Apple laptop board · OpenBoardData

820-02382 known-good readings

Known-good readings for the Apple laptop board 820-02382: 116 nets, including 7 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 7 of its rails: what each one is and how to check it.

Last updated

Name the file with the board number, as in 820-02382.brd, and these readings show on its pins as you hover. Your file stays on your computer.

With your board open in the viewer

  • Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
  • Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
  • Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.

Power rails by startup stage

Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 7 rails with readings, in the order a board brings them up. The schematic has the final word.

Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.

S5 and SUS: standby 7

Come up once the always-on rails are good, before the power button.

NetDiodeVoltageResistance
PP0V9_NAND0_S5E3_VDD_PLL0.270––
AI: what PP0V9_NAND0_S5E3_VDD_PLL is and how to check it

PP0V9_NAND0_S5E3_VDD_PLL is a 0.9 V standby rail feeding the NAND PLL supply; the S5/SUS part of the name marks it as a standby-stage rail. The only known-good reading here is a diode value of 0.270 to ground, with no condition recorded. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. No known-good voltage reading is available for this rail. A diode reading far from 0.270 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP0V9_NAND1_S5E1_VDD_PLL0.440––
AI: what PP0V9_NAND1_S5E1_VDD_PLL is and how to check it

PP0V9_NAND1_S5E1_VDD_PLL is a 0.9 V rail feeding the NAND PLL, judging from the name; the S5E1/SUS part of the name puts it in the standby stage. The archive has one known-good reading: diode 0.440 to ground, with no condition noted. Check it with the board unpowered in diode mode, red probe on ground, black on the rail; then power up and measure the voltage, expecting about 0.9 V. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.440 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP0V9_NAND1_S5E3_VDD_PLL0.440––
AI: what PP0V9_NAND1_S5E3_VDD_PLL is and how to check it
  • What it is: From the name, a 0.9 V rail feeding the PLL supply of a NAND device, in the S5/SUS standby state. The board data doesn't list which parts sit on it.
  • Known-good: Diode reading to ground is 0.440 (community value, a guide only; board state affects it). No known-good voltage reading here.
  • How to check: Power off, measure diode mode from the rail to ground. Then power up and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.440 suggests a short or leaky load on the rail; a much higher or open reading suggests a broken trace or missing connection. Confirm with a second measurement before replacing anything.
PP1V2_NAND0_S5E3_AVDD1X_PLL0.225––
AI: what PP1V2_NAND0_S5E3_AVDD1X_PLL is and how to check it

PP1V2_NAND0_S5E3_AVDD1X_PLL is a 1.2 V rail feeding the NAND storage area, and the name also marks it as an S5/SUS standby rail and a PLL supply (all from the name).

  • Known-good: diode 0.225 to ground, from the readings archive (a community value, so treat it as a guide; no condition is recorded).
  • No known-good voltage reading here.
  • Check it with the board unpowered in diode mode, red lead on ground, black on the rail; then power up and measure the voltage at the rail.
  • A diode reading far below 0.225 suggests a short or a leaky part on the rail; far above it suggests an open path. Confirm with a voltage check before replacing anything.
PP1V2_NAND1_S5E1_PCI_AVDD_H0.292––
AI: what PP1V2_NAND1_S5E1_PCI_AVDD_H is and how to check it

PP1V2_NAND1_S5E1_PCI_AVDD_H is a 1.2 V rail feeding NAND/PCI-side AVDD, and the S5/SUS in its name marks it as a standby-stage rail (from the name). The only known-good figure here is a diode reading of 0.292 to ground, with no condition recorded. Check it unpowered in diode mode from the rail to ground, then confirm the voltage with the board powered in standby. No known-good voltage reading here, so compare against a matching rail or a known-good board. A diode value far from 0.292 usually points to a short or a damaged part on that rail, but one reading alone doesn't confirm a fault.

PP1V2_NAND1_S5E2_PCI_AVDD_H0.292––
AI: what PP1V2_NAND1_S5E2_PCI_AVDD_H is and how to check it
  • What it is: From its name, PP1V2_NAND1_S5E2_PCI_AVDD_H is a 1.2 V rail feeding the NAND storage area, in the S5/SUS standby stage. The name suggests a supply for a PCIe/NAND interface, but the parts it feeds aren't documented here.
  • Known-good reading: Diode mode to ground, 0.292 (community reading, a guide only). No known-good voltage reading here.
  • How to check: Power off and unplug, then measure diode mode from the rail to ground. Then apply power and measure the voltage on the rail.
  • If it's far off: A diode reading well below 0.292 usually points to a short or a failing load on the rail; a much higher or open reading points to a broken feed or a missing enable. Confirm with the voltage measurement before suspecting any part.
PP1V2_NAND1_S5E3_PCI_AVDD_H0.292––
AI: what PP1V2_NAND1_S5E3_PCI_AVDD_H is and how to check it
  • What it is: From the name, a 1.2 V rail feeding NAND/PCIe AVDD, active in S5/SUS standby. The archive has no parts list for this net.
  • Known-good reading: diode 0.292 (no condition given). No known-good voltage or resistance here.
  • How to check: power off, diode mode from the rail to ground; then power applied, measure the voltage.
  • If far off: a low diode reading suggests a short or leaky load on the rail; a high one suggests an open path. Confirm with a second measurement before replacing anything.

Every net with a reading

NetDiodeVoltageResistance
AUD_DMIC0_CLK_CONN0.490––
AUD_DMIC0_DATA_CONN0.640––
AUD_DMIC1_CLK_CONN0.500––
AUD_DMIC1_DATA_CONN0.640––
CHGR_LL0.480–270.000k
CHGR_PHASE10.480–270.000k
CHGR_PHASE20.480–270.000k
I2C_KBD_SDA0.669––
IOXP_I2C_SCL0.676––
IOXP_I2C_SDA0.652––
KBDBKLT_SW20.380––
MPMU_BUCK5_LX00.223––
MPMU_BUCK5_LX10.223––
MPMU_BUCK5_LX20.223––
MPMU_BUCK5_LX30.223––
MPMU_BUCK6_LX00.425––
MPMU_BUCK9_LX00.209––
MPMU_BUCK10_LX00.122––
MPMU_BUCK10_LX10.122––
NAND0_JTAG_SEL0.300––
NAND0_JTAG_TRST_L0.300––
NAND0_OCARINA_TDEV10.770––
NAND0_S5E0_ZQ_00.300––
P0V9_LX0_NAND00.270––
P0V9_LX0_NAND10.440––
P0V9_LX1_NAND00.220––
P0V9_LX1_NAND10.440––
P1V2_LX0_NAND00.220––
P1V2_LX0_NAND10.292––
P2V5_NAND0_BST_R0.590––
P2V5_NAND0_PGOOD0.550––
P2V5_NAND0_SW0.280––
P2V5_NAND1_PGOOD0.550––
P2V5_NAND1_SW0.297––
P5VS2TPS_PHASE0.380––
P5VUSBC01_AGND0.000––
P5VUSBC01_SS0.720––
P5VUSBC01_SW0.300––
P5VUSBC23_FB1.406––
P5VUSBC23_FB_R0.460––
P5VUSBC23_RAOL––
P5VUSBC23_SS0.540––
P5VUSBC23_SW10.450––
P5VUSBC23_SW20.450––
PP0V9_NAND00.270––
PP0V9_NAND0_S5E3_VDD_PLL0.270––
PP0V9_NAND10.440––
PP0V9_NAND1_S5E1_VDD_PLL0.440––
PP0V9_NAND1_S5E3_VDD_PLL0.440––
PP0V81_S1_SRAM0.197––
PP0V575_S1_VDDQ10.122––
PP1V2_NAND00.220––
PP1V2_NAND0_S5E3_AVDD1X_PLL0.225––
PP1V2_NAND10.292––
PP1V2_NAND1_S5E1_PCI_AVDD_H0.292––
PP1V2_NAND1_S5E2_PCI_AVDD_H0.292––
PP1V2_NAND1_S5E3_PCI_AVDD_H0.292––
PP1V2_S20.255–0.001R
PP1V8_DMIC0.250––
PP1V8_S20.260–2.200k
PP1V8_S2SW0.312––
PP2V5_NAND00.280––
PP2V5_NAND10.296––
PP5V_KBDBKLT0.380––
PP5V_S2_MAIN0.380––
PP5V_S2SW_USBC010.300––
PP5V_S2SW_USBC230.450––
PPBUS_AON_LUXE0.470––
PPDCIN_AON_CHGR0.620––
PPDCIN_AON_CHGR_R0.620––
PPLUXE_INPUT_R_V0.470––
PPLUXE_LX10.430––
PPLUXE_LX20.430––
PPVBUS_USBC50.170––
PPVDD_AMPH1_S2SW0.425––
PPVDD_AVEMSR_AWAKESW0.223––
PPVDD_ECPU_AWAKE0.205––
PPVDD_ECPU_SRAM_AWAKE0.404––
PPVDD_FIXED_S10.209––
PPVDD_GPU_BMPR_S10.283––
PPVDD2H1_S2SW0.065––
PPVIN_5VUSBC010.470––
PPVIN_5VUSBC230.470––
PPVIN_P5VS20.470––
PPVOUT_KBDLED_CONN0.580––
PPVOUT_LUXE_XW0.610––
SPI_AOP_SENSOR_CLK0.318––
SPI_AOP_SENSOR_MOSI0.317––
SPI_AOP_SENSOR_MOSI_1V8_R0.497––
SPI_AOP_SENSOR_SCLK_1V8_R0.505––
USBC0_D2R_CR_N<1>OL––
USBC0_D2R_CR_N<2>OL––
USBC0_D2R_CR_P<1>OL––
USBC0_D2R_CR_P<2>OL––
USBC0_R2D_N<1>OL––
USBC0_R2D_N<2>OL––
USBC0_R2D_P<1>OL––
USBC0_R2D_P<2>OL––
USBC1_D2R_CR_N<1>OL––
USBC1_D2R_CR_N<2>OL––
USBC1_D2R_CR_P<1>OL––
USBC1_D2R_CR_P<2>OL––
USBC1_R2D_N<1>OL––
USBC1_R2D_N<2>OL––
USBC1_R2D_P<1>OL––
USBC1_R2D_P<2>OL––
USBC2_D2R_CR_N<1>OL––
USBC2_D2R_CR_N<2>OL––
USBC2_D2R_CR_P<1>OL––
USBC2_D2R_CR_P<2>OL––
USBC2_R2D_N<1>OL––
USBC2_R2D_N<2>OL––
USBC2_R2D_P<1>OL––
USBC2_R2D_P<2>OL––
USBC5_CC1_PIN0.600––
USBC5_CC1_RD0.470––

Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.

Frequently asked questions

How do I see these readings on my 820-02382 board?

Open your own 820-02382 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.

Where do these readings come from?

From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.

All boards · Board Viewer

Sources

  1. OpenBoardData. Known-good readings and repair notes; community data under the Open Database License