Apple laptop board · OpenBoardData
820-00138 known-good readings
Known-good readings for the Apple laptop board 820-00138: 28 nets, including 12 power rails sorted by startup stage, from OpenBoardData. Open your own copy of the board in the free Board Viewer to see them on the pins, trace the rails and ask AI about any part. AI explains 12 of its rails: what each one is and how to check it.
Name the file with the board number, as in 820-00138.brd, and these readings show on its pins as you hover. Your file stays on your computer.
With your board open in the viewer
- Readings on the pins. Hover over a pin for its known-good diode, voltage and resistance, and type your meter's reading to compare.
- Power AI. Draws these rails on the board in their startup stages, and steps through the power-up sequence where the notes have one.
- Ask AI. Click a part or net and ask about it. The answer uses this board's readings and notes, and its values are checked against them.
Power rails by startup stage
Apple writes a rail's power state into its name, as in PP3V3_S5. These are the 12 rails with readings, in the order a board brings them up. The schematic has the final word.
Each rail with an AI note was explained by AI (DeepSeek) from this board's readings and notes only, with every value in it checked against them. AI can be wrong: measure before you replace anything.
G3H: always on 2
Should be there as soon as a charger or battery is connected.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PPDCIN_G3H | – | 20.000 | – |
AI: what PPDCIN_G3H is and how to check itPPDCIN_G3H is the always-on DC input rail, as its G3H suffix indicates (from the name). The archive lists a known-good voltage of 20.000 V on this rail; there is no known-good diode or resistance reading here.
| |||
PPDCIN_G3H_CHGR | – | 20.000 | – |
AI: what PPDCIN_G3H_CHGR is and how to check itPPDCIN_G3H_CHGR is the charger-side DC input rail; the G3H in the name indicates it is always-on power, and the CHGR suffix ties it to the charger circuit. The only archived reading is 20.000 V, with no condition recorded; there is no known-good diode or resistance value for this net here. Check it unpowered in diode mode from the net to ground, then with the charger connected measure the voltage and compare with 20.000 V. A voltage far below that, or a near-short to ground, usually points to a fault on the input path or a shorted component on the rail, but that is a likely cause, not a confirmed one. | |||
S5 and SUS: standby 2
Come up once the always-on rails are good, before the power button.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S5 | – | 3.300 | – |
AI: what PP3V3_S5 is and how to check itPP3V3_S5 is the 3.3 V standby rail; the S5/SUS suffix in its name marks it as a standby rail, present before the board fully powers on. The archive lists a known-good voltage of 3.300 V; there is no known-good diode or resistance reading here for this net.
| |||
PPVIN_S5_HS_COMPUTING_ISNS | 0.431 | 12.600 | – |
AI: what PPVIN_S5_HS_COMPUTING_ISNS is and how to check it
| |||
S4 1
Follow as the board starts to wake.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP5V_S4 | – | 5.000 | – |
AI: what PP5V_S4 is and how to check it
| |||
S0: running 7
Only there when the machine is fully on.
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
PP3V3_S0 | 0.320 | – | – |
AI: what PP3V3_S0 is and how to check itPP3V3_S0 is the 3.3 V rail for the S0 (running) state, inferred from its name; it should be present once the board is fully on. The archive lists one known-good reading: diode 0.320 in diode mode to ground, with no condition noted. Check it unpowered in diode mode from the rail to ground, then power the board and measure the voltage at the rail. No known-good voltage reading is recorded here, so compare against a matching rail or a known-good board. A diode reading far from 0.320 usually points to a short or a leaky part on that rail, but one reading alone doesn't confirm a fault. | |||
PPBUS_S0_LCDBKLT_PWR_SW | 0.864 | – | – |
AI: what PPBUS_S0_LCDBKLT_PWR_SW is and how to check it
| |||
PPVCC_S0_CPU | 0.005 | 1.700 | 5.000R |
AI: what PPVCC_S0_CPU is and how to check itPPVCC_S0_CPU is the CPU core power rail; the S0 in the name indicates it is active in the running state. The archive lists a known-good diode reading of 0.005 and 1.700 V, with 5.000R resistance; these are community readings and only a guide. Check it with the board unpowered in diode mode from the rail to ground, then measure the voltage with power applied. A diode reading far from 0.005 usually points to a short or a damaged component on the rail, but one reading alone doesn't confirm a fault. No known-good current draw or ripple value is available here. | |||
PPVCC_S0_CPU_PH1 | – | – | 11.00R |
AI: what PPVCC_S0_CPU_PH1 is and how to check itPPVCC_S0_CPU_PH1 is a CPU power rail; the S0 in the name indicates the running state, and PH1 suggests one phase of a multiphase CPU supply (general reading of the name, not from board data). The only known-good figure here is 11.00R resistance; no known-good diode or voltage reading is recorded for this rail. With the board unpowered, measure diode mode from the rail to ground, then apply power and check the voltage. A resistance far from 11.00R, or a near-short in diode mode, usually points to a fault on the rail or its load, but one reading alone doesn't confirm a bad part. | |||
PPVCC_S0_CPU_PH2 | – | – | 11.00R |
AI: what PPVCC_S0_CPU_PH2 is and how to check itPPVCC_S0_CPU_PH2 is a CPU power rail, and the "S0" in its name indicates it is active in the running state. The only known-good reading here is 11.00R in resistance mode; there is no known-good diode or voltage value for this rail. With the board unpowered, measure diode mode to ground and compare against a matching phase net on the other side of the CPU power pair, since no diode value is listed. Then apply power and check the voltage, again with no known-good figure to compare against. A resistance far from 11.00R usually points to a short or open on that phase, but one reading alone doesn't confirm a bad part. | |||
PPVCC_S0_CPU_PH3 | – | – | 11.00R |
AI: what PPVCC_S0_CPU_PH3 is and how to check itPPVCC_S0_CPU_PH3 is a CPU power rail; the "S0" in the name indicates it belongs to the running (S0) state, and "PH3" suggests a phase of the CPU VRM output. The only known-good figure here is a resistance of 11.00R, with no condition noted; there is no known-good diode or voltage reading for this rail. Check it unpowered in resistance or diode mode from the rail to ground, then measure the voltage with the board powered and running. A resistance far from 11.00R usually points to a short or open on the rail or its load, but a single reading isn't proof a part is bad. | |||
PPVOUT_S0_LCDBKLT | 1.196 | – | – |
AI: what PPVOUT_S0_LCDBKLT is and how to check itPPVOUT_S0_LCDBKLT is the LCD backlight output rail; the name indicates an S0 (running-state) supply, and "LCDBKLT" points to the panel backlight boost output. The only known-good reading here is a diode value of 1.196 to ground, with no condition noted; there is no known-good voltage reading in this data. Check it unpowered in diode mode from the rail to ground, then measure the DC voltage with the board powered and the display connected. A diode reading far below 1.196 usually suggests a short or leaky load on the backlight output, while a correct diode reading with no voltage points back toward the backlight driver or its enable. These are general guidelines, not confirmed causes. | |||
Every net with a reading
| Net | Diode | Voltage | Resistance |
|---|---|---|---|
AUD_CONN_HP_LEFT | 1.300 | – | – |
AUD_CONN_HP_RIGHT | 1.300 | – | – |
AUD_CONN_RING2_XW | 0.000 | – | – |
AUD_CONN_SLEEVE_XW | 0.000 | – | – |
AUD_CONN_TIPDET_1 | 1.790 | – | – |
AUD_CONN_TIPDET_2 | 1.300 | – | – |
AUD_CONN_TYPEDET | 0.760 | – | – |
CPUVR_PHASE1 | – | – | 11.00R |
CPUVR_PHASE2 | – | – | 11.00R |
CPUVR_PHASE3 | – | – | 11.00R |
GFXIMVP6_OCSET | 0.708 | – | – |
P3V3S5_LL | – | 3.300 | – |
P5VS4_VSW | – | 5.000 | – |
PP3V3_S0 | 0.320 | – | – |
PP3V3_S5 | – | 3.300 | – |
PP5V_S4 | – | 5.000 | – |
PP20V_DCIN_FUSE | – | 20.000 | – |
PPBUS_S0_LCDBKLT_PWR_SW | 0.864 | – | – |
PPDCIN_G3H | – | 20.000 | – |
PPDCIN_G3H_CHGR | – | 20.000 | – |
PPVCC_S0_CPU | 0.005 | 1.700 | 5.000R |
PPVCC_S0_CPU_PH1 | – | – | 11.00R |
PPVCC_S0_CPU_PH2 | – | – | 11.00R |
PPVCC_S0_CPU_PH3 | – | – | 11.00R |
PPVIN_S5_HS_COMPUTING_ISNS | 0.431 | 12.600 | – |
PPVOUT_S0_LCDBKLT | 1.196 | – | – |
SPDIF_OUT_JACK | 0.660 | – | – |
UNCONNECTED_18 | 1.790 | – | – |
Community readings and notes from OpenBoardData, released under the Open Database License, snapshot of 2026-11-04. Readings vary with a board's state and the meter, so treat them as a guide.
Frequently asked questions
What should PP3V3_S5 read on the 820-00138?
OpenBoardData's known-good values for PP3V3_S5 on the 820-00138: voltage 3.300. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP5V_S4 read on the 820-00138?
OpenBoardData's known-good values for PP5V_S4 on the 820-00138: voltage 5.000. Readings vary with the board's state and the meter, so treat them as a guide.
What should PP3V3_S0 read on the 820-00138?
OpenBoardData's known-good values for PP3V3_S0 on the 820-00138: diode 0.320. Readings vary with the board's state and the meter, so treat them as a guide.
How do I see these readings on my 820-00138 board?
Open your own 820-00138 boardview file in the free Board Viewer at aiwebcenter.com/tools/board-viewer/. If the board number is in the file's name, these readings load by themselves: hover over a pin to see them, and compare your meter. The file stays on your computer.
Where do these readings come from?
From OpenBoardData, a community archive of known-good diode, voltage and resistance readings and repair notes, released under the Open Database License. This page shows its snapshot of November 4, 2026. To add or correct a reading, use OpenBoardData's own site.
Sources
- OpenBoardData. Known-good readings and repair notes; community data under the Open Database License