Apple laptop board · OpenBoardData

820-3071 known-good readings

Known-good readings for the Apple laptop board 820-3071: 227 nets, including 23 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 23 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-3071.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 23 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

S4 2

Follow as the board starts to wake.

NetDiodeVoltageResistance
PP3V3_S40.366––
AI: what PP3V3_S4 is and how to check it

PP3V3_S4 is a 3.3 V rail in the S4 startup stage, judging from its name. The archive lists one known-good diode reading of 0.366 to ground; no known-good voltage reading is recorded here. With the board unpowered, measure diode mode from PP3V3_S4 to ground and compare with 0.366, then power up and check the rail's voltage. A diode reading far from 0.366 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP5V_S40.500––
AI: what PP5V_S4 is and how to check it

PP5V_S4 is a 5 V rail in the S4 startup stage, judged from its name; the archive has no board file, so the parts on it aren't known. The only known-good reading here is a diode value of 0.500 to ground, with no condition recorded. With the board unpowered, measure diode mode from PP5V_S4 to ground and compare; then power up and check the voltage. A diode reading far below 0.500 suggests a short or leaky load on the rail, but one reading isn't proof, so confirm before replacing anything. No known-good voltage reading is available here.

S3: memory 8

Stay on in sleep, keeping the memory alive.

NetDiodeVoltageResistance
PP1V2_S3_SD_DVDD120.292––
AI: what PP1V2_S3_SD_DVDD12 is and how to check it
  • What it is: From the name, a 1.2 V rail in the S3 (memory) startup stage, feeding SD card DVDD12. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.292 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground, then power on and measure the voltage at the rail.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a much higher one suggests an open path. One reading alone doesn't confirm a bad part, so compare with a matching rail or a known-good board before replacing anything.
PP3V3_S30.502––
AI: what PP3V3_S3 is and how to check it

PP3V3_S3 is the 3.3 V rail that comes up at the S3 (memory) stage of startup, judging from its name. The only archived reading is a diode value of 0.502 to ground, with no condition recorded and no known-good voltage or resistance here.

  • Check it unpowered in diode mode, red probe on ground, black on the rail, and compare with 0.502.
  • Then power the board and measure the voltage at the rail; no known-good voltage is listed here, so compare against a known-good board or the rail's nominal 3.3 V.
  • A diode reading far below 0.502 suggests a short or a leaky part on the rail; far above suggests an open path. One reading alone doesn't confirm a bad part.
PP3V3_S3_ENET_PHY_AVDDH0.471––
AI: what PP3V3_S3_ENET_PHY_AVDDH is and how to check it
  • What it is: From its name, PP3V3_S3_ENET_PHY_AVDDH is a 3.3 V rail (PP3V3) that comes up in the S3 memory stage and feeds the analog high-voltage supply (AVDDH) of the Ethernet PHY. That's an inference from the name only; the parts on the net aren't documented here.
  • Known-good: diode 0.471 to ground. No known-good voltage or resistance reading here.
  • How to check: Power off and unplugged, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If it's far off: a much lower diode reading suggests a shorted load on the rail; a missing voltage points to the rail's enable or supply upstream. Confirm with a second reading before replacing anything.
PP3V3_S3_ENET_PHY_BIASVDDH0.471––
AI: what PP3V3_S3_ENET_PHY_BIASVDDH is and how to check it

PP3V3_S3_ENET_PHY_BIASVDDH is a 3.3 V S3 rail feeding the Ethernet PHY bias supply; the S3 and ENET/PHY parts come from the name, and S3 is a memory-stage rail. The only known-good reading here is a diode value of 0.471; there is no known-good voltage or resistance reading for this rail. Check it with the board unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. A diode reading far from 0.471 usually points to a short or a leaky part on that rail, but one reading isn't proof, so compare against a matching rail or a known-good board before replacing anything.

PP3V3_S3_ENET_PHY_XTALVDDH0.470––
AI: what PP3V3_S3_ENET_PHY_XTALVDDH is and how to check it
  • What it is: From its name, a 3.3 V S3 (memory-stage) rail feeding the Ethernet PHY's crystal/oscillator supply (XTALVDDH). The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.470 in diode mode to ground, board unpowered. No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the net to ground and compare with 0.470; then power on and measure the voltage at the net, expecting about 3.3 V (general expectation from the name, not a recorded value).
  • If it's far off: a much lower diode reading suggests a short or leaky part on the rail; an open/high reading suggests a missing feed or broken trace. Confirm with a second measurement before replacing anything.
PP3V3_S3RS4_BT_F0.366––
AI: what PP3V3_S3RS4_BT_F is and how to check it
  • What it is: From the name, PP3V3_S3RS4_BT_F is a 3.3 V rail in the S3 (memory) startup stage, with the BT_F suffix suggesting a Bluetooth-related branch. The exact parts on it aren't documented here.
  • Known-good reading: diode 0.366 (community value, a guide only). No known-good voltage reading here.
  • How to check: power off, measure diode mode from the rail to ground; then power on and measure the voltage, expecting about 3.3 V.
  • If far off: a much lower diode reading usually points to a shorted load or capacitor on the rail; a much higher one to an open trace or missing supply. Confirm with the voltage before replacing anything.
PP5V_S3_RTUSB_B_F0.488––
AI: what PP5V_S3_RTUSB_B_F is and how to check it

PP5V_S3_RTUSB_B_F is a 5 V rail that, from its name, is switched in the S3 (memory) state and feeds the rear USB-B port. The only known-good reading here is a diode value of 0.488 to ground; no known-good voltage is recorded. With the board unpowered, measure diode mode from the rail to ground and compare against 0.488, then apply power and check the voltage. A diode reading far from 0.488 usually points to a short or leaky component on that rail, but one reading isn't proof a part is bad.

PP5V_S3_RTUSB_B_ILIM0.488––
AI: what PP5V_S3_RTUSB_B_ILIM is and how to check it
  • What it is: From the name, a 5 V S3 (memory-stage) rail feeding the RTUSB_B current-limit (ILIM) point. The archive only has a diode reading, so no voltage or resistance value is known-good here.
  • Known-good: diode 0.488 to ground, board unpowered.
  • How to check: power off, diode mode, red probe to ground, black to the net; then power on and measure the voltage, comparing against the S3 state.
  • If far off: a much lower diode reading suggests a short or leaky part on that net; a much higher one suggests an open path. Confirm with voltage before replacing anything.

S0: running 13

Only there when the machine is fully on.

NetDiodeVoltageResistance
PP1V2_S0_SD_AVDD120.292––
AI: what PP1V2_S0_SD_AVDD12 is and how to check it
  • What it is: From the name, PP1V2_S0_SD_AVDD12 is a 1.2 V rail that runs in the S0 (running) state, likely an SD-related supply. The board data doesn't list which parts sit on it.
  • Known-good reading: diode 0.292 to ground, from the readings archive (community-contributed, so a guide only). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.292; then power up and measure the voltage, expecting about 1.2 V from the name.
  • If far off: a much lower diode reading suggests a short or leaky part on the rail; a high or open reading suggests a broken feed. Confirm with a second measurement before replacing anything.
PP1V2_S0_SD_VUHS10.432––
AI: what PP1V2_S0_SD_VUHS1 is and how to check it
  • What it is: PP1V2_S0_SD_VUHS1 is a 1.2 V rail, from its name. The S0 part means it's up in the running state; the SD/VUHS1 part suggests it feeds the SD card interface's UHS-1 signalling supply. That's from the name only — the parts on it aren't known here.
  • Known-good reading: diode 0.432 to ground, from the readings archive (community-contributed, so a guide, not a guarantee). No known-good voltage reading here.
  • How to check: power off and unplug, then diode mode from the rail to ground and compare with 0.432. Then power on and measure the voltage; it should sit near 1.2 V when the board is running.
  • If it's far off: a much lower diode reading usually points to a short or a failed part on the rail; a correct diode reading with no voltage points upstream, at the rail's supply or its enable. Confirm with a second measurement before replacing anything.
PP1V5_S00.250––
AI: what PP1V5_S0 is and how to check it

PP1V5_S0 is a 1.5 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "PP" typically marks a power rail. The readings archive lists a known-good diode reading of 0.250 to ground for this net; no known-good voltage reading is recorded here. Check it with the board unpowered in diode mode from PP1V5_S0 to ground, then power up and measure the voltage. A diode reading far from 0.250 usually points to a short or a faulty part on that rail, but one reading alone doesn't confirm a bad part.

PP1V05_S0_LDOOL––
AI: what PP1V05_S0_LDO is and how to check it

PP1V05_S0_LDO is a 1.05 V rail; the "S0" in its name indicates it belongs to the running (S0) power state, and "LDO" suggests it comes from a low-dropout regulator. The only archived reading for this net is a diode value of OL (open), with no known-good voltage or resistance reading recorded here. Check it unpowered in diode mode from the net to ground, then measure the voltage with the board powered in S0. A diode reading far from OL, or a voltage well off 1.05 V, usually points to a short or a fault in the LDO feeding it, but one reading alone doesn't confirm a bad part.

PP1V5_S0_P1V05_LDOOL––
AI: what PP1V5_S0_P1V05_LDO is and how to check it

PP1V5_S0_P1V05_LDO — from the name, a 1.5 V rail that is on in S0 (running) state, with a 1.05 V LDO feed implied by the name. The archive holds one reading for this net: diode mode to ground is OL (open, no conduction path). That is a community reading and only a guide, and there is no known-good voltage or resistance value here.

  • Check it with the board unpowered: meter in diode mode, black probe on ground, red on the net, and confirm the OL.
  • Then power the board and measure the voltage on the net; compare against the 1.5 V the name implies, not against an archived value, since none exists.
  • A diode reading far from OL (a low number) usually points to a short or a partly shorted load on the rail; OL itself is the expected open here, so a low reading is the thing to chase.
  • With no voltage or resistance reference in the archive, a matching rail on a known-good board is the best comparison.
PP3V3_S00.429––
AI: what PP3V3_S0 is and how to check it

PP3V3_S0 is the 3.3 V supply rail that is on in the S0 (running) state, judging by its name. The archive lists one known-good diode reading for it: 0.429 to ground, with the board unpowered. Check it in diode mode with power off, then measure the voltage with the board powered and running; no known-good voltage reading is recorded here. A diode value far from 0.429 usually points to a short or a leaky part on the rail, but a single reading isn't proof, so compare against a matching net or a known-good board before replacing anything.

PP3V3_S0_P1V05_LDO_BIASOL––
AI: what PP3V3_S0_P1V05_LDO_BIAS is and how to check it
  • What it is: From the name, PP3V3_S0_P1V05_LDO_BIAS is a 3.3 V rail active in the S0 (running) state, tied to a 1.05 V LDO bias supply. The name alone doesn't confirm which parts it feeds.
  • Known-good reading: The archive lists a diode reading of OL (open, no conduction to ground) for this net. No voltage or resistance value is recorded here.
  • How to check: With the board unpowered, measure diode mode from the net to ground; OL is the expected result. Then apply power and measure the voltage on the rail.
  • If it's far off: A low diode reading where OL is expected usually points to a short or a failed component on that net, but one reading isn't proof — confirm with a second measurement before replacing anything.
PP3V3_S0_SD_AVDD330.418––
AI: what PP3V3_S0_SD_AVDD33 is and how to check it
  • What it is: From its name, PP3V3_S0_SD_AVDD33 is a 3.3 V rail that runs in the S0 (running) state, feeding an SD-related AVDD33 supply. The board data is readings-only, so the parts on this net aren't listed.
  • Known-good reading: Diode 0.418 to ground, with no condition noted. There is no known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground and compare with 0.418. Then power up and measure the voltage, expecting about 3.3 V from the name (general expectation, not a logged value).
  • What a far-off reading suggests: A much lower diode reading points to a short or a leaky part on the rail; a much higher one points to an open feed or a missing enable. Confirm with the voltage measurement before replacing anything.
PP3V3_S0_SD_CONN0.420––
AI: what PP3V3_S0_SD_CONN is and how to check it

PP3V3_S0_SD_CONN is a 3.3 V rail that is on in the S0 (running) state, judging from its name; it appears to feed the SD connector area. The archive lists one known-good reading: diode mode to ground of 0.420, with no condition noted. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading is recorded here, so compare against a matching 3.3 V S0 rail or a known-good board. A diode reading far below 0.420 usually points to a short or a failing part on the rail, but one reading alone doesn't confirm a bad part.

PP3V3_S0_SW_SD_PWR0.578––
AI: what PP3V3_S0_SW_SD_PWR is and how to check it
  • What it is: From the name, PP3V3_S0_SW_SD_PWR is a 3.3 V switched supply for SD power, active in the S0 (running) state. It's a switched rail, so it may only come up when the board enables it.
  • Known-good reading: diode 0.578 to ground, from the readings archive (a community guide, not a factory spec). No known-good voltage reading here.
  • How to check: with the board unpowered, measure diode mode from the rail to ground and compare with 0.578. Then apply power, bring the board to S0, and measure the voltage on the rail.
  • What a far-off reading suggests: a diode value well below known-good usually points to a short or a leaky part on the rail; a much higher or open reading suggests a broken connection or a part not conducting. A missing voltage in S0 points to the enable or upstream supply, not necessarily the rail itself. Confirm with a second measurement before replacing anything.
PP3V3_S0SW_SD0.417––
AI: what PP3V3_S0SW_SD is and how to check it

PP3V3_S0SW_SD is a 3.3 V rail that, judging by its name, is switched and belongs to the SD circuit and is active in the S0 (running) state. The only known-good reading here is a diode value of 0.417 to ground, with no condition noted; there is no known-good voltage reading for this rail. With the board unpowered, measure diode mode from PP3V3_S0SW_SD to ground and compare with 0.417, then apply power and check the voltage appears when the board reaches S0. A diode reading far below 0.417 suggests a short or leaky load on the rail, while a much higher reading points to an open path; a missing voltage with a normal diode reading points upstream to the switch or its enable. These readings are community guides and vary with board state, so confirm against a matching rail or a known-good board before replacing anything.

PP5V_HDMI_DDC_S00.551––
AI: what PP5V_HDMI_DDC_S0 is and how to check it

PP5V_HDMI_DDC_S0 is a 5 V HDMI DDC rail that is present in the running (S0) state, judging by its name. The archive lists one known-good diode reading of 0.551 to ground; there is no known-good voltage reading here. With the board unpowered, measure diode mode from the rail to ground and compare with 0.551. Then power up in S0 and check the voltage is near 5 V. A diode reading far below 0.551 suggests a short or leaky part on the rail; far above it suggests an open path. These are guides from community readings, not confirmed values.

PP5V_HDMI_DDC_S0_F0.550––
AI: what PP5V_HDMI_DDC_S0_F is and how to check it

PP5V_HDMI_DDC_S0_F is a 5 V HDMI DDC rail; the S0 suffix in its name indicates it is present in the running state. The archive lists one known-good reading: diode 0.550 to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then confirm the voltage with the board powered in S0. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.550 usually points to a short or a leaky part on the rail, but one reading alone doesn't confirm a fault.

Every net with a reading

NetDiodeVoltageResistance
AP_CLKREQ_L0.466––
AP_CLKREQ_Q_L0.466––
AP_CLKREQ_R_L0.466––
AP_RESET_CONN_L0.467––
AP_RESET_CONN_R_L0.468––
AP_RESET_L0.468––
BCM57765_CS_L0.760––
BCM57765_MISO0.752––
BCM57765_MOSI0.758––
BCM57765_RDAC0.598––
BCM57765_SCLK0.758––
BCM57765_SMB_CLK0.751––
BCM57765_SMB_DATA0.751––
BDM57765_SR_DISABLE0.601––
DPMUX_ROM_WC_L0.647––
ENABLE_HDMI_DDC_S0OL––
ENABLE_HDMI_DDC_S0_ROL––
ENET_CLK25M_XTALI0.795––
ENET_CR_PWREN0.707––
ENET_LOW_PWR0.762––
ENET_RESET_L0.469––
ENET_RESET_L_R0.469––
ENET_SR_LX0.302––
ENET_VMAIN_PRSNT0.753––
ENET_WAKE_R_L0.603––
EQ_I2C_ADDR00.483––
HDMI_3V3_PWR_EN0.543––
HDMI_CLK_C_LS_NOL––
HDMI_CLK_C_LS_POL––
HDMI_CLK_LS_N0.670––
HDMI_CLK_LS_P0.642––
HDMI_CLK_N0.457––
HDMI_CLK_P0.457––
HDMI_DATA_C_N<0>OL––
HDMI_DATA_C_N<1>OL––
HDMI_DATA_C_N<2>OL––
HDMI_DATA_C_P<0>OL––
HDMI_DATA_C_P<1>OL––
HDMI_DATA_C_P<2>OL––
HDMI_DATA_LS_N<0>0.644––
HDMI_DATA_LS_N<1>0.670––
HDMI_DATA_LS_N<2>0.670––
HDMI_DATA_LS_P<0>0.644––
HDMI_DATA_LS_P<1>0.642––
HDMI_DATA_LS_P<2>0.642––
HDMI_DATA_N<0>0.456––
HDMI_DATA_N<1>0.456––
HDMI_DATA_N<2>0.456––
HDMI_DATA_P<0>0.456––
HDMI_DATA_P<1>0.456––
HDMI_DATA_P<2>0.456––
HDMI_DDC_CLK_5V0.577––
HDMI_DDC_CLK_CONN0.599––
HDMI_DDC_CLK_F0.598––
HDMI_DDC_DATA_5V0.578––
HDMI_DDC_DATA_CONN0.598––
HDMI_DDC_DATA_F0.597––
HDMI_DDC_LS_CLK0.490––
HDMI_DDC_LS_CLK_R0.492––
HDMI_DDC_LS_DATA0.490––
HDMI_DDC_LS_DATA_R0.493––
HDMI_HPD0.482––
HDMI_HPD_CONN0.669––
HDMI_HPD_F0.670––
HDMI_HPD_L0.620––
HDMI_HPD_R0.480––
HDMI_HPD_SINK0.482––
HDMI_HPD_SNK_R0.490––
HDMI_MIDOL––
HDMI_OC_L0.555––
I2C_HDMIRDRV_SCL_CONN0.484––
I2C_HDMIRDRV_SDA_CONN0.484––
I2C_X29THMSNS_SCL_CONNOL––
I2C_X29THMSNS_SDA_CONNOL––
LS_CFG_I2C_ADDR10.000––
LS_I2C_CTL_EN0.541––
LS_ISET0.543––
LS_PWR_DWN_L0.490––
P1V05S0_LDO_FBOL––
P1V5S0_LDO_PGOODOL––
P1V05S0_LDO_SSOL––
P3V3_SD_FET_RAMP0.710––
P3V3WLAN_VMON0.467––
PCIE_AP_D2R_NOL––
PCIE_AP_D2R_POL––
PCIE_AP_R2D_NOL––
PCIE_AP_R2D_POL––
PCIE_CLK100M_AP_NOL––
PCIE_CLK100M_AP_POL––
PCIE_CLK100M_ENET_N0.623––
PCIE_CLK100M_ENET_P0.598––
PCIE_ENET_D2R_NOL––
PCIE_ENET_D2R_POL––
PCIE_ENET_R2D_C_NOL––
PCIE_ENET_R2D_C_POL––
PCIE_WAKE_LOL––
PM_SLP_S3_L0.541––
PM_SLP_S4_L0.486––
PM_WLAN_EN0.465––
PP1V2_ENET0.304––
PP1V2_ENET_PHY_AVDDL0.303––
PP1V2_ENET_PHY_GPHYPLL0.303––
PP1V2_ENET_PHY_PCIEPLL0.303––
PP1V2_S0_SD_AVDD120.292––
PP1V2_S0_SD_VUHS10.432––
PP1V2_S3_SD_DVDD120.292––
PP1V5_HDMI_VDDRX0.249––
PP1V5_HDMI_VDDTA0.252––
PP1V5_HDMI_VDDTX0.250––
PP1V5_S00.250––
PP1V05_S0_LDOOL––
PP1V5_S0_P1V05_LDOOL––
PP1V5R1V05_HDMI_VDD0.250––
PP3V3_ENET0.470––
PP3V3_HDMI0.431––
PP3V3_HDMI_VDD330.425––
PP3V3_S00.429––
PP3V3_S0_P1V05_LDO_BIASOL––
PP3V3_S0_SD_AVDD330.418––
PP3V3_S0_SD_CONN0.420––
PP3V3_S0_SW_SD_PWR0.578––
PP3V3_S0SW_SD0.417––
PP3V3_S30.502––
PP3V3_S3_ENET_PHY_AVDDH0.471––
PP3V3_S3_ENET_PHY_BIASVDDH0.471––
PP3V3_S3_ENET_PHY_XTALVDDH0.470––
PP3V3_S3RS4_BT_F0.366––
PP3V3_S40.366––
PP3V3_WLAN0.526––
PP3V3_WLAN_F0.524––
PP3V3R1V8_ENET_LR_OUT_REG0.549––
PP5V_HDMI_DDC_CONN0.542––
PP5V_HDMI_DDC_FUSE0.550––
PP5V_HDMI_DDC_S00.551––
PP5V_HDMI_DDC_S0_F0.550––
PP5V_S3_RTUSB_B_F0.488––
PP5V_S3_RTUSB_B_ILIM0.488––
PP5V_S40.500––
PREQ0.542––
REXT_LS0.480––
SD_CLKREQ_L0.472––
SD_DETECT_L0.463––
SD_PWR_EN0.467––
SD_PWR_EN_R0.466––
SD_PWR_EN_SAK_R0.467––
SD_RESET_L0.477––
SD_RESET_R_L0.711––
SD_RTERM0.670––
SD_SPI_CLK0.725––
SD_SPI_CS_L0.721––
SD_SPI_HOLD_LOL––
SD_SPI_MISO0.726––
SD_SPI_MOSI0.725––
SD_SPI_WP_LOL––
SDCLK_CLK25M_X20.588––
SDCONN_CLK0.470––
SDCONN_CLK_R0.503––
SDCONN_CLK_R_L0.503––
SDCONN_CMD0.470––
SDCONN_CMD_R0.503––
SDCONN_DATA<0>0.470––
SDCONN_DATA<1>0.470––
SDCONN_DATA<2>0.470––
SDCONN_DATA<3>0.469––
SDCONN_DETECT_L0.472––
SDCONN_DETECT_L_R0.471––
SDCONN_OC_L0.581––
SDCONN_R_DATA<0>0.504––
SDCONN_R_DATA<1>0.503––
SDCONN_R_DATA<2>0.503––
SDCONN_R_DATA<3>0.502––
SDCONN_R_DATA<4>OL––
SDCONN_R_DATA<5>OL––
SDCONN_R_DATA<6>OL––
SDCONN_R_DATA<7>OL––
SDCONN_STATE_CHANGE0.473––
SDCONN_STATE_CHANGE_SAK_L0.432––
SDCONN_WP0.719––
SDSCLK_CLK25M_X10.525––
SLG_ENET_RESET_OUT_LOL––
TP_BCM57765_SPD100LED_L0.763––
TP_BCM57765_TRAFFICLED_L0.763––
TP_CE_L_MS_INS_LOL––
TPS2553_EN0.541––
TPS2553_ILIM0.570––
TPS2553_ILIM_ROL––
UNCONNECTED_160.690––
UNCONNECTED_170.734––
UNCONNECTED_180.734––
UNCONNECTED_190.734––
UNCONNECTED_200.735––
UNCONNECTED_210.731––
UNCONNECTED_220.720––
UNCONNECTED_230.720––
UNCONNECTED_240.720––
USB_BT_NOL––
USB_BT_POL––
USB_EXTB_F_NOL––
USB_EXTB_F_POL––
USB_EXTB_NOL––
USB_EXTB_OC_L0.516––
USB_EXTB_POL––
USB_ILIM0.518––
USB_ILIM_ROL––
USB_MIDOL––
USB_PWR_EN0.486––
USB_SD_DM0.732––
USB_SD_DP0.730––
USB3_EXTB_D2R_NOL––
USB3_EXTB_D2R_POL––
USB3_EXTB_R2D_C_NOL––
USB3_EXTB_R2D_C_POL––
USB3_EXTB_R2D_NOL––
USB3_EXTB_R2D_POL––
USB3_EXTB_RX_NOL––
USB3_EXTB_RX_POL––
USB3_EXTB_TX_NOL––
USB3_EXTB_TX_POL––
USB3_SD_D2R_C_N0.357––
USB3_SD_D2R_C_P0.357––
USB3_SD_D2R_NOL––
USB3_SD_D2R_POL––
USB3_SD_R2D_C_NOL––
USB3_SD_R2D_C_POL––
USB3_SD_R2D_N0.360––
USB3_SD_R2D_P0.369––
WIFI_EVENT_LOL––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

What should PP5V_S4 read on the 820-3071?

OpenBoardData's known-good values for PP5V_S4 on the 820-3071: diode 0.500. Readings vary with the board's state and the meter, so treat them as a guide.

What should PP3V3_S0 read on the 820-3071?

OpenBoardData's known-good values for PP3V3_S0 on the 820-3071: diode 0.429. Readings vary with the board's state and the meter, so treat them as a guide.

How do I see these readings on my 820-3071 board?

Open your own 820-3071 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License