 820-3209: diode 0.29. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S3 read on the 820-3209?

OpenBoardData's known-good values for PP3V3_S3 on the 820-3209: voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3209 board?

Open your own 820-3209 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License